Interface sheet - Edan EC-12 EXPRESS - CPET treadmill
Service documentation
Lode BV
Zernikepark 16
NL 9747 AN Groningen
The Netherlands
t: +31 50 571 28 11
f: +31 50 571 67 46
@: [email protected]
www.lode.nl
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
Table of contents
1 - List of symbols used
3
2 - Validity
3
3 - Setup instructions Edan EC12 Express
4
3.1 - Cable selection
4
3.2 - Software Setup
4
3.3 - Ergometer setup
5
4 - Setting up the hardware
6
4.1 - Connection overview
6
4.2 - Connecting with the usb cable
7
4.3 - Connecting with the RS232 cable
7
5 - Treadmill or ergometer with 3.5" touch screen unit
8
6 - Treadmill or ergometer with 7" touch screen control unit
13
7 - Nummerical Control Unit - Treadmill only
17
8 - Treadmill or Bicycle without control unit
19
8.1 - Device without control unit
19
1 - List of symbols used
Next
Previous
2 - Validity
This interface form covers
* All OEM treadmills manufactured by Lode B.V. with the part number 939900/01/02/07/08/09/10
starting from serial #939900-20090001;
* All Katana treadmills 9349XX-201X0001
* All Valiant treadmills starting with serial number 932900-20122XXX and 9329XX-20121XXX
* All Valiant 2 treadmill starting with serial number 9389xx-20140001
If your treadmill or ergometer is not covered by this interface form please contact Lode service
[email protected]
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
3/22
3 - Setup instructions Edan EC12 Express
3.1 - Cable selection
You will need the RS-232 cable
(part no. MS1R- 107242,
provided by EDAN) Express to
establish communication
between the Lode Treadmill
Valiant and SE-12 Express.
Connect the RS232 cable to the
SE-12 (picture).
Connect the cable to the
ergometer as described in
chapter "Hardware setup".
3.2 - Software Setup
4. Select TMX425 in the Device Model pull-down list.
5. Press the OK key.
1. Switch on SE-12 Express and
start program.
2. Click on the General Info key
on the System Setup interface.
3. Select Treadmill in the Device
Type pull-down list.
The Edan ECG is now ready for communication with the Treadmill.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
4/22
3.3 - Ergometer setup
The following protocol needs to be set in the Lode ergometer to communicate with the external
equipment.
Treadmill ergometer: Trackmaster
The next chapters describe the procedures to setup these protocols depending on the type of
ergometer.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
5/22
4 - Setting up the hardware
Lode ergometers have two ways of connecting external devices. The cable selection depends on the
connection possibilities of the external device. The previous chapter tells you which cable you need. This
can be a RS232 cable or a USB cable.
4.1 - Connection overview
Connect the cable to the USB
port if you are using a USB
cable.
Please note that you may have
to install the FTDI driver on the
external equipment. This
procedure is only needed if
windows fails to instal the driver
automatically.
You can find the driver on the
Lode website under the Services
tab.
Locations:
- For the Treadmill the communication ports are Located on the front side near the power switch.
- For the bicycle ergometer the communication ports are located on the bottom of the bicycle. Tilt the
ergometer on it's side to be able to acces these ports.
Communication Module:
Use the single RS232 port to connect the communication module to the external equipment.
Legacy communication card (picture above -> 1 * USB, 2 * RS232)
In case you are using a RS232 cable you must use the RS232 port closest
to the USB connector, on the picture indicated with RS232 (1).
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
6/22
4.2 - Connecting with the usb cable
If there is no other connection available you can also use a USB cable to
connect.
1. You will need an USB A to B cable (Lode part no. 930916) to establish
communication between the Lode ergometer and your stress system or
ergospirometrysystem. See picture left.
2. Connect the cable to the Lode ergometer.
3. Connect the cable to the external device.
4.3 - Connecting with the RS232 cable
Connecting with the RS232 cable
1. Depending on the external device you may need to use a straight
RS232 cable (Lode part no. 930911) or a cross linked cable. The cable
selection chapter specifies which cable is needed.
2. Connect the cable to the Lode ergometer.
3. Connect the cable to the external device.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
7/22
5 - Treadmill or ergometer with 3.5" touch screen unit
Start the Lode ergometer.
During start up information
about the ergometer, like the
kind of device, the serial
number and the connected
modules is displayed.
After initialisation the terminal
mode is automatically
displayed. Swipe with your
finger over the screen as
indicated with the red arrow in
the picture to go to the main
menu.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
8/22
Select "Settings" to change
settings of the device.
You can choose your Language
in the "Language" menu. The
menu "Sleep Mode" sets a
screensaver. The menu
"Terminal Settings" lets you set
the communication settings for
external communication. The
menu "Service" is only intended
for service purposes to be
executed by factory trainend
personel.
Select "Terminal Settings" to
change the communication
protocol.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
9/22
Select the Communication
protocol as desribed in
"Ergometer setup" chapter.
Select "Default" for the
baudrate.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
10/22
Select "RS232" or "USB"
depending in which cable you
have connected to the Lode
ergometer.
Select the button with the house
to go back to the main menu.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
11/22
Select "Terminal" to set the
ergometer in terminal mode.
Your device is now ready for
external control.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
12/22
6 - Treadmill or ergometer with 7" touch screen control unit
Start the device. Information
about the device is shown on
the display during boot mode.
After boot up the device shows
the Test window or main menu.
To access the menu from the
Test window you need to swipe
the graph area of the touch
screen as indicated in the
picture.
*Note that for this instruction
the graphic view for a Lode
Corival is used. The view for a
treadmill might difer a bit but
the procedure is the same.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
13/22
Select "settings" to go to the
settings menu.
Scroll down using the red
marked scroll button and select
"Terminal".
Select the communication
protocol ad described in the
"Ergometer setup" chapter.
Use the scroll button to view the
complete list.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
14/22
Select "Default" for the
baudrate.
Select "RS232"or "USB"
depending on the type of cable
that you connected to the Lode
ergometer.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
15/22
Press the home button on the
left bottom corner and select
"Terminal". Your ergometer is
now ready for external
communication.
on. It will boot directly into terminal mode.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
*optional*
Your ergometer can be set to
boot up in terminal mode.
Follow these steps to activate
this function:
- Go to the settings menu
- Select "Default Start Menu"
- Select "Terminal"
- Switch the ergometer off and
16/22
7 - Nummerical Control Unit - Treadmill only
1. Press and hold key #1 and #2
as shown on "Figure 1" for 10
seconds.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
17/22
2. Press the enter key #4 until the display shows terminal 0
3. By using the "+" and "-" keys for the grade adjustment #3 you can change the "0" behind terminal to
"1" to activate the Terminal mode.
4. Press enter #4 and "prot id" will be shown on the display, for Lode protocol this should be set to "1".
Set the protocol as described in the "Ergometer setup" chapter.
The following protocols can be selected
Lode = Lode protocol
trAck = Trackmaster communication protocol
UUood = Woodway communication protocol
HPcoS = HP Cosmos communication protocol
gE = GE protocol
5. Press enter #4 and "baudrate" will be displayed to set the correct baudrate, select "0" for auto select.
The following baudrates can be set:
Baudrate = 0 (Autoselect dependent on protocol-id)
2400;
4800;
9600;
19200;
38400;
57600
6. Press enter #4 and "interface" will be displayed, you can choose the communication port which you
would like to select.
Interface = CIM interface choice. Select "RS232" or "USB" depending on the cable that you connected to
the treadmill.
0 = RS232
1 = RS232-AUX
2 = USB
7. Press enter #4; the next step "Neg Elev" is read only and is "1" when a negative elevation option has
been added to the treadmill, without a negative elevation option this value shows "0".
Neg Elev = Negetive elevation (read-only)
0 = not present
1 = present
Press the stop button #2 on the control unit or wait 10 seconds to leave the settings menu and let your
changes take effect.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
18/22
8 - Treadmill or Bicycle without control unit
8.1 - Device without control unit
In case the device does not have a control unit the correct protocol can be set from a computer by using
the Lode Service Manager tool that can be downloaded from the Lode website if you are a registered
user. http://lode.nl/en/product/getDownload/469
Connect an USB cable from the computer to the USB port of the treadmill or use a RS232 cable from the
computer to the RS232 port
Start the Lode Service Manager and login with the same account details that you use to login on the
website.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
19/22
1. Select Terminal
2. Choose Setup to select the
COM port on which the device is
connected.
3. Select preset Lode Bus
Service Protocol
4. Press OK
5. Press Break
6. Switch the device off, wait 10
seconds
7. Switch the device on
The screen as shown left should
show up within 5 seconds after
powering up.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
20/22
A menu is showed. use the
nummerical keys to make your
selection. The next menu will
automatically come up when a
number is pushed.
Select settings (1) and choose
the protocol as described in the
"Ergometer set-up" chapter.
Choose which port you want to
use RS232 (0) or USB (1)
This setting refers to the type of
cable that you have connected
to the Lode ergometer.
Select default for the baudrate.
Note that Default should always
be selected unless different
specified by your dealer.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
21/22
Select the kmh/kmh (1)
conversion for if you are using
the Trackmaster protocol.
If you are using a protocol other
than Trackmaster select "no
conversion" (0).
Select "Disable" (0) for Global
communication timeout.
Press "Y" to save the new
settings and restart the device.
Your device is now ready for use
with the external controller.
Note that the device is
automatically switched to
terminal mode when no manual
controller is present at the
device itself.
INTERFACE SHEET - EDAN EC-12 EXPRESS - CPET TREADMILL / VERSION: 1.0 - 2015-10-22
22/22
">
