FORTIN 2019 Nissan Rogue Push Button Remote Starters and Alarm Systems Installation Guide
Fortin 2019 is an innovative device that allows users to conveniently control and monitor their vehicle's security and remote start functions. With features such as keyless entry, trunk release, and automatic arming/disarming, this system offers enhanced security and convenience. It also integrates seamlessly with your vehicle's original remote, eliminating the need for additional key fobs. The Fortin 2019 is compatible with a wide range of vehicles, making it a versatile solution for those seeking a reliable and user-friendly vehicle security system.
Advertisement
Advertisement
1-Page_entete
REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
REGULAR INSTALLATION
INSTALLATION RÉGULIÈRE
VEHICLE
VEHICULES
NISSAN
Rogue
Program bypass option
( If equiped with OEM alarm ):
Programmez l’option du contournement
( Si équipé d’une alarme d’origine ):
* HOOD
PIN
CONTACT
DE CAPOT
ONE
Push-to-start
Page 1 / 8
YEARS
ANNÉES
2014-2020
Program remote starter option:
Programmez l’option démarreur à distance:
Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme (fonctionnelles si équipé)
BYPASS FIRMWARE VERSION
VERSION LOGICIELLE CONTOURNEMENT
Program bypass option:
Programmez l’option du contournement:
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
SI LE VÉHICULE N’EST PAS ÉQUIPÉ
D’UN CONTACT DE CAPOT FONCTIONNEL:
D2
Program remote starter option for R.S. OEM
REMOTE STAND ALONE :
Programmez l’option démarreur à distance pour TÉLÉ-
COMMANDE D’ORIGINE
STAND ALONE :
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)
MUST BE INSTALLED IF THE VEHICLE CAN BE
• •
NISSAN/INFINITI MINIMUM
Parts required (Not included)
3x 1 Amp diode
72.
[ 48 ]
DESCRIPTION
Unlock before /
Lock after (Disarm
OEM alarm)
Déverrouille avant
/ Verrouille après
(Désarme l’alarme d’origine)
MANDATORY INSTALL | INSTALLATION OBLIGATOIRE
A11
CAPOT EST OUVERT, PROGRAMMEZ LA FONCTION A11 À NON.
MODE
34 2
34 3
MODE
38 2
OFF
NON
STATUT DE CAPOT : LE CONTACT DE CAPOT (INCLUS), DOIT ÊTRE
INSTALLÉ SI LE VÉHICULE PEUT DÉMARRER À DISTANCE, LORSQUE LE
REV.: 20211112
OFF
NON
OFF
NON
ON
OUI
OFF
NON
OEM Remote status (Lock/Unlock) monitoring
Suivi des status (Verrouillage/Déverrouillage) de la télécommande d’origine
Trunk Release
Ouverture de la valise
Activé : Appuyez x3 sur Verrouille de la télécommance d’origine pour démarrer à distance le véhicule.
AUTOCOLLANT DE
SÉCURITÉ
WARNING
ATTENTION
A2
Included
Inclus
Guide # 7764 1
ADDENDUM - SUGGESTED WIRING CONFIGURATION
ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
• • • • • • • • • • • •
A11
E5
DESCRIPTION
C1
D6
To add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
Pour ajouter la version logicielle et les options, utilisez l’outil FLASH LINK UPDATER ou FLASH LINK MOBILE , vendu séparément.
Hood trigger (Output Status).
By default The hazard will flash 4 times before start and 4x after the starting cycle.
Par défaut Les lumières du véhicule (Hazard) clignotent 4 fois avant le démarrage et
4x après le cycle de démarrage.
The hazard will flash 4 times before start and every 5 seconds after starting cycle.
Les lumières du véhicule (Hazard) clignotent 4 fois avant le démarrage et toutes les
5 secondes après le cycle de démarrage.
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
Notice: l'installation des éléments de sécurité est obligatoire. Le contact de capot et l'autocollant de sécurité sont des éléments de sécurité essentiels et doivent absolument être installés.
•
Contact de capot (état de sortie).
Push-to-Start
Push-to-Start
Pièce(s) requise(s) (Non incluse(s))
3x Diodes 1 Amp
SECURITY STICKER
DESCRIPTION
TRUNK OUTPUT. Pulse 2.5 Seconds.
SORTIE VALISE. Pulse 2.5 Secondes
Trunk output : Unlock before trunk pulse 0.5 sec
Sortie Valise : Déverrouillage avant Valise (0.5 seconde)
DESCRIPTION
Enable : Press 3x Lock to remote start with the OEM remote.
• •
THIS MODULE MUST BE INSTALLED BY A
QUALIFIED TECHNICIAN. A WRONG
CONNECTION CAN CAUSE PERMANENT
DAMAGE TO THE VEHICLE.
CE MODULE DOIT ÊTRE INSTALLÉ PAR
UN TECHNICIEN QUALIFIÉ, TOUTE
ERREUR DANS LES BRANCHEMENTS
PEUT OCCASIONNER DES DOMMAGES
PERMANENTS AU VÉHICULE.
•
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTION
START
(-)HAZARD
LIGHTS
(-) PTS
(-) IGNITION3
(-) IGNITION2 (-) IGNITION1
BCM located left of steering column.
BCM Situé à gauche de la colonne de direction.
CAN
HIGH
(-)DRIVER
DOOR PIN
(-)STARTER
OBD-II connector
Connecteur OBD-II
(+)12V
Back view
Vue de dos
GROUND (+)IGNITION4
Tail gate switch
Commutateur de Hayon arrière
(-) TAIL
GATE
Page 2 / 8
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
WIRING CONNECTION | GUIDE DE BRANCHEMENTS
HOOD PIN
CONTACT CAPOT
(+)Ignition
(-) Igni�on
(-) Starter
(-)Horn
(-) Lock
(-)Trunk Release
(-) Hood pin
(-) Hazard Lights
(-) PTS
(-) Unlock
(+)12V
(-)Ground
Yellow
Purple
In
Out
A1
A2
Purple/White Out A3
Green Out A4
White Out A5
Orange Out A6
Orange/Black Out A7
Dk.Blue
Out A8
Red/Blue
Lt.Blue/Black
In
In/Out
A9
A10
Black In A11
Pink Out A12
A13 Yellow/Black Out A13
Brown/White
Pink/Black
In A14
In A15
Purple/Yellow In/Out A16
Green/White In/Out A17
Green/Red In/Out A18
White/Black
Lt.Blue
Out
In/Out
A19
A20
White Out E1
Orange Out E2
Red
Black
Pink
In
In
In/Out
E3
E4
E5
Yellow Out E6
CUT LOOP FOR AUTOMATIC
TRANSMISSION MODE.
COUPEZ LA BOUCLE POUR LE
MODE TRANSMISSION
AUTOMATIQUE.
C2
C1
Brown
Gray/Black
Gray
Orange/Brown
Orange/Green
D3
D2
White/Red
White/Blue
White/Green
Yellow/Red
Yellow/Blue
Yellow/Green
CAN LOW
CAN HIGH
(-)Driver door pin
Ground
Page 3 / 8
A7
(-)HORN
Brown
Brun
6 5 4 3
12 11 10 9 8
2 1
7
OPTIONAL FACULTATIF
Steering Column. At switch, White 12-Pin connector.
Colonne de direction. Au commutateur,
Connecteur Blanc 12-pins.
A4
Rogue
A13
(-) TAIL
GATE
Lt.Green
Vert Pâle
A10
Brown
Brun
A20
Pink
Rose
A19
(-) PTS
Yellow
Jaune
A18
(-)HAZARD
LIGHTS
Yellow
Jaune
(-)
IGNITION2
Lt.Purple/
White
Mauve Pâle/
Blanc
(-)
IGNITION1
Yellow
Jaune
(-)
IGNITION3
Brown
Brun
C3
(~) CAN
HIGH
Blue
Bleu
D6
(-)DRIVER
DOOR PIN
Lt.Blue
Bleu Pâle
C4
(~) CAN
LOW
Pink
Rose
A5
(-)
STARTER
Green
Vert
E4
GROUND
Black
Noir
A1
Yellow
Jaune
4 3
8 7
2 1
6 5
20 19 18 17 16 15 14 13 12 11 10 8 7 6 5 4 3 2 1
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
20 20 19 18 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
40 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
12 11 10 9 8 7 6 5 4 3 2 1
24 23 22 21 20 19 18 17 16 15 14 13
1 2 3 5 6 7 8
9 10 11 12 13 14 15 16
E3
12V
White
Blanc
Back view -
8-Pin Green connector at switch.
Vue de dos -
Connecteur
Vert de 8-pins au commutateur.
Back view - BCM
Black 40-Pin connector
Vue de dos -
BCM Connecteur
Noir de 40-pins
Back view - BCM
Gray 40-Pin connector
Vue de dos -
BCM
Connecteur Gris de 40-pins
12 11 10
24 23 22
9
21
8
20
7
19
6 5 4
18 17 16
3
15
2
14
1
13
Back view - BCM
Green 40-Pin connector
Vue de dos -
BCM
Connecteur Gris de 40-pins
Back view - BCM
Black 24-Pin connector
Vue de dos -
BCM Connecteur
Noir de 24-pins
BCM located left of steering column.
BCM Situé à gauche de la colonne de direction.
Front View - White 16 pin OBDII
Connector
Vue de face -
Connecteur OBDII Blanc
16 pins
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DCRYPTOR PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION AVEC DCRYPTOR
2
Parts required (not included)
1x
FLASH LINK UPDATER
,
1x
FLASH LINK MANAGER
SOFTWARE | PROGRAMME
1x
Pièces requises (non incluses)
1x
FLASH LINK MOBILE
1x
1x
FLASH LINK MOBILE APP
(
Smartphone Android or iOS with Internet connection
Téléphone Intelligent
( des
Android ou iOS avec connection frais du fournisseur Internet peuvent s’appliquer )
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE. | AVANT LA PROGRAMMATION CONFIGURER LES OPTIONS DE L'UNITÉ ET SAUVEGARDER.
1 x1
HOLD
Press and hold the programming button:
Connect the 6-PIN Main harness (White connector).
Appuyez et maintenir le bouton de programmation enfoncé:
B ranchez l e harnais Principal à
6-Pins (connecteur Blanc) between BLUE, RED,YELLOW
& BLUE/RED flashes.
un clignotement BLEU,
ROUGE, JAUNE & BLEU/ROUGE
RELEASE
Release the programming button when the LED is BLUE.
Relâchez le bouton de programmation quand la DEL est BLEU.
ON
If the BLUE LED is not ON sol i d disconnect the 6-Pin Main connector and g o back to step 1.
3
J I
J I
J I
Insert the required remaining connectors.
Insérez les connecteurs requis restants.
Page 4 / 8
4 x1
PRESS
IGN ON
J I
IGNITION OFF
ON
IGNITION ON
OFF
Do not press the brake pedal.
Press the START/STOP button once to turn ON the ignition.
Ne pas appuyer sur la pédale de frein.
1 fois sur le bouton démarrage pour allumer l'ignition.
WAIT
FLASH
RAPIDLY
Wait,
The BLUE LED will flash rapidly.
Attendez,
La DEL BLEU clignotera rapidement.
5
OFF
J I
IGNITION ON IGNITION OFF
OFF
Press the START/STOP button once to turn OFF the ignition.
Appuyez 1 fois sur le bouton démarrage pour éteindre l'ignition.
The BLUE LED will t urn off.
La DEL BLEU s'éteint.
ALTERNATE
If the RED and YELLOW
LEDs alternate:
GO STEP 10 at Dcryptor process.
Si la DEL ROUGE et
JAUNE alternent:
ALLEZ À L'ÉTAPE 10 au processus du Dcryptor
OR
OU
RED ON
Si la DEL ROUGE s'allume:
ALLEZ À L'ÉTAPE 6 afin de complèter la programmation
ON
If the RED LED turn ON:
GO STEP 6 to complete the programing.
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
Page 5 / 8
KEY BYPASS PROGRAMMING PROCEDURE 2/3 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 2/3
6
IGN ON
J I
IGNITION ON
Do not press the brake pedal.
Press the Push -to-Start button once to turn on the ignition.
WAIT
Ne pas appuyer sur la pédale de frein.
Appuyez 1 fois sur le bouton démarrag e (Push-to-Start) pour allumer l'ignition.
ATTENDRE,
WAIT The YELLOW LED will turn
ON.
The RED LED will flash once.
La DEL JAUNE s'allumera.
La DEL ROUGE clignotera une fois.
7 x1
PRESS
OFF
J I
IGNITION ON
WAIT
ON
ON
IGNITION OFF
OFF
ON
Press the Push-to-Start button once to turn off the ignition.
WAIT
The YELLOW LED will turn
OFF.
Appuyez 1 fois sur le bouton démarrage (Push-to-Start) pour éteindre l'ignition.
ATTENDRE,
La DEL JAUNE s'éteindra.
8
IGN ON
J I
IGNITION ON
ON
ALTERNATE
Do not press the brake pedal.
Press the Push -to-Start button once to turn on the ignition.
WAIT
The YELLOW LED will turn
ON.
The RED LED will flash once.
Ne pas appuyer sur la pédale de frein.
Appuyez 1 fois sur le bouton démarrag e (Push-to-Start) pour allumer l'ignition.
ATTENDRE,
La DEL JAUNE s'allumera.
La DEL ROUGE clignotera une fois.
WAIT
The Red an d Yellow LEDs will start flashing alternatively.
Les DELs Rouge et Jaune clignoteront alternativement.
9 x1
PRESS OFF
Press the Push-to-Start button once to turn off the ignition.
Appuyez 1 fois sur le bouton démarrage (Push-to-Start) pour éteindre l'ignition.
10
J I
I
Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
Débranchez tous les connecteurs et ensuite le connecteur
6-pins (Connecteur principal) ou le connecteur
4-pins (Data-Link).
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
Page 6 / 8
KEY BYPASS PROGRAMMING PROCEDURE 3/3 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 3/3
11
12
J I
OR
OU
VEHICLE'S OBDII
CONNECTOR
CONNECTEUR OBDII
DU VÉHICULE
J I
FLASH LINK UPDATER*
FLASH LINK MOBILE*
J I
FLASH LINK MANAGER*
SOFTWARE | PROGRAMME
Microsoft Windows
Computer with
Internet connection*
Ordinateur Microsoft
Windows avec connection Internet*
J I
(
Smartphone* may apply )
Téléphone
Intelligent*
( des frais du
Internet peuvent s’appliquer )
Use the tool:
FLASH LINK UPDATER or
Utilisez l'outil:
FLASH LINK UPDATER ou
*Parts required (not included) *Pièces requises (non incluses)
AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 6-Pin (Main-
Harness) or the 4-pins (Data-Link) connector and after all the remaining connector.
APRÈS LA PROCÉDURE DE PROGRAMMATION
DCRYPTOR COMPLETÉE : retournez au véhicule et rebranchez le connecteur 6-pins (Connecteur principal) ou le 4-pins (Data-Link) et après tous les connecteurs.
The module is now programmed.
Le module est programmé.
REMOTE STARTER / ALARM VERIFICATION
DU DÉMARREUR À DISTANCE / ALARME
Test the remote
Testez starter.
le démarreur à distance.
à distance.
the vehicle.
Démarrez le véhicule
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
Page 7 / 8
REMOTE STARTER PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION DU DÉMARREUR À DISTANCE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE
MODULE FOR THE REMOTE STARTER PROGRAMMING.
RÉFÉREZ-VOUS AU GUIDE D’INSTALLATION RAPIDE INCLUS
AVEC LE MODULE POUR LA PROGRAMMATION DU DÉMARREUR
À DISTANCE.
REMOTE STARTER FUNCTIONALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE
Start UNLOCK x1
PRESS ON portes doivent
être fermées
Remote start the vehicle.
Démarrez à distance.
Unlock the doors with either:
• The OEM remote
• The remote-starter remote
• Or the proximity remote
Déverrouillez les portes avec soit:
• la télécommande d'origine
• la télécomande du démarreur à distance
• ou la télécommande de proximté.
Enter the vehicle with the
SMART-KEY.
Entrez dans le véhicule avec la clé intelligente
(SMART-Key) sur vous
DO NOT PRESS THE
BRAKE PEDAL.
Press and release the Push-to-Start button once.
NE PAS APPUYER LA
PÉDALE DE FREIN.
Appuyez et relâchez une fois le bouton démarrage
(Push-to-Start.
Press the brake pedal.
The vehicle can now be put in to gear and driven.
If the Smart-Key is not detected the vehicle will shut down.
Appuyez sur la pédale de frein.
Vous êtes maintenant prêt à embrayer et prendre la route.
Si la clé intelligente n'est pas détectées le véhicule s'éteindra.
Page 8 / 8
ONE
HARDWARE VERSION
Date: xx-xx
INTERFACE MODULE
PATENTS PENDING US: 2007-228827-A1
Made in Canada www.fortinbypass.com
Service No : 000 102 04 2536
Module label | Étiquette sur le module
Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d’installations
Des mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifi ez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE
L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifi er tous les fi ls et circuits avant d’effectuer les connexions.
Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifi é. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE | MISE À JOUR INTERNET

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Remote start your vehicle
- Lock and unlock your doors
- Track your vehicle's location
- Control your vehicle's lights and horn
- Receive alerts if your vehicle is tampered with
- Bypass your vehicle's factory immobilizer
- Compatible with most vehicles