Specification Sheet

Specification Sheet
1.877.817.6028
www.DiodeLED.com
®
RGB WALL MOUNT COLOR CONTOLLER
SPECIFICATION SHEET
# DI-0761
Specified Item #
Project
Location
Each package includes two remotes and one receiver. Remotes both
have similar function, but diffrerent form factor. Remotes are married to
receiver with a unique ID and do not require pairing.
SPECIFICATIONS
Remote Specifications
Receiver Specifications
Input Voltage ¹
12VDC Battery (23A)
Input Voltage ¹
12-24VDC constant voltage
Wireless Signal
Radio Frequency (RF)
Max Current Load
3A x 3CH Max 9A
Transmitting Distance
130 ft.
Max Output Power
108W/216W (12V/24V)
Ambient Temperature ²
-4° ~ 122°F (-20° ~ 50°C)
Connection Type
Operating Temperature ³
-4° ~ 140°F (-20° ~ 60°C)
Terminal Block. Input and output
connections fit up to 14 AWG wire.
Control Type
PWM (Pulse Width Modulation)
Mounting
Recess or surface mountable with 3M™
or silicone adhesive.
Power Failure Memory
Yes
Ambient Temperature ²
-4° ~ 122°F (-20° ~ 50°C)
Handheld - 4.7 x 2.9 x 1.2 in. (L x W x H)
Wall Mount - 3.3 x 1.4 x .6 in.
Operating Temperature ³
-4° ~ 140°F (-20° ~ 60°C)
Environment
Indoor / dry location
Handheld - 1.2 oz.
Wall Mount - 4.0 oz.
Dimensions
5.1 x 1.6 x 1.2 in. (L x W x H)
Weight
2.6 oz.
Warranty
2 years
Dimensions
Weight
Note ¹ Ensure to specify a compatible driver and fixture with the same voltage specifications.
Note ² Do not install product in an environment outside the listed ambient temperature. Exceeding the maximum ambient temperature may damage
the controller and/or fixture. Ensure adequate airflow and heatsinking is considered when mounting/installing.
Note ³ Operating temperature is measured according to the minimum and maximum ambient temperature environment.
SS062014-1.1
info@DiodeLED.com
1 OF 3
www.DiodeLED.com
1.877.817.6028
www.DiodeLED.com
®
RGB WALL MOUNT COLOR CONTROLLER
SPECIFICATION SHEET
MECHANICAL DIAGRAMS
Wall Mount Remote
Handheld Remote
2.4 in.
.9 in.
ON/OFF
MODE
ON/OFF
PAUSE
BRIGHT
BRIGHT
SPEED
SPEED
MODE
MODE
4.7 in.
B-
B+
S-
S+
3.3 in.
4.2 in.
1.4 in.
2.9 in.
.6 in.
.3 in.
Receiver
.6 in.
3.9 in.
.6 in.
Power Indicator
1.6 in.
Signal Indicator
Input From
12-24VDC Driver
V+
V−
MODE
S-
S+
B+
B-
V+
R
To Low Voltage
LED Load
G
B
1.2 in.
.8 in.
5.1 in.
SS062014-1.1
info@DiodeLED.com
2 OF 3
www.DiodeLED.com
1.877.817.6028
www.DiodeLED.com
®
RGB WALL MOUNT COLOR CONTROLLER
SPECIFICATION SHEET
ADDITIONAL RESOURCES
Visit the online product page at www.DiodeLED.com for additional resources including:
• RGB WALL MOUNT COLOR CONTROLLER Installation Guide
For system diagrams and full installation/operating instructions.
• Voltage Drop Charts
Use to specify appropriate wire gauge for installation. Available at the ‘Tools & Resources’ page at www.DiodeLED.com.
SAFETY / WARNINGS / DISCLOSURES
• Install in accordance with the National Electric Code, and local regulations.
• This product is intended to be installed and serviced by a qualified, licensed electrician.
• Do not connect directly to high voltage 120V~277V power. Install with a compatible Class 2 constant voltage LED driver (power supply).
• Only install compatible LED drivers and fixtures. Contact technical support or visit the product page for compatible products.
• This product is rated for indoor installation and is not protected against moisture.
• Do not install product in an environment outside the listed ambient temperature. Ensure adequate airflow and heatsinking is considered when
mounting/installing.
• Operating temperature is measured according to the minimum and maximum ambient temperature environment. Exceeding the maximum operating
temperature may damage the controller or fixture.
• Proper heat dissipation will prolong the working lifespan of this product. Install in a well-ventilated area free from explosive gases and vapors.
• Ensure applicable wire is installed between driver, fixture, and any controls in between. When choosing wire, factor in voltage drop, amperage
rating, and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overhead wires, and cause a fire.
• Ensure wire leads at opposing ends of the tape light are not crossed when the fixture is turned on. It is acceptable to modify the length or cut off the
attached wire leads and DC connections in the field.
• Do not modify or disassemble this product beyond instructions or the warranty will be void.
WARRANTY
Limited Warranty
This product has a two (2) year limited warranty from the date of shipment. This warranty does not include the additional accessories referenced in this
specification sheet. Complete warranty details for fixtures and additional accessories are available at www.DiodeLED.com under the ‘Tools & Resources’
tab. For warranty related questions, please contact customer service.
Consumer’s Acknowledgment
Diode LED stands behind its products when they are used properly and according to our specifications. By purchasing our products, the purchaser
agrees and acknowledges that lighting design, configuration and installation is a complex process, wherein seemingly minor factors or changes in
layout and infield adjustments can have a significant impact on an entire system. Choosing the right components is essential. Diode LED is able to work
with the original purchaser to make an appropriate product selection to the extent of the limited information that the customer can provide, but it
is virtually impossible for Diode LED to design a system that foresees every unknown factor. For this reason, this Warranty does not cover problems
caused by improper design, configuration or installation issues. Any statement from a Diode LED employee or agent regarding a customer’s bill of goods
and/or purchase order is NOT an acknowledgement that the products purchased are designed and configured correctly. The purchaser agrees and
acknowledges that it is the customer’s responsibility to adhere strictly to all information contained in the Product Specification Sheets.
There is often more than one way to design, configure and layout an LED lighting application properly to achieve the same lighting effect. Diode
LED strongly recommends that licensed professionals be used in the design and installation of lighting systems that include Diode LED products.
The specifications include important information that a designer and installer should carefully review and strictly follow. Qualified designers and
certified and/or licensed installers, with access to the final installation environment, customer goals, and Diode LED product specifications can make
the requisite decisions appropriate for a successful finished lighting application.
SS062014-1.1
info@DiodeLED.com
3 OF 3
www.DiodeLED.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising