INDEX
Page
Watch Information and Care
2-5
OPERATING INSTRUCTIONS
Basic Models
6-7
Date Models
8-9
Multi Models
10 - 13
Indiglo Models
14 - 15
Chronograph Models
15 - 53
Analog & Digital Models
54 - 63
Digital Models
64 - 67
Special Models
Tide
68 - 71
World Time
72 - 75
High Performance Models
Tide, Temperature & Compass
76 - 81
Solar
82 - 83
Depth
84 - 87
CONGRATULATIONS ON OWNING YOUR NEW NAUTICA WATCH
DEVELOPED FROM ADVANCED ELECTRONICS TECHNOLOGY,
THE MOVEMENT IS MANUFACTURED FROM THE BEST QUALITY
COMPONENTS AND POWERED BY A LONG LIFE BATTERY.
NAUTICA watches have been developed with the highest attention to
quality, function and detail, as befits the NAUTICA tradition.
Please read the following instructions carefully to fully understand all
of the functions of your finely crafted timepiece.
WATER-RESISTANCE
If your watch is water-resistant, it will be indicated on the watch face
or on the caseback.
• 50 Meter Water-Resistant watch withstands water pressure to
86p.s.i.a. (equals immersion to 164 feet or 50 meters below sea
level) and dust as long as crystal, crown and case remain intact.
• 100 Meter Water-Resistant watch withstands water pressure to
160p.s.i.a. (equals immersion to 328 feet or 100 meters below sea
level) and dust as long as crystal, crown and case remain intact.
• 200 Meter Water-Resistant watch withstands water pressure to
INDIGLO® NIGHT-LIGHT
If your watch has “INDIGLO” on the dial, your watch is equipped with
the INDIGLO Night-Light. To activate this feature, depress the crown or
the pusher on the left side of the watch to illuminate the entire dial for
easy reading during nighttime or low light conditions. Light will appear
immediately.
Your NAUTICA watch featuring INDIGLO Night-Light contains a patented
electroluminescent technology (U.S. Patent Number 4,527,96 and
4,775,964). The INDIGLO Night-Light illuminates the entire watch lens
with a uniform bright light that offers superior readability in all low light
and nighttime conditions. Simply press the appropriate button to activate.
WARNING: DO NOT PRESS THE BUTTON UNDER WATER AS THE
WATCH WILL NOT RETAIN WATER RESISTANCE.
INDIGLO is a registered trademark of Indiglo Corporation.
320p.s.i.a. (equals immersion to 656 feet or 200 meters below sea
level) and dust as long as crystal, crown and case remain intact.
NOTE: CROWN MUST BE SCREWED INTO THE CASE
PROTRUSION TO ASSURE WATER RESISTANCE.
Battery
Please recycle or dispose of battery properly. Do not dispose of battery in
the fire. Do not recharge battery. Keep loose batteries away from children.
WATCH IS NOT AN ISO 6425 CERTIFIED DIVE WATCH.
2
3
SCREW-IN SETTING CROWN
ATTENTION
This is a screw down crown
Do not pull
Please read instruction
booklet before operation
ELAPSED TIME RING
If your watch is equipped with a rotating outer dial with numbers and
indicators, this Elapsed Time Ring may be used to indicate the length
of time remaining for an activity or the starting time of an activity.
TIME REMAINING - set the outer ring so that the triangle is pointing
to the time the activity is to end.
STARTING TIME - set the triangle on the time the activity is to begin.
TACHYMETER
SCREW-IN SETTING CROWN STICKER
Some deep-depth water-resistant watches require the setting crown to
be screwed in to ensure water-resistancy. If your Nautica watch has
a transparent sticker at back of the case back (diagram above)
please unscrew the crown before setting your watch, and the
crown must be screwed in after setting the watch.
To screw in, push in the crown firmly against the thread protrusion and
hold it in while turning the crown clockwise. Continue to screw in the
crown light until it is tight .
4
A tachymeter measures the speed at which the wearer has traveled
over a measured distance, i.e., a measured mile on the highway. For
example, start the chronograph when you pass the starting point and
stop it when you pass the finish point. You can then read your speed
in units per hour off the tachymeter scale.
BAND ADJUSTMENT
To disconnect band from clasp, press in end of spring bar
(use pin or small paper clip) and separate link band from
clasp as illustrated.
To reassemble band to clasp, place spring bar in band and place end of
spring bar into desired hole in clasp. Press opposite end of spring bar in
and slide into clasp and position so tip snaps into corresponding hole.
5
BASIC Models
TIME
To set the time:
AB
AB
crown position
crown position
Y121, 2039, 2036, 608/1010
1. Pull crown to “B” position.
2. Turn crown clockwise /counter clockwise to correct time.
3. Push crown to “A” position.
VX10 / VX51 / YL60 / 4S20
AB
crown
position
336/168
6
7
Date Models
TIME
To set the time:
Date
ABC
1. Pull out crown to “C” position.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push in crown to “A” position.
crown position
CALENDAR
To set the calendar/date:
VX12 / VX42 / VX32 / VX82 / 2315 / 2115 / 2415 / AL32
Date
1. Pull out crown to “B” position.
2A.Turn crown clockwise / counter clockwise to correct date.
2B.Turn crown counter clockwise to correct date. (For VX33 only)
3. Push in crown to “A” position.
NOTE: The date changes automatically every 24 hours.
ABC
crown position
DAY
VX33
8
9
multi models
DATE
DATE
ABC
crown
position
DAY
DAY
24 HOUR
VX3J
ABC
crown
position
VX3L
24 HOUR
DAY
24 HOUR
ABC
ABC
crown
position
24 HOUR
crown
position
DATE
VX3R
VX3N / VX7N
DATE
DAY
DAY
VX36
ABC
ABC
crown
position
crown
position
DATE
10
VD79
DATE
TIME
To set the time:
1. Pull crown to “C” position.
2. Turn crown either way to correct time.
3. Push crown to “A” position.
DATE
To set the date:
Note: the date changes automatically every 24 hours.
1. Pull crown to “B” position.
2. Turn crown to correct date.
3. Push crown to “A” position.
DAY OF WEEK (for VX3J / VX3L / VX3N / VX36 / VX7N / VD79)
To set the day:
1. Pull crown to "C" position.
2. Advance time 24 hours to change the day.
3. Push crown to "A" position.
Note: 24 hour indicator can be changed only when setting the time.
11
TIME
To set the time:
DATE
crown position
DAY
24 HOUR
6P27
DATE
ABC
crown position
24 HOUR
6P23
DATE
Day
ABC
crown position
1. Pull crown to “C” position.
2. Turn crown either way to correct time.
3. Push crown to “A” position.
DATE
To set the date :
1. Pull crown to “B” position.
2. Turn crown counter clockwise to correct date.
3. Push crown to “A” position.
Note: The day changes automatically every 24 hours.
DAY OF WEEK (for 6P27 / 6P29)
To set the day:
1. Pull crown to “C” position.
2. Turn crown clockwise (hour hands rotate 24 hours) to correct day of
week.
3. Push crown to “A” position.
Note: The day of week changes automatically every 24 hours.
24 HOUR
6P29
12
13
Indiglo models
Date
ABC
crown position
CALENDAR
To set the date:
1. Pull crown to "B" position.
2. Turn crown counter clockwise or towards you to correct date.
3. Push crown to "A" position.
Note: The date changes automatically every 24 hours.
M905
To activate the Indiglo:
Press crown to indicate Indiglo night light.
TIME
To set the time:
1. Pull crown to "C" position.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to "A" position.
14
15
Chronograph models
StopWatch 1/20sec. hand
This Chronograph watch has three functions:
TIME, CALENDAR, STOPWATCH
PuSHER “A”
Small Second hand
TIME
To set the time:
STOPWATCH SECOND HAND
Stopwatch Minutes hand
Stopwatch Hour hand
YM92
Stopwatch
minute hand
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
PUSHER “A”
CALENDAR
To set the calendar:
Crown Position
chronograph hand
1/5 second
ABC
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
PUSHER “B”
second hand
YM91
minute hand
Permanent
second hand
PUSHER “A”
ABC
Crown Position
stopwatch
second hand
PUSHER “B”
STOPWATCH
This stopwatch is capable of measuring:
– 1/5 second elapsed up to 60 minutes.
– After 60 minutes, it will start counting again from “0” repeatedly up
to 12 hours.
Date
YM12 / YM1G
16
17
Before using the stopwatch, reset the stopwatch hands.
To the “12” and “0” position.
STANDARD STOPWATCH MEASUREMENT:
1. Press pusher “A” to start timing.
2. Press pusher “A” to stop timing.
3. Press pusher “B” to reset.
ACCUMULATED ELAPSED TIME MEASUREMENT:
1. Press
2. Press
3. Press
4. Press
5. Press
pusher
pusher
pusher
pusher
pusher
“A”
“A”
“A”
“A”
“B”
to
to
to
to
to
start timing.
stop timing.
restart timing.
stop 2nd timing.
reset.
Example of using split time measurement for two runners.
Two runners can be timed simultaneously; the first runner’s time
can be recorded while the second runner’s time will continue to be
accumulated until he finishes.
18
SPLIT TIME MEASUREMENT:
1. Press pusher “A” to start the timing of the first runner.
2. Press pusher “B” to stop and record the timing of the first runner.
(Once pusher B is activated, even though the stopwatch 1/20
sec. hand and the big stopwatch sec. hand stop on the dial, the
stopwatch still continues to time internally.)
3. Press pusher “B” to start the timing of the second runner. The
stopwatch sec. hand will jump to show internal accumulated time
and to carry on timing of the second runner.
4. Press pusher “A” to stop the timing of the second runner and record
the time.
5. Press pusher “B” for third time to reset, all stop watch hands will
return to 12 o’clock position.
TO ADJUST STOPWATCH HAND (for YM12 / YM91 / YM1G):
1. Pull crown to position “C”.
2. Press pusher “A” for 2 seconds, the stopwatch minute hand turns a
full cycle.
3. Press pusher “B” repeatedly to set stopwatch minute hand to “0”
position.
4. Press pusher “A” again for 2 seconds, the stopwatch second hand
turns a full cycle.
19
5. Press pusher “B” repeatedly to set stopwatch second hand to “0”
position.
6. Push crown to position “A”.
Remarks:
This is suggested to check the hour and minute hands to ensure they
are correct before pushing the crown back to position “A”
7. Press pusher “B” to “0” setting for the stopwatch min. / hour hand.
If the hand is not at “0” or “12” position, then, press pusher “B”
repeatedly, until the hand moves by each intervaI and returns to “0”
or “12” position.
8. Push crown to “A” position after the adjustments of all stopwatch
hands.
Note: Please make sure that the stopwatch is stopped and reset
before adjusting.
TO ADJUST STOPWATCH HAND (for YM92) :
1. Pull crown to “C” position.
2. Press pusher “A” for 2 seconds.
3. Press pusher “B” to “0” setting for the 1/20 sec. hand. If the hand
is not at “0” or “12” position, then, press pusher “B” repeatedly, until
the hand moves by each intervaI and returns to “0” or “12” position.
4. Press pusher “A” for 2 seconds.
5. Press pusher “B” to “0” setting for the stopwatch sec. hand. If the
hand is not at “0” or “12” position, then, press pusher “B” repeatedly,
until the hand moves by each intervaI and returns to “0” or “12”
position.
6. Press pusher “A” for 2 seconds.
20
21
This Chronograph watch has 3 functions:
minute hand
TIME, CALENDAR, STOPWATCH
24-hour hand
stopwatch munute hand
PUSHER “A”
ABC
hour hand
Crown Position
stopwatch second hand
PUSHER “B”
calender
second hand
FS00 / FS01
hour hand
minute hand
24-hour hand
ABC
Crown Position
PUSHER “B”
stopwatch second hand
second hand
calender
FS20 / FS21
22
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
CALENDAR
To set the calendar:
PUSHER “A”
stopwatch munute hand
TIME
To set the time:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
STOPWATCH
The stopwatch is capable of measuring and displaying 1/1 second unit
up to maximum 1 hour. The stopwatch minute hand synchronizes with
the stopwatch second hand.
1. Press pusher “A” to start timing.
2. Press pusher “A” again to stop timing.
3. Press pusher “B” to reset.
23
CORRECTING STOPWATCH HANDS
If after resetting the stopwatch hands it is found that they are not at
the '12' or '0' position, correct them as follows:
1. Pull crown to “ C” position.
2. Press pusher “A” continuously, the stopwatch hand will advance
rapidly until it gets close to the “ 12” position. Then, press pusher “A”
repeatedly, the stopwatch hand will move by intervals until it returns
to “12” position.
3. Push crown back to “A” position.
4. Press pusher “A” to activate the stopwatch hand.
5. Press pusher “B” reset the stopwatch minute hand at 10 o’clock
until it returns to “0” position.
24
This Chronograph watch has 3 functions:
Permanent second hand
TIME, CALENDAR, STOPWATCH
minute Chrono hand
PUSHER “A”
ABC
STOPWATCH second hand
Crown Position
PUSHER “B”
Hour Chrono hand
DATE
5030D
DATE
Permanent second hand
minute Chrono hand
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown back to position “A”.
Calendar
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown back to position “A”.
PUSHER “A”
ABC
STOPWATCH second hand
Crown Position
PUSHER “B”
1/10 second counter hand (Hour
counter hand after 30 minutes)
5040B
26
STOPWATCH
This stopwatch is capable of measuring:
Chrono Hours elapsed up to 12 hours. ( 6 o’clock eye) (For 5030D)
Chrono Hours elapsed up to 10 hours. (6 o'clock eye) (For 5040B)
Chrono Minutes elapsed up to 30 minutes. ( 9 o’clock eye )
Stopwatch Second up to 1 minute. ( Big second hand )
27
Before using the stopwatch, reset stopwatch chrono hands to the “12”
and “0” position.
Standard Stopwatch Measurement
1. Press pusher “A” to start timing.
2. Press pusher “A” again to stop timing.
3. Press pusher “B” to reset.
Accumulated Elapsed Time Measurement
1. Press
2. Press
3. Press
4. Press
5. Press
pusher
pusher
pusher
pusher
pusher
“A”
“A”
“A”
“A”
“B”
to start timing.
again to stop timing.
to restart timing.
again to stop second timing.
to reset.
Split Time Measurement
Example of using split time measurement for two runners. Two runners
can be timed simultaneously; the first runner’s time can be recorded
while the second runner’s time will continue to be accumulated until he
finishes.
1. Press pusher “A” to start the timing of the first and second runner.
2. Press pusher “B” to stop and record the timing of the first runner.
28
(Once pusher “B” is activated, even though the chrono minute hand
and the big stopwatch sec. hand stop on the dial, the stopwatch still
continues to run internally.)
3. Press pusher “B” to catch up the timing of the second runner. The
stopwatch sec. hand will jump to show internal accumulated time
and to carry on timing of the second runner.
4. Press pusher “A” to stop the timing of the second runner and record
the time.
5. Press pusher “B” for third time to reset, all stopwatch chrono hands
will return to “12” and “0” position.
Corrective Mode for Stopwatch Chrono Hands
1. Pull crown to position “C”.
2. Press pushers “A” and “B” simultaneously for at least 2 seconds.
3. The big stopwatch sec hand rotates by 360 degree to activate
corrective mode.
To adjust the Big sec. Stopwatch hand
If it is not located at “12” or “0” position, either press pusher “A”
continuously or repeatedly until the hand moves by each interval and
returns to “12” and “0” position.
29
After finishing the big sec. stopwatch hand adjustment, press crown
back to position “A” to terminate the adjustment.
TO ADJUST THE 1/10 SECOND COUNT HAND (FOR 5040B)
After activating the corrective mode, if the 1/10 second counter hand
is not located at '12' or '0' position, press pusher “B” once to activate
the corrective mode of the 1/10 second counter hand. Press pusher “A”
continuously or repeatedly until the hand moves by each interval and
returns to “12” and “0” position.
Press crown back to position “A” to terminate the adjustment.
Press pusher “A” continuously or repeatedly until the hand moves by
each interval and returns to “12” and “0” position.
Press crown back to position “A” to terminate the adjustment.
Once finished adjusting all stopwatch chrono hands, press crown back
to “A” position to terminate adjustment.
To adjust the Hour chrono hand (for 5030D)
After activating the corrective mode, if the hour chrono hand is
not located at '12' or '0' position, press pusher “B” once to activate
the corrective mode of the hour chrono hand. Press pusher “A”
continuously or repeatedly until the hand moves by each interval and
returns to “12” and “0” position.
Press crown back to position “A” to terminate the adjustment.
To adjust the Minute chrono hand
After activating the corrective mode, if the minute chrono is not located
at '12' or '0' position, press pusher “B” twice to activate the corrective
mode of the minute chrono hand.
30
31
This Chronograph watch has three functions:
TIME, CALENDAR, STOPWATCH
24 hour hand
stopwatch
minute hand
PUSHER “A”
stopwatch
second hand
stopwatch
minute Disk
ABC
ABC
Crown
Position
PUSHER “B”
DATE
Stopwatch
minute hand
second hand
PUSHER “B”
OS2B
CALENDAR
To set the calendar:
24 hour hand
hour hand
PUSHER “A”
PUSHER “A”
ABC
ABC
Crown
Position
Stopwatch
minute hand
Crown
Position
PUSHER “B”
OS11
PUSHER “B”
stopwatch
second hand
Date
32
OS21
1. Pull crown to position "C".
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position "A".
DATE
Minutes hand
Minutes hand
stopwatch
second hand
permanent
second hand
Crown
Position
stopwatch
second hand
TIME
To set the time:
date
1. Pull crown to position "B".
2. Turn crown counter-clockwise to set calendar.
3. Push crown to position "A".
STOPWATCH
The stopwatch is capable of measuring and displaying time in 1/1
second united up to a maximum of 59 minutes 59 seconds.
1. Press pusher "A" to start timing.
2. Press pusher "A" again to stop timing.
3. Press pusher "B" to reset.
33
CORRECTING STOPWATCH HAND
If after resetting the stopwatch second hand it is found that they are
not at the '12' or '0' position, correct as follows:
1. Pull crown to "C" position.
2. Press pusher “A” continuously, the stopwatch second hand will
advance rapidly until it gets close to the “12” position. Then, press
pusher “A” repeatedly, the stopwatch second hand will move by
intervals until it returns to “12” position.
3. Push crown to position “A".
34
35
This Chronograph watch has 3 functions:
TIME, CALENDAR, STOPWATCH
24-hour hand
Stopwatch minute hand
ABC
Crown Position
PUSHER “B”
stopwatch second hand
DatE
VD53
stopwatch second hand
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
CALENDAR
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
PUSHER A
ABC
Crown Position
PUSHER B
Stopwatch minute hand
VD51
36
DatE
STOPWATCH
The stopwatch is capable of measuring:
1 minute elapsed up to 60 minutes.
Before using the stopwatch, reset the stopwatch hands to the “12” & “0”
position.
37
STANDARD STOPWATCH MEASUREMENT:
1. Press pusher “A” to start timing.
2. Press pusher “A” to stop timing.
3. Press pusher “B” to reset.
split time Measurement
Example of using split time measurement for two runners. Two runners
can be timed simultaneously; the first runner’s time can be recorded while
the second runner’s time will continue to be accumulated until he finishes.
1. Press pusher “A” to start the timing of the first and second runner.
2. Press pusher “B” to stop and record the timing of the first runner.
(Once pusher “B” is activated, even though the chrono minute hand
and the big stopwatch sec. hand stop on the dial, the stopwatch still
continues to run internally.)
3. Press pusher “B” to catch up the timing of the second runner. The
stopwatch sec. hand will jump to show internal accumulated time
and to carry on timing of the second runner.
4. Press pusher “A” to stop the timing of the second runner and record
the time.
5. Press pusher “B” for third time to reset, all stopwatch chrono hands
will return to “12” and “0” position.
38
TO ADJUST STOPWATCH HAND
1. Pull crown to position "C".
2. Press pusher "A" continuously or repeatedly to adjust the stopwatch
second hand to "0" or "12" position.
3. Press pusher "B" continuously or repeatedly to adjust the stopwatch
minute hand to "0" or "12" position.
4. Push back the crown to position "A".
39
Permanent Second Hand
Stopwatch Minute
Hand
PUSHER A
This Chronograph watch has 3 functions:
TIME, CALENDAR, STOPWATCH
ABC
Stopwatch Second Hand
Crown Position
DatE
PUSHER B
8171/201
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
Permanent Second Hand
Stopwatch Minute Hand
PUSHER A
Stopwatch Second Hand
ABC
Crown Position
PUSHER B
DatE
8171/202
Permanent Second Hand
PUSHER A
ABC
Crown Position
PUSHER B
Day
8172/220
40
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
DatE
Stopwatch Minute Hand
Stopwatch Second Hand
CALENDAR
To set the calendar:
DAY OF WEEK (For 8172/220)
To set the day:
1. Pull crown to “C” position.
2. Turn crown clockwise (hour hands rotate 24 hours) to correct day
of week.
3. Push crown to “A” position.
Note:The day of week changes automatically every 24 hours.
DatE
41
STOPWATCH
The stopwatch is capable of measuring:
1. 1 minute elapsed up to 30 minutes.
2. Chronograph hand 1/5 second.
Before using the stopwatch, reset the stopwatch hands to the “12” & “0”
position.
TO ADJUST STOPWATCH HAND:
1. Pull crown to position "B".
2. Press pusher "A" continuously or repeatedly to adjust the stopwatch
second hand to "0" or "12" position.
3. Press pusher "B" continuously or repeatedly to adjust the stopwatch
minute hand to "0" or "12" position.
4. Push back the crown to position "A".
STANDARD STOPWATCH MEASUREMENT:
1. Press pusher “A” to start timing.
2. Press pusher “A” to stop timing.
3. Press pusher “B” to reset.
SPLIT TIME MEASUREMENT:
1.
2.
3.
4.
5.
Press
Press
Press
Press
Press
pusher
pusher
pusher
pusher
pusher
“A” to start timing.
“B” to split.
“B’ to begin again.
“A’ to stop.
“B’ to reset.
42
43
stopwatch minute
hand
Date
ABC
stopwatch hour
hand
Crown Position
stopwatch second
hand
OS62
This Chronograph watch has three functions:
STOPWATCH
This stopwatch is able to measure and display time in 1/20 ( 1/1)
second united up to max 11 hrs 59 min 59 sec.
The retrograde stopwatch 1/20 ( 1/1) second hands keeps continuously
running for 60 seconds after starting, and then stops at "0" position.
1.
2.
3.
4.
Press pusher "B" to enter the chrono mode.
Press pusher "A" to start timing.
Press pusher "A" again to stop timing.
Press pusher "B" to reset.
TIME, CALENDAR, STOPWATCH
Note: Motion of the retrograde stopwatch is a demo. Actual measurement
will be shown when it stopped while "stop" button is pressed.
TIME
To set the time:
Correct the stopwatch hands
CALENDAR
To set the date:
1. Pull crown to position "B".
2. Press pusher "A" to set the stopwatch second hand to the "0"
position.
3. Press pusher "B" to set the stopwatch 1/20 second hand to the "0"
position.
4. The stopwatch hands can be advanced rapidly by continuously
pressing pushers "A' or "B".
5. Once the hands return to "0" position, reset time and push crown to
position "A".
1. Pull crown to position "C" , the small hand at 6 o'clock returns to
"60" position.
2. Turn crown clockwise to correct time.
3. Push crown to position "A", the small hand at 6 o'clock begins to run.
1. Pull crown to position "B".
2. Turn crown counter clockwise to correct date.
3. Push crown to position "A".
44
If after resetting the stopwatch hands it is found that they are not at
the '12' or '0' position, correct them as follows:
45
24 hour hand
PUSHER A
AB
Crown Position
PUSHER B
second hand
JS00
STOPWATCH
This stopwatch is able to measure and display time in 1 second
intervals up to max 29 min 59 sec.
It will stop automatically after running continuously for 30 minutes.
1. Press pusher "A" to start timing.
2. Press pusher "A" again to stop timing.
3. Press pusher "B" to reset.
Correcting the stopwatch hands:
If after resetting the stopwatch hands it is found that they are not at
the '12' or '0' position, correct them as follows:
This Chronograph watch has two functions:
TIME, STOPWATCH
TIME
To set the time:
1. Pull crown to position "B".
2. Turn crown clockwise to correct time.
3. Push crown to position "A", the second hand begins to run.
46
1. Pull crown to position "B".
2. Press pusher "A" to set the stopwatch second hand to the "0"
position.
3. The stopwatch minute hand is synchronized with the stopwatch
second hand and the second hand can be advanced rapidly by
continuously pressing pusher "A".
4. Once the hands return to "0" position, reset time and push crown to
position "A".
47
day hand
PUSHER A
stopwatch minute
hand
ABC
Crown Position
stopwatch second
hand
PUSHER B
second hand
Date
FS60 / FS61
This Chronograph watch has four functions:
TIME, CALENDAR, DAY OF WEEK, STOPWATCH
TIME
To set the time:
1. Pull crown to position "C".
2. Turn crown clockwise to correct time.
3. Push crown to position "A".
CALENDAR
To set the date:
1. Pull crown to position "B".
2. Turn crown clockwise to correct date.
3. Push crown to position "A".
48
DAY
To set the day:
1. Pull crown to position "B".
2. Turn crown counter clockwise to correct day.
3. Push crown to position "A".
STOPWATCH:
This stopwatch is able to measure and display time in 1 second
intervals up to max 59 min 59 sec.
After elapsed for 59 min. 59 sec, the stopwatch second hand resumes
timing from 0 second, the stopwatch minute hand continues and
accumulates timing of stopwatch until it is stopped by pressing pusher "A".
1. Press pusher "A" to start timing.
2. Press pusher "A" again to stop timing.
3. Press pusher "B" to reset.
Correcting the stopwatch hands
If after resetting the stopwatch second hand it is found that they are
not at the '12' or '0' position, correct it as follows:
1. Pull crown to position "C".
2. Press pusher "A" continuously, the stopwatch second hand will
advance rapidly until it gets close to “0” position.
3. Press pusher “B” to check that all stopwatch hands have been reset
to "0" position.
4. Press pusher "B" to check all stopwatch hands has been reset to
"0" position.
49
minute hand
4th center hand
PUSHER A
Upper hand
date
ABC
Chrono hours /
2nd time zone
Crown Position
hour hand
chrono minutes scale
PUSHER B
second hand
Lower hand
M363
This Chronograph watch has 3 functions:
TIME, CALENDAR, STOPWATCH
TIME
To set the time:
1. Pull crown to position ”C”
2. Turn crown clockwise / counter clockwise to correct the time.
3. Push crown back to position “A”.
CALENDAR
To set the Calendar:
1. Pull crown to position ”B”
2. Turn crown counter clockwise to correct the calendar.
3. Push crown back to position “A”.
STOPWATCH
This stopwatch is capable of measuring and displaying 1/5 second up
to maximum 4 hours.
1. Press pusher “A” to start the timing.
2. Press pusher “A” again to stop the timing.
3. Press pusher “B” to reset.
Note
– Press and hold pusher "B" anytime to restart the timing; the hand
will start running again after pusher "B" is released.
– The upper hand will move to "0" after the timing is reset; the watch
will return to display second time zone after eight seconds.
SECOND TIME ZONE
The upper hand shows the time for the second time zone; the scale is
24 hours.
50
51
To set the Second Time Zone:
1. Pull crown to position “B”. The 4th center hand will display the
minutes of the second time zone.
2. Press pusher “A” to set the hour of second time zone.
3. Press pusher “B” to set the minutes.
4. Push crown back to position “A”.
4th CENTER HAND ADJUSTMENT
1. Pull crown to position “C”. The upper and lower hand will reset to “0”
automatically.
2. Press pusher “A” or “B” to adjust the 4th center hand to “12”
position.
3. Push back the crown to position “A”.
52
53
analog and digital Models
start / stop
SET / indiglo
crown
lap / reset
mode
M12-1515
3. Press MODE to cycle through CHRONO, RECALL, TIMER, ALARM
and TIME modes. Press and hold MODE in any mode to return to
TIME display.
4. When setting digits, press START/STOP to go forward or LAP/
RESET to go backward or hold to change rapidly.
ANALOG TIME
To set the time:
1. Pull out the crown and turn clockwise or counter clockwise to
correct the time.
2. Push the crown in after complete setting.
This Analog and Digital watch has 6 function:
Analog and digital time display / Auto calendar 2000-2099 / Two time
zones / Two daily alarms linked to time zone / Three linked countdown
timers / Chronograph with 42-lap memory / Indiglo Night Light.
DIGITAL TIME AND CALENDAR
To set the time and calendar:
1. In TIME mode, press and hold START/STOP to shut off digital
display. Press once to turn back on.
2. Press SET/INDIGLO to illuminate watch face.
1. Press MODE until TIME appears. Press and hold SET/INDIGLO to
begin setting time.
2. Press START/STOP or LAP/RESET to set SECONDS to 0.
3. Press MODE to select HOURS digits.
4. Press START/STOP or LAP/RESET to advance. Go through 12
hours for AM or PM.
54
55
BASIC OPERATION
5. Press MODE to select MINUTES, YEAR, MONTH, DAY, DAY of
WEEK, 12 or 24 time display, MONTH-DAY or DAY-MONTH date
display. Press START/STOP or LAP/RESET to advance selected item.
6. Press SET/INDIGLO when done.
7. Press and hold LAP/RESET and wait for beep to change display to
second TIME ZONE. Repeat above to set time.
Note: once date is set, calendar runs automatically.
CHRONOGRPAH
1. Press MODE until CHRONO appears. Watch will briefly display
available storage (1-42).
2. Press START/STOP to start CHRONO.
3. Press LAP/RESET to take a lap. Display of running time resumes
after 5 seconds.
4. Press START/STOP to stop timing. Press again to resume.
5. While CHRONO is stopped, press MODE to enter RECALL mode.
Press START/STOP repeatedly to recall stored lap and split times.
6. Press and hold LAP/RESET to clear stored times. Chrono will
automatically clear. OR
7. In RECALL mode, press and hold LAP/RESET to reset and stored
laps/splits will automatically clear.
56
COUNTDOWN TIMER
1. Press MODE until TIMER appears. Press LAP/RESET to select
LOOP 1, 2 or 3. Timers will count upwards starting with last LOOP
TIMER set, unless last LOOP TIMER set is 3 (timers will then count
backwards from LOOP 3).
2. Press and hold SET/INDIGLO to set LOOP TIMER. Press START/
STOP or LAP/RESET to set seconds.
3. Press MODE to select MINUTES, press START/STOP or LAP/
RESET to set minutes.
4. Press MODE and then START/STOP or LAP/RESET to select next
LOOP.
5. Repeat above steps to set each additional LOOP.
6. Press SET/INDIGLO when done.
57
7. Press START/STOP to start or stop LOOP TIMER.
8. With TIMER stopped, press and hold SET/INDIGLO to reset all
LOOPS to zero.
At end of timed LOOP, next LOOP TIMER starts. Cycle is continuous
for up to 30 loops.
ALARM
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Press MODE until ALARM appears.
Press LAP/RESET to select ALARM 1 or 2.
Press and hold SET/INDIGLO to set.
Press START/STOP or LAP/RESET to set HOURS. Go through
12 hours for AM or PM.
Press MODE to select MINUTES, press START/STOP or LAP/
RESET to set.
Press MODE to select TIME ZONE for alarm, press START/STOP
or LAP/RESET to set.
Repeat to select MONTH and DAY. Leave blank for daily alarm.
Press SET/INDIGLO when done.
Repeat for second ALARM.
Press START/STOP to turn ALARM on or off.
58
) will appear in TIME display when ALARM is
Alarm symbol (
armed for that TIME ZONE.
Beep will sound when ALARM time is reached. Press any button to
silence alarm.
INDIGLO @ NIGHT LIGHT
Press SET/INDIGLO to illuminate watch face. Patented (U.S. pat.
4,527,096 and 4,775,964) electroluminescent technology used in the
INDIGLO® night-light illuminates entire watch face at night and in low
light conditions.
59
DIGITAL TIME AND CALENDAR
To set the time and calendar:
start / stop
light
crown
set
mode
MW36
This Digital watch has 7 functions
Analog and Digital Time display / Dual Time / Calendar / Chronograph
/ Timer / Alarm / Electroluminescent backlight
MODE SELECTION
Press “Mode” button to cycle through “TIME”, “ALARM”,
”CHRONOGRAPH” and “TIMER” mode.
1. Press “Mode” button until time mode appears.
2. Press and hold “Set” button to begin setting time.
3. Press “Mode” button to select the setting item in the order,
Second ➞ Minute ➞ Hour ➞ Time Format ➞ Month ➞ Date ➞ Day
of Week
4. Press "Start/Stop" button to set the time.
5. Press and hold the "Start/Stop" button to set time more rapidly.
6. Press “Set” button to exit the time setting.
DUAL TIME
1. Press
2. Press
3. Press
4. Press
5. Press
6. Press
“Start/Stop” button to display the dual time under time mode.
and hold “Set” button to begin setting time.
“Mode” button to select the hour or minute for setting.
“Start/Stop” button to set the hour or minute.
“Set” button after timing is completed.
“Start/Stop” button to return display to normal time.
ALARM MODE
ANALOG TIME
To set the time:
1. Pull out the crown and turn clockwise or counter clockwise to
correct the time.
2. Push the crown in after setting is complete.
60
In alarm mode, press “Start/Stop” button to enable or disable the Alarm
(
) and Chime (
) function.
Chime Function
The Beep will sound every hour after activate the chime function.
61
To set the Alarm:
1. Press
2. Press
3. Press
4. Press
5. Press
“Mode” button until alarm mode appears.
and hold “Set” button to begin setting alarm.
“Mode” button to select the alarm hour or minute for setting.
“Start/Stop” button to set the alarm hour or minute.
“Set” button to exit the alarm setting.
CHRONOGRAPH MODE
The chronograph counts up to 23 hours, 59 minutes, 59.99 seconds
with 1/100 second and split time function.
1. Press
2. Press
3. Press
4. Press
“Mode” button until chronograph mode appears.
“Start/Stop” button to start the chronograph.
“Start/Stop” button to stop the chronograph.
“Set” button again to reset the chronograph.
("SPL" will blink on the display if the split time function is active.
Even though the stop watch is not on display, the timing will
continue to run internally.)
3. Press “Set” button again to see the timing of the second runner.
The stopwatch will switch to display the internal accumulated time
and continue timing of the second runner.
4. Press “Start/Stop” button to stop the timing of the second runner
and record the time.
5. Press “Set” button to reset timing.
TIMER FUNCTION
1. Press “Start/Stop” button to start the timer.
2. Press “start/Stop” button to stop the timer.
3. Press “Set” Button to reset the timer.
To set the Timer:
Split time Measurement
Example of using split time measurement for two runners. Two runners
can be timed simultaneously; the first runner’s time can be recorded
while the second runner’s time will continue to be accumulated until he
finishes.
1. Press “Start/Stop” button to start the timing of the first and second
runner
2. Press “Set” button to stop and record the timing of the first runner.
62
1. Press
2. Press
3. Press
4. Press
5. Press
“Mode” button until timer mode appears.
and hold “Set” button to begin setting timer.
"Mode" button to select between hour or minute.
“Start/Stop” button to set the timer hour or minute.
“Set” button to exit the timer setting.
ELECTROLUMINESCENT BACKLIGHT
Press “Light” Button to activate the light function under each mode
anytime.
63
digital Models
TIME MODE
In time mode, the watch displays the current time information on hour,
minute, second, date, month and day of week. It also displays the
"ON/OFF" status of Alarm or Chime.
adjust
light
CHRONOGRAPH MODE
crown
set
mode
MW32
This Digital watch has 6 functions
Time / Calendar / Day of week / Chronograph / Alarm /
Electroluminescent backlight
MODE SELECTION
Press “Mode” button to cycle through “TIME”, ”CHRONOGRAPH”,
“ALARM” and “TIME SET” mode.
64
The sports watch counts up to 19 hours 59 minutes 59.99 seconds
with 1/100 second and split time function.
1. Press
2. Press
3. Press
4. Press
”Mode” button until chronograph mode appears.
“Adjust” button to start the chronograph.
“Adjust” button to stop the chronograph.
“Set” button again to reset the chronograph.
Split time Measurement
Example of using split time measurement for two runners. Two runners
can be timed simultaneously; the first runner’s time can be recorded
while the second runner’s time will continue to be accumulated until he
finishes.
1. Press “Adjust” button to start the timing of the first and second
runner
65
2. Press “Set” button to stop and record the timing of the first runner.
("Split" will blink on the display if the split time function is active.
Even though the stop watch is not on display, the timing will
continue to run internally.)
3. Press “Set“ button again to catch up the timing of the second
runner. The stopwatch will jump to show the internal accumulated
time and to carry on timing of the second runner.
4. Press “Adjust” button to stop the timing of the second runner and
record the time.
5. Press “Set” button to reset timing.
ALARM MODE
In alarm mode, press “Adjust” button to enable or disable the Alarm
and Chime function.
Alarm Function
1. Press ”Mode” button until Alarm mode appears.
2. Press “Set” button to select the alarm hour setting, the alarm will be
set to ON.
3. Press “Adjust” button to set the alarm hour.
4. Press “Set” button to select the alarm minute setting and press
“Adjust” button to set the alarm minute.
5. Press “Set” button again to fix the alarm setting.
66
Chime Function
The Beep will sound every hour after activating the chime function.
TIME SET MODE
1. Press “Mode” button until Time Set mode appears.
2. Press “Set” button to select the setting item in the order,
Second ➞ Hour ➞ Minute ➞ Month ➞ Date ➞ Day of Week
3. Press "Adjust" button to set the time.
4. Press and hold the "Start/Stop" button to set time more rapidly.
5. When setting the hour, the “H” indicate 24 hours mode, “A” or “P”
indicate 12 hours mode.
6. Press “Mode” button to exit the time setting mode.
ELECTROLUMINESCENT BACKLIGHT
Press “Light” button to activate the light function under each mode
anytime.
67
special function Models
Small
second hand
Minute Hand
PUSHER A
Tide amplitude and Moon
phase counter hand
ABC
Crown Position
Hour Hand
DatE
Tide cycle counter
PUSHER B
8272
Tide cycle hand
This Chronograph watch has 3 functions:
TIME, CALENDAR, TIDE
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
68
CALENDAR
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
TIDE FUNCTION
To set the Tide Function - Central Hand
The tide cycle takes place over one revolution of the dial in 12 hours
25 minutes and 14 seconds. High tide corresponds to the "12 o'clock"
position and low tide corresponds to the opposite position, hence "6
o'clock".
1. Press and hold pusher “B” to 3 seconds after the beep indicated
for enter in setting mode.
2. Press pusher “B” again to set the state of the local tide.
3. Continue pressing pusher “B” to enable rapid setting to be
performed.
Note: After 3 second without pressing pusher “B”, a beep indicated
exit from setting mode.
69
To set the Tide Amplitude (Moon Phase) – Counter at 10
o’clock small eye
The tide amplitude counter performs one revolution in 29 days 12
hours and 44 minutes.
1. Press and hold pusher “A” to 3 seconds after the beep indicated
for enter in setting mode.
2. Press pusher “A” again to set the tide amplitude corresponding to
the moon phase.
3. Continue pressing pusher “A” to enable rapid setting to be
performed.
Note:
– After 3 seconds without pressing pusher “A”, a beep indicates exit
from setting mode.
– The moon phase hand will start with its setting time, jumps step
forward every 24 hours.
70
71
4th center hand
minute hand
24 cities
PUSHER A
Upper hand
date
ABC
world time scale
CALENDAR
To set the CALENDAR:
1. Pull crown to position ”B”
2. Turn crown counter clockwise to correct the calendar.
3. Push crown back to position “A”.
Crown Position
hour hand
PUSHER B
PUSHER C
second hand
season scale
M366
lower hand
This watch has 4 functions:
TIME, CALENDAR, WORLD TIMES, SEASON
TIME
To set the time:
1. Pull crown to position ”C”
2. Turn crown clockwise / counter clockwise to correct the time.
3. Push crown back to position “A”.
72
WORLD TIME
To Set the World Time:
1. Pull crown to position “B”. The 4th center hand shows the world
time zone city and the upper hand shows the world time.
2. Press pusher “A” or “B” to move the 4th center hand to the city that
represents your home time zone.
3. Pull the crown to position “C”. The 4th center hand will revert back
to the 12:00 position. After five seconds, the upper hand moves and
shows the world time (the time of the city selected in previous step),
the center hand shows the minutes of the world time, and the lower
hand shows the season.
IMPORTANT: After pulling out the crown to position "C", don't press
any of the pushers and turn the crown until all hands stop moving.
(Approximately 10 seconds)
73
4. Press pusher “A” or “B” to move the 4th center hand backward or
forward to adjust the world time, respectively, to set the world time
zone to be the same as the home time zone. Press and hold a
pusher to change the time quickly. The hands move together as the
center hand makes one revolution, the upper hand moves one hour.
5. Press pusher “C” to adjust the season if the displayed season is
not correct for the home time zone. If the home time zone observes
daylight savings time, the upper hand will move by one hour.
6. Push crown to position "A" after setting is complete.
Note: If no pusher is pressed within five seconds of the hands
stopping, the watch will proceed to the world time setting
operation (see WORLD TIME setting).
SEASON SETTING
The season setting allows the watch to compensate for daylight
savings time (also called “summer time”).
Note: The world time scale is 24 hours.
The watch provides one setting to represent daylight savings time
and standard time. For the watch, the period of daylight savings
time is SUMMER and the period of standard time is WINTER. When
the season in one city is set to SUMMER, all cities in the same
hemisphere are automatically set to SUMMER, while all cities in the
other hemisphere are automatically set to WINTER. The watch knows
which cities are in each hemisphere.
4th CENTER HAND ADJUSTMENT
Press pusher “C” to adjust the season in the selected city.
City Time Display Selection:
Press pusher "A" or "B" to move the 4th center hand backward
or forward to select city. The upper hand will show the time in the
selected city.
1. Pull crown to position “C”. The upper and lower hand will reset to
the end of their sweeps automatically.
2. Press pusher “A” or “B” to adjust the 4th center hand to “12”
position.
3. Push back the crown to position “A”.
74
75
TIME
To set the time:
PUSHER A
1. Pull crown to position “C”
2. Turn crown clockwise / counter clockwise to correct time
3. Push crown to position “A”
A B C
crown
position
PUSHER C
PUSHER B
M314
CALENDAR
To set the calendar:
1. Pull crown to position “B”
2. Turn crown clockwise / counter clockwise to correct calendar
3. Push crown to position “A”
Note: Don’t change the date between 10pm and 2am as it
damage the watch movement.
This watch has 6 functions:
TIME, CALENDAR, TIDE, TEMPERATURE, COMPASS and NIGHT
LIGHT
Indiglo® Night-Light
Press the crown to activate the light.
76
could
InDICATor HAnD ADjuSTMEnT
1. Pull crown to position “C”
2. Press either TIDE or TEMP push button to move indicator hand until
it points to 12 o’clock.
3. Push crown to position “A” when done.
Note: Don't change the date between 10pm and 2am as it could
damage the movement.
77
TIDE / TEMPErATurE SElECTIon
Tide Function:
- Press B (TIDE) push button to select the tide
clock.
(The indicator hand moves to low tide and
then to current tide)
Tides are influenced by moon and sun and shape of shoreline,
so tide clock cannot precisely give times of high and low tides.
Periodic adjustment may be necessary.
To set the Tide Function – Indicator Hand
1. Pull crown to position “B”.
2. Press B (TIDE) push button to set the state of the local tide.
3. Push crown to position “A”.
Temperature Function:
- Press A (TEMP) push button to select the
thermometer.
(The indicator hand moves to beginning
of thermometer scale and then to current
temperature)
THErMoMETEr
Note: the indicator hand will not move if the
hand has already indicated the function you selected.
When worn on wrist, thermometer reading is affected by body heat.
For more accurate readings, remove watch and put in shade for at
least several minutes. Watch can measure water temperature also, if
submerged. Be sure to select temperature display before placing watch
in water, as buttons should not be pressed when watch is underwater.
Thermometer readings are taken every minute, and more frequently, if
temperature is changing.
TIDE CLOCK
compass calibration
Indicator hand always rotates clockwise, so tide is rising when
hand is pointing left and falling when pointing right. The tide cycle
takes place over one revolution of the dial in 12 hours 25 minutes and
14 seconds. High tide corresponds to the "12 o'clock" position and low
tide corresponds to the opposite position, hence "6 o'clock".
78
The compass must be calibrated before use. Since a compass uses the
earth’s magnetic field, you must be aware of large metallic objects, such
as vehicles or bridges, or objects that give off electromagnetic radiation,
such as televisions or computers, which could affect the magnetic
79
field around the watch. Do not store the watch near any source of
magnetism, such as a computer, appliance, or television, as the watch
can take on a magnetic charge, yielding inaccurate headings. Typical
accuracy of wrist-worn instruments is within +/- 10 degrees.
6. Press A or B pusher to move the indicator hand west (-) or east (+),
respectively, to point to your location’s declination angle using the
declination scale. Hold a button to move the hand quickly.
To calibrate the compass:
1. Pull the crown to position “B” and wait for the indicator hands to
stop moving.
2. Keep the watch in horizontal position and dial facing upward.
3. Press C (COMPASS) to begin. The indicator hand rotates two
revolutions to remind you to rotate the watch. While level, SLOWLY
rotate the watch two revolutions, taking at least 15 seconds per
revolution.
4. When done, press C (Compass), keeping
the watch level. The indicator hand
moves back and forth to acknowledge
the end of calibration and then moves to
the current magnetic declination setting.
5. If you do not wish to set the magnetic declination, push the crown
in. Otherwise, to have watch automatically compensate for the
declination angle, turn the compass ring until north is at 12 o’clock.
80
Magnetic declination set to -14° (14°W)
7. Push the crown to position “A” when done.
CoMPASS oPErATIon
Normally, the compass is inactive. While holding the watch level, press
C (COMPASS) to activate the compass. The indicator hand moves
to point north. If the watch is turned, the indicator hand will continue
to move, always pointing north. After 20 seconds, the compass will
automatically turn off and the indicator hand will return to the previous
function indicator. This conserves battery life. Press C (COMPASS) at
any time to keep the compass on for another 20 seconds.
Note: During compass operation, the second hand moves in twosecond increments.
81
SOLAR POWER
The guideline for charging time
A B C
Illumination
(Lx)
700
crown position
3,000
10,000
100,000
VS37
Source of
light
Environment
A fluorescent Inside the office
lamp
30W 20cm
Sun light
A
(Approx.
Hours)
B
(Approx.
Hours)
197
37
54
43
8
12
Cloudy
13
3
4
Fine weather
6
36 minutes
1
* For reference: 1,000Lx is 70cm under from 30W fluorescent lamp
TIME, CALENDAR and SOLAR POWER
Condition A: Time required for full charge
Condition B: Time required for steady operation
Condition C: Time to charge 1 day of power
TIME
To set the time:
Working time Approx. 6 months (After fully charged)
Charging time Approx. 6 hours (Under 100 KLX sunlight)
Approx. 43 hours (Under 3000LX fluorescent lamp)
This watch has 3 functions:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”
CALENDAR
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct date.
3. Push crown to position “A”.
NOTE: The date changes automatically every 24 hours.
82
C
(Approx.
Minutes)
Quick-start function
The watch will start operating immediately with second hand moving
at 2-second intervals when the watch is exposed to sunlight or strong
artificial light (of more than 1,000 Lx).
Power depletion warning function
The two-second interval movement of the second hand is a signal of energy
depletion.The watch continuous working time after two-second interval
movement is approximately 3 days.When the second hand starts moving at
two-second intervals, please charge the watch by exposing it to light.
83
DEPTH SCALE
CALENDAR
To set the calendar:
A B C
crown
position
4th center Hand
PUSHer
loWer Hand
M367
off indicator
1. Pull crown to position “B”
2. Turn crown counter clockwise to correct calendar
3. Push crown to position “A”
Note: Don't change the date between 10pm and 2am as it could
damage the movement.
*** Please pull up the crown cover before unscrewing the crown
for setting ***
TEMPERATURE
This watch has 4 functions:
Time, Calendar, Temperature and Depth Sensor
The temperature sensor is always on and will take reading at least
once every 60 seconds.
DEPTH SENSOR
Turn on the Sensor:
TIME
To set the time:
1. Pull crown to position “C”
2. Turn crown clockwise / counter clockwise to correct time
3. Push crown to position “A”
84
The depth sensor is normally off.
1. Press the pusher to turn on the sensor.
2. The 4th center hand will move from the OFF (6 o’clock) position
to the 12 o’clock position and begin to take readings at least once
every 5 seconds.
85
Note: If the readings remain in the range of 0 to 2 meters (0-6 feet) for
5 minutes, the sensor will turn off automatically.
and Replace Battery Level, with each level indicated by the movement
of the second hand.
Turn off the Sensor:
In Normal Level, the second hand will move one hand position every
one second.
After turning on the sensor, you can turn it off manually.
1. Press and hold pusher for 2 seconds.
2. The 4th center hand will move back to the OFF (6 o’clock) position.
Recall Maximum Depth/Minimum Temperature
1. Pull crown to position “B”.
2. The center and lower hands will move to display the maximum
recorded depth value and the minimum recorded temperature value
respectively.
3. The center and lower hands will move to display 0 meters/feet and
0ºC/32 ºF respectively if the watch has not yet been used.
4. The crown must be screwed back in prior to use to prevent any
water resistance issue.
In Battery Low Level, the second hand will only move at 2-second
intervals and shall move by two hand positions. It is recommended
that the user replace the battery.
In Replace Battery Level, the second hand will only move at 5-second
intervals and will move by five hand positions. At this point, dive
mode cannot be activated, and the user must replace the battery
immediately.
Battery Level Detection
The watch determines the battery level status and provides the user
with a visual indication corresponding to the current battery level. The
battery level status is classified as Normal Level, Battery Low Level,
86
87
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021