Helpful Hints
1) No sound:
The MUTE function has been inadvertently engaged.
Speakers have been improperly connected.
Effect Loop has been improperly connected.
2) AMP seems very sensitive on input signals:
The drive control is turned all the way up.
The active switch may need to be turned on.
3) DIR XLR hum:
Try switching the rear GND LIFT switch IN or OUT.
Check for noise from external effects or bad cabling.
4) POOR BASS FROM MULTIPLE ENCLOSURES:
Make sure the internal speaker wiring of each cabinet is correct for phase ( +/- ).
5) FOR MAXIMUM OUTPUT:
To get more output, use multiple speakers or enclosures. Every time you double your speakers, your acoustic output goes up by a factor of four.
Load the amplifier down to its lowest minimum impedance for maximum RMS power.
* If you are using less than 4 ohms, be sure to set the 2 OHM SWITCH to IN. If you go below the minimum load, your amp will shut off and go into the “protect” mode. To reset,
turn your amp off and connect the recommended load or set the 2 OHM SWITCH.
SPEAKON® cables are recommended for your BX700 because of their high current capacity. While standard 1/4” speaker cables will work, 12 GA SPEAKON® cables will allow higher
currents to pass through the cable to extract every watt from your amp.
The BX700 is a powerful amplifier. As with any amplifier, make sure your speakers are suitable for the available wattage. Driving speakers with too much wattage will cause them to
distort and eventually fail. If distorted sound is coming from the speakers, reduce the volume until the distortion stops.
This symbol is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol is
intended to alert the
user to the presence
of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The product should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or
polarization is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention
to cords at plugs.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
LIMITED WARRANTY
Your Carvin product is guaranteed against failure for 1 YEAR unless otherwise stated.
Carvin will service and supply all parts at no charge to the customer providing the unit
is under warranty. Shipping costs are the responsibility of the customer. CARVIN
DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF
THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes
no responsibility for horn drivers or speakers damaged by this unit. This warranty
does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow
instructions. This warranty is in lieu of all other warranties, expressed or implied. No
representative or person is authorized to represent or assume for Carvin any liability
in connection with the sale or servicing of Carvin products. CARVIN SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
MAINTAINING YOUR EQUIPMENT
Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel
of your unit can be wiped with a dry or slightly damp cloth in order to remove dust
and bring back the new look. As with all pro gear, avoid prolonged use in caustic
environments (salt air). When used in such an environment, be sure the amplifier is
adequately protected.
SERVICE
SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth
BLUE—Neutral
BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED
OR CUT MAIN PLUG INTO A POWER SOCKET.
In the USA go to www.carvinservice.com.
Outside the USA, contact your dealer or go to http://www.carvinworld.com for your
nearest service center. Include a written description of the problem with serial number
and date of purchase.
CARVIN ENGINEERING DATA
BX700 BASS AMPLIFIER
OPERATING MANUAL
MADE IN
USA
The BX Series Bass Amplifier Heads offer classic natural bass tone with unprecedented
tonal control and extended headroom. The BX700 delivers 300w at 8 ohms, 550w at 4ohms
and 700w at 2ohms, yet weighs under 6 pounds.
Four discrete Class A input stages produce the harmonic basis for the preamp right from
the input jack. It begins with a boutique flat response, then we add extensive tone control
allowing you to carve out your signature sound. Harmonic content increases as you turn up
the DRIVE control producing rich harmonics at maximum settings. The BX700 also features a
12AX7 preamp tube (bypassable) to add further warmth to your sound. The CLASS-D output
and lightweight switch-mode power supply use far less energy from the wall while producing
more power with less heat.
Light weight, solid design, bullet-proof construction and a list of indispensable features assure
the BX700 will be the heart of your rig for years to come.
• Discrete CLASS A input stages
• Preamp DRIVE and MASTER volume controls
• 2 mid sweep semi-parametric EQ, BASS and TREBLE
• Switchable 9-band Graphic EQ with front panel switch or by the optional FS22 footswitch
• Single knob COMPRESSOR
• Effect Loop
• Warm 12AX7 preamp tube with bypass switch
• Switchable MUTE by front panel switch or the optional FS22 footswitch
• DIRECT OUT balanced XLR with front panel LEVEL and PRE/POST switch • Switchable Ground Lift for AC ground isolation • TUNER output jack independent of MUTE switch
• High current SPEAKON® and standard 1/4” speaker output jacks.
• CLASS-D amplifier runs cool while consuming less power • Variable speed fan, silent running at low speed. • Solid metal shaft controls with threaded metal bushings mounted to front panel
• LED panel lighting enhances control visibility in dark environments
• Locking AC cord receptacle also accepts standard cords
• Circuit boards are MIL SPEC, double sided, FR-4 glass epoxy • Energy efficient worldwide power supply accepts 90-250VAC, 50-60Hz • Compact and light weight under 6lbs.
• Designed and manufactured by Carvin in the USA GETTING STARTED
1. With POWER off, connect a speaker cabinet to one of the rear SPEAKER OUTPUTs.
2. Set the DRIVE and MASTER volume to “0” and set the ACTIVE INPUT switch for your type
of bass. If Equipped with a battery, select ACTIVE.
3. Set the four tone controls to their center “0” position and the CONTOUR to FLAT. This is
the “FLAT” setting for the amp. For now, turn off the graphic EQ.
4. Now, turn the amp ON. Turn up the volume on your bass guitar. Gradually increase the
MASTER control to the desired level. If no sound is heard, turn down the MASTER and check
the MUTE switch, speaker connections, and PROTECT LED.
5. Increasing the DRIVE control will add harmonic richness to your sound. Turning up the
DRIVE also increases volume. Re-adjust the MASTER volume after adjusting the DRIVE.
6. Adjust the tone controls to your liking. Keep in mind that turning up a tone control isn’t always
the answer. Sometimes turning down one of the MID controls will get you the sound you want.
7. Need more volume? There is a limit to the amount of volume a speaker can produce and
driving a speaker beyond it’s limit can damage it. Even though these are powerful amplifiers,
adding more speakers is the only way for substantially more output. Every time you double
your speakers you increase your acoustic output by a factor of four.
This guide will help you get started. Have fun exploring the features and sounds of the BX700.
Take the time with your new amp to realize its full potential.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL! THIS UNIT CONTAINS HIGH
RISK OF ELECTRIC SHOCK VOLTAGE INSIDE!
CAUTION
RECEIVING INSPECTION—read before getting started
INSPECT YOUR UNIT FOR DAMAGE, which may have occurred during shipping. If damage
is found, please notify the shipping company and CARVIN immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your
unit, always use the original carton and packing material. This will provide the best possible
protection during shipment. CARVIN and the shipping company are not liable for any damage
caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately.
Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card for your records. Keep your
portion of the card and return the portion with your name and comments to us.
USA customers register online at: www.carvin.com/registration
All other countries register online at: www.carvinworld.com/registration
SPECIFICATIONS:
Output Power
8 ohms: 300w
4 ohms:
550w
2 ohms:
700w (2 ohm switch engaged)
Input Impedance:
>200K
Tone Controls:
CONTOUR
TREBLE: 10K
BASS: 50Hz
MIDs: 2 semi-parametric sweep: 50Hz-500Hz, 200Hz-2kHz
9-band Graphic EQ
Drive Control:
Varies input gain and harmonic content
AC Requirements:
90 to 250VAC 50/60 Hz
Power Requirements:150VA
Dimensions
14.0”W x9”D x3.15”H (with feet)
Weight :
5.9 lbs. net (2.68 kgs)
Warranty:
One year parts and labor
Optional Accessories:
FS22 footswitch
BX700RP rackmount kit
CB500 padded nylon carry bag
120V18L7 replacement 7’ locking AC cord
carvin.com 800-854-2235
76-45507A 010914
FRONT PANEL CONTROLS
2
1
6
3
4
REAR PANEL CONTROLS
7
8
9
5
10
9
­1. INPUT JACK
The 1/4” phone jack is a high impedance instrument input designed to handle
both active and passive basses in conjunction with the ACTIVE switch.
2. BLUE JEWEL LIGHT (POWER INDICATOR)
The POWER switch turns on the amplifier and is indicated by the large blue
jewel light over the input jack. This light also indicates the condition of the power
supply. If it the SPEAKER OUTPUT is shorted or if it is loaded below it’s minimum
rating, the power supply may shut off to protect the amp (see PROTECT LED).
If the power indicator goes out while playing, reset the amp by turning the
POWER switch OFF for about 10 seconds. Check your speaker connections
and the 2 OHM SWITCH setting (see 2 OHM SWITCH on rear panel). Turn the
POWER switch back ON.
3. MUTE SWITCH (FOOT-SWITCHABLE)
The MUTE switch turns off the output of the amplifier. A blue LED indicates
the MUTE switch is on. The MUTE switch is ideal for changing basses and silent
tuning on-stage. The rear tuner output is never muted. The mute feature can also
be switched with the optional FS22 footswitch.
4. ACTIVE SWITCH
Set the ACTIVE switch to the IN position for standard bass pickups. If your bass
uses a battery with an onboard active preamp, put the switch in the OUT position.
A blue LED indicates the ACTIVE switch is on.
5. DI LEVEL (DIRECT OUT) AND PRE/POST SWITCH
The DI LEVEL controls the output level of the XLR DIRECT OUTPUT jack.
The PRE/POST switch determines the source of the Direct Out signal.
Set OUT, the Direct Out signal is PRE and is only affected by the DI LEVEL. The
IN position is POST and the Direct Out is affected by the DRIVE, COMPRESSOR
and TONE controls, 9-band EQ and Effects Loop.
6. DRIVE CONTROL
The DRIVE control adjusts the input level to the CLASS A preamps. The DRIVE
control serves two purposes. The DRIVE can be used to adjust the input sensitivity for the differences in bass pickups. The DRIVE will also change the harmonic
content of your sound. Turning the knob closer to 10 will create a more overdriven
tone. The DRIVE will also change the volume of the amplifier, use it in combination
with the MASTER control to achieve the desired volume.
7. CONTOUR CONTROL
The CONTOUR control provides a variable mid-range scoop. When this control
is set to “FLAT” there is no change to the mid-range frequencies. As you turn
the contour control clockwise, the mid range is scooped at the center frequency
at 350Hz. When the CONTOUR control is set to maximum the mid-range is cut
by -15dB at 500Hz.
8. BASS and TREBLE TONE CONTROLS
The BASS and TREBLE controls are custom shaped tone controls designed to
deliver punchy lows and crisp highs for a variety of bass sounds. When a control is
turned to the right it boosts the signal and when turned to the left cuts the signal.
The affected frequencies for the BASS start at 80Hz and can deliver a great deal
8
12
11
13
14
of volume. Be careful not to distort the output or overpower your speakers. The
affected frequency for the TREBLE control begins at 5kHz.
9. SEMI-PARAMETRIC MID SWEEP TONE CONTRL (LO MID, HI MID & FREQ)
Start with the LO MID sweep. The FREQ control does not function if the GAIN
control is set in the center “0” position. To demonstrate, turn the GAIN to the right
for full boost. Now play your bass and turn the FREQ control from left to right
and notice how the added mids change frequency. Now turn the GAIN to the full
left and turn the FREQ control again and notice the mids disappear at different
frequencies. Try this with the HI MID also. The mid sweep system controls can
be very effective to fine tune your overall sound.
10. COMPRESSOR
The compressor reduces the volume of the incoming signal as it reaches a preset
maximum level. As the COMP knob is turned up (clockwise), the compressor
reduces a percentage of peak signal. This percentage is called the “compression
ratio”. When the knob is at the OFF position (full counter-clockwise) the ratio is
1:1, where all of the input signal passes through the compressor without being
affected. At the MAX setting, the compression ratio is 3:1.
The advantage of a compressor is to the reduce peaks and other sudden transients of your playing so you can increase your overall volume. For example,
in slap bass playing the plucked notes can put out peaks that would distort the
amplifier at normal playing volumes. If the amp’s volume was adjusted for these
peaks, the rest of the notes would be too quiet to hear with the band. When the
compressor is adjusted to where the LED comes on for loud peaks, the amplifier
can be played louder without distortion. It’s like having someone re-adjust the
volume of the amplifier to help prevent distortion when the peaks occur.
11. 9-BAND GRAPHIC EQUALIZER and EQ IN SWITCH (FOOTSWITCHABLE)
The 9 band graphic EQ has been designed with center frequencies most
requested by professional bass players. This EQ can be used to fine tune the
tonal content of the amp’s output. Since the graphic EQ is switchable with
either the optional FS22 footswitch or the EQ switch on the front panel, it can
be used during passages of a song when the bass needs to punch through.
Musicians that play more than one bass on stage will also find this useful
to get the sounds they desire out of each instrument. The BLUE LED located
above the GRAPHIC EQ IN switch signifies when the graphic EQ is working.
NOTE: When the front panel GRAPHIC EQ switch is off, it cannot be turned
on with the footswitch.
12. MASTER VOLUME
Use the MASTER to control the overall volume of the amplifier. Reduce the MASTER
if your sound becomes overly distorted. Using the COMPRESSOR will also help
prevent distortion or overloading of your speakers.
13. POWER SWITCH
The POWER switch turns the amp ON or OFF. It is normal for the PROTECT LED to
stay on for approximately 2-4 seconds after the the POWER switch is turned on.
24
23
22
14. PROTECT LED
The PROTECT LED indicates one of the protection circuits has activated and
no sound will be heard from the amp. To reset the amp, turn the power off for
about 10 seconds, then turn it back ON. If the PROTECT LED stays lit for more
than 5 seconds check your SPEAKER OUTPUT connections, the 2 OHM switch,
or a blocked fan intake.
15. TUBE BYPASS SWITCH
The BX700 features a 12AX7 preamp tube that can be bypassed for players who
prefer a pure solid-state signal path. Press this switch IN to bypass the tube.
16. EFFECTS LOOP
The SEND jack is the output of the preamp and is designed to deliver the proper
level for the input of an external effects processor. The SEND signal source is
after the TONE CONTROLS and COMPRESSOR. The RETURN jack is designed to
receive signals from the output of an external effects processor. When a signal
is plugged into the RETURN, it breaks the connection between the preamp and
the internal power amp. The RETURN signal goes through the GRAPHIC EQ (if
active) and MASTER control to the power amp.
17. PHONES/TUNER JACK (UNMUTED)
The PHONES/TUNER jack is a stereo 1/4” jack designed for connecting a tuner
or headphones. This output is unaffected by the MUTE function so you may tune
your bass quietly while using the MUTE. This jack will also send the mono signal
to each side of your headphones. To listen to headphones without hearing other
speakers, turn down the MASTER. The EFFECTS LOOP and GRAPHIC EQ will not
be heard in the headphones. Volume is adjusted by the DRIVE control.
18. DIRECT OUTPUT XLR JACK (MUTED)
The DIRECT OUT XLR jack provides a balanced independent output straight from
the input jack (PRE) for going direct to the main PA or recording input. The output
level is adjusted from the front panel DI LEVEL control. This output is controlled by
the MUTE function so you may tune your bass quietly while using the MUTE. The
DIRECT OUT signal is not affected by the MASTER level, TONE controls, 9-band
EQ or effects loop. The XLR is protected against Phantom power (DC voltage)
on cables coming from phantom powered mixer inputs.
19. DIRECT OUTPUT GROUND LIFT SWTICH
If a hum occurs when connecting the XLR to a mixer, try using the GND LIFT
switch. The GND LIFT switch lifts the ground pin 1 of the XLR to 100 ohms above
the chassis ground.
20. FOOTSWITCH JACK
The optional FS22 footswitch can be used to remotely control the MUTE and graphic
EQ features. The tip contact controls the MUTE and the ring contact controls the
EQ. Any standard footswitch with a stereo (TRS) plug will work.
21. SPEAKER OUTPUTS (SEE IMPEDANCE CHART and 2 OHM SWITCH)
The BX700 uses one SPEAKON® and one standard 1/4” speaker output connector.
These jacks are connected in parallel. The SPEAKON® connection is recommended.
Either or both jacks can be used so long as the total impedance does not go below
4 ohms or below 2 ohms with the 2 OHM switch pressed “IN”.
21
20
19
18
17
16
15
If you go below the minimum speaker load, the amp may shut off or the PROTECT
LED may light. To reset the amp, turn off the POWER switch and connect the
recommended load or set the 2 OHM switch.
22. 2 OHM SWITCH (SEE IMPEDANCE CHART)
This switch allows the BX700 to operate with speaker loads down to 2 OHMS. Set
this switch to the IN position if the total impedance of all speakers connected
is less than 4 OHMS.
If you go below the minimum load, the power supply may shut off and the large
blue jewel light may go out or the PROTECT LED may light. To reset the amp turn
off the POWER switch for about 10 seconds, check speaker connections, and/or
set the 2 OHM switch.
23. FAN INTAKE VENTS
The BX700 features a variable speed fan, which runs silent at low speeds. Make
sure the fan intake vents are free from blockage at all times.
24. AC POWER JACK & FUSE
The AC POWER JACK will accept 90VAC to 250VAC, 60Hz or 50Hz. A detachable
power cord is supplied (for European 230V use a CEE-7 plug cord set). Plug the
cord into a grounded 3 prong power source. No attempt should ever be made to
use the amp without the ground connected.
The FUSE is located internally near the AC input. To check or replace, first
remove the power cord and then the enclosure lid. The fuse type is a 250V Slow
Blow rated at 5A.
A locking AC cord (Carvin part# 120V18L7) is supplied with the amp. However,
a standard AC cord can be used.
To detach the cord from the amp, press the release lever on the underside of
the cord near the amp.
IMPEDANCE CHART
SPEAKER COMBINATIONS/OHMS:
Two 16 ohm speakers Two 8 ohm speakers Three 8 ohm speakers Four 8 ohm speakers Two 4 ohm speakers One 4 & one 8 ohm speaker Two 2 ohms speakers
Three 4 ohms speakers
Two 4 & one 8ohm speakers
= 8 ohms
= 4 ohms
= 2.66 ohms
= 2 ohms
= 2 ohms
= 2.66 ohms
= 1 ohm
= 1.33 ohms
= 1.6 ohms
(OK)
(OK)
(OK) ( use 2 OHM setting )
(OK) ( use 2 OHM setting)
(OK) ( use 2 OHM setting )
(OK) ( use 2 OHM setting )
(no)
(no)
(no)
">
