. OWNER`S MANUAL QX-3202

. OWNER`S MANUAL QX-3202
 'OWNER'S MANUAL
ОХ-3202
IN-WALL TIME CLOCK /AM/FM RADIO/
COMPACT DISC PLAYER
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR |
MOSTURE. DO NOT OPEN CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
The exclamation point within the triangle
A is a warning sign alerting you of important
Instructions accompanying the product.
The lightning flash and arrowhead within
the triangle is warning sign alerting you -
of “dangerous voltage” inside the product.
Please record the serial number located on the rear of the unit in the space below.
Serial Number
IMPORTANT NOTES
e Avoid installing the unit in locations described below: . Operate controls and switches as described in the manual
- Places exposed to direct sunlight or close to heat e Before turning the power switch on for the first time, make
radiating appliances such as electric heaters.
- On top of other stereo equipment that radiates too much
heat.
- Places lacking ventilation or dusty places.
~~ Humid or moist places.
sure all necessary connecting cords are properly installed.
IMPORTANT SAFEGUARDS
SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR AUDIO EQUIPMENT.
(FOR U.S.A)
CAUTION:
e Read all of these instructions. 6. Carts and Stands — The appliance should
e Save these instructions for later use. be used only with a cart or stand that is
e Follow all warnings and instructions marked on the recommended by the manufacturer.
audio equipment.
6A. An appliance and cart combination
1. Read Instructions - All the safety and operating should be moved with care.Quick stops excessive
instructions should be read before the appliance is operated. force,and uneven surfaces may cause the appliance and cart
2. Retain Instructions — The safety and operating instructions combination to overturn.
should be retained for future reference. Wall or Ceiling Mounting — The appliance should be
3. Heed Warnings — All warnings on the appliance and in the mounted to a wall or ceiling in accordance with the
operating instructions should be adhered to. mounting dimensions.
4. Follow Instructions — All operating and use instructions Ventilation — The appliance should be situated so that its
should be followed. location or position does not interfere with its proper
5. Water and Moisture — The appliance should not be used ventilation. For example, the appliance should not be
near water, for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement or near a swimming
pool. : -
situated on a bed, sofa, rug or a similar surface that may
block the ventilation openings; or place in a built-in
installation, such as a bookcase or cabinet that may impede
the flow of air through the ventilation openings.
10.
11.
12.
13.
14.
15.
Heat — The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
Power Sources — The appliance should be connected to a
power supply only of the type described in the operating
instructions or as marked on the appliance.
Grounding — The precautions that should be taken so that
‘the grounding means of the AC connecting power cord is
not defeated.
Power-Cord Protection — Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
Cleaning — The appliance should be cleaned with a slight
dampened cloth. Do not use harsh chemicals, cleaning
solvents, strong detergents, etc.
Power lines — An outdoor antenna should be located away
from power lines.
For Speaker Connections — Eighteen (18) American Wire
Gauge (AWG), Standard Wire, or larger, must be used. The
wire of preference is 18/2 AWG Standard. Failure to use 18
AWG Standard Wire, or larger, will void the product
warranty.
16.
Outdoor Antenna Grounding — If an outside antenna is
connected to the receive, be sure the antenna system is
grounded so as to provided some protection against voltage
surges and built up static charges. Section 810 of the
3
wire for both mast and lead-in.
. Secure lead-in wire from antenna to antenna discharge unit
and mast ground wire to house with stand-off insulators,
spaced from 4 feet (1.22 meters) to 6 feet (1.83 meters) apart. -
c. Mount antenna discharge unit close as possible to where lead-
— in enters house. An outside antenna system should not be
located in the Vicinity of overhead power lines or other
electric light or Power circuits, or where it can fall into such
power lines or Circuits. When installing an outside antenna
system, extreme Care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
17.
18.
19.
Non-use Periods — The power cord of the appliance should
be unplugged from the outlet when left un-used for a long
period of time. |
Object and Liquid Entry - Care should be taken so that
objects do not fall and liguids are not spilled into the
enclosure through openings.
Damage Requiring Service — The appliance should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
20.
B. Objects have fallen or liquid has been spilled on the
appliance.
С. The appliance has been exposed to rain or other
moisture. |
D. The appliance has been dropped or the enclosure
damaged. a.
Servicing — The user should not attempt to service the
appliance beyond that described in the operating
4
National Electrical Code. ANSI/NFPA NO. 70-1984,
provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection
to grounding electrodes and requirements for the grounding:
electrode. See Figure below,
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 610-207
GROUNDING CONDUCTORS
{NEC SECTION 310-20)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Notes: |
a. Use No. 10 AWG copper or No. 8 AWG aluminium or No. 17
AWG copper plate steel or bronze wire, or larger as ground
instructions. All other servicing should be referred to
qualified service personnel.
FRONT VIEW:
24
23
22
20
18 17
E
1514
BACK VIEW
27
O ©
H ^^ |
i GAUTION | |
| |
TALA: TO REDUCE THE FOF OF ELECTRIC SHOCK, |
HOT RERIHT COVER |
AO USER GERVIGEABLE PARTS MDE.
|| REFER SERVICIO TO CUALIFTEO SERVICE PORSCANEL
| WARNING: TO AVOID THE HAZARDS
| QF FIRE DR ELECTRICAL SHOCK,
i DONC EXPOSE THESE APPLIANCES
| TORAINOROTHERMOISTURE. |
O
©
\ ©
28
29
30
31
32
33
10
11
12
WIRE CONNECTION
SPEAKERS DIAGRAM
BLACK (3 GROUND
RED (+) BATTERY
CONNECTOR
YELLOW (+) BACK UP
LEFT SPEAKER(A} RIGHT SPEAKER(A)
ТЕ + BROWN | | GREY +
~ GREY W/BLK | BLUE W/BLK
NE + PURPLE
LEFT SPEAKER(B) RIGHT SPEAKER(B)
+ ORANGE WHITE +
T — WHITE W/ BLK T
LEFT SPEAKER(C) RIGHT SPEAKER(C)
7
CONTROLS: 18. Play/Pause Button
1. Power Indicator 19. Headphone Jack
2. CD /Aux/Radio Function Switch 20. Treble Control Knob
3. Time Clock 21. Bass Booster Button
4. AM/FM MO/ST Band Switch 22. Auxiliary Speaker C Selection Switch
5. Dial Scale 23. Auxiliary Speaker B Selection Switch
6. FM Stereo Indicator 24. Main Speaker A Selection Switch
7. AM/FM Tuning Knob 25. SET Button
8. MODE Button 26. Power Switch
9, Balance Knob 27. AM /Weather Band Antenna Post
10. Volume Control Knob 28. FM/AM Antenna Jack
11. Disc Open Close Function 29. Aux. Input Left Channel
12. CD IN/AUX Jack 30. Aux. Input Right Channel
13. Repeat Button 31. Line Output Left Channel
14. Program Button 32. Line Output Right Channel
15. Skip Up Button 33. DC Out jack
16. Skip Down Button
17. StopButton
INTRODUCTION
The QX-3202 is a mini compact electronic audio device with both function of CD Player/AM/FM Radio integrated in ONE. The mini
slim cabinet construction makes the unit an ideal wall radio for homes, mobile homes, custom vans, hotels/motels, etc.
Its features include:
— AM/FM/FM stereo tuner
— Laser Compact Disc Player
— Time Clock |
— Main Speaker A, Auxiliary Speaker B, and Auxiliary Speaker C output system
— LCD Display
— CD track memory
— Bass Booster/Treble control
— Line output Jack
— Aux./CD IN Jack
— Headphone Jack
NOTES: |
1. Connect the required speakers before operating the unit.
2. Use external antenna for optimum radio reception when necessary.
Speaker Installation
The QX-3202 is designed with outputs for speakers, Main speaker A , Auxiliary Speaker B, and Auxiliary Speaker C, Main Speaker A
output system is the master speaker output and is for speaker-pair installed close to the unit.
Auxiliary Speaker B output system provides you an additional speaker output pair for use in another location.
Auxiliary Speaker C output system provides you an additional speaker output pair for use in another location.
To install a speaker-pair to the Main Speaker À output system
1. Select two to four 4-ohm speakers.
2. Towire speakers refer to the wire connection diagram.(page 7)
If you also want to install speakers to the Auxiliary Speakers, just repeat steps 1 through 2
CAUTION: Each speaker output channel is marked with “+” and “-”, do not electrically connect them together.
EXTERNAL ANTENNA INSTALLATION
1. When installing an external antenna, pay close attention to the antenna safety instructions in “IMPORTANT SAFEGUARDS”.
2. To connect your external antenna to the unit's antenna jack, first have the external antenna’s connecting wire equipped with a
suitable connector that fits the antenna jack, then plug the connector into the jack.
3. AM/FM ANTENNA JACK. Circuit is connected internally, so you can receive AM and FM signals by connecting the external
antenna to any one of the ANTENNA terminals. о
LINE OUTPUT
I. Line Output Right Channel For external connection to the Right Input of your own amplifier.
2. Line Output Left Channel For external connection to the Left Input of your own amplifier.
AUX.INPUT
1. Function Switch to the AUX position.
2. CD IN/AUX on front panel or AUX IN Jack on back of the unit is for input of external CD or other AUXILIAR Y source.
Notes:
1. When connecting Line Output or Aux. Input jacks, remember to switch off both the QX-3202 and your amplifier or external source.
2. Each channel is marked “Right” and “Left”. Do not reverse the connections (AUX INPUT Jack is located on the rear of the Unit).
10
3. CDIN/AUX isa 3.5mm stereo plug input jack. (CD IN/AUX Jack located on the front panel.).
DC OUT
The DC Out put Jack is centered negative “HE >. Allows you to Connect it to your own amplifier.
Note: 1.When connecting DC QUT jack , remember to power off both the QX-3202 and your own amplifier.
2. Ensure polarity is correct.
3. The DC Out jack is available while the power of QX-3202 is at ON position.
HEADPHONE JACK
This unit is equipped with a Headphone Jack.
NOTE: Main speaker A, Auxiliary Speaker B , and Auxiliary Speaker C will all be louden when the headphones are plug in.
CLOCK & ALARM SETTING
To start the clock setting mode, Press the SET button (alarm time will begin to flash). Once in clock setting mode each press of the
SET button will cycle the clock as follows:
1 Press: Alarm hour will flash
2" Press: Alarm minute will flash
3” Press: Month will flash
4" Press: Date will flash
5% Press: Hour will flash
6" Press: Minute will flash
Once the function you wish to set begins to flash (alarm hour, alarm minute, month, etc.) press the MODE button to change to desired
setting. Press the SET button to move to the next function.
ALARM OPERATION
Once the desired time for the alarm has been set (see CLOCK & ALARM SETTING) turn on the alarm as follows:
1. Press the SET button (alarm time will begin to flash).
11
2. Press the MODE button (a small bell will appear indicates the alarm is on).
3. Pressing the MODE button a second time will turn on both alarm and hourly chimes. (Both the alarm indicator and chimes indicator
will appear in the right hand corner of the display).
4. Pressing the MODE button for a third time will turn only the chimes on (chimes ring hourly).
5. Pressing the MODE button for a forth time will turn both the alarm and chimes off.
RADIO OPERATION
1. Press POWER button to “ON’ position.
2. Slide Switch to the RADIO position.
3. Set VOLUME to desired level.
4, Press SPEAKER Select Switch (A) for (A) Speakers to have sound.
Press SPEAKER Select Switch (B) for (B) Speakers to have sound.
Press SPEAKER Select Switch (C) for (C) Speakers to have sound.
5. Switch the BAND Switch to your desired band. (AM, FM Stereo)
6. Rotate TUNER CONTROL knob to tune into your desired station. -
BASS BOOSTER
For the best result, Simply press BASS BOOSTER Switch to suit your listening preference. Depress BASS BOOSTER Switch to return
your normal listening result.
TREBLE CONTROL
Route the TREBLE knob to suit your listening preference.
CD OPERATION
Playing A Compact Disc |
1. Press the POWER button to the “ON” position.
12
2. Slide Switch to the CD position.
3. Press the OPEN/CLOSE button to open the disc tray.
4. Place the CD into tray with the printed side facing up. Press the OPEN/CLOSE button again to close the disc tray.
5. Disc information will appear on the LCD display. (Disc information includes the total track numbers)
6. Press the PLAY/PAUSE button to play CD.
7. To stop playing, press the STOP button.
‘Note: When you can’t open the disc tray, you can press again the OPEN/CLOSE button.
SKIP DURING PLAY MODE
|. Press the SKIP-UP button to skip to the beginning of the next track.
2: Press the SKIP-DOWN button to skip to beginning of the current track.
SEARCH DURING PLAY MODE
1. Press the SKIP-UP button or SKIP-DOWN to quickly advance or reverse through the music at high speed.
2. Release the SKIP-UP button or SKIP-DOWN button to return to normal playing mode.
REPEAT
1. Press the REPEAT button to enter the One track repeat playing mode ‚The LCD will display “REPEAT”.
2. Press the REPEAT button again to enter the all tracks repeat playing mode. The LCD will display “REPEAT”.
3. Press the REPEAT button again to cancel the repeat function.
PAUSE MODE
1. While playing a CD press the PLAY/PAUSE button to pause playing.
~ 2. Press the PLAY/PAUSE button again to continue playing.
CD PROGRAMMING
1. While in CD standby mode, press the PROGRAM button (display will flash “00”
2. Select the track number by pressing SKIP UP or SKIP DOWN buttons.
3. Press the PROGRAMME button again to store selected track in memory,
13
4. Repeat above steps 2-3 to enter more tracks into the CD memory (you may store up to 19 tracks)
J. Press the STOP button while in programming mode to clear track from memory.
NOTE: While in CD standby mode , press the PROGRAM button followed by the PLAY button to start the program.
MOUNTING DIMENSIONS
Pan philips head screw 35mm x 40 mm x 4 pcs
Remark: Opening dimensions in wall is 206mm(Width) x 248mm(Height)
14
SPECIFICATIONS:
Power Supply
Main Speaker A
Auxiliary Speaker B
Auxiliary Speaker C
Audio Output Power
Speaker A +B+C
Dimensions
Radio Section
Frequency Ranges
CD Section
+. CD Type
Frequency Response
S/N Rate(A filter )
1) DC adaptor (Not included)
2)Input: DC 12V SA
4-ohm speaker, Max.2
4-ohm speaker, Max.2
4-ohm speaker, Max.2
5 W (Mazx.)
204mm (L) x 240mm(H) x 140mm (D)
AM 530 — 1700 KHz
FM 87.5 — 108 MHz
Front Loading
20 Hz-20KHz
90dB at 1 KHz 0dB
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement