Creda Contour 100 Electronic Instructions (UK) - Issue

Creda Contour 100 Electronic Instructions (UK) - Issue
 Contact Details Please note that some of the contact details on this PDF document may not be current. Please use the following details if you need to contact us: Telephone: 0844 879 3588 Email: [email protected] The Help Centre section of this website also features a wide range of information which may be of use to you and is available 24 hours a day. It includes: • Operating and installation instructions downloads • Request a repair • Where to buy our products • Literature downloads • Heating requirement calculator www.credaheating.co.uk/help‐centre A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.credaheating.co.uk
Registered No: 1313016 England
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources
Installation and Operating Instructions
Contour 100 Electronic Panel Heaters
INCMUKP7RG Issue 4
shelf
Dimensions
(millimetres)
Model(s)
Watt
A
B
CEP 500E
0.5kW
503
104
CEP 750E
0.75kW
503
104
CEP 1000E
1.0kW
671
104
CEP 1500E
1.5kW
741
104
CEP 2000E
2.0kW
911
104
150
Min.
300 Min.
A
B
536
150 Min.
Fig. 1
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
Electrical
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electrical shock, and injury to persons, including the
following:
IMPORTANT – The wall bracket supplied with the appliance
must be used.
WARNING – THIS APPLIANCE MUST BE EARTHED
The electrical installation must be carried out by a competent
electrician, and be in strict accordance with the current I.E.E.
regulations for Electrical Equipment in Buildings.
IMPORTANT – Do not use this heater in the immediate
surroundings of a bath, a shower or a swimming pool. If
the heater is installed in a room containing a bath or
shower, it must be so installed that switches and other
controls cannot be touched by a person using a bath or
shower.
Do not use outdoors.
WARNING - In order to avoid overheating, do not cover the
heater. Do not place material or garments on the heater,
or obstruct the air circulation around the heater, for
instance by curtains or pushing furniture up against the
heater, as this could cause overheating and a fire risk.
NEVER cover or obstruct in any way the heat outlet slots
at the top of the heater or the air inlet slots in the base of
the heater.
The heater carries the Warning symbol indicating
that it must not be covered.
WARNING – THE SURFACES OF THIS HEATER CAN BE HOT.
Momentary contact with any part of the heater should not
cause injury.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
The wires in this mains lead are coloured in accordance with the
following code :
GREEN AND YELLOW :EARTH
BLUE :
NEUTRAL
BROWN :
LIVE
BLACK :
PILOT WIRE
- see also ‘Pilot Wire Connection’.
The heater is fitted with a length of flexible cable type H05VV-F size
4 x 1.0mm2 for connection to the fixed wiring of the premises through
a suitable connection box positioned adjacent to the heater.
The supply circuit to the heater must incorporate a double pole isolating
switch having a contact separation of at least 3mm.
Pilot Wire Connection
The BLACK control wire is designed to carry a signal from slot in or
wall mounted Creda programmers. If, however a programmer is not
being used, the pilot wire should be isolated in accordance with the
current IEE Wiring Regulations.
IMPORTANT - DO NOT connect the BLACK pilot wire to earth. Care
should be taken with the installation of the pilot wire(s) as when
switching to background (set back) they become energised at 240V
although only at a current of less than 100mA. In every case a
suitable means of isolation must be provided for the pilot wire and
marked to indicate that two sources of supply may be present at the
heater.
Where pilot wires are installed separately from the heater final subcircuit they should be protected, double insulated and carry their
own integral earth continuity conductor.
Supplementary Earth Bonding
Note that due care and consideration must be taken when
using this heater in series with a thermal control, a
program controller, a timer or any other device that
switches on the heat automatically, since a fire risk exists
when the heater is accidentally covered or displaced.
Should Equipotential Earth Bonding be required the earthing conductor
in the supply cord is deemed to provide the supplementary bonding
connection (see Regulation 544.2.5, 17 th Edition I.E.E. Wiring
Regulations).
General
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
The heater is designed for wall mounting on the wall bracket supplied.
It should only be operated when in the upright position as shown see Fig. 1.
WARNING Servicing & Product repairs should only be
undertaken by the manufacturers approved service agent
or a similarly qualified person, using only exact
manufacturer approved spare parts.
All models are splashproof to IPX4 standard and may be used in
bathrooms, however not in the immediate vicinity of baths, showers,
water connections, wash basins or swimming pools.
Before connecting the heater check that the supply voltage is the
same as that stated on the heater.
NOTE - Lit cigarettes, candles and oil burners, combined with the
convection effect of electric heaters can cause soot deposits to
build up on the surface directly above and to the sides of the
heater. Extensive burning of candles or smoking in the operating
environment of this product can produce heavy discolouration
within a few months of use.
Wall Mounting
IMPORTANT – The wall bracket supplied with the appliance must be
used. The heater should be positioned observing the minimum
clearances
stated
around
the
heater
see
Fig. 1.
DO NOT locate the heater immediately below a fixed socket outlet or
connection box.
1.
2.
3.
4.
Remove wall mounting bracket from the back of the
heater by depressing the spring latch at the top of each
bracket - see Fig. 2.
Fix the wall bracket securely to the wall through the four
screw holes provided.
Present the heater to the wall bracket, and engage lower
slots in the back with bracket.
Raise the heater to upright position and push the heater onto
bracket to engage top latch.
Turn on the heater using the ‘ ’ button and rotate the thermostat
knob to the desired position. When the room temperature has reached
the desired level, the power to the elements will be reduced, the
heater will then maintain the room temperature at the chosen level.
NOTE - Should your heater fail to come on when the thermostat
knob is at a low setting, this may be due to the room temperature
being higher than the thermostat setting.
Background Temperature
When used in conjunction with a remote programming device
supporting a background/setback setting, the heater will automatically
operate at a room temperature setting of 50C less than the thermostat
setting when the programme is in background/setback mode.
Limiting the thermostat setting
Before wall mounting the product the installer may wish to limit the
heat selection knob movement for the operator. This may be achieved
by unclipping the knob and removing the two plastic pins (see Fig.
4) using pliers and inserting them in the preferred holes to limit the
knob movement. Replace the plastic cap.
C
D
CEP500E
CEP750E
CEP1000E
CEP1500E
CEP2000E
C
390
390
560
630
800
D
300
300
300
300
300
255 Min.
Fig. 2
Operation
Fig. 4
Switching On the Heater
The controls are located on the right hand side on top of the
appliance.
Notes to the Installer
Test Mode
The button marked ‘ ’ controls the electricity supply to the
electronic thermostat. An indicator beside the ‘ ’ button
shows when the unit is powered ‘ON’.
When the heater is connected via a pilot wire system, the test mode
allows the installer to check whether the heater is responding
correctly to the incoming pilot wire signal.
Before switching the heater on at the mains, rotate the thermostat
knob to the ‘MAX’ position, then press and hold the ‘
switching on the mains.
MAX
’ button whilst
The unit will now enter a test state for 4 mins. During this test
MIN
state the ‘
NEON
Neon on -
Fig. 3
’ neon will indicate the pilot wire status:
PILOT WIRE
CONTROLLER MODE
ON
Neon off -
OFF
Neon flashing fast approx every 0.1sec -
FROST
Neon flashing slow approx every 0.5 sec -
SETBACK
Setting Desired Temperature (see Fig. 3)
Accessory Modules
The heater is fitted with an adjustable thermostat enabling the room
temperature to be controlled by rotating the knob accordingly. The
min setting ‘ ’ represents a room temperature of approximately 50C
and may be used for protection against frost. The ‘MAX’ setting
represents a room temperature of approximately 300C. The ‘ ’ symbol
glows when the elements are actually heating.
Optional accessory modules are available for use with this range of
heaters - see separate User Instructions for details on the operation
of each accessory module.
Before fitting a control module switch the heater off at the mains
supply.
To insert a module, the plug-in protective cover on the right hand side
of the thermostat unit at the back of the heater must first be removed.
Insert a flat-head screwdriver into the side of the cover and prise
away from the heater - see Fig. 5.
Cleaning
Lift the cover away from the heater to reveal the slide in compartment.
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
Before commencing cleaning, unplug the heater and allow it to cool.
Disconnect the electricity supply to the appliance.
The outside can be cleaned by wiping it over with a soft damp cloth
and then dried. Do not use abrasive cleaning powders or furniture
polish, as this can damage the surface finish.
To release heater from the wall bracket for cleaning or redecoration,
depress latch on both brackets (see Fig. 2) and hinge forward.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it should
not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.
After Sales Service
Your product is guaranteed for one year from the date of purchase.
Fig. 5
Insert the accessory module into the slot ensuring it is positively
located in position - see Fig. 5.
Switch the heater on at the mains supply.
Safety - Overheat protection
For your safety this appliance is fitted with a thermal cut-out. In the
event that the product overheats for some reason, the cut-out
prevents excessive temperatures on the product by cutting the power
to the heater. Once the heater has cooled down, it will reset
automatically, it will continue to cycle on and off automatically until
the reason for overheating is removed.
Within this period, we undertake to repair or exchange this product
free of charge provided it has been installed and operated in
accordance with these instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales service you should contact our
customer services help desk on 0845 601 5111. It would assist us if
you can quote the model number, series, date of purchase, and
nature of the fault at the time of your call. The customer services
help desk will also be able to advise you should you need to purchase
any spares.
Please do not return a faulty product to us in the first instance as this
may result in loss or damage and delay in providing you with a
satisfactory service.
Please retain your receipt as proof of purchase.
Energy Saving Tips
Other Energy Saving Tips for Around the Home
The energy we use to heat, light and power our homes contributes
over a quarter of the UK’s carbon emissions, the principle contributor
to climate change.
1. Lights
Around half the energy used in the home is for heating and hot
water, so using your heating system efficiently will not only help the
environment, but also save you money!
Use low-energy bulbs wherever you can as they use less than a
quarter of the electricity used by ordinary light bulbs and last ten
times longer!
Energy efficiency tips for heating and hot water
2. Cooking
1. Don’t set the temperature too high…
By reducing the thermostat setting by just 1ºC can reduce your
energy use by as much as 10%. And if you’re going away for the
winter, leave the thermostat on the frost protection setting to provide
protection from freezing at a minimum cost.
Turn off lights whenever you leave a room for more than ten minutes.
Use the right size pan for the food and cooker hob.
Keep saucepan lids on - this enables you to turn down the heat.
Boil water for cooking in a kettle.
2. Use it where you need it…
Set the appropriate temperature on your heaters for the room they
are in; for example, leave the thermostat on a heater in a spare
bedroom on a lower setting.
3. Use it when you need it…
Use heaters fitted with timers or linked to central controllers to turn
the heating on only when you need it and automatically switch it off
when you don’t.
4. Curtains…
Close your curtains at dusk to stop heat escaping through the
windows.
5. Windows…
Nearly 25% of heat loss can occur through poorly insulated frames
and single glazing. If you can’t afford to double glaze all your windows,
go for the rooms you heat most.
6. Treat your hot water tank...give it a jacket
An insulating jacket for hot water tanks only costs a few pounds
and pays for itself within months. Fit one that’s at least 75mm (3")
thick and you could save £10-£15 a year.
7. Water …
Use a shower if you have one to save time, money and water.
Don’t set the thermostat too high on your water heater - 60oC/140oF
is usually adequate for bathing and washing.
Put the plug in when running hot water in your sink - leaving hot taps
running is both wasteful and expensive.
Ensure dripping taps are repaired quickly. In just one day, you could
waste enough water to fill a bath
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
CREDA HEATING
MILLBROOK HOUSE
GRANGE DRIVE
HEDGE END
SOUTHAMPTON
SO30 2DF
TEL: 0845 601 5111
FAX: 0845 604 2369
WEBSITE: WWW.CREDAHEATING.CO.UK
Republic of Ireland Tel:
01 842 4833
[c] GDC Group Ltd,
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of GDC Group Ltd.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement