Maytag Mvwb750yw Quick Specs
Top Loading Washer
PRODUCT MODEL NUMBERS
MVWB750Y, MVWB800Y,
MVWB850Y, MVWB950Y
Washer Dimensions:
14"* max.
(356 mm)
157⁄8"*
(403 mm)
3"*
(76 mm)
48 in.2*
(310 cm2)
24 in.2*
(155 cm2)
1"
(25 mm)
27 1/2"
(699 mm)
3"*
(76 mm)
1"
27"
1"
5"*
(25 mm) (25 mm)(686 mm) (127 mm)
Front view
Side view
Closet door
with vents
* Required spacing
Spacing for recessed area or closet installation
All dimensions show recommended spacing allowed, with tested
spacing of 0" (0 mm) clearance on sides.
■■ Additional spacing should be considered for ease of
installation and servicing.
■■ Additional clearances might be required for wall, door, and
floor moldings.
■■ Additional spacing should be considered on all sides of the
washer to reduce noise transfer.
■■ For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
■■ Companion appliance spacing should also be considered.
W10410358A
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is
recommended that a separate circuit serving only this appliance be provided.
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
41/2"
(114 mm)
Floor drain system
39"
(990 mm)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than 96"
(2.4 m) from bottom of washer. If you must install higher than 96"
(2.4 m), you will need a sump pump system.
Wall standpipe drain system
41/2"
(114 mm)
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. To order, please see toll-free phone
numbers in your “Use and Care Guide.” Minimum siphon break:
28" (710 mm) from bottom of washer. (Additional hoses may
be needed.)
Laundry tub drain system
41/2"
(114 mm)
30"
39"
(762
(990 mm)
See requirements for floor standpipe drain system.
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at
least 39" (990 mm) above floor; install no higher than 96" (2.4 m)
from bottom of washer.
IMPORTANT: To avoid siphoning, no more than 41⁄2" (114 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with cable tie.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
W10410358A
11/2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement