English - Dwyer Instruments, Inc.

English - Dwyer Instruments, Inc.
Bulletin E-57G
Series 1950G – Integral Explosion-Proof Pressure Switches
®
Specifications - Installation and Operating Instructions
Set Point
Adjustment Screw
External
Ground Screw
UL, CSA, FM Listed For
CL, I GR. A*, B, C, D - CL. II GR. E, F, G - CL. III
Directive 94/9/EC (ATEX) Compliant For
0518
II 2G Ex d IIB + H2 T6 Gb
EC-Type Certificate Number: KEMA 03ATEX2402 X
ATEX Standards:
EN 60079-0:2012 + A11:2013
EN 60079-1:2007
IECEx Certified for:
Ex d IIB + H2 T6 Gb (-40°C < Ta < +60°C)
IECEx Certificate of Conformity:
IECEx DEK 11.0092X
IECEx Standards:
IEC 60079-0:2011
IEC 60079-1:2007
1/2˝ Female NPT
Electrical Conduit
Connection
Vent Drain
Plug
Captive
Screw
The MODEL 1950G Explosion-Proof Switch combines the best features of the popular
Series 1900 Pressure Switch with a compact explosion-proof housing.
This unit is UL, CSA, FM listed for use in Class I, Groups A*, B, C, D, Class II, Groups
E, F, & G and Class III atmospheres and Directive 94/9/EC (ATEX) Compliant for
II 2G Ex d IIB + H2 T6 Gb. IECEx and KC certified Ex d IIB + H2 T6 Gb (-40°C
< Ta < + 60°C) units are available. It is also totally rain-tight for outdoor installations.
Six models allow set-points from 0.07 to 20 in w.c. (1.78 mm to 508.0 mm w.c.).
Easy access to the SPDT relay for electrical hook-up is provided by removing the top
plate of the aluminum housing. A captive screw allows the cover to swing aside while
remaining attached to the unit. Adjustment to the set point of the switch can be made
without disassembly of the housing. The unit is very compact, about half the weight
and bulk of equivalent conventional explosion-proof switches.
Attention: Units with the “NA” suffix are not Directive 94/9/EC (ATEX) compliant.
These units are not intended for use in potentially explosive atmospheres in the EU.
These units may be CE marked for other Directives of the EU.
SPECIFICATIONS
Service: Air and compatible combustible gases.
Wetted Materials: Contact Factory.
Temperature Limits: 0 to 140°F (-17 to 60°C). Note: Set point drift may occur with
ambient temperature changes.
Pressure Limits: 45 in w.c. (11.2 kPa) continuous; 10 psig (68.95 kPa) surge.
Enclosure Rating: IP54, NEMA 3, 7 and 9.
Switch Type: 1 Form C relay (SPDT).
Electrical Rating: 10A, 120/240 VAC, 28 VDC. Resistive 50mA, 125 VDC.
Power Requirements: 24 VDC ±10%. 120 or 240 VAC ±10% optional.
Electrical Connections: Internal Terminal Block.
Process Connections: 1/8˝ female NPT.
Mounting Orientation: Diaphragm in vertical position. Consult factory for other
position orientations.
Set Point Adjustment: Screw type on top of housing.
Weight: 2 lb, 15.7 oz (1.35 kg).
MODEL 1950G SWITCHES:
OPERATING RANGES AND DEADBANDS
Approximate Dead
Band
Operating
To order Specify Range
At Min.
At Max.
Model Number* in w. c.
Set Point Set Point
1950G-00-B-__
0.07 to 0.15 0.04
0.06
1950G-0-B-__
0.15 to 0.5
0.06
0.11
1950G-1-B-__
0.4 to 1.6
0.11
0.29
1950G-5-B-__
1.4 to 5.5
0.4
0.9
1950G-10-B-__
3.0 to 11.0
0.9
1.8
1950G-20-B-__
4.0 to 20.0
1.2
3.0
*Specify either 24 for 24 VDC, 120 for 120 VAC or 240
for 240 VAC when ordering. Example: 1950G-00-B-120
*Add “NA” suffix for models with UL, CSA and FM
approvals only. Example: 1950G-00-B-120-NA
*GR. A is
Only.
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.
Phone: 219/879-8000
www.dwyer-inst.com
Fax: 219/872-9057
e-mail: [email protected]
RANGE
ADJUSTMENT
SCREW
17/64˝ DIA. MTG. HOLES (2)
3-1/2
[88.90]
EXTERNAL GROUND
4-7/8
[123.8]
5-7/16
[138.1]
1/8˝ NPT HIGH
PRESSURE PORT
1-11/16
[42.86]
1/8˝ NPT
LOW PRESSURE
PORT
Fig. A
CAPTIVE
SCREW
1/2˝ NPT
ELECTRICAL
CONDUIT
CONNECTION
VENT
DRAIN
PLUG
1-17/32
[38.89]
13/32
[10.312]
+ -
1950G Switch Outline Dimensions
Fig. B
INSTALLATION
1. Select a location free from excess vibration and corrosive atmospheres where
temperatures will be within the limits noted under Physical Data on page 1. Switch
may be installed outdoors or in areas where the hazard of explosion exists. See page
1 for specific types of hazardous service.
For units supplied with both internal and external bonding terminals, the ground screw
inside the housing must be used to ground the control. The internal bonding screw is
for supplementary bonding when allowed or required by local code. When external
bonding conductor is required, conductor must be wrapped a minimum of 180° about
the external bonding screw. See below.
2. Mount standard switches with the diaphragm in a vertical plane and with switch
lettering and nameplate in an upright position. Some switches are position sensitive
and may not reset properly unless they are mounted with the diaphragm vertical.
LOCKWASHER
3. Connect switch to source of pressure, vacuum or differential pressure. Metal tubing
with 1/4˝ O.D. is recommended, but any tubing which will not restrict the air flow can be
used. Connect to the two 1/8˝ female NPT pressure ports as noted below.
A. Differential pressures - connect pipes or tubes from source of greater pressure to
high pressure port marked HIGH PRESS, and from source of lower pressure to low pressure port marked LOW PRESS.
CLAMP PLATE
CLAMP
B. Pressure only (above atmospheric pressure) - connect tube from source of pressure to high pressure port. The low pressure port is left open to atmosphere.
C. Vacuum only (below atmospheric pressure) - connect tube from source of vacuum
to low pressure port. The high pressure port is left open to atmosphere.
4. To make electrical connections, remove the three hex head screws from the
cover and after loosening the fourth captive screw, swing the cover aside. Electrical
connections to the standard single pole, double throw relay and AC supply voltage
connections to the unit, are provided by means of terminals marked “COM”, “NO”,
“NC”, “~” and “~” (See Fig. A). Electrical connections to the standard single pole,
double throw relay and DC supply voltage connections to the unit, are provided by
means of terminals marked “COM”, “NO”, “NC”, “+” and “-” (See Fig. B.). The normally
open contacts close and the normally closed contacts open when pressure increases
beyond the setpoint. Switch loads for standard models should not exceed the maximum
specified current ratings as stated on page 1. For ATEX, IECEx compliance, cables
and cable glands suitable for temperature of at least 95°C shall be used. The cable
entry device shall be of certified flameproof type, suitable for the conditions of use and
be correctly installed. Refer to Certificate No.: IECEx DEK 11.0092X for conditions of
safe use for IECEx Compliant units. Switch capabilities decrease with an increase in
ambient temperature, load inductance, or cycling rate.
CONDUCTOR
SCREW
FRONT VIEW DETAIL
SIDE VIEW DETAIL
ADJUSTMENT
To change setpoint:
A. Remove the plastic cap and turn the slotted Adjustment Screw at the top of the housing clockwise to raise the setpoint pressure and counter-clockwise to lower the setpoint. After calibration, replace the plastic cap and re-check the setpoint.
B. The recommended procedure for calibrating or checking calibration is to use a
“T” assembly with three rubber tubing leads, all as short as possible and the entire
assembly offering minimum flow restriction. Run one lead to the pressure switch,
another to a manometer of known accuracy and appropriate range, and apply pressure through the third tube. Make final approach to the setpoint very slowly. Note
that manometer and pressure switch will have different response times due to
different internal volumes, lengths of tubing, fluid drainage, etc. Be certain the switch
is checked in the position it will assume in use, (i.e. with diaphragm in a vertical
plane) and switch lettering and Dwyer nameplate in an upright position.
C. For highly critical applications check the setpoint adjustment and if necessary,
reset it as noted in step A.
MAINTENANCE
The moving parts of these switches need no maintenance or lubrication. The only
adjustment is that of the setpoint. Care should be taken to keep the switch reasonably
clean. Periodically the vent drain plug should be rotated then returned to its original
position. This will dislodge deposits which could accumulate in applications where
there is excessive condensation within the switch. Repairs to be conducted by Dwyer
Instruments, Inc. Cover bolts are Class 10.9 35 mm long.
©Copyright 2016 Dwyer Instruments, Inc.
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.
Printed in U.S.A. 1/16
FR# 28-440332-10 Rev.11
Phone: 219/879-8000
www.dwyer-inst.com
Fax: 219/872-9057
e-mail: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement