Rosemount 8700M 8732EM, 8705, 8711, 8721 Magnetic Flowmeter Reference Manual

Reference Manual
00809-0100-4444, Rev AD
August 2015
Rosemount® 8700M
Magnetic Flowmeter Platform
with HART® Protocol
Reference Manual
00809-0100-4444, Rev AD
Rosemount® 8700M
Magnetic Flowmeter Platform
Read this manual before working with the product. For personal and system safety, and for
optimum product performance, make sure you thoroughly understand the contents before
installing, using, or maintaining this product.
Failure to follow these installation guidelines could result in death or serious injury.

Installation and servicing instructions are for use by qualified personnel only. Do not
perform any servicing other than that contained in the operating instructions, unless
qualified.

Verify the installation is done safely and is consistent with the operating environment.

If installed in explosive atmospheres [hazardous areas, classified areas, or an “Ex”
environment], it must be assured that the device certification and installation
techniques are suitable for that particular environment.

Explosion hazard. Do not disconnect equipment when a flammable or combustible
atmosphere is present.

To prevent ignition of flammable or combustible atmospheres, disconnect power
before servicing circuits.

Do not connect a Rosemount 8732EM Transmitter to a non-Rosemount sensor that is
located in an explosive atmosphere.

Substitution of components may impair Intrinsic Safety.

Follow national, local, and plant standards to properly earth ground the transmitter and
sensor. The earth ground must be separate from the process reference ground.

Rosemount Magnetic Flowmeters ordered with non-standard paint options or
non-metallic labels may be subject to electrostatic discharge. To avoid electrostatic
charge build-up, do not rub the flowmeter with a dry cloth or clean with solvents.
The electronics may store energy after power is removed. Allow ten minutes for charge to
dissipate prior to removing electronics compartment cover.

Explosions could result in death or serious injury.

Verify the operating atmosphere of the sensor and transmitter is consistent with the
appropriate hazardous locations certifications.

Do not remove the transmitter cover in explosive atmospheres when the circuit is live.

Before connecting a HART-based communicator in an explosive atmosphere, make
sure the instruments in the loop are installed in accordance with intrinsically safe or
non-incendive field wiring practices.

Both transmitter covers must be fully engaged to meet explosion-proof requirements.
iii
Reference Manual
00809-0100-4444, Rev AD
Failure to follow safe installation and servicing guidelines could result in death or serious
injury.

Installation should be performed by qualified personnel only.

Do not perform any service other than those contained in this manual.

Process leaks may result in death or serious injury.

The electrode compartment may contain line pressure; it must be depressurized before
the cover is removed.
High voltage that may be present on leads could cause electrical shock.

Avoid contact with leads and terminals.
Failure to follow these maintenance guidelines could result in death or serious injury.

Installation and servicing instructions should be performed by qualified personnel only.

Do not perform any servicing other than that contained in the operating instructions.

Verify that the operating environment of the sensor and transmitter is consistent with
the appropriate hazardous area approval.

Do not connect a Rosemount 8732EM to a non-Rosemount sensor that is located in an
explosive atmosphere.

Mishandling products exposed to a hazardous substance may result in death or serious
injury.

If the product being returned was exposed to a hazardous substance as defined by
OSHA, a copy of the required Material Safety Data Sheet (MSDS) for each hazardous
substance identified must be included with the returned goods.
Failure to follow these troubleshooting guidelines could result in death or serious injury.
iv

Installation and servicing instructions should be performed by qualified personnel only.

Do not perform any servicing other than that contained in the operating instructions.

Verify that the operating environment of the sensor and transmitter is consistent with
the appropriate hazardous area approval.

Do not connect a Rosemount 8732EM to a non-Rosemount sensor that is located in an
explosive atmosphere.

Mishandling products exposed to a hazardous substance may result in death or serious
injury.

If the product being returned was exposed to a hazardous substance as defined by
OSHA, a copy of the required Material Safety Data Sheet (MSDS) for each hazardous
substance identified must be included with the returned goods.

The Rosemount 8732EM Transmitter has not been evaluated for use with other
manufacturers' magnetic flowmeter sensors in hazardous (Ex or Classified) areas.

Special care should be taken by the end-user and installer to ensure the 8732EM
transmitter meets the safety and performance requirements of the other
manufacturer’s equipment.
Reference Manual
00809-0100-4444, Rev AD
Do not connect mains or line power to the magnetic flowtube sensor or to the transmitter coil
excitation circuit.
The products described in this document are NOT designed for nuclear-qualified applications.
Using non-nuclear qualified products in applications that require nuclear-qualified hardware or
products may cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact your local Emerson Process
Management Sales Representative.
v
Reference Manual
00809-0100-4444, Rev AD
vi
Reference Manual
Table of Contents
00809-0100-4444, Rev AD
August 2015
Contents
1Section 1: Introduction
1.1 System description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Product recycling/disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2Section 2: Installation
2.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.3 Transmitter symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4 Pre-installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.5 Installation procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.5.1
Transmitter installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.5.2
Identify options and configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.5.3
Mechanical considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.5.4
Electrical considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5.5
Environmental considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6 Handling and lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.7 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.7.1
Upstream/downstream piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.7.2
Flow direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.8 Sensor location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.8.1
Electrode orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.9 Sensor installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.9.1
Flanged sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.9.2
Flange bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.10 Wafer sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.10.1 Gaskets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.10.2 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
2.10.3 Flange bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.11 Process reference connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.12 Wiring the transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.12.1 Conduit entries and connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.12.2 Conduit requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.12.3 Connecting sensor to transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Table of Contents
vii
Reference Manual
Table of Contents
00809-0100-4444, Rev AD
August 2015
2.12.4 8732EM terminal block connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
2.12.5 Analog output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
2.12.6 Powering the transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
2.13 Cover jam screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
2.14 Basic configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
2.14.1 Basic setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
3Section 3: Advanced Installation Details
3.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
3.2 Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
3.3 Hardware switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
3.3.1
Alarm mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
3.3.2
Transmitter security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.3.3
Internal/external analog power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.3.4
Internal/external pulse power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.3.5
Changing hardware switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.4 Additional loops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
3.4.1
Connect pulse output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
3.4.2
Connect discrete output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
3.4.3
Connect discrete input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
3.5 Process reference connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
3.6 Coil housing configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
3.6.1
Standard coil housing configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
3.6.2
Process leak protection (option M1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
3.6.3
Process leak containment (Option M2 or M4). . . . . . . . . . . . . . . . . . . . . . .53
3.6.4
Higher temperature applications and sensor insulation best practices .54
4Section 4: Operation
4.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
4.2 Local operator interface (LOI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
viii
4.2.1
Basic features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
4.2.2
Data entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Table of Contents
Reference Manual
Table of Contents
00809-0100-4444, Rev AD
August 2015
4.2.3
Data entry examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
4.2.4
Totalizer functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
4.2.5
Display lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
4.2.6
Diagnostic messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
4.2.7
Display symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
4.3 Field Communicator interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
4.3.1
Field Communicator user interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
4.4 Process variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
4.4.1
PV - Primary variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
4.4.2
PV - Percent of range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
4.4.3
PV - Analog output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
4.4.4
Pulse output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
5Section 5: Advanced Configuration Functionality
5.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
5.2 Configure outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
5.2.1
Analog output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
5.2.2
Pulse output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
5.2.3
Totalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
5.2.4
Discrete input/output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
5.3 Configure HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
5.3.1
Variable mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
5.3.2
Poll address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5.3.3
Burst mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5.3.4
Configure LOI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
5.4 Additional parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.4.1
Coil drive frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.4.2
Process density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.4.3
Reverse flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.4.4
Low flow cutoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.4.5
PV damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.4.6
Signal processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.5 Configure special units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Table of Contents
5.5.1
Base volume unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
5.5.2
Conversion factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
ix
Reference Manual
Table of Contents
00809-0100-4444, Rev AD
August 2015
5.5.3
Base time unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
5.5.4
Special volume unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
5.5.5
Special flow rate unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
6Section 6: Advanced Diagnostics Configuration
6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
6.2 Licensing and enabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
6.2.1
Licensing the 8732EM diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
6.3 Tunable empty pipe detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
6.3.1
Tunable empty pipe parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
6.3.2
Optimizing tunable empty pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
6.4 Electronics temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
6.4.1
Turning electronics temperature on/off . . . . . . . . . . . . . . . . . . . . . . . . . .115
6.4.2
Electronics temperature parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
6.5 Ground/wiring fault detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
6.5.1
Turning ground/wiring fault on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
6.5.2
Ground/wiring fault parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
6.6 High process noise detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
6.6.1
Turning high process noise on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
6.6.2
High process noise parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
6.7 Coated electrode detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
6.7.1
Turning coated electrode detection on/off. . . . . . . . . . . . . . . . . . . . . . . .118
6.7.2
Coated electrode parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
6.8 4-20 mA loop verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
6.8.1
Initiating 4-20 mA loop verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
6.8.2
4-20 mA loop verification parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
6.9 SMART™ Meter Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
6.9.1
Sensor baseline (signature) parameters . . . . . . . . . . . . . . . . . . . . . . . . . .121
6.9.2
Establishing the sensor baseline (signature). . . . . . . . . . . . . . . . . . . . . . .122
6.9.3
SMART Meter Verification test criteria. . . . . . . . . . . . . . . . . . . . . . . . . . . .122
6.10 Run manual SMART Meter Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
6.10.1 Test conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
6.10.2 Test scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
6.11 Continuous SMART Meter Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
6.11.1 Test scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
6.12 SMART Meter Verification test results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
6.13 SMART Meter Verification measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
6.14 Optimizing the SMART Meter Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
x
Table of Contents
Reference Manual
Table of Contents
00809-0100-4444, Rev AD
August 2015
6.14.1 Optimizing continuous SMART Meter Verification. . . . . . . . . . . . . . . . . 131
7Section 7: Digital Signal Processing
7.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
7.2 Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
7.3 Process noise profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
7.4 High process noise diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
7.5 Optimizing flow reading in noisy applications . . . . . . . . . . . . . . . . . . . . . . . . . . 134
7.5.1
Coil drive frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
7.5.2
Auto zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
7.5.3
Digital signal processing (DSP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
7.6 Explanation of signal processing algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
8Section 8: Maintenance
8.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
8.2 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
8.3 Installing a Local Operator Interface (LOI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
8.4 Replacing 8732EM revision 4 electronics stack. . . . . . . . . . . . . . . . . . . . . . . . . . 143
8.5 Replacing socket module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
8.5.1
Integral mount socket module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
8.5.2
Replacing terminal block socket module . . . . . . . . . . . . . . . . . . . . . . . . . 147
8.6 Trims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
8.6.1
D/A trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
8.6.2
Scaled D/A trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
8.6.3
Digital trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
8.6.4
Universal trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
8.7 Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
9Section 9: Troubleshooting
9.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
9.2 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
9.3 Installation check and guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
9.3.1
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
9.3.2
Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
9.3.3
Remote wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
9.3.4
Process fluid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
9.4 Diagnostic messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
9.4.1
Table of Contents
Troubleshooting empty pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
xi
Reference Manual
Table of Contents
00809-0100-4444, Rev AD
August 2015
9.4.2
Troubleshooting ground/wiring fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
9.4.3
Troubleshooting high process noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
9.4.4
Troubleshooting coated electrode detection . . . . . . . . . . . . . . . . . . . . . 164
9.4.5
Troubleshooting 4-20 mA loop verification. . . . . . . . . . . . . . . . . . . . . . . 164
9.4.6
Troubleshooting the SMART Meter Verification test . . . . . . . . . . . . . . . 165
9.5 Basic troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
9.6 Sensor troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
9.6.1
Sensor adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
9.6.2
Socket module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
9.6.3
Installed sensor tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
9.6.4
Uninstalled sensor tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
9.7 Technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
9.8 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
AAppendix A: Specifications and Reference Data
A.1 Rosemount 8732EM Transmitter specifications. . . . . . . . . . . . . . . . . . . . . . . . . 177
A.1.1 Functional specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
A.1.2 Advanced diagnostics capabilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
A.1.3 Output signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
A.1.4 Sensor compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
A.1.5 Performance specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
A.1.6 Analog output effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
A.1.7 Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
A.1.8 F0875 Low Power Software Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
A.2 Rosemount 8705-M Flanged Sensor specifications . . . . . . . . . . . . . . . . . . . . . . 188
A.2.1 Functional specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
A.2.2 Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
A.3 Rosemount 8711-M/L Wafer Sensor specifications . . . . . . . . . . . . . . . . . . . . . . 194
A.3.1 Functional specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
A.3.2 Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
A.4 Rosemount 8721 Hygienic (Sanitary) Sensor specifications . . . . . . . . . . . . . . 198
A.4.1 Functional specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
A.4.2 Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
BAppendix B: Product Certifications
B.1 Product certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
B.2 FM hazardous locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
B.3 ATEX/IECEx hazardous locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
xii
Table of Contents
Reference Manual
Table of Contents
00809-0100-4444, Rev AD
August 2015
B.4 EC Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
CAppendix C: Wiring Diagrams
C.1 8732EM wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
C.2 775 Smart Wireless THUM™ Adapter wiring diagrams . . . . . . . . . . . . . . . . . . . 233
C.3 475 Field Communicator wiring diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
DAppendix D: Implementing a Universal Transmitter
D.1 Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
D.2 Universal capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
D.2.1 Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
D.3 Rosemount sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
D.3.1 8705/8707/8711/8721 sensors to 8732 Transmitter . . . . . . . . . . . . . . 240
D.3.2 8701 sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
D.3.3 Connecting sensors of other manufacturers . . . . . . . . . . . . . . . . . . . . . . 242
D.4 Brooks sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
D.4.1 Model 5000 sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . 243
D.4.2 Model 7400 sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . 244
D.5 Endress and Hauser sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
D.5.1 Endress and Hauser sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . 245
D.6 Fischer and Porter sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
D.6.1 Model 10D1418 sensor to 8732 transmitter. . . . . . . . . . . . . . . . . . . . . . 246
D.6.2 Model 10D1419 sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . 247
D.6.3 Model 10D1430 sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . 248
D.6.4 Model 10D1430 sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . 249
D.6.5 Model 10D1465/10D1475 sensors to 8732 Transmitter . . . . . . . . . . . 250
D.6.6 Fischer and Porter sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . 251
D.7 Foxboro sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
D.7.1 Series 1800 sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . 252
D.7.2 Series 1800 sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . 253
D.7.3 Series 2800 Sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . 254
D.7.4 Foxboro Sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
D.8 Kent Veriflux VTC sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
D.8.1 Veriflux VTC sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . 256
D.9 Kent sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
D.9.1 Kent sensor to 8732 Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
D.10 Krohne sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
D.10.1 Krohne sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Table of Contents
xiii
Table of Contents
August 2015
Reference Manual
00809-0100-4444, Rev AD
D.11 Taylor sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
D.11.1 Series 1100 sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . 259
D.11.2 Taylor sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
D.12 Yamatake Honeywell sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
D.12.1 Yamatake Honeywell sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . 261
D.13 Yokogawa sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
D.13.1 Yokogawa sensor to 8732 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . 262
D.14 Generic manufacturer sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
D.14.1 Generic manufacturer sensor to 8732 Transmitter . . . . . . . . . . . . . . . . 263
D.14.2 Identify the terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
D.14.3 Wiring connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
xiv
Table of Contents
Reference Manual
Section 1: Introduction
00809-0100-4444, Rev AD
August 2015
Section 1
1.1
Introduction
System description
The 8700M Magnetic Flowmeter Platform consists of a sensor and a transmitter. The sensor is
installed in-line with the process piping; the transmitter can be remotely mounted or integrally
mounted to the sensor.
Figure 1-1. Field Mount Transmitters
Integral
Remote
There are three Rosemount® flow sensors available.(1) See Figure 1-2.
Figure 1-2. Flow Sensors
8705
8711
8721
1. Also available for use with 8707 High Signal sensor with dual calibration (option code D2).
Introduction
1
Section 1: Introduction
Reference Manual
00809-0100-4444, Rev AD
August 2015
Figure 1-3. 8705 Cross Section
The flow sensor contains two magnetic coils located on opposite sides of the sensor. Two
electrodes, located perpendicular to the coils and opposite each other, make contact with the
liquid. The transmitter energizes the coils and creates a magnetic field. A conductive liquid
moving through the magnetic field generates an induced voltage at the electrodes. This voltage
is proportional to the flow velocity. The transmitter converts the voltage detected by the
electrodes into a flow reading.
1.2
Product recycling/disposal
Recycling of equipment and packaging should be taken into consideration and disposed of in
accordance with local and national legislation/regulations.
2
Introduction
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
Section 2
August 2015
Installation
Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Transmitter symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Pre-installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
Installation procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
Handling and lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10
Sensor location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11
Sensor installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12
Wafer sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17
Process reference connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 19
Wiring the transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 23
Basic configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 34
2.1
Introduction
This section covers the steps required to physically install the magnetic flowmeter. Instructions
and procedures in this section may require special precautions to ensure the safety of the
personnel performing the operations. Refer to the following safety messages before performing
any operation in this section.
2.2
Safety messages
Note
This section provides basic installation guidelines for the Rosemount® 8700M Magnetic
Flowmeter Platform with HART® protocol. For comprehensive instructions for detailed
configuration, diagnostics, maintenance, service, installation, or troubleshooting refer to the
appropriate sections in this manual. The quick start guide—as well as this manual—are available
online at www.rosemount.com.
Installation
3
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Failure to follow these installation guidelines could result in death or serious injury.









Installation and servicing instructions are for use by qualified personnel only. Do not
perform any servicing other than that contained in the operating instructions, unless
qualified.
Verify the installation is done safely and is consistent with the operating environment.
If installed in explosive atmospheres [hazardous areas, classified areas, or an “Ex”
environment], it must be assured that the device certification and installation
techniques are suitable for that particular environment.
Explosion hazard. Do not disconnect equipment when a flammable or combustible
atmosphere is present.
To prevent ignition of flammable or combustible atmospheres, disconnect power
before servicing circuits.
Do not connect a Rosemount 8732EM Transmitter to a non-Rosemount sensor that is
located in an explosive atmosphere.
Substitution of components may impair Intrinsic Safety.
Follow national, local, and plant standards to properly earth ground the transmitter
and sensor. The earth ground must be separate from the process reference ground.
Rosemount Magnetic Flowmeters ordered with non-standard paint options or
non-metallic labels may be subject to electrostatic discharge. To avoid electrostatic
charge build-up, do not rub the flowmeter with a dry cloth or clean with solvents.
NOTICE





2.3
The sensor liner is vulnerable to handling damage. Never place anything through the
sensor for the purpose of lifting or gaining leverage. Liner damage may render the sensor
inoperable.
Metallic or spiral-wound gaskets should not be used as they will damage the liner face of
the sensor. If spiral wound or metallic gaskets are required for the application, lining
protectors must be used. If frequent removal is anticipated, take precautions to protect
the liner ends. Short spool pieces attached to the sensor ends are often used for
protection.
Correct flange bolt tightening is crucial for proper sensor operation and life. All bolts must
be tightened in the proper sequence to the specified torque specifications. Failure to
observe these instructions could result in severe damage to the sensor lining and possible
sensor replacement.
In cases where high voltage/high current are present near the meter installation, ensure
proper protection methods are followed to prevent stray voltage / current from passing
through the meter. Failure to adequately protect the meter could result in damage to the
transmitter and lead to meter failure.
Completely remove all electrical connections from both sensor and transmitter prior to
welding on the pipe. For maximum protection of the sensor, consider removing it from the
pipeline.
Transmitter symbols
Caution symbol — check product documentation for details
Protective conductor (grounding) terminal
4
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
2.4
August 2015
Pre-installation
Before installing the Rosemount 8732EM Magnetic Flowmeter Transmitter, there are several
pre-installation steps that should be completed to make the installation process easier:

Identify the options and configurations that apply to your application

Set the hardware switches if necessary

Consider mechanical, electrical, and environmental requirements
2.5
Installation procedures
2.5.1
Transmitter installation
Installation of the Rosemount Magnetic flowmeter includes both detailed mechanical and
electrical installation procedures.
2.5.2
Identify options and configurations
The typical installation of the 8732EM includes a device power connection, a 4–20mA output
connection, and sensor coil and electrode connections. Other applications may require one or
more of the following configurations or options:

Pulse output

Discrete input/discrete output

HART multidrop configuration
Hardware switches
The 8732EM electronics stack is equipped with user-selectable hardware switches. These
switches set the alarm mode, internal/external analog power, internal/external pulse power, and
transmitter security. The standard configuration for these switches when shipped from the
factory are as follows:
Table 2-1. Standard Switch Configuration
Alarm Mode
High
Internal/External Analog Power
Internal
(1)
Internal/External Pulse Power
External
Transmitter Security
Off
(1)
1. For electronics with intrinsically safe analog and pulse outputs, the power
must be provided externally. In this configuration, these two hardware
switches are not provided.
In most cases, it will not be necessary to change the setting of the hardware switches. If the
switch settings need to be changed, follow the steps outlined in “Changing hardware switch
settings” on page 40).
Note
To prevent switch damage, use a non-metallic tool to move switch positions.
Installation
5
Section 2: Installation
Reference Manual
00809-0100-4444, Rev AD
August 2015
Identify any additional options and configurations that apply to the installation. Keep a list of
these options for consideration during the installation and configuration procedures.
2.5.3
Mechanical considerations
The mounting site for the 8732EM Transmitter should provide enough room for secure
mounting, easy access to conduit entries, full opening of the transmitter covers, and easy
readability of the Local Operator Interface (LOI) screen (if equipped).
For remote mount transmitter (8732EMRxxx) installations, a mounting bracket is provided for
use on a 2-in. pipe or a flat surface (see Figure 2-1).
Note
If the 8732EM is mounted separately from the sensor, it may not be subject to limitations that
might apply to the sensor.
Rotate integral mount transmitter housing
The transmitter housing can be rotated on the sensor in 90-degree increments by removing the
four mounting screws on the bottom of the housing. Do not rotate the housing more than
180 degrees in any one direction. Prior to tightening, be sure the mating surfaces are clean, the
O-ring is seated in the groove, and there is no gap between the housing and the sensor.
6
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Figure 2-1. Rosemount 8732EM Dimensional Drawing
>@
Note
Default conduit entries for FM approvals are 1/2-in. NPT. If M20 thread connections are required,
thread adapters will be supplied.
2.5.4
Electrical considerations
Before making any electrical connections to the 8732EM, consider national, local and plant
electrical installation requirements. Be sure to have the proper power supply, conduit, and other
accessories necessary to comply with these standards.
Both remotely and integrally mounted 8732EM Transmitters require external power so there
must be access to a suitable power source.
Installation
7
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Table 2-2. Electrical Data
Rosemount 8732EM Flow Transmitter
Power input
90–250VAC, 0.45A, 40VA
12–42VDC, 1.2A, 15W
Pulsed circuit
Internally powered (Active): Outputs up to 12VDC, 12.1mA, 73mW
Externally powered (Passive): Input up to 28VDC, 100mA, 1W
4-20mA output
circuit
Internally Powered (Active): Outputs up to 25mA, 24VDC, 600mW
Externally Powered (Passive): Input up to 25mA, 30VDC, 750mW
Um
250V
Coil excitation
output
500mA, 40V max, 9W max
Rosemount 8705-M and 8711-M/L Sensor(1)
Coil excitation
input
500mA, 40V max, 20W max
Electrode circuit
5V, 200uA, 1mW
1. Provided by the transmitter.
2.5.5
Environmental considerations
To ensure maximum transmitter life, avoid extreme temperatures and excessive vibration.
Typical problem areas include the following:

High-vibration lines with integrally mounted transmitters

Tropical/desert installations in direct sunlight

Outdoor installations in arctic climates
Remote mounted transmitters may be installed in the control room to protect the electronics
from the harsh environment and to provide easy access for configuration or service.
8
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
2.6
August 2015
Handling and lifting

Handle all parts carefully to prevent damage. Whenever possible, transport the system
to the installation site in the original shipping container.

PTFE-lined sensors are shipped with end covers that protect it from both mechanical
damage and normal unrestrained distortion. Remove the end covers just before
installation.

Keep the shipping plugs in the conduit connections until you are ready to connect and
seal them.

The sensor should be supported by the pipeline. Pipe supports are recommended on
both the inlet and outlet sides of the sensor pipeline. There should be no additional
support attached to the sensor.

Additional safety recommendations for mechanical handling:
-
Use proper PPE (Personal Protection Equipment) including safety glasses and
steel toed shoes).
-
Do not drop the device from any height.

Do not lift the meter by holding the electronics housing or junction box.The sensor liner
is vulnerable to handling damage. Never place anything through the sensor for the
purpose of lifting or gaining leverage. Liner damage can render the sensor useless.

If provided, use the lifting lugs on each flange to handle the Magnetic Flowmeter when
it is transported and lowered into place at the installation site. If lifting lugs are not
provided, the Magnetic Flowmeter must be supported with a lifting sling on each side
of the housing.
-
Standard Pressure 3-in. through 36-in. Flanged Magnetic Flowmeters come with
lifting lugs.
-
High Pressure (above 600#) 1-in. through 24-in. Flanged Magnetic Flowmeters
come with lifting lugs.
-
Wafers and Sanitary Magnetic Flowmeters do not come with lifting lugs.
Figure 2-2. Rosemount 8705 Sensor Support for Handling and Lifting
A
B
A. Without lifting lugs
B. With lifting lugs
Installation
9
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
2.7
Mounting
2.7.1
Upstream/downstream piping
To ensure specified accuracy over widely varying process conditions, install the sensor with a
minimum of five straight pipe diameters upstream and two pipe diameters downstream from the
electrode plane (see Figure 2-3).
Figure 2-3. Upstream and Downstream Straight Run
5 Pipe Diameters
2 Pipe Diameters
Fl ow
Installations with reduced upstream and downstream straight runs are possible. In reduced straight
run installations, the meter may not meet absolute accuracy specifications. Reported flow rates will
still be highly repeatable.
2.7.2
Flow direction
The sensor should be mounted so that the arrow points in the direction of flow. See Figure 2-4.
Figure 2-4. Flow Direction Arrow
10
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
2.8
August 2015
Sensor location
The sensor should be installed in a location that ensures it remains full during operation. Vertical
installation with upward process fluid flow keeps the cross-sectional area full, regardless of flow
rate. Horizontal installation should be restricted to low piping sections that are normally full.
Figure 2-5. Sensor Orientation
FLOW
FLOW
2.8.1
Electrode orientation
The electrodes in the sensor are properly oriented when the two measurement electrodes are in
the 3 and 9 o’clock positions or within 45 degrees from the horizontal, as shown on the left in
Figure 2-6. Avoid any mounting orientation that positions the top of the sensor at 90 degrees
from the vertical position as shown on the right in Figure 2-6.
Figure 2-6. Mounting Position
CORRECT
INCORRECT
For hazardous location installations, refer to Appendix B for Installation Drawings 08732-2060
and 08732-2062 for sensor orientation pertaining to specific T-code compliance.
Installation
11
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
2.9
Sensor installation
2.9.1
Flanged sensors
Gaskets
The sensor requires a gasket at each process connection. The gasket material must be compatible with
the process fluid and operating conditions. Gaskets are required on each side of a grounding ring
(see Figure 2-7). All other applications (including sensors with lining protectors or a grounding
electrode) require only one gasket on each process connection.
Note
Metallic or spiral-wound gaskets should not be used as they will damage the liner face of the
sensor. If spiral wound or metallic gaskets are required for the application, lining protectors
must be used.
Figure 2-7. Flanged Gasket Placement
B
A
FLOW
A. Grounding ring and gasket (optional)
B. Customer-supplied gasket
12
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
2.9.2
August 2015
Flange bolts
Note
Do not bolt one side at a time. Tighten both sides simultaneously. Example:
1. Snug upstream
2. Snug downstream
3. Tighten upstream
4. Tighten downstream
Do not snug and tighten the upstream side and then snug and tighten the downstream side.
Failure to alternate between the upstream and downstream flanges when tightening bolts may
result in liner damage.
Suggested torque values by sensor line size and liner type are listed in Table 2-4 for ASME B16.5
flanges and Table 2-5 for EN flanges. Consult the factory if the flange rating of the sensor is not
listed. Tighten flange bolts on the upstream side of the sensor in the incremental sequence
shown in Figure 2-8 to 20% of the suggested torque values. Repeat the process on the
downstream side of the sensor. For sensors with greater or fewer flange bolts, tighten the bolts
in a similar crosswise sequence. Repeat this entire tightening sequence at 40%, 60%, 80%, and
100% of the suggested torque values.
If leakage occurs at the suggested torque values, the bolts can be tightened in additional 10%
increments until the joint stops leaking, or until the measured torque value reaches the
maximum torque value of the bolts. Practical consideration for the integrity of the liner often
leads the user to distinct torque values to stop leakage due to the unique combinations of
flanges, bolts, gaskets, and sensor liner material.
Check for leaks at the flanges after tightening the bolts. Failure to use the correct tightening
methods can result in severe damage. While under pressure, sensor materials may deform over
time and require a second tightening 24 hours after the initial installation.
Figure 2-8. Flange Bolt Torquing Sequence
Installation
13
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Prior to installation, identify the lining material of the flow sensor to ensure the suggested
torque values are applied.
Table 2-3. Lining Material
Fluoropolymer liners
T - PTFE
F - ETFE
A - PFA
K - PFA+
Other liners
P - Polyurethane
N - Neoprene
L - Linatex (Natural Rubber)
D - Adiprene
Table 2-4. Suggested Flange Bolt Torque Values for Rosemount 8705 (ASME)
Fluoropolymer liners
Size
code
Line size
Class 150
(pound-feet)
Class 300
(pound-feet)
005
0.5-in. (15 mm)
8
8
N/A
N/A
010
1-in. (25 mm)
8
12
N/A
N/A
015
1.5-in. (40 mm)
13
25
7
18
020
2-in. (50 mm)
19
17
14
11
025
2.5-in. (65 mm)
22
24
17
16
030
3-in. (80 mm)
34
35
23
23
040
4-in. (100 mm)
26
50
17
32
050
5-in. (125 mm)
36
60
25
35
060
6-in. (150 mm)
45
50
30
37
080
8-in. (200 mm)
60
82
42
55
100
10-in. (250 mm)
55
80
40
70
120
12-in. (300 mm)
65
125
55
105
140
14-in. (350 mm)
85
110
70
95
160
16-in. (400 mm)
85
160
65
140
180
18-in. (450 mm)
120
170
95
150
200
20-in. (500 mm)
110
175
90
150
240
24-in. (600 mm)
165
280
140
250
300(1)
30-in. (750 mm)
195
415
165
375
(1)
36-in. (900 mm)
280
575
245
525
360
Class 150
Class 300
(pound-feet) (pound-feet)
Other liners
1. Torque values are valid for ASME and AWWA flanges.
14
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Table 2-5. Flange Bolt Torque and Load Specifications for 8705 (EN 1092-1)
Installation
Fluoropolymer liners (in Newton-meters)
Size
code
Line size
PN10
PN 16
PN 25
PN 40
005
0.5-in. (15 mm)
N/A
N/A
N/A
10
010
1-in. (25 mm)
N/A
N/A
N/A
20
015
1.5-in. (40 mm)
N/A
N/A
N/A
50
020
2-in. (50 mm)
N/A
N/A
N/A
60
025
2.5-in. (65 mm)
N/A
N/A
N/A
50
030
3-in. (80 mm)
N/A
N/A
N/A
50
040
4-in. (100 mm)
N/A
50
N/A
70
050
5.0-in. (125 mm)
N/A
70
N/A
100
060
6-in. (150 mm)
N/A
90
N/A
130
080
8-in. (200 mm)
130
90
130
170
100
10-in. (250 mm)
100
130
190
250
120
12-in. (300 mm)
120
170
190
270
140
14-in. (350 mm)
160
220
320
410
160
16-in. (400 mm)
220
280
410
610
180
18-in. (450 mm)
190
340
330
420
200
20-in. (500 mm)
230
380
440
520
240
24-in. (600 mm)
290
570
590
850
15
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Table 2-6. Flange Bolt Torque and Load Specifications for 8705 (EN 1092-1)
16
Other liners (in Newton-meters)
Size
code
Line size
PN 10
PN 16
PN 25
PN 40
010
1-in. (25 mm)
N/A
N/A
N/A
20
015
1.5-in. (40 mm)
N/A
N/A
N/A
30
020
2-in. (50 mm)
N/A
N/A
N/A
40
025
2.5-in. (65 mm)
N/A
N/A
N/A
35
030
3-in. (80 mm)
N/A
N/A
N/A
30
040
4-in. (100 mm)
N/A
40
N/A
50
050
5.0-in. (125 mm)
N/A
50
N/A
70
060
6-in. (150 mm)
N/A
60
N/A
90
080
8-in. (200 mm)
90
60
90
110
100
10-in. (250 mm)
70
80
130
170
120
12-in. (300 mm)
80
110
130
180
140
14-in. (350 mm)
110
150
210
280
160
16-in. (400 mm)
150
190
280
410
180
18-in. (450 mm)
130
230
220
280
200
20-in. (500 mm)
150
260
300
350
240
24-in. (600 mm)
200
380
390
560
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
2.10
Wafer sensors
2.10.1
Gaskets
August 2015
The sensor requires a gasket at each process connection. The gasket material selected must be
compatible with the process fluid and operating conditions. Gaskets are required on each side of
a grounding ring. See Figure 2-9 below.
Note
Metallic or spiral-wound gaskets should not be used as they will damage the liner face of the
sensor.
Figure 2-9. Wafer Gasket Placement
Installation
17
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
2.10.2
Alignment
On 1.5-in. through 8-in. (40 through 200 mm) line sizes, Rosemount requires installing the
alignment spacers to ensure proper centering of the wafer sensor between the process flanges.
1.
Insert studs for the bottom side of the sensor between the pipe flanges and center the
alignment spacer in the middle of the stud. See Figure 2-9 for the bolt hole locations
recommended for the spacers provided. Stud specifications are listed in Table 2-7.
2.
Place the sensor between the flanges. Make sure the alignment spacers are properly
centered on the studs. For vertical flow installations slide the O-ring over the stud to
keep the spacer in place. See Figure 2-9. Ensure the spacers match the flange size and
class rating for the process flanges. See Table 2-8.
3.
Insert the remaining studs, washers, and nuts.
4.
Tighten to the torque specifications shown in Table 2-9. Do not over-tighten the bolts
or the liner may be damaged.
Table 2-7. Stud Specifications
Nominal sensor size
Stud specifications
1.5 through 8-in. (40 through 200 mm)
CS, ASTM A193, Grade B7, threaded mounting studs
Table 2-8. Rosemount Alignment Spacer Table
Rosemount alignment spacer table
18
Line size
Dash no.
(-xxxx)
(in)
(mm)
Flange rating
0A15
0A20
0A30
0B15
AA15
AA20
AA30
AA40
AA60
AA80
AB15
AB20
AB30
AB40
AB60
AB80
DB40
DB60
DB80
DC80
DD15
DD20
DD30
1.5
2
3
1.5
1.5
2
3
4
6
8
1.5
2
3
4
6
8
4
6
8
8
1.5
2
3
40
50
80
40
40
50
80
100
150
200
40
50
80
100
150
200
100
150
200
200
40
50
80
JIS 10K-20K
JIS 10K-20K
JIS 10K
JIS 40K
ASME- 150#
ASME - 150#
ASME - 150#
ASME - 150#
ASME - 150#
ASME - 150#
ASME - 300#
ASME - 300#
ASME - 300#
ASME - 300#
ASME - 300#
ASME - 300#
EN 1092-1 - PN10/16
EN 1092-1 - PN10/16
EN 1092-1 - PN10/16
EN 1092-1 - PN25
EN 1092-1 - PN10/16/25/40
EN 1092-1 - PN10/16/25/40
EN 1092-1 - PN10/16/25/40
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Table 2-8. Rosemount Alignment Spacer Table (continued)
Rosemount alignment spacer table
Line size
Dash no.
(-xxxx)
(in)
(mm)
Flange rating
DD40
DD60
DD80
RA80
RC20
RC30
RC40
RC60
RC80
4
6
8
8
2
3
4
6
8
100
150
200
200
50
80
100
150
200
EN 1092-1 - PN25/40
EN 1092-1 - PN25/40
EN 1092-1 - PN40
AS40871-PN16
AS40871-PN21/35
AS40871-PN21/35
AS40871-PN21/35
AS40871-PN21/35
AS40871-PN21/35
To order an Alignment Spacer Kit (qty 3 spacers) use p/n 08711-3211-xxxx along with the Dash
no. above.
2.10.3
Flange bolts
Wafer sensors require threaded studs. See Figure 2-8 on page 13 for torque sequence. Always
check for leaks at the flanges after tightening the flange bolts. All sensors require a second
tightening 24 hours after initial flange bolt tightening.
Table 2-9. Rosemount 8711 Torque Specifications
2.11
Size code
Line size
Pound-feet
Newton-meter
015
1.5-in. (40 mm)
15
20
020
2-in. (50 mm)
25
34
030
3-in. (80 mm)
40
54
040
4-in. (100 mm)
30
41
060
6-in. (150 mm)
50
68
080
8-in. (200 mm)
70
95
Process reference connection
Figure 2-10 through Figure 2-13 illustrate process reference connections only. Earth safety
ground is also required as part of the installation but is not shown in the figures. Follow national,
local, and plant electrical codes for safety ground.
Use Table 2-10 to determine which process reference option to follow for proper installation.
Installation
19
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Table 2-10. Process Reference Installation Options
Grounding
straps
Grounding rings
Reference
electrode
Lining
protectors
Conductive
Unlined Pipe
See Figure 2-10
See Figure 2-11(1)
See Figure 2-13(1)
See Figure 2-13(1)
Conductive
Lined Pipe
Insufficient
Grounding
See Figure 2-11
See Figure 2-10
See Figure 2-11
Non-Conductive
Pipe
Insufficient
Grounding
See Figure 2-12
Not Recommended
See Figure 2-12
Type of pipe
1. Grounding ring, reference electrode, and lining protectors are not required for process reference. Grounding straps per Figure 2-10
are sufficient.
Note
For line sizes 10-in. and larger, the ground strap may come attached to the sensor body near the
flange. See Figure 2-14.
Figure 2-10. Grounding Straps in Conductive Unlined Pipe or Reference Electrode in Lined
Pipe
20
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Figure 2-11. Grounding with Grounding Rings or Lining Protectors in Conductive Pipe
Figure 2-12. Grounding with Grounding Rings or Lining Protectors in Non-conductive Pipe
Installation
21
Section 2: Installation
Reference Manual
00809-0100-4444, Rev AD
August 2015
Figure 2-13. Grounding with Reference Electrode in Conductive Unlined Pipe
Figure 2-14. Grounding for Line Sizes 10-in. and Larger
22
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
2.12
August 2015
Wiring the transmitter
This wiring section covers the wiring between the transmitter and sensor, the 4-20mA output,
and supplying power to the transmitter. Follow the conduit, cable, and electrical disconnect
requirements in the sections below.
For sensor wiring diagrams, reference Electrical Drawing 08732-1504 in Appendix C Wiring
Diagrams.
For hazardous locations, reference Installation Drawings 08732-2060 and 08732-2062 in
Appendix B .
For information on connecting to another manufacturer’s sensor, refer to Appendix D
Implementing a Universal Transmitter.
2.12.1
Conduit entries and connections
The standard conduit entries for the transmitter and sensor are 1/2 -in. NPT. Thread adapters are
provided for units ordered with M20 conduit entries. Conduit connections should be made in
accordance with national, local, and plant electrical codes. Unused conduit entries should be
sealed with the appropriate certified plugs. The flow sensor is rated IP68 to a depth of 33 feet
(10 meters) for 48 hours. For sensor installations requiring IP68 protection, the cable grands,
conduit, and conduit plugs must be rated for IP68. The plastic shipping plugs do not provide
ingress protection.
2.12.2
Installation
Conduit requirements

For installations with an intrinsically safe electrode circuit, a separate conduit for the
coil cable and the electrode cable may be required. Refer to the Installation Drawings in
Appendix B.

For installations with non-intrinsically safe electrode circuit, or when using the
combination cable, a single dedicated conduit run for the coil drive and electrode cable
between the sensor and the remote transmitter may be acceptable. Bundled cables
from other equipment in a single conduit are likely to create interference and noise in
the system. See Figure 2-15.

Electrode cables should not be run together and should not be in the same cable tray
with power cables.

Output cables should not be run together with power cables.

Select conduit size appropriate to feed cables through to the flowmeter.
23
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Figure 2-15. Best Practice Conduit Preparation
A
B
B
C
D
A. Power
B. Output
C. Coil
D. Electrode
2.12.3
Connecting sensor to transmitter
Integral mount transmitters
Integral mount transmitters ordered with a sensor will be shipped assembled and wired at the
factory using an interconnecting cable (see Figure 2-16). Use only the socket module or IMS
cable provided by Emerson™ Process Management.
For replacement transmitters use the existing interconnecting cable from the original assembly.
Replacement cables are available.
Figure 2-16. Interconnecting Cables
Remote mount transmitters
Cables kits are available as individual component cables or as a combination coil/electrode
cable. Remote cables can be ordered direct from Emerson Process Management using the kit
numbers shown in Table 2-11. Equivalent Alpha cable part numbers are also provided as an
alternative. To order cable, specify length as quantity desired. Equal length of component
cables is required.
Example: 25 feet = Qty (25) 08732-0065-0001
24
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Table 2-11. Component Cable Kits
Standard temperature (-20 °C to 75 °C)
Cable kit #
Description
Individual cables
Alpha
p/n
08732-0065-0001
(feet)
Kit, Component Cables, Std Temp
(includes Coil and Electrode)
Coil
Electrode
518243
518245
08732-0065-0002
(meters)
Kit, Component Cables, Std Temp
(includes Coil and Electrode)
Coil
Electrode
518243
518245
08732-0065-0003
(feet)
Kit, Component Cables, Std Temp
(includes Coil and I.S.Electrode)
Coil
Intrinsically Safe Blue Electrode
518243
518244
08732-0065-0004
(meters)
Kit, Component Cables, Std Temp
(includes Coil and I.S.Electrode)
Coil
Intrinsically Safe Blue Electrode
518243
518244
Extended temperature (-50 °C to 125 °C)
Cable kit #
Description
Individual cables
Alpha
p/n
08732-0065-1001
(feet)
Kit, Component Cables, Ext Temp.
(includes Coil and Electrode)
Coil
Electrode
840310
518189
08732-0065-1002
(meters)
Kit, Component Cables, Ext Temp.
(includes Coil and Electrode)
Coil
Electrode
840310
518189
08732-0065-1003
(feet)
Kit, Component Cables, Ext Temp.
(includes Coil and I.S.Electrode)
Coil
Intrinsically Safe Blue Electrode
840310
840309
08732-0065-1004
(meters)
Kit, Component Cables, Ext Temp.
(includes Coil and I.S.Electrode)
Coil
Intrinsically Safe Blue Electrode
840310
840309
Table 2-12. Combination Cable kits
Coil/electrode cable (-20 °C to 80 °C)
Cable kit #
08732-0065-2001
(feet)
08732-0065-2002
(meters)
08732-0065-3001
(feet)
08732-0065-3002
(meters)
Installation
Description
Kit, Combination Cable,
Standard
Kit, Combination Cable,
Submersible
(80°C dry/60°C Wet)
(33ft continuous)
25
Section 2: Installation
Reference Manual
00809-0100-4444, Rev AD
August 2015
Cable requirements
Shielded twisted pairs or triads must be used. For installations using the individual coil drive and
electrode cable, see Figure 2-17. Cable lengths should be limited to less than 500 feet (152 m).
Consult factory for length between 500–1000 feet (152–304 m). Equal length cable is required
for each.
For installations using the combination coil drive/electrode cable, see Figure 2-18. Combination
cable lengths should be limited to less than 330 feet (100 m).
Figure 2-17. Individual Component Cables
Figure 2-18. Combination Coil / Electrode Cable
26
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Cable preparation
When preparing all wire connections, remove only the insulation required to fit the wire
completely under the terminal connection. Prepare the ends of the coil drive and electrode
cables as shown in Figure 2-19. Limit the unshielded wire length to less than one inch on both
the coil drive and electrode cables. Any length of unsheathed conductor should be insulated.
Excessive removal of insulation may result in an unwanted electrical short to the transmitter
housing or other wire connections. Excessive unshielded lead length, or failure to connect cable
shields properly, may expose the unit to electrical noise, resulting in an unstable meter reading.
Figure 2-19. Cable Ends
Shock Hazard
Potential shock hazard across remote junction box terminals 1 & 2 (40V).
Explosion Hazard
Electrodes exposed to process. Use only compatible transmitter and approved installation
practices.
For process temperatures greater than 284 °F (140 °C), use a wire rated for 257 °F (125 °C).
Installation
27
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Figure 2-20. Remote Junction Box Views
Sensor
Transmiter
Wire
Terminal
Wire
Terminal
RED
BLUE
BLACK
YELLOW
WHITE
1
2
17
18
19
RED
BLUE
Shield
BLACK
YELLOW
WHITE
1
2
3
17
18
19
For sensor wiring diagrams, reference the installation drawings in Appendix C Wiring Diagrams.
For hazardous locations, reference the drawings in Appendix B Product Certifications.
2.12.4
8732EM terminal block connections
Remove the back cover of the transmitter to access the terminal block. See Figure 2-21 for
terminal identification. To connect pulse output and/or discrete input/output, reference
Appendix C Wiring Diagrams. For installations with intrinsically safe outputs, reference the
hazardous location installation drawings in Appendix B Product Certifications.
Figure 2-21. Terminal Block Connections
28
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
2.12.5
August 2015
Analog output
The analog output signal is a 4-20mA current loop. The loop can be powered internally or
externally via a hardware switch located on the front of the electronics stack. The switch is set to
internal power when shipped from the factory. For units with a display, the LOI must be removed
to change switch position.
Intrinsically safe analog output requires a shielded twisted pair cable.
For HART communication a minimum loop resistance of 250 ohms is required. It is
recommended to use individually shielded twisted pair cable. The minimum conductor size is
0.51 mm diameter (#24 AWG) for cable runs less than 5,000 feet (1,500m) and 0.81 mm
diameter (#20 AWG) for longer distances.
Internal power
The 4-20mA analog signal is a 24VDC active output.
Maximum allowable loop resistance is 500 ohms.
Wire terminal 1 (+) and terminal 2 (-). See Figure 2-22.
Figure 2-22. Analog Wiring—Internal Power
- 4-20mA
+ 4-20mA
Note
Terminal polarity for the analog output is reversed between internally and externally powered.
Installation
29
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
External power
The 4-20mA analog signal is passive and must be powered from an external power source.
Power at the transmitter terminals must be 10.8 - 30VDC.
Wire terminal 1 (-) and terminal 2 (+). See Figure 2-23.
Figure 2-23. Analog Wiring—External Power
+ POWER
- SUPPLY
Analog loop load limitations
Maximum loop resistance is determined by the voltage level of the external power supply, as
described in Figure 2-24.
Figure 2-24. Analog Loop Load Limitations
Load (Ohms)
600
0
Operating
Region
10.8
30
Power Supply (Volts)
Rmax =
Vps =
Rmax =
30
31.25 (Vps – 10.8)
Power Supply Voltage (Volts)
Maximum Loop Resistance (Ohms)
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
2.12.6
August 2015
Powering the transmitter
The 8732EM transmitter is available in two models. The AC powered transmitter is designed to
be powered by 90–250VAC (50/60Hz). The DC powered transmitter is designed to be powered
by 12–42VDC. Before connecting power to the 8732EM, be sure to have the proper power
supply, conduit, and other accessories. Wire the transmitter according to national, local, and
plant electrical requirements for the supply voltage. See Figure 2-25 or Figure 2-26.
Supply Current (DC Amps)
Figure 2-25. DC Power Requirements
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
12
16
20
24
28
32
36
40
Power Supply (DC Volts)
Peak inrush is 42A at 42VDC supply, lasting approximately 1ms.
Inrush for other supply voltages can be estimated with:
Inrush (Amps) = Supply (Volts) / 1.0
Figure 2-26. AC Power Requirements
AC Supply Characteristics
Supply Current (Amps)
0.24
0.22
0.20
0.18
0.16
0.14
0.12
90
110
130
150
170
190
210
230
250
Power Supply (VAC)
Installation
31
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Apparent Power (VA)
Apparent Power (VA)
34
32
30
28
26
24
22
20
90
110
130
150
170
190
210
230
250
Power Supply (VAC)
Peak inrush is 35.7A at 250VAC supply, lasting approximately 1ms.
Inrush for other supply voltages can be estimated with:
Inrush (Amps) = Supply (Volts) / 7.0
Supply wire requirements
Use 10–18 AWG wire rated for the proper temperature of the application. For wire 10–14 AWG
use lugs or other appropriate connectors. For connections in ambient temperatures above
122 °F (50 °C), use a wire rated for 194 °F (90 °C). For DC powered transmitters with extended
cable lengths, verify that there is a minimum of 12VDC at the terminals of the transmitter with
the device under load.
Electrical disconnect requirements
Connect the device through an external disconnect or circuit breaker per national and local
electrical code.
Installation category
The installation category for the 8732EM is OVERVOLTAGE CAT II.
32
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Overcurrent protection
The 8732EM transmitter requires overcurrent protection of the supply lines. Fuse rating and
compatible fuses are shown in Table 2-13.
Table 2-13. Fuse Requirements
Input
voltage
Fuse rating
Compatible fuse
90–250VAC
rms
1 Amp, 250V, I2t ≥ 1.5 A2s
Rating, Fast Acting
Bussman AGC-1, Littelfuse 31201.5HXP
12–42VDC
3 Amp, 250V, I2t ≥ 14 A2s
Rating, Fast Acting
Bel Fuse 3AG 3-R, Littelfuse 312003P, Schurter 0034.5135
Power terminals
See Figure 2-21 for terminal block connections.
For AC powered transmitter (90–250VAC, 50/60 Hz):

Connect AC Neutral to terminal 9 (AC N/L2) and AC Line to terminal 10 (AC/L1).
For DC powered transmitter:
2.13

Connect negative to terminal 9 (DC -) and positive to terminal 10 (DC +).

DC powered units may draw up to 1.2A.
Cover jam screw
For flow meters shipped with a cover jam screw, the screw should be installed after the
instrument has been wired and powered up. Follow these steps to install the cover jam screw:
1.
Verify the cover jam screw is completely threaded into the housing.
2.
Install the housing cover and verify the cover is tight against the housing.
3.
Using a 2.5 mm hex wrench, loosen the jam screw until it contacts the transmitter
cover.
4.
Turn the jam screw an additional 1/2 turn counterclockwise to secure the cover.
Note
Application of excessive torque may strip the threads.
5.
Installation
Verify the cover cannot be removed.
33
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
2.14
Basic configuration
Once the magnetic flowmeter is installed and power has been supplied, the transmitter must be
configured through the basic setup. The basic setup parameters can be configured through
either an LOI or a HART communication device.

For instructions on operation of the LOI or HART Communication device, refer to
Section 4.

If configuration beyond the basic setup parameters is required, refer to Section 5 for a
complete list of device parameters.
Configuration settings are saved in nonvolatile memory within the transmitter.
2.14.1
Basic setup
Tag
LOI menu path
Basic Setup, Tag
Traditional Fast Keys
Device dashboard
1,3,1
2,2,9,1,1
Tag is the quickest and shortest way of identifying and distinguishing between transmitters.
Transmitters can be tagged according to the requirements of your application. The tag may be
up to eight characters long.
Flow units (PV)
LOI menu path
Basic Setup, Flow Units, PV Units
Traditional Fast Keys
Device dashboard
1,3,1
2,2,1,2
The flow units variable specifies the format in which the flow rate will be displayed. Units should
be selected to meet your particular metering needs. See Table 2-14 for available units of
measure.
Line size
LOI menu path
Basic Setup, Line Size
Traditional Fast Keys
Device dashboard
1,3,1
2,2,1,4,2
The line size (sensor size) must be set to match the actual sensor connected to the transmitter.
The size must be specified in inches. See Table 2-15 for available sensor sizes.
Upper Range Value (URV)
LOI menu path
Basic Setup, PV URV
Traditional Fast Keys
Device dashboard
1,3,1
2,2,1,3,3
The URV sets the 20 mA point for the analog output. This value is typically set to full-scale flow.
The units that appear will be the same as those selected under the flow units parameter. The
URV may be set between –39.3 ft/s to 39.3 ft/s (–12 m/s to 12 m/s). There must be at least 1
ft/s (0.3 m/s) span between the URV and LRV.
34
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Lower Range Value (LRV)
LOI menu path
Basic Setup, PV LRV
Traditional Fast Keys
Device dashboard
1,3,1
2,2,1,3,2
The LRV sets the 4 mA point for the analog output. This value is typically set to zero flow. The
units that appear will be the same as those selected under the flow units parameter. The LRV
may be set between –39.3 ft/s to 39.3 ft/s (–12 m/s to 12 m/s). There must be at least 1 ft/s (0.3
m/s) span between the URV and LRV.
Calibration number
LOI menu path
Basic Setup, Cal Number
Traditional Fast Keys
Device dashboard
1,3,1
2,2,1,4,1
The sensor calibration number is a 16-digit number generated at the Rosemount factory during
flow calibration, is unique to each sensor, and is located on the sensor tag.
PV damping
LOI menu path
Basic Setup, PV Damping
Traditional Fast Keys
Device dashboard
1,3,1
2,2,1,3,4
Primary variable damping allows selection of a response time, in seconds, to a step change in
flow rate. It is most often used to smooth fluctuations in output.
Installation
35
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Table 2-14. Available Flow Units
Volumetric units
Mass units
gal / sec
lbs / sec
gal / min
lbs / min
gal / hr
lbs / hr
gal / day
lbs / day
L / sec
kg / sec
L / min
kg / min
L / hr
kg / hr
L / day
kg / day
ft3 / sec
(s) tons / min
ft3 / min
(s) tons / hr
ft3 / hr
(s) tons / day
ft3 / day
(m) tons / min
cm3 / min
(m) tons / hr
m3 / sec
(m) tons / day
m3 / min
m3 / hr
Velocity units
m3 / day
ft / sec
Impgal / sec
m / sec
Impgal / min
Impgal / hr
Special units
Impgal / day
Special (User Defined)
B42 / sec (1 barrel = 42 gallons)
B42 / min (1 barrel = 42 gallons)
B42 / hr (1 barrel = 42 gallons)
B42 / day (1 barrel = 42 gallons)
B31 / sec (1 barrel = 31 gallons)
B31 / min (1 barrel = 31 gallons)
B31 / hr (1 barrel = 31 gallons)
B31 / day (1 barrel = 31 gallons)
36
Installation
Reference Manual
Section 2: Installation
00809-0100-4444, Rev AD
August 2015
Table 2-15. Available Sensor Sizes
Sensor size
Installation
0.10-in. (2.5 mm)
18-in. (450 mm)
0.15-in. (4 mm)
20-in. (500 mm)
0.25-in. (6 mm)
24-in. (600 mm)
0.30-in. (8 mm)
28-in. (700 mm)
0.50-in. (15 mm)
30-in. (750 mm)
0.75-in. (20 mm)
32-in. (800 mm)
1.0-in. (25 mm)
36-in. (900 mm)
1.5-in. (40 mm)
40-in. (1000 mm)
2.0-in. (50 mm)
42-in. (1050 mm)
2.5-in. (65 mm)
44-in. (1100 mm)
3.0-in. (80 mm)
48-in. (1200 mm)
4.0-in. (100 mm)
54-in. (1350 mm)
5.0-in. (125 mm)
56-in. (1400 mm)
6.0-in. (150 mm)
60-in. (1500 mm)
8.0-in. (200 mm)
64-in. (1600 mm)
10-in. (250 mm)
66-in. (1650 mm)
12-in. (300 mm)
72-in. (1800 mm)
14-in. (350 mm)
78-in. (1950 mm)
16-in. (400 mm)
80-in. (2000 mm)
37
Section 2: Installation
August 2015
38
Reference Manual
00809-0100-4444, Rev AD
Installation
Section 3: Advanced Installation Details
Reference Manual
August 2015
00809-0100-4444, Rev AD
Section 3
Advanced Installation Details
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional loops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connect discrete input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Process reference connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coil housing configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
page 39
page 39
page 39
page 41
page 49
page 50
page 50
Introduction
This section details some of the advanced installation considerations when utilizing the
Rosemount® 8700M Magnetic Flowmeter Platform.
3.2
Safety messages
The electronics may store energy after power is removed. Allow ten minutes for charge to
dissipate prior to removing electronics compartment cover.
Note
The electronics stack is electrostatically sensitive. Be sure to observe handling precautions for
static-sensitive components.
3.3
Hardware switches
The electronics are equipped with four user-selectable hardware switches. These switches set
the Alarm Mode, Internal/External Analog Power, Transmitter Security, and Internal/External
Pulse Power.
Definitions of these switches and their functions are provided below. To change the settings, see
below.
3.3.1
Alarm mode
If an event occurs that would trigger an alarm in the electronics, the analog output will be driven
high or low, depending on the switch position. The switch is set in the HIGH position when
shipped from the factory. Refer to Table 5-1 on page 88 and Table 5-2 on page 88 for analog
output values of the alarm.
Advanced Installation Details
39
Section 3: Advanced Installation Details
3.3.2
Reference Manual
00809-0100-4444, Rev AD
August 2015
Transmitter security
The security switch on the 8732EM allows the user to lock out any configuration changes
attempted on the transmitter. No changes to the configuration are allowed when the switch is
in the ON position. The flow rate indication and totalizer functions remain active at all times.
With the switch in the ON position, access to review the operating parameters is available. No
configuration changes are allowed.
Transmitter security is set in the OFF position when shipped from the factory.
3.3.3
Internal/external analog power
The 8732EM 4-20 mA loop may be powered internally or by an external power supply. The
internal /external power supply switch determines the source of the 4-20 mA loop power.
Transmitters are shipped from the factory with the switch set in the INTERNAL position.
The external power option is required for multidrop configurations. A 10-30 VDC external
supply is required and the 4-20 mA power switch must be set to the EXTERNAL position. For
further information on 4-20 mA external power, see “Analog output” on page 29.
3.3.4
Internal/external pulse power
The 8732EM pulse loop may be powered internally or by an external power supply. The internal/external power supply switch determines the source of the pulse loop power.
Transmitters are shipped from the factory with the switch set in the EXTERNAL position.
A 5-28 VDC external supply is required when the pulse power switch is set to the EXTERNAL
position. For further information on the pulse external power, see “Connect pulse output” on
page 41.
3.3.5
Changing hardware switch settings
To change the switch settings, complete the steps below:
Note
The hardware switches are located on the top side of the electronics board and changing their
settings requires opening the electronics housing. If possible, carry out these procedures away
from the plant environment in order to protect the electronics.
40
1.
Place the control loop into manual control.
2.
Disconnect power to the transmitter
3.
Remove the electronics compartment cover. If the cover has a cover jam screw, this
must be loosened prior to removal of the cover.
4.
Remove the LOI, if applicable.
5.
Identify the location of each switch (see Figure 3-1).
Advanced Installation Details
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
August 2015
6.
Change the setting of the desired switches with a small, non-metallic tool.
7.
Replace the LOI if applicable, and the electronics compartment cover. If the cover has a
cover jam screw, this must be tightened to comply with installation requirements. See
“Cover jam screw” on page 33 for details on the cover jam screw.
8.
Return power to the transmitter and verify the flow measurement is correct.
9.
Return the control loop to automatic control.
Figure 3-1. Rosemount 8732EM Electronics Stack and Hardware Switches
3.4
Additional loops
There are three additional loop connections available on the 8732EM Transmitter:
3.4.1

Pulse output - used for external or remote totalization.

Channel 1 can be configured as discrete input or discrete output.

Channel 2 can be configured as discrete output only.
Connect pulse output
The pulse output function provides a galvanically isolated frequency signal that is proportional
to the flow through the sensor. The signal is typically used in conjunction with an external
totalizer or control system. The default position of the internal/external pulse power switch is in
the EXTERNAL position. The user-selectable power switch is located on the electronics board.
Advanced Installation Details
41
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
August 2015
External
For transmitters with the internal/external pulse power switch (output option code A) set in the
EXTERNAL position or transmitters with intrinsically safe outputs (output option code B) the
following requirements apply:
Supply voltage: 5 to 28 VDC
Maximum current: 100 mA
Maximum power: 1.0 W
Load resistance: 200 to 10k Ohms (typical value 1k Ohms)
Output option
code
Supply voltage
Resistance vs cable length
A
5-28 VDC
See Figure 3-2 on page 43
B
5 VDC
See Figure 3-3 on page 43
B
12 VDC
See Figure 3-4 on page 44
B
24 VDC
See Figure 3-5 on page 44
Pulse mode: Fixed pulse width or 50% duty cycle
Pulse duration: 0.1 to 650 ms (adjustable)
Maximum pulse frequency: Output option code A is 10,000 Hz
Maximum pulse frequency: Output option code B is 5000 Hz
FET switch closure: solid state switch
42
Advanced Installation Details
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
August 2015
Figure 3-2. Output Option Code A—Maximum Frequency vs. Cable Length
Figure 3-3. Output Option Code B—5 VDC Supply
At 5000 Hz operation with a 5 VDC supply, pull-up resistances of 200 to 1000 Ohms allow
cable lengths up to 660 ft (200 m).
Advanced Installation Details
43
Section 3: Advanced Installation Details
Reference Manual
00809-0100-4444, Rev AD
August 2015
Figure 3-4. Output Option Code B—2 VDC Supply
At 5000 Hz operation with a 12 VDC supply, pull-up resistances of 500 to 2500 Ohms allow
cable lengths up to 660 ft (200 m). Resistances from 500 to 1000 Ohms allow a cable
length of 1000 ft (330 m).
Figure 3-5. Output Option Code B—24 VDC Supply
At 5000 Hz operation with a 24 VDC supply, pull-up resistances of 1000 to 10,000 Ohms
allow cable lengths up to 660 ft (200 m). Resistances from 1000 to 2500 Ohms allow a
cable length of 1000 ft (330 m).
44
Advanced Installation Details
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
August 2015
Complete the following steps to connect an external power supply.
1.
Ensure the power source and connecting cable meet the requirements outlined
previously.
2.
Turn off the transmitter and pulse output power sources.
3.
Run the power cable to the transmitter.
4.
Connect - DC to terminal 3.
5.
Connect + DC to terminal 4.
Refer to Figure 3-6 and Figure 3-7.
Figure 3-6. Connecting an Electromechanical Totalizer/Counter with External Power
Supply
Schematic showing
FET between
terminal 3 and 4
5-24 V DC
Power Supply
Electro-mechanical
Counter
Note
Total loop impedance must be sufficient to keep loop current below maximum rating. A resistor
can be added in the loop to raise impedance.
Advanced Installation Details
45
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
August 2015
Figure 3-7. Connecting to an Electronic Totalizer/Counter with External Power Supply
Schematic showing
FET between
terminal 3 and 4
Electronic
Counter
5-24 V DC
Power Supply
Note
Total loop impedance must be sufficient to keep loop current below maximum rating.
46
Advanced Installation Details
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
August 2015
Internal
When the pulse switch is set to internal, the pulse loop will be powered from the transmitter.
Supply voltage from the transmitter can be up to 12 VDC. Refer to Figure 3-8 and connect the
transmitter directly to the counter. Internal pulse power can only be used with an electronic
totalizer or counter and cannot be used with an electromechanical counter.
1.
Turn off the transmitter.
2.
Connect - DC to terminal 3.
3.
Connect + DC to terminal 4.
Figure 3-8. Connecting to an Electronic Totalizer / Counter with Internal Power Supply
Schematic showing
FET between
terminal 3 and 4
Electronic
Counter
Advanced Installation Details
47
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
August 2015
3.4.2
Connect discrete output
The discrete output control function can be configured to drive an external signal to indicate
zero flow, reverse flow, empty pipe, diagnostic status, flow limit, or transmitter status. The
following requirements apply:
Supply Voltage: 5 to 28 VDC
Maximum Voltage: 28 VDC at 240 mA
Switch Closure: solid state relay
For discrete output control, connect the power source and control relay to the transmitter. To
connect external power for discrete output control, complete the following steps:
1.
Ensure the power source and connecting cable meet the requirements outlined
previously.
2.
Turn off the transmitter and discrete power sources.
3.
Run the power cable to the transmitter.
4.
Channel 1: Connect -DC to terminal 5, connect +DC to terminal 6.
5.
Channel 2: Connect -DC to terminal 7, connect +DC to terminal 8.
Refer to Figure 3-9 and Figure 3.5.
Figure 3-9. Connect Discrete Output to Relay or Control System Input
Control Relay
or Input
5-28 V DC
Power Supply
Note
Total loop impedance must be sufficient to keep loop current below maximum rating. A resistor
can be added in the loop to raise impedance.
48
Advanced Installation Details
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
3.4.3
August 2015
Connect discrete input
The discrete input can provide positive zero return (PZR) or net totalizer reset. The following
requirements apply:
Supply Voltage: 5 to 28 VDC
Control Current: 1.5 - 20mA
Input Impedance: 2.5 k Ω plus 1.2V Diode drop. See Figure 3-11.
To connect the discrete input, complete the following steps.
1.
Ensure the power source and connecting cable meet the requirements outlined
previously.
2.
Turn off the transmitter and discrete power sources.
3.
Run the power cable to the transmitter.
4.
Connect -DC to terminal 5.
5.
Connect +DC to terminal 6.
Refer to Figure 3-10 and Figure 3-11.
Figure 3-10. Connecting Discrete Input
Relay Contact or Control
System Output
5-28 V DC
Power Supply
Advanced Installation Details
49
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
August 2015
Figure 3-11. Discrete Input Operating Range
30
25
Supply Voltage
Digital Input Operating Range
20
15
10
5
0
0
2.5
5
7.5
10
12.5
15
Series Resistance Ωin + Ωext (Kohms)
3.5
Process reference connection
Establishing a process reference for the sensor is one of the most important details of sensor
installation. Proper process reference creates the lowest noise environment for the transmitter
to make a stable reading. Refer to Table 2-10 on page 20 to determine which option to follow for
proper installation.
Note
Consult factory for installations requiring cathodic protection or situations where there are high
electrical currents or high electrical potentials present in the process.
3.6
Coil housing configuration
The coil housing provides physical protection of the coils and other internal components from
contamination and physical damage that might occur in an industrial environment. The coil
housing is an all-welded and gasket-free design.
The 8705 model is available in four coil housing configurations. Configurations are identified by
the M0, M1, M2, or M4 options codes found in the model number. The 8711 and 8721 models
are only available in one coil housing coil configuration; a separate option code is not available.
50
Advanced Installation Details
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
3.6.1
August 2015
Standard coil housing configuration
The standard coil housing configuration is a factory sealed all-welded enclosure and is available
for the following models (see Figure 3-12):

8705 with option code M0 - 8705xxxxxxxxM0

8711 with option code M/L - 8711xxxxxxM/L

8721 with option code R/U - 8721xxxxxxR/U
Figure 3-12. Standard Housing Configuration (8705 Shown)
Advanced Installation Details
51
Section 3: Advanced Installation Details
3.6.2
Reference Manual
00809-0100-4444, Rev AD
August 2015
Process leak protection (option M1)
The 8705 is available with process leak detection through the use of a threaded connection and
pressure relief valve (PRV). This coil housing configuration is a factory sealed all-welded
enclosure. The M1 configuration is available for the 8705 only.

8705 with option code M1 - 8705xxxxxxxxM1
A PRV can be installed in the threaded connection to prevent possible over-pressuring of the coil
housing caused by a primary seal failure. The PRV is capable of venting fugitive emissions when
pressure inside the coil housing exceeds five psi. Additional piping may be connected to the PRV
to drain any process leakage to a safe location (see Figure 3-13).
In the event of a primary seal failure, this configuration will not protect the coils or other internal
components of the sensor from exposure to the process fluid.
Note
The PRV is supplied with the meter to be installed by the customer. Installation of the PRV and
any associated piping must be performed in accordance with environmental and hazardous area
requirements.
Figure 3-13. 8705 with M1 Coil Housing Configuration and PRV
52
Advanced Installation Details
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
3.6.3
August 2015
Process leak containment (Option M2 or M4)
The 8705 is available with process leak containment. The coil housing configuration is a factory
sealed all-welded enclosure with the addition of sealed electrode compartments. The M2/M4
configuration is available for the 8705 only.

8705 with option code M2/M4 - 8705xxxxxxxxM2/M4
This configuration divides the coil housing into separate compartments, one for each electrode
and one for the coils. In the event of a primary seal failure, the fluid is contained in the electrode
compartment. The sealed electrode compartment prevents the process fluid from entering the
coil compartment where it may damage the coils and other internal components. The electrode
compartments are designed to contain the process fluid up to a maximum pressure of 740 psig.

Code M2 - sealed, welded coil housing with separate sealed and welded electrode
compartments (see Figure 3-14).

Code M4 - sealed, welded coil housing with separate sealed and welded electrode
compartments with a threaded port on the electrode tunnel cap, capable of venting
fugitive emissions (see Figure 3-15).
Note
To properly vent process fluid from the electrode compartment to a safe location, additional
piping is required and must be installed by the user. Installation of any associated piping must be
performed in accordance with environmental and hazardous area requirements. In the event of
primary seal failure, the electrode compartment may be pressurized. Use caution when
removing the cap screw.
Figure 3-14. 8705 with M2 Coil Housing Configuration
Advanced Installation Details
53
Section 3: Advanced Installation Details
Reference Manual
00809-0100-4444, Rev AD
August 2015
Figure 3-15. 8705 with M4 Coil Housing Configuration
3.6.4
Higher temperature applications and sensor insulation
best practices
Insulation of the magnetic flowmeter sensor is not typically recommended. However, in
applications with higher temperature process fluids (above 150°F / 65°C), plant safety, sensor
reliability, and sensor longevity can be improved with careful attention to proper insulation.
1.
54
In applications where process fluid permeation of the liner has been observed or may
be expected, the rate of permeation can be reduced by decreasing the temperature
gradient between the process fluid and the outside of the meter body. In these
applications only the space between the process flanges and the coil housing should
be insulated (see Figure 3-16).
Advanced Installation Details
Reference Manual
Section 3: Advanced Installation Details
00809-0100-4444, Rev AD
August 2015
Figure 3-16. Insulating a Rosemount Magnetic Flowmeter for Permeation
2.
Advanced Installation Details
When insulation of the magnetic flowmeter sensor is required due to plant safety
standards designed to protect personnel from contact burns, extend the insulation up
to the coil housing, covering both ends of the sensor and flanges (Figure 3-17). The
insulation should NOT cover the coil housing or the terminal junction box. Insulating
the coil housing and the terminal junction box can result in overheating of the coil
compartment and terminals, resulting in erratic/erroneous flow readings and potential
damage or failure of the meter.
55
Section 3: Advanced Installation Details
August 2015
Reference Manual
00809-0100-4444, Rev AD
Figure 3-17. Insulating a Rosemount Magnetic Flowmeter for Safety/Plant Standards
56
Advanced Installation Details
Section 4: Operation
Reference Manual
August 2015
00809-0100-4444, Rev AD
Section 4
Operation
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 57
Local operator interface (LOI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 57
Field Communicator interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 64
Process variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 85
4.1
Introduction
The 8732EM transmitter features a full range of software functions, transmitter configurations,
and diagnostic settings. These features can be accessed through the Local Operator Interface
(LOI), a handheld Field Communicator, AMS® Device Manager, or a host control system.
Configuration variables may be changed at any time; specific instructions are provided through
on-screen instructions.
This section covers the basic features of the LOI (optional) and provides general instructions on
how to navigate the configuration menus using the optical buttons. The section also covers the
use of a Field Communicator and provides menu trees to access each function.
For detailed LOI configuration refer to Section 5: Advanced Configuration Functionality.
4.2
Local operator interface (LOI)
The optional LOI provides a communications center for the 8732EM.
The LOI allows an operator to:
4.2.1

Change transmitter configuration

View flow and totalizer values

Start/stop and reset totalizer values

Run diagnostics and view the results

Monitor transmitter status

Other functions
Basic features
The basic features of the LOI include a display window and four navigational arrow keys (see
Figure 4-1).
To activate the LOI, press the DOWN arrow two times. Use the UP, DOWN, LEFT, and RIGHT
arrows to navigate the menu structure. A map of the LOI menu structure is shown on Figure 4-2
and Figure 4-3.
Operation
57
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Figure 4-1. Local Operator Interface Keypad and Character Display
4.2.2
Data entry
The LOI keypad does not have alphanumeric keys. Alphanumeric and symbolic data is entered
by the following procedure. Use the steps below to access the appropriate functions.
58
1.
Use the arrow keys to navigate the menu structure (Figure 4-2 and Figure 4-3) in order
to access the appropriate alphanumeric parameter.
2.
Use the UP, DOWN or RIGHT arrow key to begin editing the parameter. (Use the LEFT
arrow key to go back without changing the value).
For numerical data, toggle through the digits 0-9, decimal point, and dash. For
alphabetical data, toggle through the letters of the alphabet A-Z, digits 0-9, and the
symbols ?, &, +, -, *, /, $, @,%, and the blank space.
3.
Use the RIGHT arrow key to highlight each character you want to change and then use
the UP or DOWN arrow keys to select the value. If you go past a character that you wish
to change, keep using the RIGHT arrow key to wrap around in order to arrive at the
character you want to change.
4.
Press “E” (the LEFT arrow key) when all changes are complete to save the entered
values. Press the LEFT arrow key again to navigate back to the menu tree.
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
4.2.3
August 2015
Data entry examples
Press the DOWN arrow key twice to access the menu structures shown in Figure 4-2 and
Figure 4-3. Use the arrow keys to navigate to the desired parameters to review/change.
Parameter values are classified as table values or select values. Table values are available from a
predefined list. For parameters such as line size or flow units. Select values are integers. floating
point numbers, or character strings and are entered one character at a time using the arrow
keys for parameters such as PV URV and calibration number.
Table value example
Setting the sensor size:
1.
Press the DOWN arrow key twice to access the menu. See Figure 4-2.
2.
Using the arrow keys, select line size from the basic setup menu.
3.
Press the UP/DOWN arrow to increase/decrease the sensor size to the next value.
4.
When you reach the desired sensor size, press “E” (the left arrow).
5.
Set the loop to manual if necessary, and press “E” again.
After a moment, the LOI will display VALUE STORED SUCCESSFULLY and then display the
selected value.
Select value example
Changing the upper range limit:
1.
Press the DOWN arrow key twice to access the menu. See Figure 4-2.
2.
Using the arrow keys, select PV URV from the basic setup menu.
3.
Press RIGHT arrow key to position the cursor.
4.
Press UP or DOWN to set the number.
5.
Repeat steps 3and 4 until desired number is displayed, press “E” (the left arrow).
6.
Set the loop to manual if necessary, and press “E” again.
After a moment, the LOI will display VALUE STORED SUCCESSFULLY and then display the
selected value.
4.2.4
Totalizer functionality
Start totalizer
To start the totalizer, press the DOWN arrow to display the totalizer screen and press “E” to
begin totalization. A symbol will flash in the lower right hand corner indicating that the meter is
totalizing.
Operation
59
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Pause totalizer
To pause the totalizer, press the DOWN arrow to display the totalizer screen and press the
RIGHT arrow to pause the totalizer. This will hold the current totalizer values on the screen for
reading or recording. The totalizer will continue to run even though the values are not changing.
To unpause the totalizer, press the RIGHT arrow again. The totalizer value will instantly
increment to the correct value and continuing running.
Stop totalizer
To stop the totalizer, press the DOWN arrow to display the totalizer screen and press “E” to end
totalization. The flashing symbol will no longer display in the lower right hand corner indicating
that the meter has stopped totalizing.
Reset totalizer
To reset the totalizer, press the DOWN arrow to display the totalizer screen and follow the
procedure above to stop totalization. Once totalization has stopped, press the RIGHT arrow key
to reset the NET total value to zero. To reset the GROSS, FORWARD, and REVERSE total values,
you must change the line size. See “Basic configuration” on page 34 for details on how to
change the line size.
4.2.5
Display lock
The 8732EM transmitter has display lock functionality to prevent unintentional configuration
changes. The display can be locked manually or configured to automatically lock after a set
period of time.
Manual display lock
To activate hold the UP arrow for 3 seconds and then following the on-screen instructions.
When the display lock is activated, a lock symbol will appear in the lower right hand corner of
the display. To deactivate the display lock, hold the UP arrow for 3 seconds and follow the
on-screen instructions. Once deactivated, the lock symbol will no longer appear in the lower
right hand corner of the display.
Auto display lock
1.
Press the DOWN arrow key twice to access the menu. See Table 4-2.
2.
Using the arrow keys, select LOI config from the Detailed Setup menu.
3.
Press DOWN arrow to highlight disp auto lock and press the RIGHT arrow to enter the
menu.
4.
Press DOWN arrow to select the auto lock time.
5.
When you reach the desired time, press “E” (the left arrow).
6.
Set the loop to manual if necessary, and press “E” again.
After a moment, the LOI will display VALUE STORED SUCCESSFULLY and then display the
selected value.
60
Operation
Reference Manual
00809-0100-4444, Rev AD
4.2.6
Section 4: Operation
August 2015
Diagnostic messages
Diagnostic messages may appear on the LOI. See Table 6-1 on page 111, Table 6-2 on page 126,
and Table 6-3 on page 127 for a complete list of messages, potential causes, and corrective
actions for these messages.
4.2.7
Display symbols
When certain transmitter functions are active, a symbol will appear in the lower-right corner of
the display. The possible symbols include the following:
Display Lock
Totalizer
Reverse flow
Continuous meter verification
Operation
61
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Figure 4-2. Local Operator Interface (LOI) Menu Tree (Diagnostics and Basic Setup)
Diagnostics
Basic Setup
Detailed Setup
Diag Controls
Basic Diag
Advanced Diag
Variables
Trims
Status
Empty Pipe
Process Noise
Ground/Wiring
Elec Coating
Elect Temp
Reverse Flow
Cont Meter Ver
Coils
Electrodes
Transmitter
Analog Output
EP Control
EP Value
EP Trig Level
EP Counts
Self Test
AO Loop Test
Pulse Out Test
Empty Pipe
Elect Temp
Flow Limit 1
Flow Limit 2
Total Limit
Control 1
Mode 1
High Limit 1
Low Limit 1
Hysteresis
Control 2
Mode 2
High Limit 2
Low Limit 2
Hysteresis
Total Control
Total Mode
Tot Hi Limit
Tot Low Limit
Hysteresis
Ground/Wiring
Process Noise
Elec Coating
Meter Verify
4-20 mA Verify
Licensing
EC Current Val
EC Limit 1
EC Limit 2
EC Max Value
Reset Max Val
Run Meter Ver
View Results
Sensr Baseline
Test Criteria
Measurements
Empty Pipe
Elect Temp
Line Noise
5Hz SNR
37Hz SNR
Elec Coating
Signal Power
37Hz Auto Zero
Coil Current
MV Results
D/A Trim
Digital Trim
37Hz Auto Zero
Universal Trim
Tag
Flow Units
Line Size
PV URV
PV LRV
Cal Number
PV Damping
PV Units
Special Units
Totalize Units
Test Condition
Test Criteria
MV Results
Sim Velocity
ActualVelocity
Flow Sim Dev
Xmtr Cal Verify
Sensor Cal Dev
Sensor Cal
Coil Circuit
Electrode Ckt
Manual Results
Continual Res
Valves
Reset Baseline
Recall Values
No Flow
Flowing, Full
Empty Pipe
Continual
Test Criteria
Sim Velocity
ActualVelocity
Flow Sim Dev
Coil Inductnce
Sensor Cal Dev
Coil Resist
Electrode Res
4-20 mA Expect
4-20 mA Actual
1AO FB Dev
Manual Measure
Continual Meas
Coil Resist
Coil Inductnce
Electrode Res
4-20mA Verify
View Results
Process Noise
Ground/Wiring
Elec Coating
Meter Verif
DI/DO
Coil Resist
Coil Inductnce
Actual Velocity
Electrode Res
License Status
License Key
Device ID
Software Rev
License Key
EC Current Val
EC Max Value
Manual Results
Continual Results
Test Condition
Test Criteria
MV Results
Sim Velocity
ActualVelocity
Flow Sim Dev
Xmtr Cal Verify
Sensor Cal Dev
Sensor Cal
Coil Circuit
Electrode Ckt
Coil Resist
Coil Signature
Electrode Res
ActualVelocity
Flow Sim Dev
4-20 mA Expect
4-20 mA Actual
AO FB Dev
Test Criteria
Sim Velocity
ActualVelocity
Flow Sim Dev
Coil Inductnce
Sensor Cal Dev
Coil Resist
Electrode Res
4-20 mA Expect
4-20 mA Actual
AO FB Dev
Detailed Setup
see Figure 4-3 on next page
62
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Figure 4-3. Local Operator Interface (LOI) Menu Tree (Detailed Setup)
Diagnostics
Basic Setup
Detailed Setup
More Params
Output Config
LOI Config
Sig Processing
Device Info
Coil Frequency
Proc Density
PV USL
PV LSL
PV Min Span
Analog
Pulse
DI/DO Config
Totalizer
Reverse Flow
Alarm level
HART
PV URV
PV LRV
PV AO
Alarm Type
Test
Alarm Level
AO Diag Alarm
Pulse Scaling
Pulse Width
Pulse Mode
Test
DI/O 1
DO 2
Flow Limit 1
Flow Limit 2
Total Limit
Diag Alert
Empty Pipe
Process Noise
Ground/Wiring
Elec Coating
Elect Temp
Reverse Flow
Flow Limit 1
Flow Limit 2
Total Limit
Cont Meter Ver
DI/O 1 Control
DI 1
DO 1
Input
Output
N/A
Reverse Flow
Zero Flow
XMTR Fault
Empty Pipe
Flow Limit 1
Flow Limit 2
Diag Alert
Total Limit 1
Control 1
Mode 1
High Limit 1
Low Limit 1
Hysteresis
Control 2
Mode 2
High Limit 2
Low Limit 2
Hysteresis
Totalizer Units
Total Display
Flow Display
Total Display
Language
LOI Err Mask
Disp Auto Lock
Operating Mode
SP Config
Coil Frequency
PV Damping
Lo-Flow Cutoff
Tag
Description
Message
Device ID
PV Sensor S/N
Sensor Tag
Write Protect
Revision Num
Operation
Variable Map
Poll Address
Req Preams
Resp Preams
Burse Mode
Burst Command
SP Control
Samples
% Rate
Time Limit
Total Control
Total Mode
Tot Hi Limit
Tot Low Limit
Hysteresis
Elec Failure
Coil Open Ckt
Empty Pipe
Reverse Flow
Ground/Wiring
Process Noise
Elect Temp
Elec Coat 1
Elec Coat 2
Cont Meter Ver
Coil Over Curr
Sensr Elec Sat
Coil Power Lim
PV
SV
TV
QV
Software Rev
Final Asmbl #
63
Section 4: Operation
4.3
Reference Manual
00809-0100-4444, Rev AD
August 2015
Field Communicator interface
The 8732EM transmitter can be configured with a Field Communicator using HART® Protocol
gaining access to the software functions, transmitter configurations, and diagnostic settings. Refer
to the Field Communicator Manual for detailed instructions on how to connect to the device.
4.3.1
Field Communicator user interface
The 8732E device driver uses conditional formatting menus. If the diagnostic is not active, the
diagnostic will not be displayed as a menu item in the Field Communicator. The Fast Key sequence
and menu trees will be resequenced accordingly.
There are two styles of interface available for Field Communicators. The traditional interface is
shown in Figure 4-4. The device dashboard interface is shown in Figure 4-5.
Figure 4-4. Traditional Interface
The traditional interface Fast Keys are located in Table 4-1 on page 65. The corresponding menu
trees are located Figure 4-6 on page 81 and Figure 4-7 on page 82.
64
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Figure 4-5. Device Dashboard Interface
The device dashboard interface Fast Keys are located in Table 4-2 on page 74. The corresponding
menu tree is located Figure 4-8 on page 83 and Figure 4-9 on page 84.
Table 4-1. Traditional Field Communicator Fast Keys
Operation
Function
Traditional Fast Keys
Process variables
1, 1
Primary Variable (PV)
1, 1, 1
PV Percent of Range (PV % rnge)
1, 1, 2
PV Analog Output (AO) (PV Loop current)
1, 1, 3
Totalizer Setup
1, 1, 4
Totalizer Units
1, 1, 4, 1
Gross Total
1, 1, 4, 2
Net Total
1, 1, 4, 3
Reverse Total
1, 1, 4, 4
Start Totalizer
1, 1, 4, 5
Stop Totalizer
1, 1, 4, 6
Reset Totalizer
1, 1, 4, 7
Pulse Output
1, 1, 5
Diagnostics
1, 2
Diag Controls
1, 2, 1
Diagnostic Controls
1, 2, 1, 1
Empty Pipe
1, 2, 1, 1, --(1)
Process Noise
1, 2, 1, 1, --(1)
Grounding/Wiring
1, 2, 1, 1, --(1)
Electrode Coating
1, 2, 1, 1, --(1)
65
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-1. Traditional Field Communicator Fast Keys (continued)
66
Function
Traditional Fast Keys
Electronics Temp
1, 2, 1, 1, --(1)
Reverse Flow
1, 2, 1, 2
Continual Ver.
1, 2, 1, 3
Coils
1, 2, 1, 3, 1 --(1)
Electrodes
1, 2, 1, 3, 2 --(1)
Transmitter
1, 2, 1, 3, 3 --(1)
Analog Output
1, 2, 1, 3, 4 --(1)
Basic Diagnostics
1, 2, 2
Self Test
1, 2, 2, 1
AO Loop Test
1, 2, 2, 2
4 mA
1, 2, 2, 2, 1
20 mA
1, 2, 2, 2, 2
Simulate Alarm
1, 2, 2, 2, 3
Other
1, 2, 2, 2, 4
End
1, 2, 2, 2, 5
Pulse Output Loop Test
1, 2, 2, 3
Tune Empty Pipe
1, 2, 2, 4
EP Value
1, 2, 2, 4, 1
EP Trig. Level
1, 2, 2, 4, 2
EP Counts
1, 2, 2, 4, 3
Electronics Temp
1, 2, 2, 5
Flow Limit 1
1, 2, 2, 6
Control 1
1, 2, 2, 6, 1
Mode 1
1, 2, 2, 6, 2
High Limit 1
1, 2, 2, 6, 3
Low Limit 1
1, 2, 2, 6, 4
Flow Limit Hysteresis
1, 2, 2, 6, 5
Flow Limit 2
1, 2, 2, 7
Control 2
1, 2, 2, 7, 1
Mode 2
1, 2, 2, 7, 2
High Limit 2
1, 2, 2, 7, 3
Low Limit 2
1, 2, 2, 7, 4
Flow Limit Hysteresis
1, 2, 2, 7, 5
Total Limit
1, 2, 2, 8
Total Control
1, 2, 2, 8, 1
Total Mode
1, 2, 2, 8, 2
Total High Limit
1, 2, 2, 8, 3
Total Low Limit
1, 2, 2, 8, 4
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-1. Traditional Field Communicator Fast Keys (continued)
Function
Traditional Fast Keys
Total Limit Hysteresis
1, 2, 2, 8, 5
Advanced Diagnostics
1, 2, 3
Electrode Coat
1, 2, 3, 1
EC Value
1, 2, 3, 1, 1
EC Level 1 Limit
1, 2, 3, 1, 2
EC Level 2 Limit
1, 2, 3, 1, 3
Max EC Value
1, 2, 3, 1, 4
Clear Max Electrode
1, 2, 3, 1, 5
8714i Cal Verification
1, 2, 3, 2
Run 8714i Cal Verification
1, 2, 3, 2, 1
View Results
1, 2, 3, 2, 2
Manual Results
1, 2, 3, 2, 2, 1
Test Condition
1, 2, 3, 2, 2, 1, 1
Test Criteria
1, 2, 3, 2, 2, 1, 2
8714i Test Result
1, 2, 3, 2, 2, 1, 3
Simulated Velocity
1, 2, 3, 2, 2, 1, 4
Actual Velocity
1, 2, 3, 2, 2, 1, 5
Velocity Deviation
1, 2, 3, 2, 2, 1, 6
Xmter Cal Test Result
1, 2, 3, 2, 2, 1, 7
Sensor Cal Deviation
1, 2, 3, 2, 2, 1, 8
Sensor Cal Test Result
1, 2, 3, 2, 2, 1, 9
Coil Circuit Test Result
1, 2, 3, 2, 2, 1, 10(2)
Electrode Circuit Test Result(2)
1, 2, 3, 2, 2, 1, 11(2)
Continual Results
1, 2, 3, 2, 2, 2
Continuous Limit
1, 2, 3, 2, 2, 2, 1
Simulated Velocity
1, 2, 3, 2, 2, 2, 2
Actual Velocity
1, 2, 3, 2, 2, 2, 3
Velocity Deviation
1, 2, 3, 2, 2, 2, 4
Coil Signature
1, 2, 3, 2, 2, 2, 5
Sensor Cal Deviation
1, 2, 3, 2, 2, 2, 6
Coil Resistance
1, 2, 3, 2, 2, 2, 7
Electrode Resistance
1, 2, 3, 2, 2, 2, 8
mA Expected
1, 2, 3, 2, 2, 2, 9
(2)
mA Actual
Operation
(2)
1, 2, 3, 2, 2, 2, 10(2)
mA Deviation(2)
1, 2, 3, 2, 2, 2, 11(2)
Sensor Signature
1, 2, 3, 2, 3
Signature Values
1, 2, 3, 2, 3, 1
67
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-1. Traditional Field Communicator Fast Keys (continued)
68
Function
Traditional Fast Keys
Coil Resistance
1, 2, 3, 2, 3, 1, 1
Coil Signature
1, 2, 3, 2, 3, 1, 2
Electrode Resistance
1, 2, 3, 2, 3, 1, 3
Re-Signature Meter
1, 2, 3, 2, 3, 2
Recall Last Saved Values
1, 2, 3, 2, 3, 3
Set Pass/Fail Criteria
1, 2, 3, 2, 4
No Flow Limit
1, 2, 3, 2, 4, 1
Flowing Limit
1, 2, 3, 2, 4, 2
Empty Pipe Limit
1, 2, 3, 2, 4, 3
Continuous Limit
1, 2, 3, 2, 4, 4
Measurements
1, 2, 3, 2, 5
Manual Measurements
1, 2, 3, 2, 5, 1
Coil Resistance
1, 2, 3, 2, 5, 1, 1
Coil Signature
1, 2, 3, 2, 5, 1, 2
Electrode Resistance
1, 2, 3, 2, 5, 1, 3
Continual Measurements
1, 2, 3, 2, 5, 2
Coil Resistance
1, 2, 3, 2, 5, 2, 1
Coil Signature
1, 2, 3, 2, 5, 2, 2
Electrode Resistance
1, 2, 3, 2, 5, 2, 3
Actual Velocity
1, 2, 3, 2, 5, 2, 4
mA Expected
1, 2, 3, 2, 5, 2, 5
mA Actual
1, 2, 3, 2, 5, 2, 6
4-20 mA Verify
1, 2, 3, 3
4-20 mA Verification
1, 2, 3, 3, 1
View Results
1, 2, 3, 3, 2
Licensing
1, 2, 3, 4
License Status
1, 2, 3, 4, 1
Process Noise Detect
1, 2, 3, 4, 1, 1 --(1)
Line Noise Detection
1, 2, 3, 4, 1, 2 --(1)
Electrode Coating
1, 2, 3, 4, 1, 3 --(1)
8714i
1, 2, 3, 4, 1, 4 --(1)
Digital I/O
1, 2, 3, 4, 1, 5 --(1)
License Key
1, 2, 3, 4, 2
Device ID
1, 2, 3, 4, 2, 1
License Key
1, 2, 3, 4, 2, 2
Diagnostic Variables
1, 2, 4
EP Value
1, 2, 4, 1
Electronics Temp
1, 2, 4, 2
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-1. Traditional Field Communicator Fast Keys (continued)
Operation
Function
Traditional Fast Keys
Line Noise
1, 2, 4, 3
5 Hz SNR
1, 2, 4, 4
37 Hz SNR
1, 2, 4, 5
Electrode Coat
1, 2, 4, 6
EC Value
1, 2, 4, 6, 1
Max EC Value
1, 2, 4, 6, 2
Sig Power
1, 2, 4, 7
8714i Results
1, 2, 4, 8
Manual Results
1, 2, 4, 8, 1
Test Condition
1, 2, 4, 8, 1, 1
Test Criteria
1, 2, 4, 8, 1, 2
8714i Test Result
1, 2, 4, 8, 1, 3
Simulated Velocity
1, 2, 4, 8, 1, 4
Actual Velocity
1, 2, 4, 8, 1, 5
Velocity Deviation
1, 2, 4, 8, 1, 6
Xmtr Cal Test Result
1, 2, 4, 8, 1, 7
Sensor Cal Deviation
1, 2, 4, 8, 1, 8
Sensor Cal Test Result
1, 2, 4, 8, 1, 9
Coil Circuit Test Result
1, 2, 4, 8, 1, 10(2)
Electrode Circuit Test Result
1, 2, 4, 8, 1, 11(2)
Continual Results
1, 2, 4, 8, 2
Continuous Limit
1, 2, 4, 8, 2, 1
Simulated Velocity
1, 2, 4, 8, 2, 2
Actual Velocity
1, 2, 4, 8, 2, 3
Velocity Deviation
1, 2, 4, 8, 2, 4
Coil Signature
1, 2, 4, 8, 2, 5
Sensor Cal Deviation
1, 2, 4, 8, 2, 6
Coil Resistance
1, 2, 4, 8, 2, 7
Electrode Resistance
1, 2, 4, 8, 2, 8
mA Expected
1, 2, 4, 8, 2, 9
mA Actual
1, 2, 4, 8, 2, 10(2)
mA Deviation
1, 2, 4, 8, 2, 11(2)
Auto Zero Offset
1, 2, 4, 9
Trims
1, 2, 5
D/A Trim
1, 2, 5, 1
Scaled D/A Trim
1, 2, 5, 2
Digital Trim
1, 2, 5, 3
69
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-1. Traditional Field Communicator Fast Keys (continued)
70
Function
Traditional Fast Keys
Auto Zero
1, 2, 5, 4
Universal Trim
1, 2, 5, 5
View Status
1, 2, 6
Basic setup
1, 3
Tag
1, 3, 1
Flow Units
1, 3, 2
PV Units
1, 3, 2, 1
Special Units
1, 3, 2, 2
Volume Unit
1, 3, 2, 2, 1
Base Volume Unit
1, 3, 2, 2, 2
Conversion Number
1, 3, 2, 2, 3
Base Time Unit
1, 3, 2, 2, 4
Flow Rate Unit
1, 3, 2, 2, 5
Line Size
1, 3, 3
PV URV
1, 3, 4
PV LRV
1, 3, 5
Calibration Number
1, 3, 6
PV Damping
1, 3, 7
Detailed setup
1, 4
Additional Parameters
1, 4, 1
Coil Drive Frequency
1, 4, 1, 1
Density Value
1, 4, 1, 2
PV USL
1, 4, 1, 3
PV LSL
1, 4, 1, 4
PV Minimum Span
1, 4, 1, 5
Configure Output
1, 4, 2
Analog Output
1, 4, 2, 1
PV URV
1, 4, 2, 1, 1
PV LRV
1, 4, 2, 1, 2
PV Loop Current
1, 4, 2, 1, 3
AO Alarm Type (PV Alrm typ)
1, 4, 2, 1, 4
AO Loop Test
1, 4, 2, 1, 5
D/A Trim
1, 4, 2, 1, 6
Scaled D/A Trim
1, 4, 2, 1, 7
Alarm Level
1, 4, 2, 1, 8
AO Diagnostic Alarm
1, 4, 2, 1, 9
Empty Pipe
1, 4, 2, 1, 9, 1 --(1)
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-1. Traditional Field Communicator Fast Keys (continued)
Operation
Function
Traditional Fast Keys
Reverse Flow
1, 4, 2, 1, 9, 2 --(1)
Ground/Wiring Fault
1, 4, 2, 1, 9, 3 --(1)
High Process Noise
1, 4, 2, 1, 9, 4 --(1)
Elect Temp Out of Range
1, 4, 2, 1, 9, 5 --(1)
Electrode Coat Limit 2
1, 4, 2, 1, 9, 6 --(1)
Totalizer Limit 1
1, 4, 2, 1, 9, 7 --(1)
Flow Limit 1
1, 4, 2, 1, 9, 8 --(1)
Flow Limit 2
1, 4, 2, 1, 9, 9 --(1)
Cont. Meter Verification
1, 4, 2, 1, 9, 10 --(1)
Pulse Output
1, 4, 2, 2
Pulse Scaling
1, 4, 2, 2, 1
Pulse Width
1, 4, 2, 2, 2
Pulse Mode
1, 4, 2, 2, 3
Pulse Out Loop Test
1, 4, 2, 2, 4
DI/DO Output (Digital I/O)
1, 4, 2, 3
DI/DO 1
1, 4, 2, 3, 1
Configure I/O 1
1, 4, 2, 3, 1, 1
Input
1, 4, 2, 3, 1, 1, 1
Output
1, 4, 2, 3, 1, 1, 2
Not Available/Off
1, 4, 2, 3, 1, 1, 3
DIO 1 Control
1, 4, 2, 3, 1, 2
Digital Input 1
1, 4, 2, 3, 1, 3
Digital Output 1
1, 4, 2, 3, 1, 4
DO 2
1, 4, 2, 3, 2
Flow Limit 1
1, 4, 2, 3, 3
Control 1
1, 4, 2, 3, 3, 1
Mode 1
1, 4, 2, 3, 3, 2
High Limit 1
1, 4, 2, 3, 3, 3
Low Limit 1
1, 4, 2, 3, 3, 4
Flow Limit Hysteresis
1, 4, 2, 3, 3, 5
Flow Limit 2
1, 4, 2, 3, 4
Control 2
1, 4, 2, 3, 4, 1
Mode 2
1, 4, 2, 3, 4, 2
High Limit 2
1, 4, 2, 3, 4, 3
Low Limit 2
1, 4, 2, 3, 4, 4
Flow Limit Hysteresis
1, 4, 2, 3, 4, 5
Total Limit
1, 4, 2, 3, 5
Total Control
1, 4, 2, 3, 5, 1
71
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-1. Traditional Field Communicator Fast Keys (continued)
72
Function
Traditional Fast Keys
Total Mode
1, 4, 2, 3, 5, 2
Total High Limit
1, 4, 2, 3, 5, 3
Total Low Limit
1, 4, 2, 3, 5, 4
Total Limit Hysteresis
1, 4, 2, 3, 5, 5
Diagnostic Status Alert
1, 4, 2, 3, 6
Electronics Failure
1, 4, 2, 3, 6, --(1)
Coil Open Circuit
1, 4, 2, 3, 6, --(1)
Empty Pipe
1, 4, 2, 3, 6, --(1)
Reverse Flow
1, 4, 2, 3, 6, --(1)
Ground/Wiring Fault
1, 4, 2, 3, 6, --(1)
High Process Noise
1, 4, 2, 3, 6, --(1)
Elect Temp Out of Range
1, 4, 2, 3, 6, --(1)
Electrode Coat Limit 1
1, 4, 2, 3, 6, --(1)
Electrode Coat Limit 2
1, 4, 2, 3, 6, --(1)
Cont. Meter Verification
1, 4, 2, 3, 6, --(1)
Reverse Flow
1, 4, 2, 4
Totalizer Setup
1, 4, 2, 5
Totalizer Units
1, 4, 2, 5, 1
Gross Total
1, 4, 2, 5, 2
Net Total
1, 4, 2, 5, 3
Reverse Total
1, 4, 2, 5, 4
Start Totalizer
1, 4, 2, 5, 5
Stop Totalizer
1, 4, 2, 5, 6
Reset Totalizer
1, 4, 2, 5, 7
Alarm Levels
1, 4, 2, 6
Alarm Level
1, 4, 2, 6, 1
Hi Alarm
1, 4, 2, 6, 2
Hi Sat
1, 4, 2, 6, 3
Low Sat
1, 4, 2, 6, 4
Low Alarm
1, 4, 2, 6, 5
HART Output
1, 4, 2, 7
Variable Mapping
1, 4, 2, 7, 1
PV is
1, 4, 2, 7, 1, 1
SV is
1, 4, 2, 7, 1, 2
TV is
1, 4, 2, 7, 1, 3
QV is
1, 4, 2, 7, 1, 4
Poll Address
1, 4, 2, 7, 2
Num Req Preams
1, 4, 2, 7, 3
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-1. Traditional Field Communicator Fast Keys (continued)
Operation
Function
Traditional Fast Keys
Num Resp Preams
1, 4, 2, 7, 4
Burst Mode
1, 4, 2, 7, 5
Burst Option
1, 4, 2, 7, 6
PV
1, 4, 2, 7, 6, --(1)
% Range/Current
1, 4, 2, 7, 6, --(1)
Process Vars/Current
1, 4, 2, 7, 6, --(1)
Dynamic Vars
1, 4, 2, 7, 6, --(1)
LOI Config
1, 4, 3
Language
1, 4, 3, 1
Flowrate Display
1, 4, 3, 2
Totalizer Display
1, 4, 3, 3
Display Lock
1, 4, 3, 4
Meter type
1, 4, 3, 5
LOI Error Mask
1, 4, 3, 6
Signal Processing
1, 4, 4
Operating Mode
1, 4, 4, 1
Man Config DSP
1, 4, 4, 2
Status
1, 4, 4, 2, 1
Samples
1, 4, 4, 2, 2
% Limit
1, 4, 4, 2, 3
Time Limit
1, 4, 4, 2, 4
Coil Drive Freq
1, 4, 4, 3
Low Flow Cutoff
1, 4, 4, 4
PV Damping
1, 4, 4, 5
Universal Trim
1, 4, 5
Device Info
1, 4, 6
Manufacturer
1, 4, 6, 1
Tag
1, 4, 6, 2
Descriptor
1, 4, 6, 3
Message
1, 4, 6, 4
Date
1, 4, 6, 5
Device ID
1, 4, 6, 6
PV Sensor S/N
1, 4, 6, 7
Sensor Tag
1, 4, 6, 8
Write protect
1, 4, 6, 9
Revision No.
1, 4, 6, 10(2)
Universal Rev
1, 4, 6, 10, 1--(2)
Transmitter Rev
1, 4, 6, 10, 2--(2)
73
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-1. Traditional Field Communicator Fast Keys (continued)
Function
Traditional Fast Keys
Software Rev
1, 4, 6, 10, 3--(2)
Final Assembly #
1, 4, 6, 10, 4--(2)
Construction Materials
1, 4, 6, 11(2)
Flange Type
1, 4, 6, 11,1--(2)
Flange Material
1, 4, 6, 11, 2--(2)
Electrode Type
1, 4, 6, 11, 3--(2)
Electrode Material
1, 4, 6, 11, 4--(2)
Liner Material
1, 4, 6, 11, 5--(2)
Device Reset
1, 4, 7
Review
1, 5
(1) These items are in a list format without numeric labels.
(2) To access these features, you must scroll to this option in the HART Field Communicator.
Table 4-2. Device Dashboard Fast Keys
74
Function
Fast Keys
Overview
1
Device Status
Flow Rate
Analog Output Value
Upper Range Value
Lower Range Value
Run Meter Verificaiton
Meter Verification Results
Device Information
Tag
Manufacturer
Model
Final Assembly Number
Device ID
Date
Description
Message
Universal Revision
1,1
1,2
1,3
1,4
1,5
1,6
1,7
1,8
1,8,1,1
1,8,1,2
1,8,1,3
1,8,1,4
1,8,1,5
1,8,1,6
1,8,1,7
1,8,1,8
1,8,2,1
Device Revision
1,8,2,2
Software Revision
Hardware Revision
DD Revision
Sensor Serial Number
Sensor Tag
Calibration Number
Line Size
Lower Sensor Limit
Upper Sensor Limit
Minimum Span
1,8,2,3
1,8,2,4
1,8,2,5
1,8,3,1
1,8,3,2
1,8,3,3
1,8,3,4
1,8,3,5
1,8,3,6
1,8,3,7
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-2. Device Dashboard Fast Keys (continued)
Operation
Function
Fast Keys
Liner Material
Electrode Type
Electrode Material
Flange Type
Flange Material
Write Protect
Alarm Direction
Alarm Type
High Alarm
High Saturation
Low Saturation
Low Alarm
Licenses
Configure
Guided Setup
Initial Setup
Basic Setup
Configure Display
Special Units
Outputs
Analog Output
Pulse Output
Dicrete Input/Output
Totalizer
Reverse Flow
Burst Mode
Variable Mapping
Diagnostics
Configure Basic Diagnostics
Upgrade License
Configure Process Diagnostics
Configure Meter Verification
Re-Baseline Sensor
Alerts
User Alert Conifguration
Analog Alarm Configuration
Optimize Signal Processing
Manual Setup
Flow Units
Lower Range Value
Upper Range Value
Damping
Calibration Number
Line Size
Language
Flow Display
1,8,3,8,1
1,8,3,8,2
1,8,3,8,3
1,8,3,8,4
1,8,3,8,5
1,8,4,1
1,8,4,2
1,8,4,3
1,8,4,4
1,8,4,5
1,8,4,6
1,8,4,7
1,8,5
2
2,1
2,1,1
2,1,1,1
2,1,1,2
2,1,1,3
2,1,2
2,1,2,1
2,1,2,2
2,1,2,3
2,1,2,4
2,1,2,5
2,1,2,7
2,1,2,8
2,1,3
2,1,3,1
2,1,3,2
2,1,3,3
2,1,3,4
2,1,3,5
2,1,4
2,1,4,1
2,1,4,2
2,1,5
2,2
2,2,1,2
2,2,1,3,2
2,2,1,3,3
2,2,1,3,4
2,2,1,4,1
2,2,1,4,2
2,2,1,5,1
2,2,1,5,2
75
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-2. Device Dashboard Fast Keys (continued)
76
Function
Fast Keys
Totalizer Display
Display Lock
Density
Pulse Mode
Pulse Scaling
Pulse Width
Net Total
Gross Total
Reverse Total
Totalizer Control
Totalizer Units
Polling Address
Burst Option
Primary Variable
Secondary Variable
Third Variable
Fourth Variable
Discrete I/O 1 Direction
Dicrete Input 1
Discrete Output 1
Discrete Output 2
Flow Limit 1
High Limit 1
Low Limit 1
Limit 1 Control
Limit 1 Status Alert
Flow Limit 2
High Limit 2
Low Limit 2
Limit 2 Control
Limit 2 Status Alert
Flow Hysteresis
Totalizer Limit
Totalizer High Limit
Totalizer LowLimit
Totalizer Limit Control
Totalizer Limit Status Alert
Totalizer Hysteresis
Diagnostics Status Alert
Enable Diagnostics
License Status
Empty Pipe Value
Empty Pipe Trigger Level
Empty Pipe Counts
Electrode Coating Value
Electrode Coating Level 1 Limit
Electrode Coating Level 2 Limit
2,2,1,5,3
2,2,1,5,4
2,2,2,1,6
2,2,2,2,2
2,2,2,2,3
2,2,2,2,4
2,2,2,3,1
2,2,2,3,2
2,2,2,3,3
2,2,2,3,4
2,2,2,3,5
2,2,3,1,1
2,2,3,1,3
2,2,3,2,1
2,2,3,2,2
2,2,3,2,3
2,2,3,2,4
2,2,4,1,1
2,2,4,1,2
2,2,4,1,3
2,2,4,2
2,2,4,3
2,2,4,3,1
2,2,4,3,2
2,2,4,3,3
2,2,4,3,4
2,2,4,4
2,2,4,4,1
2,2,4,4,2
2,2,4,4,3
2,2,4,4,4
2,2,4,6
2,2,4,5
2,2,4,5,1
2,2,4,5,2
2,2,4,5,3
2,2,4,5,4
2,2,4,7
2,2,4,8
2,2,5,1
2,2,5,2
2,2,5,3,1
2,2,5,3,2
2,2,5,3,3
2,2,5,6,1
2,2,5,6,2
2,2,5,6,3
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-2. Device Dashboard Fast Keys (continued)
Operation
Function
Fast Keys
Electrode Coating Maximum Value
Reset Maximum Electrode Coating Value
Diagnostic Analog Alarm
Recall Last Baseline
No Flow Limit
Flowing Limit
Empty Pipe Limit
Continuous Meter Verification Limit
Enable Continuous Meter Verification Parameters
Coils
Electrodes
Transmitter
Analog Output (Continuous Meter Verification)
Coil Drive Frequency
Auto Zero
Digital Signal Processing (DSP) Operation
DSP Control
Number of Samples
Percent of Rate
Time Limit
Tag
Date
Description
Message
Sensor Serial Number
Sensor Tag
Liner Material
Electrode Type
Electrode Material
Flange Type
Flange Material
Alarm Type
Alert Setup
Flow/Totalizer Limits
Diagnostics
Flow Limit 1
Flow Limit 2
Totalizer Limit
Analog Alarm
Discrete Output Alert
Calibration
Universal Trim
Service tools
Alerts
2,2,5,6,4
2,2,5,6,5
2,2,5,9
2,2,6,1,5
2,2,6,3,1
2,2,6,3,2
2,2,6,3,3
2,2,6,4,1
2,2,6,4,2
2,2,6,4,2,1
2,2,6,4,2,2
2,2,6,4,2,3
2,2,6,4,2,4
2,2,8,3
2,2,8,4
2,2,8,5
2,2,8,6,1
2,2,8,6,2
2,2,8,6,3
2,2,8,6,4
2,2,9,1,1
2,2,9,3,1
2,2,9,3,2
2,2,9,3,3
2,2,9,4,1
2,2,9,4,2
2,2,9,4,3,1
2,2,9,4,3,2
2,2,9,4,3,3
2,2,9,4,3,4
2,2,9,4,3,5
2,2,9,5,2
2,3
2,3,1
2,3,2
2,3,3
2,3,4
2,3,5
2,3,6
2,3,7
2,4
2,4,1
3
3,1
77
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-2. Device Dashboard Fast Keys (continued)
78
Function
Fast Keys
Refresh Alerts
Active Alerts
Variables
Flow Rate
Pulse Output
Analog Output
Net Total
Gross Total
Reverse Total
Empty Pipe Value
Electronics Temperature
Coil Current
Line Noise
Electrode Coating Value
5 Hz Signal-to-Noise Ratio
37 Hz Signal-to-Noise Ratio
Signal Power
Continuous Meter Verification
Baseline Coil Resistance
3,1,1
3,1,2
3,2
3,2,1,1
3,2,1,2
3,2,1,3
3,2,1,4,1
3,2,1,4,2
3,2,1,4,3
3,2,2,1
3,2,2,2
3,2,2,3
3,2,3,1
3,2,3,2
3,2,3,3,1
3,2,3,3,2
3,2,3,3,3
3,2,4
3,2,4,1,1
Baseline Coil Inductance
3,2,4,1,2
Baseline Electrode Resistance
3,2,4,1,3
Continuous Sensor Measurements
3,2,4,2
Continuous Measured Coil Resistance
3,2,4,2,1
Continuous Measured Coil Inductance
3,2,4,2,2
Continuous Coil Baseline Deviation
3,2,4,2,3
Continuous Measured Electrode Resistance
3,2,4,2,4
Continuous Transmitter Measurements
3,2,4,3
Continuous Simulated Velocity
3,2,4,3,1
Continuous Actual Velocity
3,2,4,3,2
Continuous Velocity Deviation
3,2,4,3,3
Continuous Analog Output Measurements
3,2,4,4
Continuous Expected mA Value
3,2,4,4,1
Continuous Actual mA Value
3,2,4,4,2
Continuous mA Deviation
3,2,4,4,3
Trends
3,3
Flow Rate Trend
3,3,1
Empty Pipe Trend
3,3,2
Electronics Temperature Trend
3,3,3
Line Noise Trend
3,3,4
5 Hz Signal-to-Noise Ratio Trend
3,3,5
37 Hz Signal-to-Noise Ratio Trend
3,3,6
Coil Inductance Trend
3,3,7
Coil Resistance Trend
3,3,8
Electrode Resistance Trend
3,3,9
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Table 4-2. Device Dashboard Fast Keys (continued)
Operation
Function
Fast Keys
Maintenance
3,4
Re-Baseline Sensor
3,4,1,1,4
Recall Last Baseline
3,4,1,1,5
No Flow Limit
3,4,1,2,1
Flowing Limit
3,4,1,2,2
Empty Pipe Limit
3,4,1,2,3
Manual Sensor Measurements
3,4,1,3
Manual Measured Coil Resistance
3,4,1,3,1
Manual Measured Coil Inductance
3,4,1,3,2
Manual Measured Electrode Resistance
3,4,1,3,3
Run Manual Meter Verification
3,4,1,4
Manual Meter Verification Results
3,4,1,5
Manual Coil Circuit Test Result
3,4,1,5,1,3
Manual Electrode Circuit Test Result
3,4,1,5,1,6
Manual Sensor Deviation
3,4,1,5,2,3
Manual Sensot Test Result
3,4,1,5,2,4
Manual Simulated Velocity
3,4,1,5,3,1
Manual Actual Velocity
3,4,1,5,3,2
Manual Transmitter Deviation
3,4,1,5,3,3
Manual Transmitter Test Result
3,4,1,5,3,4
Manul Test Conditions
3,4,1,5,4,1
Manual Overall Test Result
3,4,1,5,4,2
Continuous Meter Verification Limit
3,4,2,2
Enable Continuous Meter Verification Parameters
3,4,2,3
Coils
3,4,2,3,1
Electrodes
3,4,2,3,2
Transmitter
3,4,2,3,3
Analog Output (Continuous Meter Verification)
3,4,2,3,4
4-20 mA Verification
3,4,3
Run Manual 4-20 mA Verification
3,4,3,1
4 mA Measurement
3,4,3,2
12 mA Measurement
3,4,3,3
20 mA Measurement
3,4,3,4
Low Alarm Measurement
3,4,3,5
High Alarm Measurement
3,4,3,6
Analog D/A Trim
3,4,4,5
Scaled Analog D/A Trim
3,4,4,6
Electronics (Digital) Trim
3,4,5
Master Reset
3,4,6
Simulate
3,5
Analog Loop Test
3,5,1,1
Pulse Loop Test
3,5,2,1
79
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Figure 4-6. Field Communicator Traditional Menu Tree (Basic Setup and Detailed Setup)
Home
1 Device Setup
2 PV
3 PV AO
4 PV LRV
5 PV URV
Device Setup
1 Process Variables
2 Diagnostics
3 Basic Setup
4 Detailed Setup
5 Review
Basic Setup
1 Tag
2 Flow Units
3 Line Size
4 PV URV
5 PV LRV
6 Calibration Number
7 PV Damping
Flow Units
1 PV Units
2 Special Units
Detailed Setup
1 Additional Params
2 Configure Output
3 LOI Config
4 Signal Processing
5 Universal Trim
6 Device Info
7 Device Reset
Additional Params
1 Coil Drive Freq
2 Density Value
3 PV USL
4 PV LSL
5 PV Min Span
Configure Output
1 Analog Output
2 Pulse Output
3 Digital I/O
4 Reverse Flow
5 Totalizer Setup
6 Alarm Levels
7 HART Output
Special Units
1 Volume Unit
2 Base Volume Unit
3 Conversion Number
4 Base Time Unit
5 Flow Rate Unit
Analog Output
1 PV URV
2 PV LRV
3 PV Loop Current
4 PV Alarm Type
5 AO Loop Test
6 D/A Trim
7 Scaled D/A Trim
8 Alarm Level
9 AO Diagnostic Alarm
Pulse Output
1 Pulse Scaling
2 Pulse Width
3 Pulse Mode
4 Pulse Out Loop Test
Digital I/O
1 DI/DO 1
2 DO 2
3 Flow Limit 1
4 Flow Limit 2
5 Total Limit
6 Diagnostic Status
Alert
AO Diagnostic Alarm
Empty Pipe
Reverse Flow
Ground/Wiring Fault
High Process Noise
Elect Temp Out of Range
Electrode Coat Limit 2
Totalizer Limit 1
Flow Limit 1
Flow Limit 2
Cont. Meter Verification
DI/DO 1
1 Configure I/O 1
2 DIO 1 Control
3 Digital Input 1
4 Digital Output 1
Configure I/O 1
Input
Output
Not Available/Off
Flow Limit 1
1 Control 1
2 Mode 1
3 High Limit 1
4 Low Limit 1
5 Flow Limit Hysteresis
Flow Limit 2
1 Control 2
2 Mode 2
3 High Limit 2
4 Low Limit 2
5 Flow Limit Hysteresis 2
Totalizer Setup
1 Totalizer Units
2 Gross Total
3 Net Total
4 Reverse Total
5 Start Totalizer
6 Stop Totalizer
7 Reset Totalizer
Alarm Levels
1 Alarm Level
2 Hi Alarm
3 Hi Sat
4 Low Sat
5 Low Alarm
LOI Config
1 Language
2 Flowrate Display
3 Totalizer Display
4 Display Lock
5 Meter Type
6 LOI Error Mask
Signal Processing
1 Operating Mode
2 Man Config DSP
3 Coil Drive Freq
4 Low Flow Cutoff
5 PV Damping
Device Info
1 Manufacturer
2 Tag
3 Descriptor
4 Message
5 Date
6 Device ID
7 PV Sensor S/N
8 Sensor Tag
9 Write protect
Revision No.
Construction Materials
80
HART Output
1 Variable Mapping
2 Poll Address
3 Num Req Preams
4 Num Resp Preams
5 Burse Mode
6 Burst Option
Man Config DSP
1 Status
2 Samples
3 % Limit
4 Time Limit
Total Limit
1 Total Control
2 Total Mode
3 Total Hi Limit
4 Total Low Limit
5 Total Limit Hysteresis
Diagnostic Status Alert
Electronics Failure
Coil Open Circuit
Empty Pipe
Reverse Flow
Ground/Wiring Fault
High Process Noise
Elect Temp Out of Range
Electrode Coat Limit 1
Electrode Coat Limit 2
Cont. Meter Verification
Coil Over Current
Sensor Electrode Saturated
Coil Power Limit
Variable Mapping
1 PV is
2 SV is
3 TV is
4 QV is
Burst Option
PV
% Range/Current
Process Vars/Current
Dynamic Vars
Revision No.
1 Universal Rev
2 Transmitter Rev
3 Software Rev
4 Final Assembly #
Construction Materials
1 Flange Type
2 Flange Material
3 Electrode Type
4 Electrode Material
5 Liner Material
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Figure 4-7. Field Communicator Traditional Menu Tree (Process Variables and Diagnostics)
Home
1 Device Setup
2 PV
3 PV AO
4 PV LRV
5 PV URV
Device Setup
1 Process Variables
2 Diagnostics
3 Basic Setup
4 Detailed Setup
5 Review
Basic Setup
1 Tag
2 Flow Units
3 Line Size
4 PV URV
5 PV LRV
6 Calibration Number
7 PV Damping
Flow Units
1 PV Units
2 Special Units
Detailed Setup
1 Additional Params
2 Configure Output
3 LOI Config
4 Signal Processing
5 Universal Trim
6 Device Info
7 Device Reset
Additional Params
1 Coil Drive Freq
2 Density Value
3 PV USL
4 PV LSL
5 PV Min Span
Configure Output
1 Analog Output
2 Pulse Output
3 Digital I/O
4 Reverse Flow
5 Totalizer Setup
6 Alarm Levels
7 HART Output
Special Units
1 Volume Unit
2 Base Volume Unit
3 Conversion Number
4 Base Time Unit
5 Flow Rate Unit
Analog Output
1 PV URV
2 PV LRV
3 PV Loop Current
4 PV Alarm Type
5 AO Loop Test
6 D/A Trim
7 Scaled D/A Trim
8 Alarm Level
9 AO Diagnostic Alarm
Pulse Output
1 Pulse Scaling
2 Pulse Width
3 Pulse Mode
4 Pulse Out Loop Test
Digital I/O
1 DI/DO 1
2 DO 2
3 Flow Limit 1
4 Flow Limit 2
5 Total Limit
6 Diagnostic Status
Alert
AO Diagnostic Alarm
Empty Pipe
Reverse Flow
Ground/Wiring Fault
High Process Noise
Elect Temp Out of Range
Electrode Coat Limit 2
Totalizer Limit 1
Flow Limit 1
Flow Limit 2
Cont. Meter Verification
DI/DO 1
1 Configure I/O 1
2 DIO 1 Control
3 Digital Input 1
4 Digital Output 1
Configure I/O 1
Input
Output
Not Available/Off
Flow Limit 1
1 Control 1
2 Mode 1
3 High Limit 1
4 Low Limit 1
5 Flow Limit Hysteresis
Flow Limit 2
1 Control 2
2 Mode 2
3 High Limit 2
4 Low Limit 2
5 Flow Limit Hysteresis 2
Totalizer Setup
1 Totalizer Units
2 Gross Total
3 Net Total
4 Reverse Total
5 Start Totalizer
6 Stop Totalizer
7 Reset Totalizer
Alarm Levels
1 Alarm Level
2 Hi Alarm
3 Hi Sat
4 Low Sat
5 Low Alarm
LOI Config
1 Language
2 Flowrate Display
3 Totalizer Display
4 Display Lock
5 Meter Type
6 LOI Error Mask
Signal Processing
1 Operating Mode
2 Man Config DSP
3 Coil Drive Freq
4 Low Flow Cutoff
5 PV Damping
Device Info
1 Manufacturer
2 Tag
3 Descriptor
4 Message
5 Date
6 Device ID
7 PV Sensor S/N
8 Sensor Tag
9 Write protect
Revision No.
Construction Materials
Operation
HART Output
1 Variable Mapping
2 Poll Address
3 Num Req Preams
4 Num Resp Preams
5 Burse Mode
6 Burst Option
Man Config DSP
1 Status
2 Samples
3 % Limit
4 Time Limit
Total Limit
1 Total Control
2 Total Mode
3 Total Hi Limit
4 Total Low Limit
5 Total Limit Hysteresis
Diagnostic Status Alert
Electronics Failure
Coil Open Circuit
Empty Pipe
Reverse Flow
Ground/Wiring Fault
High Process Noise
Elect Temp Out of Range
Electrode Coat Limit 1
Electrode Coat Limit 2
Cont. Meter Verification
Coil Over Current
Sensor Electrode Saturated
Coil Power Limit
Variable Mapping
1 PV is
2 SV is
3 TV is
4 QV is
Burst Option
PV
% Range/Current
Process Vars/Current
Dynamic Vars
Revision No.
1 Universal Rev
2 Transmitter Rev
3 Software Rev
4 Final Assembly #
Construction Materials
1 Flange Type
2 Flange Material
3 Electrode Type
4 Electrode Material
5 Liner Material
81
Section 4: Operation
August 2015
Reference Manual
00809-0100-4444, Rev AD
Figure 4-8. Field Communicator Dashboard Menu Tree (Overview and Configuring Guided/Manual Setup)
82
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
Figure 4-9. Field Communicator Dashboard Menu Tree (Configuring Alert Setup and Service Tools)
Operation
83
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
August 2015
4.4
Process variables
LOI menu path
N/A
Traditional Fast Keys
1,1
Device dashboard
1
Process variables are available through the Field Communicator or AMS software suite. These
variables display flow in several ways that reflect your needs and the configuration of your
flowmeter. When commissioning a flowmeter, review each process variable, its function and output,
and take corrective action if necessary before using the flowmeter in a process application.
Primary variable (PV) - The actual measured flow rate of the process fluid. Use the flow units function
to select the units for your application.
Percent of range - The process variable as a percentage of the analog output range, provides an
indication where the current flow of the meter is within the configured range of the flowmeter. For
example, the analog output range may be defined as 0 gal/min to 20 gal/min. If the measured flow is
10 gal/min, the percent of range is 50 percent.
Analog output - The analog output variable provides the analog value for the flow rate. The analog
output refers to the industry standard output in the 4-20 mA range. The analog output and 4-20 mA
loop can be verified using the Analog Feedback diagnostic capability internal to the transmitter (See
“4-20 mA loop verification” on page 119).
Pulse output - The pulse output variable provides the pulse value in terms of a frequency for the flow
rate.
4.4.1
PV - Primary variable
LOI menu path
Home screen if configured to display flow
Traditional Fast Keys
1,1,1
Device dashboard
1,2
The primary variable shows the current measured flow rate. This value determines the analog output
from the transmitter.
4.4.2
PV - Percent of range
LOI menu path
Home screen if configured to display percent span
Traditional Fast Keys
Device dashboard
1,1,2
3,4,4,2
The PV% range shows where in the flow range the current flow value is as a percentage of the
configured span.
84
Operation
Reference Manual
Section 4: Operation
00809-0100-4444, Rev AD
4.4.3
August 2015
PV - Analog output
LOI menu path
N/A
Traditional Fast Keys
1,1,3
Device dashboard
1,3
The PV analog output displays the mA output of the transmitter corresponding to the measured
flow rate.
4.4.4
Pulse output
LOI menu path
N/A
Traditional Fast Keys
1,1,5
Device dashboard
3,2,1,2
The pulse output displays the value of the pulse signal.
Operation
85
Section 4: Operation
August 2015
86
Reference Manual
00809-0100-4444, Rev AD
Operation
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
Section 5
August 2015
Advanced Configuration
Functionality
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 87
Configure outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 87
Configure HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 100
Configure LOI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 104
Additional parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 106
5.1
Introduction
This section contains information for advanced configuration parameters.
The software configuration settings for the Rosemount 8732EM can be accessed through a
HART®-based communicator, Local Operator Interface (LOI), AMS, or through a control system.
Before operating the 8732EM in an actual installation, you should review all of the factory set
configuration data to ensure that they reflect the current application.
5.2
Configure outputs
LOI menu path
Detailed Setup, Output Config
Traditional fast keys
1,4,2
Device dashboard
2,2,2
The configure outputs functionality is used to configure advanced features that control the
analog, pulse, auxiliary, and totalizer outputs of the transmitter.
5.2.1
Analog output
LOI menu path
Detailed Setup, Output Config, Analog
Traditional fast keys
1,4,2,1
Device dashboard
2,2,2,1
The analog output function is used to configure all of the features of the 4-20 mA output.
Upper range value
LOI menu path
Detailed Setup, Output Config, Analog, PV URV
Traditional fast keys
1,4,2,1
Device dashboard
2,2,2,1,4
The upper range value (URV) sets the 20 mA point for the analog output. This value is typically
set to full-scale flow. The units that appear will be the same as those selected under the units
parameter. The URV may be set between –39.3 ft/s to 39.3 ft/s (–12 m/s to 12 m/s) or the
equivalent range based on the selected flow units. There must be at least 1 ft/s (0.3 m/s) span or
equivalent between the URV and LRV.
Advanced Configuration Functionality
87
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Lower range value
LOI menu path
Detailed Setup, Output Config, Analog, PV LRV
Traditional fast keys
1,4,2,1
Device dashboard
2,2,2,1,3
The lower range value (LRV) sets the 4 mA point for the analog output. This value is typically set
to zero flow. The units that appear will be the same as those selected under the units parameter.
The LRV may be set between –39.3 ft/s to 39.3 ft/s (–12 m/s to 12 m/s) or the equivalent range
based on the selected flow units. There must be at least 1 ft/s (0.3 m/s) span or equivalent
between the URV and LRV.
Alarm type
LOI menu path
Detailed Setup, Output Config, Analog, Alarm Type
Traditional fast keys
1,4,2,1,4
Device dashboard
2,2,9,5,1
The analog output alarm type displays the position of the alarm switch on the electronics board.
There are two available positions for this switch:

High

Low
Alarm level
LOI menu path
Detailed Setup, Output Config, Analog, Alarm Level
Traditional fast keys
1,4,2,1,8 or 1,4,2,6
Device dashboard
2,2,9,5,2
The alarm level configuration will drive the transmitter to preset values if an alarm occurs. There
are two options:

Rosemount Alarm and Saturation Values (see table Table 5-1 for specific values)

NAMUR-Compliant Alarm and Saturation Values (see Table 5-2 for specific values)
Table 5-1. Rosemount Values
Level
4-20 mA saturation
4-20 mA alarm
Low
3.9 mA
3.75 mA
High
20.8 mA
22.5 mA
Level
4-20 mA saturation
4-20 mA alarm
Low
3.8 mA
3.5 mA
High
20.5 mA
22.6 mA
Table 5-2. NAMUR Values
88
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
AO diagnostic alarm
LOI menu path
Detailed Setup, Output Config, Analog, AO Diag Alarm
Traditional fast keys
1,4,2,1,9
Device dashboard
2,2,5,9
There are diagnostics that, when under active conditions, do not drive the analog output to
alarm level. The AO diagnostic alarm menu enables selection of these diagnostics to be
associated with an analog alarm. If any of the selected diagnostics are active, it will cause the
analog output to go to the configured alarm level. For a list of diagnostic alarms that can be
configured to drive an analog alarm, see Table 5-3.
Table 5-3. Analog Alarm Diagnostic Options
Diagnostic
LOI Menu Path
Fast Keys
Description
Empty Pipe (1)
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Empty Pipe
1,4,2,1,9,1
Drive to an alarm state when
empty pipe is detected.
Reverse Flow
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Reverse Flow
1,4,2,1,9,2
Drive to an alarm state when
reverse flow is detected.
Grounding / Wiring
Fault(1)
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Ground/Wiring
1,4,2,1,9,3
Drive to an alarm state when
grounding or wiring fault is
detected.
High Process Noise(1)
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Process Noise
1,4,2,1,9,4
Drive to an alarm state when the
transmitter detects high levels of
process noise.
Electronics
Temperature Out of
Range(1)
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Elect Temp
1,4,2,1,9,5
Drive to an alarm state when the
temperature of the electronics
exceeds allowable limits
Electrode Coating
Limit 2(1)
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Elec Coating
1,4,2,1,9,6
Drive to an alarm state when
electrode coating reaches a point
where it impacts the flow
measurement
Totalizer Limit 1
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Total Limit
1,4,2,1,9,7
Drive to an alarm state when the
totalizer value exceeds the
parameters set in the totalizer
limit configuration (see page 5-x
for more details on this
functionality)
Flow Limit 1
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Flow Limit 1
1,4,2,1,9,8
Drive to an alarm state when the
flow rate exceeds the parameters
set in the flow limit 1
configuration (see page 5-x for
more details on this functionality)
Flow Limit 2
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Flow Limit 2
1,4,2,1,9,9
Drive to an alarm state when the
flow rate exceeds the parameters
set in the flow limit 2
configuration (see page 5-x for
more details on this functionality)
Continuous Meter
Verification(1)
Detailed Setup, Output
Config, Analog, AO Diag
Alarm, Cont Meter Ver
(2)
1,4,2,1,9,--
Drive to an alarm state when the
continuous meter verification
diagnostic detects a failure of one
of the tests
(1) See Section 6 for more details on each of the diagnostics
(2) To access these features, you must scroll to this option in the HART Field Communicator.
Advanced Configuration Functionality
89
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
5.2.2
Pulse output
LOI menu path
Detailed Setup, Output Config, Pulse
Traditional fast keys
1,4,2,2
Device dashboard
2,2,2,2
Under this function the pulse output of the 8732EM can be configured.
Pulse scaling
LOI menu path
Detailed Setup, Output Config, Pulse, Pulse Scaling
Traditional fast keys
1,4,2,2,1
Device dashboard
2,2,2,2,3
Transmitter may be commanded to supply a specified frequency between 1 pulse/ day at 39.37
ft/sec (12 m/s) to 10,000Hz at 1 ft/sec (0.3 m/s).
Note
Line size, special units, and density must be selected prior to configuration of the pulse scaling
factor.
The pulse output scaling equates one transistor switch closure pulse to a selectable number of
volume units. The volume unit used for scaling pulse output is taken from the numerator of the
configured flow units. For example, if gal/min had been chosen when selecting the flow unit, the
volume unit displayed would be gallons.
Note
The pulse output scaling is designed to operate between 0 and 10,000Hz. The minimum
conversion factor value is found by dividing the minimum span (in units of volume per second)
by 10,000Hz.
Note
The maximum pulse scaling frequency for transmitters with an intrinsically safe output (output
option code B) is 5000Hz.
When selecting pulse output scaling, the maximum pulse rate is 10,000Hz. With the 110
percent over range capability, the absolute limit is 11,000Hz. For example, if you want the
Rosemount 8732EM to pulse every time 0.01 gallons pass through the sensor, and the flow rate
is 10,000 gal/min, you will exceed the 10,000Hz full-scale limit:
The best choice for this parameter depends upon the required resolution, the number of digits
in the totalizer, the extent of range required, and the maximum frequency limit of the external
counter.
90
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Pulse width
LOI menu path
Detailed Setup, Output Config, Pulse, Pulse Width
Traditional fast keys
1,4,2,2,2
Device dashboard
2,2,2,2,4
The factory default pulse width is 0.5 ms.
The width, or duration, of the pulse can be adjusted to match the requirements of different
counters or controllers (see Figure 5-1). These are typically lower frequency applications (<
1000Hz). The transmitter will accept values from 0.1 ms to 650 ms.
For frequencies higher than 1000Hz, it is recommended to set the pulse mode to 50% duty cycle
by setting the pulse mode to frequency output.
The pulse width will limit the maximum frequency output, If the pulse width is set too wide
(more than 1/2 the period of the pulse) the transmitter will limit the pulse output. See example
below.
Figure 5-1. Pulse Output
Example
If pulse width is set to 100 ms, the maximum output is 5Hz; for a pulse width of 0.5 ms, the
maximum output would be 1000Hz (at the maximum frequency output there is a 50% duty
cycle).
Pulse width
Minimum period (50% duty cycle)
100 ms
200 ms
0.5 ms
1.0 ms
Advanced Configuration Functionality
Maximum frequency
91
Section 5: Advanced Configuration Functionality
Reference Manual
00809-0100-4444, Rev AD
August 2015
To achieve the greatest maximum frequency output, set the pulse width to the lowest value
that is consistent with the requirements of the pulse output power source, pulse driven external
totalizer, or other peripheral equipment.
Example
The maximum flow rate is 10,000 gpm. Set the pulse output scaling such that the transmitter
outputs 10,000Hz at 10,000 gpm.
Note
Changes to pulse width are only required when there is a minimum pulse width required for
external counters, relays, etc.
Example
The external counter is ranged for 350 gpm and pulse is set for one gallon. Assuming the pulse
width is 0.5 ms, the maximum frequency output is 5.833Hz.
92
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Example
The upper range value (20mA) is 3000 gpm. To obtain the highest resolution of the pulse
output, 10,000Hz is scaled to the full scale analog reading.
Pulse mode
LOI menu path
Detailed Setup, Output Config, Pulse, Pulse Mode
Traditional fast keys
1,4,2,2,3
Device dashboard
2,2,2,2,2
The pulse mode configures the frequency output of the pulse. It can be set to either 50% duty
cycle, or fixed. There are two options that pulse mode can be configured to:

Pulse Output (user defines a fixed pulse width)

Frequency Output (pulse width automatically set to 50% duty cycle)
To use pulse width settings, pulse mode must be set to pulse output.
5.2.3
Totalizer
The totalizer provides the total amount of fluid that has passed through the meter. There are
three available totalizers:

Net total - increments with forward flow and decrements with reverse flow (reverse
flow must be enabled). Can be reset to zero using the net total reset function.

Gross/forward total - will only increment with forward flow

Reverse total - will only increment with reverse flow if reverse flow is enabled
Advanced Configuration Functionality
93
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
The maximum value for the totalizers is based on 4,294,967,296 (232) feet or corresponding
unit equivalent. If a totalizer reaches this value, it will automatically reset to zero and then
continue counting.
The gross/forward and reverse totalizers can be reset by manually changing the line size.
Totalizer units
LOI menu path
Detailed Setup, Output Config, Totalizer, Totalizer Units
Traditional fast keys
1,4,2,5,1
Device dashboard
2,2,2,3,5
Totalizer units is used to configure the units in which the totalized value will be displayed. These
units are independent of the flow units. Totalizer units are updated to match the flow units
whenever the flow units are written.
Totalizer display
LOI menu path
Detailed Setup, Output Config, Totalizer Setup, Total Display
Traditional fast keys
1,4,3,3
Device dashboard
2,2,1,5,3
The totalizer screen can be configured to display the net and gross totals or the forward and
reverse totals.
Note: Gross and forward totals are the same value.
Start totalizer
LOI menu path
On totalizer screen, press “E”
Traditional fast keys
1,4,2,5,5
Device dashboard
2,2,2,3,4
Start totalizer starts the totalizer counting from its current value.
Stop totalizer
LOI menu path
On totalizer screen, press “E”
Traditional fast keys
1,4,2,5,6
Device dashboard
2,2,2,3,4
Stop totalizer interrupts the totalizer count until it is restarted again. This feature is often used
during pipe cleaning or other maintenance operations.
Reset totalizer
LOI menu path
On totalizer screen, press right arrow (totalizer must be stopped)
Traditional fast keys
1,4,2,5,7
Device dashboard
2,2,2,3,4
Reset totalizer resets the net totalizer value to zero. The totalizer must be stopped before
resetting.
94
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Note
The totalizer value is stored in the non-volatile memory of the electronics every three seconds. If
power to the transmitter is interrupted, the totalizer value will start at the last saved value when
power is reapplied.
5.2.4
Discrete input/output
This configuration option is only available if the auxiliary output suite (option code AX) was
ordered. The auxiliary output suite provides two channels for control. The discrete input can
provide positive zero return (PZR) and net totalizer reset. The discrete output control function
can be configured to drive an external signal to indicate zero flow, reverse flow, empty pipe,
diagnostic status, flow limit, or transmitter status. A complete list and description of the
available auxiliary functions is provided below.
Discrete input options (Channel 1 only)

PZR (Positive Zero Return). When conditions are met to activate the input, the
transmitter will force the output to zero flow.

Net Total Reset - When conditions are met to activate the input, the transmitter will
reset the net total value to zero.
Discrete output options

Reverse Flow - The output will activate when the transmitter detects a reverse flow
condition.

Zero Flow - The output will activate when a no flow condition is detected.

Transmitter Fault - The output will activate when a transmitter fault condition is
detected.

Empty Pipe - The output will activate when the transmitter detects an empty pipe
condition.

Flow Limit 1 - The output will activate when the transmitter measures a flow rate that
meets the conditions established for the flow limit 1 alert.

Flow Limit 2 - The output will activate when the transmitter measures a flow rate that
meets the conditions established for the flow limit 2 alert.

Diagnostic Status Alert - The output will activate when the transmitter detects a
condition that meets the configured criteria of the diagnostic status alert.

Total Limit - The output will activate when the transmitter net total value meets the
conditions established for the total limit alert.
Channel 1
Channel 1 can be configured as either a discrete input (DI) or as a discrete output (DO).
Advanced Configuration Functionality
95
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
DI/O 1 control
LOI menu path
Detailed Setup, Output Config, DI/DO Config, DI/O 1, DI/O 1 Control
Traditional fast keys
1,4,2,3,1,1
Device dashboard
2,2,4,1,1
This parameter configures the auxiliary output channel 1. It controls whether channel 1 will be a
discrete input or discrete output on terminals 5(-) and 6(+). Note that the transmitter must have
been ordered with the auxiliary output suite (option code AX) to have access to this
functionality.
Discrete input 1
LOI menu path
Detailed Setup, Output Config, DI/DO Config, DI/O 1, DI 1
Traditional fast keys
1,4,2,3,1,1,3
Device dashboard
2,2,4,1,2
This parameter displays the configuration for channel 1 when used as a discrete input. Refer to
the list above for available discrete input functions.
Discrete output 1
LOI menu path
Detailed Setup, Output Config, DI/DO Config, DI/O 1, DO 1
Traditional fast keys
1,4,2,3,1,2,4
Device dashboard
2,2,4,1,3
This parameter displays the configuration for channel 1 when used as a discrete output. Refer to
the list above for available discrete output functions.
Channel 2
Channel 2 is available as discrete output only.
Discrete output 2
LOI menu path
Detailed Setup, Output Config, DI/DO Config, DO 2
Traditional fast keys
1,4,2,3,2
Device dashboard
2,2,4,2
This parameter displays the configuration for channel 2. Refer to the list above for available
discrete output functions.
96
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Flow limit (1 and 2)
LOI menu path
Flow 1: Detailed Setup, Output Config, DI/DO Config, Flow Limit 1
Flow 2: Detailed Setup, Output Config, DI/DO Config, Flow Limit 2
Traditional fast keys
Flow 1: 1,4,2,3,3
Flow 2: 1,4,2,3,4
Device dashboard
Flow 1: 2,2,4,3
Flow 2: 2,2,4,4
There are two configurable flow limits. Configure the parameters that will determine the criteria
for activation of a HART alert if the measured flow rate falls within a set of configured criteria.
This functionality can be used for operating simple batching operations or generating alerts
when certain flow conditions are met. This parameter can be configured as a discrete output if
the transmitter was ordered with the auxiliary output suite (option code AX) and the outputs
are enabled. If a discrete output is configured for flow limit, the discrete output will activate
when the conditions defined under mode configuration are met. See “Mode” on page 97 below.
Control
LOI menu path
Flow 1: Detailed Setup, Output Config, DI/DO Config, Flow Limit 1, Control 1
Flow 2: Detailed Setup, Output Config, DI/DO Config, Flow Limit 2, Control 2
Traditional fast keys
Flow 1: 1,4,2,3,3,1
Flow 2: 1,4,2,3,4,1
Device dashboard
Flow 1: 2,2,4,3,4
Flow 2: 2,2,4,4,4
This parameter turns the flow limit HART alert ON or OFF.
ON - The transmitter will generate a HART alert when the defined conditions are met. If a
discrete output is configured for flow limit, the discrete output will activate when the conditions
for mode are met.
OFF - The transmitter will not generate a HART alert for the flow limit.
Mode
LOI menu path
Flow 1: Detailed Setup, Output Config, DI/DO Config, Flow Limit 1, Mode 1
Flow 2: Detailed Setup, Output Config, DI/DO Config, Flow Limit 2, Mode 2
Traditional fast keys
Flow 1: 1,4,2,3,3,2
Flow 2: 1,4,2,3,4,2
Device dashboard
Flow 1: 2,2,4,3,3
Flow 2: 2,2,4,4,3
The mode parameter sets the conditions under which the flow limit HART alert will activate.
High and low limits exist for each channel and can be configured independently.
> High limit - The HART alert will activate when the measured flow rate exceeds the high limit
set point.
< Low limit - The HART alert will activate when the measured flow rate falls below the low limit
set point.
In range - The HART alert will activate when the measured flow rate is between the high limit
and low limit set points.
Out of range - The HART alert will activate when the measured flow rate exceeds the high limit
set point or falls below the low limit set point.
Advanced Configuration Functionality
97
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
High limit
LOI menu path
Flow 1: Detailed Setup, Output Config, DI/DO Config, Flow Limit 1, High Limit 1
Flow 2: Detailed Setup, Output Config, DI/DO Config, Flow Limit 2, High Limit 2
Traditional fast keys
Flow 1: 1,4,2,3,3,3
Flow 2: 1,4,2,3,4,3
Device dashboard
Flow 1: 2,2,4,3,1
Flow 2: 2,2,4,4,1
Set the flow rate value that corresponds to the high limit set point for the flow limit alert.
Low limit
LOI menu path
Flow 1: Detailed Setup, Output Config, DI/DO Config, Flow Limit 1, Low Limit 1
Flow 2: Detailed Setup, Output Config, DI/DO Config, Flow Limit 2, Low Limit 2
Traditional fast keys
Flow 1: 1,4,2,3,3,4
Flow 2: 1,4,2,3,4,4
Device dashboard
Flow 1: 2,2,4,3,2
Flow 2: 2,2,4,4,2
Set the flow rate value that corresponds to the low limit set point for the flow limit alert.
Flow limit hysteresis
LOI menu path
Flow 1: Detailed Setup, Output Config, DI/DO Config, Flow Limit 1, Hysteresis
Flow 2: Detailed Setup, Output Config, DI/DO Config, Flow Limit 2, Hysteresis
Traditional fast keys
Flow 1: 1,4,2,3,3,5
Device dashboard
2,2,4,6
Flow 2: 1,4,2,3,4,5
Set the hysteresis band for the flow limit to determine how quickly the transmitter comes out of
alert status. The hysteresis value is used for both flow limit 1 and flow limit 2. Changing this
parameter under the configuration parameters for one channel will cause it to also change in the
other channel.
Total limit
LOI menu path
Detailed Setup, Output Config, Totalizer, Total Limit
Traditional fast keys
1,4,2,3,5
Device dashboard
2,2,4,5
Configure the parameters that will determine the criteria for activating a HART alert if the
measured net total falls within a set of configured criteria. This functionality can be used for
operating simple batching operations or generating alerts when certain localized values are
met. This parameter can be configured as a discrete output if the transmitter was ordered with
auxiliary outputs enabled (option code AX). If a digital output is configured for total limit, the
digital output will activate when the conditions for total mode are met.
98
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Total control
LOI menu path
Detailed Setup, Output Config, Totalizer, Total Limit, Total Control
Traditional fast keys
1,4,2,3,5,1
Device dashboard
2,2,4,5,4
This parameter turns the total limit HART alert ON or OFF.
ON - The transmitter will generate a HART alert when the defined conditions are met.
OFF - The transmitter will not generate a HART alert for the total limit.
Total mode
LOI menu path
Detailed Setup, Output Config, Totalizer, Total Limit, Total Mode
Traditional fast keys
1,4,2,3,5,2
Device dashboard
2,2,4,5,3
The total mode parameter sets the conditions under which the total limit HART alert will
activate. High and low limits exist for each channel and can be configured independently.
> High limit - The HART alert will activate when the totalizer value exceeds the high limit set
point.
< Low limit - The HART alert will activate when the totalizer value falls below the low limit set
point.
In range - The HART alert will activate when the totalizer value is between the high limit and low
limit set points.
Out of range - The HART alert will activate when the totalizer value exceeds the high limit set
point or falls below the low limit set point.
Total high limit
LOI menu path
Detailed Setup, Output Config, Totalizer, Total Limit, Tot Hi Limit
Traditional fast keys
1,4,2,3,5,3
Device dashboard
2,2,4,5,1
Set the net total value that corresponds to the high limit set point for the total high limit alert.
Total low limit
LOI menu path
Detailed Setup, Output Config, Totalizer, Total Limit, Tot Low Limit
Traditional fast keys
1,4,2,3,5,4
Device dashboard
2,2,4,5,2
Set the net total value that corresponds to the low limit set point for the total low limit alert.
Advanced Configuration Functionality
99
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Total limit hysteresis
LOI menu path
Detailed Setup, Output Config, Totalizer, Total Limit, Hysteresis
Traditional fast keys
1,4,2,3,5,5
Device dashboard
2,2,4,7
Set the hysteresis band for the total limit to determine how quickly the transmitter comes out of
alert status.
Diagnostic status alert
LOI menu path
Detailed Setup, Output Config, Totalizer, Diagnostic Status Alert
Traditional fast keys
1,4,2,3,6
Device dashboard
2,2,4,8
The diagnostic status alert is used to turn on or off the diagnostics that will cause this alert to
activate.
ON - The diagnostic status alert will activate when a transmitter detects a diagnostic designated
as ON.
OFF - The diagnostic status alert will not activate when diagnostics designated as OFF are
detected.
Alerts for the following diagnostics can be turned ON or OFF:
5.3

Electronics Failure

Coil Open Circuit

Empty Pipe

Reverse Flow

Ground/Wiring Fault

High Process Noise

Electronics Temperature Out of Range

Electrode Coat Limit 1

Electrode Coat Limit 2

Continuous Meter Verification
Configure HART
The 8732EM has four HART variables available as outputs. The variables can be configured for
dynamic readings including flow, total, and diagnostic values. The HART output can also be
configured for burst mode or multi-drop communication if required.
100
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
5.3.1
August 2015
Variable mapping
LOI menu path
Detailed Setup, Output Config, Hart, Variable Map
Traditional fast keys
1,4,2,7,1
Device dashboard
2,2,3,2
Variable mapping allows configuration of the variables that are mapped to the secondary,
tertiary and quaternary variables. The primary variable is fixed to output flow and cannot be
configured.
Primary variable (PV)
LOI menu path
Detailed Setup, Output Config, Hart, Variable Map, PV
Traditional fast keys
1,4,2,7,1,1
Device dashboard
2,2,3,2,1
The primary variable is configured for flow. This variable is fixed and cannot be configured. The
primary variable is tied to the analog output.
Secondary variable (SV)
LOI menu path
Detailed Setup, Output Config, Hart, Variable Map, SV
Traditional fast keys
1,4,2,7,1,2
Device dashboard
2,2,3,2,2
The secondary variable maps the second variable of the transmitter. This variable is a HART only
variable and can be read from the HART signal with a HART enabled input card, or can be burst
for use with a HART Tri-Loop to convert the HART signal to an analog output. Options available
for mapping to this variable can be found in Table 5-4.
Tertiary variable (TV)
LOI menu path
Detailed Setup, Output Config, Hart, Variable Map, TV
Traditional fast keys
1,4,2,7,1,3
Device dashboard
2,2,3,2,3
The tertiary variable maps the third variable of the transmitter. This variable is a HART only
variable and can be read from the HART signal with a HART enabled input card, or can be burst
for use with a HART Tri-Loop to convert the HART signal to an analog output. Options available
for mapping to this variable can be found in Table 5-4.
Advanced Configuration Functionality
101
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Quaternary variable (QV)
LOI menu path
Detailed Setup, Output Config, Hart, Variable Map, QV
Traditional fast keys
1,4,2,7,1,4
Device dashboard
2,2,3,2,4
The quaternary variable maps the fourth variable of the transmitter. This variable is a HART only
variable and can be read from the HART signal with a HART enabled input card, or can be burst
for use with a HART Tri-Loop™ to convert the HART signal to an analog output. Options available
for mapping to this variable can be found in Table 5-4.
Table 5-4. Available Variables
Pulse Output
Empty Pipe Value
Gross Total – TV Default
Transmitter Velocity Deviation
Net Total – SV Default
Electrode Coating Value
Reverse Total – QV Default
Electrode Resistance Value
Electronics Temp
Coil Resistance Value
Line Noise Value
Sensor Calibration Deviation Value
5 Hz Signal to Noise Value
mA Loop Deviation Value
37 Hz Signal to Noise Value
5.3.2
Poll address
LOI menu path
Detailed Setup, Output Config, Hart Output, Poll Address
Traditional fast keys
1,4,2,7,2
Device dashboard
2,2,3,1,1
Poll address enables the poll address to be set for use in a multi-drop configuration. The poll
address is used to identify each meter on the multi-drop line. Follow the on-screen instructions
to set the poll address at a number from 1 to 15. To set or change the flowmeter address,
establish communication with the selected 8732EM in the loop.
Note
The 8732EM poll address is set to zero at the factory, allowing standard operation in a
point-to-point manner with a 4-20 mA output signal. To activate multi-drop communication,
the transmitter poll address must be changed to a number between 1 and 15. This change
deactivates the analog output, sets the output value to 4 mA, and disables the failure mode
alarm signal.
102
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
5.3.3
August 2015
Burst mode
LOI menu path
Detailed Setup, Output Config, HART, Burst Mode
Traditional fast keys
1,4,2,7,5
Device dashboard
2,2,3,1,2
The 8732EM includes a burst mode function that can be enabled to broadcast the primary
variable or all dynamic variables approximately three to four times per second. Burst mode is a
specialized function used in very specific applications. The burst mode function enables you to
select the variables that are broadcast while in the burst mode.
Burst mode enables you to set the burst mode as OFF or ON:

OFF - Turns burst mode off; no data are broadcast over the loop

ON - Turns burst mode on; data selected under burst option are broadcast over the loop
Additional command options may appear that are reserved and do not apply to the 8732EM.
Burst option (burst command)
LOI menu path
Detailed Setup, Output Config, HART, Burst Command
Traditional fast keys
1,4,2,7,6
Device dashboard
2,2,3,1,3
Burst option enables you to select the variable(s) that is broadcast during the transmitter burst.
Choose one of the following options:

1; PV; Primary Variable - Selects the primary variable

2; % range/current; Percent of Range and Loop Current - Selects the variable as
percent of range and analog output

3; Process vars/crnt; All Variables and Loop Current - Selects all variables and analog
output

110; Dynamic vars; Dynamic Variables - Burst all dynamic variables in the transmitter
Request preambles
LOI menu path
Detailed Setup, Output Config, HART, Req Preams
Traditional fast keys
1,4,2,7,3
Device dashboard
N/A
Request preambles is the number of preambles required by the 8732EM for HART communications.
Advanced Configuration Functionality
103
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Response preambles
LOI menu path
Detailed Setup, Output Config, HART, Resp Preams
Traditional fast keys
1,4,2,7,4
Device dashboard
N/A
Response preambles is the number of preambles sent by the 8732EM in response to any host
request.
5.3.4
Configure LOI
LOI menu path
Detailed Setup, LOI Config
Traditional fast keys
1,4,3
Device dashboard
2,2,1,5
The LOI configuration contains functionality to configure the display of the transmitter.
Flow display
LOI menu path
Detailed Setup, LOI Config, Flow Display
Traditional fast keys
1,4,3,2
Device dashboard
2,2,1,5,2
Use flow display to configure the parameters that will appear on the LOI flowrate screen. The
flowrate screen displays two lines of information. Choose one of the following options:

Flowrate and % of Span

% of Span and Net Total

Flowrate and Net Total

% of Span and Gross Total

Flowrate and Gross Total
Totalizer display
LOI menu path
Detailed Setup, LOI Config, Total Display
Traditional fast keys
1,4,3,3
Device dashboard
2,2,1,5,3
Use totalizer display to configure the parameters that will appear on the LOI totalizer screen. The
totalizer screen has two lines of information. Choose one of the following options:
104

Forward Total and Reverse Total

Net Total and Gross Total
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
Language
LOI menu path
Detailed Setup, LOI Config, Language
Traditional fast keys
1,4,3,1
Device dashboard
2,2,1,5,1
Use language to configure the display language shown on the LOI. Choose one of the following
options:

English

Spanish

Portuguese

German

French
LOI error mask
LOI menu path
Detailed Setup, LOI Config, LOI Err Mask
Traditional fast keys
N/A
Device dashboard
N/A
Use LOI error mask to turn off the analog output power error message (AO No Power). This may
be desired if the analog output is not being used.
Display auto lock
LOI menu path
Detailed Setup, LOI Config, Disp Auto Lock
Traditional fast keys
1,4,3,4
Device dashboard
2,2,1,5,4
Use display auto lock to configure the LOI to automatically lock the LOI after a set period of time.
Choose one of the following options:

OFF

1 Minute

10 Minutes (default)
Advanced Configuration Functionality
105
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
5.4
Additional parameters
The following parameters may be required for detailed configuration settings based on your
application.
5.4.1
Coil drive frequency
LOI menu path
Detailed Setup, More Params, Coil Frequency
Traditional fast keys
1,4,3,1
Device dashboard
2,2,8,3
Use coil drive frequency to change the pulse rate of the coils. Choose one of the following
options:

5 Hz - The standard coil drive frequency is 5 Hz, which is sufficient for nearly all
applications.

37 Hz - If the process fluid causes a noisy or unstable output, increase the coil drive
frequency to 37.5 Hz. If the 37 Hz mode is selected, perform the auto zero function for
optimum performance.
See “Auto zero” on page 135.
5.4.2
Process density
LOI menu path
Detailed Setup, More Params, Proc Density
Traditional fast keys
1,4,3,1
Device dashboard
2,2,8,2
Use the process density value to convert from a volumetric flow rate to a mass flow rate using
the following equation:
Qm = Qv x p
Where:
Qm is the mass flow rate
Qv is the volumetric flow rate, and
p is the fluid density
5.4.3
Reverse flow
LOI menu path
Detailed Setup, Output Config, Reverse Flow
Traditional fast keys
1,4,3,1
Device dashboard
2,2,5,1,5
Use reverse flow to enable or disable the transmitter's ability to read flow in the opposite
direction of the flow direction arrow (see Figure 2-4 on page 10). This may occur when the
process has bi-directional flow, or when either the electrode wires or the coil wires are reversed
(see Troubleshooting 9.3.3: Remote wiring). This also enables the totalizer to count in the
reverse direction.
106
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
5.4.4
August 2015
Low flow cutoff
LOI menu path
Detailed Setup, Sig Processing, Low Flow Cutoff
Traditional fast keys
1,4,4,4
Device dashboard
2,2,8,5,2
Low flow cutoff allows the user to set a low flow limit to be specified. The analog output signal is
driven to 4mA for flow rates below the set point. The low flow cutoff units are the same as the PV
units and cannot be changed. The low flow cutoff value applies to both forward and reverse
flows.
5.4.5
PV damping
LOI menu path
Detailed Setup, Sig Processing, PV Damping
Traditional fast keys
1,4,4,5
Device dashboard
2,2,8,1
Primary variable damping allows selection of a response time, in seconds, to a step change in
flow rate. It is most often used to smooth fluctuations in output.
5.4.6
Signal processing
LOI menu path
Detailed Setup, Sig Processing
Traditional fast keys
1,4,3,1
Device dashboard
2,2,8,6
The 8732EM contains several advanced functions that can be used to stabilize erratic outputs
caused by process noise. The signal processing menu contains this functionality.
If the 37 Hz coil drive mode has been set, and the output is still unstable, the damping and signal
processing function should be used. It is important to set the coil drive mode to 37 Hz first, so
the loop response time is not increased.
The 8732EM provides for a very easy and straightforward start-up, and also incorporates the
capability to deal with difficult applications that have previously manifested themselves in a
noisy output signal. In addition to selecting a higher coil drive frequency (37 Hz vs. 5 Hz) to
isolate the flow signal from the process noise, the 8732EM microprocessor can actually
scrutinize each input based on three user-defined parameters to reject the noise specific to the
application.
See Section 7 for the detailed description of how the signal processing works.
Operating mode
LOI menu path
Detailed Setup, Sig Processing, Operating Mode
Traditional fast keys
1,4,3,1
Device dashboard
2,2,8,5,1
The operating mode function can be set to normal mode or filter mode. If set to normal mode,
and the signal is noisy and provides an unstable flow reading, switch to filter mode. Filter mode
automatically uses 37 Hz coil drive frequency and activates signal processing at the factory set
Advanced Configuration Functionality
107
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
default values. When using filter mode, perform an auto zero with no flow and a full sensor.
Either of the parameters (coil drive mode or signal processing) may still be changed individually.
Turning signal processing off or changing the coil drive frequency to 5 Hz will automatically
change the operating mode from filter mode to normal mode.
Signal processing control
LOI menu path
Detailed Setup, Sig Processing, SP Control
Traditional fast keys
1,4,3,1
Device dashboard
2,2,8,6,1
DSP can be turned on or off. When on is selected, the 8732EM output is derived using a running
average of the individual flow inputs. DSP is a software algorithm that examines the quality of
the electrode signal against user-specified tolerances. This average is updated at the rate of 10
samples per second with a coil drive frequency of 5 Hz, and 75 samples per second with a coil
drive frequency of 37Hz. The three parameters that make up signal processing (number of
samples, percent limit, and time limit) are described below.
Number of samples
LOI menu path
Detailed Setup, Sig Processing, SP Control, Samples:
Traditional fast keys
1,4,3,1
Device dashboard
2,2,8,6,2
The number of samples sets the amount of time that inputs are collected and used to calculate
the average value. Each second is divided into tenths with the number of samples equaling the
number of increments used to calculate the average. This parameter can be configured for an
integer value between 0 and 125. The default value is 90 samples.
Percent rate
LOI menu path
Detailed Setup, Sig Processing, SP Control, % Rate:
Traditional fast keys
1,4,3,1
Device dashboard
2,2,8,6,3
This parameter will set the tolerance band on either side of the running average, referring to
percent deviation from the average flow rate. Values within the limit are accepted while values
outside the limit are scrutinized to determine if they are a noise spike or an actual flow change.
This parameter can be configured for an integer value between 0 and 100 percent. The default
value is 2 percent.
Time limit
LOI menu path
Detailed Setup, Sig Processing, SP Control, Time Limit:
Traditional fast keys
1,4,3,1
Device dashboard
2,2,8,6,4
The time limit parameter forces the output and running average values to the new value of an
actual flow rate change that is outside the percent limit boundaries. It thereby limits response
time to flow changes to the time limit value rather than the length of the running average.
108
Advanced Configuration Functionality
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
For example, if the number of samples selected is 100, then the response time of the system is
10 seconds. In some cases this may be unacceptable. By setting the time limit, you can force the
8732EM to clear the value of the running average and re-establish the output and average at the
new flow rate once the time limit has elapsed. This parameter limits the response time added to
the loop. A suggested time limit value of two seconds is a good starting point for most
applicable process fluids. This parameter can be configured between 0 and 256 seconds. The
default value is 2 seconds.
5.5
Configure special units
Special units are used when the application requires units that are not included in the flow units
available from the device. Refer to Table 2-14 for a complete list of the available units.
5.5.1
Base volume unit
LOI menu path
Basic Setup, Flow Units, Special Units, Base Vol Units
Traditional fast keys
1,3,2,2,2
Device dashboard
2,2,1,6
Base volume unit is the unit from which the conversion is being made. Set this variable to the
appropriate option.
5.5.2
Conversion factor
LOI menu path
Basic Setup, Flow Units, Special Units, Conv Factor
Traditional fast keys
1,3,2,2,3
Device dashboard
2,2,1,6
The special units conversion factor is used to convert base units to special units. For a straight
conversion of units from one unit of measure to a different unit of measure, the conversion
factor is the number of base units in the new unit.
For example, if you are converting from gallons to barrels and there are 31 gallons in a barrel,
the conversion factor is 31.
5.5.3
Base time unit
LOI menu path
Basic Setup, Flow Units, Special Units, Base Time Unit
Traditional fast keys
1,3,2,2,4
Device dashboard
2,2,1,6
Base time unit provides the time unit from which to calculate the special units.
For example, if your special units is a volume per minute, select minutes.
Advanced Configuration Functionality
109
Reference Manual
Section 5: Advanced Configuration Functionality
00809-0100-4444, Rev AD
August 2015
5.5.4
Special volume unit
LOI menu path
Basic Setup, Flow Units, Special Units, Volume Unit
Traditional fast keys
1,3,2,2,1
Device dashboard
2,2,1,6
Special volume unit enables you to display the volume unit format to which you have converted
the base volume units. For example, if the special units are abc/min, the special volume variable
is abc. The volume units variable is also used in totalizing the special units flow.
5.5.5
Special flow rate unit
LOI menu path
Basic Setup, Flow Units, Special Units, Rate Unit
Traditional fast keys
1,3,2,2,5
Device dashboard
2,2,1,6
Flow rate unit is a format variable that provides a record of the units to which you are converting.
The Handheld Communicator will display a special units designator as the units format for your
primary variable. The actual special units setting you define will not appear. Four characters are
available to store the new units designation. The 8732EM LOI will display the four character
designation as configured.
Example
To display flow in acre-feet per day, and acre-foot is equal to 43560 cubic feet, the procedure
would be:
110
1.
Set the volume unit to ACFT.
2.
Set the base volume unit to ft3.
3.
Set the conversion factor to 43560.
4.
Set the time base unit to Day.
5.
Set the flow rate unit to AF/D.
Advanced Configuration Functionality
Section 6: Advanced Diagnostics Configuration
Reference Manual
August 2015
00809-0100-4444, Rev AD
Section 6
Advanced Diagnostics
Configuration
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Licensing and enabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tunable empty pipe detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronics temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground/wiring fault detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High process noise detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coated electrode detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-20 mA loop verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMART™ Meter Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Run manual SMART Meter Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous SMART Meter Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMART Meter Verification test results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMART Meter Verification measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optimizing the SMART Meter Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Calibration Verification Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1
page 111
page 112
page 113
page 115
page 115
page 116
page 117
page 119
page 121
page 123
page 125
page 126
page 127
page 130
page 132
Introduction
Rosemount Magnetic Flowmeters provide device diagnostics that detect and warn of abnormal
situations throughout the life of the meter - from Installation to Maintenance and Meter
Verification. With Rosemount Magnetic Flowmeter diagnostics enabled, plant availability and
throughput can be improved, and costs through simplified installation, maintenance and troubleshooting can be reduced.
Table 6-1. Diagnostics Availability
Diagnostic name
Diagnostic category
Product capability
Basic diagnostics
Tunable Empty Pipe
Process
Standard
Electronics Temperature
Maintenance
Standard
Coil Fault
Maintenance
Standard
Transmitter Fault
Maintenance
Standard
Reverse Flow
Process
Standard
Electrode Saturation
Process
Standard
Coil Current
Maintenance
Standard
Coil Power
Maintenance
Standard
High Process Noise
Process
Suite 1 (DA1)
Grounding and Wiring Fault
Installation
Suite 1 (DA1)
Coated Electrode Detection
Process
Suite 1 (DA1)
Commanded Meter Verification
Meter Health
Suite 2 (DA2)
Continuous Meter Verification
Meter Health
Suite 2 (DA2)
4-20 mA Loop Verification
Installation
Suite 2 (DA2)
Advanced diagnostics
Advanced Diagnostics Configuration
111
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
August 2015
Options for accessing Rosemount Magmeter Diagnostics
Rosemount Magmeter Diagnostics can be accessed through the Local Operator Interface (LOI),
a Field Communicator, and AMS® Device Manager.
Access diagnostics through the LOI for quicker installation, maintenance,
and meter verification
Rosemount Magmeter Diagnostics are available through the LOI to make maintenance of every
magmeter easier.
Access diagnostics through AMS Device Manager
The value of the diagnostics increases significantly when AMS is used. The user will see
simplified screen flow and procedures on how to respond to the diagnostics messages.
6.2
Licensing and enabling
All advanced diagnostics are licensed by ordering option code DA1, DA2, or both. In the event
that a diagnostic option is not ordered, advanced diagnostics can be licensed in the field
through the use of a license key. Each transmitter has a unique license key specific to the
diagnostic option code. A trial license is also available to enable the advanced diagnostics. This
temporary functionality will be automatically disabled after 30-days or when power to the
transmitter is cycled, whichever occurs first. This trial code can be used a maximum of three
times per transmitter. See the detailed procedures below for entering the license key and
enabling the advanced diagnostics. To obtain a permanent or trial license key, contact your local
Rosemount representative.
6.2.1
Licensing the 8732EM diagnostics
For licensing the advanced diagnostics, follow the steps below.
1.
Power up the 8732EM transmitter.
2.
Verify the software version is 5.4.4 software or later.
LOI menu path
Detailed Setup, Device Info, Revision Num
Traditional Fast Keys
1,4,6,10, -- (1)
Device dashboard
1,8,2
1. This item is in a list format without numeric labels.
3.
LOI menu path
Detailed Setup, Device Info, Device ID
Traditional Fast Keys
1,4,6,6
Device dashboard
1,8,1,5
4.
112
Determine the Device ID.
Obtain a license key from a local Rosemount representative.
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
5.
Enter license key.
LOI menu path
Diagnostics, Advanced Diagnostics, Licensing, License Key, License Key
Traditional Fast Keys
1,2,3,4,2,2
Device dashboard
1,8,5,4
6.
6.3
August 2015
Enable Advanced Diagnostics.
LOI menu path
Diagnostics, Diag Controls
Traditional Fast Keys
1,2,3
Device dashboard
2,2,5,1
Tunable empty pipe detection
The tunable empty pipe detection provides a means of minimizing issues and false readings
when the pipe is empty. This is most important in batching applications where the pipe may run
empty with some regularity. If the pipe is empty, this diagnostic will activate, set the flow rate to
0, and deliver an alert.
Turning empty pipe on/off
LOI menu path
Diagnostics, Diag Controls, Empty Pipe
Traditional Fast Keys
1,2,1,1
Device dashboard
2,2,5,1,1
The tunable empty pipe detection diagnostic can be turned on or off as required by the
application. The empty pipe diagnostic is shipped turned “On” by default.
6.3.1
Tunable empty pipe parameters
The tunable empty pipe diagnostic has one read-only parameter, and two parameters that can
be custom configured to optimize the diagnostic performance.
Empty pipe (EP) value
LOI menu path
Diagnostics, Variables, Empty Pipe
Traditional Fast Keys
1,2,2,4,1
Device dashboard
2,2,5,3,1
This parameter shows the current empty pipe value. This is a read-only value. This number is a
unit-less number and is calculated based on multiple installation and process variables such as
sensor type, line size, process fluid properties, and wiring. If the empty pipe value exceeds the
empty pipe trigger level for a specified number of updates, then the empty pipe diagnostic alert
will activate.
Advanced Diagnostics Configuration
113
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
August 2015
Empty pipe (EP) trigger level
LOI menu path
Diagnostics, Basic Diagnostics, Empty Pipe, EP Trig Level
Traditional Fast Keys
1,2,2,4,2
Device dashboard
2,2,5,3,2
Limits: 3 to 2000
Empty pipe trigger level is the threshold limit that the empty pipe value must exceed before the
empty pipe diagnostic alert activates. The default setting from the factory is 100.
Empty pipe (EP) counts
LOI menu path
Diagnostics, Basic Diagnostics, Empty Pipe, EP Counts
Traditional Fast Keys
1,2,2,4,3
Device dashboard
2,2,5,3,3
Limits: 2 to 50
Empty pipe counts is the number of consecutive updates that the transmitter must receive
where the empty pipe value exceeds the empty pipe trigger level before the empty pipe
diagnostic alert activates. The default setting from the factory is 5.
6.3.2
Optimizing tunable empty pipe
The tunable empty pipe diagnostic is set at the factory to properly diagnose most applications.
If this diagnostic activates, the following procedure can be followed to optimize the empty pipe
diagnostic for the application.
Example
1.
Record the empty pipe value with a full pipe condition.
Example: Full reading = 0.2
2.
Record the empty pipe value with an empty pipe condition.
Example: Empty reading = 80.0
3.
Set the empty pipe trigger level to a value between the full and empty readings. For
increased sensitivity to empty pipe conditions, set the trigger level to a value closer to
the full pipe value.
Example: Set the trigger level to 25.0
4.
Set the empty pipe counts to a value corresponding to the desired sensitivity level for
the diagnostic. For applications with entrained air or potential air slugs, less sensitivity
may be desired.
Example: Set the counts to 10
114
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
6.4
August 2015
Electronics temperature
The 8732EM continuously monitors the temperature of the internal electronics. If the measured
electronics temperature exceeds the operating limits of –40 to 140 °F (–40 to 60 °C) the
transmitter will go into alarm and generate an alert.
6.4.1
Turning electronics temperature on/off
LOI menu path
Diagnostics, Diag Controls, Elect Temp
Traditional Fast Keys
1,2,1,1, -- (1)
Device dashboard
2,2,5,1,4
1. This item is in a list format without numeric labels.
The electronics temperature diagnostic can be turned on or off as required by the application.The electronics temperature diagnostic will be turned on by default.
6.4.2
Electronics temperature parameters
The electronics temperature diagnostic has one read-only parameter. It does not have any
configurable parameters.
Electronics temperature
LOI menu path
Diagnostics, Variables, Elect Temp
Traditional Fast Keys
1,2,4,2
Device dashboard
2,2,5,7
This parameter shows the current temperature of the electronics. This is a read-only value.
6.5
Ground/wiring fault detection
The transmitter continuously monitors signal amplitudes over a wide range of frequencies. For
the ground/wiring fault detection diagnostic, the transmitter specifically looks at the signal
amplitude at frequencies of 50 Hz and 60 Hz which are the common AC cycle frequencies found
throughout the world. If the amplitude of the signal at either of these frequencies exceeds 5 mV,
that is an indication that there is a ground or wiring issue and that stray electrical signals are
getting into the transmitter. The diagnostic alert will activate indicating that the ground and
wiring of the installation should be carefully reviewed.
The ground/wiring fault detection diagnostic provides a means of verifying installations are
done correctly. If the installation is not wired or grounded properly, this diagnostic will activate
and deliver an alert. This diagnostic can also detect if the grounding is lost over-time due to
corrosion or another root cause.
Advanced Diagnostics Configuration
115
Section 6: Advanced Diagnostics Configuration
6.5.1
Reference Manual
00809-0100-4444, Rev AD
August 2015
Turning ground/wiring fault on/off
LOI menu path
Diagnostics, Diag Controls, Ground/Wiring
Traditional Fast Keys
1,2,1,1, -- (1)
Device dashboard
2,2,5,1,3
1. This item is in a list format without numeric labels.
The ground/wiring fault detection diagnostic can be turned on or off as required by the
application. If the advanced diagnostics suite 1 (DA1 Option) was ordered, then the
ground/wiring fault detection diagnostic will be turned on. If DA1 was not ordered or licensed,
this diagnostic is not available.
6.5.2
Ground/wiring fault parameters
The ground/wiring fault detection diagnostic has one read-only parameter. It does not have any
configurable parameters.
Line noise
LOI menu path
Diagnostics, Variables, Line Noise
Traditional Fast Keys
1,2,4,3
Device dashboard
2,2,5,4,1
The line noise parameter shows the amplitude of the line noise. This is a read-only value. This
number is a measure of the signal strength at 50/60 Hz. If the line noise value exceeds 5 mV,
then the ground/wiring fault diagnostic alert will activate.
6.6
High process noise detection
The high process noise diagnostic detects if there is a process condition causing an unstable or
noisy reading that is not an actual flow variation. A common cause of high process noise is slurry
flow, like pulp stock or mining slurries. Other conditions that cause this diagnostic to activate
are high levels of chemical reaction or entrained gas in the liquid. If unusual noise or flow
variation is seen, this diagnostic will activate and deliver an alert. If this situation exists and is left
without remedy, it will add additional uncertainty and noise to the flow reading.
6.6.1
Turning high process noise on/off
LOI menu path
Diagnostics, Diag Controls, Process Noise
Traditional Fast Keys
1,2,1,1, -- (1)
Device dashboard
2,2,5,1,2
1. This item is in a list format without numeric labels.
The high process noise diagnostic can be turned on or off as required by the application. If the
advanced diagnostics suite 1 (DA1 Option) was ordered, then the high process noise diagnostic
will be turned on. If DA1 was not ordered or licensed, this diagnostic is not available.
116
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
6.6.2
August 2015
High process noise parameters
The high process noise diagnostic has two read-only parameters. It does not have any
configurable parameters. This diagnostic requires that flow be present in the pipe and the
velocity be greater than1 ft/s (0.3 m/s).
5 Hz signal to noise ratio (SNR)
LOI menu path
Diagnostics, Variables, 5Hz SNR
Traditional Fast Keys
1,2,4,4
Device dashboard
2,2,5,5,1
This parameter shows the value of the signal to noise ratio at the coil drive frequency of 5 Hz.
This is a read-only value. This number is a measure of the signal strength at 5 Hz relative to the
amount of process noise. If the transmitter is operating in 5 Hz mode, and the signal to noise
ratio remains below 25 for one minute, then the high process noise diagnostic alert will activate.
37 Hz signal to noise ratio (SNR)
LOI menu path
Diagnostics, Variables, 37Hz SNR
Traditional Fast Keys
1,2,4,5
Device dashboard
2,2,5,5,2
This parameter shows the current value of the signal to noise ratio at the coil drive frequency of
37 Hz. This is a read-only value. This number is a measure of the signal strength at 37 Hz relative
to the amount of process noise. If the transmitter is operating in 37 Hz mode, and the signal to
noise ratio remains below 25 for one minute, then the high process noise diagnostic alert will
activate.
6.7
Coated electrode detection
The coated electrode detection diagnostic provides a means of monitoring insulating coating
buildup on the measurement electrodes. If coating is not detected, buildup over time can lead
to a compromised flow measurement. This diagnostic can detect if the electrode is coated and if
the amount of coating is affecting the flow measurement. There are two levels of electrode
coating.
Limit 1 indicates when coating is starting to occur, but has not compromised the flow
measurement.
Limit 2 indicates when coating is affecting the flow measurement and the meter should be
serviced immediately.
6.7.1
Turning coated electrode detection on/off
LOI menu path
Diagnostics, Diag Controls, Elec Coating
Traditional Fast Keys
1,2,3,1
Device dashboard
2,2,5,1,5
The coated electrode detection diagnostic can be turned on or off as required by the
application. If the advanced diagnostics suite 1 (DA1 option) was ordered, then the coated
Advanced Diagnostics Configuration
117
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
August 2015
electrode detection diagnostic will be turned on. If DA1 was not ordered or licensed, this
diagnostic is not available.
6.7.2
Coated electrode parameters
The coated electrode detection diagnostic has four parameters. Two are read-only and two are
configurable parameters. The electrode coating parameters need to be initially monitored to
accurately set the electrode coating limit levels for each application.
Electrode coating (EC) value
LOI menu path
Diagnostics, Advanced Diag, Elec Coating, EC Current Val
Traditional Fast Keys
1,2,3,1,1
Device dashboard
2,2,5,6,1
The electrode coating value reads the value of the coated electrode detection diagnostic.
Electrode coating (EC) level 1 limit
LOI menu path
Diagnostics, Advanced Diag, Elec Coat, EC Limit 1
Traditional Fast Keys
1,2,3,1,2
Device dashboard
2,2,5,6,2
Set the criteria for the electrode coating limit 1 which indicates when coating is starting to
occur, but has not compromised the flow measurement. The default value for this parameter is
1000 k Ohm.
Electrode coating (EC) level 2 limit
LOI menu path
Diagnostics, Advanced Diag, Elec Coat, EC Limit 2
Traditional Fast Keys
1,2,3,1,3
Device dashboard
2,2,5,6,3
Set the criteria for the electrode coating limit 2 which indicates when coating is affecting the
flow measurement and the meter should be serviced immediately. The default value for this
parameter is 2000 k Ohm.
Maximum electrode coating (EC)
LOI menu path
Diagnostics, Advanced Diag, Elec Coat, EC Max Value
Traditional Fast Keys
1,2,3,1,4
Device dashboard
2,2,5,6,4
The maximum electrode coating value reads the maximum value of the coated electrode
detection diagnostic since the last maximum value reset.
118
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
August 2015
Clear maximum electrode value
LOI menu path
Diagnostics, Advanced Diag, Elec Coat, Reset Max Val
Traditional Fast Keys
1,2,3,1,5
Device dashboard
2,2,5,6,5
Use this method to reset the maximum electrode coating value.
6.8
4-20 mA loop verification
The 4-20 mA loop verification diagnostic provides a means of verifying the analog output loop is
functioning properly. This is a manually initiated diagnostic test. This diagnostic checks the
integrity of the analog loop and provides a health status of the circuit. If the verification does not
pass, this will be highlighted in the results given at the end of the check.
The 4-20 mA loop verification diagnostic is useful for testing the analog output when errors are
suspected. The diagnostic tests the analog loop at five different mA output levels:
6.8.1

4 mA

12 mA

20 mA

Low alarm level

High alarm level
Initiating 4-20 mA loop verification
LOI menu path
Diagnostics, Advanced Diag, 4-20mA Verify, 4-20mA Verify
Traditional Fast Keys
1,2,3,3,1
Device dashboard
3,4,3,1
The 4-20 mA loop verification diagnostic can be initiated as required by the application. If the
advanced diagnostics suite 2 (DA2 Option) was ordered, then the 4-20 mA loop verification
diagnostic will be available. If DA2 was not ordered or licensed, this diagnostic is not available.
6.8.2
4-20 mA loop verification parameters
The 4-20 mA loop verification diagnostic has five read-only parameters plus an overall test
result. It does not have any configurable parameters.
4-20 mA loop verification test result
LOI menu path
Diagnostics, Advanced Diag, 4-20mA Verify, View Results
Traditional Fast Keys
1,2,3,3,2
Device dashboard
3,4,3
Shows the results of the 4-20 mA loop verification test as either passed or failed.
Advanced Diagnostics Configuration
119
Section 6: Advanced Diagnostics Configuration
Reference Manual
00809-0100-4444, Rev AD
August 2015
4 mA measurement
LOI menu path
N/A
Traditional Fast Keys
N/A
Device dashboard
3,4,3,2
Shows the measured value of the 4 mA loop verification test.
12 mA measurement
LOI menu path
N/A
Traditional Fast Keys
N/A
Device dashboard
3,4,3,3
Shows the measured value of the 12 mA loop verification test.
20 mA measurement
LOI menu path
N/A
Traditional Fast Keys
N/A
Device dashboard
3,4,3,4
Shows the measured value of the 20 mA loop verification test.
Low alarm measurement
LOI menu path
N/A
Traditional Fast Keys
N/A
Device dashboard
3,4,3,5
Shows the measured value of the low alarm verification test.
High alarm measurement
LOI menu path
N/A
Traditional Fast Keys
N/A
Device dashboard
3,4,3,6
Shows the measured value of the high alarm verification test.
6.9
SMART™ Meter Verification
The SMART Meter Verification diagnostic provides a means of verifying the flowmeter is within
calibration without removing the sensor from the process. This diagnostic test provides a review
of the transmitter and sensor's critical parameters as a means to document verification of
calibration. The results of this diagnostic provide the deviation amount from expected values
and a pass/fail summary against user-defined criteria for the application and conditions. The
SMART Meter Verification diagnostic can be configured to run continuously in the background
during normal operation, or it can be manually initiated as required by the application.
120
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
6.9.1
August 2015
Sensor baseline (signature) parameters
The SMART Meter Verification diagnostic functions by taking a baseline sensor signature and
then comparing measurements taken during the verification test to these baseline results.
The sensor signature describes the magnetic behavior of the sensor. Based on Faraday's law, the
induced voltage measured on the electrodes is proportional to the magnetic field strength.
Thus, any changes in the magnetic field will result in a calibration shift of the sensor. Having the
transmitter take an initial sensor signature when first installed will provide the baseline for the
verification tests that are done in the future. There are three specific measurements that are
stored in the transmitter's non-volatile memory that are used when performing the calibration
verification.
Coil circuit resistance
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Sensr Baseline, Values, Coil Resist
Traditional Fast Keys
1,2,3,2,3,1,1
Device dashboard
2,2,6,1,1
The coil circuit resistance is a measurement of the coil circuit health. This value is used as a
baseline to determine if the coil circuit is still operating correctly.
Coil inductance (signature)
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Sensr Baseline, Values, Inductnce
Traditional Fast Keys
1,2,3,2,3,1,2
Device dashboard
2,2,6,1,2
The coil inductance is a measurement of the magnetic field strength. This value is used as a
baseline to determine if a sensor calibration shift has occurred.
Electrode circuit resistance
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Sensr Baseline, Values, Electrode
Res
Traditional Fast Keys
1,2,3,2,3,1,3
Device dashboard
2,2,6,1,3
The electrode circuit resistance is a measurement of the electrode circuit health. This value is
used as a baseline to determine if the electrode circuit is still operating correctly.
6.9.2
Establishing the sensor baseline (signature)
The first step in running the SMART Meter Verification test is establishing the reference
signature that the test will use as the baseline for comparison. This is accomplished by having
the transmitter take a signature of the sensor.
Advanced Diagnostics Configuration
121
Section 6: Advanced Diagnostics Configuration
Reference Manual
00809-0100-4444, Rev AD
August 2015
Reset baseline (re-signature meter)
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Sensr Baseline, Reset Baseline
Traditional Fast Keys
1,2,3,2,3,2
Device dashboard
2,2,6,1,4
Having the transmitter take an initial sensor signature when first installed will provide the
baseline for the verification tests that are done in the future. The sensor signature should be
taken during the start-up process when the transmitter is first connected to the sensor, with a
full line, and ideally with no flow in the line. Running the sensor signature procedure when there
is flow in the line is permissible, but this may introduce some noise into the electrode circuit
resistance measurement. If an empty pipe condition exists, then the sensor signature should
only be run for the coils.
Once the sensor signature process is complete, the measurements taken during this procedure
are stored in non-volatile memory to prevent loss in the event of a power interruption to the
meter. This initial sensor signature is required for both manual and continuous SMART Meter
Verification.
Recall values (recall last saved)
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Sensr Baseline, Recall Values
Traditional Fast Keys
1,2,3,2,3,3
Device dashboard
2,2,6,1,5
In the event that the sensor baseline was reset accidentally or incorrectly, this function will
restore the previously saved sensor baseline values.
6.9.3
SMART Meter Verification test criteria
The Smart Meter Verification diagnostic provides the ability to customize the test criteria to
which the verification must be tested. The test criteria can be set for each of the flow conditions
discussed above.
No flow limit
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Test Criteria, No Flow
Traditional Fast Keys
1,2,3,2,4,1
Device dashboard
2,2,6,3,1
Set the test criteria for the no flow condition. The factory default for this value is set to five
percent with limits configurable between one and ten percent. This parameter applies to
manually initiated test only.
122
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
August 2015
Flowing full limit
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Test Criteria, Flowing Full
Traditional Fast Keys
1,2,3,2,4,2
Device dashboard
2,2,6,3,2
Set the test criteria for the flowing, full condition. The factory default for this value is set to five
percent with limits configurable between one and ten percent. This parameter applies to
manually initiated tests only.
Empty pipe limit
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Test Criteria, Empty Pipe
Traditional Fast Keys
1,2,3,2,4,3
Device dashboard
2,2,6,3,3
Set the test criteria for the empty pipe condition. The factory default for this value is set to five
percent with limits configurable between one and ten percent. This parameter applies to
manually initiated test only.
Continuous limit
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Test Criteria, Continual
Traditional Fast Keys
1,2,3,2,4,4
Device dashboard
2,2,6,4,1
Set the test criteria for the continuous SMART Meter Verification diagnostic. The factory default
for this value is set to five percent with limits configurable between two and ten percent. If the
tolerance band is set too tightly, under empty pipe conditions or noisy flowing conditions, a
false failure of the transmitter test may occur.
6.10
Run manual SMART Meter Verification
LOI menu path
Diagnostics, Advanced Diag, Meter Verify, Run Meter Ver
Traditional Fast Keys
1,2,3,2,1
Device dashboard
1,6
The SMART Meter Verification diagnostic will be available if the advanced diagnostic suite (DA2)
was ordered. If DA2 was not ordered or licensed, this diagnostic will not be available. This
method will initiate the manual meter verification test.
Advanced Diagnostics Configuration
123
Section 6: Advanced Diagnostics Configuration
6.10.1
Reference Manual
00809-0100-4444, Rev AD
August 2015
Test conditions
SMART Meter Verification can be initiated under three possible test conditions. This parameter
is set at the time that the sensor baseline or SMART Meter Verification test is manually initiated.
No flow
Run the SMART Meter Verification test with a full pipe and no flow in the line. Running the
SMART Meter Verification test under this condition provides the most accurate results and the
best indication of magnetic flowmeter health.
Flowing full
Run the SMART Meter Verification test with a full pipe and flow in the line. Running the SMART
Meter Verification test under this condition provides the ability to verify the magnetic
flowmeter health without shutting down the process flow in applications when a shutdown is
not possible. Running the diagnostic under flowing conditions can cause a false test failure if
there is significant process noise present.
Empty pipe
Run the SMART Meter Verification test with an empty pipe. Running the SMART Meter
Verification test under this condition provides the ability to verify the magnetic flowmeter
health with an empty pipe. Running the verification diagnostic under empty pipe conditions will
not check the electrode circuit health.
6.10.2
Test scope
The manually initiated SMART Meter Verification test can be used to verify the entire flowmeter
installation or individual parts such as the transmitter or sensor. This parameter is set at the time
that the SMART Meter Verification test is manually initiated. There are three test scopes from
which to choose.
All
Run the SMART Meter Verification test and verify the entire flowmeter installation. This
parameter results in the diagnostic performing the transmitter calibration verification, sensor
calibration verification, coil health check, and electrode health check. Transmitter calibration
and sensor calibration are verified to the percentage associated with the test condition selected
when the test was initiated. This setting applies to manually initiated tests only.
Transmitter
Run the SMART Meter Verification test on the transmitter only. This results in the verification
test only checking the transmitter calibration to the limits of the test criteria selected when the
verification test was initiated. This setting applies to manually initiated tests only.
Sensor
Run the SMART Meter Verification test on the sensor only. This results in the verification test
checking the sensor calibration to the limits of the test criteria selected when the SMART Meter
Verification test was initiated, verifying the coil circuit health, and the electrode circuit health.
This setting applies to manually initiated tests only.
124
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
6.11
August 2015
Continuous SMART Meter Verification
LOI menu path
Diagnostics, Diag Controls, Cont Meter Ver
Traditional Fast Keys
1,2,1,3
Device dashboard
2,2,6,4
Continuous SMART Meter Verification can be used to monitor and verify the health of the
flowmeter system. The continuous SMART Meter Verification will not report results until 30
minutes after powering up to ensure the system is stable and to avoid false failures.
6.11.1
Test scope
Continuous SMART Meter Verification can be configured to monitor the sensor coils, electrodes,
transmitter calibration, and analog output. All of these parameters can be individually enabled
or disabled. These parameters apply to continuous SMART Meter Verification only.
Coils
LOI menu path
Diagnostics, Diag Controls, Cont Meter Ver, Coils
Traditional Fast Keys
1,2,1,3,1
Device dashboard
2,2,6,4,2,1
Continuously monitor the sensor coil circuit by enabling this continuous SMART Meter
Verification parameter.
Electrodes
LOI menu path
Diagnostics, Diag Controls, Cont Meter Ver, Electrodes
Traditional Fast Keys
1,2,1,3,2
Device dashboard
2,2,6,4,2,2
Continuously monitor the electrode resistance by enabling this continuous SMART Meter
Verification parameter.
Transmitter
LOI menu path
Diagnostics, Diag Controls, Cont Meter Ver, Transmitter
Traditional Fast Keys
1,2,1,3,3
Device dashboard
2,2,6,4,2,3
Continuously monitor the transmitter calibration by enabling this continuous SMART Meter
Verification parameter.
Analog output
LOI menu path
Diagnostics, Diag Controls, Cont Meter Ver, Analog Output
Traditional Fast Keys
1,2,1,3,4
Device dashboard
2,2,6,4,2,4
Continuously monitor the analog output signal by enabling this continuous SMART Meter
Verification parameter.
Advanced Diagnostics Configuration
125
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
August 2015
6.12
SMART Meter Verification test results
If the SMART Meter Verification test is manually initiated, the transmitter will make several
measurements to verify the transmitter calibration, sensor calibration, coil circuit health, and
electrode circuits health. The results of these tests can be reviewed and recorded on the Manual
Calibration Verification Results form found on page 132. Print the "Manual Calibration
Verification Results" form and enter the test results as you view them. The completed form can
be used to validate that the meter is within the required calibration limits to comply with
governmental regulatory agencies.
Depending on the method used to view the results, they will be displayed in either a menu
structure, as a method, or in the report format. When using the HART® Field Communicator,
each individual parameter can be viewed as a menu item. When using the LOI, the parameters
are viewed as a method using the left arrow key to cycle through the results. In AMS, the
calibration verification report is populated with the necessary data eliminating the need to
manually complete the form found on page 132.
When using AMS there are two possible methods that can be used to print the report:

Method one involves using the print functionality within the EDDL screen. This print
functionality essentially prints a screen shot of the report.

Method two involves using the print feature within AMS while on the Maintenance
Service Tools screen. This will result in a printout of all of the maintenance information.
Page one of the report contains the meter verification result data.
The results are displayed in the order found in the table below. Each parameter displays a value
used by the diagnostic to evaluate meter health.
Table 6-2. Manual Smart Meter Verification Test Parameters
Parameter
(Diagnostics, Variables, MV Results, Manual Results)
Traditional
Fast keys
Device Dashboard
Fast keys
1
Test Condition
Test Condition
1,2,3,2,2,1,1
3,4,1,5,4,1
2
Test Criteria
Test Criteria
1,2,3,2,2,1,2
3,4,1,3
3
8714i Test Result
MV Results
1,2,3,2,2,1,3
3,4,1,5,4,2
4
Simulated Velocity
Sim Velocity
1,2,3,2,2,1,4
3,4,1,5,3,1
5
Actual Velocity
ActualVelocity
1,2,3,2,2,1,5
3,4,1,5,3,2
6
Velocity Deviation
Flow Sim Dev
1,2,3,2,2,1,6
3,4,1,5,3,3
7
Xmtr Cal Test Result
Xmtr Cal Verify
1,2,3,2,2,1,7
3,4,1,5,3,4
8
Sensor Cal Deviation
Sensor Cal Dev
1,2,3,2,2,1,8
3,4,1,5,2,3
9
Sensor Cal Test Result
Sensor Cal
1,2,3,2,2,1,9
3,4,1,5,2,4
10
11
Coil Circuit Test Result
Electrode Circuit Test
Result
LOI menu path
Coil Circuit
Electrode Ckt
1,2,3,2,2,1,--
(1)
3,4,1,5,1,3
(1)
3,4,1,5,1,6
1,2,3,2,2,1,--
1. To get to this value, use the down arrow to scroll through the menu list.
126
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
August 2015
Table 6-3. Continuous SMART Meter Verification Test Parameters
(Diagnostics, Variables, MV Results, Continual Res,...)
Traditional
Fast keys
Device Dashboard
Fast keys
Continuous Limit
Test Criteria
1,2,3,2,2,2,1
3,4,2,2
2
Simulated Velocity
Sim Velocity
1,2,3,2,2,2,2
3,2,4,3,1
3
Actual Velocity
ActualVelocity
1,2,3,2,2,2,3
3,2,4,3,2
4
Velocity Deviation
Flow Sim Dev
1,2,3,2,2,2,4
3,2,4,3,3
5
Coil Signature
Coil Inductnce
1,2,3,2,2,2,5
3,2,4,2,2
6
Sensor Cal Deviation
Sensor Cal Dev
1,2,3,2,2,2,6
3,2,4,2,3
7
Coil Resistance
Coil Resist
1,2,3,2,2,2,7
3,2,4,2,1
8
Electrode Resistance
Electrode Res
1,2,3,2,2,2,8
3,2,4,2,4
9
mA Expected
4-20 mA Expect
1,2,3,2,2,2,9
3,2,4,4,1
LOI menu path
Parameter
1
10
11
mA Actual
mA Deviation
4-20 mA Actual
AO FB Dev
(1)
3,2,4,4,2
(1)
3,2,4,4,3
1,2,3,2,2,2,-1,2,3,2,2,2,--
1. To get to this value, use the down arrow to scroll through the menu list.
6.13
SMART Meter Verification measurements
The SMART Meter Verification test will make measurements of the coil resistance, coil signature,
and electrode resistance and compare these values to the values taken during the sensor
signature process to determine the sensor calibration deviation, the coil circuit health, and the
electrode circuit health. In addition, the measurements taken by this test can provide additional
information when troubleshooting the meter.
Coil circuit resistance
LOI menu path
Traditional Fast Keys
Manual: Diagnostics, Advanced Diag, Meter Verify, Measurements, Manual
Measure, Coil Resist
Continuous: Diagnostics, Advanced Diag, Meter Verify, Measurements,
Continual Meas, Coil Resist
Manual: 1,2,3,2,5,1,1
Continuous: 1,2,3,2,5,2,1
Device dashboard
Manual: 3,4,1,3,1
Continuous: 3,2,4,2,1
The coil circuit resistance is a measurement of the coil circuit health. This value is compared to
the coil circuit resistance baseline measurement taken during the sensor signature process to
determine coil circuit health. This value can be continuously monitored using continuous
SMART Meter Verification.
Advanced Diagnostics Configuration
127
Section 6: Advanced Diagnostics Configuration
Reference Manual
00809-0100-4444, Rev AD
August 2015
Coil signature
LOI menu path
Traditional Fast Keys
Manual: Diagnostics, Advanced Diag, Meter Verify, Measurements, Manual
Measure, Coil Inductnce
Continuous: Diagnostics, Advanced Diag, Meter Verify, Measurements,
Continual Meas, Coil Inductnce
Manual: 1,2,3,2,5,1,2
Continuous: 1,2,3,2,5,2,2
Device dashboard
Manual: 3,4,1,3,2
Continuous: 3,2,4,2,2
The coil signature is a measurement of the magnetic field strength. This value is compared to
the coil signature baseline measurement taken during the sensor signature process to
determine sensor calibration deviation. This value can be continuously monitored using
continuous SMART Meter Verification.
Electrode circuit resistance
LOI menu path
Traditional Fast Keys
Manual: Diagnostics, Advanced Diag, Meter Verify, Measurements, Manual
Measure, Electrode Res
Continuous: Diagnostics, Advanced Diag, Meter Verify, Measurements,
Continual Meas, Electrode Res
Manual: 1,2,3,2,5,1,3
Continuous: 1,2,3,2,5,2,3
Device dashboard
Manual: 3,4,1,3,3
Continuous: 3,2,4,2,4
The electrode circuit resistance is a measurement of the electrode circuit health. This value is
compared to the electrode circuit resistance baseline measurement taken during the sensor
signature process to determine electrode circuit health. This value can be continuously
monitored using continuous SMART Meter Verification.
Actual velocity
LOI menu path
Traditional Fast Keys
Manual: Diagnostics, Advanced Diag, Meter Verify, Measurements, Manual
Measure, Actual Velocity
Continuous: Diagnostics, Advanced Diag, Meter Verify, Measurements,
Continual Meas, Actual Velocity
Manual: 1,2,3,2,2,1,5
Continuous: 1,2,3,2,5,2,4
Device dashboard
Manual: 3,4,1,5,3,2
Continuous: 3,2,4,3,2
The actual velocity is a measurement of the simulated velocity signal. This value is compared to
the simulated velocity to determine transmitter calibration deviation. This value can be
continuously monitored using continuous SMART Meter Verification.
128
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
August 2015
Flow simulation deviation
Manual: Diagnostics, Variables, MV Results, Manual Results, Flow Sim Dev
LOI menu path
Continuous: Diagnostics, Advanced Diag, Meter Verify, Measurements,
Continual Meas, Flow Sim Dev
Traditional Fast Keys
Manual: 1,2,3,2,2,1,6
Continuous: 1, 2, 3, 2, 2, 2, 4
Device dashboard
Manual: 3,4,1,5,3,3
Continuous: 3,2,4,3,3
The flow simulation deviation is a measurement of the percent difference between the
simulated velocity and the actual measured velocity from the transmitter calibration
verification test. This value can be continuously monitored using continuous SMART Meter
Verification.
4-20 mA expected value
Manual: Diagnostics, Advanced Diag, 4-20 mA Verify, View Results
LOI menu path
Continuous: Diagnostics, Advanced Diag, Meter Verify, Measurements,
Continual Meas, 4-20 mA Expect
Traditional Fast Keys
Manual: 1,2,3,3,2
Continuous: 1,2,3,2,5,2,5
Device dashboard
Manual: N/A
Continuous: 3,2,4,4,1
The 4-20 mA expected value is the simulated analog signal used for the 4-20 mA meter
verification test. This value is compared to the actual analog signal to determine analog output
deviation. This value can be continuously monitored using continuous SMART Meter
Verification.
4-20 mA actual value
Manual: Diagnostics, Advanced Diag, 4-20 mA Verify, View Results
LOI menu path
Continuous: Diagnostics, Advanced Diag, Meter Verify, Measurements,
Continual Meas, 4-20 mA Actual
Traditional Fast Keys
Manual: 1,2,3,3,2
Continuous: 1,2,3,2,5,2,6
Device dashboard
Manual: N/A
Continuous: 3,2,4,4,1
The 4-20 mA actual value is the measured analog signal used for the 4-20 mA meter verification
test. This value is compared to the simulated analog signal to determine analog output
deviation. This value can be continuously monitored using continuous SMART Meter
Verification.
Advanced Diagnostics Configuration
129
Section 6: Advanced Diagnostics Configuration
Reference Manual
00809-0100-4444, Rev AD
August 2015
4-20 mA deviation
Manual: Diagnostics, Advanced Diag, 4-20 mA Verify, View Results
LOI menu path
Continuous: Diagnostics, Advanced Diag, Meter Verify, Measurements,
Continual Meas, AO FB Dev
Traditional Fast Keys
Manual: 1,2,3,3,2
Continuous: 1,2,3,2,2,2, --(1)
Device dashboard
Manual: N/A
Continuous: 3,2,4,4,1
1. To get to this value, the down arrow must be used to scroll through the menu list
The 4-20 mA deviation is a measurement of the percent difference between the simulated
analog signal and the actual measured analog signal from the analog output verification test.
This value can be continuously monitored using continuous SMART Meter Verification.
6.14
Optimizing the SMART Meter Verification
The SMART Meter Verification diagnostic can be optimized by setting the test criteria to the
desired levels necessary to meet the compliance requirements of the application. The following
examples below will provide some guidance on how to set these levels.
Example
An effluent meter must be certified annually to comply with environmental regulations. This
example regulation requires that the meter be certified to five percent.
Since this is an effluent meter, shutting down the process may not be viable. In this instance the
SMART Meter Verification test will be performed under flowing conditions. Set the test criteria
for flowing, full to five percent to meet the requirements of the governmental agencies.
Example
A pharmaceutical company requires bi-annual verification of meter calibration on a critical feed
line for one of their products. This is an internal standard, and the plant requires a calibration
record be kept on-hand. Meter calibration on this process must meet two percent. The process
is a batch process so it is possible to perform the calibration verification with the line full and
with no flow.
Since the SMART Meter Verification test can be run under no flow conditions, set the test criteria
for no flow to two percent to comply with the necessary plant standards.
Example
A food and beverage company requires an annual calibration of a meter on a product line. The
plant standard calls for the accuracy to be three percent or better. They manufacture this
product in batches, and the measurement cannot be interrupted when a batch is in process.
When the batch is complete, the line goes empty.
Since there is no means of performing the SMART Meter Verification test while there is product
in the line, the test must be performed under empty pipe conditions. The test criteria for empty
pipe should be set to three percent, and it should be noted that the electrode circuit health
cannot be verified.
130
Advanced Diagnostics Configuration
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
6.14.1
August 2015
Optimizing continuous SMART Meter Verification
Example
For continuous SMART Meter Verification, there is only one test criteria value to configure, and it
will be used for all flow conditions. The factory default is set to five percent to minimize the
potential for false failures under empty pipe conditions. For best results, set the criteria to match
the maximum value of the three test criteria set during manual meter verification (no flow,
flowing full, and empty pipe).
For example, a plant might set the following manual meter verification test criteria: two percent
for no flow, three percent for flowing full, and four percent for empty pipe. In this case, the
maximum test criterion is four percent, so the test criteria for continuous SMART Meter
Verification should be set to four percent. If the tolerance band is set too tightly, under empty
pipe conditions or noisy flowing conditions, a false failure of the transmitter test may occur.
Advanced Diagnostics Configuration
131
Reference Manual
Section 6: Advanced Diagnostics Configuration
00809-0100-4444, Rev AD
August 2015
Manual Calibration Verification Results
Report parameters
User Name: _____________________________________________
Calibration Conditions:
Tag #:__________________________________________________
Test Conditions:
q Internal q External
q Flowing q No Flow, Full Pipe q Empty Pipe
Flowmeter information and configuration
Software Tag:
PV URV (20 mA scale):____________________________________
Calibration Number:
PV LRV (4 mA scale):_____________________________________
Line Size:
PV Damping:____________________________________________
Transmitter calibration verification results
Sensor calibration verification results
Simulated Velocity:
Sensor Deviation %:_____________________________________
Actual Velocity:
Sensor Test:
Deviation %:
Coil Circuit Test:
q PASS /
q FAIL / q NOT TESTED
Transmitter:
Electrode Circuit Test:
q PASS /
q FAIL / q NOT TESTED
q PASS / q FAIL / q NOT TESTED
q PASS / q FAIL / q NOT TESTED
Summary of Calibration Verification results
Verification Results: The result of the flowmeter verification test is:
q PASSED / q FAILED
Verification Criteria: This meter was verified to be functioning within _____________ % of deviation from the original test parameters.
Signature:____________________________________________
132
Date:__________________________________________________
Advanced Diagnostics Configuration
Section 7: Digital Signal Processing
Reference Manual
August 2015
00809-0100-4444, Rev AD
Section 7
Digital Signal Processing
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Process noise profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High process noise diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optimizing flow reading in noisy applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Explanation of signal processing algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1
page 133
page 133
page 134
page 134
page 134
page 138
Introduction
Magmeters are used in applications that can create noisy flow readings. The Rosemount
8732EM has the capability to deal with difficult applications that have previously manifested
themselves in a noisy output signal. In addition to selecting a higher coil drive frequency (37 Hz
vs. 5 Hz) to isolate the flow signal from the process noise, the 8732EM microprocessor has
digital signal processing that is capable of rejecting the noise specific to the application. This
section explains the different types of process noise, provides instructions for optimizing the
flow reading in noisy applications, and provides a detailed description of the digital signal
processing functionality.
7.2
Safety messages
Instructions and procedures in this section may require special precautions to ensure the safety
of the personnel performing the operations. Read the following safety messages before
performing any operation described in this section.
Explosions could result in death or serious injury.
Verify the operating atmosphere of the sensor and transmitter is consistent with the
appropriate hazardous locations certifications.

Do not remove the transmitter cover in explosive atmospheres when the circuit is live.

Before connecting a HART-based communicator in an explosive atmosphere, make
sure the instruments in the loop are installed in accordance with intrinsically safe or
non-incendive field wiring practices.

Both transmitter covers must be fully engaged to meet explosion-proof requirements.
Failure to follow safe installation and servicing guidelines could result in death or
serious injury.

Installation should be performed by qualified personnel only.

Do not perform any service other than those contained in this manual.

Process leaks may result in death or serious injury.

The electrode compartment may contain line pressure; it must be depressurized
before the cover is removed.
High voltage that may be present on leads could cause electrical shock.


Digital Signal Processing
Avoid contact with leads and terminals.
133
Reference Manual
Section 7: Digital Signal Processing
00809-0100-4444, Rev AD
August 2015
7.3
Process noise profiles
1/f noise
This type of noise has higher amplitudes at lower frequencies, but generally degrades over
increasing frequencies. Potential sources of 1/f noise include chemical mixing and slurry flow
particles rubbing against the electrodes.
Spike noise
This type of noise generally results in a high amplitude signal at specific frequencies which can
vary depending on the source of the noise. Common sources of spike noise include chemical
injections directly upstream of the flowmeter, hydraulic pumps, and slurry flows with low
concentrations of particles in the stream. The particles bounce off of the electrode generating a
“spike” in the electrode signal. An example of this type of flow stream would be a recycle flow in
a paper mill.
White noise
This type of noise results in a high amplitude signal that is relatively constant over the frequency
range. Common sources of white noise include chemical reactions or mixing that occurs as the
fluid passes through the flowmeter and high concentration slurry flows where the particulates
are constantly passing over the electrode head. An example of this type of flow stream would be
a basis weight stream in a paper mill.
7.4
High process noise diagnostic
The transmitter continuously monitors signal amplitudes over a wide range of frequencies. For
the high process noise diagnostic, the transmitter specifically looks at the signal amplitude at
frequencies of 2.5 Hz, 7.5 Hz, 32.5 Hz, and 42.5 Hz. The transmitter uses the values from 2.5
and 7.5 Hz and calculates an average noise level. This average is compared to the amplitude of
the signal at 5 Hz. If the signal amplitude is not 25 times greater than the noise level, and the coil
drive frequency is set at 5 Hz, the high process noise diagnostic will trip indicating that the flow
signal may be compromised. The transmitter performs the same analysis around the 37.5 Hz
coil drive frequency using the 32.5 Hz and 42.5 Hz values to establish a noise level.
7.5
Optimizing flow reading in noisy applications
If the flow reading of the 8732EM is unstable, first check the wiring, grounding, and process
reference associated with the magnetic flowmeter system. Ensure that the following conditions
are met:

Ground straps are attached to the adjacent flange or ground ring

Grounding rings, lining protectors, or a process reference electrode are being used in
lined or non-conductive piping
The causes of unstable transmitter output can usually be traced to extraneous voltages on the
measuring electrodes. This “process noise” can arise from several causes including electrochemical reactions between the fluid and the electrode, chemical reactions in the process itself,
134
Digital Signal Processing
Reference Manual
Section 7: Digital Signal Processing
00809-0100-4444, Rev AD
August 2015
free ion activity in the fluid, or some other disturbance of the fluid/electrode capacitive layer. In
such noisy applications, an analysis of the frequency spectrum reveals process noise that
typically becomes significant below 15 Hz.
In some cases, the effects of process noise may be sharply reduced by elevating the coil drive
frequency above the 15 Hz region. The Rosemount 8732EM coil drive mode is selectable
between the standard 5 Hz and the noise-reducing 37 Hz.
7.5.1
Coil drive frequency
LOI menu path
Traditional fast keys
Device dashboard
Device Setup, Detailed Setup, Additional Params, Coil Drive Freq
1,4,1,1
2,2,8,3
This parameter changes the pulse rate of the magnetic coils.
5 Hz
The standard coil drive frequency is 5 Hz, which is sufficient for nearly all applications.
37 Hz
If the process fluid causes a noisy or unstable flow reading, increase the coil drive frequency to
37 Hz. If the 37 Hz mode is selected, perform the auto zero function for optimum performance.
7.5.2
Auto zero
LOI menu path
Traditional fast keys
Device dashboard
Device Setup, Diagnostics, Trims, Auto Zero
1,2,5,4
2,2,8,4
To ensure optimum accuracy when using 37 Hz coil drive mode, there is an auto zero function
that should be initiated. When using 37 Hz coil drive mode it is important to zero the system for
the specific application and installation.
The auto zero procedure should be performed only under the following conditions:

With the transmitter and sensor installed in their final positions. This procedure is not
applicable on the bench.

With the transmitter in 37 Hz coil drive mode. Never attempt this procedure with the
transmitter in 5 Hz coil drive mode.

With the sensor full of process fluid at zero flow.
These conditions should cause an output equivalent to zero flow.
Set the loop to manual if necessary and begin the auto zero procedure. The transmitter
completes the procedure automatically in about 90 seconds. A clock symbol will appear in the
lower right-hand corner of the display to indicate that the procedure is running.
Note
Failure to complete an auto zero may result in a flow velocity error of 5 to10% at1 ft/s (0.3 m/s).
While the output level will be offset by the error, the repeatability will not be affected.
Digital Signal Processing
135
Reference Manual
Section 7: Digital Signal Processing
00809-0100-4444, Rev AD
August 2015
7.5.3
Digital signal processing (DSP)
LOI menu path
Traditional fast keys
Device dashboard
Device Setup, Detailed Setup, Signal Processing
1,4,4
2,2,8,6
The 8732EM contains several advanced functions that can be used to stabilize erratic outputs
caused by process noise. The signal processing menu contains this functionality.
If the 37 Hz coil drive frequency has been set, and the output is still unstable, the damping and
signal processing function should be used. It is important to set the coil drive frequency to 37 Hz
to increase the flow sampling rate.
The 8732EM provides an easy and straightforward start-up, and also incorporates the capability
to deal with difficult applications that have previously manifested themselves in a noisy output
signal. In addition to selecting a higher coil drive frequency (37 Hz vs. 5 Hz) to isolate the flow
signal from the process noise, the 8732EM microprocessor can actually scrutinize each input
based on three user-defined parameters to reject the noise specific to the application.
Operating mode
LOI menu path
Traditional fast keys
Device dashboard
Device Setup, Detailed Setup, Signal Processing, Operating Mode
1,4,4,1
2,2,8,5
The operating mode should be used only when the signal is noisy and gives an unstable output.
Filter mode automatically uses 37 Hz coil drive mode and activates signal processing at the
factory set default values. When using filter mode, perform an auto zero with no flow and a full
sensor. Either of the parameters, coil drive mode or signal processing, may still be changed
individually. Turning signal processing off or changing the coil drive frequency to 5 Hz will
automatically change the operating mode from filter mode to normal mode.
This software technique, known as signal processing, “qualifies” individual flow signals based on
historic flow information and three user-definable parameters, plus an on/off control. These
parameters are described below.
Status
LOI menu path
Traditional fast keys
Device dashboard
Device Setup, Detailed Setup, Signal Processing, Main Config DSP, Status
1,4,4,2,1
2,2,8,6,1
Enable or disable the DSP capabilities. When ON is selected, the Rosemount 8732EM output is
derived using a running average of the individual flow inputs. Signal processing is a software
algorithm that examines the quality of the electrode signal against user-specified tolerances.
The three parameters that make up signal processing (number of samples, maximum percent
limit, and time limit) are described below.
Number of samples
LOI menu path
Traditional fast keys
Device dashboard
Device Setup, Detailed Setup, Signal Processing, Main Config DSP, Samples
1,4,4,2,2
2,2,8,6,2
The number of samples sets the amount of time that inputs are collected and used to calculate
the average value. Each second is divided into tenths with the number of samples equaling the
136
Digital Signal Processing
Reference Manual
Section 7: Digital Signal Processing
00809-0100-4444, Rev AD
August 2015
number of increments used to calculate the average. This parameter can be configured for an
integer value between 1 and 125. The default value is 90 samples.
For example:

A value of 1 averages the inputs over the past 1/10 second

A value of 10 averages the inputs over the past 1 second

A value of 100 averages the inputs over the past 10 seconds

A value of 125 averages the inputs over the past 12.5 seconds
Percent limit
LOI menu path
Traditional fast keys
Device dashboard
Device Setup, Detailed Setup, Signal Processing, Main Config DSP, % Limit
1,4,4,2,3
2,2,8,6,3
This parameter will set the tolerance band on either side of the running average, referring to
percent deviation from the average. Values within the limit are accepted while value outside the
limit are scrutinized to determine if they are a noise spike or an actual flow change. This
parameter can be configured for an integer value between 0 and 100 percent. The default value
is 2 percent.
Time limit
LOI menu path
Traditional fast keys
Device dashboard
Device Setup, Detailed Setup, Signal Processing, Main Config DSP, Time Limit
1,4,4,2,4
2,2,8,6,4
The time limit parameter forces the output and running average values to the new value of an
actual flow rate change that is outside the percent limit boundaries. It thereby limits response
time to flow changes to the time limit value rather than the length of the running average.
If the number of samples selected is 100, then the response time of the system is 10 seconds. In
some cases this may be unacceptable. Setting the time limit forces the 8732EM to clear the
value of the running average and re-establish the output and average at the new flow rate once
the time limit has elapsed. This parameter limits the response time added to the loop. A
suggested time limit value of two seconds is a good starting point for most applicable process
fluids. This parameter can be configured for a value between 0.6 and 256 seconds. The default
value is 2 seconds.
Digital Signal Processing
137
Reference Manual
Section 7: Digital Signal Processing
00809-0100-4444, Rev AD
August 2015
7.6
Explanation of signal processing algorithm
An example plotting flow rate versus time is given below to help visualize the signal processing
algorithm.
Figure 7-1. Signal Processing Functionality
Flow
Rate
Max
%
Limit
Time Limit
10 Samples = 1
Second
Time
X: Input flow signal from sensor.
O: Average flow signals and transmitter output, determined by the number of samples
parameter.
Tolerance band, determined by the percent limit parameter.
- Upper value = average flow + [(percent limit/100) average flow]
- Lower value = average flow - [(percent limit/100) average flow]
138
1.
This scenario is that of a typical non-noisy flow. The input flow signal is within the
percent limit tolerance band, therefore qualifying itself as a good input. In this case the
new input is added directly into the running average and is passed on as a part of the
average value to the output.
2.
This signal is outside the tolerance band and therefore is held in memory until the next
input can be evaluated. The running average is provided as the output.
3.
The previous signal currently held in memory is simply rejected as a noise spike since
the next flow input signal is back within the tolerance band. This results in complete
rejection of noise spikes rather than allowing them to be “averaged” with the good
signals as occurs in the typical analog damping circuits.
4.
As in number 2 above, the input is outside the tolerance band. This first signal is held in
memory and compared to the next signal. The next signal is also outside the tolerance
band (in the same direction), so the stored value is added to the running average as the
next input and the running average begins to slowly approach the new input level.
Digital Signal Processing
Reference Manual
00809-0100-4444, Rev AD
5.
Digital Signal Processing
Section 7: Digital Signal Processing
August 2015
To avoid waiting for the slowly incrementing average value to catch up to the new level
input, an algorithm is provided. This is the “time limit” parameter. The user can set this
parameter to eliminate the slow ramping of the output toward the new input level.
139
Section 7: Digital Signal Processing
August 2015
140
Reference Manual
00809-0100-4444, Rev AD
Digital Signal Processing
Section 8: Maintenance
Reference Manual
August 2015
00809-0100-4444, Rev AD
Section 8
Maintenance
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing a Local Operator Interface (LOI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing 8732EM revision 4 electronics stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing socket module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1
page 141
page 141
page 142
page 143
page 145
page 148
page 151
Introduction
This section covers basic transmitter maintenance. Instructions and procedures in this section
may require special precautions to ensure the safety of the personnel performing the
operations. Read the following safety messages before performing any operation described in
this section. Refer to these warnings when appropriate throughout this section.
8.2
Safety information
Failure to follow these maintenance guidelines could result in death or serious
injury.






Maintenance
Installation and servicing instructions should be performed by qualified personnel
only.
Do not perform any servicing other than that contained in the operating instructions.
Verify the operating environment of the sensor and transmitter is consistent with the
appropriate hazardous area approval.
Do not connect a Rosemount 8732EM to a non-Rosemount sensor that is located in an
explosive atmosphere.
Mishandling products exposed to a hazardous substance may result in death or
serious injury.
If the product being returned was exposed to a hazardous substance as defined by
OSHA, a copy of the required Material Safety Data Sheet (MSDS) for each hazardous
substance identified must be included with the returned goods.
141
Reference Manual
Section 8: Maintenance
00809-0100-4444, Rev AD
August 2015
8.3
Installing a Local Operator Interface (LOI)
Figure 8-1. Installing a Local Operator Interface (LOI)
142
1.
If the transmitter is installed in a control loop, secure the loop.
2.
Remove power from the transmitter.
3.
Remove the cover on the electronics compartment of the transmitter housing. If the
cover has a cover jam screw, loosen it before removing the cover. See “Cover jam screw”
on page 33 for details on the cover jam screw.
4.
On the electronics stack, locate the serial connection labeled “DISPLAY”. See Figure
8-1.
5.
Plug the serial connector from the back of the LOI into the receptacle on the electronics
stack. The LOI can be rotated in 90 degree increments to provide the best viewing
position. Rotate the LOI to the desired orientation, taking care to not exceed 360
degrees of rotation. Exceeding 360 degrees of rotation could damage the LOI cable
and/or connector.
6.
Once the serial connector is installed on the electronics stack, and the LOI is oriented in
the desired position, tighten the three mounting screws.
7.
Install the extended cover with the glass viewing pane and tighten to metal-to-metal
contact. If the cover has a cover jam screw, this must be tightened to comply with
installation requirements. Return power to the transmitter and verify that it is
functioning correctly and reporting the expected flow rate.
8.
If installed in a control loop, return the loop to automatic control.
Maintenance
Reference Manual
Section 8: Maintenance
00809-0100-4444, Rev AD
8.4
August 2015
Replacing 8732EM revision 4 electronics stack
Prior to installing the replacement electronics stack, it is important to verify that the transmitter
housing you have is of the correct design to accept the Revision 4 electronics.
Follow the steps below to confirm the transmitter housing is compatible with this electronics
kit.
1.
Verify the model number is 8732EM. If the transmitter model is not 8732EM, then
these electronics are not compatible. See Figure 8-2 for the location of the model
number. If the model is 8732C, 8742C, 8732ES, or some other model, then these
electronics are not compatible with the enclosure. If you have one of these
transmitters, a full replacement transmitter will be required. Consult the 8700M
Product Data Sheet (00813-0100-4444) for details on ordering a new transmitter.
Figure 8-2. Transmitter Nameplate Location
Maintenance
143
Reference Manual
Section 8: Maintenance
00809-0100-4444, Rev AD
August 2015
2.
Verify the electronics board inside the housing is green and looks like the board
pictured on the left in Figure 8-3. If the board is not green, or does not look like the
board pictured, then the electronics are not compatible.
Figure 8-3. Transmitter Housing Electronics Board Identification
3.
Confirm the electronics stack is for an 8732EM transmitter. Refer to the picture on the
left in Figure 8-4.
Figure 8-4. Electronics Stack Identification
144
Maintenance
Reference Manual
00809-0100-4444, Rev AD
8.5
Section 8: Maintenance
August 2015
Replacing socket module
The socket module connects the sensor adapter to the transmitter. There are two versions of
the socket module - one for integral mount transmitters and one for remote mount
transmitters. The socket module is a replaceable component.
To remove the socket module, loosen the two mounting screws and pull up on the socket
module from the base. When removing the socket module, do not pull on the wires. See
Figure 8-5.
Figure 8-5. Socket Module Warning
8.5.1
Integral mount socket module
The integral mount socket module is shown in Figure 8-6. To gain access to the socket module,
the transmitter must be removed from the sensor adapter.
Figure 8-6. Socket Module—Integral Mount
Maintenance
145
Reference Manual
Section 8: Maintenance
00809-0100-4444, Rev AD
August 2015
Removing integral mount socket module
1.
Disconnect power.
2.
Remove electronics cover to gain access to the coil and electrode cables.
3.
If the transmitter has an LOI, it will need to be removed to gain access to the coil and
electrode cables.
4.
Disconnect the coil and electrode cables.
5.
Remove the four transmitter mounting screws.
6.
Lift the transmitter off of the sensor adapter.
7.
To remove the socket module, loosen the two mounting screws and pull up on the
socket module from the base.
8.
When removing the socket module, do not pull on the wires. See Figure 8-5.
Installing integral mount socket module
146
1.
To insert a new integral mount socket module, press the base into its keyed position
and tighten the two mounting screws.
2.
The coil and electrode cables are fed through the bottom opening of the transmitter
and plugged into the face of the electronics.
3.
The coil and electrode cables are keyed so they will only fit into their dedicated location.
4.
If the transmitter has an LOI, it will need to be removed to access the coil and electrode
ports.
5.
Once the connections are made, the transmitter can be secured to the sensor adapter
using the four mounting bolts.
Maintenance
Reference Manual
Section 8: Maintenance
00809-0100-4444, Rev AD
8.5.2
August 2015
Replacing terminal block socket module
The terminal block socket module is shown in Figure 8-7. To gain access to the socket module,
remove the junction box from the sensor adapter.
Figure 8-7. Socket Module—Terminal Block
Removing terminal block socket module
Maintenance
1.
Disconnect power to the transmitter and the remote cabling connected to the terminal
block.
2.
Remove the junction box cover to gain access to the remote cabling.
3.
To disconnect the terminal block from the junction box housing, remove the two
mounting screws and the two divider mounting screws (if applicable).
4.
Pull up on the terminal block to expose the socket module base.
5.
To remove the socket module, loosen the two mounting screws and pull up on the
socket module from the base.
6.
When removing the socket module, do not pull on the wires. See Figure 8-5.
147
Reference Manual
Section 8: Maintenance
00809-0100-4444, Rev AD
August 2015
Installing terminal block socket module
8.6
1.
Insert the new terminal block socket module, press the base into its keyed position, and
tighten the two mounting screws.
2.
Connect the terminal block to the junction box housing by tightening the two
mounting screws. Install the divider with the two mounting screws if applicable.
3.
Reconnect remote cabling and power and replace junction box cover.
Trims
LOI menu path
Diagnostics, Trims
Traditional fast keys
1,2,5
Device dashboard
3,4
Trims are used to calibrate the analog loop, calibrate the transmitter, re-zero the transmitter,
and calibrate the transmitter with another manufacturer's sensor. Proceed with caution
whenever performing a trim function.
8.6.1
D/A trim
LOI menu path
Diagnostics, Trims, D/A Trim
Traditional fast keys
1,2,5,1
Device dashboard
3,4,4,5
The D/A trim is used to calibrate the 4-20mA analog loop output from the transmitter. For
maximum accuracy, the analog output should be trimmed for your system loop. Use the
following steps to complete the output trim function.
1.
Set the loop to manual, if necessary.
2.
Connect a precision ammeter in the 4-20mA loop.
3.
Initiate the D/A trim function with the LOI or Handheld Communicator.
4.
Enter the 4mA meter value when prompted.
5.
Enter the 20mA meter value when prompted.
6.
Return the loop to automatic control, if necessary.
The 4-20mA trim is now complete. The D/A trim can be repeated to check the results.
Alternatively, the analog output test can also be used to verify loop performance.
148
Maintenance
Reference Manual
Section 8: Maintenance
00809-0100-4444, Rev AD
8.6.2
August 2015
Scaled D/A trim
LOI menu path
Diagnostics, Trims, Scaled D/A Trim
Traditional fast keys
1,2,5,2 or 1,4,2,1,7
Device dashboard
3,4,4,6
A scaled D/A trim enables calibration of the flowmeter analog output using a different scale than
the standard 4-20mA output scale. Non-scaled D/A trimming (described above), is typically
performed using an ammeter where calibration values are entered in units of milliamperes.
Scaled D/A trimming enables trimming of the flowmeter using a scale that may be more
convenient based upon the method of measurement.
For example, it may be more convenient to make current measurements by direct voltage
readings across the loop resistor. If the loop resistor is 500 ohms, and calibration of the meter
will be done using voltage measurements across this resistor, the trim points can be rescaled
from 4-20mA to 4-20mA x 500 ohm or 2-10VDC. Once the scaled trim points have been entered
as 2 and 10, calibration of the flowmeter can be done by entering voltage measurements
directly from the voltmeter.
8.6.3
Digital trim
LOI menu path
Device Setup, Diagnostics, Trims, Digital Trim
Traditional fast keys
1,2,5,3
Device dashboard
3,4,5
Digital trim is the function by which the factory calibrates the transmitter. This procedure is
rarely needed by users. It is only necessary if the Rosemount 8732EM is suspected to be no
longer accurate. A Rosemount 8714D Calibration Standard is required to complete a digital
trim. Attempting a digital trim without a Rosemount 8714D Calibration Standard may result in
an inaccurate transmitter or an error message. The digital trim must be performed with the coil
drive mode set to 5Hz and with a nominal sensor calibration number stored in the memory.
Note
Attempting a digital trim without a Rosemount 8714D Calibration Standard may result in an
inaccurate transmitter, or a “DIGITAL TRIM FAILURE” message may appear. If this message
occurs, no values were changed in the transmitter. Simply cycle power on the Rosemount
8732EM to clear the message.
To simulate a nominal sensor with the Rosemount 8714D Calibration Standard, change/verify
the following five parameters in the Rosemount 8732EM:
Maintenance

Calibration Number-1000015010000000

Units-ft/s

PV URV-20mA = 30.00 ft/s

PV LRV-4mA = 0 ft/s

Coil Drive Frequency-5Hz
149
Reference Manual
Section 8: Maintenance
00809-0100-4444, Rev AD
August 2015
Note
Before changing any of the configuration parameters, be sure to record the original values so
that the transmitter can be returned to the original configuration prior to being placed back into
operation. Failure to return the settings to the original configuration will result in incorrect flow
and totalizer readings.
The instructions for changing the calibration number, units, PV URV, and PV LRV are located in
“Basic setup” on page 34. Instructions for changing the coil drive frequency can be found on
“Coil drive frequency” on page 135.
Set the loop to manual (if necessary) and then complete the following steps:
8.6.4
1.
Power down the transmitter.
2.
Connect the transmitter to a Rosemount 8714D Calibration Standard.
3.
Power up the transmitter with the Rosemount 8714D connected and read the flow rate.
The electronics need about a 5-minute warm-up time to stabilize.
4.
Set the 8714D Calibration Standard to the 30 ft/s (9.1 m/s) setting.
5.
The flow rate reading after warm-up should be between 29.97 (9.1 m/s) and 30.03 ft/s
(9.2 m/s).
6.
If the reading is within the range, return the transmitter to the original configuration
parameters.
7.
If the reading is not within this range, initiate a digital trim with the LOI or Handheld
Communicator. The digital trim takes about 90 seconds to complete. No transmitter
adjustments are required.
Universal trim
LOI menu path
Device Setup, Diagnostics, Trims, Universal Trim
Traditional fast keys
1,2,5,5
Device dashboard
2,4,1
The universal auto trim function enables the Rosemount 8732EM to calibrate sensors that were
not calibrated at the Rosemount factory. The function is activated as one step in a procedure
known as in-process calibration. If a Rosemount sensor has a 16-digit calibration number,
in-process calibration is not required. If it does not, or if the sensor is made by another
manufacturer, complete the following steps for in-process calibration. Refer to Appendix D
Implementing a Universal Transmitter.
1.
Determine the flow rate of the process fluid in the sensor.
Note
The flow rate in the line can be determined by using another sensor in the line, by counting the
revolutions of a centrifugal pump, or by performing a bucket test to determine how fast a given
volume is filled by the process fluid.
2.
150
Complete the universal auto trim function.
Maintenance
Reference Manual
Section 8: Maintenance
00809-0100-4444, Rev AD
August 2015
When the routine is completed, the sensor is ready for use.
8.7
Review
LOI menu path
Device Setup, Review
Traditional fast keys
1,5
Device dashboard
N/A
The 8732EM includes a capability to review the configuration variable settings.
The flowmeter configuration parameters set at the factory should be reviewed to ensure
accuracy and compatibility with the particular application of the flowmeter.
Note
If the LOI is used to review variables, each variable must be accessed as if changing its setting.
The value displayed on the LOI screen is the configured value of the variable.
Maintenance
151
Section 8: Maintenance
August 2015
152
Reference Manual
00809-0100-4444, Rev AD
Maintenance
Section 9: Troubleshooting
Reference Manual
August 2015
00809-0100-4444, Rev AD
Section 9
Troubleshooting
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation check and guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1
page 153
page 154
page 154
page 157
page 166
page 169
Introduction
This section covers basic transmitter and sensor troubleshooting. Problems in the magnetic
flowmeter system are usually indicated by incorrect output readings from the system, error
messages, or failed tests. Consider all sources when identifying a problem in the system. If the
problem persists, consult the local Rosemount representative to determine if the material
should be returned to the factory. Emerson Process Management offers several diagnostics that
aid in the troubleshooting process. Instructions and procedures in this section may require
special precautions to ensure the safety of the personnel performing the operations. Read the
following safety messages before performing any operation described in this section. Refer to
these warnings when appropriate throughout this section.
The Rosemount 8732EM performs self-diagnostics on the entire magnetic flowmeter system:
the transmitter, the sensor, and the interconnecting wiring. By sequentially troubleshooting
each individual piece of the magmeter system, it becomes easier to identify the problem and
make the appropriate adjustments.
If there are problems with a new magmeter installation, see 9.3 Installation check and guide
below for a quick guide to solve the most common installation problems. For existing magmeter
installations, Table on page 166 lists the most common magmeter problems and corrective
actions.
Troubleshooting
153
Section 9: Troubleshooting
9.2
Reference Manual
00809-0100-4444, Rev AD
August 2015
Safety information
Failure to follow these troubleshotting guidelines could result in death or serious
injury.






9.3
Installation and servicing instructions should be performed by qualified personnel
only.
Do not perform any servicing other than that contained in the operating instructions.
Verify that the operating environment of the sensor and transmitter is consistent with
the appropriate hazardous area approval.
Do not connect a Rosemount 8732EM to a non-Rosemount sensor that is located in an
explosive atmosphere.
Mishandling products exposed to a hazardous substance may result in death or
serious injury.
If the product being returned was exposed to a hazardous substance as defined by
OSHA, a copy of the required Material Safety Data Sheet (MSDS) for each hazardous
substance identified must be included with the returned goods.
Installation check and guide
Use this guide to check new installations of Rosemount magnetic flowmeter systems that
appear to malfunction.
9.3.1
Transmitter
Before applying power to the magnetic flowmeter system, make the following transmitter
checks:
154
1.
Record the transmitter model number and serial number.
2.
Visually inspect the transmitter for any damage including the terminal block.
3.
Verify the proper wiring connections have been made for the power and outputs.
Troubleshooting
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
Apply power to the magnetic flowmeter system before making the following transmitter
checks:
9.3.2
1.
Check for an active error message or status alert. Refer to 9.4 Diagnostic messages.
2.
Verify the correct sensor calibration number is entered in the transmitter. The
calibration number is listed on the sensor nameplate.
3.
Verify the correct sensor line size is entered in the transmitter. The line size value is
listed on the sensor nameplate.
4.
Verify the analog range of the transmitter matches the analog range in the control
system.
5.
Verify the forced analog output and forced pulse output of the transmitter produces
the correct output at the control system.
6.
If desired, use a Rosemount 8714D to verify the transmitter calibration.
Sensor
Be sure that power to magnetic flowmeter system is removed before beginning the following
sensor checks:
Troubleshooting
1.
Record the sensor model number and serial number.
2.
Visually inspect the sensor for any damage including inside the remote junction box, if
applicable.
3.
For horizontal flow installations, ensure that the electrodes remain covered by process
fluid. For vertical or inclined installations, ensure that the process fluid is flowing up into
the sensor to keep the electrodes covered by process fluid.
4.
Verify the flow arrow is pointing in the same direction as forward flow.
5.
Ensure the grounding straps on the sensor are connected to grounding rings, lining
protectors, or the adjacent pipe flanges. Improper grounding will cause erratic
operation of the system. Sensors with a ground electrode will not require the
grounding straps to be connected.
155
Section 9: Troubleshooting
9.3.3
Reference Manual
00809-0100-4444, Rev AD
August 2015
Remote wiring
1.
The electrode signal and coil drive wires must be separate cables, unless Rosemount
specified combo cable is used. See 2.12 Wiring the transmitter.
2.
The electrode signal wire and coil drive wire must be twisted shielded cable.
Rosemount recommends 20 AWG twisted shielded cable for the electrode signal and
14 AWG twisted shielded cable for the coil drive. See 2.12 Wiring the transmitter.
3.
See Appendix B Product Certifications regarding wiring installation requirements.
4.
See Appendix C Wiring Diagrams for component and/or combination cable wiring.
5.
Verify there is minimal exposed wiring and shielding. Less than 1 inch (25 mm) is
recommended.
6.
The single conduit that houses both the electrode signal and coil drive cables should
not contain any other wires. This includes wires from other magmeters.
Note
For installations requiring intrinsically safe electrodes, the signal and coil drive cables must be
run in Individual conduits.
9.3.4
156
Process fluid
1.
The process fluid should have a minimum conductivity of 5 microSiemens/cm (5 micro
mhos/cm).
2.
The process fluid must be free of air and gas.
3.
The sensor must be full of process fluid.
4.
The process fluid must be compatible with the wetted materials - liner, electrodes,
ground rings, and lining protectors. Refer to the “Rosemount Magnetic Flowmeter
Material Selection Guide” (00816-0100-3033) Technical Note for details.
5.
If the process is electrolytic or has cathodic protection, refer to the “Installation and
Grounding of Magmeters in Typical and Special Applications” (00840-2400-4727)
Technical Note for special installation requirements.
Troubleshooting
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
9.4
August 2015
Diagnostic messages
Problems in the magnetic flowmeter system are usually indicated by incorrect output readings
from the system, error messages, or failed tests. Consider all sources in identifying a problem in
the system.
Table 9-1. Basic Diagnostic Messages
Error message
Empty Pipe
Coil Open Circuit
Auto Zero Failure
Potential cause
Corrective action
Empty pipe
• None - message will clear when pipe is full
Wiring error
• Check that wiring matches appropriate wiring diagrams
Electrode error
• Perform sensor tests - see Table 9-8 on page 172
Conductivity less than 5
microSiemens per cm
• Increase conductivity to greater than or equal to 5 microSiemens per
cm
Intermittent diagnostic
• Adjust tuning of empty pipe parameters - see Section 8.4.1
Improper wiring
• Check coil drive wiring and sensor coils
Perform sensor tests - see Table 9-8 on page 172
Other manufacturer’s sensor
• Change coil current to 75 mA - set calibration numbers to
10000550100000030
• Perform a universal auto-trim to select the proper coil current
Electronics board failure
• Replace 8732EM electronics stack
Coil circuit open fuse
• Return the unit to the factory for fuse replacement
Flow is not set to zero
• Force flow to zero, perform auto zero trim
Unshielded cable in use
• Change wire to shielded cable
Moisture problems
• See Table 9-8 on page 172
No flow in pipe while performing
Universal Auto Trim
• Establish a known flow rate, and perform universal auto-trim
calibration
Wiring error
• Check that wiring matches appropriate wiring diagrams - see
Implementing a Universal Transmitter on page 237
Flow rate is changing in pipe while
performing Universal Auto-Trim
routine
Flow rate through sensor is
significantly different than value
entered during Universal Auto-Trim
routine
Incorrect calibration number entered
into transmitter for Universal
Auto-Trim routine
• Establish a constant flow rate, and perform universal auto-trim
calibration
Wrong sensor size selected
• Correct sensor size setting - see Line size on page 34
Sensor failure
• Perform sensor tests - see Table 9-8 on page 172
Electronics Failure
Electronics self check failure
• Cycle power to see if diagnostic message clears
• Replace Electronics stack
Electronics Temp Fail
Ambient temperature exceeded the
electronics temperature limits
• Move transmitter to a location with an ambient temperature range of
-40 to 140 °F (-40 to 60 °C)
Electrode or coil wires reverse
• Verify wiring between sensor and transmitter
Flow is reverse
• Turn ON Reverse Flow Enable to read flow
Sensor installed backwards
• Install sensor correctly, or switch either the electrode wires (18 and 19)
or the coil wires (1 and 2)
External voltage applied to terminals
5 and 6
• Remove voltage to turn PZR off
Auto-Trim Failure
Reverse Flow
PZR Activated
(Positive Zero Return)
Troubleshooting
• Verify flow in sensor and perform universal auto-trim calibration
• Replace sensor calibration number with 1000005010000000
157
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
Table 9-1. Basic Diagnostic Messages (continued)
Error message
Potential cause
Corrective action
Pulse Out of Range
The transmitter is trying to generate
a frequency greater than allowed
• Standard pulse - increase pulse scaling to prevent pulse output from
exceeding 11,000 Hz
• Intrinsically safe pulse - Increase pulse scaling to prevent pulse output
from exceeding 5,500 Hz
• Pulse output is in fixed pulse mode and is trying to generate a
frequency greater than the pulse width can support - see Pulse width
on page 91
• Verify the sensor calibration number and line size are correctly entered
in the electronics
Analog Out of Range
Flow rate is greater than analog
output range
• Reduce flow, adjust URV and LRV values
• Verify the sensor calibration number and line sizes are correctly entered
in the electronics
Flowrate > 43 ft/sec
Digital Trim Failure
(Cycle power to clear
messages, no changes
were made)
Coil Over Current
Coil Power Limit
Flow rate is greater than 43 ft/sec
• Lower flow velocity, increase pipe diameter
Improper wiring
• Check coil drive wiring and sensor coils
• Perform sensor tests - see Table 9-8 on page 172
The calibrator (8714B/C/D) is not
connected properly
Incorrect calibration number entered
into transmitter
158
• Replace sensor calibration number with 1000015010000000
Calibrator is not set to 30 FPS
• Change calibrator setting to 30 FPS
Bad calibrator or calibrator cable
• Replace calibrator and/or calibrator cable
Improper wiring
• Check coil drive wiring and sensor coils
Perform sensor tests - see Table 9-8 on page 172
Transmitter failure
• Replace the electronics stack
Improper wiring
• Check coil drive wiring and sensor coils
Perform sensor tests - see Table 9-8 on page 172
Incorrect calibration number
• Verify configured calibration number matches sensor tag
Transmitter connected to other
manufacturer’s sensor
• Change coil current to 75 mA - set calibration number to
10000550100000030
• Perform a universal auto-trim to select the proper coil current
Coil drive frequency set to 37 Hz
• Sensor may not be compatible with 37 Hz. Switch coil drive frequency
to 5 Hz.
Sensor failure
• Perform sensor tests - see Table 9-8 on page 172
Improper wiring
• Check the analog loop wiring - see Wiring the transmitter on page 23
No external loop power
• Verify the analog power switch position (internal/external)
• For externally powered loop, verify power supply requirements - see
Powering the transmitter on page 31
No loop resistance (open loop)
• Install resistance across the analog output terminals
• Disable message using LOI Error Mask parameter
No AO Power
Electrode Saturation
• Review calibrator connections
Transmitter failure
• Replace the electronics stack
Improper wiring
• See Wiring the transmitter on page 23
Improper process reference
• See Process reference connection on page 19
Improper earth grounding
• Verify earth ground connections - see Wiring the transmitter on
page 23
Application requires special
transmitter
• Replace transmitter with transmitter that includes special option F0100
Troubleshooting
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
Table 9-2. Advanced Process Diagnostic Messages
Error message
Grounding/Wiring Fault
High Process Noise
Electrode Coating Level 1
Electrode Coating Level 2
Troubleshooting
Potential cause
Corrective action
Improper installation of wiring
• See Wiring the transmitter on page 23
Coil/electrode shield not connected
• See Wiring the transmitter on page 23
Improper process grounding
• See Process reference connection on page 19
Faulty ground connection
• Check wiring for corrosion, moisture in the terminal block -see
Process reference connection on page 19
Sensor not full
• Verify sensor is full
• Enable empty pipe detection
Slurry flows - mining/pulp stock
• Decrease the flow rate below 10 ft/s (3 m/s)
• Complete the possible solutions listed under Troubleshooting high
process noise on page 163
Chemical additives upstream of the
sensor
• Move injection point downstream of the sensor or move the sensor to
a new location
• Complete the possible solutions listed under Troubleshooting high
process noise on page 163
Electrode not compatible with the
process fluid
• Refer to the Rosemount Magnetic Flowmeter Material Selection Guide
(00816-0100-3033)
Gas/air in line
• Move the sensor to another location in the process line to ensure that
it is full under all conditions
Electrode coating
• Enable coated electrode etection diagnostic
• Use bullet-nose electrodes
• Downsize sensor to increase flowrate above 3 ft/s (1 m/s)
• Periodically clean sensor
Styrofoam or other insulating
particles
• Complete the possible solutions listed under Troubleshooting high
process noise on page 163
• Consult factory
Low conductivity fluids
(below 10 microsiemens/cm)
• Trim electrode and coil wires - see Sensor installation on page 12
• Use integral mount transmitter
• Set coil drive frequency to 37Hz
Coating is starting to buildup on
electrode and interfering with
measurement signal
• Schedule maintenance to clean electrode
• Use bullet nose electrodes
• Downsize sensor to increase flow rate above 3ft/s (1ms)
Process fluid conductivity has
changed
• Verify process fluid conductivity
Coating has built-up on electrode
and is interfering with measurement
signal
• Schedule maintenance to clean electrode
• Use bullet nose electrodes
• Downsize sensor to increase flow rate above 3ft/s (1ms)
Process fluid conductivity has
changed
• Verify process fluid conductivity
159
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
Table 9-3. Advanced Meter Verification Messages
Error message
Potential cause
Transmitter calibration verification
test failed
• Verify pass/fail criteria
• Rerun SMART™ Meter Verification (8714i) under no flow conditions
• Verify calibration using 8714 Calibration Standard
• Perform digital trim
• Replace electronics board
Sensor calibration test failed
• Verify pass/fail criteria
• Rerun SMART Meter Verification (8714i)
• Perform sensor tests - see Table 9-8 on page 172
Sensor coil circuit test failed
• Verify pass/fail criteria
• Rerun SMART Meter Verification (8714i)
• Perform sensor tests - see Table 9-8 on page 172
Sensor electrode circuit test failed
• Verify electrode resistance has a baseline (signature) value from a full
pipe baseline
• Verify test condition was selected properly
• Verify pass/fail criteria
• Rerun SMART Meter Verification (8714i)
• Perform sensor tests - see Table 9-8 on page 172
Analog loop not powered
• Check 4-20 mA internal/external loop power switch - see
Internal/external analog power on page 40
• Check external supply voltage to the transmitter
• Check for parallel paths in the current loop
Transmitter failure
• Perform transmitter self test
• Perform manual analog loop test and D/A trim if necessary
• Replace the electronics board
Transmitter calibration verification
test failed
• Verify pass/fail criteria
• Run manual SMART Meter Verification (8714i) under no flow conditions
• Verify calibration using 8714D Calibration Standard
• Perform digital trim
• Replace electronics stack
Sensor calibration test failed
• Run manual SMART Meter Verification (8714i)
• Perform sensor tests - see Table 9-8 on page 172
Sensor coil circuit test failed
• Run manual SMART Meter Verification (8714i)
• Perform sensor tests - see Table 9-8 on page 172
Sensor electrode circuit test failed
• Run manual SMART Meter Verification (8714i)
• Perform sensor tests - see Table 9-8 on page 172
• Verify electrode resistance has a signature value from a full pipe
baseline
Unstable flow rate during the
verification test or noisy process
• Run manual transmitter verification test with no flow and a full pipe
Transmitter drift or faulty
electronics
• Verify transmitter electronics with 8714D Calibration Standard. The
dial on the 8714D should be set to 30 ft/s (9.14 m/s). The transmitter
should be set up with the nominal calibration number
(1000015010000000) and 5 Hz coil drive frequency.
• Perform an electronics trim using the 8714
• If the electronics trim doesn't correct the issue, replace the electronics
Moisture in the terminal block of the
sensor or shorted coil
• Perform sensor tests - see Table 9-8 on page 172
• If the problem persists, replace the sensor
Moisture in the terminal block of the
sensor or shorted coil
• Perform sensor tests - see Table 9-8 on page 172
• If the problem persists, replace the sensor
Calibration shift caused by heat
cycling or vibration
• Perform sensor tests - see Table 9-8 on page 172
• If the problem persists, replace the sensor
8714i Failed
4-20 mA loop
verification failed
Continuous Meter
Verification Error
Simulated Velocity Out of
Spec
Coil Resistance Out of
Spec
Coil Signature Out of Spec
160
Corrective action
Troubleshooting
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
Table 9-3. Advanced Meter Verification Messages (continued)
Error message
Electrode Resistance Out
of Spec
Analog Output Out of
Spec
Troubleshooting
Potential cause
Corrective action
Moisture in the terminal block of the
sensor
• Perform sensor tests - see Table 9-8 on page 172
• If the problem persists, replace the sensor
Electrode coating
• Enable coated electrode detection diagnostic
• Use bullet-nose electrodes
• Downsize sensor to increases flowrate above 3 ft/s (1 m/s)
• Periodically clean sensor
Shorted electrodes
• Perform sensor tests - see Table 9-8 on page 172
• If the problem persists, replace the sensor
Unstable flow rate during the
verification test or noisy process
• Run manual transmitter verification test with no flow and a full pipe
Analog output is no longer within
accuracy specifications
• Check the analog loop wiring. Excessive loop resistance can cause an
invalid test
161
Section 9: Troubleshooting
9.4.1
Reference Manual
00809-0100-4444, Rev AD
August 2015
Troubleshooting empty pipe
The following actions can be taken if empty pipe detection is unexpected:
9.4.2
1.
Verify the sensor is full.
2.
Verify the sensor has not been installed with a measurement electrode at the top of the
pipe.
3.
Decrease the sensitivity by setting the empty pipe trigger level to a value of at least 20
counts above the empty pipe value read with a full pipe.
4.
Decrease the sensitivity by increasing the empty pipe counts to compensate for process
noise. The empty pipe counts is the number of consecutive empty pipe value readings
above the empty pipe trigger level required to set the empty pipe diagnostic. The count
range is 2-50, factory default set at 5.
5.
Increase process fluid conductivity above 50 microsiemens/cm.
6.
Properly connect the wiring between the sensor and the transmitter. Corresponding
terminal block numbers in the sensor and transmitter must be connected.
7.
Perform the sensor electrical resistance tests. For more detailed information, consult
Table 9-8 on page 172.
Troubleshooting ground/wiring fault
If transmitter detects high levels (greater than 5mV) 50/60 Hz noise caused by improper wiring
or poor process grounding:
162
1.
Verify the transmitter is earth grounded.
2.
Connect ground rings, grounding electrode, lining protector, or grounding straps.
Grounding diagrams can be found in Process reference connection on page 19.
3.
Verify the sensor is full.
4.
Verify wiring between sensor and transmitter is prepared properly. Shielding should be
stripped back less than 1 inch (25 mm).
5.
Use separate shielded twisted pairs for wiring between sensor and transmitter.
6.
Properly connect the wiring between the sensor and the transmitter. Corresponding
terminal block numbers in the sensor and transmitter must be connected.
Troubleshooting
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
9.4.3
August 2015
Troubleshooting high process noise
The transmitter detected high levels of process noise. If the signal to noise ratio is less than 25
while operating in 5 Hz mode, proceed with the following steps:
1.
Increase transmitter coil drive frequency to 37 Hz (refer to Coil drive frequency on
page 135) and, if possible, perform auto zero function (Auto zero on page 135).
2.
Verify sensor is electrically connected to the process with process reference electrode,
grounding rings with grounding straps, or lining protector with grounding straps.
3.
If possible, redirect chemical additions downstream of the magmeter.
4.
Verify process fluid conductivity is above 10 microSiemens/cm.
If the signal to noise ratio is less than 25 while operating in 37 Hz mode, proceed with the
following steps:
1.
Turn on the Digital Signal Processing (DSP) technology and follow the setup procedure
(see Section 7 Digital Signal Processing). This will minimize the level of damping in the
flow measurement and control loop while also stabilizing the reading to minimize valve
actuation.
2.
Increase damping to stabilize the signal (refer to PV damping on page 35). This will add
response time to the control loop.
3.
Move to a Rosemount High-Signal flowmeter system. This flowmeter will deliver a
stable signal by increasing the amplitude of the flow signal by ten times to increase the
signal to noise ratio. For example if the signal to noise ratio (SNR) of a standard
magmeter is 5, the High-Signal would have a SNR of 50 in the same application. The
Rosemount High-Signal system is comprised of the 8707 sensor which has modified
coils and magnetics and the 8712H High-Signal transmitter.
Note
In applications where very high levels of noise are a concern, it is recommended that a
dual-calibrated Rosemount High-Signal 8707 sensor be used. These sensors can be calibrated to
run at lower coil drive current supplied by the standard Rosemount transmitters, but can also be
upgraded by changing to the 8712H High-Signal transmitter.
1/f noise
This type of noise has higher amplitudes at lower frequencies, but generally degrades over
increasing frequencies. Potential sources of 1/f noise include chemical mixing and slurry flow
particles rubbing against the electrodes. This type of noise can be mitigated by switching to the
37Hz coil drive frequency.
Spike noise
This type of noise generally results in a high amplitude signal at specific frequencies which can
vary depending on the source of the noise. Common sources of spike noise include chemical
injections directly upstream of the flowmeter, hydraulic pumps, and slurry flows with low
concentrations of particles in the stream. The particles bounce off of the electrode generating a
“spike” in the electrode signal. An example of this type of flow stream would be a recycle flow in
Troubleshooting
163
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
a paper mill. The type of noise can be mitigated by switching to the 37Hz coil drive frequency
and enabling the digital signal processing.
White noise
This type of noise results in a high amplitude signal that is relatively constant over the frequency
range. Common sources of white noise include chemical reactions or mixing that occurs as the
fluid passes through the flowmeter and high concentration slurry flows where the particulates
are constantly passing over the electrode head. An example of this type of flow stream would be
a basis weight stream in a paper mill. This type of noise can be mitigated by switching to the
37Hz coil drive frequency and enabling the digital signal processing.
9.4.4
Troubleshooting coated electrode detection
In the event that electrode coating is detected, use the following table to determine the
appropriate course of action.
Table 9-4. Troubleshooting the Electrode Coating Diagnostic
Error message
Potential causes of error
Steps to correct
Electrode Coating Level 1
• Insulating coating is starting to build up on
the electrode and may interfere with the
flow measurement signal
• Process fluid conductivity has decreased to
a level close to operational limits of the
meter
• Verify process fluid conductivity
• Schedule maintenance to clean the electrodes
• Use bullet nose electrodes
• Replace the meter with a smaller diameter meter to
increase the flow velocity to above 3 ft/s (1 m/s)
Electrode Coating Level 2
• Insulating coating has built up on the
electrodes and is interfering with the flow
measurement signal
• Process fluid conductivity has decreased to
a level below the operational limits of the
meter
• Verify process fluid conductivity
• Schedule maintenance to clean the electrodes
• Use bullet nose electrodes
• Replace the meter with a smaller diameter meter to
increase the flow velocity to above 3 ft/s (1 m/s)
9.4.5
Troubleshooting 4-20 mA loop verification
In the event that the 4-20 mA Loop Verification fails, use the following table to determine the
appropriate course of action.
Table 9-5. Troubleshooting the Analog Loop Verification Diagnostic
Test
Potential cause
• Check analog loop wiring
• Check loop resistance
• Check analog loop power switch – see Internal/external
analog power on page 40
• Check external supply voltage to the transmitter
• Check for parallel paths in the current loop
• Analog drift
• Perform D/A trim
• Transmitter failure
• Perform transmitter self-test
• Perform manual analog loop test
• Replace the electronics stack
4-20 mA Loop Verification Failure
164
Corrective action
• Analog loop not powered
Troubleshooting
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
9.4.6
August 2015
Troubleshooting the SMART Meter Verification test
If the SMART Meter Verification test fails, use the following table to determine the appropriate
course of action. Begin by reviewing the SMART Meter Verification results to determine the
specific test that failed.
Table 9-6. Troubleshooting the SMART Meter Verification Diagnostic
Test
Potential cause
Corrective action
• Unstable flow reading during the test
• Noise in the process
• Transmitter drift
• Faulty electronics
• Rerun SMART Meter Verification (8714i) under No Flow
conditions
• Check the transmitter calibration with the 8714D
Calibration Standard
• Perform a digital trim
• Replace the electronics stack
Sensor Calibration Verification
• Moisture in the sensor terminal block
• Calibration shift caused by heat
cycling or vibration
Coil Circuit Health
• Moisture in the sensor terminal block
• Shorted Coil
• Rerun SMART Meter Verification (8714i)
• Perform the sensor checks detailed in 9.6 Sensor
troubleshooting.
• Remove the sensor and send back for evaluation and / or
recalibration
Electrode Circuit Health
• Electrode resistance baseline was not
taken after installation
• Test condition was not selected
properly
• Moisture in the sensor terminal block
• Coated electrodes
• Shorted electrodes
Transmitter Verification Test
Troubleshooting
165
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
9.5
Basic troubleshooting
When troubleshooting a magmeter, it is important to identify the issue. Table 9-7 provides
common symptoms displayed by a magmeter that is not functioning properly. This table
provides potential causes and suggested corrective actions for each symptom.
Table 9-7. Common Magmeter Issue
Symptom
Output at 0 mA
Output at 4 mA
Output will not reach 20 mA
Potential cause
• No power to transmitter
• Check power source and connections to the transmitter
• Analog output improperly
configured
• Check the analog power switch position
• Verify wiring and analog power
• Electronics failure
• Verify transmitter operation with an 8714D Calibration Standard or
replace the electronic stack
• Blown fuse
• Check the fuse and replace with an appropriately rated fuse, if
necessary
• Transmitter in multidrop mode
• Configure Poll Address to 0 to take transmitter out of multidrop
mode
• Low Flow Cutoff set too high
• Configure Low Flow Cutoff to a lower setting or increase flow to a
value above the low flow cutoff
• PZR Activated
• Open PZR switch at terminals 5 and 6 to deactivate the PZR
• Flow is in reverse direction
• Enable Reverse Flow function
• Shorted coil
• Coil check – perform sensor test
• Empty pipe
• Fill pipe
• Electronics failure
• Verify transmitter operation with an 8714D Calibration Standard or
replace the electronics stack
• Loop resistance is greater than
600 ohms
• Reduce loop resistance to less than 600 ohms
• Perform analog loop test
• Insufficient supply voltage to
analog output
• Verify analog output supply voltage
• Perform analog loop test
• Transmitter not ranged properly
• Reset the transmitter range values –
see Upper Range Value (URV) on page 34
• Check tube size setting in transmitter and make sure it matches the
actual tube size – see Line size on page 34
• Electronics failure
• Cycle power. If alarm is still present, verify transmitter operation with
an 8714 D Calibration Standard or replace the electronics stack
• Open coil circuit
• Check coil drive circuit connections at the sensor and at the
transmitter
• Analog output diagnostic alarm
is active
• See AO diagnostic alarm on page 89
• Coil power or coil current is over
limit
• Check coil drive circuit connections at the sensor and at the
transmitter
• Cycle power. If alarm is still present, verify transmitter operation with
an 8714 D Calibration Standard or replace the electronics stack
• Connected to incompatible
sensor
• See Implementing a Universal Transmitter on page 237
Output at 20.8 mA
Output at alarm level
166
Corrective action
Troubleshooting
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
Table 9-7. Common Magmeter Issue (continued)
Symptom
Potential cause
• Wiring error
• Check pulse output wiring at terminals 3 and 4. Refer to wiring
diagram for pulse counter and pulse output. See Connect pulse
output on page 41.
• PZR activated
• Remove signal at terminals 5 and 6 to deactivate the PZR.
• No power to transmitter
• Check pulse output wiring at terminals 3 and 4. Refer to wiring
diagram for pulse counter and pulse output.
• Power the transmitter
• Reverse flow
• Enable Reverse Flow function
• Electronics failure
• Verify transmitter operation with an 8714D Calibration Standard or
replace the electronics stack
• Pulse output incorrectly
configured
• Review configuration and correct as necessary
• 4–20 mA output configuration
• Check analog power switch (internal/external). The Handheld
Communicator requires a 4–20 mA output to function.
• Communication interface wiring
problems
• Incorrect load resistance (250 Ohm minimum, 600 Ohm maximum)
Check appropriate wiring diagram
• Low batteries in the Handheld
Communicator
• Replace the batteries in the Handheld Communicator – see the
communicator manual for instructions
• Old revision of software in the
Handheld Communicator
• Consult your local sales office about updating to the latest revision
of software
• Many possible causes depending
upon the message
• See Table 9-1 on page 157, Table 9-2 on page 159, and Table 9-3 on
page 160 for the LOI or Handheld Communicator messages
• Input signal does not provide
enough counts
• Verify that the discrete input provided meets the requirements in
Section 3.4.3 Connect discrete input
• Perform a loop test to validate the analog control loop
• Perform a D/A trim. This allows the calibration of the analog output
with an external reference at operating endpoints of the analog
output.
Pulse output at zero,
regardless of flow
Communication problems
with the Handheld
Communicator
Error Messages on LOI or
Handheld Communicator
Discrete input does not
register
Troubleshooting
Corrective action
167
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
Table 9-7. Common Magmeter Issue (continued)
Symptom
Reading does not appear to
be within rated accuracy
Noisy Process
168
Potential cause
Corrective action
• Transmitter, control system, or
other receiving device not
configured properly
• Check all configuration variables for the transmitter, sensor,
communicator, and/or control system
• Check these other transmitter settings:
•Sensor calibration number
•Units
•Line size
•Perform a loop test to check the integrity of the circuit
• Electrode Coating
• Enable Coated Electrode Detection diagnostic
• Use bullet-nose electrodes
• Downsize sensor to increase flow rate above 3 ft/s
• Periodically clean sensor
• Gas/air in line
• Move the sensor to another location in the process line to ensure it is
full under all conditions
• Moisture problem
• Perform the sensor tests - see Table 9-8 on page 172
• Insufficient
upstream/downstream pipe
diameter
• Move sensor to a new location with 5 pipe diameters upstream and 2
pipe diameters downstream if possible
• Cables for multiple magmeters
run through same conduit
• Use dedicated conduit run for each sensor and transmitter
• Improper wiring
• If electrode shield and electrode signal wires are switched, flow
indication will be about half of what is expected. Check wiring
diagrams.
• Flow rate is below 1 ft/s
(specification issue)
• See accuracy specification for specific transmitter and sensor
• Auto zero was not performed
when the coil drive frequency
was changed from 5 Hz to 37 Hz
• Set the coil drive frequency to 37 Hz, verify the sensor is full, verify
there is no flow, and perform the auto zero function
• Sensor failure–shorted
electrode
• Perform the sensor tests - see Table 9-8 on page 172
• Sensor failure–shorted or open
coil
• Perform the sensor tests - see Table 9-8 on page 172
• Transmitter failure
• Verify transmitter operation with an 8714 Calibration Standard or
replace the electronics board
• Chemical additives upstream of
magnetic flowmeter
• See Troubleshooting high process noise on page 163
• Move injection point downstream of magnetic flowmeter, or move
magnetic flowmeter
• Sludge flows–mining/coal/
sand/slurries (other slurries with
hard particles)
• Decrease flow rate below 10 ft/s
• Styrofoam or other insulating
particles in process
• See Troubleshooting high process noise on page 163
• Consult factory
• Electrode coating
• Enable Coated Electrode Detection diagnostic
• Use a smaller sensor to increase flow rate above 3 ft/s
• Periodically clean sensor
• Gas/air in line
• Move the sensor to another location in the process line to ensure it is
full under all conditions
• Low conductivity fluids (below
10 microsiemens/cm)
• Trim electrode and coil wires – see Cable preparation on page 27
• Keep flow rate below 3 FPS
• Integral mount transmitter
• Use component cable - see Table 2-11 on page 25
Troubleshooting
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
Table 9-7. Common Magmeter Issue (continued)
Symptom
Potential cause
Meter output is unstable
9.6
Corrective action
• Medium to low conductivity
fluids (10–25
microsiemens/cm) combined
with cable vibration or 60 Hz
interference
• Eliminate cable vibration
• Move cable to lower vibration run
• Tie down cable mechanically
• Use an integral mount
• Trim electrode and coil wires - see Cable preparation on page 27
• Route cable line away from other equipment
powered by 60 Hz
• Use component cable - see Table 2-11 on page 25
• Electrode incompatibility
• Check the Technical Data Sheet, Magnetic Flowmeter Material
Selection Guide (document number 00816-0100-3033), for
chemical compatibility with electrode material
• Improper grounding
• Check ground wiring – see Process reference connection on page 19
for wiring and grounding procedures
• High local magnetic or electric
fields
• Move magnetic flowmeter (20–25 ft away is usually acceptable)
• Control loop improperly tuned
• Check control loop tuning
• Sticky valve (look for periodic
oscillation of meter output)
• Service valve
• Sensor failure
• Perform the sensor tests
(See Table 9-8 on page 172)
• Analog output loop problem
• Check that the 4 to 20 mA loop matches the digital value Perform
analog output test
Sensor troubleshooting
This section describes manual tests that can be performed on the sensor to verify the health of
individual components. The tests will require the use of a digital multimeter capable of
measuring conductance in nanoSiemens and an LCR meter. A sensor circuit diagram is shown in
Figure 9-1. The tests described below will check for continuity or isolation of the internal
components of the sensor.
Figure 9-1. Sensor Circuit Diagram (Simplified)
Troubleshooting
169
Section 9: Troubleshooting
9.6.1
Reference Manual
00809-0100-4444, Rev AD
August 2015
Sensor adapter
The sensor adapter is the part of the sensor that provides the internal connection feed-through
wiring from the internal sensor components to the socket module connections. The top of the
adapter has 10 pins - four pins for the coils, four pins for the electrodes, and two pins for the
process reference. Each connection point has two pins associated for redundant continuity. See
Figure 9-2.
The best location for testing the sensor components is taking measurements directly on the
feed-through pins. Direct measurement on the pins eliminates the possibility of an erroneous
measurement caused by a bad socket module or remote wiring. The figure below shows the
feed-through pin connections as they relate to the terminal connections described in the tests.
Figure 9-2. Sensor Adapter Feed-through Pins
9.6.2
Socket module
The socket module connects the sensor adapter to the transmitter. There are two versions of
the socket module—one for integral mount transmitters and one for remote mount
transmitters. Refer to Figure 9-3 and Figure 9-4. The socket module is a replaceable component.
If test measurements taken through the socket module show a failure, remove the socket
module and confirm measurements directly on the feed-through pins of the sensor adapter. To
remove the socket module, refer to Section 8: Maintenance.
170
Troubleshooting
Reference Manual
00809-0100-4444, Rev AD
Section 9: Troubleshooting
August 2015
Figure 9-3. IIntegral Mount Socket Module
Figure 9-4. Remote Mount Socket Module
Troubleshooting
171
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
9.6.3
Installed sensor tests
If a problem with an installed sensor is identified, refer to Table 9-8 on page 172 to assist in troubleshooting the sensor. Disconnect or turn off power to the transmitter before performing any
of the sensor tests. Always check the operation of test equipment before each test.
If possible, take all readings from feed-through pins in the sensor adapter. If the pins in the
sensor adapter are inaccessible, take measurements at the sensor terminal block or through
remote cabling as close to the sensor as possible. Readings taken through remote cabling that is
more than 100 feet (30 meters) in length may provide incorrect or inconclusive information and
should be avoided.
The expected values in the test below assume the measurements have been taken directly at
the pins.
Table 9-8. Sensor Tests and Expected Values
Test
A. Sensor coil
Sensor
location
Installed or
uninstalled
Required
Measuring at
equipment connections Expected value
Multimeter
1 and 2 = R
Potential cause
Corrective action
2Ω ≤ R ≤ 18Ω
• Open or shorted
coil
• Remove and
replace sensor
′ < 0.3Ω
• Moisture in
terminal block
• Leaky electrode
• Process behind
liner
• Clean terminal
block
• Remove sensor
• Process behind
liner
• Leaky electrode
• Moisture in
terminal block
• Remove sensor
and dry
• Clean terminal
block
• Confirm with
sensor coil test
R 1 – R 2 ≤ 300Ω
• Unstable R1 or R2
values confirm
coated electrode
• Shorted
electrode
• Electrode not in
contact with
process
• Empty pipe
• Low conductivity
• Leaky electrode
• Process
reference
ground not
connected
properly
• Remove coating
from sensor wall
• Use bullet-nose
electrodes
• Repeat
measurement
• Remove sensor
and complete
tests in Table 9-9
• Connect process
reference ground
per 2.11 Process
reference
connection
Should be stable and same
relative magnitude of R1 and
R2 from Test D
• See Test D above
• See Test D above
17 and 3
B. Shields to
case
Installed or
uninstalled
Multimeter
3 and case
ground
17 and case
ground
C. Coil to coil
shield
Installed or
uninstalled
1 and 3
Multimeter
2 and 3
D. Electrode to
electrode
shield
Installed
LCR (Set to
Resistance
and 120 Hz)
E. Electrode to
Electrode
Installed
LCR (set to
resistance
and 120 Hz)
18 and 17 = R1
19 and 17 = R2
18 and 19
∞Ω (< 1nS)
∞Ω (< 1nS)
R1 and R2 should be stable
To test the sensor, a multimeter capable of measuring conductance in nanoSiemens is
preferred. Conductance is the reciprocal of resistance.
Or:
172
Troubleshooting
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
9.6.4
August 2015
Uninstalled sensor tests
Sensor troubleshooting can also be performed on an uninstalled sensor. If test results from
installed sensor tests are inconclusive, the next step is remove the sensor and perform the tests
outlined in Table 9-9. Take measurements from the feed-through pins and directly on the
electrode head inside the sensor. The measurement electrodes, 18 and 19, are on opposite
sides in the inside diameter of the sensor. If applicable, the third process reference electrode is
between the two measurement electrodes.
The expected values in the test below assume the measurements have been taken directly at
the pins.
Table 9-9. Uninstalled Sensor Tests and Expected Values
Sensor
location
Required
Measuring at
equipment connections
A. Terminal to
front
electrode
Uninstalled
Multimeter
18 and electrode 18(1)
≤1Ω
• Shorted electrode
• Open electrode
• Coated electrode
• Replace sensor
• Remove coating
from sensor wall
B. Terminal to
back electrode
Uninstalled
Multimeter
19 and electrode 19(1)
≤1Ω
• Shorted electrode
• Open electrode
• Coated electrode
• Replace sensor
• Remove coating
from sensor wall
C. Terminal to
reference
electrode
Uninstalled
Multimeter
17 and process
reference electrode(2)
≤ 0.3 Ω
• Shorted electrode
• Open electrode
• Coated electrode
• Replace sensor
• Remove coating
from sensor wall
≤ 0.3 Ω
• Moisture in
terminal block
• Leaky electrode
• Process behind
liner
• Clean terminal
block
• Replace terminal
block
• Replace sensor
• Shorted electrode
• Leaky electrode
• Moisture in
terminal block
• Replace sensor
• Clean terminal
block
• Replace terminal
block
• Shorted electrode
• Leaky electrode
• Moisture in
terminal block
• Replace sensor
• Clean terminal
block
• Replace terminal
block
• Process in coil
housing
• Moisture in
terminal block
• Replace sensor
• Clean terminal
block
• Replace terminal
block
Test
D. Terminal to
case ground
Uninstalled
Multimeter
17 and safety ground
18 and 17
E. Electrode to
electrode
shield
Uninstalled
Uninstalled
∞Ω
(<1 nS)
Multimeter
19 and 17
F. Electrode
shield to coil
Expected
value
Multimeter
17 and 1
∞Ω
∞Ω
(<1 nS)
(<1 nS)
Potential cause
Corrective action
1. When the connection head is in the vertical upright position and the flow arrow (see Figure 2-4 on page 10) on the connection head flange points to the
right, the front of the meter will be facing towards you. Electrode 18 is on the front of the meter. If you cannot determine the front of the meter, measure
both electrodes. One electrode should result in an open reading, while the other electrode should be less than 0.3 ohm.
2. Only valid if the sensor has a process reference electrode.
Troubleshooting
173
Reference Manual
Section 9: Troubleshooting
00809-0100-4444, Rev AD
August 2015
9.7
Technical support
Email addresses:
Worldwide: [email protected]
Asia-Pacific: [email protected]
Middle East and Africa: [email protected]
North and South America
Europe and Middle East
Asia Pacific
United States
800-522-6277
U.K.
0870 240 1978
Australia
800 158 727
Canada
+1 303-527-5200
The Netherlands
+31 (0) 318 495 555
New Zealand
099 128 804
Mexico
+41 (0) 41 7686 111
France
0800 917 901
India
800 440 1468
Argentina
+54 11 4837 7000
Germany
0800 182 5347
Pakistan
888 550 2682
Brazil
+55 15 3238 3677
Italy
8008 77334
China
+86 21 2892 9000
Venezuela
+58 26 1731 3446
Central & Eastern
+41 (0) 41 7686 111
Japan
+81 3 5769 6803
Russia/CIS
+7 495 981 9811
South Korea
+82 2 3438 4600
Egypt
0800 000 0015
Singapore
+65 6 777 8211
Oman
800 70101
Thailand
001 800 441 6426
Qatar
431 0044
Malaysia
800 814 008
Kuwait
663 299 01
South Africa
800 991 390
Saudi Arabia
800 844 9564
UAE
800 0444 0684
174
Troubleshooting
Reference Manual
00809-0100-4444, Rev AD
9.8
Section 9: Troubleshooting
August 2015
Service
To expedite the return process outside the United States, contact the nearest Rosemount representative.
Within the United States and Canada, call the North American Response Center using the
800-654-RSMT (7768) toll-free number. The Response Center, available 24 hours a day, will
assist you with any needed information or materials.
The center will ask for product, model, and serial numbers and will provide a Return Material
Authorization (RMA) number. The center will also ask for the name of the process material to
which the product was last exposed.
Mishandling products exposed to a hazardous substance may result in death or serious injury. If
the product being returned was exposed to a hazardous substance as defined by OSHA, a copy
of the required Material Safety Data Sheet (MSDS) for each hazardous substance identified must
be included with the returned goods.
The North American Response Center will detail the additional information and procedures
necessary to return goods exposed to hazardous substances.
Troubleshooting
175
Section 9: Troubleshooting
August 2015
176
Reference Manual
00809-0100-4444, Rev AD
Troubleshooting
Appendix A: Specifications and Reference Data
Reference Manual
August 2015
00809-0100-4444, Rev AD
Appendix A
Specifications and Reference
Data
Rosemount 8732EM Transmitter specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rosemount 8705-M Flanged Sensor specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rosemount 8711-M/L Wafer Sensor specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rosemount 8721 Hygienic (Sanitary) Sensor specifications . . . . . . . . . . . . . . . . . . . . . . .
page 177
page 188
page 194
page 198
A.1
Rosemount 8732EM Transmitter specifications
A.1.1
Functional specifications
Sensor compatibility
Compatible with Rosemount 8705, 8711, and 8721 sensors. Compatible with AC and DC
powered sensors of other manufacturers.
Transmitter coil drive current
500mA
Flow rate range
Capable of processing signals from fluids that are traveling between 0.04 and 39 ft/s (0.01 to 12
m/s) for both forward and reverse flow in all sensor sizes. Full scale continuously adjustable
between –39 and 39 ft/s (–12 to 12 m/s).
Conductivity limits
Process liquid must have a conductivity of 5 microSiemens/cm (5 micromhos/cm) or greater.
Power supply
90 - 250VAC, 50/60Hz or 12 - 42VDC
Specifications and Reference Data
177
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Line power fuses
90-250VAC systems
1A, 250V, I2t ≥ 1.5 A2s Rating, Fast Acting
Bussman AGC-1, Littelfuse 31201.5HXP
12-42VDC systems
3 Amp, 250V, I2t ≥ 14 A2s Rating, Fast Acting
Bel Fuse 3AG 3-R, Littelfuse 312003P, Schurter 0034.5135
Power consumption
15W maximum - DC
40VA maximum - AC
Switch-on current
AC: Maximum 35.7A (< 5ms) at 250VAC
DC: Maximum 42A (< 5ms) at 42VDC
AC power supply requirements
Units powered by 90 - 250VAC have the following power requirements.
Figure A-1. AC Current Requirements
178
Specifications and Reference Data
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Figure A-2. Apparent Power
DC supply current requirements
Units powered by 12VDC power supply may draw up to 1.2A of current steady state.
Figure A-3. DC Current Requirements
Ambient temperature limits
Operating
–40 to 140 °F (–40 to 60 °C) without local operator interface
–4 to 140 °F (–20 to 60 °C) with local operator interface
The Local Operator Interface (LOI) will not display at temperatures below -20°C
Specifications and Reference Data
179
Appendix A: Specifications and Reference Data
Reference Manual
00809-0100-4444, Rev AD
August 2015
Storage
–40 to 185 °F (–40 to 85 °C) without local operator interface
–22 to 176 °F (–30 to 80 °C) with local operator interface(1)
Humidity limits
0–95% RH to 140 °F (60 °C)
Altitude
2000 meters maximum
Enclosure rating
Type 4X, IEC 60529, IP66 (transmitter)
Transient protection rating
Built in transient protection that conforms to:
IEC 61000-4-4 for burst currents
IEC 61000-4-5 for surge currents.
IEC 611185-2.2000, Class 3 up to 2kV and up to 2kA protection.
Turn-on time
Five minutes to rated accuracy from power up
Five seconds from power interruption
Start-up time
50ms from zero flow
Low flow cut-off
Adjustable between 0.01 and 38.37 ft/s (0.003 and 11.7 m/s). Below selected value, output is
driven to the zero flow rate signal level.
Overrange capability
Signal output will remain linear until 110% of upper range value or 44 ft/s (13 m/s). The signal
output will remain constant above these values. Out of range message displayed on LOI and the
Field Communicator.
Damping
Adjustable between 0 and 256 seconds
180
Specifications and Reference Data
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
A.1.2
August 2015
Advanced diagnostics capabilities
Basic
Self test
Transmitter faults
Analog output test
Pulse output test
Tunable empty pipe
Reverse flow
Coil circuit fault
Electronics temperature
Process diagnostics (DA1)
Ground/wiring fault
High process noise
Electrode coating diagnostic
Smart meter verification (DA2)
SMART™Meter Verification (continuous or on-demand)
4-20mA loop verification
A.1.3
Output signals
Analog output adjustment(1)
4–20mA, switch-selectable as internally or externally powered.
Analog loop load limitations
Internally powered 24VDC max, 500 ohms max loop resistance
Externally powered 10.8 - 30VDC max.
Loop resistance is determined by the voltage level of the external power supply at the
transmitter terminals.
(1)
For transmitters with intrinsically safe outputs (option code B), power must be supplied externally.
Specifications and Reference Data
181
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Figure A-4. Analog Loop Load Limitations
Load (Ohms)
600
Operating
Region
0
10.8
30
Power Supply (Volts)
Rmax =
Vps =
Rmax =
31.25 (Vps – 10.8)
Power Supply Voltage (Volts)
Maximum Loop Resistance (Ohms)
The analog output is automatically scaled to provide 4mA at lower range value and 20mA at
upper range value. Full scale continuously adjustable between -39 and 39 ft/s (-12 to 12 m/sec),
1 ft/s (0.3 m/s) minimum span.
HART Communications is a digital flow signal. The digital signal is superimposed on the 4–
20mA signal and is available for the control system interface. A minimum of 250 Ohms loop
resistance is required for HART communications.
Scalable pulse frequency adjustment(1)(2)
0-10,000Hz, switch-selectable as internally or externally powered. Pulse value can be set to
equal desired volume in selected engineering units. Pulse width adjustable from 0.1 to 650 ms.
Internally powered: Outputs up to 12VDC
Externally powered: Input 5 - 28VDC
Output testing
Analog output test(3)
Transmitter may be commanded to supply a specified current between 3.5 and 23mA.
Pulse output test(4)
Transmitter may be commanded to supply a specified frequency between 1 and 10,000Hz.
Optional discrete output function (AX option)
Externally powered at 5 - 28VDC, 240mA max, solid state switch closure to indicate either:
Reverse flow
Activates switch closure output when reverse flow is detected.
(1)
(2)
(3)
(4)
182
For transmitters with intrinsically safe outputs (option code B), power must be supplied externally.
For transmitters with intrinsically safe outputs (option code B), frequency range is limited to 0-5000Hz.
For transmitters with intrinsically safe outputs (option code B), power must be supplied externally.
For transmitters with intrinsically safe outputs (option code B), power must be supplied externally.
Specifications and Reference Data
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Zero flow
Activates switch closure output when flow goes to 0 ft/s or below low flow cutoff.
Empty pipe
Activates switch closure output when an empty pipe condition is detected.
Transmitter faults
Activates switch closure output when a transmitter fault is detected.
Flow limit 1, Flow limit 2
Activates switch closure output when the transmitter measures a flow rate that meets the
conditions established for this alert. There are two independent flow limit alerts that can be
configured as discrete outputs.
Totalizer limit
Activates switch closure output when the transmitter measures a total flow that meets the
conditions established for this alert.
Diagnostic status
Activates switch closure output when the transmitter detects a condition that meets the
configured criteria of this output.
Optional discrete input function (AX option)
Externally powered at 5 - 28VDC, 1.4 - 20mA to activate switch closure to indicate either:
Net total reset
Resets the net totalizer value to zero.
Positive zero return (PZR)
Forces outputs of the transmitter to zero flow.
Security lockout
Security lockout switch on the electronics board can be set to deactivate all LOI and HART-based
communicator functions to protect configuration variables from unwanted or accidental
change.
LOI lockout
The display can be manually locked to prevent unintentional configuration changes. The display
lock can be activated through a HART® communication device, or by holding the UP arrow for 3
seconds and then following the on-screen instructions. When the display lock is activated, a lock
symbol will appear in the lower right hand corner of the display. To deactivate the display lock,
hold the UP arrow for 3 seconds and follow the on-screen instructions.
Specifications and Reference Data
183
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Display auto lock can be configured from the LOI with the following settings: OFF, 1 Minute, or
10 Minutes
A.1.4
Sensor compensation
Rosemount sensors are calibrated in a flow lab at the factory and are assigned a calibration
number. The calibration number must be entered into the transmitter, enabling interchangeability of sensors without calculations or a compromise in standard accuracy.
8732EM transmitters and other manufacturers’ sensors can be calibrated at known process
conditions or at the Rosemount NIST-Traceable Flow Facility. Transmitters calibrated on site
require a two-step procedure to match a known flow rate. This procedure can be found in the
operations manual.
A.1.5
Performance specifications
System specifications are given using the frequency output and with the unit at reference
conditions.
Accuracy
Includes the combined effects of linearity, hysteresis, and repeatability.
Rosemount 8705-M Sensor
Standard system accuracy is ±0.25% of rate ±1.0 mm/sec from 0.04 to 6 ft/s (0.01 to 2 m/s);
above 6 ft/s (2 m/s), the system has an accuracy of ±0.25% of rate ±1.5 mm/sec.
Optional high accuracy is ±0.15% of rate ±1.0 mm/sec from 0.04 to 13 ft/s (0.01 to 4 m/s);
above 13 ft/s (4 m/s), the system has an accuracy of ±0.18% of rate.(1)
2.5
% of Rate
2.0
1.5
1.0
0.25%
0.15%
0.5
0
0
3
(1)
6
(2)
13
(4)
20
(6)
27
(8)
33
(10)
40
(12)
Velocity in ft/s (m/s)
(1)
184
For sensor sizes greater than 12 in. (300 mm) the high accuracy is ±0.25% of rate from 3 to 39 ft/sec (1 to 12 m/sec).
Specifications and Reference Data
Appendix A: Specifications and Reference Data
Reference Manual
August 2015
00809-0100-4444, Rev AD
Rosemount 8711-M/L Sensor
Standard system accuracy is ±0.25% of rate ±2.0 mm/sec from 0.04 to 39 ft/s (0.01 to 12 m/s).
Optional high accuracy is ±0.15% of rate ±1.0 mm/sec from 0.04 to 13 ft/s (0.01 to 4 m/s);
above 13 ft/s (4 m/s), the system has an accuracy of ±0.18% of rate.
2.5
% of Rate
2.0
1.5
1.0
0.25%
0.15%
0.5
0
0
3
(1)
6
(2)
20
(6)
13
(4)
27
(8)
33
(10)
40
(12)
Velocity in ft/s (m/s)
Rosemount 8721 Sensor
Standard system accuracy is ±0.5% of rate from 1 to 39 ft/s (0.3 to 12 m/s); between 0.04 and
1.0 ft/s (0.01 and 0.3 m/s), the system has an accuracy of ±0.005 ft/s (0.0015 m/s).
Optional high accuracy is ±0.25% of rate from 3 to 39 ft/s (1 to 12 m/s).
2.5
% of Rate
2.0
1.5
1.0
0.25%
0.5%
0.5
0
0
3
(1)
6
(2)
20
(6)
13
(4)
27
(8)
33
(10)
40
(12)
Velocity in ft/s (m/s)
Other manufacturers’ sensors
When calibrated in the Rosemount Flow Facility, system accuracies as good as 0.5% of rate can
be attained.
There is no accuracy specification for other manufacturers’ sensors calibrated in the process
line.
Specifications and Reference Data
185
Appendix A: Specifications and Reference Data
A.1.6
Reference Manual
00809-0100-4444, Rev AD
August 2015
Analog output effects
Analog output has the same accuracy as frequency output plus an additional ±4μA at room
temperature.
Repeatability
±0.1% of reading
Response time (analog output)
20 ms max response time to step change in input
Stability
±0.1% of rate over six months
Ambient temperature effect
±0.25% change over operating temperature range
A.1.7
Physical specifications
Materials of construction
Standard housing
Low copper aluminum
Type 4X and IEC 60529 IP66
Paint
Polyurethane coat (1.3 to 5 mils thick)
Optional housing
316/316L unpainted, option code SH
Type 4X and IEC 60529 IP66
Cover gasket
Buna-N
Electrical connections
Conduit entries: 1/2-in. NPT or M20.
Terminal block screws: 6-32 (No. 6) suitable for up to 14 AWG wire.
Safety grounding screws: external stainless assembly, M5; internal 8-32 (No. 8)
186
Specifications and Reference Data
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Vibration rating
3G per IEC 61298
Dimensions
See Product Data Sheet.
Weight
Aluminum - approximately 7 lbs. (3.2 kg).
316 stainless steel - approximately 23 lbs. (10.5 kg).
Add 1 pound (0.5 kg) for display option code M4 or M5.
A.1.8
F0875 Low Power Software Option
Available with DC power supply (2) and intrinsically safe outputs (B) only. This software option
lowers the coil drive current from 500mA to 75mA in order to conserve power for applications
where battery packs or solar panels are the primary power source. The coils are still driven in a
continuous manner, optimizing measurement performance. Power consumption of the
transmitter is reduced to approximately 2W. Use of the analog output results in a maximum of
1W of additional power consumption under a high alarm condition (23.5mA) and 24VDC
supply. Power consumption of the output loop can be minimized by utilizing the pulse output or
pulling information off of the HART signal. Both the pulse loop and the analog loop require
external power source to be applied. Flow performance reference accuracy is 1.0% of rate.
To ensure the sensor is calibrated with a low power calibration number, Option Code D3 has
been established. This code must appear in the transmitter and sensor model number. Sample
model numbers for lower power are:
8732EMT2B1N5M4DA1DA2D3F0875
8705THA020C7M0N5B3D3
Specifications and Reference Data
187
Appendix A: Specifications and Reference Data
Reference Manual
00809-0100-4444, Rev AD
August 2015
A.2
Rosemount 8705-M Flanged Sensor specifications
A.2.1
Functional specifications
Service
Conductive liquids and slurries
Line sizes
/2–in. to 36-in. (15 mm to 900 mm) for Rosemount 8705
1
Sensor coil resistance
7 - 16 Ω
Interchangeability
Rosemount 8705-M sensors are interchangeable with 8732EM transmitters. System accuracy is
maintained regardless of line size or optional features. Each sensor nameplate has a 16-digit
calibration number that can be entered into a transmitter through the Local Operator Interface
(LOI) or the Field Communicator.
Upper range limit
39.37 ft/s (12 m/s)
Process temperature limits
PTFE lining
–20 to 350 °F (–29 to 177 °C)
ETFE lining
–20 to 300 °F (–29 to 149 °C)
PFA lining
-20 to 350 °F (-29 to 177 °C)
188
Specifications and Reference Data
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Polyurethane lining
0 to 140 °F (–18 to 60 °C)
Neoprene lining
0 to 176 °F (–18 to 80 °C)
Linatex lining
0 to 158 °F (–18 to 70 °C)
Adiprene lining
0 to 200 °F (–18 to 93 °C)
Ambient temperature limits
–20 to 140 °F (–29 to 60 °C)
Pressure limits
See Table A-1, Table A-2 and Table A-3
Vacuum limits
PTFE lining
Full vacuum to 350 °F (177 °C) through 4-in. (100 mm) line sizes. Consult factory for vacuum
applications with line sizes of 6 in. (150 mm) or larger.
All other standard sensor lining materials
Full vacuum to maximum material temperature limits for all available line sizes.
Submergence protection (IP68)
The remote mount 8705-M sensor is rated IP68 for submergence to a depth of 33 ft. (10 m) for a
period of 48 hours. IP68 rating requires the transmitter must be remote mount. Installer must
use IP68 approved cable glands, conduit connections, and/or conduit plugs. For more details on
proper installation techniques for IP68 submersible application, reference Rosemount Technical
Note 00840-0100-4750 available on www.rosemount.com.
Conductivity limits
Process liquid must have a minimum conductivity of 5 microSiemens/cm (5 micromhos/cm) or
greater.
Specifications and Reference Data
189
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Table A-1. Temperature vs. Pressure Limits(1)
Sensor temperature vs. pressure limits for ASME B16.5 class flanges (1/2-in. to 36-in. line
sizes)(2)
Pressure
Flange material
Flange rating
@ -20 to 100 °F
(-29 to 38 °C)
@ 200 °F
(93 °C)
@ 300 °F
(149 °C)
@ 350 °F
(177 °C)
Class 150
285 psi
260 psi
230 psi
215 psi
Class 300
740 psi
675 psi
655 psi
645 psi
(3)
1000 psi
800 psi
700 psi
650 psi
(4)
1480 psi
1350 psi
1315 psi
1292 psi
Class 900
2220 psi
2025 psi
1970 psi
1935 psi
Class 1500
3705 psi
3375 psi
3280 psi
3225 psi
Class 2500
6170 psi
5625 psi
5470 psi
5375 psi
Class 150
275 psi
235 psi
205 psi
190 psi
Class 300
Class 600
Carbon Steel
304 Stainless
Steel
1.
2.
3.
4.
5.
6.
Class 600
720 psi
600 psi
530 psi
500 psi
Class 600
(5)
1000 psi
800 psi
700 psi
650 psi
Class 600
(6)
1440 psi
1200 psi
1055 psi
997 psi
Class 900
2160 psi
1800 psi
1585 psi
1497 psi
Class 1500
3600 psi
3000 psi
2640 psi
2495 psi
Class 2500
6000 psi
5000 psi
4400 psi
4160 psi
Liner temperature limits must also be considered.
30-in. and 36-in. AWWA C207 Class D rated to 150 psi at atmospheric temperature.
Option Code C6.
Option Code C7.
Option Code S6.
Option Code S7.
Table A-2. Temperature vs. Pressure Limits(1)
Sensor temperature vs. pressure limits for AS2129 Table D and E flanges (4-in. to 24-in. line sizes)
Pressure
Flange material
Flange rating
@ -29 to 50 °C
(-20 to 122 °F)
@ 100 °C
(212 °F)
@ 150 °C
(302 °F)
@ 200 °C
(392 °F)
Carbon Steel
D
E
101.6 psi
203.1 psi
101.6 psi
203.1 psi
101.6 psi
203.1 psi
94.3 psi
188.6 psi
1.
Liner temperature limits must also be considered.
Table A-3. Temperature vs. Pressure Limits(1)
Sensor temperature vs. pressure limits for EN 1092-1 flanges (15 mm to 600 mm line sizes)
Pressure
190
Flange material
Flange rating
@ -29 to 50 °C
(-20 to 122 °F)
@ 100 °C
(212 °F)
@ 150°C
(302 °F)
@ 175°C
(347 °F)
Carbon Steel
PN 10
PN 16
PN 25
PN 40
10 bar
16 bar
25 bar
40 bar
10 bar
16 bar
25 bar
40 bar
9.7 bar
15.6 bar
24.4 bar
39.1 bar
9.5 bar
15.3 bar
24.0 bar
38.5 bar
Specifications and Reference Data
Appendix A: Specifications and Reference Data
Reference Manual
August 2015
00809-0100-4444, Rev AD
Table A-3. Temperature vs. Pressure Limits(1) (continued)
Sensor temperature vs. pressure limits for EN 1092-1 flanges (15 mm to 600 mm line sizes)
Pressure
1.
A.2.2
Flange material
Flange rating
@ -29 to 50 °C
(-20 to 122 °F)
@ 100 °C
(212 °F)
@ 150°C
(302 °F)
@ 175°C
(347 °F)
304 Stainless Steel
PN 10
PN 16
PN 25
PN 40
9.1 bar
14.7 bar
23 bar
36.8 bar
7.5 bar
12.1 bar
18.9 bar
30.3 bar
6.8 bar
11.0 bar
17.2 bar
27.5 bar
6.5 bar
10.6 bar
16.6 bar
26.5 bar
Liner temperature limits must also be considered.
Physical specifications
Non-wetted materials
Sensor pipe
Type 304/304L SST or Type 316/316L SST
Flanges
Carbon steel, Type 304/304L SST, or Type 316/316L SST
Coil housing
Rolled carbon steel
Paint
Polyurethane coat (1.3 to 5 mils thick)
Optional coil housing
316/316L unpainted, option code SH
Process wetted materials
Lining
PTFE, ETFE, PFA, Polyurethane, Neoprene, Linatex, Adiprene, PFA+
Electrodes
316L SST, Nickel Alloy 276 (UNS N10276), Tantalum, 80% Platinum-20% Iridium, Titanium
Flat-faced flanges
Flat-faced flanges are manufactured with full-face liners. Available in Neoprene and Linatex only.
Specifications and Reference Data
191
Appendix A: Specifications and Reference Data
Reference Manual
00809-0100-4444, Rev AD
August 2015
Process connections
ASME B16.5
/2-in. to 24-in. (Class 150, 300, 600(1))
1
1-in. to 12-in. (Class 900)(2)
11/2-in. to 12-in. (Class 1500)(2)
11/2-in. to 6-in. (Class 2500)(2)
ASME B16.47
30-in. to 36-in. (Class 150)
30-in. to 36-in. (Class 300)
AWWA C207 Class D
30-in. and 36-in.
MSS SP44
30-in. to 36-in. (Class 150)
EN 1092-1
200 mm to 900 mm (8-in. to 36-in.) PN10
100 mm to 900 mm (4 -in. to 36-in.) PN16
200 mm to 900 mm (8-in. to 36-in.) PN 25
15 mm to 900 mm (1/2-in. to 36-in.) PN40
AS2129
15 mm to 900 mm (1/2-in. to 36-in.) Table D and E
AS4087
50 mm to 600 mm (2-in. to 24-in.) PN16, PN21, PN35
JIS B2220
15 mm to 200 mm (1/2-in. to 8-in.) 10K, 20K, 40K
(1)
(2)
192
For PTFE and ETFE, maximum working pressure is derated to 1000 psig.
For Class 900 and higher flange ratings, liner selection is limited to resilient liners.
Specifications and Reference Data
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Electrical connections
Conduit entries: 1/2 in. NPT or M20.
Terminal block screws: 6-32 (No. 6) suitable for up to 14 AWG wire.
Safety grounding screws: external stainless assembly, M5; internal 8-32 (No. 8)
Process reference electrode (optional)
A process reference electrode can be installed similarly to the measurement electrodes through
the sensor lining on 8705 sensors. It will be made of the same material as the measurement
electrodes.
Grounding rings (optional)
Grounding rings can be installed between the flange and the sensor face on both ends of the
sensor. Single ground rings can be installed on either end of the sensor. They have an I.D. slightly
larger than the sensor I.D. and an external tab to attach ground wiring. Grounding rings are
available in 316L SST, Nickel Alloy 276 (UNS N10276), Titanium, and Tantalum. See Product
Data Sheet.
Lining protectors (optional)
Lining protectors can be installed between the flange and the sensor face on both ends of the
sensor. The leading edge of lining material is protected by the lining protector; lining protectors
cannot be removed once they are installed. Lining protectors are available in 316L SST, Nickel
Alloy 276 (UNS N10276), and Titanium. See Product Data Sheet.
Dimensions
See the Product Data Sheet.
Weight
See the Product Data Sheet.
Specifications and Reference Data
193
Appendix A: Specifications and Reference Data
Reference Manual
00809-0100-4444, Rev AD
August 2015
A.3
Rosemount 8711-M/L Wafer Sensor specifications
A.3.1
Functional specifications
Service
Conductive liquids and slurries
Line sizes
1.5-in. to 8-in. (4 mm to 200 mm)
Sensor coil resistance
10 - 18 Ω
Interchangeability
Rosemount 8711-M/L sensors are interchangeable with 8732EM transmitter. System accuracy is
maintained regardless of line size or optional features. Each sensor nameplate has a sixteen-digit
calibration number that can be entered into a transmitter through the Local Operator Interface
(LOI) or the Field Communicator.
Upper range limit
39.37 ft/s (12 m/s)
Process temperature limits
ETFE lining
-20 to 300 °F (–29 to 149 °C)
PTFE lining
-20 to 350 °F (-29 to 177 °C)
PFA Lining
-20 to 200 °F (-29 to 93 °C)
194
Specifications and Reference Data
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Ambient temperature limits
–20 to 140 °F (–29 to 60 °C)
Maximum safe working pressure at 100 °F (38 °C)
ETFE lining
Full vacuum to 740 psi (5.1 MPa)
PTFE lining
Full vacuum through 4-in. (100 mm) line sizes. Consult factory for vacuum applications with line
sizes of 6-in. (1450 mm) or larger.
PFA lining
Full vacuum to 285 psi (1.96 MPa)
Submergence protection (IP68)
The remote mount 8711-M/L sensor is rated IP68 for submergence to a depth of 33 ft. (10 m) for
a period of 48 hours. IP68 rating requires the transmitter must be remote mount. Installer must
use IP68 approved cable glands, conduit connections, and/or conduit plugs. For more details on
proper installation techniques for IP68 submersible application, reference Rosemount Technical
Note 00840-0100-4750 available on www.rosemount.com.
Conductivity limits
Process liquid must have a minimum conductivity of 5 microSiemens/cm (5 micromhos/cm) or
greater for 8711.
A.3.2
Physical specifications
Non-wetted materials
Sensor body
303 SST
CF3M or CF8M
Type 304/304L
Coil housing
Rolled carbon steel
Paint
Polyurethane coat (1.3 to 5 mils thick)
Specifications and Reference Data
195
Appendix A: Specifications and Reference Data
Reference Manual
00809-0100-4444, Rev AD
August 2015
Process-wetted materials
Lining
ETFE, PTFE
Electrodes
316L SST, Nickel Alloy 276 (UNS N10276), Tantalum, 80% Platinum—20% Iridium, Titanium
Process connections
Mounts between these flange configurations
ASME B16.5: Class 150, 300
EN 1092-1: PN10, PN16, PN25, PN40
JIS B2220: 10K, 20K,
AS4087: PN16, PN21, PN35
Studs, nuts, and washers
MK2–Carbon Steel
ASME B16.5
Studs, full thread: CS, ASTM A193, Grade B7
Hex nuts: ASTM A194 Grade 2H;
Flat washers: CS, Type A, Series N, SAE per ANSI B18.2.1
All items clear, chromate zinc-plated
EN 1092-1
Studs, full thread: CS, ASTM A193, Grade B7
Hex nuts: ASTM A194 Grade 2H; DIN 934 H = D
Flat washers: CS, DIN 125
All items yellow zinc-plated
196
Specifications and Reference Data
Appendix A: Specifications and Reference Data
Reference Manual
August 2015
00809-0100-4444, Rev AD
MK3–316 SST
ASME B16.5
Studs, full thread: ASTM A193, Grade B8M Class 1
Hex nuts: ASTM A194 Grade 8M;
Flat washers: 316 SST, Type A, Series N, SAE per ANSI B18.2.1
EN 1092-1
Studs, full thread: ASTM A193, Grade B8M Class 1
Hex nuts: ASTM A194 Grade 8M; DIN 934 H = D
Flat washers: 316 SST, DIN 125
Electrical connections
Conduit entries: 1/2 in. NPT or M20 standard
Terminal block screws: 6-32 (No. 6) suitable for up to 14 AWG wire
Safety grounding screws: external stainless assembly, M5; internal 8-32 (No. 8)
Process reference electrode (optional)
A process reference electrode can be installed similarly to the measurement electrodes through
the sensor lining. It will be made of the same material as the measurement electrodes.
Grounding rings (optional)
Grounding rings can be installed between the flange and the sensor face on both ends of the
sensor. They have an I.D. slightly smaller than the sensor I.D. and an external tab to attach
ground wiring. Grounding rings are available in 316L SST, Nickel Alloy 276 (UNS N10276),
titanium, and tantalum. See Product Data Sheet.
Dimensions
See the Product Data Sheet.
Weight
See the Product Data Sheet.
Specifications and Reference Data
197
Appendix A: Specifications and Reference Data
Reference Manual
00809-0100-4444, Rev AD
August 2015
A.4
Rosemount 8721 Hygienic (Sanitary) Sensor
specifications
A.4.1
Functional specifications
Service
Conductive liquids and slurries
Line sizes
/2-in. to 4-in. (15 mm to100 mm)
1
Sensor coil resistance
5 -10Ω
Interchangeability
The Rosemount 8721 sensors are interchangeable with Rosemount 8732EM transmitters.
System accuracy is maintained regardless of line size or optional features.
Each sensor label has a 16 digit calibration number that can be entered into the transmitter
through the Local Operator Interface (LOI) or the Field Communicator.
Conductivity limits
Process liquid must have a minimum conductivity of 5 microSiemens/cm (5 micromhos/cm) or
greater. Excludes the effect of interconnecting cable length in remote mount transmitter
installations.
Flow rate range
Capable of processing signals from fluids that are traveling between 0.04 and 39 ft/s (0.01 to 12
m/s) for both forward and reverse flow in all sensor sizes. Full scale continuously adjustable
between –39 and 39 ft/s (–12 to 12 m/s).
198
Specifications and Reference Data
Appendix A: Specifications and Reference Data
Reference Manual
August 2015
00809-0100-4444, Rev AD
Sensor ambient temperature limits
14 to 140 °F (–15 to 60 °C)
Process temperature limits
PFA lining
-20 to 350 °F (-29 to 177 °C)
Table A-4. Pressure limits
Line size
in. (mm)
1
/2 (15)
1 (25)
11/2 (40)
2 (50)
21/2 (65)
3 (80)
4 (100)
Max working
pressure
CE Mark max. working
pressure
300 psi (20.7 bar)
300 psi (20.7 bar)
300 psi (20.7 bar)
300 psi (20.7 bar)
300 psi (20.7 bar)
300 psi (20.7 bar)
210 psi (14.5 bar)
300 psi (20.7 bar)
300 psi (20.7 bar)
300 psi (20.7 bar)
300 psi (20.7 bar)
240 psi (16.5 bar)
198 psi (13.7 bar)
148 psi (10.2 bar)
Vacuum limits
Full vacuum at maximum lining material temperature; consult factory.
Submergence protection (IP68)
The remote mount 8721 sensor is rated IP68 for submergence to a depth of 33 ft. (10 m) for a
period of 48 hours. IP68 rating requires the transmitter must be remote mount. Installer must
use IP68 approved cable glands, conduit connections, and/or conduit plugs. For more details on
proper installation techniques for IP68 submersible application, reference Rosemount Technical
Note 00840-0100-4750 available on www.rosemount.com.
A.4.2
Physical specifications
Mounting
Integrally mounted transmitters are factory-wired and do not require interconnecting cables.
The transmitter can rotate in 90° increments. Remote mounted transmitters require only a
single conduit connection to the sensor.
Non-wetted materials
Sensor
304 Stainless Steel (wrapper), 304 Stainless Steel (pipe)
Terminal junction box
Low copper aluminum
Optional: 304 Stainless Steel
Specifications and Reference Data
199
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
Weight
Table A-5. 8721 Sensor weight
Line size
in. (mm)
1
Sensor only
008721-0350 Tri
Clamp fitting (each)
/2 (15)
4.84 lbs (2.20 kg)
0.58 lbs (0.263 kg)
1 (25)
4.52 lbs (2.05 kg)
0.68 lbs (0.309 kg)
1
1 /2 (40)
5.52 lbs (2.51 kg)
0.88 lbs (0.400 kg)
2 (50)
6.78 lbs (3.08 kg)
1.30 lbs (0.591 kg)
21/2 (65)
8.79 lbs (4.00 kg)
1.66 lbs (0.727 kg)
3 (80)
13.26 lbs (6.03 kg)
2.22 lbs (1.01 kg)
4 (100)
21.04 lbs (9.56 kg)
3.28 lbs (1.49 kg)
Aluminum remote junction box
Approximately 1 lb. (0.45 kg)
Paint - Polyurethane (1.3 to 5 mils)
SST remote junction box
Approximately 2.5 lbs. (1.13 kg)
Unpainted
Process wetted materials (sensor)
Liner
PFA with Ra < 32μ in. (0.81 μm)
Electrodes
316L SST with Ra < 15μ in. (0.38 μm)
Nickel Alloy 276 (UNS N10276) with Ra < 15μ in. (0.38 μm)
80% Platinum-20% Iridium with Ra < 15μ in. (0.38 μm)
Process connections
The Rosemount 8721 sanitary sensor is designed using a standard IDF fitting as the basis for
providing a flexible, hygienic interface for a variety of process connections. The Rosemount
8721 Sensor has the threaded or “male” end of the IDF fitting on the ends of the base sensor.
The sensor can be directly connected with user supplied IDF fittings and gaskets. If other process
connections are needed, the IDF fittings and gaskets can be provided and welded directly into
the sanitary process tubing, or can be supplied with adapters to standard Tri Clamp process
connections. All connections are PED compliant for group 2 fluids.
Tri Clamp Sanitary Coupling
IDF Sanitary Coupling (screw type)
200
Specifications and Reference Data
Reference Manual
Appendix A: Specifications and Reference Data
00809-0100-4444, Rev AD
August 2015
IDF specification per BS4825 part 4
ANSI Weld Nipple
DIN 11850 Weld Nipple
DIN 11851 (Imperial and Metric)
DIN 11864-1 form A
DIN 11864-2 form A
SMS 1145
Cherry-Burrell I-Line
Process connection material
316L Stainless Steel with Ra < 32μ in. (0.81μm)
Optional electropolished surface finish with Ra < 15μ in. (0.38μ m)
Process connection gasket material
Silicone
EPDM
Viton®
Electrical connections
Conduit entries: 1/2 in. NPT standard.
Terminal block screws: M3
Safety grounding screws: external stainless assembly, M5; internal 6-32 (No. 6)
Dimensions
See the Product Data Sheet.
Specifications and Reference Data
201
Appendix A: Specifications and Reference Data
August 2015
202
Reference Manual
00809-0100-4444, Rev AD
Specifications and Reference Data
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
Appendix B
B.1
August 2015
Product Certifications
Product certifications
Approvals Document
July 24, 2015
08732-AP01, Rev AF
Rosemount 8700M Magnetic Flowmeter Platform
Order
Code
8732EM
Transm itter Rating
8705M and 8711M/L
Flow tube Rating
Region Agency
Certification
Num ber
Ordinary Locations *
Ordinary Location *
USA
EU
FM
3048793
N5
FM Non-Incendive
Class I Div 2; DIP
FM Non-Incendive w ith Intrinsically Safe Electrodes
Class I Div 2; DIP
USA
FM
3048793
K5
FM Explosion-Proof
Class I Div 1; DIP
FM Explosion-Proof w ith Intrinsically Safe Electrodes
Class I Div 1; DIP
USA
FM
3048793
N6
CSA Non-Incendive
Class I Div 2; DIP
CSA Non-Incendive w ith Intrinsically Safe Electrodes
Class I Div 2; DIP
USA &
Canada
CSA
70030489
KU
CSA Explosion-Proof
Class I Div 1; DIP
CSA Explosion-Proof w ith Intrinsically Safe Electrodes
Class I Div 1; DIP
USA
CSA
70030489
K6
CSA Flam eproof, Increased Safety, and Dust. CSA Increased Safety w ith Intrinsically Safe Electrodes and
Canada
Zone 0 & 1
Dust. Zone 0 & 1
CSA
***
-
ND
ATEX Dust
ATEX Dust
EU
DEKRA
14ATEX0071 X
N1
ATEX Non-Sparking
ATEX Dust
ATEX Non-Sparking w ith Intrinsically Safe Electrodes
ATEX Dust
EU
DEKRA
14ATEX0071 X
K1
ATEX Flam eproof w ith Increased Safety
ATEX Dust
ATEX Increased Safety w ith Intrinsically Safe Electrodes
ATEX Dust
EU
DEKRA
14ATEX0071 X
NF
IECEx Dust
IECEx Dust
Global
DEKRA
IECEx
DEK14.0031X
N7
IECEx Non-Sparking
IECEx Dust
IECEx Non-Sparking w ith Intrinsically Safe Electrodes
IECEx Dust
Global
DEKRA
IECEx
DEK14.0031X
K7
IECEx Flam eproof w ith Increased Safety
IECEx Dust
IECEx Increased Safety w ith Intrinsically Safe Electrodes
IECEx Dust
Global
DEKRA
IECEx
DEK14.0031X
N8
EAC Non-Sparking
EAC Dust
EAC Non-Sparking w ith Intrinsically Safe Electrodes
EAC Dust
Russia
**
***
***
K8
EAC Flam eproof w ith Increased Safety
EAC Dust
EAC Increased Safety w ith Intrinsically Safe Electrodes
EAC Dust
Russia
**
***
***
N2
INMETRO Non-Sparking
INMETRO Dust
INMETRO Non-Sparking w ith Intrinsically Safe Electrodes
INMETRO Dust
Brazil
DEKRA INMETRO
DEKRA
15.0007 X
K2
INMETRO Flam eproof w ith Increased Safety
INMETRO Dust
INMETRO Increased Safety w ith Intrinsically Safe Electrodes
INMETRO Dust
Brazil
DEKRA INMETRO
DEKRA
15.0007 X
N9
KOSHA Non-Sparking
KOSHA Dust
KOSHA Non-Sparking w ith Intrinsically Safe Electrodes
KOSHA Dust
Korea
***
***
K9
KOSHA Flam eproof w ith Increased Safety
KOSHA Dust
KOSHA Increased Safety w ith Intrinsically Safe Electrodes
KOSHA Dust
Korea
***
***
N3
NEPSI Non-Sparking
NEPSI Dust
NEPSI Non-Sparking w ith Intrinsically Safe Electrodes
NEPSI Dust
China
NEPSI
GYJ15.1180X
K3
NEPSI Flam eproof w ith Increased Safety
NEPSI Dust
NEPSI Increased Safety w ith Intrinsically Safe Electrodes
NEPSI Dust
China
NEPSI
GYJ15.1180X
KN
CCOE Flam eproof w ith Increased Safety
CCOE Increased Safety w ith Intrinsically Safe Electrodes
India
PESO
P354747/1
*
**
***
Com plies w ith only the local country product safety, electrom agnetic, pressure and other applicable regulations.
Cannot be used in a classified or zoned hazardous location environm ent. No ordering code required.
Custom s Union (Russia, Belarus and Kazakhstan)
Planned subm ittal or in process w ith Agency.
Product Certifications
203
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
August 2015
Approvals Document
July 24, 2015
08732-AP01, Rev AF
Approval Markings and Logos
Symbol
Marking or
Symbol
Name
Region
Meaning of Marking or Symbol
CE
European Union
Compliance with all applicable European
Union Directives.
ATEX
European Union
Compliance with Equipment and Protective
systems intended for use in Potentially
Explosive Atmospheres directive (ATEX)
(94/9/EC)
C-tick
Australia
Compliance with Australian applicable
electromagnetic compatibility standards
FM Approved
United States
Compliance with the applicable ANSI
standards.
CSA
US = United States
Indicates that the product was tested and has
met the applicable certification requirements
for the noted countries.
C = Canada
Eurasian
Conformity
(EAC)
Eurasian Customs Union
(Russia, Belarus and
Kazakhstan)
Compliance with all of the applicable technical
regulations of the EAC Customs Union
EAC
Hazardous
Location
Eurasian Customs Union
(Russia, Belarus and
Kazakhstan)
Compliance with Technical regulation, (TR CU
012/2011) – The safety of equipment for use
in explosive environments.
INMETRO
Brazil
Compliance with all of the applicable technical
regulations of Brazil.
NEPSI
China
Compliance with all of the applicable technical
regulations of China.
KCS
Korea
Compliance with all of the applicable technical
regulations of Korea.
Ordinary Location labels will be marked with CE, C-tick, FM, CSA and EAC logos.
204
Product Certifications
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
August 2015
Approvals Document
July 24, 2015
08732-AP01, Rev AF
European Directive Information
A copy of the EC Declaration of Conformity can be found at the end of the Quick Start Guide. The most recent
revision of the EC Declaration of Conformity can be found at www.rosemount.com.
Electro Magnetic Compatibility (EMC) (2004/108/EC)
Transmitter and Flowtube: EN 61326-1: 2013
Transmitters with output code “B” require shielded cable for the 4-20mA output, with shield terminated at the
transmitter.
Low Voltage Directive (LVD) (2006/95/EC)
EN 61010-1: 2010
Ingress Protection Rating for dust and water per EN 60079-0 and EN 60529 – IP66/68 (The IP68 rating only
applies to the flowtube and the remote junction box when the transmitter is remotely mounted. The IP68 rating
does not apply to the transmitter. The IP68 rating is only valid at a depth of 10 meters for 48 hours)
European Pressure Equipment Directive (PED) (97/23/EC)
PED Certification requires the “PD” option code.
CE marked models that are ordered without the “PD” option will be marked “Not Complaint to (97/23/EC)”
Mandatory CE-marking with notified body number 0575, for all flowtubes is located on the flowmeter label.
Category I assessed for conformity per module A procedures.
Categories II – III assessed for conformity per module H procedures.
QS Certificate of Assessment
EC No. 4741-2014-CE-HOU-DNV
Module H Conformity Assessment
8705 M Flanged Flowtubes
Line size 40mm to 900mm (1½-in to 36-in)
EN 1092-1 flanges and ASME B16.5 class 150 and ASME B16.5 Class 300 flanges.
Also available in ASME B16.5 Class 600 flanges in limited line sizes.
8711 Wafer Flowtubes
Line size 40mm to 200mm (1½-in to 8-in)
All other Rosemount Flowtubes – line sizes of 25mm (1-in) and less: Sound Engineering Practice (SEP).
Flowtubes that are SEP are outside the scope of PED and cannot be marked for compliance with PED.
Product Certifications
205
Appendix B: Product Certifications
Reference Manual
00809-0100-4444, Rev AD
August 2015
Approvals Document
July 24, 2015
08732-AP01, Rev AF
Certifications
Factory Mutual (FM)
Ordinary Location Certification for FM Approvals
As standard, the transmitter and flowtube have been examined and tested to determine that the design meets
basic electrical, mechanical, and fire protection requirements by FM Approvals, a nationally recognized testing
laboratory (NRTL) as accredited by the Federal Occupational Safety and Health Administration (OSHA).
8732EM Transmitter
Note: For Intrinsically Safe (IS) 4-20mA and Pulse Outputs on the 8732EM, output code “B” must be selected.
N5
Non-Incendive for Class I, Division 2, Groups ABCD: T4
Dust-Ignition Proof for Class II/III, Division 1, Groups EFG: T5
-ƒ&”7D”ƒ&
Enclosure Type 4X, IP66
Install per drawing 08732-2062
Special Conditions for Safe Use (X):
1. Units marked with “Warning: Electrostatic Charging Hazard” may either use non-conductive paint thicker
than 0.2 mm or non-metallic labeling. Precautions shall be taken to avoid ignition due to electrostatic
charge on the enclosure.
2. The intrinsically safe 4-20mA and pulse output cannot withstand the 500V isolation test due to integral
transient protection. This must be taken into consideration upon installation.
3. Conduit entries must be installed to maintain the enclosure ingress rating of IP66.
4. Unused conduit entries must use either used the Rosemount-supplied blanking plugs, or blanking plugs
certified in accordance with the protection type.
K5
Explosion-Proof for Class I Division 1, Groups CD: T6
Non-Incendive for Class I, Division 2, Groups ABCD: T4
Dust-Ignition Proof for Class II/III, Division 1, Groups EFG: T5
-ƒ&”7D”ƒ&
Enclosure Type 4X, IP66
Install per drawing 08732-2062
Special Conditions for Safe Use (X):
1. Units marked with “Warning: Electrostatic Charging Hazard” may either use non-conductive paint thicker
than 0.2 mm or non-metallic labeling. Precautions shall be taken to avoid ignition due to electrostatic
charge on the enclosure.
2. The intrinsically safe 4-20mA and pulse output cannot withstand the 500V isolation test due to integral
transient protection. This must be taken into consideration upon installation.
3. Conduit entries must be installed to maintain the enclosure ingress rating of IP66.
4. Unused conduit entries must use either used the Rosemount-supplied blanking plugs, or blanking plugs
certified in accordance with the protection type.
206
Product Certifications
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
August 2015
Approvals Document
July 24, 2015
08732-AP01, Rev AF
8705-M and 8711-M/L Flowtube
Note: When used in hazardous (classified) locations:
The 8705-M and 8711-M/L may only be used with a certified 8732EM transmitter.
N5
Non-Incendive with Intrinsically Safe Electrodes
for Class I, Division 2, Groups ABCD: T3…T5
Dust-Ignition Proof for Class II/III, Division 1, Groups EFG: T2…T5
-ƒ&”7D”ƒ&
Enclosure Type 4X, IP66/68 (IP68 remote mount only)
Install per drawing 08732-2062
Special Conditions for Safe Use (X):
1. Units marked with “Warning: Electrostatic Charging Hazard” may either use non-conductive paint thicker
than 0.2 mm or non-metallic labeling. Precautions shall be taken to avoid ignition due to electrostatic
charge on the enclosure.
2. If used with flammable process fluid, the electrode circuit must be installed as intrinsically safe (Ex ia).
3. Conduit entries must be installed to maintain a minimum enclosure ingress rating of IP66.
4. Unused conduit entries must use either used the Rosemount-supplied blanking plugs, or blanking plugs
certified in accordance with the protection type.
K5
Explosion-Proof with Intrinsically Safe Electrodes
for Class I Division 1, Groups CD: T3…T6
Non-Incendive with Intrinsically Safe Electrodes
for Class I, Division 2, Groups ABCD: T3…T5
Dust-Ignition Proof for Class II/III, Division 1, Groups EFG: T2…T5
-ƒ&”7D”ƒ&
Enclosure Type 4X, IP66/68 (IP68 remote mount only)
Install per drawing 08732-2062
Special Conditions for Safe Use (X):
1. Units marked with “Warning: Electrostatic Charging Hazard” may either use non-conductive paint thicker
than 0.2 mm or non-metallic labeling. Precautions shall be taken to avoid ignition due to electrostatic
charge on the enclosure.
2. If used with flammable process fluid, or if installed in a Class I Division I area, the electrode circuit must
be installed as intrinsically safe (Ex ia).
3. Conduit entries must be installed to maintain a minimum enclosure ingress rating of IP66.
4. Unused conduit entries must use either used the Rosemount-supplied blanking plugs, or blanking plugs
certified in accordance with the protection type.
Product Certifications
207
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
August 2015
Approvals Document
July 24, 2015
08732-AP01, Rev AF
Canadian Standards Association (CSA)
CLASS 2258 02 - PROCESS CONTROL EQUIPMENT - For Hazardous Locations – To Canadian Requirements.
N6
N6
N6
Class I, Groups A, B, C and D (Intrinsically Safe Output and Electrode circuit)
Class I, Division 2, Groups A, B, C and D (Non-Incendive)
Class II, Division 1, Groups E, F and G (Dust Ignition Proof)
Magnetic Flow Meter – Model 8732EM Transmitter with integral or remote mount to Model 8705M or Model
8711M/L Magnetic Flow Tubes. Enclosure Type 4X and IP 66 Rated.
For Remote Mount Configuration – Temperature Code T4 with an Ambient Operating Temperature Range: -40°C
чdĂчнϲϬΣ͕ǁŝƚŚŽƌǁŝƚŚŽƵƚ>ŵĞƚĞƌ͕ǁŝƚŚŽƌǁŝƚŚŽƵƚĚŝŐŝƚĂů/ͬKĂŶĚͬŽƌƉƵůƐĞŽƵƚƉƵƚƐǁŚĞŶŝŶƐƚĂůůĞĚƉĞƌ
Rosemount Drawing 08732-2061.
For Integral Mount Configuration – Ambient Operating Temperature Range: -29°C чdĂчнϲϬΣ. Temperature
Code T3-T6 dependent on line size of Flow Tubes for Process Temperature. The T-Code is defined as per
Rosemount Drawing 08705-00CS and 08732-00CS for ‘N6’ option or ‘KU’ option.
CLASS 2258 82 - PROCESS CONTROL EQUIPMENT - For Hazardous Locations –To US Requirements
KU
N6, KU
N6, KU
N6, KU
Class I, Division 1, Groups C and D (Explosion Proof)
Class I, Groups A, B, C and D (Intrinsically Safe Output and Electrode circuit
Class I, Division 2, Groups A, B, C and D (Non-Incendive)
Class II, Division 1, Groups E, F and G (Dust Ignition Proof)
Magnetic Flow Meter – Model 8732EM Transmitter with integral or remote mount to Model 8705M or Model
8711M/L Magnetic Flow Tubes. Enclosure Type 4X and IP 66 Rated.
For Remote Mount Configuration – Temperature Code T6 for Explosion Proof, T5 for Dust Ignition Proof, and T4
for Non-Incendive. Ambient Operating Temperature Range: -ϰϬΣчdĂчнϲϬΣ͕ǁŝƚŚŽƌǁŝƚŚŽƵƚ>ŵĞƚĞƌ͕ǁŝƚŚ
or without digital I/O and/or pulse outputs when installed per Rosemount Drawing 08732-2061.
For Integral Mount Configuration – Ambient Operating Temperature Range: -ϮϵΣч dĂчнϲϬΣ. Temperature
Code T3-T6 dependent on line size of Flow Tubes for Process Temperature. The T-Code is defined as per
Rosemount Drawing 08705-00CS and 08732-00CS for ‘N6’ option or ‘KU’ option.
Special Conditions of Safe Use:
1. For use with the appropriate 8705M and 8711M/L Flow tubes only.
2. When the 8732EM transmitter is integrally mounted to 8705M or 8711M/L Flow Tubes, the ambient
temperature ranges marked on each product need to be taken into consideration before installation.
The Ambient temperature range for 8732EM transmitter is -ϰϬΣчdĂчнϲϬΣĂŶĚƚŚĞĂŵďŝĞŶƚ
temperature range for 8705M or 8711M/L Flow Tubes is -ϮϵΣчdĂчнϲϬΣ͘ Therefore, the -29°C rating
of the flow tubes will limit the overall cold temperature range of the complete system unless other
approved temperature control methods are employed.
208
Product Certifications
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
August 2015
Rosemount 8700M Magnetic Flowmeter Platform
IEC EX & ATEX Approval Document
January 29, 2015,
08732-AP02, Rev AB
1. Equipment Markings – See section VI in the tables on the following pages
a. EC-Type Examination Certificate (ATEX): DEKRA 14ATEX0071_X
b. Certificate of Conformity (IEC Ex): IEC Ex DEK 14.0031X
2. Required Documentation:
a. 08732-2060 Installation Drawing Model 8732EM, 8705M, 8711-M/L ATEX/IEC Ex Hazardous (Ex)
Locations
b. 08732-1504 Installation Drawing, 8732EM Transmitter Wiring
3. Referenced Documentation:
a. 00825-0100-4444.pdf(Hart) & 00825-0400-4444(Modbus), Quick Installation Guide
b. 00809-0100-4444.pdf, Reference Manual
c. 08732-AP01, Approvals Document
4. The Required and Referenced Documents listed above address the following items:
a. Instructions for safety i.e.
i. Putting into service
ii. Use
iii. Assembling and dismantling
iv. Maintenance, overhaul and repair
v. Installation
vi. Adjustment
b. Where necessary, training instructions
c. Details which allow a decision to be made as to whether the equipment can be used safely in the
intended area under the expected operating conditions
d. Electrical parameters, maximum surface temperatures and other limit values
i. Electrical –
1. See document 08732-2060
2.
Rosemount 8732EM Flow Transmitter
Power input
90 - 250VAC, 0.45A, 40VA
12 - 42VDC, 1.2A, 15W
Pulsed circuit
Um
Internally powered (Active): Outputs up to 12VDC, 12.1mA,
73mW Externally powered (Passive): Input up to 28VDC,
100mA, 1W
Internally Powered (Active): Outputs up to 25mA, 24VDC,
600mW Externally Powered (Passive): Input up to 25mA,
30VDC, 750mW
Internally Powered (Active): Outputs up to 100mA, 3.3VDC,
100mW
250V
Coil excitation output
500mA, 40V max, 9W max
4-20mA output circuit
MODBUS
Rosemount 8705-M and 8711-M/L Flowtube(1)
Coil excitation input
500mA, 40V max,
20W max
Electrode circuit
5V, 200uA, 1mW
(1) Provided by the transmitter
Product Certifications
209
Appendix B: Product Certifications
Reference Manual
00809-0100-4444, Rev AD
August 2015
Rosemount 8700M Magnetic Flowmeter Platform
IEC EX & ATEX Approval Document
January 29, 2015,
08732-AP02, Rev AB
e. Special Conditions for Safe Use (X):
i. For processes requiring EPL Ga and Gb, rated equipment: electrode, grounding ring, and lining
protector materials Titanium and Zirconium are not allowed.
ii. When “Special Paint Systems” are applied, instructions for safe use regarding potential
electrostatic charging hazard have to be followed.
iii. Terminals 1,2,3,4, for data communication, cannot withstand the 500 V isolation test between
signal and ground, due to integral transient protection. This must be taken into account upon
installation.
iv. Conduit entries must be installed to maintain the enclosure ingress rating of IP66.
v. In order to maintain the ingress protection level on the M3 and M4 electrode housing, the copper
crush washer that seals the electrode access plug shall be replaced when the plug is reinstalled.
The copper crush washer is one time use only.
vi. The flow tube and transmitter are not allowed to be thermally insulated.
vii. The property class of the special fasteners which attach the Magnetic Flow Tube or Transmitter
Remote Junction Box to the Magnetic Transmitter is A2-70 or A4-70 SST.
viii. For information on the dimensions of the flameproof joints the manufacturer shall be contacted.
ix. The Magnetic Flow Meter Tube contains nonconductive liners over the grounded tube. For
process requiring EPL Ga, precautions shall be taken to avoid the liner being charged by the flow
of nonconductive media.
f. Where necessary, the essential characteristics of tools which may be fitted to the equipment
g. List of the standards, including the issue date, with which the equipment is declared to comply:
i. ATEX - EN 60079-0: 2012 +A11, EN 60079-1: 2007, EN 60079-7: 2007. EN 60079-11: 2012, EN
60079-15: 2010, EN 60079-26: 2007, EN 60079-31: 2014
ii. IEC EX - IEC 60079-0: 2011, IEC 60079-1: 2007, IEC 60079-7: 2006 IEC 60079-11: 2011, IEC
60079-15: 2010, IEC 60079-26: 2006, IEC 60079-31: 2013
h. Supply wire requirements;
Use 10 - 18 AWG wire rated for the proper temperature of the application. For wire 10 - 14 AWG use lugs
or other appropriate connectors. For connections in ambient temperatures above 122°F (50 °C), use a
wire rated for 194 °F (90 °C).
i. Contact address;
i. Rosemount Inc.
12001 Technology Drive
Eden Prairie
MN 55344
United States of America
210
Product Certifications
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
August 2015
Rosemount 8700M Magnetic Flowmeter Platform
IEC EX & ATEX Approval Document
January 29, 2015,
08732-AP02, Rev AB
Nomenclature Magnetic Flow Transmitter Model 8732EM and electrical data
8732EM
I
R
II
1
III
B
IV
2
V
K1
VI
DesigExplanation
nation
I
Model
II
Transmitter Mount
III
Transmitter Power Supply
IV
Outputs
V
Conduit entries
…
M4
VII
Value
8732EM
R
T
1
2
A
B
M
1 or 4
2 or 5
K1 ATEX
K7 IECEx
N1 ATEX
VI
Safety Approval Option
N7 IECEx
ND ATEX
NF IECEx
RT50
VIII
…
SH
IX
…
V2
…
F090…
X
Explanation
Magnetic Flow Transmitter – Field Mount
Remote Mount
Integral Mount
AC (90 - 250 Vac, 50 / 60 Hz), not for Ex nA
DC (12 - 42 Vdc)
4 - 20 mA with digital HART Protocol & Scalable
Pulse Output
4 - 20 mA Intrinsically Safe Output with digital HART
Protocol & Intrinsically Safe Scalable Pulse Output
Modbus RS-485
½-14 NPT female
CM20, M20 female
II 2 (1) G Ex d e [ia Ga] IIC T6…T3 Gb
II 2 D
Ex tb IIIC T80 °C…T200 °C Db
II 2 (1) G Ex d [ia Ga] IIC T6…T3 Gb *
II 2 D
Ex tb IIIC T80 °C…T200 °C Db
Ex d e [ia Ga] IIC T6…T3 Gb
Ex tb IIIC T80 °C…T200 °C Db
Ex d [ia Ga] IIC T6…T3 Gb *
Ex tb IIIC T80 °C…T200 °C Db
II 3 (1) G Ex nA [ia Ga] IIC T4…T3 Gc ***
II 2 D
Ex tb IIIC T80 °C…T200 °C Db
Ex nA [ia Ga] IIC T4…T3 Gc ***
Ex tb IIIC T80 °C…T200 °C Db
II 2 D
Ex tb IIIC T80 °C…T200 °C Db
II 2 D
Ex tb IIIC T80 °C…T200 °C Db
II (1) G
[Ex ia Ga] IIC **
Ex tb IIIC T80 °C…T200 °C Db
Ex tb IIIC T80 °C…T200 °C Db
[Ex ia Ga] IIC **
NOTE: *
Integral Mount (see II) option only
** Intrinsically Safe Output (see IV) option only
*** DC Transmitter Power Supply only (12 - 42 Vdc)
VII
Display Option
VIII
Remote Cable Option
M4
M5
RTxx ****
RHxx ****
LOI
Display
Standard Temperature Component
Extended Temperature Component
NOTE: **** Length = xx x 10 ft, max. 500 ft
IX
Options
X
Specials
-SH
Vx
F090x
Aluminum, standard paint
Stainless Steel Electronics Housing
Special Paint Systems *****
Special Paint Systems *****
NOTE: ***** Subject to special conditions for safe use.
Product Certifications
211
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
August 2015
Rosemount 8700M Magnetic Flowmeter Platform
IEC EX & ATEX Approval Document
January 29, 2015,
08732-AP02, Rev AB
Nomenclature Magnetic Flow Tube Model 8705-M and electrical data
8705 … S A 005 … M4 K1 … G1 L1 B3 … J1 SJ … V1 … SH … F090x
I
II III IV
V VI
VII VIII IX
X XI
XII
XIII
XIV
Designation
Explanation
Value
Explanation
I
Model
8705
Magnetic Flowtube
II
Electrode Material
Custom
See special conditions for safe use
III
Electrode Types
Custom
Seal of electrodes comply with IEC 61010-1
IV
Line Size
005
to
360
½” NPS (15 mm)
to
36” NPS (900 mm)
Electrode Housing *
M0
M1
M2
M3
M4
Category 2 G or 3 G, EPL Gb or Gc
Category 2 G or 3 G, EPL Gb or Gc
Category 1/2 G or 1/3 G, EPL Ga/Gb or Ga/Gc
Category 1/2 G or 1/3 G, EPL Ga/Gb or Ga/Gc
Category 1/2 G or 1/3 G, EPL Ga/Gb or Ga/Gc
V
K1 ATEX
K7 IECEx
VI
Safety Approvals
N1 ATEX
II 1/2 G
II 2 D
Ex e ia IIC T5…T3 Ga/Gb *
Ex tb IIIC T 80 °C…T 200 °C Db
II 2 G
II 2 D
Ex e ib IIC T5…T3 Gb **
Ex tb IIIC T 80 °C…T 200 °C Db
Ex e ia IIC T5…T3 Ga/Gb *
Ex tb IIIC T 80 °C…T 200 °C Db
Ex e ib IIC T5…T3 Gb **
Ex tb IIIC T 80 °C…T 200 °C Db
line sizes 8”- 36”
II 1/3 G
II 2 D
Ex nA ia IIC T5…T3 Ga/Gc *
Ex tb IIIC T 80 °C…T 200 °C Db
II 3 G
II 2 D
Ex nA ic IIC T5…T3 Gc *
Ex tb IIIC T 80 °C…T 200 °C Db
line sizes 0.5” – 6” /
**
line sizes 8”- 36”
N7 IECEx
ND ATEX
NF IECEx
Ex nA ia IIC T5…T3 Ga/Gc *
Ex tb IIIC T 80 °C…T 200 °C Db
line sizes 0.5” – 6” /
Ex nA ic IIC T5…T3 Gc *
Ex tb IIIC T 80 °C…T 200 °C Db
II 2 D
Ex tb IIIC T 80 °C…T 200 °C Db
Ex tb IIIC T 80 °C…T 200 °C Db
NOTE: *
**
Electrode Housing M2, M3 and M4 only
Electrode Housing M0 and M1 only
VII
Grounding rings
material
Custom
See special conditions for safe use
VIII
Lining protector
material
Custom
See special conditions for safe use
IX
Mounting
Configuration
B3
Integral Mount with Model 8732EM
X
Optional conduit
entries
J1
CM20, M20 female
XI
Remote Junction Box
(RJB) material
-SJ
Aluminum, Standard Paint
316 Stainless Steel
Special paint options
Vx
Special Paint Systems ***
XII
XIII
XIV
Wrapper (housing)
material
Specials
-SH
F090x
**
Carbon Steel (w. Aluminum RJB), Standard Paint
316 Stainless Steel (w. Stainless Steel RJB)
Special Paint Systems ***
NOTE: *** Subject to special conditions for safe use.
212
Product Certifications
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
August 2015
Rosemount 8700M Magnetic Flowmeter Platform
IEC EX & ATEX Approval Document
January 29, 2015,
08732-AP02, Rev AB
Nomenclature Magnetic Flow Tube Model 8711-M/L and electrical data
8711 … S A 15F L … K1 … G1 … J1 SJ … V1 … F090x
I
II III IV V
VI
VII
VIII IX
X
XI
Designation Explanation
I
II
III
Model
Electrode Material
Electrode Types
IV
Line Size
V
Mounting
Configuration
Value
8711
Custom
Custom
015
to
080
L
M
K1
ATEX
K7 IECEx
VI
Safety Approvals
N1 ATEX
N7 IECEx
ND ATEX
NF IECEx
VII
VIII
IX
X
XI
Grounding rings
material
Optional conduit
entries
Remote Junction
Box material
Special paint
options
Specials
Custom
Explanation
Magnetic Flow Tube
See special conditions for safe use
Seal of electrodes comply with IEC 61010-1.
1½” NPS (40 mm)
to
8” NPS (900 mm)
Remote Mount from Transmitter
Integral Mount with Transmitter
II 2 G
Ex e ib IIC T5…T3 Gb
II 2 D
Ex tb IIIC T 80 °C…T 200 °C Db
Ex e ib IIC T5…T3 Gb
Ex tb IIIC T 80 °C…T 200 °C Db
II 3 G
Ex nA ic IIC T5…T3 Gc
II 2 D
Ex tb IIIC T 80 °C…T 200 °C Db
Ex nA ic IIC T5…T3 Gc
Ex tb IIIC T 80 °C…T 200 °C Db
II 2 D
Ex tb IIIC T 80 °C…T 200 °C Db
Ex tb IIIC T 80 °C…T 200 °C Db
See special conditions for safe use
J1
CM20, M20 female
-SJ
Aluminum, Standard Paint *
316 Stainless Steel *
NOTE:* Flowtube with Carbon Steel Wrapper (housing)
Vx
Special Paint Systems **
F090x
Special Paint Systems **
NOTE: ** Subject to special conditions for safe use.
Product Certifications
213
Appendix B: Product Certifications
B.2
214
Reference Manual
00809-0100-4444, Rev AD
August 2015
FM hazardous locations
Product Certifications
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Appendix B: Product Certifications
August 2015
215
Appendix B: Product Certifications
August 2015
216
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Appendix B: Product Certifications
August 2015
217
Appendix B: Product Certifications
August 2015
218
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Reference Manual
Appendix B: Product Certifications
00809-0100-4444, Rev AD
B.3
Product Certifications
August 2015
ATEX/IECEx hazardous locations
219
Appendix B: Product Certifications
August 2015
220
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Appendix B: Product Certifications
August 2015
221
Appendix B: Product Certifications
August 2015
222
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Appendix B: Product Certifications
August 2015
223
Appendix B: Product Certifications
August 2015
224
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Appendix B: Product Certifications
August 2015
225
Appendix B: Product Certifications
August 2015
226
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Reference Manual
00809-0100-4444, Rev AD
Product Certifications
Appendix B: Product Certifications
August 2015
227
Appendix B: Product Certifications
B.4
Reference Manual
00809-0100-4444, Rev AD
August 2015
EC Declaration of Conformity
Approvals Document
July 24, 2015
08732-AP01, Rev AF
228
Product Certifications
Reference Manual
00809-0100-4444, Rev AD
Appendix B: Product Certifications
August 2015
Approvals Document
July 24, 2015
08732-AP01, Rev AF
Product Certifications
229
Appendix B: Product Certifications
August 2015
Reference Manual
00809-0100-4444, Rev AD
Approvals Document
July 24, 2015
08732-AP01, Rev AF
230
Product Certifications
Reference Manual
Appendix C: Wiring Diagrams
00809-0100-4444, Rev AD
Appendix C
C.1
August 2015
Wiring Diagrams
8732EM wiring diagrams
Figure C-1. 8732EM Wiring Diagram—Component Cables
Wiring Diagrams
231
Appendix C: Wiring Diagrams
August 2015
Reference Manual
00809-0100-4444, Rev AD
Figure C-2. 8732EM Wiring Diagram—Combination Cable
232
Wiring Diagrams
Reference Manual
Appendix C: Wiring Diagrams
00809-0100-4444, Rev AD
C.2
August 2015
775 Smart Wireless THUM™ Adapter wiring
diagrams
Figure C-3. Wiring Diagram—775 Smart Wireless THUM Adapter with 8732EM Internal Analog Power
Wiring Diagrams
233
Appendix C: Wiring Diagrams
August 2015
Reference Manual
00809-0100-4444, Rev AD
Figure C-4. Wiring Diagram—775 Smart Wireless THUM Adapter with 8732EM External Analog Power
234
Wiring Diagrams
Reference Manual
Appendix C: Wiring Diagrams
00809-0100-4444, Rev AD
C.3
August 2015
475 Field Communicator wiring diagrams
Figure C-5. Wiring Diagram—475 Field Communicator with 8732EM Internal Analog Power
Wiring Diagrams
235
Appendix C: Wiring Diagrams
August 2015
Reference Manual
00809-0100-4444, Rev AD
Figure C-6. Wiring Diagram—475 Field Communicator with 8732EM External Analog Power
236
Wiring Diagrams
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
Appendix D
Implementing a Universal
Transmitter
Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 237
Rosemount sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 240
Brooks sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 243
Endress and Hauser sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 245
Fischer and Porter sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 246
Foxboro sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 252
Kent Veriflux VTC sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 256
Kent sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 257
Krohne sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 258
Taylor sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 259
Yamatake Honeywell sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 261
Yokogawa sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 262
Generic manufacturer sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 263
D.1
Safety messages
Instructions and procedures in this section may require special precautions to ensure the safety
of the personnel performing the operations. Please read the following safety messages before
performing any operation described in this section.


D.2
The Rosemount 8732EM Transmitter has not been evaluated for use with other
manufacturers' magnetic flowmeter sensors in hazardous (Ex or Classified) areas.
Special care should be taken by the end-user and installer to ensure the 8732EM
transmitter meets the safety and performance requirements of the other manufacturer’s
equipment.
Universal capability
The 8732EM transmitter has the ability to drive other manufacturers' sensors and report a flow
rate. In addition to providing a flow measurement, all of the diagnostic functionality is also
available in a universal application. This capability can provide additional information into the
installation, process, and meter health, in addition to enabling a common maintenance practice
for all magnetic flowmeter installations and helping to reduce spares inventory of magnetic
flowmeter transmitters.
This section details how to wire the transmitter to other manufacturers' sensors and configure
the universal capabilities.
Implementing a Universal Transmitter
237
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.2.1
Implementation
There are three easy steps when implementing a universal transmitter.
1.
Review the existing application. Verify the existing sensor is in good working order, and
that it is compatible with a universal transmitter. Use Table D-1to help verify if the
Rosemount universal transmitter is compatible with the existing sensor. Verifying the
sensor is functioning correctly. While the universal transmitter may be able to drive the
existing sensor, if the sensor is not in good working order the universal transmitter may
not function correctly.
2.
Connect the universal transmitter to the existing sensor using the wiring diagrams in
this appendix. If the existing sensor is not listed in this appendix, contact Rosemount
technical support for more details on the application of the universal capabilities.
3.
Configure the transmitter following the guidelines in Section 4 and Section 5, setting
up parameters as needed. One of the key configuration parameters is the sensor
calibration number. There are several methods to determine the calibration number,
but the most common method will be to use the universal trim capability. This
functionality is detailed in this appendix. Accuracy of the meter when the universal trim
is used to determine the calibration number will be dependent on the accuracy of the
known flow rate used in the trim process.
In addition to the universal trim, there are two other methodologies for determining a
calibration number for the sensor.
Method 1: Have the sensor sent to a Rosemount service center for determination of a
calibration number compatible with the universal transmitter. This is the most accurate method
for determining the calibration number and will provide a ±0.5% of rate measurement accuracy
from 3 to 40 fps (1-10 m/s).
Method 2: Involves the conversion of the existing sensor calibration number/meter factors to
an equivalent Rosemount 16-digit calibration number. Accuracy of the meter using this
methodology is estimated to be in the range of 2-3%. Contact the Rosemount technical support
for more information on this method or to determine a calibration number for the existing
sensor.
Once these steps are completed, the meter will begin measuring flow. Verify the measured flow
rate is within the expected range and that the mA output correctly corresponds to the
measured flow rate. Also verify the reading in the control system matches the reading at the
transmitter. Once these items have been verified, the loop can be placed into automatic control
as needed.
Universal trim
LOI menu path
Diagnostics, Trims, Universal Trim
Fast keys
1, 2, 5, 5
The universal auto trim function enables the Rosemount 8732 to determine a calibration
number for sensors that were not calibrated at the Rosemount factory. The function is activated
as one step in a procedure known as in-process calibration. If the sensor has a 16-digit
Rosemount calibration number, in-process calibration is not required.
1.
238
Determine the flow rate of the process fluid in the sensor.
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
Note
The flow rate in the line can be determined by using another sensor in the line, by counting the
revolutions of a centrifugal pump, or by performing a bucket test to determine how fast a given
volume is filled by the process fluid.
2.
Complete the universal auto trim function.
3.
When the routine is completed, the sensor is ready for use.
Wiring the universal transmitter
The wiring diagrams in this section illustrate the proper connections between the transmitter
and most sensors currently on the market. Specific diagrams are included for most models, and
where information for a particular model of a manufacturer is not available, a generic drawing
pertaining to that manufacturer's sensors is provided. If the manufacturer for the existing
sensor is not included, see the drawing for generic connections.
Table D-1. Transmitter and Sensor Reference
Rosemount transmitter
Sensor manufacturer
Page number
Rosemount 8732
Rosemount 8705, 8707, 8711
page 240
Rosemount 8732
Rosemount 8701
page 241
Rosemount 8732
Model 5000
page 243
Rosemount 8732
Model 7400
page 244
Generic Wiring for Sensor
page 245
Rosemount 8732
Model 10D1418
page 246
Rosemount 8732
Model 10D1419
page 247
Rosemount 8732
Model 10D1430 (Remote)
page 248
Rosemount 8732
Model 10D1430
page 249
Rosemount 8732
Model 10D1465, 10D1475 (Integral)
page 250
Rosemount 8732
Generic Wiring for Sensors
page 251
Rosemount 8732
Series 1800
page 252
Rosemount 8732
Series 1800 (Version 2)
page 253
Rosemount 8732
Series 2800
page 254
Rosemount 8732
Generic Wiring for Sensors
page 255
Rosemount 8732
Veriflux VTC
page 256
Rosemount 8732
Generic Wiring for Sensors
page 257
Generic Wiring for Sensors
page 258
Rosemount 8732
Series 1100
page 260
Rosemount 8732
Generic Wiring for Sensors
page 260
Generic Wiring for Sensors
page 261
Generic Wiring for Sensors
page 262
Generic Wiring for Sensors
page 263
Rosemount
Brooks
Endress and Hauser
Rosemount 8732
Fischer and Porter
Foxboro
Kent
Krohne
Rosemount 8732
Taylor
Yamatake Honeywell
Rosemount 8732
Yokogawa
Rosemount 8732
Generic Manufacturer Wiring
Rosemount 8732
Implementing a Universal Transmitter
239
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.3
Rosemount sensors
D.3.1
8705/8707/8711/8721 sensors to 8732 Transmitter
To connect a Rosemount 8705/8707/8711/8721 Sensor to a Rosemount 8732 Transmitter,
connect coil drive and electrode cables as shown in Figure D-1 on page 240.
Figure D-1. Wiring Diagram to a Rosemount 8732 Transmitter
Table D-2. Rosemount 8705/8707/8711/8721 Sensor Wiring Connections
Rosemount 8732 transmitters
Rosemount 8705/8707/8711/8721 sensors
1
2
3
17
18
19
1
2
3
17
18
19
Do not connect mains or line power to the
magnetic flowtube sensor or to the
transmitter coil excitation circuit.
240
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.3.2
8701 sensor to 8732 Transmitter
To connect a Rosemount 8701 Sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-2.
Figure D-2. Wiring Diagram for Rosemount 8701 Sensor and Rosemount 8732 Transmitter
Rosemount 8701 sensor
Rosemount 8732 Transmitter
17 1
1
18 2
2
19
3
17
18
19
Refer to Figure D-1 on page 240 for actual
terminal block configuration drawing.
Table D-3. Rosemount 8701 Sensor Wiring Connections
Rosemount 8732
Rosemount 8701 sensors
1
2
3
17
18
19
1
2
3
17
18
19
Do not connect mains or line power to the
magnetic flowtube sensor or to the
transmitter coil excitation circuit.
Implementing a Universal Transmitter
241
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.3.3
Connecting sensors of other manufacturers
Before connecting another manufacturer’s sensor to the transmitter, it is necessary to perform
the following functions.
1.
Turn off the AC power to the sensor and transmitter. Failure to do so could result in
electrical shock or damage to the transmitter.
2.
Verify the coil drive cables between the sensor and the transmitter are not connected
to any other equipment.
3.
Label the coil drive cables and electrode cables for connection to the transmitter.
4.
Disconnect the wires from the existing transmitter.
5.
Remove the existing transmitter. Mount the new transmitter. See “Installation” on
page 3.
6.
Verify the sensor coil is configured for series connection. Other manufacturers sensors
may be wired in either a series or parallel circuit. All Rosemount magnetic sensors are
wired in a series circuit. (Other manufacturers AC sensors (AC coils) wired for 220VAC
operation are typically wired in parallel and must be rewired in series.)
7.
Verify the sensor is in good working condition. Use the manufacturer’s recommended
test procedure for verification of sensor condition. Perform the basic checks:
a. Check the coils for shorts or open circuits.
b. Check the sensor liner for wear or damage.
c. Check the electrodes for shorts, leaks, or damage.
d. Connect the sensor to the transmitter in accordance with reference wiring
diagrams. See Appendix A: Implementing a Universal Transmitter for specific
drawings.
e. Connect and verify all connections between the sensor and the transmitter, then
apply power to the transmitter.
f.
Perform the Universal Auto Trim function.
Do not connect mains or line
power to the magnetic
flowtube sensor or to the
transmitter coil excitation
circuit.
242
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.4
Brooks sensors
D.4.1
Model 5000 sensor to 8732 Transmitter
To connect a Model 5000 sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-3.
Figure D-3. Wiring Diagram for Brooks Sensor Model 5000 and Rosemount 8732
Brooks Model 5000
Rosemount 8732 Transmitter
19
18
17
3
2
1
Refer to Figure D-1 on page 240 for actual terminal
block configuration drawing.
Table D-4. Brooks Model 5000 Sensor Wiring Connections
Rosemount 8732
Brooks sensors Model 5000
1
2
3
17
18
19
1
2
3
17
18
19
Do not connect mains or line power to the
magnetic flowtube sensor or to the
transmitter coil excitation circuit.
Implementing a Universal Transmitter
243
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.4.2
Model 7400 sensor to 8732 Transmitter
To connect a Model 7400 sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-4.
Figure D-4. Wiring Diagram for Brooks Sensor Model 7400 and Rosemount 8732
BROOKS MODEL 7400
ROSEMOUNT 8732
TRANSMITTER
19
18
17
3
2
1
Refer to Figure D-1 on page 240 for actual
terminal block configuration drawing.
Table D-5. Brooks Model 7400 sensor Wiring Connections
Rosemount 8732
Brooks Sensors Model 7400
1
2
3
17
18
19
Coils +
Coils –
3
Shield
Electrode +
Electrode –
Do not connect mains or line power to
the magnetic flowtube sensor or to the
transmitter coil excitation circuit.
244
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.5
Endress and Hauser sensors
D.5.1
Endress and Hauser sensor to 8732 Transmitter
To connect an Endress and Hauser sensor to a Rosemount 8732 Transmitter, connect coil drive
and electrode cables as shown in Figure D-5.
Figure D-5. Wiring Diagram for Endress and Hauser Sensors and Rosemount 8732
ENDRESS AND HAUSER
SENSORS
Coils
ROSEMOUNT 8732
TRANSMITTER
41
1
42
2
3
Electrodes
4
17
5
18
7
19
Refer to Figure D-1 on page 240 for actual terminal
block configuration drawing.
Table D-6. Endress and Hauser Sensor Wiring Connections
Rosemount 8732
Endress and Hauser sensors
1
41
2
42
3
14
17
4
18
5
19
7
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
Implementing a Universal Transmitter
245
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.6
Fischer and Porter sensors
D.6.1
Model 10D1418 sensor to 8732 transmitter
To connect a Model 10D1418 sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-6.
Figure D-6. Wiring Diagram for Fischer and Porter Sensor Model 10D1418 and Rosemount
8732
Electrode Connections
ROSEMOUNT 8732 TRANSMITTER
3
2
19
1
18
17
3
U1
U2
2
G
1
L1
L2
8
Coil Connections
6
7
Refer to Figure D-1 on page 240 for actual
terminal block configuration drawing.
5
Table D-7. Fischer and Porter Model 10D1418 Sensor Wiring Connections
Rosemount 8732
Fischer and Porter Model 10D1418 sensors
1
2
3
17
18
19
L1
L2
Chassis Ground
3
1
2
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
246
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.6.2
Model 10D1419 sensor to 8732 Transmitter
To connect a Model 10D1419 sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-7.
Figure D-7. Wiring Diagram for Fischer and Porter Sensor Model 10D1419 and Rosemount
8732
Electrode Connections
ROSEMOUNT 8732 TRANSMITTER
3
2
19
1
18
16
17
17
3
18
2
L1
1
L2
Refer to Figure D-1 on page 240 for actual
terminal block configuration drawing.
Coil Connections
Table D-8. Fischer and Porter Model 10D1419 Sensor Wiring Connections
Rosemount 8732
Fischer and Porter Model 10D1419 sensors
1
2
3
17
18
19
L1
L2
3
3
1
2
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
Implementing a Universal Transmitter
247
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.6.3
Model 10D1430 sensor to 8732 Transmitter
To connect a Model 10D1430 sensor (Remote) to a Rosemount 8732 Transmitter, connect coil
drive and electrode cables as shown in Figure D-8.
Figure D-8. Wiring Diagram for Fischer and Porter Sensor Model 10D1430 (Remote) and
Rosemount 8732
Electrode Connections
ROSEMOUNT 8732 TRANSMITTER
1
2
19
3
18
17
3
G
2
L1
1
8
Coil Connections
Refer to Figure D-1 on page 240 for actual
terminal block configuration drawing.
Table D-9. Fischer and Porter Model 10D1430 (Remote) Sensor Wiring Connections
Rosemount 8732
Fischer and Porter Model 10D1430
(Remote) sensors
1
2
3
17
18
19
L1
8
G
3
1
2
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
248
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.6.4
Model 10D1430 sensor to 8732 Transmitter
To connect a Model 10D1430 sensor (integral) to a Rosemount 8732 Transmitter, connect coil
drive and electrode cables as shown in Figure D-9.
Figure D-9. Wiring Diagram for Fischer and Porter Sensor Model 10D1430 (Integral) and
Rosemount 8732
Electrode Connections
ROSEMOUNT 8732 TRANSMITTER
1
19
2
3
1
2
3
18
17
7
6
7
6
8
3
2
L2
To L2
L2
L1
1
L1
U2
U1
G
U2
U1
Coil Connections
TB2
TB1
Refer to Figure D-1 on page 240 for actual terminal
block configuration drawing.
To Calibration Device
(Disconnect)
Table D-10. Fischer and Porter Model 10D1430 (integral) Sensor Wiring Connections
Rosemount 8732
Fischer and Porter Model 10D1430 (Integral) sensors
1
2
3
17
18
19
L1
L2
G
3
1
2
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
Implementing a Universal Transmitter
249
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.6.5
Model 10D1465/10D1475 sensors to 8732 Transmitter
To connect a Model 10D1465 or 10D1475 sensor (integral) to a Rosemount 8732 Transmitter,
connect coil drive and electrode cables as shown in Figure D-10.
Figure D-10. Wiring Diagram for Fischer and Porter Sensor Model 10D1465 and Model
10D1475 (integral) and Rosemount 8732
Electrode
Connections
ROSEMOUNT 8732 TRANSMITTER
2A
Disconnect
2
19
1
18
5
17
6
3
16
3
1
2
CT
M2
M1
MR
Coil Connections
Refer to Figure D-1 on page 240 for actual terminal block
configuration drawing.
Table D-11. Fischer and Porter Model 10D1465 and 10D1475 Sensor Wiring Connections
Rosemount 8732
Fischer and Porter Model 10D1465 and
10D1475 sensors
1
2
3
17
18
19
M1
MR
3
3
1
2
Do not connect mains or line power to the
magnetic flowtube sensor or to the
transmitter coil excitation circuit.
250
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.6.6
Fischer and Porter sensor to 8732 Transmitter
To connect a Fischer and Porter sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-11.
Figure D-11. Generic Wiring Diagram for Fischer and Porter Sensors and Rosemount 8732
FISCHER AND PORTER
SENSORS
ROSEMOUNT 8732
TRANSMITTER
Electrodes
19
2
18
1
17
3
Coils
Chassis
3
M2
2
M1
1
Refer to Figure D-1 on page 240 for actual terminal
block configuration drawing.
Table D-12. Fischer and Porter Generic Sensor Wiring Connections
Rosemount 8732
Fischer and Porter sensors
1
2
3
17
18
19
M1
M2
Chassis Ground
3
1
2
Do not connect mains or line power
to the magnetic flowtube sensor or
to the transmitter coil excitation
circuit.
Implementing a Universal Transmitter
251
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.7
Foxboro sensors
D.7.1
Series 1800 sensor to 8732 Transmitter
To connect a Series 1800 sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-12.
Figure D-12. Wiring Diagram for Foxboro Series 1800 and Rosemount 8732
FOXBORO SERIES 1800
SENSOR
Electrode Connections
ROSEMOUNT 8732
TRANSMITTER
White Lead
Outer Shield
White Shield
19
18
17
3
2
Black Lead
Black Shield
Inner Shield
1
Refer to Figure D-1 on page 240 for actual
terminal block configuration drawing.
Coil Connections
Table D-13. Foxboro Series1800 Sensor Wiring Connections
Rosemount 8732
Foxboro Series 1800 sensors
1
2
3
17
18
19
L1
L2
Chassis Ground
Any Shield
Black
White
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
252
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.7.2
Series 1800 sensor to 8732 Transmitter
To connect a Series 1800 (version 2) sensor to a Rosemount 8732 Transmitter, connect coil drive
and electrode cables as shown in Figure D-13.
Figure D-13. Wiring Diagram for Foxboro Series 1800 (Version 2) and Rosemount 8732
FOXBORO SERIES
1800 SENSOR
(VERSION 2)
ROSEMOUNT
8732
TRANSMITTER
White
19
Black
Shield
18
17
3
2
1
Electrode
Connections
GND
L2
L1
Coil Connections
Refer to Figure D-1 on page 240 for
actual terminal block configuration
drawing.
Table D-14. Foxboro Series 1800 (Version 2) Sensor Wiring Connections
Rosemount 8732
Foxboro Series 1800 sensors
1
2
3
17
18
19
L1
L2
Chassis Ground
Any Shield
Black
White
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
Implementing a Universal Transmitter
253
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.7.3
Series 2800 Sensor to 8732 Transmitter
To connect a Series 2800 Sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-14.
Figure D-14. Wiring Diagram for Foxboro Series 2800 and Rosemount 8732
FOXBORO SERIES 2800
SENSOR
ROSEMOUNT 8732
TRANSMITTER
Electrode Connections
Outer Shield
White Lead
White Shield
White
Black
19
18
Any Shield
17
3
Black Lead
Black Shield
Inner Shield
2
1
L2
L1
G
Coil Connections
Refer to Figure D-1 on page 240 for
actual terminal block configuration
drawing.
Table D-15. Foxboro Series 2800 Sensor Wiring Connections
Rosemount 8732
Foxboro Series 2800 Sensors
1
2
3
17
18
19
L1
L2
Chassis Ground
Any Shield
Black
White
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
254
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.7.4
Foxboro Sensor to 8732 Transmitter
To connect a Foxboro Sensor to a Rosemount 8732 Transmitter, connect coil drive and electrode
cables as shown in Figure D-15.
Figure D-15. Generic Wiring Diagram for Foxboro Sensors and Rosemount 8732
FOXBORO SENSOR
ROSEMOUNT 8732
TRANSMITTER
White
19
Black
18
Any Shield
17
Electrodes
Coils
Ground
3
L2
2
L1
1
Refer to Figure D-1 on page 240 for actual
terminal block configuration drawing.
Table D-16. Foxboro Generic Sensor Wiring Connections
Rosemount 8732
Foxboro sensors
1
2
3
17
18
19
L1
L2
Chassis Ground
Any Shield
Black
White
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
Implementing a Universal Transmitter
255
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.8
Kent Veriflux VTC sensor
D.8.1
Veriflux VTC sensor to 8732 Transmitter
To connect a Veriflux VTC sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-16.
Figure D-16. Wiring Diagram for Kent Veriflux VTC Sensor and Rosemount 8732
KENT VERIFLUX VTC
SENSOR
ROSEMOUNT 8732
TRANSMITTER
Electrode Connections
19
18
17
1SCR OUT
2
3 SIG 1
4 SIG 2
5
6
3
2
1
1
2–
5+
6 SCR OUT
Refer to Figure D-1 on page 240 for
actual terminal block configuration
drawing.
Coil Connections
Table D-17. Kent Veriflux VTC Sensor Wiring Connections
Rosemount 8732
Kent Veriflux VTC sensors
1
2
3
17
18
19
2
1
SCR OUT
SCR OUT
SIG1
SIG2
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
256
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.9
Kent sensors
D.9.1
Kent sensor to 8732 Transmitter
To connect a Kent sensor to a Rosemount 8732 Transmitter, connect coil drive and electrode
cables as shown in Figure D-17.
Figure D-17. Generic Wiring Diagram for Kent Sensors and Rosemount 8732
KENT SENSORS
ROSEMOUNT 8732
TRANSMITTER
SIG2
19
SIG1
18
SCR OUT
17
Electrodes
SCR OUT
3
2
2
1
1
Coils
Refer to Figure D-1 on page 240 for
actual terminal block configuration
drawing.
Table D-18. Kent Sensor Wiring Connections
Rosemount 8732
Kent sensors
1
2
3
17
18
19
1
2
SCR OUT
SCR OUT
SIG1
SIG2
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
Implementing a Universal Transmitter
257
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.10
Krohne sensors
D.10.1
Krohne sensor to 8732 Transmitter
To connect a Krohne sensor to a Rosemount 8732 Transmitter, connect coil drive and electrode
cables as shown in Figure D-18.
Figure D-18. Generic Wiring Diagram for Krohne Sensors and Rosemount 8732
ROSEMOUNT 8732
TRANSMITTER
KROHNE SENSORS
3
19
2
18
Electrode Shield
17
Electrodes
Coil Shield
3
7
2
8
1
Coils
Refer to Figure D-1 on page 240 for
actual terminal block configuration
drawing.
Table D-19. Krohne Sensor Wiring Connections
Rosemount 8732
Krohne sensors
1
2
3
17
18
19
8
7
Coil Shield
Electrode Shield
2
3
Do not connect mains or line power to the magnetic
flowtube sensor or to the transmitter coil excitation
circuit.
258
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.11
Taylor sensors
D.11.1
Series 1100 sensor to 8732 Transmitter
To connect a Series 1100 sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-19.
Figure D-19. Wiring Diagram for Taylor Series 1100 Sensors and Rosemount 8732
TAYLOR SERIES 1100 SENSOR
ROSEMOUNT 8732
TRANSMITTER
Electrode Connections
19
C
L
A
18
17
3
2
1
LNG1234
White
Black
Green
Coil Connections
Refer to Figure D-1 on page 240 for actual
terminal block configuration drawing.
Table D-20. Taylor Series 1100 Sensor Wiring Connections
Rosemount 8732
Taylor Series 1100 sensors
1
2
3
17
18
19
Black
White
Green
S1 and S2
E1
E2
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
Implementing a Universal Transmitter
259
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.11.2
Taylor sensor to 8732 Transmitter
To connect a Taylor sensor to a Rosemount 8732 Transmitter, connect coil drive and electrode
cables as shown in Figure D-20.
Figure D-20. Generic Wiring Diagram for Taylor Sensors and Rosemount 8732
TAYLOR SENSORS
ROSEMOUNT 8732
TRANSMITTER
E2
19
E1
18
S1 and S2
17
Electrodes
Coils
Green
3
White
2
Black
1
Refer to Figure D-1 on page 240 for actual
terminal block configuration drawing.
Table D-21. Taylor Sensor Wiring Connections
Rosemount 8732
Taylor sensors
1
2
3
17
18
19
Black
White
Green
S1 and S2
E1
E2
Do not connect mains or line power to the magnetic
flowtube sensor or to the transmitter coil excitation
circuit.
260
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.12
Yamatake Honeywell sensors
D.12.1
Yamatake Honeywell sensor to 8732 Transmitter
To connect a Yamatake Honeywell sensor to a Rosemount 8732 Transmitter, connect coil drive
and electrode cables as shown in Figure D-21.
Figure D-21. Generic Wiring Diagram for Yamatake Honeywell Sensors and Rosemount
8732
ROSEMOUNT 8732
TRANSMITTER
YAMATAKE
HONEYWELL
SENSORS
Electrodes
A
19
B
18
C
17
Chassis Ground
Coils
3
Y
2
X
1
Refer to Figure D-1 on page 240 for actual terminal
block configuration drawing.
Table D-22. Yamatake Honeywell Sensor Wiring Connections
Rosemount 8732
Yamatake Honeywell sensors
1
2
3
17
18
19
X
Y
Chassis Ground
C
B
A
Do not connect mains or line power to the
magnetic flowtube sensor or to the transmitter
coil excitation circuit.
Implementing a Universal Transmitter
261
Reference Manual
Appendix D: Implementing a Universal Transmitter
00809-0100-4444, Rev AD
August 2015
D.13
Yokogawa sensors
D.13.1
Yokogawa sensor to 8732 Transmitter
To connect a Yokogawa sensor to a Rosemount 8732 Transmitter, connect coil drive and
electrode cables as shown in Figure D-22.
Figure D-22. Generic Wiring Diagram for Yokogawa Sensors and Rosemount 8732
ROSEMOUNT 8732
TRANSMITTER
YOKOGAWA
SENSORS
Electrodes
A
19
B
18
C
17
Chassis Ground
3
Ex 2
2
Ex 1
1
Coils
Refer to Figure D-1 on page 240 for
actual terminal block configuration
drawing.
Table D-23. Yokogawa Sensor Wiring Connections
Rosemount 8732
Yokogawa sensors
1
2
3
17
18
19
EX1
EX2
Chassis Ground
C
B
A
Do not connect mains or line
power to the magnetic flowtube
sensor or to the transmitter coil
excitation circuit.
262
Implementing a Universal Transmitter
Appendix D: Implementing a Universal Transmitter
Reference Manual
August 2015
00809-0100-4444, Rev AD
D.14
Generic manufacturer sensor to 8732 Transmitter
D.14.1
Identify the terminals
First check the sensor manufacturer’s manual to identify the appropriate terminals. Otherwise,
perform the following procedure.
Identify coil and electrode terminals
1.
Select a terminal and touch an ohmmeter probe to it.
2.
Touch the second probe to each of the other terminals and record the results for each
terminal.
3.
Repeat the process and record the results for every terminal.
Coil terminals will have a resistance of approximately 3-300 ohms.
Electrode terminals will have an open circuit.
Identify a chassis ground
1.
Touch one probe of an ohmmeter to the sensor chassis.
2.
Touch the other probe to the each sensor terminal and the record the results for each
terminal.
The chassis ground will have a resistance value of one ohm or less.
D.14.2
Wiring connections
Connect the electrode terminals to Rosemount 8732 terminals 18 and 19. The electrode shield
should be connected to terminal 17.
Connect the coil terminals to Rosemount 8732 terminals 1, 2, and 3.
If the Rosemount 8732 Transmitter indicates a reverse flow condition, switch the coil wires
connected to terminals 1 and 2.
Do not connect mains or line
power to the magnetic flowtube
sensor or to the transmitter coil
excitation circuit.
Implementing a Universal Transmitter
263
Appendix D: Implementing a Universal Transmitter
August 2015
264
Reference Manual
00809-0100-4444, Rev AD
Implementing a Universal Transmitter
Reference Manual
Index
00809-0100-4444, Rev AD
August 2015
Index
A
G
Analog Output
range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Analog Output Adjustment . . . . . . . . . . . . . . . . . . . . . 181
Analog Output Test . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Applications/Configurations . . . . . . . . . . . . . . . . . . . . . . 5
Auxiliary Output . . . . . . . . . . . . . . . . . . . . . . . . . .182, 183
Gaskets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 17
Grounding
Grounding Electrodes . . . . . . . . . . . . . . . . . . . . . . . 20
Grounding Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lining Protectors. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
B
Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Bolts
Flanged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
C
Conductivity
Model 8705/8707 . . . . . . . . . . . . . . . . . . . . . . . . . 189
Model 8711 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Configurations/Applications . . . . . . . . . . . . . . . . . . . . . . 5
Cover Gasket, Materials of Construction . . . . . . . . . . . 186
D
Device Software Functions
basic setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
F
Fast Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Flange Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Flow Rate
units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Flowtube
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Flowtubes
Brooks Model 5000 . . . . . . . . . . . . . . . . . . . . . . . . 243
Endress and Hauser Models . . . . . . . . . . . . . . . . . 242
Fischer and Porter Model 10D1418 . . . . . . . . . . . 246
Foxboro Series 1800 . . . . . . . . . . . . . . . . . . . . . . . 252
Generic Flowtube . . . . . . . . . . . . . . . . . . . . . . . . . 263
Kent Flowtubes . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Kent Veriflux VTC . . . . . . . . . . . . . . . . . . . . . . . . . 256
Krohne Flowtubes . . . . . . . . . . . . . . . . . . . . . . . . . 258
Taylor Series 1100 . . . . . . . . . . . . . . . . . . . . . . . . . 259
Yamatake Honeywell Flowtubes. . . . . . . . . . . . . . 261
Yokogawa Flowtubes . . . . . . . . . . . . . . . . . . . . . . 262
Index
I
Installation
mechanical considerations . . . . . . . . . . . . . . . . . . . . .5
Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Wafer Flowtube
Flange Bolts . . . . . . . . . . . . . . . . . . . . . . . . . .19
L
Lining Protectors
Grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Local Operator Interface (LOI)
Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
M
Mechanical Considerations . . . . . . . . . . . . . . . . . . . . . . . .5
Messages
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
O
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Orientation
Flowtube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Output Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
P
Paint, Materials of Construction. . . . . . . . . . . . . . . . . .
Power Supply Load Limitations . . . . . . . . . . . . . . . . . .
Pressure
Model 8705/8707 . . . . . . . . . . . . . . . . . . . . . . . . .
Model 8711 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pulse Output Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
186
182
189
195
182
265
Reference Manual
Index
00809-0100-4444, Rev AD
August 2015
S
W
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Specifications
Model 8705 and Model 8707
ambient temperature limits . . . . . . . . . . . 189
conductivity limits . . . . . . . . . . . . . . . . . . . 189
electrical connections . . . . . . . . . . . . . . . . 193
electrodes . . . . . . . . . . . . . . . . . . . . . . . . . 191
functional specifications . . . . . . . . . . . . . . 188
grounding rings . . . . . . . . . . . . . . . . . . . . . 193
interchangeability . . . . . . . . . . . . . . . . . . . 188
line sizes. . . . . . . . . . . . . . . . . . . . . . . . . . . 188
lining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
lining protectors . . . . . . . . . . . . . . . . . . . . 193
non-wetted materials . . . . . . . . . . . . . . . . 191
performance specifications . . . . . . . . . . . . 190
physical specifications . . . . . . . . . . . . . . . . 191
pressure limits . . . . . . . . . . . . . . . . . . . . . . 189
process conditions. . . . . . . . . . . . . . . . . . . 192
process temperature limits . . . . . . . . . . . . 188
process wetted materials . . . . . . . . . . . . . 191
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
upper range limit . . . . . . . . . . . . . . . . . . . . 188
vacuum limits . . . . . . . . . . . . . . . . . . . . . . 189
weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Model 8711
ambient temperature limits . . . . . . . . . . . 195
conductivity limits . . . . . . . . . . . . . . . . . . . 195
electrodes . . . . . . . . . . . . . . . . . . . . . . . . . 196
functional specifications . . . . . . . . . . . . . . 194
interchangeability . . . . . . . . . . . . . . . . . . . 194
line sizes. . . . . . . . . . . . . . . . . . . . . . . . . . . 194
lining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
non-wetted materials . . . . . . . . . . . . . . . . 195
physical specifications . . . . . . . . . . . . . . . . 195
process conditions. . . . . . . . . . . . . . . . . . . 196
process temperature limits . . . . . . . . . . . . 194
process-wetted materials . . . . . . . . . . . . . 196
safe working pressure . . . . . . . . . . . . . . . . 195
service . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
upper range limit . . . . . . . . . . . . . . . . . . . . 194
Specifications and Reference Data
Functional Specifications
Output Signals . . . . . . . . . . . . . . . . . . . . . . 181
Output Testing . . . . . . . . . . . . . . . . . . . . . 182
Weight
Model 8705/8707 . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Diagrams
Brooks Model 5000 . . . . . . . . . . . . . . . . . . . . . . . .
Endress and Hauser Models . . . . . . . . . . . . . . . . .
Fisher and Porter Model 10D1418 . . . . . . . . . . . .
Foxboro Series 1800 . . . . . . . . . . . . . . . . . . . . . . .
Generic Flowtube . . . . . . . . . . . . . . . . . . . . . . . . .
Kent Flowtubes . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kent Veriflux VTC . . . . . . . . . . . . . . . . . . . . . . . . .
Krohne Flowtubes . . . . . . . . . . . . . . . . . . . . . . . . .
Taylor Series 1100 . . . . . . . . . . . . . . . . . . . . . . . .
Yamatake Honeywell Flowtubes . . . . . . . . . . . . .
Yokogawa Flowtubes . . . . . . . . . . . . . . . . . . . . . .
193
243
242
246
252
263
257
256
258
259
261
262
T
Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Temperature
Model 8705/8707 . . . . . . . . . . . . . . . . . . . . .188, 189
Model 8711 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
U
Upper Range Value (URV) . . . . . . . . . . . . . . . . . . . . . . . . 34
266
Operation and Maintenance
Reference Manual
00809-0100-4444, Rev AD
August 2015
Global Headquarters
Emerson Process Management
6021 Innovation Blvd.
Shakopee, MN 55379, USA
+1 800 522 6277 or +1 303 527 5200
+1 303 530 8459
[email protected]
North America Regional Office
Emerson Process Management
7070 Winchester Circle
Boulder, CO 80301 USA
+1 800 522 6277 or +1 303 527 5200
+1 303 530 8459
[email protected]
Latin America Regional Office
Emerson Process Management
Multipark Office Center
Turrubares Building, 3rd & 4th floor
Guachipelin de Escazu, Costa Rica
+1 506 2505-6962
+1 954 846 5121
[email protected]
Europe Regional Office
Emerson Process Management Flow B.V.
Neonstraat 1
6718 WX Ede
The Netherlands
+31 (0) 318 495555
+31 (0) 318 495556
[email protected]
Asia Pacific Regional Office
Emerson Process Management Asia Pacific Pte Ltd
1 Pandan Crescent
Singapore 128461
+65 6777 8211
+65 6777 0947
[email protected]
Middle East and Africa Regional Office
Emerson Process Management
Emerson FZE P.O. Box 17033,
Jebel Ali Free Zone - South 2
Dubai, United Arab Emirates
+971 4 8118100
+971 4 8865465
[email protected]
Standard Terms and Conditions of Sale can be found at:
www.rosemount.com\terms_of_sale.
The Emerson logo is a trademark and service mark of Emerson Electric Co.
Rosemount and Rosemount logotype are registered trademarks of Rosemount Inc.
All other marks are the property of their respective owners.
© 2015 Rosemount Inc. All rights reserved.
">