Sharp R-216FS Service manual
R-216FS
SUPPLEMENTAL SERVICE MANUAL
S9214R216FPST
MICROWAVE OVEN
MODEL
R-216FS
In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe,
possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..)
This is a supplemental Service Manual for Model R-216FS. This model is quite similar to base
model R-214FW. Use this supplemental manual together with the Base Model Service Manual
(Refer No. is S3208R220FPW/) for complete operation, service information, etc..
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ...................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................ 1
MICROWAVE MEASUREMENT PROCEDURE ................................................................................................... 2
FOREWORD AND WARNING ............................................................................................................................... 3
PRODUCT SPECIFICATIONS .............................................................................................................................. 4
OVEN DIAGRAM ................................................................................................................................................... 5
OVEN SCHEMATIC ............................................................................................................................................... 6
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE .................................................................. 7
PARTS LIST ........................................................................................................................................................ 10
PACKING AND ACCESSORIES ......................................................................................................................... 11
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
SHARP CORPORATION
15
R-216FS
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures described
in this manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS
CORPORATION immediately @1-800-237-4277.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's
Center for Devices and Radiological Health immediately.
Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit
found with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use
the unit until the oven has been brought into compliance.
16
R-216FS
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
When the testing is completed,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
Before Servicing
1. Disconnect the power supply cord
remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
, and then
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for 60
seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an
insulated screwdriver.
After repairing
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
Whenever troubleshooting is performed the power supply
must be disconnected. It may, in some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that the leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out Before Servicing procedure and reexamine the connections to the component being tested.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and microwave leakage test should be carried out.
1
R-216FS
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches: Primary interlock relay and door sensing switch shall prevent microwave radiation emission
in excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission
in excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard
for microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5˚C (68˚F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.)
and made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed,
replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on
the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the secondary interlock switch and the primary interlock relay do turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
R-216FS
SERVICE MANUAL
MICROWAVE OVEN
R-216FS
FOREWORD
This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service
Information for the SHARP MICROWAVE OVENS, R-216FS.
The model R-216FS is quite similar to base model R-214FW (Refer No. is S3208R220FPW/).
It is recommended that service personnel carefully study the entire text of this manual and the base model's manual so
that they will be qualified to render satisfactory customer service.
Check the interlock switches and the door seal carefully. Special attention should be given to avoid electrical shock and
microwave radiation hazard.
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
Servicing and repair work must be carried out only by trained service personnel.
DANGER
Certain initial parts are intentionally not grounded and present a risk of electrical shock only during servicing.
Service personnel - Do not contact the following parts while the appliance is energized;
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage
Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more than 250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “∆” on parts list may cause undue microwave exposure, by themselves, or when they are
damaged, loosened or removed.
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH,
NEW JERSEY 07430-2135
3
R-216FS
PRODUCT DESCRIPTION
SPECIFICATIONS
ITEM
DESCRIPTION
Power Requirements
120 Volts
60 Hertz
Single phase, 3 wire grounded
Power Consumption
1200W / Approx. 10.3 Amperes
Power Output
800 W nominal of RF microwave energy (IEC Test procedure)
Operating frequency 2450 MHz
Case Dimensions
Width 18-1/8"
Height 10-7/8"
Depth
14"
Cooking Cavity Dimensions
(0.8 Cubic feet)
Width 12-5/8"
Height 7-7/8"
Depth 13-1/4"
Control Complement
Touch Control System
Clock (1:00 - 12:59)
Timer (0 - 99 minutes 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI ................................... Full power throughout the cooking time
P-90 .................................................... approx. 90% of FULL Power
P-80 .................................................... approx. 80% of FULL Power
P-70 .................................................... approx. 70% of FULL Power
P-60 .................................................... approx. 60% of FULL Power
P-50 .................................................... approx. 50% of FULL Power
P-40 .................................................... approx. 40% of FULL Power
P-30 .................................................... approx. 30% of FULL Power
P-20 .................................................... approx. 20% of FULL Power
P-10 .................................................... approx. 10% of FULL Power
P-0 ...................................... No power throughout the cooking time
POPCORN pad, MINUTE PLUS pad
REHEAT pad, COOK pad, DEFROST pad
Number selection pads
TIMER / CLOCK pad
POWER LEVEL pad
START pad
STOP/CLEAR pad
Oven Cavity Light
Yes
Safety Standard
UL Listed.
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
4
R-216FS
OVEN DIAGRAM
5
1 Door open button
Push to open door.
2 Oven door with see-through window
3 Safety door latches
The oven will not operate unless the door is
securely closed.
4 Door hinges
5 Door seals and sealing surfaces
6 Turntable motor shaft
7 Removable turntable support
Carefully place the turntable support in the center
of the oven floor.
8 Removable turntable
Place the turntable securely on the turntable
support. The turntable will rotate clockwise or
counterclockwise. Only remove for cleaning.
9 Ventilation openings (Rear)
10 Oven light
It will light when oven is operating.
11 Waveguide cover: DO NOT REMOVE.
12 Auto-Touch control panel
13 Time display: 99 minutes, 99 seconds
10
9
13
8
12
4
7
1
3 2
6
11
TOUCH CONTROL PANEL
NOTE:
Some one-touch cooking features such as "MINUTE PLUS" are
disabled after three minutes when the oven is not in use. These
features are automatically enabled when the door is opened and
closed or the STOP/ CLEAR pad is pressed.
5
R-216FS
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED
2. CLOCK APPEARS ON DISPLAY
C/T FUSE
NOTE: "
TEMPERATURE
FUSE (OVEN)
N.O.
POWER
TRANSFORMER
COM.
(RY-2)
(RY-1)
A3
" indicates components with potentials above 250V.
PRIMARY
INTERLOCK
RELAY
CAPACITOR
0.82µF
AC2100V
CONTROL UNIT
A1
B2
B1
GRN
120V AC
60 Hz
DOOR
SENSING
SWITCH
TTM
OL
OVEN
LAMP
TURNTABLE
MOTOR
MONITOR
SWITCH
FM
RECTIFIER
MAGNETRON
FAN
MOTOR
SECONDARY
INTERLOCK
SWITCH
Figure O-1. Oven Schematic-Off Condition
6
R-216FS
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
WARNING AGAINST HIGH VOLTAGE:
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may
result in severe, possibly fatal, electric shock.
(Example)
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
WARNING:
Avoid possible exposure to microwave energy. Please follow the instructions below before
operating the oven.
1. Disconnect the power supply cord.
2. Make sure that a definite” click” can be heard when the
microwave oven door is unlatched. (Hold the door in a
closed position with one hand, then push the door open
button with the other, this causes the latch leads to rise,
it is then possible to hear a “click’ as the door switches
operate.)
3. Visually check the door and cavity face plate for damage
(dents, cracks, signs of arcing etc.).
1.
2.
3.
4.
5.
6.
Door does not close firmly.
Door hinge, support or latch hook is damaged.
The door gasket or seal is damaged.
The door is bent or warped.
There are defective parts in the door interlock system.
There are defective parts in the microwave generating
and transmission assembly.
7. There is visible damage to the oven.
Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
WARNING FOR WIRING
To prevent an electric shock, take the following precautions.
1. Before wiring,
1) Disconnect the power supply cord.
2) Open the door block it open.
3) Discharge the high voltage capacitor and wait for 60
seconds.
2. Don’t let the wire leads touch to the following parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, High voltage transformer
and Oven cavity.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector until its pin is locked
and make sure that the wire leads do not come off even
if the wire leads are pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS’, when carrying out any of
the following removal procedures:
CONTROL PANEL ASSEMBLY REMOVAL
1.
2.
3.
4.
5.
Disconnect the power supply cord and remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the leads from the control unit.
Remove the one (1) screw holding the control panel
decoration to the oven cavity front plate.
6. Remove the one (1) screw holding the control panel to
the front plate of the oven cavity.
7. Now, the control panel assembly is free.
7
R-216FS
GRAPHIC SHEET AND MEMBRANE SWITCH REPLACEMENT
Removal
1. Disconnect the power supply cord and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the control panel assembly, referring to chapter
of CONTROL PANEL ASSEMBLY REMOVAL.
5. Remove the three (3) screws holding the control unit to
the control panel frame. And remove the control unit.
6. Remove the rubber connector from the long slit on the
control panel frame.
7. Tear away the graphic sheet from the control panel
frame.
8. Tear away the membrane switch from the control panel
frame.
Installation
1. Remove remaining adhesive on the control panel frame
surfaces with a soft cloth soaked in alcohol.
2. Tear the backing paper from the new membrane switch.
3. Insert the ribbon cable of the membrane switch into the slit
of the control panel frame.
4. Adjust the upper edge and right edge of the membrane
switch to the small depression on the surface of the
control panel frame.
5. Attach the membrane switch to the control panel frame by
rubbing with a soft cloth not to scratch.
6. Tear the backing paper from the new graphic sheet.
7. Adjust the upper edge and right edge of the graphic sheet
to the large depression on the surface of the control
panel frame.
8. Attach the graphic sheet to the control panel frame by
rubbing with a soft cloth not to scratch.
9. Tear the small backing paper from the ribbon cable of the
membrane switch.
10. Insert the two (2) holes of the ribbon cable into the two
(2) pins of the control panel frame (rear side).
11. Attach the ribbon cable to the control panel frame rear
side.
12. Place the edge of the membrane switch’s ribbon cable
on the lower portion of the liquid crystal display.
13. Insert the rubber connector into the long slit on the
control panel frame.
14. Reinstall the control unit to the control panel frame with
the three (3) screws.
NOTE:
Do not contact the conductor portion of the ribbon
cable (edge) and the rubber connector directly with
your fingers. This is to avoid oxidized.
Control panel frame
Small backing
paper
Slit
Ribbon
cable
Small
depression
Graphic sheet
Membrane
switch
Liquid crystal
display
Control panel frame
(Rear side)
Long slit
Conductor portions
Pin
Ribbon cable
of membrane
switch
Rubber connector
Figure C-2. Graphic Sheet and Membrane Switch
Replacement
DOOR REPLACEMENT
9
8
Choke Cover
REMOVAL
1. Disconnect the power supply cord.
2. Open the door slightly.
3. Insert a putty knife (thickness of about 0.5mm) into the
gap between the choke cover and corner portion of door
panel as shown in Figure C-5 to free engaging parts.
4. Pry the choke cover by inserting a putty knife in order
shown in figure C-5.
5. Release choke cover from door panel.
6. Now choke cover is free.
NOTE: When carrying out any repair to the door, do not
bend or warp the slit choke (tabs on the door
panel assembly) to prevent microwave leakage.
10
7
11
6
1
5
2
4
3
Putty Knife
Door Frame
Figure C-5. Door Disassembly
7. Release two (2) pins of door panel from two (2) holes of
upper and lower oven hinges by lifting up.
8. Now, door panel is free from oven cavity.
8
R-216FS
9. Release door panel from ten (10) tabs of door frame and
remove door frame by sliding the door panel downward.
10.Now, door panel with sealer film is free.
11.Tear sealer film from door panel.
12.Now, door panel is free.
13.Slide latch head upward and remove it from door frame
with releasing latch spring from door frame and latch
head.
14.Now, latch head and latch spring are free.
15.Remove door screen from door frame.
16.Now, door screen is free.
17.Unholed each six (6) tab of the door decoration upper
and lower by using a pair of needle-nose pliers. And
remove the door decoration upper and lower from the
door frame. Now, the door frame is loose.
Note:
The door on a microwave oven is designed to act as
an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
cycle. This function does not require that door be airtight, moisture (condensation)-tight or light-tight.
Therefore, occasional appearance of moisture, light
or sensing of gentle warm air movement around
oven door is not abnormal and do not of themselves,
indicate a leakage of microwave energy from oven
cavity.
Pin
RE-INSTALL
1. Insert each six (6) tab of the door decoration upper and
lower into each slit of the door frame and bent the tabs
by using a pair of needle-nose pliers.
2. Re-install door screen to door frame.
3. Re-install latch spring to the head. Re-install latch spring
to the door frame. Re-install latch head to the door frame.
4. Re-install door panel to door frame by fitting ten (10) tabs
of door frame to ten (10) holes of door panel.
5. Put sealer film on door panel. Refer to "Sealer Film" and
figure C-7, on how to handle the new film.
6. Catch two (2) pins of door panel on two (2) hole of upper
and lower oven hinges.
7. Re-install choke cover to door panel by pushing.
Note: After any service to the door;
(A) Make sure that door sensing switch, secondary
interlock switch and monitor switch are operating
properly. (Refer to chapter "Test Procedures".).
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
Upper Oven Hinge
Slit Choke
Door
Panel
Lower Oven
Hinge
Choke Cover
Lower
Oven
Pin Hinge
Figure C-6. Door Replacement
SEALER FILM
Installation
1. Put the adhesive tape on the backing film of the sealer
film as shown in Fig. C-7.
2. Tear the backing film by pulling the adhesive tape.
3. Put the pasted side of the sealer film on the door panel
After any service, make sure of the following :
1. Door latch heads smoothly catch latch hook through
latch holes and that latch head goes through center of
latch hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Check for microwave leakage around door with an
approved microwave survey meter. (Refer to Microwave
Measurement Procedure.)
Sealer film
Backing film
Adhesive tape
Figure C-7. Sealer film
9
R-216FS
PARTS LIST
Note: The parts marked “∆” may cause undue microwave exposure.
The parts marked “*” are used in voltage more than 250V.
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AF
AH
AS
AS
AN
AP
AV
AN
AP
AS
AX
AN
AV
AU
BE
BF
BL
AL
AW
AS
AK
BF
--
1
2
1
BD
AC
AG
1
1
1
1
1
1
1
1
1
1
1
1
3
AZ
AX
AQ
AL
AT
AS
AH
AZ
AB
BF
AE
AQ
AA
1
1
1
1
1
1
1
1
2
1
1
1
AM
AF
AK
AR
-AK
AG
AM
AF
AC
AB
AC
1
1
1
1
1
1
1
1
BC
AY
AW
AU
AT
AS
AF
AC
ELECTRIC PARTS
*
*
*
*
*
∆*
∆*
∆*
*
*
1- 1
1- 1
1- 2
1- 3
1- 3
1- 3
1- 3
1- 4
1- 4
1- 5
1- 5
1- 5
1- 6
1- 6
1- 7
1- 7
1- 7
1- 8
1- 9
1- 9
1-10
1-11
1-11
QSW-MA085WRE0
QSW-MA137WRE0
FFS-BA030WRKZ
FACCDA089WREZ
FACCDA086WREZ
FACCDA081WRE0
FACCDA082WRE0
FH-DZA102WRKZ
FH-DZA088WRK0
RC-PZA041WRE0
RC-QZA307WRZZ
RC-QZA308WRZZ
RMOTEA383WRE0
RMOTEA355WRE0
RV-MZA226WRE0
RV-MZA261WRE0
RV-MZA306WRZZ
RLMPTA082WRZZ
RMOTDA186WRE0
RMOTDA211WRE0
QFS-TA038WRE0
RTRN-A661WRZZ
RTRN-A659WRZZ
Secondary interlock switch/ Door sensing switch
Secondary interlock switch/ Door sensing switch (Interchangeable)
C/T fuse (120˚C/15A) and monitor switch assembly (AM51620C53Y1)
Power supply cord
Power supply cord (Interchangeable)
Power supply cord (Interchangeable)
Power supply cord (Interchangeable)
High voltage rectifier assy
High voltage rectifier assy (Interchangeable)
High voltage capacitor
High voltage capacitor (Interchangeable)
High voltage capacitor (Interchangeable)
Fan motor
Fan motor (Interchangeable)
Magnetron
Magnetron (Interchangeable)
Magnetron (Interchangeable)
Oven lamp
Turntable motor
Turntable motor (Interchangeable)
Temperature fuse 120˚C (Oven)
Power transformer
Power transformer (Interchangeable) for production use
2- 1
2- 2
2- 3
GCABUA864WRPZ
GLEGPA074WRE0
PCUSUA605WRPZ
Outer case cabinet
Foot
Cushion
CABINET PARTS
CONTROL PANEL PARTS
3333333333333-
1
1-1
1-2
1-3
1-4
2
2-1
2-2
3
4
5
6
7
FPNLCB671WRKZ
PSHEPA855WRZZ
QSW-KA022DRZZ
GMADIA118WRRZ
HDECQA236WRPZ
FBTN-A146WRKZ
JBTN-B187WRFZ
HDECQA239WRPZ
MSPRCA050WRE0
DPWBFC240WRUZ
QCNC-A014WRZZ
RLCDSA105DRZZ
XEPSD30P08XS0
Control panel frame with key unit
Graphic sheet
Membrane switch
Display window
Control panel decoration
Open button assembly
Open button
Button decoration
Open button spring
Control unit
Rubber connector
Liquid crystal display
Screw; 3mm x 8mm
PHOK-A122WRFZ
LBNDKA038WRP0
NFANJA029WRE0
PDUC-A801WRWZ
*************
GCOVHA425WRPZ
MLEVPA241WRFZ
PCOVPA276WRE0
PCUSUA237WRP0
PPACGA176WREZ
PCUSUA278WRP0
PCUSGA568WREZ
Latch hook
Capacitor holder
Fan blade
Fan duct
Oven cavity (Not replaceable part)
Turntable motor cover
Switch lever
Waveguide cover
Cushion
TTM packing
Cushion
Cushion
OVENPARTS
∆ 4- 1
∆
∆
∆
∆
∆
4- 2
4- 3
4- 4
4- 5
4- 6
4- 7
4- 8
4- 9
4-10
4-11
4-12
DOORPARTS
55555555-
1
2
2-1
2-2
2-3
3
4
5
FDORFA348WRTZ
FWAKPA373WRKZ
GWAKPA871WRFZ
HDECQA237WRRZ
HDECQA238WRRZ
HPNL-A785WRRZ
LSTPPA205WRFZ
MSPRTA187WRE0
Door panel assembly
Door frame assembly
Door frame
Door decoration U
Door decoration L
Door screen
Latch head
Spring
10
R-216FS
REF. NO.
PART NO.
DESCRIPTION
5- 6
5- 7
PSHEPA782WREZ
GCOVHA424WRFZ
Sealer film
Choke cover
666666-
1
2
3
4
5
6
NTNT-A094WRE0
FROLPA101WRKZ
TCAUAA271WRRZ
TCAUAA268WRRZ
TINSEA955WRRZ
FW-VZB837WREZ
Turntable
Turntable support
Monitor caution
DHHS caution label
Instruction book
Main wire harness
77777777777-
1
2
3
4
5
6
7
8
9
10
11
XHPSD40P08K00
XHTSD40P08RV0
LX-CZA070WRE0
LX-CZ0052WRE0
LX-EZA042WRE0
XHPSD30P06000
XHPSD40P08000
XHTSD40P12RV0
XOTSE40P08000
XOTSD40P08000
XCPSD40P06000
screw :
Screw :
Special
Special
Special
Screw :
Screw :
Screw :
Screw :
Screw :
Screw :
Q'TY
CODE
1
1
AG
AK
1
1
1
1
1
1
AN
AR
AF
AF
AM
AR
2
5
2
2
2
1
3
1
2
7
1
AC
AA
AC
AA
AB
AA
AA
AA
AA
AA
AA
MISCELLANEOUS
SCREWS,NUTS AND WASHERS
4 mm x 8 mm
4mm x 8mm
screw (Torx tamper pfoof screw)
screw
screw
3mm x 6mm
4mm x 8mm
4mm x 12mm
4mm x 8mm
4mm x 8mm
4mm x 6mm
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
Order Parts from the authorized SHARP parts Distributor for your area.
Defective parts requiring return should be returned as indicated in the Service Policy.
PACKING AND ACCESSORIES
TOP PAD ASSEMBLY
FPADBA454WRKZ
DOOR PROTECTION SHEET
SPADPA580WRE0
POLYETHYLENG BAG
SSAKHA014WRE0
6-5 INSTRUCTION BOOK
6-1 TURNTABLE TRAY
MICROWAVE OVEN
BOTTOM PAD ASSEMBLY
FPADBA455WRKZ
6-2 TURNRTABLE SUPPORT
INTO THE
OVEN CAVITY
Not replaceable items.
TRAY PAD ASSY
(CPADBA296WRKZ)
11
PACKING CASE
FPAK-A438WRKZ
R-216FS
2
1
4
3
7-10
OVEN AND CABINET PARTS
2-1
A
6
5
7-3
A
7-10
7-10
B
B
7-3
1-8
2-3
7-10
7-9
7-6
4-3
C
1-2
7-10
7-2
7-9
7-7
C
4-12
4-9
7-10
6-4
1-10
4-4
1-7
1-6
6-3
D
D
7-8
4-9
4-11
1-3
7-5
7-2
3-1-4
E
E
7-10
1-11
4-5
7-2
7-11
4-8
F
F
4-1
6-1
7-4
1-1
1-4
4-10
2-2
7-1
1-2
1-5
G
G
1-1
7-1
6-2
1-9
2-2
4-7
4-2
4-6
7-2
H
H
1
2
4
3
12
5
6
R-216FS
2
1
4
3
6
5
Before attaching Control unit to Control
panel, foil side of Control unit must be
cleaned by ethyl-alcohol.
CONTROL PANEL PARTS
3-1
A
A
3-1-4
3-7
3-1-3
3-5
3-1-1
B
3-4
3-6
B
DOOR PARTS
3-1-2
C
C
5-7
3-2
3-3
3-2-1
5-6
D
D
3-2-2
5-2
5-1
5-2-1
E
E
5-2-2
5-3
5-2-3
F
F
5-4
5-5
G
G
MISCELLANEOUS
6-6
H
H
Actual wire harness may be different from illustration.
1
2
4
3
13
5
6
R-216FS
COPYRIGHT © 2002 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in retrieval systems, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
2002SHARP CORP. (1S1.70E) Printed in U.S.A
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement