pneumatic roller seat - Northern Tool + Equipment

pneumatic roller seat - Northern Tool + Equipment
PNEUMATIC ROLLER SEAT
ITEM NO:17752
ASSEMBLY AND OPERATING INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MANUAL.
Specifications
ITEM
DESCRIPTION
Overall Dimensions
19-1/6”H x 15-1/4” Dia.
Tool Tray
15-1/4” Dia. x 7/8” D x 9/100” Thick
Lifting Plate
1-31/32” Dia. x 7” to 11-5/8”H
Ram Extension
2” Dia. x 7-3/4”H
Handle
5-1/2”L x 1-1/4”W x 5/16” Thick
Hub
1-5/64” I.D. x 1-5/8” H
Supporting Plate
6”L x 5-7/8”W
Casters
2-13/32” Dia. x 3/4”W
Seat
11-1/2” Dia. x 1-5/8” Thick
Material
Stamped Steel, Red Vinyl, Foam Rubber
Net Weight
12.35 Lbs.
Weight Capacity
300 Lbs.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1.
Keep work area clean. Cluttered areas invite injuries.
2.
Keep children away. Children should not be allowed in the work area. This
product is not intended for children.
3.
Use the right product for the job. There are certain applications for which
this product was designed. Do not modify this product and do not use this
product for a purpose for which it was not intended.
4.
Use eye protection. Always wear ANSI approved impact safety goggles.
5.
Maintain product with care. Inspect parts periodically and, if damaged,
have them repaired by an authorized technician.
6.
Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool.
Page 2
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur.
It must be understood by the operator that common sense and caution are
factors which cannot be built into this product, but must be supplied by the
operator.
Unpacking
When unpacking,check to make sure all parts listed on Page 4 are included.
Assembly
NOTE: You will need a crescent wrench to assemble this product.
1.
Place the Tool Tray (E) on a flat level surface.
2.
Insert the large end of the Lifting Pole (D) into the round opening in the
center of the Tool Tray.
3.
Place the Seat (A) over the top end of the Lifting Pole (D). See page 4,
Assembly Drawing and Parts List.
Operation/Maintenance/Additional Safety Warnings
1. With its convenient tool tray, comfortable padded seat, and non-marking
wheels, the Pneumatic Roller Seat is essential for the multi-tasking crafts
person.
2. To lower seat, sit on the Stool and pull up on the handle until you have
lowered the seat to the desired height (See Diagram I on Page 4). To raise
seat, stand next to the Stool and pull up on the handle. Release handle when
seat has risen to the desired height.
3. Operate on a smooth, level floor capable of supporting the seat’s capacity.
4. Do not let children play on or around the Roller Seat.
5. Do not stand on Roller Seat or use the tool tray to carry large amounts of
weight. Do not attempt to exceed the Roller Seat’s 300 lb capacity.
6. Once assembled, do not attempt to take this product apart.
7. Do not expose to heat. Parts of this product are under pressure.
8. Always hold onto seat as you sit down to keep the seat from rolling or tipping.
Page 3
Assembly Drawing
Parts List
NO.
DESCRIPTION
QTY
A
Seat Cushion
1
B
Supporting Plate
1
C
Hub
1
D
Lifting Pole
1
E
Tool Tray
1
F
2-1/2” Wheel
5
G
Handle
1
H
Truss Head Bolt M6x20
4
I
Cap Nut
5
J
Lock Washer Ø10
5
K
Rivet Ø 3 x 18
1
Diagram I, Lowering Seat
For replacement parts and technical questions, please call 1-800-222-5381.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ ThE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
Page 4
limited 90 Day Warranty
Northern Tool + Equipment Co., Inc. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTy IS exPReSSLy IN LIeU OF ALL OTHeR WARRANTIeS, exPReSS OR
IMPLIeD, INCLUDINg THe WARRANTIeS OF MeRCHANTABILITy AND FITNeSS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
Distributed by
Northern Tool + Equipment Co., Inc.
Burnsville, Minnesota 55306-6936
NorthernTool.com
Made in China
Page 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement