Installation and Operating Instructions
Bulletin 440P Small Metal Safety Position Switches with 4-Pin Male Micro (M12) Connectors
IMPORTANT: SAVE THESE INSTRUCTIONS FOR FUTURE USE.
This publication does not include all specifications, dimensions, or any special installation considerations. Refer to the product catalog pages for additional information.
ATTENTION To avoid electrical shock and unintended operation of equipment, disconnect all power to the limit switch and the controlled equipment before proceeding with any repair or adjustment of the limit switch.
Improper selection or installation of the devices affect the integrity of the safety systems.
Personnel injury or death, property damage or economic loss can result.
Comply with ISO 14119 including selection, accessibility to the installation, arrangement and fastening, possible substitute actuation, access to the escape release, motivation to defeat, and actuation mode.
Management controls, working procedures, training, and additional protective measures should be used to minimize the motivation to defeat and to manage the use and availability of spare actuators.
Comply with ISO 13857 and ISO 13855 for guard openings and minimum (safe) distances.
Comply with IEC 62061 or ISO 13849-1 and ISO 13849-2 for functional safety.
General Data
• Safety contacts: 1 N.C.
• Auxiliary contacts: 1 N.O.
• Enclosure rating:
• Type 1
• IP65
• Rugged die cast housing
• 15 cm (6 in.) pigtail with 4-pin male micro (M12) QD
• Compact profile for access limited installation
Principles, Standards, and Implementation
Before installation in a safety application, a risk assessment should be performed to determine whether the specifications of this device are suitable for foreseeable operational and environmental characteristics of the machine which is to be controlled. Only the normally closed set of contacts are considered safety contacts.
When applying these limit switches in a safety system application, all applicable standards for application should be followed.
Operating specifications must be followed and actuator must be displaced beyond the point where Direct Opening Action occurs.
These devices are not to be used to directly control a motor.
Specifications
Safety Ratings
Standards
Safety Classification
Certifications
ISO 13849-1, EN ISO 14119, EN 60204-1,
NFPA 79, EN 60947-5-1, ANSI B11.19 AS 4024.1
Cat. 1 Device per EN 954-1 Dual channel limit switch suitable for Cat. 3 or 4 systems cULus Listed, TÜV and CE Marked for all applicable directives
IMPORTANT
Installation of Allen-Bradley Guardmaster products should be in accordance with local and/or national codes. Servicing energized industrial control equipment can be hazardous if not in accordance with recommended safety procedures.
EN ISO 14119 replaces EN 1088 as the harmonized standard for interlocking devices associated with guards.
Functional safety information: http://literature.rockwellautomation.com/idc/groups/ literature/documents/sr/safety-sr001_-en-e.pdf
Outputs
Safety Contacts
Auxiliary Contacts
Thermal Current (/ lth
)
Rated Insulation Voltage (ui)
Short Circuit Protection
1 N.C. snap acting
1 N.O. snap acting
3 A
300V AC
3 A max. fast acting fuse IEC 269 type gG or equivalent
Class 2 power source required for this limit switch.
Maximum allowed:
1
AC DC
30V, 3 A 30V, 3 A
ATTENTION
No grounding conductor is provided.
Operating Characteristics
Actuation Speed, Max.
Actuation Speed, Min.
Actuation Frequency, Max.
Mechanical Life
Environmental
Enclosure Type Rating
Operating Temperature [C (F)]
Pollution Degree
2
Physical Characteristics
Housing Material
Actuator Material
Mounting
Vibration
Shock
Connection
Enclosure Color
250 mm/s
100 mm/min
6000 ops/hr
1 x 10
7
operations at room temperature
Type 1, IP65
2…70 ° (35.6…158 °)
3
Die cast alloy
Various polymers and metals
2 x M4, any position
IEC 60068-2-6 (10…55 Hz, 0.35 mm amplitude)
IEC 60068-2-7 (30 Gn 3 pulses per axis)
15 cm (6 in.) 4/22 AWG UL AWM 2464 pigtail with 4-pin male M12 QD
Red body/black head
WARNING F
1
For safe operation, the M12 female connector of the connecting cable must be rated 60V 3 A or higher per standard EN61984.
2
The M12 female connector of the connecting cable must have a minimum sealing of IP65 to maintain a pollution degree 3 rating.
Electrical life is dependent on load, therefore, operations are not applicable and withdrawn.
Product
440P
Intended Use
Cam actuated
ISO 14119 defines types of interlocking devices and coding:
Product
440P
Type
1
Coding
Uncoded
The products shown on this document conform with the Essential Health and
Safety Requirements (EHSRs) of the European Machinery Directive. They are third party certified to EN 60947-5-1 and EN ISO 14119.
Declaration of Conformity and certification: www.rockwellautomation.com/ certification/ce.page
Contact Opening Characteristics
Lever Positioning
Some rotary switches are supplied with levers that are mechanically coupled to the actuating shaft. The lever may be removed and re-installed for cam tracking adjustment. See table below for torque recommendations.
Torque Specifications
Location
3.5 mm Operator Head Phillips Screws
Short and Wide Roller Lever Arm 8 mm Hex Nut
Adjustable Lever Arm 4 mm Allen Head Screw
Adjustable Lever Arm Collar 3 mm Allen Head Screw
12 mm Panel Mount Nut
Wiring Diagram
Torque
0.8 N•m (7.1 lb•in.)
1.0 N•m (8.85 lb•in.)
1.8…2.8 N•m
(15.93…24.78 lb•in.)
3.2 N•m (28.32 lb•in.)
1.5 N•m (13.28 lb•in.)
Mounting Dimensions [mm (in.)]
Nonpanel Mount
Countersink Hole
\ • Panel mount clearance hole = 13 mm (0.51 in.) max.
Maintenance
These devices require little maintenance, but routine visual inspection is recommended to keep foreign debris from collecting on the exterior actuators and rollers. Removing the operator head is not recommended as loose internal components may be lost or improperly re-installed.
Actuation Guidelines
The method of actuation and over travel has significant influence on the service life of the limit switch. To maximize the service life, it is recommended to provide an actuator with a 30° pressure angle and a surface hardness of Rc-45 max.
4-Pin Male Micro (M12)
2
Mounting Dimensions [mm (in.)]
Panel Mount
30.4 (1.2)
34
(0.34)
Ø7.2 (0.28)
Ø4.2 (0.17)
43
(1.69)
20
(0.79)
25
(0.98)
M12x1 TAP
Ø8 (0.31)
24
(0.94)
43
(1.69)
20
(0.79)
25 (0.98)
30.4 (1.2)
35 (1.38)
Nonpanel Mount
Ø12 (0.47)
Ø7.2 (0.28)
Ø4.2 (0.17)
3.8 (0.15)
16 (0.63)
30.4 (1.2)
Panel Mount
Ø10.5 (0.41)
M12x1 TAP
3.7 (0.15)
40.6
(1.6)
43
(1.69)
20
(0.79)
25 (0.98)
Ø7.2 (0.28)
Ø4.2 (0.17)
35 (1.38)
30.4 (1.2)
3.8
(0.15)
24
(0.94)
43
(1.69)
20
(0.79)
25 (0.98)
Ø7.2 (0.28)
Ø4.2 (0.17)
16 (0.63)
Ø12 (0.47)
35 (1.38)
30.4 (1.2)
3.8
(0.15)
39.6
(1.56)
43
(1.69)
20
(0.79)
25 (0.98)
Ø7.2 (0.28)
Ø4.2 (0.17)
M12x1 TAP
16 (0.63)
Ø10.5 (0.41)
35 (1.38) 16 (0.63)
35 (1.38) 16 (0.63)
3
25
(0.98)
18
(0.71)
Mounting Dimensions [mm (in.)] (continued)
Note: Lever arm versions are nonpanel mount only.
30.4 (1.2)
5.2
(0.2) 35.8 (1.41)
43
(1.69)
20
(0.79)
25
(0.98)
Ø13.5
(0.53)
Ø7.2
(0.28)
Ø4.2
(0.17)
Short Lever Arm
8 mm Hex Nut
35 (1.38)
Ø13.5
(0.53)
25
(0.98)
18
(0.71)
30.4 (1.2)
43
(1.69)
20
(0.79)
25
(0.98)
25.4 (1)
Ø7.2
(0.28)
Ø4.2
(0.17)
Ø13.5
(0.53)
25
(0.98)
Wide Roller Lever Arm
8 mm Hex Nut
35.15 (1.38)
18
(0.71)
43
(1.69)
16 (0.63)
Ø16.5 (0.65)x7
R27 (Min)
R105 (Max)
Adj. Lever Arm 4 mm
Allen Head Screw
Two 4.2 (0.17) Dia. Holes
Countersink: 7.2 (0.28) Dia.
Depth: 4.2 (0.17)
Adj. Lever Arm Collar
3 mm Allen Head Screw
20 (0.79)
25 (0.98)
43.4 (1.71)
38.2 (1.5)
35 (1.38)
3.5 mm Operator Head
Philips Screw
16 (0.63)
35 (1.38)
ATTENTION
Operator heads with adjustable actuators should NOT be used for safety applications.
16 (0.63)
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page
.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 440P-IN016B-EN-P—10000153507 Ver 02—May 2015
Copyright © 2015 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
