Smeal Fire Apparatus Co. - Metropolitan Area Planning Council

Smeal Fire Apparatus Co. - Metropolitan Area Planning Council

Quote #: 0015791 Page 1 of 8 Quote Summary with Notes Customer: Dealership: New England Fire Equipment and Apparatus 10 Stillman Road Quote No: 0015791 S.O.#: Option ID General Info 911099 911085 911059 911069 911060 911065 980003 911070 980016 911080 980015 980012 911066 911074 900466 900127 900589

UPO0000971

900679 Chassis 910129 910019 006899 006763 000954 005885 008390 910107 910087 910096 910155 Quote Name: Unit Type: FCAM Low Range Pumper Description General Info Section Custom Pumper Destination, United States Bidding Prerequisites, United States Intent of Specifications, Pumper Standards Version, NFPA 1901-2009 No Certificate Required Unit Certification, NFPA 1901-2009, Pumper Firefighting Apparatus Documentation, NFPA Owner's Manuals, Electronic, (1) USB Drive Misc. Equipment Allowance, 2,000 Lb.

Tilt Table Test, Required, 26.5 Degrees Pump Certification, Independent Third Party Pump Certification Measure, U.S. GPM Final Inspection, OEM Factory, Required Overall Height, 118 (9'-10") Overall Length, 372" (31'-0") Wheelbase, 241 (20'-1")

Angle of Approach, 27 degrees

Angle of Departure, 13 Degrees Chassis Section Commercial Chassis, Freightliner, M2 106, 4 Door Axles, Single OEM Chassis Preparations, Freightliner Air Brake Refill Inlet, with Check Valve, Manual Eject Paint Rims Primary Body Color Mud Flaps, Commercial Chassis Cab Electrical, Non-Multiplex, Integrate with Multiplex Body Top Speed, 65 mph Front Axle, 14,000 lbs Rear Axle, 27,000 lbs Frame, Double

Option ID Quote #: 0015791 Description Page 2 of 8 911110 910066 110068 910081 910083 910110 006812 110070 005084 910156 005581 005585 005582 000367 110027 910113 910115 910119 910123 001382 910112 001450 001376 910080 006803 006015 006016 005091 005092 Water/Foam Tanks 110108 910157 000350 910160 010075 008187 Hose Bed 110131 910386 910422 110151 010156 000645 Body / Pump Module Fuel Tank, 50 Gallon Engine, Cummins ISL 300hp, 860 lb. ft Auxiliary Engine Cooler, Chassis Supplied and Installed Auxiliary Braking, Exhaust Transmission, Allison 3000 Wheels, Steel Painted Primary Body Color Chassis Step Overlays, Partial, Tread Plate, 4 Door Chassis Step Lights, LED, Grote, 4 Door Battery Jumper Studs, Commercial Cab Front Bumper, Chassis Supplied and Installed Battery Charger, Dual Pro Power Super Auto Eject, Kussmaul, 15 Amp, 091-55-15-120 Charger Display, Dual Pro Power Door Open Warning Circuit, Whelen TIR3 Light in Cab SCBA Seat Brackets, (4), Zico Load and Lock Seat Brand, Bostrom Driver's Seat Type, Air Ride Officer's Seat Type, Air Ride, SCBA Rear Crew Seats, (3), LH/Ctr/RH Seats, Non-Suspension, SCBA Engine Compartment Light Air Conditioning Floor Console, Center, Between Bucket Seats, Black Line-X Finish Switch Panel, Standard 12-Switch, Floor Console Alternator, 320 Amp Vehicle Data Recorder (VDR) Seat Belt Indicator Tire Pressure Indicator, Visual, 120 PSI Fire Extinguisher, DOT Requirement Road Safety Kit, DOT Requirement Water/Foam Tanks Section Water Tank, UPF, 1000 U.S. Gallons Water Tank Mounting, Pumpers Water Tank Drain, 1-1/2" Valve, Pumpers Water Tank Fill Tower, UPF, Black Water Tank Level Gauge, Innovative Controls SL Plus, Pump Operator's Panel Water Tank Overflow, UPF, 4", Pumpers w/o EHL Hose Bed Section Hose Bed, Aluminum, Standard, Painted Primary Body Color Finish Hose Load, Double-Jacket Hose, 300' of 2-1/2" Hose Load, Double-Jacket Hose, 1000' of 5" Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Bungee, Rear Bungee, Black Hose Bed Divider, (1), 1/4" Alum., Adjustable, Abraded Hose Bed Loading Light, (1) Rear, Halogen, Unity, AG-R Body / Pump Module

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 2 of 8

Option ID 002630 120793 120874 120954 120003 000934 000474 120709 L1 Height Width Upper Depth Lower Depth Divide Height 002742 120785 Cmpt. Layout L2 Height Width Upper Depth Lower Depth Divide Height Cmpt. Layout L3 Height Width Upper Depth Lower Depth Divide Height 002742 120785 Cmpt. Layout 120648 120640 120735 R1 Height Width Upper Depth Lower Depth Divide Height Cmpt. Layout R2 Height

By: Rich Peck, 401-636-1585

Quote #: 0015791 Description Body, 100" Wide, Custom Pumper, Single-Axle, Aluminum, 1/8" Side Compartment Doors, Roll-Up Doors, ROM, Satin Finish Compartment Door Handles, All Non-Locking Rear Compartment Door, (1), ROM Roll-Up Door, Satin, Non-Locking Compartment Lighting, ROM, V4 LED (7) Compartment Finish, Line-X, Gray Air Release and Drain Holes, All Compartments Driver's (Left) Body Style, Single Axle, L1 Full, L2 Upper, L3 Full L1 Components Height - 58" Width - 40" Upper Depth - 15" Lower Depth - 26" Intermediate Divide Height - 27" Shelf, (1), Adjustable, Aluminum, Full Depth (4 Struts), Abraded Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

L2 Components Height - 25.5" Width - 55" Upper Depth - 15" Lower Depth - 0" Intermediate Divide Height - 0" The compartment layout shall be detailed at the pre-construction meeting.

L3 Components Height - 58" Width - 32" Upper Depth - 15" Lower Depth - 26" Intermediate Divide Height - 27" Shelf, (1), Adjustable, Aluminum, Full Depth (4 Struts), Abraded Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

WL1, Air Bottle Compartment, OEM Brushed SS Door, Single 8" WL3, Air Bottle Compartment, OEM Brushed SS Door, Single 8" Officer's (Right) Body Style, Single Axle, R1 Lower, R2 Lower R1 Components Height - 23" Width - 40" Upper Depth - 0" Lower Depth - 26" Intermediate Divide Height - 0" The compartment layout shall be detailed at the pre-construction meeting.

R2 Components Height - 23" Page 3 of 8

http://www.smeal.com/ Page 3 of 8

900963 003558 005118 010080 002186 003559 120489 004929 002427 005155 001210 007896 007901 120548 Option ID Width Upper Depth Lower Depth Divide Height Cmpt. Layout 120657 120667 121483 T1 Height Width Depth 120357 Cmpt. Layout 005119 900960 003598 120677 120690 002717 001296 001293 001291 009218 002272 120631 009312 121406 Quote #: 0015791 Description Page 4 of 8 Width - 32" Upper Depth - 0" Lower Depth - 26" Intermediate Divide Height - 0" The compartment layout shall be detailed at the pre-construction meeting.

WR1, Air Bottle Compartment, OEM Brushed SS Door, Single 8" WR3, Air Bottle Compartment, OEM Brushed SS Door, Single 8" Rear Body Style, Flat Back, Standard Hose Bed, One Compartment T1 Components Height - 38" Width - 41" Depth - 23" Tray, (1), Floor-Mounted Roll Out, Hansen, 600#, 100% Extension, Abraded The compartment layout shall be detailed at the pre-construction meeting.

Sub-Frame, GS-36, Hot-Dip Galvanized, Custom Pumpers, Aluminum and Galvaneal Bodies Walkways/Overlays/Stepping Surfaces, Tread Plate, NFPA 1901 Rear Deck, Bolt-On, Flat Back, Tread Plate, 13.25" Rub Rails, "C" Channel Design Tow Option, Rear, Tow Eye, One (1), Underbody Subframe Wheel Wells, Rear, Single Axle Fenderettes, (2), Single Axle, Stainless Steel Exhaust Heat Deflector Shield, 4" Access Panel for Fuel Tank Gauge, Pumpers License Plate Bracket Stainless Steel Screws Bag of Bolts Front Steps and Lighting, Cast Products, Folding Steps (3), Driver's Side Front Steps and Lighting, Cast Products, Folding Steps (3), Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On, Seven (7), 4 Driver's Side and 3 Officer's Side Handrail Material, Knurled Aluminum Handrail, Body (Front), Top, Driver's Side, Knurled Aluminum Handrails, Body (Rear), Rear Face, Vertical, Both Sides, Knurled Aluminum Handrail, Body (Rear), Below Hose Bed, Horizontal, Knurled Aluminum Ladder Storage, Above Low Sides, Officer's Side, OEM Brackets Ladder, (1), Duo-Safety, 24' Two-Section Extension, 900-A Ladder, (1), Duo-Safety, 14' Roof, 775-A Ladder, (1), Duo-Safety, 10' Folding Attic, 585-A Pike Pole Tubes, (2), Ladder Storage Above Low Sides, Mounted on Catwalk, Officer's Side Pike Pole, (1), Akron, 6' Fiberglass, Standard Hook, Ultra-Lite, UL-6 Pike Pole, (1), Akron, 8' Fiberglass, Standard Hook, UT-8 Hard Suction Hose Storage, Two (2) Hoses, Driver's Side of Water Tank, Enclosed Compartment, Tread Plate Door Hard Suction Hose, (2), Firequip, 6" x 10' (OAL 10' 6"), Maxi-Flex PVC

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 4 of 8

Option ID Quote #: 0015791 Description Page 5 of 8 009276 001224 900951 004949 110174 004731 009864 010108 009973 007160 000460 110222 Hard Suction Hose Storage, One (1) Hose, Above Officer's Side Low Cmpt, 'V' Trough (Abraded), Retaining Straps Hard Suction Hose, (1), Firequip, 6" x 10' (OAL 10' 6"), Maxi-Flex PVC Wheel Chock Storage, Under Front of Body, Driver's Side Wheel Chocks, (1) Pair, Cast Products, TMC1008-4 and Bracket, OEM Installed Pump Module, Side Mount, Independent, 1/8" Aluminum Pump Compartment Internal Lighting, LED, On-Scene Running Board, Driver's Side, Bolt-On, Tread Plate Running Board, Officer's Side, Bolt-On, Tread Plate Dunnage Compartment, Tread Plate, Above Pump Module, NO Cover Access Panel, Pump, Front Pump Module, Bolt-On, Painted Aluminum, Bolt-On Access Panel, Pump, Officer's Side Pump Module, Side-Hinged, Tread Plate, Compression Latches Pump Panels, Side Mount, Controls on Driver's Side, Black Line-X Finish, IC Bezels/Trim Rings/Labels Pump Panel Lighting, Side Panels, LED, On-Scene Night Axe Pump Panel Lighting Activation, Automatic with Park Brake Engaged Pump / Foam System 003659 910612 Pump / Foam System 110265 000090 007296 910621 910640 100266 009531 002210 100285 000112 910645 111069 006643 910503 911030 111058 911038 910527 100377 100349 100334 Tank/Pump Plumbing Labels Intakes 100382 Pump, Waterous, Single-Stage, 1250 GPM, CXVC20, Standard Impellers Mechanical Seals, Waterous Anodes, OEM, Alloy, 1 Intake Pump Rating, 1250 GPM Pump Mounting, Independent Pump Module Pump Shift and Lights, Waterous, Air-Operated Governor, Pump Boss 400, FRC Intake Relief Valve, Pump, Elkhart, Factory Preset Primer, Waterous, VPO/VPOS Oilless, VAP Master Drain Valve, Trident Pump Color Primed Black - Intakes Unpainted Pump and Engine Cooling System, Inn. Cntrls, 3/8" I.D., Hose, Controls on Pump Panel Manifold, Waterous, Standard, Side Mounts, Non-Foam Akron 8800 - Push/Pull Discharges (RC-10 on 3" or Larger) - Manual Inlets Gauge Brand, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauges - psi 0-400 Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-400 Include with Master Pressure Gauge Assembly Hardware Brand, South Park, NST Inlet Swivels, NST Discharges, TFT Storz Drains, Innovative Controls, Manual Lift Handle Pump to Tank Fill, 2", Akron 8800 2" Manual Valve, IC Push-Pull Handle Tank to Pump, 4", Akron 8800 3" Manual Valve, IC Push-Pull Handle Tank/Pump Plumbing Labels - The tank plumbing valves and controllers shall have the OEM Standard label package unless stated otherwise. The Pump-to-Tank Fill shall be labeled "TANK FILL" and shall have a Black label color. The Tank-To-Pump shall be labeled "TANK TO PUMP" and shall have a Navy Blue label color.

Intakes Steamer, Driver Side, 6", Short Tube, Volute Pump, MNST

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 5 of 8

Option ID 001252 002588 007059 001246 100386 001252 Intake Labels Discharges 002545 111712 111050 100527 002545 111712 111050 100527 002538 100659 111050 100527 100482 100663 111050 100606 002543 100658 111050 100527 007001 007013 007018 000205 009837 110311 910650 910701 Quote #: 0015791 Description Page 6 of 8 Cap, 6" NST, Vented Chrome, South Park Inlet, Driver-Side, 2-1/2", Fully Recessed Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, TSC Handle Plug, NST, 2-1/2", South Park Steamer, Officer Side, 6", Short Tube, Volute Pump, MNST Cap, 6" NST, Vented Chrome, South Park Intake Labels - All intakes shall have the OEM Standard label package unless stated otherwise. All intake labels shall be burgundy in color. Specific verbiage on each intake label tag shall be determined at the pre-construction meeting.

Discharges Discharge, Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8625, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8625, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Officer-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Officer-Side, 3", NST Valve, 3", Akron, Manual, Slow Close, 8830, Stainless Ball, Elkhart RC-10 Handwheel Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 3" FNST x 4" Storz - Storz Cap, TFT Discharge, Rear Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Crosslays, Above Pump Panel, (2) 1-1/2" Pre-Connect Hose Bed Housing Coating, Abraded Finish Flooring, Dura-Dek Crosslay Rollers Crosslay Divider, (1), Abraded Aluminum Crosslay Top / End Cover, Vinyl, C-Rail and Velcro Top and Footman Loop and J-Hook on Bottom, Black Crosslay End Covers, Incorporated with the Top Cover Preconnect, Crosslay/Speedlay, 1-1/2", NST

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 6 of 8

Option ID Quote #: 0015791 Description Page 7 of 8 910654 100653 111050 Crosslay Load, 200' of 1-3/4" Hose, Single Stack Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Preconnect Discharge 910526 910701 910654 100653 111050 910526 Preconnect, Crosslay/Speedlay, 1-1/2", NST Crosslay Load, 200' of 1-3/4" Hose, Single Stack Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Preconnect Discharge Discharge Labels Discharge Labels - All discharges shall have the OEM Standard label package unless stated otherwise. Each discharge label shall be a unique color. Specific verbiage and colors on each discharge label tag shall be determined at the pre-construction meeting.

Low Voltage Low Voltage 002955 911058 002849 008730 110366 006261 002199 000748 110406 Upper C Light / Lens Color 110506 Lower Zone Light/Lens Color Electrical System, Pumper, Weldon V-MUX Multiplex, QL-12 Harnesses, Sealed Switches Electrical System Test, 12 Volt Tail Lights, LED, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup/Warning, 4 Light Vertical Casting Turn Signals, (2) in Rub Rail, LED, Truck-Lite, Model 21 Ground Lights, LED, Truck-Lite Model 44, Activation by Park Brake Clearance Lights, LED, Grote, Red (Pumper, Squrt, and TeleSqurt) Alarm, Back-Up, Ecco 510 Dba Upper Zone A, Lightbar, Whelen, 55", Freedom LED, Flat Roof, 6 Red, 2 White Upper Zone C, Rotating Beacons (2), Whelen, RB6 Light/Lens Color - The driver's and officer's side beacons shall both have red LED's and red lenses.

Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, 600 Series Light/Lens Color - The lower zone warning lights shall all have red LED's and red lenses.

Line Voltage Paint / Striping / Decals Line Voltage Paint / Striping / Decals 900717 900734 009171 008841 001170 006089 001033 120031 911237 900879 004522 008610 900906 900935 Chassis Paint, Chassis Manufacturer Painted, Single Tone Chassis Paint Color, Single Tone, Red, PPG# FBCH-71096-ALT Body Paint, Single Tone, Pumper, Aluminum Material Body Paint Color, Pumper/Squrt/TS, Single Tone, Red, PPG# FBCH-71096-ALT Under Body Finish, Two-Step Undercoating Process Corrosion Protection, Electrolysis Corrosion Kontrol (ECK) Touchup Paint, 2 Oz. Bottle 100 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" Reflective Lettering, White Front Cab Striping, Wrap to Grill Rub Rail Striping, 2", Silver, Reflective, Pumper/Squrt/TS Body Striping, Pumper/Squrt/TS, 4", Straight Around Perimeter Main Stripe Color, White Chevron Color, Red / Fluorescent Yellow-Green

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 7 of 8

Option ID 006009 Warranties W05451 990028 W05901 990032 WLF800 990030 W10201 W05810 Quote #: 0015791 Description Chevron Layout, Rear Body Surface, Painted Storage Doors Warranties Warranty, Parts and Labor, 5 Year (Pumper) Warranty, Body Structural Integrity, 10 Year Warranty, 100% V-Mux Electrical, Smeal Parts and Labor, 5 Year (Pumper) Warranty, Plumbing, Stainless, 10 Year Warranty, Water Tank, UPF, Standard Lifetime Warranty, Substructure, Galvanized, 20 Year, Pumper, Rescue Warranty, Paint, 10 Year, Corrosion, 10 Year (Pumper) Warranty, Pump, Waterous, Standard 5 Year Page 8 of 8

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 8 of 8

Smeal Fire Apparatus Co.

PREREQUISITE BIDDING REQUIREMENTS SO#: Any manufacturer submitting a proposal or bid, to these specifications, shall meet the following conditions:

• • • •

The manufacturer of the apparatus herein specified, shall be wholly owned (100%) and managed by a Company, Corporation, and/or Parent Company that is wholly based and permanently resides in the United States of America.

The Company, Corporation, and/or Parent Company, and all assets belonging to such, shall be wholly owned and managed (100%) by the entities specified above Any proposal, bid, or response to these specifications by any foreign based, owned, or managed (in part or in whole) Company, Corporation, and/or Parent Company shall be cause for immediate rejection.

Any proposal, bid, or response to these specifications by any Company, Corporation, and/or Parent Company, that is owned, operated, managed, or held in contract, in part or wholly by a partnership or other agreement, shall be cause for immediate rejection.

Exceptions to these conditions will not be allowed under any circumstances.

INTENT OF SPECIFICATIONS It is the intent of these specifications to cover the furnishing and delivery to the purchaser of a complete apparatus equipped as herein specified. With a view to obtaining the best results and the most acceptable apparatus for service in the fire department, these specifications cover the general requirements as to the type of construction, together with certain details as to finish, equipment, and appliances with which the successful bidder must conform. Minor details of construction and materials where not otherwise specified are left to the discretion of the contractor, who shall be solely responsible for the design and construction of all features.

Bids shall only be considered from companies that have an established reputation in the field of fire apparatus construction and have been in business for a minimum of 50 years.

Each bidder shall furnish satisfactory evidence of his ability to construct the apparatus specified, and shall state the location of the factory where the apparatus is to be built.

The bidder shall also show that they are in a position to render prompt service and furnish replacement parts for said apparatus.

CONTRACTOR'S SPECIFICATIONS Each bid shall be accompanied by a set of "Contractor's Specifications" consisting of a detailed description of the apparatus and equipment proposed and to which the apparatus furnished under contract must conform.

These specifications shall indicate size, type, model, and make of all component parts and equipment.

TIMELY PROPOSALS It is the bidder's responsibility to see that their proposals arrive on time. Late proposals, facsimiles, e-mails, telegram, or telephone bids shall not be considered.

DRAWINGS All bid drawings shall be stamped PROPOSAL.

Quote No: 0015791 Page 1 of 49

Smeal Fire Apparatus Co.

SO#:

• • • • • • • •

A total of six (6) packets of 11" x 17" drawings, each packet complete with a single view drawing for each side of the apparatus shall be supplied

• • •

All drawings shall be drawn and printed to an appropriate scale to maximize the size of the apparatus on each 11" x 17" sheet of paper.

Compartment door opening dimensions shall be shown in each compartment.

Drawings shall be five (5) views. (left, right, front, rear, top) with the exception of chassis that are not always available as AutoCAD drawings

Rear plumbing, such as 2-1/2" discharges, rear steamers, and direct tank fills, shall be shown

Ladders shall be labeled with a letter designation referring to the table for an explanation of the ladder type

OAL (overall length) in feet and inches - Estimated length shall be rounded up to the nearest inch

OAH (overall height) in feet and inches - Estimated height shall be rounded up to the nearest inch

• • • • • •

Body dimensions shown - pump house width and front of the body to centerline of the rear axle Wheelbase in inches Estimated in-service weight Turning clearance radius Front and rear overhang in inches No pump panel or instrument panel controls, discharges or inlets. To be blank and labeled "Pump Panel"

• • • • • • • •

Water tank outline Foam tank(s) fill towers Exterior mounted hard suction hose Warning lights D.O.T. lights Generator outline No front bumper layout Rollup doors will be shown in open position. Lap doors will be shown in the closed position

Compartment depth break over measurement. The measurement where the compartment switches from full depth to shallow depth

• •

Angle of approach and departure Top view of chassis Text Block Items Chassis model Water tank capacity Foam tank capacity Hose bed capacity in cubic feet Total compartment cubic feet Drawing box is to read "BID" and utilize the bid number Drawings shall be printed on white paper with black ink; blue line drawings shall not be acceptable.

PURCHASER'S OBLIGATIONS The purchaser reserves the right to accept or reject any or all bids on such basis as the purchaser deems to be in its best interest. All bidders shall be advised that the purchaser is not bound in any manner to automatically accept the lowest bid. The purchaser shall Quote No: 0015791 Page 2 of 49

Smeal Fire Apparatus Co.

only be obligated to purchase the lowest bid that meets these detailed specifications as closely as possible.

SO#: SAFETY REQUIREMENTS It is required that the bidder shall meet all State and Federal safety standards and laws that are in effect on the date of the bid for the item(s) that are being specified and the particular use for which they are meant.

ACQUAINTANCE WITH SPECIFICATIONS It is the responsibility of the bidder to review all of the bidding requirements. Failure of a bidder to be acquainted with this information shall not relieve them from any obligations of the bid requirements.

QUALITY AND WORKMANSHIP The design of the apparatus shall embody the latest approved automotive engineering practices. Experimental designs and methods shall not be acceptable.

The workmanship shall be of the highest quality in its respective field. Special consideration shall be given to the following points: accessibility of the various units that require periodic maintenance, ease of operation (including both pumping and driving), and symmetrical proportions.

GENERAL CONSTRUCTION The complete apparatus, assemblies, subassemblies, component parts, and so on, shall be designed and constructed with due consideration to the nature and distribution of the load to be sustained and to the general character of the service to which the apparatus is to be subjected when placed in service.

All parts of the apparatus shall be strong enough to withstand the general service under full load. The apparatus shall be so designed that the various parts are readily accessible for lubrication, inspection, adjustment and repair.

The apparatus shall be designed and constructed, and the equipment so mounted, with due consideration to distribution of the load between the front and rear axles, and side to side loading that all specified equipment, including a full complement of specified ground ladders, full water tank, loose equipment, and firefighters; shall be carried without overloading or damaging the apparatus as per requirements defined in NFPA 1901.

The main apparatus body structure shall have an approximate width of 100" in order to maximize the enclosed compartment space of the apparatus. The 100" wide measurement represents the main body structure measured from the bottom, outermost rear corners of the apparatus body structure. Components affixed or fastened to the apparatus will increase the body width proportionately.

LIABILITY The bidder, if their bid is accepted, shall defend any and all suits and assume all liability for the use of any patented process, device or article forming a part of the apparatus or any appliance furnished under the contract.

Quote No: 0015791 Page 3 of 49

Smeal Fire Apparatus Co.

WARRANTY A copy of the warranties for the chassis, pump, body, paint, and water tank shall be furnished with each bidder's proposal.

BID FORMS / SPECIFICATIONS SO#: All bid forms shall be submitted on the attached bid form. The bid form and/or these specifications shall be filled out by checking either the "YES" or "NO" column for each and every section/paragraph. Failure to use this form and/or these specifications shall be cause for immediate rejection of any bid.

EXCEPTION TO SPECIFICATIONS The following chassis, pump, and body specifications shall be strictly adhered to.

Exceptions shall be allowed if they are equal to or superior to that specified (as judged by the customer), and provided they are listed and fully explained on a separate page entitled "EXCEPTIONS TO SPECIFICATIONS". Exception lists shall refer to the specification page number. Each check in the "NO" column shall be listed and fully explained. Where no check is made in a particular paragraph with either "YES" or "NO", it shall be assumed the bidder is taking exception to that paragraph. If a paragraph contains an empty column, where the bidder neglected to check the proper "YES" or "NO" column, it is assumed the bidder is not conforming to the requirements of this paragraph. If no explanation is given in the "EXCEPTIONS TO SPECIFICATIONS" document, the bid is subject to immediate rejection.

PROPOSALS TAKING TOTAL EXCEPTION TO THESE SPECIFICATIONS WILL BE IMMEDIATELY REJECTED.

The buyer is aware that all bidders shall have to take some exceptions therefore; BIDDERS THAT TAKE NO EXCEPTIONS shall BE REQUIRED TO MEET EVERY PARAGRAPH TO THE FULLEST EXTENT SHOULD THEIR BID BE ACCEPTED. It is the intent of the purchaser to receive bids that do not require telephone calls or other communications to ascertain what a bidder is intending to supply.

Upon delivery, the apparatus shall be inspected against THESE specifications and not those supplied by the bidder with their proposal. Deviations shall not be acceptable unless they were noted as exceptions at the time of bid and the apparatus shall be rejected until said deviations are corrected to the satisfaction of the buyer.

Decisions regarding equal to or better than, shall be the sole responsibility of the recipient of the bids rather than those companies submitting bids. All deviations, regardless of significance must be explained in the "EXCEPTIONS TO SPECIFICATIONS" section of the bid.

When exceptions are not taken but inconsistencies are noted in the submitted detailed specifications, the bid may be subject to rejection.

ROADABILITY The apparatus, when fully equipped and loaded, shall be capable of the following performance while on dry paved roads that are in good condition: Quote No: 0015791 Page 4 of 49

Smeal Fire Apparatus Co.

SO#:

• • • •

Accelerating from 0 to 35 mph (55km/hr) within 25 seconds on a 0 percent grade.

Attaining a speed of 50 mph (80 km/hr) on 0 percent grade.

Maintaining a speed of at least 20 mph (32 km/hr) on any grade up to and including 6 percent.

The maximum top speed of the apparatus shall not exceed the tire manufacturer's maximum speed rating for the tires installed on the apparatus.

FAILURE TO MEET TESTS In the event the apparatus fails to meet the test requirements of these specifications on the first trials, second trials may be made at the option of the bidder within 30 days of the date of the first trials.

Such trials shall be final and conclusive and failure to comply with these requirements shall be cause for rejection. Failure to comply with changes as required to conform to any clause of the specifications within 30 days after notice is given to the bidder of such changes, shall be cause for rejection of the apparatus.

Permission to keep or store the apparatus in any building owned or occupied by the Department during the specified period, with the permission of the bidder, shall not constitute acceptance. No Exceptions PROPOSAL SEQUENCE Bid specifications shall be submitted in the same sequence as these specifications for ease of checking compliance. There shall be no exceptions allowed to this requirement.

The apparatus committee intends to be thorough during the evaluation of bids process.

In order to maximize efficiency and minimize the time it takes to thoroughly evaluate all received bids this requirement must be strictly adhered to.

AWARD OF CONTRACT All bids submitted shall be good for a minimum of 30 days during which time bid securities submitted with the proposals shall be held by the purchaser. Criteria for the award shall include, but not be limited to, the following:

• • • • • • • • • • • • •

Apparatus Performance And Safety Levels / Considerations Completeness of proposal Accuracy of accompanying data Past performance of bidder Compliance with the detailed specifications Compliance with purchasers request(s) for personnel qualifications or certifications Exceptions and clarifications Financial stability of bidder Local representation of the manufacturer Serviceability of the proposed apparatus Service capabilities of the bidder's local representative Compliance with NFPA 1901 Any other factor the purchaser deems relevant After the evaluation and award process is complete, all bidders shall be notified of the results and securities shall be returned.

Quote No: 0015791 Page 5 of 49

Smeal Fire Apparatus Co.

SO#: NFPA 1901-2009 The National Fire Protection Association "Standard for Automotive Fire Apparatus", 2009 edition, is hereby adopted and made a part of these specifications, the same as if it were written out in full detail, with the exception of the section dealing with "Equipment Recommended for Various Types of Apparatus". Bidders shall provide the equipment requested herein and the buyer shall supply the rest before the apparatus is put into service. It is the intent of the purchaser to purchase an apparatus that meets 100% of the minimum standards defined and outlined in NFPA 1901-2009 edition. There are to be no exceptions to this requirement.

NO NFPA CERTIFICATION No National Fire Protection Association "Standard for Automotive Fire Apparatus" certification shall be required with finished apparatus.

CONSTRUCTION DOCUMENTATION The contractor shall supply, at the time of delivery, at least one (1) copy of the following documents: 1. The manufacturers record of apparatus construction details, including the following information:

• • • • • • • • • • • • • • • • • • •

Owners name and address Apparatus manufacturer, model, and serial number Chassis make, model, and serial number GAWR of front and rear axles Front tire size and total rated capacity in pounds or kilograms Rear tire size and total rated capacity in pounds or kilograms Chassis weight distribution in pounds with water and manufacturer mounted equipment (front and rear) Engine make, model, serial number, rated horsepower and related speed, and governed speed Type of fuel and fuel tank capacity Electrical system voltage and alternator output in amps Battery make, model, and capacity in cold cranking amps (CCA) Chassis transmission make, model, and serial number; and if so equipped, chassis transmission PTO(s) make, model, and gear ratio If applicable, the pump make, model, rated capacity in gallons or liters per minute, and serial number Pump transmission make, model, serial number, and gear ratio, if unit is equipped with a pump If applicable, the auxiliary pump make, model, rated capacity in gallons or liters per minute, and serial number Water tank certified capacity in gallons or liters On aerial apparatus, the device type, rated vertical height in feet or meters, rated horizontal reach in feet or meters, and rated capacity in pounds or kilograms Paint manufacturer and paint number(s) Company name and signature of responsible company representative 2. Certification of slip resistance of all stepping, standing, and walking surfaces 3. If the apparatus has a fire pump, a copy of the following shall be provided: pump Quote No: 0015791 Page 6 of 49

Smeal Fire Apparatus Co.

SO#: manufacturers certification of suction capability, apparatus manufacturers approval for stationary pumping applications, engine manufacturers certified brake horsepower curve showing the maximum governed speed, pump manufacturers certification of the hydrostatic test, and the certification of inspection and test for the fire pump 4. If the apparatus has an aerial device, the certification of inspection and test for the aerial device, and all the technical information required for inspections to comply with NFPA 1914, Standard for Testing Fire Department Aerial Devices 5. If the apparatus has a fixed line voltage power source, the certification of the test for the fixed power source 6. If the apparatus is equipped with an air system, test results of the air quality, the SCBA fill station, and the air system installation 7. Weight documents from a certified scale showing actual loading on the front axle, rear axle(s), and overall fire apparatus (with the water tank full but without personnel, equipment, and hose) 8. Written load analysis and results of the electrical system performance tests 9. When the apparatus is equipped with a water tank, the certification of water tank capacity OPERATION AND SERVICE DOCUMENTATION The contractor shall supply, at time of delivery, at least two (2) sets of complete operation and service documentation covering the completed apparatus as delivered and accepted. The documentation shall address at least the inspection, service, and operations of the fire apparatus and all major components thereof. The contractor shall also provide documentation of the following items for the entire apparatus and each major operating system or major component of the apparatus: Quote No: 0015791 Page 7 of 49

Smeal Fire Apparatus Co.

SO#:

• • • • • • • • • • • • • • • • • • • •

Manufacturers name and address Country of manufacturer Source of service and technical information Parts and replacement information Descriptions, specifications, and ratings of the chassis, pump, and aerial device Wiring diagrams for low voltage and line voltage systems to include the following information: representations of circuit logic for all electrical components and wiring, circuit identification, connector pin identification, zone location of electrical components, safety interlocks, alternator-battery power distribution circuits, and input/ output assignment sheets or equivalent circuit logic implemented in multiplexing systems Lubrication charts Operating instructions for the chassis, any major components such as a pump or aerial device, and any auxiliary systems Precautions related to multiple configurations of aerial devices, if applicable Instructions regarding the frequency and procedure for recommended maintenance Overall apparatus operating instructions Safety considerations Limitations of use Inspection procedures Recommended service procedures Troubleshooting guide Apparatus body, chassis, and other component manufacturers warranties Special data required by this standard Copies of required manufacturer test data or reports, manufacturer certifications, and independent third-party certifications of test results A material safety data sheet (MSDS) for any fluid that is specified for use on the apparatus The contractor shall deliver with the apparatus all manufacturers operations and service documents supplied with components and equipment that are installed or supplied by the contractor.

STATEMENT OF EXCEPTIONS The proposed apparatus as described in this specification document and all related material with the bid package shall meet or exceed all applicable sections for the category of apparatus as defined by NFPA 1901, unless specifically noted within this specification or other official documents associated with this bid.

Should any area, section or portion of the apparatus not meet the intent and applicable requirements, a clearly defined listing or explanation of what and why compliance was not achieved shall be provided to the purchaser at the time of delivery.

OWNER'S MANUAL There shall be an owner's manual containing the construction, operation, and service documentation provided on a USB Drive. There shall be one (1) copy of the USB provided with the apparatus.

ELECTRICAL MANUAL A complete electrical manual for the apparatus shall also be provided on the USB Drive.

Quote No: 0015791 Page 8 of 49

Smeal Fire Apparatus Co.

SO#: This manual shall be specifically prepared for this individual unit rather than a generic schematic manual designed to accommodate all apparatus. The electrical manual shall also include electrical schematics, harness layouts, V-Mux specifications (including Node Input/output Spreadsheet and Node Relationship Spreadsheet), and Master Wire Listing.

A contact letter shall also be provided by the electrical engineer, who built the manual, with instructions on using the manual and contact information for assistance with electrical manual questions.

ELECTRICAL SCHEMATICS There shall be a section of the electrical manual that shall include schematics of the electrical system and components on the apparatus. These schematics shall be specifically prepared for this individual unit rather than a generic schematic designed to accommodate all apparatus.

PUMP PLUMBING SCHEMATICS (if applicable) There shall be a section of the electrical manual that shall include a schematic of the pump plumbing. This schematic shall be specifically prepared for this individual unit rather than a generic schematic designed to accommodate all apparatus.

HYDRAULIC SCHEMATICS (if applicable) There shall be a section of the electrical manual that shall include schematics of the hydraulic components on the apparatus including but not limited to:

• • • •

Ladder Rack(s) and Hose Bed Door(s) (if applicable) Aerial – Retraction/Extension (if applicable) Aerial – Rotation (if applicable) Tiller – HVAC Hydraulics System (if applicable) FIRE APPARATUS SAFETY GUIDE There shall be one (1) printed copy of the FAMA Fire Apparatus Safety Guide provided with the apparatus.This guide provides safety instructions for operations of the fire apparatus.

MISCELLANEOUS EQUIPMENT ALLOWANCE The Gross Axle Weight Rating (GAWR) and the Gross Combined Weight Rating (GCWR) or Gross Vehicle Weight Rating (GVWR) of the chassis shall be adequate to carry the weight of the unequipped apparatus with the water tank and other tanks full, specified hose load, unequipped personnel weight, ground ladders, and miscellaneous equipment allowance of 2,000 pounds.

TILT TABLE TESTING The apparatus shall be tested to verify the stability to 26.5 degrees in both directions.

The apparatus shall be tested while loaded with fuel, fire fighting agents, hose, ladders, weight of 250 lbs. per seat, and also weight that is equivalent to the miscellaneous equipment that shall be carried. The weight added to the apparatus for testing purposes shall be distributed approximately to the in-service use, yet not to exceed the manufacturer's compartment ratings.

VEHICLE STABILITY Quote No: 0015791 Page 9 of 49

Smeal Fire Apparatus Co.

SO#: The apparatus shall comply with the requirements of NFPA 1901 as it applies to vehicle stability. The particular apparatus as described in the specification provided within the bid package shall be classified into one of the following categories:

• • •

The apparatus shall go through actual tilt table testing. This shall be determined by the apparatus manufacturer.

The apparatus shall be equipped with a rollover stability control system as defined in section 4.13.1.2 of NFPA 1901.

The apparatus shall be deemed a similar apparatus and meeting the intent of section 4.13.1.1.2 of NFPA 1901.

INDEPENDENT THIRD PARTY PUMP CERTIFICATION The fire pump shall be tested and certified by Underwriter's Laboratories, a nationally recognized independent third party testing company. Tests shall be conducted so that the pump performs as listed below:

• • • •

100% of rated capacity at 150 pounds net pressure 70% of rated capacity at 200 pounds net pressure 50% of rated capacity at 250 pounds net pressure 100% of rated capacity at 165 pounds net pressure The entire pump, both suction and discharge passages, shall be hydrostatically tested to a pressure of 600 PSI. The pump shall be fully tested at the pump manufacturer’s factory to the performance spots as outlined by NFPA 1901. The pump shall be free from objectionable pulsation and vibration.

PUMP CERTIFICATION The pump shall be certified in U.S. gallons per minute (GPM).

FINAL INSPECTION The customer and/or dealer representative will inspect the final apparatus prior to it leaving the apparatus body manufacturer’s facility. This will allow any changes that may be required, to be done so in a timely and inexpensive manner. After leaving the facility, all repairs or alterations will be performed by either the Dealer or an OEM approved service center.

OVERALL HEIGHT The actual overall height of the vehicle shall be approximately 118" (9'-10") from the ground. This measurement shall be taken with the tires properly inflated with the apparatus in the unloaded condition. The actual measurement shall be taken at the highest point of the apparatus.

OVERALL LENGTH The actual overall length of the vehicle shall be approximately 372" (31'-0").

WHEELBASE The actual wheelbase of the vehicle shall be approximately 241" (20'-1").

Angle of Approach, 27 degrees Quote No: 0015791 Page 10 of 49

Smeal Fire Apparatus Co.

ANGLE OF A DEPARTURE SO#: The actual angle of departure of the vehicle shall be a minimum of 13 degrees.

FREIGHTLINER M2 106 CHASSIS The chassis shall be a four (4) door Freightliner M2 106.

AIR BRAKE REFILL INLET WITH CHECK VALVE An air inlet shall be located near the driver's door. This fitting shall be connected to the air brake system "wet" tank to allow a remote air source to maintain a usable pressure in the chassis brakes. A check valve shall be provided as part of the system.

MANUAL EJECT The air inlet shall be supplied with a manual eject.

PAINT CHASSIS RIMS - PRIMARY BODY COLOR The chassis rims shall be painted with PPG polyurethane enamel paint. The paint shall be the primary body color.

MUD FLAPS There shall be four (4) mud flaps provided by the apparatus manufacturer. The mud flaps shall be a minimum of 3/8" thick to prevent "sailing." INTEGRATE CHASSIS ELECTRICAL SYSTEM TO V-MUX BODY The chassis 12 volt non-V-Mux electrical system will be integrated to the apparatus body 12 volt V-Mux multiplex electrical system.

AUXILIARY ENGINE COOLER A single bundle type coolant to water heat exchanger shall be installed between the engine and the radiator by the chassis manufacturer. The heat exchanger shall be designed to prohibit water from the pump from coming in contact with the engine coolant.

This shall allow the use of water from the discharge side of the pump to assist in cooling the engine.

PARTIAL CHASSIS CAB STEP OVERLAYS There shall be partial tread plate step overlays installed on each side of the chassis cab.

CHASSIS GROUND LIGHTING The 4-door commercial chassis shall have Grote, model 61E41, white 4" round LED lights installed beneath the apparatus in areas where personnel may be expected to climb on and off of the apparatus. The lights shall illuminate the ground within 30" of the apparatus to provide visibility of any obstructions or hazards.

BATTERY JUMPER STUDS There shall be a pair of battery jumper studs provided on the driver’s side of the Quote No: 0015791 Page 11 of 49

Smeal Fire Apparatus Co.

apparatus. The studs shall allow the vehicle to be jump started in an emergency due to battery failure.

SO#: CHASSIS SUPPLIED FRONT BUMPER The front bumper shall be chassis supplied and installed.

BATTERY CHARGER A Pro Charging System Professional Series model PS2, two bank battery charger shall be installed and wired to the shoreline receptacle and the chassis batteries. The battery charger shall be a 120 volt, 30 amp (15 amps per bank), and automatic battery charger.

The charger shall be a fully automatic waterproof system. Each bank of the charging system shall be capable of producing a charge to bring the batteries back to full charge.

The unit shall turn off when the battery is at full charge and turn on automatically if the battery voltage drops. There shall be a charge indicator display provided on the charger.

The unit shall have as standard a three year warranty.

KUSSMAUL SUPER AUTO EJECT SHORELINE RECEPTACLE A flush mount Kussmaul 15 Amp Super Auto Eject 120 Volt shoreline receptacle, model #091-55-15-120 shall be installed on the driver's side of the chassis cab by the driver's door. The Auto Eject shall be a completely sealed automatic power line disconnect to prevent contamination of the mechanism by road dirt and ensures long reliable life.

There shall be an internal contact arrangement that opens and closed the 120 volt circuit to eliminate arcing. An industrial grade connector specially selected to function reliably with the Auto Eject shall be provided.

REMOTE CHARGE INDICATOR A Dual Pro Power Remote Charge Indicator shall be provided in a remote location to show what the status of the charge on the batteries.

HAZARD AND DOOR OPEN WARNING CIRCUIT

• •

There shall be a hazard and "open door" warning circuits tied to a Whelen TIR3™ warning light in the chassis to alert the driver of an unsafe condition for moving the apparatus. The light shall be red and shall be illuminated automatically when the parking brake is not fully engaged and any of the following conditions exist:

Any equipment compartment door that is not closed (excluding compartments with 4 ft³ (0.1 m³ ) or less of volume; or have an opening of 144 in2 (92,000 mm2) or less; or doors that do extend sideways beyond the mirrors or up above the top of the fire apparatus).

Any ladder or equipment rack that is not in the stowed position.

Any device or component that is permanently attached to the apparatus that is open, extended, or deployed in a manner that is likely to cause damage to the apparatus that has been specified as being tied to the hazard warning circuit.

There shall be a warning placard near the warning light that reads "DO NOT Move Apparatus When Light Is On." ZICO "LOAD AND LOCK" SCBA BRACKET There shall be four (4) Zico, model ULLH, "Load and Lock" brackets installed in the Quote No: 0015791 Page 12 of 49

Smeal Fire Apparatus Co.

SCBA seats in the chassis cab. The brackets shall meet the NFPA 1901 for 9-G force testing for in cab mounting.

SO#: ENGINE COMPARTMENT WORK LIGHT There shall be one (1) 12 volt work light installed in the chassis engine compartment.

FLOOR MOUNTED CONSOLE BETWEEN BUCKET SEATS There shall be a floor mounted console provided between the officer and driver’s seats.

The console shall be used for mounting of siren controls and department supplied radio equipment. The console shall be covered with Black Line-X, a thermoplastic polyurethane coating.

SWITCH PANEL There shall be a switch panel provided between the front bucket seats in the cab. The panel shall be large enough to accommodate twelve (12) separate switches.

VEHICLE DATA RECORDER

• • • • • • • • • • •

There shall be a Weldon Technologies series 6444 Vehicle Data Recorder (VDR) installed in the chassis cab to collect essential information in order to assist in the training and safety efforts of the department. The VDR shall be capable of recording 100 engine hours worth of minute-by-minute information. The VDR shall be password protected by the user in order to prevent data tampering by unapproved personnel. The collected data shall be easily extracted by a standard mini USB cable. The data collected shall include the following: Vehicle speed (mph) Acceleration (mph/sec) Deceleration (mph/sec) Engine speed (RPM) Engine throttle position (% of full throttle) Anti-lock braking system (on/off) Seat occupied status (Occupied: yes/no by position) Seat belt status (Buckled: yes/no by position) Master optical warning device switch (on/off) Time (24 hour clock) Date (year/month/day) SEAT BELT INDICATOR There shall be an indicator module located within view for the driver or officer to easily see which seats are occupied and to insure that seat belts are being utilized.

A green signal indicates the seat is occupied and the seat belt is properly fastened. A red signal indicates that the seat is occupied; however, the seat belt is not fastened. When the seat is vacant the signal shall not be illuminated.

VISUAL TIRE PRESSURE INDICATOR Each tire shall be equipped with a visual indicator to monitor tire pressure. The tire Quote No: 0015791 Page 13 of 49

Smeal Fire Apparatus Co.

pressure indicator will display the following:

• • •

Green – tire is properly inflated, Half green/half red – tire is approximately 10% under inflated, Red – tire is 20% or more under inflated.

DOT FIRE EXTINGUISHER SO#: There shall be one (1) 2-1/2 lb. BC DOT approved fire extinguisher shipped loose in the cab of the apparatus.

ROAD SAFETY KIT There shall be a road safety kit provided with the apparatus. The kit shall consist of three (3) DOT approved reflective triangles.

WATER TANK The apparatus shall be equipped with a United Plastic Fabricating 1000 U.S. gallon water tank. Certification of the tank capacity shall be recorded on the manufacturer's record of construction and shall be provided to the purchaser upon delivery of the apparatus. The UPF® water tank shall be constructed of 1/2" thick PT2E™ polypropylene sheet stock. This material shall be a non-corrosive stress relieved thermoplastic, black in color, and U.V. stabilized for maximum protection.

BOOSTER TANK The booster tank shall be of a specific configuration and shall be so designed to be completely independent of the body and compartments. All joints and seams shall be nitrogen welded and tested for maximum strength and integrity. The top of the booster tank shall be fitted with removable lifting eyes designed with a 3 to 1 safety factor to facilitate easy removal.

TANK BAFFLES The transverse swash partitions shall be manufactured of 3/8" PT2E™ polypropylene (natural in color) and extend from approximately 4" off the floor to just under the cover.

The longitudinal swash partitions shall be constructed of 3/8" PT2E polypropylene (natural in color) and extend to the floor of the tank through the cover to allow for positive welding and maximum integrity. All partitions shall be equipped with vent and air holes to permit movement of air and water between compartments. The partitions shall be designed to provide maximum water flow. All swash partitions shall interlock with one another and be welded to each other as well as to the walls of the tank.

TANK SUMP There shall be one (1) sump in the bottom of the water tank. The sump shall be constructed of 1/2" polypropylene and shall be located in the left front quarter of the tank.

On all tanks that require a front suction, a 4" schedule 40 polypropylene pipe shall be installed that will incorporate a dip tube from the front of the tank to the sump location.

The sump shall be used as a combination clean-out and drain. All tanks shall have an anti-swirl plate located approximately 2" above the sump to pre-vent air from being entrained in the water while pumping.

Quote No: 0015791 Page 14 of 49

Smeal Fire Apparatus Co.

TANK FILL CONNECTION SO#: All tank fill couplings shall be backed with flow deflectors to break up the stream of water entering the tank, and shall be capable of withstanding sustained fill rates of up to 1,000 GPM.

TANK LID The tank lid shall be constructed of 1/2" thick PT2E™ polypropylene to incorporate a multi three-piece locking design that allows for individual removal and inspection if necessary. The tank lid shall be recessed 3/8" from the top of the tank and shall be welded to both sides and longitudinal partitions for maximum integrity. Each one of the lids shall have hold downs consisting of 2" polypropylene dowels spaced a maximum of 30" apart. These dowels shall extend through the covers and shall assist in keeping the covers rigid under fast filling conditions. A minimum of two lifting dowels shall be drilled and tapped 1/2" x 13" to accommodate the lifting eyes.

WATER TANK MOUNTING The water tank cradle shall be an integral part of the body sub-frame. Please reference the sub-frame section for complete water tank mounting information.

WATER TANK DRAIN There shall be a 1-1/2" drain valve provided under the sump of the water tank. The valve shall include a locking lever to prevent accidental draining of the water tank.

WATER TANK FILL TOWER The tank shall have a combination vent and manual fill tower marked "Water Fill." The fill tower shall be constructed of 1/2" PT2E™ polypropylene and shall be a minimum dimension of 8" x 8" at the outer perimeter. The tower shall be located in the left front corner of the tank. The tower shall have a 1/4" thick removable polypropylene screen and a PT2E™ polypropylene hinged-type cover. The fill tower shall be black in color.

WATER TANK LEVEL GAUGE There shall be one (1) Innovative Controls SL Plus Tank Level Monitor System provided on the pump operator's control panel. The system shall include one (1) electronic display module(s), a stainless steel pressure transducer sender unit, and the necessary wiring with water-tight plug terminations that do not require sealing grease.

The master display module shall show the tank level using 16 super-bright easy-to-see LEDs. Tank level indication shall be achieved by the appropriate illumination of 4 horizontal rows of LEDs, with 4 LEDs per row. Full and near-full levels shall be indicated with the illumination of all 4 rows of LEDs, including the illumination of the top row of 4 green LEDs. Tank levels between ½ and ¾ full shall be indicated with the illumination of the bottom 3 rows of LEDs, including the illumination of the top row of 4 blue LEDs. Tank levels between ¼ and ½ full shall be indicated with the illumination of the bottom 2 rows of LEDs, including the illumination of the top row of 4 amber LEDs. Tank levels between ¼ full and near empty shall be indicated with the illumination of the bottom row of 4 red LEDs only. Tank levels between near empty and empty shall be indicated by flashing the bottom row of 4 red LEDs.

Quote No: 0015791 Page 15 of 49

Smeal Fire Apparatus Co.

SO#: The master display shall have a backlit area above at the top with illuminated water icon and a backlit area at the bottom with illuminated OEM logo.

A wide-angle polycarbonate diffusion lens in front of the LEDs shall produce a 180° viewing angle. The electronic display module shall be waterproof and shock resistant being encapsulated in a urethane-based potting compound. The potted display electronics shall be integral to a chrome-plated panel-mount reflector that is secured to the apparatus panel with 4 screws installed from the inside of the panel.

All programming functions shall be accessed and performed from the front of the installed master display module with a magnet. The programming shall include manual or self-calibration for any style tank.

4" WATER TANK OVERFLOW The tank shall be equipped with a minimum of a 4" schedule 40 polypropylene overflow/ air vent pipe. The pipe shall be installed in the fill tower and extend through the tank and dump to the rear of the rear axle.

HOSE BED The hose bed shall be located above the water tank and have a minimum capacity of 30 cubic feet in accordance with the latest NFPA regulations. The inside of the hose bed shall be smooth aluminum. The hose bed shall exit at the rear of the apparatus through a single access opening. The opening shall be free of obstructions that might interfere with the deployment and loading of hose. There shall be a 1" stainless steel trim piece on the body, at the rear-bottom of the hose bed, to protect the chevron when deploying hose and shall be attached using fasteners.

The interior of the hose bed shall be painted the same body color as the upper portion of the body.

The floor of the hose bed compartment shall be constructed of Dura-Dek fiber reinforced plastic material. The flooring shall be fabricated of "T" beam protrusions in parallel connected with cross slats that are first mechanically bonded and then epoxied, forming a large sheet. The top portion of each "T" cross section shall measure 1-1/4" wide and 3/16" thick with beaded ends. The vertical portion shall be 3/8" thick, beading out at the bottom to a thickness of 1/2" and tall enough to result in an overall height of 1". The "T" sections shall be spaced 3/4" apart to allow for drainage and ventilation.

Each "T" beam shall be constructed utilizing a core of 250,000 continuous glass fiber strands that are high in resistance to tension, compression and bending. An outer sheath consisting of a continuous strand mat to prevent lineal splitting and slipping shall surround the core. The sheath shall also serve to draw the protective resin to the bar surface. Both reinforcements shall be pulled through an isophthalic polyester resin, treated with antimony trioxide for fire resistance, to form a solid length.

The flooring shall then be protected with a polyurethane coating to screen out ultraviolet rays. This bright white coating shall be baked on and shall provide a pleasing contrast when installed in the apparatus.

The hose bed shall be contain the following hose load: 300' of 2-1/2" double jacket hose Quote No: 0015791 Page 16 of 49

Smeal Fire Apparatus Co.

1000' of 5" double jacket hose HOSE BED COVER SO#: There shall be a heavy-duty 22 oz. hypalon vinyl coated nylon hose bed cover installed on the apparatus. The front edge of the cover shall be retained in a "C" channel to prevent wind from lifting it. The sides of the cover shall be attached to the sides of the hose bed utilizing hooks and bungee cord. The rear of the cover shall be attached to the body utilizing hooks and bungee cord. The cover color shall be black.

HOSE BED DIVIDER There shall be one (1) hose bed divider installed in the hose bed. The divider shall be fabricated from 1/4" smooth aluminum plate and an aluminum extrusion. The divider shall have an abraded finish and mounted on hot-dipped galvanized slide rails at the front and rear of the hose bed. Where no obstruction such as a fill tower is present, the slide rails shall allow full movement of the divider along the width of the hose bed. The hose bed divider shall have an oval shaped hand hold slot to assist in moving the divider.

This shall provide the capability for variable hose load configurations and capacities.

HOSE BED LOADING LIGHT There shall be one (1) Unity, model AG-R hose bed loading light provided on the rear of the apparatus. The light shall be a 6" round light in a chrome housing. The hose bed lighting circuit shall be deactivated when the park brake is disengaged. The light shall include a switch at the lighthead.

ALUMINUM BODY CONSTRUCTION The apparatus body shall be fabricated from 1/8" 5052-H32, smooth aluminum sheet.

The total outside width of the apparatus body shall not exceed 100 inches (2.54 meters).

The width measurement of the sidewalls shall be made from the outside wall of the two opposite sides of the body. The body shall be designed for a single axle chassis.

The complete apparatus body shall be fabricated utilizing the break and bend techniques in order to form a strong, yet flexible, uni-body structure. The body shall be constructed with holding fixtures to ensure proper dimensioning. Each apparatus body is specific in design in order to meet the unique requirements of the purchasing fire department.

The main body compartments on each side, as well as the rear center compartment if applicable, shall contain a sweep out floor design. Each compartment shall be made to the most practical dimensions in order to provide maximum storage capacity for the fire department's equipment. The door opening threshold shall be positioned lower than the compartment floor permitting easy cleaning of the compartments.

Continuous, solid welded seams shall be located at the upper front and upper rear corners of the apparatus body. The flooring of all lower, main body compartmentation shall also have solid weld seams. All door jams, on both the top and the bottom, shall be solid welded as well. Each main door jam shall consist of a double jam design; this is comparable to a double struck frame design, which provides superior strength and durability. All double door jams are to be welded together utilizing the plug weld technique. All remaining compartment walls shall be stitch welded.

The compartment floors, specifically L1 and R1, shall have a minimum of two (2) 2" x Quote No: 0015791 Page 17 of 49

Smeal Fire Apparatus Co.

SO#: 1/4" angles welded to the entire width of the compartment floor. The two (2) rear side compartments as well as the rear center compartment, if applicable, shall be welded to the rear deck support structure. This rear deck support structure is specially designed for the galvanized apparatus body substructure. A minimum of two (2) angles, which are 1/4" x 3" x 3", shall run the entire width of the body from sidewall to sidewall. Each lower, rear compartment shall be adequately stitch welded to the cross angles providing strength and durability to the entire apparatus body.

The body design shall include a "false wall" design in the lower portion of each lower, rear compartment. This "false wall" is required in order to allow for easy accessibility to the rear electrical components found in the rear tail light cluster area.

On the upper area of the apparatus body, directly above the side compartment door openings, a header is to be fabricated from smooth, aluminum sheet. This area shall be free from any body seams and shall be painted the same color as the apparatus body.

The height of the header may vary depending on the following factors: apparatus design, lettering requirements, scene lights and warning light requirements as well as various other options. A "J" channel shall be incorporated into the body design in order to provide a rain gutter to further assist in preventing excessive moisture from getting into the compartments.

There shall be one (1) ROM rollup door installed on each side body compartment face.

Each door shall be a shutter type with 34 millimeter slats that roll onto a spool at the top of the compartment. Each slat shall be equipped with nylon end shoes to assure operation without the need of constant lubrication. Each rollup door shall have a satin finish.

Each ROM rollup door shall be supplied with a full width lift bar and finger pull handle integrated into the bottom rail for easy one hand operation.

The door handles on the side body compartments of the apparatus shall be non-locking style.

REAR COMPARTMENT DOOR There shall be one (1) ROM rollup door installed on the T1 compartment face. The door shall be a shutter type with 34 millimeter slats that roll onto a spool at the top of the compartment. Each slat shall be equipped with nylon end shoes to assure operation without the need of constant lubrication. The roll-up door shall have a satin finish.

The ROM rollup door shall be supplied with a full width lift bar and finger pull handle integrated into the bottom rail for easy one hand operation.

BODY COMPARTMENT LIGHTING There shall be a total of seven (7) ROM V4 LED compartment lights installed in the body compartments. Each light shall feature solid state construction and be waterproof to IPX7 rating. The V4 LED lights shall offer 250 lumens per foot of lighting.

COMPARTMENT COATING The interior of the body compartments shall be coated with gray Line-X®. thermoplastic polyurethane coating, unless otherwise specified. The coating shall be durable enough to withstand every day abuse of equipment removal and shifting.

Quote No: 0015791 Page 18 of 49

Smeal Fire Apparatus Co.

COMPARTMENT AIR RELEASE SO#: Each compartment shall be vented to help remove trapped air when closing a compartment door. The vent shall be a rubber gasket in the area of the outboard corners of the compartment. Wiring may also be run through these areas.

COMPARTMENT DRAIN HOLES Each body compartment shall be equipped with drain holes to allow standing water to exit to underneath the apparatus.

DRIVER'S (LEFT) SIDE BODY COMPARTMENTS COMPARTMENT L1 There shall be a full height compartment located ahead of the rear wheels on the driver's side of the apparatus body. This compartment shall be designated as L1 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 58" Width: 40" Depth: 15" Upper and 26" Lower Intermediate Divide Height: 27" COMPARTMENT L2 There shall be a standard height compartment located above the rear wheels on the driver's side of the apparatus body. This compartment shall be designated as L2 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 25.5" Width: 55" Depth: 15" Upper and 0" Lower Intermediate Divide Height: 0" COMPARTMENT L3 There shall be a full height compartment located behind the rear wheels on the driver's side of the apparatus body. This compartment shall be designated as L3 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 58" Width: 32" Depth: 15" Upper and 26" Lower Intermediate Divide Height: 27" L1 Components There shall be one (1) aluminum adjustable full-depth shelf installed on the apparatus in the compartment. The shelf shall be constructed of 3/16" aluminum sheet with 2" lips.

The shelf shall be coated with abraded finish and shall be designed in such a manner as to allow liquids to readily drain when spilled.

Quote No: 0015791 Page 19 of 49

Smeal Fire Apparatus Co.

There shall be aluminum vertical strut channels welded in the compartment. There shall be two (2) struts on each side of the compartment SO#: The compartment layout shall be detailed at the pre-construction meeting.

L2 Components The compartment layout shall be detailed at the pre-construction meeting.

L3 Components There shall be one (1) aluminum adjustable full-depth shelf installed on the apparatus in the compartment. The shelf shall be constructed of 3/16" aluminum sheet with 2" lips.

The shelf shall be coated with abraded finish and shall be designed in such a manner as to allow liquids to readily drain when spilled.

There shall be aluminum vertical strut channels welded in the compartment. There shall be two (2) struts on each side of the compartment The compartment layout shall be detailed at the pre-construction meeting.

DRIVER'S SIDE REAR WHEEL WELL POSITION - WL1 There shall be a single air bottle compartment installed in the forward portion of the rear wheel well area, on the driver's side. The compartment door and hinges shall be constructed out of stainless steel material, and the frame shall be constructed out of aluminum. The door shall have a rubber gasket in order to create a 100% seal to protect the interior of the compartment. The storage compartment shall be a rotational, molded component that is assembled to the door and frame. This assembly process shall prevent the air bottle from making contact with the stainless steel frame while loading and unloading the air bottle. The door shall have a brushed stainless steel finish.

DRIVER'S SIDE REAR WHEEL WELL POSITION - WL3 There shall be a single air bottle compartment installed in the rearward portion of the rear wheel well area, on the driver's side. The compartment door and hinges shall be constructed out of stainless steel material, and the frame shall be constructed out of aluminum. The door shall have a rubber gasket in order to create a 100% seal to protect the interior of the compartment. The storage compartment shall be a rotational, molded component that is assembled to the door and frame. This assembly process shall prevent the air bottle from making contact with the stainless steel frame while loading and unloading the air bottle. The door shall have a brushed stainless steel finish.

OFFICER'S (RIGHT) SIDE BODY COMPARTMENTS COMPARTMENT R1 There shall be a lower compartment located ahead of the rear wheels on the officer's side of the apparatus body. This compartment shall be designated as R1 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 23" Width: 40" Depth: 0" Upper and 26" Lower Intermediate Divide Height: 0" Quote No: 0015791 Page 20 of 49

Smeal Fire Apparatus Co.

COMPARTMENT R2 There shall be a lower compartment located behind the rear wheels on the officer's side of the apparatus body. This compartment shall be designated as R2 within these specifications and any ensuing paperwork or drawings after contract execution.

SO#: The dimensions of the compartment shall be: Height: 23" Width: 32" Depth: 0" Upper and 26" Lower Intermediate Divide Height: 0" R1 Components The compartment layout shall be detailed at the pre-construction meeting.

R2 Components The compartment layout shall be detailed at the pre-construction meeting.

OFFICER'S SIDE REAR WHEEL WELL POSITION - WR1 There shall be a single air bottle compartment installed in the forward portion of the rear wheel well area, on the officer's side. The compartment door and hinges shall be constructed out of stainless steel material, and the frame shall be constructed out of aluminum. The door shall have a rubber gasket in order to create a 100% seal to protect the interior of the compartment. The storage compartment shall be a rotational, molded component that is assembled to the door and frame. This assembly process shall prevent the air bottle from making contact with the stainless steel frame while loading and unloading the air bottle. The door shall have a brushed stainless steel finish.

OFFICER'S SIDE REAR WHEEL WELL POSITION - WR3 There shall be a single air bottle compartment installed in the rearward portion of the rear wheel well area, on the officer's side. The compartment door and hinges shall be constructed out of stainless steel material, and the frame shall be constructed out of aluminum. The door shall have a rubber gasket in order to create a 100% seal to protect the interior of the compartment. The storage compartment shall be a rotational, molded component that is assembled to the door and frame. This assembly process shall prevent the air bottle from making contact with the stainless steel frame while loading and unloading the air bottle. The door shall have a brushed stainless steel finish.

REAR SIDE BODY COMPARTMENTS COMPARTMENT T1 There shall be a full height compartment located at the rear of the apparatus body. This compartment shall be designated as T1 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 38" Width: 41" Depth: " T1 Components Quote No: 0015791 Page 21 of 49

Smeal Fire Apparatus Co.

SO#: There shall be one (1) roll out equipment tray installed on the floor of the compartment.

The tray shall be equipped with a Hansen International drawer slide. The roller assembly shall have a rated capacity of 300 lbs. distributed load and shall have 100% extension capability. The tray shall be constructed of 3/16" aluminum sheet with 3" lips to prevent items from being shifted during transportation. The tray shall have an abraded finish and be equipped with a gas spring in order to hold the tray in either a fully extended or closed position.

The compartment layout shall be detailed at the pre-construction meeting.

GS-36 BODY SUB FRAME To assure proper body alignment and clearance, the body sub frame shall be constructed in a jig and fitted directly on the chassis. The sub frame shall be constructed of 36,000 PSI galvanized steel.

The chassis frame rails shall be fitted with fiber reinforced rubber to isolate the body frame members from direct contact with chassis frame rails.

The main body sub frame shall be constructed from steel tubing. The sub frame shall run the full length of the body and shall be spaced the same width as the chassis frame rails.

The main sub frame shall also be the integral support for the water tank. Vertical drop tubes shall be welded to the sub frame. From these vertical drop tubes shall extend cross members constructed of steel angle. These cross members shall extend out to support the compartments. Cross members shall be located at the front and rear of the body and in front and rear of the wheel well opening.

A drop frame, fabricated of steel tube and steel angles, shall support the compartment area behind the rear. The rear drop frame shall be constructed using vertical drop tubes, welded to the main sub frame. All drop frame structures shall be welded directly to the body sub frame to allow the body to be a completely separate structure from the chassis.

After fabrication the sub frame shall be hot dip galvanized for maximum protection against corrosion.

BODY MOUNTING The body sub frame shall be fastened to the chassis frame with a minimum of six (6) spring loaded body mounts. Each mount shall be configured using a two-piece bracket.

The two (2) brackets shall be fabricated of steel plates. The plates shall be galvanized to prevent any corrosion. Each mounting assembly shall utilizing two (2) plated bolts and two (2) heavy duty springs. The assembly design shall allow the body and sub frame to act as one (1) component, separate from the chassis. As the chassis frame twists under driving conditions, the spring mounting system shall limit any stress from being transferred into the body. The spring loaded body mounts shall also prevent frame side rail or body damage caused by unevenly distributed stress and strains due to load and chassis movement.

Body mountings that do not allow relief from chassis movement shall not be acceptable.

TANK MOUNTING The water tank shall rest on the sub frame cross members which are spaced as required by the tank manufacturer.

Quote No: 0015791 Page 22 of 49

Smeal Fire Apparatus Co.

SO#: The tank shall be isolated from the cross members through the use of hard rubber strips with a minimum Rockwell hardness of 60 durometer. Additionally, the tank shall be supported around the entire perimeter and captured front and rear as well as side to side to prevent the tank from shifting during vehicle operations.

Although the tank shall be designed on a free floating suspension principle, it shall be required that the tank have adequate hold down restrains to minimize movement during vehicle operations.

The tank shall be completely removable without disturbing or dismantling the apparatus structure.

WALKWAYS AND OVERLAYS All exterior surfaces designated by the manufacturer as stepping, standing, or walking areas shall be overlaid with 3003 H22 Bright Tread Plate to provide a slip resistant surface, even when the surface is wet. All interior surfaces designated by the manufacturer as stepping, standing, or walking areas shall be slip resistant when the surface is dry. The degree of slip resistance shall be in compliance with the intent of NFPA 1901.

Horizontal walkways shall have .080" aluminum tread plate overlays installed and vertical surfaces shall have .125” aluminum overlays. Overlays shall be installed that are totally insulated from the apparatus with nylon shoulder washers that extend into holes in the body. Stainless steel cap nuts shall be employed where bolt ends may damage equipment or cause injury. After the apparatus is painted and the overlays are reinstalled, they shall be additionally sealed at the edges with a caulking compound. The exterior top tread plate overlay shall be mounted flush with the outer edges of the apparatus body.

STEPPING SURFACES All steps shall have a surface area of at least 35 square inches and shall be able to withstand a load of at least 500 pounds. Steps shall be provided at any area that personnel may need to climb and shall be adequately lighted.

REAR DECK A modular bolt-on deck shall be installed on the rear of the apparatus to form a full width step area. The rear deck shall be constructed of anti-slip bright tread plate. The outside edge of the rear deck shall be flush with the rub rail that is installed on the body to maintain a uniform appearance. The depth of the rear deck shall be 13.25”. The rear deck shall be installed with sufficient support to form a sturdy, non-deflecting step area for personnel.

BODY RUB RAILS Rub rails shall be installed beneath the compartment doors to protect them from damage should the body be brushed or rubbed against another object. The rub rails shall be 3/16” aluminum channel, 2-1/2” x 1”. The rub rails shall be highly polished and then bright dip anodized.

The rub rails shall be installed on the body utilizing non-corrosive nylon spacers and Quote No: 0015791 Page 23 of 49

Smeal Fire Apparatus Co.

secured with stainless steel bolts. The outside edge of the rub rails shall be even with the fenderettes and bolt-on steps to prevent snagging.

SO#: REAR UNDERBODY TOW EYE One (1) rear tow eye shall be installed directly below the rear of the chassis frame rails, mounted to the subframe. The tow eye shall be capable of a 15,000 lb. straight pull rating.

REAR WHEEL WELLS The fenders shall be integral with the body sides and compartments with a seamless appearance. The fenders shall be fitted with bolt-in removable full circular inner liners in the wheel well area for ease of cleaning and maintenance. There shall be sufficient clearance provided in the wheel well to allow the use of tire chains when the apparatus fully loaded.

STAINLESS STEEL REAR FENDERETTES Two (2) stainless steel fenderettes shall be installed at the outboard edge of the rear wheel well area, one (1) on each side. The fenderettes shall be bolted to the apparatus body using nylon washers to space them slightly away from the body to reduce build-up of road grime. The fenderettes shall be constructed of stainless steel that has been polished to a high quality finish.

EXHAUST HEAT DEFLECTOR SHIELD There shall be a 4" heat deflector shield installed over the exhaust to aid in dissipating the heat to prevent exhaust heat from adversely affecting anything stored in the body.

FUEL TANK GAUGE ACCESS PANEL There shall be a removable panel provided in the rear compartment to allow for access to the fuel tank gauge without removing the fuel tank.

LICENSE PLATE BRACKET There shall be a license plate bracket mounted on the rear of the apparatus. A clear LED light shall be incorporated into the bracket.

TRIMRITE® STAINLESS STEEL FASTENERS TrimRite® stainless steel fasteners shall be provided for all exposed and unpainted fasteners throughout the body in locations such as overlays, pump panels, and other numerous hardware mounting locations. TrimRite® stainless is a hardenable martensitic stainless steel that provides a high level of corrosion resistance, hardness up to Rockwell C 51, good cold formability and ease of heat treatment, all of which combine to provide an alloy which has been used for many applications such as fasteners, especially self-drilling types. TrimRite® stainless are tested to salt spray standard ASTM B117, which is a 200-hour salt spray test. The OEM shall use TrimRite® stainless with an added blue patch which provides improved vibration resistance for the fastener.

Quote No: 0015791 Page 24 of 49

Smeal Fire Apparatus Co.

ADDITIONAL HARDWARE SO#: There shall be a bag of stainless steel nuts, bolts, and washers supplied with the apparatus for mounting of equipment.

FRONT BODY STEPS AND LIGHTING There shall be three (3) Cast Products folding steps located on the front of the driver's side body compartments. The folding steps shall have two large open slots to prevent the buildup of ice or mud and to provide a handhold when necessary. The steps shall have a surface area of at least 35 square inches and shall be able to withstand a load of 500 pounds.?

The steps shall be adequately lit with LED lighting. There shall be one (1) light located above the steps.

FRONT BODY STEPS AND LIGHTING There shall be three (3) Cast Products folding steps located on the front of the officer's side body compartments. The folding steps shall have two large open slots to prevent the buildup of ice or mud and to provide a handhold when necessary. The steps shall have a surface area of at least 35 square inches and shall be able to withstand a load of 500 pounds.?

The steps shall be adequately lit with LED lighting. There shall be one (1) light located above the steps.

REAR STEPS There shall be seven (7) Cast Products bolt-on steps installed on the rear of the apparatus. Each step shall have large open slots to prevent buildup of ice or mud and to provide a handhold when necessary. Steps shall be provided in the following locations:

• •

Four (4) bolt-on steps on the driver's side rear of the apparatus.

Three (3) bolt-on steps on the officer's side rear of the apparatus.

The steps shall be adequately lit with LED lighting. There shall be one (1) light located above each set of steps on the rear face of the body, for a total of two (2) lights. Each light shall be located in a manner that shall light all of the steps on its respective side.

HANDRAILS All handrails, unless otherwise stated, shall be constructed of knurled aluminum of not less than 1-1/4" in diameter. All railing shields and brackets shall be chrome plated, and shall be bolted to the body with stainless steel bolts. The lower bracket on all vertical handrails shall have a drain hole drilled in it at the lowest point.

The following handrails shall be provided on the apparatus: There shall be a handrail installed forward on the top of the body, on the driver's side.

There shall be two (2) vertical handrails installed on the rear of the apparatus, one (1) on the driver's side and one (1) on the officer's side.

There shall be a horizontal handrail installed below the hose bed.

Quote No: 0015791 Page 25 of 49

Smeal Fire Apparatus Co.

GROUND LADDER STORAGE SO#: The ground ladders shall be stored above the low officer's side compartments with brackets that provide a quick method of removing and reloading the ladders. A quick release shall allow personnel to loosen and unhook the retaining strap in order to remove the ladders, a ratchet style mechanism shall securely and easily fasten the ladders back into place. The bracket shall allow a sectional ladder to still be clamped into position when the roof ladder has been removed.

The following ground ladders shall be supplied with the apparatus: One (1) Duo Safety, model 900-A, 24' two section aluminum extension ladder shall be provided. The ladder shall be constructed with 6061-T6 aluminum alloy and shall have a 750 pound duty rating. The ladder shall have a closed length of 14' 2.75".

One (1) Duo Safety, model 775-A, 14' aluminum roof ladder shall be provided. The ladder shall have a 750 pound duty rating and aluminum roof hooks that fold for storage.

One (1) Duo Safety, model 585-A, 10' folding ladder shall be provided. The ladder shall have a 300 pound duty rating and Duo Safety ladder shoes for slip resistance.

PIKE POLE STORAGE There shall be two (2) aluminum tubes for the storage of pike poles installed above the low officer's side compartments. The poles shall be mounted on the catwalk, below the ladders.

The following pike poles shall be supplied with this location on the apparatus: One (1) Akron Brass, model UL-6, 6' fiberglass pike pole shall be provided. The light weight heavy duty pole shall be constructed of one and one quarter inch round fiberglass with a rubber bumper butt style handle.

One (1) Akron Brass, model UT-8, 8' fiberglass pike pole shall be provided. The light weight heavy duty pole shall be constructed of one and one quarter inch round fiberglass with a rubber bumper butt style handle.

HARD SUCTION HOSE STORAGE There shall be two (2) hard suction enclosed hose tray located inside the body, driver's side of the water tank, each with the capacity to store one (1) 10' section of hard suction hose. Access to the hard suction hose shall be from the rear of the apparatus through a single hinged tread plate door.

HARD SUCTION HOSES There shall be two (2) Firequip Maxi-Flex PVC 6” x 10’ sections of hard suction hose provided.

HARD SUCTION HOSE STORAGE There shall be a hard suction hose "V" trough located above the officer's side low compartments with the capacity to store one (1) 10' section of hard suction hose. The trough shall be fabricated of abraded aluminum plate. Velcro straps shall be supplied to hold the hard suction hose secure.

Quote No: 0015791 Page 26 of 49

Smeal Fire Apparatus Co.

HARD SUCTION HOSE SO#: There shall be one (1) Firequip Maxi-Flex PVC 6” x 10’ section of hard suction hose provided.

The wheel chocks shall be stored in locations that are easily accessible under the front of the body on the driver's side of the apparatus.

WHEEL CHOCKS There shall be one (1) pair of Cast Products model TMC1008-4 wheel chocks provided with the apparatus. The wheel chocks shall be mounted in Cast Products model TMC 1010 mounting brackets.

INDEPENDENT ALUMINUM SIDE MOUNT PUMP MODULE The pump module shall be a side mount design. The pump module shall be fabricated from 1/8" 5052-H32, smooth aluminum sheet. The module shall be fabricated as an individual unit, independent from the body. The module shall be fabricated utilizing the break and bend technique in order to form a strong, yet flexible, structure. The pump module shall be fabricated using precision holding fixtures to ensure proper dimensions and all attachment points shall be heavily reinforced.

PUMP COMPARTMENT LIGHTS The pump compartment shall be equipped with two (2), 9" On-Scene Night Axe LED compartment lights. The lights shall be rated at 100,000 hours of service. The light shall be waterproof and magnesium chloride resistant. The light shall be enclosed in tough 5/8" Lexan tube. Multi-clip attachments shall allow for easy installation.

DRIVER'S SIDE RUNNING BOARD A modular bolt-on running board shall be installed on the driver's side of the pump module. The running board shall be constructed of anti-slip tread plate. The outside edge of the running board shall be flush with the rub rail that is installed on the body to maintain a uniform appearance. The running board shall be installed with sufficient support to form a sturdy, non-deflecting step area for personnel.

OFFICER'S SIDE RUNNING BOARD A modular bolt-on running board shall be installed on the officer's side of the pump module. The running board shall be constructed of anti-slip tread plate. The outside edge of the running board shall be flush with the rub rail that is installed on the body to maintain a uniform appearance. The running board shall be installed with sufficient support to form a sturdy, non-deflecting step area for personnel.

DUNNAGE COMPARTMENT There shall be a dunnage compartment located above the pump module. The dunnage compartment floor shall be constructed of tread plate.

FRONT PUMP ACCESS PANEL There shall be a painted aluminum access panel provided on the front of the pump Quote No: 0015791 Page 27 of 49

Smeal Fire Apparatus Co.

compartment. The panel shall be of the single pan design and shall be secured utilizing stainless steel fasteners.

SO#: OFFICER'S SIDE PUMP ACCESS PANEL There shall be a tread plate door above the officer's side pump panel to allow access to the pump compartment. The vertically hinged panel shall be of the single pan design and shall be positively latched in the closed position utilizing a push button latch. A gas strut shall be provided on the door. An aluminum sill protector shall be installed on the bottom of the door opening to protect the paint from chipping and scratching. The door shall be wired into the door open warning light circuit.

CONTROL PANEL The driver's side of the pump enclosure shall be divided into two sections. The lower section shall be where all valve controls, the primer control, the discharge relief valve controls (pilot valve), and other mechanical controls are located. This surface shall be referred to as the "control panel".

All valve controls shall be the self-locking type, activated by either direct control or with a direct linkage utilizing friction locking bell cranks and universal ball swivels. The primary valve handles shall have color coded tags installed in a recessed area to clearly denote the purpose of each control.

INSTRUMENT PANEL The surface above the control panel shall contain all instruments, gauges, test fittings, and optional controls. This surface shall be referred to as the "instrument panel". The instrument panel shall be independent and hinged and latched so that it may be opened.

All instruments, gauges, and other equipment shall be installed with sufficient slack in any cabling, tubing, or plumbing to allow the panel to swivel to the fully open position.

The instrument and gauge panel shall be vertically hinged "swing out" to provide access for service.

OFFICER'S SIDE PUMP PANEL A single panel shall be installed on the officer's side of the pump enclosure. This shall be the area where any officer's side discharges, inlets, steamers, and other pump associated equipment are located. This panel shall be easily removable and held in place with quick release push latches. It shall be fully removable for pump and plumbing access without the need to use hand tools. Any electrical equipment that may be installed shall be equipped with connectors so they may be easily separated from the opening created when the below described front access panel is removed.

PANEL SURFACES The control panel, instrument panel, and officer's side pump panel shall be coated with black Line-X® for maximum resistance to abrasion and to minimize glare. The material shall be capable of withstanding the effects of extreme temperatures and weather.

GARNISH RING BEZEL ASSEMBLIES Quote No: 0015791 Page 28 of 49

Smeal Fire Apparatus Co.

Innovative Controls intake and/or discharge garnish rings shall be installed to the apparatus with mounting bolts. These bezel assemblies shall be used to identify intake and/or discharge ports with color and verbiage. The garnish rings shall be designed and manufactured to withstand the specified apparatus service environment and shall be backed by a warranty equal to that of the exterior paint and finish. The specified assemblies shall feature a chrome-plated panel-mount bezel with durable UV resistant polycarbonate inserts. These UV resistant polycarbonate graphic inserts shall be sub surface screen printed to eliminate the possibility of wear and protect the inks from fading. All insert labels shall be backed with 3M permanent adhesive (200MP), which meets UL969 and NFPA standards.

SO#: VERBIAGE TAG BEZEL ASSEMBLIES Innovative Controls verbiage tag bezels shall be installed. The bezel assemblies will be used to identify apparatus components. These tags shall be designed and manufactured to withstand the specified apparatus service environment and shall be backed by a warranty equal to that of the exterior paint and finish. The verbiage tag bezel assemblies shall include a chrome-plated panel-mount bezel with durable easy-to-read UV resistant polycarbonate inserts featuring the specified verbiage and color coding. These UV resistant polycarbonate verbiage and color inserts shall be sub-surface screen printed to eliminate the possibility of wear and protect the inks from fading. Both the insert labels and bezel shall be backed with 3M permanent adhesive (200MP), which meets UL969 and NFPA standards.

SAFETY MESSAGE BEZEL ASSEMBLIES Innovative Controls safety message bezels shall be installed. The bezel assemblies will be used to identify, instruct, or warn the operators. These tags shall be designed and manufactured to withstand the specified apparatus service environment and shall be backed by a warranty equal to that of the exterior paint and finish. The safety message bezel assemblies shall include a chrome-plated panel-mount bezel with durable easy-to read UV resistant polycarbonate inserts featuring ANSI safety standard graphics or custom graphics. These UV resistant polycarbonate graphic inserts shall be sub-surface screen printed to eliminate the possibility of wear and protect the inks from fading. Both the graphic insert labels and bezel shall be backed with 3M permanent adhesive (200MP), which meets UL969 and NFPA standards.

PUMP PANEL LIGHTING The pump operator's control panel and the officer's side pump panel shall each be illuminated by On-Scene LED Night Axe lighting. The pump panel lights shall become energized upon setting the parking brake so the gauge information provided may be consulted at any time the apparatus is parked. A stainless steel shield shall be installed over the pump panel lights to further protect them from the elements and to act as a reflector for additional illumination.

The pump panel lighting shall become energized automatically upon setting the park brake so the gauge information may be consulted at any time the apparatus is parked.

MIDSHIP MOUNT FIRE PUMP The pump shall be a Waterous CXVC20 1250 U.S. GPM (5000 LPM) fire pump. The pump shall be a single stage centrifugal class "A" rated fire pump, designed specifically for the fire service.

Quote No: 0015791 Page 29 of 49

Smeal Fire Apparatus Co.

SO#: The pump body shall be cast as two (2) vertically split pieces. The body shall be made of high tensile, close-grained gray iron with a minimum tensile strength of 40,000 PSI.

IMPELLERS The pump impellers shall be bronze, specifically designed for the fire service and accurately balanced for vibration free running. The stripping edges shall be located on opposite sides of the impellers to reduce shaft deflection.

The impeller shaft shall be stainless steel, accurately ground to size and supported at each end by oil or grease lubricated anti-friction ball bearings for rigid, precise support.

The bearings used on the impeller shaft shall be automotive type bearings, easily cross referenced and readily available at normal parts or bearing stores.

IMPELLER WEAR RINGS The pump shall be equipped with replaceable bronze wear rings for increased pump life and minimum maintenance cost. The wear rings shall be designed to fit into a groove in the face of the impeller hubs forming a labyrinth that, as the clearance increases with age, directs water from the discharge side in several directions eventually exiting outward, away from the eye of the impeller hub.

LUBRICATION SYSTEM An internal lubrication system shall deliver lubricant directly to the drive chain. This unique design shall eliminate the need for an external lubrication pump and auxiliary cooling. Oil shall be supplied with the lubrication system.

PUMP TRANSMISSION The pump shall have a Waterous model C20 series transmission. The housing of the transmission shall be constructed of high strength, three piece, horizontally split aluminum. The drive line shafts shall be made from alloy steel forgings, hardened and ground to a size 2.350 inch 46 tooth involute spline. The drive and driven sprockets shall be made of steel and shall be hardened and have ground bores. The drive chain shall be a Morse HV™ high strength involute form chain. Bearings shall be deep groove, anti friction ball bearings and shall give support and proper alignment to the impeller shaft assembly. Bearings shall be oil splash lubricated, completely separated from the water being pumped, and protected by a V-ring and oil seal. An internal lubrication system shall deliver lubricant directly to the drive chain. This unique design eliminates the need for an external lubrication pump and auxiliary cooling. The pump and transmission shall be easily separable. A two-piece shaft shall be splined allowing for individual repair of either the pump or transmission, to keep down time to a minimum. All drive line components shall have a torque rating equal to or greater than the final net engine torque.

MECHANICAL SEALS The pump shall be equipped with self-adjusting, maintenance free mechanical shaft seals that shall not require manual adjustment. These seals shall be designed in a manner such that they shall remain functional enough to permit continued use of the pump in the unlikely event of a seal failure.

Quote No: 0015791 Page 30 of 49

Smeal Fire Apparatus Co.

ALLOY ANODE There shall be one (1) OEM supplied alloy anode provided with the fire pump. The anode shall aid in preventing galvanic corrosion within the water pump and shall be easily replaceable. The anodes shall be installed as follows:

The anode shall be provided in the intake manifold of the fire pump.

The pump shall be rated at 1250 gallons per minute.

FIRE PUMP MOUNTING SO#: The fire pump shall be mounted within a separate body module that is not directly connected to the apparatus body.

The pump shall be frame mounted; therefore minimizing the likelihood of the pump casing cracking should the apparatus be involved in a collision.

The pump module shall be mounted to the frame in four (4) locations and shall be reinforced appropriately in order to carry the expected load for the life of the apparatus.

PUMP SHIFT The pump shift actuating mechanism shall be air operated from a valve in the cab identified as "PUMP SHIFT". Full instructions for shifting the pump shall be inscribed on the valve plate.

There shall be two (2) green pump system shift indicator lights in the chassis cab. The first light shall become energized when the pump has completed its shift into pump gear and shall be labeled "Pump Engaged". The second light shall become energized when the chassis parking brake has been set and when the pump and the chassis transmissions have been shifted completely into the correct gears for pumping, this light shall be labeled "OK to Pump".

There shall be one (1) green pump system shift indicator light located on the operator's panel. This light shall only become engaged when the chassis parking brake has been set and when the pump and the chassis transmissions have been completely shifted into the correct gears. The light shall be located adjacent to the throttle control and shall be labeled "Warning: Do Not Open Throttle Unless Light Is On".

PRESSURE GOVERNOR There shall be a Fire Research Pump Boss 400 pressure governor and monitoring display kit installed. The kit shall include a control module, intake pressure sensor, discharge pressure sensor, and cables. The control module case shall be waterproof and have dimensions not to exceed 6 3/4" high by 4 5/8" wide by 1 1/2" deep. The control knob shall be 2" in diameter with no mechanical stops, have a serrated grip, and a red idle push button in the center. It shall not extend more than 1 3/4" from the front of the control module. Inputs for monitored information shall be from a J1939 data bus or independent sensors. Outputs for engine control shall be on the J1939 data bus or engine specific wiring. Inputs to the control module from the pump discharge and intake pressure sensors shall be electrical.

The following continuous displays shall be provided: Quote No: 0015791 Page 31 of 49

Smeal Fire Apparatus Co.

SO#:

• • • • • • • • •

Engine RPM; shown with four daylight bright LED digits more than 1/2" high Check engine and stop engine warning LEDs Oil pressure; shown on a dual color (green/red) LED bar graph display Engine coolant temperature; shown on a dual color (green/red) LED bar graph display Transmission Temperature: shown on a dual color (green/red) LED bar graph display Battery voltage; shown on a dual color (green/red) LED bar graph display Pressure and RPM operating mode LEDs Pressure / RPM setting; shown on a dot matrix message display Throttle ready LED The dot-matrix message display shall show diagnostic and warning messages as they occur. It shall show monitored apparatus information, stored data, and program options when selected by the operator. All LED intensity shall be automatically adjusted for day and night time operation.

The program shall store the accumulated operating hours for the pump and engine to be displayed with the push of a button. The kit shall monitor inputs and support audible and visual warning alarms for the following conditions:

• • • • • • • •

High Battery Voltage Low Battery Voltage (Engine Off) Low Battery Voltage (Engine Running) High Transmission Temperature Low Engine Oil Pressure High Engine Coolant Temperature Out of Water (visual alarm only) No Engine Response (visual alarm only) The program features shall be accessed via push buttons located on the front of the control module. There shall be a USB port located at the rear of the control module to upload future firmware enhancements.

The governor shall operate in two control modes, pressure and RPM. No discharge pressure or engine RPM variation shall occur when switching between modes. A throttle ready LED shall light when the interlock signal is recognized. The governor shall start in pressure mode and set the engine RPM to idle. In pressure mode the governor shall automatically regulate the discharge pressure at the level set by the operator. In RPM mode the governor shall maintain the engine RPM at the level set by the operator except in the event of a discharge pressure increase. The governor shall limit a discharge pressure increase in RPM mode to a maximum of 30 psi. Other safety features shall include recognition of no water conditions with an automatic programmed response and a push button to return the engine to idle.

An interlock system shall be provided to prevent advancement of the engine speed at the pump operator’s panel unless the apparatus has “Throttle Ready” indication.

The pressure governor and monitoring pressure display shall be programmed to interface with a specific engine.

INTAKE RELIEF VALVE There shall be an Elkhart Brass intake relief valve installed on the suction side of the pump. The valve shall be the preset type, adjustable from 75 to 250 PSI, and shall be designed to prevent vibration from altering the setting. The relief outlet shall be directed Quote No: 0015791 Page 32 of 49

Smeal Fire Apparatus Co.

below the pump with the discharge terminating in a 2-1/2" male NST connection. The discharge shall be away from the pump operator and labeled "Do Not Cap".

SO#: PUMP PRIMING SYSTEM There shall be a Waterous, model VPO/VPOS priming pump included with the pump.

The priming pump shall be an electrically driven rotary vane pump mounted firmly within the pump area. The pump shall be controlled from the pump operator's panel. An indicator light on the pump panel shall show when the primer motor is engaged. The pump shall be capable of creating suction and discharging water from a lift of 10 feet through 20 feet of suction hose of the appropriate size, in not more than 30 seconds starting with the pump dry. It shall be capable of developing a vacuum of 22 inches at an altitude of up to 1000 feet.

There shall be a Waterous model VAP vacuum activated priming valve supplied with the pump. The valve shall open automatically when the priming system is activated. The valve shall be installed on the pump or mounted remotely.

MASTER DRAIN VALVE A Trident manifold drain valve assembly shall be supplied. This drain shall provide the capability to drain the entire pump by turning a single control. The valve assembly shall consist of a stainless steel plate and shaft in a bronze body with multiple ports. The drain valve control shall be mounted on the driver's side pump panel and labeled "Master Drain".

PUMP PRIMED BLACK BY PUMP MANUFACTURER The pump shall be primed black by the pump manufacturer.

The steamers shall be unpainted and any inlets shall be the same color as they arrived from the valve manufacturer.

PUMP AND ENGINE COOLING SYSTEM There shall be a pump and engine cooling system provided on the apparatus. The cooling system shall keep the engine cool when running for long periods of time and the pump cool during long periods of pumping when water is not being discharged. The cooling system shall also be setup in a way that the cooling system lines can be easily drained through the master pump drain.

The cooling system lines shall consist of high-pressure, high-temperature 3/8" (inside diameter) abraded rubber hose. The engine cooling lines shall be installed with one (1) line going from the discharge side of the water pump through an Innovative Controls, model 3004204-2-2, 3/8" in-line quarter turn ball valve assembly and continuing on to the chassis heat exchanger. The return line from the heat exchanger shall then run into the suction side of the pump. The pump cooling lines shall be installed with one (1) line going from the discharge side of the water pump through an Innovative Controls, model 3004204-2-2, 3/8" in-line quarter-turn ball valve assembly up to the water tank. At the water tank, the pump cooling line shall be plumbed into a 3/8" check valve on the "Tank Fill" valve. The check valve shall prevent tank water from back flowing into the pump when the cooling system is not in use. A return line from the water tank shall be plumbed into the water pump.

Quote No: 0015791 Page 33 of 49

Smeal Fire Apparatus Co.

SO#: The engine cooling system valve shall be controlled on the operator's panel, and shall be clearly labeled, "Engine Cooler".

The pump cooling system valve shall be controlled on operators panel, and shall be clearly labeled, "Pump Cooler".

PLUMBING MANIFOLD The plumbing manifold shall consist of the inlet side manifold and the discharge side manifold. Galvanized Victaulic couplings shall be used wherever possible for ease of maintenance and superior corrosion protection.

The inlet side of the plumbing manifold shall utilize schedule 10, 304 grade stainless steel tubing and preformed elbows for inlets that are larger than 3”. Side auxiliary inlets that are 3” or smaller shall utilize schedule 40, 304 grade stainless steel threaded tubing and preformed elbows. The inlet manifold shall thread into the pump auxiliary inlet ports and each inlet valve shall thread onto the inlet manifold.

The discharge side of the plumbing manifold shall utilize schedule 40, 304 grade stainless steel tubing and preformed elbows to ensure the quality of the manifold where welds are required. The discharge manifold shall connect to the pump discharge ports using ½” stainless steel flanges that shall be machined to seat an O-ring to ensure a leak proof seal. Each discharge shall derive from a port on the manifold assembly connected to a discharge valve with 1/2” 304 grade stainless steel flanges. Discharges that terminate in a location other than the pump module (i.e. rear discharges) that do not require welding shall utilize a combination of high pressure flex hose and schedule 10, 304 grade stainless steel tubing to allow flexibility between the body and the pump module.

INNOVATIVE CONTROLS DISCHARGE GAUGES - 2-1/2" - 0-400PSI The discharge gauges on the apparatus shall be 2 ½” (63mm) diameter Innovative Controls pressure gauges. The gauges shall have a one-piece die-cast brass case that integrates the valve stem connection, movement support, and bourdon tube support into a single unit that eliminates distortion and leakage. Clear scratch resistant molded lenses shall be used to ensure distortion-free viewing and they shall be sealed to the gauge by being trapped together with a profile gasket by a crimped stainless steel bezel.

The gauges shall be filled with a synthetic mixture to dampen shock and vibration, lubricate the internal mechanisms, prevent lens condensation and ensure proper operation from –40°F to +160°F.

The gauges shall exceed ASME B40.100 Grade B requirements with an accuracy of +/ 1.5% full scale and include a size appropriate phosphorous bronze bourdon tube with a reinforced lap joint and large tube base to increase the tube life and gauge accuracy.

Highly-polished stainless steel bezels shall be provided to prevent corrosion and protect lenses and gauge cases. The gauges shall be installed into decorative chrome-plated mounting bezels that incorporate valve identifying verbiage and/or color labels.

The gauges shall display a range from 0 to 400 psi and shall have an orange tip on the pointer.

Quote No: 0015791 Page 34 of 49

Smeal Fire Apparatus Co.

MASTER PRESSURE CENTER ASSEMBLY SO#: The master gauges shall be installed on the pump panel no more than 6 inches apart in an integrated master pressure assembly that includes the two (2) master gauges and the test port manifold.

The master intake and master discharge gauges shall be 4” (101mm) diameter Innovative Controls pressure gauges. Each gauge shall have a one-piece die-cast brass case that integrates the valve stem connection, movement support, and bourdon tube support into a single unit that eliminates distortion and leakage. A clear scratch resistant molded lens shall be used to ensure distortion-free viewing and it shall be sealed to the gauge by being trapped together with a profile gasket by a crimped stainless steel bezel.

The gauge shall be filled with a synthetic mixture to dampen shock and vibration, lubricate the internal mechanisms, prevent lens condensation and ensure proper operation from –40°F to +160°F.

Each gauge shall exceed ASME B40.100 Grade B requirements with an accuracy of +/ 1% full scale and include a size appropriate phosphorous bronze bourdon tube with a reinforced lap joint and large tube base to increase the tube life and gauge accuracy. A highly-polished stainless steel bezel shall be provided to prevent corrosion and protect the lens and gauge case.

The two (2) master gauges shall be installed into a decorative chrome-plated zinc mounting bezel that also incorporates a test port manifold and a graphic overlay that identifies the master intake and discharge gauges, the vacuum test port, and the pressure test port. The test port manifold is solid cast brass with chrome-plated plugs.

The gauge on the left shall be the master pump intake gauge and display a range from -30 to 400 psi with black graphics on a white background. The gauge on the right shall be the master pump discharge gauge and display a range from 0 to 400 psi with burgundy graphics on a white background.

The non-Storz discharge and intake fittings provided on this apparatus shall be South Park Corp. Brand. The adapter/cap/plug fittings shall be manufactured from high quality brass that shall be polished to remove manufacturing irregularities with a chrome finish applied to the polished surface.

The Storz discharge and intake fittings provided on this apparatus shall be Task Force Tips Brand. For corrosion resistance, the adapter shall be constructed of hard coat anodized aluminum alloy and include a polymer bearing ring for prevention of galvanic corrosion.

The inlets shall terminate with NST swivels, and the discharges shall terminate with NST male threads.

DISCHARGE, PRE-CONNECT, AND INTAKE DRAINS There shall be a Innovative Controls 3/4" quarter turn drain valve included on each discharge, gated intake, and steamer valve (if applicable). There shall be a side stem, long stroke chrome plated lift handle provided on the drain valve to facilitate use with a gloved hand. The drain valve shall a verbiage tag that angles upward so that it can easily be seen and rear by the operator before opening. The drain valve shall be located just above the running board and below the pump panel to reduce clutter in the pump panel area. The drain valve shall be connected to the valve with flexible hose that is routed in Quote No: 0015791 Page 35 of 49

Smeal Fire Apparatus Co.

SO#: such a manner as to assure complete drainage to below the apparatus. A matching color coded bezel shall be included.

2" TANK FILL There shall be a 2" tank fill plumbed from the pump to the tank. Installation shall be completed with 2" Class 1 rubber hose and stainless steel hose couplings.

An Akron Brass, model 8820, 2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a self-locking ball feature using an automatic friction lock design and specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1 manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

4" TANK-TO-PUMP There shall be a 4" tank-to-pump plumbed with a Class 1 flexible hose from the tank to the suction side of the pump. There shall be an Akron Brass, model 8830, 3" Swing Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a self-locking ball feature using an automatic friction lock design and specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall also include a necessary B3-SH pump flange adapter, which shall be specifically used for the tank-to-pump line to properly adjust the plumbing based on the pitch of the pump. The valve shall carry a ten (10) year warranty by the valve manufacturer.

There shall be a check valve between the pump suction and the booster tank valve. The check valve shall eliminate back flow into the water tank when the pump is connected to a pressurized source.

The valve shall be actuated by an Akron Brass, model R1 manual actuator. The manual actuator shall be controlled by an Innovative Controls push/pull T-handle.

The tank plumbing valves and controllers shall have the OEM Standard label package unless stated otherwise. The Pump-to-Tank Fill shall be labeled "TANK FILL" and shall have a Black label color. The Tank-To-Pump shall be labeled "TANK TO PUMP" and shall have a Navy Blue label color.

6" DRIVER SIDE STEAMER INLET There shall be a 6" steamer inlet located on the driver's side of the pump module. The suction fittings shall include a removable die-cast screen to provide cathodic protection for the pump thus reducing corrosion. A short steamer barrel shall be installed to Quote No: 0015791 Page 36 of 49

Smeal Fire Apparatus Co.

SO#: accommodate an intake valve without exceeding the legal overall body width. The intake shall terminate MNST thread.

There shall be one (1) South Park, model LHC26P14AC, 6" NST long handle steamer cap provided.

2-1/2" DRIVER'S SIDE INLET There shall be a 2-1/2" gated inlet, with 2-1/2" plumbing, provided on the driver's side of the pump module. The inlet shall be fully recessed behind the panel in order to keep the valve protected from the elements.

An Akron Brass, model 8825, 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model TSC manual actuator installed directly on the valve. The handle shall allow the valve to be controlled directly at the valve.

There shall be one (1) South Park, model HPC3008AC, 2 1/2" NST plug with chain provided.

6" OFFICER SIDE STEAMER INLET There shall be a 6" steamer inlet located on the officer's side of the pump module. The suction fittings shall include a removable die-cast screen to provide cathodic protection for the pump thus reducing corrosion. A short steamer barrel shall be installed to accommodate an intake valve without exceeding the legal overall body width. The intake shall terminate MNST thread.

There shall be one (1) South Park, model LHC26P14AC, 6" NST long handle steamer cap provided.

All intakes shall have the OEM Standard label package unless stated otherwise. All intake labels shall be burgundy in color. Specific verbiage on each intake label tag shall be determined at the pre-construction meeting.

2-1/2" DRIVER'S SIDE DISCHARGE There shall be a 2-1/2" discharge, with 2-1/2" plumbing, located on the driver's side of the pump compartment. The discharge shall terminate MNST.

An Akron Brass model 8625 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by Quote No: 0015791 Page 37 of 49

Smeal Fire Apparatus Co.

the valve manufacturer.

SO#: The valve shall be actuated by an Akron Brass rack and sector actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park, model SE393010AC, 2-1/2" Female NST swivel rocker lug x 2-1/2" Male NST 30º elbow adapter provided.

There shall be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

2-1/2" DRIVER'S SIDE DISCHARGE There shall be a 2-1/2" discharge, with 2-1/2" plumbing, located on the driver's side of the pump compartment. The discharge shall terminate MNST.

An Akron Brass model 8625 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass rack and sector actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park, model SE393010AC, 2-1/2" Female NST swivel rocker lug x 2-1/2" Male NST 30º elbow adapter provided.

There shall be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

2-1/2" OFFICER'S SIDE DISCHARGE There shall be a 2-1/2" discharge, with 2-1/2" plumbing, located on the officer's side of the pump compartment. The discharge shall terminate MNST.

An Akron Brass, model 8825, 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

Quote No: 0015791 Page 38 of 49

Smeal Fire Apparatus Co.

SO#: The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park, model SE393010AC, 2-1/2" Female NST swivel rocker lug x 2-1/2" Male NST 30º elbow adapter provided.

There shall be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

3" OFFICER-SIDE DISCHARGE There shall be a 3" discharge, with 3" plumbing, located on the officer's side of the pump compartment. The discharge shall terminate MNST.

An Akron Brass, model 8830, 3" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The actuator shall include an Akron Brass, model 7875, Slo-Cloz™ to control the opening and closing speed of the valve to minimize the effects of water hammer.

The valve actuator shall be controlled by an Elkhart Brass, model RC-10, handwheel valve controller. The 5" cast aluminum handwheel shall be connected to the remote mounted valve. The actuator housing and push-rod shall be constructed of light weight extruded aluminum. A precision needle thrust bearing and hardened thrust washers shall assure smooth, efficient operation and accurate flow and pressure control capability.

Opening and closing speed shall comply with the current NFPA standard to minimize effects of water hammer.

A valve position indicator shall show the position of the ball valve as per NFPA 1901. The valve position indicator shall provide the pump operator with the status of the valve at a glance. Red shall mean fully closed; Green shall mean fully opened; Yellow shall indicate a gated position. LED lamps shall provide a reliable signal with a wide viewing angle even in bright sun light. Reliable solid state valve position sensors shall be water and lubricant resistant. The integrated circuit board and lamp sockets shall be completely encased in epoxy for total protection from the elements.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) Task Force Tips model #AH3SP-NL 30 degree elbow provided.

The elbow shall be configured with a 4" swivel Storz coupling and a 3" female NH swivel rocker lug coupling.

Quote No: 0015791 Page 39 of 49

Smeal Fire Apparatus Co.

SO#: There shall also be one (1) Task Force Tips model A01SP 4" Storz blind cap with lanyard provided.

2-1/2" DRIVER'S SIDE REAR DISCHARGE There shall be a 2-1/2" discharge, with 2-1/2" plumbing, located on the driver's side rear of the apparatus. The discharge shall terminate MNST.

An Akron Brass, model 8825, 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park, model SE393010AC, 2-1/2" Female NST swivel rocker lug x 2-1/2" Male NST 30º elbow adapter provided.

There shall be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

CROSSLAY CONFIGURATION There shall be two (2) 1-1/2" crosslay pre-connects located above the pump panel.

Class1 high-pressure flex hose with stainless steel couplings shall be used in the plumbing.

A Trident 90º swivel elbow shall be utilized to keep the hose from kinking when pulled from either side of the apparatus. The swivel for each crosslay shall be located outboard for ease of making connections while changing hose.

The pre-connect hose beds shall be sized to accommodate the following hose load: The interior of the pre-connect hose bed shall have a maintenance free abraded finish.

The floor of the preconnect area shall be covered with Dura-Dek fiber reinforced material. The Dura-Dek shall have "T" beams in parallel connected with cross slats that are first mechanically bonded and then epoxied. The "T" sections shall be spaced 3/4" apart to allow for drainage and ventilation.

Stainless steel rollers shall be provided at each end of the crosslay hose bed to facilitate deployment of hose. Vertical rollers shall be installed on each side of the hose bed opening, and a horizontal roller shall be installed under the opening.

Quote No: 0015791 Page 40 of 49

Smeal Fire Apparatus Co.

There shall be one (1) divider in the crosslay area. The divider shall be fabricated of 3/16" aluminum and be mounted in a channel on each end for adjustability. The divider shall have a maintenance free abraded finish.

SO#: There shall be a heavy duty 22 oz. hypalon vinyl coated nylon cover located over the top and on each end of the pre-connected crosslays. The top of the cover shall be connected to the top-forward portion of the crosslays through a C-Rail channel and shall attach on the top-rear portion using Velcro. The bottom of the end covers shall be connected using footman loop and J-Hooks with an adjustable buckle. The cover color shall be black.

The end covers of the crosslays shall be incorporated with the top cover.

1-1/2" PRECONNECT There shall be a 1-1/2" preconnect with 2" plumbing. The preconnect shall terminate out a swivel MNST.

The 1-1/2" crosslay pre-connect shall have a capacity of 200' of 1-3/4" double jacket fire hose stored in a single stack.

An Akron Brass, model 8820, 2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

The discharge shall be designated as a pre-connect and no cap and chain shall be supplied.

1-1/2" PRECONNECT There shall be a 1-1/2" preconnect with 2" plumbing. The preconnect shall terminate out a swivel MNST.

The 1-1/2" crosslay pre-connect shall have a capacity of 200' of 1-3/4" double jacket fire hose stored in a single stack.

An Akron Brass, model 8820, 2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

Quote No: 0015791 Page 41 of 49

Smeal Fire Apparatus Co.

SO#: The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

The discharge shall be designated as a pre-connect and no cap and chain shall be supplied.

All discharges shall have the OEM Standard label package unless stated otherwise.

Each discharge label shall be a unique color. Specific verbiage and colors on each discharge label tag shall be determined at the pre-construction meeting.

ELECTRICAL SYSTEM Wiring harnesses shall be the automotive type, engineered specifically for the builder's apparatus, and shall meet the following criteria. Under no circumstances shall diodes, resistors, or fusible links be located within the wiring harness. All such components shall be located in an easy to access wiring junction box or the main circuit breaker area. All wiring shall meet white book, baseline advanced design transit coach specification and Society of Automotive Engineers recommended practices. It shall be stranded copper wire core with cross linked polyethylene insulation complying with SAE specification J1128. Each wire shall be hot stamp function coded every three inches starting one inch from the end and continuing throughout the entire harness. In addition to function coding, each wire shall be number, color, and gauge coded.

Wire harnesses shall be wrapped with a high abrasion and chemical resistant thermoplastic polyester elastomer coated polyester yarn for braiding constructions of electrical wiring systems. The braid yarn shall have a minimum tensile strength of 15 lbs.

before breaking and have a maximum of 20% elongation before breaking. Temperature properties for the yarn shall range from a minimum 280°F (138°C) service temperature to a maximum -112°F (-80°C) brittleness temperature with a cold flex tolerance of at least -49°F (-45°C).

Harnesses shall be modular in design; a main harness system subdivided into several smaller sub-harnesses. The harness subsections shall be connected using Deutsch branded, heavy duty, environmentally sealed, connectors with silicone seals and a rear insertion/removal contact system. For isolation of electrical "zones" the harness subsections shall consist of a main harness, a pump harness with a separate pump gauge panel harness, a driver's side body harness with a separate driver's side compartment harness, a officer's side body harness with a separate officer's side compartment harness, and a rear body harness with two separate rear compartment harnesses.

The main harness and three body harnesses shall interconnect at a central, easy to reach location and their connectors shall not be obstructed by other harnesses or fuel/air lines. In addition, the main and body harness connectors shall be color coded for ease of identification with their respective colors noted on the accompanying electrical diagrams.

Where connectors are not provided by the electrical component manufacturer, all 12 volt lights and other electrical components (excluding rocker and toggle switches) shall connect to the harnesses using Deutsch brand connectors; butt connectors are considered unacceptable.

Quote No: 0015791 Page 42 of 49

Smeal Fire Apparatus Co.

SO#: All Deutsch connectors shall meet the following criteria:

• • • • •

All connectors shall have a minimum IP67 rating.

Temperature range from -67°F (-55°C) to 257°F (125°C) continuous at rated current.

Only solid contacts will be used. Stamped and formed contacts are unacceptable.

All contacts shall be soldered unless a crimping tool or machine is used that gives an even and precise pressure for the terminal being used.

All contacts shall be pull-tested to insure their integrity.

WEATHERPROOF DOOR SWITCHES Due the harsh environment and susceptibility to moisture on the fire ground, the fire apparatus compartment doors shall utilize weatherproof switches. Two different types of switches shall be used. Weatherproof proximity switches shall be utilized. No Exceptions.

The switches shall be used for activation of the compartment lights and to provide a signal to the door open circuit in the cab.

V-MUX ELECTRICAL MANAGEMENT SYSTEM The apparatus shall be equipped with a V-MUX Multiplex System. There are several key benefits to multiplexing, one is to reduce the number of connections in a vehicles electrical system, because of this it is important to limit the amount of modules that control certain functions of the vehicle.

Outputs: The outputs shall perform all the following items without added modules to perform any of the tasks: Quote No: 0015791 Page 43 of 49

Smeal Fire Apparatus Co.

SO#:

Load Shedding: The System shall have the capability to Load Shed with 8 levels any output. This means you can specify which outputs (barring NFPA restrictions) you would like Load Shed. Level 1 12.9v, Level 2 12.5V, Level 3 - 12.1V, Level 4 - 11.7V, Level 5 11.3V, Level 6 10.9V, Level 7 10.5, Level 8 10.1. Unlike conventional load shedding devices you can assign a level to any or all outputs. No add-on modules shall be acceptable; the module with the outputs must perform this function.

Load Sequencing: The System shall be able to sequence from 0 8 levels any output.

With 0 being no delay and 1 being a 1 second delay, 2 being a 2 second delay and so on. Sequencing reduces the amount of voltage spikes and drops on your vehicle, and can help limit damage to your charging system. No add-on modules shall be acceptable; the module with the outputs must perform this function.

Output Device: The System shall have solid-state output devices. Each solid-state output shall be a MOS-FET (Metal Oxide Semiconductor - Field Effect Transistors); MOS-FETs are solid-state devices with no moving parts to wear out. A typical relay when loaded to spec has a life of 100,000 cycles. The life of a FET is more than 100 times that of a relay. No add-on modules shall be acceptable; the module with the outputs must perform this function.

Flashing Outputs: The System shall be able to flash any output in either A or B phase, and logic is used to shut down needed outputs in park, or any one of several combined interlocks. The flash rate can be selected at either 80, or 160 FPM. This means any light can be specified with a multiplex truck with no need to add flashers.

Flashing outputs can also be used to warn of problems. No add-on modules shall be acceptable; the module with the outputs must perform this function.

PWM: The modules shall have the ability to PWM at some outputs so that a Headlight PWM module is not needed. No add-on modules shall be acceptable; the module with the outputs must perform this function.

Diagnostics: An output shall be able to detect either a short or open circuit.

Inputs: The inputs shall have the ability to switch by a ground or battery signal.

The inputs shall be filtered for noise suppression via hardware and software so that RF or dirty power will not trick an input into changing its status.

System Network: The Multiplex system shall contain a Peer-to-Peer network. A Master Slave Type network is not suitable for the Fire/Rescue industry. A Peer-to-Peer network means that all the modules are equal on the network; a Master is not needed to tell other nodes when to talk.

System Reliability: The Multiplex system shall be able to perform in extreme temperature conditions, from -40° to +85° C (-40° to +185° F.) The system shall be sealed against the environment, moisture, humidity, salt or fluids such as diesel fuel, motor oil or brake fluid. The enclosures shall be rugged to withstand being mounted in various locations or compartments around the vehicle. The modules shall be protected from over voltage and reverse polarity.

12 VOLT SYSTEMS TEST After completion of the unit, the 12 volt electrical system shall undergo a battery of tests Quote No: 0015791 Page 44 of 49

Smeal Fire Apparatus Co.

as listed in NFPA 1901. These tests shall include, but not be limited to:

• • • •

Reserve capacity test Alternator performance test at idle Alternator performance test at full load Low voltage alarm test Certification of the results shall be supplied with the apparatus at the time of delivery.

SO#: TAIL LIGHTS There shall be a Whelen 600 series LED tail light assembly installed on each side of the rear of the apparatus. Each assembly shall include one (1) red LED stop/tail combination light model number 60BTT, one (1) amber LED model 60A00TAR turn light with arrow and one (1) clear LED backup light model 60C00WCR. The lights shall be mounted in a chrome plated four (4) light composite housing. The remaining slot in the housing shall be filled with a warning light specified in the warning light section.

MIDSHIP TURN SIGNALS There shall be two (2) Truck-Lite model 21 LED midship auxiliary/turn signal lights installed. One (1) light shall be located in the rub rail on each side of the body.

BODY GROUND LIGHTING There shall be Truck-Lite, model 44, 4" round LED lights shall be installed beneath the apparatus in areas where personnel may be expected to climb on and off of the apparatus. The lights shall illuminate the ground within 30" of the apparatus to provide visibility of any obstructions or hazards. These areas shall include, but shall not be limited to, side running boards and the rear step area.

The lights shall be activated when the parking brake is engaged.

CLEARANCE LIGHTS Grote model 65282 red LED clearance lights shall be installed in the rear tailboard as necessary to be in full compliance with applicable ICC and DOT codes and regulations.

Clearance reflectors shall be placed on the apparatus to be in full compliance with applicable ICC and DOT codes and regulations.

BACK-UP ALARM The backup alarm shall be an Ecco 510 Dba type. The sound level shall be 87 decibels.

UPPER ZONE A There shall be one (1) Whelen Engineering Freedom, model FN55VLED, 55" LED lightbar installed on the chassis cab roof. The lightbar shall be equipped with two (2) forward facing linear red LED, two (2) forward facing linear white LED, two (2) corner forward facing red LED, and two (2) corner rear facing red LED lights.

The lightbar shall be equipped with clear lenses. All clear LED lights in the lightbar shall be deactivated in the Blocking Right of Way mode.

Quote No: 0015791 Page 45 of 49

Smeal Fire Apparatus Co.

SO#: UPPER ZONE C There shall be two (2) Whelen RB6 Series rotating beacons installed in Upper Zone C, high at the rear of the apparatus. The 150 FPM single reflector halogen beacons shall incorporate one 12V/50W snap-in halogen lamp, metalized reflector, and a non-optic hard coated polycarbonate lens. The hard coated lens shall provide extended life/luster protection against UV and chemical stresses. The beacons motorized assembly shall include a double roller ball bearing design and motor/worm assembly that produces minimal friction and reduced noise. The beacon dome lenses shall be sealed to a non corroding base with an “O” ring gasket and clamp ring assembly. The solid state halogen beacon lights shall be vibration resistant.

The driver's and officer's side beacons shall both have red LED's and red lenses.

LOWER ZONE WARNING LIGHT PACKAGE There shall be eight (8) Whelen 600 Series Super-LED® lights with chrome-plated flange installed in the lower zone of the apparatus to meet NFPA compliance. The hard coated lens shall provide extended life/luster protection against UV and chemical stresses. The conformal coated PC board and sealed lens/reflector assembly shall provide additional protection against environmental elements. The solid state warning lights shall be vibration resistant.

The lower zone warning lights shall all have red LED's and red lenses.

CHASSIS PAINT The single tone chassis cab shall be painted by the chassis manufacturer.

CHASSIS CAB COLOR The chassis cab shall be painted with PPG High Solids Polyurethane Base Coat. The single tone chassis shall be painted (RED) PPG# FBCH-71096-ALT.

BODY PAINT PREPARATION After the body and components have been fabricated and assembled they then shall be disassembled prior to painting so when the apparatus is completed there shall be finish paint beneath the removable components. The apparatus body and components shall be metal finished as follows to provide a superior substrate for painting.

All aluminum sections of the body shall undergo a thorough cleaning process starting with a phosphoric acid solution to begin the etching process followed by a complete rinse. The next step shall consist of a chemical conversion coating applied to seal the metal substrate and become part of the aluminum surface for greater film adhesion.

After the cleaning process, the body and its components shall be primed with a High Solids primer and the seams be caulked.

All bright metal fittings, if unavailable in stainless steel or polished aluminum, shall be heavily chrome plated. Iron fittings shall be copper under plated prior to chrome plating.

PAINT PROCESS The paint process shall follow the strict standards as set forth by PPG Fleet Finish Quote No: 0015791 Page 46 of 49

Smeal Fire Apparatus Co.

SO#: Guidelines.

The body shall go through a three-stage paint process: primer coat, base coat (color), and clear coat. In the first stage of the paint process the body shall be coated with PPG F3980 Low VOC / High Solids primer to achieve a total thickness of 2-4 mills. In the second stage of the paint process the body shall be painted with PPG FBCH Delfleet™ High Solids Polyurethane Base Coat. A minimum of two to three coats of paint shall be applied to achieve hiding. In the final stage of the paint process the body shall be painted with PPG DCU-2002 Clear Coat. A minimum of two to three coats shall be applied to achieve a total dry film thickness of 2-3 mills.

As part of the curing process the painted body shall go through a Force Dry / Bake Cycle process. The painted components shall be baked at 185 degrees for 3 hours to achieve a complete coating cure on the finished product.

HAND POLISHED After the Force Dry / Bake Cycle and ample cool down time, the coated surface shall be sanded using 3M 1000, 1200, and or 1500 grit sandpaper to remove surface defects. In the final step, the surface shall be buffed with 3M super-duty compound to add extra shine to coated surface. No more than .5 mil of clear shall be removed in this process.

BODY COLOR The body shall be painted with PPG High Solids Polyurethane Base Coat. The single tone body shall be painted (RED) PPG# FBCH-71096-ALT.

UNDERCOATING The apparatus shall undergo a two (2) step undercoating process. The first step shall be a rubberized polyurethane base compound that is applied after the body has been primed. The materials used incorporate unused paint products to reduce the amount of waste released into the environment. This coat shall be applied to all hidden pockets and surfaces that shall not be visible after completion.

As a final step, the entire underside of the body shall be coated with a bituminous based automotive type undercoating when the apparatus is completed. During this application, special care shall be taken to avoid spraying the product on air lines, cables, or other items that would cause normal maintenance to be hindered.

CORROSION PREVENTION One (1) 3.75 ounce tube of Electrolysis Corrosion Kontrol (ECK) shall be provided to use whenever additional items are mounted to the apparatus.

ECK protects aluminum and stainless steel against electrolytic reaction, isolates dissimilar metals and gives bedding protection for hardware and fasteners. ECK contains anti-seizing lubricant for threads. ECK is dielectric and perfect for use with electrical connectors.

TOUCH UP PAINT One (1) two ounce bottle of acrylic enamel touch-up paint or two (2) touch up paint pens, if color is available, shall be supplied.

Quote No: 0015791 Page 47 of 49

Smeal Fire Apparatus Co.

3" GOLD LEAF LETTERING SO#: There shall be up to one hundred (100) 22KT gold leaf letters provided and installed on the apparatus. The letters shall be approximately 3" tall with black outline and shadow.

REFLECTIVE STRIPE FRONT TERMINATION The NFPA reflective stripe located on the side of the apparatus shall wrap around the front of the chassis cab and terminate at chassis grill.

RUB RAIL REFLECTIVE STRIPING There shall be 2" reflective striping installed in the rub rail channel. The reflective striping shall be diamond grade quality material for increased visibility. The reflective shall be silver in color.

NFPA COMPLIANT REFLECTIVE STRIPING Reflective striping shall be applied to the exterior of the apparatus in a manner consistent with NFPA 1901. It shall consist of a straight, 4" wide stripe along the front of the chassis and along the sides, staying below the tops of the wheel well areas.

The color of the main reflective striping on the apparatus shall be white.

CHEVRON COLOR - RED/FLUORESCENT YELLOW-GREEN The chevron striping shall consist of 3M part numbers 1172 EC, red and 3983, fluorescent yellow-green.

Only 3M Diamond Grade™ VIP Reflective Striping shall be used. 3M Diamond Grade™ VIP Reflective Striping is a wide angle prismatic lens reflective sheeting designed for the production of durable traffic control signs and delineators that are exposed vertically in service. This sheeting is designed to provide higher sign brightness than sheetings that use glass bead lenses. It is intended to also provide high sign brightness in the legibility distance where other sheetings do not.

CHEVRON REFLECTIVE STRIPING ON REAR In addition to the custom striping pattern supplied on the apparatus, there shall be additional reflective striping applied to the entire rear of the unit. The reflective striping shall cover at least 50% of the rear facing vertical surface per NFPA 1901. The striping shall consist of a solid base layer of reflective material and alternate between the exposed base layer material and durable, transparent, acrylic colored film. Each stripe shall be a minimum of 6" in width and shall be applied to the apparatus at 45° angle.

The chevron pattern shall include any painted storage compartment doors.

FIVE (5) YEAR PARTS AND LABOR WARRANTY OEM installed purchased parts and fabricated parts shall be free of defects in material and workmanship for a period of five (5) years starting thirty (30) days after the original invoice date. For further details, please refer to the complete warranty document.

Quote No: 0015791 Page 48 of 49

Smeal Fire Apparatus Co.

TEN (10) YEAR WARRANTY BODY STRUCTURAL INTEGRITY SO#: The body shall be free of structural or design failure or workmanship for a period of ten (10) years or 100,000 miles starting thirty (30) days after the original invoice date.

FIVE (5) YEAR 100% V-MUX ELECTRICAL WARRANTY The V-mux electrical system shall be free of defects in design and workmanship for a period of five (5) years starting thirty (30) days after the original invoice date. For further details, please refer to the complete warranty document.

TEN (10) YEAR STAINLESS STEEL PLUMBING LIMITED WARRANTY The stainless steel plumbing and piping shall be free from corrosion perforation for a period of ten (10) years starting thirty (30) days after the original invoice date.

WATER TANK WARRANTY The tank shall be complete with a lifetime warranty. The tank manufacturer shall mark the tank and furnish notice that indicates proof of warranty. For further details, please refer to the complete warranty document.

TWENTY (20) YEAR GALVANIZED SUB-FRAME WARRANTY The galvanized sub-frame shall be free of structural or design failure or workmanship for a period of twenty (20) years starting thirty (30) days after the original invoice date. For further details, please refer to the complete warranty document.

TEN (10) YEAR PAINT LIMITED WARRANTY The apparatus body and pump house shall be free of blistering, peeling and any other adhesion defect caused by defective manufacturing methods or paint material selection for exterior surfaces for a prorated period of ten (10) years starting thirty (30) days after the original invoice date.

Paint on the undercarriage, body interior (Line-X® coating included) or aerial structure related paint, if applicable, is covered only under the Standard One (1) Year Limited Warranty.

TEN (10) YEAR CORROSION LIMITED WARRANTY The body exterior paint shall be warranted against corrosion perforation for a prorated period of ten (10) years starting thirty (30) days after the original invoice date. For further details, please refer to the complete warranty document.

PUMP WARRANTY The fire pump shall be warranted by Waterous for a period of five (5) years from the date of delivery to the fire department or five and one-half (5-1/2) years from the shipment date by Waterous, whichever period shall be first to expire. For further details, please refer to the complete warranty document.

Quote No: 0015791 Page 49 of 49

F R E I G H T L I N E R Vehicle Configuration S P E C I F I C A T I O N P R O P O S A L General Service Engine

M2 106 CONVENTIONAL CHASSIS 2016-17 MODEL YEAR SPECIFIED SET BACK AXLE - TRUCK FIRE/EMERGENCY SERVICE MEDIUM TRUCK 2 YEAR WARRANTY EXPECTED FRONT AXLE LOAD: 12000 lbs EXPECTED REAR DRIVE AXLE LOAD: 24000 lbs EXPECTED GROSS VEHICLE CAPACITY: 36000 lbs CUM ISL 350 HP @ 2000 RPM, 2200 GOV RPM, 1000 LB/FT @ 1400 RPM

Engine Equipment

2015 ONBOARD DIAGNOSTICS/2010 EPA/CARB/GHG14 NFPA COMPLIANT EMBER SCREEN AND FIRE RETARDANT DONALDSON AIR CLEANER DR 12V 275 AMP 40-SI QUADRAMOUNT PAD ALTERNATOR WITH REMOTE BATTERY VOLTAGE SENSE (3) ALLIANCE MODEL 1031, GROUP 31, 12 VOLT MAINTENANCE FREE 2280 CCA THREADED STUD BATTERIES WITH POSITIVE JUMPSTART POST BATTERY BOX FRAME MOUNTED WIRE GROUND RETURN FOR BATTERY CABLES WITH ADDITIONAL FRAME GROUND RETURN POSITIVE LOAD DISCONNECT WITH CAB MOUNTED CONTROL SWITCH MOUNTED OUTBOARD DRIVER SEAT CUMMINS 18.7 CFM AIR COMPRESSOR WITH INTERNAL SAFETY VALVE CUMMINS EXHAUST BRAKE INTEGRAL WITH VARIABLE GEOMETRY TURBO RH HORIZONTAL AFTERTREATMENT SYSTEM HORTON DRIVEMASTER ON/OFF FAN DRIVE AUTOMATIC FAN CONTROL WITHOUT DASH SWITCH, NON ENGINE MOUNTED 1100 SQUARE INCH ALUMINUM RADIATOR WITH SENDURE HEAT EXCHANGER ANTIFREEZE TO -34F, NOAT EXTENDED LIFE COOLANT GATES BLUE STRIPE COOLANT HOSES OR EQUIVALENT 1224 4dr Page 1 of 6

CONSTANT TENSION HOSE CLAMPS FOR COOLANT HOSES ELECTRIC GRID AIR INTAKE WARMER DELCO 12V 38MT HD STARTER WITH INTEGRATED MAGNETIC SWITCH

Transmission

ALLISON 3000 EVS 5 SPD AUTOMATIC TRANSMISSION WITH PTO PROVISION

Transmission Equipment

TRANSMISSION PROGNOSTICS - ENABLED MAGNETIC PLUGS, ENGINE DRAIN, TRANSMISSION DRAIN, AXLE(S) FILL AND DRAIN PUSH BUTTON ELECTRONIC SHIFT CONTROL, DASH MOUNTED WATER TO OIL TRANSMISSION COOLER TRANSMISSION OIL CHECK AND FILL WITH ELECTRONIC OIL LEVEL CHECK SYNTHETIC TRANSMISSION FLUID (TES-295 COMPLIANT)

Front Axle and Equipment Front Suspension

DETROIT AF-12.0-3 12,000# FF1 71.5 KPI/3.74 DROP SINGLE FRONT AXLE MERITOR 16.5X5 Q+ CAST SPIDER CAM FRONT BRAKES, DOUBLE ANCHOR, FABRICATED SHOES FIRE AND EMERGENCY SEVERE SERVICE, NON ASBESTOS FRONT LINING MERITOR AUTOMATIC FRONT SLACK ADJUSTERS TRW THP-60 POWER STEERING 12,000# TAPERLEAF FRONT SUSPENSION MAINTENANCE FREE RUBBER BUSHINGS - FRONT SUSPENSION FRONT SHOCK ABSORBERS

Rear Axle and Equipment

24,000 LB FIRE/EMERGENCY SINGLE REAR AXLE IRON REAR AXLE CARRIER WITH STANDARD AXLE HOUSING 17T MERITOR EXTENDED LUBE MAIN DRIVELINE WITH HALF ROUND YOKES MERITOR 16.5X7 Q+ CAST SPIDER CAM REAR BRAKES, DOUBLE ANCHOR, FABRICATED SHOES FIRE AND EMERGENCY SEVERE SERVICE NON ASBESTOS REAR BRAKE LINING MERITOR AUTOMATIC REAR SLACK ADJUSTERS 1224 4dr Page 2 of 6

Rear Suspension Brake System

24,000# FLAT LEAF SPRING REAR SUSPENSION WITH HELPER, WITH RADIUS ROD, FOR FIRE/EMERGENCY SPRING SUSPENSION - 1.50" AXLE SPACER CUSTOM AXLE CLAMPING GROUP AIR BRAKE PACKAGE WABCO 4S/4M ABS WITHOUT TRACTION CONTROL BW AD-9 BRAKE LINE AIR DRYER WITH HEATER CUSTOM STEEL AIR BRAKE RESERVOIRS BW DV-2 AUTO DRAIN VALVE WITHOUT HEATER - WET TANK

Electrical Connections Wheelbase & Frame

UPGRADED CHASSIS MULTIPLEXING UNIT UPGRADED BULKHEAD MULTIPLEXING UNIT

Chassis Equipment

(265 INCH) WHEELBASE 11/32X3-1/2X10-15/16 INCH STEEL FRAME 120KSI (63 INCH) REAR FRAME OVERHANG THREE-PIECE 14 INCH CHROME STEEL BUMPER WITH COLLAPSIBLE ENDS AND LH WING CUTOUT FOR SPEAKER FRONT TOW HOOKS - FRAME MOUNTED GRADE 8 THREADED HEX HEADED FRAME FASTENERS

Fuel Tanks Tires

50 GALLON RECTANGULAR ALUMINUM FUEL TANK 6 GALLON DIESEL EXHAUST FLUID TANK ALLIANCE FUEL FILTER/WATER SEPARATOR FUEL COOLER MICHELIN XZE2 11R22.5 14 PLY RADIAL FRONT TIRES MICHELIN XDE M/S 11R22.5 16 PLY RADIAL REAR TIRES

Hubs

CONMET PRESET PLUS IRON FRONT HUBS CONMET PRESET PLUS IRON REAR HUBS 1224 4dr Page 3 of 6

Wheels

22.5X8.25 10-HUB PILOT 6.16 INSET 2-HAND STEEL DISC FRONT WHEELS PAINTED JOB COLOR 22.5X8.25 10-HUB PILOT 2-HAND STEEL DISC REAR WHEELS PAINTED JOB COLOR

Cab Exterior

154 INCH BBC HIGH-ROOF ALUMINUM CONVENTIONAL CREW CAB AIR CAB MOUNTS NFPA COMPLIANT EXTERIOR GRAB HANDLES HOOD MOUNTED CHROMED PLASTIC GRILLE CHROMED HOOD MOUNTED AIR INTAKE GRILLE TUNNEL/FIREWALL LINER SINGLE ELECTRIC HORN DOOR LOCKS AND IGNITION SWITCH KEYED THE SAME INTEGRAL HEADLIGHT/MARKER ASSEMBLY WITH CHROME BEZEL LED AERODYNAMIC MARKER LIGHTS DAYTIME RUNNING LIGHTS DUAL 102” WEST COAST BRIGHT FINISH HEATED MIRRORS WITH LH AND RH REMOTE LH AND RH 8" BRIGHT FINISH CONVEX MIRRORS MOUNTED UNDER PRIMARY MIRRORS 63X14 INCH TINTED REAR WINDOW TINTED DOOR GLASS LH AND RH WITH TINTED NON OPERATING WING WINDOWS TINTED WINDSHIELD 2 GALLON WINDSHIELD WASHER RESERVOIR WITHOUT FLUID LEVEL INDICATOR, FRAME MOUNTED

Cab Interior

OPAL GRAY VINYL INTERIOR MOLDED PLASTIC DOOR PANELS WITH ALUMINUM KICKPLATE LOWER DOORS FORWARD ROOF MOUNTED CONSOLE WITH UPPER STORAGE COMPARTMENTS WITHOUT NETTING IN DASH STORAGE BIN (2) CUP HOLDERS LH AND RH DASH HEATER, DEFROSTER AND AIR CONDITIONER MAIN HVAC CONTROLS WITH RECIRCULATION SWITCH PREMIUM CAB INSULATION SOLID-STATE CIRCUIT PROTECTION AND FUSES 12V NEGATIVE GROUND ELECTRICAL SYSTEM 1224 4dr Page 4 of 6

DOME LIGHT WITH 3-WAY SWITCH ACTIVATED BY LH AND RH DOORS CAB DOOR LATCHES WITH MANUAL DOOR LOCKS (1) 12 VOLT POWER SUPPLY IN DASH HIGH BACK AIR SUSPENSION DRIVER SEAT NFPA COMPLIANT SEATS INC 911 UNIVERSAL SERIES SCBA NON SUSPENSION PASSENGER SEAT WITH UNDERSEAT STORAGE NFPA COMPLIANT SEATS INC 911 UNIVERSAL SERIES SCBA NON SUSPENSION LH, RH AND CENTER REAR PASSENGER SEATS WITH UNDERSEAT STORAGE NFPA COMPLIANT LH AND RH INTEGRAL DOOR PANEL ARMRESTS GRAY VINYL SEAT COVERS WITH GRAY CORDURA CLOTH BOLSTERS AND HEADRESTS NFPA COMPLIANT HIGH VISIBILITY SEAT BELTS ADJUSTABLE TILT AND TELESCOPING STEERING COLUMN 4-SPOKE 18 INCH STEERING WHEEL DRIVER AND PASSENGER INTERIOR SUN VISORS

Instruments & Controls

BLACK GAUGE BEZELS LOW AIR PRESSURE LIGHT AND BUZZER 2 INCH PRIMARY AND SECONDARY AIR PRESSURE GAUGES ENGINE COMPARTMENT MOUNTED AIR RESTRICTION INDICATOR WITH GRADUATIONS, WITH WARNING LIGHT IN DASH ELECTRONIC CRUISE CONTROL WITH SWITCHES IN LH SWITCH PANEL IGNITION SWITCH WITH NON REMOVABLE KEY ICU3S, 132X48 DISPLAY WITH DIAGNOSTICS, 28 LED WARNING LAMPS AND DATA LINKED FIRE AND EMERGENCY SERVICE VEHICLES ENGINE WARNING 2 INCH ELECTRIC FUEL GAUGE ELECTRICAL ENGINE COOLANT TEMPERATURE GAUGE 2 INCH TRANSMISSION OIL TEMPERATURE GAUGE ENGINE AND TRIP HOUR METERS INTEGRAL WITHIN DRIVER DISPLAY ELECTRIC ENGINE OIL PRESSURE GAUGE ELECTRONIC MPH SPEEDOMETER WITH SECONDARY KPH SCALE ELECTRONIC 3000 RPM TACHOMETER 1224 4dr Page 5 of 6

DIGITAL VOLTAGE DISPLAY INTEGRAL WITH DRIVER DISPLAY SINGLE ELECTRIC WINDSHIELD WIPER MOTOR WITH DELAY MARKER LIGHT SWITCH INTEGRAL WITH HEADLIGHT SWITCH ONE VALVE PARK BRAKE SYSTEM WITH DASH VALVE SELF CANCELING TURN SIGNAL SWITCH WITH DIMMER, WASHER/WIPER AND HAZARD IN HANDLE INTEGRAL ELECTRONIC TURN SIGNAL FLASHER WITH HAZARD LAMPS OVERRIDING STOP LAMPS

Design Color

PAINT: ONE SOLID COLOR CAB COLOR A: RED ELITE BLACK, HIGH SOLIDS POLYURETHANE CHASSIS PAINT

T O T A L V E H I C L E S U M M A R Y Weight Summary

Factory Weight + (+) Weights shown are estimates only.

Weight

Front 7886 LBS

Weight

Rear 4397 LBS

Total

Weight 12283 LBS 1224 4dr Page 6 of 6

PROPOSAL

PROPOSAL

PROPOSAL

PROPOSAL

Fri Nov 06 2015 Quote #: 0015795 Page 1 of 9 Customer: Metropolitan Area Planning Council 60 Temple Place, 6th Floor Boston, MA 02111 Quote Summary with Notes Dealership: New England Fire Equipment and Apparatus 10 Stillman Road North Haven, CT 06473 Quote No: 0015795 S.O.#: 911099 911085 911059 911069 911060 980017 911064 980003 911070 980016 911079 980015 980012 911066 911074 900466 900151 900541 900658 900678 Chassis 910012 910019 005241 001200 910021 001379 910156 111597 911113 911284 Quote Name: Unit Type: FCAM Mid Range Pumper 2016 General Info Section Custom Pumper Destination, United States Bidding Prerequisites, United States Intent of Specifications, Pumper Standards Version, NFPA 1901-2009 Description Performance Bond and Payment Bond, Required, 100% Inspection Certificate, NFPA 1901 Compliance Unit Certification, NFPA 1901-2009, Pumper Firefighting Apparatus Documentation, NFPA Owner's Manuals, Electronic, (1) USB Drive Misc. Equipment Allowance, 1,000 Lb.

Tilt Table Test, Required, 26.5 Degrees Pump Certification, Independent Third Party Pump Certification Measure, U.S. GPM Final Inspection, OEM Factory, Required Overall Height, 118 (9'-10") Overall Length, 396" (33'-0") Wheelbase, 193 (16'-1") Angle of Approach, 13 Degrees Angle of Departure, 12 Degrees Chassis Section Custom Chassis, Smeal, Sirius II Axles, Single OEM Chassis Preparations, Sirius Mud Flaps, Custom Chassis Cab Electrical, Multiplex Heat Exchanger, Chassis Supplied and Installed Front Bumper, Chassis Supplied and Installed Map Console, 3-Slot (3" Binders), Abraded Map Console Location, Engine Tunnel Mounted, Drop-In Battery Charger, Chassis Supplied and Installed

008187 000252 910172 910169 010088 Hose Bed 110131 910381 910422 910386 110151 009342 100141 Body / Pump Module 002630 120793 120874 120475 120954 120007 000934 120469 October 27, 2015 Option ID 110034 120404 112088 112095 008398 004901 910048 Water/Foam Tanks 110108 910157 000350 910160 010075

UPO0000972

Quote #: 0015795 Description Page 2 of 9 Helmet Brackets, (4), Zico Flashlights, (4), Streamlight, Fire Vulcan LED, Orange, 44451, Vehicle Mount System EMS Compartment, Forward Facing, Center Rear Cab Wall, Style 3, 48" H x 32" W x 18" D, ROM Door/Lighting, 2 Shelves EMS FInish, Gray Line-X, 1 EMS Compartment Mounting Plate, On Engine Tunnel, Aluminum, Abraded Outlet Bar, 120V, (6) Receptacles, 5-15R Household, Wired to Shoreline Outlet Location, EMS Compartment, Inside Water/Foam Tanks Section Water Tank, UPF, 1000 U.S. Gallons Water Tank Mounting, Pumpers Water Tank Drain, 1-1/2" Valve, Pumpers Water Tank Fill Tower, UPF, Black Water Tank Level Gauge, Innovative Controls SL Plus, Pump Operator's Panel

Water Tank Level Display, Chassis Supplied, Whelen PSTANK, Cab Sides, Innovative Controls Driver

Water Tank Overflow, UPF, 4", Pumpers w/o EHL Foam Tank, UPF, U.S. Gallon, 30 Foam Tank Type, Class A Foam Tank Fill Tower, UPF, Black Foam Tank Level Gauge, Innovative Controls SL Plus, Class A Foam Hose Bed Section Hose Bed, Aluminum, Standard, Painted Primary Body Color Finish Hose Load, Double-Jacket Hose, 200' of 2-1/2" Hose Load, Double-Jacket Hose, 1000' of 5" Hose Load, Double-Jacket Hose, 300' of 2-1/2" Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Bungee, Rear Bungee, Black Hose Bed Dividers, (2), 1/4" Alum., Adjustable, Abraded Hose Bed Loading Lights, (2) Rear, LED, Grote, Trilliant 63901 Body / Pump Module 000474 900960 900966 120709 L1 Body, 100" Wide, Custom Pumper, Single-Axle, Aluminum, 1/8" Side Compartment Doors, Roll-Up Doors, ROM, Satin Finish Compartment Door Handles, All Non-Locking Drip Trays, Rollup Door, ROM, All Compartments Rear Compartment Door, (1), ROM Roll-Up Door, Satin, Non-Locking Compartment Lighting, ROM, V4 LED (11) Compartment Finish, Line-X, Gray Flooring, Turtle Tiles, All Interior Body Compartment Floors / Floor Mounted Trays and Shelves / Adjustable Trays Air Release and Drain Holes, All Compartments Handrail Material, Knurled Aluminum Fuel Fill, Included with Air Bottle Compartment, Driver's Side Driver's (Left) Body Style, Single Axle, L1 Full, L2 Upper, L3 Full L1 Components

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 2 of 9

000574 120785 Cmpt. Layout L2 Height Width Upper Depth Lower Depth Divide Height 000699 Cmpt. Layout L3 Height Width Upper Depth Lower Depth Divide Height 120373 Cmpt. Layout 009397 009421 120727 R1 Height Width Upper Depth Lower Depth Divide Height 002740 120785 Cmpt. Layout R2 Height Width Upper Depth Lower Depth Divide Height October 27, 2015 Option ID Height Width Upper Depth Lower Depth Divide Height 002742 002499 Quote #: 0015795 Description Page 3 of 9 Height - 61" Width - 35" Upper Depth - 26" Lower Depth - 26" Intermediate Divide Height - 0" Shelf, (1), Adjustable, Aluminum, Full Depth (4 Struts), Abraded Tray, (1), Floor-Mounted Roll Out, Austin Hardware, 300#, 100% Extension, Abraded, With Front Drawer Release Mounting Plate, Back Wall of Compartment, Abraded Aluminum Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

L2 Components Height - 28.5" Width - 65" Upper Depth - 26" Lower Depth - 0" Intermediate Divide Height - 0" Tool Board, (1), Split Swing Out Aluminum, Standard Height, Abraded Pegboard The compartment layout shall be detailed at the pre-construction meeting.

L3 Components Height - 61" Width - 42" Upper Depth - 26" Lower Depth - 26" Intermediate Divide Height - 0" Tool Boards, (3), Slide Out Aluminum, Full Height, Full Depth, Abraded Pegboard The compartment layout shall be detailed at the pre-construction meeting.

WL1, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" WL3, Air Bottle Compartment with Fuel Fill, OEM Painted SS Door, Double 8" Officer's (Right) Body Style, Single Axle, R1 Full, R2 Upper, R3 Full R1 Components Height - 61" Width - 35" Upper Depth - 15" Lower Depth - 26" Intermediate Divide Height - 27" Shelf, (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Abraded Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

R2 Components Height - 28.5" Width - 65" Upper Depth - 15" Lower Depth - 0" Intermediate Divide Height - 0"

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 3 of 9

October 27, 2015 Option ID Quote #: 0015795 Description Page 4 of 9 900963 003558 006146 005118 010080 002186 003559 120489 004929 002427 005155 001210 007897 003598 007902 000521 000505 007859 004855 Cmpt. Layout R3 Height Width Upper Depth Lower Depth Divide Height 002740 002499 120785 Cmpt. Layout 009436 009459 121483 T1 Height Width Depth 002742 120357 120785 Cmpt. Layout 005119 120677 Mounting Board, Back Wall of Compartment, PAC Trac The compartment layout shall be detailed at the pre-construction meeting.

R3 Components Height - 61" Width - 42" Upper Depth - 15" Lower Depth - 26" Intermediate Divide Height - 27" Shelf, (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Abraded Tray, (1), Floor-Mounted Roll Out, Austin Hardware, 300#, 100% Extension, Abraded, With Front Drawer Release Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

WR1, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" WR3, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" Rear Body Style, Flat Back, Standard Hose Bed, One Compartment T1 Components Height - 42" Width - 41" Depth - 28" Shelf, (1), Adjustable, Aluminum, Full Depth (4 Struts), Abraded Tray, (1), Floor-Mounted Roll Out, Hansen, 600#, 100% Extension, Abraded Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

Sub-Frame, GS-36, Hot-Dip Galvanized, Custom Pumpers, Aluminum and Galvaneal Bodies Walkways/Overlays/Stepping Surfaces, Tread Plate, NFPA 1901 Rear Deck, Bolt-On, Flat Back, Tread Plate, 13.25" Auxiliary Step, Below Rear Deck, Grip-Strut Rub Rails, "C" Channel Design Tow Option, Rear, Tow Eye, One (1), Underbody Subframe Wheel Wells, Rear, Single Axle Fenderettes, (2), Single Axle, Stainless Steel Exhaust Heat Deflector Shield, 4" Access Panel for Fuel Tank Gauge, Pumpers License Plate Bracket Stainless Steel Screws Bag of Bolts Front Steps and Lighting, Cast Products, Folding Steps (4), Driver's Side Handrail, Body (Front), Top, Driver's Side, Knurled Aluminum Front Steps and Lighting, Cast Products, Folding Steps (4), Officer's Side Handrail, Body (Front), Top, Officer's Side, Knurled Aluminum Overlay, Tread Plate, Vertical Areas of Both Front Compartments Rear Steps and Lighting, Cast Products, Bolt-On Steps, Four (4), 3 Driver's and 1 Officer's Side Handrails, Body (Rear), Rear Face, Vertical, Both Sides, Knurled Aluminum

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 4 of 9

001224 900951 004949 110174 004731 009855 000458 009864 111014 111026 009973 007160 000460 October 27, 2015 Option ID 120690 002221 001296 001293 001291 009219 002272 120631 009281 001224 009282 110222 Quote #: 0015795 Description Page 5 of 9 Handrail, Body (Rear), Below Hose Bed, Horizontal, Knurled Aluminum Ladder Storage, Inside Body, Side of Water Tank, Officer's Side, Tread Plate Door Ladder, (1), Duo-Safety, 24' Two-Section Extension, 900-A Ladder, (1), Duo-Safety, 14' Roof, 775-A Ladder, (1), Duo-Safety, 10' Folding Attic, 585-A Pike Pole Tubes, (2), In Ladder Storage Compartment Pike Pole, (1), Akron, 6' Fiberglass, Standard Hook, Ultra-Lite, UL-6 Pike Pole, (1), Akron, 8' Fiberglass, Standard Hook, UT-8 Hard Suction Hose Storage, One (1) Hose, Enclosed in Ladder Compartment Hard Suction Hose, (1), Firequip, 6" x 10' (OAL 10' 6"), Maxi-Flex PVC Hard Suction Hose Storage, One (1) Hose, Behind Driver's Side Header, Enclosed Compartment, Painted Door Hard Suction Hose, (1), Firequip, 6" x 10' (OAL 10' 6"), Maxi-Flex PVC Wheel Chock Storage, Under Front of Body, Driver's Side Wheel Chocks, (1) Pair, Cast Products, TMC1008-4 and Bracket, OEM Installed Pump Module, Side Mount, Independent, 1/8" Aluminum Pump Compartment Internal Lighting, LED, On-Scene Pump Compartment Heater, (1) 40,000 BTU, Switch on Pump Panel Heat Shield, Removable, Heavy Duty Running Board, Driver's Side, Bolt-On, Tread Plate Running Board, Officer's Side, Bolt-On, Tread Plate, Storage Well, Floating, PAC Straps Running Board Storage Well Tile, (1), Dri-Dek Flooring Dunnage Compartment, Tread Plate, Above Pump Module, NO Cover Access Panel, Pump, Front Pump Module, Bolt-On, Painted Aluminum, Bolt-On Access Panel, Pump, Officer's Side Pump Module, Side-Hinged, Tread Plate, Compression Latches Pump Panels, Side Mount, Controls on Driver's Side, Black Line-X Finish, IC Bezels/Trim Rings/Labels Pump Panel Lighting, Side Panels, LED, On-Scene Night Axe Pump Panel Lighting Activation, Automatic with Park Brake Engaged Pump / Foam System 003659 910612 Pump / Foam System 100153 000090 002792 910622 910640 100266 009531 002210 006588 000112 000087 910645 111069 100722 Pump, Waterous, Single-Stage, 1500 GPM, CSUC20, Flame Plated Impeller Hubs Mechanical Seals, Waterous Anodes, Waterous, Zinc, 2 Discharge, 2 Intake Pump Rating, 1500 GPM Pump Mounting, Independent Pump Module Pump Shift and Lights, Waterous, Air-Operated Governor, Pump Boss 400, FRC Intake Relief Valve, Pump, Elkhart, Factory Preset Primer, Trident, AirPrime (3-Barrel), Air-Operated Valve Master Drain Valve, Trident Overheat Protection Manager (OPM), Waterous, With Lights Pump Color Primed Black - Intakes Unpainted Pump and Engine Cooling System, Inn. Cntrls, 3/8" I.D., Hose, Controls on Pump Panel Foam System, FoamPro, 2001, Single System, Class A Foam, Flush System

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 5 of 9

October 27, 2015 Option ID Quote #: 0015795 Description Page 6 of 9 980014 006644 910503 911030 111058 911038 910527 100377 100349 100310 Tank/Pump Plumbing Labels Intakes 100381 001252 002588 007059 001246 100385 005619 111073 111076 100476 Intake Labels Discharges 002545 111712 111050 100527 002545 111712 111050 100527 002538 100659 111050 Foam System Testing, Single System Manifold, Waterous, Standard, Side Mounts, Foam Akron 8800 - Push/Pull Discharges (RC-10 on 3" or Larger) - Manual Inlets Gauge Brand, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauges - psi 0-400 Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-400 Include with Master Pressure Gauge Assembly Hardware Brand, South Park, NST Inlet Swivels, NST Discharges, TFT Storz Drains, Innovative Controls, Manual Lift Handle Pump to Tank Fill, 2", Akron 8800 2" Manual Valve, IC Push-Pull Handle Tank to Pump, 3", Akron 8800 3" Manual Valve, IC Push-Pull Handle Tank/Pump Plumbing Labels - The tank plumbing valves and controllers shall have the OEM Standard label package unless stated otherwise. The Pump-to-Tank Fill shall be labeled "TANK FILL" and shall have a Black label color. The Tank-To-Pump shall be labeled "TANK TO PUMP" and shall have a Navy Blue label color.

Intakes Steamer, Driver Side, 6", Short Tube, Full-Body Pump, MNST Cap, 6" NST, Vented Chrome, South Park Inlet, Driver-Side, 2-1/2", Fully Recessed Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, TSC Handle Plug, NST, 2-1/2", South Park Steamer, Officer Side, 6", Short Tube, Full-Body Pump, MNST Butterfly Valve, Side Steamer, 6" Manual, Neles Jamesbury Bleeder Valve, Inn. Cntrls Intake Relief Valve, Steamer, Elkhart, Factory Preset Elbow (30 Deg.) 6" FNST x 4" Storz 30 Degree Elbow, 4" Cap and Chain, Rocker Lug, TFT Intake Labels - All intakes shall have the OEM Standard label package unless stated otherwise. All intake labels shall be burgundy in color. Specific verbiage on each intake label tag shall be determined at the pre-construction meeting.

Discharges Discharge, Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8625, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8625, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Officer-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 6 of 9

100527 007440 007013 007018 000205 009843 007020 110289 910701 910654 910534 100653 111050 October 27, 2015 Option ID 100527 002553 100663 111050 100613 002550 910534 100658 111050

UPO0000973

002543 100658 111050 100527 002541 100658 111050 910526 910701 910654 910534 100653 111050 910526 910702 910660 Quote #: 0015795 Description Page 7 of 9 Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Officer-Side, 4", NST (625 GPM) Valve, 3", Akron, Manual, Slow Close, 8830, Stainless Ball, Elkhart RC-10 Handwheel Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 4" FNST x 4" Storz - Adapter, 4" Storz x 2-1/2" NST, TFT - Cap, Chrome, South Park Discharge, Front Bumper Driver-Side, 2-1/2", Above Gravelshield, NST (250 GPM) Foam Capable Discharge Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400

Reducer, South Park, 2-1/2 inch FNST x 1-1/2 inch MNST, A3720-AC

Discharge, Rear Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Rear Officer-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Crosslays, Above Pump Panel, (2) 1-1/2" and (1) 2-1/2" Pre-Connect Hose Bed Housing Coating, Abraded Finish Flooring, Dura-Dek Crosslay Rollers Crosslay Dividers, (2), Black Line-X Aluminum Crosslay Cover, Hinged Tread Plate, Side Mount Crosslay End Covers, Vinyl, C-Rail Top and Bungee Bottom, Black Preconnect, Crosslay/Speedlay, 1-1/2", NST Crosslay Load, 200' of 1-3/4" Hose, Single Stack Foam Capable Discharge Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Preconnect Discharge Preconnect, Crosslay/Speedlay, 1-1/2", NST Crosslay Load, 200' of 1-3/4" Hose, Single Stack Foam Capable Discharge Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Preconnect Discharge Preconnect, Swivel, Crosslay/Speedlay, 2-1/2", NST Crosslay Load, 200' of 2-1/2" Hose, Single Stack

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 7 of 9

October 27, 2015 Option ID Quote #: 0015795 Description Page 8 of 9 910534 100658 111050 910526 100512 100663 111050 006617 112018 Valve, 3", Akron, Manual, Slow Close, 8830, Stainless Ball, Elkhart RC-10 Handwheel Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Deck Gun, Manual, Elkhart Stinger 2.0 8297-10, 3" NPT Inlet Monitor Color, Elkhart Red, RAL3003 002583 Stacked Tips (Quad) and Stream Shaper, Elkhart, ST-194, 283A Discharge Labels Discharge Labels - All discharges shall have the OEM Standard label package unless stated otherwise. Each discharge label shall be a unique color. Specific verbiage and colors on each discharge label tag shall be determined at the pre-construction meeting.

Low Voltage 002955 911058 002849 005907 008730 110366 006261 000847 Foam Capable Discharge Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Preconnect Discharge Deluge, Center, 3", NPT (375 GPM) Low Voltage Electrical System, Pumper, Weldon V-MUX Multiplex, QL-12 Harnesses, Sealed Switches Electrical System Test, 12 Volt Tail Lights, LED, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup/Warning, 4 Light Vertical Casting Additional Activation, Back-Up Lights Wired to Rear Work Light Switch / In-Cab Switch Turn Signals, (2) in Rub Rail, LED, Truck-Lite, Model 21 Ground Lights, LED, Truck-Lite Model 44, Activation by Park Brake Clearance Lights, LED, Grote, Red (Pumper, Squrt, and TeleSqurt) Upper Zone A, Lightbar, Whelen, 60", Freedom LED, Raised Roof, 8 Red, 2 White (Fully Populated Front) 110409 Upper C Light / Lens Color 110473 Lower Zone Light/Lens Color 004948 910738 000890 110629 910851 000870 Line Voltage 003798 007421 000680 002784 000683 910725 110859 Upper Zone C, Rotating Beacons (2), Whelen, L31 LED Light/Lens Color - The driver's and officer's side beacons shall both have red LED's and red lenses.

Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, 600 Series Light/Lens Color - The lower zone warning lights shall all have red LED's and red lenses.

Traffic Advisor, Whelen, 6-Light, TIR6 LED Low-Profile, TAM65, TACTLD1 Controller Traffic Directional Light Location, Rear Body Face, Recess Mounted Air Horn Activation, Push Button on Pump Panel, Driver's Side Scene Lights, Pair, 12V, Whelen, Surface Mount, LED 600 Series Gradient Opti-Scene Lighting Location, Rear Face of Body, Both Sides Lighting Activation, In Cab and On Pump Panel, 'REAR SCENE', Wired to Reverse, Rocker Switches Line Voltage Generator, Hydraulic, Onan, 6kW, 6RBAB, Onan Display Generator Start, Hydraulic Gen., On Pump Panel Generator PTO, Standard Hot Shift, Pumper Generator Location, Above Pump Module, Onan Generator Load Center, 8-Circuit, Non-GFI Breaker Box Generator Load Center Location, L1, Forward Bulkhead Cord Reel, Akron, 120V, 150' 10/3 Yellow Cord, Hardwired Junction Box, Extenda-Lite

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 8 of 9

October 27, 2015 Option ID 000876 910860 910860 910860 910860 910866 110918 110760 Quote #: 0015795 Description Page 9 of 9 Junction Box Option, Powder Coat Yellow Junction Box Receptacle, 120V, 5-15R Household, Duplex Junction Box Receptacle, 120V, 5-15R Household, Duplex Junction Box Receptacle, 120V, 5-15R Household, Duplex Junction Box Receptacle, 120V, 5-15R Household, Duplex Cord Reel Location, Dunnage Area Junction Box Mounting Bracket, Tread Plate Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Push-Up, LED Spectra 20,000 Lumen Lighting Location, On Rear Face of Custom Chassis, Both Sides Lighting Activation, Pair, Circuit Breakers Only Paint / Striping / Decals 110832 110846 Paint / Striping / Decals 900718 009171 008841 001170 006089 001033 120031 911237 120139 900879 004522 008610 900906 900935 006009 Warranties W05451 990028 W05901 990032 WLF800 990030 W10201 W05810 W05810 Chassis Paint, Chassis Manufacturer Painted, Two Tone Body Paint, Single Tone, Pumper, Aluminum Material Body Paint Color, Pumper/Squrt/TS, Single Tone, Red, PPG# FBCH-71096-ALT Under Body Finish, Two-Step Undercoating Process Corrosion Protection, Electrolysis Corrosion Kontrol (ECK) Touchup Paint, 2 Oz. Bottle 100 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" Reflective Lettering, White Lettering, Reflective, 18", Quantity up to 4 Front Cab Striping, Wrap to Grill Rub Rail Striping, 2", Silver, Reflective, Pumper/Squrt/TS Body Striping, Pumper/Squrt/TS, 4", Straight Around Perimeter Main Stripe Color, White Chevron Color, Red / Fluorescent Yellow-Green Chevron Layout, Rear Body Surface, Painted Storage Doors Warranties Warranty, Parts and Labor, 5 Year (Pumper) Warranty, Body Structural Integrity, 10 Year Warranty, 100% V-Mux Electrical, Smeal Parts and Labor, 5 Year (Pumper) Warranty, Plumbing, Stainless, 10 Year Warranty, Water Tank, UPF, Standard Lifetime Warranty, Substructure, Galvanized, 20 Year, Pumper, Rescue Warranty, Paint, 10 Year, Corrosion, 10 Year (Pumper) Warranty, Pump, Waterous, Standard 5 Year Warranty, Pump, Waterous, Standard 5 Year

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 9 of 9

Smeal Fire Apparatus Co.

PREREQUISITE BIDDING REQUIREMENTS Any manufacturer submitting a proposal or bid, to these specifications, shall meet the following conditions:

• • • •

The manufacturer of the apparatus herein specified, shall be wholly owned (100%) and managed by a Company, Corporation, and/or Parent Company that is wholly based and permanently resides in the United States of America.

The Company, Corporation, and/or Parent Company, and all assets belonging to such, shall be wholly owned and managed (100%) by the entities specified above Any proposal, bid, or response to these specifications by any foreign based, owned, or managed (in part or in whole) Company, Corporation, and/or Parent Company shall be cause for immediate rejection.

Any proposal, bid, or response to these specifications by any Company, Corporation, and/or Parent Company, that is owned, operated, managed, or held in contract, in part or wholly by a partnership or other agreement, shall be cause for immediate rejection.

Exceptions to these conditions will not be allowed under any circumstances.

INTENT OF SPECIFICATIONS It is the intent of these specifications to cover the furnishing and delivery to the purchaser of a complete apparatus equipped as herein specified. With a view to obtaining the best results and the most acceptable apparatus for service in the fire department, these specifications cover the general requirements as to the type of construction, together with certain details as to finish, equipment, and appliances with which the successful bidder must conform. Minor details of construction and materials where not otherwise specified are left to the discretion of the contractor, who shall be solely responsible for the design and construction of all features.

Bids shall only be considered from companies that have an established reputation in the field of fire apparatus construction and have been in business for a minimum of 50 years.

Each bidder shall furnish satisfactory evidence of his ability to construct the apparatus specified, and shall state the location of the factory where the apparatus is to be built.

The bidder shall also show that they are in a position to render prompt service and furnish replacement parts for said apparatus.

CONTRACTOR'S SPECIFICATIONS Each bid shall be accompanied by a set of "Contractor's Specifications" consisting of a detailed description of the apparatus and equipment proposed and to which the apparatus furnished under contract must conform.

These specifications shall indicate size, type, model, and make of all component parts and equipment.

TIMELY PROPOSALS It is the bidder's responsibility to see that their proposals arrive on time. Late proposals, facsimiles, e-mails, telegram, or telephone bids shall not be considered.

DRAWINGS All bid drawings shall be stamped PROPOSAL.

Quote No: 0015795 Page 1 of 62 October 27, 2015

Smeal Fire Apparatus Co.

• • • • • • • •

A total of six (6) packets of 11" x 17" drawings, each packet complete with a single view drawing for each side of the apparatus shall be supplied

• • •

All drawings shall be drawn and printed to an appropriate scale to maximize the size of the apparatus on each 11" x 17" sheet of paper.

Compartment door opening dimensions shall be shown in each compartment.

Drawings shall be five (5) views. (left, right, front, rear, top) with the exception of chassis that are not always available as AutoCAD drawings

Rear plumbing, such as 2-1/2" discharges, rear steamers, and direct tank fills, shall be shown

Ladders shall be labeled with a letter designation referring to the table for an explanation of the ladder type

OAL (overall length) in feet and inches - Estimated length shall be rounded up to the nearest inch

OAH (overall height) in feet and inches - Estimated height shall be rounded up to the nearest inch

• • • • • •

Body dimensions shown - pump house width and front of the body to centerline of the rear axle Wheelbase in inches Estimated in-service weight Turning clearance radius Front and rear overhang in inches No pump panel or instrument panel controls, discharges or inlets. To be blank and labeled "Pump Panel"

• • • • • • • •

Water tank outline Foam tank(s) fill towers Exterior mounted hard suction hose Warning lights D.O.T. lights Generator outline No front bumper layout Rollup doors will be shown in open position. Lap doors will be shown in the closed position

Compartment depth break over measurement. The measurement where the compartment switches from full depth to shallow depth

• •

Angle of approach and departure Top view of chassis Text Block Items Chassis model Water tank capacity Foam tank capacity Hose bed capacity in cubic feet Total compartment cubic feet Drawing box is to read "BID" and utilize the bid number Drawings shall be printed on white paper with black ink; blue line drawings shall not be acceptable.

PURCHASER'S OBLIGATIONS The purchaser reserves the right to accept or reject any or all bids on such basis as the purchaser deems to be in its best interest. All bidders shall be advised that the purchaser is not bound in any manner to automatically accept the lowest bid. The purchaser shall Quote No: 0015795 Page 2 of 62 October 27, 2015

Smeal Fire Apparatus Co.

only be obligated to purchase the lowest bid that meets these detailed specifications as closely as possible.

SAFETY REQUIREMENTS It is required that the bidder shall meet all State and Federal safety standards and laws that are in effect on the date of the bid for the item(s) that are being specified and the particular use for which they are meant.

ACQUAINTANCE WITH SPECIFICATIONS It is the responsibility of the bidder to review all of the bidding requirements. Failure of a bidder to be acquainted with this information shall not relieve them from any obligations of the bid requirements.

QUALITY AND WORKMANSHIP The design of the apparatus shall embody the latest approved automotive engineering practices. Experimental designs and methods shall not be acceptable.

The workmanship shall be of the highest quality in its respective field. Special consideration shall be given to the following points: accessibility of the various units that require periodic maintenance, ease of operation (including both pumping and driving), and symmetrical proportions.

GENERAL CONSTRUCTION The complete apparatus, assemblies, subassemblies, component parts, and so on, shall be designed and constructed with due consideration to the nature and distribution of the load to be sustained and to the general character of the service to which the apparatus is to be subjected when placed in service.

All parts of the apparatus shall be strong enough to withstand the general service under full load. The apparatus shall be so designed that the various parts are readily accessible for lubrication, inspection, adjustment and repair.

The apparatus shall be designed and constructed, and the equipment so mounted, with due consideration to distribution of the load between the front and rear axles, and side to side loading that all specified equipment, including a full complement of specified ground ladders, full water tank, loose equipment, and firefighters; shall be carried without overloading or damaging the apparatus as per requirements defined in NFPA 1901.

The main apparatus body structure shall have an approximate width of 100" in order to maximize the enclosed compartment space of the apparatus. The 100" wide measurement represents the main body structure measured from the bottom, outermost rear corners of the apparatus body structure. Components affixed or fastened to the apparatus will increase the body width proportionately.

LIABILITY The bidder, if their bid is accepted, shall defend any and all suits and assume all liability for the use of any patented process, device or article forming a part of the apparatus or any appliance furnished under the contract.

Quote No: 0015795 Page 3 of 62 October 27, 2015

Smeal Fire Apparatus Co.

WARRANTY A copy of the warranties for the chassis, pump, body, paint, and water tank shall be furnished with each bidder's proposal.

BID FORMS / SPECIFICATIONS All bid forms shall be submitted on the attached bid form. The bid form and/or these specifications shall be filled out by checking either the "YES" or "NO" column for each and every section/paragraph. Failure to use this form and/or these specifications shall be cause for immediate rejection of any bid.

EXCEPTION TO SPECIFICATIONS The following chassis, pump, and body specifications shall be strictly adhered to.

Exceptions shall be allowed if they are equal to or superior to that specified (as judged by the customer), and provided they are listed and fully explained on a separate page entitled "EXCEPTIONS TO SPECIFICATIONS". Exception lists shall refer to the specification page number. Each check in the "NO" column shall be listed and fully explained. Where no check is made in a particular paragraph with either "YES" or "NO", it shall be assumed the bidder is taking exception to that paragraph. If a paragraph contains an empty column, where the bidder neglected to check the proper "YES" or "NO" column, it is assumed the bidder is not conforming to the requirements of this paragraph. If no explanation is given in the "EXCEPTIONS TO SPECIFICATIONS" document, the bid is subject to immediate rejection.

PROPOSALS TAKING TOTAL EXCEPTION TO THESE SPECIFICATIONS WILL BE IMMEDIATELY REJECTED.

The buyer is aware that all bidders shall have to take some exceptions therefore; BIDDERS THAT TAKE NO EXCEPTIONS shall BE REQUIRED TO MEET EVERY PARAGRAPH TO THE FULLEST EXTENT SHOULD THEIR BID BE ACCEPTED. It is the intent of the purchaser to receive bids that do not require telephone calls or other communications to ascertain what a bidder is intending to supply.

Upon delivery, the apparatus shall be inspected against THESE specifications and not those supplied by the bidder with their proposal. Deviations shall not be acceptable unless they were noted as exceptions at the time of bid and the apparatus shall be rejected until said deviations are corrected to the satisfaction of the buyer.

Decisions regarding equal to or better than, shall be the sole responsibility of the recipient of the bids rather than those companies submitting bids. All deviations, regardless of significance must be explained in the "EXCEPTIONS TO SPECIFICATIONS" section of the bid.

When exceptions are not taken but inconsistencies are noted in the submitted detailed specifications, the bid may be subject to rejection.

ROADABILITY The apparatus, when fully equipped and loaded, shall be capable of the following performance while on dry paved roads that are in good condition: Quote No: 0015795 Page 4 of 62 October 27, 2015

Smeal Fire Apparatus Co.

• • • •

Accelerating from 0 to 35 mph (55km/hr) within 25 seconds on a 0 percent grade.

Attaining a speed of 50 mph (80 km/hr) on 0 percent grade.

Maintaining a speed of at least 20 mph (32 km/hr) on any grade up to and including 6 percent.

The maximum top speed of the apparatus shall not exceed the tire manufacturer's maximum speed rating for the tires installed on the apparatus.

FAILURE TO MEET TESTS In the event the apparatus fails to meet the test requirements of these specifications on the first trials, second trials may be made at the option of the bidder within 30 days of the date of the first trials.

Such trials shall be final and conclusive and failure to comply with these requirements shall be cause for rejection. Failure to comply with changes as required to conform to any clause of the specifications within 30 days after notice is given to the bidder of such changes, shall be cause for rejection of the apparatus.

Permission to keep or store the apparatus in any building owned or occupied by the Department during the specified period, with the permission of the bidder, shall not constitute acceptance. No Exceptions PROPOSAL SEQUENCE Bid specifications shall be submitted in the same sequence as these specifications for ease of checking compliance. There shall be no exceptions allowed to this requirement.

The apparatus committee intends to be thorough during the evaluation of bids process.

In order to maximize efficiency and minimize the time it takes to thoroughly evaluate all received bids this requirement must be strictly adhered to.

AWARD OF CONTRACT All bids submitted shall be good for a minimum of 30 days during which time bid securities submitted with the proposals shall be held by the purchaser. Criteria for the award shall include, but not be limited to, the following:

• • • • • • • • • • • • •

Apparatus Performance And Safety Levels / Considerations Completeness of proposal Accuracy of accompanying data Past performance of bidder Compliance with the detailed specifications Compliance with purchasers request(s) for personnel qualifications or certifications Exceptions and clarifications Financial stability of bidder Local representation of the manufacturer Serviceability of the proposed apparatus Service capabilities of the bidder's local representative Compliance with NFPA 1901 Any other factor the purchaser deems relevant After the evaluation and award process is complete, all bidders shall be notified of the results and securities shall be returned.

Quote No: 0015795 Page 5 of 62 October 27, 2015

Smeal Fire Apparatus Co.

NFPA 1901-2009 The National Fire Protection Association "Standard for Automotive Fire Apparatus", 2009 edition, is hereby adopted and made a part of these specifications, the same as if it were written out in full detail, with the exception of the section dealing with "Equipment Recommended for Various Types of Apparatus". Bidders shall provide the equipment requested herein and the buyer shall supply the rest before the apparatus is put into service. It is the intent of the purchaser to purchase an apparatus that meets 100% of the minimum standards defined and outlined in NFPA 1901-2009 edition. There are to be no exceptions to this requirement.

PERFORMANCE BOND AND PAYMENT BOND– 100% Smeal Fire Apparatus will provide, within thirty (30) days after award of contract, and along with a signed copy of the contract, a performance bond, which guarantees performance of all terms and conditions of the contract and of the Basic One (1) Year Limited Warranty agreement, and a payment bond, which will guarantee payment for labor, materials, and equipment furnished for use in the performance of the contract. The performance bond will specifically cover the performance of the contract according to its terms and conditions. The payment bond will cover payment of labor, materials, and equipment furnished for use in the performance of the contract. This performance bond and payment bond will be issued by a surety company who is listed by the U.S. Treasury Department’s list of approved sureties, as published in Circular 570, as of the bid date.

The performance bond and payment bond will be issued in an amount equal to 100% of the contract amount and will be dated concurrent to, or subsequent to, the date of the contract.

Notwithstanding any document or assertion to the contrary, any surety bond related to the sale of a vehicle will apply only to the Basic One (1) Year Limited Warranty for such vehicle. Any surety bond related to the sale of a vehicle will not apply to any other warranties that are included within this bid (OEM or otherwise) or to the warranties (if any) of any third party of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. In the event of any contradiction or inconsistency between this provision and any other document or assertion, this provision will prevail.

INSPECTION CERTIFICATE - NFPA 1901 COMPLIANCE A third party inspection certificate for the apparatus shall be furnished upon delivery. The purpose of this NFPA 1901 compliance inspection shall be to serve as proof to the customer that all applicable standards have been met or exceeded by the responsible manufacturer.

The following objectives shall be achieved as a result (this listing shall not be construed October 27, 2015 Quote No: 0015795 Page 6 of 62

Smeal Fire Apparatus Co.

• •

as being all inclusive):

• • • • •

Ensure that understanding of all parties respective responsibilities have been addressed by the actual referencing of NFPA 1901 and the amendments in these specifications and the purchase contract and documentation.

Ensure that only structural materials complying with appropriate standards and codes are used for construction.

Ensure that applicable standards of design and manufacturing have been met or exceeded.

Ensure that safety factors have been met or exceeded where required.

Ensure that applicable standards for testing and inspection have been met or exceeded by personnel with the appropriate qualifications, experience, and certifications.

Ensure that where applicable components, equipment, and loose equipment carry the appropriate characteristics, classifications, and/or certifications.

Ensure that in general and as a whole, all applicable requirements set forth in NFPA 1901, and those codes, standards, and specifications referenced by said parties are met, exceeded, and/or addressed.

CONSTRUCTION DOCUMENTATION The contractor shall supply, at the time of delivery, at least one (1) copy of the following documents:

• • • • • • • •

1. The manufacturers record of apparatus construction details, including the following information:

• • • • • • • • • • •

Owners name and address Apparatus manufacturer, model, and serial number Chassis make, model, and serial number GAWR of front and rear axles Front tire size and total rated capacity in pounds or kilograms Rear tire size and total rated capacity in pounds or kilograms Chassis weight distribution in pounds with water and manufacturer mounted equipment (front and rear) Engine make, model, serial number, rated horsepower and related speed, and governed speed Type of fuel and fuel tank capacity Electrical system voltage and alternator output in amps Battery make, model, and capacity in cold cranking amps (CCA) Chassis transmission make, model, and serial number; and if so equipped, chassis transmission PTO(s) make, model, and gear ratio If applicable, the pump make, model, rated capacity in gallons or liters per minute, and serial number Pump transmission make, model, serial number, and gear ratio, if unit is equipped with a pump If applicable, the auxiliary pump make, model, rated capacity in gallons or liters per minute, and serial number Water tank certified capacity in gallons or liters On aerial apparatus, the device type, rated vertical height in feet or meters, rated horizontal reach in feet or meters, and rated capacity in pounds or kilograms Paint manufacturer and paint number(s) Company name and signature of responsible company representative Quote No: 0015795 Page 7 of 62 October 27, 2015

Smeal Fire Apparatus Co.

2. Certification of slip resistance of all stepping, standing, and walking surfaces 3. If the apparatus has a fire pump, a copy of the following shall be provided: pump manufacturers certification of suction capability, apparatus manufacturers approval for stationary pumping applications, engine manufacturers certified brake horsepower curve showing the maximum governed speed, pump manufacturers certification of the hydrostatic test, and the certification of inspection and test for the fire pump 4. If the apparatus has an aerial device, the certification of inspection and test for the aerial device, and all the technical information required for inspections to comply with NFPA 1914, Standard for Testing Fire Department Aerial Devices 5. If the apparatus has a fixed line voltage power source, the certification of the test for the fixed power source 6. If the apparatus is equipped with an air system, test results of the air quality, the SCBA fill station, and the air system installation 7. Weight documents from a certified scale showing actual loading on the front axle, rear axle(s), and overall fire apparatus (with the water tank full but without personnel, equipment, and hose) 8. Written load analysis and results of the electrical system performance tests 9. When the apparatus is equipped with a water tank, the certification of water tank capacity OPERATION AND SERVICE DOCUMENTATION The contractor shall supply, at time of delivery, at least two (2) sets of complete operation and service documentation covering the completed apparatus as delivered and accepted. The documentation shall address at least the inspection, service, and operations of the fire apparatus and all major components thereof. The contractor shall also provide documentation of the following items for the entire apparatus and each major operating system or major component of the apparatus: Quote No: 0015795 Page 8 of 62 October 27, 2015

Smeal Fire Apparatus Co.

• • • • • • • • • • • • • • • • • • • •

Manufacturers name and address Country of manufacturer Source of service and technical information Parts and replacement information Descriptions, specifications, and ratings of the chassis, pump, and aerial device Wiring diagrams for low voltage and line voltage systems to include the following information: representations of circuit logic for all electrical components and wiring, circuit identification, connector pin identification, zone location of electrical components, safety interlocks, alternator-battery power distribution circuits, and input/ output assignment sheets or equivalent circuit logic implemented in multiplexing systems Lubrication charts Operating instructions for the chassis, any major components such as a pump or aerial device, and any auxiliary systems Precautions related to multiple configurations of aerial devices, if applicable Instructions regarding the frequency and procedure for recommended maintenance Overall apparatus operating instructions Safety considerations Limitations of use Inspection procedures Recommended service procedures Troubleshooting guide Apparatus body, chassis, and other component manufacturers warranties Special data required by this standard Copies of required manufacturer test data or reports, manufacturer certifications, and independent third-party certifications of test results A material safety data sheet (MSDS) for any fluid that is specified for use on the apparatus The contractor shall deliver with the apparatus all manufacturers operations and service documents supplied with components and equipment that are installed or supplied by the contractor.

STATEMENT OF EXCEPTIONS The proposed apparatus as described in this specification document and all related material with the bid package shall meet or exceed all applicable sections for the category of apparatus as defined by NFPA 1901, unless specifically noted within this specification or other official documents associated with this bid.

Should any area, section or portion of the apparatus not meet the intent and applicable requirements, a clearly defined listing or explanation of what and why compliance was not achieved shall be provided to the purchaser at the time of delivery.

OWNER'S MANUAL There shall be an owner's manual containing the construction, operation, and service documentation provided on a USB Drive. There shall be one (1) copy of the USB provided with the apparatus.

ELECTRICAL MANUAL A complete electrical manual for the apparatus shall also be provided on the USB Drive.

Quote No: 0015795 Page 9 of 62 October 27, 2015

Smeal Fire Apparatus Co.

This manual shall be specifically prepared for this individual unit rather than a generic schematic manual designed to accommodate all apparatus. The electrical manual shall also include electrical schematics, harness layouts, V-Mux specifications (including Node Input/output Spreadsheet and Node Relationship Spreadsheet), and Master Wire Listing.

A contact letter shall also be provided by the electrical engineer, who built the manual, with instructions on using the manual and contact information for assistance with electrical manual questions.

ELECTRICAL SCHEMATICS There shall be a section of the electrical manual that shall include schematics of the electrical system and components on the apparatus. These schematics shall be specifically prepared for this individual unit rather than a generic schematic designed to accommodate all apparatus.

PUMP PLUMBING SCHEMATICS (if applicable) There shall be a section of the electrical manual that shall include a schematic of the pump plumbing. This schematic shall be specifically prepared for this individual unit rather than a generic schematic designed to accommodate all apparatus.

HYDRAULIC SCHEMATICS (if applicable) There shall be a section of the electrical manual that shall include schematics of the hydraulic components on the apparatus including but not limited to:

• • • •

Ladder Rack(s) and Hose Bed Door(s) (if applicable) Aerial – Retraction/Extension (if applicable) Aerial – Rotation (if applicable) Tiller – HVAC Hydraulics System (if applicable) FIRE APPARATUS SAFETY GUIDE There shall be one (1) printed copy of the FAMA Fire Apparatus Safety Guide provided with the apparatus.This guide provides safety instructions for operations of the fire apparatus.

MISCELLANEOUS EQUIPMENT ALLOWANCE The Gross Axle Weight Rating (GAWR) and the Gross Combined Weight Rating (GCWR) or Gross Vehicle Weight Rating (GVWR) of the chassis shall be adequate to carry the weight of the unequipped apparatus with the water tank and other tanks full, specified hose load, unequipped personnel weight, ground ladders, and miscellaneous equipment allowance of 1,000 pounds.

TILT TABLE TESTING The apparatus shall be tested to verify the stability to 26.5 degrees in both directions.

The apparatus shall be tested while loaded with fuel, fire fighting agents, hose, ladders, weight of 250 lbs. per seat, and also weight that is equivalent to the miscellaneous equipment that shall be carried. The weight added to the apparatus for testing purposes shall be distributed approximately to the in-service use, yet not to exceed the manufacturer's compartment ratings.

VEHICLE STABILITY Quote No: 0015795 Page 10 of 62 October 27, 2015

Smeal Fire Apparatus Co.

The apparatus shall comply with the requirements of NFPA 1901 as it applies to vehicle stability. The particular apparatus as described in the specification provided within the bid package shall be classified into one of the following categories:

• • •

The apparatus shall go through actual tilt table testing. This shall be determined by the apparatus manufacturer.

The apparatus shall be equipped with a rollover stability control system as defined in section 4.13.1.2 of NFPA 1901.

The apparatus shall be deemed a similar apparatus and meeting the intent of section 4.13.1.1.2 of NFPA 1901.

INDEPENDENT THIRD PARTY PUMP CERTIFICATION The fire pump shall be tested and certified by Underwriter's Laboratories, a nationally recognized independent third party testing company. Tests shall be conducted so that the pump performs as listed below:

• • • •

100% of rated capacity at 150 pounds net pressure 70% of rated capacity at 200 pounds net pressure 50% of rated capacity at 250 pounds net pressure 100% of rated capacity at 165 pounds net pressure The entire pump, both suction and discharge passages, shall be hydrostatically tested to a pressure of 600 PSI. The pump shall be fully tested at the pump manufacturer’s factory to the performance spots as outlined by NFPA 1901. The pump shall be free from objectionable pulsation and vibration.

PUMP CERTIFICATION The pump shall be certified in U.S. gallons per minute (GPM).

FINAL INSPECTION The customer and/or dealer representative will inspect the final apparatus prior to it leaving the apparatus body manufacturer’s facility. This will allow any changes that may be required, to be done so in a timely and inexpensive manner. After leaving the facility, all repairs or alterations will be performed by either the Dealer or an OEM approved service center.

OVERALL HEIGHT The actual overall height of the vehicle shall be approximately 118" (9'-10") from the ground. This measurement shall be taken with the tires properly inflated with the apparatus in the unloaded condition. The actual measurement shall be taken at the highest point of the apparatus.

OVERALL LENGTH The actual overall length of the vehicle shall be approximately 396" (33'-0").

WHEELBASE The actual wheelbase of the vehicle shall be approximately 193" (16'-1").

Quote No: 0015795 Page 11 of 62 October 27, 2015

Smeal Fire Apparatus Co.

ANGLE OF APPROACH The actual angle of approach of the vehicle shall be a minimum of 13 degrees.

ANGLE OF A DEPARTURE The actual angle of departure of the vehicle shall be a minimum of 12 degrees.

SMEAL SIRIUS II CHASSIS The chassis shall be a Smeal Sirius II.

MUD FLAPS In addition to the chassis supplied front mud flaps, there shall be two (2) mud flaps provided rearward of the rear axles on the apparatus. The mud flaps shall be a minimum of 3/8" thick to prevent "sailing." The chassis supplied and installed heat exchanger shall be attached to the pump by the OEM manufacturer.

CHASSIS SUPPLIED FRONT BUMPER The front bumper shall be chassis supplied and installed.

MAP CONSOLE There shall be a map console installed in the chassis cab. The console shall be 10-1/4" wide x 14-3/4" long and 10" deep. The console shall hold three (3) binders up to 3" thick.

The map console shall be constructed of aluminum and shall have an interior and exterior abraded finish.

The map console shall be mounted on the engine tunnel. The map console shall be mounted upright, utilizing a "drop-in" style so the maps are accessible from the top.

HELMET BRACKETS, ZICO The apparatus manufacturer shall supply four (4) helmet brackets in the chassis cab.

The brackets shall meet the 9G requirements of NFPA 1901. The Zico model UHH-1 brackets shall hold both traditional and contemporary style helmets without any adjustments necessary. Storing and removing a helmet that is on the bracket is quick and easy.

STREAMLIGHT RECHARGEABLE LED FIRE VULCANS There shall be four (4) Streamlight, model 44451, high intensity rechargeable LED Fire Vulcans® supplied and installed on the apparatus. Each Vulcan shall feature C4® LED technology with a 50,000 hour lifetime and shall include two (2) bright blue LED taillights, utilizing blinking and steady modes. Each Vulcan shall be orange in color, include one (1) Vehicle Mount System (with quick-release strap), and shall be wired directly to the chassis batteries.

EMS COMPARTMENT - CENTER There shall be a forward-facing EMS compartment installed along the rear interior cab wall in the center of the chassis. The compartment shall be 48" tall, 32" wide, and 18" Quote No: 0015795 Page 12 of 62 October 27, 2015

Smeal Fire Apparatus Co.

deep. The compartment shall be constructed of aluminum. There shall be two (2) adjustable aluminum shelves, with abraded finish, provided in the compartment.

The compartment shall have a ROM roll-up door provided on the front for easy access to equipment stored inside. The roll up door shall be supplied with a full-width handle for ease of opening with only one hand, allowing quick access to equipment and nylon end shoes on every slat to assure operation without constant lubrication. There shall be a door lock with key provided with the roll-up type door.

The EMS compartment shall be furnished with a LED compartment light mounted on the front corner of the compartment. An automatic door switch shall activate the compartment light.

The EMS compartment exterior shall be coated with gray Line-X®, a thermoplastic polyurethane coating.

ALUMINUM MOUNTING PLATE ON ENGINE TUNNEL There shall be an 1/8" aluminum mounting plate on the top of the chassis engine tunnel for the mounting of equipment. The plate shall be mounted on 3/4" spacers and will be on the flat portion of the engine tunnel only. The mounting plate shall have an abraded finish.

120V RECEPTACLE OUTLET BAR There shall be one (1) 120 volt receptacle outlet bar installed on the apparatus. The outlet bar shall have six (6) 120 volt receptacles and wired directly to the shoreline.

The outlet shall be located inside the EMS compartment.

WATER TANK The apparatus shall be equipped with a United Plastic Fabricating 1000 U.S. gallon water tank. Certification of the tank capacity shall be recorded on the manufacturer's record of construction and shall be provided to the purchaser upon delivery of the apparatus. The UPF® water tank shall be constructed of 1/2" thick PT2E™ polypropylene sheet stock. This material shall be a non-corrosive stress relieved thermoplastic, black in color, and U.V. stabilized for maximum protection.

BOOSTER TANK The booster tank shall be of a specific configuration and shall be so designed to be completely independent of the body and compartments. All joints and seams shall be nitrogen welded and tested for maximum strength and integrity. The top of the booster tank shall be fitted with removable lifting eyes designed with a 3 to 1 safety factor to facilitate easy removal.

TANK BAFFLES The transverse swash partitions shall be manufactured of 3/8" PT2E™ polypropylene (natural in color) and extend from approximately 4" off the floor to just under the cover.

The longitudinal swash partitions shall be constructed of 3/8" PT2E polypropylene (natural in color) and extend to the floor of the tank through the cover to allow for positive welding and maximum integrity. All partitions shall be equipped with vent and air holes to Quote No: 0015795 Page 13 of 62 October 27, 2015

Smeal Fire Apparatus Co.

permit movement of air and water between compartments. The partitions shall be designed to provide maximum water flow. All swash partitions shall interlock with one another and be welded to each other as well as to the walls of the tank.

TANK SUMP There shall be one (1) sump in the bottom of the water tank. The sump shall be constructed of 1/2" polypropylene and shall be located in the left front quarter of the tank.

On all tanks that require a front suction, a 4" schedule 40 polypropylene pipe shall be installed that will incorporate a dip tube from the front of the tank to the sump location.

The sump shall be used as a combination clean-out and drain. All tanks shall have an anti-swirl plate located approximately 2" above the sump to pre-vent air from being entrained in the water while pumping.

TANK FILL CONNECTION All tank fill couplings shall be backed with flow deflectors to break up the stream of water entering the tank, and shall be capable of withstanding sustained fill rates of up to 1,000 GPM.

TANK LID The tank lid shall be constructed of 1/2" thick PT2E™ polypropylene to incorporate a multi three-piece locking design that allows for individual removal and inspection if necessary. The tank lid shall be recessed 3/8" from the top of the tank and shall be welded to both sides and longitudinal partitions for maximum integrity. Each one of the lids shall have hold downs consisting of 2" polypropylene dowels spaced a maximum of 30" apart. These dowels shall extend through the covers and shall assist in keeping the covers rigid under fast filling conditions. A minimum of two lifting dowels shall be drilled and tapped 1/2" x 13" to accommodate the lifting eyes.

WATER TANK MOUNTING The water tank cradle shall be an integral part of the body sub-frame. Please reference the sub-frame section for complete water tank mounting information.

WATER TANK DRAIN There shall be a 1-1/2" drain valve provided under the sump of the water tank. The valve shall include a locking lever to prevent accidental draining of the water tank.

WATER TANK FILL TOWER The tank shall have a combination vent and manual fill tower marked "Water Fill." The fill tower shall be constructed of 1/2" PT2E™ polypropylene and shall be a minimum dimension of 8" x 8" at the outer perimeter. The tower shall be located in the left front corner of the tank. The tower shall have a 1/4" thick removable polypropylene screen and a PT2E™ polypropylene hinged-type cover. The fill tower shall be black in color.

WATER TANK LEVEL GAUGE There shall be one (1) Innovative Controls SL Plus Tank Level Monitor System provided on the pump operator's control panel. The system shall include one (1) electronic display module(s), a stainless steel pressure transducer sender unit, and the necessary wiring Quote No: 0015795 Page 14 of 62 October 27, 2015

Smeal Fire Apparatus Co.

with water-tight plug terminations that do not require sealing grease.

The master display module shall show the tank level using 16 super-bright easy-to-see LEDs. Tank level indication shall be achieved by the appropriate illumination of 4 horizontal rows of LEDs, with 4 LEDs per row. Full and near-full levels shall be indicated with the illumination of all 4 rows of LEDs, including the illumination of the top row of 4 green LEDs. Tank levels between ½ and ¾ full shall be indicated with the illumination of the bottom 3 rows of LEDs, including the illumination of the top row of 4 blue LEDs. Tank levels between ¼ and ½ full shall be indicated with the illumination of the bottom 2 rows of LEDs, including the illumination of the top row of 4 amber LEDs. Tank levels between ¼ full and near empty shall be indicated with the illumination of the bottom row of 4 red LEDs only. Tank levels between near empty and empty shall be indicated by flashing the bottom row of 4 red LEDs.

The master display shall have a backlit area above at the top with illuminated water icon and a backlit area at the bottom with illuminated OEM logo.

A wide-angle polycarbonate diffusion lens in front of the LEDs shall produce a 180° viewing angle. The electronic display module shall be waterproof and shock resistant being encapsulated in a urethane-based potting compound. The potted display electronics shall be integral to a chrome-plated panel-mount reflector that is secured to the apparatus panel with 4 screws installed from the inside of the panel.

All programming functions shall be accessed and performed from the front of the installed master display module with a magnet. The programming shall include manual or self-calibration for any style tank.

CHASSIS SUPPLIED PSTANK WATER LEVEL DISPLAY ON LEFT AND RIGHT SIDES There shall be a Whelen model PSTANK LED water level display installed on the left and right side of the chassis cab by the chassis manufacturer. The apparatus manufacturer shall install an Innovative Controls relay driver module to power the PSTANK displays. The module shall receive data from the master water tank level gauge and mimic the master display. The color of the LED lights shall be green, blue, amber and red.

4" WATER TANK OVERFLOW The tank shall be equipped with a minimum of a 4" schedule 40 polypropylene overflow/ air vent pipe. The pipe shall be installed in the fill tower and extend through the tank and dump to the rear of the rear axle.

FOAM CELL There shall be one (1) United Plastic Fabricating 30 U.S. gallon foam cell incorporated into the water tank. There shall be one (1) pressure/vacuum vent installed on the foam tank. There shall be one (1) drain hose connected to the foam cell. The drain shall have a quarter-turn valve installed inside the pump compartment and it shall drain below the frame rail of the chassis.

Class "A" foam shall be utilized.

Quote No: 0015795 Page 15 of 62 October 27, 2015

Smeal Fire Apparatus Co.

The foam tank shall have a manual fill tower. The fill tower shall be constructed of 1/2" PT3™ polypropylene and shall be a minimum dimension of 8" x 8" outer perimeter. Each foam fill tower shall be constructed of a black colored material indicating which tower is to receive each type of foam utilized. The capacity of the tank shall be engraved on the top of the fill tower lid. The tower shall be located in the right front corner of the tank unless otherwise specified. The tower shall have a 1/4" thick removable polypropylene screen and a stainless steel hinged-type cover. Inside the fill tower, approximately 1.5” down from the top, there shall be an anti-foam fill tube that extends down to the bottom of the tank. A pressure vacuum vent shall be provided in the lid of the fill tower.

FOAM TANK LEVEL GAUGE There shall be one (1) Innovative Controls SL Plus Tank Level Monitor System for indicating Class A foam level provided on the pump operator's control panel. The system shall include one (1) electronic display module, a stainless steel pressure transducer sender unit, and the necessary wiring with water-tight plug terminations that do not require sealing grease.

The master display module shall show the foam tank level using 16 super-bright easy-to see LEDs. Tank level indication shall be achieved by the appropriate illumination of 4 horizontal rows of LEDs, with 4 LEDs per row. Full and near-full levels shall be indicated with the illumination of all 4 rows of LEDs, including the illumination of the top row of 4 green LEDs. Tank levels between ½ and ¾ full shall be indicated with the illumination of the bottom 3 rows of LEDs, including the illumination of the top row of 4 blue LEDs. Tank levels between ¼ and ½ full shall be indicated with the illumination of the bottom 2 rows of LEDs, including the illumination of the top row of 4 amber LEDs. Tank levels between ¼ full and near empty shall be indicated with the illumination of the bottom row of 4 red LEDs only. Tank levels between near empty and empty shall be indicated by flashing the bottom row of 4 red LEDs.

The master display shall have a backlit area above at the top with illuminated foam A icon and a backlit area at the bottom with illuminated OEM logo.

A wide-angle polycarbonate diffusion lens in front of the LEDs shall produce a 180° viewing angle. The electronic display module shall be waterproof and shock resistant being encapsulated in a urethane-based potting compound. The potted display electronics shall be integral to a chrome-plated panel-mount reflector that is secured to the apparatus panel with 4 screws installed from the inside of the panel.

All programming functions shall be accessed and performed from the front of the installed master display module with a magnet. The programming shall include manual or self-calibration for any style tank.

HOSE BED The hose bed shall be located above the water tank and have a minimum capacity of 30 cubic feet in accordance with the latest NFPA regulations. The inside of the hose bed shall be smooth aluminum. The hose bed shall exit at the rear of the apparatus through a single access opening. The opening shall be free of obstructions that might interfere with the deployment and loading of hose. There shall be a 1" stainless steel trim piece on the body, at the rear-bottom of the hose bed, to protect the chevron when deploying hose and shall be attached using fasteners.

The interior of the hose bed shall be painted the same body color as the upper portion of Quote No: 0015795 Page 16 of 62 October 27, 2015

Smeal Fire Apparatus Co.

the body.

The floor of the hose bed compartment shall be constructed of Dura-Dek fiber reinforced plastic material. The flooring shall be fabricated of "T" beam protrusions in parallel connected with cross slats that are first mechanically bonded and then epoxied, forming a large sheet. The top portion of each "T" cross section shall measure 1-1/4" wide and 3/16" thick with beaded ends. The vertical portion shall be 3/8" thick, beading out at the bottom to a thickness of 1/2" and tall enough to result in an overall height of 1". The "T" sections shall be spaced 3/4" apart to allow for drainage and ventilation.

Each "T" beam shall be constructed utilizing a core of 250,000 continuous glass fiber strands that are high in resistance to tension, compression and bending. An outer sheath consisting of a continuous strand mat to prevent lineal splitting and slipping shall surround the core. The sheath shall also serve to draw the protective resin to the bar surface. Both reinforcements shall be pulled through an isophthalic polyester resin, treated with antimony trioxide for fire resistance, to form a solid length.

The flooring shall then be protected with a polyurethane coating to screen out ultraviolet rays. This bright white coating shall be baked on and shall provide a pleasing contrast when installed in the apparatus.

The hose bed shall be contain the following hose load: 200' of 2-1/2" double jacket hose 1000' of 5" double jacket hose 300' of 2-1/2" double jacket hose HOSE BED COVER There shall be a heavy-duty 22 oz. hypalon vinyl coated nylon hose bed cover installed on the apparatus. The front edge of the cover shall be retained in a "C" channel to prevent wind from lifting it. The sides of the cover shall be attached to the sides of the hose bed utilizing hooks and bungee cord. The rear of the cover shall be attached to the body utilizing hooks and bungee cord. The cover color shall be black.

HOSE BED DIVIDERS There shall be two (2) hose bed dividers installed in the hose bed. The dividers shall be fabricated from 1/4" smooth aluminum plate and an aluminum extrusion. Each divider shall have an abraded finish and mounted on hot-dipped galvanized slide rails at the front and rear of the hose bed. Where no obstruction such as a fill tower is present, the slide rails shall allow full movement of the dividers along the width of the hose bed. Each hose bed divider shall have an oval shaped hand hold slot to assist in moving the divider.

This shall provide the capability for variable hose load configurations and capacities.

HOSE BED LOADING LIGHTS There shall be two (2) Grote Trilliant, model 63901 hose bed loading lights provided on the rear of the apparatus. The light shall have an "Aim-N-Go" feature that requires no tools for horizontal adjustments. The Trilliant light shall delivers 35,000 hours of operation and beam patterns can be changed easily with optional replacement lenses.

The light output shall be 150,000 candelas with an amp draw of 4.2. Each light shall include a bolt on bracket.

Quote No: 0015795 Page 17 of 62 October 27, 2015

Smeal Fire Apparatus Co.

ALUMINUM BODY CONSTRUCTION The apparatus body shall be fabricated from 1/8" 5052-H32, smooth aluminum sheet.

The total outside width of the apparatus body shall not exceed 100 inches (2.54 meters).

The width measurement of the sidewalls shall be made from the outside wall of the two opposite sides of the body. The body shall be designed for a single axle chassis.

The complete apparatus body shall be fabricated utilizing the break and bend techniques in order to form a strong, yet flexible, uni-body structure. The body shall be constructed with holding fixtures to ensure proper dimensioning. Each apparatus body is specific in design in order to meet the unique requirements of the purchasing fire department.

The main body compartments on each side, as well as the rear center compartment if applicable, shall contain a sweep out floor design. Each compartment shall be made to the most practical dimensions in order to provide maximum storage capacity for the fire department's equipment. The door opening threshold shall be positioned lower than the compartment floor permitting easy cleaning of the compartments.

Continuous, solid welded seams shall be located at the upper front and upper rear corners of the apparatus body. The flooring of all lower, main body compartmentation shall also have solid weld seams. All door jams, on both the top and the bottom, shall be solid welded as well. Each main door jam shall consist of a double jam design; this is comparable to a double struck frame design, which provides superior strength and durability. All double door jams are to be welded together utilizing the plug weld technique. All remaining compartment walls shall be stitch welded.

The compartment floors, specifically L1 and R1, shall have a minimum of two (2) 2" x 1/4" angles welded to the entire width of the compartment floor. The two (2) rear side compartments as well as the rear center compartment, if applicable, shall be welded to the rear deck support structure. This rear deck support structure is specially designed for the galvanized apparatus body substructure. A minimum of two (2) angles, which are 1/4" x 3" x 3", shall run the entire width of the body from sidewall to sidewall. Each lower, rear compartment shall be adequately stitch welded to the cross angles providing strength and durability to the entire apparatus body.

The body design shall include a "false wall" design in the lower portion of each lower, rear compartment. This "false wall" is required in order to allow for easy accessibility to the rear electrical components found in the rear tail light cluster area.

On the upper area of the apparatus body, directly above the side compartment door openings, a header is to be fabricated from smooth, aluminum sheet. This area shall be free from any body seams and shall be painted the same color as the apparatus body.

The height of the header may vary depending on the following factors: apparatus design, lettering requirements, scene lights and warning light requirements as well as various other options. A "J" channel shall be incorporated into the body design in order to provide a rain gutter to further assist in preventing excessive moisture from getting into the compartments.

There shall be one (1) ROM rollup door installed on each side body compartment face.

Each door shall be a shutter type with 34 millimeter slats that roll onto a spool at the top of the compartment. Each slat shall be equipped with nylon end shoes to assure operation without the need of constant lubrication. Each rollup door shall have a satin finish.

Quote No: 0015795 Page 18 of 62 October 27, 2015

Smeal Fire Apparatus Co.

Each ROM rollup door shall be supplied with a full width lift bar and finger pull handle integrated into the bottom rail for easy one hand operation.

The door handles on the side body compartments of the apparatus shall be non-locking style.

There shall be splash guards/drip pans installed inside the upper section of all body compartments with roll-up doors. Each aluminum drip pan shall catch drops of water that accumulate on the shutter and drip into the shutter compartment when the door is being rolled up. Each plastic splash guard shall act to keep water from being splashed throughout the interior of the compartment while the door is being rolled up. The pans shall also serve to protect the shutter from damage due to impact from behind or below.

REAR COMPARTMENT DOOR There shall be one (1) ROM rollup door installed on the T1 compartment face. The door shall be a shutter type with 34 millimeter slats that roll onto a spool at the top of the compartment. Each slat shall be equipped with nylon end shoes to assure operation without the need of constant lubrication. The roll-up door shall have a satin finish.

The ROM rollup door shall be supplied with a full width lift bar and finger pull handle integrated into the bottom rail for easy one hand operation.

BODY COMPARTMENT LIGHTING There shall be a total of eleven (11) ROM V4 LED compartment lights installed in the body compartments. Each light shall feature solid state construction and be waterproof to IPX7 rating. The V4 LED lights shall offer 250 lumens per foot of lighting.

COMPARTMENT COATING The interior of the body compartments shall be coated with gray Line-X®. thermoplastic polyurethane coating, unless otherwise specified. The coating shall be durable enough to withstand every day abuse of equipment removal and shifting.

TURTLE TILES There shall be Turtle Tile Plastics interlocking squares in all of the body compartments.

The Turtle Tiles shall be applied in all body compartment shelves, adjustable-height trays, floor-mounted trays, and on compartment floors that do not contain floor-mounted trays. No Turtle Tiles shall be applied on compartment floors underneath floor-mounted trays. Each square shall be made from polyvinyl chloride that is flame and chemical resistant. For maximum slip resistance and drainage, each square shall have a grid surface design.

COMPARTMENT AIR RELEASE Each compartment shall be vented to help remove trapped air when closing a compartment door. The vent shall be a rubber gasket in the area of the outboard corners of the compartment. Wiring may also be run through these areas.

COMPARTMENT DRAIN HOLES Each body compartment shall be equipped with drain holes to allow standing water to exit to underneath the apparatus.

Quote No: 0015795 Page 19 of 62 October 27, 2015

Smeal Fire Apparatus Co.

HANDRAILS All handrails, unless otherwise stated, shall be constructed of knurled aluminum of not less than 1-1/4" in diameter. All railing shields and brackets shall be chrome plated, and shall be bolted to the body with stainless steel bolts. The lower bracket on all vertical handrails shall have a drain hole drilled in it at the lowest point.

The following handrails shall be provided on the apparatus: FUEL FILL The fuel fill pocket shall be located in the rear triangular shaped SCBA air bottle compartment on the driver's side of the apparatus. The cap of the fuel fill shall be a click type plastic cap. The interior of the compartment will be divided into two (2) individual storage areas to accommodate two (2) air bottles and the lower corner shall house the fuel fill.

DRIVER'S (LEFT) SIDE BODY COMPARTMENTS COMPARTMENT L1 There shall be a full height compartment located ahead of the rear wheels on the driver's side of the apparatus body. This compartment shall be designated as L1 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 61" Width: 35" Depth: 26" Upper and 26" Lower Intermediate Divide Height: 0" COMPARTMENT L2 There shall be a standard height compartment located above the rear wheels on the driver's side of the apparatus body. This compartment shall be designated as L2 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 28.5" Width: 65" Depth: 26" Upper and 0" Lower Intermediate Divide Height: 0" COMPARTMENT L3 There shall be a full height compartment located behind the rear wheels on the driver's side of the apparatus body. This compartment shall be designated as L3 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 61" Width: 42" Depth: 26" Upper and 26" Lower Intermediate Divide Height: 0" L1 Components Quote No: 0015795 Page 20 of 62 October 27, 2015

Smeal Fire Apparatus Co.

There shall be one (1) aluminum adjustable full-depth shelf installed on the apparatus in the compartment. The shelf shall be constructed of 3/16" aluminum sheet with 2" lips.

The shelf shall be coated with abraded finish and shall be designed in such a manner as to allow liquids to readily drain when spilled.

There shall be one (1) roll out equipment tray installed on the floor of the compartment.

The tray shall be equipped with an Austin Hardware drawer slide. The roller assembly shall have a rated capacity of 300 lbs. distributed load and shall have 100% extension capability. The tray shall be constructed of 3/16" aluminum sheet with 3" lips to prevent items from being shifted during transportation. The tray shall be equipped with the Austin Hardware front drawer release system, which allows for one handed latch closed position release. The tray shall have an abraded finish and shall be equipped with a locking slide in order to hold the tray in either a fully extended or closed position.

There shall be one (1) aluminum mounting plate installed on the back wall of the compartment. The plate shall be spaced away from the back wall of the compartment with uni-strut channels, which shall also be used as an easy means of removing the plate to mount equipment brackets. The plate shall be constructed of 3/16", 5052-H32 aluminum and have an abraded finish.

There shall be aluminum vertical strut channels welded in the compartment. There shall be two (2) struts on each side of the compartment The compartment layout shall be detailed at the pre-construction meeting.

L2 Components There shall be one (1) split swing out aluminum tool board located in the standard height compartment. The tool board shall be constructed of 3/16" aluminum. The tool board shall be mounted to adjustable unistruts to allow each side of the tool board to be relocated for depth in the compartment. There shall be an adjustable positive latching mechanism mounted to the ceiling and the floor of the compartment that shall secure each side of the tool board in the close position. The tool board shall utilize a friction washers to hold them in both the opened and closed position.

The tool board shall have a maintenance-free abraded finish and be of a pegboard pattern design.

The compartment layout shall be detailed at the pre-construction meeting.

L3 Components There shall be three (3) full height, slide out aluminum tool boards provided in the full depth compartment. Each tool board shall utilize a pneumatic cylinder to hold the tool board in both the opened and closed position. Each tool board shall be mounted to an adjustable unistrut to allow the boards to be relocated for best fit in the compartment.

The tool boards shall have a maintenance-free abraded finish and be of a pegboard pattern design.

The compartment layout shall be detailed at the pre-construction meeting.

DRIVER'S SIDE REAR WHEEL WELL POSITION - WL1 There shall be a three (3) air bottle compartment installed in the forward portion of the rear wheel well area, on the driver's side. The compartment shall be a triangle design.

Quote No: 0015795 Page 21 of 62 October 27, 2015

Smeal Fire Apparatus Co.

The compartment door and hinges shall be constructed out of stainless steel material, and the frame shall be constructed out of aluminum. The door shall have a rubber gasket in order to create a 100% seal to protect the interior of the compartment. The storage compartment shall be a rotational, molded component that is assembled to the door and frame. This assembly process shall prevent the air bottle from making contact with the stainless steel frame while loading and unloading the air bottle. The door shall be painted primary body color.

DRIVER'S SIDE REAR WHEEL WELL POSITION - WL3 There shall be a two (2) air bottle compartment installed in the rearward portion of the rear wheel well area, on the driver's side. The compartment shall be a triangle design.

The compartment door and hinges shall be constructed out of stainless steel material, and the frame shall be constructed out of aluminum. The door shall have a rubber gasket in order to create a 100% seal to protect the interior of the compartment. The storage compartment shall be a rotational, molded component that is assembled to the door and frame. This assembly process shall prevent the air bottle from making contact with the stainless steel frame while loading and unloading the air bottle. The door shall be painted primary body color.

OFFICER'S (RIGHT) SIDE BODY COMPARTMENTS COMPARTMENT R1 There shall be a full height compartment located ahead of the rear wheels on the officer's side of the apparatus body. This compartment shall be designated as R1 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 61" Width: 35" Depth: 15" Upper and 26" Lower Intermediate Divide Height: 27" COMPARTMENT R2 There shall be a standard height compartment located above the rear wheels on the officer's side of the apparatus body. This compartment shall be designated as R2 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 28.5" Width: 65" Depth: 15" Upper and 0" Lower Intermediate Divide Height: 0" COMPARTMENT R3 There shall be a full height compartment located behind the rear wheels on the officer's side of the apparatus body. This compartment shall be designated as R3 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 61" Width: 42" Depth: 15" Upper and 26" Lower Intermediate Divide Height: 27" Quote No: 0015795 Page 22 of 62 October 27, 2015

Smeal Fire Apparatus Co.

R1 Components There shall be one (1) aluminum adjustable shallow-depth shelf installed on the apparatus in the compartment. The shelf shall be constructed of 3/16" aluminum sheet with 2" lips. The shelf shall have a abraded finish and shall be designed in such a manner as to allow liquids to readily drain when spilled.

There shall be aluminum vertical strut channels welded in the compartment. There shall be two (2) struts on each side of the compartment The compartment layout shall be detailed at the pre-construction meeting.

R2 Components There shall be one (1) PAC TRAC tool mounting section installed on the back wall of the compartment. The PAC TRAC section shall be constructed of 7/8" thick, 6063-T5 extruded aluminum.

The compartment layout shall be detailed at the pre-construction meeting.

R3 Components There shall be one (1) aluminum adjustable shallow-depth shelf installed on the apparatus in the compartment. The shelf shall be constructed of 3/16" aluminum sheet with 2" lips. The shelf shall have a abraded finish and shall be designed in such a manner as to allow liquids to readily drain when spilled.

There shall be one (1) roll out equipment tray installed on the floor of the compartment.

The tray shall be equipped with an Austin Hardware drawer slide. The roller assembly shall have a rated capacity of 300 lbs. distributed load and shall have 100% extension capability. The tray shall be constructed of 3/16" aluminum sheet with 3" lips to prevent items from being shifted during transportation. The tray shall be equipped with the Austin Hardware front drawer release system, which allows for one handed latch closed position release. The tray shall have an abraded finish and shall be equipped with a locking slide in order to hold the tray in either a fully extended or closed position.

There shall be aluminum vertical strut channels welded in the compartment. There shall be two (2) struts on each side of the compartment The compartment layout shall be detailed at the pre-construction meeting.

OFFICER'S SIDE REAR WHEEL WELL POSITION - WR1 There shall be a three (3) air bottle compartment installed in the forward portion of the rear wheel well area, on the officer's side. The compartment shall be a triangle design.

The compartment door and hinges shall be constructed out of stainless steel material, and the frame shall be constructed out of aluminum. The door shall have a rubber gasket in order to create a 100% seal to protect the interior of the compartment. The storage compartment shall be a rotational, molded component that is assembled to the door and frame. This assembly process shall prevent the air bottle from making contact with the stainless steel frame while loading and unloading the air bottle. The door shall be painted primary body color.

OFFICER'S SIDE REAR WHEEL WELL POSITION - WR3 There shall be a three (3) air bottle compartment installed in the rearward portion of the Quote No: 0015795 Page 23 of 62 October 27, 2015

Smeal Fire Apparatus Co.

rear wheel well area, on the officer's side. The compartment shall be a triangle design.

The compartment door and hinges shall be constructed out of stainless steel material, and the frame shall be constructed out of aluminum. The door shall have a rubber gasket in order to create a 100% seal to protect the interior of the compartment. The storage compartment shall be a rotational, molded component that is assembled to the door and frame. This assembly process shall prevent the air bottle from making contact with the stainless steel frame while loading and unloading the air bottle. The door shall be painted primary body color.

REAR SIDE BODY COMPARTMENTS COMPARTMENT T1 There shall be a full height compartment located at the rear of the apparatus body. This compartment shall be designated as T1 within these specifications and any ensuing paperwork or drawings after contract execution.

The dimensions of the compartment shall be: Height: 42" Width: 41" Depth: " T1 Components There shall be one (1) aluminum adjustable full-depth shelf installed on the apparatus in the compartment. The shelf shall be constructed of 3/16" aluminum sheet with 2" lips.

The shelf shall be coated with abraded finish and shall be designed in such a manner as to allow liquids to readily drain when spilled.

There shall be one (1) roll out equipment tray installed on the floor of the compartment.

The tray shall be equipped with a Hansen International drawer slide. The roller assembly shall have a rated capacity of 300 lbs. distributed load and shall have 100% extension capability. The tray shall be constructed of 3/16" aluminum sheet with 3" lips to prevent items from being shifted during transportation. The tray shall have an abraded finish and be equipped with a gas spring in order to hold the tray in either a fully extended or closed position.

There shall be aluminum vertical strut channels welded in the compartment. There shall be two (2) struts on each side of the compartment The compartment layout shall be detailed at the pre-construction meeting.

GS-36 BODY SUB FRAME To assure proper body alignment and clearance, the body sub frame shall be constructed in a jig and fitted directly on the chassis. The sub frame shall be constructed of 36,000 PSI galvanized steel.

The chassis frame rails shall be fitted with fiber reinforced rubber to isolate the body frame members from direct contact with chassis frame rails.

The main body sub frame shall be constructed from steel tubing. The sub frame shall run the full length of the body and shall be spaced the same width as the chassis frame rails.

The main sub frame shall also be the integral support for the water tank. Vertical drop tubes shall be welded to the sub frame. From these vertical drop tubes shall extend cross members constructed of steel angle. These cross members shall extend out to Quote No: 0015795 Page 24 of 62 October 27, 2015

Smeal Fire Apparatus Co.

support the compartments. Cross members shall be located at the front and rear of the body and in front and rear of the wheel well opening.

A drop frame, fabricated of steel tube and steel angles, shall support the compartment area behind the rear. The rear drop frame shall be constructed using vertical drop tubes, welded to the main sub frame. All drop frame structures shall be welded directly to the body sub frame to allow the body to be a completely separate structure from the chassis.

After fabrication the sub frame shall be hot dip galvanized for maximum protection against corrosion.

BODY MOUNTING The body sub frame shall be fastened to the chassis frame with a minimum of six (6) spring loaded body mounts. Each mount shall be configured using a two-piece bracket.

The two (2) brackets shall be fabricated of steel plates. The plates shall be galvanized to prevent any corrosion. Each mounting assembly shall utilizing two (2) plated bolts and two (2) heavy duty springs. The assembly design shall allow the body and sub frame to act as one (1) component, separate from the chassis. As the chassis frame twists under driving conditions, the spring mounting system shall limit any stress from being transferred into the body. The spring loaded body mounts shall also prevent frame side rail or body damage caused by unevenly distributed stress and strains due to load and chassis movement.

Body mountings that do not allow relief from chassis movement shall not be acceptable.

TANK MOUNTING The water tank shall rest on the sub frame cross members which are spaced as required by the tank manufacturer.

The tank shall be isolated from the cross members through the use of hard rubber strips with a minimum Rockwell hardness of 60 durometer. Additionally, the tank shall be supported around the entire perimeter and captured front and rear as well as side to side to prevent the tank from shifting during vehicle operations.

Although the tank shall be designed on a free floating suspension principle, it shall be required that the tank have adequate hold down restrains to minimize movement during vehicle operations.

The tank shall be completely removable without disturbing or dismantling the apparatus structure.

WALKWAYS AND OVERLAYS All exterior surfaces designated by the manufacturer as stepping, standing, or walking areas shall be overlaid with 3003 H22 Bright Tread Plate to provide a slip resistant surface, even when the surface is wet. All interior surfaces designated by the manufacturer as stepping, standing, or walking areas shall be slip resistant when the surface is dry. The degree of slip resistance shall be in compliance with the intent of NFPA 1901.

Horizontal walkways shall have .080" aluminum tread plate overlays installed and Quote No: 0015795 Page 25 of 62 October 27, 2015

Smeal Fire Apparatus Co.

vertical surfaces shall have .125” aluminum overlays. Overlays shall be installed that are totally insulated from the apparatus with nylon shoulder washers that extend into holes in the body. Stainless steel cap nuts shall be employed where bolt ends may damage equipment or cause injury. After the apparatus is painted and the overlays are reinstalled, they shall be additionally sealed at the edges with a caulking compound. The exterior top tread plate overlay shall be mounted flush with the outer edges of the apparatus body.

STEPPING SURFACES All steps shall have a surface area of at least 35 square inches and shall be able to withstand a load of at least 500 pounds. Steps shall be provided at any area that personnel may need to climb and shall be adequately lighted.

REAR DECK A modular bolt-on deck shall be installed on the rear of the apparatus to form a full width step area. The rear deck shall be constructed of anti-slip bright tread plate. The outside edge of the rear deck shall be flush with the rub rail that is installed on the body to maintain a uniform appearance. The depth of the rear deck shall be 13.25”. The rear deck shall be installed with sufficient support to form a sturdy, non-deflecting step area for personnel.

AUXILIARY STEP BELOW REAR DECK There shall be an auxiliary step located below the rear deck to assist in the safe climbing onto the apparatus.

BODY RUB RAILS Rub rails shall be installed beneath the compartment doors to protect them from damage should the body be brushed or rubbed against another object. The rub rails shall be 3/16” aluminum channel, 2-1/2” x 1”. The rub rails shall be highly polished and then bright dip anodized.

The rub rails shall be installed on the body utilizing non-corrosive nylon spacers and secured with stainless steel bolts. The outside edge of the rub rails shall be even with the fenderettes and bolt-on steps to prevent snagging.

REAR UNDERBODY TOW EYE One (1) rear tow eye shall be installed directly below the rear of the chassis frame rails, mounted to the subframe. The tow eye shall be capable of a 15,000 lb. straight pull rating.

REAR WHEEL WELLS The fenders shall be integral with the body sides and compartments with a seamless appearance. The fenders shall be fitted with bolt-in removable full circular inner liners in the wheel well area for ease of cleaning and maintenance. There shall be sufficient clearance provided in the wheel well to allow the use of tire chains when the apparatus fully loaded.

Quote No: 0015795 Page 26 of 62 October 27, 2015

Smeal Fire Apparatus Co.

STAINLESS STEEL REAR FENDERETTES Two (2) stainless steel fenderettes shall be installed at the outboard edge of the rear wheel well area, one (1) on each side. The fenderettes shall be bolted to the apparatus body using nylon washers to space them slightly away from the body to reduce build-up of road grime. The fenderettes shall be constructed of stainless steel that has been polished to a high quality finish.

EXHAUST HEAT DEFLECTOR SHIELD There shall be a 4" heat deflector shield installed over the exhaust to aid in dissipating the heat to prevent exhaust heat from adversely affecting anything stored in the body.

FUEL TANK GAUGE ACCESS PANEL There shall be a removable panel provided in the rear compartment to allow for access to the fuel tank gauge without removing the fuel tank.

LICENSE PLATE BRACKET There shall be a license plate bracket mounted on the rear of the apparatus. A clear LED light shall be incorporated into the bracket.

TRIMRITE® STAINLESS STEEL FASTENERS TrimRite® stainless steel fasteners shall be provided for all exposed and unpainted fasteners throughout the body in locations such as overlays, pump panels, and other numerous hardware mounting locations. TrimRite® stainless is a hardenable martensitic stainless steel that provides a high level of corrosion resistance, hardness up to Rockwell C 51, good cold formability and ease of heat treatment, all of which combine to provide an alloy which has been used for many applications such as fasteners, especially self-drilling types. TrimRite® stainless are tested to salt spray standard ASTM B117, which is a 200-hour salt spray test. The OEM shall use TrimRite® stainless with an added blue patch which provides improved vibration resistance for the fastener.

ADDITIONAL HARDWARE There shall be a bag of stainless steel nuts, bolts, and washers supplied with the apparatus for mounting of equipment.

FRONT BODY STEPS AND LIGHTING There shall be four (4) Cast Products folding steps located on the front of the driver's side body compartments. The folding steps shall have two large open slots to prevent the buildup of ice or mud and to provide a handhold when necessary. The steps shall have a surface area of at least 35 square inches and shall be able to withstand a load of 500 pounds.?

The steps shall be adequately lit with LED lighting. There shall be one (1) light located above the steps.

There shall be a handrail installed forward on the top of the body, on the driver's side.

Quote No: 0015795 Page 27 of 62 October 27, 2015

Smeal Fire Apparatus Co.

FRONT BODY STEPS AND LIGHTING There shall be four (4) Cast Products folding steps located on the front of the officer's side body compartments. The folding steps shall have two large open slots to prevent the buildup of ice or mud and to provide a handhold when necessary. The steps shall have a surface area of at least 35 square inches and shall be able to withstand a load of 500 pounds.?

The steps shall be adequately lit with LED lighting. There shall be one (1) light located above the steps.

There shall be a handrail installed on the top officer's side front of the body.

FRONT VERTICAL AREA TREAD PLATE OVERLAYS There shall be a tread plate overlay on the vertical areas of each side of the apparatus body. The overlay will be located in front of the body compartments.

REAR STEPS There shall be four (4) Cast Products bolt-on steps installed on the rear of the apparatus.

Each step shall have large open slots to prevent buildup of ice or mud and to provide a handhold when necessary. Steps shall be provided in the following locations:

• •

Three (3) bolt-on steps on the driver's side rear of the apparatus.

One (1) bolt-on steps on the officer's side rear of the apparatus.

The steps shall be adequately lit with LED lighting. There shall be one (1) light located above each set of steps on the rear face of the body, for a total of two (2) lights. Each light shall be located in a manner that shall light all of the steps on its respective side.

There shall be two (2) vertical handrails installed on the rear of the apparatus, one (1) on the driver's side and one (1) on the officer's side.

There shall be a horizontal handrail installed below the hose bed.

GROUND LADDER STORAGE The ground ladders shall be stored beneath the hose bed, to the officer's side of the water tank. The ladders shall be stored vertically on their beam in an aluminum rack with poly scuff strips. The ladders shall be accessible through a hinged tread plate door on the rear of the body.

The following ground ladders shall be supplied with the apparatus: One (1) Duo Safety, model 900-A, 24' two section aluminum extension ladder shall be provided. The ladder shall be constructed with 6061-T6 aluminum alloy and shall have a 750 pound duty rating. The ladder shall have a closed length of 14' 2.75".

One (1) Duo Safety, model 775-A, 14' aluminum roof ladder shall be provided. The ladder shall have a 750 pound duty rating and aluminum roof hooks that fold for storage.

One (1) Duo Safety, model 585-A, 10' folding ladder shall be provided. The ladder shall have a 300 pound duty rating and Duo Safety ladder shoes for slip resistance.

Quote No: 0015795 Page 28 of 62 October 27, 2015

PIKE POLE STORAGE Smeal Fire Apparatus Co.

There shall be two (2) aluminum tubes for the storage of pike poles installed in the ground ladder storage compartment.

The following pike poles shall be supplied with this location on the apparatus: One (1) Akron Brass, model UL-6, 6' fiberglass pike pole shall be provided. The light weight heavy duty pole shall be constructed of one and one quarter inch round fiberglass with a rubber bumper butt style handle.

One (1) Akron Brass, model UT-8, 8' fiberglass pike pole shall be provided. The light weight heavy duty pole shall be constructed of one and one quarter inch round fiberglass with a rubber bumper butt style handle.

HARD SUCTION HOSE STORAGE Provisions shall be made to provide storage for one (1) hard suction hose in the ladder storage compartment.

HARD SUCTION HOSE There shall be one (1) Firequip Maxi-Flex PVC 6” x 10’ section of hard suction hose provided.

HARD SUCTION HOSE STORAGE There shall be one (1) hard suction enclosed hose tray located inside the body, behind the driver's side header, with the capacity to store one (1) 10' section of hard suction hose. Access to the hard suction hose shall be from the rear of the apparatus through a hinged painted aluminum door.

HARD SUCTION HOSE There shall be one (1) Firequip Maxi-Flex PVC 6” x 10’ section of hard suction hose provided.

The wheel chocks shall be stored in locations that are easily accessible under the front of the body on the driver's side of the apparatus.

WHEEL CHOCKS There shall be one (1) pair of Cast Products model TMC1008-4 wheel chocks provided with the apparatus. The wheel chocks shall be mounted in Cast Products model TMC 1010 mounting brackets.

INDEPENDENT ALUMINUM SIDE MOUNT PUMP MODULE The pump module shall be a side mount design. The pump module shall be fabricated from 1/8" 5052-H32, smooth aluminum sheet. The module shall be fabricated as an individual unit, independent from the body. The module shall be fabricated utilizing the break and bend technique in order to form a strong, yet flexible, structure. The pump module shall be fabricated using precision holding fixtures to ensure proper dimensions and all attachment points shall be heavily reinforced.

Quote No: 0015795 Page 29 of 62 October 27, 2015

Smeal Fire Apparatus Co.

PUMP COMPARTMENT LIGHTS The pump compartment shall be equipped with two (2), 9" On-Scene Night Axe LED compartment lights. The lights shall be rated at 100,000 hours of service. The light shall be waterproof and magnesium chloride resistant. The light shall be enclosed in tough 5/8" Lexan tube. Multi-clip attachments shall allow for easy installation.

40,000 BTU PUMPCOMPARTMENT HEATER There shall be a 40,000 BTU marine grade heater installed in the pump compartment, in the most optimal position based on the application. The heater meets Coast Guard requirements for ignition protection and all hardware is marine grade.

The heater shall have an electric fan to circulate the heat throughout the pump compartment. The heating coil shall be connected to the engine cooling circuit with 5/8" heater hose and there shall be valves located in the engine compartment in order to turn off the flow to the heater in the event of hose failure.

There shall be a switch located on the pump operator's control panel to turn the heater fan on or off. An indicator light shall be illuminated when the fan is activated.

PUMP COMPARTMENT HEAT PAN There shall be a heat pan with a slide-in bottom panel installed beneath the pump compartment to contain the engine heat and prevent freezing of valves and plumbing in cold weather. The lower portion of the pump compartment area shall be enclosed on all sides, front, and rear. The slide-in panel shall be easily removable for warm weather operations.

The slide-in panel and housing shall be constructed out of aluminum.

DRIVER'S SIDE RUNNING BOARD A modular bolt-on running board shall be installed on the driver's side of the pump module. The running board shall be constructed of anti-slip tread plate. The outside edge of the running board shall be flush with the rub rail that is installed on the body to maintain a uniform appearance. The running board shall be installed with sufficient support to form a sturdy, non-deflecting step area for personnel.

OFFICER'S SIDE RUNNING BOARD A modular bolt-on running board shall be installed on the officer's side of the pump module. The running board shall be constructed of anti-slip tread plate. There shall be a floating storage well compartment recessed in the running board. The outside edge of the running board shall be flush with the rub rail that is installed on the body to maintain a uniform appearance. The running board shall be installed with sufficient support to form a sturdy, non-deflecting step area for personnel.

There shall be two (2) PAC, model 1008, straps provided with the storage well. The straps shall be installed over the top of the compartment.

The floor of the storage well shall be covered with Dri-Dek flooring.

Quote No: 0015795 Page 30 of 62 October 27, 2015

Smeal Fire Apparatus Co.

DUNNAGE COMPARTMENT There shall be a dunnage compartment located above the pump module. The dunnage compartment floor shall be constructed of tread plate.

FRONT PUMP ACCESS PANEL There shall be a painted aluminum access panel provided on the front of the pump compartment. The panel shall be of the single pan design and shall be secured utilizing stainless steel fasteners.

OFFICER'S SIDE PUMP ACCESS PANEL There shall be a tread plate door above the officer's side pump panel to allow access to the pump compartment. The vertically hinged panel shall be of the single pan design and shall be positively latched in the closed position utilizing a push button latch. A gas strut shall be provided on the door. An aluminum sill protector shall be installed on the bottom of the door opening to protect the paint from chipping and scratching. The door shall be wired into the door open warning light circuit.

CONTROL PANEL The driver's side of the pump enclosure shall be divided into two sections. The lower section shall be where all valve controls, the primer control, the discharge relief valve controls (pilot valve), and other mechanical controls are located. This surface shall be referred to as the "control panel".

All valve controls shall be the self-locking type, activated by either direct control or with a direct linkage utilizing friction locking bell cranks and universal ball swivels. The primary valve handles shall have color coded tags installed in a recessed area to clearly denote the purpose of each control.

INSTRUMENT PANEL The surface above the control panel shall contain all instruments, gauges, test fittings, and optional controls. This surface shall be referred to as the "instrument panel". The instrument panel shall be independent and hinged and latched so that it may be opened.

All instruments, gauges, and other equipment shall be installed with sufficient slack in any cabling, tubing, or plumbing to allow the panel to swivel to the fully open position.

The instrument and gauge panel shall be vertically hinged "swing out" to provide access for service.

OFFICER'S SIDE PUMP PANEL A single panel shall be installed on the officer's side of the pump enclosure. This shall be the area where any officer's side discharges, inlets, steamers, and other pump associated equipment are located. This panel shall be easily removable and held in place with quick release push latches. It shall be fully removable for pump and plumbing access without the need to use hand tools. Any electrical equipment that may be installed shall be equipped with connectors so they may be easily separated from the opening created when the below described front access panel is removed.

PANEL SURFACES Quote No: 0015795 Page 31 of 62 October 27, 2015

Smeal Fire Apparatus Co.

The control panel, instrument panel, and officer's side pump panel shall be coated with black Line-X® for maximum resistance to abrasion and to minimize glare. The material shall be capable of withstanding the effects of extreme temperatures and weather.

GARNISH RING BEZEL ASSEMBLIES Innovative Controls intake and/or discharge garnish rings shall be installed to the apparatus with mounting bolts. These bezel assemblies shall be used to identify intake and/or discharge ports with color and verbiage. The garnish rings shall be designed and manufactured to withstand the specified apparatus service environment and shall be backed by a warranty equal to that of the exterior paint and finish. The specified assemblies shall feature a chrome-plated panel-mount bezel with durable UV resistant polycarbonate inserts. These UV resistant polycarbonate graphic inserts shall be sub surface screen printed to eliminate the possibility of wear and protect the inks from fading. All insert labels shall be backed with 3M permanent adhesive (200MP), which meets UL969 and NFPA standards.

VERBIAGE TAG BEZEL ASSEMBLIES Innovative Controls verbiage tag bezels shall be installed. The bezel assemblies will be used to identify apparatus components. These tags shall be designed and manufactured to withstand the specified apparatus service environment and shall be backed by a warranty equal to that of the exterior paint and finish. The verbiage tag bezel assemblies shall include a chrome-plated panel-mount bezel with durable easy-to-read UV resistant polycarbonate inserts featuring the specified verbiage and color coding. These UV resistant polycarbonate verbiage and color inserts shall be sub-surface screen printed to eliminate the possibility of wear and protect the inks from fading. Both the insert labels and bezel shall be backed with 3M permanent adhesive (200MP), which meets UL969 and NFPA standards.

SAFETY MESSAGE BEZEL ASSEMBLIES Innovative Controls safety message bezels shall be installed. The bezel assemblies will be used to identify, instruct, or warn the operators. These tags shall be designed and manufactured to withstand the specified apparatus service environment and shall be backed by a warranty equal to that of the exterior paint and finish. The safety message bezel assemblies shall include a chrome-plated panel-mount bezel with durable easy-to read UV resistant polycarbonate inserts featuring ANSI safety standard graphics or custom graphics. These UV resistant polycarbonate graphic inserts shall be sub-surface screen printed to eliminate the possibility of wear and protect the inks from fading. Both the graphic insert labels and bezel shall be backed with 3M permanent adhesive (200MP), which meets UL969 and NFPA standards.

PUMP PANEL LIGHTING The pump operator's control panel and the officer's side pump panel shall each be illuminated by On-Scene LED Night Axe lighting. The pump panel lights shall become energized upon setting the parking brake so the gauge information provided may be consulted at any time the apparatus is parked. A stainless steel shield shall be installed over the pump panel lights to further protect them from the elements and to act as a reflector for additional illumination.

The pump panel lighting shall become energized automatically upon setting the park brake so the gauge information may be consulted at any time the apparatus is parked.

Quote No: 0015795 Page 32 of 62 October 27, 2015

Smeal Fire Apparatus Co.

MIDSHIP MOUNT FIRE PUMP The pump shall be a Waterous CSUC20 1500 U.S. GPM (6000 LPM) fire pump. The pump shall be a single stage centrifugal class "A" rated fire pump, designed specifically for the fire service.

The pump body shall be cast as two (2) horizontally split pieces. The body shall be made of high tensile, close-grained gray iron with a minimum tensile strength of 40,000 PSI.

FLAME PLATED IMPELLER HUBS The pump impellers shall be bronze, specifically designed for the fire service and accurately balanced for vibration free running. The stripping edges shall be located on opposite sides of the impellers to reduce shaft deflection.

The impeller shaft shall be stainless steel, accurately ground to size and supported at each end by oil or grease lubricated anti-friction ball bearings for rigid, precise support.

The bearings used on the impeller shaft shall be automotive type bearings, easily cross referenced and readily available at normal parts or bearing stores.

The impeller hubs shall be flame plated with tungsten carbide to hardness approximately twice that of tool steel to assure maximum pump life and efficiency. During the flame plating process the base metal shall not be allowed to exceed a temperature of 300 degrees Fahrenheit to prevent altering the metallurgical properties of the impeller material.

IMPELLER WEAR RINGS The pump shall be equipped with replaceable bronze wear rings for increased pump life and minimum maintenance cost. The wear rings shall be designed to fit into a groove in the face of the impeller hubs forming a labyrinth that, as the clearance increases with age, directs water from the discharge side in several directions eventually exiting outward, away from the eye of the impeller hub.

LUBRICATION SYSTEM An internal lubrication system shall deliver lubricant directly to the drive chain. This unique design shall eliminate the need for an external lubrication pump and auxiliary cooling. Oil shall be supplied with the lubrication system.

PUMP TRANSMISSION The pump shall have a Waterous model C20 series transmission. The housing of the transmission shall be constructed of high strength, three piece, horizontally split aluminum. The drive line shafts shall be made from alloy steel forgings, hardened and ground to a size 2.350 inch 46 tooth involute spline. The drive and driven sprockets shall be made of steel and shall be hardened and have ground bores. The drive chain shall be a Morse HV™ high strength involute form chain. Bearings shall be deep groove, anti friction ball bearings and shall give support and proper alignment to the impeller shaft assembly. Bearings shall be oil splash lubricated, completely separated from the water being pumped, and protected by a V-ring and oil seal. An internal lubrication system shall deliver lubricant directly to the drive chain. This unique design eliminates the need for an external lubrication pump and auxiliary cooling. The pump and transmission shall be Quote No: 0015795 Page 33 of 62 October 27, 2015

Smeal Fire Apparatus Co.

easily separable. A two-piece shaft shall be splined allowing for individual repair of either the pump or transmission, to keep down time to a minimum. All drive line components shall have a torque rating equal to or greater than the final net engine torque.

MECHANICAL SEALS The pump shall be equipped with self-adjusting, maintenance free mechanical shaft seals that shall not require manual adjustment. These seals shall be designed in a manner such that they shall remain functional enough to permit continued use of the pump in the unlikely event of a seal failure.

ZINC ANODES

• •

There shall be four (4) Waterous zinc anodes provided with the fire pump. The anodes shall aid in preventing galvanic corrosion within the water pump and be easily replaceable. The anodes shall be installed as follows: Two (2) on the intake side of the pump Two (2) in the discharge manifold of the fire pump.

The pump shall be rated at 1500 gallons per minute.

FIRE PUMP MOUNTING The fire pump shall be mounted within a separate body module that is not directly connected to the apparatus body.

The pump shall be frame mounted; therefore minimizing the likelihood of the pump casing cracking should the apparatus be involved in a collision.

The pump module shall be mounted to the frame in four (4) locations and shall be reinforced appropriately in order to carry the expected load for the life of the apparatus.

PUMP SHIFT The pump shift actuating mechanism shall be air operated from a valve in the cab identified as "PUMP SHIFT". Full instructions for shifting the pump shall be inscribed on the valve plate.

There shall be two (2) green pump system shift indicator lights in the chassis cab. The first light shall become energized when the pump has completed its shift into pump gear and shall be labeled "Pump Engaged". The second light shall become energized when the chassis parking brake has been set and when the pump and the chassis transmissions have been shifted completely into the correct gears for pumping, this light shall be labeled "OK to Pump".

There shall be one (1) green pump system shift indicator light located on the operator's panel. This light shall only become engaged when the chassis parking brake has been set and when the pump and the chassis transmissions have been completely shifted into the correct gears. The light shall be located adjacent to the throttle control and shall be labeled "Warning: Do Not Open Throttle Unless Light Is On".

PRESSURE GOVERNOR There shall be a Fire Research Pump Boss 400 pressure governor and monitoring Quote No: 0015795 Page 34 of 62 October 27, 2015

Smeal Fire Apparatus Co.

display kit installed. The kit shall include a control module, intake pressure sensor, discharge pressure sensor, and cables. The control module case shall be waterproof and have dimensions not to exceed 6 3/4" high by 4 5/8" wide by 1 1/2" deep. The control knob shall be 2" in diameter with no mechanical stops, have a serrated grip, and a red idle push button in the center. It shall not extend more than 1 3/4" from the front of the control module. Inputs for monitored information shall be from a J1939 data bus or independent sensors. Outputs for engine control shall be on the J1939 data bus or engine specific wiring. Inputs to the control module from the pump discharge and intake pressure sensors shall be electrical.

The following continuous displays shall be provided:

• • • • • • • • •

Engine RPM; shown with four daylight bright LED digits more than 1/2" high Check engine and stop engine warning LEDs Oil pressure; shown on a dual color (green/red) LED bar graph display Engine coolant temperature; shown on a dual color (green/red) LED bar graph display Transmission Temperature: shown on a dual color (green/red) LED bar graph display Battery voltage; shown on a dual color (green/red) LED bar graph display Pressure and RPM operating mode LEDs Pressure / RPM setting; shown on a dot matrix message display Throttle ready LED The dot-matrix message display shall show diagnostic and warning messages as they occur. It shall show monitored apparatus information, stored data, and program options when selected by the operator. All LED intensity shall be automatically adjusted for day and night time operation.

The program shall store the accumulated operating hours for the pump and engine to be displayed with the push of a button. The kit shall monitor inputs and support audible and visual warning alarms for the following conditions:

• • • • • • • •

High Battery Voltage Low Battery Voltage (Engine Off) Low Battery Voltage (Engine Running) High Transmission Temperature Low Engine Oil Pressure High Engine Coolant Temperature Out of Water (visual alarm only) No Engine Response (visual alarm only) The program features shall be accessed via push buttons located on the front of the control module. There shall be a USB port located at the rear of the control module to upload future firmware enhancements.

The governor shall operate in two control modes, pressure and RPM. No discharge pressure or engine RPM variation shall occur when switching between modes. A throttle ready LED shall light when the interlock signal is recognized. The governor shall start in pressure mode and set the engine RPM to idle. In pressure mode the governor shall automatically regulate the discharge pressure at the level set by the operator. In RPM mode the governor shall maintain the engine RPM at the level set by the operator except in the event of a discharge pressure increase. The governor shall limit a discharge pressure increase in RPM mode to a maximum of 30 psi. Other safety features shall include recognition of no water conditions with an automatic programmed response and a push button to return the engine to idle.

Quote No: 0015795 Page 35 of 62 October 27, 2015

Smeal Fire Apparatus Co.

An interlock system shall be provided to prevent advancement of the engine speed at the pump operator’s panel unless the apparatus has “Throttle Ready” indication.

The pressure governor and monitoring pressure display shall be programmed to interface with a specific engine.

INTAKE RELIEF VALVE There shall be an Elkhart Brass intake relief valve installed on the suction side of the pump. The valve shall be the preset type, adjustable from 75 to 250 PSI, and shall be designed to prevent vibration from altering the setting. The relief outlet shall be directed below the pump with the discharge terminating in a 2-1/2" male NST connection. The discharge shall be away from the pump operator and labeled "Do Not Cap".

TRIDENT PRIMING PUMP The priming pump shall be a Trident Emergency Products, model 31.001.7 three barrel, compressed air powered, high efficiency, multi-stage, venturi based AirPrime™ System.

All wetted metallic parts of the priming system are to be of brass and stainless steel construction. There shall be a pressure protection valve installed with the priming pump.

A single panel mounted control shall activate the priming pump and open the priming valve to the pump.

MASTER DRAIN VALVE A Trident manifold drain valve assembly shall be supplied. This drain shall provide the capability to drain the entire pump by turning a single control. The valve assembly shall consist of a stainless steel plate and shaft in a bronze body with multiple ports. The drain valve control shall be mounted on the driver's side pump panel and labeled "Master Drain".

WATEROUS OVERHEAT PROTECTION MANAGER WITH INDICATOR LIGHTS There shall be a Waterous Overheat Protection Manager (OPM), installed on the pump.

The relief valve shall automatically relieve water from the pump when the temperature of the pump water exceeds 140°F. In addition, a warning light on the pump panel shall be triggered by a thermal switch when the water in the pump reaches 180°F. The warning light acts as an additional protection device if the temperature inside the pump keeps rising although the valve is open. The valve shall automatically reset after activation.

PUMP PRIMED BLACK BY PUMP MANUFACTURER The pump shall be primed black by the pump manufacturer.

The steamers shall be unpainted and any inlets shall be the same color as they arrived from the valve manufacturer.

PUMP AND ENGINE COOLING SYSTEM There shall be a pump and engine cooling system provided on the apparatus. The cooling system shall keep the engine cool when running for long periods of time and the pump cool during long periods of pumping when water is not being discharged. The cooling system shall also be setup in a way that the cooling system lines can be easily drained through the master pump drain.

Quote No: 0015795 Page 36 of 62 October 27, 2015

Smeal Fire Apparatus Co.

The cooling system lines shall consist of high-pressure, high-temperature 3/8" (inside diameter) abraded rubber hose. The engine cooling lines shall be installed with one (1) line going from the discharge side of the water pump through an Innovative Controls, model 3004204-2-2, 3/8" in-line quarter turn ball valve assembly and continuing on to the chassis heat exchanger. The return line from the heat exchanger shall then run into the suction side of the pump. The pump cooling lines shall be installed with one (1) line going from the discharge side of the water pump through an Innovative Controls, model 3004204-2-2, 3/8" in-line quarter-turn ball valve assembly up to the water tank. At the water tank, the pump cooling line shall be plumbed into a 3/8" check valve on the "Tank Fill" valve. The check valve shall prevent tank water from back flowing into the pump when the cooling system is not in use. A return line from the water tank shall be plumbed into the water pump.

The engine cooling system valve shall be controlled on the operator's panel, and shall be clearly labeled, "Engine Cooler".

The pump cooling system valve shall be controlled on operators panel, and shall be clearly labeled, "Pump Cooler".

FOAM SYSTEM There shall be a FoamPro 2001 single foam system installed on the apparatus. The system shall be an electronic, fully automatic, variable speed, direct injection, and discharge side foam proportioning system. The system shall be capable of handling Class A foam concentrates and most Class B foam concentrates. The system shall be setup to utilize Class A foam. The foam proportioning operation shall be based on direct measurement of water flows, and remain consistent within the specified flows and pressures. The system shall be capable of delivering accuracy to within 3% of calibrated settings over the advertised operation range when installed according to factory standards. The system shall be equipped with a digital electronic control display, suitable for installation on the pump panel. Incorporated within the control display shall be a microprocessor that receives input from the system flow meter, while also monitoring foam concentrate pump output, comparing values to ensure that the operator preset proportional amount of foam concentrate is injected into the discharge side of the fire pump.

Paddlewheel type flow meter shall be installed in the discharges specified to be foam capable.

• • • • • • •

The digital computer control display shall enable the pump operator to perform the following control and operation functions for the foam proportioning system:

Provide push-button control of foam proportioning rates from 0.1% to 9.9% in 0.1% increments.

Show current flow-per-minute of water.

Show total volume of water discharged during and after foam operations are completed.

Show total amount of foam concentrate consumed.

Simulate flow rates for manual operation.

Perform setup and diagnostic functions for the computer control microprocessor.

Flash a "low concentrate" warning when the foam concentrate tank(s) run(s) low.

Flash a "no concentrate" warning and shut the foam concentrate pump off, preventing damage to the pump, should the foam tank(s) empty.

Quote No: 0015795 Page 37 of 62 October 27, 2015

Smeal Fire Apparatus Co.

A 12 volt electric motor driven positive displacement foam concentrate pump, rated up to 2.6 GPM (9.84 L/min), with operating pressures up to 400 PSI (27.6 BAR), shall be installed in a suitable compartment near the apparatus pump house. A pump motor electronic driver (mounted to the base of the pump) shall receive signals from the computer control display, and power the 1/2 horsepower electric motor. The electric motor is directly coupled to the concentrate pump in a variable speed duty cycle to ensure that the correct proportion of concentrate preset by the pump operator is injected into the water stream.

System capacity shall be as follows: Foam Concentrate Maximum / Water Flow GPM (L/Min)

• • • •

0.2% / 1300 (4921) 0.5% / 520 (1968) 1.0% / 260 (984) 3.0% / 85 (322) A full flow check valve shall be provided to prevent foam contamination of fire pump and water tank or water contamination of foam tank.

Components of the complete proportioning system as described above shall include:

• • • • • •

Operator control and display Paddlewheel flow meter Pump and electric motor/motor driven Wiring harnesses Low-level tank switch Foam injection check valve An installation and operation manual shall be provided for the unit, along with a one (1) year limited warranty. A system-schematic placard and a system-rating placard shall be supplied and installed in accordance with NFPA standards.

FLUSH SYSTEM A single foam flush system shall be installed to provide a clean water flush of the foam concentrate pump preventing foam concentrates from mixing and possible jelling. Clean water from the booster tank shall be plumbed to a 1/4 turn valve located on the pump panel. The valve shall be capable of operating pressures to 500 psi.

FOAM PROPORTIONING SYSTEM TESTING The foam proportioning system shall be tested and certified after final installation as per NFPA 1901.

PLUMBING MANIFOLD The plumbing manifold shall consist of the inlet side manifold and the discharge side manifold. Galvanized Victaulic couplings shall be used wherever possible for ease of maintenance and superior corrosion protection.

The inlet side of the plumbing manifold shall utilize schedule 10, 304 grade stainless steel tubing and preformed elbows for inlets that are larger than 3”. Side auxiliary inlets that are 3” or smaller shall utilize schedule 40, 304 grade stainless steel threaded tubing and preformed elbows. The inlet manifold shall thread into the pump auxiliary inlet ports Quote No: 0015795 Page 38 of 62 October 27, 2015

Smeal Fire Apparatus Co.

and each inlet valve shall thread onto the inlet manifold.

The discharge side of the plumbing manifold shall utilize schedule 40, 304 grade stainless steel tubing and preformed elbows to ensure the quality of the manifold where welds are required. The discharge manifold shall connect to the pump discharge ports using ½” stainless steel flanges that shall be machined to seat an O-ring to ensure a leak proof seal. Each discharge shall derive from a port on the manifold assembly connected to a discharge valve with 1/2” 304 grade stainless steel flanges. Discharges that terminate in a location other than the pump module (i.e. rear discharges) that do not require welding shall utilize a combination of high pressure flex hose and schedule 10, 304 grade stainless steel tubing to allow flexibility between the body and the pump module.

There shall be a Trident Emergency Products 3/4" quarter turn drain valve included.

There shall be a chrome plated rectangular handle provided on the drain valve to facilitate use with a gloved hand. The drain valve shall be located just above the running board and below the pump panel to reduce clutter in the pump panel area. The drain valve shall be connected to the valve with flexible hose that is routed in such a manner as to assure complete drainage to below the apparatus. A matching color coded bezel shall be included.

INNOVATIVE CONTROLS DISCHARGE GAUGES - 2-1/2" - 0-400PSI The discharge gauges on the apparatus shall be 2 ½” (63mm) diameter Innovative Controls pressure gauges. The gauges shall have a one-piece die-cast brass case that integrates the valve stem connection, movement support, and bourdon tube support into a single unit that eliminates distortion and leakage. Clear scratch resistant molded lenses shall be used to ensure distortion-free viewing and they shall be sealed to the gauge by being trapped together with a profile gasket by a crimped stainless steel bezel.

The gauges shall be filled with a synthetic mixture to dampen shock and vibration, lubricate the internal mechanisms, prevent lens condensation and ensure proper operation from –40°F to +160°F.

The gauges shall exceed ASME B40.100 Grade B requirements with an accuracy of +/ 1.5% full scale and include a size appropriate phosphorous bronze bourdon tube with a reinforced lap joint and large tube base to increase the tube life and gauge accuracy.

Highly-polished stainless steel bezels shall be provided to prevent corrosion and protect lenses and gauge cases. The gauges shall be installed into decorative chrome-plated mounting bezels that incorporate valve identifying verbiage and/or color labels.

The gauges shall display a range from 0 to 400 psi and shall have an orange tip on the pointer.

MASTER PRESSURE CENTER ASSEMBLY The master gauges shall be installed on the pump panel no more than 6 inches apart in an integrated master pressure assembly that includes the two (2) master gauges and the test port manifold.

The master intake and master discharge gauges shall be 4” (101mm) diameter Innovative Controls pressure gauges. Each gauge shall have a one-piece die-cast brass case that integrates the valve stem connection, movement support, and bourdon tube Quote No: 0015795 Page 39 of 62 October 27, 2015

Smeal Fire Apparatus Co.

support into a single unit that eliminates distortion and leakage. A clear scratch resistant molded lens shall be used to ensure distortion-free viewing and it shall be sealed to the gauge by being trapped together with a profile gasket by a crimped stainless steel bezel.

The gauge shall be filled with a synthetic mixture to dampen shock and vibration, lubricate the internal mechanisms, prevent lens condensation and ensure proper operation from –40°F to +160°F.

Each gauge shall exceed ASME B40.100 Grade B requirements with an accuracy of +/ 1% full scale and include a size appropriate phosphorous bronze bourdon tube with a reinforced lap joint and large tube base to increase the tube life and gauge accuracy. A highly-polished stainless steel bezel shall be provided to prevent corrosion and protect the lens and gauge case.

The two (2) master gauges shall be installed into a decorative chrome-plated zinc mounting bezel that also incorporates a test port manifold and a graphic overlay that identifies the master intake and discharge gauges, the vacuum test port, and the pressure test port. The test port manifold is solid cast brass with chrome-plated plugs.

The gauge on the left shall be the master pump intake gauge and display a range from -30 to 400 psi with black graphics on a white background. The gauge on the right shall be the master pump discharge gauge and display a range from 0 to 400 psi with burgundy graphics on a white background.

The non-Storz discharge and intake fittings provided on this apparatus shall be South Park Corp. Brand. The adapter/cap/plug fittings shall be manufactured from high quality brass that shall be polished to remove manufacturing irregularities with a chrome finish applied to the polished surface.

The Storz discharge and intake fittings provided on this apparatus shall be Task Force Tips Brand. For corrosion resistance, the adapter shall be constructed of hard coat anodized aluminum alloy and include a polymer bearing ring for prevention of galvanic corrosion.

The inlets shall terminate with NST swivels, and the discharges shall terminate with NST male threads.

DISCHARGE, PRE-CONNECT, AND INTAKE DRAINS There shall be a Innovative Controls 3/4" quarter turn drain valve included on each discharge, gated intake, and steamer valve (if applicable). There shall be a side stem, long stroke chrome plated lift handle provided on the drain valve to facilitate use with a gloved hand. The drain valve shall a verbiage tag that angles upward so that it can easily be seen and rear by the operator before opening. The drain valve shall be located just above the running board and below the pump panel to reduce clutter in the pump panel area. The drain valve shall be connected to the valve with flexible hose that is routed in such a manner as to assure complete drainage to below the apparatus. A matching color coded bezel shall be included.

2" TANK FILL There shall be a 2" tank fill plumbed from the pump to the tank. Installation shall be completed with 2" Class 1 rubber hose and stainless steel hose couplings.

An Akron Brass, model 8820, 2" Swing-Out™ valve shall be provided. The valve shall Quote No: 0015795 Page 40 of 62 October 27, 2015

Smeal Fire Apparatus Co.

have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a self-locking ball feature using an automatic friction lock design and specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1 manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

3" TANK-TO-PUMP There shall be a 3" tank-to-pump plumbed with a Class 1 flexible hose from the tank to the suction side of the pump. There shall be an Akron Brass, model 8830, 3" Swing Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a self-locking ball feature using an automatic friction lock design and specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall also include a necessary B3-SH pump flange adapter, which shall be specifically used for the tank-to-pump line to properly adjust the plumbing based on the pitch of the pump. The valve shall carry a ten (10) year warranty by the valve manufacturer.

There shall be a check valve between the pump suction and the booster tank valve. The check valve shall eliminate back flow into the water tank when the pump is connected to a pressurized source.

The valve shall be actuated by an Akron Brass, model R1 manual actuator. The manual actuator shall be controlled by an Innovative Controls push/pull T-handle.

The tank plumbing valves and controllers shall have the OEM Standard label package unless stated otherwise. The Pump-to-Tank Fill shall be labeled "TANK FILL" and shall have a Black label color. The Tank-To-Pump shall be labeled "TANK TO PUMP" and shall have a Navy Blue label color.

6" DRIVER SIDE STEAMER INLET There shall be a 6" steamer inlet located on the driver's side of the pump module. The suction fittings shall include a removable die-cast screen to provide cathodic protection for the pump thus reducing corrosion. A short steamer barrel shall be installed to accommodate an intake valve without exceeding the legal overall body width. The intake shall terminate MNST thread.

There shall be one (1) South Park, model LHC26P14AC, 6" NST long handle steamer cap provided.

2-1/2" DRIVER'S SIDE INLET There shall be a 2-1/2" gated inlet, with 2-1/2" plumbing, provided on the driver's side of Quote No: 0015795 Page 41 of 62 October 27, 2015

Smeal Fire Apparatus Co.

the pump module. The inlet shall be fully recessed behind the panel in order to keep the valve protected from the elements.

An Akron Brass, model 8825, 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model TSC manual actuator installed directly on the valve. The handle shall allow the valve to be controlled directly at the valve.

There shall be one (1) South Park, model HPC3008AC, 2 1/2" NST plug with chain provided.

6" OFFICER SIDE STEAMER INLET There shall be a 6" steamer inlet located on the officer's side of the pump module. The suction fittings shall include a removable die-cast screen to provide cathodic protection for the pump thus reducing corrosion. A short steamer barrel shall be installed to accommodate an intake valve without exceeding the legal overall body width. The intake shall terminate MNST thread.

There shall be a Neles Jamesbury, model 815W, butterfly valve provided. The valve shall be a 6" full flow valve with a 6" NST nipple. The valve shall be controlled by a hand wheel located on the pump panel, on the same side as the valve. The valve shall meet current NFPA standards for opening and closing speed.

There shall be an Innovative Controls, model 3004204-2-2, 3/8" in-line bleeder valve provided on the steamer inlet. The valve shall be used to bleed off air or water as per NFPA requirements.

There shall be an Elkhart Brass intake relief valve installed on the steamer valve. The valve shall be the preset type, adjustable from 75 to 250 PSI, and shall be designed to prevent vibration from altering the setting. The relief outlet shall be directed below the pump with the discharge terminating in a 2-1/2" male NST connection. The discharge shall be away from the pump operator and labeled "Do Not Cap".

There shall be one (1) Task Force Tips model #AH3HSP-NX 30 degree elbow provided.

The elbow shall be configured with a 4" swivel Storz coupling and a 6" female NH swivel rocker lug coupling.

There shall also be one (1) Task Force Tips model A01SP 4" Storz blind cap with lanyard provided.

All intakes shall have the OEM Standard label package unless stated otherwise. All intake labels shall be burgundy in color. Specific verbiage on each intake label tag shall be determined at the pre-construction meeting.

Quote No: 0015795 Page 42 of 62 October 27, 2015

Smeal Fire Apparatus Co.

2-1/2" DRIVER'S SIDE DISCHARGE There shall be a 2-1/2" discharge, with 2-1/2" plumbing, located on the driver's side of the pump compartment. The discharge shall terminate MNST.

An Akron Brass model 8625 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass rack and sector actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park, model SE393010AC, 2-1/2" Female NST swivel rocker lug x 2-1/2" Male NST 30º elbow adapter provided.

There shall be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

2-1/2" DRIVER'S SIDE DISCHARGE There shall be a 2-1/2" discharge, with 2-1/2" plumbing, located on the driver's side of the pump compartment. The discharge shall terminate MNST.

An Akron Brass model 8625 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass rack and sector actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park, model SE393010AC, 2-1/2" Female NST swivel rocker lug x 2-1/2" Male NST 30º elbow adapter provided.

There shall be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

Quote No: 0015795 Page 43 of 62 October 27, 2015

Smeal Fire Apparatus Co.

2-1/2" OFFICER'S SIDE DISCHARGE There shall be a 2-1/2" discharge, with 2-1/2" plumbing, located on the officer's side of the pump compartment. The discharge shall terminate MNST.

An Akron Brass, model 8825, 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park, model SE393010AC, 2-1/2" Female NST swivel rocker lug x 2-1/2" Male NST 30º elbow adapter provided.

There shall be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

4" OFFICER'S SIDE DISCHARGE There shall be a 4" large diameter discharge, with 4" plumbing, located on the officer's side of the pump compartment. The discharge shall terminate MNST.

An Akron Brass, model 8830, 3" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The actuator shall include an Akron Brass, model 7875, Slo-Cloz™ to control the opening and closing speed of the valve to minimize the effects of water hammer.

The valve actuator shall be controlled by an Elkhart Brass, model RC-10, handwheel valve controller. The 5" cast aluminum handwheel shall be connected to the remote mounted valve. The actuator housing and push-rod shall be constructed of light weight extruded aluminum. A precision needle thrust bearing and hardened thrust washers shall assure smooth, efficient operation and accurate flow and pressure control capability.

Opening and closing speed shall comply with the current NFPA standard to minimize effects of water hammer.

A valve position indicator shall show the position of the ball valve as per NFPA 1901. The Quote No: 0015795 Page 44 of 62 October 27, 2015

Smeal Fire Apparatus Co.

valve position indicator shall provide the pump operator with the status of the valve at a glance. Red shall mean fully closed; Green shall mean fully opened; Yellow shall indicate a gated position. LED lamps shall provide a reliable signal with a wide viewing angle even in bright sun light. Reliable solid state valve position sensors shall be water and lubricant resistant. The integrated circuit board and lamp sockets shall be completely encased in epoxy for total protection from the elements.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) Task Force Tips, model #AH3SP-NP 30 degree elbow provided.

The elbow shall be configured with a 4" swivel Storz coupling and a 4" female NH swivel rocker lug coupling.

There shall also be one (1) Task Force Tips, model #AA2SP-NJ adapter provided. The adapter shall be configured with a 4" rigid Storz coupling and a 2-1/2" male NH rigid.

There shall also be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

2-1/2" FRONT BUMPER DISCHARGE There shall be a 2-1/2" discharge located above the gravel shield on the officer's side of the front bumper. The discharge shall be plumbed with 2-1/2" plumbing and high pressure flex hose with stainless steel couplings. The discharge shall terminate MNST.

The discharge shall have Class1 model 34AD automatic drains installed in the low routed areas below the manual drain. The automatic drains shall open whenever pressure in the line drops below 6 psi.

The discharge shall be foam capable.

An Akron Brass, model 8825, 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park model A3720-AC, 2-1/2" Female NST rocker lug x 1-1/2" Male NST rigid reducer provided. The reducer shall be manufactured from high quality brass that shall be polished to remove manufacturing irregularities with a chrome finish applied to the polished surface.

Quote No: 0015795 Page 45 of 62 October 27, 2015

Smeal Fire Apparatus Co.

2-1/2" DRIVER'S SIDE REAR DISCHARGE There shall be a 2-1/2" discharge, with 2-1/2" plumbing, located on the driver's side rear of the apparatus. The discharge shall terminate MNST.

An Akron Brass, model 8825, 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park, model SE393010AC, 2-1/2" Female NST swivel rocker lug x 2-1/2" Male NST 30º elbow adapter provided.

There shall be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

2-1/2" OFFICER'S SIDE REAR DISCHARGE There shall be a 2-1/2" discharge, with 2-1/2" plumbing, located on the officer's side rear of the apparatus. The discharge shall terminate MNST.

An Akron Brass, model 8825, 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

There shall be one (1) South Park, model SE393010AC, 2-1/2" Female NST swivel rocker lug x 2-1/2" Male NST 30º elbow adapter provided.

There shall be one (1) South Park, model HCC2808AC, 2-1/2" NST vented rocker lug cap with chain provided.

Quote No: 0015795 Page 46 of 62 October 27, 2015

Smeal Fire Apparatus Co.

CROSSLAY CONFIGURATION There shall be two (2) 1-1/2" and one (1) 2-1/2" crosslay pre-connects located above the pump panel. Class1 high-pressure flex hose with stainless steel couplings shall be used in the plumbing.

A Trident 90º swivel elbow shall be utilized to keep the hose from kinking when pulled from either side of the apparatus. The swivel for each crosslay shall be located outboard for ease of making connections while changing hose.

The pre-connect hose beds shall be sized to accommodate the following hose load: The interior of the pre-connect hose bed shall have a maintenance free abraded finish.

The floor of the preconnect area shall be covered with Dura-Dek fiber reinforced material. The Dura-Dek shall have "T" beams in parallel connected with cross slats that are first mechanically bonded and then epoxied. The "T" sections shall be spaced 3/4" apart to allow for drainage and ventilation.

Stainless steel rollers shall be provided at each end of the crosslay hose bed to facilitate deployment of hose. Vertical rollers shall be installed on each side of the hose bed opening, and a horizontal roller shall be installed under the opening.

There shall be two (2) dividers in the crosslay area. Each divider shall be fabricated of 3/16" aluminum and be mounted in a channel on each end for adjustability. The dividers shall be coated with Line-X®, a black thermo-plastic polyurethane coating. The coating shall be durable enough to withstand the abuse of flying hose couplings without chipping or cracking.

CROSSLAY COVER There shall be an aluminum non-slip tread plate cover installed on the crosslay hose bed. The cover shall not interfere with hose loading when in the open position. When in the open position, the cover shall remain open due to automatically engaging mechanisms that require no type of latch operation to engage or release. The cover shall be provided with one full length stainless steel piano style hinge that shall attach the cover to the body. The cover shall be light yet rigid. Opening of the cover may be performed by one person on one side of the apparatus and yet the cover shall be rigid enough to support weight without deformation.

There shall be a heavy duty 22 oz. hypalon vinyl coated nylon end flap/cover located on each end of the pre-connected crosslays. The top of the end covers shall be connected to the tread plate top cover through a C-Rail channel. The bottom of the cover shall be attached to the pump module utilizing hooks and bungee cord. The cover color shall be black.

1-1/2" PRECONNECT There shall be a 1-1/2" preconnect with 2" plumbing. The preconnect shall terminate out a swivel MNST.

The 1-1/2" crosslay pre-connect shall have a capacity of 200' of 1-3/4" double jacket fire hose stored in a single stack.

The discharge shall be foam capable.

Quote No: 0015795 Page 47 of 62 October 27, 2015

Smeal Fire Apparatus Co.

An Akron Brass, model 8820, 2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

The discharge shall be designated as a pre-connect and no cap and chain shall be supplied.

1-1/2" PRECONNECT There shall be a 1-1/2" preconnect with 2" plumbing. The preconnect shall terminate out a swivel MNST.

The 1-1/2" crosslay pre-connect shall have a capacity of 200' of 1-3/4" double jacket fire hose stored in a single stack.

The discharge shall be foam capable.

An Akron Brass, model 8820, 2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

The discharge shall be designated as a pre-connect and no cap and chain shall be supplied.

2-1/2" PRECONNECT There shall be a 2-1/2" preconnect with 2-1/2" plumbing. The preconnect shall terminate out a swivel MNST.

The 2-1/2" crosslay pre-connect shall have a capacity of 200' of 2-1/2" double jacket fire hose stored in a single stack.

Quote No: 0015795 Page 48 of 62 October 27, 2015

Smeal Fire Apparatus Co.

The discharge shall be foam capable.

An Akron Brass, model 8825, 2-1/2" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats. The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The manual actuator shall be controlled by an Innovative Controls push/pull T handle.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

The discharge shall be designated as a pre-connect and no cap and chain shall be supplied.

3" DELUGE RISER DISCHARGE There shall be a 3" discharge for the deluge located above the pump module. The discharge shall be centered in the pump module and the riser shall terminate 3" NPT.

An Akron Brass, model 8830, 3" Swing-Out™ valve shall be provided. The valve shall have an all brass body with flow optimizing stainless steel ball and dual polymer seats.

The valve shall be capable of dual directional flow while incorporating a specially designed flow optimizing stainless steel ball. The valve shall not require lubrication of seats or any other internal waterway parts, and must be capable of swinging out of the waterway for maintenance by the removal of six bolts. The valve shall be manufactured and assembled in the United States. The valve shall carry a ten (10) year warranty by the valve manufacturer.

The valve shall be actuated by an Akron Brass, model R1, manual actuator installed on the valve. The actuator shall include an Akron Brass, model 7875, Slo-Cloz™ to control the opening and closing speed of the valve to minimize the effects of water hammer.

The valve actuator shall be controlled by an Elkhart Brass, model RC-10, handwheel valve controller. The 5" cast aluminum handwheel shall be connected to the remote mounted valve. The actuator housing and push-rod shall be constructed of light weight extruded aluminum. A precision needle thrust bearing and hardened thrust washers shall assure smooth, efficient operation and accurate flow and pressure control capability.

Opening and closing speed shall comply with the current NFPA standard to minimize effects of water hammer.

A valve position indicator shall show the position of the ball valve as per NFPA 1901. The valve position indicator shall provide the pump operator with the status of the valve at a glance. Red shall mean fully closed; Green shall mean fully opened; Yellow shall indicate a gated position. LED lamps shall provide a reliable signal with a wide viewing angle even in bright sun light. Reliable solid state valve position sensors shall be water and lubricant resistant. The integrated circuit board and lamp sockets shall be completely encased in epoxy for total protection from the elements.

Quote No: 0015795 Page 49 of 62 October 27, 2015

Smeal Fire Apparatus Co.

The discharge shall have a 2-1/2" brass case gauge with bezel and a display range from 0 to 400 psi. The gauge shall have a black dial graphic and an orange tip on the pointer.

ELKHART BRASS STINGER® MONITOR There shall be one (1) Elkhart Brass Stinger®, model 8297, manual monitor with a 3" NPT inlet provided on the apparatus. The monitor shall allow for 360 degrees of rotation and be able to move 90 degrees above and 15 degrees below the horizontal.

The monitor shall be complete with ST-194 stack tips and a 282A stream shaper.

The monitor shall be powder-coated Elkhart Red, RAL3003, by the monitor manufacturer and shall not be repainted by the OEM.

There shall be one (1) Elkhart Brass, model 283A, stream shaper provided.

There shall be one (1) set of Elkhart Brass, model ST-194, quad stacked tips provided.

All discharges shall have the OEM Standard label package unless stated otherwise.

Each discharge label shall be a unique color. Specific verbiage and colors on each discharge label tag shall be determined at the pre-construction meeting.

ELECTRICAL SYSTEM Wiring harnesses shall be the automotive type, engineered specifically for the builder's apparatus, and shall meet the following criteria. Under no circumstances shall diodes, resistors, or fusible links be located within the wiring harness. All such components shall be located in an easy to access wiring junction box or the main circuit breaker area. All wiring shall meet white book, baseline advanced design transit coach specification and Society of Automotive Engineers recommended practices. It shall be stranded copper wire core with cross linked polyethylene insulation complying with SAE specification J1128. Each wire shall be hot stamp function coded every three inches starting one inch from the end and continuing throughout the entire harness. In addition to function coding, each wire shall be number, color, and gauge coded.

Wire harnesses shall be wrapped with a high abrasion and chemical resistant thermoplastic polyester elastomer coated polyester yarn for braiding constructions of electrical wiring systems. The braid yarn shall have a minimum tensile strength of 15 lbs.

before breaking and have a maximum of 20% elongation before breaking. Temperature properties for the yarn shall range from a minimum 280°F (138°C) service temperature to a maximum -112°F (-80°C) brittleness temperature with a cold flex tolerance of at least -49°F (-45°C).

Harnesses shall be modular in design; a main harness system subdivided into several smaller sub-harnesses. The harness subsections shall be connected using Deutsch branded, heavy duty, environmentally sealed, connectors with silicone seals and a rear insertion/removal contact system. For isolation of electrical "zones" the harness subsections shall consist of a main harness, a pump harness with a separate pump gauge panel harness, a driver's side body harness with a separate driver's side compartment harness, a officer's side body harness with a separate officer's side compartment harness, and a rear body harness with two separate rear compartment harnesses.

The main harness and three body harnesses shall interconnect at a central, easy to Quote No: 0015795 Page 50 of 62 October 27, 2015

Smeal Fire Apparatus Co.

reach location and their connectors shall not be obstructed by other harnesses or fuel/air lines. In addition, the main and body harness connectors shall be color coded for ease of identification with their respective colors noted on the accompanying electrical diagrams.

Where connectors are not provided by the electrical component manufacturer, all 12 volt lights and other electrical components (excluding rocker and toggle switches) shall connect to the harnesses using Deutsch brand connectors; butt connectors are considered unacceptable.

All Deutsch connectors shall meet the following criteria:

• • • • •

All connectors shall have a minimum IP67 rating.

Temperature range from -67°F (-55°C) to 257°F (125°C) continuous at rated current.

Only solid contacts will be used. Stamped and formed contacts are unacceptable.

All contacts shall be soldered unless a crimping tool or machine is used that gives an even and precise pressure for the terminal being used.

All contacts shall be pull-tested to insure their integrity.

WEATHERPROOF DOOR SWITCHES Due the harsh environment and susceptibility to moisture on the fire ground, the fire apparatus compartment doors shall utilize weatherproof switches. Two different types of switches shall be used. Weatherproof proximity switches shall be utilized. No Exceptions.

The switches shall be used for activation of the compartment lights and to provide a signal to the door open circuit in the cab.

V-MUX ELECTRICAL MANAGEMENT SYSTEM The apparatus shall be equipped with a V-MUX Multiplex System. There are several key benefits to multiplexing, one is to reduce the number of connections in a vehicles electrical system, because of this it is important to limit the amount of modules that control certain functions of the vehicle.

Outputs: The outputs shall perform all the following items without added modules to perform any of the tasks: Quote No: 0015795 Page 51 of 62 October 27, 2015

Smeal Fire Apparatus Co.

Load Shedding: The System shall have the capability to Load Shed with 8 levels any output. This means you can specify which outputs (barring NFPA restrictions) you would like Load Shed. Level 1 12.9v, Level 2 12.5V, Level 3 - 12.1V, Level 4 - 11.7V, Level 5 11.3V, Level 6 10.9V, Level 7 10.5, Level 8 10.1. Unlike conventional load shedding devices you can assign a level to any or all outputs. No add-on modules shall be acceptable; the module with the outputs must perform this function.

Load Sequencing: The System shall be able to sequence from 0 8 levels any output.

With 0 being no delay and 1 being a 1 second delay, 2 being a 2 second delay and so on. Sequencing reduces the amount of voltage spikes and drops on your vehicle, and can help limit damage to your charging system. No add-on modules shall be acceptable; the module with the outputs must perform this function.

Output Device: The System shall have solid-state output devices. Each solid-state output shall be a MOS-FET (Metal Oxide Semiconductor - Field Effect Transistors); MOS-FETs are solid-state devices with no moving parts to wear out. A typical relay when loaded to spec has a life of 100,000 cycles. The life of a FET is more than 100 times that of a relay. No add-on modules shall be acceptable; the module with the outputs must perform this function.

Flashing Outputs: The System shall be able to flash any output in either A or B phase, and logic is used to shut down needed outputs in park, or any one of several combined interlocks. The flash rate can be selected at either 80, or 160 FPM. This means any light can be specified with a multiplex truck with no need to add flashers.

Flashing outputs can also be used to warn of problems. No add-on modules shall be acceptable; the module with the outputs must perform this function.

PWM: The modules shall have the ability to PWM at some outputs so that a Headlight PWM module is not needed. No add-on modules shall be acceptable; the module with the outputs must perform this function.

Diagnostics: An output shall be able to detect either a short or open circuit.

Inputs: The inputs shall have the ability to switch by a ground or battery signal.

The inputs shall be filtered for noise suppression via hardware and software so that RF or dirty power will not trick an input into changing its status.

System Network: The Multiplex system shall contain a Peer-to-Peer network. A Master Slave Type network is not suitable for the Fire/Rescue industry. A Peer-to-Peer network means that all the modules are equal on the network; a Master is not needed to tell other nodes when to talk.

System Reliability: The Multiplex system shall be able to perform in extreme temperature conditions, from -40° to +85° C (-40° to +185° F.) The system shall be sealed against the environment, moisture, humidity, salt or fluids such as diesel fuel, motor oil or brake fluid. The enclosures shall be rugged to withstand being mounted in various locations or compartments around the vehicle. The modules shall be protected from over voltage and reverse polarity.

12 VOLT SYSTEMS TEST After completion of the unit, the 12 volt electrical system shall undergo a battery of tests Quote No: 0015795 Page 52 of 62 October 27, 2015

Smeal Fire Apparatus Co.

as listed in NFPA 1901. These tests shall include, but not be limited to:

• • • •

Reserve capacity test Alternator performance test at idle Alternator performance test at full load Low voltage alarm test Certification of the results shall be supplied with the apparatus at the time of delivery.

TAIL LIGHTS There shall be a Whelen 600 series LED tail light assembly installed on each side of the rear of the apparatus. Each assembly shall include one (1) red LED stop/tail combination light model number 60BTT, one (1) amber LED model 60A00TAR turn light with arrow and one (1) clear LED backup light model 60C00WCR. The lights shall be mounted in a chrome plated four (4) light composite housing. The remaining slot in the housing shall be filled with a warning light specified in the warning light section.

REAR WORK LIGHT WIRING The backup lights shall be wired to the rear work light switch. This switching circuit shall be deactivated when the parking brake is released. The lights shall also be activated when the transmission if placed in reverse.

CAB SWITCH There shall also be a rocker switch provided in the cab to activate the backup lights. This switching circuit shall be deactivated when the parking brake is released. The lights shall also be activated when the transmission if placed in reverse.

MIDSHIP TURN SIGNALS There shall be two (2) Truck-Lite model 21 LED midship auxiliary/turn signal lights installed. One (1) light shall be located in the rub rail on each side of the body.

BODY GROUND LIGHTING There shall be Truck-Lite, model 44, 4" round LED lights shall be installed beneath the apparatus in areas where personnel may be expected to climb on and off of the apparatus. The lights shall illuminate the ground within 30" of the apparatus to provide visibility of any obstructions or hazards. These areas shall include, but shall not be limited to, side running boards and the rear step area.

The lights shall be activated when the parking brake is engaged.

CLEARANCE LIGHTS Grote model 65282 red LED clearance lights shall be installed in the rear tailboard as necessary to be in full compliance with applicable ICC and DOT codes and regulations.

Clearance reflectors shall be placed on the apparatus to be in full compliance with applicable ICC and DOT codes and regulations.

UPPER ZONE A There shall be one (1) Whelen Engineering Freedom, model FN60QLED, 60" LED lightbar installed on the chassis cab roof. The lightbar shall be equipped with four (4) Quote No: 0015795 Page 53 of 62 October 27, 2015

Smeal Fire Apparatus Co.

forward facing linear red LED, two (2) forward facing linear white LED, two (2) corner forward facing red LED, and two (2) side facing red LED lights.

The lightbar shall be equipped with clear lenses. All clear LED lights in the lightbar shall be deactivated in the Blocking Right of Way mode.

UPPER ZONE C There shall be two (2) Whelen L31 series Super-LED® beacons installed in Upper Zone C. The high profile 12v beacons shall incorporate thirty two (32) Super-LEDs installed in sets of eight (8) on four (4) PC boards. The four (4) PC boards will be installed on a LED ballast. The beacons shall have an optic hard coated polycarbonate lens, and a metalized reflector with clear optic collimators. The hard coated lens shall provide extended life/luster protection against UV and chemical stresses. The four (4) conformal coated PC boards shall provide additional protection against environmental elements.

The beacons shall include 28 Scan-Lock™ patterns including four (4) simulated rotating patterns and synchronized features. The beacons shall also contain cruise mode and low power mode. The beacon dome lenses shall be sealed to a black powder coated die cast aluminum base with an “O” ring gasket assembly. The solid state beacon light shall be vibration resistant.

The driver's and officer's side beacons shall both have red LED's and red lenses.

LOWER ZONE WARNING LIGHT PACKAGE There shall be four (4) Whelen 600 Series Super-LED® lights with chrome-plated flange installed in the lower zone of the apparatus to meet NFPA compliance. The hard coated lens shall provide extended life/luster protection against UV and chemical stresses. The conformal coated PC board and sealed lens/reflector assembly shall provide additional protection against environmental elements. The solid state warning lights shall be vibration resistant.

The lower zone warning lights shall all have red LED's and red lenses.

TRAFFIC ADVISOR™ There shall be one (1) Whelen model TAM65 LED Traffic Advisor™ installed on the apparatus. The traffic directional light shall contain six (6) high intensity LED lamps in a black low profile flat style housing.

There shall be a Whelen, model TACTLD1 traffic advisor control head provided with the Traffic Advisor™. The control head shall be housed in a rugged extruded aluminum case and shall offer eight programmable sequence flash patterns.

The traffic directional light shall be recess mounted in the rear of the body.

There shall be one (1) air horn button provided on the driver's side pump panel. The button shall be red in color and included a label reading "AIR HORN".

WHELEN 12V SURFACE-MOUNT SCENE LIGHTS There shall be two (2) Whelen 600 Series Super-LED®, model 6SC0ENZR, lights installed on the apparatus. Each steady burn scene light shall incorporate 12 clear Super-LEDs, a clear gradient optic hard coated polycarbonate lens, and utilize a TIR optic reflector for maximum output. The hard coated lens shall provide extended life/ Quote No: 0015795 Page 54 of 62 October 27, 2015

Smeal Fire Apparatus Co.

luster protection against UV and chemical stresses. Each light's conformal coated PC board and wet sealed then vacuum tested lens/reflector assembly shall provide additional protection against environmental elements. Each solid state scene light shall be vibration resistant. Each light is certified to meet KKK 1822K requirements and 024 Standards. An installation kit including mounting hardware and rubber gasket shall be provided for surface mounting. The scene lights are covered by a five year factory warranty.

The two (2) lights shall be installed on the rear face of the body, one (1) on each side.

The 12 volt rear scene light(s) shall be controlled by one (1) switch located in the chassis cab and one (1) switch located at the pump panel. Each switch shall have an indicator that shall illuminate when the switch is in the “ON” position. The light(s) shall be controlled by one (1) switch at each location. The switch shall be labeled "REAR SCENE." In addition to each switch located in the cab and at the pump panel, the 12 volt rear scene light(s) shall be activated by the rear work light switch and when the apparatus is placed in reverse.

GENERATOR There shall be a Cummins Onan, model 6RBAB, 6000 watt hydraulic driven generator set installed on the apparatus. The generator shall be rated at 6,000 watts, 50/25 amps at 120/240 volts. Current frequency shall be stable at 60 hertz. The generator shall include a variable displacement piston pump, gear motor drive, and digital control for minimal voltage and frequency variation.

Hydraulic details Cooling:

• •

High efficiency forward-inclined blade, plug fan

• •

Pressurized box with distribution volutes for optimum air velocity across heat exchanger Welded blades, 4 brace rods and epoxy powder coated for best fan durability Heat exchanger sized relative to kW Hydraulic power:

• • • • • •

Operating flow and pressure range 14 gal/min, 350-3000 psi Pump control is pressure compensated load sense system Solenoid PWM controls flow and closes fully when generator set is switched off Required pump speed 850-3200 r/min maximum Generator set requires 23.3 hp from drive engine at full load Generator set drive motor - fixed displacement gear Alternator details October 27, 2015 Quote No: 0015795 Page 55 of 62

Smeal Fire Apparatus Co.

• • • • • • •

Design: Cummins Onan AC, 2-pole self-excited revolving field, permanently aligned to hydraulic motor by a splined shaft Cooling: Direct drive blower wheel Rotor: Laminated electrical steel assembly press-fitted to shaft, balanced; heavy insulated, Class 200 copper wire windings, optimized air gap for improved wave form and motor starting Stator: Laminated electrical steel assembly, skewed for improved waveform; heavy insulated, Class 200 copper wire windings DC brushes: Electrographic; long life Bearing: Double-sealed pre-lubricated ball bearing Exciter: Power Scan® regulator and bridge rectifier supply field current through slip rings Fluid Dexron III or 10 wt. antiwear hydraulic oil ~5 Ga The power-generating unit shall be a modular unit contained in a silver powder coat steel housing with single side serviceability and shall include a four-point vibration isolated mounting system.

The generator set shall be factory tested for proper starting and operations at extreme temperatures from -20 degrees F to +120 degrees F. The generator shall be manufactured and designed in facilities certified to ISO 9001.

The Cummins Onan generator set shall carry a 5 year, 1000 hour limited warranty from Onan.

GENERATOR DISPLAY There shall be a LED generator display meter provided with the generator. The display meter shall automatically sense a generator signal and begin displaying information. The digital meter display shall constantly monitor and display voltage, frequency and amps.

The display shall be capable of displaying total accumulated run time hours when the MODE button is pressed once. Press the MODE button twice to display the temperature of the oil returning to the oil reservoir.

There shall be a remote start switch installed on the pump panel for the generator.

GENERATOR PTO CONNECTION The hydraulic pump for the generator shall be connected to the chassis transmission through a "Hot Shift", electrically engaged power-takeoff system. The control to engage and disengage the power-takeoff system shall be installed in the chassis cab.

The Onan generator shall be located above the pump module.

8 CIRCUIT NON-GFI LOAD CENTER There shall be a 120/240 volt load center incorporated into the 120/240 volt wiring system. The load center shall include adequate circuit breakers to protect the loads specified on the apparatus. The entire 120/240 volt electrical system shall be installed in strict compliance with NFPA 1901. This shall include all testing, labeling, wiring methodology, and dimensional requirements. Certification of compliance shall accompany the apparatus at the time of delivery. All 120/240 volt A.C. Wiring shall be done in accordance with NFPA 1901 as well as nationally accepted electrical codes.

BRANCH CIRCUIT OVERCURRENT PROTECTION Quote No: 0015795 Page 56 of 62 October 27, 2015

Smeal Fire Apparatus Co.

Over current protection devices shall be provided for circuits in accordance with NFPA 1901. The load center shall be equipped with a non-GFI two pole main breaker when the six or more individual branch circuits are present. Over current protection devices shall be marked with labels to identify the function of the circuit they protect.

The generator load center shall be located on the forward bulkhead of the L1 compartment.

ELECTRIC CORD REEL There shall be Akron Brass electric rewind cord reel installed on the apparatus. The cord reel shall be equipped with a universal frame that will allow the 12 volt motor to be mounted in four (4) different positions. All metal parts, except for the electric motor and sprocket teeth, shall be powder painted red. All hardware shall be stainless steel. The cord reel disks shall have rolled edges to prevent sharp edges. The cord reel shall include the solenoid, switch and circuit breaker. The reel shall be covered by an Akron Brass five (5) year warranty. Rollers shall be supplied to prevent damage to the electrical cable if pulled in any direction.

The cord reel shall be equipped with 150' of yellow STW Seoprene 10/3 wire installed with a cable stop to prevent damage to cable fittings.

JUNCTION BOX There shall be an Akron Brass Extenda-Lite, model EJBX, back lighted electrical junction box equipped with four (4) electrical receptacles, two (2) per side. Each receptacle shall be equipped with a spring loaded snap cover. The cord reel shall be hardwired to the cast aluminum junction box to supply power to the four (4) receptacles. An extension cord shall be connected to the junction box through a heavy-duty water resistant strain relief and flexible extender. Each side of the junction box shall be fitted with polypropylene faceplates, which are backlighted, so that plug orientation to the receptacles is quick and easy to align.

The junction box shall be equipped with an Akron Brass model CS cord stop.

The junction box shall have a yellow powder-coat finish.

There shall be one (1) NEMA 5-15R, 120 volt, duplex, 3-wire, straight blade (household type) receptacle installed on the junction box. The receptacle shall have a 15 ampere rating and include a spring-loaded weather resistant cover if mounted in an exterior location.

There shall be one (1) NEMA 5-15R, 120 volt, duplex, 3-wire, straight blade (household type) receptacle installed on the junction box. The receptacle shall have a 15 ampere rating and include a spring-loaded weather resistant cover if mounted in an exterior location.

There shall be one (1) NEMA 5-15R, 120 volt, duplex, 3-wire, straight blade (household type) receptacle installed on the junction box. The receptacle shall have a 15 ampere rating and include a spring-loaded weather resistant cover if mounted in an exterior location.

There shall be one (1) NEMA 5-15R, 120 volt, duplex, 3-wire, straight blade (household type) receptacle installed on the junction box. The receptacle shall have a 15 ampere Quote No: 0015795 Page 57 of 62 October 27, 2015

Smeal Fire Apparatus Co.

rating and include a spring-loaded weather resistant cover if mounted in an exterior location.

The cord reel shall be located in the dunnage compartment.

A tread plate mounting bracket to hold the junction box shall be included.

FIRE RESEARCH 120V TELESCOPING SCENE LIGHTS There shall be two (2) Fire Research Spectra LED series, model SPA530-K20, side mount push up telescopic lights installed on the apparatus. Each light pole shall be anodized aluminum and have a knurled twist lock mechanism to secure the extension pole in position. The extension poles shall rotate 360 degrees. The outer poles shall be a grooved aluminum extrusion and qualify as an NFPA compliant handrail. Each pole mounting brackets shall have a 2 3/4" offset. Wiring shall extend from the pole bottom with a 4' retractile cord.

Each lamphead shall have sixty (60) ultra-bright white LEDs, 48 for flood lighting and 12 to provide a spot light beam pattern. They shall operate at 120 volts AC, draw 2 amps, and generate 20,000 lumens of light. Each lamphead shall have a unique lens that directs flood lighting onto the work area and focuses the spot light beam into the distance. Each lamphead angle of elevation shall be adjustable at a pivot in the mounting arm and the position locked with a round knurled locking knob. Each lamphead shall be no more than 5 7/8" high by 14" wide by 3 1/2" deep and have a heat resistant handle. The lampheads and mounting arms shall be powder coated. The LED scene lights shall be for fire service use.

The lights shall be located on the rear of the chassis cab, one (1) on each side.

Each light shall be controlled with a circuit breaker in the load center.

CHASSIS PAINT The two-tone chassis cab shall be painted by the chassis manufacturer.

BODY PAINT PREPARATION After the body and components have been fabricated and assembled they then shall be disassembled prior to painting so when the apparatus is completed there shall be finish paint beneath the removable components. The apparatus body and components shall be metal finished as follows to provide a superior substrate for painting.

All aluminum sections of the body shall undergo a thorough cleaning process starting with a phosphoric acid solution to begin the etching process followed by a complete rinse. The next step shall consist of a chemical conversion coating applied to seal the metal substrate and become part of the aluminum surface for greater film adhesion.

After the cleaning process, the body and its components shall be primed with a High Solids primer and the seams be caulked.

All bright metal fittings, if unavailable in stainless steel or polished aluminum, shall be heavily chrome plated. Iron fittings shall be copper under plated prior to chrome plating.

PAINT PROCESS Quote No: 0015795 Page 58 of 62 October 27, 2015

Smeal Fire Apparatus Co.

The paint process shall follow the strict standards as set forth by PPG Fleet Finish Guidelines.

The body shall go through a three-stage paint process: primer coat, base coat (color), and clear coat. In the first stage of the paint process the body shall be coated with PPG F3980 Low VOC / High Solids primer to achieve a total thickness of 2-4 mills. In the second stage of the paint process the body shall be painted with PPG FBCH Delfleet™ High Solids Polyurethane Base Coat. A minimum of two to three coats of paint shall be applied to achieve hiding. In the final stage of the paint process the body shall be painted with PPG DCU-2002 Clear Coat. A minimum of two to three coats shall be applied to achieve a total dry film thickness of 2-3 mills.

As part of the curing process the painted body shall go through a Force Dry / Bake Cycle process. The painted components shall be baked at 185 degrees for 3 hours to achieve a complete coating cure on the finished product.

HAND POLISHED After the Force Dry / Bake Cycle and ample cool down time, the coated surface shall be sanded using 3M 1000, 1200, and or 1500 grit sandpaper to remove surface defects. In the final step, the surface shall be buffed with 3M super-duty compound to add extra shine to coated surface. No more than .5 mil of clear shall be removed in this process.

BODY COLOR The body shall be painted with PPG High Solids Polyurethane Base Coat. The single tone body shall be painted (RED) PPG# FBCH-71096-ALT.

UNDERCOATING The apparatus shall undergo a two (2) step undercoating process. The first step shall be a rubberized polyurethane base compound that is applied after the body has been primed. The materials used incorporate unused paint products to reduce the amount of waste released into the environment. This coat shall be applied to all hidden pockets and surfaces that shall not be visible after completion.

As a final step, the entire underside of the body shall be coated with a bituminous based automotive type undercoating when the apparatus is completed. During this application, special care shall be taken to avoid spraying the product on air lines, cables, or other items that would cause normal maintenance to be hindered.

CORROSION PREVENTION One (1) 3.75 ounce tube of Electrolysis Corrosion Kontrol (ECK) shall be provided to use whenever additional items are mounted to the apparatus.

ECK protects aluminum and stainless steel against electrolytic reaction, isolates dissimilar metals and gives bedding protection for hardware and fasteners. ECK contains anti-seizing lubricant for threads. ECK is dielectric and perfect for use with electrical connectors.

Quote No: 0015795 Page 59 of 62 October 27, 2015

Smeal Fire Apparatus Co.

TOUCH UP PAINT One (1) two ounce bottle of acrylic enamel touch-up paint or two (2) touch up paint pens, if color is available, shall be supplied.

3" GOLD LEAF LETTERING There shall be up to one hundred (100) 22KT gold leaf letters provided and installed on the apparatus. The letters shall be approximately 3" tall with black outline and shadow.

18" REFLECTIVE LETTERING There shall be up to four (4) reflective letters provided and installed on the apparatus.

The letters shall be approximately 18" tall.

REFLECTIVE STRIPE FRONT TERMINATION The NFPA reflective stripe located on the side of the apparatus shall wrap around the front of the chassis cab and terminate at chassis grill.

RUB RAIL REFLECTIVE STRIPING There shall be 2" reflective striping installed in the rub rail channel. The reflective striping shall be diamond grade quality material for increased visibility. The reflective shall be silver in color.

NFPA COMPLIANT REFLECTIVE STRIPING Reflective striping shall be applied to the exterior of the apparatus in a manner consistent with NFPA 1901. It shall consist of a straight, 4" wide stripe along the front of the chassis and along the sides, staying below the tops of the wheel well areas.

The color of the main reflective striping on the apparatus shall be white.

CHEVRON COLOR - RED/FLUORESCENT YELLOW-GREEN The chevron striping shall consist of 3M part numbers 1172 EC, red and 3983, fluorescent yellow-green.

Only 3M Diamond Grade™ VIP Reflective Striping shall be used. 3M Diamond Grade™ VIP Reflective Striping is a wide angle prismatic lens reflective sheeting designed for the production of durable traffic control signs and delineators that are exposed vertically in service. This sheeting is designed to provide higher sign brightness than sheetings that use glass bead lenses. It is intended to also provide high sign brightness in the legibility distance where other sheetings do not.

CHEVRON REFLECTIVE STRIPING ON REAR In addition to the custom striping pattern supplied on the apparatus, there shall be additional reflective striping applied to the entire rear of the unit. The reflective striping shall cover at least 50% of the rear facing vertical surface per NFPA 1901. The striping shall consist of a solid base layer of reflective material and alternate between the exposed base layer material and durable, transparent, acrylic colored film. Each stripe Quote No: 0015795 Page 60 of 62 October 27, 2015

Smeal Fire Apparatus Co.

shall be a minimum of 6" in width and shall be applied to the apparatus at 45° angle.

The chevron pattern shall include any painted storage compartment doors.

FIVE (5) YEAR PARTS AND LABOR WARRANTY OEM installed purchased parts and fabricated parts shall be free of defects in material and workmanship for a period of five (5) years starting thirty (30) days after the original invoice date. For further details, please refer to the complete warranty document.

TEN (10) YEAR WARRANTY BODY STRUCTURAL INTEGRITY The body shall be free of structural or design failure or workmanship for a period of ten (10) years or 100,000 miles starting thirty (30) days after the original invoice date.

FIVE (5) YEAR 100% V-MUX ELECTRICAL WARRANTY The V-mux electrical system shall be free of defects in design and workmanship for a period of five (5) years starting thirty (30) days after the original invoice date. For further details, please refer to the complete warranty document.

TEN (10) YEAR STAINLESS STEEL PLUMBING LIMITED WARRANTY The stainless steel plumbing and piping shall be free from corrosion perforation for a period of ten (10) years starting thirty (30) days after the original invoice date.

WATER TANK WARRANTY The tank shall be complete with a lifetime warranty. The tank manufacturer shall mark the tank and furnish notice that indicates proof of warranty. For further details, please refer to the complete warranty document.

TWENTY (20) YEAR GALVANIZED SUB-FRAME WARRANTY The galvanized sub-frame shall be free of structural or design failure or workmanship for a period of twenty (20) years starting thirty (30) days after the original invoice date. For further details, please refer to the complete warranty document.

Quote No: 0015795 Page 61 of 62 October 27, 2015

Smeal Fire Apparatus Co.

TEN (10) YEAR PAINT LIMITED WARRANTY The apparatus body and pump house shall be free of blistering, peeling and any other adhesion defect caused by defective manufacturing methods or paint material selection for exterior surfaces for a prorated period of ten (10) years starting thirty (30) days after the original invoice date.

Paint on the undercarriage, body interior (Line-X® coating included) or aerial structure related paint, if applicable, is covered only under the Standard One (1) Year Limited Warranty.

TEN (10) YEAR CORROSION LIMITED WARRANTY The body exterior paint shall be warranted against corrosion perforation for a prorated period of ten (10) years starting thirty (30) days after the original invoice date. For further details, please refer to the complete warranty document.

PUMP WARRANTY The fire pump shall be warranted by Waterous for a period of five (5) years from the date of delivery to the fire department or five and one-half (5-1/2) years from the shipment date by Waterous, whichever period shall be first to expire. For further details, please refer to the complete warranty document.

PUMP WARRANTY The fire pump shall be warranted by Waterous for a period of five (5) years from the date of delivery to the fire department or five and one-half (5-1/2) years from the shipment date by Waterous, whichever period shall be first to expire. For further details, please refer to the complete warranty document.

Quote No: 0015795 Page 62 of 62 October 27, 2015

Smeal Mid Chassis Description without Price

VEHICLE

MODEL

0100-011 8012-002 8011-017 8001-001 8006-009 8008-001 0104-001 0101-003 0102-004 8010-002

CUSTOMERS / OEMS MODEL YEAR COUNTRY OF SERVICE APPARATUS TYPE VEHICLE TYPE AXLE CONFIGURATION GROSS AXLE WEIGHT RATINGS FRONT GROSS AXLE WEIGHT RATINGS REAR PUMP PROVISION

CAB

1000-013 8101-103 1501-009 1518-024 1551-002 1552-002 1521-002 1533-001 1522-001 1523-002 1524-004 1515-005 8013-036 1334-036 1005-001 1101-001 1322-002 8004-023 9001-006

CAB STYLE OCCUPANT PROTECTION CAB FRONT FASCIA FRONT GRILLE CAB UNDERCOAT CAB SIDE DRIP RAIL CAB PAINT EXTERIOR CAB PAINT MANUFACTURER CAB PAINT PRIMARY/LOWER COLOR CAB PAINT SECONDARY/UPPER COLOR CAB PAINT EXTERIOR BREAKLINE CAB PAINT PINSTRIPE CAB PAINT WARRANTY CAB PAINT INTERIOR CAB ENTRY DOORS CAB ENTRY DOOR TYPE CAB INSULATION CAB STRUCTURAL WARRANTY CAB TEST INFORMATION

ELECTRICAL POWER DISTRIBUTION

5000-001

ELECTRICAL SYSTEM

5622-010 5031-005 5011-001

DATA RECORDING SYSTEM ACCESSORY POWER EXTERIOR ELECTRICAL TERMINAL COATING

Qty. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

ENGINE

1701-144 1329-001 1731-002 1718-002 1719-002 1710-001 1713-005 1708-002 1720-003 1715-001 1735-001 8002-001 1707-016 1721-001 1727-001

ENGINE CAB ENGINE TUNNEL DIESEL PARTICULATE FILTER CONTROLS ENGINE PROGRAMMING HIGH IDLE SPEED ENGINE HIGH IDLE CONTROL ENGINE PROGRAMMING ROAD SPEED GOVERNOR AUXILIARY ENGINE BRAKE AUXILIARY ENGINE BRAKE CONTROL ELECTRONIC ENGINE OIL LEVEL INDICATOR FLUID FILLS ENGINE DRAIN PLUG ENGINE WARRANTY REMOTE THROTTLE HARNESS ENGINE PROGRAMMING REMOTE THROTTLE ENGINE PROGRAMMING IDLE SPEED

COOLING

2704-002 2701-010 2711-005 2708-001 2706-003 2705-002 2709-004

ENGINE FAN DRIVE ENGINE COOLING SYSTEM ENGINE COOLING SYSTEM PROTECTION ENGINE COOLANT ELECTRONIC COOLANT LEVEL INDICATOR ENGINE PUMP HEAT EXCHANGER COOLANT HOSES

AIR INTAKE

2801-005 2802-003

ENGINE AIR INTAKE AIR INTAKE PROTECTION

EXHAUST

2901-030

ENGINE EXHAUST SYSTEM

2907-003

DIESEL EXHAUST FLUID TANK

2902-010

ENGINE EXHAUST ACCESSORIES

2906-002

ENGINE EXHAUST WRAP

TRANSMISSION

1801-015 1806-003 1811-004 1815-002 1807-005 1814-002

TRANSMISSION TRANSMISSION MODE PROGRAMMING TRANSMISSION FEATURE PROGRAMMING ELECTRONIC TRANSMISSION OIL LEVEL INDICATOR TRANSMISSION SHIFT SELECTOR TRANSMISSION PRE-SELECT WITH AUXILIARY BRAKE

1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1808-007 1817-001 8005-001

TRANSMISSION COOLING SYSTEM TRANSMISSION DRAIN PLUG TRANSMISSION WARRANTY

POWER TAKE OFF

2005-009

PTO LOCATION

DRIVELINE

3001-001

DRIVELINE

3005-002 3008-085

MIDSHIP PUMP / GEARBOX MIDSHIP PUMP / GEARBOX MODEL

3048-007

MIDSHIP PUMP GEARBOX DROP

3009-007

MIDSHIP PUMP RATIO

3010-0800 MIDSHIP PUMP LOCATION C/L SUCTION TO C/L REAR AXLE 5013-010 3049-003

PUMP SHIFT CONTROLS PUMP SHIFT CONTROL PLUMBING

FUEL SYSTEMS

3109-021 3111-001 3103-008 3101-101 3130-001 3131-001 3102-007 3115-001

FUEL FILTER/WATER SEPARATOR FUEL LINES ELECTRIC FUEL PRIMER FUEL TANK FUEL TANK MATERIAL AND FINISH FUEL TANK STRAP MATERIAL FUEL TANK FILL PORT FUEL TANK DRAIN PLUG

FRONT AXLE

2401-003

FRONT AXLE

8059-013 2405-001

FRONT AXLE WARRANTY FRONT WHEEL BEARING LUBRICATION

FRONT SUSPENSION

2502-002 2501-006

FRONT SHOCK ABSORBERS FRONT SUSPENSION

STEERING

2601-006

STEERING COLUMN/WHEEL

2609-002

ELECTRONIC POWER STEERING FLUID LEVEL INDICATOR

2603-001 2606-009 2610-003 2608-001

POWER STEERING PUMP FRONT AXLE CRAMP ANGLE POWER STEERING GEAR CHASSIS ALIGNMENT

1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

REAR AXLE

3401-003 3403-001 8061-010 3411-001 3408-004

REAR AXLE REAR AXLE DIFFERENTIAL LUBRICATION REAR AXLE WARRANTY REAR WHEEL BEARING LUBRICATION VEHICLE TOP SPEED

REAR SUSPENSION

3501-032

REAR SUSPENSION

TIRES

3601-014 3602-012 3413-614 3614-013

FRONT TIRE REAR TIRE REAR AXLE RATIO TIRE PRESSURE INDICATOR

WHEELS

3701-034 3703-028 3702-002

FRONT WHEEL REAR WHEEL WHEEL TRIM

BRAKES

3205-012 3206-001 3207-005 3208-001 3204-002 3213-001 3214-001 3202-005 3215-001 3210-015

BRAKE SYSTEM FRONT BRAKES REAR BRAKES PARK BRAKE PARK BRAKE CONTROL FRONT BRAKE SLACK ADJUSTERS REAR BRAKE SLACK ADJUSTERS AIR DRYER FRONT BRAKE CHAMBERS REAR BRAKE CHAMBERS

AIR SUPPLY SYSTEMS

3320-001 3339-004 3303-001 3307-001 3309-033 3349-002 3327-002 3326-002

AIR COMPRESSOR AIR GOVERNOR MOISTURE EJECTORS AIR SUPPLY LINES AIR INLET CONNECTION AIR INLET LOCATION PLUMBING AIR INLET CONNECTION AIR INLET/OUTLET FITTING TYPE

1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 4 1 1 2 4 1

3338-002

REAR AIR TANK MOUNTING

FRAME

2103-1930 WHEELBASE 2106-0370 REAR OVERHANG 2101-002

FRAME

8007-019 2117-004 2110-101

FRAME WARRANTY FRAME CLEAR AREA FRAME PAINT

BUMPER

2201-001

FRONT BUMPER

2202-006

FRONT BUMPER EXTENSION LENGTH

2226-004

FRONT BUMPER EXTENSION FRAME WIDTH

2208-007 2211-003 2210-002 5503-022 2218-002 5501-012 2216-010 2232-002 5504-029 2217-008 2203-006

FRONT BUMPER APRON FRONT BUMPER COMPARTMENT CENTER FRONT BUMPER COMPARTMENT COVER HARDWARE MECHANICAL SIREN MECHANICAL SIREN LOCATION AIR HORN AIR HORN LOCATION AIR HORN RESERVOIR ELECTRONIC SIREN SPEAKER ELECTRONIC SIREN SPEAKER LOCATION FRONT BUMPER TOW HOOKS

CAB TILT

2301-001 2305-001

CAB TILT SYSTEM CAB TILT CONTROL RECEPTACLE

CAB GLASS

1401-009 1402-005 1407-001 1419-012 1430-001 1412-013 1431-001 1410-003 1432-001 1409-003 1433-001

CAB WINDSHIELD GLASS FRONT DOOR GLASS TINT FRONT DOOR GLASS REAR DOOR RIGHT HAND GLASS TINT REAR DOOR RIGHT HAND GLASS REAR DOOR LEFT HAND GLASS TINT REAR DOOR LEFT HAND GLASS SIDE MID RIGHT HAND GLASS TINT SIDE MID RIGHT HAND GLASS SIDE MID LEFT HAND GLASS TINT SIDE MID LEFT HAND

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 5

CLIMATE CONTROL

1614-202 1632-002 1617-103 1620-015 1603-003 1601-013 1530-001

CLIMATE CONTROL CLIMATE CONTROL DRAIN CLIMATE CONTROL ACTIVATION HVAC OVERHEAD COVER PAINT A/C CONDENSER LOCATION A/C COMPRESSOR UNDER CAB INSULATION

1308-001 1332-008 1345-002 1301-003 1337-001 1304-001 1335-017 1371-017 1370-019 1378-018 1373-018 1344-002 1312-006 1313-014 1314-001

CAB INTERIOR

1327-001 1302-001 1368-002 1306-006 1305-013 1339-102 1321-004 1307-002 5040-053 1303-017 1379-003 1102-013 1323-001 1105-002

INTERIOR TRIM FLOOR INTERIOR TRIM REAR WALL INTERIOR TRIM HEADER TRIM TRIM CENTER DASH TRIM LEFT HAND DASH TRIM RIGHT HAND DASH ENGINE TUNNEL TRIM POWER POINT DASH MOUNT STEP TRIM UNDER CAB ACCESS DOOR INTERIOR DOOR TRIM DOOR TRIM CUSTOMER NAMEPLATE CAB DOOR TRIM REFLECTIVE INTERIOR GRAB HANDLE "A" PILLAR INTERIOR GRAB HANDLE FRONT DOOR INTERIOR GRAB HANDLE REAR DOOR INTERIOR SOFT TRIM COLOR INTERIOR TRIM SUNVISOR INTERIOR FLOOR MAT COLOR CAB PAINT INTERIOR DOOR TRIM HEADER TRIM INTERIOR PAINT TRIM CENTER DASH INTERIOR PAINT TRIM LEFT HAND DASH INTERIOR PAINT TRIM RIGHT HAND DASH INTERIOR PAINT DASH PANEL GROUP SWITCHES CENTER PANEL SWITCHES LEFT PANEL SWITCHES RIGHT PANEL

CAB SEATS

1225-018 1237-001 1243-001

SEAT BELT WARNING SEAT MATERIAL SEAT COLOR

1 1 1 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1249-039 1201-005 1213-025 1219-001 8102-103 1202-009 1214-037 1220-002 8103-103 1273-001 1263-001 1203-009 1215-034 1221-009 8104-103 1311-101 1355-019

SEAT BACK LOGO SEAT DRIVER SEAT BACK DRIVER SEAT MOUNTING DRIVER OCCUPANT PROTECTION DRIVER SEAT OFFICER SEAT BACK OFFICER SEAT MOUNTING OFFICER OCCUPANT PROTECTION OFFICER SEAT BELT ORIENTATION CREW SEAT REAR FACING OUTER LOCATION SEAT CREW REAR FACING OUTER SEAT BACK REAR FACING OUTER SEAT MOUNTING REAR FACING OUTER OCCUPANT PROTECTION RFO CAB FRONT UNDERSEAT STORAGE ACCESS DOOR SEAT COMPARTMENT DOOR FINISH

CAB EXTERIOR

1511-003 1534-002 1103-002 1111-001 1503-002 1504-013 1529-002 1513-010 1514-002

WINDSHIELD WIPER SYSTEM ELECTRONIC WINDSHIELD FLUID LEVEL INDICATOR CAB DOOR HARDWARE DOOR LOCKS GRAB HANDLES REARVIEW MIRRORS REARVIEW MIRROR HEAT SWITCH CAB FENDER MUD FLAPS FRONT

START / CHARGING SYSTEMS

5109-001 5101-002 5106-003 5107-007 5102-001 5108-002 5104-002

IGNITION BATTERY BATTERY TRAY BATTERY BOX COVER BATTERY CABLE BATTERY JUMPER STUD ALTERNATOR

LINE VOLTAGE ELECTRICAL POWER DISTRIBUTION

5202-004 5203-002 3314-006 5204-055

BATTERY CONDITIONER BATTERY CONDITIONER DISPLAY AUXILIARY AIR COMPRESSOR ELECTRICAL INLET

1 1 1 1 7 4 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

5209-002 5210-005 5206-002

ELECTRICAL INLET LOCATION ELECTRICAL INLET CONNECTION ELECTRICAL INLET COLOR

5303-004 5337-001 5336-003 5302-003 5350-050 5308-005 5309-003 5382-002 5312-001 5317-097 5335-002 5329-003 5306-065 5318-004 5316-003 5305-152

LIGHTING

5301-100

HEADLIGHTS FRONT TURN SIGNALS HEADLIGHT LOCATION SIDE TURN/MARKER LIGHTS MARKER & ICC LIGHTS HEADLIGHT AND MARKER LIGHT ACTIVATION GROUND LIGHTS LOWER CAB STEP LIGHTS INTERMEDIATE STEP LIGHTS ENGINE COMPARTMENT LIGHT FRONT SCENE LIGHTS FRONT SCENE LIGHTS ACTIVATION FRONT SCENE LIGHT LOCATION SIDE SCENE LIGHTS SIDE SCENE LIGHT LOCATION SIDE SCENE ACTIVATION INTERIOR OVERHEAD LIGHTS

OPTICAL WARNING DEVICES

5406-001 5422-001 5409-002 5425-002 5401-002 5413-002 5423-007 5404-002 5419-002 5420-002 5402-002 5418-002 5412-002 5424-008 5411-002

DO NOT MOVE APPARATUS LIGHT MASTER WARNING SWITCH HEADLIGHT FLASHER HEADLIGHT FLASHER SWITCH INBOARD FRONT WARNING LIGHTS INBOARD FRONT WARNING LIGHTS COLOR FRONT WARNING SWITCH INTERSECTION WARNING LIGHTS INTERSECTION WARNING LIGHTS COLOR INTERSECTION WARNING LIGHTS LOCATION SIDE WARNING LIGHTS SIDE WARNING LIGHTS COLOR SIDE WARNING LIGHTS LOCATION SIDE AND INTERSECTION WARNING SWITCH TANK LEVEL LIGHTS

AUDIBLE WARNING DEVICES

5510-004 5514-002

SIREN CONTROL HEAD HORN BUTTON SELECTOR SWITCH

1 1 8 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

5512-003 5513-002 5505-002

AIR HORN ACTIVATION MECHANICAL SIREN ACTIVATION BACK-UP ALARM

INSTRUMENTATION

5601-019 5624-001

INSTRUMENTATION BACKLIGHTING COLOR

COMMUNICATIONS SYSTEMS

5703-010 5708-002 5020-001

COMMUNICATION ANTENNA COMMUNICATION ANTENNA CABLE ROUTING PANEL LAYOUT

ADDITIONAL EQUIPMENT

8814-002 8806-001 8807-002 8810-001 8811-003

CAB EXTERIOR PROTECTION FIRE EXTINGUISHER ROAD SAFETY KIT DOOR KEYS DIAGNOSTIC SOFTWARE OCCUPANT PROTECTION

SALES ADMIN

8003-140 8017-001 8030-006 8031-023 8805-007 8039-001

WARRANTY CAB AND CHASSIS LABELING LANGUAGE CHASSIS OPERATION MANUAL ENGINE & TRANSMISSION OPERATION MANUAL CAB/CHASSIS AS BUILT WIRING DIAGRAMS SALES TERMS

ENGINEERING

9005-002

DRIVELINE LAYOUT CONFIRMATION

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 9

Specification

MODEL

The chassis shall be a Metro Star model. The cab and chassis shall include design considerations for multiple emergency vehicle applications, rapid transit and maneuverability. The chassis shall be manufactured for heavy duty service with the strength and capacity to support a fully laden apparatus, one hundred (100) percent of the time.

MODEL YEAR

The chassis shall have a vehicle identification number that reflects a 2017 model year.

COUNTRY OF SERVICE

The chassis shall be put in service in the country of United States of America (USA). The chassis will meet applicable U.S.A. federal motor vehicle safety standards per CFR Title 49 Chapter V Part 571 as clarified in the incomplete vehicle book per CFR Title 49 Chapter V Part 568 Section 4 which accompanies each chassis. Spartan Chassis is not responsible for compliance to state, regional, or local regulations. Dealers should identify those regulations and order any necessary optional equipment from Spartan Chassis or their OEM needed to be in compliance with those regulations.

APPARATUS TYPE

The apparatus shall be a pumper vehicle designed for emergency service use which shall be equipped with a permanently mounted fire pump which has a minimum rated capacity of 750 gallons per minute (3000 L/min). The apparatus shall include a water tank and hose body whose primary purpose is to combat structural and associated fires.

VEHICLE TYPE

The chassis shall be manufactured for use as a straight truck type vehicle and designed for the installation of a permanently mounted apparatus behind the cab. The apparatus of the vehicle shall be supplied and installed by the apparatus manufacturer.

AXLE CONFIGURATION

The chassis shall feature a 4 x 2 axle configuration consisting of a single rear drive axle with a single front steer axle.

GROSS AXLE WEIGHT RATINGS FRONT

The front gross axle weight rating (GAWR) of the chassis shall be 20,000 pounds.

This front gross axle weight rating shall be adequate to carry the weight of the completed apparatus including all equipment and personnel.

GROSS AXLE WEIGHT RATINGS REAR

The rear gross axle weight rating (GAWR) of the chassis shall be 27,000 pounds. This rear gross axle weight rating shall be adequate to carry the weight of the completed apparatus including all equipment and personnel.

PUMP PROVISION

The chassis shall include provisions to mount a drive line pump in the middle of the chassis, behind the cab, more commonly known as the midship location.

CAB STYLE

The cab shall be a custom, fully enclosed, EMFD model with a 10.00 inch raised roof over the driver, officer, and crew area, designed and built specifically for use as an emergency response vehicle by a company specializing in cab and chassis design for all emergency response applications. The cab shall be designed for heavy-duty service utilizing superior strength and capacity for the application of protecting the occupants of the vehicle. This style of cab shall offer up to eight (8) seating positions. The cab shall incorporate a fully enclosed design with side wall roof supports, allowing for a spacious cab area with no partition between the front and rear sections of the cab. To provide a superior finish by reducing welds that fatigue cab metal; the roof, the rear wall and side wall panels shall be assembled using a combination of welds and proven industrial adhesives designed specifically for aluminum fabrication for construction. The cab shall be constructed using multiple aluminum extrusions in conjunction with aluminum plate, which shall provide proven strength and the truest, flattest body surfaces ensuring less expensive paint repairs if needed. All aluminum welding shall be completed to the American Welding Society and ANSI D1.2-96 requirements for structural welding of aluminum. All interior and exterior seams shall be sealed for optimum noise reduction and to provide the most favorable efficiency for heating and cooling retention. The cab shall be constructed of 5052-H32 corrosion resistant aluminum plate. The cab shall incorporate tongue and groove fitted 6061-T6 0.13 & 0.19 inch thick aluminum extrusions for extreme duty situations. A single formed, one (1) piece extrusion shall be used for the “A” pillar, adding strength and rigidity to the cab as well as additional roll-over protection. The cab side walls and lower roof skin shall be 0.13 inch thick; the rear wall and raised roof skins shall be 0.09 inch thick; the front cab structure shall be 0.19 inch thick. The exterior width of the cab shall be 94.00 inches wide with a minimum interior width of 88.00 inches. The overall cab length shall be 137.10 inches with 60.00 inches from the centerline of the front of the axle to the back of the cab.

The cab interior shall be designed to afford the maximum usable interior space and attention to ergonomics with hip and legroom while seated which exceeds industry standards. The crew cab floor shall be flat across the entire walking area for ease of movement inside the cab. The cab shall offer an interior height of 57.50 inches from the front floor to the headliner and a rear floor to headliner height of 65.00 inches in the raised roof area, at a minimum. The cab shall offer an interior measurement at the floor level from the rear of the engine tunnel to the rear wall of the cab of 57.88 inches. All interior measurements shall include the area within the interior trimmed surfaces and not to any unfinished surface. The cab shall include a driver and officer area with two (2) cab doors large enough for personnel in full firefighting gear. The front doors shall offer a clear opening of 40.25 inches wide X 53.50 inches high, from the cab floor to the top of the door opening. The cab shall also include a crew area with up to two (2) cab doors, also large enough for personnel in full firefighting gear. The rear doors shall offer a clear opening of 32.25 inches wide X 61.00 inches high, from the cab floor to the top of the door opening. The cab shall incorporate a progressive two (2) step configuration from the ground to the cab floor at each door opening. The progressive steps are vertically staggered and extend the full width of each step well allowing personnel in full firefighting gear to enter and exit the cab easily and safely.

The first step for the driver and officer area shall measure approximately 11.50 inches deep X 31.13 inches wide. The intermediate step shall measure approximately 8.50 inches deep X 32.50 inches wide. The height from the first step to the intermediate step and the intermediate step to the cab floor shall not exceed 11.00 inches. The first step for the crew area shall measure approximately 11.50 inches deep X 20.44 inches wide. The intermediate step shall measure approximately 10.25 inches deep X 22.75 inches wide. The height from the first step to the intermediate step and the intermediate step to the cab floor shall not exceed 12.80 inches.

OCCUPANT PROTECTION

The vehicle shall include the Advanced Protection System™ (APS) which shall secure belted occupants and increase the survivable space within the cab. The APS shall selectively deploy integrated systems to protect against injuries in qualifying frontal impact, side impact, and rollover events. The increase in survivable space and security of the APS shall also provide ejection mitigation protection. The system components shall include: • Driver steering wheel airbag • Driver dual knee air bags (patent pending) with energy management mounting (patent pending) and officer knee airbag. • Large driver, officer, and crew area side curtain airbags • APS advanced seat belt system - retractor pre-tensioners tighten the seat belts around the occupants, securing the occupants in seats and load limiters play out some of the seat belt

webbing to reduce seat belt to chest and torso force upon impact as well as mitigate head and neck injuries • Heavy truck Restraints Control Module (RCM) - receives inputs from the outboard sensors, selectively deploys APS systems, and records sensory inputs immediately before and during a detected qualifying event • Integrated outboard crash sensors mounted at the perimeter of the vehicle - detects a qualifying front or side impact event and monitors and communicates vehicle status and real time diagnostics of all critical subsystems to the RCM • Fault-indicating Supplemental Restraint System (SRS) light on the driver’s instrument panel Frontal impact protection shall be provided by the outboard sensors and the RCM. In a qualifying front impact event the outboard sensors provide inputs to the RCM. The RCM activates the steering wheel airbag, driver side dual knee airbags (patent pending), officer side knee airbag, and advanced seat belts for each occupant in the cab. The APS frontal impact system shall be independently tested to ensure occupant injury criteria does not exceed injury criteria defined in Federal Motor Vehicle Safety Standard (FMVSS) 208. Frontal impact into a rigid barrier at 25 mph shall be conducted by an independent third party test facility using belted 95 th percentile Hybrid II test dummies. Rollover, side impact, and ejection mitigation shall be provided by the outboard sensors and the RCM. In qualifying rollover or side impact events the outboard sensors provide inputs to the RCM. The RCM activates the side curtain airbags and advanced seat belts for each occupant in the cab. The RCM measures roll angle, lateral acceleration, and roll rate to determine if a rollover event or side impact event is imminent or occurring. In the event of a qualifying offset or other non-frontal impact, the RCM shall determine and intelligently deploy the front impact protection system, the side impact protection system, or both front and side impact protection systems based on the inputs received from the outboard crash sensors. The APS side impact system shall be independently tested to ensure occupant injury criteria does not exceed injury criteria defined in Federal Motor Vehicle Safety Standard (FMVSS) 214. Side impact from a moving barrier at 17 mph shall be conducted by an independent third party test facility using belted 50 th percentile ES-2re test dummies.

CAB FRONT FASCIA

The front cab fascia shall be constructed of 5052-H32 Marine Grade, 0.13 of an inch thick aluminum plate which shall be an integral part of the cab. The fascia shall be Sirius II styled, offering an aerodynamic look for a stylish appearance. The cab fascia shall encompass the front of the aluminum cab structure from the bottom of the windshield to the lower section of the cab. The Sirius II style cab fascia shall include provisions for headlights, turn signals and warning light assemblies designed to permit easy access for maintenance. The fascia shall include additional intake provisions at the lower portion just above the bumper further enhancing the total free air intake for engine cooling.

Chrome plated molded plastic bezels shall be provided for lighting assemblies located on each side of the cab fascia for optimum visibility.

FRONT GRILLE

The Sirius II fascia shall include a two (2) piece front grille. The upper portion of the grille shall be hinged to provide service access behind the grille.

CAB UNDERCOAT

There shall be a rubberized undercoating applied to the underside of the cab that provides abrasion protection, sound deadening and corrosion protection.

CAB SIDE DRIP RAIL

There shall be a drip rail along the top radius of each cab side. The drip rails shall help prevent water from the cab roof running down the cab side.

CAB PAINT EXTERIOR

The cab shall be painted prior to the installation of glass accessories and all other cab trim to ensure complete paint coverage and the maximum in corrosion protection of all metal surfaces. All metal surfaces on the entire cab shall be ground by disc to remove any surface oxidation or surface debris which may hinder the paint adhesion. Once the surface is machine ground a high quality acid etching of base primer shall be applied. Upon the application of body fillers and their preparation, the cab shall be primed with a coating designed for corrosion resistance and surface paint adhesion. The maximum thickness of the primer coat shall be 2.00 mils. The entire cab shall then be coated with an intermediate solid or epoxy surfacing agent that is designed to fill any minor surface defects, provide an adhesive bond between the primer and the paint and improve the color and gloss retention of the color. The finish to this procedure shall be a sanding of the cab with 360 grit paper followed by sealing the seams with SEM brand seam sealer. The cab shall then be painted the specific color designated by the customer with an acrylic urethane type system designed to retain color and resist acid rain and most atmospheric chemicals found on the fire ground or emergency scene. The paint shall have a minimum thickness of 2.00 mils, followed by a clear top coat not to exceed 2.00 mils. The entire cab shall then be baked at 180 degrees for one (1) hour to speed the curing process of the coatings.

CAB PAINT MANUFACTURER

The cab shall be painted with PPG Industries paint.

CAB PAINT PRIMARY/LOWER COLOR

The primary/lower paint color shall be:

CAB PAINT SECONDARY/UPPER COLOR

The secondary/upper paint color shall be:

CAB PAINT EXTERIOR BREAKLINE

The upper and lower paint shall meet at a breakline on the cab which shall be located approximately 0.50 inch below the cab door windows on each side of the cab. The breakline shall curve downward at the front cab corners to approximately 6.50 inches below the windshields on the front of the cab ending at either side of the upper grille.

CAB PAINT PINSTRIPE

Where the upper and lower paint colors meet a temporary 0.50 inch wide black pinstripe shall be applied over this break line to offer a more finished look prior to the final pinstripe being installed by the OEM.

CAB PAINT WARRANTY

The cab and chassis shall be covered by a limited manufacturer paint warranty which shall be in effect for ten (10) years from the first owner’s date of purchase or in service or the first 100,000 actual miles, whichever occurs first.

CAB PAINT INTERIOR

The visible interior cab structure surfaces shall be painted with a multi-tone silver gray texture finish.

CAB ENTRY DOORS

The cab shall include four (4) entry doors, two (2) front doors and two (2) crew doors designed for ease of entering and egress when outfitted with an SCBA. The doors shall be constructed of extruded aluminum with a nominal thickness of 0.13 inch. The exterior skins shall be constructed of 0.13 inch aluminum plate. The doors shall include a double rolled style automotive rubber seal around the perimeter of each door frame and door edge which ensures a weather tight fit. All door hinges shall be hidden within flush mounted cab doors for a pleasing smooth appearance and perfect fit along each side of the cab. Each door hinge shall be piano style with a 0.38 inch pin and shall be constructed of stainless steel.

CAB ENTRY DOOR TYPE

All cab entry doors shall be full length in design to fully enclose the lower cab steps.

CAB INSULATION

The cab ceiling and walls shall include 1.00 inch thick foam insulation. The insulation shall act as a barrier absorbing noise as well as assisting in sustaining the desired climate within the cab interior.

CAB STRUCTURAL WARRANTY

Summary of Warranty Terms: THE FOLLOWING IS SUMMARY OF WARRANTY TERMS FOR INFORMATION ONLY. THE ACTUAL LIMITED WARRANTY DOCUMENT, WHICH IS ATTACHED TO THIS OPTION, CONTAINS THE COMPLETE STATEMENT OF THE SPARTAN MOTORS USA LIMITED WARRANTY. SPARTAN’S RESPONSIBILITY IS TO BE ACCORDING TO THE TERMS OF THE COMPLETE LIMITED WARRANTY DOCUMENT. The cab structure shall be warranted for a period of ten (10) years or one hundred thousand (100,000) miles which ever may occur first. The warranty period shall commence on the date the vehicle is delivered to the first end user.

CAB TEST INFORMATION

The cab shall have successfully completed the preload side impact, static roof load application and frontal impact without encroachment to the occupant survival space when tested in accordance with Section 4 of SAE J2420 COE Frontal Strength Evaluation Dynamic Loading Heavy Trucks, Section 5 of SAE J2422 Cab Roof Strength Evaluation Quasi –Static Loading Heavy Trucks and ECE R29 Uniform Provisions Concerning the Approval of Vehicles with regard to the Protection of the Occupants of the Cab of a Commercial Vehicles Annex 3 Paragraph 5. The above tests have been witnessed by and attested to by an independent third party. The test results were recorded using cameras, high speed imagers, accelerometers and strain gauges. Documentation of the testing shall be provided upon request.

ELECTRICAL SYSTEM

The chassis shall include a single starting electrical system which shall include a 12 volt direct current system, suppressed per SAE J551. The wiring shall be appropriate gauge cross link with 311 degree Fahrenheit insulation. All SAE wires in the chassis shall be color coded and shall include the circuit number and function where possible. The wiring shall be protected by 275 degree Fahrenheit minimum high temperature flame retardant loom.

DATA RECORDING SYSTEM

The chassis shall have a Weldon Vehicle Data Recorder (VDR) system installed. The system shall be designed to meet NFPA 1901. The following information shall be recorded: • Vehicle Speed • Acceleration • Deceleration • Engine Speed • Engine Throttle Position • ABS Event • Seat Occupied Status • Seat Belt Status

• Master Optical Warning Device Switch Position • Service Brake • Engine Hours • Time • Date Each portion of the data shall be recorded at the specified intervals and stored for the specified length of time to meet NFPA 1901 guidelines and shall be retrievable by connecting a laptop computer to the VDR system. The laptop connection shall be a panel mounted female type B USB connection point, remotely mounted in the left side foot well of the cab.

ACCESSORY POWER

The electrical distribution panel shall include two (2) power studs. The studs shall be size #10 and each of the power studs shall be circuit protected with a fuse of the specified amperage. One (1) power stud shall be capable of carrying up to a 40 amp battery direct load. One (1) power stud shall be capable of carrying up to a 15 amp ignition switched load. The two (2) power studs shall share one (1) #10 ground stud. A 225 amp battery direct power and ground stud shall be provided and installed on the chassis near the left hand battery box for OEM body connections.

EXTERIOR ELECTRICAL TERMINAL COATING

All terminals exposed to the elements will be sprayed with a high visibility protective rubberized coating to prevent corrosion.

ENGINE

The chassis engine shall be a Cummins ISL9 engine. The ISL9 engine shall be an in-line six (6) cylinder, four cycle diesel powered engine. The engine shall offer a rating of 380 horse power at 1900 RPM and shall be governed at 2100 RPM. The torque rating shall feature 1150 foot pounds of torque at 1400 RPM with 543 cubic inches (8.9 liters) of displacement. The ISL9 engine shall feature a VGT™ Turbocharger, a high pressure common rail fuel system, fully integrated electronic controls with an electronic governor, and shall be EPA certified to meet the 2013 emissions standards using cooled exhaust gas recirculation and selective catalytic reduction technology. The engine shall include an engine mounted combination full flow/by-pass oil filter with replaceable spin on cartridge for use with the engine lubrication system. The engine shall include Citgo brand Citgard 500, or equivalent SAE 15W40 CJ4 low ash engine oil which shall be utilized for proper engine lubrication. A wiring harness shall be supplied ending at the back of the cab. The harness shall include a connector which shall allow an optional harness for the pump panel. The included circuits shall be provided for a tachometer, oil pressure, engine temperature, hand throttle, high idle and a PSG system. A circuit for J1939 data link shall also be provided at the back of the cab.

CAB ENGINE TUNNEL

The cab interior shall include an integrated engine tunnel constructed of 5052-H32 Marine Grade, 0.19 of an inch thick aluminum. The tunnel shall be a maximum of 41.50 inches wide X 25.50 inches high.

DIESEL PARTICULATE FILTER CONTROLS

There shall be two (2) controls for the diesel particulate filter. One (1) control shall be for regeneration and one (1) control shall be for regeneration inhibit.

ENGINE PROGRAMMING HIGH IDLE SPEED

The engine high idle control shall maintain the engine idle at approximately 1250 RPM when engaged.

ENGINE HIGH IDLE CONTROL

The vehicle shall be equipped with a high-idle speed control rocker switch, which shall be pre-set to maintain the engine idle at a pre-determined rate when activated manually. This device shall operate when the master switch is activated and safely interlocked only to function when the transmission is in neutral with the parking brake set.

ENGINE PROGRAMMING ROAD SPEED GOVERNOR

The engine shall include programming which will govern the top speed of the vehicle.

AUXILIARY ENGINE BRAKE

The engine shall utilize a variable geometry turbo (VGT). The VGT auxiliary engine brake shall be an integral part of the turbo and shall offer a variable rate of exhaust flow, which when activated shall slow the engine and in turn slow the vehicle. The VGT shall actuate the vehicle’s brake lights when engaged as an auxiliary brake. A cutout relay shall be installed to disable the VGT when in pump mode or when an ABS event occurs. The VGT engine brake shall activate at a 0% accelerator throttle position when in operation mode.

AUXILIARY ENGINE BRAKE CONTROL

An engine variable geometry turbo brake control device shall be included. The electronic control device shall monitor various conditions and shall activate the engine brake only if all of the following conditions are simultaneously detected: • A valid gear ratio is detected. • The driver has requested or enabled engine compression brake operation. • The throttle is at a minimum engine speed position. • The electronic controller is not presently attempting to execute an electronically controlled final drive gear shift. The variable geometry turbo brake control shall be controlled through an on/off rocker switch.

ELECTRONIC ENGINE OIL LEVEL INDICATOR

The engine oil shall be monitored electronically and shall send a signal to activate a warning in the instrument panel when levels fall below normal. The warning shall activate in a low oil situation upon turning on the master battery and ignition switches without the engine running.

FLUID FILLS

The front of the chassis shall accommodate fluid fill for the engine oil through the grille. This area shall also accommodate a check for the engine oil. The transmission, power steering, and coolant fluid fills and checks shall be under the cab. The windshield washer fill shall be accessible through the front left side mid step.

ENGINE DRAIN PLUG

The engine shall include an original equipment manufacturer installed oil drain plug.

ENGINE WARRANTY

The Cummins engine shall be warranted for a period of five (5) years or 100,000 miles, whichever occurs first.

REMOTE THROTTLE HARNESS

An apparatus interface wiring harness for the engine and transmission pump interlocks shall be supplied with the chassis. The harness shall include a connector for connection to a chassis pump panel harness supplied by the body builder and shall terminate in the left frame rail behind the cab for connection by the body builder. The harness shall include circuits deemed for a pump panel and shall contain circuits for a hand throttle, and a multiplexed gauge. Separate circuits shall also be included for a pump control switch, “Pump Engaged” and “OK to Pump” indicator lights, open compartment ground, start signal, park brake ground, ignition signal, master power, clean power, customer ignition, air horn solenoid switch, high idle switch and high idle indicator light.

ENGINE PROGRAMMING REMOTE THROTTLE

The engine ECM (Electronic Control Module) discreet wire remote throttle circuit shall be turned off for use with a J1939 based pump controller or when the discreet wire remote throttle controls are not required.

ENGINE PROGRAMMING IDLE SPEED

The engine low idle speed will be programmed at 700 rpm.

ENGINE FAN DRIVE

The engine cooling system fan shall incorporate a thermostatically controlled, Horton clutched type fan drive. When the clutched fan is disengaged it shall facilitate improved vehicle performance, cab heating in cold climates, and fuel economy. The fan clutch design shall be fail safe so that if the clutch drive fails the fan shall engage to prevent engine overheating due to the fan clutch failure.

ENGINE COOLING SYSTEM

There shall be a heavy-duty aluminum cooling system designed to meet the demands of the emergency response industry. The cooling system shall have the capacity to keep the engine properly cooled under all conditions of road and pumping operations. The cooling system shall be designed and tested to meet or exceed the requirements specified by the engine and transmission manufacturer and all EPA requirements. The complete cooling system shall be mounted to isolate the entire system from vibration or stress. The individual cores of the cooling system shall be mounted in a manner to allow expansion and contraction at various rates without inducing stress into the adjoining cores. The cooling system shall utilize a charge air cooler to radiator serial flow package that provides the maximum cooling capacity for the specified engine as well as serviceability. The main components shall include a surge tank, an air to air charge air cooler bolted to the front of the radiator, recirculation shields, a shroud, a fan, and required tubing. The radiator shall be a down-flow design constructed with aluminum cores, plastic end tanks, and a steel frame. The radiator shall be equipped with a drain cock to drain the coolant for serviceability. The cooling system shall include a one piece injection molded polymer eleven (11) blade fan with a fiberglass fan shroud. The cooling system shall be equipped with a surge tank that is capable of removing entrained air from the system. The surge tank shall be equipped with a low coolant probe and sight glass to monitor the level of the coolant. The surge tank shall have a dual seal cap that meets the engine manufacturer's pressure requirements, and allows for expansion and recovery of coolant into a separate integral expansion chamber. All radiator tubes shall be formed from aluminized steel tubing. Recirculation shields shall be installed where required to prevent heated air from reentering the cooling package and affecting performance. The charge air cooler shall be a cross-flow design constructed completely of aluminum with cast tanks. All charge air cooler tubes shall be formed from aluminized steel tubing and installed with silicone hump hoses and stainless steel “constant torque” style clamps meeting the engine manufacturer’s requirements.

ENGINE COOLING SYSTEM PROTECTION

The engine cooling system shall include a recirculation shield designed to act as a light duty skid plate below the radiator to provide additional protection for the engine cooling system from light impacts, stones, and road debris. The skid plate shall be painted to match the frame color.

ENGINE COOLANT

The cooling package shall include Extended Life Coolant (ELC). The use of ELC provides longer intervals between coolant changes over standard coolants providing improved performance. The coolant shall contain a 50/50 mix of ethylene glycol and de-ionized water to keep the coolant from freezing to a temperature of -34 degrees Fahrenheit.

Proposals offering supplemental coolant additives (SCA) shall not be considered, as this is part of the extended life coolant makeup.

ELECTRONIC COOLANT LEVEL INDICATOR

The instrument panel shall feature a low engine coolant indicator light which shall be located in the center of the instrument panel. An audible tone alarm shall also be provided to warn of a low coolant incident.

ENGINE PUMP HEAT EXCHANGER

A single bundle type coolant to water heat exchanger shall be installed between the engine and the radiator. The heat exchanger shall be designed to prohibit water from the pump from coming in contact with the engine coolant. This shall allow the use of water from the discharge side of the pump to assist in cooling the engine.

COOLANT HOSES

The cooling system hoses shall be silicone heater hose with rubber hoses in the cab interior. The radiator hoses shall be formed silicone coolant hoses with formed aluminized steel tubing. All heater hose, silicone coolant hose, and tubing shall be secured with stainless steel constant torque band clamps.

ENGINE AIR INTAKE

The engine air intake system shall include an ember separator air intake filter which shall be located in the front of the cab behind the right hand side fascia. This filter shall protect the downstream air filter from embers using a combination of unique flat and crimped metal screens constructed into a corrosion resistant steel frame. This multilayered screen shall be designed to trap embers or allow them to burn out before passing through the pack, while creating only minimal air flow restriction through the system. Periodic cleaning or replacement of the screen shall be all that is required after installation. The engine shall also include an air intake filter which shall be bolted to the frame and located under the front of the cab on the right hand side. The system shall utilize a replaceable dry type filter which ensures dust and debris remains safely contained inside the housing during operation via leak-tight seals. The service cover shall be located on the bottom of the housing, eliminating the chance of contaminating the air intake system during air filter service. The air flow distribution and dust loading shall be uniform throughout the high-performance filter element, which shall result in pressure differential for improved horsepower and fuel economy. The air intake ember separator shall be mounted within easy access via a hinged panel behind the right hand side headlight module. The air intake system shall include a restriction indicator light in the warning light cluster on the instrument panel, which shall activate when the air cleaner element requires replacement.

AIR INTAKE PROTECTION

A light duty skid plate shall be supplied for the engine air intake system below the right front side of the cab. The skid plate shall provide protection for the air intake system from light impacts, stones, and road debris. The skid plate shall be painted to match the frame color.

ENGINE EXHAUST SYSTEM

The exhaust system shall be mounted below the frame in the outboard position with the SCR canister in line rearward of the DPF. The exhaust system shall utilize a 90-degree bend in the exhaust tubing from the turbo into a side inlet DPF canister that allows the entire system to be pulled forward. The discharge shall terminate horizontally on the right side of the vehicle ahead of the rear tires.

The exhaust system shall include a diesel particulate filter (DPF), a diesel oxidation catalyst, and a selective catalytic reduction (SCR) catalyst to meet current EPA standards. The selective catalytic reduction catalyst utilizes a diesel exhaust fluid solution consisting of urea and purified water to convert NOx into nitrogen, water, and trace amounts of carbon dioxide. The solution shall be injected into the system through the decomposition tube between the DPF and SCR. The system shall utilize 0.07 inch thick stainless steel exhaust tubing between the engine turbo and the DPF. Zero leak clamps seal all system joints between the turbo and DPF. The DPF, the decomposition tube, and the SCR canister through the end of the tailpipe shall be connected with zero leak clamps.

DIESEL EXHAUST FLUID TANK

The exhaust system shall include a molded cross linked polyethylene tank for Diesel Exhaust Fluid (DEF). The tank shall have a capacity of six (6) usable gallons and shall be mounted on the left hand side of the chassis frame behind the batteries below the frame. The DEF tank shall be designed with capacity for expansion in case of fluid freezing. Engine coolant, which shall be thermostatically controlled, shall be run through lines in the tank to help prevent the DEF from freezing and to provide a means of thawing the fluid if it should become frozen. The tank fill tube shall be routed under the rear of the cab with the fill neck and splash guard accessible in the top rear step.

ENGINE EXHAUST ACCESSORIES

An exhaust temperature mitigation device shall be shipped loose for installation by the body manufacturer on the vehicle. The temperature mitigation device shall lower the temperature of the exhaust by combining ambient air with the exhaust gasses at the exhaust outlet.

ENGINE EXHAUST WRAP

The exhaust tubing between the engine turbo and the diesel particulate filter (DPF) shall be wrapped with a thermal cover in order to retain the necessary heat for DPF regeneration. The exhaust wrap shall also help protect surrounding components from radiant heat which can be transferred from the exhaust.

TRANSMISSION

The drive train shall include an Allison model EVS 3000 torque converting, automatic transmission which shall include electronic controls. The transmission shall feature two (2) 10-bolt PTO pads located on the converter housing. The transmission shall include two (2) internal oil filters and Castrol TranSynd™ synthetic TES 295 transmission fluid which shall be utilized in the lubrication of the EVS transmission. An electronic oil level sensor shall be included with the readout located in the shift selector. The transmission gear ratios shall be: 1st 3.49:1 2nd 1.86:1 3rd 4th 1.41:1 1.00:1 5th 0.75:1 6th 0.65:1 (if applicable) Rev 5.03:1

TRANSMISSION MODE PROGRAMMING

The transmission, upon start-up, will select five (5) speeds of operation. The sixth speed over drive shall be available with the activation of the mode button on the shifting pad.

TRANSMISSION FEATURE PROGRAMMING

The Allison Gen V-E transmission EVS group package number 127 shall contain the 198 vocational package in consideration of the duty of this apparatus as a pumper. This package shall incorporate an automatic neutral with selector override. This feature commands the transmission to neutral when the park brake is applied, regardless of drive range requested on the shift selector. This requires re-selecting drive range to shift out of neutral for the override. This package shall be coupled with the use of a split shaft PTO and incorporate pumping circuits. These circuits shall be used allowing the vehicle to operate in the fourth range lockup while operating the pump mode due to the 1 to 1 ratio through the transmission, therefore the output speed of the engine is the input speed to the pump. The pump output can be easily calculated by using this input speed and the drive ratio of the pump itself to rate the gallons of water the pump can provide. A transmission interface connector shall be provided in the cab. This package shall contain the following input/output circuits to the transmission control module. The Gen V-E transmission shall include prognostic diagnostic capabilities. These capabilities shall include the monitoring of the fluid life, filter change indication, and transmission clutch maintenance. Wire assignment Function ID Description Inputs C J Outputs PTO Request Fire Truck Pump Mode (4th Lockup) 142 122 / 123 C G Range Indicator PTO Enable Output Signal Return 145 (4th) 130 103

ELECTRONIC TRANSMISSION OIL LEVEL INDICATOR

The transmission fluid shall be monitored electronically and shall send a signal to activate a warning in the instrument panel when levels fall below normal.

TRANSMISSION SHIFT SELECTOR

An Allison pressure sensitive range selector touch pad shall be provided and located to the right of the driver within clear view and easy reach. The shift selector shall have a graphical Vacuum Florescent Display (VFD) capable of displaying two lines of text. The shift selector shall provide mode indication and a prognostic indicator (wrench symbol) on the digital display. The prognostics monitor various operating parameters and shall alert you when a specific maintenance function is required.

TRANSMISSION PRE-SELECT WITH AUXILIARY BRAKE

When the auxiliary brake is engaged, the transmission shall automatically shift to second gear to decrease the rate of speed assisting the secondary braking system and slowing the vehicle.

TRANSMISSION COOLING SYSTEM

The transmission shall include a water to oil cooler system located in the cooling loop between the radiator and the engine. The transmission cooling system shall meet all transmission manufacturer requirements. The transmission cooling system shall feature continuous flow of engine bypass water to maintain uninterrupted transmission cooling.

TRANSMISSION DRAIN PLUG

The transmission shall include an original equipment manufacturer installed magnetic transmission fluid drain plug.

TRANSMISSION WARRANTY

The Allison EVS series transmission shall be warranted for a period of five (5) years with unlimited mileage. Parts and labor shall be included in the warranty.

PTO LOCATION

The transmission shall have two (2) power take off (PTO) mounting locations, one (1) in the 8:00 o’clock position and one (1) in the 4:00 o’clock position.

DRIVELINE

All drivelines shall be heavy duty metal tube and equipped with Spicer 1710 series universal joints. The shafts shall be dynamically balanced prior to installation to alleviate future vibration. In areas of the driveline where a slip shaft is required, the splined slip joint shall be coated with Glide Coat ® .

MIDSHIP PUMP / GEARBOX

A temporary jackshaft driveline shall be installed by the chassis manufacturer to accommodate the mid-ship split shaft pump as specified by the apparatus manufacturer.

MIDSHIP PUMP / GEARBOX MODEL

The midship pump/gearbox provisions shall be for a Waterous CSUC20 pump.

MIDSHIP PUMP GEARBOX DROP

The Waterous pump gearbox shall have a “C” (medium length) drop length.

MIDSHIP PUMP RATIO

The ratio for the midship pump shall be 2.27:1.

MIDSHIP PUMP LOCATION C/L SUCTION TO C/L REAR AXLE

The midship pump shall be located so the dimension from the centerline of the suction to the centerline of the rear axle is 80.00 inches.

PUMP SHIFT CONTROLS

One (1) pump shift control panel shall be mounted on the driver’s dash panel. The following shall be provided on the panel: a three (3) position locking toggle switch; an engraved PUMP ENGAGED identification light; and an engraved OK TO PUMP identification light. The pump shift control panel shall be black with a yellow border outline. One (1) label indicating pump instructions and the transmission shift selector position used for pumping shall be provided and located so it can be read from the driver’s position per NFPA 16.10.1.3. The road mode shall be selected when the switch is in the up position and pump mode shall be selected when the switch is in the down position. The center switch position shall exhaust air from both pump and road sides of the pump gear box shift cylinder.

PUMP SHIFT CONTROL PLUMBING

Air connections shall be provided from the air supply tank to the pump shift control valve and from the pump shift control valve to the frame mounted bracket. The frame mounted bracket shall include labeling identifying the pump and road connection points with threaded 0.25 inch NPT fittings on the solenoid for attaching the customer installed pump. The air supply shall be pressure protected from service brake system.

FUEL FILTER/WATER SEPARATOR

The fuel system shall have a Fleetguard FS1003 fuel filter/water separator as a primary filter. The fuel filter shall have a drain valve. A water in fuel sensor shall be provided and wired to an instrument panel lamp and audible alarm to indicate when water is present in the fuel/water separator.

A secondary fuel filter shall be included as approved by the engine manufacturer .

FUEL LINES

The fuel system supply and return lines installed from the fuel tank to the engine shall be reinforced nylon tubing rated for diesel fuel. The fuel lines shall be brown in color and connected with brass fittings.

ELECTRIC FUEL PRIMER

Integral to the engine assembly is an electric lift pump that serves the purpose of pre-filter fuel priming.

FUEL TANK

The fuel tank shall have a capacity of fifty (50) gallons and shall measure 35.00 inches in width X 15.00 inches in height X 24.00 inches in length. The baffled tank shall be made of 14 gauge aluminized steel. The exterior of the tank shall be painted with a PRP Corsol™ black anti-corrosive exterior metal treatment finish. This results in a tank which offers the internal and external corrosion resistance. The tank shall have a vent port to facilitate venting to the top of the fill neck for rapid filling without "blow-back" and a roll over ball check vent for temperature related fuel expansion and draw. The tank is designed with dual draw tubes and sender flanges. The tank shall have 2.00 inch NPT fill ports for right or left hand fill. A 0.50 inch NPT drain plug shall be centered in the bottom of the tank. The fuel tank shall be mounted below the frame, behind the rear axle. Two (2) three-piece strap hanger assemblies with “U” straps bolted midway on the fuel tank front and rear shall be utilized to allow the tank to be easily lowered and removed for service purposes. Rubber isolating pads shall be provided between the tank and the upper tank mounting brackets. Strap mounting studs through the rail, hidden behind the body shall not be acceptable.

FUEL TANK MATERIAL AND FINISH

The fuel tank shall be constructed of 14 gauge aluminized steel. The exterior of the fuel tank shall be painted to match the frame color.

FUEL TANK STRAP MATERIAL

The fuel tank straps shall be constructed of ASTM A-36 steel.

FUEL TANK FILL PORT

The fuel tank fill ports shall be offset with the left fill port located in the rearward position and the right fill port located in the middle position on the fuel tank.

FUEL TANK DRAIN PLUG

A 0.5 inch NPT drain plug shall be centered in the bottom of the fuel tank.

FRONT AXLE

The front axle shall be a Meritor Easy Steer Non drive front axle, model number MFS-20. The axle shall include a 3.74 inch drop and a 71.00 inch king pin intersection (KPI). The axle shall include a conventional style hub with a standard knuckle.

FRONT AXLE WARRANTY

The front axle shall be warranted by Meritor for two (2) years with unlimited miles under the general service application. Details of the Meritor warranty are provided on the PDF document attached to this option.

FRONT WHEEL BEARING LUBRICATION

The front axle wheel bearings shall be lubricated with oil. The oil level can be visually checked via clear inspection windows in the front axle hubs.

FRONT SHOCK ABSORBERS

Two (2) Bilstein inert, nitrogen gas filled shock absorbers shall be provided and installed as part of the front suspension system. The shocks shall be a monotubular design and fabricated using a special extrusion method, utilizing a single blank of steel without a welded seam, achieving an extremely tight peak-to-valley tolerance and maintains consistent wall thickness. The monotubular design shall provide superior strength while maximizing heat dissipation and shock life. The ride afforded through the use of a gas shock is more consistent and shall not deteriorate with heat, the same way a conventional oil filled hydraulic shock would. The Bilstein front shocks shall include a digressive working piston assembly allowing independent tuning of the compression and rebound damping forces to provide optimum ride and comfort without compromise. The working piston design shall feature fewer parts than most conventional twin tube and “road sensing” shock designs and shall contribute to the durability and long life of the Bilstein shock absorbers. Proposals offering the use of conventional twin tube or “road sensing” designed shocks shall not be considered.

FRONT SUSPENSION

The front suspension shall include a nine (9) leaf spring pack in which the longest leaf measures 54.00 inch long and 4.00 inches wide and shall include a military double wrapped front eye. Both spring eyes shall have a case hardened threaded bushing installed with lubrication counter bore and lubrication land off cross bore with grease fitting. The spring capacity shall be rated at 21,500 pounds.

STEERING COLUMN/ WHEEL

The cab shall include a Douglas Autotech steering column which shall include a seven (7) position tilt, a 2.25 inch telescopic adjustment, and an 18.00 inch, four (4) spoke steering wheel located at the driver’s position. The steering wheel shall be covered with black polyurethane foam padding.

The steering column shall contain a horn button, self-canceling turn signal switch, four-way hazard switch and headlamp dimmer switch.

ELECTRONIC POWER STEERING FLUID LEVEL INDICATOR

The power steering fluid shall be monitored electronically and shall send a signal to activate an audible alarm and visual warning in the instrument panel when fluid level falls below normal.

POWER STEERING PUMP

The hydraulic power steering pump shall be a TRW PS and shall be gear driven from the engine. The pump shall be a balanced, positive displacement, sliding vane type.

FRONT AXLE CRAMP ANGLE

The chassis shall have a front axle cramp angle of 48-degrees to the left and 44-degrees to the right.

POWER STEERING GEAR

The power steering gear shall be a TRW model TAS 65 with an assist cylinder.

CHASSIS ALIGNMENT

The chassis frame rails shall be measured to insure the length is correct and cross checked to make sure they run parallel and are square to each other. The front and rear axles shall be laser aligned. The front tires and wheels shall be aligned and toe-in set on the front tires by the chassis manufacturer.

REAR AXLE

The rear axle shall be a Meritor model RS-25-160 single drive axle. The axle shall include precision forged, single reduction differential gearing, and shall have a fire service rated capacity of 27,000 pounds. The axle shall be built of superior construction and quality components to provide the rugged dependability needed to stand up to the fire industry’s demands. The axle shall include rectangular shaped, hot-formed housing with a standard wall thickness of 0.63 of an inch for extra strength and rigidity and a rigid differential case for high axle strength and reduced maintenance. The axle shall have heavy-duty Hypoid gearing for longer life, greater strength and quieter operation. Industry-standard wheel ends for compatibility with both disc and drum brakes, and unitized oil seal technology to keep lubricant in and help prevent contaminant damage will be used.

REAR AXLE DIFFERENTIAL LUBRICATION

The rear axle differential shall be lubricated with oil.

REAR AXLE WARRANTY

The rear axle shall be warranted by Meritor for two (2) years with unlimited miles under the general service application. Details of the Meritor warranty are provided on the PDF document attached to this option.

REAR WHEEL BEARING LUBRICATION

The rear axle wheel bearings shall be lubricated with oil.

VEHICLE TOP SPEED

The top speed of the vehicle shall be approximately 65 MPH +/-2 MPH at governed engine RPM.

REAR SUSPENSION

The single rear axle shall feature a Reyco 79KB vari-rate, self-leveling captive slipper type conventional multi-leaf spring suspension, with 57.50 inch X 3.00 inch springs. One (1) adjustable and one (1) fixed torque rod shall be provided. The rear suspension capacity shall be rated from 21,000 to 31,500 pounds.

FRONT TIRE

The front tires shall be Michelin 385/65R-22.5 18PR "J" tubeless radial XZY3 mixed service tread. The front tire stamped load capacity shall be 18,740 pounds per axle with a speed rating of 65 miles per hour when properly inflated to 120 pounds per square inch. The Michelin Tire Intermittent Service Rating load capacity shall be 20,000 pounds per axle with a speed rating of 65 miles per hour when properly inflated to 120 pounds per square inch. The Michelin Intermittent Service Rating limits the operation of the emergency vehicle to one (1) hour of loaded travel with a one (1) hour cool down prior to another loaded run.

REAR TIRE

The rear tires shall be Michelin 12R-22.5 16PR "H" tubeless radial XDN2 all-weather tread. The rear tire stamped load capacity shall be 27,120 pounds per axle with a speed rating of 75 miles per hour when properly inflated to 120 pounds per square inch. The Michelin Tire Intermittent Service Rating load capacity shall be 28,880 pounds per axle with a speed rating of 75 miles per hour when properly inflated to 120 pounds per square inch. The Michelin Intermittent Service Rating limits the operation of the emergency vehicle to one (1) hour of loaded travel with a one (1) hour cool down prior to another loaded run.

REAR AXLE RATIO

The rear axle ratio shall be 6.14:1.

TIRE PRESSURE INDICATOR

There shall be a voucher provided with the chassis for a pop up style tire pressure indicator at each tire valve stem. The indicator shall provide visual indication of pressure in the specific tire. The tire pressure indicators shall be redeemed upon the vehicle manufacturer’s receipt of the voucher for installation by the customer.

FRONT WHEEL

The front wheels shall be Alcoa hub piloted, 22.50 inch X 12.25 inch LvL One™ polished aluminum wheels. The hub piloted mounting system shall provide easy installation and shall include two-piece flange nuts. The wheels shall feature one-piece forged strength and shall include Alcoa’s Dura-Bright ® finish with XBR technology as an integral part of the wheel surface. Alcoa Dura-Bright ® wheels keep their shine without polishing. Brake dust, grime and road debris are easily removed by simply cleaning the wheels with soap and water.

REAR WHEEL

The rear wheels shall be Alcoa hub piloted, 22.50 inch X 8.25 inch LvL One™ aluminum wheels with a polished outer surface and Alcoa Dura-Bright® wheel treatment with XBR® technology as an integral part of the wheel. The hub piloted mounting system shall provide easy installation and shall include two-piece flange nuts.

WHEEL TRIM

The front wheels shall include stainless steel lug nut covers and stainless steel baby moons shipped loose with the chassis for installation by the apparatus builder. The baby moons shall have cutouts for oil seal viewing when applicable. The rear wheels shall include stainless steel lug nut covers and band mounted spring clip stainless steel high hats shipped loose with the chassis for installation by the apparatus builder. The lug nut covers, baby moons, and high hats shall be RealWheels ® brand constructed of 304L grade, non-corrosive stainless steel with a mirror finish. Each wheel trim component shall meet D.O.T. certification.

BRAKE SYSTEM

A rapid build-up air brake system shall be provided. The air brakes shall include a two (2) air tank, three (3) reservoir system with a total of 4152 cubic inch of air capacity. A floor mounted treadle valve shall be mounted inside the cab for graduated control of applying and releasing the brakes. An inversion valve shall be installed to provide a service brake application in the unlikely event of primary air supply loss. All air reservoirs provided on the chassis shall be labeled for identification. The rear axle spring brakes shall automatically apply in any situation when the air pressure falls below 25 PSI and shall include a mechanical means for releasing the spring brakes when necessary. An audible alarm shall designate when the system air pressure is below 60 PSI.

A four (4) sensor, four (4) modulator anti-lock braking system (ABS) shall be installed on the front and rear axles in order to prevent the brakes from locking or skidding while braking during hard stops or on icy or wet surfaces. This in turn shall allow the driver to maintain steering control under heavy braking and in most instances, shorten the braking distance. The electronic monitoring system shall incorporate diagonal circuitry which shall monitor wheel speed during braking through a sensor and tone ring on each wheel. A dash mounted ABS lamp shall be provided to notify the driver of a system malfunction. The ABS system shall automatically disengage the auxiliary braking system device when required. The speedometer screen shall be capable of reporting all active defaults using PID/SID and FMI standards. Additional safety shall be accommodated through Automatic Traction Control (ATC) which shall be installed on the single rear axle. The ATC system shall apply the ABS when the drive wheels loose traction. The system shall scale the electronic engine throttle back to prevent wheel spin while accelerating on ice or wet surfaces. A momentary rocker style switch shall be provided and properly labeled “mud/snow”. When the switch is pressed once, the system shall allow a momentary wheel slip to obtain traction under extreme mud and snow conditions. During this condition the ATC light and the light on the rocker switch shall blink continuously notifying the driver of activation. Pressing the switch again shall deactivate the mud/snow feature. The Electronic Stability Control (ESC) unit is a functional extension of the electronic braking system. It is able to detect any skidding of the vehicle about its vertical axis as well as any rollover tendency. The control unit comprises an angular-speed sensor that measures the vehicle’s motion about the vertical axis, caused, for instance, by cornering or by skidding on a slippery road surface. An acceleration sensor measures the vehicle’s lateral acceleration. The Controller Area Network (CAN) bus provides information on the steering angle. On the basis of lateral acceleration and steering angle, an integrated microcontroller calculates a theoretical angular speed for the stable vehicle condition .

FRONT BRAKES

The front brakes shall be Meritor 16.50 inch x 6.00 inch S-cam drum type.

REAR BRAKES

The rear brakes shall be Meritor 16.50 inch X 7.00 inch S-cam drum type. The brakes shall feature a cast iron shoe.

PARK BRAKE

Upon application of the push-pull valve in the cab, the rear brakes will engage via mechanical spring force. This is accomplished by dual chamber rear brakes, satisfying the FMVSS parking brake requirements.

PARK BRAKE CONTROL

A Meritor-Wabco manual hand control push-pull style valve shall operate the parking brake system. The control shall be yellow in color.

The parking brake actuation valve shall be mounted on the center of the tunnel within easy access of both the driver and officer positions.

FRONT BRAKE SLACK ADJUSTERS

The front brakes shall include Meritor automatic slack adjusters installed on the chassis which features a simple, durable design offering reduced weight. The automatic slack adjusters shall feature a manual adjusting nut which cannot inadvertently be backed off and threaded grease fittings for easy serviceability.

REAR BRAKE SLACK ADJUSTERS

The rear brakes shall include Meritor automatic slack adjusters installed on the axle which features a simple, durable design offering reduced weight. The automatic slack adjusters shall feature a manual adjusting nut which cannot inadvertently be backed off and threaded grease fittings for easy serviceability.

AIR DRYER

The brake system shall include a Wabco System Saver 1200 air dryer with an integral heater with a Metri-Pack sealed connector. The air dryer incorporates an internal turbo cutoff valve that closes the path between the air compressor and air dryer purge valve during the compressor "unload" cycle. The turbo cutoff valve allows purging of moisture and contaminants without the loss of turbo boost pressure. The air dryer shall be mounted behind the battery box on the left hand side.

FRONT BRAKE CHAMBERS

The front brakes shall be provided with MGM type 30 brake chambers.

REAR BRAKE CHAMBERS

The rear axle shall include TSE 30/36 brake chambers which shall convert the energy of compressed air into mechanical force and motion. This shall actuate the brake camshaft, which in turn shall operate the foundational brake mechanism forcing the brake shoes against the brake drum. The TSE Type 36 brake chamber has a 36.00 square inch effective area.

AIR COMPRESSOR

The air compressor provided for the engine shall be a Wabco ® SS318 single cylinder pass-through drive type compressor which shall be capable of producing 18.7 CFM at 1200 engine RPMs. The air compressor shall feature a higher delivery efficiency translating to more air delivery per horsepower absorbed. The compressor shall include an aluminum cylinder head which shall improve cooling, reduce weight and decrease carbon formation. Superior piston and bore finishing technology shall reduce oil consumption and significantly increasing the system component life.

AIR GOVERNOR

An air governor shall be provided to control the cut-in and cut-out pressures of the engine mounted air compressor. The governor shall be calibrated to meet FMVSS requirements. The air governor shall be located on the air dryer bracket on the left frame rail behind the battery box.

MOISTURE EJECTORS

Manual pet-cock type drain valves shall be installed on all reservoirs of the air supply system.

AIR SUPPLY LINES

The air system on the chassis shall be plumbed with color coded reinforced nylon tubing air lines. The primary (rear) brake line shall be green, the secondary (front) brake line red, the parking brake line orange and the auxiliary (outlet) will be blue. Brass compression type fittings shall be used on the nylon tubing. All drop hoses shall include fiber reinforced neoprene covered hoses.

AIR INLET CONNECTION

An air connection for the shoreline air inlet shall be supplied.

AIR INLET LOCATION

The air inlet shall be installed in the left hand side lower front step in the forward position.

PLUMBING AIR INLET CONNECTION

The air inlet connector shall be plumbed to the air system with a check valve to prevent air from escaping through the inlet connector.

AIR INLET/ OUTLET FITTING TYPE

The air connector supplied shall be a 0.25 inch size Tru-Flate Interchange style manual connection which is compatible with Milton ‘T’ style, Myers 0.25 inch Automotive style and Parker 0.25 inch 10 Series connectors.

REAR AIR TANK MOUNTING

If a combination of wheel base, air tank quantity, or other requirements necessitate the location of one or more air tanks to be mounted rear of the fuel tank, these tank(s) will be mounted perpendicular to frame.

WHEELBASE

The chassis wheelbase shall be 193.00 inches.

REAR OVERHANG

The chassis rear overhang shall be 37.00 inches.

FRAME

The frame shall consist of double rails running parallel to each other with cross members forming a ladder style frame. The frame rails shall be formed in the shape of a "C" channel, with the outer rail measuring 10.25 inches high X 3.50 inches deep upper and lower flanges X 0.38 inches thick with an inner channel of 9.44 inches high X 3.13 inches deep and 0.38 inches thick. Each rail shall be constructed of 110,000 psi minimum yield high strength low alloy steel. Each double rail section shall be rated by a Resistance Bending Moment (RBM) minimum of 3,213,100 inch pounds and have a minimum section modulus of 29.21 cubic inches. The frame shall measure 35.00 inches in width. Proposals calculating the frame strength using the “box method” shall not be considered. Proposals including heat treated rails shall not be considered. Heat treating frame rails produces rails that are not uniform in their mechanical properties throughout the length of the rail. Rails made of high strength, low alloy steel are already at the required yield strength prior to forming the rail. A minimum of seven (7) fully gusseted 0.25 inch thick cross members shall be installed. The inclusion of the body mounting, or bumper mounting shall not be considered as a cross member. The cross members shall be attached using zinc coated grade 8 fasteners. The bolt heads shall be flanged type, held in place by distorted thread flanged lock nuts. Each cross member shall be mounted to the frame rails utilizing a minimum of 0.25 inch thick gusset reinforcement plates at all corners balancing the area of force throughout the entire frame. . Any proposals not including additional reinforcement for each cross member shall not be considered. All relief areas shall be cut in with a minimum 2.00 inch radius at intersection points with the edges ground to a smooth finish to prevent a stress concentration point. The frame and cross members shall carry a lifetime warranty to the original purchaser. A copy of the frame warranty shall be made available upon request. Proposals offering warranties for frames not including cross members shall not be considered.

FRAME WARRANTY

Summary of Warranty Terms: THE FOLLOWING IS SUMMARY OF WARRANTY TERMS FOR INFORMATION ONLY. THE ACTUAL LIMITED WARRANTY DOCUMENT, WHICH IS ATTACHED TO THIS OPTION, CONTAINS THE COMPLETE STATEMENT OF THE SPARTAN MOTORS USA LIMITED WARRANTY. SPARTAN’S RESPONSIBILITY IS TO BE ACCORDING TO THE TERMS OF THE COMPLETE LIMITED WARRANTY DOCUMENT. The frame and cross members shall carry a limited lifetime warranty to the original purchaser. The warranty period shall commence on the date the vehicle is delivered to the first end user.

FRAME CLEAR AREA

The chassis frame shall be left clear of chassis mounted components inside or outside the frame rails within the first 30.00 inches behind the cab to allow space for OEM installed components. Cross members may be installed in the clear area if required for proper frame or driveline configuration.

FRAME PAINT

The frame shall be powder coated black prior to any attachment of components. All powder coatings, primers and paint shall be compatible with all metals, pretreatments and primers used. The cross hatch adhesion test per ASTM D3359 shall not have a fail of more than ten (10) squares. The pencil hardness test per ASTM D3363 shall have a final post-curved pencil hardness of H-2H. The direct impact resistance test per ASTM D2794 shall have an impact resistance of 120.00 inches per pound at 2 mils. Any proposals offering painted frame with variations from the above process shall not be accepted. The film thickness of vendor supplied parts shall also be sufficient to meet the performance standards as stated above.

FRONT BUMPER

A one piece, two (2) rib wrap-around style, polished stainless steel front bumper shall be provided. The material shall be 10 gauge 304 stainless steel, 12.00 inches high and 99.00 inches wide.

FRONT BUMPER EXTENSION LENGTH

The front bumper shall be extended approximately 24.00 inches ahead of the cab.

FRONT BUMPER EXTENSION FRAME WIDTH

The front bumper extension frame shall feature an overall width of 48.25 inches.

FRONT BUMPER APRON

The 24.00 inch extended front bumper shall include an apron constructed of 0.19 inch thick embossed aluminum tread plate. The apron shall be installed between the bumper and the front face of the cab affixed using stainless steel bolts attaching the apron to the top bumper flange.

FRONT BUMPER COMPARTMENT CENTER

The front bumper shall include a compartment in the bumper apron located in the center between the frame rails which may be used as a hose well. The compartment shall be constructed of 0.13 inch 5052-H32 grade aluminum and shall include drain holes in the bottom corners to allow excess moisture to escape. The compartment shall include a cover constructed of 0.19 inch thick bright embossed aluminum tread plate.

FRONT BUMPER COMPARTMENT COVER HARDWARE

The front bumper compartment cover(s) shall include gas cylinder stays which shall hold the cover open. Each cover shall be held in the closed position via a D-ring style latch.

MECHANICAL SIREN

The front bumper shall include an electro mechanical Federal Q2B™ siren, which shall be streamlined, chrome-plated and shall produce 123 decibels of sound at 10.00 feet. The Q2B™ siren produces a distinctive warning sound that is recognizable at long distances. A unique clutch design provides a longer coast down sound while reducing the amp draw to 100 amps. The siren shall measure 10.50 inches wide X 10.00 inches high X 14.00 inches deep. The siren shall include a pedestal mount to surface mount on a horizontal surface.

MECHANICAL SIREN LOCATION

The siren shall be pedestal mounted on the bumper apron on the furthest outboard section of the bumper on the driver side.

AIR HORN

The chassis shall include two (2) Hadley brand E-Tone air horns which shall measure 24.00 inches long with a 6.00 inch round flare. The air horns shall be trumpet style with a chrome finish on the exterior and a painted finish deep inside the trumpet.

AIR HORN LOCATION

The air horns shall be recess mounted in the front bumper face, one (1) on the right side of the bumper in the inboard position relative to the right hand frame rail and one (1) on the left side of the bumper in the inboard position relative to the left hand frame rail.

AIR HORN RESERVOIR

One (1) air reservoir, with a 1200 cubic inch capacity, shall be installed on the chassis to act as a supply tank for operating air horns. The reservoir shall be isolated with a 90 PSI pressure protection valve on the reservoir supply side to prevent depletion of the air to the air brake system.

ELECTRONIC SIREN SPEAKER

There shall be one (1) Cast Products Inc. model SA4301, 100 watt speaker provided. The speaker shall measure 6.20 inches tall X 7.36 inches wide X 3.06 inches deep. The speaker shall include a flat mounting flange which shall be polished aluminum.

ELECTRONIC SIREN SPEAKER LOCATION

The electronic siren speaker shall be located on the front bumper face in the center position between the frame rails.

FRONT BUMPER TOW HOOKS

Two (2) heavy duty tow hooks, painted to match the chassis frame, shall be installed in a rearward position out of the approach angle area, bolted directly to the side of the chassis frame with grade 8 bolts.

CAB TILT SYSTEM

The entire cab shall be capable of tilting approximately 45-degrees to allow for easy maintenance of the engine and transmission. The cab tilt pump assembly shall be located on the right side of the chassis above the battery box. The electric-over-hydraulic lift system shall include an ignition interlock and red cab lock down indicator lamp on the tilt control which shall illuminate when holding the “Down” button to indicate safe road operation. It shall be necessary to activate the master battery switch and set the parking brake in order to tilt the cab. As a third precaution the ignition switch must be turned off to complete the cab tilt interlock safety circuit. Two (2) spring-loaded hydraulic hold down hooks located outboard of the frame shall be installed to hold the cab securely to the frame. Once the hold-down hooks are set in place, it shall take the application of pressure from the hydraulic cab tilt lift pump to release the hooks. Two (2) cab tilt cylinders shall be provided with velocity fuses in each cylinder port. The cab tilt pivots shall be 1.90 inch ball and be anchored to frame brackets with 1.25 inch diameter studs. A steel safety channel assembly, painted safety yellow shall be installed on the right side cab lift cylinder to prevent accidental cab lowering. The safety channel assembly shall fall over the lift cylinder when the cab is in the fully tilted position. A cable release system shall also be provided to retract the safety channel assembly from the lift cylinder to allow the lowering of the cab.

CAB TILT CONTROL RECEPTACLE

The cab tilt control cable shall include a receptacle which shall be temporarily located on the right hand chassis rail rear of the cab to provide a place to plug in the cab tilt remote control pendant. The tilt pump shall include 8.00 feet of cable with a six (6) pin Deutsch receptacle with a cap. The remote control pendant shall include 20.00 feet of cable with a mating Deutsch connector. The remote control pendant shall be shipped loose with the chassis.

CAB WINDSHIELD

The cab windshield shall have a surface area of 2825.00 square inches and be of a two (2) piece wraparound design for maximum visibility. The glass utilized for the windshield shall include standard automotive tint. The left and right windshield shall be fully interchangeable thereby minimizing stocking and replacement costs. Each windshield shall be installed using black self locking window rubber.

GLASS FRONT DOOR

The front cab doors shall include a window which is 27.00 inches in width X 26.00 inches in height. These windows shall have the capability to roll down completely into the door housing. This shall be accomplished manually utilizing a crank style handle on the inside of the door. A reinforced window regulator assembly shall be provided for severe duty use. There shall be an irregular shaped fixed window which shall measure 2.50 inches wide at the top, 8.00 inches wide at the bottom X 26.00 inches in height, more commonly known as “cozy glass” ahead of the front door roll down windows. The windows shall be mounted within the frame of the front doors trimmed with a black anodized ring on the exterior.

GLASS TINT FRONT DOOR

The windows located in the left and right front doors shall have a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance.

GLASS REAR DOOR RH

The rear right hand side door shall include a window which is 27.00 inches in width X 26.00 inches in height. This window shall roll up and down manually utilizing a crank style handle on the inside of the door. A reinforced window regulator assembly shall be provided for severe duty use.

GLASS TINT REAR DOOR RIGHT HAND

The window located in the right hand side rear door shall include a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance.

GLASS REAR DOOR LH

The rear left hand side door shall include a window which is 27.00 inches in width X 26.00 inches in height. This window shall roll up and down manually utilizing a crank style handle on the inside of the door. A reinforced window regulator assembly shall be provided for severe duty use.

GLASS TINT REAR DOOR LEFT HAND

The window located in the left hand side rear door shall include a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance.

GLASS SIDE MID RH

The cab shall include a window on the right side behind the front and ahead of the crew door which shall measure 16.00 inches wide X 26.00 inches high. This window shall be fixed within this space and shall be rectangular in shape. The window shall be mounted using self locking window rubber. The glass utilized for this window shall include a green automotive tint unless otherwise noted.

GLASS TINT SIDE MID RIGHT HAND

The window located on the right hand side of the cab between the front and rear doors shall include a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance.

GLASS SIDE MID LH

The cab shall include a window on the left side behind the front door and ahead of the crew door and above the wheel well which shall measure 16.00 inches wide X 26.00 inches high. This window shall be fixed within this space and shall be rectangular in shape. The window shall be mounted using self locking window rubber. The glass utilized for this window shall include a green automotive tint unless otherwise noted.

GLASS TINT SIDE MID LEFT HAND

The window located on the left hand side of the cab between the front and rear doors shall include a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance.

CLIMATE CONTROL

A ceiling mounted combination defroster and cabin heating and air conditioning system shall be located above the engine tunnel area. The system covers and plenums shall be of sever duty design made of aluminum which shall be coated with a customer specified interior paint. The design of the system’s covers shall provide quick access to washable air intake filters as well as easy access to other serviceable items. The air delivery plenums provide targeted airflow directly to the vehicle occupants. Six (6) adjustable louvers will provide comfort for the front seat occupants and ten (10) adjustable louvers will provide comfort for the rear crew occupants. The system shall be capable of producing up to 12 FPM of air velocity at all occupant seating positions. Separate front and rear blower motors shall be of brushless design and shall be controlled independently. It shall be capable of reducing the interior cabin air temperature from 122 ˚ F (+/- 3˚ F) to 80˚ F in thirty minutes with 50% relative humidity and full solar load as described in SAE J2646. The system shall also provide heater pull up performance which meets or exceeds the performance requirements of SAE J1612 as well as defrost performance that meets or exceeds the performance requirements of SAE J381. A gravity drain system shall be provided that is capable of evacuating condensate from the vehicle while on a slope of up to a 13% grade in any direction. The air conditioning system plumbing shall be a mixture of custom bent zinc coated steel fittings and Aero-quip GH134 flexible hose with Aeroquip EZ-Clip fittings. The overhead heater/defroster plumbing shall include an electronic flow control valve that re-directs hot coolant away from the evaporator, via a bypass loop, as the temperature control is moved toward the cold position.

Any component which needs to be accessed to perform system troubleshooting shall be accessible by one person using basic hand tools. Regularly serviced items shall be replaceable by one person using basic hand tools.

**Performance data is based on testing performed by an independent third party test facility using a

medium four-door 10” Raised roof Gladiator chassis equipped with an ISL engine. CLIMATE CONTROL DRAIN

The climate control system shall include a gravity drain for water management. The gravity drain shall remove condensation from the air conditioning system without additional mechanical assistance.

CLIMATE CONTROL ACTIVATION

The heating, defrosting and air conditioning controls shall be on the dash next to driver panel, in a position which is easily accessible to the driver. The climate control shall be activated by a rotary switch.

HVAC OVERHEAD COVER PAINT

The overhead HVAC cover shall be painted with a multi-tone silver gray texture finish.

A/C CONDENSER LOCATION

A roof mounted A/C condenser shall be installed centered on the cab forward of the raised roof against the slope rise.

A/C COMPRESSOR

The air-conditioning compressor shall be a belt driven, engine mounted compressor. The compressor shall be compatible with R134-a refrigerant.

UNDER CAB INSULATION

The underside of the cab tunnel surrounding the engine shall be lined with multi-layer insulation, engineered for application inside diesel engine compartments. The insulation shall act as a noise barrier, absorbing noise thus keeping the decibel level in the cab well within NFPA recommendations. As an additional benefit, the insulation shall assist in sustaining the desired temperature within the cab interior. The engine tunnel insulation shall measure approximately 0.75 inch thick including a vertically lapped polyester fiber layer, a 1.0 lb/ft² PVC barrier layer, an open cell foam layer, and a moisture and heat reflective foil facing reinforced with a woven fiberglass layer. The foil surface acts as protection against moisture and other contaminants. The insulation shall meet or exceed FMVSS 302 flammability test. The insulation shall be cut precisely to fit each section and sealed for additional heat and sound deflection. The insulation shall be held in place by 3 mils of acrylic pressure sensitive adhesive and aluminum pins with hard hat, hold in place fastening heads.

INTERIOR TRIM FLOOR

The floor of the cab shall be covered with a multi-layer mat consisting of 0.25 inch thick sound absorbing closed cell foam with a 0.06 inch thick non-slip vinyl surface with a pebble grain finish. The covering shall be held in place by a pressure sensitive adhesive and aluminum trim molding. All exposed seams shall be sealed with silicone caulk matching the color of the floor mat to reduce the chance of moisture and debris retention.

INTERIOR TRIM

The cab interior shall include trim on the front ceiling, rear crew ceiling, and the cab walls. It shall be easily removable to assist in maintenance. The trim shall be constructed of insulated vinyl over a hard board backing.

REAR WALL INTERIOR TRIM

The rear wall of the cab shall be trimmed with vinyl.

HEADER TRIM

The cab interior shall feature header trim over the driver and officer dash constructed of 5052-H32 Marine Grade, 0.13 inch thick aluminum.

TRIM CENTER DASH

The main center dash area shall be constructed of 5052-H32 Marine Grade, 0.13 inch thick aluminum plate. There shall be four (4) holes located on the top of the dash near each outer edge of the electrical access cover for ventilation. The dash shall include cup holders and storage bins.

TRIM LH DASH

The left hand dash shall be constructed of 5052-H32 Marine Grade, 0.13 inch thick aluminum plate for a perfect fit around the instrument panel. For increased occupant protection the extreme duty left hand dash utilizes patent pending break away technology to reduce rigidity in the event of a frontal crash. The left hand dash shall offer lower vertical surface area to the left and right of the steering column to accommodate control panels.

TRIM RH DASH

The right hand dash shall be constructed of 5052-H32 Marine Grade, 0.13 of an inch thick aluminum plate and shall include a glove compartment with a hinged door and a Mobile Data Terminal (MDT) provision. The glove compartment size will measure 14.00 inches wide X 6.38 inches high X 5.88 inches deep. The MDT provision shall be provided above the glove compartment.

ENGINE TUNNEL TRIM

The cab engine tunnel shall be covered with a multi-layer mat consisting of 0.25 inch closed cell foam with a 0.06 inch thick non-slip vinyl surface with a pebble grain finish. The mat shall be held in place by

pressure sensitive adhesive. The engine tunnel mat shall be trimmed with anodized aluminum stair nosing trim for an aesthetically pleasing appearance.

POWER POINT DASH MOUNT

The cab shall include one (1) 12 volt cigarette lighter type receptacle in the cab dash to provide a power source for 12 volt electrical equipment. The cab shall also include two (2) universal serial bus (USB) charging receptacles in the cab dash to provide a power source for USB chargeable electrical equipment. Each USB port shall be capable of a 5 Volt-500 milliampere output. The receptacles shall be wired battery direct.

STEP TRIM

Each cab entry door shall include a three step entry. The first step closest to the ground shall be constructed of polished 5032 H32 aluminum Grip Strut® grating with angled outer corners. The step shall feature a splash guard to reduce water and debris from splashing in to the step. The splash guard shall have an opening on the outer edge to allow debris and water to flow through rather than becoming trapped within the stepping surface. The lower step shall be mounted to a frame which is integral with the construction of the cab for rigidity and strength. The middle step shall be integral with the cab construction and shall be trimmed with a Flex-Tred ® adhesive grit surface material.

UNDER CAB ACCESS DOOR

The cab shall include an aluminum access door in the left crew step riser painted to match the cab interior paint with a push and turn latch. The under cab access door shall provide access to the diesel exhaust fluid fill.

INTERIOR DOOR TRIM

The interior trim on the doors of the cab shall consist of an aluminum panel constructed of Marine Grade 5052-H32 0.13 of an inch thick aluminum plate. The door panels shall include a painted finish.

DOOR TRIM CUSTOMER NAMEPLATE

The interior door trim on the front doors shall include a customer nameplate which states the vehicle was custom built for their Department.

CAB DOOR TRIM REFLECTIVE

The interior of each door shall include high visibility reflective tape. A white reflective tape shall be provided vertically along the outer rear edge of the door. The lowest portion of each door skin shall include solid white reflective tape. The tape shall measure 6.00 inches in height.

INTERIOR GRAB HANDLE "A" PILLAR

There shall be two (2) rubber covered 11.00 inch grab handles installed inside the cab, one on each “A” post at the left and right door openings. The left handle shall be located 7.88 inches above the bottom of the door window opening and the right handle shall be located 2.88 inches above the bottom of the door window opening. The handles shall assist personnel in entering and exiting the cab.

INTERIOR GRAB HANDLE FRONT DOOR

Each front door shall include one (1) ergonomically contoured 9.00 inch cast aluminum handle mounted horizontally on the interior door panels. The handles shall feature a textured black powder coat finish to assist personnel entering and exiting the cab.

INTERIOR GRAB HANDLE REAR DOOR

A black powder coated cast aluminum assist handle shall be provided on the inside of each rear crew door. A 30.00 inch long handle shall extend horizontally the width of the window just above the window sill. The handle shall assist personnel in exiting and entering the cab.

INTERIOR SOFT TRIM COLOR

The cab interior soft trim surfaces shall be gray in color.

INTERIOR TRIM SUNVISOR

The header shall include two (2) sun visors, one each side forward of the driver and officer seating positions above the windshield. Each sun visor shall be constructed of Masonite and covered with padded vinyl trim.

INTERIOR FLOOR MAT COLOR

The cab interior floor mat shall be gray in color.

CAB PAINT INTERIOR DOOR TRIM

The inner door panel surfaces shall be painted with multi-tone silver gray texture finish.

HEADER TRIM INTERIOR PAINT

The metal surfaces in the header area shall be coated with multi-tone silver gray texture finish.

TRIM CENTER DASH INTERIOR PAINT

The entire center dash shall be coated with multi-tone silver gray texture finish. Any accessory pods attached to the dash shall also be painted this color.

TRIM LH DASH INTERIOR PAINT

The left hand dash shall be painted with a multi-tone silver gray texture finish.

TRIM RIGHT HAND DASH INTERIOR PAINT

The right hand dash shall be painted with multi-tone silver gray texture finish.

DASH PANEL GROUP

The main center dash area shall include three (3) removable panels located one (1) to the right of the driver position, one (1) in the center of the dash and one (1) to the left of the officer position. The center panel shall be within comfortable reach of both the driver and officer.

SWITCHES CENTER PANEL

The center dash panel shall include eighteen (18) rocker switch positions in a twelve (12) over six (6) configuration in the left portion of the panel. A rocker switch with a blank legend installed directly above shall be provided for any position without a switch and legend designated by a specific option. The non-specified switches shall be two-position, black switches with a green indicator light. Each blank switch legend can be custom engraved by the body manufacturer. All switch legends shall have backlighting provided.

SWITCHES LEFT PANEL

The left dash panel shall include eight (8) switches in a single row configuration. Five (5) of the switches shall be rocker type and the left three (3) shall be the headlight switch, the instrument lamp dimmer switch and the windshield wiper/washer control switch. A rocker switch with a blank legend installed directly above shall be provided for any position not designated by a specific option. The non-designated switches shall be two-position, black switches with a green indicator light. Each blank switch legend can be custom engraved by the body manufacturer. All switch legends shall have backlighting provided.

SWITCHES RIGHT PANEL

The right dash panel shall include no rocker switches or legends.

SEAT BELT WARNING

A Weldon seat belt warning system, integrated with the Vehicle Data Recorder system, shall be installed for each seat within the cab. The system shall activate an indicator light in the instrument panel, a digital seat position indicator with a seat position legend in the switch panel, and an audible alarm. The warning system shall activate when any seat is occupied with a minimum of 60 pounds and the corresponding seat belt remains unfastened. The warning system shall also activate when any seat is occupied and the corresponding seat belt was fastened in an incorrect sequence. Once activated, the visual indicators and audible alarm shall remain active until all occupied seats have the seat belts fastened.

SEAT MATERIAL

The seats shall include a covering of high strength, wear resistant fabric made of durable ballistic polyester. A PVC coating shall be bonded to the back side of the material to help protect the seats from UV rays and from being saturated or contaminated by fluids. Common trade names for this material are Imperial 1200 and Durawear.

SEAT COLOR

All seats supplied with the chassis shall be gray in color. All seats shall include red seat belts.

SEAT BACK LOGO

The seat back shall include the “Smeal Fire Apparatus Co.” logo. The logo shall be centered on the standard headrest of the seat back and on the left side of a split headrest.

SEAT DRIVER

The driver's seat shall be an H.O. Bostrom Firefighter model seat. The seat shall feature two-way manual fore and aft adjustment with 5.00 inches of travel. The seat shall also feature integral springs to isolate shock. The seat shall feature an all belts to seat (ABTS) safety restraint system. The ABTS feature shall include a three-point shoulder harness with the lap belt, automatic retractor and buckle as an integral part of the seat assembly. The buckle portion of the seat belt shall be mounted on a semi-rigid stalk extending from the seat base within easy reach of the occupant. The minimum vertical dimension from the seat H-point to the ceiling for this belted seating position shall be 35.00 inches. This model of seat shall have successfully completed the static load tests set forth by FMVSS 207, 209, and 210 in effect at the time of manufacture. This testing shall include a simultaneous forward load of 3000 pounds each on the lap and shoulder belts and twenty (20) times the weight through the center of gravity. The materials used in construction of the seat shall also have successfully completed testing with regard to the flammability of materials used in the occupant compartments of motor vehicles as outlined in FMVSS 302, of which dictates the allowable burning rate of materials in the occupant compartments of motor vehicles.

SEAT BACK DRIVER

The driver’s seat shall include a standard seat back incorporating the all belts to seat feature (ABTS). The seat back shall feature a contoured head rest.

SEAT MOUNTING DRIVER

The driver’s seat shall be installed in an ergonomic position in relation to the cab dash.

OCCUPANT PROTECTION DRIVER

The driver’s position shall be equipped with the Advanced Protection System™ (APS). The APS shall selectively deploy integrated systems to protect against injuries in qualifying frontal impact, side impact, and rollover events. The increase in survivable space and security of the APS shall also provide ejection mitigation protection.

The driver’s seating area APS shall include: • Advanced seat belt system - retractor pre-tensioner tightens the seat belt around the driver, securing the occupant in the seat and the load limiter plays out some of the seat belt webbing to reduce seat belt to chest and torso force upon impact as well as mitigate head and neck injuries. • Large side curtain airbag - protects the driver’s head, neck, and upper body from dangerous cab side surfaces and contact points with intrusive surfaces as a result of a collision as well as provides ejection mitigation protection to the driver in a qualifying event by covering the window and the upper portion of the door. • Dual knee airbags (patent pending) with energy management mounting (patent pending) - protects the driver's lower body from dangerous surface contact injuries, acceleration injuries, and from intrusion as well as locks the lower body in place so the upper body shall be shall be slowed by the load limiting seat belt. Steering wheel airbag - protects the driver’s head, neck, and upper torso from contact injuries, acceleration injuries, and contact points with intrusive surfaces as a result of a collision.

SEAT OFFICER

The officer's seat shall be a H.O. Bostrom Firefighter series. The seat shall feature a tapered and padded seat, and cushion. The seat shall be a non-adjustable type seat. The seat shall feature an all belts to seat (ABTS) style of safety restraint. The ABTS feature shall include a three-point shoulder harness with the lap belt and automatic retractor as an integral part of the seat assembly. The buckle portion of the seat belt shall extend from the seat base towards the driver position within easy reach of the occupant. The minimum vertical dimension from the seat H-point to the ceiling for this belted seating position shall be 35.00 inches. This model of seat shall have successfully completed the static load tests by FMVSS 207/210. This testing shall include a simultaneous forward load of 3000 pounds each on the lap and shoulder belts and twenty (20) times the weight through the center of gravity. This model of seat installed in the cab model, as specified, shall have successfully completed the dynamic sled testing using FMVSS 208 as a guide with the following accommodations. In order to reflect the larger size outfitted firefighters, the test dummy used shall be a 95th percentile hybrid III male weighing 225 pounds rather than the 50th percentile male dummy weighing 165 pounds as referenced in FMVSS 208. The model of seats shall also have successfully completed the flammability of materials used in the occupant compartments of motor vehicles as outlined in FMVSS 302, of which decides the burning rate of materials in the occupant compartments of motor vehicles.

SEAT BACK OFFICER

The officer seat back shall include a Ziamatic brand model QM-EZL-F mechanical self-contained breathing apparatus (SCBA) bracket. The Mechanical walk away bracket shall meet NFPA 1901-09 9G dynamic requirements for cylinder restraint systems for use in crew compartments of fire truck cabs.

The bracket shall secure a self-contained breathing apparatus with most sizes of cylinders. The bracket shall feature a top clamp and a footplate which securely lock the SCBA. The top clamp shall be PVC coated to prevent damage to the cylinder. The steel back plate and cast aluminum footplate shall be powder coated. The bracket shall also include a pull release cable with a handle which activates the lever on the bracket saving the occupant from reaching behind the SCBA in order to release the bracket. The handle shall be located on the front of the seat in the center. The seat back shall include a removable padded cover which shall be provided over the SCBA cavity.

SEAT MOUNTING OFFICER

The officer’s seat shall be installed in an ergonomic position in relation to the cab dash.

OCCUPANT PROTECTION OFFICER

The officer’s position shall be equipped with the Advanced Protection System™ (APS). The APS shall selectively deploy integrated systems to protect against injuries in qualifying frontal impact, side impact, and rollover events. The increase in survivable space and security of the APS shall also provide ejection mitigation protection. The officer’s seating area APS shall include: • Advanced seat belt system - retractor pre-tensioner tightens the seat belt around the officer, securing the occupant in the seat and the load limiter plays out some of the seat belt webbing to reduce seat belt to chest and torso force upon impact as well as mitigate head and neck injuries. • Large side curtain airbag - protects the officer’s head, neck, and upper body from dangerous cab side surfaces and contact points with intrusive surfaces as a result of a collision as well as provides ejection mitigation protection to the officer in a qualifying event by covering the window and the upper portion of the door. Knee airbags - protects the officer's lower body from dangerous surface contact injuries, acceleration injuries, and from contact points with intrusive surfaces as a result of a collision as well as locks the lower body in place so the upper body shall be slowed by the load limiting seat belt.

SEAT BELT ORIENTATION CREW

The crew position seat belts shall follow the standard orientation which extends from the outboard shoulder extending to the inboard hip.

SEAT REAR FACING OUTER LOCATION

The crew area shall include two (2) rear facing crew seats, which include one (1) located directly behind the left side front seat and one (1) located directly behind the right side front seat.

SEAT CREW REAR FACING OUTER

The crew area shall include a seat in the rear facing outboard position which shall be a H.O. Bostrom Firefighter series. The seat shall feature a tapered and padded seat, and cushion. The seat shall feature an all belts to seat (ABTS) style of safety restraint. The ABTS feature shall include a three-point shoulder harness with the lap belt and automatic retractor as an integral part of the seat assembly. The buckle portion of the seat belt shall extend from the seat base towards the driver position within easy reach of the occupant. The minimum vertical dimension from the seat H-point to the ceiling for each belted seating position shall be 35.00 inches. This model of seat shall have successfully completed the static load tests by FMVSS 207/210. This testing shall include a simultaneous forward load of 3000 pounds each on the lap and shoulder belts and twenty (20) times the weight through the center of gravity. This model of seat installed in the cab model, as specified, shall have successfully completed the dynamic sled testing using FMVSS 208 as a guide with the following accommodations. In order to reflect the larger size outfitted firefighters, the test dummy used shall be a 95th percentile hybrid III male weighing 225 pounds rather than the 50th percentile male dummy weighing 165 pounds as referenced in FMVSS 208. The model of seats shall also have successfully completed the flammability of materials used in the occupant compartments of motor vehicles as outlined in FMVSS 302, of which decides the burning rate of materials in the occupant compartments of motor vehicles.

SEAT BACK REAR FACING OUTER

The rear facing outer seat back(s) shall include a Ziamatic brand model QM-EZL-F mechanical self-contained breathing apparatus (SCBA) bracket. The Mechanical walk away bracket shall meet NFPA 1901-09 9G dynamic requirements for cylinder restraint systems for use in crew compartments of fire truck cabs. The bracket shall secure a self-contained breathing apparatus with most sizes of cylinders. The bracket shall feature a top clamp and a footplate which securely lock the SCBA. The top clamp shall be PVC coated to prevent damage to the cylinder. The steel back plate and cast aluminum footplate shall be powder coated. The bracket shall also include a pull release cable with a handle which activates the lever on the bracket saving the occupant from reaching behind the SCBA in order to release the bracket. The handle shall be located on the front of the seat in the center. The seat back shall include a removable padded cover which shall be provided over the SCBA cavity.

SEAT MOUNTING REAR FACING OUTER

The rear facing outer seats shall offer special mounting positions which shall be 2.00 inches towards the rear wall offering additional space between the front seats and the outer rear facing seats.

OCCUPANT PROTECTION RFO

The rear facing outer seat position(s) shall be equipped with the Advanced Protection System™ (APS). The APS shall selectively deploy integrated systems to protect against injuries in qualifying frontal

impact, side impact, and rollover events. The increase in survivable space and security of the APS shall also provide ejection mitigation protection. Each rear facing outer seating position APS shall include: • APS advanced seat belt system - retractor pre-tensioners tighten the seat belts around each occupant, securing the occupants in seats and load limiters play out some of the seat belt webbing to reduce seat belt to chest and torso force upon impact as well as mitigate head and neck injuries. Side curtain airbag - protects each occupant's head, neck, and upper body from dangerous cab side surfaces and contact points with intrusive surfaces as a result of a collision as well as provides ejection mitigation protection to each occupant in a qualifying event by covering the windows and walls adjacent to each seating position with an airbag custom designed for each cab configuration.

CAB FRONT UNDERSEAT STORAGE ACCESS

The left and right under seat storage areas shall have a solid aluminum hinged door with non-locking latch.

SEAT COMPARTMENT DOOR FINISH

All underseat storage compartment access doors shall have a multi-tone silver gray texture finish.

WINDSHIELD WIPER SYSTEM

The cab shall include a dual arm wiper system which shall clear the windshield of water, ice and debris. There shall be two (2) windshield wipers which shall be affixed to a radial wet arm. The system shall include a single motor which shall initiate the arm in which both the left hand and right hand windshield wipers are attached, initiating a back and forth motion for each wiper. The wiper motor shall be activated by an intermittent wiper control located within easy reach of the driver’s position.

ELECTRONIC WINDSHIELD FLUID LEVEL INDICATOR

The windshield washer fluid level shall be monitored electronically. When the washer fluid level becomes low the yellow “Check Message Center” indicator light on the instrument panel shall illuminate and the message center in the dual air pressure gauge shall display a “Check Washer Fluid Level” message.

CAB DOOR HARDWARE

The cab entry doors shall be equipped with exterior pull handles, suitable for use while wearing firefighter gloves. The handles shall be made of a fiber reinforced plastic composite with a black matt finish. The interior exit door handles shall be flush paddle type with a black finish, which are incorporated into the upper door panel.

All cab entry doors shall include locks which are keyed alike. The door locks shall be designed to prevent accidental lockout.

DOOR LOCKS

Each cab entry door shall include a manually operated door lock. Each door lock may be actuated from the inside of the cab by means of a red knob located on the paddle handle of the respective door or by using a TriMark key from the exterior. The door locks are designed to prevent accidental lock out.

GRAB HANDLES

The cab shall include one (1) 18.00 inch knurled, anti-slip, one-piece exterior assist handle behind each cab door. The grab handle shall be made of 14 gauge 304- stainless steel and be 1.25 inch diameter to enable non-slip assistance with a gloved hand.

REARVIEW MIRRORS

Retrac Aerodynamic West Coast style single vision mirror heads model 613275 shall be provided and installed on each of the front cab doors. The mirrors shall be mounted via 1.00 inch diameter tubular stainless steel arms to provide a rigid mounting to reduce mirror vibration. The mirrors shall measure 8.00 inches wide X 19.00 inches high and shall include an 8.00 inch convex mirrors with a stainless steel back, model 980-4, installed below the flat glass to provide a wider field of vision. The flat mirrors shall be motorized with remote horizontal and vertical adjustment. The control switches shall be mounted within easy reach of the driver. The convex mirrors shall be manually adjustable. The flat mirror glass shall be heated for defrosting in severe cold weather conditions. The mirrors shall be constructed of a vacuum formed chrome plated ABS plastic housing that is corrosion resistant and shall include the finest quality non-glare glass.

REARVIEW MIRROR HEAT SWITCH

The heat for the rearview mirrors shall be controlled through a rocker switch on the dash in the switch panel.

CAB FENDER

Full width wheel well liners shall be installed on the extruded cab to limit road splash and enable easier cleaning. Each two-piece liner shall consist of an inner liner 16.00 inches wide made of vacuum formed ABS composite and an outer fenderette 5.00 inches wide made of 12 gauge polished aluminum.

MUD FLAPS FRONT

The front wheel wells shall have mud flaps installed on them.

IGNITION

A master battery system with a keyless start ignition system shall be provided. Each system shall be controlled by a one-quarter turn Cole Hersee switch, both of which shall be mounted to the left of the steering wheel on the dash. A chrome push type starter button shall be provided adjacent to the master battery and ignition switches. Each switch shall illuminate a green LED indicator light on the dash when the respective switch is placed in the “ON” position. The starter button shall only operate when both the master battery and ignition switches are in the “ON” position.

BATTERY

The single start electrical system shall include six (6) Harris BCI 31 950 CCA batteries with a 210 minute reserve capacity and 4/0 welding type dual path starter cables per SAE J541.

BATTERY TRAY

The batteries shall be installed within two (2) steel battery trays located on the left side and right side of the chassis, securely bolted to the frame rails. The battery trays shall be coated with the same material as the frame. The battery trays shall include drain holes in the bottom for sufficient drainage of water. A durable, non-conducting, interlocking mat made by Dri-Dek shall be installed in the bottom of the trays to allow for air flow and help prevent moisture build up. The batteries shall be held in place by non-conducting phenolic resin hold down boards.

BATTERY BOX COVER

Each battery box shall include a steel cover which protects the top of the batteries. Each cover shall include flush latches which shall keep the cover secure as well as a black powder coated handle for convenience when opening.

BATTERY CABLE

The starting system shall include cables which shall be protected by 275 degree F. minimum high temperature flame retardant loom, sealed at the ends with heat shrink and sealant.

BATTERY JUMPER STUD

The starting system shall include battery jumper studs. These studs shall be located in the forward most portion of the driver's side lower step. The studs shall allow the vehicle to be jump started, charged, or the cab to be raised in an emergency in the event of battery failure.

ALTERNATOR

The charging system shall include a 320 amp Leece-Neville 12 volt alternator. The alternator shall include a self-exciting integral regulator.

BATTERY CONDITIONER

A Kussmaul 1200 battery conditioner shall be supplied. The battery conditioner shall be mounted in the cab in the LH rear facing outer seating position.

BATTERY CONDITIONER DISPLAY

A Kussmaul battery conditioner display shall be supplied. The battery conditioner display shall be mounted in the cab, viewable through the cab mid side window behind the left front door.

AUXILIARY AIR COMPRESSOR

A Kussmaul Auto Pump 120V air compressor shall be supplied. The air compressor shall be installed behind the officer's seat. The air compressor shall be plumbed to the air brake system to maintain air pressure.

ELECTRICAL INLET

A Kussmaul 20 amp super auto-eject electrical receptacle shall be supplied. It shall automatically eject the plug when the starter button is depressed. A single item or an addition of multiple items must not exceed the rating of the electric inlet that it’s connected to.

Amp Draw Reference List: Kussmaul 1000 Charger - 3.5 Amps Kussmaul 1200 Charger - 10 Amps Kussmaul 35/10 Charger - 10 Amps 1000W Engine Heater - 8.33 Amps 1500W Engine Heater - 12.5 Amps

120V Air Compressor - 4.2 Amps

ELECTRICAL INLET LOCATION

An electrical inlet shall be installed on the left hand side of cab over the wheel well.

ELECTRICAL INLET CONNECTION

The electrical inlet shall be connected to the battery conditioner and the air pump.

ELECTRICAL INLET COLOR

The electrical inlet connection shall include a yellow cover.

HEADLIGHTS

The cab front shall include four (4) rectangular halogen headlamps with separate high and low beams mounted in bright chrome bezels.

FRONT TURN SIGNALS

The front fascia shall include two (2) Whelen model 600 4.00 inch X 6.00 inch programmable LED amber turn signals which shall be installed in a chrome bezel outboard of the front warning and above the headlamps.

HEADLIGHT LOCATION

The headlights shall be located on the front fascia of the cab directly below the front warning lights.

SIDE TURN/MARKER LIGHTS

The sides of the cab shall include two (2) LED round side marker lights which shall be provided just behind the front cab radius corners.

MARKER AND ICC LIGHTS

In accordance with FMVSS, there shall be five (5) LED cab marker lamps designating identification, center and clearance provided. These lights shall be installed on the face of the cab within full view of other vehicles from ground level.

HEADLIGHT AND MARKER LIGHT ACTIVATION

The headlights and marker lights shall be controlled through a rocker switch within easy reach of the driver. There shall be a dimmer switch within easy reach of the driver to adjust the brightness of the dash lights. The headlamps shall be equipped with the "Daytime Running" light feature, which shall illuminate the headlights to 80% brilliance when the battery master switch is in the "On" position and the parking brake is released.

GROUND LIGHTS

Each door shall include an LED NFPA compliant ground light mounted to the under side of the cab step below each door. The lights shall include a polycarbonate lens, a housing which is vibration welded and LEDs which shall be shock mounted for extended life. The ground lighting shall be activated by the opening of the respective door as well as being activated when the parking brake is set.

LOWER CAB STEP LIGHTS

The middle step located at each door shall include a recess mounted 4.00 inch round LED light which shall activate with the opening of the respective door.

INTERMEDIATE STEP LIGHTS

The intermediate step well area at each door shall include an LED light within a chrome housing. The Egress step lights shall provide visibility to the step well area for the first step exiting the vehicle. The Egress step lights shall activate with Entry step lighting.

ENGINE COMPARTMENT LIGHT

There shall be an incandescent NFPA compliant light mounted under the engine tunnel for area work lighting on the engine. The light shall include a polycarbonate lens, a housing which is vibration welded and a bulb which shall be shock mounted for extended life. The light shall activate automatically when the cab is tilted.

FRONT SCENE LIGHTS

The front of the cab shall include one (1) Fire Research Focus Evolution model FCA800-V15 contour roof mount scene light installed on the brow of the cab. The lamp head shall have eight (8) ultra-bright white LEDs. The lamp head shall draw 13 amps and generate 15,000 lumens. The lamp head shall direct 50 percent of the light onto the action area while providing 50 percent to illuminate the working area. The angle of elevation of the lamp head shall be adjustable at a pivot in the mounting arm and the position locked with a round knurled locking knob. The lamp head shall incorporate heat-dissipating fins and be no more than 4.00 inches high by 11.50 inches wide. The lamp head shall be powder coated white.

FRONT SCENE LIGHTS ACTIVATION

The front scene lighting shall be activated by a rocker switch.

FRONT SCENE LIGHT LOCATION

There shall be one (1) scene light mounted center on the front brow of the cab.

SIDE SCENE LIGHTS

The side of the cab shall include two (2) Whelen 900 series 9SC0ENZR model scene lights, one (1) each side which shall be surface mounted with a chrome bezel. The Whelen lights shall offer LED lighting at a gradient 32-degree angle.

SIDE SCENE LIGHT LOCATION

The scene lighting located on the left and right sides of the cab shall be mounted rearward of the cab “B” pillar in the 10.00 inch raised roof portion of the cab between the front and rear crew doors.

SIDE SCENE ACTIVATION

The scene lights shall be activated by two (2) rocker switches located in the switch panel, one (1) for each light.

INTERIOR OVERHEAD LIGHTS

The cab shall include a two-section, red and clear Weldon incandescent dome lamp located over each door. The dome lamps shall be rectangular in shape and shall measure approximately 9.50 inches in length X 5.00 inches in width with a black colored bezel. The clear portion of each lamp shall be activated by opening the respective door and both the red and clear portions can be activated by individual switches on each lamp.

An additional two-section Weldon incandescent red and clear lamp shall be provided over the engine tunnel which can be activated by individual switches on the lamp.

DO NOT MOVE APPARATUS LIGHT

The front headliner of the cab shall include a flashing red light clearly labeled "Do Not Move Apparatus". In addition to the flashing red light, an audible alarm shall be included which shall sound while the light is activated. The flashing red light shall be 6.00 inches long X 2.50 inches wide X 1.75 inches high and shall be located centered left to right for greatest visibility. The light and alarm shall be interlocked for activation when either a cab door is not firmly closed or an apparatus compartment door is not closed, and the parking brake is released.

MASTER WARNING SWITCH

A master switch shall be included in the main rocker switch panel. The switch shall be a rocker type, red in color and labeled “Master” for identification. The switch shall feature control over all devices wired through it. Any warning device switch left in the “ON” position shall automatically power up when the master switch is activated.

HEADLIGHT FLASHER

An alternating high beam headlight flashing system shall be installed into the high beam headlight circuit which shall allow the high beams to flash alternately from left to right. Deliberate operator selection of high beams will override the flashing function until low beams are again selected. Per NFPA, these clear flashing lights will also be disabled “On Scene” when the park brake is applied.

HEADLIGHT FLASHER SWITCH

The flashing headlights shall be activated through a rocker switch on the switch panel. The rocker switch shall be clearly labeled for identification.

INBOARD FRONT WARNING LIGHTS

The cab front fascia shall include two (2) Whelen 600 series Super LED front warning lights in the left and right inboard positions. The lights shall feature multiple flash patterns including steady burn for solid colors and multiple flash patterns for split colors. The lights shall be mounted to the front fascia of the cab within a chrome bezel.

INBOARD FRONT WARNING LIGHTS COLOR

The warning lights mounted on the cab front fascia in the inboard positions shall be red.

FRONT WARNING SWITCH

The front warning lights shall be controlled via rocker switch on the panel. This switch shall be clearly labeled for identification.

INTERSECTION WARNING LIGHTS

The chassis shall include two (2) Whelen 600 series Super LED intersection warning lights, one (1) each side. The lights shall feature multiple flash patterns including steady burn for solid colors and multiple flash patterns for split colors.

INTERSECTION WARNING LIGHTS COLOR

The intersection lights shall be red.

INTERSECTION WARNING LIGHTS LOCATION

The intersection lights shall be mounted on the side of the bumper in the rearward position.

SIDE WARNING LIGHTS

The cab sides shall include two (2) Whelen 600 series Super LED warning lights, one (1) on each side. The lights shall feature multiple flash patterns including steady burn for solid colors and multiple flash patterns for split colors. The lights shall be mounted to the sides of the cab within a chrome bezel.

SIDE WARNING LIGHTS COLOR

The warning lights located on the side of the cab shall be red.

SIDE WARNING LIGHTS LOCATION

The warning lights on the side of the cab shall be mounted over the front wheel well directly over the center of the front axle.

SIDE AND INTERSECTOR WARNING SWITCH

The side and intersector warning lights shall be controlled by a rocker switch on the switch panel. This switch shall be clearly labeled for identification.

TANK LEVEL LIGHTS

There shall be two (2) Whelen PSTANK water level light strips surface mounted vertically, one (1) on each side of the cab behind the rear cab doors. The light strips shall feature four (4) colors of LED lights to indicate the fluid level of a tank. The colors from top to bottom shall be green, blue, amber, and red.

SIREN CONTROL HEAD

A Whelen 295HFS2 electronic siren control head with remote amplifier shall be provided and flush mounted in the switch panel with a location specific to the customer’s needs. The siren shall feature

200-watt output, hands free mode and shall be in “standby” mode awaiting instruction. The siren shall offer radio broadcast, public address, wail, yelp, or piercer tones and hands free operation which shall allow the operator to turn the siren on and off from the horn ring if a horn/siren selector switch option is also selected.

HORN BUTTON SELECTOR SWITCH

A rocker switch shall be installed in the switch panel between the driver and officer to allow control of either the electric horn or the air horn from the steering wheel horn button. The electric horn shall sound by default when the selector switch is in either position to meet FMCSA requirements.

AIR HORN ACTIVATION

The air horn activation shall be accomplished by the steering wheel horn button for the driver and a right hand side Linemaster model SP491-S81 foot switch for the officer. An air horn activation circuit shall be provided to the chassis harness pump panel harness connector.

MECHANICAL SIREN ACTIVATION

The mechanical siren shall be actuated by two (2) Linemaster model SP491-S81 foot switches mounted in the front section of the cab for use by the driver and officer. A red momentary siren brake rocker switch shall be provided in the switch panel on the dash. The siren shall only be active when master warning switch is on to prevent accidental engagement.

BACK-UP ALARM

An ECCO model 575 backup alarm shall be installed at the rear of the chassis with an output level of 107 dB. The alarm shall automatically activate when the transmission is placed in reverse.

INSTRUMENTATION

An ergonomically designed instrument panel shall be provided. Each gauge shall be backlit with LED lamps. Stepper motor movements shall drive all gauges. The instrumentation system shall be multiplexed and shall receive ABS, engine, and transmission information over the J1939 data bus to reduce redundant sensors and wiring. The instrument panel shall contain the following gauges: One (1) electronic speedometer shall be included. The primary scale on the speedometer shall read from 0 to 100 MPH, and the secondary scale on the speedometer shall read from 0 to 160 KM/H. One (1) electronic tachometer shall be included. The scale on the tachometer shall read from 0 to 3000 RPM. One (1) two-movement gauge displaying primary system, and secondary system air volumes and integral LCD odometer/trip odometer shall be included on the lower portion of the LCD. The scale on the air pressure gauges shall read from 0 to 150 pounds per square inch (PSI). The air pressure scales shall be linear to operate with an accuracy of 1 degree of the measured data with a red indication zone

on the gauge showing critical levels of air pressure. A red indicator light in the gauge shall indicate a low air pressure, as well as a message on the LCD screen. The odometer shall display up to 9,999,999.9 miles. The trip odometer shall display 9,999.9 miles. The LCD shall display Transmission Temperature in degrees Fahrenheit on the upper portion of the LCD. The LCD screen shall also be capable of displaying certain diagnostic functions. One (1) four-movement gauge displaying engine oil pressure, coolant temperature, fuel level, voltmeter, and an *indicator bar displaying Diesel Exhaust Fluid (DEF) LED bar shall be included. The scale on the engine oil pressure gauge shall read from 0 to 120 pounds per square inch (PSI). The engine oil pressure scale shall be linear to operate with an accuracy of 1 degree of the measured. A red indicator light in the gauge shall indicate a low engine oil pressure, as well as a message on the LCD screen. The scale on the coolant temperature gauge shall read from 100 to 250 degrees Fahrenheit (F). The coolant temperature scale shall be linear to operate with an accuracy of 1 degree of the measured data with a red indication zone on the gauge showing critical levels of air pressure. A red indicator light in the gauge shall indicate high coolant temperature, as well as a message on the LCD screen. The scale on the fuel level gauge shall read from empty to full as a percentage of fuel remaining. An amber indicator light shall indicate low fuel at 25% tank level. The scale on the voltmeter shall read from 10 to 16 volts with a red indication zone on the gauge showing critical levels of battery voltage. A red indicator light shall indicate high or low system voltage, as well as a message on the LCD screen. The scale on the DEF LED bar will consist of four (4) LEDs displaying levels in increments of 25% of useable DEF in green. Upon decreasing levels, the indicator bar will change colors to notify the driver of decreasing levels of DEF and action will be required. An amber indicator light shall indicate low levels of DEF, as well as a message on the LCD screen and an audible alarm. The instrument panel shall include a light bar that contains the following LED indicator lights and produce the following audible alarms in applicable configurations:

RED LAMPS

Stop Engine-indicates critical engine fault Air Filter Restricted-indicates excessive engine air intake restriction Park Brake-indicates parking brake is set Seat Belt Indicator-indicates when a seat is occupied and corresponding seat belt remains unfastened Low Coolant-indicates engine coolant is required

AMBER LAMPS

MIL-indicates an engine emission control system fault Check Engine-indicates engine fault Check Trans-indicates transmission fault High Transmission Temperature-indicates excessive transmission oil temperature ABS-indicates anti-lock brake system fault HEST-indicates a high exhaust system temperature Water in Fuel-indicates presence of water in fuel filter *DPF-indicates a restriction of the diesel particulate filter *Regen Inhibit-indicates regeneration has been postponed due to user interaction Range Inhibit-indicates a transmission operation is prevented and requested shift request may not occur. *SRS-indicates a problem in the supplemental restraint system Check Message-Turn Signal On Check Message-Door Ajar Check Message-Cab Ajar

*Check Message-ESC Active *Check Message-DPF Regen Active Check Message-No Engine Data Check Message-No Transmission Data Check Message-No ABS Data Check Message-No Data All Communication With The Vehicle Systems Has Been Lost Check Message-Check Engine Oil Level Check Message-Check Washer Fluid Level Check Message-Check Power Steering Fluid Level Check Message-Low Transmission Fluid Level Check Message-Check Coolant Level

GREEN LAMPS

Left and Right turn signal indicators *ATC-indicates low wheel traction for automatic traction control equipped vehicles, also indicates mud/snow mode is active for ATC system High Idle-indicates engine high idle is active. Cruise Control-indicates cruise control is active OK to Pump-indicates the pump engage conditions have been met Pump Engaged-indicates the pump is currently in use Auxiliary Brake-indicates secondary braking device is active

BLUE LAMP

High Beam Indicator

WHITE LAMP

Wait to Start-indicates active engine air preheat cycle

AUDIBLE ALARMS FROM GAUGE PACKAGE

High Trans Temp High or Low Voltage Check Engine Check Transmission Stop Engine Low Air Pressure Fuel Low Water in Fuel *ESC High Coolant Temperature Low Engine Oil Pressure Low Coolant Level *Low DEF Level Air Filter Restricted Extended Left and Right Turn Remaining On Cab Ajar Door Ajar ABS System Fault Seatbelt Indicator

EXTERNAL AUDIBLE ALARM

Air Filter Cab Ajar Door Ajar Check Engine Stop Engine Low Air Pressure Low Engine Oil Pressure Water in Fuel *Low DEF ABS System Fault Seatbelt Indicator *Items marked with an asterisk are provided only in applicable configurations.

LCD MESSAGES

Transmission Temperature Battery Voltage Engine Hours Vehicle Speed Engine RPMs Fuel Level DEF Level Engine Oil Pressure Ammeter (If equipped) Auxiliary Ammeter (If equipped) Engine Coolant Temp Primary System Air Pressure Secondary System Air Pressure Turbo Boost Pressure Exhaust Temperature Engine Load Engine Torque Instant Fuel Economy Average Fuel Economy

BACKLIGHTING COLOR

The instrumentation gauges and the switch panel legends shall be backlit using red LED backlighting.

COMMUNICATION ANTENNA

An antenna base, for use with an NMO type antenna, shall be mounted on the right hand front corner of the cab roof so not to interfere with light bars or other roof mounted equipment installed by Spartan Chassis. The antenna base shall be an Antenex model MABVT8 made for either a 0.38 inch or 0.75 inch receiving hole in the antenna and shall include 17.00 foot of RG58 A/U cable with no connector at the radio end of the cable. The antenna base design

provides the most corrosion resistance and best power transfer available from a high temper all brass construction and gold plated contact design.

The antenna base shall be provided by Spartan.

COMMUNICATION ANTENNA CABLE ROUTING

The antenna cable shall be routed from the antenna base mounted on the roof to the area underneath the right hand front seat.

CAB EXTERIOR PROTECTION

The cab face shall have a removable plastic film installed over the painted surfaces to protect the paint finish during transport to the body manufacturer.

FIRE EXTINGUISHER

A 2.50 pound D.O.T approved fire extinguisher with BC rating shall be shipped loose with the cab.

ROAD SAFETY KIT

The cab and chassis shall include one (1) emergency road safety triangle kit.

DOOR KEYS

The cab and chassis shall include a total of four (4) door keys for the manual door locks.

DIAGNOSTIC SOFTWARE OCCUPANT PROTECTION

Diagnostic software for the Spartan Advanced Protection System shall be available for free download from the Spartan Chassis website to Spartan authorized OEMs, dealers and service centers, as well as the vehicle owner. The software has been validated to be compatible with the following RP1210 interface adapters: • Dearborn Group DPA4 Plus • Noregon Systems JPRO ® DLA+ • Cummins INLINE5 • Cummins INLINE6 • NexIQ™ USB-Link™ The software and adapter utilize the SAE J1939-13 heavy duty nine (9) pin connector which is located below the driver’s side dash to the left of the steering column.

WARRANTY

Summary of Warranty Terms: THE FOLLOWING IS SUMMARY OF WARRANTY TERMS FOR INFORMATION ONLY. THE ACTUAL LIMITED WARRANTY DOCUMENT, WHICH IS ATTACHED TO THIS OPTION, CONTAINS THE COMPLETE STATEMENT OF THE SPARTAN MOTORS USA LIMITED WARRANTY. SPARTAN’S RESPONSIBILITY IS TO BE ACCORDING TO THE TERMS OF THE COMPLETE LIMITED WARRANTY DOCUMENT.

The chassis manufacturer shall provide a limited parts and labor warranty to the original purchaser of the custom built cab and chassis for a period of twenty-four (24) months, or the first 36,000 miles, whichever occurs first. The warranty period shall commence on the date the vehicle is delivered to the first end user.

CAB AND CHASSIS LABELING LANGUAGE

The cab and chassis shall include the applicable caution, warning, and safety notice labels with text to be written in English.

CHASSIS OPERATION MANUAL

There shall be two (2) digital copies of the chassis operation manual provided with the chassis. The digital data shall include a parts list specific to the chassis model.

ENGINE AND TRANSMISSION OPERATION MANUALS

The following manuals specific to the engine and transmission models ordered will be included with the chassis in the ship loose items: (2) Hard copies of the Engine Operation and Maintenance manual with CD (2) Digital copies of the Transmission Operator’s manual (2) Digital copies of the Engine Owner’s manual

CAB/CHASSIS AS BUILT WIRING DIAGRAMS

The cab and chassis shall include two (2) digital copies of wiring schematics and option wiring diagrams.

SALES TERMS

The sale of the Spartan Chassis shall be governed by the terms contained on the Sales Terms – Acceptance of Purchase Order document, a copy of which is attached to this option.

DRIVELINE LAYOUT CONFIRMATION

During the design phase of the chassis the Spartan Chassis driveline engineer shall submit the driveline layout to an OEM engineer to review the chassis design for any potential problems integrating the OEM body to the chassis. The OEM engineer shall provide approval to the driveline engineer prior to driveline bills of materials being released.

PROPOSAL

PROPOSAL

PROPOSAL

PROPOSAL

Fri Nov 06 2015 Quote #: 0015853 Page 1 of 11 Customer: Metropolitan Area Planning Council 60 Temple Place, 6th Floor Boston, MA 02111 Quote Summary with Notes Dealership: New England Fire Equipment and Apparatus 10 Stillman Road North Haven, CT 06473 Quote No: 0015853 S.O.#: 911099 911085 911059 911069 911060 980017 911102 911065 980003 911070 980016 911081 980015 980012 911066 911073 911096 911074 980011 900466 900139 900536 900656 900678 Chassis 910012 910019 005241 001200 910021 001379 General Info Section Custom Pumper Destination, United States Bidding Prerequisites, United States Intent of Specifications, Pumper Standards Version, NFPA 1901-2009 Description Performance Bond and Payment Bond, Required, 100% Bid Bond, Required, 10% No Certificate Required Unit Certification, NFPA 1901-2009, Pumper Firefighting Apparatus Documentation, NFPA Owner's Manuals, Electronic, (1) USB Drive Misc. Equipment Allowance, 2,500 Lb.

Tilt Table Test, Required, 26.5 Degrees Pump Certification, Independent Third Party Pump Certification Measure, U.S. GPM Pre-Construction Meeting, OEM Factory Pre-Paint Inspection, OEM Factory Showroom Final Inspection, OEM Factory, Required Final Inspection Option, Water Tank Filled Overall Height, 118 (9'-10") Overall Length, 384" (32'-0") Wheelbase, 188 (15'-8") Angle of Approach, 11 Degrees Angle of Departure, 12 Degrees Chassis Section Custom Chassis, Smeal, Sirius II Axles, Single Quote Name: Unit Type: FCAM 2016 High Range Pumper OEM Chassis Preparations, Sirius Mud Flaps, Custom Chassis Cab Electrical, Multiplex Heat Exchanger, Chassis Supplied and Installed

004096 000346 003989 000253 910173 910170 010089 010050 010060 010047 910177 005737 Hose Bed 110131 910386 910500 910384 110161 009342 110372 Body / Pump Module 002630 120790 120874

UPO0000945

November 4, 2015 Option ID

UPO0000943

110005 111597 911113

UPO0000944

120405 Water/Foam Tanks 110110 910157 000350 910161 010075

UPO0000648

Quote #: 0015853

Front Bumper Extension, Chassis Supplied, OEM Supplied and Installed SS Tread Plate Gravel Shield

Storage Well, Front Bumper, Center, Tread Plate Cover with Notch Map Console, 3-Slot (3" Binders), Abraded Map Console Location, Engine Tunnel Mounted, Drop-In

Battery Charger, Chassis Supplied & Installed

Flashlights, (5), Streamlight, Fire Vulcan LED, Orange, 44451, Vehicle Mount System Water/Foam Tanks Section Water Tank, UPF, 1500 U.S. Gallons Water Tank Mounting, Pumpers Water Tank Drain, 1-1/2" Valve, Pumpers Water Tank Fill Tower, UPF, Blue Water Tank Level Gauge, Innovative Controls SL Plus, Pump Operator's Panel

Water Tank Level Display, Inn. Cntrls SL Plus Monster Strip Light, Cab Sides, Rear of Body, IC Driver

Description Water Tank Overflow, UPF, 6", Pumpers w/o EHL Page 2 of 11 Auxiliary Vent, UPF Booted Cover Over Water Tank, Tread Plate Foam Tank, UPF, U.S. Gallon, 40 Foam Tank Type, Class B Foam Tank Fill Tower, UPF, Green Foam Tank Level Gauge, Innovative Controls SL Plus, Class B Foam Direct Tank Fill, 2-1/2", Driver's Side Rear, Akron 8825 Valve, TSC Handle, FNST Swivel Direct Tank Fill Fittings, Plug with Chain, 2-1/2" NST, South Park, Chrome Dump Valve, Manual, SS Newton 10x10, 36" Telescoping Chute Dump Valve Location, Rear of Body Dump Valve Tank Flange, UPF Hose Bed Section Hose Bed, Aluminum, Standard, Painted Primary Body Color Finish Hose Load, Double-Jacket Hose, 300' of 2-1/2" Hose Load, Rubber Hose, 1500' of 4" Hose Load, Double-Jacket Hose, 300' of 1-3/4" Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Button Snaps, Rear Bungee, Red Hose Bed Dividers, (2), 1/4" Alum., Adjustable, Abraded Hose Bed Loading Lights, (2) Rear, LED, Whelen, Micro MPBW Body / Pump Module 121075 000934 Body, 100" Wide, Custom Pumper, Single-Axle, Aluminum, 1/8" Side Compartment Doors, Lap Doors, Painted Compartment Door Handles, All Non-Locking

Rear Compartment Doors, (2), Painted Lap Doors, Non-Locking, Open Rear Center Below Dump Valve

Compartment Lighting, On-Scene, Access Series LED (10) Compartment Finish, Line-X, Gray

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 2 of 11

000474 000440 900966 120709 L1 Height Width Upper Depth Lower Depth Divide Height 900981 002740 000565 000563 007876 004855 120785 Cmpt. Layout L2 Height Width Upper Depth Lower Depth Divide Height 900982 004855 001272 120785 Cmpt. Layout L3 Height Width Upper Depth Lower Depth Divide Height 900984 120292 000563 120785 Cmpt. Layout 009397 009421 120735 November 4, 2015 Option ID 120469 Quote #: 0015853 Description Page 3 of 11 Flooring, Turtle Tiles, All Interior Body Compartment Floors / Floor Mounted Trays and Shelves / Adjustable Trays Air Release and Drain Holes, All Compartments Sill Protectors, Anodized Aluminum Fuel Fill, Included with Air Bottle Compartment, Driver's Side Driver's (Left) Body Style, Single Axle, L1 Full, L2 Upper, L3 Full L1 Components Height - 58" Width - 35" Upper Depth - 15" Lower Depth - 26" Intermediate Divide Height - 27" Lap Door Hinge, Vertical, Forward Shelf, (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Abraded Tray, (1), Adjustable-Height Roll Out, Austin Hardware, 300#, 100% Extension, Abraded Tray, (1), Floor-Mounted Roll Out, Austin Hardware, 300#, 100% Extension, Abraded Flashlight, (1), Streamlight, Fire Vulcan LED, Orange, 44451, Vehicle Mount System Mounting Board, Back Wall of Compartment, PAC Trac Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

L2 Components Height - 25.5" Width - 65" Upper Depth - 15" Lower Depth - " Intermediate Divide Height - " Lap Door Hinge, Horizontal, Top Mounting Board, Back Wall of Compartment, PAC Trac SCBA Mounting, (1), Zico, Knock-Down Bracket, KD-UN-6-SF, with PHS Strap Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

L3 Components Height - 58" Width - 45" Upper Depth - 15" Lower Depth - 26" Intermediate Divide Height - 27" Lap Door Hinge, Vertical, Double Doors Shelves, (2), Adjustable, Aluminum, Shallow Depth (2 Struts), Abraded Tray, (1), Floor-Mounted Roll Out, Austin Hardware, 300#, 100% Extension, Abraded Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

WL1, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" WL3, Air Bottle Compartment with Fuel Fill, OEM Painted SS Door, Double 8" Officer's (Right) Body Style, Single Axle, R1 Lower, R2 Lower

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 3 of 11

November 4, 2015 Option ID R1 Height Width Upper Depth Lower Depth Divide Height 900984 120785 Cmpt. Layout R2 Height Width Upper Depth Lower Depth Divide Height 900984 120785 Cmpt. Layout 009436 009459 121489 T1 Height Width Depth 120785 Cmpt. Layout T2 Height Width Depth 120785 Cmpt. Layout T3 Height Width Depth 120785 Cmpt. Layout 005119 900963 005154 005118 010080 Quote #: 0015853 Description Page 4 of 11 R1 Components Height - 23.5" Width - 35" Upper Depth - 26" Lower Depth - " Intermediate Divide Height - " Lap Door Hinge, Vertical, Double Doors Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

R2 Components Height - 26.5" Width - 45" Upper Depth - 26" Lower Depth - " Intermediate Divide Height - " Lap Door Hinge, Vertical, Double Doors Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

WR1, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" WR3, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" Rear Body Style, Recessed Back, Standard Hose Bed, Three Compartments T1 Components Height - 26.5" Width - 8" Depth - " Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

T2 Components Height - 26.5" Width - 8" Depth - " Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

T3 Components Height - 12" Width - 22" Depth - 20" Compartment Struts, Vertical, Welded Aluminum The compartment layout shall be detailed at the pre-construction meeting.

Sub-Frame, GS-36, Hot-Dip Galvanized, Custom Pumpers, Aluminum and Galvaneal Bodies Walkways/Overlays/Stepping Surfaces, Tread Plate, NFPA 1901 Rear Deck, Bolt-On, Recessed Back, Tread Plate, Full Depth Sides Rub Rails, "C" Channel Design Tow Option, Rear, Tow Eye, One (1), Underbody Subframe

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 4 of 11

November 4, 2015 Option ID Quote #: 0015853 Description Page 5 of 11 002186 003559 120489 004929 002427 005155 001210

UPO0000946

007897 007899 120555 005144

UPO0000947 UPO0000948 UPO0000949 UPO0000950 UPO0000951

002717 001296 001293 001291 007194 009218 008208 008215 009306 121406 009280 001224 900951 002416 110174 004731 009855 000458

UPO0000952 UPO0000953

009973 Wheel Wells, Rear, Single Axle Fenderettes, (2), Single Axle, Stainless Steel Exhaust Heat Deflector Shield, 4" Access Panel for Fuel Tank Gauge, Pumpers License Plate Bracket Stainless Steel Screws Bag of Bolts

Overlay, Stainless Steel Treadbrite, Vertical Areas of Both Front Compartments

Front Steps and Lighting, Cast Products, Folding Steps (4), Driver's Side Front Step and Lighting, Cast Products, Folding Step (1), Officer's Side Rear Steps and Lighting, Cast Products, Folding, Eight (8), 4 Driver's Side and 4 Officer's Side Rear Step, Below Hose Bed, Full-Width Tread Plate

Handrail Material, Knurled Aluminum, LED (Red) Backlit, Hansen Handrail, Body (Front), Top, Driver's Side, Knurled Aluminum, Hansen Backlit Red, EPDM Rubber Handrail, Body (Front), Top, Officer's Side, Knurled Aluminum, Hansen Backlit Red, EPDM Rubber Handrail, Body (Rear), Rear Face, Vertical, Driver's Side, Knurled Aluminum, Hansen Backlit Red, EPDM Rubber Handrail, Body (Rear), Below Hose Bed, Horizontal, Knurled Aluminum, Hansen Backlit Red, EPDM Rubber

Ladder Storage, Above Low Sides, Officer's Side, OEM Brackets Ladder, (1), Duo-Safety, 24' Two-Section Extension, 900-A Ladder, (1), Duo-Safety, 14' Roof, 775-A Ladder, (1), Duo-Safety, 10' Folding Attic, 585-A Skull-Saver, FRC, (1) Pike Pole Tubes, (2), Ladder Storage Above Low Sides, Mounted on Catwalk, Officer's Side Pike Pole, (1), Fire Hooks Unlimited, 6' Fiberglass, All Purpose Hook, APH-6 Pike Pole, (1), Fire Hooks Unlimited, 10' Fiberglass, New Yorker Hook, Ash Core Super, NYFG-10 Hard Suction Hose Storage, Two (2) Hoses, Behind Driver's Side Header, Enclosed Compartment, Painted Door Hard Suction Hose, (2), Firequip, 6" x 10' (OAL 10' 6"), Maxi-Flex PVC Hard Suction Hose Storage, One (1) Hose, Above Officer's Side Low Cmpt, 'V' Trough (Painted), Retaining Straps Hard Suction Hose, (1), Firequip, 6" x 10' (OAL 10' 6"), Maxi-Flex PVC Wheel Chock Storage, Under Front of Body, Driver's Side Wheel Chocks, (1) Pair, Cast Products, TMC1008-4 (Chocks Only) Pump Module, Side Mount, Independent, 1/8" Aluminum Pump Compartment Internal Lighting, LED, On-Scene Pump Compartment Heater, (1) 40,000 BTU, Switch on Pump Panel Heat Shield, Removable, Heavy Duty

Running Board, Driver's Side, Bolt-On, Stainless Steel Tread Plate Running Board, Officer's Side, Bolt-On, Stainleess Steel Tread Plate

Dunnage Compartment, Tread Plate, Above Pump Module, NO Cover

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 5 of 11

November 4, 2015 Option ID Quote #: 0015853 Description Page 6 of 11 007160

UPO0000954

110222 003659 910612 Pump / Foam System 110260 000090 007296 910622 910640 910644 009531 002210 100309 000112 910645 111069 100725 004931 980014 006644 910503 911031 111059 911038 910527 100377 100360 100334 100310 910649 Tank/Pump Plumbing Labels Intakes 100382 005619 111073 111076 100476 Access Panel, Pump, Front Pump Module, Bolt-On, Painted Aluminum, Bolt-On

Pump Access Panel, Right Side, Stainless Steel with Two Compression Latches

Pump Panels, Side Mount, Controls on Driver's Side, Black Line-X Finish, IC Bezels/Trim Rings/Labels Pump Panel Lighting, Side Panels, LED, On-Scene Night Axe Pump Panel Lighting Activation, Automatic with Park Brake Engaged Pump / Foam System Pump, Waterous, Single-Stage (PTO), 1500 GPM, CXSPA, Flame Plated Impeller Hubs Mechanical Seals, Waterous Anodes, OEM, Alloy, 1 Intake Pump Rating, 1500 GPM Pump Mounting, Independent Pump Module Hot Shift PTO Connection, Stationary Governor, Pump Boss 400, FRC Intake Relief Valve, Pump, Elkhart, Factory Preset Primer, Trident, AirPrime (3-Barrel), Auto Prime and Vacuum Gauge, Remote Prime on Front Steamer Master Drain Valve, Trident Pump Color Primed Black - Intakes Unpainted Pump and Engine Cooling System, Inn. Cntrls, 3/8" I.D., Hose, Controls on Pump Panel Foam System, FoamPro, 2002, Single System, Class B Foam, Flush System Refill System, FoamPro, Power-Fill, Single System Foam System Testing, Single System Manifold, Waterous, Standard, Side Mounts, Foam Akron 8800 - Push/Pull Discharges (RC-10 on 3" or Larger) - Manual Inlets Gauge Brand, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauges - psi 0-400, LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-400, Both White LED Backlit Include with Master Pressure Gauge Assembly Hardware Brand, South Park, NST Inlet Swivels, NST Discharges, TFT Storz Drains, Innovative Controls, Manual Lift Handle Pump to Tank Fill, 2.5", Akron 8800 2.5" Manual Valve, IC Push-Pull Handle Tank to Pump, 4", Akron 8800 3" Manual Valve, IC Push-Pull Handle Tank to Pump, 3", Akron 8800 3" Manual Valve, IC Push-Pull Handle Secondary Sump Location, Front of Water Tank Tank/Pump Plumbing Labels - The tank plumbing valves and controllers shall have the OEM Standard label package unless stated otherwise. The Pump-to-Tank Fill shall be labeled "TANK FILL" and shall have a Black label color. The Tank-To-Pump shall be labeled "TANK TO PUMP" and shall have a Navy Blue label color.

Intakes Steamer, Driver Side, 6", Short Tube, Volute Pump, MNST Butterfly Valve, Side Steamer, 6" Manual, Neles Jamesbury Bleeder Valve, Inn. Cntrls Intake Relief Valve, Steamer, Elkhart, Factory Preset Elbow (30 Deg.) 6" FNST x 4" Storz 30 Degree Elbow, 4" Cap and Chain, Rocker Lug, TFT

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 6 of 11

November 4, 2015 Option ID 002588 007059 001246 100386 005619 111073 111076 100476 002587 007059 001246 100396 007428 111073 111076 001252 Intake Labels Discharges 002545 111712 121433 100527 002545 111712 121433 100527 002538 100659 121433 100527 002538 100659 121433 100527 002553 100663 Quote #: 0015853 Description Page 7 of 11 Inlet, Driver-Side, 2-1/2", Fully Recessed Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, TSC Handle Plug, NST, 2-1/2", South Park Steamer, Officer Side, 6", Short Tube, Volute Pump, MNST Butterfly Valve, Side Steamer, 6" Manual, Neles Jamesbury Bleeder Valve, Inn. Cntrls Intake Relief Valve, Steamer, Elkhart, Factory Preset Elbow (30 Deg.) 6" FNST x 4" Storz 30 Degree Elbow, 4" Cap and Chain, Rocker Lug, TFT Inlet, Officer-Side, 2-1/2", Fully Recessed Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, TSC Handle Plug, NST, 2-1/2", South Park Steamer, Front, Officer's Side, 6", Vertical, 5" Piping, Custom Chassis, MNST Butterfly Valve, Front Steamer, 5" Air, Neles Jamesbury Bleeder Valve, Inn. Cntrls Intake Relief Valve, Steamer, Elkhart, Factory Preset Cap, 6" NST, Vented Chrome, South Park Intake Labels - All intakes shall have the OEM Standard label package unless stated otherwise. All intake labels shall be burgundy in color. Specific verbiage on each intake label tag shall be determined at the pre-construction meeting.

Discharges Discharge, Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8625, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8625, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Officer-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Officer-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Officer-Side, 4", NST (625 GPM) Valve, 3", Akron, Manual, Slow Close, 8830, Stainless Ball, Elkhart RC-10 Handwheel

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 7 of 11

November 4, 2015 Option ID Quote #: 0015853 Description Page 8 of 11 121433 100611 100488 910534 100658 121433

UPO0000351

111105 002543 100658 121433 100527 002543 100658 121433 100542 007440 007013 007018 000205 009840 002205 110290 910701 910654 100653 121433 910526 910701 910654 100653 121433 910526 910702 910660 100658 121433 910526 100512 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Direct Tank Fill Fittings, Elbow (30 Deg.) 4" FNST x 4" Storz, Storz Cap, TFT Discharge, Front Bumper Driver-Side, 2-1/2", Above Gravelshield, NST, 3" Plumbing Foam Capable Discharge Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit

Reducer, South Park, 2-1/2" FNST x 1-1/2" MNST, A3720-AC

Front Bumper Hosewell Option, Hose Out Indicator Light, Driver's Side Pump Panel Discharge, Rear Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Discharge, Rear Driver-Side, 2-1/2", NST (250 GPM) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNST - NST Cap, Chrome, South Park Crosslays, Above Pump Panel, (2) 1-1/2" and (1) 2-1/2" Pre-Connect Hose Bed Housing Coating, Abraded Finish Flooring, Dura-Dek Crosslay Rollers Crosslay Divider, (1), Black Line-X Aluminum, Notched Crosslay Cover, Hinged Bi-Fold Tread Plate Crosslay End Covers, Vinyl, C-Rail Top and Bungee Bottom, Red Preconnect, Crosslay/Speedlay, 1-1/2", NST Crosslay Load, 200' of 1-3/4" Hose, Single Stack Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Preconnect Discharge Preconnect, Crosslay/Speedlay, 1-1/2", NST Crosslay Load, 200' of 1-3/4" Hose, Single Stack Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Preconnect Discharge Preconnect, Swivel, Crosslay/Speedlay, 2-1/2", NST Crosslay Load, 200' of 2-1/2" Hose, Single Stack Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit Preconnect Discharge Deluge, Center, 3", NPT (375 GPM)

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 8 of 11

November 4, 2015 Option ID Quote #: 0015853 Description Page 9 of 11 100663 121433

UPO0000955

112013 001256

UPO0000956

910534 100643 121433 Valve, 3", Akron, Manual, Slow Close, 8830, Stainless Ball, Elkhart RC-10 Handwheel Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit

Deck Gun, Akron, Manual, Apollo 3416, with 4" Storz Inlet Ground Base

Monitor Color, Akron Red, Powder Coat, AkzoNobel Interpon PG000QF, No Texture Stacked Tips (Quad), Akron, 2499 (2-1/2" NH Inlet)

Roof Turret Discharge, Center, 3", Four-Bolt Flange

Foam Capable Discharge Valve, 3", Akron, Electric, 8630, Stainless Ball, 9323 Navigator Pro Controller (Valve Only) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, White LED Backlit

UPO0000957

112014 002604 001731

UPO0000958

910534 100663

Deck Gun, Electric, Akron Deck Master 3440, 3" NPT Inlet, 30' Tether Controller in L1

Monitor Color, Akron Black, Sherwin Williams #F63B13 Position Feedback, Akron, Position Indicator Nozzle, Electric, Akron Akromatic 1250 GPM, 5177 (2-1/2" NH)

Foam Bypass, Roof Turret

Foam Capable Discharge Valve, 3", Akron, Manual, Slow Close, 8830, Stainless Ball, Elkhart RC-10 Handwheel Discharge Labels Discharge Labels - All discharges shall have the OEM Standard label package unless stated otherwise. Each discharge label shall be a unique color. Specific verbiage and colors on each discharge label tag shall be determined at the pre-construction meeting.

Low Voltage Low Voltage 002955 911058 000843 005907 008730 110366 110370 006261 004882 100035 Electrical System, Pumper, Weldon V-MUX Multiplex, QL-12 Harnesses, Sealed Switches Electrical System Test, 12 Volt Tail Lights, LED, Whelen, M6 Series, Stop-Tail (Combination)/Turn/Backup/Warning, 4-Light Vertical Casting Additional Activation, Back-Up Lights Wired to Rear Work Light Switch / In-Cab Switch Turn Signals, (2) in Rub Rail, LED, Truck-Lite, Model 21 Ground Lights, LED, Truck-Lite Model 44, Activation by Park Brake Parking Lights, Rear Fender Wells, LED, Tecniq E96 Clearance Lights, LED, Grote, Red (Pumper, Squrt, and TeleSqurt) 100016 004919 110409 Upper C Light / Lens Color 110487 Lower Zone Light/Lens Color 000890 007130 911005 010221 Camera System, Back-Up, Chassis Supplied, OEM Installed Intercom System, Firecom 5100D, 6 Cab Position, Wired Driver/Officer (UH-51), 4 Wired Crew (UH-52) Radio Interface Cable, Firecom, Motorola Upper Zone A, Lightbars (2), Whelen, 24", Freedom LED, FNMINI Upper Zone C, Rotating Beacons (2), Whelen, L31 LED Light/Lens Color - The driver's and officer's side beacons shall both have red LED's and red lenses.

Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, M6 Series Light/Lens Color - The lower zone warning lights shall all have red LED's and red lenses.

Air Horn Activation, Push Button on Pump Panel, Driver's Side Siren, Q2B, Chassis Supplied, OEM Installed, Pedestal Mount Siren Location, On Front Bumper, Pedestal Mounted, Center Power and Ground Lead, 12V Drop, Battery Direct, 10 Gauge Wire, 6-Position Distribution Panel

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 9 of 11

November 4, 2015 Option ID Quote #: 0015853 Description Page 10 of 11 900014 007544 910793 110843 110595 910851 110850 110595 910854 110850 110602 110832 110851 Line Voltage Paint / Striping / Decals 900717 009171 008841 001170 006089 001033 120012 120025 120034 120044 911237 900879 004522 008620 900888 900906 900924 900935 003624 008703 007284 Warranties W02450 990028 W05901 990032 WLF800 990030 W10201 Power Lead Location, In L1 Cmpt Scene Light, (1), 12V, FRC, Surface Mount, LED Spectra 15,000 Lumen Lighting Location, Rear Face of Body, Center Lighting Activation, On V-Mux Screen, 'REAR SCENE' Scene Lights, Pair, 12V, FRC, Surface Mount, LED Spectra 15,000 Lumen Lighting Location, Rear Face of Body, Both Sides Lighting Activation, Pair, In Cab, Individually Switched Lights, Rocker Switches Scene Lights, Pair, 12V, FRC, Surface Mount, LED Spectra 15,000 Lumen Lighting Location, Side Face of Body, Forward, Both Sides Lighting Activation, Pair, In Cab, Individually Switched Lights, Rocker Switches Scene Lights, Pair, 12V, FRC, Telescoping Side Mount Push-Up, LED Spectra 20,000 Lumen Lighting Location, On Rear Face of Custom Chassis, Both Sides Lighting Activation, Pair, On Pump Panel, Individually Switched Lights Line Voltage Paint / Striping / Decals Chassis Paint, Chassis Manufacturer Painted, Single Tone Body Paint, Single Tone, Pumper, Aluminum Material Body Paint Color, Pumper/Squrt/TS, Single Tone, Red, PPG# FBCH-71096-ALT Under Body Finish, Two-Step Undercoating Process Corrosion Protection, Electrolysis Corrosion Kontrol (ECK) Touchup Paint, 2 Oz. Bottle 10 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 40 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 15 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 5 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" Reflective Lettering, White Front Cab Striping, Wrap to Grill Rub Rail Striping, 2", Silver, Reflective, Pumper/Squrt/TS Body Striping, Pumper/Squrt/TS, 1"-4"-1", High Angle Transition Upper Stripe Color, White Main Stripe Color, White Lower Stripe Color, White Chevron Color, Red / Fluorescent Yellow-Green Chevron Layout, Center Portion of Recessed Back, T1 Lap Door, Painted Storage Doors Sign, Reflective, Rear Lap Door, 'Keep Back 500 Feet' Decal, Reflective, 9" Wavy American Flag with Eagle Head on Flag Warranties Warranty, Smeal Protection Plan, Material and Workmanship, 2 Year Warranty, Body Structural Integrity, 10 Year Warranty, 100% V-Mux Electrical, Smeal Parts and Labor, 5 Year (Pumper) Warranty, Plumbing, Stainless, 10 Year Warranty, Water Tank, UPF, Standard Lifetime Warranty, Substructure, Galvanized, 20 Year, Pumper, Rescue Warranty, Paint, 10 Year, Corrosion, 10 Year (Pumper)

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 10 of 11

November 4, 2015 Option ID W05810 Quote #: 0015853 Description Warranty, Pump, Waterous, Standard 5 Year Page 11 of 11

By: Rich Peck, 401-636-1585 http://www.smeal.com/ Page 11 of 11

Smeal High Range Chassis without Pricing

VEHICLE

0100-011 8012-002 8011-017 8001-001 8006-009 8008-001 0104-001 0101-003 0102-024 8010-004

MODEL CUSTOMERS / OEMS MODEL YEAR COUNTRY OF SERVICE APPARATUS TYPE VEHICLE TYPE AXLE CONFIGURATION GROSS AXLE WEIGHT RATINGS FRONT GROSS AXLE WEIGHT RATINGS REAR PUMP PROVISION

CAB

1000-013 8101-103 1501-002 1518-025 1551-002 1552-002 1521-002 1533-001 1522-075 1523-002 1524-002 1515-004 8013-036 1334-039 1005-001 1101-001 1322-002 8004-023 9001-006

CAB STYLE OCCUPANT PROTECTION CAB FRONT FASCIA FRONT GRILLE CAB UNDERCOAT CAB SIDE DRIP RAIL CAB PAINT EXTERIOR CAB PAINT MANUFACTURER CAB PAINT PRIMARY/LOWER COLOR CAB PAINT SECONDARY/UPPER COLOR CAB PAINT EXTERIOR BREAKLINE CAB PAINT PINSTRIPE CAB PAINT WARRANTY CAB PAINT INTERIOR CAB ENTRY DOORS CAB ENTRY DOOR TYPE CAB INSULATION CAB STRUCTURAL WARRANTY CAB TEST INFORMATION

ELECTRICAL POWER DISTRIBUTION

5000-002 5008-062 5005-215 5622-003 5031-005

ELECTRICAL SYSTEM OEM WIRING MULTIPLEX DISPLAY DATA RECORDING SYSTEM ACCESSORY POWER

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Qty. 1 1 1 1 1 1 1 1 1 1

5011-001

EXTERIOR ELECTRICAL TERMINAL COATING

ENGINE

1701-146

ENGINE

1329-001

CAB ENGINE TUNNEL

1731-002 1718-002 1719-005 1710-001 1713-010 1708-008 1720-003 1715-001 1735-001 8002-001 1707-016 1721-001 1727-001

DIESEL PARTICULATE FILTER CONTROLS ENGINE PROGRAMMING HIGH IDLE SPEED ENGINE HIGH IDLE CONTROL ENGINE PROGRAMMING ROAD SPEED GOVERNOR AUXILIARY ENGINE BRAKE AUXILIARY ENGINE BRAKE CONTROL ELECTRONIC ENGINE OIL LEVEL INDICATOR FLUID FILLS ENGINE DRAIN PLUG ENGINE WARRANTY REMOTE THROTTLE HARNESS ENGINE PROGRAMMING REMOTE THROTTLE ENGINE PROGRAMMING IDLE SPEED

COOLING

2704-002 2701-010 2711-005 2708-001 2706-003 2705-002 2709-004

ENGINE FAN DRIVE ENGINE COOLING SYSTEM ENGINE COOLING SYSTEM PROTECTION ENGINE COOLANT ELECTRONIC COOLANT LEVEL INDICATOR ENGINE PUMP HEAT EXCHANGER COOLANT HOSES

AIR INTAKE

2801-005 2802-003

ENGINE AIR INTAKE AIR INTAKE PROTECTION

EXHAUST

2901-030 2907-003 2902-004 2906-002

ENGINE EXHAUST SYSTEM DIESEL EXHAUST FLUID TANK ENGINE EXHAUST ACCESSORIES ENGINE EXHAUST WRAP

TRANSMISSION

1801-015 1806-003 1811-005 1815-002

TRANSMISSION TRANSMISSION MODE PROGRAMMING TRANSMISSION FEATURE PROGRAMMING ELECTRONIC TRANSMISSION OIL LEVEL INDICATOR

1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1807-005 1814-002 1808-007 1817-001 8005-001

TRANSMISSION SHIFT SELECTOR TRANSMISSION PRE-SELECT WITH AUXILIARY BRAKE TRANSMISSION COOLING SYSTEM TRANSMISSION DRAIN PLUG TRANSMISSION WARRANTY

POWER TAKE OFF

2005-009

PTO LOCATION

DRIVELINE

3001-001

DRIVELINE

3005-008

MIDSHIP PUMP / GEARBOX

FUEL SYSTEMS

3109-021 3111-001 3104-012 3103-008 3101-102 3130-004 3131-002 3102-016 3114-002 3115-001

FUEL FILTER/WATER SEPARATOR FUEL LINES FUEL SHUTOFF VALVE ELECTRIC FUEL PRIMER FUEL TANK FUEL TANK MATERIAL AND FINISH FUEL TANK STRAP MATERIAL FUEL TANK FILL PORT FUEL TANK SERVICEABILITY PROVISIONS FUEL TANK DRAIN PLUG

FRONT AXLE

2401-003 8059-013 2405-001

FRONT AXLE FRONT AXLE WARRANTY FRONT WHEEL BEARING LUBRICATION

FRONT SUSPENSION

2502-004 2501-006

FRONT SHOCK ABSORBERS FRONT SUSPENSION

STEERING

2601-006 2609-002 2603-001 2606-009 2610-003 2608-001

STEERING COLUMN/WHEEL ELECTRONIC POWER STEERING FLUID LEVEL INDICATOR POWER STEERING PUMP FRONT AXLE CRAMP ANGLE POWER STEERING GEAR CHASSIS ALIGNMENT

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3

REAR AXLE

3401-014 3403-001 8061-010 3411-001 3407-010 3408-004

REAR AXLE REAR AXLE DIFFERENTIAL LUBRICATION REAR AXLE WARRANTY REAR WHEEL BEARING LUBRICATION REAR AXLE DIFFERENTIAL CONTROL VEHICLE TOP SPEED

REAR SUSPENSION

3501G-00 1 3501-001

REAR SUSPENSION AUX SPRING REAR SUSPENSION

TIRES

3601-014 3602-021 3413-614 3606-003 3614-009

FRONT TIRE REAR TIRE REAR AXLE RATIO TIRE PRESSURE EQUALIZATION SYSTEM TIRE PRESSURE INDICATOR

WHEELS

3701-034 3703-050 3719-002 3702-002

FRONT WHEEL REAR WHEEL BALANCE WHEELS AND TIRES WHEEL TRIM

TIRE CHAINS

3801-012 3802-005

TIRE CHAINS TIRE CHAINS ACTIVATION

BRAKES

3205-014 3206-001 3207-009 3208-001 3204-029 3213-001 3214-002 3202-005 3215-001 3210-015

BRAKE SYSTEM FRONT BRAKES REAR BRAKES PARK BRAKE PARK BRAKE CONTROL FRONT BRAKE SLACK ADJUSTERS REAR BRAKE SLACK ADJUSTERS AIR DRYER FRONT BRAKE CHAMBERS REAR BRAKE CHAMBERS

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 4 1 1 1 2 4 1 1 1 1 4

AIR SUPPLY SYSTEMS

3320-001 3339-004 3305-010 3303-004 3307-001 3309-033 3349-006 3327-002 3326-002 3338-002

AIR COMPRESSOR AIR GOVERNOR AUXILIARY AIR RESERVOIR MOISTURE EJECTORS AIR SUPPLY LINES AIR INLET CONNECTION AIR INLET LOCATION PLUMBING AIR INLET CONNECTION AIR INLET/OUTLET FITTING TYPE REAR AIR TANK MOUNTING

FRAME

2103-1880 WHEELBASE 2106-1000 REAR OVERHANG 2101-002

FRAME

8007-019

FRAME WARRANTY

2117-004 2110-118

FRAME CLEAR AREA FRAME PAINT

BUMPER

2201-002 2202-006 2226-004

FRONT BUMPER FRONT BUMPER EXTENSION LENGTH

2206-001 2215-002 5503-022 2218-043 5501-012 2216-020

FRONT BUMPER EXTENSION FRAME WIDTH FRONT BUMPER PAINT FRONT BUMPER SUCTION PROVISION MECHANICAL SIREN MECHANICAL SIREN LOCATION AIR HORN AIR HORN LOCATION

2232QXX AIR HORN RESERVOIR 5504-060

ELECTRONIC SIREN SPEAKER

2217-005 2204-006

ELECTRONIC SIREN SPEAKER LOCATION FRONT BUMPER TOW EYES

CAB TILT

2301-001 2303-003 2305-001

CAB TILT SYSTEM CAB TILT LIMIT SWITCH CAB TILT CONTROL RECEPTACLE

CAB GLASS

1401-009 1402-008

CAB WINDSHIELD GLASS FRONT DOOR

1 1 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1407-001 1419-008 1430-001 1412-008 1431-001 1410-003 1432-001 1409-003 1433-001

GLASS TINT FRONT DOOR GLASS REAR DOOR RIGHT HAND GLASS TINT REAR DOOR RIGHT HAND GLASS REAR DOOR LEFT HAND GLASS TINT REAR DOOR LEFT HAND GLASS SIDE MID RIGHT HAND GLASS TINT SIDE MID RIGHT HAND GLASS SIDE MID LEFT HAND GLASS TINT SIDE MID LEFT HAND

CLIMATE CONTROL

1614-202 1632-002 1617-108 1620-019 1610-002 1603-003 1601-013 1608-002 1530-001

CLIMATE CONTROL CLIMATE CONTROL DRAIN CLIMATE CONTROL ACTIVATION HVAC OVERHEAD COVER PAINT HEATER HOSE INSULATION A/C CONDENSER LOCATION A/C COMPRESSOR CAB CIRCULATION FANS FRONT UNDER CAB INSULATION

CAB INTERIOR

1327-001 1302-001 1368-002 1306-006 1305-014 1339-102 1321-004 1307-002 5040-054 1303-017 1379-003 1102-013 1328-005 1323-001 1105-001 1308-001 1332-018 1345-002 1301-001 1337-002 1304-002

INTERIOR TRIM FLOOR INTERIOR TRIM REAR WALL INTERIOR TRIM HEADER TRIM TRIM CENTER DASH TRIM LEFT HAND DASH TRIM RIGHT HAND DASH ENGINE TUNNEL TRIM POWER POINT DASH MOUNT STEP TRIM UNDER CAB ACCESS DOOR INTERIOR DOOR TRIM DOOR TRIM SCUFF PLATE DOOR TRIM CUSTOMER NAMEPLATE CAB DOOR TRIM REFLECTIVE INTERIOR GRAB HANDLE "A" PILLAR INTERIOR GRAB HANDLE FRONT DOOR INTERIOR GRAB HANDLE REAR DOOR INTERIOR SOFT TRIM COLOR INTERIOR TRIM SUNVISOR INTERIOR FLOOR MAT COLOR

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1335-018 1371-021 1370-023 1378-022 1373-022 1344-002 1312-002 1313-002 1314-001

CAB PAINT INTERIOR DOOR TRIM HEADER TRIM INTERIOR PAINT TRIM CENTER DASH INTERIOR PAINT TRIM LEFT HAND DASH INTERIOR PAINT TRIM RIGHT HAND DASH INTERIOR PAINT DASH PANEL GROUP SWITCHES CENTER PANEL SWITCHES LEFT PANEL SWITCHES RIGHT PANEL

1225-007 1237-001 1243-003 1249-001 1201-006 1213-015 1219-001 8102-103 1202-009 1214-030 1220-002 8103-103 1273-001 1263-001 1203-009 1215-027 1221-009 8104-103 1266-001 1206-012 1218-031 8107-102 1269-101 1281-101 1224-002 1311-101 1355-023

CAB SEATS

SEAT BELT WARNING SEAT MATERIAL SEAT COLOR SEAT BACK LOGO SEAT DRIVER SEAT BACK DRIVER SEAT MOUNTING DRIVER OCCUPANT PROTECTION DRIVER SEAT OFFICER SEAT BACK OFFICER SEAT MOUNTING OFFICER OCCUPANT PROTECTION OFFICER SEAT BELT ORIENTATION CREW SEAT REAR FACING OUTER LOCATION SEAT CREW REAR FACING OUTER SEAT BACK REAR FACING OUTER SEAT MOUNTING REAR FACING OUTER OCCUPANT PROTECTION RFO SEAT FORWARD FACING CENTER LOCATION SEAT CREW FORWARD FACING CENTER SEAT BACK FORWARD FACING CENTER OCCUPANT PROTECTION FFC SEAT FRAME FORWARD FACING SEAT FRAME FORWARD FACING STORAGE ACCESS SEAT MOUNTING FORWARD FACING CENTER CAB FRONT UNDERSEAT STORAGE ACCESS DOOR SEAT COMPARTMENT DOOR FINISH

CAB EXTERIOR

1511-003 1534-002 1103-002

WINDSHIELD WIPER SYSTEM ELECTRONIC WINDSHIELD FLUID LEVEL INDICATOR CAB DOOR HARDWARE

1 1 1 7 1 1 1 1 1 1 1 1 1 1 1 1 6 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 2 2 1 1 1

1111-001 1503-013 1504-015 1529-004 1513-001 1514-002 1526-021

DOOR LOCKS GRAB HANDLES REARVIEW MIRRORS REARVIEW MIRROR HEAT SWITCH CAB FENDER MUD FLAPS FRONT CAB EXTERIOR FRONT & SIDE EMBLEMS

START / CHARGING SYSTEMS

5109-001 5101-002 5106-005 5107-008 5102-001 5108-002 5104-002

IGNITION BATTERY BATTERY TRAY BATTERY BOX COVER BATTERY CABLE BATTERY JUMPER STUD ALTERNATOR

LINE VOLTAGE ELECTRICAL POWER DISTRIBUTION

5202-004 5203-034 3314-006 5204-055 5209-029 5210-005 5206-002

BATTERY CONDITIONER BATTERY CONDITIONER DISPLAY AUXILIARY AIR COMPRESSOR ELECTRICAL INLET ELECTRICAL INLET LOCATION ELECTRICAL INLET CONNECTION ELECTRICAL INLET COLOR

5301-104 5303-017 5337-002 5336-003 5302-003 5350-061 5333-004 5308-011 5309-003 5382-002 5319-003 5312-002 5317-143 5335-003 5329-006 5306-112

LIGHTING

HEADLIGHTS FRONT TURN SIGNALS HEADLIGHT LOCATION SIDE TURN/MARKER LIGHTS MARKER & ICC LIGHTS HEADLIGHT AND MARKER LIGHT ACTIVATION CORNERING LIGHTS GROUND LIGHTS LOWER CAB STEP LIGHTS INTERMEDIATE STEP LIGHTS UNDER BUMPER LIGHTS ENGINE COMPARTMENT LIGHT FRONT SCENE LIGHTS FRONT SCENE LIGHTS ACTIVATION FRONT SCENE LIGHT LOCATION SIDE SCENE LIGHTS

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 8 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

5318-003 5316-008 5305-166

SIDE SCENE LIGHT LOCATION SIDE SCENE ACTIVATION INTERIOR OVERHEAD LIGHTS

OPTICAL WARNING DEVICES

5406-001 5422-002 5409-002 5425-003 5401-032 5413-002 5423-003 5404-027 5419-002 5420-002 5402-029 5418-002 5412-002 5424-003 5411-023 5407-019

DO NOT MOVE APPARATUS LIGHT MASTER WARNING SWITCH HEADLIGHT FLASHER HEADLIGHT FLASHER SWITCH INBOARD FRONT WARNING LIGHTS INBOARD FRONT WARNING LIGHTS COLOR FRONT WARNING SWITCH INTERSECTION WARNING LIGHTS INTERSECTION WARNING LIGHTS COLOR INTERSECTION WARNING LIGHTS LOCATION SIDE WARNING LIGHTS SIDE WARNING LIGHTS COLOR SIDE WARNING LIGHTS LOCATION SIDE AND INTERSECTION WARNING SWITCH TANK LEVEL LIGHTS INTERIOR DOOR OPEN WARNING LIGHTS

AUDIBLE WARNING DEVICES

5510-110 5514-005 5512-018 5513-021 5505-002

SIREN CONTROL HEAD HORN BUTTON SELECTOR SWITCH AIR HORN ACTIVATION MECHANICAL SIREN ACTIVATION BACK-UP ALARM

INSTRUMENTATION

5601-019 5624-001

INSTRUMENTATION BACKLIGHTING COLOR

COMMUNICATIONS SYSTEMS

5706-002 5703-010 5708-002 5709-003 5710-003 5020-001

CAMERA COMMUNICATION ANTENNA COMMUNICATION ANTENNA CABLE ROUTING AUXILIARY COMMUNICATION ANTENNA AUXILIARY COMMUNICATION ANTENNA CABLE ROUTING PANEL LAYOUT

ADDITIONAL EQUIPMENT

8814-002

CAB EXTERIOR PROTECTION

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 9

8806-001 8810-001 8811-003

FIRE EXTINGUISHER DOOR KEYS DIAGNOSTIC SOFTWARE OCCUPANT PROTECTION

SALES ADMIN

8003-140 8017-001 8030-006 8031-022 8032-009 8033-010 8805-007 8039-001

WARRANTY CAB AND CHASSIS LABELING LANGUAGE CHASSIS OPERATION MANUAL ENGINE & TRANSMISSION OPERATION MANUAL ENGINE SERVICE MANUAL TRANSMISSION SERVICE MANUAL CAB/CHASSIS AS BUILT WIRING DIAGRAMS SALES TERMS

ENGINEERING

9005-002 2124-002

DRIVELINE LAYOUT CONFIRMATION EFCM/REAR CROSSMEMBERS

1 1 1 1 1 1 1 1 1 1 1 1 1 10

PROPOSAL

PROPOSAL

PROPOSAL

PROPOSAL

000134 000137 000138 000139 000140 000161 000162 000163 000164 000175 000176 000177 000178 000179 000180 000078 000079 000080 000081 000086 000087 000090 000112 000113 000117 000118 000120 000122 000123 000133

Part Number

000006 000007 000008 000009 000014 000015 000035 000037 000061 000064 000073 000075 000076 000077 000181 000182 000183 000184 000190 000191 000192 000193 000199 000200 000202 000205 000206 000207 000210 000211 000215 000219 000220 000221 000222 000224 000225 000231 000235 000240 000241 000242 000243 000244 000248 000249 000250 000251 000252 000253 000254 000256 000257 000258 000260 000261 000262 000263 000264 000266 000268 000269 000270 000271 000273 000274 000275 000276

DESCRIPTION

Hose Bed Cover, Vinyl, Side Button Snaps, Rear Bungee Hose Bed Cover, Vinyl, Side Quarter-Turns, Rear Bungee Crosslays, Above Front Stabilizers, (2) 1-1/2" Butterfly Valve, 4", Elkhart, Gear, EB4B, With Handwheel Discharge, Front Bumper Officer-Side, 1-1/2", In Hosewell, NST Cut-Off Switch, Generator, Pump Panel Thermal Relief Valve (TRV), Hale, With Lights and Buzzer Mechanical Seals, Hale Overlay, Tread Plate, Vertical Areas of Body and Driver's Side Enclosed Pump Panels Overlay, Tread Plate, Vertical Areas of Both Sides of Enclosed Pump Panels Pump Panel Lighting, Enclosed Sides (4) On-Scene Night Axe LED Lights Pump Panel Lighting, Enclosed Side (2) On-Scene Night Axe LED Lights, Exposed Side On-Scene Night Axe LED Pump Panel Lighting, Enclosed Sides (4) ROM V4 LED Lights Pump Panel Lighting, Enclosed Side (2) ROM V4 LED Lights, Exposed Side On-Scene Night Axe LED Overlay, Tread Plate, Vertical Areas of Body and Officer's Side Enclosed Pump Panel Enclosed Pump Panels Doors, (2) Amdor Roll-Up Door Construction, Painted Finish Enclosed Pump Panels Doors, (2) ROM Roll-Up Door Construction, Painted Door, Sills, and Tracks Enclosed Pump Panels Doors, (2) ROM Roll-Up Door Construction, Painted Door Only Transfer Valve, Waterous, Electric, Manual Override Overheat Protection Manager (OPM), Waterous, With Lights Mechanical Seals, Waterous Master Drain Valve, Trident Speedlays in Lift Out Trays, Enclosed with Pump Panel, (2) 1-1/2", Stacked Speedlays on Roll Out Tray, Enclosed with Pump Panel, (2) 1-1/2" Speedlays in Lift Out Trays, Enclosed with Pump Panel, (2) 1-1/2" and (1) 2-1/2" Speedlays in Lift Out Trays, Ahead of Enclosed Pump Panel, (2) 1-1/2", Stacked Speedlays on Roll Out Tray, Ahead of Enclosed Pump Panel, (2) 1-1/2" Speedlays in Lift Out Trays, Ahead of Enclosed Pump Panel, (2) 1-1/2" and (1) 2-1/2" Pump Panel Lighting, Enclosed Sides (4) Amdor Luma Bar LED Lights Pump Panel Lighting, Enclosed Side (2) Amdor Luma Bar LED Lights, Exposed Side On-Scene Night Axe LED Speedlay End Covers, Webbing, Sides Over Rollers with Velcro Center, 2 Covers on Each Side Speedlay End Cover, Webbing, Sides Over Rollers with Velcro Center, 1 Cover on 1 Side Speedlay End Covers, Webbing, Sides Over Rollers with Velcro Center, 1 Cover on Each Side Speedlay End Covers, Webbing, Sides Over Rollers with Velcro Center, 2 Covers on 1 Side Speedlay End Covers, Tread Plate Upper Lift-Up and Lower Drop-Down, 2 Covers on Each Side Speedlay End Covers, Tread Plate Upper Lift-Up and Lower Drop-Down, 2 Covers on 1 Side Speedlay End Covers, Tread Plate, 1 Cover on Each Side Speedlay End Cover, Tread Plate, 1 Cover on 1 Side Hose Bed Cover, Vinyl, Top Button Snaps Hose Bed Cover, Vinyl, Top Quarter-Turns Hose Bed Cover, Vinyl, Top Velcro Hose Bed Covers (2), Vinyl, Top Button Snaps Hose Bed Covers (2), Vinyl, Top Quarter-Turns Hose Bed Covers (2), Vinyl, Top Bungee Hose Bed Covers (2), Vinyl, Top Velcro Hose Bed Cover, Vinyl, Top Quarter-Turns, Middle Button Snaps, Rear Footman Loop / J-Hook Hose Bed Cover, Vinyl, Top Bungee, Middle Button Snaps, Rear Footman Loop / J-Hook Hose Bed Cover, Vinyl, Top Button Snaps, Middle Bungee, Rear Footman Loop / J-Hook Air Chuck Blow-Out, Booster Reel, Booster Reel Swivel Foot Switch, Booster Reel, Below Rear Compartment Roller Assembly, Additional, Booster Reel, Above Dunnage Rewind Switch, Booster Reel, On Booster Reel Hose Bed Cover, Vinyl, Top Quarter-Turns, Middle Bungee, Rear Footman Loop / J-Hook Hose Bed Cover, Vinyl, Top Bungee, Middle Bungee, Rear Footman Loop / J-Hook Hose Bed Cover, Vinyl, Top Button Snaps, Middle Button Snaps, Rear Bungee Crosslay Rollers Hose Bed Cover, Vinyl, Top Quarter-Turns, Middle Button Snaps, Rear Bungee Hose Bed Cover, Vinyl, Top Bungee, Middle Button Snaps, Rear Bungee Hose Bed Cover, Vinyl, Top Button Snaps, Middle Bungee, Rear Bungee Hose Bed Cover, Vinyl, Top Quarter-Turns, Middle Bungee, Rear Bungee Hose Bed Cover, Vinyl, Top Bungee, Middle Bungee, Rear Bungee Transfer Valve, Waterous, Electric Scene Light, (1), 120V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 120V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 120V, Whelen, Telescoping Thru The Roof Pull-Up, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 120V, Whelen, Semi-Recessed, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 120V, Whelen, Brow Mount, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 120V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PFP2) Floodlight Scene Light, (1), 120V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PFP2) Floodlight Foam System, FoamPro, 2001, Single System, Class A Foam, NO Optional Flush System Foam System, FoamPro, 2001, Dual System, Manual Selector, Class A and B Foam, Flush System Scene Light, (1), 120V, Whelen, Telescoping Thru The Roof Pull-Up, LED Pioneer Plus (PFP2) Floodlight Foam System, FoamPro, 2002, Single System, Class A Foam, NO Optional Flush System Foam System, FoamPro, 1600, Single System, Class A Foam, NO Optional Flush System Scene Light, (1), 120V, Whelen, Semi-Recessed, LED Pioneer Plus (PFP2) Floodlight Scene Light, (1), 120V, Whelen, Brow Mount, LED Pioneer Plus (PFP2) Floodlight Foam Tank, UPF, U.S. Gallon, 10 Foam Tank, UPF, U.S. Gallon, 20 Foam Tank, UPF, U.S. Gallon, 30 Foam Tank, UPF, U.S. Gallon, 40 Foam Tank, UPF, U.S. Gallon, 50 Scene Light, (1), 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer (PFA1) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer (PFA1) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer (PFA1) Floodlight Foam Tank, Pro Poly, U.S. Gallon, 10 Scene Light, (1), 12V, Whelen, Semi-Recessed, LED Pioneer (PFA1) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer (PFA2) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer (PFA2) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer (PFA2) Floodlight Extend-A-Gun, Manual, TFT, 18", XG18VL-PL, For Non-Crossfire Monitor Scene Light, (1), 12V, Whelen, Semi-Recessed, LED Pioneer (PFA2) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 12V, Whelen, Semi-Recessed, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PFP2) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PFP2) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer Plus (PFP2) Floodlight

000560 000561 000562 000563 000564 000565 000566 000567 000568 000571 000572 000573 000574 000576 000577 000584 000585 000586 000587 000590 000591 000592 000593 000595 000596 000607 000608 000610 000612 000616 000617 000618 000619 000621 000626 000629 000631 000632 000278 000279 000280 000281 000303 000304 000306 000308 000310 000314 000316 000317 000346 000348 000349 000350 000366 000367 000368 000369 000370 000384 000385 000398 000401 000428 000440 000442 000458 000459 000460 000471 000474 000496 000497 000502 000505 000516 000518 000519 000521 000522 000523 000524 000526 000530 000531 000533 000534 000536 000541 000543 000544 000545 000546 000547 000550 000551 000554 000555 000559 Scene Light, (1), 12V, Whelen, Semi-Recessed, LED Pioneer Plus (PFP2) Floodlight Scene Light, (1), 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PCP2) Combo Spot/Flood Scene Light, (1), 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PCP2) Combo Spot/Flood Scene Light, (1), 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer Plus (PCP2) Combo Spot/Flood Scene Light, (1), 12V, Whelen, Semi-Recessed, LED Pioneer Plus (PCP2) Combo Spot/Flood Scene Light, (1), 12V, Whelen, Brow Mount, LED Pioneer (PFA1) Floodlight Scene Light, (1), 12V, Whelen, Brow Mount, LED Pioneer (PFA2) Floodlight Scene Light, (1), 12V, Whelen, Brow Mount, LED Pioneer Plus (PFP1) Floodlight Scene Light, (1), 12V, Whelen, Brow Mount, LED Pioneer Plus (PFP2) Floodlight Scene Light, (1), 12V, Whelen, Brow Mount, LED Pioneer Plus (PCP2) Combo Spot/Flood Hard Suction Hose, (1), Firequip, 6" x 8' (OAL 8'), Maxi-Flex PVC Hard Suction Hose, (1), Firequip, 6" x 12' (OAL 12'), Maxi-Flex PVC Auxiliary Vent, UPF Water Tank Overflow, UPF, 4", Pumpers w/ EHL, Aerials Water Tank Overflow, UPF, 6", Pumpers w/ EHL, Aerials Water Tank Drain, 1-1/2" Valve, Pumpers Door Open Warning Circuit, Wired to Light in Cab Door Open Warning Circuit, Whelen TIR3 Light in Cab Pressure Gauge, 2-1/2", Class 1, Liquid Filled - psi 0-400 Door Open Warning Circuit, Integrated in Vista Display in Cab Pressure Gauge, 3-1/2", Class 1, Liquid Filled - psi 0-400 Gauge, Extra Fuel Tank, On Pump Panel Gauge, Transmission Temperature, On Pump Panel Auxiliary Pump, Waterous, E511-C Rear Deck, Bolt-On, Flat Back, Grip Strut, 13.25" Struts, (2), Horizontal, Back Wall of Compartment, Aluminum Sill Protectors, Anodized Aluminum Grassfire Shield (Freestanding Wall) Heat Shield, Removable, Heavy Duty Access Panel, Pump, Driver's Side Pump Module, Side-Hinged, Tread Plate, Compression Latches Access Panel, Pump, Officer's Side Pump Module, Side-Hinged, Tread Plate, Compression Latches Vertical Partition, Permanent, Full Height Air Release and Drain Holes, All Compartments Ventilation Panel, SG-09, Officer's Side Pump Module, Bolt-On, Painted Aluminum Access/Ventilation Panel, SG-09, Driver's Side Pump Module, Side-Hinged, Tread Plate, Compression Latches Access Panel, SG-09, Front Pump Module, Tread Plate, SG-09 Overlay, Tread Plate, Vertical Areas of Both Front Compartments Tow Option, Rear, Tow Eye, Two (2), Chrome Handrail, Body (Rear), Hose Bed Riser, Vertical, Driver's Side, Knurled Aluminum Handrail, Body (Rear), Hose Bed Riser, Vertical, Officer's Side, Knurled Aluminum Handrail, Body (Front), Top, Officer's Side, Knurled Aluminum Bolt-In Lip, 2", Door Opening on Compartment Floor Handrails, Pump Module, Entrance of Walkway, Vertical, Both Sides, Knurled Aluminum Handrail, Pump Module, Top, Horizontal, Driver's Side, Knurled Aluminum Handrail, Body (Rear), Rear Face, Vertical, Driver's Side, Knurled Aluminum Handrail, Pump Module, Above Pump Panel, Horizontal, Driver's Side, Knurled Aluminum Handrail, Pump Module, Above Pump Panel, Horizontal, Officer's Side, Knurled Aluminum Light Tower Option, Command Light, Strobe, Green Light Tower Option, Command Light, Strobe, Blue Light Tower Option, Command Light, Strobe, Red Light Tower Option, Command Light, Strobe, Amber Light Tower Option, Will-Burt, Strobe, Green Light Tower Option, Will-Burt, Strobe, Blue Light Tower Option, Will-Burt, Strobe, Red Light Tower Option, Will-Burt, Strobe, Amber Light Tower Option, Will-Burt, Strobe, Clear Pressure Gauge, 2-1/2", Class 1, Liquid Filled - psi 0-600 Pressure Gauge, 3-1/2", Class 1, Liquid Filled - psi 0-400 - Red LED Lit Pressure Gauge, 3-1/2", Class 1, Liquid Filled - psi 0-400 - Blue LED Lit Pressure Gauge, 3-1/2", Class 1, Liquid Filled - psi 0-400 - White LED Lit Pressure Gauge, 3-1/2", Class 1, Liquid Filled - psi 0-400 - Green LED Lit Pressure Gauge, 3-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 - Red LED Lit Pressure Gauge, 3-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 - Blue LED Lit Tray, (1), Floor-Mounted Roll Out, Austin Hardware, 300#, 100% Extension, Line-X Tray, (1), Floor-Mounted Roll Out, Austin Hardware, 300#, 100% Extension, Abraded Tray, (1), Adjustable-Height Roll Out, Austin Hardware, 300#, 100% Extension, Line-X Tray, (1), Adjustable-Height Roll Out, Austin Hardware, 300#, 100% Extension, Abraded Pressure Gauge, 3-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 - White LED Lit Pressure Gauge, 3-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 - Green LED Lit Tray, (1), Adjustable-Height Tilt Down, Innovative Ind. 250#, Line-X Mounting Plate, Back Wall of Compartment, Black Poly Flowminder Value System, Class 1, Pressure Gauge, 2-1/2", Liquid Filled - psi 0-400 Mounting Plate, Back Wall of Compartment, Line-X Coated Aluminum Mounting Plate, Back Wall of Compartment, Abraded Aluminum Flowminder Value System, Class 1, Pressure Gauge, 2-1/2", Liquid Filled - psi 0-400 - Red LED Lit Flowminder Value System, Class 1, Pressure Gauge, 2-1/2", Liquid Filled - Dual Scale 0-400 / 0-2800 Flowminder Value System, Class 1, Pressure Gauge, 2-1/2", Liquid Filled - Dual Scale 0-400 / 0-2800 - Red LED Lit Flowminder Value System, Class 1, Pressure Gauge, 3-1/2", Liquid Filled - psi 0-400 Flowminder Value System, Class 1, Pressure Gauge, 3-1/2", Liquid Filled - psi 0-400 - Red LED Lit Flowminder Value System, Class 1, Pressure Gauge, 3-1/2", Liquid Filled - Dual Scale 0-400 / 0-2800 Flowminder Value System, Class 1, Pressure Gauge, 3-1/2", Liquid Filled - Dual Scale 0-400 / 0-2800 - Red LED Lit Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), psi -30-0-400, Both Red LED Backlit Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), psi -30-0-400, Both Blue LED Backlit Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), psi -30-0-400, Both White LED Backlit Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), psi -30-0-400, Both Green LED Backlit Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), Dual Scale -30-0-400 / -100-0-2800, Both Red LED Backlit Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), Dual Scale -30-0-400 / -100-0-2800, Both Blue LED Backlit Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), Dual Scale -30-0-400 / -100-0-2800, Both White LED Backlit Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), Dual Scale -30-0-400 / -100-0-2800, Both Green LED Backlit Hard Suction Hose Storage, Two (2) Hoses, Officer's Side of Hose Bed, Rack (Abraded), Retaining Straps Switch, Emergency Engine Shut-Down, Pump Panel Alarm, Discharge Relief Valve Alarm, Back-Up, Preco 1059 Dba Rear-Step Buzzer System Alarm, Door Open Warning Circuit Conduit, 1" Liquid-Tight with Fish Wire, Cab to Pump Panel Valve, 2-1/2", Waterous, 12V Manual Rotary Actuator, Full Flow, Crank Handle Controller Valve, 2-1/2", Waterous, 12V Manual Rotary Actuator, Full Flow, Electric Controller Map Light, Southern Vehicle Products, Top-Mounted, ML-6

000814 000815 000816 000817 000818 000819 000820 000821 000822 000823 000824 000825 000826 000827 000828 000829 000830 000831 000832 000833 000834 000835 000836 000842 000843 000844 000845 000846 000847 000849 000850 000851 000852 000853 000854 000857 000858 000859 000633 000635 000638 000639 000640 000641 000642 000645 000653 000654 000656 000662 000666 000669 000673 000674 000675 000676 000677 000678 000680 000681 000683 000684 000687 000697 000698 000699 000706 000715 000722 000723 000724 000738 000743 000744 000745 000748 000750 000761 000762 000763 000770 000773 000776 000780 000783 000784 000785 000799 000803 000804 000805 000806 000807 000808 000809 000810 000811 000812 000813 Valve, 3-1/2", Waterous, 12V Manual Rotary Actuator, Crank Handle Controller Valve, 3-1/2", Waterous, 12V Manual Rotary Actuator, Electric Controller Spotlight, In Cab, Collins, Handheld, Momentary Switch, CD-CL-12-M Scene Light, (1), 12V, Whelen, Surface Mount, Halogen 600 Series Opti-Scene Scene Light, (1), 12V, Whelen, Surface Mount, Halogen 700 Series Opti-Scene Scene Light, (1), 12V, Whelen, Surface Mount, Halogen 810 Series Scene Light, (1), 12V, Federal Signal, Surface Mount, GHScene Dual-Head Hose Bed Loading Light, (1) Rear, Halogen, Unity, AG-R Lighting Activation, In Cab, 'FRONT SCENE' Tool Board, (1), Slide Out Aluminum, Full Height, Full Depth, Double-Faced PAC TRAC Generator Start, Remote, Gas Gen., Honda, On Pump Panel Tool Board, (1), Slide Out Aluminum, Full Height, Full Depth, Abraded Pegboard Generator Start, Remote, Diesel Gen., Onan, In Cab Generator Start, Remote, Diesel Gen., Anderson, On Pump Panel Tool Board, (1), Slide Out Aluminum, Full Height, Split Depth, Abraded Tool Board, (1), Slide Out Aluminum, Full Height, Split Depth, Abraded Pegboard Auxiliary Cooling Fan and Duct Work Tool Board, (1), Slide Out Aluminum, Full Height, Split Depth, Line-X Tool Board, (1), Slide Out Aluminum, Full Height, Split Depth, Double-Faced PAC TRAC Tool Board, (1), Swing Out Aluminum, Standard Height, Abraded Generator PTO, Standard Hot Shift, Pumper Tool Board, (1), Swing Out Aluminum, Standard Height, Abraded Pegboard Generator Load Center, 8-Circuit, Non-GFI Breaker Box Generator Load Center, 8-Circuit, GFI Breaker Box Tool Board, (1), Swing Out Aluminum, Standard Height, Line-X Tool Board, (1), Swing Out Aluminum, Standard Height, Double-Faced PAC TRAC Tool Board, (1), Split Swing Out Aluminum, Standard Height, Abraded Tool Board, (1), Split Swing Out Aluminum, Standard Height, Abraded Pegboard Lighting Location, On Rear Face of Custom Chassis, Driver's Side Scene Light, (1), 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Focus 500W Tool Board, (1), Split Swing Out Aluminum, Standard Height, Line-X Tool Board, (1), Split Swing Out Aluminum, Standard Height, Double-Faced PAC TRAC Scene Lights, Pair, 120V, Chassis Supplied, Cab Side Scene (Wiring Only) Scene Light, (1), 240V, FRC, Telescoping Top Mount Pull-Up, Halogen Focus 1000W Scene Light, (1), 12V, Whelen, Surface Mount, LED M9 Series Gradient Scene Scene Light, (1), 12V, FRC, Surface Mount, LED Spectra 900 4,600 Lumen Audible Alarm for Hydraulic Equipment Rack Upper Zone A, Lightbar, Whelen, 55", Freedom LED, Flat Roof, 6 Red, 2 White Scene Light, (1), 120V, FRC, Recessed, Halogen Focus 500W Siren Head, 200W, Federal Signal, EQ2B Speaker, (1), 200W, Federal Signal, BP200-EF, Recess Mounted Speaker, (1), 200W, Federal Signal, BP200-Q, Recess Mounted Scene Light, (1), 12V, Whelen, Surface Mount, LED 700 Series Gradient Opti-Scene Scene Light, (1), 12V, Whelen, Surface Mount, LED 900 Series Gradient Opti-Scene Scene Light, (1), 12V, Whelen, Surface Mount, Halogen 900 Series Opti-Scene Upper Zone A, Lightbar, Code 3, 58", MX 7000, MX758A1 Upper Zone A, Lightbars (2), Code 3, 18", MX 7000, MX718A1 Upper Zone A, Lightbar, Code 3, 56", XL 5000, XL556A1 Upper Zone A, Lightbars (2), Code 3, 22", XL 5000, XL5100 Warning Lights, Additional (2), Upper Zone C, Whelen, 600 Series LED, Red Both Sides Warning Lights, Additional (2), Upper Zone C, Whelen, 600 Series LED, Red Driver, Amber Officer Warning Lights, Additional (2), Upper Zone C, Whelen, 600 Series LED, Red Driver, Blue Officer Warning Lights, Additional (2), Upper Zone C, Whelen, 700 Series LED, Red Both Sides Warning Lights, Additional (2), Upper Zone C, Whelen, 700 Series LED, Red Driver, Amber Officer Warning Lights, Additional (2), Upper Zone C, Whelen, 700 Series LED, Red Driver, Blue Officer Warning Lights, Additional (2), Upper Zone C, Whelen, 900 Series LED, Red Both Sides Warning Lights, Additional (2), Upper Zone C, Whelen, 900 Series LED, Red Driver, Amber Officer Warning Lights, Additional (2), Upper Zone C, Whelen, 900 Series LED, Red Driver, Blue Officer Warning Lights, Additional (2), Upper Zone C, Whelen, M6 Series LED, Red Both Sides Warning Lights, Additional (2), Upper Zone C, Whelen, M6 Series LED, Red (Clear Lens) Both Sides Warning Lights, Additional (2), Upper Zone C, Whelen, M6 Series LED, Red (Clear Lens) Driver, Amber (Clear Lens) Officer Warning Lights, Additional (2), Upper Zone C, Whelen, M9 Series LED, Red Both Sides Warning Lights, Additional (2), Upper Zone C, Whelen, M9 Series LED, Red (Clear Lens) Both Sides Warning Lights, Additional (2), Upper Zone C, Whelen, M9 Series LED, Red (Clear Lens) Driver, Amber (Clear Lens) Officer Warning Lights, Additional (2), Upper Zone C, Whelen, Micro Edge Freedom Strobe and Super-LED, Red Both Sides Lightbars (2), Above Rear Crew Doors, Whelen, FNMINI, Red Both Sides Lightbars (2), Above Rear Crew Doors, Whelen, FNMINI, Red Driver, Blue Officer Lightbars (2), Above Rear Crew Doors, Whelen, Mini Edge Ultra Freedom, Red Both Sides Lightbars (2), Above Rear Crew Doors, Whelen, Mini Edge Ultra Freedom, Red-White Both Sides Upper Zone C, Warning Lights (2), Whelen, 600 Series LED, Red Both Sides Upper Zone C, Warning Lights (2), Whelen, 600 Series LED, Red Driver, Amber Officer Upper Zone C, Warning Lights (2), Whelen, 600 Series LED, Red Driver, Blue Officer Upper Zone C, Warning Lights (2), Whelen, 700 Series LED, Red Both Sides Upper Zone C, Warning Lights (2), Whelen, 700 Series LED, Red Driver, Amber Officer Upper Zone C, Warning Lights (2), Whelen, 700 Series LED, Red Driver, Blue Officer Upper Zone C, Warning Lights (2), Whelen, 900 Series LED, Red Both Sides Upper Zone C, Warning Lights (2), Whelen, 900 Series LED, Red Driver, Amber Officer Upper Zone C, Warning Lights (2), Whelen, 900 Series LED, Red Driver, Blue Officer Upper Zone C, Warning Lights (2), Whelen, M6 Series LED, Red Both Sides Upper Zone C, Warning Lights (2), Whelen, M6 Series LED, Red (Clear Lens) Both Sides Upper Zone C, Warning Lights (2), Whelen, M6 Series LED, Red (Clear Lens) Driver, Amber (Clear Lens) Officer Upper Zone C, Warning Lights (2), Whelen, M9 Series LED, Red Both Sides Upper Zone C, Warning Lights (2), Whelen, M9 Series LED, Red (Clear Lens) Both Sides Upper Zone C, Warning Lights (2), Whelen, M9 Series LED, Red (Clear Lens) Driver, Amber (Clear Lens) Officer Tail Lights, LED, Whelen, M6 Series, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Casting Tail Lights, LED, Whelen, M6 Series, Stop-Tail (Combination)/Turn/Backup/Warning, 4-Light Vertical Casting Stabilizer Cover Warning Lights (2), Whelen, M6 Super LED, Red, Activated with Aerial Master Stabilizer Cover Warning Lights (4), Whelen, M6 Super LED, Red, Activated with Aerial Master Upper Zone A, Lightbar, Whelen, 55", Freedom LED, Flat Roof, 8 Red, 2 White (Fully Populated Front) Upper Zone A, Lightbar, Whelen, 60", Freedom LED, Raised Roof, 8 Red, 2 White (Fully Populated Front) Upper Zone A, Lightbar, Whelen, 72", Freedom LED, Flat Roof, 12 Red, 2 White (Fully Populated Front) Upper Zone A, Lightbar, Whelen, 72", Freedom LED, Raised Roof, 12 Red, 2 White (Fully Populated Front) Upper Zone A, Lightbar, Whelen, 82", Freedom LED, Raised Roof, 8 Red, 2 White Upper Zone A, Lightbar, Whelen, 82", Freedom LED, Raised Roof, 12 Red, 2 White (Fully Populated Front) Upper Zone A, Lightbars (2), Whelen, 24", Freedom LED, FNMINI, Red-Blue Upper Zone A, Lightbars (3), Whelen, Center Front Facing Mini Ultra Freedom (1), Angled FNMINI (2) Decals (2), Reflective, 14" Custom on Door Decals (2), Reflective, Custom on Door, Customer Supplied, OEM Installed Transfer Switch, Generator-to-Shoreline

001112 001114 001115 001151 001170 001200 001202 001204 001207 001210 001223 001224 001229 001230 001234 001236 001246 001247 001249 001252 001256 001271 001272 001273 001277 001278 001279 001287 001290 001291 001292 001293 001294 001295 001296 001297 001298 001299 000860 000861 000862 000864 000865 000866 000867 000868 000869 000870 000873 000874 000875 000876 000877 000879 000880 000882 000885 000886 000887 000890 000894 000895 000896 000897 000898 000899 000901 000902 000903 000907 000933 000934 000954 000955 000968 000969 000971 000980 000981 000986 000987 001017 001018 001019 001020 001023 001024 001025 001026 001027 001028 001029 001030 001031 001032 001033 001038 001076 001084 Storage Compartment, Rear Center Between Frame Rails with Painted Door Chevron, Front Bumper Face, Match Rear Chevron Chevron, Front Bumper Face, Match Rear Chevron Siren, Q2B, Federal Signal, Brake Controller, Partially-Recessed Turntable Work Lights, (4) On-Scene LED Lighting Activation, In Cab and On Pump Panel, 'FRONT SCENE', Rocker Switches Lighting Activation, In Cab and On Pump Panel, 'LEFT SCENE', Rocker Switches Lighting Activation, In Cab and On Pump Panel, 'RIGHT SCENE', Rocker Switches Lighting Activation, In Cab and On Pump Panel, 'REAR SCENE', Rocker Switches Lighting Activation, In Cab and On Pump Panel, 'REAR SCENE', Wired to Reverse, Rocker Switches Junction Box Option, Powder Coat Black Junction Box Option, Powder Coat Red Junction Box Option, Powder Coat White Junction Box Option, Powder Coat Yellow Air Horn Activation, Push Button on Turntable Control Console Steps, Auxiliary, (2) Total, (1) Each Running Board, Grip Strut Mounting Board, Back Wall of Compartment, Varnished Plywood Air Horns (2), Grover, 1512 Air Horn Activation, Lanyard, Single Control, Center Air Horn Activation, Foot Switch, Officer's Side Air Horn Activation, Foot Switch, Driver's Side Air Horn Activation, Push Button on Pump Panel, Driver's Side Siren Head, 200W, Code 3, 3692 Siren Head, 100W, Federal Signal, PA300 Siren Head, 100W/200W, Whelen, 295HFSA7, Remote Siren Head Siren Head, 100W/200W, Whelen, 295SLSA1, Self-Contained Head Siren Head, 200W, Code 3, 3672 Siren, Q2B, Federal Signal, Brake Controller, Pedestal Mount Speaker, (1), 100W, Dynamax, ES100, Flush Mounted Speaker, (1), 100W, Cast Products, ITB, Recess Mounted Mounting Board, Back Wall of Compartment, Line-X Plywood Traffic Advisor, Whelen, 8-Light, 5mm LED Low-Profile, TAL85, TACTLD1 Controller Pre-Connect Hose Bed Housing Coating, Black Line-X Compartment Finish, Line-X, Gray Paint Rims Primary Body Color Paint Rims Primary Body Color with Silver Trim Aerial Egress Paint, Red, PPG# FDGH-4353 Aerial Egress Paint, Safety Yellow, PPG# FDGH-81485 Platform Paint Color, White, PPG# FDGH-2185 Siren, Q2B, Federal Signal, Brake Controller, Fully-Recessed Nozzle, Electric, Akron SaberMaster 1500 GPM, 5178, 3-1/2" NH Upper Zone A, Lightbar, Whelen, 56", Justice LED, JE2NFPA, Flat Or Raised Roof, 8 Red, 2 White Upper Zone A, Lightbar, Whelen, 56", Justice LED, JE2NFPA, Flat Or Raised Roof, 4 Red, 4 Blue, 2 White Chassis Paint, OEM Repaint Cab Exterior, Single Tone, International, 2-Door Chassis Paint, OEM Repaint Cab Exterior, Single Tone, International, 4-Door Chassis Paint, OEM Repaint Cab Exterior, Single Tone, Freightliner, 2-Door Chassis Paint, OEM Repaint Cab Exterior, Single Tone, Freightliner, 4-Door Chassis Paint, OEM Repaint Cab Exterior, Two-Tone, NO Pinstripe, International, 2-Door Chassis Paint, OEM Repaint Cab Exterior, Two-Tone, Pinstripe, International, 2-Door Chassis Paint, OEM Repaint Hood Exterior, Two-Tone, Pinstripe, International, 2-Door Chassis Paint, OEM Repaint Hood Exterior, Two-Tone, Pinstripe, Freightliner, 2-Door Chassis Paint, OEM Repaint Cab Exterior, Two-Tone, Pinstripe, Freightliner, 2-Door Chassis Paint, OEM Repaint Cab Exterior, Two-Tone, Pinstripe, International, 4-Door Chassis Paint, OEM Repaint Cab Exterior, Two-Tone, NO Pinstripe, International, 4-Door Chassis Paint, OEM Repaint Hood Exterior, Two-Tone, Pinstripe, International, 4-Door Chassis Paint, OEM Repaint Hood Exterior, Two-Tone, Pinstripe, Freightliner, 4-Door Paint, Chassis Door Jams, Primary Body Color Touchup Paint, 2 Oz. Bottle Driveline Work, Split-Shaft Pump, Commercial Cab Bleeder Valve, Hale Pinstriping, Pumper, Gold Leaf, Engine-Turned 22kt Pinstriping, Aerial, Gold Leaf, Engine-Turned 22kt Crosslays, Above Front of Body, (3) 1-1/2" (Mid Mounts) Crosslays, Above Front of Body, (2) 1-1/2" and (1) 2-1/2" (Mid Mounts) Dump Valve Location, Inside Rear Compartment, Drain Pan Under Body Finish, Two-Step Undercoating Process Mud Flaps, Custom Chassis Crosslay Top Cover, Vinyl, C-Rail and Velcro Top Only, Red Wheel Chocks, (1) Pair, Zico SAC-44 and Bracket, OEM Installed Wheel Chocks, (1) Pair, Zico AC-32 and Bracket, OEM Installed Bag of Bolts Hard Suction Hose, (1), Firequip, 5" x 10' (OAL 10' 6"), Maxi-Flex PVC Hard Suction Hose, (1), Firequip, 6" x 10' (OAL 10' 6"), Maxi-Flex PVC Hose Bed, Rear Body, Painted Primary Body Color Finish, (85' MMP/100' MMP) Hard Suction Hose, (1), Firequip, 4" x 10' (OAL 10' 6"), Maxi-Flex PVC Hose Bed, Rear Body, Painted Primary Body Color Finish, (100' MMA) Hose Bed, Side, In Place of Officer's Side Cmpts, Painted Primary Body Color Finish Plug, NST, 2-1/2", South Park Cap, 4" NST, Vented Chrome, South Park Cap, 5" NST, Vented Chrome, South Park Cap, 6" NST, Vented Chrome, South Park Stacked Tips (Quad), Akron, 2499 (2-1/2" NH Inlet) SCBA Mounting, (1), Zico, Knock-Down Bracket, KD-UN-5-SF, with PHS Strap SCBA Mounting, (1), Zico, Knock-Down Bracket, KD-UN-6-SF, with PHS Strap SCBA Mounting, (1), Zico, Knock-Down Bracket, KD-UN-7-SF, with PHS Strap SCBA Mounting, (1), Zico, "C" Clips, Valve Up, N5.25

SCBA Mounting, (1), Zico, "C" Clips, Valve Up, N6.75

SCBA Mounting, (1), Zico, "C" Clips, Valve Up, N7.25

Ladder Storage, In Torque Box, Rear Mounts Ladder, (1), Duo-Safety, 10' Folding Attic with Brackets, 585-A Ladder, (1), Duo-Safety, 10' Folding Attic, 585-A Ladder, (1), Duo-Safety, 12' Roof, 775-A Ladder, (1), Duo-Safety, 14' Roof, 775-A Ladder, (1), Duo-Safety, 16' Roof, 875-A Ladder, (1), Duo-Safety, 20' Two-Section Extension, 900-A Ladder, (1), Duo-Safety, 24' Two-Section Extension, 900-A Ladder, (1), Duo-Safety, 28' Two-Section Extension, 1200-A Ladder, (1), Duo-Safety, 35' Two-Section Extension, 1200-A Ladder, (1), Duo-Safety, 35' Three-Section Extension, 1225-A

001488 001490 001491 001492 001493 001494 001495 001505 001507 001508 001509 001510 001511 001512 001513 001514 001515 001516 001551 001552 001571 001590 001594 001596 001597 001598 001603 001611 001614 001615 001627 001628 001630 001632 001635 001636 001637 001638 001300 001302 001303 001305 001306 001307 001308 001309 001314 001315 001316 001317 001320 001321 001322 001323 001324 001325 001326 001327 001360 001376 001377 001379 001382 001394 001407 001408 001412 001414 001417 001419 001420 001422 001423 001424 001432 001433 001434 001435 001436 001437 001438 001441 001442 001443 001444 001447 001450 001458 001459 001464 001479 001480 001481 001482 001483 001484 001485 001486 001487 Ladder, (1), Alco-Lite, 10' Folding Attic, FL-10 Ladder, (1), Alco-Lite, 14' Roof, PRL-14 Ladder, (1), Alco-Lite, 16' Roof, PRL-16 Ladder, (1), Alco-Lite, 24' Two-Section Extension, PEL-24 Ladder, (1), Alco-Lite, 28' Two-Section Extension, PEL-28 Ladder, (1), Alco-Lite, 35' Two-Section Extension, PEL-35 Ladder, (1), Alco-Lite, 35' Three-Section Extension, PEL3-35 Ladder Storage, In Torque Box, Mid Mounts Ladder Storage, In Torque Box, (2) Enclosed Compartments (55') Ladder Storage, In Torque Box, (2) Enclosed Compartments (75') Ladder Storage, In Torque Box, (2) Enclosed Compartments (85' RMP/105') Ladder Storage, In Torque Box, (2) Enclosed Compartments (100' RMP/125') Pike Pole, (1), Duo-Safety, 4' Fiberglass, Standard Hook, D-Handle, FP4D Pike Pole, (1), Duo-Safety, 6' Fiberglass, Standard Hook, FP6 Pike Pole, (1), Duo-Safety, 8' Fiberglass, Standard Hook, FP8 Pike Pole, (1), Duo-Safety, 10' Fiberglass, Standard Hook, FP10 Pike Pole, (1), Nupla, 4' Fiberglass, Standard Hook, Super Duty, D-Handle, SPDH-4 Pike Pole, (1), Nupla, 6' Fiberglass, Standard Hook, Super-Duty, SPD-6 Pike Pole, (1), Nupla, 8' Fiberglass, Standard Hook, Super-Duty, SPD-8 Pike Pole, (1), Nupla, 10' Fiberglass, Standard Hook, Super-Duty, SPD-10 OEM Chassis Preparations, Spartan Metro Star/Gladiator Switch Panel, Standard 12-Switch, Floor Console Switch Panel, Standard 12-Switch, Dash Heat Exchanger, Chassis Supplied and Installed Engine Compartment Light Overlay Below Windows, Rear Wall of Cab, Tread Plate Air Outlet, 1/4" Quick Connect Female, Driver's Side Pump Panel Air Outlet, 1/4" Quick Connect Female, Officer's Side Step Area Air Inlet/Outlet, With Specialized Compartment, 25' of Hose Map Console, 3-Slot, Engine Tunnel EMS Compartment, Center Back of Engine Tunnel EMS Compartment, Center Back Wall of Cab EMS Compartment, Outside of Forward Facing Seat on Driver's Side Dome Light, Red, 8" Front Bumper Extension, 21", Tread Plate Gravel Shield, IHC Front Bumper Extension, 21", Tread Plate Gravel Shield, Freightliner Wheel Covers, Stainless Steel, Simulator Kit, RealWheels, Single Axle Wheel Covers, Stainless Steel, Simulator Kit, RealWheels, Tandem Axle Wheel Covers, Stainless Steel, Trim Kit, Phoenix USA, Single Axle Wheel Covers, Stainless Steel, Trim Kit, Phoenix USA, Tandem Axle Wheel Covers, Stainless Steel, Hub and Lug Nut, RealWheels, Single Axle Wheel Covers, Stainless Steel, Hub and Lug Nut, RealWheels, Tandem Axle Insta Chain Air-Operated 6-Strand Tire Chains for Rockwell Suspension Onspot Air-Operated 6-Strand Tire Chains for Rockwell Suspension Onspot Air-Operated 6-Strand Tire Chains for Dana Suspension Rud Air-Operated 6-Strand Tire Chains for Spicer Suspension Chassis Step and Fuel Tank Overlays, Full, Tread Plate, International, 2-Door Chassis Step and Fuel Tank Overlays, Full, Tread Plate, International, 4-Door Floor Console, Center, Between Bucket Seats, Black Line-X Finish Ladder, (1), Duo-Safety, 20' Roof, 875-A Ladder, (1), Alco-Lite, 14' Combo, CJL-14 Aerial Maintenance Special Tools Construction and Dimensions, Rear Mount Ladder Structure (55') Construction and Dimensions, Rear Mount Ladder Structure (75') Construction and Dimensions, Rear Mount Ladder Structure (105') Construction and Dimensions, Rear Mount Ladder Structure (UT 100') Construction and Dimensions, Rear Mount Ladder Structure (125') Construction and Dimensions, Rear Mount Ladder Structure (100' SHD) Construction and Dimensions, Rear Mount Ladder Structure (85' RMP) Construction and Dimensions, Rear Mount Ladder Structure (100' RMP) Construction and Dimensions, Mid Mount Ladder Structure (85' MMP) Construction and Dimensions, Mid Mount Ladder Structure (100' MMA) Egress, Bolt-On, Standard (55') Egress, Bolt-On, Standard (75') Egress, Bolt-On, Standard (105') Egress, Bolt-On, Standard (UT 100') Egress, Bolt-On, Standard (125') Egress, Bolt-On, Standard (100' SHD) Folding Steps on Fly Section (55'/75'/105'/125') Ladder Travel Support/Cradle, LED Lights, Cradle Interlock System (55') Ladder Travel Support/Cradle, LED Lights, Cradle Interlock System (75') Ladder Travel Support/Cradle, LED Lights, Cradle Interlock System (85' RMP/105') Ladder Travel Support/Cradle, LED Lights, Cradle Interlock System (100' RMP/125') Ladder Travel Support/Cradle, LED Lights, Cradle Interlock System (85' MMP) Elevation System (55') Elevation System (75') Elevation System (85' RMP/105') Elevation System (100' RMP/125') Elevation System (85' MMP) Hose Bed, EHL, Black Line-X Finish (55') Hose Bed, EHL, Black Line-X Finish (75') Hose Bed Loading Light, (1) Front of Hose Bed, Halogen, Unity AG-R Stabilizer Work Lights (2), Signal Stat, 3711 LED, Clear Stabilizer Angle Level Gauges (2) Stabilizer 1" Auxiliary Pads (2) with Racks Below Body Stabilizer 1" Auxiliary Pads (4) with Racks Below Body Stabilizer 2" Auxiliary Pads (4) with Racks Below Body Ground Control System, Electric Over Hydraulic Controls, Front and Rear Stabilizers, Lower Center Rear, Horizontal, Brushed Stainless Doors Stabilizer Arm Warning Lights (4), Whelen, 5G Series Super LED, Red Ladder Hour Meter, At Turntable Platform Design/Construction/Deck Surface, Rear Mount Platform, Single Monitor Platform Equipment Storage Box (1) Platform Hose Storage Box (1), 50' of 2-1/2" Hose Platform Control Console, Traditional, (3) Control Levers Aerial Power Take-Off Hydraulic Pump with "Thru-Drive" (55') Hydraulic Pump with "Thru-Drive" (75'/105') Hydraulic Pump with "Thru-Drive" (85' MMP/85' RMP/100' RMP/125') Hydraulic System (55')

002205 002210 002216 002221 002230 002262 002263 002271 002272 002273 002274 002275 002288 002395 002397 002398 002399 002400 002401 002408 002409 002410 002412 002413 002415 002416 002417 002418 002427 002430 002431 002432 002433 002434 002453 002454 002455 002459 001639 001640 001641 001642 001643 001644 001645 001647 001648 001649 001650 001654 001658 001659 001660 001662 001663 001666 001667 001668 001695 001713 001715 001716 001717 001719 001720 001729 001731 001741 001805 001807 001809 001811 001817 001818 001837 001838 001850 001851 001852 001853 001854 001855 001856 001857 001858 001859 002132 002135 002154 002155 002170 002177 002178 002180 002181 002186 002187 002199 002203 Hydraulic System (75') Hydraulic System (105') Hydraulic System (125') Hydraulic System (85' RMP) Hydraulic System (100' RMP) Hydraulic System (85' MMP) Hydraulic System (100' MMA) Hydraulic Pressure Filter, 3 Micron (Platforms) Load Sensing System, Loadminder Display (Ladders) Emergency Hydraulic Pump (55'/75'/105') Emergency Hydraulic Pump, Extra Duty (125'/Platforms) Communication System, 2-Way, Turntable-Tip, Atkinson (55'/75'/105'/125') Communication System, 2-Way, Turntable-Tip, Atkinson (85' RMP) Communication System, 2-Way, Turntable-Tip, Atkinson (100' RMP) Communication System, 2-Way, Turntable-Tip, Atkinson (85' MMP) Communication System, 3-Way, Pump Panel-Turntable-Tip, Atkinson (55'/105'/125') Communication System, 3-Way, Pump Panel-Turntable-Tip, Atkinson (75') Communication System, 3-Way, Pump Panel-Turntable-Tip, Atkinson (85' RMP) Communication System, 3-Way, Pump Panel-Turntable-Tip, Atkinson (100' RMP) Communication System, 3-Way, Pump Panel-Turntable-Tip, Atkinson (85' MMP) Wheel Chocks, (1) Pair, Worden HRX, Shipped Loose Waterway Relief Valve / Drain Valve Waterway Inlet, Rear, 4" Inlet and 4" Plumbing (55') Waterway Inlet, Rear, 4" Inlet and 4" Plumbing (75') Waterway Inlet, Rear, 4" Inlet and 4" Plumbing (105') Waterway Inlet, Rear, 5" Inlet and 5" Plumbing (85' RMP/100' RMP/125') Waterway Inlet, Officer's Side, 4" Inlet and 4" Plumbing (100' MMA) Preconnect, In Platform, 1-1/2", NST (85' MMP/85' RMP/100' RMP) Nozzle, Electric, Akron Akromatic 1250 GPM, 5177 (2-1/2" NH) Nozzle, Electric, Elkhart X-Stream 1000 GPM, SM-1000E, 3-1/2" NH Aerial Angle Indicator, Base Section Aerial Extension Tape Axe Mounting Bracket (1), Fly Section, Bracket Only (Dealer/Customer Supplied Axes) Axe Mounting Bracket (1), In Platform, Bracket Only (Dealer/Customer Supplied Axes) Platform Rappelling Arm, 500 lb, Single Monitor Platform Rappelling Arm with Stokes, 500 lb Aerial Information Specification Plate Ladder Signs (2), On Base Section (55'/75') Egress, Bolt-On, Ferrara (55') Egress, Bolt-On, Short, Ferrara (Ladders) Egress, Bolt-On, Ferrara (75') Water Tank Fill Tower, UPF, Blue, Anti-Surge Egress, Bolt-On, Ferrara (105') Aerial Angle Indicator, Base Section and Platform Water Tank Fill Tower, UPF, Green, Anti-Surge Stabilizer Angle Level Gauges (2), Ferrara Turntable Control Console, Traditional, (3) Levers, OEMs, On-Scene LED Light Under Lid (Ladders) Water Tank Fill Tower, UPF, Yellow, Anti-Surge Platform Warning Lights (4), Whelen, 700 Series Super LED, Red Pump Compartment Internal Lighting, LED, Whelen Pressure Gauge, 3-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 Foam System, FoamPro, 2002, Dual System, Manual Selector, Class A and B Foam, Flush System Water Tank Level Display, Chassis Supplied 4-Light, Cab Sides, Class 1 Driver Water Tank Level Display, Whelen PSTANK, Cab Sides, Class 1 Driver Water Tank Level Display, Whelen PSTANK, Cab Sides, Rear of Body, Class 1 Driver Pressure Gauge, 2-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), Dual Scale -30-0-400 / -100-0-2800 Wheel Wells, Rear, Single Axle Wheel Wells, Rear, Tandem Axle Alarm, Back-Up, Ecco 510 Dba Crosslay Cover, Hinged Tread Plate, Top Mount Crosslay Cover, Hinged Bi-Fold Tread Plate Intake Relief Valve, Pump, Elkhart, Factory Preset Access Panel, Pump, Front Pump Module, Removable, Tread Plate, Compression Latches, Top Mounts Ladder Storage, Inside Body, Side of Water Tank, Officer's Side, Tread Plate Door Water Tank Drain, 1-1/2" Valve, Aerials Water Tank Level Display, Whelen PSTANK, Cab Sides, FRC Driver Water Tank Level Display, Whelen PSTANK, Cab Sides, Rear of Body, FRC Driver Pike Pole, (1), Akron, 4' Fiberglass, Standard Hook, Ultra-Lite, D-Handle, UL-4D Pike Pole, (1), Akron, 6' Fiberglass, Standard Hook, Ultra-Lite, UL-6 Pike Pole, (1), Akron, 8' Fiberglass, Standard Hook, Ultra-Lite, UL-8 Pike Pole, (1), Akron, 10' Fiberglass, Standard Hook, Ultra-Lite, UL-10 Pike Pole, (1), Akron, 12' Fiberglass, Standard Hook, Ultra-Lite, UL-12 Foam System, Waterous, Advantus 3, Single System, Class A Foam, NO Optional Flush System Rear Deck, Bolt-On, Recessed Back, Tread Plate, Split Depth Side(s) Generator Start, Remote, Diesel Gen., Onan, In Cab and on Pump Panel Generator Start, Remote, Diesel Gen., Onan, On Pump Panel Rear Deck, Bolt-On, Flat Back, Tread Plate, 13.25", Grip Strut Insert Rear Deck, Bolt-On, Flat Back, Tread Plate, 13.25", Bar Grate Insert Overlay, Tread Plate, Inside Facing Sides of Recessed Rear Sub-Frame, Hot-Dip Galvanized, Rear Frame Extension Sub-Assembly, RAGE Hard Suction Hose, (1), Firequip, 4" x 7' (OAL 7'), Maxi-Flex PVC Hard Suction Hose, (1), Firequip, 4" x 8' (OAL 8'), Maxi-Flex PVC Wheel Chocks, (1) Pair, Zico SAC-44 (Chocks Only) Wheel Chocks, (1) Pair, Zico SAC-44 and Bracket, Shipped Loose Wheel Chocks, (1) Pair, Cast Products, TMC1008-4 and Bracket, Shipped Loose Wheel Chocks, (1) Pair, Cast Products, TMC1008-4 (Chocks Only) Wheel Chocks, (1) Pair, Zico AC-32 (Chocks Only) Wheel Chocks, (1) Pair, Zico AC-32 and Bracket, Shipped Loose License Plate Bracket Portable Winch, Warn Industries, 9000 lb.

Receiver Tube, (1), Front Receiver Tube, (1), Rear Receiver Tubes, (2) Total, (1) Each Side Receiver Tubes, (2) Total, (1) Each Side Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - psi 0-400 - Blue LED Lit Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - psi 0-400 - Green LED Lit Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - psi 0-400 - White LED Lit Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - Dual Scale 0-400 / 0-2800 - Blue LED Lit

002645 002646 002647 002648 002649 002650 002651 002652 002657 002663 002691 002712 002714 002717 002720 002721 002724 002740 002742 002743 002745 002748 002749 002755 002770 002771 002772 002773 002781 002782 002783 002784 002785 002786 002787 002788 002789 002790 002460 002461 002468 002469 002470 002471 002472 002473 002474 002475 002476 002477 002482 002483 002484 002485 002487 002497 002499 002500 002502 002535 002536 002538 002540 002541 002543 002545 002549 002550 002553 002565 002566 002568 002570 002572 002574 002576 002579 002580 002581 002583 002585 002586 002587 002588 002589 002591 002593 002595 002598 002599 002604 002606 002614 002615 002616 002630 002634 002642 002643 Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - Dual Scale 0-400 / 0-2800 - Green LED Lit Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - Dual Scale 0-400 / 0-2800 - White LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - psi 0-400 - Red LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - psi 0-400 - Blue LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - psi 0-400 - Green LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - psi 0-400 - White LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - psi 0-400 - Yellow LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 - Red LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 - Blue LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 - Green LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 - White LED Lit Pressure Gauge, 2-1/2", Class 1, Liquid Filled - Dual Scale 0-400 / 0-2800 - Yellow LED Lit Foam System, Eductor, Akron, 3096 Bypass, 95 GPM, Class A, NO Optional Flush System Foam System, Eductor, Akron, 3126 Bypass, 125 GPM, Class A, NO Optional Flush System Foam System, Eductor, Elkhart, 240-95 Bypass, 95 GPM, Class A, NO Optional Flush System Foam System, Eductor, Elkhart, 240-125 Bypass, 125 GPM, Class A, NO Optional Flush System Foam System, Waterous, Advantus 6, Single System, Class A Foam, NO Optional Flush System Tray, (1), Adjustable-Height Roll Out, Austin Hardware, 300#, 100% Extension, Abraded, With Front Drawer Release Tray, (1), Floor-Mounted Roll Out, Austin Hardware, 300#, 100% Extension, Abraded, With Front Drawer Release Tray, (1), Adjustable-Height Roll Out, Austin Hardware, 300#, 100% Extension, Line-X, With Front Drawer Release Tray, (1), Floor-Mounted Roll Out, Austin Hardware, 300#, 100% Extension, Line-X, With Front Drawer Release Discharge, Front Bumper Officer-Side, 1-1/2", Above Gravelshield, NST Discharge, Front Bumper Officer-Side, 2-1/2", Above Gravelshield, NST (250 GPM) Discharge, Officer-Side, 2-1/2", NST (250 GPM) Preconnect, Hose Bed Driver-Side, 2-1/2", NST Discharge, Rear Officer-Side, 2-1/2", NST (250 GPM) Discharge, Rear Driver-Side, 2-1/2", NST (250 GPM) Discharge, Driver-Side, 2-1/2", NST (250 GPM) Discharge, Front Bumper Driver-Side, 1-1/2", Above Gravelshield, NST Discharge, Front Bumper Driver-Side, 2-1/2", Above Gravelshield, NST (250 GPM) Discharge, Officer-Side, 4", NST (625 GPM) Water Tank Fill Tower, UPF, Black, Anti-Surge Extender, Electric, Elkhart, 18", 3" NPT, 8598 Extender, Electric, Elkhart, 18", 3" Four Bolt Flange, 8598 Adapter, TFT, 3" NPT Inlet, Driver-Side, 2-1/2", Partially Recessed Extend-A-Gun, Manual, TFT, 12", XG12VL-PL Extend-A-Gun RC3, Electric, TFT, 12", XGA32VL-RL Inlet, Officer-Side, 2-1/2", Partially Recessed Inlet, Driver-Side, 3", Partially Recessed Extend-A-Gun, Manual, TFT, 12", XG12VL-XL Stacked Tips (Quad) and Stream Shaper, Elkhart, ST-194, 283A Stacked Tips (Triple) and Stream Shaper, Elkhart, ST-195, 283A Deck Gun, Manual, Akron Apollo 3426, Fixed Mount, 3" NPT Inlet Inlet, Officer-Side, 2-1/2", Fully Recessed Inlet, Driver-Side, 2-1/2", Fully Recessed Stacked Tips (Quad) and Stream Shaper, Akron, 2499, 3488 (2-1/2" NH Inlets) Stacked Tips (Quad), Elkhart, ST-191A Stacked Tips (Quad) and Stream Shaper, TFT, MST-4NJ, XF-SS10 (2-1/2" NH) Tips and Built-In Stream Shaper, TFT, YST-4NN Portable Ground Base, Elkhart, (2) 2-1/2" Inlets Mounting Bracket, Elkhart, Portable Ground Base Position Feedback, Akron, Position Indicator Position Feedback, Akron Panel Mount Controller, Addiitonal, Elkhart Body Striping, Aerial, Rollup Doors, 1"-6"-1", Low Angle Transition Portable Ground Base, TFT, (2) 2-1/2" Inlets, XFH-2NJ Body, 100" Wide, Custom Pumper, Single-Axle, Aluminum, 1/8" Body, 100" Wide, Custom Pumper, Single-Axle, Galvanneal, 12 Gauge Body, 100" Wide, Rear Mount Aerial, Single-Axle, Aluminum, 1/8" (55') Pump Module, Rear Mount Aerial, Independent, 1/8" Aluminum (55') Body, 100" Wide, Rear Mount Aerial, Single-Axle, Aluminum, 1/8" (75') Pump Module, Rear Mount Aerial, Independent, 1/8" Aluminum (75') Body, 100" Wide, Rear Mount Aerial, Tandem-Axle, Aluminum, 1/8" (75'/85' RMP/105') Pump Module, Rear Mount Aerial, Independent, 1/8" Aluminum (85' RMP/105') Pump Module, Rear Mount Aerial, Independent, 1/8" Aluminum (100' RMP/125') Body, 100" Wide, Rear Mount Aerial, Tandem-Axle, Aluminum, 1/8" (100' RMP/125') Body, 100" Wide, Mid Mount Aerial, Tandem-Axle, Aluminum, 1/8" (85' MMP/100' MMP/100' MMA) Pump Module, Mid Mount Aerial, Independent, 1/8" Aluminum (85' MMP/100' MMP) Sub Frame, GS-36, Hot-Dip Galvanized Steel, Aerial (75' Tandem-Axle) Fuel Fill, Fire Shopp Painted Door, Driver's Side Body, 100" Wide, Custom Pumper, Single-Axle, Aluminum, 3/16" Handrail, Pump Module, Above Pump Panel, Vertical, Driver's Side, Knurled Stainless Steel Ladder Storage, Inside Body, Side of Water Tank, Officer's Side, Painted Aluminum Door Ladder Storage, Above Low Sides, Officer's Side, OEM Brackets Handrails, Pump Module, Vertical, Entrance of Walkway, Both Sides, Stainless Steel Handrail, Body (Rear), Above Dump Valve Step and Below Hose Bed, Horizontal, Knurled Aluminum Fuel Fill, Fire Shopp Painted Door, Officer's Side Shelf, (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Abraded Shelf, (1), Adjustable, Aluminum, Full Depth (4 Struts), Abraded Shelf, (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Line-X Shelf, (1), Adjustable, Aluminum, Full Depth (4 Struts), Line-X Shelf, (1), Permanent, Aluminum, Shallow Depth, Matching Compartment Finish Shelf, (1), Permanent, Aluminum, Full Depth, Matching Compartment Finish Light Tower Option, Command Light, Back-Light Clearance Lights, Grote and Truck-Lite, LED, Red (55'/75'/105') Clearance Lights, Grote and Truck-Lite, LED, Red (100' RMP/125') Generator, Gas, Honda, 11hp, EM5000SXK3AT Generator, Gas, Honda, 13hp, EM6500SXK2AT Generator Start, Remote, Hydraulic Gen., In Cab and Next to Load Center Generator Start, Remote, Hydraulic Gen., In Cab and on Pump Panel Generator Location, Above Pump Module, Harrison Generator Location, Above Pump Module, Onan Generator Location, Above Pump Module, Smart Power Generator Location, Ahead of Turntable, Harrison Generator Location, Ahead of Turntable, Onan Generator Location, Ahead of Turntable, Smart Power Generator Location, Front of Body, Harrison Generator Location, Front of Body, Onan

002936 002938 002939 002940 002941 002942 002955 002956 002971 002992 002993 002994 003011 003109 003110 003111 003120 003142 003166 003167 003168 003465 003469 003470 003471 003477 003478 003479 003496 003506 003507 003552 003558 003559 003560 003564 003565 003572 002791 002792 002793 002794 002797 002798 002799 002800 002801 002802 002803 002804 002805 002806 002807 002808 002809 002816 002817 002818 002833 002834 002841 002842 002843 002844 002845 002848 002849 002850 002851 002852 002853 002854 002855 002857 002860 002871 002872 002873 002874 002875 002878 002879 002880 002911 002912 002913 002914 002915 002916 002917 002927 002928 002929 002930 002931 002932 002933 002934 002935 Generator Location, Front of Body, Smart Power Anodes, Waterous, Zinc, 2 Discharge, 2 Intake Anodes, Hale, Alloy, 2 Discharge, 2 Intake Anodes, Hale, Magnesium, 2 Discharge, 2 Intake Generator, Hydraulic, Smart Power, 6kW, HR-6, Command and Control Center Generator, Hydraulic, Smart Power, 15kW, HR-15, Command and Control Center Handrail, Pump Module, Above Pump Panel, Horizontal, Driver's Side, Knurled Stainless Steel Handrail, Pump Module, Above Pump Panel, Horizontal, Officer's Side, Knurled Stainless Steel Handrail, Body (Front), Top, Driver's Side, Knurled Stainless Steel Handrail, Body (Front), Top, Officer's Side, Knurled Stainless Steel Handrail, Body (Rear), Rear Face, Vertical, Driver's Side, Knurled Stainless Steel Handrail, Body (Rear), Rear Face, Vertical, Officer's Side, Knurled Stainless Steel Handrail, Body (Rear), Above Compartment and Below Hose Bed, Horizontal, Knurled Stainless Steel Handrail, Body (Rear), Above Dump Valve Step and Below Hose Bed, Horizontal, Knurled Stainless Steel Handrail, Body (Rear), Hose Bed Riser, Vertical, Driver's Side, Knurled Stainless Steel Handrail, Body (Rear), Hose Bed Riser, Vertical, Officer's Side, Knurled Stainless Steel Handrails, Body (Rear), Hose Bed Cover, Horizontal, Stainless Steel Handrail, Pump Module, Above Pump Panel, Vertical, Officer's Side, Knurled Stainless Steel Handrail, Pump Module, Top, Horizontal, Driver's Side, Knurled Stainless Steel Handrail, Pump Module, Top, Horizontal, Officer's Side, Knurled Stainless Steel Hose Bed Loading Light, (1) Rear, Halogen, Collins, CD-FX-12 Hose Bed Loading Light, (1) Rear, Halogen, Collins, CD-FX-9 Tail Lights, LED, Whelen, 600 Series, Stop-Tail (Separate)/Turn, 3-Light Vertical Casting Tail Lights, LED, Whelen, 600 Series, Stop-Tail (Separate)/Turn/Warning, 4-Light Vertical Casting Tail Lights, LED/Incandescent Backup, Weldon, 3884, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Casting Tail Lights, LED, Federal Signal, QuadraFlare, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Casting Tail Lights, LED, Federal Signal, QuadraFlare, Stop-Tail (Combination)/Turn/Backup/Warning, 4-Light Vertical Casting Tail Lights, LED, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Casting Tail Lights, LED, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup/Warning, 4-Light Vertical Casting Tail Lights, LED/Halogen Backup, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Casting Tail Lights, LED/Halogen Backup, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup/Warning, 4-Light Vertical Casting Tail Lights, LED/Halogen Backup, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup/Warning, Dual 2-Light Vertical Castings Tail Lights, LED/Halogen Backup, Whelen, 900 Series, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Individual Bezels Upper Zone A, Lightbar, Federal Signal, 8-Pod, Viewpoint SL LED, 535NFPA8P2 Upper Zone A, Lightbar, Code 3, 82", Defender LED, DF82ANFPA1 Traffic Advisor, Whelen, 8-Light, TIR6 LED Split, TA4437M, TACTLD1 Controller Upper Zone A, Lightbar, Whelen, 82", Freedom LED, Raised Roof, 6 Red, 2 White Hose Bed Loading Light, (1) Rear, LED, Whelen, PAR 36 Round Floodlight, Black Housing Scene Light, (1), 12V, FRC, Recessed, Halogen Focus 150W Scene Light, (1), 12V, FRC, Recessed, Halogen Focus 300W Scene Light, (1), 12V, FRC, Recessed, HID Optimum 70W Scene Light, (1), 12V, FRC, Recessed, HID Optimum 150W Lighting Activation, In Cab, 'LEFT SCENE', Rocker Switch Lighting Activation, In Cab, 'REAR SCENE', Rocker Switch Lighting Activation, In Cab, 'RIGHT SCENE', Rocker Switch Scene Light, (1), 120V, FRC, Recessed, Halogen Optimum 500W Scene Light, (1), 120V, FRC, Recessed, Halogen Optimum 750W Scene Light, (1), 240V, FRC, Recessed, Halogen Optimum 1500W Scene Light, (1), 120V, FRC, Telescoping Side Mount Pull-Up, Halogen Focus 750W Scene Light, (1), 120V, FRC, Telescoping Side Mount Pull-Up, Halogen Optimum 750W Scene Light, (1), 120V, FRC, Telescoping Side Mount Pull-Up, Halogen Focus 1000W Scene Light, (1), 120V, FRC, Telescoping Side Mount Pull-Up, Halogen Optimum 1000W Foam Tank, Pro Poly, Imperial Gallon, 20 Foam Tank, UPF, Imperial Gallon, 30 Foam Tank Level Gauge, Class 1 Intelli-Tank Gauge, Class A Foam Foam Tank Level Gauge, Class 1 Intelli-Tank Gauge, Class B Foam Water Tank Level Gauge, FRC Tankvision, Pump Operator's Panel, Officer's Side Pump Panel Water Tank Level Gauge, FRC Tankvision, Pump Operator's Panel, Rear Body Scene Light, (1), 120V, FRC, Telescoping Side Mount Push-Up, LED Spectra 20,000 Lumen Water Tank Level Display, Whelen PSTANK, Rear of Body, Class 1 Driver Water Tank Level Display, Whelen PSTANK, Rear of Body, FRC Driver Water Tank Level Display, Whelen TIR3, Cab Sides, Class 1 Driver Water Tank Level Display, Whelen TIR3, Cab Sides, FRC Driver Water Tank Level Display, Whelen TIR3, Driver's Side Cab, Class 1 Driver Water Tank Level Display, Whelen TIR3, Driver's Side Cab, FRC Driver Water Tank Level Display, Whelen TIR3, Cab Sides, Rear of Body, Class 1 Driver Water Tank Level Display, Whelen TIR3, Cab Sides, Rear of Body, FRC Driver Electrical System, Pumper, Weldon V-MUX Multiplex, QL-12 Harnesses, Sealed Switches Electrical System, Aerial, Weldon V-MUX Multiplex, QL-12 Harnesses, Sealed Switches Search Light, Golight 2020, Permanent Mount and (1) Remote Control Pike Pole, (1), Duo-Safety, 12' Fiberglass, Standard Hook, FP12 Ladder, (1), Duo-Safety, 14' Combo, 35-B Ladder, (1), Duo-Safety, 14' "Fresno" Attic Extension, 701 Nozzle, Electric, TFT MasterStream 1250 GPM, M-ERP1250-NN (3-1/2" NH) Water Tank Level Gauge, FRC Tankvision, Pump Operator's Panel Foam Tank Level Gauge, FRC Tankvision, Class A Foam Foam Tank Level Gauge, FRC Tankvision, Class B Foam Traffic Advisor, Whelen, 6-Light, 5mm LED Low-Profile, TAL65, TACTLD1 Controller Handrail, Pump Module, Top, Horizontal, Officer's Side, Knurled Aluminum Nozzle, Electric, TFT MasterStream 2000 GPM, M-ERP2000-NN (3-1/2" NH) Platform Marker Lights, Rear Mounts Nozzle Safety Chain Cap, NPSH, 1-1/2", Chrome, South Park Plug, BCT, 2-1/2", South Park Plug, AMA, 2-1/2", South Park Plug, CSA, 2-1/2", South Park Search Light, Golight 2020, Permanent Mount and (2) Remote Controls Barrel Strainer, Kochek 6" Drip Tray, Rollup Door, OEM Manufactured, Load Center Compartment Fol-da-Tank, 3000 Gallon, 22 oz. HPR, Steel Frame Hose Bed, EHL, Black Line-X Finish (85' RMP/105'/125'/RMP) Rear Step, Above Rear Compartment, Full-Width Grip-Strut Nozzle, Electric, Elkhart X-Stream 1250 GPM, SM-1250E, 3-1/2" NH Rear Deck, Bolt-On, Flat Back, Tread Plate, 13.25" Fenderettes, (2), Single Axle, Stainless Steel Fenderettes, (4), Tandem Axle, Stainless Steel Discharge (1), In Platform, 2-1/2", NST (Single Monitor Platforms) Discharges (2), In Platform, 2-1/2", NST (Single Monitor Platforms) Foam Tank, UPF, U.S. Gallon, 100

004651 004672 004674 004675 004676 004677 004678 004679 004697 004709 004731 004751 004772 004774 004776 004777 004779 004855 004863 004882 004883 004887 004889 004901 004902 004904 004905 004916 004917 004919 004920 004921 004929 004931 004932 004935 004939 004940 003582 003589 003598 003608 003609 003616 003619 003620 003621 003622 003623 003624 003635 003659 003695 003715 003717 003729 003730 003732 003733 003735 003737 003743 003744 003749 003752 003770 003787 003788 003798 003800 003802 003809 003820 003821 003835 003837 003852 003855 003878 003957 003987 003989 004096 004098 004105 004241 004326 004475 004476 004479 004522 004523 004557 004573 004583 004591 004595 004616 004649 Insight Ultimate, Fire Research - 4" Valve Size Water Tank Level Gauge, Class 1 Intelli-Tank, Pump Operator's Panel Handrail, Body (Front), Top, Driver's Side, Knurled Aluminum Tool Board, (1), Slide Out Aluminum, Full Height, Full Depth, Abraded Tool Board, (1), Slide Out Aluminum, Full Height, Full Depth, Line-X Scene Light, (1), 120V, Chassis Supplied, Brow (Wiring Only) Chevron Layout, Rear Body Surface, T1 Rolup Door, Tread Plate Storage Doors Chevron Layout, Rear Body Surface, Painted Storage Doors, EXCLUDE T1 Chevron Layout, Outboard Vertical Portion of Recessed Back, Painted Storage Doors Chevron Layout, Rear Body Surface, T1 Lap Door, EXCLUDE Tread Plate Storage Doors Chevron Layout, Center Portion of Recessed Back, T1 Rollup Door, Painted Storage Doors Chevron Layout, Center Portion of Recessed Back, T1 Lap Door, Painted Storage Doors Speaker, (1), 100W, Cast Products, Compact, Recess Mounted Pump Panel Lighting, Side Panels, LED, On-Scene Night Axe Brake Light, Additional, Whelen 700 Series LED Waterway Inlet, Officer's Side, 4" Inlet and 4" Plumbing (75') Waterway Inlet, Officer's Side, 4" Inlet and 4" Plumbing (105') Communication System, 3-Way, Pump Panel-Turntable-Tip, Atkinson (100' MMP) Communication System, 2-Way, Turntable-Tip, Atkinson (100' MMP) Hydraulic System (100' MMP) Hydraulic Pump with "Thru-Drive" (100' MMP) Platform Marker Lights, Mid Mounts Stabilizer Work Lights (4), Signal Stat, 3711 LED, Clear Construction and Dimensions, Mid Mount Ladder Structure (100' MMP) Ladder Travel Support/Cradle, LED Lights, Cradle Interlock System (100' MMP) Elevation System (100' MMP) Platform Design/Construction/Deck Surface, Mid Mount Platform, Single Monitor Reservoir Isolation Kit Aerial Monitor, Manual, Elkhart, Scorpion 8294-02 Nozzle, Manual, Elkhart X-Stream 1250 GPM, SM-1250, 3-1/2" NH Generator, Hydraulic, Onan, 6kW, 6RBAB, Onan Display Generator, Hydraulic, Onan, 8kW, 8RBAB, Onan Display Generator, Hydraulic, Onan, 10kW, 10RBAB, Onan Display Nozzle, Electric, Elkhart X-Stream 1500 GPM, SM-1500E, 3-1/2" NH Platform Striping, Reflective, Straight Across Waterway Inlet, Officer's Side, 5" Inlet and 5" Plumbing (85' MMP/100' MMP) Upper Zone A, Lightbar, Code 3, 69", MX 7000, MX769A1 Thermal Relief Valve (TRV), Hale, With Lights Water Tank Mounting, UPF, 75' Aerial Light Tower Shield on Chassis, Painted Upper Chassis Color Pump Panel Lighting Activation, ON/OFF Switch on Pump Panel Air Chuck Blow-Out, Booster Reel, Driver's Side Pump Panel Water Tank Level Gauge, Class 1 Intelli-Tank, Pump Operator's Panel, Rear Body Booted Cover Over Water Tank, Tread Plate Water Tank Overflow, UPF, 6", Pumpers w/o EHL Water Tank Drain, 1-1/2" Valve, Volunteer, Valve Handle Extension Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), psi -30-0-400 Air Horn Activation, Steering Wheel, Electric Horn / Air Horn Selection Switch Air Bottle Storage Tube, (1), Aluminum, In Compartment Hose Bed Cover, Vinyl, Top Bungee Hose Bed Cover, Vinyl, Top Button Snaps, Middle Button Snaps, Rear Footman Loop / J-Hook Scene Light, (1), 240V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 1000W Rub Rail Striping, 2", Silver, Reflective, Pumper Rub Rail Striping, 2", Silver, Reflective, Aerial Crosslay End Covers, Webbing, Sides Over Rollers with Velcro Center Nozzle, Electric, Akron SaberMaster 2000 GPM, 5178, 3-1/2" NH Tray, (1), Bi-Directional Roll Out, Innovative Ind., 1000#, 70% Extension, Line-X Ladder, (1), Duo-Safety, 18' Roof, 875-A USB Port, Weldon V-Mux Transceiver Kit Nozzle Clip, Booster Reel Drainage Cross Tube Discharge (1), Ladder Tip, 2-1/2", NST Tray, (1), Adjustable-Height Tilt Down, On-Scene, 250#, Line-X Tray, (1), Floor-Mounted Roll Out, On-Scene, 1000#, 100% Extension, Line-X Tray, (1), Floor-Mounted Roll Out, On-Scene, 1000#, 100% Extension, Abraded Tray, (1), Floor-Mounted Roll Out, On-Scene, 1000#, 70% Extension, Line-X Tray, (1), Floor-Mounted Roll Out, On-Scene, 1000#, 70% Extension, Abraded Tray, (1), Bi-Directional Roll Out, On-Scene, 1000#, 70% Extension, Abraded Tray, (1), Bi-Directional Roll Out, On-Scene, 1000#, 70% Extension, Line-X Turn Signals, (2) in Wheel Well Area, LED, Whelen, 700 Series Struts, (2), Horizontal, Back Wall of Compartment, Stainless Steel Pump Compartment Internal Lighting, LED, On-Scene Water Tank, Pro-Poly, 300 U.S. Gallons Auxiliary Vent, Pro Poly Water Tank Fill Tower, Pro-Poly, Black, Anti-Surge Water Tank Overflow, Pro-Poly, 4" Water Tank Overflow, Pro-Poly, 6", Pumpers w/ EHL, Aerials Dump Valve Tank Flange, Pro-Poly Mounting Board, Back Wall of Compartment, PAC Trac Hose Bed, EHL, Black Line-X Finish Camera System, Back-Up, Chassis Supplied, OEM Installed Sight Rods, Front Bumper Corners, Chrome Plated Lighting Activation, In Cab, 'REAR SCENE', Wired to Reverse, Rocker Switch Generator, Hydraulic, Onan, 15kW, 15RBAB, Onan Display Outlet Bar, 120V, (6) Receptacles, 5-15R Household, Wired to Shoreline Lighting Activation, On Pump Panel, Individually Switched Light Lighting Activation, In Cab, Individually Switched Light Lighting Activation, In Cab and On Pump Panel, Individually Switched Light Scene Light, (1), 120V, FRC, Recessed, Halogen Focus 1000W Scene Light, (1), 240V, FRC, Recessed, Halogen Focus 1000W Upper Zone A, Lightbars (2), Whelen, 24", Freedom LED, FNMINI Upper Zone A, Lightbar, Whelen, 72", Freedom LED, Flat Roof, 6 Red, 2 White Upper Zone A, Lightbar, Whelen, 72", Freedom LED, Raised Roof, 6 Red, 2 White Access Panel for Fuel Tank Gauge, Pumpers Refill System, FoamPro, Power-Fill, Single System Refill System, FoamPro, Power-Fill, Dual System Drip Tray, Rollup Door, ROM, Load Center Compartment Interior Cab Door Striping, White Reflective, 2-Door Interior Cab Door Striping, White Reflective, 4-Door

005566 005577 005579 005581 005582 005583 005584 005585 005586 005587 005588 005596 005597 005600 005612 005619 005623 005624 005625 005626 005627 005628 005629 005630 005631 005632 005633 005638 005639 005640 005646 005648 005649 005651 005652 005653 005654 005656 004947 004948 004949 005026 005048 005055 005060 005069 005071 005073 005084 005085 005090 005091 005092 005109 005110 005118 005119 005135 005136 005143 005144 005149 005152 005153 005154 005155 005158 005179 005183 005203 005222 005223 005234 005235 005236 005237 005238 005239 005241 005242 005257 005353 005367 005457 005460 005461 005516 005520 005526 005537 005538 005539 005541 005543 005544 005546 005548 005550 005565 Traffic Advisor, Whelen, 8-Light, TIR6 LED Low-Profile, TAM85, TACTLD1 Controller Traffic Advisor, Whelen, 6-Light, TIR6 LED Low-Profile, TAM65, TACTLD1 Controller Wheel Chocks, (1) Pair, Cast Products, TMC1008-4 and Bracket, OEM Installed Tray, (1), Bi-Directional Roll Out, Innovative Ind., 1000#, 70% Extension, Abraded Siren Head, 200W, Federal Signal, PA4000 Pump Color and Intakes Primary Body Color Chevron Layout, Rear Body Surface, T1 Rollup Door, EXCLUDE Tread Plate Storage Doors Nozzle, Manual, Akron Akromatic 1250 GPM, 5160 (2-1/2" NH) Ladder, (1), Duo-Safety, 8'/13' Combo, 300-A Ladder, (1), Duo-Safety, 12' Folding Attic, 585-A Battery Jumper Studs, Commercial Cab Foam Tank, Pro Poly, U.S. Gallon, 30 Mirror, Front Look-Down, Bus-Style, Officer's Side Fire Extinguisher, DOT Requirement Road Safety Kit, DOT Requirement Waterway Inlets, Driver's and Officer's Side, 4" Inlet and 4" Plumbing (100' MMA) Waterway Inlets, Driver's and Officer's Side, 5" Inlet and 5" Plumbing (85' MMP/100' MMP) Rub Rails, "C" Channel Design Sub-Frame, GS-36, Hot-Dip Galvanized, Custom Pumpers, Aluminum and Galvaneal Bodies Foam System, FoamPro, 3012 (Hydraulic), Single System, Class A Foam, NO Optional Flush System Foam System, FoamPro, 3012 (Hydraulic), Dual System, Class A and B Foam, Flush System Water Tank Mounting, Pro-Poly, Aerials Rear Step, Below Hose Bed, Full-Width Tread Plate Access Panel, Pump, Front Pump Module, Removable, Tread Plate, Compression Latches, Side Mounts, RMA's Enclosed Pump Panel Door, (1) ROM Roll-Up Door Construction, Painted Door Only Enclosed Pump Panel Door, (1) ROM Roll-Up Door Construction, Painted Door, Sills, and Tracks Rear Deck, Bolt-On, Recessed Back, Tread Plate, Full Depth Sides Stainless Steel Screws Handrail, Body (Rear), Rear Face, Vertical, Officer's Side, Knurled Aluminum Camera System, Back-Up, ASA Audiovox, Dual Generator, Hydraulic, Harrison, 15kW, MPC, FRC Frog Display Upper Zone A, Lightbars (2), Code 3, 18", 2100 LED, 2118NFPA2 Fol-da-Tank, 2100 Gallon, 22 oz. HPR, Steel Frame Fol-da-Tank, 2500 Gallon, 22 oz. HPR, Steel Frame Pike Pole, (1), Nupla, 12' Fiberglass, Standard Hook, Super-Duty, SPD-12 Pike Pole, (1), Nupla, 4' Fiberglass, Standard Hook, Light-Weight, D-Handle, YPDH-4 Pike Pole, (1), Nupla, 6' Fiberglass, Standard Hook, Light-Weight, YPD-6 Pike Pole, (1), Nupla, 8' Fiberglass, Standard Hook, Light-Weight, YPD-8 Pike Pole, (1), Nupla, 10' Fiberglass, Standard Hook, Light-Weight, YPD-10 Pike Pole, (1), Nupla, 12' Fiberglass, Standard Hook, Light-Weight, YPD-12 OEM Chassis Preparations, Sirius Access Panel for Fuel Tank Gauge, Aerials Nozzle, Manual, Elkhart X-Stream 1000 GPM, SM-1000, 3-1/2" NH Upper Zone C, Warning Lights (2), Whelen, Micro Edge Series LED, Red/Red Extend-A-Gun, Manual, TFT, 18", XG18VL-XL, For Crossfire Monitor Plug, NST, 3", South Park Cap, NST, 2-1/2", Chrome, South Park Cap, NST, 3", Chrome, South Park Aerial Monitor, Electric, TFT, Monsoon RC Y4-E21A-L (Ladders) Foam Tank, Pro Poly, U.S. Gallon, 20 Generator, Hydraulic, Smart Power, 10kW, HR-10, Command and Control Center Foam Tank, Pro Poly, U.S. Gallon, 40 Cap, 4" NST, Vented Chrome, Trident Cap, 5" NST, Vented Chrome, Trident Foam Tank, Pro Poly, U.S. Gallon, 50 Cap, 6" NST, Vented Chrome, Trident Piston Intake Valve, 5" NST x 4" Storz, Kochek, Air Bleeder Piston Intake Valve, 6" NST x 4" Storz, Kochek, Air Bleeder Piston Intake Valve, 5" NST x 5" Storz, Kochek, Air Bleeder Piston Intake Valve, 6" NST x 5" Storz, Kochek, Air Bleeder Foam System, FoamPro, 2001, Dual System, Electronic Selector, Class A and B Foam, Flush System Foam System, FoamPro, 2002, Dual System, Electronic Selector, Class A and B Foam, Flush System Battery Charger, 12V Shoreline Receptacle Battery Charger/Compressor, Kussmaul Pump Plus 1200 Battery Charger, Dual Pro Power Charger Display, Dual Pro Power Battery Charger, Three Bank Pro Power Charger Display, Three Bank Pro Power Super Auto Eject, Kussmaul, 15 Amp, 091-55-15-120 Super Auto Eject, Kussmaul, 20 Amp, 091-55-20-120 Super Auto Eject, Kussmaul, 30 Amp, 091-159-30-120 Shorline Receptacle, Manual Eject, 20 Amp, 125V Under Body Finish, Painted, Pumper Under Body Finish, Painted, Aerial Compressor, 120V, Kussmaul Butterfly Valve, Side Steamer, 6" Manual, Waterous Monarch Butterfly Valve, Side Steamer, 6" Manual, Neles Jamesbury Pike Pole, (1), Nupla, 4' Fiberglass, Roof Vent/Rubbish Hook, D-Handle, RH-4DA Pike Pole, (1), Nupla, 4' Fiberglass, Ceiling/Wall Hook, D-Handle, CWH-4YDA Pike Pole, (1), Nupla, 6' Fiberglass, Standard Hook, Light-Weight, D-Handle, YPDH-6 Pike Pole, (1), Nupla, 6' Fiberglass, Roof Vent/Rubbish Hook, D-Handle, RH-6D Pike Pole, (1), Nupla, 6' Fiberglass, Roof Vent/Rubbish Hook, Aluminum D-Handle, RH-6DA Pike Pole, (1), Nupla, 6' Fiberglass, Ceiling/Wall Hook, D-Handle, CWH-6YDA Pike Pole, (1), Nupla, 18' Fiberglass, Standard Hook, Light-Weight, YPD-18 Pike Pole, (1), Nupla, 18' Fiberglass, Roof Vent/Rubbish Hook, D-Handle, RH-18DA Scene Light, (1), 120V, FRC, Brow Mount, Halogen Focus 500W Scene Light, (1), 120V, FRC, Brow Mount, Halogen Focus 750W Scene Light, (1), 120V, FRC, Brow Mount, Halogen Focus 1000W Scene Light, (1), 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Focus 750W Scene Light, (1), 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 500W Scene Light, (1), 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 1000W Scene Light, (1), 240V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 1500W Scene Light, (1), 12V, FRC, Brow Mount, HID Focus 150W Scene Light, (1), 12V, FRC, Brow Mount, HID Optimum 150W Scene Light, (1), 12V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 300W Scene Light, (1), 12V, FRC, Telescoping Top Mount Pull-Up, HID Optimum 150W Scene Light, (1), 12V, FRC, Telescoping Thru The Roof Push-Up, HID Optimum 150W Scene Light, (1), 12V, FRC, Telescoping Side Mount Push-Up, HID Optimum 150W Scene Light, (1), 120V, FRC, Brow Mount, Halogen Optimum 1000W

006229 006234 006245 006261 006289 006290 006291 006292 006293 006294 006296 006297 006298 006299 006300 006301 006302 006303 006368 006369 006373 006374 006375 006379 006518 006588 006603 006604 006605 006608 006609 006617 006618 006634 006635 006637 006643 006644 005657 005658 005664 005665 005666 005667 005668 005669 005672 005676 005678 005689 005694 005725 005737 005740 005741 005743 005744 005745 005746 005747 005758 005772 005777 005782 005848 005849 005850 005853 005854 005876 005885 005887 005907 005908 005943 005968 005978 006008 006009 006010 006015 006016 006083 006089 006091 006119 006130 006144 006146 006149 006151 006156 006161 006162 006164 006172 006176 006205 006207 Scene Light, (1), 120V, FRC, Brow Mount, Halogen Optimum 500W Scene Light, (1), 120V, FRC, Brow Mount, Halogen Optimum 750W Scene Light, (1), 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 750W Scene Light, (1), 120V, FRC, Telescoping Thru The Roof Push-Up, Halogen Optimum 1000W Scene Light, (1), 120V, FRC, Telescoping Thru The Roof Push-Up, Halogen Optimum 500W Scene Light, (1), 120V, FRC, Telescoping Thru The Roof Push-Up, Halogen Optimum 750W Scene Light, (1), 120V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 1000W Scene Light, (1), 120V, FRC, Telescoping Side Mount Push-Up, Halogen Optimum 500W Scene Light, (1), 240V, FRC, Brow Mount, Halogen Optimum 1500W Scene Light, (1), 240V, FRC, Telescoping Side Mount Push-Up, Halogen Optimum 1500W Siren, Screaming Eagle, Eagle Sirens, Pedestal Mount Upper Zone A, Lightbar, Whelen, 82", Freedom LED, Flat Roof, 6 Red, 2 White Foam Tank, Pro Poly, U.S. Gallon, 100 Sign, Reflective, Rear Lap Door, 'Keep Back 150 Metres' Dump Valve Tank Flange, UPF Rear Step, Below Hose Bed, Tread Plate Rear Step, Below Hose Bed, Grip-Strut Scene Light, (1), 12V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 150W Scene Light, (1), 120V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 500W Scene Light, (1), 120V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 750W Scene Light, (1), 120V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 1000W Tow Option, Rear, Tow Eyes, Two (2) Chrome, on Full Length Frame Rail Hose Bed Drip Rail, Side Hose Bed Generator, Hydraulic, Smart Power, 8kW, HR-8, Command and Control Center Enclosed Pump Panel Door, (1) Amdor Roll-Up Door Construction, Painted Finish Flashlight, (1), Streamlight, LiteBox, 20 Watt, Orange, 45102, Vehicle Mount System Pump Color Painted Gray - Intakes Primary Body Color Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - psi 0-400 Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - psi 0-400 - Red LED Lit Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - Dual Scale 0-400 / 0-2800 Pressure Gauge, 2-1/2", Thuemling, Liquid Filled - Dual Scale 0-400 / 0-2800 - Red LED Lit Master Gauges, Thuemling, 6", Liquid Filled, psi, -30-0-400 Mud Flaps, Commercial Chassis Extend-A-Gun RC3, Electric, TFT, 12", XGA38VL-RL Additional Activation, Back-Up Lights Wired to Rear Work Light Switch / In-Cab Switch Bell, South Park, Chrome, Electric Striker Load Sensing System, Loadminder Display (Platform) Upper Zone A, Lightbar, Whelen, 54", Liberty LED Water Tank Overflow, Pro-Poly, 6", Pumpers w/o EHL Chevron Layout, Rear Body Surface, T1 Lap Door, Tread Plate Storage Doors Chevron Layout, Rear Body Surface, Painted Storage Doors Ladder, (1), Alco-Lite, 10' Folding Attic, with Brackets, FL-10 Seat Belt Indicator Tire Pressure Indicator, Visual, 120 PSI Handrail Material, Knurled Stainless Steel Corrosion Protection, Electrolysis Corrosion Kontrol (ECK) Platform Parapet Ground Ladder Attachment, Single Monitor Platforms Governor, Total Pressure Governor (TPG), Class 1 Pressure Gauge, 3-1/2", Thuemling, Liquid Filled - psi 0-400 Chevron Layout, Rear Body Surface, EXCLUDE Tread Plate Storage Doors Auxiliary Step, Below Rear Deck, Grip-Strut Backboard/Pike Pole Storage in Center of Hose Bed with Door Storage Compartment, Long Handle Tools, Officer's Side Rear of Body, Tread Plate Door Rear Deck, Bolt-On, Recessed Back, Tread Plate, Hinged Handrail, Pump Module, Above Pump Panel, Vertical, Driver's Side, Knurled Aluminum Handrail, Pump Module, Above Pump Panel, Vertical, Officer's Side, Knurled Aluminum Handrails, Body (Rear), Hose Bed Cover, Horizontal, Knurled Aluminum Rewind Switches, Booster Reel, (1) On Each Pump Panel Partition, Vertical, Permanent, Standard Height Compartment Refill System, Waterous, FoamFill, Single System Foam Tank, UPF, U.S. Gallon, 25 Gated Wye, Akron, 2581 Barrel Strainer, Kochek 4" Front Bumper Extension, Chassis Supplied, OEM Supplied and Installed Tread Plate Gravel Shield Clearance Lights, LED, Grote, Red, Pumper Spotlight, In Cab, Collins, Handheld, CD-CL-HID-1 Map Light, Havis Shield, 12", Side-Mounted, LED, C-MAP-T-LED Map Light, Havis Shield, 12", Side-Mounted, C-MAP-S Map Light, Havis Shield, 12", Top-Mounted, C-MAP-T Map Light, Havis Shield, 18", Side-Mounted, C-MAP-SL Map Light, Havis Shield, 18", Top-Mounted, C-MAP-TL Parking Lights, Rear Fender Wells, LED, Innovative Lighting Insight Ultimate, Fire Research - 2-1/2" Valve Size Insight Ultimate, Fire Research - 2" Valve Size Insight Ultimate, Fire Research - 3" Valve Size Insight Ultimate, Fire Research, Backlit - 4" Valve Size Insight Ultimate, Fire Research, Backlit - 2-1/2" Valve Size Insight Ultimate, Fire Research, Backlit - 2" Valve Size Insight Ultimate, Fire Research, Backlit - 3" Valve Size Platform Design/Construction/Deck Surface, BT Rear Mount Platform, Single Monitor Platform Design/Construction/Deck Surface, BT Mid Mount Platform, Single Monitor Platform Control Console, Permanent Location, (1) Joystick Control Platform Control Console, Remote Location, (1) Joystick Control Stainless Steel Screws Governor, Total Pressure Governor Plus (TPG+), Class 1 Discharge, Front Bumper Driver-Side, 1-1/2", In Hosewell, NST Primer, Trident, AirPrime (3-Barrel), Air-Operated Valve Nozzle, Electric, Akron SaberMaster 1250 GPM, 1577 (2-1/2" NH) Nozzle, Manual, TFT MasterStream 1500 GPM, M-R1500-NN (3-1/2" NH) Nozzle, Electric, TFT MasterStream 1500 GPM, M-ERP1500-NN (3-1/2" NH) Mounting Bracket, Akron, Portable Ground Base in Compartment Mounting Bracket, Akron, Apollo Monitor on Top of Body Deck Gun, Manual, Elkhart Stinger 2.0 8297-10, 3" NPT Inlet Deck Gun, Manual, Elkhart Stinger 2.0 8297-10, 3" Four-Bolt Flange Inlet Deck Gun, Manual, TFT Crossfire XFT-NJ, 3" NPT Inlet Deck Gun, Manual, TFT Typhoon Y5-D61A, 3" NPT Inlet Riser, Electric, Akron, 12", 3" NPT, 3406 Manifold, Waterous, Standard, Side Mounts, Non-Foam Manifold, Waterous, Standard, Side Mounts, Foam

007065 007066 007067 007068 007069 007074 007075 007076 007077 007080 007083 007086 007087 007090 007093 007094 007095 007096 007097 007098 007099 007100 007101 007102 007103 007104 007105 007106 007107 007108 007109 007110 007111 007112 007113 007114 007115 007116 006645 006646 006710 006729 006763 006766 006776 006781 006803 006812 006813 006818 006848 006899 006900 006912 006939 006940 006942 006947 006948 006949 006950 006951 006952 006953 006954 006964 006995 006997 006998 006999 007000 007001 007002 007003 007004 007005 007006 007007 007008 007009 007010 007011 007012 007013 007014 007018 007019 007020 007022 007023 007024 007037 007049 007050 007052 007054 007058 007059 007062 Manifold, Hale, Side Mounts, Non-Foam Manifold, Hale, Standard, Side Mounts, Foam Valve, 2", Akron, Manual, 8820, Stainless Ball, TSC Handle Valve, 2-1/2", Elkhart, Manual, EB25-D2F, Stainless Ball, D2 Handle Air Brake Refill Inlet, with Check Valve, Manual Eject Turn Signals, (2) in Wheel Well Area, LED, Truck-Lite, Model 21 Scene Light, (1), 12V, FRC, Telescoping Side Mount Push-Up, LED Focus Evolution 15,000 Lumen Siren Head, 100W, Code 3, 3930 Vehicle Data Recorder (VDR) Chassis Step Overlays, Partial, Tread Plate, 4 Door Chassis Step Overlays, Partial, Tread Plate, 2 Door Auxiliary Pump, Waterous 2515LE, Kubota 23hp Diesel Engine Air Brake Refill Inlet, with Check Valve, Auto Eject OEM Chassis Preparations, Freightliner OEM Chassis Preparations, International Foam Tank, Pro Poly, U.S. Gallon, 25 Master Gauges, Class 1, 4-1/2", Liquid Filled (No Bezel), psi -30-0-600 Master Gauges, Thuemling, 4-1/2", Liquid Filled, psi -30-0-400 Master Gauges, Thuemling, 4-1/2", Liquid Filled, Dual Scale -30-0-400 / -100-0-2800 Master Gauges, Thuemling, 4-1/2", Liquid Filled, Dual Scale -30-0-400 / -100-0-2800, Red LED Lit Master Gauges, Thuemling, 4-1/2", Liquid Filled, Dual Scale -30-0-400 / -100-0-2800, Blue LED Lit Master Gauges, Thuemling, 4-1/2", Liquid Filled, Dual Scale -30-0-400 / -100-0-2800, White LED Lit Master Gauges, Thuemling, 4-1/2", Liquid Filled, Dual Scale -30-0-400 / -100-0-2800, Green LED Lit Master Gauges, Thuemling, 4-1/2", Liquid Filled, psi, -30-0-400, Red LED Lit Master Gauges, Thuemling, 4-1/2", Liquid Filled, psi, -30-0-400, Blue LED Lit Master Gauges, Thuemling, 4-1/2", Liquid Filled, psi, -30-0-400, White LED Lit Master Gauges, Thuemling, 4-1/2", Liquid Filled, psi, -30-0-400, Green LED Lit Pump Panel Lighting, Top Mount Panel, Side Panels, LED ,On-Scene Night Axe Speedlays in Lift Out Trays, Ahead of Pump Panel, (2) 1-1/2", Stacked Speedlays on Roll Out Tray, Ahead of Pump Panel, (2) 1-1/2" Crosslays, Above Front Stabilizers, (2) 1-1/2" and (1) 2-1/2" Speedlays in Lift Out Trays, Ahead of Pump Panel, (2) 1-1/2" and (1) 2-1/2" Crosslays, Above Pump Panel, (1) 2-1/2" Crosslays, Above Pump Panel, (2) 1-1/2" Speedlay Module, Ahead of Pump Panel, (2) 1-1/2", With Lift Out Trays Crosslays, Behind Pump Panel, (2) 1-1/2" Crosslays, Ahead of Pump Panel, (2) 1-1/2" Speedlay Module, Ahead of Pump Panel, (2) 1-1/2" and (1) 2-1/2" Crosslays, Ahead of Walkway, (2) 1-1/2" Crosslays, Ahead of Walkway, (2) 1-1/2", Crosslay, Behind Pump Panel, (1) 2-1/2" Crosslays, Ahead of Walkway, (2) 1-1/2", Crosslay, Behind Pump Panel, (1) 1-1/2" Crosslays, Ahead of Walkway, In Grassfire Shield, (2) 1-1/2" Speedlay Module, Ahead of Pump Panel, (2) 1-1/2" Speedlay Module, Ahead of Pump Panel, (2) 1-1/2", Crosslays, Behind Pump Panel, (1) 2-1/2" Speedlay Module, Ahead of Pump Panel, (2) 1-1/2", Crosslays, Behind Pump Panel, (1) 1-1/2" Pre-Connect Hose Bed Housing Coating, Abraded Finish Pre-Connect Hose Bed Housing Coating, Painted, Primary Body Color Flooring, Dura-Dek Crosslay Flooring, Slotted Aluminum Crosslay Cover, Hinged Tread Plate, Side Mount Ladder Signs (2), On Base Section Ladder Signs (2), On Base Section, WITH Demo Overlays (55'/75') Ladder Signs (2), On Base Section, WITH Demo Overlays Valve, 2-1/2", Akron, Manual, 8925, Composite Ball, TSC Handle Valve, 3", Akron, Manual, Slow Close, 8930, Composite Ball, TSC Handle Butterfly Valve, 4", Akron, Gear, 7940, With Handwheel Valve, 3", Akron, Manual, Slow Close, 8830, Stainless Ball, TSC Handle Valve, 3", Elkhart, Manual, Slow Close, EB30-D2F, Stainless Ball, D2 Handle Butterfly Valve, 5", Elkhart, Gear, EB5B, With Handwheel Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, TSC Handle Butterfly Valve, 5", Akron, Gear, 7950, With Handwheel Tank to Pump, 3", Legend, Check Valve Valve, Discharge Check Valves Butterfly Valve, Side Steamer, 5" Air, Neles Jamesbury Butterfly Valve, Side Steamer, 6" Air, Neles Jamesbury Butterfly Valve, Side Steamer, 6" Air, Waterous Monarch Manifold, Waterous, Top Mounts, Non-Foam Manifold, Waterous, Standard, Top Mounts, Foam Manifold, Hale, Top Mounts, Non-Foam Manifold, Hale, Standard, Top Mounts, Foam Butterfly Valve, Side Steamer, 6" Manual, Hale MIV-M Preconnect, Hose Bed Officer-Side, 2-1/2", NST Inlet, Driver-Side, 3", Fully Recessed Body Striping, Aerial, Lap Doors, 4", S-Ribbon Transition with 3D Shadow Body Striping, Aerial, Lap Doors, 6", S-Ribbon Transition with 3D Shadow Body Striping, Aerial, Lap Doors, 1"-4"-1", S-Ribbon Transition with 3D Shadow Inlet, Officer-Side, 3", Partially Recessed Body Striping, Aerial, Lap Doors, 1"-6"-1", S-Ribbon Transition with 3D Shadow Body Striping, Aerial, Rollup Doors, 4", S-Ribbon Transition with 3D Shadow Inlet, Officer-Side, 3", Fully Recessed Body Striping, Aerial, Rollup Doors, 6", S-Ribbon Transition with 3D Shadow Body Striping, Aerial, Rollup Doors, 1"-4"-1", S-Ribbon Transition with 3D Shadow Body Striping, Aerial, Rollup Doors, 1"-6"-1", S-Ribbon Transition with 3D Shadow Body Striping, Aerial, Lap Doors, 4", Z Transition Body Striping, Aerial, Lap Doors, 6", Z Transition Body Striping, Aerial, Lap Doors, 1"-4"-1", Z Transition Body Striping, Aerial, Lap Doors, 1"-6"-1", Z Transition Body Striping, Aerial, Rollup Doors, 4", Z Transition Body Striping, Aerial, Rollup Doors, 6", Z Transition Body Striping, Aerial, Rollup Doors, 1"-4"-1", Z Transition Body Striping, Aerial, Rollup Doors, 1"-6"-1", Z Transition Air Horn Activation, Push Button, Driver's Side Air Horn Activation, Push Button, Officer's Side Air Horns (2), Chassis Supplied, OEM Installed Front Bumper Extension, 24", Tread Plate Gravel Shield, IHC Front Bumper Extension, 24", Tread Plate Gravel Shield, Freightliner Fog Lights, Under Front Bumper Fog Lights, Chassis Supplied, OEM Installed, Recessed Into Front Bumper Fog Lights, Chassis Supplied, OEM Installed, Under Front Bumper

007291 007292 007294 007295 007296 007297 007298 007299 007300 007301 007302 007303 007304 007305 007306 007307 007308 007309 007310 007311 007312 007313 007314 007315 007316 007317 007318 007319 007320 007321 007322 007323 007324 007325 007326 007327 007328 007329 007123 007124 007125 007126 007127 007128 007129 007130 007131 007133 007134 007135 007137 007138 007160 007188 007191 007192 007194 007206 007207 007208 007213 007214 007215 007216 007217 007218 007219 007220 007221 007222 007223 007224 007225 007226 007227 007228 007229 007230 007231 007232 007233 007234 007235 007236 007237 007238 007247 007266 007267 007274 007275 007276 007284 007285 007286 007287 007288 007289 007290 Speaker, (1), Chassis Supplied, OEM Installed Siren Activation, (1) Foot Switch, Driver's Side Siren Activation, (1) Foot Switch, Officer's Side Siren Activation, (1) Push Button, Driver's Side Siren Activation, (1) Push Button, Officer's Side Additional Brake, Push Button Siren, Screaming Eagle, Eagle Sirens, Partially-Recessed Siren, Q2B, Chassis Supplied, OEM Installed, Pedestal Mount Siren, Q2B, Chassis Supplied, OEM Installed, Recess Mount Siren Head, 100W/200W, Whelen, 295HFS2, Remote Siren Head Siren Head, 100W/200W, Powercall, 6-Adam Siren Head, Chassis Supplied, OEM Installed Platform Striping, Reflective, Angle Up Platform Striping, Reflective, Angle Down Access Panel, Pump, Front Pump Module, Bolt-On, Painted Aluminum, Bolt-On Handrail, Body (Rear), Ladder Storage Area in Hose Bed, Top, Knurled Aluminum Access Panel, Pump, Driver's Side, Side-Hinged, Painted Aluminum, Compression Latches Access Panel, Pump, Officer's Side, Side-Hinged, Painted Aluminum, Compression Latches Skull-Saver, FRC, (1) Generator Location, Above Front of Body, Harrison Generator Location, Above Front of Body, Onan Generator Location, Above Front of Body, Smart Power Breathing Air System, Single Bottle, 4500 PSI (75') Breathing Air System, Single Bottle, 6000 PSI (75') Breathing Air System, Single Bottle, 4500 PSI (105') Breathing Air System, Single Bottle, 6000 PSI (105') Breathing Air System, Single Bottle, 4500 PSI (100' SHD) Breathing Air System, Single Bottle, 6000 PSI (100' SHD) Breathing Air System, Single Bottle, 4500 PSI (125') Breathing Air System, Single Bottle, 6000 PSI (125') Breathing Air System, Single Bottle, 4500 PSI (100' RMP) Breathing Air System, Single Bottle, 6000 PSI (100' RMP) Breathing Air System, Dual Bottles, 4500 PSI (100' RMP) Breathing Air System, Dual Bottles, 6000 PSI (100' RMP) Breathing Air System, Single Bottle, 4500 PSI (85' RMP) Breathing Air System, Single Bottle, 6000 PSI (85' RMP) Breathing Air System, Dual Bottles, 4500 PSI (85' RMP) Breathing Air System, Dual Bottles, 6000 PSI (85' RMP) Breathing Air System, Single Bottle, 4500 PSI (85' MMP) Breathing Air System, Single Bottle, 6000 PSI (85' MMP) Breathing Air System, Dual Bottles, 4500 PSI (85' MMP) Breathing Air System, Dual Bottles, 6000 PSI (85' MMP) Breathing Air System, Single Bottle, 4500 PSI (100' MMA) Breathing Air System, Single Bottle, 6000 PSI (100' MMA) Breathing Air System, Single Bottle, 4500 PSI (100' MMP) Breathing Air System, Single Bottle, 6000 PSI (100' MMP) Breathing Air System, Dual Bottles, 4500 PSI (100' MMP) Breathing Air System, Dual Bottles, 6000 PSI (100' MMP) Breathing Air Level and Warning System, Class 1 Dual AirMinder, Turntable and Platform Pinstriping, Pumper, Gold Leaf, Engine-Turned 23.5kt

Pinstriping, Aerial, Gold Leaf, Engine-Turned 23.5kt

Two-Tone Paint Break, Reflective Striping Two-Tone Paint Break, Engine-Turned 22kt Gold Leaf Striping Two-Tone Paint Break, Engine-Turned 23.5kt Gold Leaf Striping Decal, Reflective, 9" Wavy American Flag with Eagle Head on Flag Decal, Reflective, 11" Eagle Head with American Flag on Head Decal, Reflective, 10" Landing Eagle with American Flag on Background Decal, Reflective, 18" Wavy American Flag on Pole with Landing Eagle Decal, Aerial Ladder Sign, Canadian Flag Background Decal, Aerial Ladder Sign, American Flag Background Body Striping, Pumper, Lap Doors, 4", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 6", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 1"-4"-1", Straight Around Perimeter, 1/4" Accent Stripe Anodes, OEM, Alloy, 2 Discharge, 2 Intake Anodes, OEM, Alloy, 1 Discharge, 1 Intake Anodes, OEM, Alloy, 1 Intake Valve, 2", Akron, Manual, 8920, Composite Ball, TSC Handle Egress, Integral, Short (55') Nozzle, Manual, Akron SaberMaster 2000 GPM, 5170, 3-1/2" NH Nozzle, Manual, Elkhart X-Stream 2000 GPM, SM-2000, 3-1/2" NH Nozzle, Electric, Elkhart X-Stream 2000 GPM, SM-2000E, 3-1/2" NH Body Striping, Pumper, Lap Doors, 1"-6"-1", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Pumper, 4", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 6", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 1"-4"-1", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 1"-6"-1", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 4", High Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 6", High Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 1"-4"-1", High Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 1"-6"-1", High Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 4", High Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 6", High Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 1"-4"-1", High Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 1"-6"-1", High Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 4", Low Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 6", Low Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 1"-4"-1", Low Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 1"-6"-1", Low Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 4", Low Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 6", Low Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 1"-4"-1", Low Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 1"-6"-1", Low Angle Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 4", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 6", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 1"-4"-1", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 1"-6"-1", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Pumper, 4", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Pumper, 6", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Pumper, 1"-4"-1", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe

007394 007395 007397 007399 007400 007407 007408 007409 007410 007411 007412 007413 007414 007417 007421 007423 007424 007428 007430 007435 007440 007441 007454 007456 007458 007459 007460 007462 007473 007474 007475 007486 007487 007539 007543 007544 007545 007546 007330 007331 007332 007333 007334 007335 007336 007337 007338 007339 007340 007341 007342 007343 007344 007345 007346 007347 007348 007349 007350 007351 007352 007353 007354 007355 007356 007357 007358 007359 007360 007361 007362 007363 007364 007365 007366 007367 007368 007369 007370 007371 007372 007373 007374 007375 007376 007377 007378 007379 007380 007381 007382 007383 007384 007385 007386 007387 007388 007390 007391 Body Striping, Pumper, 1"-6"-1", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 4", Z Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 6", Z Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 1"-4"-1", Z Transition, 1/4" Accent Stripe Body Striping, Pumper, Lap Doors, 1"-6"-1", Z Transition, 1/4" Accent Stripe Body Striping, Pumper, 4", Z Transition, 1/4" Accent Stripe Body Striping, Pumper, 6", Z Transition, 1/4" Accent Stripe Body Striping, Pumper, Rollup Doors, 1"-4"-1", Z Transition, 1/4" Accent Stripe Body Striping, Pumper, 1"-6"-1", Z Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 4", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 6", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-4"-1", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-6"-1", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 4", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 6", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 1"-4"-1", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 1"-6"-1", Straight Around Perimeter, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 4", High Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 6", High Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-4"-1", High Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-6"-1", High Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 4", High Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 6", High Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 1"-4"-1", High Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 1"-6"-1", High Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 4", Low Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 6", Low Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-4"-1", Low Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-6"-1", Low Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 4", Low Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 6", Low Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 1"-4"-1", Low Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 1"-6"-1", Low Angle Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 4", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 6", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-4"-1", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-6"-1", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Aerial, 4", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Aerial, 6", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Aerial, 1"-4"-1", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Aerial, 1"-6"-1", S-Ribbon Transition with 3D Shadow, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 4", Z Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 6", Z Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-4"-1", Z Transition, 1/4" Accent Stripe Body Striping, Aerial, Lap Doors, 1"-6"-1", Z Transition, 1/4" Accent Stripe Body Striping, Aerial, 4", Z Transition, 1/4" Accent Stripe Body Striping, Aerial, 6", Z Transition, 1/4" Accent Stripe Body Striping, Aerial, 1"-4"-1", Z Transition, 1/4" Accent Stripe Body Striping, Aerial, Rollup Doors, 1"-6"-1", Z Transition, 1/4" Accent Stripe Turntable Control Console, Traditional, (3) Levers, On-Scene LED Light Under Lid (Ladders) Chevron Layout, Rear Body Surface, Torque Box Lap Door Chevron Layout, Rear Body Surface, Torque Box Rollup Door Chevron Layout, Rear Body Surface, EXCLUDE Torque Box Door Chevron Layout, Rear Body Surface, Torque Box Lap Door, Ladder Storage Doors Chevron Layout, Rear Body Surface, Torque Box Rollup Door, Ladder Storage Doors Chevron Layout, Rear Body Surface, Torque Box Lap Door, EXCLUDE Ladder Storage Doors Chevron Layout, Rear Body Surface, Torque Box Rollup Door, EXCLUDE Ladder Storage Doors Chevron Layout, Rear Body Surface, Ladder Storage Doors, EXCLUDE Torque Box Door Chevron Layout, Rear Body Surface, EXCLUDE Torque Box Door, Ladder Storage Doors Turntable Control Console, AL-11, On-Scene Light Under Lid (55'/75'/105'/125') Anode, Additional, (1) OEM Supplied on Discharge Side of Pump Foam Bypass, Deluge Turntable Handrails, Knurled SS, Officer's Side Cut-Off Turntable, (2) Openings (75') Clearance Lights, With Rubber Extension Arms, LED, Grote and Truck-Lite, Red Turntable Control Console, AL-11, On-Scene LED Light Under Lid (85' RMP/100' RMP) Turntable Control Console, AL-11, On-Scene LED Light Under Lid (85' MMP/100' MMP) Load Sensing System, Programmed into AL-11 Breathing Air Level and Warning System, Programmed into AL-11 Generator Load Center, 12-Circuit, Non-GFI Breaker Box Generator Load Center, 16-Circuit, Non-GFI Breaker Box Generator Load Center, 20-Circuit, Non-GFI Breaker Box Generator Load Center, 12-Circuit, GFI Breaker Box Generator Load Center, 16-Circuit, GFI Breaker Box Generator Load Center, 20-Circuit, GFI Breaker Box Aerial Monitor, Manual, Akron, StreamMaster 3570 Generator Start, Hydraulic Gen., On Pump Panel Upper Zone A, Lightbar, Federal Signal, 72", Jet Solaris LED, JLX7201-NFPA Transfer Valve, Hale, Air-Operated Butterfly Valve, Front Steamer, 5" Air, Neles Jamesbury Butterfly Valve, Front Steamer, 6" Air, Waterous Monarch Chevron Layout, Rear Body Surface, EXCLUDE T1, Tread Plate Storage Doors Crosslays, Above Pump Panel, (2) 1-1/2" and (1) 2-1/2" Crosslays, Above Front Stabilizers, (1) 2-1/2" Load Chart (85' MMP - 1000/1000) Overlay, Tread Plate, Rear Center Area Overlay, Tread Plate, Behind Rear Steps, Driver's Side Overlay, Behind Officer's Side Rear Steps, Tread Plate Compartment Finish, Amerlock, White Foam Bypass, Deluge, With Diffuser (CAFS Only) Aerial 4" Waterway Foam Bypass Aerial 5" Waterway Foam Bypass Cap, 6" NST, Vented Chrome, Trident, Smeal Logo Ladder, (1), Alco-Lite, 20' Roof, PRL-20 Extend Chassis Air Tank Drains, Outside of Body Generator Start, Hydraulic Gen., In Cab Scene Light, (1), 120V, FRC, Surface Mount, LED Spectra 15,000 Lumen Scene Light, (1), 12V, FRC, Surface Mount, LED Spectra 15,000 Lumen Scene Light, (1), 120V, FRC, Telescoping Top Mount Pull-Up, LED Spectra 20,000 Lumen Scene Light, (1), 12V, FRC, Telescoping Top Mount Pull-Up, LED Spectra 20,000 Lumen

007738 007739 007740 007741 007742 007743 007744 007745 007746 007747 007748 007749 007750 007751 007752 007753 007754 007767 007768 007769 007770 007771 007772 007773 007774 007775 007776 007777 007791 007792 007794 007795 007796 007797 007798 007799 007806 007808 007547 007548 007549 007550 007551 007557 007558 007561 007564 007571 007572 007573 007574 007582 007596 007597 007598 007599 007600 007603 007606 007609 007610 007616 007626 007632 007633 007637 007638 007649 007651 007660 007685 007686 007687 007710 007711 007712 007713 007714 007715 007716 007717 007718 007719 007720 007721 007722 007723 007724 007725 007728 007729 007730 007731 007732 007733 007734 007735 007736 007737 Scene Light, (1), 120V, FRC, Telescoping Thru The Roof Push-Up, LED Spectra 20,000 Lumen Scene Light, (1), 12V, FRC, Telescoping Thru The Roof Push-Up, LED Spectra 20,000 Lumen Scene Light, (1), 12V, FRC, Telescoping Side Mount Push-Up, LED Spectra 20,000 Lumen Scene Light, (1), 120V, FRC, Telescoping Side Mount Pull-Up LED Spectra 20,000 Lumen Scene Light, (1), 12V, FRC, Telescoping Side Mount Pull-Up, LED Spectra 20,000 Lumen Scene Light, (1), 120V, FRC, Brow Mount, LED Spectra 20,000 Lumen Scene Light, (1), 12V, FRC, Brow Mount, LED Spectra 15,000 Lumen Crosslays, Behind Pump Panel, (2) 1-1/2" and (1) 2-1/2" Sill Protectors, Stainless Steel Ladder, (1), Alco-Lite, 10' "Fresno" Attic Extension, AEL-10 Ladder, (1), Alco-Lite, 14' "Fresno" Attic Extension, AEL-14 Platform Control Console, AL-11 EMS Compartments, Two (2), (1) Each Behind the Driver's Seat and Officer's Seat Lighting Location, On Rear Face of Custom Chassis, Officer's Side Discharge, Aerial Waterway, 4" (105'/125') Discharge, Aerial Waterway, 5" (100' RMP) Discharge, Aerial Waterway, 5" (85' RMP) Ladder Storage, Inside Body, Side of Water Tank, Driver's Side, Tread Plate Door Ladder Storage, Inside Body, Side of Water Tank, Driver's Side, Painted Aluminum Door Ladder Storage, Above Low Sides, Driver's Side, OEM Brackets Map Console, 3-Slot, Behind Floor Console Stabilizer Cover Warning Lights (4), Whelen, 600 Series Super LED, Red, Activated with Aerial Master Stabilizer Cover Warning Lights (2), Whelen, 600 Series Super LED, Red, Activated with Aerial Master Receptacle, 120V, 5-20R Straight Blade, Duplex, Wired to Shoreline Body, 100" Wide, Custom Pumper, Single-Axle, 409 Stainless Steel Ventilation Panel, SG-09, Driver's Side Pump Module, Bolt-On, Painted Aluminum Access/Ventilation Panel, SG-09, Officer's Side Pump Module, Side-Hinged, Tread Plate, Compression Latches Non-Painted 304 Stainless Brushed Finish Compartment Finish, Stainless Camera System, Back-Up, ASA Audiovox, Single Secondary Sump Location, Rear of Water Tank Recirculation System, Powered by SG-09 Adapter, 2-1/2" FNST x 2-1/2" MCSA - CSA Cap, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MBCT - BCT Cap, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MAMA - AMA Cap, Chrome, South Park Torque Box, Hot Dip Galvanized (55') Torque Box, Painted Black, PPG# MTK-9000 (55') Torque Box, Hot Dip Galvanized (75' Single Axle) Torque Box, Painted Black, PPG# MTK-9000 (75' Single Axle) Torque Box, Hot Dip Galvanized (75' Tandem Axle) Torque Box, Painted Black, PPG# MTK-9000 (75' Tandem Axle) Torque Box, Hot Dip Galvanized (100' MMA) Torque Box, Painted Black, PPG# MTK-9000 (100' MMA) Torque Box, Hot Dip Galvanized (85' RMP/105') Torque Box, Painted Black, PPG# MTK-9000 (85' RMP/105') Torque Box, Hot Dip Galvanized (100' MMP) Torque Box, Painted Black, PPG# MTK-9000 (100' MMP) Torque Box, Hot Dip Galvanized (UT 100') Torque Box, Painted Black, PPG# MTK-9000 (UT 100') Torque Box, Hot Dip Galvanized (100' RMP/125') Torque Box, Painted Black, PPG# MTK-9000 (100' RMP/125') Fire Truck Leveling (FTL) Assist, Leveling System and Display, Non-Multiplex Cab Fire Truck Leveling (FTL) Assist, Leveling System and Display, Multiplex Cab Waterway Inlet/Outlet, Rear, 4" Inlet and 4" Plumbing, Waterway Valve Controlled at Pump Panel (55') Waterway Inlet/Outlet, Rear, 4" Inlet and 4" Plumbing, Waterway Valve Controlled at Pump Panel (75') Waterway Inlet/Outlet, Rear, 4" Inlet and 4" Plumbing, Waterway Valve Controlled at Pump Panel (105') Waterway Inlet/Outlet, Rear, 5" Inlet and 5" Plumbing, Waterway Valve Controlled at Pump Panel (85' RMP/100' RMP/125') Valve, 4", Akron, Electric, 8840, Stainless Ball, 9323 Navigator Pro Controller (Valve Only) Valve, 4", Akron, Electric, 8940, Composite Ball, 9323 Navigator Pro Controller (Valve Only) Valve, 4", Elkhart, Electric, EB40-E1F, Stainless Ball, UBEC1 Controller (Valve Only) Butterfly Valves (2), 4", Akron, Gear, 7940, With Handwheel Valves (2), 4", Akron, Electric, 8840, Stainless Ball, 9323 Navigator Pro Controller (Valve Only) Valves (2), 4", Akron, Electric, 8940, Composite Ball, 9323 Navigator Pro Controller (Valve Only) Butterfly Valves (2), 5", Akron, Gear, 7950, With Handwheel Butterfly Valves (2), 4", Elkhart, Gear, EB4B, With Handwheel Valves (2), 4", Elkhart, Electric, EB40-E1F, Stainless Ball, UBEC1 Controller (Valve Only) Butterfly Valves (2), 5", Elkhart, Gear, EB5B, With Handwheel Chrome Bushing, 4" NPT x 4" NST - NST Cap, Chrome, South Park Chrome Bushing, 4" NPT x 5" NST - NST Cap, Chrome, South Park Chrome Bushing, 5" NPT x 5" NST - NST Cap, Chrome, South Park Chrome Bushing, 5" NPT x 6" NST - NST Cap, Chrome, South Park Chrome Bushing, 4" NPT x 4" NST - Elbow (30 Deg.) 4" FNST x 4" MNST - NST Cap, Chrome, South Park Chrome Bushing, 4" NPT x 4" NST - NST Cap, Chrome, Trident Chrome Bushing, 4" NPT x 5" NST - NST Cap, Chrome, Trident Chrome Bushing, 5" NPT x 5" NST - NST Cap, Chrome, Trident Chrome Bushing, 5" NPT x 6" NST - NST Cap, Chrome, Trident Chrome Bushing, 5" NPT x 6" NST - NST Cap, Chrome, Trident, Smeal Logo Chrome Bushing, 4" NPT x 4" NST - Elbow (30 Deg.) 4" FNST x 4" MNST - NST Cap, Chrome, Trident Chrome Bushings (2), 4" NPT x 4" NST - NST Caps (2), Chrome, South Park Chrome Bushings (2), 4" NPT x 5" NST - NST Caps (2), Chrome, South Park Chrome Bushings (2), 5" NPT x 5" NST - NST Caps (2), Chrome, South Park Chrome Bushings (2), 5" NPT x 6" NST - NST Caps (2), Chrome, South Park Chrome Bushings (2), 4" NPT x 4" NST - Elbows (2) (30 Deg.) 4" FNST x 4" MNST - NST Caps (2), Chrome, South Park Chrome Bushings (2), 4" NPT x 4" NST - NST Caps (2), Chrome, Trident Chrome Bushings (2), 4" NPT x 5" NST - NST Caps (2), Chrome, Trident Chrome Bushings (2), 5" NPT x 5" NST - NST Caps (2), Chrome, Trident Chrome Bushings (2), 5" NPT x 6" NST - NST Caps (2), Chrome, Trident Chrome Bushings (2), 5" NPT x 6" NST - NST Caps (2), Chrome, Trident, Smeal Logo Chrome Bushings (2), 4" NPT x 4" NST - Elbows (2) (30 Deg.) 4" FNST x 4" MNST - NST Caps (2), Chrome, Trident Torque Box, Hot Dip Galvanized (85' MMP) Torque Box, Painted Black, PPG# MTK-9000 (85' MMP) Ladder, (1), Alco-Lite, 40' Three-Section Extension with Stay Poles, PEL3-40P Ladder, (1), Duo-Safety, 40' Three-Section Extension with Stay Poles, 1525-A Ladder, (1), Duo-Safety, 40' Three-Section Extension (No Poles), 1525-A Axe Mounting Bracket (1), Fly Section, WITH Flat Head Axe Axe Mounting Bracket (1), Fly Section, WITH Pick Head Axe Axe Mounting Bracket (1), In Platform, WITH Flat Head Axe Chassis Step and Fuel Tank Overlays, Full, Tread Plate, Commercial Tool Board, (1), Slide Out Aluminum, Full Height, Full Depth, Abraded, Locking Roller Assembly

007903 007904 007906 007908 007916 007917 007918 007919 007920 007921 007922 007923 007924 007925 007926 007927 007928 007929 007966 007967 008022 008024 008025 008026 008031 008037 008045 008046 008047 008048 008055 008084 008098 008099 008100 008101 008102 008103 007809 007810 007811 007812 007813 007814 007815 007816 007817 007825 007844 007845 007846 007847 007848 007849 007850 007851 007852 007853 007854 007855 007856 007857 007858 007859 007860 007861 007862 007863 007864 007865 007866 007867 007868 007869 007870 007871 007872 007873 007874 007875 007876 007878 007885 007887 007888 007889 007890 007891 007892 007893 007894 007895 007896 007897 007898 007899 007900 007901 007902 Tool Board, (1), Slide Out Aluminum, Full Height, Full Depth, Abraded Pegboard, Locking Roller Assembly Tool Board, (1), Slide Out Aluminum, Full Height, Full Depth, Line-X, Locking Roller Assembly Tool Board, (1), Slide Out Aluminum, Full Height, Full Depth, Double-Faced PAC TRAC, Locking Roller Assembly Tool Board, (1), Slide Out Aluminum, Full Height, Split Depth, Abraded, Locking Roller Assembly Tool Board, (1), Slide Out Aluminum, Full Height, Split Depth, Abraded Pegboard, Locking Roller Assembly Tool Board, (1), Slide Out Aluminum, Full Height, Split Depth, Line-X, Locking Roller Assembly Tool Board, (1), Slide Out Aluminum, Full Height, Split Depth, Double-Faced PAC TRAC, Locking Roller Assembly Crosslay Top Covers, Hinged Tread Plate Outside Covers, Center Vinyl, Button Snaps, Black (Mid Mounts) Provisions for Nederman Anchor Plate, Customer/Dealer Supplied and Installed Aerial Egress Striping, Reflective White Zico Quic-Ladder, 12" Wide, 4-Step with 2-Step Drop Down, Driver's Side-Rear Zico Quic-Ladder, 12" Wide, 4-Step with 2-Step Drop Down, Officer's Side-Rear Zico Quic-Ladder, 15" Wide, 4-Step with 2-Step Drop Down, Driver's Side-Rear Zico Quic-Ladder, 15" Wide, 4-Step with 2-Step Drop Down, Officer's Side-Rear Zico Quic-Ladder, 18" Wide, 4-Step with 2-Step Drop Down, Driver's Side-Rear Zico Quic-Ladder, 18" Wide, 4-Step with 2-Step Drop Down, Officer's Side-Rear Zico Quic-Ladder, 18" Wide, 5-Step with 2-Step Drop Down, Driver's Side-Rear Zico Quic-Ladder, 18" Wide, 5-Step with 2-Step Drop Down, Officer's Side-Rear Zico Quic-Ladder, 18" Wide, 6-Step with 2-Step Drop Down, Driver's Side-Rear Zico Quic-Ladder, 18" Wide, 6-Step with 2-Step Drop Down, Officer's Side-Rear Rear Steps and Lighting, Cast Products, Bolt-On Steps, Two (2), 2 Driver's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Two (2), 2 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Three (3), 3 Driver's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Three (3), 3 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Four (4), 4 Driver's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Four (4), 3 Driver's and 1 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Four (4), 2 Driver's Side and 2 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Four (4), 1 Driver's Side and 3 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Four (4), 4 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Five (5), 5 Driver's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Five (5), 4 Driver's Side and 1 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Six (6), 4 Driver's Side and 2 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Six (6), 3 Driver's Side and 3 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Six (6), 2 Driver's Side and 4 Officer's Side Rear Steps and Lighting, Cast Products, Bolt-On Steps, Eight (8), 4 Driver's Side and 4 Officer's Side Rear Steps and Lighting, Cast Products, Folding Steps, Three (3), 3 Driver's Side Rear Steps and Lighting, Cast Products, Folding Steps, Four (4), 4 Driver's Side Rear Steps and Lighting, Cast Products, Folding Steps, Four (4), 2 Driver's Side and 2 Officer's Side Rear Steps and Lighting, Cast Products, Folding Steps, Six (6), 3 Driver's Side and 3 Officer's Side Rear Steps and Lighting, Cast Products, Corner Steps, Four (4), 2 Driver's Side and 2 Officer's Side Rear Steps and Lighting, Cast Products, Corner Steps, Six (6), 3 Driver's Side and 3 Officer's Side Rear Steps and Lighting, Cast Products, Folding and Corner Steps, Four (4), 1 Each Driver's Side and 1 Each Officer's Side Flashlight, (1), Streamlight, Fire Vulcan LED, Orange, 44451, Vehicle Mount System Stacked Tips (Quad) and Stream Shaper, TFT, MST-4NN, XF-SS10 (3-1/2" NH) Nozzle, Manual, Akron Akromatic 1250 GPM, 5160, 3-1/2" NH Nozzle, Electric, Akron Akromatic 1250 GPM, 5177, 3-1/2" NH Nozzle, Manual, Elkhart X-Stream 1250 GPM, SM-1250 (2-1/2" NH) Nozzle, Manual, Elkhart X-Stream 1000 GPM, SM-1000 (2-1/2" NH) Nozzle, Electric, Elkhart X-Stream 1250 GPM, SM-1250E (2-1/2" NH) Nozzle, Electric, Elkhart X-Stream 1000 GPM, SM-1000E (2-1/2" NH) Chevron Color, Red / Fluorescent Yellow Chevron Color, Red / Yellow Front Step and Lighting, Cast Products, Folding Step (1), Driver's Side Front Steps and Lighting, Cast Products, Folding Steps (2), Driver's Side Front Steps and Lighting, Cast Products, Folding Steps (3), Driver's Side Front Steps and Lighting, Cast Products, Folding Steps (4), Driver's Side Front Steps and Lighting, Cast Products, Folding Steps (5), Driver's Side Front Step and Lighting, Cast Products, Folding Step (1), Officer's Side Front Steps and Lighting, Cast Products, Folding Steps (2), Officer's Side Front Steps and Lighting, Cast Products, Folding Steps (3), Officer's Side Front Steps and Lighting, Cast Products, Folding Steps (4), Officer's Side Front Steps and Lighting, Cast Products, Folding Steps (5), Officer's Side Ladder, (1), Alco-Lite, 12' Roof, PRL-12 Turntable Access Steps, Driver's Side, Grote LED Light, Knurled Aluminum Handrails, Rear Mounts Turntable Access Steps, Driver's Side, Grote LED Light, Knurled Stainless Steel Handrails, Rear Mounts Ladder Creeper Controls at Tip, Switched at Turntable Console (55') Ladder Creeper Controls at Tip, Switched Through AL-11 (55') Ladder Creeper Controls at Tip, Switched at Turntable Console (75') Ladder Creeper Controls at Tip, Switched Through AL-11 (75') Ladder Creeper Controls at Tip, Switched at Turntable Console (105'/125') Ladder Creeper Controls at Tip, Switched Through AL-11 (105'/125') Ladder Creeper Controls at Tip, Switched at Turntable Console (100' MMA/UT 100'/100' SHD/100' Tiller) Ladder Creeper Controls at Tip, Switched Through AL-11 (100' MMA/UT 100'/100' SHD/100' Tiller) Positional Waterway, Switched at Turntable Console (75'/105') Positional Waterway, Switched Through AL-11 (75'/105') Positional Waterway, Switched at Turntable Console (55') Positional Waterway, Switched Through AL-11 (55') Positional Waterway, Switched at Turntable Console (125') Positional Waterway, Switched Through AL-11 (125') Platform Telescoping Lights (2), 120V, FRC, Halogen Focus 500W, Switch on Lighthead Platform Telescoping Lights (2), 120V, FRC, LED Spectra 20,000 Lumen, Switch on Lighthead Communication System, 2-Way, Turntable-Tip, FRC Always Clear Talking (ACT) Retraction Override Safety System, Switched at Turntable Console Retraction Override Safety System, Switched Through AL-11 Communication System, 3-Way, Pump Panel-Turntable-Tip, FRC Always Clear Talking (ACT) Nozzle, Manual, TFT MasterStream 1250 GPM, M-R1250S-NN (3-1/2" NH) Turntable Work Lights, (4) Whelen LED Plug, NST, 2-1/2", Trident Plug, CSA, 2-1/2", Trident Plug, BCT, 2-1/2", Trident Plug, AMA, 2-1/2", Trident Cap, NST, 3", Chrome, Trident Axe Mounting Bracket (1), In Platform, WITH Pick Head Axe Hydraulic Pump with "Thru-Drive", Generator Operation in Drive (55') Hydraulic Pump with "Thru-Drive", Generator Operation in Drive (75'/105') Hydraulic Pump with "Thru-Drive", Generator Operation in Drive (100' MMP) Hydraulic Pump with "Thru-Drive", Generator Operation in Drive (85' MMP/85' RMP/100' RMP/125') Stacked Tips (Quad), Akron, 3499 Stacked Tips (Quad) and Stream Shaper, Akron, 3499, 3485

008265 008266 008267 008268 008269 008270 008271 008272 008273 008275 008277 008282 008283 008285 008286 008288 008289 008290 008291 008292 008293 008294 008295 008296 008297 008304 008305 008306 008307 008309 008310 008311 008312 008313 008314 008315 008316 008317 008105 008106 008108 008110 008111 008113 008114 008119 008120 008171 008172 008173 008174 008175 008176 008177 008178 008179 008180 008181 008182 008183 008184 008185 008186 008187 008188 008197 008198 008199 008200 008201 008202 008203 008204 008205 008206 008207 008208 008209 008210 008211 008212 008213 008214 008215 008216 008217 008218 008219 008221 008227 008228 008231 008233 008242 008249 008258 008262 008263 008264 Foam System, Waterous, Advantus 3, Dual System, Electronic Selector, Class A and B Foam, Flush System Foam System, Waterous, Advantus 6, Dual System, Electronic Selector, Class A and B Foam, Flush System Instrument Panel and Throttle, at Pump Panel, Waterous PB-18-2515 Instrument Panel and Throttle, at Pump Panel, Waterous 2515LE Instrument Panel and Throttle, at Pump Panel, Waterous E511 Priming System, Waterous VAP Primer in Cab, Waterous VAP Overboard Foam Fill Kit, Waterous Refill System, Waterous, FoamFill, Dual System Water Tank Level Display, Chassis Supplied 4-Light, Cab Sides, FRC Driver Foam Tank, Pro Poly, Imperial Gallon, 8 Foam Tank, Pro Poly, Imperial Gallon, 15 Foam Tank, Pro Poly, Imperial Gallon, 25 Foam Tank, Pro Poly, Imperial Gallon, 30 Foam Tank, Pro Poly, Imperial Gallon, 40 Foam Tank, Pro Poly, Imperial Gallon, 80 Foam Tank, UPF, Imperial Gallon, 8 Foam Tank, UPF, Imperial Gallon, 15 Foam Tank, UPF, Imperial Gallon, 25 Foam Tank, UPF, Imperial Gallon, 40 Foam Tank, UPF, Imperial Gallon, 20 Foam Tank, UPF, Imperial Gallon, 80 Water Tank Mounting, UPF, 55' Aerial Water Tank Mounting, UPF, Non 55'/75' Rear Mount Aerials Water Tank Mounting, UPF, Mid Mounts Water Tank Overflow, UPF, 4", Pumpers w/o EHL PSTANK Gauge, Chassis Supplied, OEM Wiring to Existing Sending Unit Plug, NST, 3", Trident Ladder, (1), Duo-Safety, 10' "Fresno" Attic Extension, 701 Ladder, (1), Duo-Safety, 14' Special Width Roof, 775-A Ladder, (1), Duo-Safety, 16' Special Width Roof, 875-A Ladder, (1), Duo-Safety, 28' Three-Section Extension, 1225-A Ladder, (1), Alco-Lite, 40' Three-Section Extension (No Poles), PEL3-40 Ladder, (1), Wing Enterprises, 17' Little Giant Ladder Type 1A, 10102LG Pike Pole, (1), Duo-Safety, 6' Fiberglass, Standard Hook, D-Handle, FP6D Pike Pole, (1), Duo-Safety, 14' Fiberglass, Standard Hook, FP14 Pike Pole, (1), Nupla, 6' Fiberglass, Standard Hook, Super-Duty, D-Handle, SPDH-6 Pike Pole, (1), Fire Hooks Unlimited, 4' Fiberglass, National Hook, Ash Core, D-Handle, NHF-4 w/D Pike Pole, (1), Fire Hooks Unlimited, 6' Fiberglass, All Purpose Hook, APH-6 Pike Pole, (1), Fire Hooks Unlimited, 6' Fiberglass, All Purpose Steel Hook, APS-6 Pike Pole, (1), Fire Hooks Unlimited, 6' Fiberglass, National Hook, Ash Core, NHF-6 Pike Pole, (1), Fire Hooks Unlimited, 6' Fiberglass, New Yorker Hook, Ash Core Super, NYFG-6 Pike Pole, (1), Fire Hooks Unlimited, 6' Fiberglass, Arson Trash Hook, D-Handle, TRH-6 w/D Pike Pole, (1), Fire Hooks Unlimited, 8' Fiberglass, National Hook, Ash Core, NHF-8 Pike Pole, (1), Fire Hooks Unlimited, 8' Fiberglass, New Yorker Hook, Ash Core Super, NYFG-8 Pike Pole, (1), Fire Hooks Unlimited, 10' Fiberglass, New Yorker Hook, Ash Core Super, NYFG-10 Pike Pole, (1), Fire Hooks Unlimited, 12' Fiberglass, National Hook, Ash Core, NHF-12 Pike Pole, (1), Fire Hooks Unlimited, 12' Fiberglass, New Yorker Hook, Ash Core Super, NYFG-12 Fol-da-Tank, 3000 Gallon, 22 oz. HPR, Aluminum Frame Low Level Strainer, Kochek 5" Pike Pole, (1), Fire Hooks Unlimited, 6' Steel, New York Roof Hook, RH-6 Discharge, Aerial Waterway, 4" (55', Squrt, TeleSqurt) Discharge, Aerial Waterway, 4" (75') Discharge, Aerial Waterway, 4" (100' MMA) Discharge, Aerial Waterway, 4", 5" Plumbing (85' MMP/100' MMP) Mounting Bracket, TFT, Portable Ground Base Auxiliary Pump, Waterous, PB-18-2515 Cooling Line, 3/8" Load Chart (100' SHD) Load Chart (125') Load Chart (105') Load Chart (75') Load Chart (55') Load Chart (UT 100') Load Chart (100' Tiller) Load Chart (100' RMP) Load Chart (85' RMP) Load Chart (100' MMP) Load Chart (85' MMP - 500/1500) Load Chart (100' MMA) Primer, Trident, AirPrime (3-Barrel), Remote Prime on. Aux Pump - Add. Act. In Cab Egress, Bolt-On, Short (75'/UT/105'/125') Folding Steps on Fly Section (UT 100'/100' Tiller) Ground Control System, Electric Over Hydraulic Controls, Rear Stabilizers, Lower Center Rear, Horizontal, Brushed Stainless Doors 120V Aerial Wiring (55') 120V Aerial Wiring (75') 120V Aerial Wiring (105') 120V Aerial Wiring (UT 100') 120V Aerial Wiring (125') 120V Aerial Wiring (100' RMP) 120V Aerial Wiring (85' RMP) 120V Aerial Wiring (100' MMP) 120V Aerial Wiring (85' MMP) 120V Aerial Wiring (100' MMA) 120V Aerial Wiring (100' SHD) OEM Chassis Preparations, Spartan MetroStar X Turntable Handrails, Knurled SS, Standard Turntable, (2) Openings (55'/75') Manifold, Waterous, Standard, Eclipse CAFS for Foam Pro System Turntable, Standard (105') Turntable Handrails, Ribbed Rubber SS, Standard Turntable, (2) Openings Turntable, Standard (125') Turntable, Officer's Side Cut-Off (UT 100') Manifold, Waterous, Standard, Eclipse CAFS for Advantus System Turntable Handrails, Knurled SS, Officer's Side Cut-Off Turntable, (2) Openings Turntable, Officer's Side Cut-Off (105') Turntable Handrails, Knurled SS, Officer's Side Cut-Off Turntable, (1) Opening (55'/75') Turntable, Officer's Side Cut-Off (55') Turntable Handrails, Ribbed Rubber SS, Officer's Side Cut-Off Turntable, (1) Opening (55'/75') Turntable Handrails, Ribbed Rubber SS, Officer's Side Cut-Off Turntable, (2) Openings (55')

008491 008495 008496 008499 008500 008505 008506 008507 008510 008514 008516 008523 008525 008551 008552 008553 008554 008555 008556 008557 008558 008560 008561 008567 008568 008569 008571 008572 008573 008574 008575 008576 008577 008606 008607 008608 008609 008610 008318 008321 008323 008325 008326 008328 008329 008330 008331 008332 008333 008334 008335 008336 008337 008341 008342 008343 008344 008345 008346 008347 008348 008349 008350 008351 008352 008353 008358 008359 008360 008361 008365 008368 008375 008377 008378 008379 008380 008381 008382 008383 008384 008387 008390 008398 008416 008419 008424 008435 008437 008440 008441 008449 008453 008454 008464 008465 008473 008474 008475 Turntable Handrails, Ribbed Rubber SS, Officer's Side Cut-Off Turntable, (2) Openings (75') Turntable Handrails, Ribbed Rubber SS, Standard Turntable, (2) Openings (55'/75') Turntable Handrails, Knurled SS, Standard Turntable, (3) Openings (85' MMP/100' MMP) Platform Hose Storage Box (1), 50' of 1-3/4" Hose Rope Rescue Package Turntable, Standard (85' MMP/100' MMP) Turntable, Officer's Side Cut-Off (75') Turntable, Standard (100' RMP) Turntable, Officer's Side Cut-Off (125') Turntable, Standard (85' RMP) Turntable, Standard (UT 100') Platform Design/Construction/Deck Surface, Rear Mount Platform, Dual Monitors Platform Design/Construction/Deck Surface, Mid Mount Platform, Dual Monitors Turntable, Standard (100' MMA) Turntable, Standard (55') Turntable Handrails, Ribbed Rubber SS, Officer's Side Cut-Off Turntable, (2) Openings Turntable Restraints, (2) Chains Turntable, Officer's Side Cut-Off (100' RMP) Turntable Restraints, (2) ManSaver Bars Turntable Handrails, Knurled SS, Officer's Side Cut-Off Turntable, (2) Openings (55') Turntable Handrails, Knurled SS, Standard Turntable, (2) Openings Turntable Restraint, (1) ManSaver Bar Turntable Restraint, (1) Chain Turntable, Officer's Side Cut-Off (85' RMP) Turntable Restraints, (2) ManSaver Bar and (1) Chain Turntable Handrails, Ribbed Rubber SS, Standard Turntable, (3) Openings (85' MMP/100' MMP) Stokes Basket Storage, Officer's Side Base Section, Retaining Strap (55'/75') Stokes Basket Storage, Officer's Side Base Section, Retaining Strap Hydraulic Pressure Filter, 3 Micron (Ladders) Platform Rappelling Arm, 500 lb, Dual Monitors Platform Parapet Ground Ladder Attachment, Dual Monitor Mid Mount Platforms Platform Parapet Ground Ladder Attachment, Dual Monitor Rear Mount Platforms Discharges (2), In Platform, 2-1/2", NST (Dual Monitor Platforms) Discharge (1), In Platform, 2-1/2", NST (Dual Monitor Platforms) Turntable, Standard (75') Exhause Mitigation Device, Chassis Supplied, OEM Installed Divider, Front Bumper Hosewell Tow Bar, Lifting, Front Bumper Cab Corners, Stainless Steel, Rear Cab, Chassis Supplied, OEM Installed Route Manual Moisture Ejector Cables, Chassis, Outside of Body, Pumper Alter Pump House, Spartan SMFD, For Six Batteries Body Striping, Aerial, 1"-4"-1", Low Angle Transition Four Gauge Cluster, Pump Panel, Chassis Supplied, OEM Wiring Light Tower Location, On Top of the Chassis Cab, Controls in L1 Cab Electrical, Non-Multiplex, Integrate with Multiplex Body Mounting Plate, On Engine Tunnel, Aluminum, Abraded Auxiliary Pump, Hale, HPX100-KBD24 Access/Ventilation Panel, Auxiliary Pump, Top Pump Module, Hinged, Tread Plate, Bar Grate, Rage Manifold, Hale, Standard, Rage Crosslays, Divided in Preconnect in Hose Bed, Two (2) 1-1/2", Rage Crosslay Cover, Hinged Tread Plate, Rage Discharges, Two (2), Front Bumper Both Sides, 1-1/2", Above Gravelshield, NST Refill System, Hale, EZ-Fill, Single System Pump Panel Lighting, Driver's Side Panel, LED, On-Scene Night Axe, Rage Master Gauges, Class 1, 3-1/2", Liquid Filled (No Bezel), psi -30-0-600 Body, 96" Wide, Rage, Single-Axle, Galvanneal, 12 Gauge Auxiliary Step, Below Rear Deck, Bar Grate Air Release and Drain Holes, All Compartments (Rage) Wheel Wells, Rear, Single Axle, Rage Fenderettes, (2), Rubber, Single Axle, Rub Rails, "C" Channel Design, Rage Storage Partition, (1), Adjustable, Aluminum, Abraded I-Zone Brackets Ladder Storage, Inside Hose Bed Storage Compartment, Painted Aluminum Doors Ladder, (1), Duo-Safety, 20' Three-Section Extension, 912-100 Electrical System, Sealed Switches, Rage Tail Lights, LED, Grote, SuperNova, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Casting Fog Lights, In Front Bumper Switch, Fog Lights, In Cab Scene Light, (1), 12V, Whelen, Surface Mount, LED M6 Series Gradient Scene Upper Zone A, Lightbar, Whelen, 54", Liberty LED, California Compliant Upper Zone C, Warning Lights (2), Whelen, LINZ6 LED, Red Both Sides Air Horn Activation, Steering Wheel High-Beam Flasher, Alternating Headlight Chassis Step and Fuel Tank Overlays, Partial, Bar Grate, Rage Rage Requirement, Fuel Tank Venting Rage Requirement, Exterior Trim Rage Requirement, Air Intake Screens Rage Requirement, Skid Plate Rage Requirement, Exhaust Modification Rage Requirement, Front Tow Eye Rage Requirement, Hose Roller Mounts Rage Requirement, Compartments, Under-Seat, Enclosed Front Bumper Extension, 16", Tread Plate Gravel Shield, IHC Shelf, Back of Engine Tunnel, Tread Plate Battery Charger, Kussmaul 1200 Battery Charger, Kussmaul 3510 Battery Charger, Chassis Supplied, OEM Installed EMS Compartment, Outside of Forward Facing Seat on Officer's Side EMS Compartment, Chest Style with Hinged Lift-up Door Center on Engine Tunnel EMS Compartment, Rear Facing Behind Driver's Seat EMS Compartment, Rear Facing Behind Officer's Seat Map Consoles, Two (2), (1) Each side of AC Unit Spotlight, In Cab, Chassis Supplied, OEM Installed, Handheld Body Striping, Pumper, Lap Doors, 4", Straight Around Perimeter Body Striping, Pumper, Lap Doors, 6", Straight Around Perimeter Body Striping, Pumper, Lap Doors, 1"-4"-1", Straight Around Perimeter Body Striping, Pumper, Lap Doors, 1"-6"-1", Straight Around Perimeter Body Striping, Pumper, 4", Straight Around Perimeter

008717 008725 008728 008730 008743 008744 008745 008747 008748 008749 008750 008751 008752 008753 008768 008771 008772 008773 008774 008775 008779 008781 008783 008785 008792 008793 008794 008795 008796 008797 008798 008799 008800 008801 008803 008804 008805 008806 008611 008612 008613 008614 008615 008616 008617 008618 008619 008620 008621 008622 008623 008624 008625 008626 008627 008628 008629 008631 008632 008633 008634 008635 008636 008637 008638 008639 008643 008648 008655 008669 008670 008671 008672 008673 008678 008679 008680 008689 008690 008691 008692 008693 008694 008695 008696 008697 008698 008699 008700 008701 008702 008703 008704 008705 008706 008707 008711 008712 008716 Body Striping, Pumper, 6", Straight Around Perimeter Body Striping, Pumper, Rollup Doors, 1"-4"-1", Straight Around Perimeter Body Striping, Pumper, Rollup Doors, 1"-6"-1", Straight Around Perimeter Body Striping, Pumper, Lap Doors, 4", High Angle Transition Body Striping, Pumper, Lap Doors, 6", High Angle Transition Body Striping, Pumper, Lap Doors, 1"-4"-1", High Angle Transition Body Striping, Pumper, Lap Doors, 1"-6"-1", High Angle Transition Body Striping, Pumper, Rollup Doors, 4", High Angle Transition Body Striping, Pumper, Rollup Doors, 6", High Angle Transition Body Striping, Pumper, Rollup Doors, 1"-4"-1", High Angle Transition Body Striping, Pumper, Rollup Doors, 1"-6"-1", High Angle Transition Body Striping, Pumper, Lap Doors, 4", Low Angle Transition Body Striping, Pumper, Lap Doors, 6", Low Angle Transition Body Striping, Pumper, Lap Doors, 1"-4"-1", Low Angle Transition Body Striping, Pumper, Lap Doors, 1"-6"-1", Low Angle Transition Body Striping, Pumper, Rollup Doors, 4", Low Angle Transition Body Striping, Pumper, Rollup Doors, 6", Low Angle Transition Body Striping, Pumper, Rollup Doors, 1"-4"-1", Low Angle Transition Body Striping, Pumper, Rollup Doors, 1"-6"-1", Low Angle Transition Body Striping, Pumper, Lap Doors, 4", S-Ribbon Transition with 3D Shadow Body Striping, Pumper, Lap Doors, 6", S-Ribbon Transition with 3D Shadow Body Striping, Pumper, Lap Doors, 1"-4"-1", S-Ribbon Transition with 3D Shadow Body Striping, Pumper, Lap Doors, 1"-6"-1", S-Ribbon Transition with 3D Shadow Body Striping, Pumper, Rollup Doors, 4", S-Ribbon Transition with 3D Shadow Body Striping, Pumper, Rollup Doors, 6", S-Ribbon Transition with 3D Shadow Body Striping, Pumper, Rollup Doors, 1"-4"-1", S-Ribbon Transition with 3D Shadow Body Striping, Pumper, Rollup Doors, 1"-6"-1", S-Ribbon Transition with 3D Shadow Body Striping, Pumper, Lap Doors, 4", Z Transition Ladder, (1), Duo-Safety, 45' Three-Section Extension with Stay Poles, 1525-A Monitor Safety Interlock/Stow Feature, With Light Body Striping, Pumper, Lap Doors, 6", Z Transition Body Striping, Pumper, Lap Doors, 1"-4"-1", Z Transition Body Striping, Pumper, Lap Doors, 1"-6"-1", Z Transition Body Striping, Pumper, Rollup Doors, 4", Z Transition Body Striping, Pumper, Rollup Doors, 6", Z Transition Body Striping, Pumper, Rollup Doors, 1"-4"-1", Z Transition Body Striping, Pumper, Rollup Doors, 1"-6"-1", Z Transition Body Striping, Aerial, Lap Doors, 4", Straight Around Perimeter Decal, Reflective, 6" Straight American Flag Body Striping, Aerial, Lap Doors, 6", Straight Around Perimeter Body Striping, Aerial, Lap Doors, 1"-4"-1", Straight Around Perimeter Body Striping, Aerial, Lap Doors, 1"-6"-1", Straight Around Perimeter Body Striping, Aerial, 4", Straight Around Perimeter Body Striping, Aerial, 6", Straight Around Perimeter Body Striping, Aerial, Rollup Doors, 1"-4"-1", Straight Around Perimeter Body Striping, Aerial, Rollup Doors, 1"-6"-1", Straight Around Perimeter Body Striping, Aerial, Lap Doors, 4", High Angle Transition Body Striping, Aerial, Lap Doors, 6", High Angle Transition Body Striping, Aerial, Lap Doors, 1"-4"-1", High Angle Transition Body Striping, Aerial, Lap Doors, 1"-6"-1", High Angle Transition Body Striping, Aerial, Rollup Doors, 4", High Angle Transition Body Striping, Aerial, Rollup Doors, 6", High Angle Transition Body Striping, Aerial, Rollup Doors, 1"-4"-1", High Angle Transition Sign, Reflective, Rear Lap Door, 'Keep Back 500 Feet' Body Striping, Aerial, Rollup Doors, 1"-6"-1", High Angle Transition Body Striping, Aerial, Lap Doors, 4", Low Angle Transition Body Striping, Aerial, Lap Doors, 6", Low Angle Transition Body Striping, Aerial, Lap Doors, 1"-4"-1", Low Angle Transition Flashlight, (1), Bright Star, Responder, Yellow, 500222, With Ni-Cad Battery and Quick Charger II Flashlight, (1), Pelican, Big Ed Rechargeable, Yellow, 3750, with 3760F Charger Flashlight, (1), Streamlight, LiteBox, 8 Watt, Orange, 45107, Vehicle Mount System Flashlight, (1), Streamlight, Fire Vulcan, Orange, 44401, Vehicle Mount System Body Striping, Aerial, Lap Doors, 1"-6"-1", Low Angle Transition Body Striping, Aerial, Rollup Doors, 4", Low Angle Transition Turn Signals, (2) in Rub Rail, LED, Truck-Lite, Model 21 Flashlight, (1) Set, Streamlight, Survivor LED, Yellow, 90513, Five (5) Lights, with 90400 Five (5) Bank Charger Flashlight, (1) Set, Streamlight, Survivor LED, Orange, 90503, Five (5) Lights, with 90400 Five (5) Bank Charger Flashlight, (1) Set, Streamlight, Survivor LED, Black, 90523, Five (5) Lights, with 90400 Five (5) Bank Charger Ladder Storage, Hydraulic Equipment Rack, Officer's Side, Painted Cover and Shield, Switch on Pump Panel Ladder Storage, Hydraulic Equipment Rack, Driver's Side, Painted Cover and Shield, Switch on Pump Panel Ladder Storage, Hydraulic Equipment Rack, Officer's Side, Tread Plate Cover, Switch on Pump Panel Ladder Storage, Hydraulic Equipment Rack, Driver's Side, Tread Plate Cover, Switch on Pump Panel Ladder Storage, Dual Hydraulic Equipment Racks, Painted Covers, Switches on Pump Panels Ladder Storage, Dual Hydraulic Equipment Racks, Painted Covers and Shields, Switches on Pump Panels Ladder Storage, Dual Hydraulic Equipment Racks, Tread Plate Covers, Switches on Pump Panels Stabilizer Arm Warning Lights (8), Whelen, 5G Series Super LED, Red Sub Frame, GS-36, Hot-Dip Galvanized Steel, Aerial (75' Single-Axle) Sub Frame, GS-36, Hot-Dip Galvanized Steel, Aerial (55') Sub Frame, GS-36, Hot-Dip Galvanized Steel, Aerial (85' RMP/105') Sub Frame, GS-36, Hot-Dip Galvanized Steel, Aerial (100' RMP/125') Sub Frame, GS-36, Hot-Dip Galvanized Steel, Aerial (85' MMP/100' MMP) Sub-Frame, Hot-Dip Galvanized, Custom Pumpers, Stainless Steel Body Generator, Hydraulic, Harrison, 6kW, MCR, FRC Frog Display Generator, Hydraulic, Harrison, 8kW, MCR, FRC Frog Display Generator, Hydraulic, Harrison, 10kW, MCR, FRC Frog Display Aerial Ladder Paint Color, White, PPG# FDGH-2185, 55' Aerial Ladder Paint Color, White, PPG# FDGH-2185, 75' Aerial Ladder Paint Color, White, PPG# FDGH-2185, 105', 85' RMP Aerial Ladder Paint Color, White, PPG# FDGH-2185, 85' MMP Aerial Ladder Paint Color, White, PPG# FDGH-2185, 100' MMP Aerial Ladder Paint Color, White, PPG# FDGH-2185, 125' Aerial Ladder Paint Color, White, PPG# FDGH-2185, 100' RMP Aerial Ladder Paint Color, White, PPG# FDGH-8717, 55' Aerial Ladder Paint Color, White, PPG# FDGH-8717, 75' Aerial Ladder Paint Color, White, PPG# FDGH-8717, 105', 85' RMP Body Striping, Aerial, Rollup Doors, 6", Low Angle Transition Aerial Ladder Paint Color, White, PPG# FDGH-8717, 85' MMP Aerial Ladder Paint Color, White, PPG# FDGH-8717, 100' MMP Aerial Ladder Paint Color, White, PPG# FDGH-8717, 125'

008868 008869 008870 008871 008872 008873 008874 008875 008876 008877 008878 008879 008880 008881 008882 008883 008884 008885 008886 008887 008888 008889 008890 008891 008892 008893 008894 008895 008896 008897 008898 008899 008900 008901 008902 008903 008904 008905 008807 008808 008809 008810 008811 008812 008813 008814 008815 008816 008817 008818 008819 008820 008821 008822 008823 008824 008825 008826 008827 008828 008829 008830 008831 008832 008833 008834 008835 008836 008837 008838 008839 008840 008841 008842 008843 008844 008845 008846 008847 008848 008849 008850 008851 008852 008853 008854 008855 008856 008857 008858 008859 008860 008861 008862 008863 008864 008865 008866 008867 Aerial Ladder Paint Color, White, PPG# FDGH-8717, 100' RMP Aerial Ladder Paint Color, Silver (Metallic), PPG# FBCH-35913, 55' Aerial Ladder Paint Color, Silver (Metallic), PPG# FBCH-35913, 75' Aerial Ladder Paint Color, Silver (Metallic), PPG# FBCH-35913, 105', 85' RMP Aerial Ladder Paint Color, Silver (Metallic), PPG# FBCH-35913, 85' MMP Aerial Ladder Paint Color, Silver (Metallic), PPG# FBCH-35913, 100' MMP Aerial Ladder Paint Color, Silver (Metallic), PPG# FBCH-35913, 125' Aerial Ladder Paint Color, Silver (Metallic), PPG# FBCH-35913, 100' RMP Aerial Ladder Paint Color, Black, PPG# FDGH-9000, 55' Aerial Ladder Paint Color, Black, PPG# FDGH-9000, 75' Aerial Ladder Paint Color, Black, PPG# FDGH-9000, 75' RMA, 105' RMA, 85' RMP Aerial Ladder Paint Color, Black, PPG# FDG-9000, 125' Aerial Ladder Paint Color, Black, PPG# FDGH-9000, 125' RMA, 100' RMP, 85'MMP, 100'MMP Aerial Ladder Paint Color, Black, PPG# FDG-9000, 125' Aerial Ladder Paint Color, Black, PPG# FDG-9000, 100' RMP Aerial Ladder Paint Color, Gray, PPG# FDGH-307480, 55' Aerial Ladder Paint Color, Gray, PPG# FDGH-307480, 75' Aerial Ladder Paint Color, Gray, PPG# FDGH-307480, 105', 85' RMP Aerial Ladder Paint Color, Gray, PPG# FDGH-307480, 85' MMP Aerial Ladder Paint Color, Gray, PPG# FDGH-307480, 100' MMP Aerial Ladder Paint Color, Gray, PPG# FDGH-307480, 125' Aerial Ladder Paint Color, Gray, PPG# FDGH-307480, 100' RMP Platform Paint Color, White, PPG# FDGH-8717 Platform Paint Color, Silver, PPG# FBCH-35913, Metallic Platform Paint Color, Black, PPG# FDGH-9000 Platform Paint Color, Gray, PPG# FDGH-307480 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-3279 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-3464 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-4311-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-70030-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-70358 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-70436 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-70853 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-708760 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-71096-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-71528 "Prime" Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-71528-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-71654 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-71660-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-71663 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-71663-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-71665 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-71698-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-72626-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-72704-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-73787-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-73791-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-73841 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-74013 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-74022 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-74338 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-74787-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-75078-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-75374 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-75380 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-75380-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-75381 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-75481 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-75498 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-75664 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-76906 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-77721 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-77723 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-907112-ALT Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-911612 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-911655 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-911659 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-911664 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-912814 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-913787 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-923516 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-926234 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-926900 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-928957 Body Paint Color, Pumper, Single Tone, Red, PPG# FBCH-934434 Body Paint Color, Pumper, Single Tone, Black, PPG# FBCH-9000 Body Paint Color, Pumper, Single Tone, Black, PPG# FBCH-911601 Body Paint Color, Pumper, Single Tone, Blue, PPG# FBCH-18483, Metallic Body Paint Color, Pumper, Single Tone, Lime, PPG# FBCH-46172 Body Paint Color, Pumper, Single Tone, Lime, PPG# FBCH-82027 Body Paint Color, Pumper, Single Tone, Lime, PPG# FBCH-911012 Body Paint Color, Pumper, Single Tone, Lime, PPG# FBCH-914751 Body Paint Color, Pumper, Single Tone, Silver, PPG# FBCH-302950, Metallic Body Paint Color, Pumper, Single Tone, Silver, PPG# FBCH-35498, Metallic Body Paint Color, Pumper, Single Tone, White, PPG# FBCH-2185 Body Paint Color, Pumper, Single Tone, White, PPG# FBCH-8000 Body Paint Color, Pumper, Single Tone, White, PPG# FBCH-8717 Body Paint Color, Pumper, Single Tone, White, PPG# FBCH-90138 Body Paint Color, Pumper, Single Tone, Yellow, PPG# FBCH-81485-ALT Body Paint Color, Pumper, Single Tone, Yellow, PPG# FBCH-81533 Body Paint Color, Pumper, Single Tone, Yellow, PPG# FBCH-83661 Body Paint Color, Pumper, Single Tone, Yellow, PPG# FBCH-911653 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-3279 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-3464 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-4311-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-70030-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-70358 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-70436 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-70853

008967 008968 008969 008970 008971 008972 008973 008974 008975 008976 008977 008978 008979 008980 008981 008982 008983 008984 008985 008986 008987 008988 008989 008990 008991 008992 008993 008994 008995 008996 008997 008998 008999 009000 009001 009002 009003 009004 008906 008907 008908 008909 008910 008911 008912 008913 008914 008915 008916 008917 008918 008919 008920 008921 008922 008923 008924 008925 008926 008927 008928 008929 008930 008931 008932 008933 008934 008935 008936 008937 008938 008939 008940 008941 008942 008943 008944 008945 008946 008947 008948 008949 008950 008951 008952 008953 008954 008955 008956 008957 008958 008959 008960 008961 008962 008963 008964 008965 008966 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-708760 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-71096-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-71528 "Prime" Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-71528-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-71654 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-71660-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-71663 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-71663-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-71665 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-71698-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-72626-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-72704-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-73787-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-73791-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-73841 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-74013 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-74022 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-74338 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-74787-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-75078-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-75374 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-75380 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-75380-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-75381 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-75481 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-75498 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-75664 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-76906 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-77721 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-77723 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-907112-ALT Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-911612 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-911655 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-911659 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-911664 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-912814 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-913787 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-923516 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-926234 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-926900 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-928957 Body Paint Color, Aerial, Single Tone, Red, PPG# FBCH-934434 Body Paint Color, Aerial, Single Tone, Black, PPG# FBCH-9000 Body Paint Color, Aerial, Single Tone, Black, PPG# FBCH-911601 Body Paint Color, Aerial, Single Tone, Blue, PPG# FBCH-18483, Metallic Body Paint Color, Aerial, Single Tone, Lime, PPG# FBCH-46172 Body Paint Color, Aerial, Single Tone, Lime, PPG# FBCH-82027 Body Paint Color, Aerial, Single Tone, Lime, PPG# FBCH-911012 Body Paint Color, Aerial, Single Tone, Lime, PPG# FBCH-914751 Body Paint Color, Aerial, Single Tone, Silver, PPG# FBCH-302950, Metallic Body Paint Color, Aerial, Single Tone, Silver, PPG# FBCH-35498, Metallic Body Paint Color, Aerial, Single Tone, White, PPG# FBCH-2185 Body Paint Color, Aerial, Single Tone, White, PPG# FBCH-8000 Body Paint Color, Aerial, Single Tone, White, PPG# FBCH-8717 Body Paint Color, Aerial, Single Tone, White, PPG# FBCH-90138 Body Paint Color, Aerial, Single Tone, Yellow, PPG# FBCH-81485-ALT Body Paint Color, Aerial, Single Tone, Yellow, PPG# FBCH-81533 Body Paint Color, Aerial, Single Tone, Yellow, PPG# FBCH-83661 Body Paint Color, Aerial, Single Tone, Yellow, PPG# FBCH-911653 Body Paint Color, Pumper, Single Tone, Unknown Paint Color, Metallic Body Paint Color, Pumper, Single Tone, Unknown Paint Color, Non-Metallic Body Paint Color, Aerial, Single Tone, Unknown Paint Color, Metallic Body Paint Color, Aerial, Single Tone, Unknown Paint Color, Non-Metallic Body Paint Color, Pumper, Two-Tone, Upper, Black, PPG# FBCH-9000 Body Paint Color, Pumper, Two-Tone, Upper, Black, PPG# FBCH-911601 Body Paint Color, Pumper, Two-Tone, Upper, Blue, PPG# FBCH-18483, Metallic Body Paint Color, Pumper, Two-Tone, Upper, Lime, PPG# FBCH-46172 Body Paint Color, Pumper, Two-Tone, Upper, Lime, PPG# FBCH-82027 Body Paint Color, Pumper, Two-Tone, Upper, Lime, PPG# FBCH-911012 Body Paint Color, Pumper, Two-Tone, Upper, Lime, PPG# FBCH-914751 Body Paint Color, Pumper, Two-Tone, Upper, Silver, PPG# FBCH-302950, Metallic Body Paint Color, Pumper, Two-Tone, Upper, Silver, PPG# FBCH-35498, Metallic Body Paint Color, Pumper, Two-Tone, Upper, Unknown Paint Color, Metallic Body Paint Color, Pumper, Two-Tone, Upper, Unknown Paint Color, Non-Metallic Body Paint Color, Pumper, Two-Tone, Upper, White, PPG# FBCH-2185 Body Paint Color, Pumper, Two-Tone, Upper, White, PPG# FBCH-8000 Body Paint Color, Pumper, Two-Tone, Upper, White, PPG# FBCH-8717 Body Paint Color, Pumper, Two-Tone, Upper, White, PPG# FBCH-90138 Body Paint Color, Pumper, Two-Tone, Upper, Yellow, PPG# FBCH-81485-ALT Body Paint Color, Pumper, Two-Tone, Upper, Yellow, PPG# FBCH-81533 Body Paint Color, Pumper, Two-Tone, Upper, Yellow, PPG# FBCH-83661 Body Paint Color, Pumper, Two-Tone, Upper, Yellow, PPG# FBCH-911653 Body Paint Color, Aerial, Two-Tone, Upper, Black, PPG# FBCH-9000 Body Paint Color, Aerial, Two-Tone, Upper, Black, PPG# FBCH-911601 Body Paint Color, Aerial, Two-Tone, Upper, Blue, PPG# FBCH-18483, Metallic Body Paint Color, Aerial, Two-Tone, Upper, Lime, PPG# FBCH-46172 Body Paint Color, Aerial, Two-Tone, Upper, Lime, PPG# FBCH-82027 Body Paint Color, Aerial, Two-Tone, Upper, Lime, PPG# FBCH-911012 Body Paint Color, Aerial, Two-Tone, Upper, Lime, PPG# FBCH-914751 Body Paint Color, Aerial, Two-Tone, Upper, Silver, PPG# FBCH-302950, Metallic Body Paint Color, Aerial, Two-Tone, Upper, Silver, PPG# FBCH-35498, Metallic Body Paint Color, Aerial, Two-Tone, Upper, Unknown Paint Color, Metallic Body Paint Color, Aerial, Two-Tone, Upper, Unknown Paint Color, Non-Metallic Body Paint Color, Aerial, Two-Tone, Upper, White, PPG# FBCH-2185 Body Paint Color, Aerial, Two-Tone, Upper, White, PPG# FBCH-8000 Body Paint Color, Aerial, Two-Tone, Upper, White, PPG# FBCH-8717 Body Paint Color, Aerial, Two-Tone, Upper, White, PPG# FBCH-90138 Body Paint Color, Aerial, Two-Tone, Upper, Yellow, PPG# FBCH-81485-ALT Body Paint Color, Aerial, Two-Tone, Upper, Yellow, PPG# FBCH-81533

009066 009067 009068 009069 009070 009071 009072 009073 009074 009075 009076 009077 009078 009079 009081 009082 009083 009084 009085 009086 009087 009088 009089 009090 009091 009092 009093 009094 009095 009096 009097 009098 009099 009100 009101 009102 009103 009104 009005 009006 009007 009008 009009 009010 009011 009012 009013 009014 009015 009016 009017 009018 009019 009020 009021 009022 009023 009024 009025 009026 009027 009028 009029 009030 009031 009032 009033 009034 009035 009036 009037 009038 009039 009040 009041 009042 009043 009044 009045 009046 009047 009048 009049 009050 009051 009052 009053 009054 009055 009056 009057 009058 009059 009060 009061 009062 009063 009064 009065 Body Paint Color, Aerial, Two-Tone, Upper, Yellow, PPG# FBCH-83661 Body Paint Color, Aerial, Two-Tone, Upper, Yellow, PPG# FBCH-911653 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-3279 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-3464 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-4311-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-70030-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-70358 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-70436 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-70853 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-708760 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-71096-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-71528 "Prime" Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-71528-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-71654 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-71660-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-71663 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-71663-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-71665 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-71698-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-72626-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-72704-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-73787-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-73791-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-73841 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-74013 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-74022 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-74338 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-74787-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-75078-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-75374 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-75380 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-75380-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-75381 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-75481 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-75498 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-75664 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-76906 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-77721 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-77723 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-907112-ALT Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-911612 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-911655 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-911659 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-911664 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-912814 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-913787 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-923516 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-926234 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-926900 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-928957 Body Paint Color, Pumper, Two-Tone, Lower, Red, PPG# FBCH-934434 Body Paint Color, Pumper, Two-Tone, Lower, Black, PPG# FBCH-9000 Body Paint Color, Pumper, Two-Tone, Lower, Black, PPG# FBCH-911601 Body Paint Color, Pumper, Two-Tone, Lower, Blue, PPG# FBCH-18483, Metallic Body Paint Color, Pumper, Two-Tone, Lower, Lime, PPG# FBCH-46172 Body Paint Color, Pumper, Two-Tone, Lower, Lime, PPG# FBCH-82027 Body Paint Color, Pumper, Two-Tone, Lower, Lime, PPG# FBCH-911012 Body Paint Color, Pumper, Two-Tone, Lower, Lime, PPG# FBCH-914751 Body Paint Color, Pumper, Two-Tone, Lower, Silver, PPG# FBCH-302950, Metallic Body Paint Color, Pumper, Two-Tone, Lower, Silver, PPG# FBCH-35498, Metallic Body Paint Color, Pumper, Two-Tone, Lower, Unknown Paint Color, Metallic Body Paint Color, Pumper, Two-Tone, Lower, Unknown Paint Color, Non-Metallic Body Paint Color, Pumper, Two-Tone, Lower, White, PPG# FBCH-2185 Body Paint Color, Pumper, Two-Tone, Lower, White, PPG# FBCH-8000 Non-Painted 304 Stainless Brushed Finish Body Paint Color, Pumper, Two-Tone, Lower, White, PPG# FBCH-8717 Body Paint Color, Pumper, Two-Tone, Lower, White, PPG# FBCH-90138 Body Paint Color, Pumper, Two-Tone, Lower, Yellow, PPG# FBCH-81485-ALT Body Paint Color, Pumper, Two-Tone, Lower, Yellow, PPG# FBCH-81533 Body Paint Color, Pumper, Two-Tone, Lower, Yellow, PPG# FBCH-83661 Body Paint Color, Pumper, Two-Tone, Lower, Yellow, PPG# FBCH-911653 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-3279 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-3464 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-4311-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-70030-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-70358 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-70436 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-70853 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-708760 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-71096-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-71528 "Prime" Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-71528-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-71654 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-71660-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-71663 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-71663-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-71665 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-71698-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-72626-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-72704-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-73787-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-73791-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-73841 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-74013 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-74022 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-74338 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-74787-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-75078-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-75374

009166 009167 009168 009169 009170 009171 009172 009173 009174 009175 009176 009177 009178 009181 009182 009183 009184 009185 009186 009187 009188 009189 009190 009191 009192 009193 009194 009195 009196 009197 009198 009199 009200 009201 009202 009203 009204 009205 009105 009106 009107 009108 009109 009110 009111 009112 009113 009114 009115 009116 009117 009118 009119 009120 009121 009122 009123 009124 009125 009126 009127 009128 009129 009130 009131 009132 009133 009134 009135 009136 009137 009138 009139 009140 009141 009142 009143 009144 009145 009146 009147 009148 009149 009150 009151 009152 009153 009154 009155 009156 009157 009158 009159 009160 009161 009162 009163 009164 009165 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-75380 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-75380-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-75381 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-75481 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-75498 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-75664 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-76906 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-77721 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-77723 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-907112-ALT Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-911612 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-911655 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-911659 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-911664 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-912814 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-913787 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-923516 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-926234 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-926900 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-928957 Body Paint Color, Aerial, Two-Tone, Lower, Red, PPG# FBCH-934434 Body Paint Color, Aerial, Two-Tone, Lower, Black, PPG# FBCH-9000 Body Paint Color, Aerial, Two-Tone, Lower, Black, PPG# FBCH-911601 Body Paint Color, Aerial, Two-Tone, Lower, Blue, PPG# FBCH-18483, Metallic Body Paint Color, Aerial, Two-Tone, Lower, Lime, PPG# FBCH-46172 Body Paint Color, Aerial, Two-Tone, Lower, Lime, PPG# FBCH-82027 Body Paint Color, Aerial, Two-Tone, Lower, Lime, PPG# FBCH-911012 Body Paint Color, Aerial, Two-Tone, Lower, Lime, PPG# FBCH-914751 Body Paint Color, Aerial, Two-Tone, Lower, Silver, PPG# FBCH-302950, Metallic Body Paint Color, Aerial, Two-Tone, Lower, Silver, PPG# FBCH-35498, Metallic Body Paint Color, Aerial, Two-Tone, Lower, Unknown Paint Color, Metallic Body Paint Color, Aerial, Two-Tone, Lower, Unknown Paint Color, Non-Metallic Body Paint Color, Aerial, Two-Tone, Lower, White, PPG# FBCH-2185 Body Paint Color, Aerial, Two-Tone, Lower, White, PPG# FBCH-8000 Body Paint Color, Aerial, Two-Tone, Lower, White, PPG# FBCH-8717 Body Paint Color, Aerial, Two-Tone, Lower, White, PPG# FBCH-90138 Body Paint Color, Aerial, Two-Tone, Lower, Yellow, PPG# FBCH-81485-ALT Body Paint Color, Aerial, Two-Tone, Lower, Yellow, PPG# FBCH-81533 Body Paint Color, Aerial, Two-Tone, Lower, Yellow, PPG# FBCH-83661 Body Paint Color, Aerial, Two-Tone, Lower, Yellow, PPG# FBCH-911653 Extinguisher Compartment, Driver's Side, Full Width, LED Lighting, Extinguisher Storage Only Extinguisher Compartment, Driver's Side, Full Width, LED Lighting, Extinguisher and Hard Suction Hose Storage Extinguisher Compartment, Driver's Side, Full Width, LED Lighting, Extinguisher and Ground Ladders, (2) Pike Poles, and (1) Hard Hose Storage Extinguisher Compartment, Driver's Side, Full Width, LED Lighting, Extinguisher and Pike Pole and Attic Ladder Storage Extinguisher Compartment, Driver's Side, Full Width, LED Lighting, Extinguisher and Tool Storage Extinguisher Compartment, Officer's Side, Full Width, LED Lighting, Extinguisher Storage Only Extinguisher Compartment, Officer's Side, Full Width, LED Lighting, Extinguisher and Hard Suction Hose Storage Extinguisher Compartment, Officer's Side, Full Width, LED Lighting, Extinguisher and Ground Ladder, (2) Pike Poles, and (1) Hard Hose Storage Extinguisher Compartment, Officer's Side, Full Width, LED Lighting, Extinguisher and Pike Pole and Attic Ladder Storage Extinguisher Compartment, Officer's Side, Full Width, LED Lighting, Extinguisher and Tool Storage Hatch Compartment, Driver's Side, 2-Door, Centered Bulkhead, Grote LED Lighting Hatch Compartment, Driver's Side, 2-Door, Bulkhead Divider, On-Scene Access LED Lighting Interior Cab Door Striping, Chevron Reflective Striping, 2-Door Interior Cab Door Striping, Chevron Reflective Striping, 4-Door Sign, Reflective, Rear Rollup Door, 'Keep Back 500 Feet' Sign, Reflective, Rear Rollup Door, 'Keep Back 150 Metres' Pinstriping, Accent Stripe, Arrow Stripe End, 1/8", White Pinstriping, Accent Stripe, Arrow Stripe End, 1/8", Blue Pinstriping, Accent Stripe, Arrow Stripe End, 1/4", White Pinstriping, Accent Stripe, Arrow Stripe End, 1/4", Blue Body Paint, Single Tone, Aerial, Aluminum Material Body Paint, Two-Tone, Aerial, Aluminum Material Body Paint, Single Tone, Aerial, 409 Stainless Steel Material Body Paint, Two-Tone, Aerial, 409 Stainless Steel Material Body Paint, Single Tone, Aerial, 304 Stainless Steel Material Body Paint, Two-Tone, Aerial, 304 Stainless Steel Material Body Paint, Single Tone, Pumper, Aluminum Material Body Paint, Two-Tone, Pumper, Aluminum Material Body Paint, Single Tone, Pumper, Galvanneal Material Body Paint, Two-Tone, Pumper, Galvanneal Material Body Paint, Single Tone, Pumper, 409 Stainless Steel Material Body Paint, Two-Tone, Pumper, 409 Stainless Steel Material Body Paint, Single Tone, Pumper, 304 Stainless Steel Material Body Paint, Two-Tone, Pumper, 304 Stainless Steel Material Pike Pole Brackets, (2), Zico Quic-Lift Ladder Rack (Alco-Lite) Pike Pole Brackets, (2), Zico Quic-Lift Ladder Rack (Duo-Safety) Pike Pole Tubes, (2), Fire Extinguisher Compartment, Driver's Side Pike Pole Tubes, (2), Fire Extinguisher Compartment, Officer's Side Pike Pole Tubes, (2), Hard Suction Hose Storage Rack Pike Pole Tubes, (2), Hard Suction Hose Enclosed Cmpt, Driver's Side Pike Pole Tubes, (2), Hard Suction Hose Enclosed Cmpt, Officer's Side Hatch Compartment, Driver's Side, 2-Door, Bulkhead Divider, On-Scene Night Axe LED Lighting Hatch Compartment, Driver's Side, 3-Door, Grote LED Lighting Hatch Compartment, Driver's Side, 3-Door, On-Scene Access LED Lighting Hatch Compartment, Driver's Side, 3-Door, Bulkhead Dividers, On-Scene Night Axe LED Lighting Pike Pole Tubes, (2), Hydraulic Equipment Rack, Driver's Side Hatch Compartment, Officer's Side, 2-Door, Centered Bulkhead, Grote LED Lighting Hatch Compartment, Officer's Side, 2-Door, Bulkhead Divider, On-Scene Access LED Lighting Hatch Compartment, Officer's Side, 2-Door, Bulkhead Divider, On-Scene Night Axe LED Lighting Hatch Compartment, Officer's Side, 3-Door, Bulkhead Dividers, Grote LED Lighting Hatch Compartment, Officer's Side, 3-Door, Bulkhead Dividers, On-Scene Access LED Lighting Hatch Compartment, Officer's Side, 3-Door, Evenly Spaced Bulkheads, On-Scene Night Axe LED Lighting Pike Pole Tubes, (2), Hydraulic Equipment Rack, Officer's Side Rear Stabilizer Compartments, Lap Doors, On-Scene Access LED Lighting, No Tiles Rear Stabilizer Compartments, Lap Doors, On-Scene Access LED Lighting, Dri-Dek Tiles Rear Stabilizer Compartments, Lap Doors, On-Scene Access LED Lighting, Turtle Tiles Rear Stabilizer Compartments, Lap Doors, On-Scene Night Axe LED Lighting, No Tiles Rear Stabilizer Compartments, Lap Doors, On-Scene Night Axe LED Lighting, Dri-Dek Tiles Rear Stabilizer Compartments, Lap Doors, On-Scene Night Axe LED Lighting, Turtle Tiles

009269 009270 009271 009272 009273 009274 009275 009276 009277 009278 009279 009280 009281 009282 009283 009284 009285 009286 009287 009288 009289 009290 009291 009292 009293 009294 009295 009296 009297 009298 009299 009300 009301 009302 009303 009304 009305 009306 009206 009207 009208 009209 009210 009211 009212 009213 009214 009215 009216 009217 009218 009219 009220 009221 009222 009223 009224 009225 009226 009227 009228 009231 009232 009233 009234 009235 009236 009237 009238 009239 009240 009241 009242 009243 009244 009245 009246 009247 009248 009249 009250 009251 009252 009253 009254 009255 009256 009257 009258 009259 009260 009261 009262 009263 009264 009265 009266 009267 009268 Ladder Storage, Hydraulic Equipment Rack, Officer's Side, Painted Cover, Switch on Rear Ladder Storage, Hydraulic Equipment Rack, Driver's Side, Painted Cover, Switch on Rear Ladder Storage, Hydraulic Equipment Rack, Officer's Side, Painted Cover and Shield, Switch on Rear Ladder Storage, Hydraulic Equipment Rack, Driver's Side, Painted Cover and Shield, Switch on Rear Panel Ladder Storage, Hydraulic Equipment Rack, Officer's Side, Tread Plate Cover, Switch on Rear Ladder Storage, Hydraulic Equipment Rack, Driver's Side, Tread Plate Cover, Switch on Rear Ladder Storage, Dual Hydraulic Equipment Racks, Painted Covers, Switches on Rear Ladder Storage, Dual Hydraulic Equipment Racks, Painted Covers and Shields, Switches on Rear Ladder Storage, Dual Hydraulic Equipment Racks, Tread Plate Covers, Switches on Rear Hydraulic Equipment Rack Attachment, Driver's Side, Ground Ladders, Pike Poles Hydraulic Equipment Rack Attachment, Officer's Side, Ground Ladders, Pike Poles Pike Pole Tubes, (2), Ladder Storage Above Low Sides, Mounted on Catwalk, Driver's Side Pike Pole Tubes, (2), Ladder Storage Above Low Sides, Mounted on Catwalk, Officer's Side Pike Pole Tubes, (2), In Ladder Storage Compartment Pike Pole Tubes, (3), Hydraulic Equipment Rack, Driver's Side Pike Pole Tubes, (3), Hydraulic Equipment Rack, Officer's Side Pike Pole Tubes, (3), In Ladder Storage Compartment Pike Pole Storage, In Upper Portion of Torque Box, (6) Tubes Pike Pole Tray, (1), Hard Suction Hose Enclosed Compartment, Driver's Side Pike Pole Tray, (1), Hard Suction Hose Enclosed Compartment, Officer's Side Pike Pole Storage, In Upper Portion of Torque Box, (2) Trays Ladder Storage, Above Low Sides, Officer's Side, Zico Quic-Lift Access System (Only 2-Section Extension and Roof Ladders) Ladder Storage, Above Low Sides, Driver's Side, Zico Quic-Lift Access System (Only 2-Section Extension and Roof Ladders) Fol-da-Tank Storage, 2100 Gallon, Above Driver's Side Low Sides, Stainless Steel Fold-Down Rack Fol-da-Tank Storage, 2100 Gallon, Above Officer's Side Low Sides, Stainless Steel Fold-Down Rack Fol-da-Tank Storage, 2100 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt, Rear Door Fol-da-Tank Storage, 2100 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt, Rear Straps Fol-da-Tank Storage, 2100 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt, Rear Door Fol-da-Tank Storage, 2100 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt, Rear Straps Hydraulic Equipment Rack Attachment, Driver's Side, 2100 Gallon Fol-Da-Tank, Tread Plate Cmpt, Rear Door Hydraulic Equipment Rack Attachment, Driver's Side, 2100 Gallon Fol-Da-Tank, Tread Plate Cmpt, Rear Straps Hydraulic Equipment Rack Attachment, Officer's Side, 2100 Gallon Fol-Da-Tank, Tread Plate Cmpt, Rear Door Hydraulic Equipment Rack Attachment, Officer's Side, 2100 Gallon Fol-Da-Tank, Tread Plate Cmpt, Rear Straps Fol-da-Tank Storage, 2100 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Door Fol-da-Tank Storage, 2100 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Straps Fol-da-Tank Storage, 2100 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Door Fol-da-Tank Storage, 2100 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Straps Fol-da-Tank Storage, 2500 Gallon, Above Driver's Side Low Sides, Stainless Steel Fold-Down Rack Fol-da-Tank Storage, 2500 Gallon, Above Officer's Side Low Sides, Stainless Steel Fold-Down Rack Fol-da-Tank Storage, 2500 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt, Rear Door Fol-da-Tank Storage, 2500 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt, Rear Straps Fol-da-Tank Storage, 2500 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt, Rear Door Fol-da-Tank Storage, 2500 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt, Rear Straps Hydraulic Equipment Rack Attachment, Driver's Side, 2500 Gallon Fol-Da-Tank, Tread Plate Cmpt, Rear Door Hydraulic Equipment Rack Attachment, Driver's Side, 2500 Gallon Fol-Da-Tank, Tread Plate Cmpt, Rear Straps Hydraulic Equipment Rack Attachment, Officer's Side, 2500 Gallon Fol-Da-Tank, Tread Plate Cmpt, Rear Door Hydraulic Equipment Rack Attachment, Officer's Side, 2500 Gallon Fol-Da-Tank, Tread Plate Cmpt, Rear Straps Fol-da-Tank Storage, 2500 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Door Fol-da-Tank Storage, 2500 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Straps Fol-da-Tank Storage, 2500 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Door Fol-da-Tank Storage, 2500 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt with Hose, Rear Straps Fol-da-Tank Storage, 3000 Gallon, Above Driver's Side Low Sides, Stainless Steel Fold-Down Rack Fol-da-Tank Storage, 3000 Gallon, Above Officer's Side Low Sides, Stainless Steel Fold-Down Rack Fol-da-Tank Storage, 3000 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt, Rear Door Fol-da-Tank Storage, 3000 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt, Rear Straps Fol-da-Tank Storage, 3000 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt, Rear Door Fol-da-Tank Storage, 3000 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt, Rear Straps Fol-da-Tank Storage, 3000 Gallon, Driver's Side Equipment Rack, Tread Plate Cmpt (Painted Cover/Rear Switch), Rear Door Fol-da-Tank Storage, 3000 Gallon, Driver's Side Equipment Rack, Tread Plate Cmpt (Painted Cover/Rear Switch), Rear Straps Fol-da-Tank Storage, 3000 Gallon, Officer's Side Equipment Rack, Tread Plate Cmpt (Painted Cover/Rear Switch), Rear Door Fol-da-Tank Storage, 3000 Gallon, Officer's Side Equipment Rack, Tread Plate Cmpt (Painted Cover/Rear Switch), Rear Straps Fol-da-Tank Storage, 3000 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Door Fol-da-Tank Storage, 3000 Gallon, Above Driver's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Straps Fol-da-Tank Storage, 3000 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Door Fol-da-Tank Storage, 3000 Gallon, Above Officer's Side Low Sides, Tread Plate Cmpt with Hoist, Rear Straps Hard Suction Hose Storage, One (1) Hose, Above Driver's Side High Cmpt, 'V' Trough (Abraded), Retaining Straps Hard Suction Hose Storage, One (1) Hose, Above Driver's Side Low Cmpt, 'V' Trough (Abraded), Retaining Straps Hard Suction Hose Storage, One (1) Hose, Above Officer's Side High Cmpt, 'V' Trough (Abraded), Retaining Straps Hard Suction Hose Storage, One (1) Hose, Above Officer's Side Low Cmpt, 'V' Trough (Abraded), Retaining Straps Hard Suction Hose Storage, One (1) Hose, Above Driver's Side High Cmpt, 'V' Trough (Painted), Retaining Straps Hard Suction Hose Storage, One (1) Hose, Above Driver's Side Low Cmpt, 'V' Trough (Painted), Retaining Straps Hard Suction Hose Storage, One (1) Hose, Above Officer's Side High Cmpt, 'V' Trough (Painted), Retaining Straps Hard Suction Hose Storage, One (1) Hose, Above Officer's Side Low Cmpt, 'V' Trough (Painted), Retaining Straps Hard Suction Hose Storage, One (1) Hose, Enclosed in Ladder Compartment Hard Suction Hose Storage, One (1) Hose, Behind Driver's Side Header, Enclosed Compartment, Painted Door Hard Suction Hose Storage, One (1) Hose, Behind Officer's Side Header, Enclosed Compartment, Painted Door Hard Suction Hose Storage, One (1) Hose, Beneath Driver's Side 'T' Tank, Enclosed Compartment, Painted Door Hard Suction Hose Storage, One (1) Hose, Beneath Officer's Side 'T' Tank, Enclosed Compartment, Painted Door Hard Suction Hose Storage, One (1) Hose, Driver's Side of Water Tank, Enclosed Compartment, Painted Door Hard Suction Hose Storage, One (1) Hose, Officer's Side of Water Tank, Enclosed Compartment, Painted Door Hard Suction Hose Storage, One (1) Hose, Behind Driver's Side Header, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, One (1) Hose, Behind Officer's Side Header, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, One (1) Hose, Beneath Driver's Side 'T' Tank, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, One (1) Hose, Beneath Officer's Side 'T' Tank, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, One (1) Hose, Driver's Side of Water Tank, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, One (1) Hose, Officer's Side of Water Tank, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, One (1) Hose, Above Driver's Side High Cmpt, Tread Plate Box, Retaining Straps Hard Suction Hose Storage, One (1) Hose, Above Officer's Side High Cmpt, Tread Plate Box, Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Above Driver's Side High Cmpt, 'V' Trough Rack (Abraded), Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Above Officer's Side High Cmpt, 'V' Trough Rack (Abraded), Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Above Driver's Side High Cmpt, 'V' Trough Rack (Painted), Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Above Officer's Side High Cmpt, 'V' Trough Rack (Painted), Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Above Driver's Side Low Cmpt, 'V' Trough Rack (Abraded), Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Above Officer's Side Low Cmpt, 'V' Trough Rack (Abraded), Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Above Driver's Side Low Cmpt, 'V' Trough Rack (Painted), Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Above Officer's Side Low Cmpt, 'V' Trough Rack (Painted), Retaining Straps Hydraulic Equipment Rack Attachment, Driver's Side, Hard Suction Hose Storage (2 Hoses), Tread Plate Box, Retaining Straps Hydraulic Equipment Rack Attachment, Officer's Side, Hard Suction Hose Storage (2 Hoses), Tread Plate Box, Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Behind Driver's Side Header, Enclosed Compartment, Painted Door

009403 009404 009405 009406 009407 009408 009409 009410 009411 009412 009413 009414 009415 009416 009417 009418 009419 009420 009421 009422 009423 009424 009425 009426 009427 009428 009429 009430 009431 009432 009433 009434 009435 009436 009437 009438 009439 009440 009307 009308 009309 009310 009311 009312 009313 009314 009315 009316 009317 009318 009319 009320 009321 009322 009323 009324 009325 009326 009327 009328 009329 009330 009331 009332 009334 009335 009336 009338 009339 009340 009342 009343 009344 009345 009346 009348 009349 009350 009351 009352 009358 009359 009360 009387 009388 009389 009390 009391 009392 009393 009394 009395 009396 009397 009398 009399 009400 009401 009402 Hard Suction Hose Storage, Two (2) Hoses, Behind Officer's Side Header, Enclosed Compartment, Painted Door Hard Suction Hose Storage, Two (2) Hoses, Driver's Side of Water Tank, Enclosed Compartment, Painted Door Hard Suction Hose Storage, Two (2) Hoses, Officer's Side of Water Tank, Enclosed Compartment, Painted Door Hard Suction Hose Storage, Two (2) Hoses, Behind Driver's Side Header, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, Two (2) Hoses, Behind Officer's Side Header, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, Two (2) Hoses, Driver's Side of Water Tank, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, Two (2) Hoses, Officer's Side of Water Tank, Enclosed Compartment, Tread Plate Door Hard Suction Hose Storage, Two (2) Hoses, Enclosed in Ladder Compartment Hard Suction Hose Storage, Two (2) Hoses, Above Driver's Side High Cmpt, Tread Plate Box, Retaining Straps Hard Suction Hose Storage, Two (2) Hoses, Above Officer's Side High Cmpt, Tread Plate Box, Retaining Straps Hard Suction Hose Storage, Three (3) Hoses, Above Driver's Side Low Cmpt, 'V' Trough Rack (Abraded), Retaining Straps Hard Suction Hose Storage, Three (3) Hoses, Above Officer's Side Low Cmpt, 'V' Trough Rack (Abraded), Retaining Straps Hard Suction Hose Storage, Three (3) Hoses, Above Driver's Side Low Cmpt, 'V' Trough Rack (Painted), Retaining Straps Hard Suction Hose Storage, Three (3) Hoses, Above Officer's Side Low Cmpt, 'V' Trough Rack (Painted), Retaining Straps Hose Bed, Forward of Turntable, Painted Primary Body Color Finish, (1) Chute, Tread Plate Door (75') Hose Bed, Forward of Turntable, Painted Primary Body Color Finish, (1) Chute, Painted Door (75') Hose Bed, Forward of Turntable, Painted Primary Body Color Finish, (2) Chutes, Tread Plate Doors (100' RMP/125') Hose Bed, Forward of Turntable, Painted Primary Body Color Finish, (2) Chutes, Painted Doors (100' RMP/125') Hose Bed, Forward of Turntable, Painted Primary Body Color Finish, (2) Chutes, Tread Plate Doors (85' RMP/105') Hose Bed, Forward of Turntable, Painted Primary Body Color Finish, (2) Chutes, Painted Doors (85' RMP/105') Hose Bed, Single, Behind Officer's Side Cmpts, Painted Primary Body Color Finish, (1) Chute, Tread Plate Door Hose Bed, Single, Behind Officer's Side Cmpts, Painted Primary Body Color Finish, (1) Chute, Painted Door Hose Bed, Single, Behind Driver's Side Cmpts, Painted Primary Body Color Finish, (1) Chute, Tread Plate Door Hose Bed, Single, Behind Driver's Side Cmpts, Painted Primary Body Color Finish, (1) Chute, Painted Door Hose Bed, Split, Behind Cmpts, Painted Primary Body Color Finish, (2) Chutes, Tread Plate Doors Hose Bed, Split, Behind Cmpts, Painted Primary Body Color Finish, (2) Chutes, Painted Doors Hose Bed Doors, Tread Plate, Power Operated, Sequenced, Grote LED Lighting Hose Bed Doors, Tread Plate, Power Operated, Sequenced, Whelen LED Lighting Hose Bed Doors, Tread Plate, Power Operated, Sequenced, On-Scene Night Axe LED Lighting Hose Bed Doors, Tread Plate, Power Operated, Independent, Grote LED Lighting Hose Bed Doors, Tread Plate, Power Operated, Independent, Whelen LED Lighting Hose Bed Doors, Tread Plate, Power Operated, Independent, On-Scene Night Axe LED Lighting Hose Bed Dividers, (2), 1/4" Alum., Adjustable, Abraded Hose Bed Dividers, (3), 1/4" Alum., Adjustable, Abraded Hose Bed Dividers, (4), 1/4" Alum., Adjustable, Abraded Hose Bed Dividers, (5), 1/4" Alum., Adjustable, Abraded Hose Bed Dividers, (6), 1/4" Alum., Adjustable, Abraded Hose Bed Dividers, (2), 1/4" Alum., Adjustable, Line-X, Black Hose Bed Dividers, (3), 1/4" Alum., Adjustable, Line-X, Black Hose Bed Dividers, (4), 1/4" Alum., Adjustable, Line-X, Black Hose Bed Dividers, (5), 1/4" Alum., Adjustable, Line-X, Black Hose Bed Dividers, (6), 1/4" Alum., Adjustable, Line-X, Black Hose Bed Dividers, EHL, (2), 3/16" Alum., Adjustable, Line-X, Black Hose Bed Dividers, (2), 3/16" Alum., Line-X, Black (55') Hose Bed Dividers, (2), 3/16" Alum., Line-X, Black (All Except 55') WL1, Air Bottle Compartment, OEM Polished SS Door, Single 8" WL1, Air Bottle Compartment, OEM Polished SS Door, Double (Vertical) 8" WL1, Air Bottle Compartment, OEM Polished SS Door, Triple (Vertical) 8" WL1, Air Bottle Compartment, OEM Polished SS Door, Triple (Triangle) 8" WL1, Extinguisher/Water Can Compartment, OEM Polished SS Door, Single (Up to 9" Diameter) WL1, Speedy Dry Compartment, OEM Polished SS Door, Triangle WL1, Wheel Chock Compartment, OEM Polished SS Door WL1, Air Bottle Compartment, OEM Painted SS Door, Single 8" WL1, Air Bottle Compartment, OEM Painted SS Door, Double (Vertical) 8" WL1, Air Bottle Compartment, OEM Painted SS Door, Triple (Vertical) 8" WL1, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" WL1, Extinguisher/Water Can Compartment, OEM Painted SS Door, Single (Up to 9" Diameter) WL1, Speedy Dry Compartment, OEM Painted SS Door, Triangle WL1, Wheel Chock Compartment, OEM Painted SS Door WL2, Air Bottle Compartment, OEM Polished SS Door, Single 8" WL2, Air Bottle Compartments, OEM Polished SS Doors, (2) Back-to-Back Single 8" WL2, Extinguisher/Water Can Compartment, OEM Polished SS Door, Single (Up to 9" Diameter) WL2, Air Bottle Compartment, OEM Painted SS Door, Single 8" WL2, Air Bottle Compartments, OEM Painted SS Doors, Two (2) Back-to-Back Single 8" WL2, Extinguisher/Water Can Compartment, OEM Painted SS Door, Single (Up to 9" Diameter) WL2, Drawer, One (1), Above Tandem Wheels WL2, Drawers, Two (2), Above Tandem Wheels WL3, Air Bottle Compartment, OEM Polished SS Door, Single 8" WL3, Air Bottle Compartment, OEM Polished SS Door, Double (Vertical) 8" WL3, Air Bottle Compartment, OEM Polished SS Door, Triple (Vertical) 8" WL3, Air Bottle Compartment, OEM Polished SS Door, Triple (Triangle) 8" WL3, Air Bottle Compartment with Fuel Fill, OEM Polished SS Door, Double 8" WL3, Extinguisher/Water Can Compartment, OEM Polished SS Door, Single (Up to 9" Diameter) WL3, Speedy Dry Compartment, OEM Polished SS Door, Triangle WL3, Wheel Chock Compartment, OEM Polished SS Door WL3, Air Bottle Compartment, OEM Painted SS Door, Single 8" WL3, Air Bottle Compartment, OEM Painted SS Door, Double (Vertical) 8" WL3, Air Bottle Compartment, OEM Painted SS Door, Triple (Vertical) 8" WL3, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" WL3, Air Bottle Compartment with Fuel Fill, OEM Painted SS Door, Double 8" WL3, Extinguisher/Water Can Compartment, OEM Painted SS Door, Single (Up to 9" Diameter) WL3, Speedy Dry Compartment, OEM Painted SS Door, Triangle WL3, Wheel Chock Compartment, OEM Painted SS Door WL3, Air Bottle Comparments, Painted SS Doors, Two (2) Stacked Single 8", Rage WR1, Air Bottle Compartment, OEM Polished SS Door, Single 8" WR1, Air Bottle Compartment, OEM Polished SS Door, Double (Vertical) 8" WR1, Air Bottle Compartment, OEM Polished SS Door, Triple (Vertical) 8" WR1, Air Bottle Compartment, OEM Polished SS Door, Triple (Triangle) 8" WR1, Extinguisher/Water Can Compartment, OEM Polished SS Door, Single (Up to 9" Diameter) WR1, Speedy Dry Compartment, OEM Polished SS Door, Triangle WR1, Wheel Chock Compartment, OEM Polished SS Door WR1, Air Bottle Compartment, OEM Painted SS Door, Single 8" WR1, Air Bottle Compartment, OEM Painted SS Door, Double (Vertical) 8" WR1, Air Bottle Compartment, OEM Painted SS Door, Triple (Vertical) 8" WR1, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" WR1, Extinguisher/Water Can Compartment, OEM Painted SS Door, Single (Up to 9" Diameter) WR1, Speedy Dry Compartment, OEM Painted SS Door, Triangle WR1, Wheel Chock Compartment, OEM Painted SS Door WR2, Air Bottle Compartment, OEM Polished SS Door, Single 8"

009848 009851 009852 009853 009854 009855 009856 009857 009858 009859 009860 009861 009862 009863 009864 009865 009866 009867 009868 009869 009870 009871 009872 009889 009890 009891 009892 009893 009894 009895 009897 009898 009899 009900 009901 009902 009903 009904 009441 009442 009443 009444 009445 009446 009447 009448 009449 009450 009451 009452 009453 009454 009455 009456 009457 009458 009459 009460 009461 009462 009463 009464 009465 009466 009501 009503 009505 009507 009509 009511 009513 009515 009517 009522 009523 009524 009525 009526 009529 009530 009531 009532 009536 009607 009705 009706 009817 009818 009837 009838 009839 009840 009841 009842 009843 009844 009845 009846 009847 WR2, Air Bottle Compartments, OEM Polished SS Doors, Two (2) Back-to-Back Single 8" WR2, Extinguisher/Water Can Compartment, OEM Polished SS Door, Single (Up to 9" Diameter) WR2, Air Bottle Compartment, OEM Painted SS Door, Single 8" WR2, Air Bottle Compartments, OEM Painted SS Doors, Two (2) Back-to-Back Single 8" WR2, Extinguisher/Water Can Compartment, OEM Painted SS Door, Single (Up to 9" Diameter) WR2, Drawer, One (1), Above Tandem Wheels WR2, Drawers, Two (2), Above Tandem Wheels WR3, Air Bottle Compartment, OEM Polished SS Door, Single 8" WR3, Air Bottle Compartment, OEM Polished SS Door, Double (Vertical) 8" WR3, Air Bottle Compartment, OEM Polished SS Door, Triple (Vertical) 8" WR3, Air Bottle Compartment, OEM Polished SS Door, Triple (Triangle) 8" WR3, Air Bottle Compartment with Fuel Fill, OEM Polished SS Door, Double 8" WR3, Extinguisher/Water Can Compartment, OEM Polished SS Door, Single (Up to 9" Diameter) WR3, Speed Dry Compartment, OEM Polished SS Door, Triangle WR3, Wheel Chock Compartment, OEM Polished SS Door WR3, Air Bottle Compartment, OEM Painted SS Door, Single 8" WR3, Air Bottle Compartment, OEM Painted SS Door, Double (Vertical) 8" WR3, Air Bottle Compartment, OEM Painted SS Door, Triple (Vertical) 8" WR3, Air Bottle Compartment, OEM Painted SS Door, Triple (Triangle) 8" WR3, Air Bottle Compartment with Fuel Fill, OEM Painted SS Door, Double 8" WR3, Extinguisher/Water Can Compartment, OEM Painted SS Door, Single (Up to 9" Diameter) WR3, Speed Dry Compartment, OEM Painted SS Door, Triangle WR3, Wheel Chock Compartment, OEM Painted SS Door WR3, Air Bottle Compartments, OEM Painted SS Doors, Two (2) Stacked Single 8", Rage Fuel Fills, Fire Shopp Brushed Doors, Driver's and Officer's Side Fuel Fills, Fire Shopp Painted Doors, Driver's and Officer's Side Pump, Darley, Single-Stage, 1000 GPM, LDM, MagnaTrans Transmission Pump, Darley, Single-Stage, 1250 GPM, LDM, MagnaTrans Transmission Pump, Darley, Single-Stage, 1500 GPM, LDM, MagnaTrans Transmission Pump, Darley, Single-Stage, 1750 GPM, LDM, MagnaTrans Transmission Pump, Darley, Two-Stage, 1000 GPM, EM, MagnaTrans Transmission Pump, Darley, Two-Stage, 1250 GPM, EM, MagnaTrans Transmission Pump, Darley, Two-Stage, 1500 GPM, EM, MagnaTrans Transmission Pump, Darley, Two-Stage, 1750 GPM, EM, MagnaTrans Transmission Pump, Darley, Two-Stage, 2000 GPM, EM, MagnaTrans Transmission Manifold, Darley Primer, Darley, Fluidless, Electric 12V Prime Overheat Protection System, Darley, With Lights Transfer Valve, Darley, Air-Operated Mechanical Seals, Darley Governor, TGA300, FRC Governor, TGA400, FRC Governor, Pump Boss 400, FRC Butterfly Valve, Side Steamer, 6" Manual, Darley Scene Light, (1), 12V, Whelen, Surface Mount, LED 600 Series Gradient Opti-Scene Compressor, 120V, Gast OEM Chassis Preparations, S450 OEM Chassis Preparations, S600 Rear Compartment Door, (1), Tread Plate Lap Door, Grab Handle Rear Compartment Door, (1), Painted Lap Door, Grab Handle Crosslay Divider, (1), Abraded Aluminum Crosslay Divider, (1), Abraded Aluminum, Notched Crosslay Divider, (1), Black Line-X Aluminum Crosslay Divider, (1), Black Line-X Aluminum, Notched Crosslay Dividers, (2), Abraded Aluminum Crosslay Dividers, (2), Abraded Aluminum, Notched Crosslay Dividers, (2), Black Line-X Aluminum Crosslay Dividers, (2), Black Line-X Aluminum, Notched Crosslay Dividers, (3), Abraded Aluminum Crosslay Dividers, (3), Abraded Aluminum, Notched Crosslay Dividers, (3), Black Line-X Aluminum Crosslay Dividers, (3), Black Line-X Aluminum, Notched Crosslay Divider, (1), Abraded Aluminum, Center Vertical, Rage Pump Compartment Heater, (1) 28,000 BTU, Switch on Pump Panel Pump Compartment Heater, (1) 28,000 BTU, Switch in Cab Pump Compartment Heater, (1) 28,000 BTU, Thermostat Pump Compartment Heater, (1) 40,000 BTU, Switch on Pump Panel Pump Compartment Heater, (1) 40,000 BTU, Switch in Cab Pump Compartment Heater, (1) 40,000 BTU, Thermostat Pump Compartment Heaters, (2) 28,000 BTU, Coolant Boost Pump, Switch on Pump Panel Pump Compartment Heaters, (2) 28,000 BTU, Coolant Boost Pump, Switch in Cab Pump Compartment Heaters, (2) 28,000 BTU, Coolant Boost Pump, Thermostat Pull Out Platform, (1), Driver's Side Pump Module, Innovative Industries Pull Out Platform, (1), Officer's Side Pump Module, Innovative Industries Pull Out Platforms, (2), Both Sides of Pump Module, Innovative Industries Running Board, Driver's Side, Bolt-On, Tread Plate Running Board, Driver's Side, Bolt-On, Tread Plate, Bar Grate Insert Running Board, Driver's Side, Bolt-On, Tread Plate, Bar Grate Insert, Notched Running Board, Driver's Side, Bolt-On, Tread Plate, Bar Grate Insert, Splash Pan Running Board, Driver's Side, Bolt-On, Tread Plate, Bar Grate Insert, Splash Pan, Notched Running Board, Driver's Side, Bolt-On, Tread Plate, Grip Strut Insert Running Board, Driver's Side, Bolt-On, Tread Plate, Grip Strut Insert, Notched Running Board, Driver's Side, Bolt-On, Tread Plate, Grip Strut Insert, Splash Pan Running Board, Driver's Side, Bolt-On, Tread Plate, Grip Strut Insert, Splash Pan, Notched Running Board, Officer's Side, Bolt-On, Tread Plate, Bar Grate Insert, Splash Pan Running Board, Driver's Side, Integral, Tread Plate Heat Deflection System, Powered by SG-09 SG-09 Auxiliary Power Unit, Segregated System, Niehoff Alternator SG-09 Auxiliary Power Unit, Integrated System, 40,000 BTU Aux. Heater, Leece-Neville Alternator SG-09 Auxiliary Power Unit, Integrated System, 40,000 BTU Aux. Heater, Niehoff Alternator SG-09 Auxiliary Power Unit, Segregated System, Leece-Neville Alternator SG-09 Auxiliary Power Unit, Integrated System, 9,000 BTU Aux. Electric Heater, Leece-Neville Alternator SG-09 Auxiliary Power Unit, Integrated System, 9,000 BTU Aux. Electric Heater, Niehoff Alternator Antenna (1), No Radio, Dealer/Customer Supplied, OEM Installed Antennas (2), No Radio, Dealer/Customer Supplied, OEM Installed Antennas (3), No Radio, Dealer/Customer Supplied, OEM Installed Antennas (4), No Radio, Dealer/Customer Supplied, OEM Installed Antenna (1), Radio (1), Dealer/Customer Supplied, OEM Installed Antennas (2), Radio (1), Dealer/Customer Supplied, OEM Installed

010025 010026 010027 010028 010029 010030 010031 010032 010033 010034 010035 010036 010037 010038 010039 010040 010041 010042 010043 010044 010045 010046 010047 010048 010049 010050 010051 010052 010053 010054 010055 010056 010057 010058 010059 010060 010061 010063 009905 009906 009907 009908 009909 009910 009911 009912 009915 009916 009918 009937 009938 009941 009942 009943 009945 009947 009948 009949 009950 009951 009952 009953 009954 009956 009957 009959 009963 009964 009965 009966 009967 009968 009969 009970 009971 009972 009973 009974 009975 009976 009977 009978 009979 009980 009981 009982 009983 009984 009985 009986 009987 009988 009989 009990 009991 009992 009993 009994 010024 Antennas (3), Radio (1), Dealer/Customer Supplied, OEM Installed Antennas (4), Radio (1), Dealer/Customer Supplied, OEM Installed Antenna (1), Radio (2), Dealer/Customer Supplied, OEM Installed Antennas (2), Radio (2), Dealer/Customer Supplied, OEM Installed Antennas (3), Radio (2), Dealer/Customer Supplied, OEM Installed Antennas (4), Radio (2), Dealer/Customer Supplied, OEM Installed Breathing Air Level and Warning System, Class 1 Dual AirMinder, Turntable and Tip Breathing Air Level and Warning System, Programmed into AL-11, Light/Buzzer at Tip Hydraulic Reel Only, Hannay, Red Enamel Finish, No Lead-Ins/Hose Provided Hydraulic Reel Only, Hannay, Stainless Steel Finish, No Lead-Ins/Hose Provided Body, 100" Wide, Walk Around Rescue, Single-Axle, Aluminum, 3/16" Water Tank Level Gauge, OMNI Pump Control System Foam Tank Level Gauge, OMNI Pump Control System Programmed Dunnage Compartment, Tread Plate, Above CORE Pump Module ,NO Cover Speedlays in Lift Out Trays, Ahead of Pump Panel, (2) 1-1/2", Side-By-Side Speedlay Rollers Speedlay Flooring, Slotted Aluminum Storage Compartment, Transverse, CORE Air Horn Activation, OMNI Pump Control System Programmed Access Panel, Pump, R1 Compartment, Side-Hinged, Line-X Aluminum, Compression Latch Pump Panel Lighting, Side Panels, LED, On-Scene Night Axe, L1 Rollup Door, CORE Sub-Frame, GS-36, Hot-Dip Galvanized (CORE) Transverse Area with Pump Access, Forward Body Compartments Electrical System, Pumper, Class 1 ES-Key Multiplex, QL-12 Harnesses, Sealed Switches Class 1 1Touch Switch Module, 4-Button Class 1 1Touch Switch Module, 8-Button Class 1 1Touch Switch Module, 12-Button Intake Relief Valve, Pump, Trident, AirMax Compartment Drop-Down Door Steps, Four (4), Painted Aluminum Compartment Drop-Down Door Steps, Six (6), Painted Aluminum Tool Compartments Below Walkway, NO Restraint, Turtle Tile Flooring Tool Compartments Below Walkway, NO Restraint, Dri-Dek Tile Flooring Tool Compartments Below Walkway, Webbing Restraint, Turtle Tile Flooring Tool Compartments Below Walkway, Webbing Restraint, Dri-Dek Tile Flooring Tool Compartments Below Walkway, Tread Plate Door and LED Light, Turtle Tile Flooring Tool Compartments Below Walkway, Tread Plate Door and LED Light, Dri-Dek Tile Flooring Walkway, Center, Top Mount, 18", LED Lighting Walkway, Center, Top Mount, 18", LED Lighting, Mansaver Bars, Yellow Dunnage Compartment, Tread Plate, Above Pump Module, NO Cover Dunnage Compartment, Tread Plate, Above Pump Module, With Cover, Tread Plate Dunnage Compartment, Tread Plate, Above Pump Module, With Cover, Tread Plate with Bar Grate Dunnage Compartment, Tread Plate, Above Pump Module, With Cover, Tread Plate with Bar Grate Cover, SG-09 Dunnage Compartment, Tread Plate, Above Pump Module, With Cover, Vinyl, Red Dunnage Compartment, Tread Plate, Above Pump Module, With Cover, Vinyl, Black Dunnage Compartment, Tread Plate, Above Front of Body, NO Cover Dunnage Compartment, Tread Plate, Above Front of Body, With Cover, Tread Plate Dunnage Compartment, Tread Plate, Above Front of Body, With Cover, Tread Plate with Bar Grate Dunnage Compartment, Tread Plate, Above Front of Body, With Cover, Vinyl, Red Dunnage Compartment, Tread Plate, Above Front of Body, With Cover, Vinyl, Black Tread Plate Dunnage, Above Pump Module Tread Plate Dunnage, Above Pump Module, Tread Plate Cover Tread Plate Dunnage, Above Pump Module, Tread Plate with Bar Grate Cover Tread Plate Dunnage, Above Pump Module, Tread Plate with Bar Grate Cover (SG-09) Tread Plate Dunnage, Above Pump Module, Vinyl Cover (Red) Tread Plate Dunnage, Above Pump Module, Vinyl Cover (Black) Tread Plate Dunnage, Above Torque Box Tread Plate Dunnage, Above Torque Box, Tread Plate Cover Tread Plate Dunnage, Above Torque Box, Tread Plate with Bar Grate Cover Tread Plate Dunnage, Above Torque Box, Vinyl Cover (Red) Tread Plate Dunnage, Above Torque Box, Vinyl Cover (Black) Locator Light (1), 12V, Tomar, Micro IV 470S Strobe, Amber, Activated by Aerial Master Locator Light (1), 12V, Tomar, Micro IV 470S Strobe, Blue, Activated by Aerial Master Locator Lights (2), 12V, Tomar, Micro IV 470S Strobe, Amber, Activated by Aerial Master Locator Lights (2), 12V, Tomar, Micro IV 470S Strobe, Blue, Activated by Aerial Master Dump Valve, Air, SS Newton 10x10, 18" Telescoping Chute, (1) Switch in Cab Dump Valve, Air, SS Newton 10x10, 18" Telescoping Chute, (1) Switch Each in Cab and at Pump Panel Dump Valve, Air, SS Newton 10x10, 18" Telescoping Chute, (1) Switch Each in Cab and at Rear Body Dump Valve, Air, SS Newton 10x10, 18" Telescoping Chute, (2) Switches in Cab Dump Valve, Air, SS Newton 10x10, 18" Telescoping Chute, (2) Switches Each in Cab and at Pump Panel Dump Valve, Air, SS Newton 10x10, 18" Telescoping Chute, (2) Switches Each in Cab and at Rear Body Dump Valve, Air, SS Newton 10x10, Dump Valve, Manual Swivel and 36" Extension Chute, (1) Switch in Cab Dump Valve, Air, SS Newton 10x10, Dump Valve, Manual Swivel and 36" Extension Chute, (1) Switch Each in Cab and at Pump Panel Dump Valve, Air, SS Newton 10x10, Dump Valve, Manual Swivel and 36" Extension Chute, (1) Switch Each in Cab and at Rear Body Dump Valve, Electric, SS Newton 10x10, 18" Telescoping Chute, (2) Switches in Cab Dump Valve, Electric, SS Newton 10x10, 18" Telescoping Chute, (2) Switches Each in Cab and at Pump Panel Dump Valve, Electric, SS Newton 10x10, 18" Telescoping Chute, (2) Switches Each in Cab and at Rear Body Dump Valve, Electric, SS Newton 10x10, Dump Valve, Manual Swivel and 36" Extension Chute, (1) Switch in Cab Dump Valve, Electric, SS Newton 10x10, Dump Valve, Manual Swivel and 36" Extension Chute, (1) Switch Each in Cab and at Pump Panel Dump Valve, Electric, SS Newton 10x10, Dump Valve, Manual Swivel and 36" Extension Chute, (1) Switch Each in Cab and at Rear Body Dump Valve, Manual, Black Steel Newton 10x10, 36" Telescoping Chute Dump Valve, Manual, Black Steel Newton 10x10, 90 Degree Elbow and 48" Extension Chute Dump Valve, Manual, Body Color (Primary) Steel Newton 10x10, 36" Telescoping Chute Dump Valve, Manual, Body Color (Primary) Steel Newton 10x10, 90 Degree Elbow and 48" Extension Chute Dump Valve, Manual, SS Newton 10x10, 36" Telescoping Chute Dump Valve, Manual, SS Newton 10x10, 90 Degree Elbow and 48" Extension Chute Dump Valve, Manual, SS Newton 10x10, Dump Valve, Manual Swivel and 36" Telescoping Chute Direct Tank Fill, 2-1/2", Driver's Side Rear, Akron 8825 Valve, TSC Handle, FNST Swivel Direct Tank Fill, 2-1/2", Driver's Side Rear, Elkhart EB25 Valve, D2 Handle, FNST Swivel Direct Tank Fill, 2-1/2", Officer's Side Rear, Akron 8825 Valve, TSC Handle, FNST Swivel Direct Tank Fill, 2-1/2", Officer's Side Rear, Elkhart EB25 Valve, D2 Handle, FNST Swivel Direct Tank Fill, 2-1/2", Officer's Side, Akron 8825 Valve, TSC Handle, FNST Swivel Direct Tank Fill, 2-1/2", Officer's Side, Elkhart EB25 Valve, D2 Handle, FNST Swivel Direct Tank Fill, 4", Driver's Side Rear, Akron 7940 Valve, Handwheel Control, MNST Thread Direct Tank Fill, 4", Driver's Side Rear, Elkhart EB4B Valve, Handwheel Control, MNST Thread Direct Tank Fill, 4", Officer's Side Rear, Akron 7940 Valve, Handwheel Control, MNST Thread Direct Tank Fill, 4", Officer's Side Rear, Elkhart EB4B Valve, Handwheel Control, MNST Thread Direct Tank Fill Fittings, Plug with Chain, 2-1/2" NST, South Park, Chrome Direct Tank Fill Fittings, Plug with Chain, 2-1/2" NST, Trident, Chrome Direct Tank Fill Fittings, Elbow (30 Deg) 4" FNST x 4" MNST, NST Cap, South Park, Chrome

010183 010184 010185 010186 010187 010188 010189 010190 010191 010192 010193 010194 010195 010196 010197 010198 010199 010200 010201 010202 010203 010204 010205 010206 010207 010208 010209 010210 010211 010212 010213 010214 010215 010216 010217 010218 010219 010220 010064 010068 010069 010070 010071 010072 010073 010074 010075 010076 010077 010078 010080 010081 010082 010083 010084 010085 010086 010087 010088 010089 010092 010093 010106 010108 010109 010110 010111 010112 010113 010114 010115 010132 010150 010152 010153 010156 010158 010159 010160 010161 010164 010165 010166 010167 010168 010169 010170 010171 010172 010173 010174 010175 010176 010177 010178 010179 010180 010181 010182 Direct Tank Fill Fittings, Elbow (30 Deg) 4" FNST x 4" MNST, NST Cap, Trident, Chrome Water Tank Level Gauge, Class 1 Intelli-Tank, Pump Operator's Panel, Slave in Cab Water Tank Level Gauge, Class 1 Intelli-Tank, Pump Operator's Panel, Rear Body, Slave in Cab Water Tank Level Gauge, Class 1 ITL-40M, Pump Operator's Panel Water Tank Level Gauge, Class 1 ITL-40M, Pump Operator's Panel, Slave in Cab Water Tank Level Gauge, FRC Tankvision, Pump Operator's Panel, Slave in Cab Water Tank Level Gauge, FRC Tankvision, Pump Operator's Panel, Officer's Side Pump Panel, Slave in Cab Water Tank Level Gauge, FRC Tankvision, Pump Operator's Panel, Rear Body, Slave in Cab Water Tank Level Gauge, Innovative Controls SL Plus, Pump Operator's Panel Water Tank Level Gauge, Innovative Controls SL Plus, Pump Operator's Panel, Slave in Cab Water Tank Level Gauge, Innovative Controls SL Plus, Pump Operator's Panel, Officer's Side Pump Panel Water Tank Level Gauge, Innovative Controls SL Plus, Pump Operator's Panel, Officer's Side Pump Panel, Slave in Cab Tow Option, Rear, Tow Eye, One (1), Underbody Subframe Tow Option, Rear, Tow Eyes, Two (2), Underbody Subframe Water Tank Level Display, Innovative Controls SL Plus Monster Strip Light, Cab Sides, IC Driver Water Tank Level Display, Innovative Controls SL Plus Monster Strip Light, Cab Sides, FRC Driver Water Tank Level Display, Innovative Controls SL Plus Monster Strip Light, Cab Sides, Rear of Body, IC Driver Water Tank Level Display, Innovative Controls SL Plus Monster Strip Light, Cab Sides, Rear of Body, FRC Driver Foam Tank Level Gauge, Class 1 ITL-40M Gauge, Class A Foam Foam Tank Level Gauge, Class 1 ITL-40M Gauge, Class B Foam Foam Tank Level Gauge, Innovative Controls SL Plus, Class A Foam Foam Tank Level Gauge, Innovative Controls SL Plus, Class B Foam Water Tank Level Gauge, Innovative Controls SL Plus, Pump Operator's Panel, Rear Body Water Tank Level Gauge, Innovative Controls SL Plus, Pump Operator's Panel, Rear Body, Slave in Cab Running Board, Driver's Side, Bolt-On, Grip Strut Running Board, Officer's Side, Bolt-On, Tread Plate Running Board, Officer's Side, Bolt-On, Tread Plate, Bar Grate Insert Running Board, Officer's Side, Bolt-On, Tread Plate, Bar Grate Insert, Notched Running Board, Officer's Side, Bolt-On, Tread Plate, Bar Grate Insert, Splash Pan, Notched Running Board, Officer's Side, Bolt-On, Tread Plate, Grip Strut Insert Running Board, Officer's Side, Bolt-On, Tread Plate, Grip Strut Insert, Notched Running Board, Officer's Side, Bolt-On, Tread Plate, Grip Strut Insert, Splash Pan Running Board, Officer's Side, Bolt-On, Tread Plate, Grip Strut Insert, Splash Pan, Notched Running Board, Officer's Side, Integral, Tread Plate Running Board, Officer's Side, Bolt-On, Grip Strut Water Tank Level Display, Innovative Controls SL Plus Monster Strip Light, Cab Sides, Class 1 Driver Water Tank Level Display, Innovative Controls SL Plus Monster Strip Light, Cab Sides, Rear of Body, Class 1 Driver Hose Bed Divider, (1), 1/4" Alum., Adjustable, Abraded Hose Bed Divider, (1), 1/4" Alum., Adjustable, Line-X, Black EHL Divider, (1), 3/16" Alum., Adjustable, Line-X, Black Hose Bed Divider, (1), 3/16" Alum., Line-X, Black (55') Hose Bed Divider, (1), 3/16" Alum., Line-X, Black (All Except 55') Stabilizers, Rear "H" Style, 13' 6" Spread, Standard Stroke, NO Stabilizer Pins (55') Stabilizers, Rear "H" Style, 13' 6" Spread, Standard Stroke, WITH Stabilizer Pins (55') Stabilizers, Rear "H" Style, 13' 6" Spread, Additional Penetration Stroke, NO Stabilizer Pins (55') Stabilizers, Rear "H" Style, 13' 6" Spread, Additional Penetration Stroke, WITH Stabilizer Pins (55') Stabilizers, Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (75' Single Axle) Stabilizers, Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (75' Single Axle) Stabilizers, Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (75' Single Axle) Stabilizers, Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (75' Single Axle) Stabilizers, Front Down and Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (75' Single Axle) Stabilizers, Front Down and Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (75' Single Axle) Stabilizers, Front Down and Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (75' Single Axle) Stabilizers, Front Down and Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (75' Single Axle) Stabilizers, Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (75' Tandem Axle) Stabilizers, Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (75' Tandem Axle) Stabilizers, Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (75' Tandem Axle) Stabilizers, Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (75' Tandem Axle) Stabilizers, Front Down and Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (75' Tandem Axle) Stabilizers, Front Down and Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (75' Tandem Axle) Stabilizers, Front Down and Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (75' Tandem Axle) Stabilizers, Front Down and Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (75' Tandem Axle) Rear Compartment Door, (1), Tread Plate Lap Door, Non-Locking D-Ring Latch Rear Compartment Door, (1), Painted Lap Door, Non-Locking D-Ring Latch Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (85' MMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (85' MMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (85' MMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (85' MMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (85' RMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (85' RMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (85' RMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (85' RMP) Stabilizers, Front "H" Style and Rear Down, 18' Spread, Standard Stroke, NO Stabilizer Pins (100' MMA) Stabilizers, Front "H" Style and Rear Down, 18' Spread, Standard Stroke, WITH Stabilizer Pins (100' MMA) Stabilizers, Front "H" Style and Rear Down, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (100' MMA) Stabilizers, Front "H" Style and Rear Down, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (100' MMA) Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (100' MMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (100' MMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (100' MMP) Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (100' MMP) Stabilizers, Front Down and Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (UT 100') Stabilizers, Front Down and Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (UT 100') Stabilizers, Front Down and Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (UT 100') Stabilizers, Front Down and Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (UT 100') Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (105') Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (105') Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (105') Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (105') Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, NO Stabilizer Pins (100' RMP/125') Stabilizers, Front and Rear "H" Style, 18' Spread, Standard Stroke, WITH Stabilizer Pins (100' RMP/125') Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, NO Stabilizer Pins (/100' RMP/125') Stabilizers, Front and Rear "H" Style, 18' Spread, Additional Penetration Stroke, WITH Stabilizer Pins (100' RMP/125') Fuel Fill, OEM Polished Door, Driver's Side Fuel Fill, OEM Polished Door, Officer's Side Fuel Fill, OEM Painted Door, Driver's Side Fuel Fill, OEM Painted Door, Officer's Side Fuel Fills, OEM Stainless Steel Polished Doors, Driver's and Officer's Side Fuel Fills, OEM Stainless Steel Painted Doors, Driver's and Officer's Side Power and Ground Lead, 12V Drop, Battery Direct, 14 Gauge Wire

100069 100070 100071 100072 100073 100074 100075 100076 100077 100078 100079 100081 100082 100083 100084 100085 100086 100087 100088 100089 100090 100091 100092 100093 100094 100095 100096 100097 100098 100099 100100 100101 100102 100103 100104 100105 100106 100107 010221 010222 010226 100001 100002 100003 100004 100005 100006 100011 100012 100013 100014 100015 100016 100017 100018 100023 100024 100025 100026 100027 100028 100029 100030 100031 100032 100033 100034 100035 100036 100037 100038 100039 100040 100041 100042 100043 100044 100045 100046 100047 100048 100049 100050 100051 100052 100053 100054 100055 100056 100057 100060 100061 100062 100063 100064 100065 100066 100067 100068 Power and Ground Lead, 12V Drop, Battery Direct, 10 Gauge Wire, 6-Position Distribution Panel Power and Ground Lead, 12V Drop, Battery Direct, 8 Gauge Wire, 12-Position Distribution Panel Accessory (Cigarette Lighter) Outlet, 12V, Battery Direct Hose Bed Rear Restraint, Webbing, 2" Hose Bed Rear Restraint, Vinyl, Top C-Rail, Bottom Bungee, Black Hose Bed Rear Restraint, Vinyl, Top C-Rail, Bottom Bungee, Red Hose Bed Rear Restraint, Vinyl, Top C-Rail, Bottom Footman Loop / J-Hook, Black Hose Bed Rear Restraint, Vinyl, Top C-Rail, Bottom Footman Loop / J-Hook, Red Storage Box (1), Nozzle/Tips, At Ladder Tip Radio Interface Cable, David Clark, Kenwood Radio Interface Cable, David Clark, Motorola Radio Interface Cable, David Clark, Uniden Radio Interface Cable, David Clark, Vertex Radio Interface Cable, Firecom, Kenwood Radio Interface Cable, Firecom, Motorola Radio Interface Cable, Firecom, Uniden Radio Interface Cable, Firecom, Vertex Radio Interface Cable, Sigtronics, Kenwood Radio Interface Cable, Sigtronics, Motorola Radio Interface Cable, Sigtronics, Uniden Radio Interface Cable, Sigtronics, Vertex Intercom System, Firecom 5100D, 4 Cab Position, Wired Driver/Officer (UH-51), 2 Wired Crew (UH-52) Intercom System, Firecom 5100D, 4 Cab Position, Wireless Driver (UHW-51), Wired Officer (UH-51), 2 Wired Crew (UH-52) Intercom System, Firecom 5100D, 4 Cab Position, Wireless Driver/Officer (UHW-51), 2 Wired Crew (UH-52) Intercom System, Firecom 5100D, 4 Cab Position, Wireless Driver/Officer (UHW-51), 2 Wireless Crew (UHW-52) Intercom System, Firecom 5100D, 5 Cab Position, Wired Driver/Officer (UH-51), 3 Wired Crew (UH-52) Intercom System, Firecom 5100D, 5 Cab Position, Wireless Driver (UHW-51), Wired Officer (UH-51), 3 Wired Crew (UH-52) Intercom System, Firecom 5100D, 5 Cab Position, Wireless Driver/Officer (UHW-51), 3 Wired Crew (UH-52) Intercom System, Firecom 5100D, 5 Cab Position, Wireless Driver/Officer (UHW-51), 3 Wireless Crew (UHW-52) Intercom System, Firecom 5100D, 6 Cab Position, Wired Driver/Officer (UH-51), 4 Wired Crew (UH-52) Intercom System, Firecom 5100D, 6 Cab Position, Wireless Driver (UHW-51), Wired Officer (UH-51), 4 Wired Crew (UH-52) Intercom System, Firecom 5100D, 6 Cab Position, Wireless Driver/Officer (UHW-51), 2 Wireless Crew (UHW-52) / 2 Wired Crew (UH-52) Intercom System, Firecom 5100D, 6 Cab Position, Wireless Driver/Officer (UHW-51), 4 Wired Crew (UH-52) Intercom System, Firecom 5100D, 6 Cab Position, Wireless Driver/Officer (UHW-51), 4 Wireless Crew (UHW-52) Intercom System, Sigtronics US45S, 4 Cab Position, Wired Driver/Officer (SE-8), 2 Wired Crew (SE-2) Intercom System, Sigtronics US67S, 5 Cab Position, Wired Driver/Officer (SE-8), 3 Wired Crew (SE-2) Intercom System, Sigtronics US67S, 6 Cab Position, Wired Driver/Officer (SE-8), 4 Wired Crew (SE-2) Intercom System, David Clark 3800, 4 Cab Position, Wired Driver/Officer (H3442), 2 Wired Crew (H3442) Intercom System, David Clark 3800, 4 Cab Position, Wireless Driver (H9940), Wired Officer (H3442), 2 Wired Crew (H3442) Intercom System, David Clark 3800, 4 Cab Position, Wireless Driver/Officer (H9940), 2 Wired Crew (H3442) Intercom System, David Clark 3800, 4 Cab Position, Wireless Driver/Officer (H9940), 2 Wireless Crew (H9940) Intercom System, David Clark 3800, 5 Cab Position, Wired Driver/Officer (H3442), 3 Wired Crew (H3442) Intercom System, David Clark 3800, 5 Cab Position, Wireless Driver (H9940), Wired Officer (H3442), 3 Wired Crew (H3442) Intercom System, David Clark 3800, 5 Cab Position, Wireless Driver/Officer (H9940), 3 Wired Crew (H3442) Intercom System, David Clark 3800, 5 Cab Position, Wireless Driver/Officer (H9940), 3 Wireless Crew (H9940) Intercom System, David Clark 3800, 6 Cab Position, Wired Driver/Officer (H3442), 4 Wired Crew (H3442) Intercom System, David Clark 3800, 6 Cab Position, Wireless Driver (H9940), Wired Officer (H3442), 4 Wired Crew (H3442) Intercom System, David Clark 3800, 6 Cab Position, Wireless Driver/Officer (H9940), 2 Wireless Crew (H9940) / 2 Wired Crew (H3442) Intercom System, David Clark 3800, 6 Cab Position, Wireless Driver/Officer (H9940), 4 Wired Crew (H3442) Intercom System, David Clark 3800, 6 Cab Position, Wireless Driver/Officer (H9940), 4 Wireless Crew (H9940) Additional Intercom Position, (1) Pump Panel, Firecom 5100D Additional Intercom Position, (1) Rear Body, Driver's Side, Firecom 5100D Additional Intercom Position, (1) Pump Panel, Sigtronics US67S Additional Intercom Position, (1) Rear Body, Driver's Side, Sigtronics US67S Additional Intercom Position, (1) Pump Panel, David Clark 3800 Additional Intercom Position, (1) Rear Body, Driver's Side, David Clark 3800 Light Tower, 240V, Command Light, CL Series, LED, 120,000 Lumen, (6) FRC Spectra Lightheads Light Tower, 240V, Command Light, CL Series, Quartz Halogen, 6000W, (6) Hubbell Lightheads Light Tower, 240V, Command Light, CL Series, Quartz Halogen, 9000W, (6) Hubbell Lightheads Light Tower, 12V, Command Light, Knight Series, LED, 60,000 Lumens, (4) FRC Evolution Lightheads Light Tower, 12V, Command Light, Knight Series, LED, 64,000 Lumens, (4) Whelen PFP2 Lightheads Light Tower, 240V, Command Light, Knight Series, LED, 120,000 Lumens, (6) FRC Spectra Lightheads Light Tower, 240V, Command Light, Knight Series, Quartz Halogen, 3000W, (4) Lumenform Lightheads Light Tower, 240V, Command Light, Knight Series, Quartz Halogen, 3900W, (6) FRC Optimum Lightheads Light Tower, 240V, Command Light, Shadow Series, LED, 80,000 Lumens, (4) FRC Spectra Lightheads Light Tower, 240V, Command Light, Shadow Series, Quartz Halogen, 2000W, (4) Lumenform Lightheads Light Tower, 240V, Will-Burt, Night Scan Chief 2.3, Quartz Halogen, 6000W, (4) FRC Optimum Lightheads Light Tower, 240V, Will-Burt, Night Scan Powerlite 3.0, Quartz Halogen, 6000W, (4) FRC Optimum Lightheads Light Tower, 240V, Will-Burt, Night Scan Powerlite 4.5, LED, 120,000 Lumens, (6) FRC Spectra Lightheads Light Tower, 240V, Will-Burt, Night Scan Powerlite 4.5, LED, 80,000 Lumens, (4) FRC Spectra Lightheads Light Tower, 240V, Will-Burt, Night Scan Powerlite 4.5, Quartz Halogen, 6000W, (4) FRC Optimum Lightheads Receiver Tubes, (2) Total, (1) Front, (1) Rear Receiver Tubes, (3) Total, (1) Front, (1) Each Side Receiver Tubes, (3) Total, (1) Rear, (1) Each Side Receiver Tubes, (4) Total, (1) Front, (1) Each Side, (1) Rear Permanent Winch, Warn Industries, 12,000 lb., Driver's Side, International Permanent Winch, Warn Industries, 12,000 lb., Officer's Side, International Permanent Winch, Warn Industries, 12,000 lb., Front Side, International Permanent Winch, Warn Industries, 12,000 lb., Rear Side, International Permanent Winch, Warn Industries, 12,000 lb., Driver's Side, Freightliner Permanent Winch, Warn Industries, 12,000 lb., Officer's Side, Freightliner Permanent Winch, Warn Industries, 12,000 lb., Front Side, Freightliner Permanent Winch, Warn Industries, 12,000 lb., Rear Side, Freightliner Permanent Winch, Warn Industries, 12,000 lb., Driver's Side, Custom Chassis Permanent Winch, Warn Industries, 12,000 lb., Officer's Side, Custom Chassis Permanent Winch, Warn Industries, 12,000 lb., Front Side, Custom Chassis Permanent Winch, Warn Industries, 12,000 lb., Rear Side, Custom Chassis Turn Signals, (2) in Wheel Well Area, LED, Whelen, 600 Series Turn Signals, (2) in Wheel Well Area, LED, Whelen, 70C02SCR Turn Signals, (2) in Wheel Well Area, LED, Whelen, 600 Series, (2) in Rub Rail, LED Truck-Lite, Model 21 Tail Lights, LED, Code 3, 65PKG, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Casting Tail Lights, LED, Code 3, 65PKG4, Stop-Tail (Combination)/Turn/Backup/Warning, 4-Light Vertical Casting Tail Lights, LED, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Individual Bezels Tail Lights, LED, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup/Warning, Dual 2-Light Vertical Castings Tail Lights, LED, Whelen, 900 Series, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Individual Bezels Tail Lights, LED, Whelen, 900 Series, Stop-Tail (Separate)/Turn, 3-Light Vertical Individual Bezels Tail Lights, LED, Whelen, M6 Series, Stop-Tail (Combination)/Turn/Backup, 3-Light Vertical Individual Bezels Tail Lights, LED, Whelen, M6 Series, Stop-Tail (Combination)/Turn/Backup/Warning, 4-Light Vertical Casting (Clear Lenses) Tail Lights, LED, Whelen, M6 Series, Stop-Tail (Combination)/Turn/Backup/Warning, Dual 2-Light Vertical Castings

100238 100242 100244 100246 100248 100250 100252 100254 100256 100258 100260 100266 100267 100268 100269 100270 100271 100272 100273 100274 100275 100276 100277 100278 100279 100280 100281 100282 100283 100284 100285 100286 100287 100288 100289 100290 100291 100292 100108 100109 100110 100111 100112 100122 100124 100126 100127 100128 100129 100130 100131 100132 100133 100134 100135 100136 100137 100138 100139 100140 100141 100145 100146 100149 100150 100153 100155 100157 100159 100161 100163 100165 100184 100185 100188 100189 100192 100194 100196 100198 100200 100202 100204 100206 100208 100210 100212 100214 100216 100218 100220 100222 100224 100226 100228 100230 100232 100234 100236 Tail Lights, LED/Halogen Backup, Whelen, 600 Series, Stop-Tail (Combination)/Turn/Backup, 3-Light Horizontal Casting Generator, Diesel, Anderson, 9kW, D1105-E3BG, FRC Frog Display Generator, Diesel, Onan, 7.5kW, HDKAL, Voltmeter Display Generator, Hydraulic, Harrison, 20kW, MPC, FRC Frog Display Generator, Hydraulic, Smart Power, 20kW, HR-20, Command and Control Center Generator Location, Above Pump Module, Honda Generator Location, Front of Body, Honda Generator Location, L3 Compartment, On Abraded Tray, Exhaust Mounting Under Body, Honda Generator Location, R1 Compartment, On Abraded Tray, Exhaust Mounting Under Body, Honda Generator Location, R3 Compartment, On Abraded Tray, Exhaust Mounting Under Body, Honda Generator Location, T1 Compartment, On Abraded Tray, Exhaust Mounting Under Body, Honda Hose Bed Loading Lights, (2) Front of Hose Bed, Halogen, Whelen, 600 Series Opti-Scene Hose Bed Loading Lights, (2) Front of Hose Bed, Halogen, Whelen, 600 Series Hose Bed Loading Lights, (2) Front of Hose Bed, Halogen, Whelen, 700 Series Hose Bed Loading Lights, (2) Front of Hose Bed, LED, Whelen, 600 Series Opti-Scene Hose Bed Loading Lights, (2) Front of Hose Bed, LED, Grote Hose Bed Loading Lights, (2) Rear, LED, Whelen, PAR 36 Round Floodlight, Black Housing Hose Bed Loading Lights, (2) Rear, Halogen, Unity, AG-R Hose Bed Loading Lights, (2) Rear, Halogen, Collins, CD-FX-12 Hose Bed Loading Lights, (2) Rear, Halogen, Collins, CD-FX-9 Hose Bed Loading Light, (1) Rear, LED, Unity, AG-R P46SLC Hose Bed Loading Lights, (2) Rear, LED, Unity, AG-R P46SLC Hose Bed Loading Lights, (2) Rear, LED, Grote, Trilliant 63901 Pump, Waterous, Single-Stage, 1000 GPM, CSC20, Standard Impellers Pump, Waterous, Single-Stage, 1000 GPM, CSC20, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 1250 GPM, CSC20, Standard Impellers Pump, Waterous, Single-Stage, 1250 GPM, CSC20, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 1500 GPM, CSUC20, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 1750 GPM, CSUC20, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 2000 GPM, CSUC20, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 2250 GPM, CSUC20, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 1500 GPM, CSUD, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 1750 GPM, CSUD, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 2000 GPM, CSUD, Flame Plated Impeller Hubs Pump, Waterous, Two-Stage, 1000 GPM, CMC20, Standard Impellers Pump, Waterous, Two-Stage, 1000 GPM, CMC20, Flame Plated Impeller Hubs Pump, Waterous, Two-Stage, 1250 GPM, CMC20, Standard Impellers Pump, Waterous, Two-Stage, 1250 GPM, CMC20, Flame Plated Impeller Hubs Pump, Waterous, Two-Stage, 1500 GPM, CMUC20, Flame Plated Impeller Hubs Pump, Waterous, Two-Stage, 1750 GPM, CMUC20, Flame Plated Impeller Hubs Pump, Waterous, Two-Stage, 2000 GPM, CMUC20, Flame Plated Impeller Hubs Pump, Waterous, Two-Stage, 2250 GPM, CMUC20, Flame Plated Impeller Hubs Pump, Hale, Single-Stage, 1000 GPM, Qmax, G-Series Pump, Hale, Single-Stage, 1000 GPM, Qmax, K-Series Pump, Hale, Single-Stage, 1250 GPM, Qmax, G-Series Pump, Hale, Single-Stage, 1250 GPM, Qmax, K-Series Pump, Hale, Single-Stage, 1500 GPM, Qmax, G-Series Pump, Hale, Single-Stage, 1500 GPM, Qmax, K-Series Pump, Hale, Single-Stage, 1750 GPM, Qmax, G-Series Pump, Hale, Single-Stage, 1750 GPM, Qmax, K-Series Pump, Hale, Single-Stage, 2000 GPM, Qmax, G-Series Pump, Hale, Single-Stage, 2000 GPM, Qmax, K-Series Pump, Hale, Single-Stage, 2250 GPM, Qmax, G-Series Pump, Hale, Single-Stage, 2250 GPM, Qmax, K-Series Pump, Hale, Single-Stage, 1000 GPM, Qmax XS, G-Series Pump, Hale, Single-Stage, 1250 GPM, Qmax XS, G-Series Pump, Hale, Single-Stage, 1500 GPM, Qmax XS, G-Series Pump, Hale, Single-Stage, 1750 GPM, Qmax XS, G-Series Pump, Hale, Single-Stage, 2000 GPM, Qmax XS, G-Series Pump, Hale, Single-Stage, 2250 GPM, Qmax XS, G-Series Pump, Hale, Single-Stage, 1000 GPM, Qflo-Plus, G-Series Pump, Hale, Single-Stage, 1250 GPM, Qflo-Plus, G-Series Pump, Hale, Two-Stage, 1000 GPM, Qtwo, G-Series, Manual Impellers Pump, Hale, Two-Stage, 1000 GPM, Qtwo, K-Series, Manual Impellers Pump, Hale, Two-Stage, 1250 GPM, Qtwo, G-Series, Manual Impellers Pump, Hale, Two-Stage, 1250 GPM, Qtwo, K-Series, Manual Impellers Pump, Hale, Two-Stage, 1500 GPM, Qtwo, G-Series, Manual Impellers Pump, Hale, Two-Stage, 1500 GPM, Qtwo, K-Series, Manual Impellers Pump, Hale, Two-Stage, 1750 GPM, Qtwo, G-Series, Manual Impellers Pump, Hale, Two-Stage, 1750 GPM, Qtwo, K-Series, Manual Impellers Pump, Hale, Two-Stage, 2000 GPM, Qtwo, G-Series, Manual Impellers Pump, Hale, Two-Stage, 2000 GPM, Qtwo, K-Series, Manual Impellers Pump Shift and Lights, Waterous, Air-Operated Pump Shift and Lights, Waterous, Air-Operated, Manual Override Pump Shift and Lights, Hale, Air-Operated Pump Shift and Lights, Hale, Air-Operated, Manual Override Pump Shift and Lights, Darley, Air-Operated, Manual Override Pump Shift, Chassis Sup/Instl, Electric-Over-Air, Light on Pump Panel Pump Shift, Chassis Sup/Instl, Electric-Over-Air, Lights Incorporated with Pres. Gov.

Hot Shift PTO Connection, Pump and Roll Capability Pump Manuals Hale, (3) Pump Manuals Hale, (4) Pump Manuals Hale, (5) Pump Manuals Hale, (6) Discharge Relief Valve, Waterous, Enfo IV, Vernier Throttle, Pump Hour Meter Discharge Relief Valve, Hale, Enfo IV, Vernier Throttle, Pump Hour Meter Total Pressure Master (TPM), Hale, Enfo IV, Vernier Throttle, Pump Hour Meter Dual Total Pressure Master (TPM), Hale, Enfo IV, Vernier Throttle, Pump Hour Meter Discharge Relief Valve, Darley, Enfo IV, Vernier Throttle, Pump Hour Meter Governor, Total Pressure Governor (TPG), Class 1, With Sun Shield Governor, Total Pressure Governor Plus (TPG+), Class 1, With Sun Shield Primer, Waterous, VPO/VPOS Oilless, VAP Primer, Waterous, VPO/VPOS Oilless, Multi-VAP, Remote Prime on Officer's Side Steamer Primer, Waterous, VPO/VPOS Oilless, Multi-VAP, Remote Prime on Rear Steamer Primer, Waterous, VPO/VPOS Oilless, Multi-VAP, Remote Prime on Front Steamer Primer, Waterous, VPO/VPOS Lubricated, VAP Primer, Waterous, VPO/VPOS Lubricated, Multi-VAP, Remote Prime on Officer's Side Steamer Primer, Waterous, VPO/VPOS Lubricated, Multi-VAP, Remote Prime on Rear Steamer Primer, Waterous, VPO/VPOS Lubricated, Multi-VAP, Remote Prime on Front Steamer

100364 100365 100366 100367 100368 100369 100370 100371 100372 100377 100378 100379 100380 100381 100382 100383 100384 100385 100386 100387 100388 100389 100390 100391 100392 100393 100394 100395 100396 100429 100430 100431 100432 100433 100434 100435 100436 100437 100293 100294 100295 100296 100297 100298 100299 100300 100301 100302 100303 100304 100305 100306 100307 100308 100309 100310 100311 100312 100313 100314 100315 100316 100317 100318 100319 100320 100321 100322 100323 100334 100335 100336 100337 100338 100339 100340 100341 100342 100343 100344 100345 100346 100347 100348 100349 100350 100351 100352 100353 100354 100355 100356 100357 100358 100359 100360 100361 100362 100363 Primer, Hale ESP, SPV Primer, Hale ESP, PVG Primer, Hale ESP, PVG, Remote Prime on Officer's Side Steamer Primer, Hale ESP, PVG, Remote Prime on Rear Steamer Primer, Hale ESP, PVG, Remote Prime on Front Steamer Primer, 2 Pumps, Hale ESP, PVG Primer, 2 Pumps, Hale ESP, PVG, Remote Prime on Officer's Side Steamer Primer, 2 Pumps, Hale ESP, PVG, Remote Prime on Rear Steamer Primer, 2 Pumps, Hale ESP, PVG, Remote Prime on Front Steamer Primer, Trident, AirPrime (3-Barrel), Remote Prime on Officer's Side Steamer Primer, Trident, AirPrime (3-Barrel), Remote Prime on Rear Steamer Primer, Trident, AirPrime (3-Barrel), Remote Prime on Front Steamer Primer, Trident, AirPrime (3-Barrel), Auto Prime and Vacuum Gauge Primer, Trident, AirPrime (3-Barrel), Auto Prime and Vacuum Gauge, Hale Direct Primer, Trident, AirPrime (3-Barrel), Auto Prime and Vacuum Gauge, Remote Prime on Officer's Side Steamer Primer, Trident, AirPrime (3-Barrel), Auto Prime and Vacuum Gauge, Remote Prime on Rear Steamer Primer, Trident, AirPrime (3-Barrel), Auto Prime and Vacuum Gauge, Remote Prime on Front Steamer Tank to Pump, 3", Akron 8800 3" Manual Valve, IC Push-Pull Handle Tank to Pump, 3", Akron 8900 3" Manual Valve, IC Push-Pull Handle Tank to Pump, 3", Akron 8800 3" Manual Valve, IC Top Mount Handle Tank to Pump, 3", Akron 8900 3" Manual Valve, IC Top Mount Handle Tank to Pump, 3", Akron 8600 3" Manual Valve, Class 1 Air Cylinder and Switch Tank to Pump, 3", Akron 8600 3" Electric Valve, 9323 Controller Tank to Pump, 3", Akron 8800/KZ Co 3" Electric Valve, Omni Controller Tank to Pump, 3", Akron 8600 3" Gear Valve, 4" Handwheel Tank to Pump, 3", Elkhart 3" Manual Valve, IC Push-Pull Handle Tank to Pump, 3", Elkhart 3" Manual Valve, IC Top Mount Handle Tank to Pump, 3", Elkhart 3" Electric Valve, UBEC1 Controller Tank to Pump, 3", Elkhart 3" Gear Valve, 6.3" Handwheel Tank to Pump, 3", Waterous 3.5" Rotary Valve, Crank Handle Tank to Pump, 3", Waterous 3.5" Electric Valve, Electric Controller Tank to Pump, 4", Akron 8800 3" Manual Valve, IC Push-Pull Handle Tank to Pump, 4", Akron 8900 3" Manual Valve, IC Push-Pull Handle Tank to Pump, 4", Akron 8800 3" Manual Valve, IC Top Mount Handle Tank to Pump, 4", Akron 8900 3" Manual Valve, IC Top Mount Handle Tank to Pump, 4", Akron 8800 4" Electric Valve, 9323 Controller Tank to Pump, 4", Akron 8900 4" Electric Valve, 9323 Controller Tank to Pump, 4", Akron 8800/KZ Co 3" Electric Valve, Omni Controller Tank to Pump, 4", Akron 8800 4" Gear Valve, 6" Handwheel Tank to Pump, 4", Akron 8900 4" Gear Valve, 6" Handwheel Tank to Pump, 4", Elkhart 3" Manual Valve, IC Push-Pull Handle Tank to Pump, 4", Elkhart 3" Manual Valve, IC Top Mount Handle Tank to Pump, 4", Elkhart 4" Electric Valve, UBEC1 Controller Tank to Pump, 4", Elkhart 4" Gear Valve, 6.3" Handwheel Tank to Pump, 4", Waterous 3.5" Rotary Valve, Crank Handle Tank to Pump, 4", Waterous 3.5" Electric Valve, Electric Controller Pump to Tank Fill, 2", Akron 8800 2" Manual Valve, IC Push-Pull Handle Pump to Tank Fill, 2", Akron 8900 2" Manual Valve, IC Push-Pull Handle Pump to Tank Fill, 2", Akron 8800 2" Manual Valve, IC Top Mount Handle Pump to Tank Fill, 2", Akron 8900 2" Manual Valve, IC Top Mount Handle Pump to Tank Fill, 2", Akron 8600 2" Electric Valve, 9323 Controller Pump to Tank Fill, 2", Akron 8800/KZ Co 2" Electric Valve, Omni Controller Pump to Tank Fill, 2", Elkhart 2" Manual Valve, IC Push-Pull Handle Pump to Tank Fill, 2", Elkhart 2" Manual Valve, IC Top Mount Handle Pump to Tank Fill, 2", Elkhart 2" Electric Valve, UBEC1 Controller Pump to Tank Fill, 2", Waterous 2.5" Rotary Valve, Crank Handle Pump to Tank Fill, 2", Waterous 2.5" Electric Valve, Electric Controller Pump to Tank Fill, 2.5", Akron 8800 2.5" Manual Valve, IC Push-Pull Handle Pump to Tank Fill, 2.5", Akron 8900 2.5" Manual Valve, IC Push-Pull Handle Pump to Tank Fill, 2.5", Akron 8800 2.5" Manual Valve, IC Top Mount Handle Pump to Tank Fill, 2.5", Akron 8900 2.5" Manual Valve, IC Top Mount Handle Pump to Tank Fill, 2.5", Akron 8600 2.5" Electric Valve, 9323 Controller Pump to Tank Fill, 2.5", Akron 8800/KZ Co 2.5" Electric Valve, Omni Controller Pump to Tank Fill, 2.5", Akron 8600 2.5" Gear Valve, 4" Handwheel Pump to Tank Fill, 2.5", Elkhart 2.5" Manual Valve, IC Push-Pull Handle Pump to Tank Fill, 2.5", Elkhart 2.5" Manual Valve, IC Top Mount Handle Pump to Tank Fill, 2.5", Elkhart 2.5" Electric Valve, UBEC1 Controller Pump to Tank Fill, 2.5", Elkhart 2.5" Gear Valve, 6.3" Handwheel Pump to Tank Fill, 2.5", Waterous 2.5" Rotary Valve, Crank Handle Pump to Tank Fill, 2.5", Waterous 2.5" Electric Valve, Electric Controller Drains, Innovative Controls, Manual Lift Handle Drains, Innovative Controls, Manual Lift Handle, Class 1 Auto Drains on Pre-Connects Steamer, Driver Side, 5", Short Tube, Full-Body Pump, MNST Steamer, Driver Side, 5", Short Tube, Volute Pump, MNST Steamer, Driver Side, 6", Short Tube, Full-Body Pump, MNST Steamer, Driver Side, 6", Short Tube, Volute Pump, MNST Steamer, Officer Side, 5", Short Tube, Full-Body Pump, MNST Steamer, Officer Side, 5", Short Tube, Volute Pump, MNST Steamer, Officer Side, 6", Short Tube, Full-Body Pump, MNST Steamer, Officer Side, 6", Short Tube, Volute Pump, MNST Steamer, Rear, 4" MNST Steamer, Rear, 5" MNST Steamer, Front, Driver's Side, 6", Horizontal, 5" Piping, Commercial Chassis, MNST Steamer, Front, Driver's Side, 6", Horizontal, 5" Piping, Custom Chassis, MNST Steamer, Front, Driver's Side, 6", Vertical, 5" Piping, Commercial Chassis, MNST Steamer, Front, Driver's Side, 6", Vertical, 5" Piping, Custom Chassis, MNST Steamer, Front, Officer's Side, 6", Horizontal, 5" Piping, Commercial Chassis, MNST Steamer, Front, Officer's Side, 6", Horizontal, 5" Piping, Custom Chassis, MNST Steamer, Front, Officer's Side, 6", Vertical, 5" Piping, Commercial Chassis, MNST Steamer, Front, Officer's Side, 6", Vertical, 5" Piping, Custom Chassis, MNST Butterfly Valve, 5" Air, Neles Jamesbury, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 5" Electric, Akron, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 5" Electric, Elkhart, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Air, Neles Jamesbury, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Air, Waterous Monarch, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Electric, Akron, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Electric, Darley, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Electric, Elkhart, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Electric, Hale MIV-E, Hale Bleeder and IRV, Manual Override Access

100499 100500 100501 100502 100503 100504 100505 100506 100507 100508 100509 100510 100511 100512 100513 100514 100515 100516 100517 100518 100519 100520 100521 100522 100523 100524 100525 100526 100527 100528 100529 100530 100531 100532 100533 100534 100535 100536 100438 100439 100440 100441 100442 100443 100444 100445 100446 100447 100448 100449 100450 100451 100452 100453 100454 100455 100456 100457 100458 100459 100460 100461 100462 100463 100464 100465 100466 100467 100468 100469 100470 100471 100472 100473 100474 100475 100476 100477 100478 100479 100480 100481 100482 100483 100484 100485 100486 100487 100488 100489 100490 100491 100492 100493 100494 100495 100496 100497 100498 Butterfly Valve, 6" Electric, Waterous Monarch, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Manual, Darley, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Manual, Hale MIV-M, Hale Bleeder and IRV Butterfly Valve, 6" Manual, Neles Jamesbury, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Manual, Waterous Monarch, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 5" Air, Neles Jamesbury, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 5" Electric, Akron, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 5" Electric, Elkhart, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Air, Neles Jamesbury, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Air, Waterous Monarch, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Electric, Akron, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Electric, Darley, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Electric, Elkhart, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Electric, Waterous Monarch, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Manual, Darley, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Manual, Neles Jamesbury, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Manual, Waterous Monarch, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 5" Air, Neles Jamesbury, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 5" Electric, Akron, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 5" Electric, Elkhart, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Air, Neles Jamesbury, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Air, Waterous Monarch, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Electric, Darley, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 6" Electric, Hale MIV-E, Hale Bleeder and IRV, Manual Override Access Butterfly Valve, 6" Electric, Waterous Monarch, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 5" Air, Neles Jamesbury, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 5" Electric, Akron, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 5" Electric, Elkhart, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Air, Neles Jamesbury, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Air, Waterous Monarch, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Electric, Darley, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 6" Electric, Waterous Monarch, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 5" Electric, Akron, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 5" Electric, Elkhart, Manual Override Access, Class 1 Bleeder, Elkhart IRV Butterfly Valve, 5" Electric, Akron, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Butterfly Valve, 5" Electric, Elkhart, Manual Override Access, Class 1 Bleeder, Trident AirMax IRV Elbow (30 Deg.) 5" FNST x 4" Storz 30 Degree Elbow, 4" Cap and Chain, Rocker Lug, TFT Elbow (30 Deg.) 5" FNST x 5" Storz 30 Degree Elbow, 5" Cap and Chain, Rocker Lug, TFT Elbow (30 Deg.) 6" FNST x 4" Storz 30 Degree Elbow, 4" Cap and Chain, Rocker Lug, TFT Elbow (30 Deg.) 6" FNST x 5" Storz 30 Degree Elbow, 5" Cap and Chain, Rocker Lug, TFT Discharge, Driver-Side, 2-1/2", NST, 3" Plumbing (250 GPM) Discharge, Driver-Side, 3", NST (375 GPM) Discharge, Driver-Side, 4", NST (625 GPM) Discharge, Officer-Side, 2-1/2", NST, 3" Plumbing Discharge, Officer-Side, 3", NST Discharge, Front Bumper Center, 2-1/2", In Hosewell, NST Discharge, Front Bumper Driver-Side, 1-1/2", Above Gravelshield, NPSH Discharge, Front Bumper Driver-Side, 1-1/2", Above Gravelshield, NST, Controlled at Bumper Discharge, Front Bumper Driver-Side, 1-1/2", Above Gravelshield, NPSH, Controlled at Bumper Discharge, Front Bumper Driver-Side, 1-1/2", In Hosewell, NPSH Discharge, Front Bumper Driver-Side, 2-1/2", Above Gravelshield, NST, 3" Plumbing Discharge, Front Bumper Driver-Side, 2-1/2", In Hosewell, NST Discharge, Front Bumper Officer-Side, 1-1/2", Above Gravelshield, NPSH Discharge, Front Bumper Officer-Side, 1-1/2", In Hosewell, NPSH Discharge, Front Bumper Officer-Side, 2-1/2", Above Gravelshield, NST, 3" Plumbing Discharge, Front Bumper Officer-Side, 2-1/2", In Hosewell, NST Discharge, Rear Driver-Side, 1-1/2", NST Discharge, Rear Driver-Side, 1-1/2", NPSH Discharge, Rear Driver-Side, 2-1/2", NST, 3" Plumbing Discharge, Rear Driver-Side, 3", NST Discharge, Rear Officer-Side, 1-1/2", NST Discharge, Rear Officer-Side, 1-1/2", NPSH Discharge, Rear Officer-Side, 2-1/2", NST, 3" Plumbing Discharge, Rear Officer-Side, 3", NST Discharge, Rear Officer-Side, 4", NST Preconnect, Hose Bed Driver-Side, 1-1/2", NST Preconnect, Hose Bed Driver-Side, 1-1/2", NPSH Preconnect, Hose Bed Driver-Side, 2-1/2", NST, 3" Plumbing Preconnect, Hose Bed Driver-Side, 3", NST Preconnect, Hose Bed Officer-Side, 1-1/2", NST Preconnect, Hose Bed Officer-Side, 1-1/2", NPSH Preconnect, Hose Bed Officer-Side, 2-1/2", NST, 3" Plumbing Preconnect, Hose Bed Officer-Side, 3", NST Deluge, Center, 3", Four-Bolt Flange (375 GPM) Deluge, Center, 3", NPT (375 GPM) Deluge, Center, 3", Victaulic Deluge, Center, 4", Eight-Bolt Flange (625 GPM) Deluge, Center, 4", NPT (625 GPM) Deluge, Center, 4", Victaulic Deluge, Driver-Side, 3", Four-Bolt Flange Deluge, Driver-Side, 3", NPT (375 GPM) Deluge, Driver-Side, 3", Victaulic Deluge, Officer-Side, 3", Four-Bolt Flange Deluge, Officer-Side, 3", NPT (375 GPM) Deluge, Officer-Side, 3", Victaulic Cap, NST, 1-1/2", Chrome, Trident Cap, NPSH, 1-1/2", Chrome, Trident Cap, NST, 2-1/2", Chrome, Trident Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, Trident Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, Trident Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Preconnect, Chrome, Trident Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Preconnect, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Preconnect, Chrome, Trident Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" Male Special Thread - Male Special Thread Cap, Chrome, Trident Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" Male Special Thread - Male Special Thread Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" Male Special Thread - Male Special Thread Cap, Chrome, Trident

100598 100599 100600 100601 100602 100603 100604 100605 100606 100607 100608 100609 100610 100611 100612 100613 100614 100615 100616 100617 100618 100619 100620 100621 100622 100623 100624 100625 100626 100627 100628 100629 100630 100631 100632 100633 100634 100636 100537 100538 100539 100540 100541 100542 100543 100544 100545 100546 100547 100548 100549 100550 100551 100552 100553 100554 100555 100556 100557 100558 100559 100560 100561 100562 100563 100564 100565 100566 100567 100568 100569 100570 100571 100572 100573 100574 100575 100576 100577 100578 100579 100580 100581 100582 100583 100584 100585 100586 100587 100588 100589 100590 100591 100592 100593 100594 100595 100596 100597 Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" Male Special Thread - Male Special Thread Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" Male Special Thread - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" Male Special Thread - Preconnect, Chrome, Trident Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" Male Special Thread - Preconnect, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" Male Special Thread - Preconnect, Chrome, Trident Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNST - NST Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNST - NST Cap, Chrome, Trident Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNPSH - NPSH Cap, Chrome, Trident Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNST - Preconnect, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNST - Preconnect, Chrome, Trident Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNPSH - Preconnect, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNPSH - Preconnect, Chrome, Trident Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MAMA - AMA Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MAMA - Preconnect, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MAMA - Adapter, 2-1/2" FAMA x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MAMA - Adapter, 2-1/2" FAMA x 1-1/2" MNPSH - Preconnect, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MBCT - BCT Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MBCT - Preconnect, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MBCT - Adapter, 2-1/2" FBCT x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MBCT - Adapter, 2-1/2" FBCT x 1-1/2" MNPSH - Preconnect, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MCSA - CSA Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MCSA - Preconnect, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MCSA - Adapter, 2-1/2" FCSA x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Elbow (45 Deg.) 2-1/2" FNST x 2-1/2" MCSA - Adapter, 2-1/2" FCSA x 1-1/2" MNPSH - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNST - NST Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNST - NST Cap, Chrome, Trident Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNPSH - NPSH Cap, Chrome, Trident Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNST - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNST - Preconnect, Chrome, Trident Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNPSH - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MNST - Adapter, 2-1/2" FNST x 1-1/2" MNPSH - Preconnect, Chrome, Trident Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MAMA - AMA Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MAMA - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MAMA - Adapter, 2-1/2" FAMA x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MAMA - Adapter, 2-1/2" FAMA x 1-1/2" MNPSH - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MBCT - BCT Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MBCT - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MBCT - Adapter, 2-1/2" FBCT x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MBCT - Adapter, 2-1/2" FBCT x 1-1/2" MNPSH - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MCSA - CSA Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MCSA - Preconnect, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MCSA - Adapter, 2-1/2" FCSA x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Elbow (30 Deg.) 2-1/2" FNST x 2-1/2" MCSA - Adapter, 2-1/2" FCSA x 1-1/2" MNPSH - Preconnect, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MAMA - Preconnect, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MAMA - Adapter, 2-1/2" FAMA x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MAMA - Adapter, 2-1/2" FAMA x 1-1/2" MNPSH - Preconnect, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MBCT - Preconnect, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MBCT - Adapter, 2-1/2" FBCT x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MBCT - Adapter, 2-1/2" FBCT x 1-1/2" MNPSH - Preconnect, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MCSA - Preconnect, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MCSA - Adapter, 2-1/2" FCSA x 1-1/2" MNPSH - NPSH Cap, Chrome, South Park Adapter, 2-1/2" FNST x 2-1/2" MCSA - Adapter, 2-1/2" FCSA x 1-1/2" MNPSH - Preconnect, Chrome, South Park Elbow (30 Deg.) 3" FNST x 3" MNST - NST Cap, Chrome, Trident Elbow (30 Deg.) 3" FNST x 3" MNST - NST Cap, Chrome, South Park Elbow (45 Deg.) 3" FNST x 3" MNST - NST Cap, Chrome, Trident Elbow (30 Deg.) 3" FNST x 2-1/2" MNST - NST Cap, Chrome, Trident Elbow (45 Deg.) 3" FNST x 2-1/2" MNST - NST Cap, Chrome, Trident Elbow (45 Deg.) 3" FNST x 2-1/2" MNST - NST Cap, Chrome, South Park Elbow (30 Deg.) 3" FNST x 2-1/2" MNST - Preconnect, Chrome, Trident Elbow (45 Deg.) 3" FNST x 2-1/2" MNST - Preconnect, Chrome, South Park Elbow (45 Deg.) 3" FNST x 2-1/2" MNST - Preconnect, Chrome, Trident Elbow (30 Deg.) 3" FNST x 2-1/2" Male Special Thread - Male Special Thread Cap, Chrome, Trident Elbow (45 Deg.) 3" FNST x 2-1/2" Male Special Thread - Male Special Thread Cap, Chrome, Trident Elbow (45 Deg.) 3" FNST x 2-1/2" Male Special Thread - Male Special Thread Cap, Chrome, South Park Elbow (30 Deg.) 3" FNST x 2-1/2" Male Special Thread - Preconnect, Chrome, Trident Elbow (45 Deg.) 3" FNST x 2-1/2" Male Special Thread - Preconnect, Chrome, South Park Elbow (45 Deg.) 3" FNST x 2-1/2" Male Special Thread - Preconnect, Chrome, Trident Elbow (30 Deg.) 3" FNST x 4" Storz - Storz Cap, TFT Elbow (30 Deg.) 3" FNST x 5" Storz - Storz Cap, TFT Elbow (30 Deg.) 4" FNST x 4" MNST - NST Cap, Chrome, Trident Elbow (30 Deg.) 4" FNST x 4" MNST - NST Cap, Chrome, South Park Elbow (45 Deg.) 4" FNST x 4" MNST - NST Cap, Chrome, Trident Direct Tank Fill Fittings, Elbow (30 Deg.) 4" FNST x 4" Storz, Storz Cap, TFT Direct Tank Fill Fittings, Elbow (30 Deg.) 4" FNST x 5" Storz, Storz Cap, TFT Elbow (30 Deg.) 4" FNST x 4" Storz - Adapter, 4" Storz x 2-1/2" NST, TFT - Cap, Chrome, South Park Elbow (30 Deg.) 4" FNST x 4" Storz - Adapter, 4" Storz x 2-1/2" NST, TFT - Cap, Chrome, Trident Elbow (30 Deg.) 4" FNST x 4" Storz - Adapter, 4" Storz x 2-1/2" Male Special Thread, TFT - Cap, Chrome, South Park Elbow (30 Deg.) 4" FNST x 4" Storz - Adapter, 4" Storz x 2-1/2" Male Special Thread, TFT - Cap, Chrome, Trident Elbow (30 Deg.) 4" FNST x 5" Storz - Adapter, 5" Storz x 2-1/2" NST, TFT - Cap, Chrome, South Park Elbow (30 Deg.) 4" FNST x 5" Storz - Adapter, 5" Storz x 2-1/2" NST, TFT - Cap, Chrome, Trident Elbow (30 Deg.) 4" FNST x 5" Storz - Adapter, 5" Storz x 2-1/2" Male Special Thread, TFT - Cap, Chrome, South Park Elbow (30 Deg.) 4" FNST x 5" Storz - Adapter, 5" Storz x 2-1/2" Male Special Thread, TFT - Cap, Chrome, Trident Cap, NST, 1-1/2", Chrome, South Park AutoFill, Waterous, Driver Side Pump Panel, 2-1/2" Inlet AutoFill, Waterous, Driver Side Steamer Valve AutoFill, Waterous, Driver, Officer and Front Steamer Valves AutoFill, Waterous, Officer and Front Steamer Valves AutoFill, Waterous, Front Steamer Valve AutoFill, Waterous, Officer Side Pump Panel AutoFill, Waterous, Officer Side Steamer Valve Valve, 2", Akron, Gear, 8620, Stainless Ball, 4" Handwheel with Vert. Position Indicator Valve, 2", Akron, Electric, 8620, Stainless Ball, 9323 Navigator Pro Controller (Valve Only) Valve, 2", Akron, Electric, 8620, Stainless Ball, 9325 Navigator Pro Controller (Valve and Pressure) Valve, 2", Akron, Electric, 8620, Stainless Ball, 9325 Navigator Pro Controller (Valve, Pressure, Flow) Valve, 2", Akron, Electric (KZ Co.), 8620, Stainless Ball, OMNI Display Controller (Valve Only) Valve, 2", Akron, Electric (KZ Co.), 8620, Stainless Ball, OMNI Display Controller (Valve and Pressure) Valve, 2-1/2", Akron, Gear, 8625, Stainless Ball, 4" Handwheel with Vert. Position Indicator

100699 100700 100701 100702 100704 100705 100706 100707 100708 100709 100710 100711 100712 100713 100714 100715 100716 100717 100718 100719 100720 100721 100722 100723 100724 100725 100726 100727 100728 100729 100730 100731 100732 100733 100734 100735 100736 100737 100637 100638 100639 100640 100641 100642 100643 100644 100645 100646 100647 100648 100649 100650 100651 100652 100653 100654 100655 100656 100657 100658 100659 100660 100661 100662 100663 100664 100665 100667 100668 100669 100670 100671 100672 100673 100674 100675 100676 100677 100678 100679 100680 100681 100682 100683 100684 100685 100686 100687 100688 100689 100690 100691 100692 100693 100694 100695 100696 100697 100698 Valve, 2-1/2", Akron, Electric, 8625, Stainless Ball, 9323 Navigator Pro Controller (Valve Only) Valve, 2-1/2", Akron, Electric, 8625, Stainless Ball, 9325 Navigator Pro Controller (Valve and Pressure) Valve, 2-1/2", Akron, Electric, 8625, Stainless Ball, 9325 Navigator Pro Controller (Valve, Pressure, Flow) Valve, 2-1/2", Akron, Electric (KZ Co.), 8625, Stainless Ball, OMNI Display Controller (Valve Only) Valve, 2-1/2", Akron, Electric (KZ Co.), 8625, Stainless Ball, OMNI Display Controller (Valve and Pressure) Valve, 3", Akron, Gear, 8630, Stainless Ball, 4" Handwheel with Vert. Position Indicator Valve, 3", Akron, Electric, 8630, Stainless Ball, 9323 Navigator Pro Controller (Valve Only) Valve, 3", Akron, Electric, 8630, Stainless Ball, 9325 Navigator Pro Controller (Valve and Pressure) Valve, 3", Akron, Electric, 8630, Stainless Ball, 9325 Navigator Pro Controller (Valve, Pressure, Flow) Valve, 3", Akron, Electric (KZ Co.), 8630, Stainless Ball, OMNI Display Controller (Valve Only) Valve, 3", Akron, Electric (KZ Co.), 8630, Stainless Ball, OMNI Display Controller (Valve and Pressure) Valve, 1-1/2", Akron, Manual, 8815, Stainless Ball, Innovative Controls Push Pull Controller Valve, 1-1/2", Akron, Manual, 8815, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Valve, 1-1/2", Akron, Manual, 8815, Stainless Ball, Innovative Controls Top Mount Handle Valve, 1-1/2", Akron, Manual, 8815, Stainless Ball, Elkhart RC-10 Handwheel Valve, 1-1/2", Akron, Manual (Air Cylinder), 8815, Stainless Ball, Williams Air Controller Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Top Mount Handle Valve, 2", Akron, Manual, 8820, Stainless Ball, Elkhart RC-10 Handwheel Valve, 2", Akron, Manual (Air Cylinder), 8820, Stainless Ball, Williams Air Controller Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Top Mount Handle Valve, 2-1/2", Akron, Manual, 8825, Stainless Ball, Elkhart RC-10 Handwheel Valve, 3", Akron, Manual, Slow Close, 8830, Stainless Ball, Innovative Controls Top Mount Handle Valve, 3", Akron, Manual, Slow Close, 8830, Stainless Ball, Elkhart RC-10 Handwheel Valve, 4", Akron, Gear, 8840, Stainless Ball, 6" Handwheel with Vert. Position Indicator Valve, 4", Akron, Electric, 8840, Stainless Ball, 9323 Navigator Pro Controller (Valve Only) Valve, 4", Akron, Electric, 8840, Stainless Ball, 9325 Navigator Pro Controller (Valve and Pressure) Valve, 4", Akron, Electric, 8840, Stainless Ball, 9325 Navigator Pro Controller (Valve, Pressure, Flow) Valve, 1-1/2", Akron, Manual, 8915, Composite Ball, Innovative Controls Push Pull Controller Valve, 1-1/2", Akron, Manual, 8915, Composite Ball, Innovative Controls Push Pull Controller (Operators Panel) Valve, 1-1/2", Akron, Manual, 8915, Composite Ball, Innovative Controls Top Mount Handle Valve, 1-1/2", Akron, Manual, 8915, Composite Ball, Elkhart RC-10 Handwheel Valve, 1-1/2", Akron, Manual (Air Cylinder), 8915, Composite Ball, Williams Air Controller Valve, 2", Akron, Manual, 8920, Composite Ball, Innovative Controls Push Pull Controller Valve, 2", Akron, Manual, 8920, Composite Ball, Innovative Controls Push Pull Controller (Operators Panel) Valve, 2", Akron, Manual, 8920, Composite Ball, Innovative Controls Top Mount Handle Valve, 2", Akron, Manual, 8920, Composite Ball, Elkhart RC-10 Handwheel Valve, 2", Akron, Manual (Air Cylinder), 8920, Composite Ball, Williams Air Controller Valve, 2-1/2", Akron, Manual, 8925, Composite Ball, Innovative Controls Push Pull Controller Valve, 2-1/2", Akron, Manual, 8925, Composite Ball, Innovative Controls Push Pull Controller (Operators Panel) Valve, 2-1/2", Akron, Manual, 8925, Composite Ball, Innovative Controls Top Mount Handle Valve, 2-1/2", Akron, Manual, 8925, Composite Ball, Elkhart RC-10 Handwheel Valve, 3", Akron, Manual, Slow Close, 8930, Composite Ball, Innovative Controls Top Mount Handle Valve, 3", Akron, Manual, Slow Close, 8930, Composite Ball, Elkhart RC-10 Handwheel Valve, 4", Akron, Gear, 8940, Composite Ball, 6" Handwheel with Vert. Position Indicator Valve, 4", Akron, Electric, 8940, Composite Ball, 9323 Navigator Pro Controller (Valve Only) Valve, 4", Akron, Electric, 8940, Composite Ball, 9325 Navigator Pro Controller (Valve and Pressure) Valve, 4", Akron, Electric, 8940, Composite Ball, 9325 Navigator Pro Controller (Valve, Pressure, Flow) Valve, 1-1/2", Elkhart, Manual, EB15-R1F, Stainless Ball, Innovative Controls Push Pull Controller Valve, 1-1/2", Elkhart, Manual, EB15-R1F, Stainless Ball, Innovative Controls Top Mount Handle Valve, 1-1/2", Elkhart, Manual, EB15-R1F, Stainless Ball, Elkhart RC-10 Handwheel Valve, 1-1/2", Elkhart, Manual (Air Cylinder), EB15-R1F, Stainless Ball, Williams Air Controller Valve, 2", Elkhart, Manual, EB20-R1F, Stainless Ball, Innovative Controls Push Pull Controller Valve, 2", Elkhart, Manual, EB20-R1F, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Valve, 2", Elkhart, Manual, EB20-R1F, Stainless Ball, Innovative Controls Top Mount Handle Valve, 2", Elkhart, Manual, EB20-R1F, Stainless Ball, Elkhart RC-10 Handwheel Valve, 2", Elkhart, Manual, EB20-D2F, Stainless Ball, D2 Handle Valve, 2", Elkhart, Gear, EB20-G1F, Stainless Ball, Elkhart 6.3" Handwheel with Position Indicator Valve, 2", Elkhart, Electric, EB20-E1F, Stainless Ball, UBEC1 Controller (Valve Only) Valve, 2", Elkhart, Electric, EB20-E1F, Stainless Ball, UBEC2 Controller (Valve and Pressure) Valve, 2", Elkhart, Electric, EB20-E1F, Stainless Ball, UBEC3 Controller (Valve, Pressure, Flow) Valve, 2-1/2", Elkhart, Manual, EB25-R1F, Stainless Ball, Innovative Controls Push Pull Controller Valve, 2-1/2", Elkhart, Manual, EB25-R1F, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Valve, 2-1/2", Elkhart, Manual, EB25-R1F, Stainless Ball, Innovative Controls Top Mount Handle Valve, 2-1/2", Elkhart, Manual, EB25-R1F, Stainless Ball, Elkhart RC-10 Handwheel Valve, 2-1/2", Elkhart, Gear, EB25-G1F, Stainless Ball, Elkhart 6.3" Handwheel with Position Indicator Valve, 2-1/2", Elkhart, Electric, EB25-E1F, Stainless Ball, UBEC1 Controller (Valve Only) Valve, 2-1/2", Elkhart, Electric, EB25-E1F, Stainless Ball, UBEC2 Controller (Valve and Pressure) Valve, 2-1/2", Elkhart, Electric, EB25-E1F, Stainless Ball, UBEC3 Controller (Valve, Pressure, Flow) Valve, 3", Elkhart, Manual, Slow Close, EB30-R1S, Stainless Ball, Innovative Controls Top Mount Handle Valve, 3", Elkhart, Manual, Slow Close, EB30-R1F, Stainless Ball, Elkhart RC-10 Handwheel Valve, 3", Elkhart, Gear, EB30-G1F, Stainless Ball, Elkhart 6.3" Handwheel with Position Indicator Valve, 3", Elkhart, Electric, EB30-E1F, Stainless Ball, UBEC1 Controller (Valve Only) Valve, 3", Elkhart, Electric, EB30-E1F, Stainless Ball, UBEC2 Controller (Valve and Pressure) Valve, 3", Elkhart, Electric, EB30-E1F, Stainless Ball, UBEC3 Controller (Valve, Pressure, Flow) Valve, 4", Elkhart, Gear, EB40-G1F, Stainless Ball, Elkhart 6.3" Handwheel with Position Indicator Valve, 4", Elkhart, Electric, EB40-E1F, Stainless Ball, UBEC1 Controller (Valve Only) Valve, 4", Elkhart, Electric, EB40-E1F, Stainless Ball, UBEC2 Controller (Valve and Pressure) Valve, 4", Elkhart, Electric, EB40-E1F, Stainless Ball, UBEC3 Controller (Valve, Pressure, Flow) Foam System, FoamPro, 1600, Single System, Class A Foam, Flush System Foam System, FoamPro, 2001, Single System, Class A Foam, Flush System Foam System, FoamPro, 2001, Single System, Class B Foam, Flush System Foam System, FoamPro, 2002, Single System, Class A Foam, Flush System Foam System, FoamPro, 2002, Single System, Class B Foam, Flush System Foam System, FoamPro, 3012 (Hydraulic), Single System, Class A Foam, Flush System Foam System, Waterous, Aquis 2.5, Single System, Class A Foam, NO Optional Flush System Foam System, Waterous, Aquis 2.5, Single System, Class A Foam, Flush System Foam System, Waterous, Advantus 3, Single System, Class A Foam, Flush System Foam System, Waterous, Advantus 3, Single System, Class B Foam, Flush System Foam System, Waterous, Advantus 6, Single System, Class A Foam, Flush System Foam System, Waterous, Advantus 6, Single System, Class B Foam, Flush System Foam System, Hale, FoamLogix 3.3, Single System, Class A Foam, NO Optional Flush System Foam System, Hale, FoamLogix 3.3, Single System, Class A Foam, Flush System Foam System, Hale, FoamLogix 3.3, Single System, Class B Foam, Flush System Foam System, Hale, FoamLogix 5.0, Single System, Class A Foam, NO Optional Flush System Foam System, Hale, FoamLogix 5.0, Single System, Class A Foam, Flush System

100799 100800 100801 100802 100803 100804 100805 100806 100807 100808 100809 100810 100811 100812 100813 100814 100815 100816 100817 100818 100819 100820 100821 100822 100823 100824 100825 100826 100827 100828 100829 100830 100831 100832 100833 110000 110001 110002 100738 100739 100740 100741 100742 100743 100744 100745 100746 100747 100748 100749 100750 100751 100752 100753 100754 100755 100756 100757 100758 100759 100760 100761 100762 100763 100764 100765 100766 100767 100768 100769 100770 100771 100772 100773 100774 100775 100776 100777 100778 100779 100780 100781 100782 100783 100784 100785 100786 100787 100788 100789 100790 100791 100792 100793 100794 100795 100796 100797 100798 Foam System, Hale, FoamLogix 5.0, Single System, Class B Foam, Flush System Foam System, Hale, FoamLogix 5.0, Dual System, Manual Selector, Class A and B Foam, Flush System Foam System, Around the Pump, Feecon, APH 1.5, Class A, Flush System Foam System, Around the Pump, Feecon, APH 1.5, Class B, Flush System Foam System, Around the Pump, Williams, ATP 1500, Class B, Single Flush System, Charlotte Setup Foam System, Eductor, Akron, 3096 Bypass, 95 GPM, Class A, Flush System Foam System, Eductor, Akron, 3096 Bypass, 95 GPM, Class B, Flush System Foam System, Eductor, Akron, 3126 Bypass, 125 GPM, Class A, Flush System Foam System, Eductor, Akron, 3126 Bypass, 125 GPM, Class B, Flush System Foam System, Eductor, Elkhart, 240-95 Bypass, 95 GPM, Class A, Flush System Foam System, Eductor, Elkhart, 240-95 Bypass, 95 GPM, Class B, Flush System Foam System, Eductor, Elkhart, 240-125 Bypass, 125 GPM, Class A, Flush System Foam System, Eductor, Elkhart, 240-125 Bypass, 125 GPM, Class B, Flush System CAFS, Midship, Waterous, Eclipse, 200 CFM, Advantus 6 Single System, Class A CAFS, Midship, Waterous, Eclipse, 200 CFM, Advantus 6 Single System, Class A and B, Flush System CAFS, Midship, Waterous, Eclipse, 200 CFM, FoamPro 2002 Single System, Class A CAFS, PTO, Waterous, 140-P, 140 CFM, Aquis 2.5 Single System, Class A CAFS, PTO, Waterous, 140-P, 140 CFM, Advantus 6 Single System, Class A CAFS, PTO, Waterous, 140-P, 140 CFM, FoamPro 2001 Single System, Class A CAFS, PTO, Waterous, 140-P, 140 CFM, FoamPro 2002 Single System, Class A CAFS, PTO, Waterous, 200-P, 200 CFM, Advantus 6 Single System, Class A Engineered for Future Foam - Space on Panel - FoamPro 1600 Foam System Engineered for Future Foam - Space on Panel - FoamPro 2001/FoamPro 2002 Foam System Engineered for Future Foam - Space on Panel - Advantus 3/Advantus 6 Foam System Background Plate, Yellow, Charlotte Setup Booster Reel, Hannay, Aluminum, Polished, Electric Rewind, 100' of 3/4" Hose Capacity Booster Reel, Hannay, Aluminum, Polished, Electric Rewind, 100' of 1" Hose Capacity Booster Reel, Hannay, Aluminum, Polished, Electric Rewind, 150' of 3/4" Hose Capacity Booster Reel, Hannay, Aluminum, Polished, Electric Rewind, 150' of 1" Hose Capacity Booster Reel, Hannay, Aluminum, Polished, Electric Rewind, 200' of 3/4" Hose Capacity Booster Reel, Hannay, Aluminum, Polished, Electric Rewind, 200' of 1" Hose Capacity Booster Reel, Hannay, Steel, Stainless, Electric Rewind, 100' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Stainless, Electric Rewind, 100' of 1" Hose Capacity Booster Reel, Hannay, Steel, Stainless, Electric Rewind, 150' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Stainless, Electric Rewind, 150' of 1" Hose Capacity Booster Reel, Hannay, Steel, Stainless, Electric Rewind, 200' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Stainless, Electric Rewind, 200' of 1" Hose Capacity Booster Reel, Hannay, Steel, Hannay Red, Electric Rewind, 100' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Hannay Red, Electric Rewind, 100' of 1" Hose Capacity Booster Reel, Hannay, Steel, Hannay Red, Electric Rewind, 150' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Hannay Red, Electric Rewind, 150' of 1" Hose Capacity Booster Reel, Hannay, Steel, Hannay Red, Electric Rewind, 200' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Hannay Red, Electric Rewind, 200' of 1" Hose Capacity Booster Reel, Hannay, Steel, Hannay Silver, Electric Rewind, 100' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Hannay Silver, Electric Rewind, 100' of 1" Hose Capacity Booster Reel, Hannay, Steel, Hannay Silver, Electric Rewind, 150' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Hannay Silver, Electric Rewind, 150' of 1" Hose Capacity Booster Reel, Hannay, Steel, Hannay Silver, Electric Rewind, 200' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Hannay Silver, Electric Rewind, 200' of 1" Hose Capacity Booster Reel, Hannay, Steel, Painted Primary Body Color, Electric Rewind, 100' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Painted Primary Body Color, Electric Rewind, 100' of 1" Hose Capacity Booster Reel, Hannay, Steel, Painted Primary Body Color, Electric Rewind, 150' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Painted Primary Body Color, Electric Rewind, 150' of 1" Hose Capacity Booster Reel, Hannay, Steel, Painted Primary Body Color, Electric Rewind, 200' of 3/4" Hose Capacity Booster Reel, Hannay, Steel, Painted Primary Body Color, Electric Rewind, 200' of 1" Hose Capacity Booster Hose, 3/4", 800 lb Test, 50', (1) 50' Section Booster Hose, 3/4", 800 lb Test, 100', (1) 100' Section Booster Hose, 3/4", 800 lb Test, 100', (2) 50' Sections Booster Hose, 3/4", 800 lb Test, 150', (1) 100' Section, (1) 50' Section Booster Hose, 3/4", 800 lb Test, 150', (3) 50' Sections Booster Hose, 3/4", 800 lb Test, 200', (1) 200' Section Booster Hose, 3/4", 800 lb Test, 200', (1) 100' Sections, (2) 50' Sections Booster Hose, 3/4", 800 lb Test, 200', (2) 100' Sections Booster Hose, 3/4", 800 lb Test, 200', (4) 50' Sections Booster Hose, 1", 800 lb Test, 50', (1) 50' Section Booster Hose, 1", 800 lb Test, 100', (1) 100' Section Booster Hose, 1", 800 lb Test, 100', (2) 50' Sections Booster Hose, 1", 800 lb Test, 150', (1) 100' Section, (1) 50' Section Booster Hose, 1", 800 lb Test, 150', (3) 50' Sections Booster Hose, 1", 800 lb Test, 200', (1) 200' Section Booster Hose, 1", 800 lb Test, 200', (1) 100' Sections, (2) 50' Sections Booster Hose, 1", 800 lb Test, 200', (2) 100' Sections Booster Hose, 1", 800 lb Test, 200', (4) 50' Sections Booster Hose, 3/4", Niedner Reeltex, 100', (1) 100' Section Booster Hose, 3/4", Niedner Reeltex, 100', (2) 50' Section Booster Hose, 1", Niedner Reeltex, 50', (1) 50' Section Booster Hose, 1", Niedner Reeltex, 100', (1) 100' Section Booster Hose, 1", Niedner Reeltex, 100', (2) 50' Section Booster Hose, 1", Niedner Reeltex, 150', (1) 100' Section, (1) 50' Section Booster Hose, 1", Niedner Reeltex, 150', (3) 50' Section Booster Hose, 1", Niedner Reeltex, 200', (2) 100' Sections Booster Hose, 1", Niedner Reeltex, 200', (4) 50' Sections Booster Reel Location, Front Bumper, Center Booster Reel Location, Below Extended Cab, In Compartment, Driver's Side, Access Panel Prvd Booster Reel Location, Below Rear Cab Crew Door, In Compartment, Driver's Side, Access Panel Prvd Booster Reel Location, Below Extended Cab, In Compartment, Officer's Side, Access Panel Prvd Booster Reel Location, Below Rear Cab Crew Door, In Compartment, Officer's Side, Access Panel Prvd Booster Reel Location, Rear, Above EHL Booster Reel Location, Rear, Between the Frame Rails Rewind Switch, Booster Reel, Driver's Side Pump Panel Rewind Switch, Booster Reel, Officer's Side Pump Panel Rewind Switch, Booster Reel, On Rear of Body Rewind Switches, Booster Reel, (1) Driver's Side Pump Panel, (1) Foot Switch Below Running Board Rewind Switches, Booster Reel, (1) Officer's Side Pump Panel, (1) Foot Switch Below Running Board Deck Gun, Electric, Elkhart Cobra EXM 7200, 3" NPT Inlet, Panel and Wireless Controls Deck Gun, Electric, Elkhart Cobra EXM 7200, 3" FBF Inlet, Panel and Wireless Controls Storage Well, Front Bumper, Driver's Side, Tread Plate Cover with Notch Storage Well, Front Bumper, Driver's Side, Tread Plate Cover (NO Notch) Storage Well, Front Bumper, Driver's Side, Vinyl Cover, Black

110068 110069 110070 110071 110072 110073 110075 110077 110079 110080 110081 110082 110083 110084 110085 110086 110087 110088 110090 110092 110094 110095 110096 110097 110098 110099 110100 110101 110103 110105 110108 110109 110110 110111 110112 110113 110114 110115 110003 110004 110005 110006 110007 110008 110009 110010 110011 110012 110013 110014 110015 110016 110017 110018 110019 110020 110021 110022 110023 110024 110025 110026 110027 110028 110029 110030 110031 110032 110033 110034 110035 110036 110037 110038 110039 110040 110041 110042 110043 110044 110045 110046 110047 110048 110049 110050 110051 110052 110053 110054 110055 110056 110057 110058 110060 110063 110065 110066 110067 Storage Well, Front Bumper, Driver's Side, Vinyl Cover, Red Storage Well, Front Bumper, Driver's Side, PAC Straps Storage Well, Front Bumper, Center, Tread Plate Cover with Notch Storage Well, Front Bumper, Center, Tread Plate Cover (NO Notch) Storage Well, Front Bumper, Center, Vinyl Cover, Black Storage Well, Front Bumper, Center, Vinyl Cover, Red Storage Well, Front Bumper, Center, PAC Straps Storage Well, Front Bumper, Full Width, Headlight-to-Headlight, Full Tread Plate Raised Cover Storage Well, Front Bumper, Officer's Side, Tread Plate Cover with Notch Storage Well, Front Bumper, Officer's Side, Tread Plate Cover (NO Notch) Storage Well, Front Bumper, Officer's Side, Vinyl Cover, Black Storage Well, Front Bumper, Officer's Side, Vinyl Cover, Red Storage Well, Front Bumper, Officer's Side, PAC Straps Turnout Hooks, (2), In Cab, Rear Wall Turnout Hooks, (3), In Cab, Rear Wall Turnout Hooks, (4), In Cab, Rear Wall Mounting Plate, On Engine Tunnel, Aluminum, Line-X, Black Mounting Plate, On Engine Tunnel, Aluminum, Line-X, Gray Mounting Plate, On Engine Tunnel, Aluminum, MultiSpec, Gray Mounting Plate, On Engine Tunnel, Aluminum, MultiSpec, Onyx Mounting Plate, On Engine Tunnel, Aluminum, MultiSpec, Red SCBA Seat Bracket, (1), Zico Load and Lock SCBA Seat Brackets, (2), Zico Load and Lock SCBA Seat Brackets, (3), Zico Load and Lock SCBA Seat Brackets, (4), Zico Load and Lock SCBA Seat Brackets, (5), Zico Load and Lock Helmet Brackets, (3), On-Scene Talon Helmet Brackets, (4), On-Scene Talon Helmet Brackets, (5), On-Scene Talon Helmet Brackets, (6), On-Scene Talon Helmet Brackets, (3), Zico Helmet Brackets, (4), Zico Helmet Brackets, (5), Zico Helmet Brackets, (6), Zico Helmet Brackets, (3), Chassis Supplied, OEM Installed Helmet Brackets, (4), Chassis Supplied, OEM Installed Helmet Brackets, (5), Chassis Supplied, OEM Installed Helmet Brackets, (6), Chassis Supplied, OEM Installed Helmet Brackets, (3), Customer Supplied, OEM Installed Helmet Brackets, (4), Customer Supplied, OEM Installed Helmet Brackets, (5), Customer Supplied, OEM Installed Helmet Brackets, (6), Customer Supplied, OEM Installed Receptacle, 120V, 5-15R Household, Duplex, Wired to Shoreline Receptacle, 120V, 5-15R Household, Duplex, Wired to Generator Receptacle, 120V, 5-15R Household, Duplex, Wired to Transfer Switch Receptacle, 120V, L5-15R Twistlock, Duplex, Wired to Shoreline Receptacle, 120V, L5-15R Twistlock, Duplex, Wired to Generator Receptacle, 120V, L5-15R Twistlock, Duplex, Wired to Transfer Switch Receptacle, 120V, 5-20R Straight Blade, Duplex, Wired to Generator Receptacle, 120V, 5-20R Straight Blade, Duplex, Wired to Transfer Switch Receptacle, 120V, L5-15R Twistlock, Single, Wired to Shoreline Receptacle, 120V, L5-15R Twistlock, Single, Wired to Generator Receptacle, 120V, L5-15R Twistlock, Single, Wired to Transfer Switch Receptacle, 120V, L5-20R Twistlock, Single, Wired to Shoreline Receptacle, 120V, L5-20R Twistlock, Single, Wired to Generator Receptacle, 120V, L5-20R Twistlock, Single, Wired to Transfer Switch Receptacle, 240V, L6-20R Twistlock, Single, Wired to Generator Receptacle, 240V, L6-30R Twistlock, Single, Wired to Generator Outlet Bar, 120V, (6) Receptacles, 5-15R Household, Wired to Transfer Switch Cab Electrical, Non-Multiplex, Integrate with Multiplex Body, Diamondlogic OEM Chassis Preparations, Other Auxiliary Engine Cooler, Chassis Supplied and Installed Chassis Step Lights, LED, Grote, 2 Door Chassis Step Lights, LED, Grote, 4 Door Chassis Step Lights, LED, Whelen, 2 Door Chassis Step Lights, LED, Whelen, 4 Door Water Tank, Pro-Poly, 400 U.S. Gallons Water Tank, Pro-Poly, 500 U.S. Gallons Water Tank, Pro-Poly, 750 U.S. Gallons Water Tank, Pro-Poly, 1000 U.S. Gallons Water Tank, Pro-Poly, 1250 U.S. Gallons Water Tank, Pro-Poly, 1500 U.S. Gallons Water Tank, Pro-Poly, 1800 U.S. Gallons Water Tank, Pro-Poly, 2000 U.S. Gallons Water Tank, Pro-Poly, 2500 U.S. Gallons Water Tank, Pro-Poly, 3000 U.S. Gallons Water Tank, Pro-Poly, 250 Imperial Gallons Water Tank, Pro-Poly, 300 Imperial Gallons Water Tank, Pro-Poly, 400 Imperial Gallons Water Tank, Pro-Poly, 500 Imperial Gallons Water Tank, Pro-Poly, 600 Imperial Gallons Water Tank, Pro-Poly, 800 Imperial Gallons Water Tank, Pro-Poly, 1000 Imperial Gallons Water Tank, Pro-Poly, 1250 Imperial Gallons Water Tank, Pro-Poly, 1600 Imperial Gallons Water Tank, Pro-Poly, 2000 Imperial Gallons Water Tank, Pro-Poly, 2500 Imperial Gallons Water Tank, UPF, 300 U.S. Gallons Water Tank, UPF, 400 U.S. Gallons Water Tank, UPF, 500 U.S. Gallons Water Tank, UPF, 750 U.S. Gallons Water Tank, UPF, 1000 U.S. Gallons Water Tank, UPF, 1250 U.S. Gallons Water Tank, UPF, 1500 U.S. Gallons Water Tank, UPF, 1800 U.S. Gallons Water Tank, UPF, 2000 U.S. Gallons Water Tank, UPF, 2500 U.S. Gallons Water Tank, UPF, 3000 U.S. Gallons Water Tank, UPF, 250 Imperial Gallons

110180 110181 110182 110183 110184 110185 110186 110187 110188 110189 110190 110191 110192 110193 110194 110195 110196 110197 110198 110199 110200 110201 110202 110203 110204 110205 110206 110207 110208 110209 110210 110211 110212 110213 110214 110215 110216 110217 110116 110117 110119 110121 110123 110124 110125 110126 110127 110128 110129 110130 110131 110132 110133 110134 110135 110136 110137 110138 110139 110140 110141 110142 110143 110144 110145 110146 110147 110148 110149 110150 110151 110152 110153 110154 110155 110156 110157 110158 110159 110160 110161 110162 110163 110164 110165 110166 110167 110168 110169 110170 110171 110172 110173 110174 110175 110176 110177 110178 110179 Water Tank, UPF, 300 Imperial Gallons Water Tank, UPF, 400 Imperial Gallons Water Tank, UPF, 500 Imperial Gallons Water Tank, UPF, 600 Imperial Gallons Water Tank, UPF, 800 Imperial Gallons Water Tank, UPF, 1000 Imperial Gallons Water Tank, UPF, 1250 Imperial Gallons Water Tank, UPF, 1600 Imperial Gallons Water Tank, UPF, 2000 Imperial Gallons Water Tank, UPF, 2500 Imperial Gallons Hose Bed, Aluminum, Standard, Abraded Finish Hose Bed, Aluminum, Standard, Black Line-X Finish Hose Bed, Aluminum, Standard, Painted Primary Body Color Finish Hose Bed, Aluminum, Low, Abraded Finish Hose Bed, Aluminum, Low, Black Line-X Finish Hose Bed, Aluminum, Low, Painted Primary Body Color Finish Hose Bed, Stainless Steel, Standard, Black Line-X Finish Hose Bed, Stainless Steel, Standard, Brushed Stainless Finish Hose Bed, Stainless Steel, Standard, Painted Primary Body Color Finish Hose Bed, Stainless Steel, Low, Black Line-X Finish Hose Bed, Stainless Steel, Low, Brushed Stainless Finish Hose Bed, Stainless Steel, Low, Painted Primary Body Color Finish Hose Bed Rear Restraint, Vinyl, Top C-Rail, Bottom Bungee, Black Hose Bed Rear Restraint, Vinyl, Top C-Rail, Bottom Bungee, Red Hose Bed Rear Restraint, Vinyl, Top C-Rail, Bottom Footman Loop / J-Hook, Black Hose Bed Rear Restraint, Vinyl, Top C-Rail, Bottom Footman Loop / J-Hook, Red Hose Bed Door Rear Restraint, Webbing, 2" Divider, Horizontal, Split Hose, (1), Finish to Match Main Divider Divider, Horizontal, Split Hose, (2), Finish to Match Main Dividers Divider, Horizontal, Split Hose, (3), Finish to Match Main Dividers Divider, Horizontal, Split Hose, (4), Finish to Match Main Dividers Storage Partitions, (2), Adjustable, Aluminum, Abraded Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Bungee, Rear Bungee, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Bungee, Rear Footman Loop / J-Hook, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Button Snaps, Rear Bungee, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Button Snaps, Rear Footman Loop / J-Hook, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Quarter-Turns, Rear Bungee, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Quarter-Turns, Rear Footman Loop / J-Hook, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Velcro, Rear Bungee, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Velcro, Rear Footman Loop / J-Hook, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Bungee, Rear Bungee, Red Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Bungee, Rear Footman Loop / J-Hook, Red Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Button Snaps, Rear Bungee, Red Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Button Snaps, Rear Footman Loop / J-Hook, Red Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Quarter-Turns, Rear Bungee, Red Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Quarter-Turns, Rear Footman Loop / J-Hook, Red Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Velcro, Rear Bungee, Red Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Velcro, Rear Footman Loop / J-Hook, Red Valve, 1-1/2", Elkhart, Manual, EB15-R1F, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel) Pump Module, Side Mount, Integral, CORE, Aluminum, 1/8" Pump Module, Side Mount, Integral, CORE, Aluminum, 3/16" Pump Module, Side Mount, Integral, CORE, Galvanneal Steel, 12 Gauge Pump Module, Side Mount, Integral, CORE, Stainless Steel, 304 Pump Module, Side Mount, Integral, CORE, Stainless Steel, 409 Pump Module, Side Mount, Integral, Rage, Galvanneal Steel, 12 Gauge Pump Module, Side Mount, Independent, 1/8" Aluminum Pump Module, Side Mount, Independent, 1/8" Aluminum, Enclosed Driver's Side Pump Panel Pump Module, Side Mount, Independent, 1/8" Aluminum, Enclosed Officer's Side Pump Panel Pump Module, Side Mount, Independent, 1/8" Aluminum, Enclosed Both Side Pump Panels Pump Module, Side Mount, Independent, 3/16" Aluminum Pump Module, Side Mount, Independent, 3/16" Aluminum, Enclosed Driver's Side Pump Panel Pump Module, Side Mount, Independent, 3/16" Aluminum, Enclosed Officer's Side Pump Panel Pump Module, Side Mount, Independent, 3/16" Aluminum, Enclosed Both Side Pump Panels Pump Module, Side Mount, Independent, 12 Gauge Galvanneal Steel Pump Module, Side Mount, Independent, 12 Gauge Galvanneal Steel, Enclosed Driver's Side Pump Panel Pump Module, Side Mount, Independent, 12 Gauge Galvanneal Steel, Enclosed Officer's Side Pump Panel Pump Module, Side Mount, Independent, 12 Gauge Galvanneal Steel, Enclosed Both Side Pump Panels Pump Module, Side Mount, Independent, 304 Stainless Steel Pump Module, Side Mount, Independent, 304 Stainless Steel, Enclosed Driver's Side Pump Panel Pump Module, Side Mount, Independent, 304 Stainless Steel, Enclosed Officer's Side Pump Panel Pump Module, Side Mount, Independent, 304 Stainless Steel, Enclosed Both Side Pump Panels Pump Module, Side Mount, Independent, 409 Stainless Steel Pump Module, Side Mount, Independent, 409 Stainless Steel, Enclosed Driver's Side Pump Panel Pump Module, Side Mount, Independent, 409 Stainless Steel, Enclosed Officer's Side Pump Panel Pump Module, Side Mount, Independent, 409 Stainless Steel, Enclosed Both Side Pump Panels Pump Module, Top Mount, Independent, 1/8" Aluminum Pump Module, Top Mount, Independent, 1/8" Aluminum, Enclosed Pump Panel Pump Module, Top Mount, Independent, 3/16" Aluminum Pump Module, Top Mount, Independent, 3/16" Aluminum, Enclosed Pump Panel Pump Module, Top Mount, Independent, 12 Gauge Galvanneal Steel Pump Module, Top Mount, Independent, 12 Gauge Galvanneal Steel, Enclosed Pump Panel Pump Module, Top Mount, Independent, 304 Stainless Steel Pump Module, Top Mount, Independent, 304 Stainless Steel, Enclosed Pump Panel Pump Module, Top Mount, Independent, 409 Stainless Steel Pump Module, Top Mount, Independent, 409 Stainless Steel, Enclosed Pump Panel Engineers Compartments, Lap Doors, On-Scene Access LED, No Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, On-Scene Access LED, No Shelf, No Tiles Engineers Compartments, Lap Doors, On-Scene Access LED, No Shelf, Turtle Tiles Engineers Compartments, Lap Doors, On-Scene Access LED, (1) Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, On-Scene Access LED, (1) Shelf, No Tiles Engineers Compartments, Lap Doors, On-Scene Access LED, (1) Shelf, Turtle Tiles Engineers Compartments, Lap Doors, On-Scene Night Axe LED, No Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, On-Scene Night Axe LED, No Shelf, No Tiles Engineers Compartments, Lap Doors, On-Scene Night Axe LED, No Shelf, Turtle Tiles Engineers Compartments, Lap Doors, On-Scene Night Axe LED, (1) Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, On-Scene Night Axe LED, (1) Shelf, No Tiles Engineers Compartments, Lap Doors, On-Scene Night Axe LED, (1) Shelf, Turtle Tiles Insulation/Ventilation, Pump Compartment Interior - Rubber Seals, Pump Module / Intakes / Discharges Enclosed Pump Panel Door, (1) Hansen Roll-Up Door Construction, Painted Door Only

110282 110283 110284 110285 110286 110287 110288 110289 110290 110291 110292 110293 110294 110295 110296 110297 110298 110299 110300 110301 110302 110303 110304 110305 110306 110307 110308 110309 110310 110311 110312 110313 110314 110315 110316 110317 110318 110319 110218 110219 110220 110221 110222 110223 110224 110225 110226 110227 110229 110230 110231 110232 110233 110234 110235 110236 110237 110238 110239 110240 110241 110242 110243 110244 110245 110246 110247 110248 110249 110250 110251 110252 110253 110254 110255 110256 110257 110258 110259 110260 110261 110262 110263 110264 110265 110266 110267 110268 110270 110272 110273 110274 110275 110276 110277 110278 110279 110280 110281 Pump Panel Lighting, Enclosed Side (2) Hansen 10MM White LED Lights, Exposed Side On-Scene Night Axe LED Enclosed Pump Panel Door, (1) Hansen Roll-Up Door Construction, Painted Door, Sills, and Tracks Pump Panel Lighting, Enclosed Sides (4) Hansen 6MM White LED Lights Enclosed Pump Panels Doors, (2) Hansen Roll-Up Door Construction, Painted Door Only Pump Panels, Side Mount, Controls on Driver's Side, Black Line-X Finish, IC Bezels/Trim Rings/Labels Enclosed Pump Panels Doors, (2) Hansen Roll-Up Door Construction, Painted Door, Sills, and Tracks Pump Panels, Side Mount, Controls on Driver's Side, Stainless Steel Panels, IC Bezels/Trim Rings/Labels, Rage Pump Panels, Side Mount, Controls on Driver's Side, Stainless Steel Panels, IC Bezels/Trim Rings/Labels Pump Panels, CORE, OMNI System, Removable Display, L1 and R3 Mounts, IC Bezels/Trim Rings/Labels Pump Panels, Side Mount, Controls on Driver's Side, IC Diagrammatic Overlay, Painted Aluminum Panels Pump Panels, Top Mount, Black Line-X Finish, IC Bezels/Trim Rings/Labels Pump Panels, Top Mount, Stainless Steel Panels, IC Bezels/Trim Rings/Labels Access Panel, Pump, Driver's Side, Stainless Steel with Compression Latches Access Panel, Pump, Officer's Side, Stainless Steel with Compression Latches Walkway, Center, Top Mount, 24", LED Lighting Walkway, Center, Top Mount, 24", LED Lighting, Mansaver Bars, Yellow Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Lift-A-Dot, Rear Bungee, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Lift-A-Dot, Rear Bungee, Red Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Lift-A-Dot, Rear Footman Loop / J-Hook, Black Hose Bed Cover, Vinyl, Top/Rear Single Piece, Side Lift-A-Dot, Rear Footman Loop / J-Hook, Red Speaker/Radio Compartment, Above Operator's Panel, Polished Stainless Door Speaker/Radio Compartment, Above Operator's Panel, Brushed Stainless Door Speaker/Radio Compartment, Above Operator's Panel, Painted Door Speaker/Radio Compartment, On Incline Panel Surface, Polished Stainless Door Speaker/Radio Compartment, On Incline Panel Surface, Brushed Stainless Door Speaker/Radio Compartment, On Incline Panel Surface, Painted Door Pump, Darley, Single-Stage (PTO), 1000 GPM, PSP Pump, Darley, Single-Stage (PTO), 1250 GPM, PSP Pump, Darley, Single-Stage (PTO), 1500 GPM, PSP Pump, Darley, Single-Stage, 1000 GPM, PSM, MagnaTrans Transmission Pump, Darley, Single-Stage, 1250 GPM, PSM, MagnaTrans Transmission Pump, Darley, Single-Stage, 1500 GPM, PSM, MagnaTrans Transmission Pump, Hale, Single-Stage (PTO), 1250 GPM, RSD-J Pump, Hale, Single-Stage, 1250 GPM, DSD, G-Series Pump, Hale, Single-Stage, 1500 GPM, DSD, G-Series Pump, Hale, Single-Stage, 2250 GPM, 8FG, G-Series Pump, Hale, Single-Stage, 2250 GPM, 8FG, K-Series Pump, Waterous, Single-Stage (PTO), 1000 GPM, CSPA, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage (PTO), 1000 GPM, CSPA, Standard Impellers Pump, Waterous, Single-Stage (PTO), 1250 GPM, CSPA, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage (PTO), 1250 GPM, CSPA, Standard Impellers Pump, Waterous, Single-Stage (PTO), 1500 GPM, CXSPA, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage (PTO), 1500 GPM, CXSPA, Standard Impellers Pump, Waterous, Single-Stage, 1000 GPM, CXVC20, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 1000 GPM, CXVC20, Standard Impellers Pump, Waterous, Single-Stage, 1250 GPM, CXVC20, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 1250 GPM, CXVC20, Standard Impellers Pump, Waterous, Single-Stage, 1500 GPM, CXSC20, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 1500 GPM, CXSC20, Standard Impellers Pump, Waterous, Single-Stage, 2000 GPM, S100C20, Flame Plated Impeller Hubs Manifold, Waterous, CAFS Plug, Special Thread, 2-1/2", South Park Plug, Special Thread, 2-1/2", Trident Discharge, Front Bumper Center, 1-1/2", In Hosewell, NPSH Discharge, Front Bumper Center, 1-1/2", In Hosewell, NST Crosslay, Above Pump Panel, (1) 1-1/2" Crosslays, Above Pump Panel, (3) 1-1/2" Crosslays, Above Pump Panel, (3) 1-1/2" and (1) 2-1/2" Crosslays, Front Bumper, (2) 1-1/2" Crosslays, Rear Bumper, (2) 1-1/2" Speedlay Module, Ahead of Pump Panel, (2) 1-1/2" and (1) 2-1/2", With Lift Out Trays Speedlays in Lift Out Trays, Ahead of Pump Panel, (2) 1-1/2", Crosslay, Above Speedlays, (1) 2-1/2" Speedlays in Lift Out Trays, Enclosed with Pump Panel, (2) 1-1/2", Side-By-Side Speedlays in Lift Out Trays, Enclosed with Pump Panel, (3) 1-1/2" Additional Speedlay Tray, Abraded, (1) Additional Speedlay Trays, Abraded, (2) Additional Speedlay Trays, Abraded, (3) Additional Speedlay Trays, Abraded, (4) Crosslay End Covers, Vinyl, C-Rail Top and Bungee Bottom, Black Crosslay End Covers, Vinyl, C-Rail Top and Bungee Bottom, Red Crosslay End Covers, Vinyl, C-Rail Top and Footman Loop / J-Hook on Bottom, Black Crosslay End Covers, Vinyl, C-Rail Top and Footman Loop / J-Hook on Bottom, Red Speedlay End Cover, Vinyl, Bungee, 1 Cover on 1 Side, Black Speedlay End Cover, Vinyl, Bungee, 1 Cover on 1 Side, Red Speedlay End Cover, Vinyl, Footman Loop / J-Hook, 1 Cover on 1 Side, Black Speedlay End Cover, Vinyl, Footman Loop / J-Hook, 1 Cover on 1 Side, Red Speedlay End Covers, Vinyl, Bungee, 1 Cover on Each Side, Black Speedlay End Covers, Vinyl, Bungee, 1 Cover on Each Side, Red Speedlay End Covers, Vinyl, Bungee, 2 Covers on 1 Side, Black Speedlay End Covers, Vinyl, Bungee, 2 Covers on 1 Side, Red Speedlay End Covers, Vinyl, Bungee, 2 Covers on Each Side, Black Speedlay End Covers, Vinyl, Bungee, 2 Covers on Each Side, Red Speedlay End Covers, Vinyl, Footman Loop / J-Hook, 1 Cover on Each Side, Black Speedlay End Covers, Vinyl, Footman Loop / J-Hook, 1 Cover on Each Side, Red Speedlay End Covers, Vinyl, Footman Loop / J-Hook, 2 Covers on 1 Side, Black Speedlay End Covers, Vinyl, Footman Loop / J-Hook, 2 Covers on 1 Side, Red Speedlay End Covers, Vinyl, Footman Loop / J-Hook, 2 Covers on Each Side, Black Speedlay End Covers, Vinyl, Footman Loop / J-Hook, 2 Covers on Each Side, Red Crosslay Top / End Cover, Vinyl, C-Rail and Velcro Top and Bungee on Bottom, Black Crosslay Top / End Cover, Vinyl, C-Rail and Velcro Top and Bungee on Bottom, Red Crosslay Top / End Cover, Vinyl, C-Rail and Velcro Top and Footman Loop and J-Hook on Bottom, Black Crosslay Top / End Cover, Vinyl, C-Rail and Velcro Top and Footman Loop and J-Hook on Bottom, Red Deck Gun, Electric, Akron Deck Master 3440, 3" NPT Inlet, 30' Tether Controller in L1 Deck Gun, Electric, Akron Deck Master 3440, 3" NPT Inlet, 30' Tether in L1 and Wireless Controls Deck Gun, Electric, Akron Deck Master 3440, 3" NPT Inlet, Flush Panel Mount and Wireless Controls Deck Gun, Electric, Akron Deck Master 3440, 3" NPT Inlet, Flush Panel Mount Controller Deck Gun, Electric, TFT Typhoon Y5-E61A, 3" NPT Inlet, 30' Tether Controller in L1 Deck Gun, Electric, TFT Typhoon Y5-E61A, 3" NPT Inlet, 30' Tether in L1 and Wireless Controls Deck Gun, Electric, TFT Typhoon Y5-E61A, 3" NPT Inlet, Panel Mount and Wireless Controls

110381 110382 110383 110384 110385 110386 110387 110388 110389 110390 110391 110392 110393 110394 110395 110396 110397 110398 110399 110400 110402 110404 110406 110409 110412 110413 110419 110466 110467 110469 110472 110473 110475 110479 110486 110487 110489 110493 110320 110321 110322 110323 110324 110325 110326 110327 110328 110329 110330 110331 110332 110333 110334 110335 110336 110337 110338 110339 110340 110341 110342 110343 110344 110345 110346 110347 110348 110349 110350 110351 110352 110353 110354 110355 110356 110357 110358 110359 110360 110361 110362 110363 110364 110365 110366 110367 110368 110369 110370 110371 110372 110373 110374 110375 110376 110377 110378 110379 110380 Deck Gun, Electric, TFT Typhoon Y5-E61A, 3" NPT Inlet, Panel Mount Controller Deck Gun, Manual, Akron Apollo 3423, 3" NPT Inlet, Dual Inlet Ground Base, NST Inlet Thread Deck Gun, Manual, Akron Apollo 3423, 3" NPT Inlet, Dual Inlet Ground Base, Special Inlet Thread Preconnect, Bulkhead Fitting (Driver's Side), Crosslay/Speedlay, 1-1/2", NPSH Preconnect, Bulkhead Fitting (Driver's Side), Crosslay/Speedlay, 1-1/2", NST Preconnect, Bulkhead Fitting (Driver's Side), Crosslay/Speedlay, 2-1/2", NST Preconnect, Bulkhead Fitting (Officer's Side), Crosslay/Speedlay, 1-1/2", NPSH Preconnect, Bulkhead Fitting (Officer's Side), Crosslay/Speedlay, 1-1/2", NST Preconnect, Bulkhead Fitting (Officer's Side), Crosslay/Speedlay, 2-1/2", NST Auxiliary Pump, Waterous CPK2, Harrison IHT Driven Dedicated Discharge, Booster Reel Dedicated Discharge, Front Bumper Center, 1-1/2", In Hosewell, NPSH Dedicated Discharge, Front Bumper Center, 1-1/2", In Hosewell, NST Dedicated Discharge, Front Bumper Driver-Side, 1-1/2", Above Gravelshield, NPSH Dedicated Discharge, Front Bumper Driver-Side, 1-1/2", Above Gravelshield, NPSH, Controlled at Bumper Dedicated Discharge, Front Bumper Driver-Side, 1-1/2", Above Gravelshield, NST Dedicated Discharge, Front Bumper Driver-Side, 1-1/2", Above Gravelshield, NST, Controlled at Bumper Dedicated Discharge, Front Bumper Driver-Side, 1-1/2", In Hosewell, NPSH Dedicated Discharge, Front Bumper Driver-Side, 1-1/2", In Hosewell, NST Dedicated Discharge, Front Bumper Officer-Side, 1-1/2", Above Gravelshield, NPSH Dedicated Discharge, Front Bumper Officer-Side, 1-1/2", Above Gravelshield, NST Dedicated Discharge, Front Bumper Officer-Side, 1-1/2", In Hosewell, NPSH Dedicated Discharge, Front Bumper Officer-Side, 1-1/2", In Hosewell, NST Tank to Pump, 2-1/2", Akron 8800 2-1/2" Manual Valve, IC Push-Pull Handle Tank to Pump, 2-1/2", Akron 8800 2-1/2" Manual Valve, IC Top Mount Handle Tank to Pump, 2-1/2", Akron 8900 2-1/2" Manual Valve, IC Push-Pull Handle Tank to Pump, 2-1/2", Akron 8900 2-1/2" Manual Valve, IC Top Mount Handle Tank to Pump, 2-1/2", Elkhart 2-1/2" Manual Valve, IC Push-Pull Handle Tank to Pump, 2-1/2", Elkhart 2-1/2" Manual Valve, IC Top Mount Handle Tank to Pump, 2-1/2", Akron 8600 2-1/2" Electric Valve, 9323 Controller Tank to Pump, 2-1/2", Elkhart 2-1/2" Electric Valve, UBEC1 Controller Instrument Panel with Vernier Throttle, at Pump Panel, Hale HPX Instrument Panel and Throttle, at Pump Panel, Waterous CPK-2 Priming System, Trident RPV Cooling Line, 1/2" In-Cab Instrument Panel, Start/Stop, Vernier Throttle, Hale HPX In-Cab Instrument Panel, Start/Stop, Throttle, OEM Supplied/Installed Primer in Cab, Trident RPV Access Panel, Officer Side, Painted, Bolt-On Access Panel, Officer Side, Painted, Bolt-On, With Cooling Fan Ground Lights, LED, Amdor Lumabar, 20", Activation by Park Brake Ground Lights, LED, Amdor Lumabar, 20", Activation by Park Brake and Reverse Ground Lights, LED, Grote, Activation by Park Brake Ground Lights, LED, Grote, Activation by Park Brake and Reverse Ground Lights, LED, On Scene Night Axe, 9", Activation by Park Brake Ground Lights, LED, On Scene Night Axe, 9", Activation by Park Brake and Reverse Ground Lights, LED, Truck-Lite Model 44, Activation by Park Brake Ground Lights, LED, Truck-Lite Model 44, Activation by Park Brake and Reverse Ground Lights, LED, Whelen, Activation by Park Brake Ground Lights, LED, Whelen, Activation by Park Brake and Reverse Parking Lights, Rear Fender Wells, LED, Tecniq E96 Hose Bed Loading Lights, (4) Total, (2) Front of Hose Bed, (1) Each Side, LED, Grote Hose Bed Loading Lights, (2) Rear, LED, Whelen, Micro MPBW Hose Bed Loading Lights, (6) Total, (3) Each Side, On-Scene, Night Axe LED, 9" Hose Bed Loading Lights, (6) Total, (3) Each Side, On-Scene, Night Axe LED, 27" Receiver Tube, (1), Rear, Class III Tow Hitch, 7 Pin Receptacle Receiver Tube, (1), Rear, Class III Tow Hitch, With Brake Controller, 7 Pin Receptacle Receiver Tube, (1), Rear, Class IV Tow Hitch, With Brake Controller, 7 Pin Receptacle Camera System, Back-Up, Chassis Supplied, OEM Installed, OEM Provided 2nd Monitor on Pump Panel Rear-Step Buzzer System, With Remote Control Radio Interface Cable, David Clark, Harris Radio Interface Cable, Firecom, Harris Radio Interface Cable, Sigtronics, Harris Radio Interface Cable, David Clark, M/A COM Radio Interface Cable, Firecom, M/A COM Radio Interface Cable, Sigtronics, M/A COM Generator, Hydraulic, Harrison, 6kw, MDS, IHT Ready For Waterous CPK2, FRC Frog Display Cut-Off Switch, Generator, In Cab Upper Zone A, Lightbar, Federal Signal, 72", Aerodynic, ADX7250 Upper Zone A, Lightbar, Power Arc, 85" Volt, VM8504-6P Upper Zone A, Lightbar, Whelen, 55", Freedom LED, Flat Roof, 3 Red, 2 White, 3 Blue Upper Zone A, Lightbar, Whelen, 55", Freedom LED, Raised Roof, 6 Red, 2 White Upper Zone A, Lightbar, Whelen, 72", Freedom LED, Flat Roof, 10 Red, 2 White, 2 Alley Upper Zone A, Lightbar, Whelen, 72", Freedom LED, Flat Roof, 6 Red, 2 White, 6 Blue Upper Zone A, Lightbar, Whelen, 72", Freedom LED, Raised Roof, 3 Red, 2 White, 3 Blue Upper Zone A, Lightbar, Whelen, 72", Freedom LED, Raised Roof, 6 Red, 2 White, 2 Blue Upper Zone A, Lightbar, Whelen, 72", Freedom ROTA-BEAM LED, 7 Red, 2 White (Fully Populated Front) Upper Zone A, Lightbar, Whelen, 72", Freedom ROTA-BEAM LED, 7 Red, 2 White (Fully Populated Front), Quick Disconnects Upper Zone A, Lightbar, Whelen, 93", Freedom ROTA-BEAM, With Opticom (Charlotte) Upper Zone A, Lightbars (2), Code 3, RMX, 18", Model RMX18NFPA1 Upper Zone C, Rotating Beacons (2), Code 3, Halogen 550F Upper Zone C, Rotating Beacons (2), Federal Signal, Halogen 100F Upper Zone C, Rotating Beacons (2), Federal Signal, IVP SLR Upper Zone C, Rotating Beacons (2), Whelen, RB6 Upper Zone C, Rotating Beacons (2), Whelen, L31 LED Upper Zone C, Rotating Beacons (2), Whelen, ROTA-BEAM R416 Series Upper Zone C, Rotating/Warning Beacons (2), Whelen, B6T LED Upper Zone C, Rotating/Warning Beacons (2), Whelen, B63M7 LED Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, Perimeter 3 x 7 Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, Perimeter 4 x 6 Lower Zone Warning Light Package, (4) OEM Sup., Federal Signal, LED, QuadraFlare 6 x 4 Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, 500 Series TIR6 Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, 600 Series Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, 600 Series Side-By-Side Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, 700 Series Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, LINZ6 Series Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, M6 Series Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, M6 Series Split Side-By-Side Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, M7 Series

110587 110588 110589 110590 110591 110592 110593 110594 110595 110596 110597 110598 110599 110600 110601 110602 110603 110604 110605 110606 110607 110608 110609 110610 110611 110612 110613 110614 110615 110616 110617 110618 110619 110620 110621 110622 110623 110624 110496 110499 110500 110502 110505 110506 110508 110512 110519 110520 110522 110526 110529 110535 110537 110540 110541 110542 110543 110544 110545 110546 110547 110548 110549 110550 110551 110552 110553 110554 110555 110556 110557 110558 110559 110560 110561 110563 110564 110565 110566 110567 110568 110569 110570 110571 110572 110573 110574 110575 110576 110577 110578 110579 110580 110581 110582 110583 110584 110585 110586 Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, 600 Series ROTA-BEAM Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, Perimeter 3 x 7 Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, Perimeter 4 x 6 Lower Zone Warning Light Package, (8) OEM Sup., Federal Signal, LED, QuadraFlare 6 x 4 Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, 500 Series TIR6 Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, 600 Series Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, 600 Series Side-By-Side Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, 700 Series Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, LINZ6 Series Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, M6 Series Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, M6 Series Split Side-By-Side Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, M7 Series Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, 600 Series ROTA-BEAM Warning Lights, Additional (2), Upper Zone C, Warning Lights (2), Whelen, LED, Micro Edge Series Warning Lights, Additional (2), Above Driver/Officer Doors, Whelen, FNMINI Lightbars Opticom, 795H Emitter, In Lightbar Opticom, 792H Emitter, Above Windshield Opticom, 792H Emitter, Below Windshield Traffic Advisor, Whelen, 6-Light, 5mm LED Low-Profile, TAL65, TACTLD1 Controller, Center Brake Light (Special) Traffic Advisor, Whelen, 6-Light, Dominator TIR3 LED, TAD6 LED, TACTLD1 Controller Traffic Advisor, Whelen, 8-Light, (Individual) TIR3 LED, RSA03ZCR, TACTLD1 Controller Traffic Advisor, Whelen, 8-Light, Front Load LED, TANF85-LED, TACTLD1 Controller Traffic Directional Light, Code 3, 5-Light, TriCore Narrowstik, NASLTC547, Standard Controller Traffic Directional Light, Code 3, 8-Light, LED X Narrowstik, NASL839, Standard Controller Traffic Directional Light, Federal Signal, 6-Light Latitude SignalMaster LED, SL6S-A, Standard Controller Traffic Directional Light, Federal Signal, 6-Light Latitude SignalMaster LED, SL6S-A, Deluxe Controller Traffic Directional Light, Federal Signal, 8-Light Latitude SignalMaster LED, SL8S-A, Standard Controller Traffic Directional Light, Federal Signal, 8-Light Latitude SignalMaster LED, SL8S-A, Deluxe Controller Traffic Flow Board, Command Light, 5 Series LED, TFB-V5, Wireless Panel Mount Controller Traffic Directional Light Location, Above Rear of Body, Mounted In Tread Plate Box Traffic Directional Light Location, Hose Bed Doors, Flush Mounted Traffic Directional Light Location, Hose Bed Doors, Recess Mounted Traffic Directional Light Location, Hose Bed Doors, Surface Mounted Light Tower Shield on Chassis, Tread Plate Search Light, Golight 2020, Pedestal Mount, (1) Remote Control Search Light, Golight 20204, Permanent Mount, (1) Remote Control Search Lights, (2) Golight 2020, Pedestal Mount, (2) Remote Controls Each Scene Light, (1), 12V, FRC, Brow Mount, LED Focus Evolution 15,000 Lumens Scene Light, (1), 12V, FRC, Lightbar Mount, LED Spectra 20,000 Lumens Scene Light, (1), 12V, FRC, Pedestal Mount, Halogen Focus 300W, Switch on Lighthead Scene Light, (1), 12V, FRC, Pedestal Mount, HID Optimum 150W, Switch on Lighthead Scene Light, (1), 12V, FRC, Pedestal Mount, LED Focus Evolution 15,000 Lumen, Switch on Lighthead Scene Light, (1), 12V, FRC, Pedestal Mount, LED Spectra 20,000 Lumen, Switch on Lighthead Scene Light, (1), 12V, FRC, Recessed, LED Focus Evolution 12,000 Lumens Scene Light, (1), 12V, Whelen, Lightbar Mount, LED Pioneer (PFA2) Floodlight Scene Light, (1), 12V, Whelen, Lightbar Mount, LED Pioneer Plus (PFP2) Floodlight Scene Light, (1), 12V, Whelen, Pedestal Mount, LED PAR 36 Floodlight, Black Housing, Switch on Lighthead Scene Light, (1), 12V, Whelen, Pedestal Mount, LED Pioneer (PFA1) Floodlight, Switch on Lighthead Scene Light, (1), 12V, Whelen, Pedestal Mount, LED Pioneer (PFA2) Floodlight, Switch on Lighthead Scene Light, (1), 12V, Whelen, Pedestal Mount, LED Pioneer Plus (PCP2) Combo Spot/Flood, Switch on Lighthead Scene Light, (1), 12V, Whelen, Pedestal Mount, LED Pioneer Plus (PFP1) Floodlight , Switch on Lighthead Scene Light, (1), 12V, Whelen, Pedestal Mount, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead Scene Light, (1), 12V, Whelen, Surface Mount, LED Pioneer (PCP2) Combo Spot/Flood Scene Light, (1), 12V, Whelen, Surface Mount, LED Pioneer Plus Max (PCP3) Combo Spot/Flood Scene Lights, Pair, 12V, Federal Signal, Surface Mount, GHS Dual-Head Scene Lights, Pair, 12V, FRC, Brow Mount, HID Focus 150W Scene Lights, Pair, 12V, FRC, Brow Mount, HID Optimum 150W Scene Lights, Pair, 12V, FRC, Brow Mount, LED Focus Evolution 15,000 Lumens Scene Lights, Pair, 12V, FRC, Brow Mount, LED Spectra 15,000 Lumen Scene Lights, Pair, 12V, FRC, Lightbar Mount, LED Spectra 20,000 Lumens Scene Lights, Pair, 12V, FRC, Pedestal Mount, Halogen Focus 300W, Switch on Lighthead Scene Lights, Pair, 12V, FRC, Pedestal Mount, HID Optimum 150W, Switch on Lighthead Scene Lights, Pair, 12V, FRC, Pedestal Mount, LED Focus Evolution 15,000 Lumen, Switch on Lighthead Scene Lights, Pair, 12V, FRC, Pedestal Mount, LED Spectra 20,000 Lumen, Switch on Lighthead Scene Lights, Pair, 12V, FRC, Recessed, Halogen Focus 150W Scene Lights, Pair, 12V, FRC, Recessed, Halogen Focus 300W Scene Lights, Pair, 12V, FRC, Recessed, HID Optimum 150W Scene Lights, Pair, 12V, FRC, Recessed, HID Optimum 70W Scene Lights, Pair, 12V, FRC, Recessed, LED Focus Evolution 12,000 Lumens Scene Lights, Pair, 12V, FRC, Surface Mount, LED Spectra 15,000 Lumen Scene Lights, Pair, 12V, FRC, Surface Mount, LED Spectra 900 4,600 Lumen Scene Lights, Pair, 12V, FRC, Telescoping Side Mount Pull-Up, LED Spectra 20,000 Lumen Scene Lights, Pair, 12V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 150W Scene Lights, Pair, 12V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 300W Scene Lights, Pair, 12V, FRC, Telescoping Side Mount Push-Up, HID Optimum 150W Scene Lights, Pair, 12V, FRC, Telescoping Side Mount Push-Up, LED Focus Evolution 15,000 Lumen Scene Lights, Pair, 12V, FRC, Telescoping Side Mount Push-Up, LED Spectra 20,000 Lumen Scene Lights, Pair, 12V, FRC, Telescoping Thru The Roof Push-Up, HID Optimum 150W Scene Lights, Pair, 12V, FRC, Telescoping Thru The Roof Push-Up, LED Spectra 20,000 Lumen Scene Lights, Pair, 12V, FRC, Telescoping Top Mount Pull-Up, HID Optimum 150W Scene Lights, Pair, 12V, FRC, Telescoping Top Mount Pull-Up, LED Spectra 20,000 Lumen Scene Lights, Pair, 12V, Whelen, Brow Mount, LED Pioneer (PFA1) Floodlight Scene Lights, Pair, 12V, Whelen, Brow Mount, LED Pioneer (PFA2) Floodlight Scene Lights, Pair, 12V, Whelen, Brow Mount, LED Pioneer Plus (PCP2) Combo Spot/Flood Scene Lights, Pair, 12V, Whelen, Brow Mount, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 12V, Whelen, Brow Mount, LED Pioneer Plus (PFP2) Floodlight Scene Lights, Pair, 12V, Whelen, Lightbar Mount, LED Pioneer (PFA2) Floodlight Scene Lights, Pair, 12V, Whelen, Lightbar Mount, LED Pioneer Plus (PFP2) Floodlight Scene Lights, Pair, 12V, Whelen, Pedestal Mount, LED PAR 36 Floodlight, Black Housing, Switch on Lighthead Scene Lights, Pair, 12V, Whelen, Pedestal Mount, LED Pioneer (PFA1) Floodlight, Switch on Lighthead Scene Lights, Pair, 12V, Whelen, Pedestal Mount, LED Pioneer (PFA2) Floodlight, Switch on Lighthead Scene Lights, Pair, 12V, Whelen, Pedestal Mount, LED Pioneer Plus (PCP2) Combo Spot/Flood, Switch on Lighthead Scene Lights, Pair, 12V, Whelen, Pedestal Mount, LED Pioneer Plus (PFP1) Floodlight , Switch on Lighthead Scene Lights, Pair, 12V, Whelen, Pedestal Mount, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead Scene Lights, Pair, 12V, Whelen, Semi-Recessed, LED Pioneer (PFA1) Floodlight Scene Lights, Pair, 12V, Whelen, Semi-Recessed, LED Pioneer (PFA2) Floodlight Scene Lights, Pair, 12V, Whelen, Semi-Recessed, LED Pioneer Plus (PCP2) Combo Spot/Flood Scene Lights, Pair, 12V, Whelen, Semi-Recessed, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 12V, Whelen, Semi-Recessed, LED Pioneer Plus (PFP2) Floodlight

110686 110687 110688 110689 110690 110691 110692 110693 110694 110695 110696 110697 110698 110699 110700 110701 110702 110703 110704 110705 110706 110707 110708 110709 110710 110711 110712 110713 110714 110715 110716 110717 110718 110719 110720 110721 110722 110723 110625 110626 110627 110628 110629 110630 110631 110632 110633 110634 110635 110636 110637 110638 110639 110640 110641 110642 110643 110644 110645 110646 110647 110648 110649 110650 110651 110652 110653 110654 110655 110656 110657 110658 110659 110660 110661 110662 110663 110664 110665 110666 110667 110668 110669 110670 110671 110672 110673 110674 110675 110676 110677 110678 110679 110680 110681 110682 110683 110684 110685 Scene Lights, Pair, 12V, Whelen, Surface Mount, Halogen 600 Series Opti-Scene Scene Lights, Pair, 12V, Whelen, Surface Mount, Halogen 700 Series Opti-Scene Scene Lights, Pair, 12V, Whelen, Surface Mount, Halogen 810 Series Scene Lights, Pair, 12V, Whelen, Surface Mount, Halogen 900 Series Opti-Scene Scene Lights, Pair, 12V, Whelen, Surface Mount, LED 600 Series Gradient Opti-Scene Scene Lights, Pair, 12V, Whelen, Surface Mount, LED 700 Series Gradient Opti-Scene Scene Lights, Pair, 12V, Whelen, Surface Mount, LED 900 Series Gradient Opti-Scene Scene Lights, Pair, 12V, Whelen, Surface Mount, LED M6 Series Gradient Scene Scene Lights, Pair, 12V, Whelen, Surface Mount, LED M9 Series Gradient Scene Scene Lights, Pair, 12V, Whelen, Surface Mount, LED Pioneer (PCP2) Combo Spot/Flood Scene Lights, Pair, 12V, Whelen, Surface Mount, LED Pioneer Plus Max (PCP3) Combo Spot/Flood Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer (PFA1) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer (PFA2) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PCP2) Combo Spot/Flood Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PFP2) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer (PFA1) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer (PFA2) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PCP2) Combo Spot/Flood Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PFP2) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer (PFA1) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer (PFA2) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer Plus (PCP2) Combo Spot/Flood Scene Lights, Pair, 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 12V, Whelen, Telescoping Thru The Roof Push-Up, LED Pioneer Plus (PFP2) Floodlight Scene Light, (1), 120V, FRC, Pedestal Mount, Halogen Focus 1000W, Switch on Lighthead Scene Light, (1), 120V, FRC, Pedestal Mount, Halogen Focus 500W, Switch on Lighthead Scene Light, (1), 120V, FRC, Pedestal Mount, Halogen Optimum 1000W, Switch on Lighthead Scene Light, (1), 120V, FRC, Pedestal Mount, Halogen Optimum 500W, Switch on Lighthead Scene Light, (1), 120V, FRC, Pedestal Mount, Halogen Optimum 750W, Switch on Lighthead Scene Light, (1), 120V, FRC, Pedestal Mount, LED Spectra 20,000 Lumen, Switch on Lighthead Scene Light, (1), 120V, FRC, Portable, Halogen Focus 500W, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Focus 500W, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Focus 500W, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Optimum 1000W, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Optimum 1000W, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Optimum 1000W, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Optimum 500W, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Optimum 500W, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Optimum 500W, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Optimum 750W, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Optimum 750W, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Portable, Halogen Optimum 750W, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Portable, LED Spectra 20,000 Lumen, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Portable, LED Spectra 20,000 Lumen, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Portable, LED Spectra 20,000 Lumen, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Focus 1000W, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Focus 1000W, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Focus 1000W, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Focus 500W, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Focus 500W, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Focus 500W, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Optimum 1000W, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Optimum 1000W, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Optimum 1000W, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Optimum 500W, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Optimum 500W, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Optimum 500W, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Optimum 750W, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Optimum 750W, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), Halogen Optimum 750W, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Tripod (Large), LED Spectra 20,000 Lumen, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), LED Spectra 20,000 Lumen, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Large), LED Spectra 20,000 Lumen, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, FRC, Tripod (Small), LED Spectra 20,000 Lumen, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Small), LED Spectra 20,000 Lumen, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, FRC, Tripod (Small), LED Spectra 20,000 Lumen, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, Whelen, Pedestal Mount, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead Scene Light, (1), 120V, Whelen, Pedestal Mount, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead Scene Light, (1), 120V, Whelen, Portable, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, Whelen, Portable, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, Whelen, Portable, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, Whelen, Portable, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, Whelen, Portable, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, Whelen, Portable, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, 5-15 Plug Scene Light, (1), 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-15 Plug Scene Light, (1), 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-20 Plug Scene Light, (1), 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP1) Floodlight, 5-15 Plug Scene Light, (1), 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP1) Floodlight, L5-15 Plug Scene Light, (1), 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP1) Floodlight, L5-20 Plug Scene Light, (1), 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP2) Floodlight, 5-15 Plug Scene Light, (1), 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP2) Floodlight, L5-15 Plug Scene Light, (1), 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP2) Floodlight, L5-20 Plug Scene Light, (1), 240V, FRC, Pedestal Mount, Halogen Focus 1000W, Switch on Lighthead Scene Light, (1), 240V, FRC, Pedestal Mount, Halogen Focus 1500W, Switch on Lighthead Scene Light, (1), 240V, FRC, Pedestal Mount, Halogen Optimum 1500W, Switch on Lighthead Scene Lights, Pair, 120V, Chassis Supplied, Brow (Wiring Only) Scene Lights, Pair, 120V, FRC, Brow Mount, Halogen Focus 1000W Scene Lights, Pair, 120V, FRC, Brow Mount, Halogen Focus 500W Scene Lights, Pair, 120V, FRC, Brow Mount, Halogen Focus 750W Scene Lights, Pair, 120V, FRC, Brow Mount, Halogen Optimum 1000W Scene Lights, Pair, 120V, FRC, Brow Mount, Halogen Optimum 500W Scene Lights, Pair, 120V, FRC, Brow Mount, Halogen Optimum 750W Scene Lights, Pair, 120V, FRC, Brow Mount, LED Spectra 20,000 Lumen

110785 110786 110787 110788 110789 110790 110791 110792 110793 110794 110795 110796 110797 110798 110799 110800 110801 110802 110803 110804 110805 110806 110807 110808 110809 110810 110811 110812 110813 110814 110815 110816 110817 110818 110819 110820 110821 110822 110724 110725 110726 110727 110728 110729 110730 110731 110732 110733 110734 110735 110736 110737 110738 110739 110740 110741 110742 110743 110744 110745 110746 110747 110748 110749 110750 110751 110752 110753 110754 110755 110756 110757 110758 110759 110760 110761 110762 110763 110764 110765 110766 110767 110768 110769 110770 110771 110772 110773 110774 110775 110776 110777 110778 110779 110780 110781 110782 110783 110784 Scene Lights, Pair, 120V, FRC, Pedestal Mount, Halogen Focus 1000W, Switch on Lighthead Scene Lights, Pair, 120V, FRC, Pedestal Mount, Halogen Focus 500W, Switch on Lighthead Scene Lights, Pair, 120V, FRC, Pedestal Mount, Halogen Optimum 1000W, Switch on Lighthead Scene Lights, Pair, 120V, FRC, Pedestal Mount, Halogen Optimum 500W, Switch on Lighthead Scene Lights, Pair, 120V, FRC, Pedestal Mount, Halogen Optimum 750W, Switch on Lighthead Scene Lights, Pair, 120V, FRC, Pedestal Mount, LED Spectra 20,000 Lumen, Switch on Lighthead Scene Lights, Pair, 120V, FRC, Portable, Halogen Focus 500W, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Focus 500W, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Focus 500W, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Optimum 1000W, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Optimum 1000W, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Optimum 1000W, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Optimum 500W, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Optimum 500W, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Optimum 500W, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Optimum 750W, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Optimum 750W, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, Halogen Optimum 750W, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Portable, LED Spectra 20,000 Lumen, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, LED Spectra 20,000 Lumen, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Portable, LED Spectra 20,000 Lumen, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Recessed, Halogen Focus 1000W Scene Lights, Pair, 120V, FRC, Recessed, Halogen Focus 500W Scene Lights, Pair, 120V, FRC, Recessed, Halogen Optimum 500W Scene Lights, Pair, 120V, FRC, Recessed, Halogen Optimum 750W Scene Lights, Pair, 120V, FRC, Surface Mount, LED Spectra 15,000 Lumen Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Pull-Up LED Spectra 20,000 Lumen Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Pull-Up, Halogen Focus 1000W Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Pull-Up, Halogen Focus 750W Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Pull-Up, Halogen Optimum 1000W Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Pull-Up, Halogen Optimum 750W Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Push-Up, Halogen Optimum 1000W Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 1000W Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 500W Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Push-Up, Halogen Focus 750W Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Push-Up, Halogen Optimum 500W Scene Lights, Pair, 120V, FRC, Telescoping Side Mount Push-Up, LED Spectra 20,000 Lumen Scene Lights, Pair, 120V, FRC, Telescoping Thru The Roof Push-Up, Halogen Optimum 1000W Scene Lights, Pair, 120V, FRC, Telescoping Thru The Roof Push-Up, Halogen Optimum 500W Scene Lights, Pair, 120V, FRC, Telescoping Thru The Roof Push-Up, Halogen Optimum 750W Scene Lights, Pair, 120V, FRC, Telescoping Thru The Roof Push-Up, LED Spectra 20,000 Lumen Scene Lights, Pair, 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Focus 500W Scene Lights, Pair, 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Focus 750W Scene Lights, Pair, 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 1000W Scene Lights, Pair, 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 500W Scene Lights, Pair, 120V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 750W Scene Lights, Pair, 120V, FRC, Telescoping Top Mount Pull-Up, LED Spectra 20,000 Lumen Spectra Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Focus 1000W, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Focus 1000W, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Focus 1000W, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Focus 500W, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Focus 500W, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Focus 500W, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Optimum 1000W, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Optimum 1000W, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Optimum 1000W, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Optimum 500W, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Optimum 500W, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Optimum 500W, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Optimum 750W, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Optimum 750W, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), Halogen Optimum 750W, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), LED Spectra 20,000 Lumen, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), LED Spectra 20,000 Lumen, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Large), LED Spectra 20,000 Lumen, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, FRC, Tripod (Small), LED Spectra 20,000 Lumen, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Small), LED Spectra 20,000 Lumen, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, FRC, Tripod (Small), LED Spectra 20,000 Lumen, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, Whelen, Brow Mount, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 120V, Whelen, Brow Mount, LED Pioneer Plus (PFP2) Floodlight Scene Lights, Pair, 120V, Whelen, Pedestal Mount, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead Scene Lights, Pair, 120V, Whelen, Pedestal Mount, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead Scene Lights, Pair, 120V, Whelen, Portable, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, Whelen, Portable, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, Whelen, Portable, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, Whelen, Portable, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, Whelen, Portable, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, Whelen, Portable, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, Whelen, Semi-Recessed, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 120V, Whelen, Semi-Recessed, LED Pioneer Plus (PFP2) Floodlight Scene Lights, Pair, 120V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 120V, Whelen, Telescoping Side Mount Pull-Up, LED Pioneer Plus (PFP2) Floodlight Scene Lights, Pair, 120V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 120V, Whelen, Telescoping Side Mount Push-Up, LED Pioneer Plus (PFP2) Floodlight Scene Lights, Pair, 120V, Whelen, Telescoping Thru The Roof Pull-Up, LED Pioneer Plus (PFP1) Floodlight Scene Lights, Pair, 120V, Whelen, Telescoping Thru The Roof Pull-Up, LED Pioneer Plus (PFP2) Floodlight Scene Lights, Pair, 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, 5-15 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-15 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Large), LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-20 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP1) Floodlight, 5-15 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP1) Floodlight, L5-15 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP1) Floodlight, L5-20 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP2) Floodlight, 5-15 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP2) Floodlight, L5-15 Plug Scene Lights, Pair, 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP2) Floodlight, L5-20 Plug Scene Lights, Pair, 240V, FRC, Brow Mount, Halogen Optimum 1500W

110884 110885 110886 110887 110888 110889 110890 110891 110892 110893 110894 110895 110896 110897 110898 110899 110900 110901 110902 110903 110904 110905 110906 110907 110908 110909 110910 110911 110914 110915 110916 110917 110918 110919 110920 110921 110922 110923 110823 110824 110825 110826 110827 110828 110829 110830 110831 110832 110833 110834 110835 110836 110837 110838 110839 110840 110841 110842 110843 110844 110845 110846 110847 110848 110849 110850 110851 110852 110853 110854 110855 110856 110857 110858 110859 110860 110861 110862 110863 110864 110865 110866 110867 110868 110869 110870 110871 110872 110873 110874 110875 110876 110877 110878 110879 110880 110881 110882 110883 Scene Lights, Pair, 240V, FRC, Pedestal Mount, Halogen Focus 1000W, Switch on Lighthead Scene Lights, Pair, 240V, FRC, Pedestal Mount, Halogen Focus 1500W, Switch on Lighthead Scene Lights, Pair, 240V, FRC, Pedestal Mount, Halogen Optimum 1500W, Switch on Lighthead Scene Lights, Pair, 240V, FRC, Recessed, Halogen Focus 1000W Scene Lights, Pair, 240V, FRC, Recessed, Halogen Optimum 1500W Scene Lights, Pair, 240V, FRC, Telescoping Side Mount Push-Up, Halogen Optimum 1500W Scene Lights, Pair, 240V, FRC, Telescoping Top Mount Pull-Up, Halogen Focus 1000W Scene Lights, Pair, 240V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 1000W Scene Lights, Pair, 240V, FRC, Telescoping Top Mount Pull-Up, Halogen Optimum 1500W Lighting Location, On Rear Face of Custom Chassis, Both Sides Lighting Activation, Circuit Breaker Only Lighting Activation, On Lighthead Only Lighting Activation, On V-Mux Screen and Pump Panel, 'FRONT SCENE' Lighting Activation, On V-Mux Screen and Pump Panel, 'LEFT SCENE' Lighting Activation, On V-Mux Screen and Pump Panel, 'REAR SCENE' Lighting Activation, On V-Mux Screen and Pump Panel, 'REAR SCENE', Wired to Reverse Lighting Activation, On V-Mux Screen and Pump Panel, 'RIGHT SCENE' Lighting Activation, On V-Mux Screen, 'FRONT SCENE' Lighting Activation, On V-Mux Screen, 'LEFT SCENE' Lighting Activation, On V-Mux Screen, 'LEFT SCENE' and 'RIGHT SCENE' Lighting Activation, On V-Mux Screen, 'REAR SCENE' Lighting Activation, On V-Mux Screen, 'REAR SCENE', Wired to Reverse Lighting Activation, On V-Mux Screen, RIGHT SCENE' Lighting Activation, Pair, Circuit Breakers Only Lighting Activation, Pair, On LightheadsOnly Lighting Activation, Pair, In Cab and On Pump Panel, 'LEFT SCENE' and 'RIGHT SCENE', Rocker Switches Lighting Activation, Pair, In Cab, 'LEFT SCENE' and 'RIGHT SCENE', Rocker Switches Lighting Activation, Pair, In Cab, Individually Switched Lights, Rocker Switches Lighting Activation, Pair, On Pump Panel, Individually Switched Lights Lighting Activation, Pair, On V-Mux Screen and Pump Panel, 'LEFT SCENE' and 'RIGHT SCENE' Scene Light Option, FRC, Wire Guard Scene Light Option, FRC, Switch on Light Head Scene Light Option, FRC, Steady Rest Bracket Scene Light Option, FRC, Pole Hazard Switch Scene Light Option, Whelen, Cradle Cord Reel, Akron, 120V, 150' 10/3 Yellow Cord, Hardwired Junction Box, Circle D Cord Reel, Akron, 120V, 150' 10/3 Yellow Cord, Hardwired Junction Box, Extenda-Lite Cord Reel, Akron, 120V, 150' 10/3 Yellow Cord, Terminate L5-20 Receptacle Cord Reel, Akron, 120V, 150' 10/3 Yellow Cord, Terminate L5-20 Receptacle, Junction Box with Pigtail, Circle D Cord Reel, Akron, 120V, 150' 10/3 Yellow Cord, Terminate L5-20 Receptacle, Junction Box with Pigtail, Extenda-Lite Cord Reel, Akron, 120V, 150' 10/3 Yellow Cord, Terminate L5-30 Receptacle Cord Reel, Akron, 120V, 150' 10/3 Yellow Cord, Terminate L5-30 Receptacle, Junction Box with Pigtail, Circle D Cord Reel, Akron, 120V, 150' 10/3 Yellow Cord, Terminate L5-30 Receptacle, Junction Box with Pigtail, Extenda-Lite Cord Reel, Akron, 120V, 200' 10/3 Yellow Cord, Hardwired Junction Box, Circle D Cord Reel, Akron, 120V, 200' 10/3 Yellow Cord, Hardwired Junction Box, Extenda-Lite Cord Reel, Akron, 120V, 200' 10/3 Yellow Cord, Terminate L5-20 Receptacle Cord Reel, Akron, 120V, 200' 10/3 Yellow Cord, Terminate L5-20 Receptacle, Junction Box with Pigtail, Circle D Cord Reel, Akron, 120V, 200' 10/3 Yellow Cord, Terminate L5-20 Receptacle, Junction Box with Pigtail, Extenda-Lite Cord Reel, Akron, 120V, 200' 10/3 Yellow Cord, Terminate L5-30 Receptacle Cord Reel, Akron, 120V, 200' 10/3 Yellow Cord, Terminate L5-30 Receptacle, Junction Box with Pigtail, Circle D Cord Reel, Akron, 120V, 200' 10/3 Yellow Cord, Terminate L5-30 Receptacle, Junction Box with Pigtail, Extenda-Lite Cord Reel, Hannay, 120V, 150' 10/3 Yellow Cord, Hardwired Junction Box, Circle D Cord Reel, Hannay, 120V, 150' 10/3 Yellow Cord, Hardwired Junction Box, Extenda-Lite Cord Reel, Hannay, 120V, 150' 10/3 Yellow Cord, Terminate L5-20 Receptacle Cord Reel, Hannay, 120V, 150' 10/3 Yellow Cord, Terminate L5-20 Receptacle, Junction Box with Pigtail, Circle D Cord Reel, Hannay, 120V, 150' 10/3 Yellow Cord, Terminate L5-20 Receptacle, Junction Box with Pigtail, Extenda-Lite Cord Reel, Hannay, 120V, 150' 10/3 Yellow Cord, Terminate L5-30 Receptacle Cord Reel, Hannay, 120V, 150' 10/3 Yellow Cord, Terminate L5-30 Receptacle, Junction Box with Pigtail, Circle D Cord Reel, Hannay, 120V, 150' 10/3 Yellow Cord, Terminate L5-30 Receptacle, Junction Box with Pigtail, Extenda-Lite Cord Reel, Hannay, 120V, 200' 10/3 Yellow Cord, Hardwired Junction Box, Circle D Cord Reel, Hannay, 120V, 200' 10/3 Yellow Cord, Hardwired Junction Box, Extenda-Lite Cord Reel, Hannay, 120V, 200' 10/3 Yellow Cord, Terminate L5-20 Receptacle Cord Reel, Hannay, 120V, 200' 10/3 Yellow Cord, Terminate L5-20 Receptacle, Junction Box with Pigtail, Circle D Cord Reel, Hannay, 120V, 200' 10/3 Yellow Cord, Terminate L5-20 Receptacle, Junction Box with Pigtail, Extenda-Lite Cord Reel, Hannay, 120V, 200' 10/3 Yellow Cord, Terminate L5-30 Receptacle Cord Reel, Hannay, 120V, 200' 10/3 Yellow Cord, Terminate L5-30 Receptacle, Junction Box with Pigtail, Circle D Cord Reel, Hannay, 120V, 200' 10/3 Yellow Cord, Terminate L5-30 Receptacle, Junction Box with Pigtail, Extenda-Lite Cord Reel, Hannay, 240V, 200' 10/3 Yellow Cord, Terminate L6-20 Receptacle Cord Reel, Hannay, 240V, 200' 10/3 Yellow Cord, Terminate L6-30 Receptacle Cord Reel, Hannay, 240V, 200' 10/4 Yellow Cord, Hardwired to Extenda-Lite Junction Box, Split (2) 15 Amp Circuits Cord Reel, Hannay, 240V, 200' 10/4 Yellow Cord, Terminate L14-20 Receptacle, Junction Box with Pigtail, Extenda-Lite, Split (2) 15 Amp Circuits Cord Reel, Hannay, 240V, 200' 10/4 Yellow Cord, Terminate L14-30 Receptacle, Junction Box with Pigtail, Extenda-Lite, Split (2) 15 Amp Circuits Cord Reel, Hannay, 240V, 200' 10/4 Yellow Cord, Terminate L6-20 Receptacle Cord Reel, Hannay, 240V, 200' 10/4 Yellow Cord, Terminate L6-30 Receptacle Junction Box Option, High Visibility Yellow Junction Box Receptacle, 120V, FP-11 Firepower, Single Cord Reel Location, Below Cab Crew Door, Terminate Thru Roller Assembly on Step Overlay, Driver's Side Cord Reel Location, Below Cab Crew Door, Terminate Thru Roller Assembly on Step Overlay, Officer's Side Cord Reel Location, In Hatch Cmpt, Driver's Side, Terminate Thru Roller Assembly in Top of L1 Cmpt Cord Reel Location, In Hatch Cmpt, Driver's Side, Terminate Thru Roller Assembly in Top of L3 Cmpt Cord Reel Location, In Hatch Cmpt, Officer's Side, Terminate Thru Roller Assembly in Top of R1 Cmpt Cord Reel Location, In Hatch Cmpt, Officer's Side, Terminate Thru Roller Assembly in Top of R3 Cmpt Cord Reel Location, In Pump Module, Terminate Thru Roller Assembly on Side Access Door, Driver's Side Cord Reel Location, In Pump Module, Terminate Thru Roller Assembly on Side Access Door, Officer's Side Cord Reel Location, In Pump Module, Terminate Thru Roller Assembly on Side Pump Module, Driver's Side Cord Reel Location, In Pump Module, Terminate Thru Roller Assembly on Side Pump Module, Officer's Side Cord Reel Location, In Pump Module, Terminate Thru Roller Assembly on Top Pump Module, Center Cord Reel Location, In Pump Module, Terminate Thru Roller Assembly on Top Pump Module, Driver's Side Cord Reel Location, In Pump Module, Terminate Thru Roller Assembly on Top Pump Module, Officer's Side Cord Reel Location, In Rear Cmpt, Between Frame Rails, Painted Access Door Cord Reel Location, In Rear Cmpt, Between Frame Rails, Terminate Thru Roller Assembly on Painted Access Door Receptacle, 120V, FP-10 Firepower, Single, Wired to Shoreline Receptacle, 120V, FP-10 Firepower, Single, Wired to Generator Junction Box Mounting Bracket, Tread Plate Receptacle, 120V, FP-11 Firepower, Single, Wired to Shoreline Receptacle, 120V, FP-11 Firepower, Single, Wired to Generator Receptacle, 120V, FP-11 Firepower, Single, Wired to Transfer Switch Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Amkus 10,000 psi Package, Blue/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Amkus 10,000 psi Package, Red/Black Hose

110985 110988 110989 110990 110991 110992 110993 110994 110995 110996 110997 110998 110999 111000 111001 111002 111003 111004 111005 111006 111007 111008 111009 111010 111011 111012 111013 111014 111015 111016 111017 111018 111019 111020 111021 111022 111023 111024 110924 110925 110926 110927 110928 110929 110930 110931 110932 110933 110934 110935 110936 110937 110938 110939 110940 110941 110942 110943 110944 110945 110946 110947 110948 110949 110950 110951 110952 110953 110954 110955 110956 110957 110958 110959 110960 110961 110962 110963 110964 110965 110966 110967 110968 110969 110970 110971 110972 110973 110974 110975 110976 110977 110978 110979 110980 110981 110982 110983 110984 Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Centaur 10,000 psi Package, Red/Blue Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Centaur 10,000 psi Package, Yellow/Blue Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Genesis 10,000 psi Package, Blue/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Genesis 10,000 psi Package, Red/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Holmatro 10,000 psi Package, Blue/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Holmatro 10,000 psi Package, Red/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Hurst 5,000 psi Package, Blue Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Hurst 5,000 psi Package, Green Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Hurst 5,000 psi Package, Orange Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Hurst 5,000 psi Package, Yellow Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Hurst 5,000 psi Package, Streamline Couplers, Blue Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Hurst 5,000 psi Package, Streamline Couplers, Green Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Hurst 5,000 psi Package, Streamline Couplers, Orange Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, Hurst 5,000 psi Package, Streamline Couplers, Yellow Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, TNT 10,000 psi Package, Blue/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Red Enamel Finish, TNT 10,000 psi Package, Red/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Amkus 10,000 psi Package, Blue/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Amkus 10,000 psi Package, Red/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Centaur 10,000 psi Package, Red/Blue Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Centaur 10,000 psi Package, Yellow/Blue Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Genesis 10,000 psi Package, Blue/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Genesis 10,000 psi Package, Red/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Holmatro 10,000 psi Package, Blue/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Holmatro 10,000 psi Package, Red/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Hurst 5,000 psi Package, Blue Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Hurst 5,000 psi Package, Green Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Hurst 5,000 psi Package, Orange Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Hurst 5,000 psi Package, Yellow Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Hurst 5,000 psi Package, Streamline Couplers, Blue Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Hurst 5,000 psi Package, Streamline Couplers, Green Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Hurst 5,000 psi Package, Streamline Couplers, Orange Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, Hurst 5,000 psi Package, Streamline Couplers, Yellow Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, TNT 10,000 psi Package, Blue/Black Hose Hydraulic Reel with 100' Hose/Lead-Ins, Hannay, Stainless Steel Finish, TNT 10,000 psi Package, Red/Black Hose Hydraulic Reel Location, In Hatch Cmpt, Driver's Side, Terminate Thru Roller Assembly in Top of L1 Cmpt Hydraulic Reel Location, In Hatch Cmpt, Driver's Side, Terminate Thru Roller Assembly in Top of L3 Cmpt Hydraulic Reel Location, In Hatch Cmpt, Officer's Side, Terminate Thru Roller Assembly in Top of R1 Cmpt Hydraulic Reel Location, In Hatch Cmpt, Officer's Side, Terminate Thru Roller Assembly in Top of R3 Cmpt Air Horn Activation, Lanyard, Dual Control, Driver and Officer Air Horn Activation, Push Button, Center Console Air Horn Activation, Push Button on Pump Panel, Officer's Side Air Horn Activation, Push Button on Pump Panels, Both Sides Siren Activation, (1) Push Button, Center Console Siren Activation, (2) Foot Switches, Driver's and Officer's Side Siren Activation, (2) Push Buttons, Driver's and Officer's Side Siren Head, 100W/200W, Powercall, DX5200 Speaker, (1), 100W, Whelen, SA122FMP, Recess Mounted Speaker, (1), 100W, Whelen, SA315P, Recess Mounted Speakers, (2), 100W, Cast Products, Compact, Recess Mounted Speakers, (2), 100W, Cast Products, ITB, Recess Mounted Speakers, (2), 100W, Dynamax, ES100, Flush Mounted Speakers, (2), 100W, Whelen, SA122FMP, Recess Mounted Speakers, (2), 100W, Whelen, SA315P, Recess Mounted Speakers, (2), Chassis Supplied, OEM Installed Power and Ground Lead, 12V Drop, Ignition, 14 Gauge Wire Power and Ground Lead, 12V Drop, Ignition, 10 Gauge Wire, 6-Position Distribution Panel Power and Ground Lead, 12V Drop, Ignition, 8 Gauge Wire, 12-Position Distribution Panel Power and Ground Lead, 12V Drop, Master, 14 Gauge Wire Power and Ground Lead, 12V Drop, Master, 10 Gauge Wire, 6-Position Distribution Panel Power and Ground Lead, 12V Drop, Master, 8 Gauge Wire, 12-Position Distribution Panel Accessory (Cigarette Lighter) Outlet, 12V, Ignition Accessory (Cigarette Lighter) Outlet, 12V, Master Accessory (USB) Dual Outlet, 12V, Master Scene Light Options, FRC, Wire Guards Scene Light Options, FRC, Switches on Light Head Scene Light Options, FRC, Steady Rest Brackets Scene Light Options, FRC, Pole Hazard Switches Scene Light Options, Whelen, Cradles Running Board, Driver's Side, Bolt-On, Tread Plate, Storage Well, Fixed, PAC Straps Running Board, Driver's Side, Bolt-On, Tread Plate, Storage Well, Fixed, Tread Plate Cover Running Board, Driver's Side, Bolt-On, Tread Plate, Storage Well, Fixed, Vinyl Cover, Black Running Board, Driver's Side, Bolt-On, Tread Plate, Storage Well, Fixed, Vinyl Cover, Red Running Board, Driver's Side, Bolt-On, Tread Plate, Storage Well, Floating, PAC Straps Running Board, Driver's Side, Bolt-On, Tread Plate, Storage Well, Floating, Tread Plate Cover Running Board, Driver's Side, Bolt-On, Tread Plate, Storage Well, Floating, Vinyl Cover, Black Running Board, Driver's Side, Bolt-On, Tread Plate, Storage Well, Floating, Vinyl Cover, Red Running Board, Driver's Side, Integral, Tread Plate, Storage Well, Fixed, PAC Straps Running Board, Driver's Side, Integral, Tread Plate, Storage Well, Fixed, Tread Plate Cover Running Board, Driver's Side, Integral, Tread Plate, Storage Well, Fixed, Vinyl Cover, Black Running Board, Driver's Side, Integral, Tread Plate, Storage Well, Fixed, Vinyl Cover, Red Running Board, Driver's Side, Integral, Tread Plate, Storage Well, Floating, PAC Straps Running Board, Driver's Side, Integral, Tread Plate, Storage Well, Floating, Tread Plate Cover Running Board, Driver's Side, Integral, Tread Plate, Storage Well, Floating, Vinyl Cover, Black Running Board, Driver's Side, Integral, Tread Plate, Storage Well, Floating, Vinyl Cover, Red Running Board, Officer's Side, Bolt-On, Tread Plate, Storage Well, Fixed, PAC Straps Running Board, Officer's Side, Bolt-On, Tread Plate, Storage Well, Fixed, Tread Plate Cover Running Board, Officer's Side, Bolt-On, Tread Plate, Storage Well, Fixed, Vinyl Cover, Black Running Board, Officer's Side, Bolt-On, Tread Plate, Storage Well, Fixed, Vinyl Cover, Red Running Board, Officer's Side, Bolt-On, Tread Plate, Storage Well, Floating, PAC Straps Running Board, Officer's Side, Bolt-On, Tread Plate, Storage Well, Floating, Tread Plate Cover Running Board, Officer's Side, Bolt-On, Tread Plate, Storage Well, Floating, Vinyl Cover, Black Running Board, Officer's Side, Bolt-On, Tread Plate, Storage Well, Floating, Vinyl Cover, Red Running Board, Officer's Side, Integral, Tread Plate, Storage Well, Fixed, PAC Straps Running Board, Officer's Side, Integral, Tread Plate, Storage Well, Fixed, Tread Plate Cover Running Board, Officer's Side, Integral, Tread Plate, Storage Well, Fixed, Vinyl Cover, Black Running Board, Officer's Side, Integral, Tread Plate, Storage Well, Fixed, Vinyl Cover, Red Running Board, Officer's Side, Integral, Tread Plate, Storage Well, Floating, PAC Straps Running Board, Officer's Side, Integral, Tread Plate, Storage Well, Floating, Tread Plate Cover Running Board, Officer's Side, Integral, Tread Plate, Storage Well, Floating, Vinyl Cover, Black

111086 111087 111088 111089 111091 111092 111093 111094 111095 111096 111097 111098 111099 111100 111101 111102 111103 111104 111105 111106 111107 111108 111109 111110 111111 111112 111113 111114 111115 111117 111118 111127 111128 111129 111130 111131 111132 111133 111025 111026 111027 111028 111029 111030 111031 111032 111033 111034 111035 111036 111037 111038 111039 111040 111041 111042 111043 111044 111045 111046 111047 111048 111049 111050 111051 111052 111053 111054 111055 111056 111057 111058 111059 111060 111061 111062 111063 111064 111065 111066 111067 111068 111069 111070 111071 111072 111073 111074 111075 111076 111077 111078 111079 111080 111081 111082 111083 111084 111085 Running Board, Officer's Side, Integral, Tread Plate, Storage Well, Floating, Vinyl Cover, Red Running Board Storage Well Tile, (1), Dri-Dek Flooring Running Board Storage Well Tile, (1), DuraDek Flooring Running Board Storage Well Tile, (1), Turtle Tile Flooring Running Board Storage Well Tile, (2), Dri-Dek Flooring Running Board Storage Well Tile, (2), DuraDek Flooring Running Board Storage Well Tile, (2), Turtle Tile Flooring Engineers Compartments, Lap Doors, ROM LED Lighting, No Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, ROM LED Lighting, No Shelf, No Tiles Engineers Compartments, Lap Doors, ROM LED Lighting, No Shelf, Turtle Tiles Engineers Compartments, Lap Doors, ROM LED Lighting, (1) Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, ROM LED Lighting, (1) Shelf, No Tiles Engineers Compartments, Lap Doors, ROM LED Lighting, (1) Shelf, Turtle Tiles Engineers Compartments, Lap Doors, Amdor LED Lighting, No Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, Amdor LED Lighting, No Shelf, No Tiles Engineers Compartments, Lap Doors, Amdor LED Lighting, No Shelf, Turtle Tiles Engineers Compartments, Lap Doors, Amdor LED Lighting, (1) Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, Amdor LED Lighting, (1) Shelf, No Tiles Engineers Compartments, Lap Doors, Amdor LED Lighting, (1) Shelf, Turtle Tiles Engineers Compartments, Lap Doors, Hansen LED Lighting, No Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, Hansen LED Lighting, No Shelf, No Tiles Engineers Compartments, Lap Doors, Hansen LED Lighting, No Shelf, Turtle Tiles Engineers Compartments, Lap Doors, Hansen LED Lighting, (1) Shelf, Dri-Dek Tiles Engineers Compartments, Lap Doors, Hansen LED Lighting, (1) Shelf, No Tiles Engineers Compartments, Lap Doors, Hansen LED Lighting, (1) Shelf, Turtle Tiles Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-400, Blue LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-600 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, psi 0-600, Blue LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, Dual Scale 0-400 / 0-2800 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, Dual Scale 0-400 / 0-2800, Blue LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, Dual Scale 0-600 / 0-4200 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge with Bezel, Orange Tip Pointer, Dual Scale 0-600 / 0-4200, Blue LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-400 Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-400, Both White LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-600 Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-600, Both White LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, Dual Scale -30-0-400 / -100-0-2800 Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, Dual Scale -30-0-400 / -100-0-2800, Both White LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, Dual Scale -30-0-600 / -100-0-4000 Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, Dual Scale -30-0-600 / -100-0-4000, Both White LED Backlit Flowminder Value System, Class 1, Pressure Gauge, 2-1/2", Liquid Filled, psi 0-400, Blue LED Lit Test Ports, Pressure/Vacuum, Inn. Cntrls, Operators Panel Test Ports, Pressure/Vacuum, Inn. Cntrls, L1 Compartment Pump and Engine Cooling System, Inn. Cntrls, 3/8" I.D., Hose, Controls on Pump Panel Pump and Engine Cooling System, Inn. Cntrls, 3/4" I.D., Hose, Controls on Pump Panel Pump and Engine Cooling System, Inn. Cntrls, 3/8" I.D., Hose, Controls in L1 Pump and Engine Cooling System, Inn. Cntrls, 3/4" I.D., Hose, Controls in L1 Bleeder Valve, Inn. Cntrls Intake Relief Valve, Steamer, Akron, #59, Factory Preset Intake Relief Valve, Steamer, Akron, #59, Factory Preset, With 2-1/2" CSA Adapter Intake Relief Valve, Steamer, Elkhart, Factory Preset Intake Relief Valve, Steamer, Elkhart, Factory Preset, With 2-1/2" CSA Adapter Intake Relief Valve, Steamer, Elkhart, Preset to 125 PSI Intake Relief Valve, Steamer, TFT A1850, Factory Preset Intake Relief Valve, Steamer, Trident, AirMax Butterfly Valve, Side Steamer, 5" Electric, Akron, Manual Override Access Butterfly Valve, Side Steamer, 5" Electric, Elkhart, Manual Override Access Butterfly Valve, Side Steamer, 6" Electric, Akron, Manual Override Access Butterfly Valve, Side Steamer, 6" Electric, Darley, Manual Override Access Butterfly Valve, Side Steamer, 6" Electric, Elkhart, Manual Override Access Butterfly Valve, Side Steamer, 6" Electric, Hale MIV-E, Manual Override Access Butterfly Valve, Side Steamer, 6" Electric, Waterous Monarch, Manual Override Access Butterfly Valve, Front Steamer, 5" Electric, Akron, Manual Override Access Butterfly Valve, Front Steamer, 5" Electric, Elkhart, Manual Override Access Butterfly Valve, Front Steamer, 6" Electric, Darley, Manual Override Access Butterfly Valve, Front Steamer, 6" Electric, Hale MIV-E, Manual Override Access Butterfly Valve, Front Steamer, 6" Electric, Waterous Monarch, Manual Override Access Butterfly Valve, Rear Steamer, 5" Electric, Akron, Manual Override Access Butterfly Valve, Rear Steamer, 5" Electric, Elkhart, Manual Override Access Discharge Relief Valve, Darley, FRC Throttle Xcel, Pump Hour Meter Discharge Relief Valve, Hale, FRC Throttle Xcel, Pump Hour Meter Discharge Relief Valve, Waterous, FRC Throttle Xcel, Pump Hour Meter Governor, FRC, PRO-T Overheat Protection Manager (OPM), Waterous, With Lights and Buzzer Overheat Protection System, Darley, With Lights and Buzzer Pump Color, Gray, Steamers and Inlets Black Off-Truck Pickup, Feecon, Foam Access Kit Front Bumper 1-1/2" Discharge Option, Plumbing Insulation Front Bumper Hosewell Option, Hose Out Indicator Light, Driver's Side Pump Panel Front Bumper Discharge Option, Air Chuck Blow-Out, Driver's Side Pump Panel Drains, Innovative Controls, Manual Quarter-Turn Drains, Innovative Controls, Manual Quarter-Turn, Class 1 Auto Drains on Pre-Connects Intake Relief Valve, Pump, Akron, #59, Factory Preset Intake Relief Valve, Pump, Akron, #59, Factory Preset, With 2-1/2" CSA Adapter Intake Relief Valve, Pump, Elkhart, Preset to 125 PSI Intake Relief Valve, Pump, Elkhart, Factory Preset, With 2-1/2" CSA Adapter Intake Relief Valve, Pump, TFT A1850, Factory Preset Mechanical Seals, Darley Pump Panels, Side Mount, Controls on Driver's Side, IC Overlay Label, Painted Aluminum Panels SG-09 Auxiliary Power Unit, Integrated System, No Heater, Leece-Neville Alternator SG-09 Auxiliary Power Unit, Integrated System, No Heater, Niehoff Alternator Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-400, Both Red LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-400, Both Blue LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-600, Both Red LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, psi -30-0-600, Both Blue LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, Dual Scale -30-0-400 / -100-0-2800, Both Red LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, Dual Scale -30-0-400 / -100-0-2800, Both Blue LED Backlit Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, Dual Scale -30-0-600 / -100-0-4000, Both Red LED Backlit

111195 111196 111197 111198 111199 111200 111201 111202 111203 111204 111205 111206 111207 111208 111209 111210 111211 111212 111213 111214 111215 111216 111217 111218 111219 111220 111221 111222 111223 111224 111225 111226 111227 111228 111229 111230 111231 111232 111134 111135 111136 111137 111138 111139 111140 111141 111142 111143 111144 111145 111146 111147 111148 111149 111150 111151 111152 111153 111154 111155 111156 111157 111158 111159 111160 111161 111162 111163 111164 111165 111166 111167 111168 111169 111170 111171 111172 111173 111174 111175 111176 111177 111178 111179 111180 111181 111182 111183 111184 111185 111186 111187 111188 111189 111190 111191 111192 111193 111194 Master Pressure Gauge Assembly with Test Ports, Inn. Cntrls, 4", Liquid Filled, Brass Case Gauges, Dual Scale -30-0-600 / -100-0-4000, Both Blue LED Backlit Pump Panels, CORE, Controls in L1, Line-X Panels, IC Bezels/Trim Rings/Labels Pump Panels, CORE, Controls in L1, Stainless Panels, IC Bezels/Trim Rings/Labels Overlay, Tread Plate, Inside Facing Sides of Recessed Rear and Rear Center Area Overlay, Tread Plate, Behind Rear Steps, Both Sides Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, Perimeter 3 x 7 Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, Perimeter 3 x 7 Dual Color Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, Perimeter 4 x 6 Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, PriZm II Perimeter 3 x 7, 12 LED Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Split Side-By-Side Style Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 8 LED Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, T-Rex Series Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, X Exterior Series, Dual Head, Side-By-Side Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, X Exterior Series, Dual Head, Stacked Lower Zone Warning Light Package, (10) OEM Sup., Code 3, LED, X Exterior Series, Single Head Lower Zone Warning Light Package, (10) OEM Sup., Federal Signal, LED, MicroPulse 6 Lower Zone Warning Light Package, (10) OEM Sup., Federal Signal, LED, QuadraFlare 6 x 4 Lower Zone Warning Light Package, (10) OEM Sup., Federal Signal, LED, QuadraFlare 6 x 4 Split Over-Under Lower Zone Warning Light Package, (10) OEM Sup., PowerArc, LED, M90FK Series Lower Zone Warning Light Package, (10) OEM Sup., PowerArc, LED, P14SM Series Lower Zone Warning Light Package, (10) OEM Sup., Weldon, LED, Diamondback 4 x 6 Lower Zone Warning Light Package, (10) OEM Sup., Weldon, LED, Diamondback 4 x 6 Split (Vertical) Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, 400 Series Single Level Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, 500 Series Split Side-By-Side Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, 500 Series TIR6 Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, 500 Series TIR6 Split Side-By-Side Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, 600 Series Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, 600 Series ROTA-BEAM Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, 600 Series Side-By-Side Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, 700 Series Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, ION Wide Angle Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, LINZ6 Series Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, LINZ6 Series Split Side-By-Side Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, M4 Series Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, M6 Series Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, M6 Series Split Side-By-Side Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, M6V2 Series (Warning/Perimeter) Lower Zone Warning Light Package, (10) OEM Sup., Whelen, LED, M7 Series Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, Perimeter 3 x 7 Dual Color Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, PriZm II Perimeter 3 x 7, 12 LED Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Split Side-By-Side Style Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 8 LED Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, T-Rex Series Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, X Exterior Series, Dual Head, Side-By-Side Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, X Exterior Series, Dual Head, Stacked Lower Zone Warning Light Package, (4) OEM Sup., Code 3, LED, X Exterior Series, Single Head Lower Zone Warning Light Package, (4) OEM Sup., Federal Signal, LED, MicroPulse 6 Lower Zone Warning Light Package, (4) OEM Sup., Federal Signal, LED, QuadraFlare 6 x 4 Split Over-Under Lower Zone Warning Light Package, (4) OEM Sup., PowerArc, LED, M90FK Series Lower Zone Warning Light Package, (4) OEM Sup., PowerArc, LED, P14SM Series Lower Zone Warning Light Package, (4) OEM Sup., Weldon, LED, Diamondback 4 x 6 Lower Zone Warning Light Package, (4) OEM Sup., Weldon, LED, Diamondback 4 x 6 Split (Vertical) Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, 400 Series Single Level Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, 500 Series Split Side-By-Side Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, 500 Series TIR6 Split Side-By-Side Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, ION Wide Angle Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, LINZ6 Series Split Side-By-Side Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, M4 Series Lower Zone Warning Light Package, (4) OEM Sup., Whelen, LED, M6V2 Series (Warning/Perimeter) Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, Perimeter 3 x 7 Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, Perimeter 3 x 7 Dual Color Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, Perimeter 4 x 6 Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, PriZm II Perimeter 3 x 7, 12 LED Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Split Side-By-Side Style Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 8 LED Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, T-Rex Series Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, X Exterior Series, Dual Head, Side-By-Side Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, X Exterior Series, Dual Head, Stacked Lower Zone Warning Light Package, (6) OEM Sup., Code 3, LED, X Exterior Series, Single Head Lower Zone Warning Light Package, (6) OEM Sup., Federal Signal, LED, MicroPulse 6 Lower Zone Warning Light Package, (6) OEM Sup., Federal Signal, LED, QuadraFlare 6 x 4 Lower Zone Warning Light Package, (6) OEM Sup., Federal Signal, LED, QuadraFlare 6 x 4 Split Over-Under Lower Zone Warning Light Package, (6) OEM Sup., PowerArc, LED, M90FK Series Lower Zone Warning Light Package, (6) OEM Sup., PowerArc, LED, P14SM Series Lower Zone Warning Light Package, (6) OEM Sup., Weldon, LED, Diamondback 4 x 6 Lower Zone Warning Light Package, (6) OEM Sup., Weldon, LED, Diamondback 4 x 6 Split (Vertical) Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, 400 Series Single Level Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, 500 Series Split Side-By-Side Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, 500 Series TIR6 Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, 500 Series TIR6 Split Side-By-Side Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, 600 Series Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, 600 Series ROTA-BEAM Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, 600 Series Side-By-Side Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, 700 Series Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, ION Wide Angle Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, LINZ6 Series Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, LINZ6 Series Split Side-By-Side Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, M4 Series Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, M6 Series Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, M6 Series Split Side-By-Side Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, M6V2 Series (Warning/Perimeter) Lower Zone Warning Light Package, (6) OEM Sup., Whelen, LED, M7 Series Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, Perimeter 3 x 7 Dual Color Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, PriZm II Perimeter 3 x 7, 12 LED Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Split Side-By-Side Style

111294 111295 111296 111297 111298 111299 111300 111301 111302 111303 111304 111305 111306 111307 111308 111309 111310 111311 111312 111313 111314 111315 111316 111317 111318 111319 111320 111321 111322 111323 111324 111325 111326 111327 111328 111329 111330 111331 111233 111234 111235 111236 111237 111238 111239 111240 111241 111242 111243 111244 111245 111246 111247 111248 111249 111250 111251 111252 111253 111254 111255 111256 111257 111258 111259 111260 111261 111262 111263 111264 111265 111266 111267 111268 111269 111270 111271 111272 111273 111274 111275 111276 111277 111278 111279 111280 111281 111282 111283 111284 111285 111286 111287 111288 111289 111290 111291 111292 111293 Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, PriZm II Perimeter 4 x 6, 8 LED Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, T-Rex Series Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, X Exterior Series, Dual Head, Side-By-Side Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, X Exterior Series, Dual Head, Stacked Lower Zone Warning Light Package, (8) OEM Sup., Code 3, LED, X Exterior Series, Single Head Lower Zone Warning Light Package, (8) OEM Sup., Federal Signal, LED, MicroPulse 6 Lower Zone Warning Light Package, (8) OEM Sup., Federal Signal, LED, QuadraFlare 6 x 4 Split Over-Under Lower Zone Warning Light Package, (8) OEM Sup., PowerArc, LED, M90FK Series Lower Zone Warning Light Package, (8) OEM Sup., PowerArc, LED, P14SM Series Lower Zone Warning Light Package, (8) OEM Sup., Weldon, LED, Diamondback 4 x 6 Lower Zone Warning Light Package, (8) OEM Sup., Weldon, LED, Diamondback 4 x 6 Split (Vertical) Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, 400 Series Single Level Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, 500 Series Split Side-By-Side Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, 500 Series TIR6 Split Side-By-Side Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, ION Wide Angle Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, LINZ6 Series Split Side-By-Side Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, M4 Series Lower Zone Warning Light Package, (8) OEM Sup., Whelen, LED, M6V2 Series (Warning/Perimeter) Upper Zone A, Lightbars (2), Power Arc, 25" Volt, VM2502GXP-1P-RC Upper Zone B/D, Warning Lights (2), Code 3, LED, Perimeter 3 x 7 Upper Zone B/D, Warning Lights (2), Code 3, LED, Perimeter 3 x 7 Dual Color Upper Zone B/D, Warning Lights (2), Code 3, LED, Perimeter 4 x 6 Upper Zone B/D, Warning Lights (2), Code 3, LED, Perimeter 7 x 9 Upper Zone B/D, Warning Lights (2), Code 3, LED, PriZm II Perimeter 3 x 7, 12 LED Upper Zone B/D, Warning Lights (2), Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Upper Zone B/D, Warning Lights (2), Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Split Side-By-Side Style Upper Zone B/D, Warning Lights (2), Code 3, LED, PriZm II Perimeter 4 x 6, 8 LED Upper Zone B/D, Warning Lights (2), Code 3, LED, PriZm II Perimeter 7 x 9, 8 LED Upper Zone B/D, Warning Lights (2), Code 3, LED, T-Rex Series Upper Zone B/D, Warning Lights (2), Code 3, LED, X Exterior Series, Dual Head, Side-By-Side Upper Zone B/D, Warning Lights (2), Code 3, LED, X Exterior Series, Dual Head, Stacked Upper Zone B/D, Warning Lights (2), Code 3, LED, X Exterior Series, Single Head Upper Zone B/D, Warning Lights (2), Federal Signal, LED, MicroPulse 6 Upper Zone B/D, Warning Lights (2), Federal Signal, LED, QuadraFlare 6 x 4 Upper Zone B/D, Warning Lights (2), Federal Signal, LED, QuadraFlare 6 x 4 Split Over-Under Upper Zone B/D, Warning Lights (2), Federal Signal, LED, QuadraFlare 9 x 7 Upper Zone B/D, Warning Lights (2), PowerArc, LED, LED210 Series Upper Zone B/D, Warning Lights (2), PowerArc, LED, M90FK Series Upper Zone B/D, Warning Lights (2), PowerArc, LED, P14SM Series Upper Zone B/D, Warning Lights (2), Weldon, LED, Diamondback 4 x 6 Upper Zone B/D, Warning Lights (2), Weldon, LED, Diamondback 4 x 6 Split (Vertical) Upper Zone B/D, Warning Lights (2), Whelen, LED, 400 Series Single Level Upper Zone B/D, Warning Lights (2), Whelen, LED, 500 Series Split Side-By-Side Upper Zone B/D, Warning Lights (2), Whelen, LED, 500 Series TIR6 Upper Zone B/D, Warning Lights (2), Whelen, LED, 500 Series TIR6 Split Side-By-Side Upper Zone B/D, Warning Lights (2), Whelen, LED, 600 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, 600 Series ROTA-BEAM Upper Zone B/D, Warning Lights (2), Whelen, LED, 600 Series Side-By-Side Upper Zone B/D, Warning Lights (2), Whelen, LED, 700 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, 900 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, 900 Series Over-Under Upper Zone B/D, Warning Lights (2), Whelen, LED, ION Wide Angle Upper Zone B/D, Warning Lights (2), Whelen, LED, LIN3 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, LINZ6 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, LINZ6 Series Split Side-By-Side Upper Zone B/D, Warning Lights (2), Whelen, LED, M4 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, M6 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, M6 Series Split Side-By-Side Upper Zone B/D, Warning Lights (2), Whelen, LED, M6V2 Series (Warning/Perimeter) Upper Zone B/D, Warning Lights (2), Whelen, LED, M7 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, M9 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, M9 Series Split Side-By-Side Upper Zone B/D, Warning Lights (2), Whelen, LED, M9V2 Series Upper Zone B/D, Warning Lights (2), Whelen, LED, TIR3 Series Upper Zone B/D, Warning Lights (4), Code 3, LED, Perimeter 3 x 7 Upper Zone B/D, Warning Lights (4), Code 3, LED, Perimeter 3 x 7 Dual Color Upper Zone B/D, Warning Lights (4), Code 3, LED, Perimeter 4 x 6 Upper Zone B/D, Warning Lights (4), Code 3, LED, Perimeter 7 x 9 Upper Zone B/D, Warning Lights (4), Code 3, LED, PriZm II Perimeter 3 x 7, 12 LED Upper Zone B/D, Warning Lights (4), Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Upper Zone B/D, Warning Lights (4), Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Split Side-By-Side Style Upper Zone B/D, Warning Lights (4), Code 3, LED, PriZm II Perimeter 4 x 6, 8 LED Upper Zone B/D, Warning Lights (4), Code 3, LED, PriZm II Perimeter 7 x 9, 8 LED Upper Zone B/D, Warning Lights (4), Code 3, LED, T-Rex Series Upper Zone B/D, Warning Lights (4), Code 3, LED, X Exterior Series, Dual Head, Side-By-Side Upper Zone B/D, Warning Lights (4), Code 3, LED, X Exterior Series, Dual Head, Stacked Upper Zone B/D, Warning Lights (4), Code 3, LED, X Exterior Series, Single Head Upper Zone B/D, Warning Lights (4), Federal Signal, LED, MicroPulse 6 Upper Zone B/D, Warning Lights (4), Federal Signal, LED, QuadraFlare 6 x 4 Upper Zone B/D, Warning Lights (4), Federal Signal, LED, QuadraFlare 6 x 4 Split Over-Under Upper Zone B/D, Warning Lights (4), Federal Signal, LED, QuadraFlare 9 x 7 Upper Zone B/D, Warning Lights (4), PowerArc, LED, M90FK Series Upper Zone B/D, Warning Lights (4), PowerArc, LED, P14SM Series Upper Zone B/D, Warning Lights (4), Weldon, LED, Diamondback 4 x 6 Upper Zone B/D, Warning Lights (4), Weldon, LED, Diamondback 4 x 6 Split (Vertical) Upper Zone B/D, Warning Lights (4), Whelen, LED, 400 Series Single Level Upper Zone B/D, Warning Lights (4), Whelen, LED, 500 Series Split Side-By-Side Upper Zone B/D, Warning Lights (4), Whelen, LED, 500 Series TIR6 Upper Zone B/D, Warning Lights (4), Whelen, LED, 500 Series TIR6 Split Side-By-Side Upper Zone B/D, Warning Lights (4), Whelen, LED, 600 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, 600 Series ROTA-BEAM Upper Zone B/D, Warning Lights (4), Whelen, LED, 600 Series Side-By-Side Upper Zone B/D, Warning Lights (4), Whelen, LED, 700 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, 900 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, 900 Series Over-Under Upper Zone B/D, Warning Lights (4), Whelen, LED, ION Wide Angle Upper Zone B/D, Warning Lights (4), Whelen, LED, LIN3 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, LINZ6 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, LINZ6 Series Split Side-By-Side

111393 111394 111395 111396 111397 111398 111399 111400 111401 111402 111403 111404 111405 111406 111407 111408 111409 111410 111411 111412 111413 111414 111415 111416 111417 111418 111419 111420 111421 111422 111423 111424 111425 111426 111427 111428 111429 111430 111332 111333 111334 111335 111336 111337 111338 111339 111340 111341 111342 111343 111344 111345 111346 111347 111348 111349 111350 111351 111352 111353 111354 111355 111356 111357 111358 111359 111360 111361 111362 111363 111364 111365 111366 111367 111368 111369 111370 111371 111372 111373 111374 111375 111376 111377 111378 111379 111380 111381 111382 111383 111384 111385 111386 111387 111388 111389 111390 111391 111392 Upper Zone B/D, Warning Lights (4), Whelen, LED, M4 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, M6 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, M6 Series Split Side-By-Side Upper Zone B/D, Warning Lights (4), Whelen, LED, M6V2 Series (Warning/Perimeter) Upper Zone B/D, Warning Lights (4), Whelen, LED, M7 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, M9 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, M9 Series Split Side-By-Side Upper Zone B/D, Warning Lights (4), Whelen, LED, M9V2 Series Upper Zone B/D, Warning Lights (4), Whelen, LED, TIR3 Series Upper Zone C, Rotating Beacons (2), Code 3, Arch LED Series Beacons, 18 LED Upper Zone C, Rotating Beacons (2), Code 3, Arch LED Series Beacons, 36 LED Upper Zone C, Rotating Beacons (2), Code 3, CL199/CL299 LED Series Upper Zone C, Rotating Beacons (2), Code 3, DuoBeam II LED Series, PriZm II LED's Upper Zone C, Rotating Beacons (2), Code 3, LSS222 Dual Stacked LED Series Upper Zone C, Rotating Beacons (2), Federal Signal, SLR Upper Zone C, Rotating Beacons (2), Whelen, ROTA-BEAM R316 Series Upper Zone C, Rotating Beacons (2), Whelen, ROTA-BEAM R316 Series Split Front-Rear, Clear Domes Upper Zone C, Rotating Beacons (2), Whelen, ROTA-BEAM R416 Series Split Front-Rear, Clear Domes Upper Zone C, Rotating/Warning Beacons (2), Federal Signal, IVP SLR with Amber IPX6 Upper Zone C, Rotating/Warning Beacons (2), Whelen, B6 LED Upper Zone C, Warning Lights (2), Code 3, LED, Perimeter 3 x 7 Upper Zone C, Warning Lights (2), Code 3, LED, Perimeter 3 x 7 Dual Color Upper Zone C, Warning Lights (2), Code 3, LED, Perimeter 4 x 6 Upper Zone C, Warning Lights (2), Code 3, LED, Perimeter 7 x 9 Upper Zone C, Warning Lights (2), Code 3, LED, PriZm II Perimeter 3 x 7, 12 LED Upper Zone C, Warning Lights (2), Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Upper Zone C, Warning Lights (2), Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Split Side-By-Side Style Upper Zone C, Warning Lights (2), Code 3, LED, PriZm II Perimeter 4 x 6, 8 LED Upper Zone C, Warning Lights (2), Code 3, LED, PriZm II Perimeter 7 x 9, 8 LED Upper Zone C, Warning Lights (2), Federal Signal, LED, MicroPulse 6 Upper Zone C, Warning Lights (2), Federal Signal, LED, QuadraFlare 6 x 4 Upper Zone C, Warning Lights (2), Federal Signal, LED, QuadraFlare 6 x 4 Split Over-Under Upper Zone C, Warning Lights (2), Federal Signal, LED, QuadraFlare 9 x 7 Upper Zone C, Warning Lights (2), PowerArc, LED, LED210 Series Upper Zone C, Warning Lights (2), PowerArc, LED, M90FK Series Upper Zone C, Warning Lights (2), PowerArc, LED, P14SM Series Upper Zone C, Warning Lights (2), Whelen, LED, 500 Series Split Side-By-Side Upper Zone C, Warning Lights (2), Whelen, LED, 500 Series TIR6 Upper Zone C, Warning Lights (2), Whelen, LED, 500 Series TIR6 Split Side-By-Side Upper Zone C, Warning Lights (2), Whelen, LED, 600 Series Upper Zone C, Warning Lights (2), Whelen, LED, 600 Series ROTA-BEAM Upper Zone C, Warning Lights (2), Whelen, LED, 600 Series Side-By-Side Upper Zone C, Warning Lights (2), Whelen, LED, 700 Series Upper Zone C, Warning Lights (2), Whelen, LED, 900 Series Upper Zone C, Warning Lights (2), Whelen, LED, 900 Series Over-Under Upper Zone C, Warning Lights (2), Whelen, LED, ION Wide Angle Upper Zone C, Warning Lights (2), Whelen, LED, LINZ6 Series Upper Zone C, Warning Lights (2), Whelen, LED, LINZ6 Series Split Side-By-Side Upper Zone C, Warning Lights (2), Whelen, LED, M4 Series Upper Zone C, Warning Lights (2), Whelen, LED, M6 Series Upper Zone C, Warning Lights (2), Whelen, LED, M6 Series Split Side-By-Side Upper Zone C, Warning Lights (2), Whelen, LED, M6V2 Series (Warning/Perimeter) Upper Zone C, Warning Lights (2), Whelen, LED, M7 Series Upper Zone C, Warning Lights (2), Whelen, LED, M9 Series Upper Zone C, Warning Lights (2), Whelen, LED, M9 Series Split Side-By-Side Upper Zone C, Warning Lights (2), Whelen, LED, M9V2 Series Upper Zone C, Warning Lights (2), Whelen, LED, Micro Edge Series Warning Lights, Additional (2), Above Driver/Officer Doors, Whelen, Mini Freedom Rota-Beam Lightbars, Model FB8*0*0P Warning Lights, Additional (2), Upper Zone C, Code 3, LED, Perimeter 3 x 7 Warning Lights, Additional (2), Upper Zone C, Code 3, LED, Perimeter 3 x 7 Dual Color Warning Lights, Additional (2), Upper Zone C, Code 3, LED, Perimeter 4 x 6 Warning Lights, Additional (2), Upper Zone C, Code 3, LED, Perimeter 7 x 9 Warning Lights, Additional (2), Upper Zone C, Code 3, LED, PriZm II Perimeter 3 x 7, 12 LED Warning Lights, Additional (2), Upper Zone C, Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Warning Lights, Additional (2), Upper Zone C, Code 3, LED, PriZm II Perimeter 4 x 6, 12 LED Split Side-By-Side Style Warning Lights, Additional (2), Upper Zone C, Code 3, LED, PriZm II Perimeter 4 x 6, 8 LED Warning Lights, Additional (2), Upper Zone C, Code 3, LED, PriZm II Perimeter 7 x 9, 8 LED Warning Lights, Additional (2), Upper Zone C, Code 3, LED, T-Rex Series Warning Lights, Additional (2), Upper Zone C, Code 3, LED, X Exterior Series, Dual Head, Side-By-Side Warning Lights, Additional (2), Upper Zone C, Code 3, LED, X Exterior Series, Dual Head, Stacked Warning Lights, Additional (2), Upper Zone C, Code 3, LED, X Exterior Series, Single Head Warning Lights, Additional (2), Upper Zone C, Federal Signal, LED, MicroPulse 6 Warning Lights, Additional (2), Upper Zone C, Federal Signal, LED, QuadraFlare 6 x 4 Warning Lights, Additional (2), Upper Zone C, Federal Signal, LED, QuadraFlare 6 x 4 Split Over-Under Warning Lights, Additional (2), Upper Zone C, Federal Signal, LED, QuadraFlare 9 x 7 Warning Lights, Additional (2), Upper Zone C, PowerArc, LED, M90FK Series Warning Lights, Additional (2), Upper Zone C, PowerArc, LED, P14SM Series Warning Lights, Additional (2), Upper Zone C, Weldon, LED, Diamondback 4 x 6 Warning Lights, Additional (2), Upper Zone C, Weldon, LED, Diamondback 4 x 6 Split (Vertical) Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 400 Series Single Level Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 500 Series Split Side-By-Side Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 500 Series TIR6 Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 500 Series TIR6 Split Side-By-Side Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 600 Series Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 600 Series ROTA-BEAM Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 600 Series Side-By-Side Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 700 Series Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 900 Series Warning Lights, Additional (2), Upper Zone C, Whelen, LED, 900 Series Over-Under Warning Lights, Additional (2), Upper Zone C, Whelen, LED, ION Wide Angle Warning Lights, Additional (2), Upper Zone C, Whelen, LED, LIN3 Series Warning Lights, Additional (2), Upper Zone C, Whelen, LED, LINZ6 Series Warning Lights, Additional (2), Upper Zone C, Whelen, LED, LINZ6 Series Split Side-By-Side Warning Lights, Additional (2), Upper Zone C, Whelen, LED, M4 Series Warning Lights, Additional (2), Upper Zone C, Whelen, LED, M6 Series Warning Lights, Additional (2), Upper Zone C, Whelen, LED, M6 Series Split Side-By-Side Warning Lights, Additional (2), Upper Zone C, Whelen, LED, M6V2 Series (Warning/Perimeter) Warning Lights, Additional (2), Upper Zone C, Whelen, LED, M7 Series Warning Lights, Additional (2), Upper Zone C, Whelen, LED, M9 Series

111493 111494 111495 111496 111497 111498 111499 111500 111501 111502 111503 111504 111505 111506 111507 111508 111509 111510 111512 111513 111514 111515 111516 111517 111518 111519 111520 111521 111522 111523 111524 111525 111526 111527 111528 111529 111530 111531 111431 111432 111433 111434 111435 111437 111438 111439 111440 111441 111442 111443 111444 111445 111446 111447 111448 111449 111450 111451 111452 111453 111454 111455 111456 111457 111458 111459 111460 111461 111462 111463 111464 111465 111466 111467 111468 111469 111470 111471 111472 111473 111474 111475 111476 111477 111478 111479 111480 111481 111482 111483 111484 111485 111486 111487 111488 111489 111490 111491 111492 Warning Lights, Additional (2), Upper Zone C, Whelen, LED, M9 Series Split Side-By-Side Warning Lights, Additional (2), Upper Zone C, Whelen, LED, TIR3 Series Pump Compartment in Body, Rear Mount Pump Compartment in Body, Side Mount, Front of Body Compartment Below Speedlays Pump Panels, Rear Mount, Controls in Driver-Side Rear Cmpt, Line-X Oper. Panel, Line-X Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Driver-Side Rear Cmpt, Line-X Oper. Panel, Painted Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Driver-Side Rear Cmpt, Line-X Oper. Panel, Stainless Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Driver-Side Rear Cmpt, Stainless Oper. Panel, Line-X Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Driver-Side Rear Cmpt, Stainless Oper. Panel, Painted Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Driver-Side Rear Cmpt, Stainless Oper. Panel, Stainless Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Officer-Side Rear Cmpt, Line-X Oper. Panel, Line-X Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Officer-Side Rear Cmpt, Line-X Oper. Panel, Painted Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Officer-Side Rear Cmpt, Line-X Oper. Panel, Stainless Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Officer-Side Rear Cmpt, Stainless Oper. Panel, Line-X Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Officer-Side Rear Cmpt, Stainless Oper. Panel, Painted Rear Panel, Bezel Package Pump Panels, Rear Mount, Controls in Officer-Side Rear Cmpt, Stainless Oper. Panel, Stainless Rear Panel, Bezel Package Pump Panel Lighting, Rear Mount, Oper. Panel Utilize Rollup Door Lights, Grote Lights (2) on Rear Panel Access Panel, Pump, in Driver's Side Rear Cmpt, Match Cmpt Finish, Compression Latches Access Panel, Pump, in Officer's Side Rear Cmpt, Match Cmpt Finish, Compression Latches Pump, Waterous, Single-Stage, 1000 GPM, CXVK, TC20 Transmission, Standard Impeller Hubs Pump, Waterous, Single-Stage, 1000 GPM, CXVK, TC20 Transmission, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 1250 GPM, CXVK, TC20 Transmission, Standard Impeller Hubs Pump, Waterous, Single-Stage, 1250 GPM, CXVK, TC20 Transmission, Flame Plated Impeller Hubs Pump, Waterous, Single-Stage, 2000 GPM, S100, TC20 Transmission, Flame Plated Impeller Hubs Anodes, OEM, Alloy, 2 Discharge, 1 Intake Pump Mounting, Rear Mounted Pump Pump Shift and Lights, Waterous, Manual Pump Shift Override at Front of Body Drains, Rear Mount Pumper, Innovative Controls, Manual Lift Handle Drains, Rear Mount Pumper, Innovative Controls, Manual Lift Handle, Class 1 Auto Drains on Pre-Connects Drains, Rear Mount Pumper, Innovative Controls, Manual Quarter-Turn Drains, Rear Mount Pumper, Innovative Controls, Manual Quarter-Turn, Class 1 Auto Drains on Pre-Connects Manifold, Waterous, Rear Mount Pumper Steamer, Rear Driver-Side, 6" MNST Steamer, Rear Center, 6" MNST Steamer, Rear Officer-Side, 6" MNST Inlet, Rear Driver-Side, 2-1/2", Fully Recessed Inlet, Rear Driver-Side, 3", Fully Recessed Inlet, Rear Officer-Side, 2-1/2", Fully Recessed Inlet, Rear Officer-Side, 3", Fully Recessed Inlet, Rear Center, 2-1/2", Fully Recessed Inlet, Rear Center, 3", Fully Recessed Discharge, Rear Driver-Side, 2-1/2", NST (250 GPM) Discharge, Rear Driver-Side, 2-1/2", NST, 3" Plumbing (250 GPM) Discharge, Rear Driver-Side, 3", NST (375 GPM) Discharge, Rear Driver-Side, 4", NST (625 GPM) Discharge, Rear Officer-Side, 2-1/2" NST (250 GPM) Discharge, Rear Officer-Side, 2-1/2", NST, 3" Plumbing (250 GPM) Discharge, Rear Officer-Side, 3", NST Discharge, Rear Officer-Side, 4" NST (625 GPM) Discharge, Rear Center, 2-1/2" NST (250 GPM) Discharge, Rear Center, 2-1/2", NST, 3" Plumbing (250 GPM) Discharge, Rear Center, 3", NST Discharge, Rear Center, 4" NST (625 GPM) Deluge, Front-Center of the Body, 3", NPT Deluge, Rear Driver-Side Corner of the Body, 3", NPT Deluge, Rear Officer-Side Corner of the Body, 3", NPT Deluge, Rear Driver-Side Corner of the Body, 3", Victaulic Deluge, Rear Officer-Side Corner of the Body, 3", Victaulic Deck Gun, Electric, TFT Typhoon, Y5-EL1A, 30' Tether Control Near Operators Panel Deck Gun, Electric, TFT Typhoon, Y5-EL1A, 30' Tether Control Near Operators Panel and Wireless Controls Crosslays, Front Bumper, Rear Mount Pumper, (2) 1-1/2" Speedlays in Lift Out Trays, Ahead of L1/R1, (2) 1-1/2" and (1) 2-1/2" Speedlays in Lift Out Trays, Ahead of L1/R1, (2) 1-1/2", Stacked Speedlays in Lift Out Trays, Enclosed L1/R1, (2) 1-1/2" and (1) 2-1/2" Speedlays in Lift Out Trays, Enclosed L1/R1, (2) 1-1/2", Side-By-Side Speedlays in Lift Out Trays, Enclosed L1/R1, (2) 1-1/2", Stacked Speedlays in Lift Out Trays, Enclosed L1/R1, (3) 1-1/2", Stacked Speedlays on Roll Out Tray, Ahead of L1/R1, (2) 1-1/2" Crosslay Cover, Hinged Bi-fold Tread Plate, Bumper Rear Deck, Bolt-On, Flat Back, Tread Plate, 13.25", Notched Center Air Outlet, 1/4" Quick Connect Female, Driver's Side Pump Panel, Check Valve, 25' of Hose in Body Cmpt (Charlotte) Air Outlet, 1/4" Quick Connect Female, Officer's Side Pump Panel Air Outlet, 1/4" Quick Connect Male, On/Off, Left Pump Panel Air Outlets, (2) 1/4" Quick Connect Female, Driver's and Officer's Side Pump Panels (Detroit) Auxiliary Steps, Grip-Strut, Two (2), Below Chassis Cab Auxiliary Steps, Grip-Strut, Four (4), Below Chassis Cab Battery Charger/Compressor, Kussmaul, Pump Plus 1200, Compartment L1 Battery Jump Start Plug, Anderson Charger Cover, Treadplate Cover For Kussmaul Pump Chassis Step Overlays, Full, Tread Plate, Generic, (2) Compartments, 4 Door Cab Chassis Step Overlays, Full, Tread Plate, International, (2) Compartments, 4 Door Cab Chassis, Interior Option, Replace Officer's Seat And Install 3rd Seat, In Extended Cab (Modified by OEM) Electrical Equipment Compartment, Behind Officer's Seat Engine Compartment LED Light Engine Compartment LED Lights, Two (2) Route Manual Moisture Ejector Cables, Chassis, Outside of Body, Terminate With 1/4 Turn Valve Flashlight, (1), Pelican, 9410L Rechargeable, Yellow Flashlights, (2), Pelican, 9410L Rechargeable, Yellow Flashlights, (3), Pelican, 9410L Rechargeable, Yellow Flashlights, (4), Pelican, 9410L Rechargeable, Yellow Flashlights, (5), Pelican, 9410L Rechargeable, Yellow Flashlights, (6), Pelican, 9410L Rechargeable, Yellow Flashlight, (1), Pelican, Big Ed Rechargeable, Yellow, 3765 Flashlights, (2), Pelican, Big Ed Rechargeable, Yellow, 3765 Flashlights, (3), Pelican, Big Ed Rechargeable, Yellow, 3765 Flashlights, (4), Pelican, Big Ed Rechargeable, Yellow, 3765 Flashlights, (5), Pelican, Big Ed Rechargeable, Yellow, 3765 Flashlights, (6), Pelican, Big Ed Rechargeable, Yellow, 3765

111593 111594 111595 111596 111597 111598 111599 111600 111601 111602 111603 111604 111605 111606 111607 111608 111609 111610 111611 111612 111613 111614 111615 111616 111617 111618 111619 111620 111621 111622 111623 111624 111625 111626 111627 111628 111629 111630 111532 111533 111534 111535 111536 111537 111538 111539 111540 111541 111542 111543 111544 111545 111546 111547 111548 111549 111550 111551 111552 111553 111554 111555 111556 111557 111558 111559 111560 111561 111562 111563 111564 111565 111566 111567 111568 111569 111570 111571 111572 111573 111574 111575 111576 111577 111578 111579 111580 111581 111582 111583 111584 111585 111586 111587 111588 111589 111590 111591 111592 Flashlight, (1), Streamlight, E-Flood LiteBox, LED, Orange, 45805, Vehicle Mount System Flashlights, (2), Streamlight, E-Flood LiteBox, LED, Orange, 45805, Vehicle Mount System Flashlights, (3), Streamlight, E-Flood LiteBox, LED, Orange, 45805, Vehicle Mount System Flashlights, (4), Streamlight, E-Flood LiteBox, LED, Orange, 45805, Vehicle Mount System Flashlights, (5), Streamlight, E-Flood LiteBox, LED, Orange, 45805, Vehicle Mount System Flashlights, (6), Streamlight, E-Flood LiteBox, LED, Orange, 45805, Vehicle Mount System Flashlight, (1), Streamlight, E-Spot LiteBox, LED, Orange, 45855, Vehicle Mount System Flashlights, (2), Streamlight, E-Spot LiteBox, LED, Orange, 45855, Vehicle Mount System Flashlights, (3), Streamlight, E-Spot LiteBox, LED, Orange, 45855, Vehicle Mount System Flashlights, (4), Streamlight, E-Spot LiteBox, LED, Orange, 45855, Vehicle Mount System Flashlights, (5), Streamlight, E-Spot LiteBox, LED, Orange, 45855, Vehicle Mount System Flashlights, (6), Streamlight, E-Spot LiteBox, LED, Orange, 45855, Vehicle Mount System Flashlight, (1), Streamlight, Firebox, Orange, 45302, Vehicle Mount System Flashlights, (2), Streamlight, Firebox, Orange, 45302, Vehicle Mount System Flashlights, (3), Streamlight, Firebox, Orange, 45302, Vehicle Mount System Flashlights, (4), Streamlight, Firebox, Orange, 45302, Vehicle Mount System Flashlights, (5), Streamlight, Firebox, Orange, 45302, Vehicle Mount System Flashlights, (6), Streamlight, Firebox, Orange, 45302, Vehicle Mount System Flashlight, (1), Streamlight, Survivor LED, Orange, 90503, with Steady Charger Flashlights, (2), Streamlight, Survivor LED, Orange, 90503, with Steady Charger Flashlights, (3), Streamlight, Survivor LED, Orange, 90503, with Steady Charger Flashlights, (4), Streamlight, Survivor LED, Orange, 90503, with Steady Charger Flashlights, (5), Streamlight, Survivor LED, Orange, 90503, with Steady Charger Flashlights, (6), Streamlight, Survivor LED, Orange, 90503, with Steady Charger Flashlight, (1), Streamlight, Survivor LED, Orange, 90509, with Fast Charger Flashlights, (2), Streamlight, Survivor LED, Orange, 90509, with Fast Charger Flashlights, (3), Streamlight, Survivor LED, Orange, 90509, with Fast Charger Flashlights, (4), Streamlight, Survivor LED, Orange, 90509, with Fast Charger Flashlights, (5), Streamlight, Survivor LED, Orange, 90509, with Fast Charger Flashlights, (6), Streamlight, Survivor LED, Orange, 90509, with Fast Charger Front Bumper Option, Chassis Supplied Recess Q2B Siren, OEM Installed, Recess Mount, Disconnect Switch Storage Well, Front Bumper, Markham, On Top of Gravel Shield, Full Width, Headlight-to-Headlight, Tread Plate Raised Cover Front Bumper Option, Hydraulic Hose Bulkhead Fittings, Driver's Side Front Bumper Extension, Chassis Supplied, OEM Supplied and Installed Line-X Tread Plate Gravel Shield Storage Well Flooring, Dri-Dek, Full Width Compartment Storage Well Flooring, Dri-Dek, (1) Storage Well Storage Well Flooring, Dri-Dek, (2) Storage Wells Storage Well Flooring, Dri-Dek, (3) Storage Wells Storage Well Flooring, Turtle Tile, Full Width Compartment Storage Well Flooring, Turtle Tile, (1) Storage Well Storage Well Flooring, Turtle Tile, (2) Storage Wells Storage Well Flooring, Turtle Tile, (3) Storage Wells Fuel Tank, 50 Gallon, Behind Rear Axles Glove Boxes, (3), Chassis Interior, Back of Engine Tunnel Battery Charger/Inverter, Kussmaul-Newmar, 1200W Battery Charger/Inverter, Vanner Lifestar, 1050W Knox Box, Customer Supplied, OEM Installed Knox Box, Customer Supplied, OEM Installed, 12V Power Accessory (USB) Dual Outlet, 12V, Battery Direct Map Console, 2-Slot (2-1/2" Binders), Abraded Map Console, 2-Slot (2-1/2" Binders), Black Line-X Map Console, 2-Slot (2-1/2" Binders), Gray Line-X Map Console, 2-Slot (2-1/2" Binders), MultiSpec to Match Cab Interior Map Console, 2-Slot (3" Binders), Abraded Map Console, 2-Slot (3" Binders), Black Line-X Map Console, 2-Slot (3" Binders), Gray Line-X Map Console, 2-Slot (3" Binders), MultiSpec to Match Cab Interior Map Console, 3-Slot (1-1/2" Binders), Abraded Map Console, 3-Slot (1-1/2" Binders), Black Line-X Map Console, 3-Slot (1-1/2" Binders), Gray Line-X Map Console, 3-Slot (1-1/2" Binders), MultiSpec to Match Cab Interior Map Console, 3-Slot (2-1/2" Binders), Abraded Map Console, 3-Slot (2-1/2" Binders), Black Line-X Map Console, 3-Slot (2-1/2" Binders), Gray Line-X Map Console, 3-Slot (2-1/2" Binders), MultiSpec to Match Cab Interior Map Console, 3-Slot (3" Binders), Abraded Map Console, 3-Slot (3" Binders), Black Line-X Map Console, 3-Slot (3" Binders), Gray Line-X Map Console, 3-Slot (3" Binders), MultiSpec to Match Cab Interior Map Console, 3-Slot (3-1/2" Binders), Sloped Dividers, Abraded Map Console, 3-Slot (3-1/2" Binders), Sloped Dividers, Black Line-X Map Console, 3-Slot (3-1/2" Binders), Sloped Dividers, Gray Line-X Map Console, 3-Slot (3-1/2" Binders), Sloped Dividers, MultiSpec to Match Cab Interior Map Console, 4-Slot (1-1/2" Binders), Abraded Map Console, 4-Slot (1-1/2" Binders), Black Line-X Map Console, 4-Slot (1-1/2" Binders), Gray Line-X Map Console, 4-Slot (1-1/2" Binders), MultiSpec to Match Cab Interior Map Console, 4-Slot (2-1/2" Binders), Abraded Map Console, 4-Slot (2-1/2" Binders), Black Line-X Map Console, 4-Slot (2-1/2" Binders), Gray Line-X Map Console, 4-Slot (2-1/2" Binders), MultiSpec to Match Cab Interior Map Console, 6-Slot (3" Binders), Abraded Map Console, 6-Slot (3" Binders), Black Line-X Map Console, 6-Slot (3" Binders), Gray Line-X Map Console, 6-Slot (3" Binders), MultiSpec to Match Cab Interior Map Console, Upper Macungie, 6-Slot (3" Binders), Small Storage Area, Hinged Lid, Gray Line-X Map Consoles, (2), 2-Slot (2" Binders), Abraded Map Consoles, (2), 2-Slot (2" Binders), Black Line-X Map Consoles, (2), 2-Slot (2" Binders), Gray Line-X Map Consoles, (2), 2-Slot (2" Binders), MultiSpec to Match Cab Interior Modify Exterior Compartment For Fire Extinguisher and (2) O2 Bottles Mounting Plate, On Top Engine Tunnel Above A/C/ Unit, Abraded Aluminum Mounting Plates, (2), Back Wall of Chassis Cab, Abraded Aluminum Mud Flap, Full-Width, Rear Brush Splash Guard Mud Flap, Full Width, Rear Refrigerator, Norcold, Dual Voltage 12V / 120V, 1.7 Cu.Ft., Model DE-0740 Relocate Cab Tilt Manual Override, To Back Wall of Pump Module Relocate Cab Tilt Pendand and Release Cable, Officer's Side Enclosed Pump Panel Relocate Chassis Supplied AC Unit

111713 111714 111716 111717 111718 111719 111720 111721 111722 111723 111724 111725 111726 111727 111728 111729 111730 111731 111732 111733 111734 111735 111736 111737 111738 111739 111740 111741 111742 111743 111744 111745 111746 111747 111748 111749 111750 111751 111631 111632 111633 111634 111635 111636 111637 111638 111639 111640 111641 111642 111643 111644 111645 111646 111647 111648 111649 111650 111651 111652 111653 111675 111676 111677 111678 111679 111680 111681 111682 111683 111684 111685 111686 111687 111688 111689 111690 111691 111692 111693 111694 111695 111696 111697 111698 111699 111700 111701 111702 111703 111704 111705 111706 111707 111708 111709 111710 111711 111712 Relocate the Chassis Lubrication System, w/Access Door, Officer's Side Pump Panel Shelf, Back of Engine Tunnel, Line-X Aluminum Storage Well, Front Bumper, Charlotte, Center (4 Rescue Tools) and Officer's Side Storage Wells, Full Tread Plate Raised Cover Storage Well, Front Bumper, Center (4 Rescue Tools) and Officer's Side Storage Wells, Full Tread Plate Raised Cover Storage Well, Front Bumper, Full Width, Headlight-to-Headlight, Tread Plate Raised Cover W/Notch Storage Well, Front Bumper, Huntersville, Center (2 Rescue Tools) and Officer's Side Hose Wells, Full Tread Plate Raised Cover Storage Well, Front Bumper, Center (2 Rescue Tools) and Officer's Side Hose Wells, Full Tread Plate Raised Cover Storage Well, Front Bumper, Center Hose Well and Officer's Side Hose Well, Headlight-to-Headlight, Tread Plate Raised Cover (Mansfield) Storage Well, Front Bumper, Full Width, Headlight-to-Headlight, Tread Plate 2-Tier Raised Cover, Built-In Hose Storage Super Auto Eject, Kussmaul, 20 Amp, 091-55-20-120, Rear Body, Driver-Side Switch Panel, Standard 12-Switch and 6-Switch, Floor Console Swivel Mount, Johnny Ray, JR-207, Chassis Interior Thermal Imaging Camera, Customer Supplied, OEM Installed, In Chassis Cab Thermal Imaging Camera, Customer Supplied, OEM Installed, In EMS Compartment Storage Well, Front Bumper, Driver's Side, Webbing Cover Storage Well, Front Bumper, Center, Webbing Cover Storage Well, Front Bumper, Officer's Side, Webbing Cover Winter Grill Cover, Vinyl, Button Snaps and Zipper OEM Chassis Preparations, Kenworth Laptop Docking Station, Customer Supplied, OEM Installed, In Chassis Cab Tool Compartments Below Walkway (UST Style), Hinged Lift-Up Tread Plate Door and LED Light, Turtle Tile Flooring Tool Compartments Below Walkway (UST Style), Hinged Lift-Up Tread Plate Door and LED Light, Dri-Dek Tile Flooring Access Panels, (2), Pump, Front Pump Module, Removable, Tread Plate, Compression Latches, Top Mounts Rear Steps and Lighting, OEM Access Ladder (Alum.) with 2-Step Drop Down, Driver's Side-Rear OEM Access Ladder (Alum.) with 2-Step Drop Down, Driver's Side-Rear, (1) Officer's Side-Rear Bolt-On Step Rear Steps and Lighting, OEM Access Ladder (Alum.) with 2-Step Drop Down, Driver's Side-Rear, (2) Officer's Side-Rear Bolt-On Steps Rear Steps and Lighting, OEM Access Ladder (Alum.) with 2-Step Drop Down, Driver's Side-Rear, (3) Officer's Side-Rear Bolt-On Steps Rear Steps and Lighting, OEM Access Ladder (Alum.) with 2-Step Drop Down, Driver's Side-Rear, (4) Officer's Side-Rear Bolt-On Steps OEM Access Ladder (Alum.) with 2-Step Drop Down, Driver's Side-Rear, (1) Officer's Side-Rear Folding Step Rear Steps and Lighting, OEM Access Ladder (Alum.) with 2-Step Drop Down, Driver's Side-Rear, (2) Officer's Side-Rear Folding Steps Rear Steps and Lighting, OEM Access Ladder (Alum.) with 2-Step Drop Down, Driver's Side-Rear, (3) Officer's Side-Rear Folding Steps Rear Steps and Lighting, OEM Access Ladder (Alum.) with 2-Step Drop Down, Driver's Side-Rear, (4) Officer's Side-Rear Folding Steps Rear Steps and Lighting, OEM Access Ladder (Alum.) with 2-Step Drop Down, Officer's Side-Rear Rear Steps and Lighting, OEM Access Ladders (Alum.), (2) with 2-Step Drop Down, Driver's Side-Rear and Officer's Side-Rear Rear Steps and Lighting, OEM Access Ladder (SS) with 2-Step Drop Down, Driver's Side-Rear OEM Access Ladder (SS) with 2-Step Drop Down, Driver's Side-Rear, (1) Officer's Side-Rear Bolt-On Step OEM Access Ladder (SS) with 2-Step Drop Down, Driver's Side-Rear, (2) Officer's Side-Rear Bolt-On Steps Rear Steps and Lighting, OEM Access Ladder (SS) with 2-Step Drop Down, Driver's Side-Rear, (3) Officer's Side-Rear Bolt-On Steps Rear Steps and Lighting, OEM Access Ladder (SS) with 2-Step Drop Down, Driver's Side-Rear, (4) Officer's Side-Rear Bolt-On Steps Rear Steps and Lighting, OEM Access Ladder (SS) with 2-Step Drop Down, Driver's Side-Rear, (1) Officer's Side-Rear Folding Step Rear Steps and Lighting, OEM Access Ladder (SS) with 2-Step Drop Down, Driver's Side-Rear, (2) Officer's Side-Rear Folding Steps Rear Steps and Lighting, OEM Access Ladder (SS) with 2-Step Drop Down, Driver's Side-Rear, (3) Officer's Side-Rear Folding Steps Rear Steps and Lighting, OEM Access Ladder (SS) with 2-Step Drop Down, Driver's Side-Rear, (4) Officer's Side-Rear Folding Steps Rear Steps and Lighting, OEM Access Ladder (SS) with 2-Step Drop Down, Officer's Side-Rear Rear Steps and Lighting, OEM Access Ladders (SS), (2) with 2-Step Drop Down, Driver's Side-Rear and Officer's Side-Rear Zico Quic-Ladder with 2-Step Drop Down, Driver's Side-Rear Zico Quic-Ladder with 2-Step Drop Down, Driver's Side-Rear, (1) Officer's Side-Rear Bolt-On Step Zico Quic-Ladder with 2-Step Drop Down, Driver's Side-Rear, (2) Officer's Side-Rear Bolt-On Steps Zico Quic-Ladder with 2-Step Drop Down, Driver's Side-Rear, (3) Officer's Side-Rear Bolt-On Steps Zico Quic-Ladder with 2-Step Drop Down, Driver's Side-Rear, (4) Officer's Side-Rear Bolt-On Steps Zico Quic-Ladder with 2-Step Drop Down, Driver's Side-Rear, (1) Officer's Side-Rear Folding Step Zico Quic-Ladder with 2-Step Drop Down, Driver's Side-Rear, (2) Officer's Side-Rear Folding Steps Rear Steps and Lighting, Zico Quic-Ladder with 2-Step Drop Down, Driver's Side-Rear, (3) Officer's Side-Rear Folding Steps Rear Steps and Lighting, Zico Quic-Ladder with 2-Step Drop Down, Driver's Side-Rear, (4) Officer's Side-Rear Folding Steps Zico Quic-Ladder with 2-Step Drop Down, Officer's Side-Rear Rear Steps and Lighting, Zico Quic-Ladders (2) with 2-Step Drop Down, Driver's Side-Rear and Officer's Side-Rear Storage Well, Front Bumper, Center (Booster Reel), Tread Plate Raised Cover Storage Well, Front Bumper, Center, Full Length Tread Plate Raised Cover Storage Well, Front Bumper, Center (2 Rescue Tools) and 2 Outboard Hydraulic Reels, Full Width, Headlight-to-Headlight, Tread Plate Raised Cover Pump, Hale, Two-Stage (PTO), 750 GPM, TBP-B Valve, 2-1/2", Akron, Manual, 8625, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector) Valve, 2-1/2", Akron, Manual, 8925, Composite Ball, Innovative Controls Push Pull Controller (Rack and Sector) Valve, 2-1/2", Elkhart, Manual, EB25-R1F, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector) Turntable Rotational Gear Cover, Officer's Side Turntable Work Lights, (3) OnScene and (1) Truck-Lite, LED Turntable Work Lights, (4) Grote LED Stabilizer 1" Auxiliary Pads (4) Above Rear Wheels In Body, Painted Door Stabilizer 1" Auxiliary Pads (2) Above Rear Wheels In Body, Painted Door Stabilizer 2" Auxiliary Pads (4) Behind Rear Wheels In Body Velcro Strap Stabilizer Cover Warning Lights (2), Federal, QuadraFlare LED, Red, Activated with Aerial Master Stabilizer Cover Warning Lights (2), Federal, QuadraFlare LED, Red, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (4), Federal, QuadraFlare LED, Red, Activated with Aerial Master Stabilizer Cover Warning Lights (4), Federal, QuadraFlare LED, Red, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (2), Weldon, Diamondback 4x6 Split LED, Red/Blue, Activated with Aerial Master Stabilizer Cover Warning Lights (2), Weldon, Diamondback 4x6 Split LED, Red/Blue, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (4), Weldon, Diamondback 4x6 Split LED, Red/Blue, Activated with Aerial Master Stabilizer Cover Warning Lights (4), Weldon, Diamondback 4x6 Split LED, Red/Blue, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (2), Whelen, 600 Series Super LED, Red with Clear Lens, Activated with Aerial Master Stabilizer Cover Warning Lights (2), Whelen, 600 Series Super LED, Red with Clear Lens, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (2), Whelen, 600 Series Super LED, Red, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (4), Whelen, 600 Series Super LED, Red with Clear Lens, Activated with Aerial Master Stabilizer Cover Warning Lights (4), Whelen, 600 Series Super LED, Red with Clear Lens, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (4), Whelen, 600 Series Super LED, Red, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (2), Whelen, M6 Super LED, Red with Clear Lens, Activated with Aerial Master Stabilizer Cover Warning Lights (2), Whelen, M6 Super LED, Red with Clear Lens, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (2), Whelen, M6 Super LED, Red, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (4), Whelen, M6 Super LED, Red with Clear Lens, Activated with Aerial Master Stabilizer Cover Warning Lights (4), Whelen, M6 Super LED, Red with Clear Lens, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (4), Whelen, M6 Super LED, Red, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (2), Whelen, M6V Super LED, Red with Clear Lens, Activated with Aerial Master Stabilizer Cover Warning Lights (2), Whelen, M6V Super LED, Red with Clear Lens, Activated with Aerial Master and Emergency Master Stabilizer Cover Warning Lights (4), Whelen, M6V Super LED, Red with Clear Lens, Activated with Aerial Master Stabilizer Cover Warning Lights (4), Whelen, M6V Super LED, Red with Clear Lens, Activated with Aerial Master and Emergency Master Stabilizer Work Lights (2), Grote LED 4" Round, Clear Stabilizer Work Lights (4), Grote LED 4" Round, Clear Stabilizer Work Lights (2), Truck-Lite 6-Diode Round LED, Clear Stabilizer Work Lights (4), Truck-Lite 6-Diode Round LED, Clear Stabilizer Work Lights (2), Whelen PAR-36 Round 6 Super LED, Clear Stabilizer Work Lights (4), Whelen PAR-36 Round 6 Super LED, Clear

111813 111814 111815 111816 111817 111818 111819 111820 111821 111822 111823 111824 111825 111826 111827 111828 111829 111830 111831 111832 111833 111834 111835 111836 111837 111838 111839 111840 111841 111842 111843 111844 111845 111846 111847 111848 111849 111850 111752 111753 111754 111755 111756 111757 111758 111759 111760 111761 111762 111763 111764 111765 111766 111767 111768 111769 111770 111771 111772 111773 111774 111775 111776 111777 111778 111779 111780 111781 111782 111783 111784 111785 111786 111787 111788 111789 111790 111791 111792 111793 111794 111795 111796 111797 111798 111799 111800 111801 111802 111803 111804 111805 111806 111807 111808 111809 111810 111811 111812 Stabilizer Work Lights (2), Whelen PAR-36 Round 12 Super LED, Clear Stabilizer Work Lights (4), Whelen PAR-36 Round 12 Super LED, Clear Ground Control System, Electric Over Hydraulic Controls, Front and Rear Stabilizers, Lower Center Rear, Horizontal, Painted Aluminum Door Ground Control System, Electric Over Hydraulic Controls, Front and Rear Stabilizers, Driver's Side Rear, Vertical, Painted Aluminum Doors Ground Control System, Electric Over Hydraulic Controls, Front and Rear Stabilizers, Officer's Side Rear, Vertical, Painted Doors Platform Control Console, Traditional, (1) Joystick, 3-Position Speed Selector Platform Equipment Storage Boxes (2) Platform Hose Storage Boxes (2), 50' of 1-3/4" Hose Platform Hose Storage Boxes (2), 50' of 2-1/2" Hose Platform Hose Storage Boxes (2), (1) 50' of 1-3/4" Hose and (1) 50' of 2-1/2" Hose Platform Equipment Storage Box and Hose Storage Box, 50' of 1-3/4" Hose Platform Equipment Storage Box and Hose Storage Box, 50' of 2-1/2" Hose Platform Warning Lights (4), Whelen, M7 Series Super LED, Red/Blue Split Hydraulic Pressure Gauge, Rear Control Station, Inn. Cntrls, 2-1/2", Brass Case Gauge, psi 0-5000 Hydraulic Pressure Gauge, Rear Control Station, Inn. Cntrls, 2-1/2", Brass Case Gauge, Dual Scale 0-5000 / 0-35000 Hydraulic Pressure Gauge, Rear Control Station, Inn. Cntrls, 2-1/2", SS Case Gauge, psi 0-5000 Hydraulic Pressure Gauge, Rear Control Station, Inn. Cntrls, 2-1/2", SS Case Gauge, Dual Scale 0-5000 / 0-35000 Flow Meter with Paddle Wheel, Class 1, Turntable Flow Meter with Paddle Wheel, FRC Insight Ultimate, 4", Turntable Flow Meter with Paddle Wheel, FRC Insight Ultimate, 5", Turntable Flow Meter with Paddle Wheel, Class 1, Pump Panel Flow Meter with Paddle Wheel, FRC Insight Ultimate, 4", Pump Panel Flow Meter Slave Display, Class 1, Turntable Flow Meter Slave Display, FRC Insight Ultimate, Turntable Flow Meter Slave Display, Akron 9300, Turntable Waterway Inlet, Officer's Side, 5" Inlet and 5" Plumbing (85' RMP/100' RMP/125') Waterway Inlet, Rear, 5" Inlet and 5" Plumbing, Check Valve (85' RMP/100' RMP/125') Chrome Bushing, 4" NPT x 4" NST - Elbow (30 Deg.) 4" FNST x 4" Storz - Storz Cap, Rocker Lug, TFT Chrome Bushing, 4" NPT x 4" NST - Elbow (30 Deg.) 4" FNST x 5" Storz - Storz Cap, Rocker Lug, TFT Chrome Bushing, 4" NPT x 5" NST - Elbow (30 Deg.) 5" FNST x 4" Storz - Storz Cap, Rocker Lug, TFT Chrome Bushing, 4" NPT x 5" NST - Elbow (30 Deg.) 5" FNST x 5" Storz - Storz Cap, Rocker Lug, TFT Chrome Bushing, 5" NPT x 5" NST - Elbow (30 Deg.) 5" FNST x 4" Storz - Storz Cap, Rocker Lug, TFT Chrome Bushing, 5" NPT x 5" NST - Elbow (30 Deg.) 5" FNST x 5" Storz - Storz Cap, Rocker Lug, TFT Chrome Bushing, 5" NPT x 6" NST - Elbow (30 Deg.) 6" FNST x 4" Storz - Storz Cap, Rocker Lug, TFT Chrome Bushing, 5" NPT x 6" NST - Elbow (30 Deg.) 6" FNST x 5" Storz - Storz Cap, Rocker Lug, TFT Chrome Bushings (2), 4" NPT x 4" NST - Elbows (2) (30 Deg.) 4" FNST x 4" Storz - Storz Caps (2), Rocker Lug, TFT Chrome Bushings (2), 4" NPT x 4" NST - Elbows (2) (30 Deg.) 4" FNST x 5" Storz - Storz Caps (2), Rocker Lug, TFT Chrome Bushings (2), 4" NPT x 5" NST - Elbows (2) (30 Deg.) 5" FNST x 4" Storz - Storz Caps (2), Rocker Lug, TFT Chrome Bushings (2), 4" NPT x 5" NST - Elbows (2) (30 Deg.) 5" FNST x 5" Storz - Storz Caps (2), Rocker Lug, TFT Chrome Bushings (2), 5" NPT x 5" NST - Elbows (2) (30 Deg.) 5" FNST x 4" Storz - Storz Caps (2), Rocker Lug, TFT Chrome Bushings (2), 5" NPT x 5" NST - Elbows (2) (30 Deg.) 5" FNST x 5" Storz - Storz Caps (2), Rocker Lug, TFT Chrome Bushings (2), 5" NPT x 6" NST - Elbows (2) (30 Deg.) 6" FNST x 4" Storz - Storz Caps (2), Rocker Lug, TFT Chrome Bushings (2), 5" NPT x 6" NST - Elbows (2) (30 Deg.) 6" FNST x 5" Storz - Storz Caps (2), Rocker Lug, TFT Aerial Monitor, Electric, Akron, StreamMaster II 3480, NO Extended Vertical Range Aerial Monitor, Electric, Akron, StreamMaster II 3480, WITH Extended Vertical Range Aerial Monitor, Electric, Akron, DeckMaster 3440 Aerial Monitor, Electric, Elkhart, Scorpion EXM 7400, NO Stow Signal Output Aerial Monitor, Electric, Elkhart, Scorpion EXM 7400, WITH Stow Signal Output Aerial Monitor, Electric, TFT, Monsoon RC Y4-E21A-P (Platforms) Aerial Monitor, Manual, Akron, Platform Monitor 3432 Aerial Monitor, Manual, TFT, Monsoon Dual Handwheel Y4-M21A-P Nozzle, Electric, Akron Akromatic 1000 GPM, 5177, 3-1/2" NH Nozzle, Electric, TFT MasterStream 1000 GPM, M-ERP1000-NN, 3-1/2" NH Nozzle, Manual, Akron Akromatic 1000 GPM, 5160, 3-1/2" NH Nozzle, Manual, Akron Akromatic 1500 GPM, 5170, 3-1/2" NH Nozzle, Manual, Elkhart X-Stream 1500 GPM, SM-1500, 3-1/2" NH Nozzle, Manual, TFT MasterStream 1000 GPM, M-R1000-NN, 3-1/2" NH Nozzle, Manual, TFT MasterStream 2000 GPM, M-R2000-NN, 3-1/2" NH Stacked Tips (Quad) and Stream Shaper, Akron, 2499, 3488 Stacked Tips (Quad), Elkhart, ST-195 Stacked Tips (Quad), TFT, YST-4NN Stacked Tips (Triple) and Stream Shaper, Elkhart, ST-195, 284A Akron Handheld Wireless Remote, 3600 Elkhart EXM Controller Kit, 7015 TFT Wireless Monitor Operation Station, YE-RF-900-D Valve Under Monitor (VUM), TFT, Electric, (1) 2-1/2" NST in C1 Port, With Drain, AKE13B111D Valve Under Monitor (VUM), TFT, Manual, (1) 2-1/2" NST in C1 Port, With Drain, AKP13B111D Adapters (2), 2-1/2" FNST x 2-1/2" MAMA - Adapters (2), 2-1/2" FAMA x 1-1/2" MNPSH - NPSH Caps (2), Chrome, South Park Adapters (2), 2-1/2" FNST x 2-1/2" MAMA - AMA Caps (2), Chrome, South Park Adapters (2), 2-1/2" FNST x 2-1/2" MBCT - Adapters (2), 2-1/2" FBCT x 1-1/2" MNPSH - NPSH Caps (2), Chrome, South Park Adapters (2), 2-1/2" FNST x 2-1/2" MBCT - BCT Caps (2), Chrome, South Park Adapters (2), 2-1/2" FNST x 2-1/2" MCSA - Adapters (2), 2-1/2" FCSA x 1-1/2" MNPSH - NPSH Caps (2), Chrome, South Park Adapters (2), 2-1/2" FNST x 2-1/2" MCSA - CSA Caps (2), Chrome, South Park Caps (2), NST, 2-1/2", Chrome, South Park Caps (2), NST, 2-1/2", Chrome, Trident Breathing Air Connections, Turntable (1) and Ladder Tip (1), Hansen Air Outlets Breathing Air Connections, Turntable (1) and Ladder Tip (1), Schroeder Air Outlets Breathing Air Connections, Turntable (1) and Front Wall of Platform (2), Hansen Air Outlets Breathing Air Connections, Turntable (1) and Front Wall of Platform (2), Schroeder Air Outlets Tracking Lights (2), 120V, On Front of Cradle, FRC LED Spectra Tracking Lights (2), 12V, On Front of Cradle, FRC LED SoBrite Tracking Lights (2), 12V, On Front of Cradle, Whelen LED Pioneer Plus (PFP1) Floodlghts Tracking Lights (2), 12V, On Front of Cradle, Whelen LED Pioneer Plus (PSP1) Spotlights Tracking Lights (2), 12V, On Front of Cradle, Whelen LED Pioneer Micro (MPPW) Tracking Lights (2), 12V, On Front of Cradle, Grote LED Trilliant Tracking Lights (2), 12V, On Front of Cradle, Collins Halogen FX-12 Tracking Lights (2), 12V, On Front of Cradle, Unity Halogen AG-R-4007 Tracking Lights (2), 12V, On Front of Cradle, Collins Halogen FX-HID Tracking Lights (2), 12V, Golight, LED Search light Tracking Lights Switch, Toggle Switch at Turntable Console Tracking Lights Switch, AL-11 Tracking Lights Switch, Dash Mount Control at Turntable Console Tip Light (1), 12V, Collins, Halogen CD-FX-12 Combination Spot/Flood Light, Switch on Lighthead Tip Light (1), 12V, Collins, Halogen CD-FX-HID Combination Spot/Flood Light, Switch on Lighthead Tip Light (1), 12V, Golight, LED Search light, Dash Mount Remote Control in Platform Tip Light (1), 12V, Grote, LED Trilliant Floodlight Tip Light (1), 12V, Grote, LED Trilliant Spotlight Tip Light (1), 12V, FRC, LED SoBrite Tip Light (1), 12V, Unity, Halogen Flood Light, Switch on Lighthead

111913 111914 111915 111916 111917 111918 111919 111920 111921 111922 111923 111924 111925 111926 111927 111928 111929 111930 111931 111932 111933 111934 111935 111936 111937 111938 111939 111940 111941 111942 111943 111944 111945 111946 111947 111948 111949 111950 111851 111852 111853 111854 111855 111856 111857 111858 111859 111860 111861 111862 111863 111864 111865 111866 111867 111868 111869 111870 111871 111872 111873 111874 111875 111876 111877 111878 111879 111880 111881 111883 111884 111885 111886 111887 111888 111889 111890 111891 111892 111893 111894 111895 111896 111897 111898 111899 111900 111901 111902 111903 111904 111905 111906 111907 111908 111909 111910 111911 111912 Tip Light (1), 12V, Unity, LED Spot/Flood Light, Switch on Lighthead Tip Light (1), 12V, Whelen, LED Micro Pioneer (MPBW) Tip Light (1), 12V, Whelen, LED PAR-36 Floodlight, Switch on Lighthead, Chrome Housing Tip Light (1), 12V, Whelen, LED PAR-36 Spotlight, Switch on Lighthead, Chrome Housing Tip Light (1), 12V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, Black Housing Tip Light (1), 12V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, White Housing Tip Light (1), 12V, Whelen, LED Pioneer Plus (PSP1) Spotlight, Switch on Lighthead Tip Lights (2), 12V, Collins, Halogen CD-FX-12 Combination Spot/Flood Light, Switch on Lighthead Tip Lights (2), 12V, Collins, Halogen CD-FX-HID Combination Spot/Flood Light, Switch on Lighthead Tip Lights (2), 12V, Grote, LED Trilliant Floodlight Tip Lights (2), 12V, Grote, LED Trilliant Spotlight Tip Lights (2), 12V, Grote, LED Trilliant (1) Spotlight and (1) Floodlight Tip Lights (2), 12V, FRC, LED SoBrite Tip Lights (2), 12V, Unity, Halogen Flood Light, Switch on Lighthead Tip Lights (2), 12V, Unity, LED Spot/Flood Light, Switch on Lighthead Tip Lights (2), 12V, Whelen, LED Micro Pioneer (MPBW) Tip Lights (2), 12V, Whelen, LED PAR-36 Floodlight, Switch on Lighthead, Chrome Housing Tip Lights (2), 12V, Whelen, LED PAR-36 Spotlight, Switch on Lighthead, Chrome Housing Tip Lights (2), 12V, Whelen, LED PAR-36 (1) Spotlight and (1) Floodlight, Switch on Lighthead, Chrome Housing Tip Lights (2), 12V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, Black Housing Tip Lights (2), 12V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, White Housing Tip Lights (2), 12V, Whelen, LED Pioneer Plus (PSP1) Spotlight, Switch on Lighthead Tip Lights (2), 12V, Whelen, LED Pioneer Plus (1) (PSP1) Spotlight and (1) (PFP1) Floodlight, Switch on Lighthead Tip Light (1), 120V, FRC, Halogen Focus 500W, Switch on Lighthead Tip Light (1), 120V, FRC, LED Spectra 20,000 Lumen, Switch on Lighthead Tip Light (1), 120V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead Tip Lights (2), 120V, FRC, Halogen Focus 500W, Switch on Lighthead Tip Lights (2), 120V, FRC, LED Spectra 20,000 Lumen, Switch on Lighthead Tip Lights (2), 120V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead Tip Lights (2), 120V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Universal Bail Mount Tip Light(s) Switch, Toggle Switch at Turntable Console Tip Light(s) Switch, AL-11 Tip Lights Locations, Front of Positional Waterway Plate, Both Sides Landing Light (1), 120V, FRC, Halogen Focus 500W Landing Light (1), 120V, Whelen, LED Pioneer Plus (PFP1) Landing Light (1), 120V, Whelen, LED Pioneer Plus (PFP2) Landing Lights (2), 120V, FRC, Halogen Focus 500W Landing Lights (2), 120V, Whelen, LED Pioneer Plus (PFP1) Landing Lights (2), 120V, Whelen, LED Pioneer Plus (PFP2) Landing Light(s) Switch, Toggle Switch at Turntable Console Landing Light(s) Switches, Toggle Switch at Turntable Console and Platform Landing Light(s) Switch, AL-11 Locator Light (1), Whelen, LED TIR3, Blue, Activated by Aerial Master Locator Light (1), Whelen, LED TIR3, Red, Activated by Aerial Master Locator Light (1), Whelen, LED Vertex, Red, Activated by Aerial Master Locator Lights (2), Whelen, LED TIR3, Blue, Activated by Aerial Master Locator Lights (2), Whelen, LED TIR3, Red, Activated by Aerial Master Locator Lights (2), Whelen, LED Vertex, Red, Activated by Aerial Master Platform Telescoping Lights (2), 120V, FRC, Halogen Optimum 750W, Switch on Lighthead Platform Telescoping Lights (2), 120V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead Platform Telescoping Lights (2), 120V, Whelen, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead Platform Tripod Lights (2), 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-15 Plug Platform Tripod Lights (2), 120V, Whelen, Tripod (Small), LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, L5-20 Plug Receptacle (1), Ladder Tip, Driver's Side, 120V, 5-15R Household Duplex Receptacle (1), Ladder Tip, Driver's Side, 120V, 5-20R Straight Blade Duplex Receptacle (1), Ladder Tip, Driver's Side, 120V, L5-15R Twistlock Duplex Receptacle (1), Ladder Tip, Driver's Side, 120V, L5-15R Twistlock Single Receptacle (1), Ladder Tip, Driver's Side, 120V, L5-20R Twistlock Single Receptacle (1), Ladder Tip, Officer's Side, 120V, 5-15R Household Duplex Receptacle (1), Ladder Tip, Officer's Side, 120V, 5-20R Straight Blade Duplex Receptacle (1), Ladder Tip, Officer's Side, 120V, L5-15R Twistlock Duplex Receptacle (1), Ladder Tip, Officer's Side, 120V, L5-15R Twistlock Single Receptacle (1), Ladder Tip, Officer's Side, 120V, L5-20R Twistlock Single Receptacle (1), Front Wall Outside of Platform, Center, 120V, L5-15R Twistlock Single Receptacle (1), Front Wall Outside of Platform, Center, 120V, L5-20R Twistlock Single Receptacle (1), Rear Wall Inside of Platform, Driver's Side, 120V, L5-15R Twistlock Single Receptacle (1), Rear Wall Inside of Platform, Driver's Side, 120V, L5-20R Twistlock Single Receptacle (1), Rear Wall Inside of Platform, Officer's Side, 120V, L5-15R Twistlock Single Receptacle (1), Rear Wall Inside of Platform, Officer's Side, 120V, L5-20R Twistlock Single Receptacles (2), Rear Wall Inside of Platform, Both Sides, 120V, L5-15R Twistlock Single Receptacles (2), Rear Wall Inside of Platform, Both Sides, 120V, L5-20R Twistlock Single Rung Lighting, Blue LED (55') Rung Lighting, Blue LED (75') Rung Lighting, Blue LED (105') Rung Lighting, Blue LED (125') Rung Lighting, Blue LED (85' RMP) Rung Lighting, Blue LED (85' MMP) Rung Lighting, Blue LED (100' RMP) Rung Lighting, Blue LED (100' MMA) Rung Lighting, Blue LED (100' MMP) Rung Lighting Switch, Toggle Switch at Turntable Console Rung Lighting Switch, AL-11 Axe Mounting Brackets (2), Fly Section, Brackets Only (Dealer/Customer Supplied Axes) Axe Mounting Brackets (2), Fly Section, WITH (1) Flat Head Axe and (1) Pick Head Axes Axe Mounting Brackets (2), Fly Section, WITH (2) Flat Head Axes Axe Mounting Brackets (2), Fly Section, WITH (2) Pick Head Axes Axe Mounting Brackets (2), In Platform, Brackets Only (Dealer/Customer Supplied Axes) Axe Mounting Brackets (2), In Platform, WITH (1) Flat Head Axe and (1) Pick Head Axes Axe Mounting Brackets (2), In Platform, WITH (2) Flat Head Axes Axe Mounting Brackets (2), In Platform, WITH (2) Pick Head Axes Halligan Mounting Bracket (1), Fly Section, Bracket Only (Dealer/Customer Supplied Halligan) Halligan Mounting Bracket (1), In Platform, Bracket Only (Dealer/Customer Supplied Halligan) Stokes Basket Storage, Officer's Side Base Section, Tread Plate Lid Stokes Basket Storage, Officer's Side Base Section, Painted Lid (55'/75') Stokes Basket Storage, Officer's Side Base Section, Painted Lid Roof Ladder Storage, Officer's Side Base Section (100' MMP) Roof Ladder Storage, Officer's Side Base Section OEM Supplied Stretcher, Ferno, Model 71 Roof Ladder Storage, Driver's Side Base Section (100' MMP)

112012 112013 112014 112015 112016 112017 112018 112019 112020 112021 112022 112023 112024 112025 112026 112027 112028 112029 112030 112031 112032 112033 112034 112035 112036 112037 112038 112039 112040 112041 112042 112043 112044 112045 112046 112047 112048 112049 111951 111952 111953 111954 111955 111956 111957 111958 111959 111960 111961 111962 111963 111964 111965 111966 111967 111968 111969 111970 111971 111972 111973 111974 111975 111976 111977 111978 111979 111980 111981 111982 111983 111984 111985 111986 111987 111988 111989 111990 111991 111992 111993 111994 111995 111996 111997 111998 111999 112000 112001 112002 112003 112004 112005 112006 112007 112008 112009 112010 112011 Roof Ladder Storage, Driver's Side Base Section Folding Attic Ladder Storage, Officer's Side Fly Section, For Duo-Safety Ladder Folding Attic Ladder Storage, Officer's Side Fly Section, For Alco-Lite Ladder Roof Ladder Storage, Officer's Side Fly Section, Special Width Ladder Roof Ladder Storage, Officer's Side Fly Section Pike Pole Storage, Officer's Side Fly Section, 6' Pole Pike Pole Storage, Officer's Side Fly Section, 8' Pole Pike Pole Storage, Officer's Side Fly Section, 10' Pole Pike Pole Storage, Officer's Side Fly Section, 12' Pole Folding Attic Ladder Storage, Driver's Side Fly Section, For Duo-Safety Ladder Folding Attic Ladder Storage, Driver's Side Fly Section, For Alco-Lite Ladder Roof Ladder Storage, Driver's Side Fly Section, Special Width Ladder Roof Ladder Storage, Driver's Side Fly Section Pike Pole Storage, Driver's Side Fly Section, 6' Pole Pike Pole Storage, Driver's Side Fly Section, 8' Pole Pike Pole Storage, Driver's Side Fly Section, 10' Pole Pike Pole Storage, Driver's Side Fly Section, 12' Pole D-ring Tie Off Points, Driver's and Officer's Sides, Aerial, (2) Front Stabilizer Panels D-ring Tie Off Points, Driver's and Officer's Sides, Aerial, (2) Rear Stabilizer Panels D-ring Tie Off Points, Driver's and Officer's Sides, Aerial, (2) Rear Wheel Wells, Recessed D-ring Tie Off Points, Driver's and Officer's Sides, Aerial, (4) Near Stabilizer Panels Turntable Control Console, Traditional, (3) Levers, On-Scene LED Light Under Lid (Platforms) System Lock Control, Red Mushroom Switch on Turntable Console System Lock Control, Foot Switch on Turntable Remote Control, 6-Function Ladder Movement Stokes Basket Storage, Officer's Side Base Section, Tread Plate Lid (55'/75') Tip Lights (2), 12V, Whelen, LED Pioneer (PFA1) Floodlight, Universal Bail Mount Tip Lights (2), 12V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Universal Bail Mount Tip Lights (2), 12V, Whelen, LED Micro Pioneer (MPBW), Universal Bail Mount Handrails, Intermediate Handrails on the Turntable Turntable Control Console, Traditional, (3) Levers, Ferrara (Platforms) Egress, Bolt-On, Ferrara (100' SHD) Egress, Bolt-On, Ferrara (125') Egress, Bolt-On, Ferrara (UT 100') Turntable Control Console, Total Vision, Ferrara (Ladders) Turntable Control Console, Total Vision, Ferrara (RM Platforms) Turntable Control Console, Total Vision, Ferrara (MM Platforms) Load Sensing System, Programmed into Total Vision Breathing Air Level and Warning System, Programmed into Total Vision Breathing Air Level and Warning System, Programmed into Total Vision, Light/Buzzer at Tip Platform Control Console, Total Vision, Ferrara Tracking Lights Switch, Total Vision Tip Light(s) Switch, Total Vision Rung Lighting Switch, Total Vision Landing Light(s) Switch, Total Vision, Ferrara Landing Light (1), 120V, FRC, LED Spectra Max 20,000 Lumens Platform Telescoping Light (1), 120V, FRC, Halogen Focus 500W, Switch on Lighthead, Driver's Side Platform Telescoping Light (1), 120V, FRC, Halogen Optimum 750W, Switch on Lighthead, Driver's Side Platform Telescoping Light (1), 120V, FRC, LED Spectra 20,000 Lumen, Switch on Lighthead, Driver's Side Platform Telescoping Light (1), 120V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, Driver's Side Platform Telescoping Light (1), 120V, Whelen, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, Driver's Side Platform Telescoping Light (1), 120V, FRC, Halogen Focus 500W, Switch on Lighthead, Officer's Side Platform Telescoping Light (1), 120V, FRC, Halogen Optimum 750W, Switch on Lighthead, Officer's Side Platform Telescoping Light (1), 120V, FRC, LED Spectra 20,000 Lumen, Switch on Lighthead, Officer's Side Platform Telescoping Light (1), 120V, Whelen, LED Pioneer Plus (PFP1) Floodlight, Switch on Lighthead, Officer's Side Platform Telescoping Light (1), 120V, Whelen, LED Pioneer Plus (PFP2) Floodlight, Switch on Lighthead, Officer's Side Swivel, 5" (Special Swivel) System Lock Control, Red Mushroom Switch on Turntable Console, Foot Switch on Turntable Tip Light (1), 120V, FRC, Halogen Focus 500W, Switch on Lighthead, Black Housing Tip Lights (2), 120V, FRC, Halogen Focus 500W, Switch on Lighthead, Black Housing EPU Switches/Lights (3), Additional, Ground Control Station/Each Stabilizer Control Box Clearance Lights, LED, Truck-Lite, Red, Pumper with Crosslays in Rear Bumper Monitor Color, Akron Red, Powder Coat, AkzoNobel Interpon PG000QF, No Texture Monitor Color, Akron Black, Sherwin Williams #F63B13 Monitor Color, Akron Lime, Fed Std 595 #13670 Monitor Color, Akron Safety Yellow, PPG# FDGH-81485 Monitor Color, Akron White, Sherwin Williams #57433 Monitor Color, Elkhart Red, RAL3003 Monitor Color, Elkhart Black, Sherwin Williams #F63B13 Monitor Color, Elkhart Lime, Sherwin Williams #13670 Monitor Color, Elkhart Safety Yellow, PPG# FDGH-81485 Monitor Color, Elkhart White, Sherwin Williams #57433 Monitor Color, TFT Silver, Powder Coat Warranty, Smeal Protection Plan, Material and Workmanship, 2 Year Warranty, Torque Box Superstructure, 15 Year Warranty, 100% V-Mux Electrical, Smeal Parts and Labor, 5 Year (Pumper) Warranty, 100% V-Mux Electrical, Smeal Parts and Labor, 5 Year (Ladder) Warranty, 100% V-Mux Electrical, Smeal Parts and Labor, 5 Year (Platform) Warranty, Parts and Labor, 3 Year (Pumper) Warranty, Parts and Labor, 3 Year (Ladder) Warranty, Parts and Labor, 3 Year (Platform) Warranty, Parts and Labor, 4 Year (Pumper) Warranty, Parts and Labor, 4 Year (Ladder) Warranty, Parts and Labor, 4 Year (Platform) Warranty, Parts and Labor, 5 Year (Pumper) Warranty, Parts and Labor, 5 Year (Ladder) Warranty, Parts and Labor, 5 Year (Platform) Warranty, Paint, 7 Year, Corrosion, 10 Year (Pumper) Warranty, Paint, 7 Year, Corrosion, 10 Year (Ladder) Warranty, Paint, 7 Year, Corrosion, 10 Year (Platform) Warranty, Paint, 10 Year, Corrosion, 10 Year (Pumper) Warranty, Paint, 10 Year, Corrosion, 10 Year (Ladder) Warranty, Paint, 10 Year, Corrosion, 10 Year (Platform) Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-400 / 0-2800 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-400 / 0-2800, Blue LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-400 / 0-2800, Red LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-400 / 0-2800, White LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-600 / 0-4200 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-600 / 0-4200, Blue LED Backlit

120022 120023 120024 120025 120026 120027 120028 120029 120030 120031 120032 120033 120034 120035 120036 120037 120038 120039 120040 120041 120042 120043 120044 120045 120046 120047 120048 120049 120050 120051 120052 120053 120054 120055 120056 120057 120058 120059 112050 112051 112052 112053 112054 112055 112056 112057 112058 112059 112060 112064 112068 112072 112073 112074 112075 112076 112077 112078 112079 112080 112081 112082 112083 112084 112085 112086 112087 112088 112089 112090 112091 112092 112093 112094 112095 112096 112097 112098 112099 112100 120000 120001 120002 120003 120004 120005 120006 120007 120008 120012 120013 120014 120015 120016 120017 120018 120019 120020 120021 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-600 / 0-4200, Red LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-600 / 0-4200, White LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, psi 0-400 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, psi 0-400, Blue LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, psi 0-400, Red LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, psi 0-400, White LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, psi 0-600 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, psi 0-600, Blue LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, psi 0-600, Red LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Brass Case Gauge (No Bezel), Orange Tip Pointer, psi 0-600, White LED Backlit Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Stainless Steel Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-400 / 0-2800 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Stainless Steel Case Gauge (No Bezel), Orange Tip Pointer, Dual Scale 0-600 / 0-4200 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Stainless Steel Case Gauge (No Bezel), Orange Tip Pointer, psi 0-400 Pressure Gauge, Inn. Cntrls, 2-1/2", Liquid Filled Stainless Steel Case Gauge (No Bezel), Orange Tip Pointer, psi 0-600 Ground Control System, Electric Over Hydraulic Controls, Rear Stabilizers, Lower Center Rear, Horizontal, Brushed Stainless Doors EMS Compartment, Rear Facing, Behind Driver's Seat, Style 4, 32" H x 20" W x 20" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Rear Facing, Behind Driver's Seat, Style 5, 38" H x 20" W x 20" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Rear Facing, Behind Driver's Seat, Style 6, 48" H x 20" W x 18" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Forward Facing, Driver's Side Rear Cab Wall, Style 4, 32" H x 20" W x 20" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Forward Facing, Driver's Side Rear Cab Wall, Style 5, 38" H x 20" W x 20" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Forward Facing, Driver's Side Rear Cab Wall, Style 6, 48" H x 20" W x 18" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Rear Facing, Behind Officer's Seat, Style 4, 32" H x 20" W x 20" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Rear Facing, Behind Officer's Seat, Style 5, 38" H x 20" W x 20" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Rear Facing, Behind Officer's Seat, Style 6, 48" H x 20" W x 18" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Forward Facing, Officer's Side Rear Cab Wall, Style 4, 32" H x 20" W x 20" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Forward Facing, Officer's Side Rear Cab Wall, Style 5, 38" H x 20" W x 20" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Forward Facing, Officer's Side Rear Cab Wall, Style 6, 48" H x 20" W x 18" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Forward Facing, Center Rear Cab Wall, Style 1, 32" H x 32" W x 16" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Forward Facing, Center Rear Cab Wall, Style 2, 38" H x 32" W x 21" D, ROM Door/Lighting, 2 Shelves EMS Compartment, Forward Facing, Center Rear Cab Wall, Style 3, 48" H x 32" W x 18" D, ROM Door/Lighting, 2 Shelves EMS FInish, Abraded, 1 EMS Compartment EMS FInish, Abraded, 2 EMS Compartments EMS FInish, Abraded, 3 EMS Compartments EMS FInish, Black Line-X, 1 EMS Compartment EMS FInish, Black Line-X, 2 EMS Compartments EMS FInish, Black Line-X, 3 EMS Compartments EMS FInish, Gray Line-X, 1 EMS Compartment EMS FInish, Gray Line-X, 2 EMS Compartments EMS FInish, Gray Line-X, 3 EMS Compartments EMS FInish, Multi-Spec to Match Cab Interior, 1 EMS Compartment EMS FInish, Multi-Spec to Match Cab Interior, 2 EMS Compartments EMS FInish, Multi-Spec to Match Cab Interior, 3 EMS Compartments Compartment Lighting, ROM, V4 LED (3) Compartment Lighting, ROM, V4 LED (4) Compartment Lighting, ROM, V4 LED (6) Compartment Lighting, ROM, V4 LED (7) Compartment Lighting, ROM, V4 LED (8) Compartment Lighting, ROM, V4 LED (9) Compartment Lighting, ROM, V4 LED (10) Compartment Lighting, ROM, V4 LED (11) Compartment Lighting, ROM, V4 LED (12) 10 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 20 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 30 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 40 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 50 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 60 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 70 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 80 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 90 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 100 - Lettering, Gold Leaf, Engine-Turned 22kt, 2" 10 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 20 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 30 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 40 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 50 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 60 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 70 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 80 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 90 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 100 - Lettering, Gold Leaf, Engine-Turned 22kt, 3" 5 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 10 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 15 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 20 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 25 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 30 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 35 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 40 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 45 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 50 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 55 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 60 - Lettering, Gold Leaf, Engine-Turned 22kt, 4" 5 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 10 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 15 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 20 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 25 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 30 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 35 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 40 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 45 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 50 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 55 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 60 - Lettering, Gold Leaf, Engine-Turned 22kt, 6" 5 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 10 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 15 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 20 - Lettering, Gold Leaf, Engine-Turned 22kt, 8"

120121 120122 120123 120124 120125 120126 120127 120128 120129 120130 120131 120132 120133 120134 120135 120136 120137 120138 120139 120140 120141 120142 120143 120144 120145 120146 120147 120148 120149 120150 120151 120152 120153 120154 120155 120156 120157 120158 120060 120061 120062 120063 120064 120065 120066 120067 120068 120069 120070 120071 120072 120073 120074 120075 120076 120077 120078 120079 120080 120081 120082 120083 120084 120085 120086 120087 120088 120089 120090 120091 120092 120093 120094 120095 120096 120097 120098 120099 120100 120101 120102 120103 120104 120105 120106 120107 120108 120109 120110 120111 120112 120113 120114 120115 120116 120117 120118 120119 120120 25 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 30 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 35 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 40 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 45 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 50 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 55 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 60 - Lettering, Gold Leaf, Engine-Turned 22kt, 8" 5 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 10 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 15 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 20 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 25 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 30 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 35 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 40 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 45 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 50 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 55 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 60 - Lettering, Gold Leaf, Engine-Turned 22kt, 10" 10 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 20 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 30 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 40 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 50 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 60 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 70 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 80 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 90 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 100 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 2" 5 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 10 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 15 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 20 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 25 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 30 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 35 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 40 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 45 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 50 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 55 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 60 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 4" 5 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 10 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 15 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 20 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 25 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 30 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 35 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 40 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 45 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 50 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 55 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 60 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 6" 5 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 10 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 15 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 20 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 25 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 30 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 35 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 40 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 45 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 50 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 55 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 60 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 8" 5 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 10 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 15 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 20 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 25 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 30 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 35 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 40 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 45 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 50 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 55 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" 60 - Lettering, Gold Leaf, Engine-Turned 23.5kt, 10" Lettering, Reflective, 18", Quantity up to 2 Lettering, Reflective, 18", Quantity up to 4 Lettering, Reflective, 18", Quantity up to 6 Lettering, Reflective, 18", Quantity up to 8 10 - Lettering, Reflective, 18" Lettering, Reflective, 18", Quantity up to 12 Lettering, Reflective, 18", Quantity up to 14 Lettering, Reflective, 18", Quantity up to 16 Lettering, Reflective, 18", Quantity up to 18 20 - Lettering, Reflective, 18" Lettering, Reflective, 18", Quantity up to 22 Lettering, Reflective, 18", Quantity up to 24 Lettering, Reflective, 18", Quantity up to 26 Lettering, Reflective, 18", Quantity up to 28 Lettering, Refl