kamber PAINT GUN MODEL 38 (5-10-15)

Add to my manuals
16 Pages

advertisement

kamber PAINT GUN MODEL 38 (5-10-15) | Manualzz

k amber PAINT GUN

PRECISION MADE IN SWITZERLAND AND DISTRIBUTED EXCLUSIVELY BY

M-B COMPANIES, INC.

IN NORTH AMERICA

Pavement Marking Equipment Divisions

Eastern Region Western Region

79 Montgomery Street

Montgomery, PA 17752

1-570-547-1621

2490 Ewald Avenue SE

Salem, OR 97302

1-503-364-2909

FOR PRICE AND DELIVERY INFORMATION

CONTACT

EAST COAST

DAVID KLINGER

1-800-233-8461 EXT 522

FAX 570-547-0619

WEST COAST

STEVE CHRISTIE

1-800-253-2909 EXT 311

FAX 503-585-0617

FOR TECHNICAL SERVICE

1-888-323-2900

CORPORATE HEADQUARTERS

1615 WISCONSIN AVENUE

NEW HOLSTEIN, WI 53061

920-898-4203

920-898-4588 FAX

M-B COMPANIES, INC.

KAMBER PAINT SPRAY GUN

MODEL 38 (5-10-15)

The Kamber Model 38 Spray Gun is a high-quality, pneumatic paint gun, manufactured under the strictest control of materials and workmanship, unequaled by any other manufacturer. The gun is designed for road marking application of all standard traffic paints, including premix. The paint line delineation on the road is excellent and, with most paint, equals that of an airless system.

TECHNICAL DATA

Atomizing air flow (non-bleeder type) with automatic internal valve.

Easily converted to bleeder type

Operating air, atomizing air and flow material are completely separate, with no gaskets

used.

Double-barreled air nozzle system is unique, resulting in very low air consumption for the paint output, which does not vary even if the exterior nozzle is worn.

By changing the exterior nozzle, spray width ranging from 2 to 12 inches can be obtained without affecting air consumption.

PAINT

The set of nozzles available allows a precise adaptation of the spray gun to all unusual or special road marking paints, cold or hot, as well as premix.

Effective air consumption at 60psi for material nozzle – 15 to 25 CFM – viscosity 90 to 110 KU.

DIMENSIONS

Length - 8 1/4”

Width - 23 ¼”

Weight - 5 lb,8 oz

WARRANTY

One year on all parts for any fault in manufacturing.

STANDARD PARTS MODEL 38-5 MODEL 38-10 MODEL 38-15

Air Nozzle 6.0 8.0-12

8.9-14

Exterior Nozzle

Line Width 4” to 8”

Line Width 8 & 9” to

12”

160-2.5 or 10-16-6

190-2.5

12-15-3 or 25-10-18

20-40-2.5

40-10-16 or 42-10-25

#44

Needle 2022-5.0 2022-6.5 2022-7.5

Effective Line

Consumption

4-8 CFM @ 40-80 psi

10-20 CFM @ 50-100 psi

15-25 CFM @ 50-100 psi

BASIC AIR NOZZLE

The basic air nozzle determines the air consumption of the gun. For the correct air consumption, the basic nozzle must correspond to the number indicated on the list of nozzles. The number engraved on the nozzle indicates the diameter of the hole. The basic air nozzle does not influence the width of spray, only the external nozzle determines the width.

OPERATING INSTRUCTIONS

1. PRESSURE:

For piston Operation – 60 psi is normal. This pressure is set at the operating air regulator.

2. PRESSURE FOR ATOMIZING AND PAINT:

This gun, due to the special construction of the air nozzle, may operate best with an atomizing pressure equal to, or lower than the pressure in the material tank or in the low pressure pumps.

The lower air pressure for atomizing, compared to the paint pressure, will still achieve a flat or even line, the larger the effective output of the gun. If the paint is thicker than normal, the atomizing air must be higher than the paint pressure.

SIZE SELECTION

1. HOSE SELECTION:

A. Operating Air Hose:

Use a 5/16” or 3/8” air hose and connect to the opening port of the paint gun

(UPPER SMALLER ¼” PORT).

B. Atomizing Air Hose:

Use a 3/8” air hose minimum and connect to the atomizing port of the paint gun

(UPPER LARGER 3/8” PORT).

NOTE: DO NOT INVERT A & B

C. Paint Hose:

For intermediate machines the paint hose should be 3/8” to ½”.

For large machines the paint hose should be ½” to ¾”.

NOTE: For greater paint output, the larger paint hose should be used. With the same pressure in the paint tank, 30% more output can be obtained by using ¾” paint hose instead of ½” hose.

Connect to the paint port of the paint gun (LOWER PORT).

2. NOZZLE SIZE SELECTION:

The size of the machine and the speed of operation, determines the size of Kamber Spray

Gun, material and air nozzle that will insure the best performance.

MODEL 38-5 Designed for intermediate size machines operating at

speeds of 4 to 8 MPH.

MODEL 38-10 Designed for truck mounted machines operating at speeds

of 6 to 12 MPH.

MODEL 38-15 Designed for truck mounted machines operating at speeds

of 10 to 16 MPH.

Before choosing the set of nozzles for the spray gun, compare the effective output of the compressor on the machine with the consumption for each size nozzle.

The nozzles described on the following page are standard parts for average viscosity material and speeds. For additional information regarding special applications, please contact you Lafarge

Road Marking representative.

KAMBER MODEL 38 PAINT GUN

LINE WIDTH CHART

GUN

MODEL

38-5

38-10

38-15

LINE WIDTH

4”

6”

8’

8”

10”

12”

4”

6”

8”

8”

10”

12”

4”

6”

8”

8”

10”

12”

NOZZLE NUMBER

160-2.5 or 10-16-9

160-2.5

160-2.5

190-2.5

190-2.5

190-2.5

12-15-3 or 25-10-18

12-15-3

12-15-3

20-40-2.5

20-40-2.5

20-40-2.5

40-10-16 OR 42-10-25

40-10-16

40-10-16

#44

#44

#44

GUN EXTERIOR NOZZLE

HEIGHT FROM ROAD

3 ½”

5”

7’

5’

6 ½”

8”

With Shroud

2 ½”

4”

5 ¾”

3”

4”

5”

4 ½”

6”

7 ½”

Without Shroud

3”

4 ½”

6”

5”

6”

7 ½”

NOTE: Height of gun may vary from chart depending on paint pressure and

atomizing pressure.

KAMBER SHROUD #3310201005

1¾”

GUN MAINTENANCE

The gun is delivered ready to use. Once a year, fill with grease, the gun’s center section. It is recommended that the special protective cover boot be reinstalled on the gun after maintenance to protect the gun’s valve parts from glass spheres.

MATERIAL NOZZLES

Always tighten material nozzle with a wrench prior to use.

NEEDLE GASKETS

The needle packing is of highly resistant Teflon material and can be expected to last an entire season. With the special key provided with the gun, tightening or loosening of the needle gaskets is accomplished without disassembling the gun.

MOVEMENT OF THE GUN (PNEUMATIC PISTON)

Never dip the gun in thinner or any other solvent. Once a week, put a few drops of oil in the upper smaller operating air port.

CLEANING THE PAINT PASSAGE IN THE GUN

VERY IMPORTANT: ALWAYS REMOVE THE EXTERIOR NOZZLE (slot nozzle)

.

For flushing of the paint passage of the gun, always remove the exterior nozzle (slot nozzle, otherwise the paint may be forced back into the air system of the gun. Maximum flushing pressure is 15 to 30 psi.

FLUSHING OF THE ATOMIZING PASSAGE OF THE GUN

BLEEDER GUN: Solvent may be flushed through the atomizing port of the paint gun while machine is in motion by using a 3-way air and solvent flushing valve.

NON-BLEEDER GUN: The paint line to the gun must be shut off, the gun turned on, and then the solvent may be flushed through the atomizing port of the gun.

“B”

10

MATERIAL

LINE

ATOMIZING AIR

M-B Companies, Inc.

Kamber Spray Gun

Disassembling Instructions

1. Remove blue plastic boot.

2. Remove material nozzle from body “A” with wrench #1.

3. Remove set screw with wrench #2.

4. Remove needle packing nut #3 with wrench #1.

5. Turn needle #5 CCW. From bottom until needle

comes free & remove needle & packing #6.

6. Remove screw #7 with wrench #8.

7. Pull body “A” directly away from body “B”

being sure not to damage gasket #9 or guide pin #10.

8. Reassemble in reverse order.

MODEL 38(5-10-15)

9

4

9

7

8

1

“A”

5

7

4

2

6

3 1.5

PNEUMATIC PAINT SPRAY GUN

REPLACEMENT PARTS LIST

MODEL 38 (5-10-15)

ITEM # PART NO. DESCRIPTION

66050002 38-5 Spray Gun Complete (Medium Machine)

66050003 38-10 Spray Gun Complete (Large Machine)

66050104 38-15 Spray Gun Complete (Large Machine)

5

7

66050038

66050039

Guide, Piston, Hard Chrome

Ring, Check for Piston Spring

9 66050040 Check

10 66050042 Nut, Counter, SST

11

12

66050051 Gasket, Copper on Valve Guide

66050036 Nut for Center Lever Arm

15

16

66050044 Spring, Center Needle

66050034 Socket, Needle Fixing with Screw

22

23

24

26

27

* *29

* *30

33

36

37

66050054 Guide for Head of Gun

66050045 Gun Head with Screw

66050083 Connection, Material (not in system)

66050220 Gasket, Teflon with Spring

66050221 Nut, Packing for Needle

66050629 Nut, Counter, Alone (part of hard chrome needle – see next page)

66050084 Head, Needle, Hard Chrome (part of hard chrome needle – see next page)

66050028 Connection, Air Intake

66050043 Ring, Valve, SST

66050035 Body Valve O-Ring

38-5

38-10

38-15

39

41

42

43

44

45

46

47

48

49

51

52

56

58

66050375 O-Ring for Valve Body

66050027 Connection, Air Intake

66050079 Connection, Air Hose

66050038 Guide, Piston Hard Chrome

Material Nozzle (Indicate Size & Item # from

Chart

Nozzle Air Basic (Indicate Size & Item # from

Chart

66050046 Nut Fixing, Basic Air Nozzle

66050056 Check Ring for Air Nozzle

66050049 Nut, Fixing for Exterior Nozzle

Nozzle, External SST Indicate Item & Size from Chart

66050048 Key to Tighten the Needle Packing Nut

(Thick) (5&10)

66050148 Key to Tighten the Needle Packing Nut (Thin)

(15)

Wrench (5)

Wrench (10&15)

1120201002 Rod, Gun Mount

73290421 Adapter 3/8” x ¼”

ITEM #

30

44

45

30

44

45

30

44

45

PART #

66050068

66050069

66050012

DESCRIPTION

66050070 Hard Chrome Needle 5.0 **

Material Nozzle 4.5

Basic Air Nozzle 6.0

66050010 Hard Chrome Needle 6.5 **

66050011 Material Nozzle 6.0

Basic Air Nozzle 8.0-12

66050063 Hard Chrome Needle 7.5 **

66050065 Material Nozzle 6.8

66050064 Basic Air Nozzle 8.9-14

ITEM NO

49

49

PART NO

66050058

66050013

KAMBER 38 GUN

(5-10-15)

EXTERIOR NOZZLES

DESCRIPTION

160-2 OR 8.18-2

12-15-3 OR 25-10-18 (38-10 ) CAN BE USED ON 38-15

49

49

49

66050062

66050066

66050074

300-2 OR 23-20-40

175-3.5 OR 41-14-25

42-10-25 (38-15 External Nozzle)

ITEM #

*2

*3

*6

PART #

SPARE PARTS KIT

PNUEMATIC PAINT SPRAY GUN

MODEL 38 (5-10-15)

DESCRIPTION

66050008*

66050009

66050020

66050018

Repair Kit – Common Repairs

Repair Kit – Complete with Socket

7mm Diameter Filter (4 Pcs) Netting Filter

Ring Graphite for Guide Valve

66050023 Gasket, Nylon (for Guide Valve between 5 & 7)

11

12

*13

*14

15

*17

66050051

66050036

66050052

66050022

66050044

66050026

Gasket Copper (on Guide Valve, Between 10 & 19)

Nut, 12mm for Center Lever Arm

Gasket, Copper (2 pcs Between 12 and Body)

O-Ring for Center Lever Arm

Spring, Center Needle

Screw, Check for Needle M3-3

*21

*22

25

*26

*27

66050021

66050054

66050055

66050220

66050221

Gasket, Nylon (between the Body and Head)

Guide for Head of Gun

Screw, SST to Fasten Head to Gun

Needle Packing, Complete Teflon, Graphite

Nut, Needle Packing

*35

36

66050024

66050043

Ring, Nylon, Between 33 and 37

Valve Ball, 10mm Diameter Stainless Steel

*38

40

66050025

66050041

O-Ring for Valve Ball #34

Guide Valve 34mm Long

(*) These part ONLY are included in the COMMON REPAIR KIT

• All Parts on page are included in COMPLETE REPAIR KIT

OPERATING

AIR

MATERIAL

LINE

ATOMIZING AIR

TO CHANGE TO

BLEEDER GUN

REMOVE BALL CHECK

OR

INSTALL FOR

NON-BLEEDER

KAMBER PAINT

GUN

M-B Companies, Inc.

Administration

1615 Wisconsin Avenue

P.O. Box 200

New Holstein, WI 53061

Phone: 800-558-5800

FAX: 920-898-4588

Pavement Marking Equipment Divisions

EAST COAST DIVISION WEST COAST DIVISION

79 Montgomery Street

Montgomery, PA 17752

2490 Ewald S.E.

Salem, OR 97302

Phone: 888-323-2900

FAX: 570-547-1629

Phone: 800-253-2909

FAX: 503-370-4389

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement