Owner`s Manual & Safety Instructions

Add to my manuals
12 Pages

advertisement

Owner`s Manual & Safety Instructions | Manualzz

Owner’s Manual & Safety Instructions

Save This Manual

Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

REV 15f

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.

Copyright © 2015 by Harbor Freight Tools ® . All rights reserved.

No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Table of contents

Safety ......................................................... 2

Installation .................................................. 4

Specifications ............................................. 4

Operation .................................................... 8

Maintenance ............................................... 8

Parts List and Diagram .............................. 10

Warranty .................................................... 12

WARNING SyMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMpORTANT SAFETy INFORMATION

General Safety Warnings

WARNING Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

1. Work area safety a. Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b. Keep children and bystanders away from an operating regulator.

2. personal safety a. Stay alert, watch what you are doing and use common sense when operating this regulator. Do not use this regulator while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating a regulator may result in serious personal injury.

Page 2 For technical questions, please call 1-888-866-5797.

Item 68247

b. Use personal protective equipment.

Always wear ANSI-approved eye protection during setup and use.

3. Regulator use and care a. Store an idle regulator out of the reach of children and do not allow persons unfamiliar with the regulator

or these instructions to operate it. b. Maintain the regulator. Keep the regulator clean for better and safer performance.

Follow instructions for lubricating and changing accessories. Keep dry, clean and free from oil and grease. check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the regulator’s operation. If damaged, have

the regulator repaired before use. c. Use the regulator in accordance with these instructions, taking into account the working

conditions and the work to be performed. Use of the regulator for operations different from those intended could result in a hazardous situation.

4. Service a. Have your regulator serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the regulator is maintained.

Air Regulator Safety Warnings

1. Risk of bursting - do not adjust regulator higher than marked maximum pressure of attachment.

2. Risk of injury - do not direct air stream at people or animals.

3. Do not use to supply breathing air.

4. Keep regulator well-ventilated.

Do not cover regulator during use.

5. Drain Air Filter daily and after use.

Internal rust causes tank failure and explosion.

6. Do not remove the valve cover or adjust internal components.

7. Do not use the air hose to move the regulator.

8. The use of accessories or attachments not recommended by the manufacturer may result in a risk of injury to persons.

9. All air line components, including hoses, pipe, connectors, filters, etc., must be rated for a minimum working pressure of 160 PSI, or 150% of the maximum system pressure, whichever is greater.

10. Industrial applications must follow OSHA guidelines.

11. Maintain labels and nameplates on the regulator. These carry important safety information. If unreadable or missing, contact

Harbor Freight Tools for a replacement.

12. This product is not a toy.

Keep it out of reach of children.

13. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.

14. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health

& Safety Code § 25249.5, et seq.)

15. WARNING: This product contains di (2-ethylhexyl) phthalate (DEHP), a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health

& Safety Code § 25249.5, et seq.)

SAVE THESE INSTRUcTIONS.

Item 68247 For technical questions, please call 1-888-866-5797.

Page 3

Specifications

Operating Pressure

Air Inlet and Outlet Size

Features

Filter

0 -160 PSI

Inlet: 1/2” -14 NPT (female thread)

Outlet: 1/4”-18 NPT (male thread)

Replaceable air filter element

40 micron

Installation

Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.

Note: This air tool may be shipped with protective plugs covering the air ports. Remove these plugs before set up.

TO pREVENT SERIOUS INJURy FROM EXpLOSION:

Use only clean, dry, regulated, compressed air to power this tool.

Do not use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool.

Functions

Air Inlet port

Regulator Handle

Regulator

Air Valve

Tank

Page 4

Gauge

For technical questions, please call 1-888-866-5797.

Drain plug

Item 68247

Installation

3B 1c

Figure A

1. Thread the Regulator Handle into the Air Regulator only a couple of turns. Do not tighten it.

Tightening it will set the regulator to high pressure, possibly causing property damage when first connecting the air supply.

2. Incorporate an in-line shutoff valve, and quick coupler for best service, as shown on

Figure B on page 6 and Figure C on page 7.

An in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured.

The shutoff valve should be a ball valve because it can be closed quickly.

Air connection Setup

1. Connect the regulator valve, an inline shut off valve and a 1/4″ NPT air hose to the Compressor’s

Quick Coupler. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working.

Note: An in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured. The shutoff valve should be a ball valve because it can be closed quickly.

Note: Wrap all threaded connectors before connecting them with pipe thread seal tape (PTFE) to prevent leaking.

3. Attach an air hose to the compressor’s air outlet.

Connect the air hose to the air inlet of the unit.

Note: Air flow, and therefore tool performance, can be hindered by undersized air supply components.

The air hose must be long enough to reach the work area with enough extra length to allow free movement while working.

4. Check that the regulator handle is loose.

5. Close the in-line shutoff valve between the compressor and the tool.

6. Turn on the air compressor according to the manufacturer’s directions and allow it to build up pressure until it cycles off.

7. Inspect the air connections for leaks.

Repair any leaks found.

2. Depending on the tool that will be used with this regulator, incorporate additional components, such as an in-line oiler, a filter, or a dryer (all sold separately), as shown on

Figure B on page 6 and Figure C on page 7.

Consult air tool’s manual for needed accessories.

Item 68247 For technical questions, please call 1-888-866-5797.

Page 5

Lubricated Tools Non-lubricated Tools

Page 6 For technical questions, please call 1-888-866-5797.

Item 68247

Lubricated Tools

Item 68247 For technical questions, please call 1-888-866-5797.

Page 7

Operating Instructions

Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Regulator Area Set Up

1. Designate a work area that is clean and well-lit.

The work area must not allow access by children or pets to prevent injury.

2. Locate the Regulator on a flat level surface to ensure proper pump lubrication and to prevent damage to the unit. Keep at least 12″ of space around the unit to allow air circulation.

General Operation

3. Route the power cord from the regulator to the grounded wall outlet, along a safe path without creating a tripping hazard or exposing the power cord to possible damage.

Note: At the beginning of the day’s first use of the

Air Regulator, check for air leaks by applying soapy water to connections while the Air Regulator is pumping and after pressure cut-out. Look for air bubbles. If air bubbles are present at connections, tighten connections.

Do not use the Air Regulator unless all connections are air tight, the extra air leaking out will cause the regulator to operate too often, increasing wear on the regulator.

WARNING! TO pREVENT SERIOUS

INJURy AND DEATH FROM

EXpLOSION:

Do not exceed 160 pSI

1. Adjust the Regulator Knob (1C) so that the air output is enough to properly power the tool, but the output will not exceed the tool’s maximum air pressure at any time. Turn the knob clockwise to increase the pressure and counter-clockwise to decrease pressure. Adjust the pressure gradually, while checking the air output gauge (6B) to set the pressure.

2. Make sure the air tool’s throttle or switch is in the off position. Connect the air tool to the air hose.

3. Open the in-line Shutoff Valve.

4. Use the air tool as needed.

5. After the job is complete, turn the compressor’s Power Switch OFF.

6. Disconnect the Air Regulator.

7. Close the in-line Shutoff Valve.

8. Bleed air from the tool then disconnect the tool.

9. Drain the Air Filter/Regulator of water daily. With the unit under pressure, open the Drain Plug (14A) to expel any accumulated moisture from the Air Filter.

10. Clean, then store the Air Regulator indoors.

Maintenance and Servicing

procedures not specifically explained in this manual must be performed only by a qualified technician.

TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION:

Turn the power Switch “OFF” and unplug the Regulator from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.

TO pREVENT SERIOUS INJURy FROM REGULATOR FAILURE:

Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.

Page 8 For technical questions, please call 1-888-866-5797.

Item 68247

cleaning, Maintenance, and Lubrication

1. BEFORE EAcH USE, inspect the general condition of the air regulator. Check for:

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts,

• damaged electrical wiring, and

• any other condition that may affect its safe operation.

2. AFTER USE, wipe external surfaces of the regulator with a clean cloth.

3. WARNING! If the supply cord of this regulator is damaged, it must be replaced only by a qualified service technician.

Maintenance Schedule

Following are general guidelines for maintenance checks of the Air Regulator.

Note: The environment in which the regulator is used, and the frequency of use will affect how often you will need to check the Air Regulator components and perform maintenance procedures.

Daily: a. Make sure all nuts and bolts are tight.

b. Drain moisture from air tank.

c. Check for abnormal noise or vibration.

d. Check for air leaks.

* e. Wipe off any oil or dirt from the regulator.

**

Weekly: a. Inspect Air Filter.

Quarterly (every 3 months): a. Tool Disassembly, Cleaning, and Inspection:

Have the internal mechanism cleaned, inspected, and lubricated by a qualified technician.

* To check for air leaks, apply soapy water to joints while the Air Regulator is pressurized. Look for air bubbles.

** To clean the regulator surface, wipe with a damp cloth, using a mild detergent or mild solvent.

Air Filter Maintenance

Check the Air Filter weekly to see if it needs replacement.

Replace the filter more often if regulator is used in dirty environments.

3. Periodically remove the Filter (6A), rinse it out with water and put it back in.

4. To access the air filter: a. Secure the Top Nut (1A) in a vise.

b. Loosen and remove the Bottom Nut (13A).

c. Pull off the Housing (7A), exposing the Filter Assembly. d. Disassemble the Filter Assembly. Keep track of assembly order. (Housing is not shown.)

See Figure D.

5. Remove the Filter.

6. Check that the Large Plate and Cup are in place, and replace with a new Filter.

7. Reassemble Filter Assembly according to assembly order described in Figure D.

Note: Retaining Ring should slide on tightly against the Filter Washer and Filter. If it is loose, the Filter will not function.

8. Replace the Housing.

Note: Rubber Seals on Nuts and Housing must be in good condition before reassembly.

9. Thread Bottom Nut back on to Stud. Tighten.

Top plug

Filter

Filter Washer

Figure D

Large plate cup

Retaining Ring

Bottom plug

Item 68247 For technical questions, please call 1-888-866-5797.

Page 9

parts List and Diagram pLEASE READ THE FOLLOWING cAREFULLy

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

parts List and Diagram A

part Description

1A Top Nut

2A Filter Cap

3A Gasket

4A Large Plate

5A Cup

6A Filter

7A Housing

8A Filter Washer

9A Retaining Ring

10A Stud

11A Gasket

12A Filter Base

13A Bottom Nut

14A Drain Plug

1A

7A

8A

9A

10A

2A

3A

4A

5A

6A

11A

12A

13A

14A

Air inlet port

Record product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

Page 10 For technical questions, please call 1-888-866-5797.

Item 68247

parts List and Diagram B

part

1B Nipple

Description

2B Elbow

3B Air Regulator

4B Plug

5B Air Valve

6B Gauge

4B

2B

3B

6B

1B

5B

parts List and Diagram c

part Description

1C Regulator Handle

2C Housing Cap

3C Spring Button

4C Spring

5C Spring Seat

6C O-Ring

7C Steel Plate

8C Brass Nut

9C O-Ring

10C Pin

11C Spring

12C Body

13C Screen

Item 68247 For technical questions, please call 1-888-866-5797.

1c

2c

3c

4c

5c

6c

7c

8c

9c

10c

11c

12c

13c

Page 11

Limited 90 Day Warranty

Harbor Freight ToolsHarbor Freight ToolsHarbor Freight ToolsHarbor Freight ToolsHarbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • pO Box 6009 • camarillo, cA 93011 • 1-888-866-5797

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement