Apple Pavilion g6-2000 Specifications

Apple Pavilion g6-2000 Specifications
HP Pavilion g6 Notebook PC
Maintenance and Service Guide
SUMMARY
This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides
comprehensive information on identifying computer features, components, and spare parts;
troubleshooting computer problems; and performing computer disassembly procedures.
© Copyright 2012 Hewlett-Packard
Development Company, L.P.
AMD is a trademark of Advanced Micro
Devices, Inc. Bluetooth is a trademark
owned by its proprietor and used by
Hewlett-Packard Company under license.
Intel, Centrino, Core, and Pentium are
trademarks of Intel Corporation in the U.S.
and other countries. Microsoft and Windows
are U.S. registered trademarks of Microsoft
Corporation. SD Logo is a trademark of its
proprietor.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
First Edition: March 2012
Document Part Number: 677574-001
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on
a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to
contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer
and the AC adapter comply with the user-accessible surface temperature limits defined by the
International Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv
Safety warning notice
Table of contents
1 Product description ........................................................................................................................................ 1
2 External component identification ................................................................................................................ 5
Display .................................................................................................................................................. 5
Top ....................................................................................................................................................... 6
Buttons and speakers .......................................................................................................... 6
Keys ..................................................................................................................................... 7
Lights ................................................................................................................................... 8
TouchPad ............................................................................................................................ 9
Left side .............................................................................................................................................. 10
Right side ........................................................................................................................................... 11
Bottom components ........................................................................................................................... 12
3 Illustrated parts catalog ............................................................................................................................... 13
Serial number location ........................................................................................................................ 13
Computer major components ............................................................................................................. 14
Display assembly components ........................................................................................................... 18
Mass storage devices ......................................................................................................................... 19
Miscellaneous parts ............................................................................................................................ 20
Sequential part number listing ............................................................................................................ 21
4 Removal and replacement procedures ....................................................................................................... 25
Preliminary replacement requirements ............................................................................................... 25
Tools required .................................................................................................................... 25
Service considerations ....................................................................................................... 25
Plastic parts ....................................................................................................... 25
Cables and connectors ..................................................................................... 25
Drive handling ................................................................................................... 26
Grounding guidelines ......................................................................................................... 26
Electrostatic discharge damage ........................................................................ 26
Packaging and transporting guidelines ............................................. 28
Component replacement procedures ................................................................................................. 29
Service label ...................................................................................................................... 30
Computer feet .................................................................................................................... 30
Battery ............................................................................................................................... 32
Service door ....................................................................................................................... 33
v
Optical drive ....................................................................................................................... 34
Hard drive .......................................................................................................................... 36
Replacing the hard drive ................................................................................... 38
Installing a hard drive with an operating system ............................... 38
Installing a hard drive without an operating system .......................... 38
Memory module ................................................................................................................. 39
WLAN module .................................................................................................................... 42
Keyboard ........................................................................................................................... 44
Top cover ........................................................................................................................... 48
Speakers ............................................................................................................................ 51
Power button board ........................................................................................................... 52
TouchPad button board ..................................................................................................... 54
TouchPad LED board ........................................................................................................ 55
Display assembly ............................................................................................................... 57
Optical drive cable ............................................................................................................. 63
USB board ......................................................................................................................... 64
Power connector ................................................................................................................ 65
System board ..................................................................................................................... 66
RTC battery ....................................................................................................................... 69
Fan and heat sink .............................................................................................................. 70
PCH heat sink .................................................................................................................... 73
Processor ........................................................................................................................... 74
5 Specifications ................................................................................................................................................ 76
Computer specifications ..................................................................................................................... 76
39.6-cm (15.6-in) display specifications ............................................................................................. 77
Hard drive specifications .................................................................................................................... 78
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive specifications .................................. 79
Blu-ray Disc ROM and DVD±R/RW SuperMulti Double-Layer Drive specifications ........................... 80
6 Setup Utility (BIOS) ....................................................................................................................................... 81
Starting Setup Utility ........................................................................................................................... 81
Using Setup Utility .............................................................................................................................. 81
Changing the language of Setup Utility ............................................................................. 81
Navigating and selecting in Setup Utility ............................................................................ 81
Displaying system information ........................................................................................... 82
Restoring factory default settings in Setup Utility .............................................................. 82
Exiting Setup Utility ............................................................................................................ 82
Updating the BIOS ............................................................................................................................. 83
Determining the BIOS version ........................................................................................... 83
Downloading a BIOS update ............................................................................................. 83
vi
7 Backing up, restoring, and recovering ....................................................................................................... 85
Creating backups ............................................................................................................................... 85
Creating recovery media to recover the original system .................................................... 85
What you need to know ..................................................................................... 85
Creating the recovery media ............................................................ 86
Creating system restore points .......................................................................................... 86
What you need to know ..................................................................................... 86
Creating a system restore point ........................................................................ 86
Backing up system and personal information .................................................................... 86
Tips for a successful backup ............................................................................. 87
What you need to know ..................................................................................... 87
Creating a backup using Windows Backup and Restore .................................. 87
Restore and recovery ......................................................................................................................... 88
Restoring to a previous system restore point .................................................................... 88
Restoring specific files ....................................................................................................... 88
Restoring specific files using Windows Backup and Restore ............................ 88
Recovering the original system using HP Recovery Manager ........................................... 88
What you need to know ..................................................................................... 88
Recovering using HP Recovery partition (select models only) ......................... 89
Recovering using the recovery media ............................................................... 89
Changing the computer boot order ................................................... 89
8 Power cord set requirements ...................................................................................................................... 91
Requirements for all countries ............................................................................................................ 91
Requirements for specific countries and regions ............................................................................... 92
9 Recycling ....................................................................................................................................................... 94
Index ................................................................................................................................................................... 95
vii
viii
1
Product description
Category
Description
Product Name
HP Pavilion g6 Notebook PC
Processors
2nd Generation Intel Core Processors:
Intel Core i5-2450M processor (2.5 GHz, SC turbo up to 3.1 GHz, 3 MB L3 cache),
Dual 35 W
Intel Core i3-2350M processor (2.3 GHz, 3 MB L3 cache) Dual 35 W
Intel Core i3-2330M processor (2.2 GHz, 3 MB L3 cache) Dual 35 W
Intel Pentium® processors:
Intel Pentium B960 processor (2.2 GHz, 2 MB L3 cache) Dual 35 W
Chipset
Intel HM76 Express Chipset
Graphics
Internal Graphics (UMA):
Intel HD Graphics 3000 (2nd Generation Processors)
Intel HD Graphics (Pentium Processors)
Switchable Discrete Graphics:
Supports HD decode, Dx10, and HDMI
AMD Radeon HD 7670M with 1024 MB of dedicated video memory
AMD Radeon HD 7670M with 2048 MB of dedicated video memory
Panel
39.6-cm (15.6-in) HD LED BrightView (1366×768)
16:9 wide aspect ratio
Memory
2 customer-accessible/upgradable SODIMM slots:
●
DDR3-1333 MHz Dual Channel Support (DDR3-1600 MHz downgrade to
DDR3-1333 MHz)
Supports the following configurations up to 8 GB:
Hard drives
●
8192 MB total system memory (4096×2) (No support for 32 bit OS)
●
6144 MB total system memory (4096×1 + 2048×1) (No support for 32 bit OS)
●
4096 MB total system memory (4096×1 or 2048×2)
●
2048 MB total system memory (2048×1)
Supports 6.35 cm (2.5 in) hard drives in 9.5 mm (.37 in) and 7.0 mm (.28 in)
thicknesses
Supports HP 3D Drive Guard
Customer-accessible
Serial ATA (SATA)
1
Category
Description
Supports the following single hard drive configurations:
Optical drive
●
1 TB, 5400 rpm, 9.5 mm
●
750 GB, 7200 rpm, 9.5 mm
●
750 GB, 5400 rpm, 9.5 mm
●
640 GB, 5400 rpm, 9.5 mm
●
500 GB, 7200 rpm, 9.5 mm
●
500 GB, 5400 rpm, 9.5 mm
●
320 GB, 7200 rpm, 9.5 mm and 7.0 mm
●
320 GB, 5400 rpm, 9.5 mm and 7.0 mm
Fixed
Customer-accessible
SATA
12.7 mm tray load
Supports Blu-ray ROM DVD±R/RW Super Multi Double-Layer Drive
Supports DVD±RW Super Multi Double-Layer Combo Drive
Supports zero-power optical drive
Webcam
VGA camera (640x480 by 24 frames per second), fixed angle (no tilt), with activity
light and single digital microphone
Audio
High-definition audio supports:
Microsoft® Premium requirements with HP Altec Lansing speakers (2)
SRS Premium Sound technology
Ethernet
Integrated 10/100 network interface card (NIC)
Wireless
Integrated wireless local area network (WLAN) options by way of wireless module
Customer-accessible
Two WLAN antennas built into display assembly
Support for Intel Wireless Display and Wireless Music
Support for the following WLAN formats:
2
Chapter 1 Product description
●
Atheros 9485GN 802.11b/g/n 1×1 WiFi Adapter and 3012 Bluetooth 4.0 Combo
Adapter (select models only)
●
Atheros HB125 802.11b/g/n 1×1 WiFi Adapter (select models only)
●
Broadcom 4313GN 802.11b/g/n 1×1 WiFi and 20702 Bluetooth 4.0 Combo
Adapter
●
Intel Centrino® Wireless-N 2230 802.11b/g/n 2×2 WiFi and Bluetooth Combo
Adapter
●
Ralink RT5390F 802.11b/g/n 1×1 WiFi Adapter
●
Ralink RT5390BC8 802.11b/g/n 1×1 WiFi and Bluetooth 3.0+HS Combo Adapter
Category
Description
External media card
HP Multi-Format Digital Media Reader supports the following digital card formats:
●
MultiMediaCard (MMC)
●
Secure Digital (SD) Memory Card
●
Secure Digital High Capacity (SDHC) Memory Card
●
Secure Digital Extended Capacity (SDXC) Memory Card
Internal card
One half-size Mini Card slot for WLAN
Ports
●
Audio-in (digital microphone)
●
Audio-out (stereo headphone)
●
RJ-45 (Ethernet, includes link and activity lights)
●
USB 3.0 ports (two on left side)
●
USB 2.0 port (right side)
●
VGA (Dsub 15-pin) supporting:
Keyboard/pointing devices
◦
2048×1536 external resolution @ 75 Hz
◦
Hot plug/unplug with auto-detect for correct output to wide-aspect vs.
standard aspect video
●
High-Definition Multimedia Interface (HDMI) version 1.4 supporting up to
1920x1200 @ 60 Hz
●
AC Smart Pin adapter
Full size island style textured keyboard with numeric keypad (Black)
TouchPad with 2 buttons
Power requirements
●
Multitouch gestures enabled
●
Taps enabled as default
Battery:
●
6-cell, 2.22 Ah, 47 Wh battery
●
6-cell, 2.55 Ah, 55 Wh battery (select models only)
●
Supports fast charge
AC Smart pin adapter with localized cable plug support:
Security
●
65 W
●
90 W
Security lock slot
3
Category
Description
Operating system
Preinstalled:
Serviceability
4
Chapter 1 Product description
●
Windows® 7 Professional (64 bit)
●
Windows 7 Home Premium (64 bit)
●
Windows 7 Home Basic (64 bit)
●
FreeDOS
End-user replaceable parts:
●
AC adapter
●
Battery (system)
●
Memory module
●
Hard drive
●
Optical drive
●
MiniCard components
●
Keyboard
2
External component identification
Display
Item
Component
Description
(1)
WLAN antennas (2)*
Send and receive wireless signals to communicate
with WLAN devices.
(2)
Internal microphone
Records sound.
(3)
Webcam
Records video and captures still photographs. To use
the webcam, select Start > All Programs >
CyberLink YouCam > CyberLink YouCam.
(4)
Webcam light
On: The webcam is in use.
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately
around the antennas free from obstructions. To see wireless regulatory notices, refer to the section of the Regulatory, Safety,
and Environmental Notices that applies to your country or region. These notices are located in Help and Support.
Display
5
Top
Buttons and speakers
Component
(1)
Description
Power button
●
When the computer is off, press the button to turn on
the computer.
●
When the computer is on, press the button briefly to
initiate Sleep.
●
When the computer is in the Sleep state, press the
button briefly to exit Sleep.
●
When the computer is in Hibernation, press the button
down briefly to exit Hibernation.
CAUTION: Pressing and holding down the power button
will result in the loss of unsaved information.
If the computer has stopped responding and Microsoft
Windows shutdown procedures are ineffective, press and
hold the power button down for at least 5 seconds to turn
off the computer.
To learn more about your power settings, select Start >
Control Panel > System and Security > Power Options,
or see the HP User Guide.
(2)
6
Speakers (2)
Chapter 2 External component identification
Produce sound.
Keys
Component
Description
(1)
esc key
Displays system information when pressed in combination
with the fn key.
(2)
fn key
Displays system information when pressed in combination
with the esc key.
(3)
Windows logo key
Displays the Windows Start menu.
(4)
Action keys
Execute frequently used system functions.
(5)
Windows applications key
Displays a shortcut menu for items beneath the cursor.
(6)
num lock
Alternates between the navigational and numeric functions
on the integrated numeric keypad.
NOTE: The keypad function that is active when the
computer is turned off remains on when the computer is
turned back on.
(7)
Integrated numeric keypad
Can be used like an external numeric keypad.
Top
7
Lights
Component
(1)
Power light
●
White: The computer is on.
●
Blinking: The computer is in Sleep mode.
●
Off: The computer is off or in Hibernation mode.
(2)
Caps lock light
White: Caps lock is on, which switches the keys to all capital
letters.
(3)
Mute light
●
Amber: Computer sound is off.
●
Off: Computer sound is on.
●
White: An integrated wireless device, such as a
wireless local area network (WLAN) device and/or a
Bluetooth® device, is on.
●
Amber: All wireless devices are off.
●
Amber: The TouchPad is off.
●
Off: The TouchPad is on.
(4)
(5)
8
Description
Wireless light
TouchPad light
Chapter 2 External component identification
TouchPad
Component
Description
(1)
TouchPad on/off button
Turns the TouchPad on or off.
(2)
TouchPad light
●
Amber: The TouchPad is off.
●
Off: The TouchPad is on.
(3)
TouchPad zone
Moves the on-screen pointer and selects or activates items
on the screen.
(4)
Left TouchPad button
Functions like the left button on an external mouse.
(5)
Right TouchPad button
Functions like the right button on an external mouse.
Top
9
Left side
Component
Description
(1)
External monitor port
Connects an external VGA monitor or projector.
(2)
Vents (2)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(3)
HDMI port
Connects an optional video or audio device, such as a
high-definition television, or any compatible digital or audio
device.
(4)
RJ-45 (network) jack
Connects a network cable.
(5)
USB 3.0 ports (2)
Connect optional USB 3.0 compatible devices and provide
enhanced USB power performance.
(6)
Audio-in (microphone) jack
Connects an optional computer headset microphone,
stereo array microphone, or monaural microphone.
(7)
Audio-out (headphone) jack
Connects optional powered stereo speakers, headphones,
earbuds, a headset, or a television audio cable.
WARNING! To reduce the risk of personal injury, adjust
the volume before using headphones, earbuds, or a
headset. For additional safety information, see the
Regulatory, Safety and Environmental Notices.
NOTE: When a device is connected to a headphone jack,
the computer speakers are disabled.
(8)
10
Digital media slot
Chapter 2 External component identification
Supports the following digital card formats:
●
Secure Digital (SD) Memory Card
●
Secure Digital Extended Capacity (SDxC) Memory
Card
●
Secure Digital High Capacity (SDHC) Memory Card
●
MultiMediaCard (MMC)
Right side
Component
Description
(1)
Optical drive
Reads and writes to an optical disc.
(2)
Optical drive light
●
Green or amber: The optical drive is being accessed.
●
Off: The optical drive is idle.
(3)
Optical drive eject button
Releases the disc tray.
(4)
Power light
●
White: The computer is on.
●
Blinking white: The computer is in the Sleep state,
which is an energy-saving mode. The computer shuts
off power to the display and other unneeded
components.
●
Off: The computer is off or in Hibernation. Hibernation
is an energy-saving mode that uses the least amount
of power.
●
Blinking white: The hard drive is being accessed.
●
Amber: HP 3D DriveGuard has temporarily parked the
hard drive.
(5)
Hard drive light
(6)
USB 2.0 port
Connects an optional USB 2.0 compatible device.
(7)
AC adapter light
●
White: The AC adapter is connected and the battery is
charged.
●
Blinking white: The battery has reached a low battery
level.
●
Amber: The AC adapter is connected and the battery
is charging.
●
Off: The computer is using DC power.
(8)
Power connector
Connects an AC adapter.
(9)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from being
mishandled or stolen.
Right side
11
Bottom components
Component
Description
(1)
Battery bay
Holds the battery.
(2)
Battery release latch
Releases the battery from the battery bay.
(3)
Vents (5)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(4)
Service door
Provides access to the keyboard, optical drive, hard drive,
wireless module, and memory modules.
CAUTION: To prevent an unresponsive system, replace
the wireless module only with a wireless module authorized
for use in the computer by the governmental agency that
regulates wireless devices in your country or region. If you
replace the module and then receive a warning message,
remove the module to restore computer functionality, and
then contact customer support through Help and Support.
12
Chapter 2 External component identification
3
Illustrated parts catalog
Serial number location
When ordering parts or requesting information, provide the computer serial number and model
number located in the battery bay of the computer.
Component
Description
(1)
Product name
The name affixed to the front of the computer.
(2)
Serial number (s/n)
An alphanumeric identifier that is unique to each product.
(3)
Product number
This number provides specific information about the product’s
hardware components. The product number helps a service
technician to determine what components and parts are needed.
(4)
Warranty period
The duration of the warranty period for the computer.
(5)
Model description (select models only)
An alphanumeric identifier used to locate documents, drivers, and
support for the computer.
Serial number location
13
Computer major components
14
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
(1)
39.6-cm (15.6-in) High Definition (HD), LED, BrightView (1366×768) display
assembly:
NOTE: For more information on the display assembly internal component spare part
information, see Display assembly components on page 18.
(2)
(3)
Keyboard (includes keyboard cable):
●
For use in the United States, Black
681800-001
●
For use in the United Kingdom, Black
681800-031
●
For use in Germany, Black
681800-041
●
For use in France, Black
681800-051
●
For use in Italy, Black
681800-061
●
For use in Spain, Black
681800-071
●
For use in Portugal, Black
681800-131
●
For use in Turkey, Black
681800-141
●
For use in Greece, Black
681800-151
●
For use in Saudi Arabia, Black
681800-171
●
For use in Hungary, Black
681800-211
●
For use in Russia, Black
681800-251
●
For use in Europe, Black
681800-A41
●
For International use, Black
681800-B31
●
For use in the Adriatics, Black
681800-BA1
●
For use in Israel, Black
681800-BB1
●
For use in Switzerland, Black
681800-BG1
●
For use in the Netherlands, Black
681800-DH1
●
For use in Bulgaria, Black
681800-261
●
For use in Romania, Black
681800-271
●
For use in Thailand, Black
681800-281
●
For use in Japan, Black
681800-291
●
For use in Taiwan, Black
681800-AB1
●
For use in Korea, Black
681800-AD1
●
For use in the Adriatics, Black
681800-FL1
●
For use in Canada, Black
681800-DB1
●
For use in Canada, Linen White
684689-DB1
●
For use in United States, Linen White
684689-001
Top cover (includes TouchPad board):
●
For use in Ruby Red computer models
681823-001
Computer major components
15
Item
Description
Spare part number
●
For use in Winter Blue computer models
681824-001
●
For use in Sparkling Black computer models
681825-001
(4)
Power button board (includes cable)
683549-001
(5)
TouchPad LED board (includes cable)
684061-001
(6)
TouchPad button board (includes cable)
683548-001
(7)
Speaker assembly (includes cable)
681821-001
(8)
System board (includes replacement thermal material):
●
For use only with computer models equipped with UMA video memory
680568-001
●
For use only with computer models equipped with 1024 MB of dedicated discrete
video memory
680569-001
●
For use only with computer models equipped with 2048 MB of dedicated discrete
video memory
680570-001
(9)
Intel Platform Controller Hub (PCH) heat sink
(10)
Processor (includes replacement thermal material):
683843-001
●
Intel Core i5-2450M processor (2.5 GHz, SC turbo up to 3.1 GHz, 3 MB L3 cache),
Dual 35 W
676359-001
●
Intel Core i3-2350M processor (2.3 GHz, 3 MB L3 cache) Dual 35 W
653340-001
●
Intel Core i3-2330M processor (2.2 GHz, 3 MB L3 cache) Dual 35 W
653339-001
●
Intel Pentium B960 processor (2.2 GHz, 2 MB L3 cache) Dual 35 W
664662-001
(11)
RTC battery (includes mounting adhesive)
(12)
Heat sink assembly (includes replacement thermal material):
637193-001
●
For use in Intel UMA computer models
680549-001
●
For use in Intel discrete computer models
680550-001
●
Fan (available separately)
680551-001
(13)
Power connector (includes cable)
682744-001
(14)
USB board (includes cable)
683547-001
(15)
Optical drive cable
682742-001
(16)
Battery:
●
6-cell Li-lon, 2.20 Ah, 47 Wh
593553-001
●
6-cell Li-lon, 2.55 Ah, 55 Wh
593554-001
(17)
Base enclosure
(18)
Hard drive:
681805-001
Supports the following 9.5 mm, 6.35 cm (2.5 in) SATA hard drives:
16
●
1 TB, 5400 rpm, 9.5 mm
676521-001
●
750 GB, 7200 rpm
633252-001
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
●
640 GB, 5400 rpm
669300-001
●
500 GB, 7200 rpm
634925-001
●
500 GB, 5400 rpm
669299-001
●
320 GB, 7200 rpm
641672-001
●
320 GB, 5400 rpm
622643-001
Supports the following 7.0 mm, 6.35 cm (2.5 in) SATA hard drives:
(19)
(20)
(21)
(22)
●
320 GB, 7200 rpm
634862-001
●
320 GB, 5400 rpm
645193-001
●
Hard Drive Hardware Kit (not illustrated, includes hard drive cable, hard drive
bumpers, and hard drive bracket and screws)
682745-001
Memory modules (1066 MHz, DDR3):
●
4 GB PC3 12800 1600 MHz shared
641369-001
●
2 GB PC3 12800 1600 MHz shared
652972-001
Wireless (WLAN) module:
●
Atheros 9485GN 802.11b/g/n 1×1 WiFi Adapter and 3012 Bluetooth 4.0 Combo
Adapter (select models only)
655795-001
●
Ralink RT5390BC8 802.11b/g/n 1×1 WiFi and Bluetooth 3.0+HS Combo Adapter
656120-001
●
Broadcom 4313GN 802.11b/g/n 1×1 WiFi Adapter and 20702 Bluetooth 4.0+HS
Combo Adapter
657325-001
●
Intel Centrino Wireless-N 2230 802.11b/g/n 2×2 WiFi and Bluetooth Combo Adapter
670290-001
●
Ralink RT5390F 802.11b/g/n 1×1 WiFi Adapter
670691-001
●
Atheros HB125 802.11b/g/n 1×1 WiFi Adapter (select models only)
675794-001
Optical drive (includes optical drive bezel and bracket):
●
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive
681814-001
●
Blu-ray Disc ROM and DVD±R/RW SuperMulti Double-Layer Drive
681815-001
Service Door (included in Plastics kit)
681816-001
Rubber Kit (not illustrated, includes rubber feet)
680563-001
Computer major components
17
Display assembly components
Item
Description
Spare part number
(1)
Display bezel
681806-001
(2)
Webcam/microphone module
680577-001
(3)
Display hinge kit (includes left and right display hinges and brackets)
681812-001
(4)
39.6 cm (15.6-in) high-definition, BrightView LED display panel
681817-001
(5)
Wireless antenna (includes wireless antenna transceivers and cable)
681813-001
(6)
Display cable (included in the Display Cable Kit)
681808-001
(7)
Display hinge covers
681811-001
(8)
Display back cover (includes logo):
●
For use in Ruby Red computer models
681802-001
●
For use in Winter Blue computer models
681803-001
●
For use in computer Sparkling Black computer models
681804-001
Display Screw Kit (not illustrated)
18
Chapter 3 Illustrated parts catalog
681819-001
Mass storage devices
Item
Description
(1)
Optical drive (12.7 mm, SATA, fixed, includes bezel and bracket)
(2)
Spare part number
●
Blu-ray ROM DVD±R/RW Super Multi Double-Layer Drive
681814-001
●
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
681815-001
●
Optical drive cable
682742-001
Hard drive
Supports the following 9.50 mm, 6.35 cm (2.50 in) SATA hard drives:
●
1 TB, 5400 rpm
676521-001
●
750 GB, 7200 rpm
633252-001
●
750 GB, 5400 rpm
634250-001
●
640 GB, 5400 rpm
669300-001
●
500 GB, 7200 rpm
634925-001
●
500 GB, 5400 rpm
669299-001
●
320 GB, 7200 rpm
641672-001
●
320 GB, 5400 rpm
622643-001
Supports the following 7.00 mm, 6.35 cm (2.50 in) SATA hard drives:
●
320 GB, 7200 rpm
634862-001
●
320 GB, 5400 rpm
645193-001
Hard drive hardware kit (includes hard drive cable, hard drive bumpers, and hard
drive bracket and screws)
682745-001
Mass storage devices
19
Miscellaneous parts
Description
Spare part number
AC adapters
●
90 W HP Smart AC adapter with Power Factor Correction (PFC) (for computer models
equipped with a graphics subsystem with discrete memory only)
609940-001
●
65 W HP Smart AC adapter with PFC (for computer models equipped with a graphics
subsystem with UMA memory only)
609939-001
●
90 W HP Smart AC adapter with PFC (for select computer models equipped with a graphics
subsystem with discrete memory only)
609947-001
●
65 W HP Smart AC adapter (for select computer models equipped with a graphics subsystem
with UMA memory only)
609948-001
Power cord, AC, 3 wire, black, 1.83-m
20
●
For use in North America
490371-001
●
For use in Australia
490371-011
●
For use in Europe
490371-021
●
For use in the United Kingdom and Singapore
490371-031
●
For use in Italy
490371-061
●
For use in Switzerland
490371-111
●
For use in Denmark
490371-081
●
For use in Thailand
490371-201
●
For use in Japan
490371-291
●
For use in the People's Republic of China
490371-AA1
●
For use in Taiwan
490371-AB1
●
For use in South Korea
490371-AD1
●
For use in South Africa
490371-AR1
●
For use in Israel
490371-BB1
●
For use in India
490371-D61
Thermal pad
680571-001
Display screw kit
681819-001
Screw kit
681820-001
Chapter 3 Illustrated parts catalog
Sequential part number listing
Spare part number
Description
490371-001
Power cord, AC, 3 wire, black, 1.83 m for use in North America
490371-011
Power cord, AC, 3 wire, black, 1.83 m for use in Australia
490371-021
Power cord, AC, 3 wire, black, 1.83 m for use in Europe
490371-031
Power cord, AC, 3 wire, black, 1.83 m for use in the United Kingdom and Singapore
490371-061
Power cord, AC, 3 wire, black, 1.83 m for use in Italy
490371-081
Power cord, AC, 3 wire, black, 1.83 m for use in Denmark
490371-111
Power cord, AC, 3 wire, black, 1.83 m for use in Switzerland
490371-201
Power cord, AC, 3 wire, black, 1.83 m for use in Thailand
490371-291
Power cord, AC, 3 wire, black, 1.83 m for use in Japan
490371-AA1
Power cord, AC, 3 wire, black, 1.83 m for use in the People's Republic of China
490371-AB1
Power cord, AC, 3 wire, black, 1.83 m for use in Taiwan
490371-AD1
Power cord, AC, 3 wire, black, 1.83 m for use in Korea
490371-AR1
Power cord, AC, 3 wire, black, 1.83 m for use in South Africa
490371-BB1
Power cord, AC, 3 wire, black, 1.83 m for use in Israel
490371-D61
Power cord, AC, 3 wire, black, 1.83 m for use in India
593553-001
Battery, 6-cell, 2.20 Ah, 47 Wh
593554-001
Battery, 6-cell, 2.55 Ah, 55 Wh
609939-001
65 W AC adapter
609940-001
90 W AC adapter
609947-001
90 W AC adapter (EM)
609948-001
65 W AC adapter (EM)
622643-001
320 GB, 5400 rpm hard drive
633252-001
750 GB, 7200 rpm hard drive
634250-001
750 GB, 5400 rpm hard drive
634862-001
320 GB, 7200 rpm hard drive
634925-001
500 GB, 7200 rpm hard drive
637193-001
RTC battery (includes mounting adhesive)
641369-001
4 GB (PC3, 12800, 1600 MHz) memory module
641672-001
320 GB, 7200 rpm hard drive
645193-001
320 GB, 5400 rpm hard drive
652972-001
2 GB (PC3, 12800, 1600 MHz) memory module
653339-001
Intel Core i3-2330M processor (2.2 GHz, 3 MB L3 cache) Dual 35 W
Sequential part number listing
21
22
Spare part number
Description
653340-001
Intel Core i3-2350M processor (2.3 GHz, 3 MB L3 cache) Dual 35 W
655795-001
WLAN Atheros 9485GN 802.11b/g/n 1×1 WiFi Adapter and 3012 Bluetooth 4.0 Combo Adapter
(select models only
656120-001
WLAN Ralink RT5390BC8 802.11b/g/n 1×1 WiFi and Bluetooth 3.0+HS Combo Adapter
657325-001
WLAN Broadcom 4313GN 802.11b/g/n 1×1 WiFi Adapter and 20702 Bluetooth 4.0+HS Combo
Adapter
664662-001
Intel Pentium B960 processor (2.2 GHz, 2 MB L3 cache) Dual 35 W
669299-001
500 GB, 5400 rpm hard drive
669300-001
640 GB, 5400 rpm hard drive
670290-001
WLAN Intel Centrino Wireless-N 2230 802.11b/g/n 2×2 WiFi and Bluetooth Combo Adapter
670691-001
WLAN Ralink RT5390F 802.11b/g/n 1×1 WiFi Adapter
675794-001
WLAN Atheros HB125 802.11b/g/n 1×1 WiFi Adapter (select models only)
676359-001
Intel Core i5-2450M processor (2.5 GHz, SC turbo up to 3.3 GHz, 3 MB L3 cache), Dual 35 W
676521-001
1 TB, 5400 rpm hard drive
680549-001
Heat sink for use only with computer models equipped with UMA video memory
680550-001
Heat sink for use only with computer models equipped with Discrete video memory
680551-001
Fan
680563-001
Rubber Kit (includes rubber feet)
680568-001
System board for use only with computer models equipped with UMA video memory (includes
replacement thermal material)
680569-001
System board for use only with computer models equipped with a graphics subsystem with 1024 MB
of discrete video memory (includes replacement thermal material)
680570-001
System board for use only with computer models equipped with a graphics subsystem with 2048 MB
of discrete video memory (includes replacement thermal material)
680571-001
Thermal Material Kit (includes replacement thermal paste and pads)
680577-001
Webcam/microphone module
681800-001
Keyboard for use in the United States, black
681800-031
Keyboard for use in the United Kingdom, black
681800-041
Keyboard for use in Germany, black
681800-051
Keyboard for use in France, black
681800-061
Keyboard for use in Italy, black
681800-071
Keyboard for use in Spain, black
681800-131
Keyboard for use in Portugal, black
681800-141
Keyboard for use in Turkey, black
681800-151
Keyboard for use in for use in Greece, Black
681800-171
Keyboard for use in Saudi Arabia, black
Chapter 3 Illustrated parts catalog
Spare part number
Description
681800-211
Keyboard for use in Hungary, black
681800-251
Keyboard for use in Russia, black
681800-261
Keyboard for use in Bulgaria, black
681800-271
Keyboard for use Romania, black
681800-281
Keyboard for use Thailand, black
681800-291
Keyboard for use in Japan, black
681800-A41
Keyboard for use in Europe, black
681800-AB1
Keyboard for use in Taiwan, black
681800-AD1
Keyboard for use in Korea, black
681800-B31
Keyboard for International use, black
681800-BA1
Keyboard for use in the Adriatics, black
681800-BB1
Keyboard for use in Israel, black
681800-BG1
Keyboard for use in Switzerland, black
681800-DB1
Keyboard for use in Canada, black
681800-DH1
Keyboard for use in the Netherlands, black
681800-FL1
Keyboard for use in the Adriatics, black
681802-001
Display back cover for use in Ruby Red computer models
681803-001
Display back cover for use in Winter Blue computer models
681804-001
Display back cover for use in computer Sparkling Black computer models
681805-001
Base enclosure
681806-001
Display Bezel
681808-001
Display cable
681811-001
Display hinge covers
681812-001
Display bracket (with hinges)
681813-001
Wireless antenna (includes wireless antenna transceivers and cable)
681814-001
Blu-ray ROM DVD±R/RW Super Multi Double-Layer Drive
681815-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
681816-001
Service Door (included in Plastics kit)
681817-001
39.6 cm (15.6-in) high-definition, BrightView LED display panel
681819-001
Display screw kit
681820-001
Screw kit
681821-001
Speaker assembly (includes cable)
681823-001
Top cover for use in Ruby Red computer models
681824-001
Top cover for use in Winter Blue computer models
Sequential part number listing
23
24
Spare part number
Description
681825-001
Top cover for use in Sparkling Black computer models
682742-001
Optical drive cable
682744-001
Power connector
682745-001
Hard drive hardware kit (includes hard drive cable, hard drive bumpers, and hard drive bracket and
screws)
683547-001
USB board (includes cable)
683548-001
TouchPad button board
683549-001
Power button board
683843-001
PCH heat sink
684061-001
TouchPad LED board
Chapter 3 Illustrated parts catalog
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Flat-bladed screwdriver
●
Magnetic screwdriver
●
Phillips P0 and P1 screwdrivers
Service considerations
The following sections include some of the considerations that you must keep in mind during
disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts.
Use care when handling the plastic parts. Apply pressure only at the points designated in
the maintenance instructions.
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to
unseat or seat the cables during removal and insertion. Handle cables by the connector whenever
possible. In all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in
such a way that they cannot be caught or snagged by parts being removed or replaced. Handle flex
cables with extreme care; these cables tear easily.
Preliminary replacement requirements
25
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to
the computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether
the computer is off or in Hibernation, turn the computer on, and then shut it down through
the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and
be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing an internal hard drive to products that have magnetic fields, such as monitors
or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some
protection, but in many cases, ESD contains enough power to alter device parameters or melt
silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Before touching an electronic component, discharge static electricity by using the guidelines
described in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by
different activities.
CAUTION: A product can be degraded by as little as 700 V.
26
Chapter 4 Removal and replacement procedures
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Preliminary replacement requirements
27
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or
packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or
nonconductive foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials
are selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate
electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
28
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded
tools and equipment.
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of staticsafe materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids
and Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Chapter 4 Removal and replacement procedures
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible
straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper
ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug
connectors, use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one
megohm resistance between the operator and ground. To be effective, the conductive must be
worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
Antistatic plastics
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 63 screws that must be removed, replaced, or loosened when servicing
the computer. Make special note of each screw and screw lock size and location during removal
and replacement.
Component replacement procedures
29
Service label
When ordering parts or requesting information, provide the computer serial number and model
number provided on the service label.
Item
Description
Function
(1)
Product name
The name affixed to the front of the computer.
(2)
Serial number (s/n)
This is an alphanumeric identifier that is unique to
each product.
(3)
Part number/Product number (p/n)
This number provides specific information about
the product's hardware components. The part
number helps a service technician to determine
what components and parts are needed.
(4)
Warranty period
This number describes the duration of the warranty
period for the computer.
(5)
Model description (select models only)
This is the alphanumeric identifier needed to locate
documents, drivers, and support for the computer.
Computer feet
30
Description
Spare part number
Rubber feet kit
680563-001
Chapter 4 Removal and replacement procedures
The computer feet are adhesive-backed rubber pads. There are 4 rubber feet that attach to
the base enclosure in the locations illustrated below.
Component replacement procedures
31
Battery
Description
Spare part number
6-cell, 55-Whr, 2.55-Ah Li-ion battery
593554-001
6-cell, 47-Whr, 2.20-Ah Li-ion battery
593553-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the battery:
1.
Slide the battery release latch (1) to release the battery.
2.
Pivot the front edge of the battery (2) up and back.
3.
Remove the battery (3) from the computer.
To insert the battery:
32
1.
Align the tabs on the rear edge of the battery (1) with the notches on the rear edge of the battery
bay.
2.
Pivot the front edge of the battery (2) down into the battery bay until it is seated. (The battery
release latch will automatically lock into place.)
Chapter 4 Removal and replacement procedures
Service door
Description
Spare part number
Plastics Kit (contains the service door)
681816-001
Before removing the service door, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
Remove the service door:
1.
Using a small Phillips screwdriver, loosen the service door capture screw (1).
2.
Slide the service door (2) forward slightly and lift the front right corner (3) to tilt the service door.
3.
Remove the service door (4) at an angle.
Reverse this procedure to replace the service door.
Component replacement procedures
33
Optical drive
NOTE:
The optical drive spare part kit includes a bezel and bracket.
Description
Spare part number
Blu-ray ROM DVD±R/RW Super Multi Double-Layer Drive
681814-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
681815-001
Optical drive cable kit
682742-001
Before removing the optical drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
Remove the optical drive:
34
1.
Using a small Phillips screwdriver, remove the PM 2.5 x 6.5 screw (1) that secures the ODD to
the computer.
2.
Insert a screwdriver or other narrow tool through the release access hole (2) in the bottom of the
computer. Push the rear of the ODD until it is released.
Chapter 4 Removal and replacement procedures
3.
Pull the ODD (3) out from the front until the ODD is completely removed from the computer.
4.
Remove the 2 PM 2.0 x 3.0 screws (1) that secure the ODD bracket to the ODD and then
remove the bracket (2) from the ODD.
5.
Insert a straightened paper clip (1) into the release access opening in the bezel.
Component replacement procedures
35
6.
Press the release tab (2) and remove the bezel from the tab side (3).
7.
Remove the bezel (4) from the ODD.
Reverse this procedure to reassemble and install the optical drive.
Hard drive
NOTE: If your replacement hard drive was shipped without an operating system installed, you will
need to install it using the system recovery discs. (see Installing a hard drive without an operating
system on page 38).
If your replacement hard drive shipped with an operating system (image) installed, system recovery
discs are not required for setup. (see Installing a hard drive with an operating system on page 38)
NOTE: The hard drive spare part kit does not include the hard drive cable, hard drive bumpers, or
hard drive bracket and screws.
Description
Spare part number
Supports the following 9.50 mm, 6.35 cm (2.50 in) SATA hard drives:
1 TB, 5400 rpm
676521-001
750 GB, 7200 rpm
633252-001
750 GB, 5400 rpm
634250-001
640 GB, 5400 rpm
669300-001
500 GB, 7200 rpm
634925-001
500 GB, 5400 rpm
669299-001
320 GB, 7200 rpm
641672-001
320 GB, 5400 rpm
622643-001
Supports the following 7.00 mm, 6.35 cm (2.50 in) SATA hard drives:
320 GB, 7200 rpm
36
Chapter 4 Removal and replacement procedures
634862-001
Description
Spare part number
320 GB, 5400 rpm
645193-001
Hard drive hardware kit (includes hard drive cable, hard drive bumpers, and hard drive bracket and
screws)
682745-001
Before removing the hard drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
Remove the hard drive:
1.
Disconnect the hard drive cable (1) from the computer.
2.
Lift the hard drive (2) to remove.
3.
Disconnect the hard drive cable (1). Remove the front bumper (2) and back bumper (3).
Component replacement procedures
37
4.
Remove the 4 PM 3.0 x 3.5 screws (4), and then remove the bracket (5) from the hard drive.
Replacing the hard drive
Reverse this procedure to reassemble and install the hard drive.
Installing a hard drive with an operating system
If your hard drive shipped with an operating system (image) installed, system recovery discs are not
required for setup. Turn on the computer and allow the initial setup process to set up the operating
system completely.
IMPORTANT: Do not turn off the computer during the initial setup process. Allow the setup process
to complete to ensure that everything that is necessary to operate the computer is installed properly.
After the setup has been completed, reinstall any applications and restore any data that you backed
up.
If you need further assistance, call 1-800-474-6836 (1 800-HP Invent).
Installing a hard drive without an operating system
NOTE: If your hard drive was shipped without an operating system installed, you will need to
reinstall it using the system recovery discs. To install the operating system, refer to the instructions
included with your system recovery discs or that are available from the support site
(http://www.hp.com/go/contactHP).
IMPORTANT: Do not turn off the computer during the initial setup process. Allow the system
recovery process to complete to ensure that everything that is necessary to operate the computer is
installed properly.
The system recovery process takes approximately 3 hours to complete. When the system recovery is
complete, the computer reboots and the Setup screen displays. After the operating system has been
installed, reinstall any applications and restore any data that you backed up.
After the setup has been completed, reinstall any applications and restore any data that you backed
up.
If you need further assistance, call 1-800-474-6836 (1 800-HP Invent).
38
Chapter 4 Removal and replacement procedures
Memory module
WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power
cord and remove all batteries before installing a memory module.
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginning
any procedure, ensure that you are discharged of static electricity by touching a grounded metal
object.
NOTE: To use a dual-channel configuration with a second memory module, be sure that both
memory modules are identical.
Description
Spare part number
4 GB (PC3, 12800, 1600 MHz)
641369-001
2 GB (PC3, 12800, 1600 MHz)
652972-001
Before removing a memory module, follow these steps:
CAUTION: To prevent information loss or an unresponsive system:
Shut down the computer before adding or replacing memory modules. Do not remove a memory
module while the computer is on, in the Sleep state, or in Hibernation.
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
To add or replace a memory module:
1.
Spread the retaining clips (1) on each side of the memory module slot to release the memory
module. (The memory module tilts up.)
Component replacement procedures
39
2.
Remove the memory module (2) by pulling it away from the slot at an angle.
CAUTION: To prevent damage to the memory module, hold the memory module by the edges
only. Do not touch the components on the memory module.
CAUTION: To protect a memory module after removal, place it in an electrostatic-safe
container.
40
3.
Align the notched edge (1) of the memory module with the tab in the memory module slot.
4.
With the memory module at a 45-degree angle from the surface of the memory module
compartment, press the module into the memory module slot (2) until it is seated.
Chapter 4 Removal and replacement procedures
5.
Gently press the memory module (3) down, applying pressure to both the left and right edges of
the module, until the retention clips snap into place.
Component replacement procedures
41
WLAN module
Description
Spare part number
Atheros 9485GN 802.11b/g/n 1×1 WiFi Adapter and 3012 Bluetooth 4.0 Combo Adapter (select
models only)
655795-001
Atheros HB125 802.11b/g/n 1×1 WiFi Adapter (select models only)
675794-001
Broadcom 4313GN 802.11b/g/n 1×1 WiFi Adapter and 20702 Bluetooth 4.0+HS Combo Adapter
657325-001
Intel Centrino Wireless-N 2230 802.11b/g/n 2×2 WiFi and Bluetooth Combo Adapter
670290-001
Ralink RT5390BC8 802.11b/g/n 1×1 WiFi and Bluetooth 3.0+HS Combo Adapter
656120-001
Ralink RT5390F 802.11b/g/n 1×1 WiFi Adapter
670691-001
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless
module authorized for use in the computer by the governmental agency that regulates wireless
devices in your country or region. If you replace the module and then receive a warning message,
remove the module to restore device functionality, and then contact technical support.
Before removing the WLAN module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
Remove the WLAN module:
1.
Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
NOTE: The 1/black WLAN antenna cable is connected to the WLAN module 1/Main terminal.
The 2/gray WLAN antenna cable is connected to the WLAN module 2/Aux terminal.
2.
42
Remove the PM 2.0×4.0 screw (2) that secures the WLAN module to the system board. (The
WLAN module tilts up.)
Chapter 4 Removal and replacement procedures
3.
Remove the WLAN module by pulling the module away from the slot at an angle (3).
NOTE: The WLAN module is designed with a notch to prevent incorrect installation into
the WLAN module socket.
Reverse this procedure to install the WLAN module.
Component replacement procedures
43
Keyboard
NOTE:
The keyboard spare part kit includes a keyboard cable.
Description
Spare part number
Keyboard, Black
●
For use in the United States, Black
681800-001
●
For use in the United Kingdom, Black
681800-031
●
For use in Germany, Black
681800-041
●
For use in France, Black
681800-051
●
For use in Italy, Black
681800-061
●
For use in Spain, Black
681800-071
●
For use in Portugal, Black
681800-131
●
For use in Turkey, Black
681800-141
●
For use in Greece, Black
681800-151
●
For use in Saudi Arabia, Black
681800-171
●
For use in Hungary, Black
681800-211
●
For use in Russia, Black
681800-251
●
For use in Europe, Black
681800-A41
●
For International use, Black
681800-B31
●
For use in the Adriatics, Black
681800-BA1
●
For use in Israel, Black
681800-BB1
●
For use in Switzerland, Black
681800-BG1
●
For use in the Netherlands, Black
681800-DH1
●
For use in Bulgaria, Black
681800-261
●
For use in Romania, Black
681800-271
●
For use in Thailand, Black
681800-281
●
For use in Japan, Black
681800-291
●
For use in Taiwan, Black
681800-AB1
●
For use in Korea, Black
681800-AD1
●
For use in the Adriatics, Black
681800-FL1
●
For use in Canada, Black
681800-DB1
Before removing the keyboard, follow these steps:
44
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
Chapter 4 Removal and replacement procedures
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the hard drive (see Hard drive on page 36)
Remove the keyboard:
1.
Remove the PM 2.5 × 6.5 screw that secures the keyboard to the computer.
2.
Rest the computer on its left side.
3.
Open the computer.
Component replacement procedures
45
46
4.
Using a thin, non-conductive tool, press on the back of the keyboard through the release access
hole until the keyboard disengages from the computer.
5.
Turn the computer right-side up with the front toward you.
6.
Lift the rear edge of the keyboard (1), and then swing the keyboard (2) up and forward until it
rests upside down on the palm rest.
Chapter 4 Removal and replacement procedures
7.
Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and
then disconnect the keyboard cable (2) from the system board.
8.
Remove the keyboard.
Reverse this procedure to install the keyboard.
Component replacement procedures
47
Top cover
NOTE:
The top cover spare part kit includes the TouchPad.
Description
Spare part number
Ruby Red
681823-001
Sparkling Black
681825-001
Winter Blue
681824-001
Before removing the top cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
When replacing the top cover, be sure that the following components are removed from the defective
top cover and installed on the replacement top cover:
48
●
Power button board and cable (see Power button board on page 52).
●
TouchPad button board and cable (see TouchPad button board on page 54).
●
TouchPad LED board and cable (see TouchPad LED board on page 55).
●
Speakers and cable ( see Speakers on page 51).
Chapter 4 Removal and replacement procedures
Remove the top cover:
1.
Disconnect these cables from the system board:
(1) Power button board ZIF cable
(2) Speaker cable
(3) TouchPad button board ZIF cable
2.
Remove the following screws under the keyboard:
(1) Five PM 2.5 x 4.0
(2) One PM 2.5 x 6.5
NOTE: This screw (2) also secures the speaker underneath the top cover.
3.
Close the computer.
4.
Turn the computer upside down, with the front toward you.
Component replacement procedures
49
5.
Remove the following Nine PM 2.5 x 6.5 screws that secure the top cover to the computer.
6.
Turn the computer right-side up, with the front toward you.
7.
Open the computer.
8.
Lift the front edge of the top cover (1) until the left and right sides disengage from
the base enclosure.
9.
Remove the top cover (2).
Reverse this procedure to install the top cover.
50
Chapter 4 Removal and replacement procedures
Speakers
Description
Spare part number
Speaker Kit (includes left and right speakers and cable)
681821-001
Before removing the speakers, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
Remove the speakers:
1.
There are two clips that hold the left speaker in place (1).
NOTE: A previously removed top cover screw also secures the right speaker in place.
2.
Rotate and lift the left speaker from the top cover (2). Release the speaker cable from the clips
built into the top cover.
3.
Remove one PM 2.5 x 3.5 screw (3) from the right speaker that secures it to the top cover (2).
NOTE: This screw also secures the power button board to the top cover.
Component replacement procedures
51
4.
Lift the speakers from the top cover (4).
Reverse this procedure to install the speakers.
Power button board
Description
Spare part number
Power button board
683549–001
Before removing the power button board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
10. Remove the speakers (see Speakers on page 51).
52
Chapter 4 Removal and replacement procedures
Remove the power button board:
1.
Turn the top cover upside down, with the front toward you.
NOTE: The power button board is secured by a screw that was previously removed when
releasing the speaker.
2.
Release the tape securing the power button board cable and remove the power button board
and cable.
Reverse this procedure to install the power button board.
Component replacement procedures
53
TouchPad button board
Description
Spare part number
TouchPad button board (includes cable)
683548-001
Before removing the TouchPad button board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
Remove the TouchPad button board and cable:
54
1.
Turn the top cover upside down, with the front toward you.
2.
Release the ZIF connector to which the TouchPad button board cable is connected, and then
disconnect the TouchPad button board cable (1) from the back of the TouchPad.
3.
Remove the PM 2.5 x 2.5 screw (2) that secures the TouchPad button board cable to the top
cover.
4.
Lift the front edge of the TouchPad button board (3) until it is released from the clips built into
the top cover.
Chapter 4 Removal and replacement procedures
5.
Lift the TouchPad button board (4) slightly to perform the next step.
6.
Carefully invert the TouchPad button board (1).
7.
Release the ZIF connector to which the TouchPad LED board cable is connected, and then
disconnect the TouchPad LED board cable (2) from the TouchPad button board.
8.
Lift the TouchPad button board away from the top cover (3).
Reverse this procedure to install the TouchPad button board and cable.
TouchPad LED board
Description
Spare part number
TouchPad LED board (includes cable)
684061-001
Component replacement procedures
55
Before removing the TouchPad LED board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
10. Remove the TouchPad button board (see TouchPad button board on page 54).
Remove the TouchPad LED board and cable:
1.
Turn the top cover upside down, with the front toward you.
2.
Apply slight pressure to the retaining clips (1) of the top cover.
3.
Lift the TouchPad LED board on the right front corner (2) up and away from the top cover.
4.
Remove the TouchPad LED board and cable.
Reverse this procedure to install the TouchPad LED board and cable.
56
Chapter 4 Removal and replacement procedures
Display assembly
Description
Spare part number
Display back cover:
●
Ruby Red
681802-001
●
Sparkling Black
681804-001
●
Winter Blue
681803-001
Bezel
681806-001
Webcam/microphone module
680577-001
Hinge covers
681811-001
Display panel
681817-001
Display hinges.
681812-001
Display cable kit (includes webcam/microphone module cable)
681808-001
Antenna kit (includes the wireless antenna cables and transceivers).
681813-001
Before removing the display assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
Remove the display assembly:
1.
Disconnect the display panel cable (1) from the system board.
Component replacement procedures
57
2.
Release the wireless antenna cables (2) from the clips and the opening in the base enclosure.
NOTE: It may be necessary to release the USB board ZIF cable to remove the wireless
antenna cables.
CAUTION: Support the display assembly when removing the following screws. Failure to
support the display assembly can result in damage to the display assembly and other
computer components.
58
3.
Remove the four PM 2.5 × 6.0 screws (1) that secure the display assembly to the computer.
4.
Remove the display assembly by lifting straight up (2).
Chapter 4 Removal and replacement procedures
5.
6.
If it is necessary to replace the display bezel or any of the display assembly sub-components:
a.
Remove the plastic screw covers (1) and the two PM 2.5 × 3.5 screws (2) that secure
the display bezel to the display assembly.
b.
Flex the inside edges of the top edge (1), the left and right sides (2), and the bottom
edge (3) of the display bezel until the bezel disengages from the display enclosure.
c.
Remove the display bezel (4).
If it is necessary to replace the webcam/microphone module:
a.
Detach and release the webcam/microphone module (1) as far as the webcam/microphone
module cable allows. (The webcam/microphone module is attached to the display
enclosure with double-sided tape.)
b.
Disconnect the webcam/microphone cable (2) from the webcam/microphone module.
Component replacement procedures
59
c.
7.
If it is necessary to replace the display panel:
a.
60
Remove the webcam/microphone module.
Remove the six PM 2.5 × 6.0 screws that secure the display panel to the display enclosure.
Chapter 4 Removal and replacement procedures
b.
The hinge covers are held in place by two of the same screws as the display hinges. Using
a small tool to pry, remove the hinge covers.
c.
Lift the top edge of the display enclosure, (1) and then swing it up and forward until it is
perpendicular to the display panel.
d.
Release the adhesive strip (2) that secures the display panel cable to the display panel,
and then disconnect the display panel cable (3) from the display panel.
e.
Remove the display panel.
Component replacement procedures
61
8.
9.
62
If it is necessary to replace the display hinges:
a.
Remove the four PM 2.0 × 3.0 screws (1) that secure the display hinges to
the display panel.
b.
Remove the display hinges (2). The display hinges include the display hinges and brackets
If it is necessary to replace the display panel cable:
a.
Release the tabs (1) built into the display enclosure shielding that secure the display panel
cable to the display enclosure.
b.
Release the display panel cable from the clips (2) built into the display enclosure.
c.
Remove the display panel cable. The display panel cable includes the webcam/microphone
module cable and is available in the Display Cable Kit.
Chapter 4 Removal and replacement procedures
10. If it is necessary to replace the wireless antenna cables and transceivers:
a.
Release the wireless antenna cables from the clips (1) built into the display enclosure.
b.
Release the wireless antenna transceivers (2) from the display enclosure. (The wireless
antenna transceivers are attached to the display enclosure with double-sided tape.)
c.
Remove the wireless antenna cables and transceivers.
Reverse this procedure to reassemble and install the display assembly.
Optical drive cable
Description
Spare part number
Optical drive cable
682742-001
Before removing the optical drive cable, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
Component replacement procedures
63
9.
Remove the top cover (see Top cover on page 48).
10. Remove the system board (see System board on page 66).
Remove the optical drive cable:
1.
Release the optical drive cable from the clips built into the base enclosure.
2.
Release the optical drive connector from the base enclosure by prying the clips (1) that secure
the optical drive connector to the base enclosure.
3.
Remove the optical drive cable from the base enclosure (2).
Reverse this procedure to install the optical drive cable.
USB board
Description
Spare part number
USB board (includes cable)
683547-001
Before removing the USB board, follow these steps:
64
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
Chapter 4 Removal and replacement procedures
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
Remove the USB board:
1.
If not released already, release the ZIF connector (1) to which the USB board cable is
connected, and then disconnect the USB board cable from the system board.
2.
Pry the clip (2) that secures the USB board to the base enclosure.
3.
Remove the USB board and cable by lifting straight up (3).
Reverse this procedure to install the USB board.
Power connector
Description
Spare part number
Power connector (includes cable)
682744-001
Before removing the power connector cable, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
Component replacement procedures
65
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
Remove the power connector cable:
1.
Disconnect the power connector cable (1) from the system board.
2.
Remove the power connector from the the base enclosure (2).
Reverse this procedure to install the power connector.
System board
Description
Spare part number
For use only with computer models equipped with HM76 UMA video memory
680568-001
For use only with computer models equipped with 2048 MB of dedicated discrete video memory
680570-001
For use only with computer models equipped with 1024 MB of dedicated discrete video memory
680569-001
System board thermal pad kit (includes replacement thermal material)
680571-001
Before removing the system board, follow these steps:
66
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
Chapter 4 Removal and replacement procedures
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
When replacing the system board, be sure that the following components are removed from
the defective system board and installed on the replacement system board:
●
Memory module (see Memory module on page 39)
●
RTC battery (see RTC battery on page 69)
●
Fan and heat sink (see Fan and heat sink on page 70)
●
PCH heat sink (see PCH heat sink on page 73)
●
Processor (see Processor on page 74)
Remove the system board:
1.
Disconnect the following cables from the system board:
(1) Display panel cable
(2) Optical drive cable
(3) USB board cable
(4) Power connector cable
2.
Remove the PM 2.5 × 4.5 screw (1) that secures the system board to the base enclosure.
3.
Lift the right side of the system board (2) until it rests at an angle.
Component replacement procedures
67
4.
Remove the system board (3) by sliding it up and to the right at an angle.
Reverse this procedure to install the system board.
68
Chapter 4 Removal and replacement procedures
RTC battery
Description
Spare part number
RTC battery (includes cable and double-sided tape)
637193-001
Before removing the RTC battery, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
10. Remove the system board (see System board on page 66).
Remove the RTC battery:
1.
Turn the system board upside down, with the front toward you.
2.
Disconnect the RTC battery cable (1) from the system board.
3.
Remove the RTC battery (2) from the system board. (The RTC battery is attached to the system
board with double-sided tape.)
Reverse this procedure to install the RTC battery.
Component replacement procedures
69
Fan and heat sink
NOTE:
The fan and heat sink spare part kits include replacement thermal material.
Description
Spare part number
Fan
680551-001
Heat sink for use only with computer models equipped with UMA video memory
680549-001
Heat sink for use only with computer models equipped with Discrete video memory
680550-001
NOTE: To properly ventilate the computer, allow at least 7.6 cm (3 in) of clearance on the left side
of the computer. The computer uses an electric fan for ventilation. The fan is controlled by a
temperature sensor and is designed to turn on automatically when high temperature conditions exist.
These conditions are affected by high external temperatures, system power consumption, power
management/battery conservation configurations, battery fast charging, and software requirements.
Exhaust air is displaced through the ventilation grill located on the left side of the computer.
Before removing the fan and heat sink, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
10. Remove the system board (see System board on page 66).
Remove the fan and heat sink:
1.
Turn the system board upside down, with the front toward you.
2.
Disconnect the fan cable (1) from the system board.
CAUTION: To prevent damage to heat sinks and/or processors, loosen/tighten captive screws
in sequence as numerically labeled.
NOTE: The heat sink and fan appearance and the number of screws may be different from the
heat sink and fan pictured.
3.
70
Loosen the four Phillips captive screws (2) and the three Phillips captive screws (3) that secure
the heat sink to the system board.
Chapter 4 Removal and replacement procedures
4.
Remove the fan and heat sink (4).
NOTE: Due to the adhesive quality of the thermal material located between the heat sink and
system board components, it may be necessary to move the heat sink from side to side to
detach it.
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink
and the system board components each time the heat sink is removed. Replacement
thermal material is included with the base enclosure, heat sink, processor, and system board
spare part kits.
●
Thermal paste is used on the processor (1) and the heat sink section (2) that services it
●
A thermal pad is used on the graphics subsystem chip (3) and the heat sink section (4) that
services it (only on computer models equipped with a graphics subsystem with
discrete memory)
Component replacement procedures
71
1.
If it is necessary to replace the fan, turn the fan and heat sink upside down with the fan
toward you.
2.
Remove the two PM 1.5 × 2.5 screws (1) that secure the fan to the heat sink and remove the two
clips that secure the fan to the heat sink.
3.
Remove the heat sink (2) from the fan.
Reverse this procedure to reassemble and install the fan and heat sink.
72
Chapter 4 Removal and replacement procedures
PCH heat sink
Description
Spare part number
PCH heat sink
683843-001
Before removing the PCH heat sink, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
10. Remove the system board (see System board on page 66).
Remove the PCH heat sink:
1.
Remove the two PM 2.0 x 3.0 screws (1) that secure the PCH heat sink to the system board.
Component replacement procedures
73
2.
Remove the PCH heat sink by lifting straight up (2).
NOTE: Due to the adhesive quality of the thermal material located between the heat sink and
system board components, it may be necessary to move the heat sink from side to side to
detach it.
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink
and the system board components each time the heat sink is removed. Replacement
thermal material is included with the base enclosure, heat sink, processor, and system board
spare part kits.
Reverse this procedure to install the PCH heat sink.
Processor
NOTE:
The processor spare part kit includes replacement thermal material.
Description
Spare part number
Intel Core i5-2450M 2.50 GHz (SC turbo up to 3.10 GHz) processor (1333 MHz/3.0 MB L3 cache,
dual core, 35 W)
676359-001
Intel Core i3-2350M 2.30 GHz processor (1333 MHz/3.0 MB L3 cache, dual core, 35 W)
653340-001
Intel Core i3-2330M 2.20 GHz processor (1333 MHz/3.0 MB L3 cache, dual core, 35 W)
653339-001
Intel Pentium B960 2.20 GHz processor (1333 MHz/2.0 MB L3 cache, dual core, 35 W)
664662-001
Before removing the processor, follow these steps:
74
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Chapter 4 Removal and replacement procedures
4.
Remove the battery (see Battery on page 32).
5.
Remove the service door (see Service door on page 33).
6.
Remove the optical drive (see Optical drive on page 34).
7.
Remove the hard drive (see Hard drive on page 36)
8.
Remove the keyboard (see Keyboard on page 44).
9.
Remove the top cover (see Top cover on page 48).
10. Remove the system board (see System board on page 66).
11. Remove the heat sink (see Fan and heat sink on page 70).
Remove the processor:
1.
Use a flat-bladed screw driver (1) to turn the processor locking screw one-half turn
counterclockwise, until you hear a click.
2.
Lift the processor (2) straight up, and remove it.
NOTE: The gold triangle on the processor (3) must be aligned with the triangle icon embossed
on the processor socket when you install the processor.
Reverse this procedure to install the processor.
Component replacement procedures
75
5
Specifications
Computer specifications
Dimensions
Depth
24.5 cm (9.6 in)
Width
37.4 cm (14.7 in)
Height (front to rear)
3.1 to 3.6 cm (1.2 to 1.4 in)
Weight (lowest weight configuration)
< 2.5 kg (5.5 lbs)
Input power
Operating voltage
18.5 V dc @ 3.5 A - 65W
Operating current
3.5 A
Temperature
Operating
5°C to 35°C (41°F to 95°F)
Nonoperating
-20°C to 60°C (-4°F to 140°F)
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m (-50 ft to 10,000 ft)
Nonoperating
-15 m to 12,192 m (-50 ft to 40,000 ft)
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within
this range of temperatures.
76
Chapter 5 Specifications
39.6-cm (15.6-in) display specifications
Dimensions
Height
21.0 cm (8.27 in)
Width
35.9 cm (14.1 in)
Diagonal
39.6 cm (15.6)
Number of colors
Up to 16.8 million
Contrast ratio
300:1 (typical)
Brightness
200 cd/m² (typical)
Pixel resolution
Pitch
0.259 × 0.259 mm
Format
1280 × 800; HD: 1366 × 768
Configuration
RGB vertical stripe
Backlight
LED
Character display
80 × 25
Total power consumption
4.0 W
Viewing angle
±40° horizontal, +120/-40° vertical (typical)
39.6-cm (15.6-in) display specifications
77
Hard drive specifications
1 TB*
750 GB*
640 GB*
500 GB*
320 GB*
Height
9.5 mm
9.5 mm
9.5 mm
9.5 mm
9.5 mm and 7.0
mm
Width
70 mm
70 mm
70 mm
70 mm
70 mm
Weight
107g max
107g max
107g max
107g max
107g max
Interface type
SATA
SATA
SATA
SATA
SATA
Transfer rate
300 MB/sec
300 MB/sec
300 MB/sec
300 MB/sec
300 MB/sec
Security
ATA security
ATA security
ATA security
ATA security
ATA security
Dimensions
Seek times (typical read, including setting)
Single track
1.5 ms
1.0 ms
1.0 ms
1.5 ms
2.0 ms
Average
11.0 ms
14.0 ms
14.0 ms
12.0 ms
12.0 ms
Maximum
22.0 ms
24.0 ms
22.0 ms
22.0 ms
22.0 ms
Logical blocks
312,215,808
1,250,263,728
976,773,168
625,142,448
488,397,168
Disc rotational speed
5400 rpm
5400 and 7200
rpm
5400 rpm
5400 and 7200
rpm
5400 and 7200
rpm
Operating temperature
5°C to 55°C (41°F to 131°F)
*Hard drive storage capacity
When referring to hard drive storage capacity:
●
1 TB = 1 trillion bytes
●
1 GB = 1 billion bytes
Actual accessible capacity is less. Actual drive specifications may differ slightly.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
78
Chapter 5 Specifications
DVD±RW and CD-RW SuperMulti Double-Layer Combo
Drive specifications
Applicable disc
Read
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED
MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD
(Photo-CD, CD-EXTRA, Portfolio, CD-R, CD-RW), CD-R, CD-RW, DVDROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW, DVD+R, DVD
+RW, DVD-RAM
Write
CD-R and CD-RW, DVD+R, DVD+RW, DVD-R, DVD-RW, DVD-RAM
Random access time
DVD
< 230 ms
CD
< 175 ms
Cache buffer
2 MB
Data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD-ROM
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
Transfer mode
Multiword DMA Mode
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive specifications
79
Blu-ray Disc ROM and DVD±R/RW SuperMulti DoubleLayer Drive specifications
Applicable disc
Read
BD-ROM, BD-ROM-DL, BD-R, BD-R-DL, BD-RE, BD-RE-DL, DVD-ROM,
DVD+R, DVD+R-DL, DVD+RW, DVD-R, DVD-R-DL, DVD-RW, DVD-RAM
(Ver.2), CD-DA, CD-ROM (mode 1 and mode 2), CD-ROM XA (mode 2,
form 1 and form 2), Photo CD (single and multiple sessions), CD Extra,
CD-R, CD-RW, and CD-TEXT
Write
DVD-RAM (Ver.2), DVD+R, DVD-R, CD-R, and CD-ROM
Random access time
BD
< 230 ms
DVD
< 180 ms
CD
< 180 ms
Cache buffer
4.5 MB
Data transfer rate
80
24X CD-ROM
3,600 KB/sec
8X DVD-ROM
10,800 KB/sec
4X BD
18,000 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
1X BD-ROM
4,500 KB/sec
1X BD-R read
4,500 KB/sec
1X BD-RE read
4,500 KB/sec
Transfer mode
Multiword DMA Mode
Chapter 5 Specifications
6
Setup Utility (BIOS)
Setup Utility, or Basic Input/Output System (BIOS), controls communication between all the input and
output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Setup
Utility includes settings for the types of peripherals installed, the startup sequence of the computer,
and the amount of system and extended memory.
CAUTION: Use extreme care when making changes in Setup Utility. Errors can prevent the
computer from operating properly.
Starting Setup Utility
NOTE:
▲
The fingerprint reader (select models only) cannot be used to access Setup Utility.
Turn on or restart the computer. While the “Press the ESC key for Startup Menu” message is
displayed in the lower-left corner of the screen, press esc. When the Startup Menu is displayed,
press f10.
Using Setup Utility
Changing the language of Setup Utility
1.
Start Setup Utility.
2.
Use the arrow keys to select System Configuration > Language, and then press enter.
3.
Use the arrow keys to select a language, and then press enter.
4.
When a confirmation prompt with your language selected is displayed, press enter.
5.
To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
Your change takes effect immediately.
Navigating and selecting in Setup Utility
Because Setup Utility is not Windows based, it does not support the TouchPad. Navigation and
selection are by keystroke.
●
To choose a menu or a menu item, use the arrow keys.
●
To choose an item in a list or to toggle a field—for example an Enable/Disable field—use either
the arrow keys or f5 and f6.
●
To select an item, press enter.
●
To close a text box or return to the menu display, press esc.
●
To display additional navigation and selection information while Setup Utility is open, press f1.
Starting Setup Utility
81
Displaying system information
1.
Start Setup Utility.
2.
Select the Main menu. System information such as the system time and date, and identification
information about the computer is displayed.
3.
To exit Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter.
Restoring factory default settings in Setup Utility
1.
Start Setup Utility.
2.
Use the arrow keys to select Exit > Load Setup Defaults, and then press enter.
3.
When the Setup Confirmation is displayed, press enter.
4.
To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
The Setup Utility factory settings take effect when the computer restarts.
NOTE: Your password, security, and language settings are not changed when you restore the
factory settings.
Exiting Setup Utility
●
To exit Setup Utility and save your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Saving Changes, and then press enter.
●
To exit Setup Utility without saving your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Discarding Changes, and then press enter.
82
Chapter 6 Setup Utility (BIOS)
Updating the BIOS
Updated versions of the BIOS may be available on the HP Web site.
Most BIOS updates on the HP Web site are packaged in compressed files called SoftPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding
installing and troubleshooting the file.
Determining the BIOS version
To determine whether available BIOS updates contain later BIOS versions than those currently
installed on the computer, you need to know the version of the system BIOS currently installed.
BIOS version information (also known as ROM date and System BIOS) can be displayed by pressing
fn+esc (if you are already in Windows) or by using Setup Utility.
1.
Start Setup Utility.
2.
If the system information is not displayed, use the arrow keys to select the Main menu.
BIOS and other system information is displayed.
3.
To exit Setup Utility, use the arrow keys to select Exit > Exit Discarding Changes, and then
press enter.
Downloading a BIOS update
CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download
and install a BIOS update only when the computer is connected to reliable external power using the
AC adapter. Do not download or install a BIOS update while the computer is running on battery
power, docked in an optional docking device, or connected to an optional power source. During the
download and installation, follow these instructions:
Do not disconnect power from the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep or Hibernation.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
1.
Access the page on the HP Web site that provides software for your computer:
Select Start > Help and Support > Maintain.
2.
Follow the on-screen instructions to identify your computer and access the BIOS update you
want to download.
3.
At the download area, follow these steps:
a.
Identify the BIOS update that is later than the BIOS version currently installed on your
computer. Make a note of the date, name, or other identifier. You may need this information
to locate the update later, after it has been downloaded to your hard drive.
b.
Follow the on-screen instructions to download your selection to the hard drive.
Make a note of the path to the location on your hard drive where the BIOS update is
downloaded. You will need to access this path when you are ready to install the update.
NOTE: If you connect your computer to a network, consult the network administrator before
installing any software updates, especially system BIOS updates.
Updating the BIOS
83
BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the
download is complete. If no instructions are displayed, follow these steps:
1.
Windows-7—Open Windows Explorer by selecting Start > Computer.
2.
Double-click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3.
Using the hard drive path you recorded earlier, open the folder on your hard drive that contains
the update.
4.
Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5.
Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the
downloaded file from your hard drive.
84
Chapter 6 Setup Utility (BIOS)
7
Backing up, restoring, and recovering
Your computer includes tools provided by the operating system and HP to help you safeguard your
information and retrieve it if ever needed.
Creating backups
1.
Use HP Recovery Manager to create recovery media immediately after you set up the working
computer.
2.
As you add hardware and software programs, create system restore points.
3.
As you add photos, video, music, and other personal files, create a backup of your system and
personal information.
Creating recovery media to recover the original system
After you successfully set up the computer, you should create recovery discs or a recovery flash drive
using HP Recovery Manager. You will need these recovery discs or recovery flash drive to perform a
system recovery should the hard drive become corrupted. A system recovery reinstalls the original
operating system, and then configures the settings for the default programs.
What you need to know
●
Only one set of recovery media can be created. Handle these recovery tools carefully, and keep
them in a safe place.
●
HP Recovery Manager examines the computer and determines the required storage capacity for
the flash drive or the number of blank DVD discs that will be required.
Use DVD-R, DVD+R, DVD-R DL, DVD+R DL discs or a flash drive. Do not use rewriteable discs
such as CD±RW, DVD±RW, double-layer DVD±RW, and BD-RE (rewritable Blu-ray) discs; they
are not compatible with HP Recovery Manager software.
●
If your computer does not include an integrated optical drive, you can use an optional external
optical drive (purchased separately) to create recovery discs, or you can obtain recovery discs
for your computer from the HP website. If you use an external optical drive, it must be connected
directly to a USB port on the computer, not to a USB port on an external device, such as a USB
hub.
●
Be sure that the computer is connected to AC power before you begin creating the recovery
media.
●
The creation process can take up to an hour or more. Do not interrupt the creation process.
●
Store the recovery media in a safe location, separate from the computer.
●
If necessary, you can exit the program before you have finished creating the recovery media.
The next time you open HP Recovery Manager, you will be prompted to continue the process.
Creating backups
85
Creating the recovery media
1.
Select Start and type recovery in the search field. Select Recovery Manager from the list.
Allow the action to continue, if prompted.
2.
Click Recovery Media Creation.
3.
Follow the on-screen instructions to continue.
To recover, see Recovering the original system using HP Recovery Manager on page 88
Creating system restore points
A system restore point is a snapshot of certain hard drive contents saved by Windows System
Restore at a specific time. A restore point contains information such as registry settings that Windows
uses. Restoring to a previous restore point allows you to reverse changes that have been made to the
system since the restore point was created.
Restoring to an earlier system restore point does not affect data files saved or emails created since
the last restore point, but it does affect software you may have installed.
For example, if you download a photo from a digital camera and then restore the computer to the
state it was on the previous day, the photo remains on the computer.
However, if you install photo viewing software and then restore your computer to the state it was on
the previous day, the software will be uninstalled, and you won't be able to use it.
What you need to know
●
If you restore to a restore point and then change your mind, you can undo the restoration.
●
You should create system restore points:
●
◦
Before you add or change software or hardware
◦
Periodically, whenever the computer is running normally
System Restore also saves shadow copies of files that have been changed since the last restore
point was created. For more information about using shadow copies to restore, see Help and
Support.
Creating a system restore point
1.
Select Start > Control Panel > System and Security > System.
2.
In the left pane, click System Protection.
3.
Click the System Protection tab.
4.
Click Create, and follow the on-screen instructions.
To restore, see Restoring to a previous system restore point on page 88.
Backing up system and personal information
Your computer stores information that is important to you, such as files, emails, and photos, and you
will want to keep that information even if you download a virus or the system stops working properly.
How completely you are able to recover your files depends on how recent your backup is. As you add
new software and data files, you should create backups on a regular basis.
86
Chapter 7 Backing up, restoring, and recovering
Tips for a successful backup
●
Number backup discs before inserting them into the optical drive.
●
Store personal files in the Documents, Music, Pictures, and Videos libraries, and back up these
folders periodically.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your
settings. The screen shot can be a time-saver if you have to re-enter your preferences.
To create a screen shot:
1.
Display the screen you want to save.
2.
Copy the screen image:
To copy only the active window, press alt+prt sc.
To copy the entire screen, press prt sc.
3.
Open a word-processing document or graphics editing program, and then select Edit > Paste.
The screen image is added to the document.
4.
Save and print the document.
What you need to know
●
You can back up your information to an optional external hard drive, a flash drive, a network
drive, or discs.
●
Connect the computer to AC power during backups.
●
Allow enough time for the backup. Depending on files sizes, it may take more than an hour.
●
Verify the amount of free space on your backup storage device before you back up.
●
You should back up:
◦
Before adding or changing software or hardware.
◦
Before the computer is repaired or restored.
◦
On a regular schedule to be sure you have recent copies of personal information.
◦
After you add many files—for example, if you saved videos from a birthday party.
◦
Before using antivirus software to remove a malicious program.
◦
After adding information that is hard to replace, such as pictures, videos, music, project
files, or data records.
Creating a backup using Windows Backup and Restore
Windows allows you to back up files using Windows Backup and Restore. You can select the level
you want to back up, from individual folders to drives. The backups are compressed to save space.
To back up:
1.
Select Start > Control Panel > System and Security > Backup and Restore.
2.
Follow the on-screen instructions to schedule and create a backup.
NOTE: Windows includes the User Account Control feature to improve the security of the computer.
You may be prompted for your permission or password for tasks such as installing software, running
utilities, or changing Windows settings. See Help and Support for more information.
Creating backups
87
To restore, see Restoring specific files using Windows Backup and Restore on page 88.
Restore and recovery
Restoring to a previous system restore point
Sometimes installing a software program causes your computer or Windows to behave unpredictably.
Usually uninstalling the software fixes the problems. If uninstalling does not fix the problems, you can
restore the computer to a previous system restore point (created at an earlier date and time).
To restore to a previous system restore point, when the computer was running correctly:
1.
Select Start > Control Panel > System and Security > System.
2.
In the left pane, click System Protection.
3.
Click the System Protection tab.
4.
Click System Restore, and follow the on-screen instructions.
Restoring specific files
If files are accidentally deleted from the hard disk and they can no longer be restored from the
Recycle Bin, or if files become corrupt, restoring specific files is useful. Restoring specific files is also
useful if you ever choose to recover the original system using HP Recovery Manager. You can only
restore specific files that you have backed up before.
Restoring specific files using Windows Backup and Restore
Windows allows you to restore files that were backed up using Windows Backup and Restore:
1.
Select Start > Control Panel > System and Security > Backup and Restore.
2.
Follow the on-screen instructions to restore your backup.
NOTE: Windows includes the User Account Control feature to improve the security of the computer.
You may be prompted for your permission or password for tasks such as installing software, running
utilities, or changing Windows settings. See Help and Support for more information.
Recovering the original system using HP Recovery Manager
HP Recovery Manager software allows you to repair or recover the computer to its original factory
state.
What you need to know
88
●
HP Recovery Manager recovers only software that was installed at the factory. For software not
provided with this computer, you must either download the software from the manufacturer's
website or reinstall the software from the disc provided by the manufacturer.
●
A system recovery should be used as a final attempt to correct computer issues. If you have not
already tried restore points (see Restoring to a previous system restore point on page 88) and
partial restores (see Restoring specific files on page 88), try them before using HP Recovery
Manager to recover your system.
●
A system recovery must be performed if the computer hard drive fails or if all attempts to correct
any functional computer issues fail.
Chapter 7 Backing up, restoring, and recovering
●
If the recovery media do not work, you can obtain recovery discs for your system from the HP
website.
●
The Minimized Image Recovery option is recommended for advanced users only. All hardwarerelated drivers and software are re-installed, but other software applications are not. Do not
interrupt the process until it is complete, otherwise the recovery will fail.
Recovering using HP Recovery partition (select models only)
The HP Recovery partition (select models only), allows you to restore your system without the need
for recovery discs or a recovery flash drive. This type of recovery can only be used if the hard drive is
still working.
To check for the presence of a recovery partition, select Start, right-click Computer then select
Manage > Disk Management. If the recovery partition is present, a Recovery drive is listed in the
window.
NOTE:
1.
Recovery discs have been included if your computer did not ship with a recovery partition.
Access HP Recovery Manager in either of the following ways:
●
Select Start and type recovery in the search field. Select Recovery Manager from the
list.
– or –
●
Turn on or restart the computer, and then press esc while the “Press the ESC key for
Startup Menu” message is displayed at the bottom of the screen. Then press f11 while the
“F11 (System Recovery)” message is displayed on the screen.
2.
Click System Recovery in the HP Recovery Manager window.
3.
Follow the on-screen instructions.
Recovering using the recovery media
1.
If possible, back up all personal files.
2.
Insert the first recovery disc into the optical drive on your computer or an optional external
optical drive, and then restart the computer.
– or –
Insert the recovery flash drive into a USB port on your computer, and then restart the computer.
NOTE: If the computer does not automatically restart in HP Recovery Manager, change the
computer boot order. See Changing the computer boot order on page 89.
3.
Press f9 at system bootup.
4.
Select the optical drive or the flash drive.
5.
Follow the on-screen instructions.
Changing the computer boot order
To change the boot order for recovery discs:
1.
Restart the computer.
2.
Press esc while the computer is restarting, and then press f9 for boot options.
3.
Select Internal CD/DVD ROM Drive from the boot options window.
Restore and recovery
89
To change the boot order for a recovery flash drive:
90
1.
Insert the flash drive into a USB port.
2.
Restart the computer.
3.
Press esc while the computer is restarting, and then press f9 for boot options.
4.
Select the flash drive from the boot options window.
Chapter 7 Backing up, restoring, and recovering
8
Power cord set requirements
The wide-range input feature of the computer permits it to operate from any line voltage from 100 to
120 V ac, or from 220 to 240 V ac.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries or regions must meet the requirements of the country and
region where the computer is used.
Requirements for all countries
The following requirements are applicable to all countries and regions:
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for
evaluation in the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 A and a nominal voltage rating
of 125 or 250 V ac, as required by the power system of each country or region.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320
Standard Sheet C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for all countries
91
Requirements for specific countries and regions
92
Country/region
Accredited agency
Applicable note number
Argentina
IRAM
1
Australia
SAA
1
Austria
OVE
1
Belgium
CEBEC
1
Brazil
ABNT
1
Canada
CSA
2
Chile
IMQ
1
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
India
ISI
1
Israel
SII
1
Italy
IMQ
1
Japan
JIS
3
The Netherlands
KEMA
1
New Zealand
SANZ
1
Norway
NEMKO
1
The People's Republic of China
CCC
4
Saudi Arabia
SASO
7
Singapore
PSB
1
South Africa
SABS
1
South Korea
KTL
5
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
6
Thailand
TISI
1
The United Kingdom
ASTA
1
Chapter 8 Power cord set requirements
Country/region
Accredited agency
Applicable note number
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 0.75 mm² conductor size. Power cord set fittings (appliance
coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region
where it will be used.
2.
The flexible cord must be Type SVT/SJT or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole
grounding type with a NEMA 5-15P (15 A, 125 V ac) or NEMA 6-15P (15 A, 250 V ac) configuration. CSA or C-UL
mark. UL file number must be on each element.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCTF, 3-conductor, 0.75 mm² or 1.25 mm² conductor size. The
wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V ac) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75 mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the CCC certification mark.
5.
The flexible cord must be Type H05VV-F 3-conductor, 0.75 mm² conductor size. KTL logo and individual approval
number must be on each element. Corset approval number and logo must be printed on a flag label.
6.
The flexible cord must be Type HVCTF 3-conductor, 1.25 mm² conductor size. Power cord set fittings (appliance
coupler, cable, and wall plug) must bear the BSMI certification mark.
7.
For 127 V ac, the flexible cord must be Type SVT or SJT 3-conductor, 18 AWG, with plug NEMA 5-15P (15 A, 125 V
ac), with UL and CSA or C-UL marks. For 240 V ac, the flexible cord must be Type H05VV-F 3-conductor, 0.75 mm² or
1.00 mm2 conductor size, with plug BS 1363/A with BSI or ASTA marks.
Requirements for specific countries and regions
93
9
Recycling
When a battery has reached the end of its useful life, do not dispose of the battery in general
household waste. Follow the local laws and regulations in your area for battery disposal. HP
encourages customers to recycle used electronic hardware, HP original print cartridges, and
rechargeable batteries.
For more information about recycling programs, see the HP website at www.hp.com/recycle.
94
Chapter 9 Recycling
Index
A
AC adapter
light 11
spare part numbers 20
action keys, identifying 7
antenna
locations 5
removal 63
spare part number 18, 57
audio, product description 2
audio-in (microphone) jack
identifying 10
audio-out (headphone) jack
identifying 10
B
backups 85
base enclosure, spare part
number 16
battery
removal 32
spare part numbers 16, 32
battery bay 12
battery release latch 12
bezel
spare part number 18
BIOS
determining version 83
downloading an update 83
updating 83
Blu-ray Disc ROM and DVD±R/RW
SuperMulti Double-Layer Drive
specifications 80
Blu-ray ROM DVD±R/RW Super
Multi Double-Layer Drive
precautions 26
removal 19, 34
spare part numbers 19, 34
boot order
changing 89
bottom components 12
buttons
left TouchPad 9
optical drive eject 11
power 6
right TouchPad 9
TouchPad on/off 9
buttons component 6
C
cables, service considerations 25
camera, product description 2
caps lock light, identifying 8
chipset, product description 1
components
bottom 12
button 6
display 5
keys 7
left side 10
lights 8
right side 11
speakers 6
TouchPad 9
computer feet
locations 30
spare part number 30
computer specifications 76
connector, power 11
connectors, service
considerations 25
D
default settings, restoring 82
deleted files
restoring 88
Digital media slot, identifying 10
display assembly
removal 57
spare part number 15
spare part numbers 57
Display back cover 57
display back cover, spare part
number 18
display bezel
illustrated 18
removal 59
spare part number 18, 57
Display Cable Kit, spare part
number 57
display cable, spare part number
18
display components 5
illustrated 18
spare part numbers 18
display enclosure, illustrated 18
Display hinge cover, spare part
number 18
Display Hinge Kit, spare part
number 57
display panel
illustrated 18
product description 1
removal 60
spare part number 18, 57
display panel cable
removal 62
spare part number 57
display specifications 77
drives, preventing damage 26
DVD±RW and CD-RW Super Multi
Double-Layer Combo Drive
precautions 26
removal 19, 34
spare part numbers 19, 34
DVD±RW and CD-RW SuperMulti
Double-Layer Combo Drive
specifications 79
E
electrostatic discharge 26
equipment guidelines 29
esc key, identifying 7
Ethernet, product description 2
external media cards, product
description 3
external monitor port 10
F
factory settings, restoring 82
fan
removal 70
spare part number 70
Index
95
feet
locations 30
spare part number 30
fn key, identifying 7
G
graphics, product description
grounding guidelines 26
guidelines
equipment 29
grounding 26
packaging 28
transporting 28
workstation 28
1
H
hard drive
precautions 26
product description 1
removal 36
spare part numbers 16, 19, 36
specifications 78
Hard Drive Hardware Kit, spare
part number 19, 37
Hard drive light 11
HDMI port, identifying 10
heat sink
removal 70
spare part numbers 70
heat sink assembly
spare part number 16
hinge
removal 62
spare part number 57
hinge cover
spare part number 57
HP Recovery Manager 88
I
integrated numeric keypad,
identifying 7
J
jack
audio-in (microphone) 10
audio-out (headphone) 10
jacks
network 10
RJ-45 (network) 10
96
Index
K
key components 7
keyboard
product description 3
removal 44
spare part numbers 15, 44
keys
action 7
esc 7
fn 7
integrated numeric keypad 7
num lock 7
Windows applications 7
Windows logo 7
L
latch, battery release 12
left-side components 10
light components 8
lights
AC adapter 11
caps lock 8
hard drive 11
mute 8
optical drive 11
power 8, 11
TouchPad 8, 9
webcam 5
wireless 8
M
mass storage device
precautions 26
removal 36
spare part numbers 36
mass storage devices, spare part
numbers 19
memory module
product description 1
removal 39
spare part numbers 17, 39
microphone
location 5
model name 1
mute light, identifying 8
N
network jack, identifying 10
num lock, identifying 7
O
operating system, product
description 4
optical drive
precautions 26
product description 2
removal 34
spare part numbers 17, 19, 34
specifications 79, 80
optical drive bracket, removal 35
optical drive cable
removal 63
optical drive eject button,
identifying 11
optical drive light, identifying 11
optical drive, identifying 11
original system recovery 88
P
packaging guidelines 28
PCH heat sink
removal 73
spare part number 73
plastic parts, service
considerations 25
pointing device, product
description 3
ports
external monitor 10
HDMI 10
product description 3
USB 2.0 11
USB 3.0 10
power button board
removal 52
spare part number 16, 52
power button, identifying 6
power connector
removal 65
spare part number 16
power connector, identifying 11
power cord
requirements for all countries
91
requirements for specific
countries and regions 92
set requirements 91
power cord, spare part numbers
20
power lights, identifying 8, 11
power requirements, product
description 3
processor
product description 1
removal 74
spare part numbers 16, 74
product description
audio 2
camera 2
chipset 1
display panel 1
Ethernet 2
external media cards 3
graphics 1
hard drives 1
keyboard 3
memory module 1
operating system 4
optical drive 2
pointing devices 3
ports 3
power requirements 3
processors 1
product name 1
security 3
serviceability 4
wireless 2
product name 1
R
recovering from the recovery
discs 89
recovering the original system 88
recovery 88
HP Recovery Manager 88
recovery discs 85
recovery media 85
recovery, system 88
removal/replacement
preliminaries 25
procedures 29
restore points 86
restoring the original system
creating recovery media 85
right-side components 11
RJ-45 (network) jack, identifying
10
RTC battery
removal 69
spare part number 16, 69
Rubber Feet Kit, spare part
number 30
S
security cable slot, identifying 11
security, product description 3
serial number 13
service considerations
cables 25
connectors 25
plastic parts 25
service door
removal 33
service door release latch 12
service door, identifying 12
service label 30
serviceability, product
description 4
Setup Utility
changing the language 81
displaying system information
82
exiting 82
navigating 81
restoring default settings 82
selecting 81
starting 81
slots
Digital media 10
security cable 11
speaker assembly
spare part number 16
Speaker Kit, spare part number
51
speakers
identifying 6
removal 51
spare part number 51
specifications
Blu-ray Disc ROM and DVD±R/
RW SuperMulti Double-Layer
Drive 80
computer 76
display 77
DVD±RW and CD-RW
SuperMulti Double-Layer
Combo Drive 79
hard drive 78
optical drive 79, 80
supported discs 85
system board
removal 66
spare part numbers 16, 66
system information, displaying 82
system recovery 88
system restore points 86
creating 86
T
tools required 25
top cover
removal 48
spare part number 15
spare part numbers 48
TouchPad
buttons 9
TouchPad button board
removal 54
spare part number 54
TouchPad components 9
TouchPad LED board
removal 55
spare part number 55
TouchPad light 9
TouchPad on/off button 9
TouchPad reader light 8
TouchPad zone, identifying 9
transporting guidelines 28
U
USB 2.0 ports, identifying 11
USB 3.0 ports, identifying 10
USB board
removal 64
spare part number 16
V
vents, identifying 10, 12
W
webcam light 5
webcam module, spare part
number 18
webcam, location 5
webcam/microphone module
removal 59
spare part number 57
Windows applications key,
identifying 7
Windows Backup and Restore
restoring files 88
Index
97
Windows logo key, identifying 7
wireless antenna
locations 5
removal 63
spare part number 18, 57
wireless light 8
wireless, product description 2
WLAN module
removal 42
spare part numbers 17, 42
workstation guidelines 28
98
Index
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement