ChamFlex ® Catalog

ChamFlex ® Catalog
PO Box 22700 ~ Rochester, NY 14692
Phone: (585) 427-7780 ~ Fax (585) 427-2429
www.chamflex.com
www.chamberlinrubber.com
Revision Date: 10/2015
TABLE OF CONTENTS
Page Number
5
7
10
Advantages of ChamFlex® Hose Assemblies and Kits
Hose Assemblies
ChamFlex® Single Hose Assembly
UL-94 VO Rating Information
All Metal Stainless Steel Braided Hose
11
17
20
Automatic Balance Hose Kits
Model AC Circuit Sentry Hose Kits
Model AM Flo-Setter Hose Kits
Siemens PICV Hose Kits
22
24
26
Manual Balance Hose Kits
Model MC Circuit Setter Hose Kits
Ball Valve Hose Kits
Model MV (Venturi/Ball Valve Combination) Hose Kits
4
30
32
34
36
38
40
41
42
43
44
45
Components Kit Index
Strainers
Model UBY Combination Ball Valve & Strainer
Ball Valves
CR 1000 Series PT Port Brass Ball Valve
Model UBV Shut-Off Valve
USA 9101 Series Forged Brass Ball Valve
Unions
Model UA - Union Accessory
ATC Valves & Actuators
ATC Zone Valves and Actuators
ATC Ball Valves and Actuators
Bellimo 2.5” ActuatorPICV
Siemens PICV Actuator
Condensate Hose
ChamFlex® Brass Sweat-Hose Adapter
PO Box 22700 ~ Rochester, NY 14692
Phone: (585) 427-7780 ~ Fax (585) 427-2429
www.chamflex.com
Revision Date: 10/2015
2
TABLE OF CONTENTS
Page Number
ChamFlex® Brass Sweat-Hose Adapter
ChamFlex® Installation Instructions
46
47
48
50
51
52
54
56
57
58
59
60
ChamFlex® Single Hose Assembly
All Metal Stainless Steel Braided Hose
Valve Installation, Operation & Service Instructions
Model AC Circuit Sentry
Model AM Flo-Setter
Siemens PICV
Model MC Circuit Setter
Ball Valve
Model MV
Model UBY
Abbreviations Index
Chamberlin Rubber Company, Inc. Line Card
PO Box 22700 ~ Rochester, NY 14692
Phone: (585) 427-7780 ~ Fax (585) 427-2429
www.chamflex.com
Revision Date: 10/2015
3
4
Advantages of ChamFlex® Hose Assemblies and Kits

ChamFlex® plated steel fittings and adapters reduce the possibility of overtorquing, a
common problem with brass and other soft metals.

ChamFlex® hose fittings have a washer-less design, seating metal against metal to reduce
the chance of leaks.

ChamFlex® tube compound has been tested to, and awarded, a UL-94 VO fire safety
rating.

ChamFlex® patented process of our special tube bonded to the stainless steel braiding
minimizes the possibility of hose kinking during installation, provides a better bend radius
and enhances water flow capabilities.

ChamFlex® hose assemblies come with the thread sealant already applied. This saves
contractors time on installation.

ChamFlex® hose assemblies and hose kits comply with requirements for both the “Buy
American Act” and for funds appropriated under the “American Recovery and
Reinvestment Act” of 2009.

ChamFlex® hose assemblies are custom-made at our manufacturing facility in Rochester,
New York to meet customer specifications. Minimum length for 1/2” and 3/4” hoses is six
inches with one inch increments. Minimum length for 1” and 1 1/4” is nine inches with
one inch increments.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
5
ChamFlex®
Single Hose Assembly
Chamberlin Rubber Company, Inc. provides you with superior fire retardant hose assemblies of
unparalleled quality and integrity, designed specifically for hydronic heating and cooling systems.
ChamFlex® is a fire rated hose with fixed male pipe thread on one end and swivel with male pipe
adapter on the other end. Our tube compound has been tested to, and awarded, a UL-94 VO fire
rating, the highest standard in the industry. The patented process, which bonds the inner tube to a
stainless steel wire outer braid minimizes the possibility of the hose assembly kinking during
installation. Assemblies for 1/2” and 3/4” hoses are available in a minimum length of six inches with
increases of one inch. Minimum length for 1” and 1 1/4” hose is nine inches with one inch increments.
In short—ChamFlex® provides you a hose with a long life of trouble-free service.
ChamFlex® Hose Specifications:
Braid:
Tube Component:
Fittings & Adapters:
Temperature Range:
Ratings:
302/304 Stainless Steel
EPTF—Santoprene
Plated Steel
-40o F to 212o F
UL-94 VO Fire Rating
ChamFlex® ChamFlex® ChamFlex® ChamFlex®
1/2” Hose
3/4” Hose
1” Hose
1 1/4” Hose
Working Pressure
400 PSI
400 PSI
500 PSI
400 PSI
Burst Pressure
1600 PSI
1600 PSI
2000 PSI
1600 PSI
Minimum Bend Radius
2.5”
4”
5.5”
10”
Hose O.D. (approx.)
.700”
.975”
1.245”
1.58”
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
ChamFlex® Single Hose Assembly
6
ChamFlex® hose: Fixed End x Swivel End w/ JIC Adapter
ChamFlex® hose: Swivel End x Swivel End w/ JIC Adapters
Hose Sizes:
Hose Lengths:
1/2” to 1-1/4”
Standard:
12”, 18”, 24”, 36” and 48”
Custom:
1/2” & 3/4” - Minimum length: 6” with 1” increments.
1” & 1-1/4” - Minimum length: 9” with 1” increments.
Inner Tube:
EPTF - Santoprene with UL-94 VO Fire Rating
Outer Braid:
302/304 Stainless Steel
Fittings & Adapters:
Plated Steel
Hose/Adapter Connection: All Metal JIC Flare Connection
Fixed End Fitting:
MNPT
Swivel End Fittings:
MNPT, FSWT, FNPT
Delivery:
5 days for Fixed x Swivel MNTP
10-15 days for other adapters, double swivel end hoses and custom lengths.
NOTE: Delivery based upon normal backlog and may vary by order.
ChamFlex® Chemical Compatibility:
For general compatibility inquiries, Chamberlin utilizes a chemical resistance guide for elastomers. This guide
contains over 1000 listings and their general compatibility with our specific and unique tube component. Of
course, compatibility varies with temperature and concentration, therefore the listings within this guide may be
more general than the request. Actual compatibility can only be determined by the end user through testing
under all extreme conditions and factors. The information below is offered only as a guide.
Ethylene Glycol:
‘A’ Rating to 70° F
Propylene Glycol:
‘A’ Rating to 70°F
Methanol:
‘A’ Rating to 70°F; +1% vol., 7 days, 70°F
Ethanol:
‘A’ Rating to 70°F
WARNING: “Flux and solder drips have been found to weaken the stainless steel braiding on Chamflex® Hose
Assemblies which could lead to deterioration of the inner tube component causing ‘ballooning’ and eventual failure.
Chamflex® Hose Assemblies must be shielded with appropriate fire resistance materials or if possible, removed from
service if soldering, welding, or brazing is to occur in areas above or adjacent to said assemblies. Chamberlin Rubber Company, Inc. will not be responsible for failed hose assemblies and/or subsequent damage that occurred by
failing to follow the provided Installation Instructions (and warnings) as well as the Safety Guide.”
NOTE: Be sure that the exterior of the hose does not come into contact with substances not compatible with
302/304 stainless steel, including (but not limited to) any substances that contain chlorides. Chlorides have been
found to cause stress corrosion cracking of the stainless steel braid and eventual failure.
WARNING: To insure proper installation, this hose assembly must be installed according to instructions included with
shipment. Instructions are also available online at www.chamblerinrubber.com.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
7
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
8
Specification Comparison of UL-94 VO and ASTM E 84
UL-94 VO
ChamFlex® fire-retardant hose assemblies have a tube compound that is recognized and certified by Underwriters Laboratories to flammability specification UL-94 VO under yellow card listing QMFZ2.E80017.
UL-94 is a vertical burn test that is used widely for rubber and plastic materials that are used mostly in
electrical/electronic devices. In this test five vertically mounted samples are exposed to two successive
ten-second bottom ignitions from a 3/4” Bunsen flame. Flame resistance is then classified according to;
1. The time for the flame to self-extinguish.
2. The duration of the afterglow.
The VO rating of the ChamFlex® tube compound is the highest rating under the UL-94 test which means:
A) The extinguishment time (for each sample) was 0—10 seconds.
B) The total combustion time (for each sample) feel between 0—50 seconds.
C) The afterglow time was 0—30 seconds per sample.
D) There were no flaming drips.
E) No burning occurred up to the holding clamps.
ASTM E84
Chamberlin’s competitors also offer fire retardant hose assemblies. These competitors normally publish
fire retardant ratings to an ASTM E84 testing method. This method employs the use of a Steiner Tunnel
and is similar to UL 723, NFPA 255, UBC 42-1, CAN/ULC S-102 and ANSI 2.5. The purpose of this tunnel
test method is to determine the relative burning behavior of materials by observing the flame spread
along the surface of the development measurements of building materials with that of select grade red
oak flooring and inorganic reinforced cement board surfaces under specific fire exposure conditions.
This test method is intended for the test of flat building material specimens and not piping or hose
products.
The ASTM E84 test requires that a nominal twenty-four foot long by eighteen inch wide area is covered
by the test specimen material and is tested over a ten minute duration while flame spread over its
surface and development of the resulting smoke are measured and recorded. The test results are
computed relative to a red oak specimen (which has a rating of 100) and inorganic reinforced cement
board (which has a zero rating) with the results expressed as “Flame Spread” and “Smoke Developed”
indices. Although not a requirements of the current ASTM E84 test, “Fuel Contribution” (as calculated in
accordance with ASTM E84—1975) may also be one of the expressed results.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
9
In 1978, the “Fuel Contribution Index” was deleted from the method since it was recognized that the
vale did not provide a valid measurement of fuel contribution.
Materials are not approved or classified as a result of this test. However, building codes, such as the
Uniform Building Code, have requirements dependent on building types, occupancy, etc. The building
code having jurisdiction in the location that a tested material is to be used will determine the compliance
of the test results. It is our understanding that some of these codes require;
* A flame spread rating of 25 or less.
* A fuel contribution rating of 25 or less (if an old code).
* A smoke density rating of 50 or less.
Because the ASTM E84 test is intended for flat specimens (and not hose products) most of ChamFlex®
competitors have published their product’s fire ratings based upon a modified ASTM E84 testing
procedure. NOTE: In order to verify this, Chamberlin Rubber Company, Inc. recommends that you request
a copy of the test report along with the results from the manufacturer.
Based upon the competitor’s test reports we have seen these modifications to the ASTM E84 test
compromised the best by;
* Not testing a homogeneous specimen (a metal braid over a rubber or thermoplastic tube com
pound with couplings attached).
* Not testing produce covering the required test area (a nominal length of twenty-four feet and a
width of twenty inches).
* Conducting the test with water flowing through the hose prior to and during the test.
The following statements were also observed in the competitor’s test reports that we have seen.
“This was an experimental test in that the water flow through the armored (braided) hose was maintained during the test and the ASTM E84 test method does not address such and arrangement.”
“The braided hose (specimen tested) would be expected to perform differently at less than full water
flow during the test.”
Summary
Rather than having a “modified” ASTM E84 test performed on ChamFlex® hose assemblies Chamberlin
Rubber Company, Inc. feels that the UL-94 VO test is currently more readily acceptable and gives a better
indication of a fire retardant product.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
10
All Metal Stainless Steel Braided
Single Hose Assembly
Chamberlin All Metal Stainless Steel Assembly with Union End
Hose Sizes:
Hose Lengths:
1-1/2” to 2”
Standard:
12”, 18”, 24”, 36”
Custom:
Minimum length: 12” with 1” increments.
Inner Tube:
321L/316L Stainless Steel
Outer Braid:
304L Stainless Steel
Fittings:
Iron/Carbon Steel
Fixed End Fittings:
MNPT
Union End Fittings:
MNPT
Working Pressure:
300 psi
Burst Pressure:
1200 psi
Minimum Bend Radius:
1-1/2” - 11.75”
2” - 12.55”
Temperature Rating:
-20oF to 800oF
Delivery:
10-15 days for standard lengths.
15-20 days for custom lengths.
NOTE: Delivery based upon normal backlog and may vary by order.
WARNING: “Flux and solder drips have been found to weaken the stainless steel braiding on Chamflex® Hose
Assemblies which could lead to deterioration of the inner tube component causing ‘ballooning’ and eventual failure.
Chamflex® Hose Assemblies must be shielded with appropriate fire resistance materials or if possible, removed from
service if soldering, welding, or brazing is to occur in areas above or adjacent to said assemblies. Chamberlin
Rubber Company, Inc. will not be responsible for failed hose assemblies and/or subsequent damage that occurred
by failing to follow the provided Installation Instructions (and warnings) as well as the Safety Guide.”
NOTE: Be sure that the exterior of the hose does not come into contact with substances not compatible with
304 L stainless steel, including (but not limited to) any substances that contain chlorides. Chlorides have been
found to cause stress corrosion cracking of the stainless steel braid and eventual failure.
WARNING: To insure proper installation, this hose assembly must be installed according to instructions
included with shipment. Instructions are also available online at www.chamblerinrubber.com.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Model AC Circuit Sentry Automatic Balance Hose Kits
11
Return
COIL
Hose Kit #2
(or)
Hose Kit #3
Balance Type:
Body Design:
Body:
Ball:
O-Rings:
Max. Working Pressure:
Balance Cartridge
A & B Body:
C Body:
Spring:
Diaphragm:
Min. psid:
Max. psid:
Supply
Automatic Flow Limiting Valve with internal fixed flow cartridge
Brass Valve w/integrated isolation/shut-off, PT’s, Union End on inlet side
Brass
Chrome Plated Brass
EPDM
400 psig
Brass 36000
Stainless Steel
Stainless Steel
EPDM
Varies with size/cartridge
60
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
2.5 Model AC Circuit Sentry Automatic Balance Hose Kits
Return
COIL
Hose Kit #2
(or)
Hose Kit #3
Balance Type:
Body Design:
Body:
Ball:
O-Rings:
Max. Working Pressure:
Balance Cartridge:
Spring:
Diaphragm:
Min. psid:
Max. psid:
Cartridge Accuracy:
Supply
Automatic Flow Limiting Valve with internal fixed flow cartridge
Brass Ball Valve + Model AC with PTs, union end on inlet side
Brass
Chrome Plated Brass
EPDM
400 psig
304 Stainless Steel
Stainless Steel
Reinforced EPDM
Varies with size/cartridge
60
+/- 5%
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
12
Model AC Circuit Sentry Automatic Balance Valve
Flow Rates/Minimum PSID
"A" Body (1/2", 3/4", 1")
Flow Rate
Min. ∆P
0.33
1.2
0.5
1.5
1
1.7
1.5
1.9
1.75
1.9
2
2
2.5
2
3
2
3.5
2.3
4
3
4.5
3.2
5
3.2
5.5
3.3
6
3.3
6.5
3.3
7
3.3
7.5
3.5
8
3.5
9
3.6
10
3.8
11
4
12
7.3
13
7.3
14
7.3
"B" Body (1", 1-1/4", 1-1/2", 2")
Flow Rate
Min. ∆P
5
1.7
6
1.9
7
2
8
2
9
2.3
10
2.5
11
2.6
12
2.8
13
2.9
14
3
15
3.2
16
2.9
17
3
18
3
19
3
20
3.2
21
3.2
22
3.3
24
3.5
26
3.6
28
3.8
30
3.9
32
4.1
34
4.4
36
4.5
38
4.8
40
4.9
42
5.2
44
5.5
46
5.8
48
6.1
50
6.4
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
"C" Body (1-1/2", 2")
Flow Rate
Min. ∆P
15
1.9
20
2
25
2
30
2
35
2.2
40
2.5
45
2.8
50
3.2
55
3.3
60
3.5
65
3.9
70
4.2
75
4.9
80
4.9
85
5.1
90
5.2
95
5.2
100
5.2
105
5.2
110
5.4
120
5.5
130
5.7
140
5.8
150
5.8
13
Model AC Circuit Sentry Automatic Balance Valve
Note: GPMs are rounded up to the next available GPM unless otherwise specified.
Note: GPMs are rounded up to the next available GPM unless otherwise specified.
Note: GPMs are rounded up to the next available GPM unless otherwise specified.
Note: GPMs are rounded up to the next available GPM unless otherwise specified.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
14
15
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
16
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Model AM Flo-Setter Automatic Balance Hose Kits
17
Return
COIL
(or)
Supply
Balance Type:
Body Design:
Body:
Spring:
Diaphragm:
O-Rings:
Max. Working Pressure:
Min. psid:
Max. psid:
Automatic Flow Limiting Valve externally adjustable flow setting capability.
Brass Valve + Model AM w/PT’s, External GPM dial
Brass
Stainless Steel
HNBR
EPDM
290 psig
Varies with GPM setting
60
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Model AM Flo-Setter Automatic Balance Hose Kits
Flow Rates/Minimum PSID
Flow Rate
0.18
0.5
1
1.5
2
2.5
3
3.5
4
4.5
4.54
1/2"
Min.∆P
2.32
2.4
2.47
2.56
2.62
2.7
2.77
2.85
2.9
2.97
3.2
Setting
Min.
0.5
1
1.5
2
2.5
3
3.5
4
4.5
Max.
Flow Rate
0.31
1
2
3
4
5
6
7
8.15
3/4"
Min.∆P
1.74
2
2.25
2.5
2.75
2.95
3.2
3.35
3.77
Setting
Min.
1
2
3
4
5
6
7
Max.
Flow Rate
0.44
1
2
3
4
5
6
7
8
9
10
10.35
1"
Min.∆P
1.74
1.9
2.1
2.35
2.5
2.75
3
3.2
3.4
3.65
4
4.35
Setting
Min.
1
2
3
4
5
6
7
8
9
10
Max.
Flow Rate
0.88
2
4
6
8
10
12
14
16
18
20
21.13
1-1/4"
Min.∆P
2.03
2.2
2.38
2.6
2.75
3
3.2
3.38
3.6
3.75
4
4.32
Setting
Min.
2
4
6
8
10
12
14
16
18
20
Max.
Flow Rate
1.76
5
10
15
20
25
30
32.76
1-1/2"
Min.∆P
2.18
2.5
2.8
3.2
3.55
3.88
4.25
4.64
Setting
Min.
5
10
15
20
25
30
Max.
Flow Rate
2.2
5
10
15
20
25
30
35
40
45.46
2"
Min.∆P
2.47
2.6
3.95
3.25
3.55
3.95
4.25
4.6
5
5.5
Setting
Min.
5
10
15
20
25
30
35
40
Max.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
18
19
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Siemens PICV Automatic Balance Hose Kits
20
Return
COIL
(or)
Supply
Balance Type:
Body Design:
Body:
Spring:
Close Off:
Flow Characteristic:
Min. psid:
Max. psid:
Actuators:
PICV with adjustable max. flow setting & optional 3 Pt. floating
or 0-10Vdc Actuator
Brass valve + PICV w/PT’s, GPM dial.
Brass - ANSI 250 rating
Stainless Steel
1/2” & 3/4” Normally Open - 200 psi/ANSI Class IV,
1/2” to 1-1/4” Normally Closed - 45 psi/ANSI Class IV,
1-1/2” & Normally Closed - 50 psi/ANSI Class III
2-way, Linear
varies with gpm setting
58
Spring Return (Fail Safe): 24 volt 3 point floating or 24 volt 0-10Vdc
Non-Spring Return (Fail-in-Place): 24 volt 3 point floating or 24 volt 0-10Vdc
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Siemens PICV Automatic Balance Hose Kits
Flow Rates/Minimum PSID
Valve
-04300
-04310
Valve
-04301
-04311
Valve
-04302
-04312
Valve
-04303
Valve
-04304
Valve
-04305
Valve
-04306
Valve
-04307
21
Action
Norm. Closed
Norm. Open
1/2" L
GPM Range
.3 - 2.7
.2 - .9
Min P
2.3
2.5
Max.
58
58
P
Action
Norm. Closed
Norm. Open
1/2” H
GPM Range
1.0 - 7.5
.5 - 2.5
Min P
2.6
3
Max.
58
58
P
Action
Norm. Closed
Norm. Open
3/4” L
GPM Range
.5 - 4.5
1.0 - 5.8
Min P
2.3
3,5
Max.
58
58
P
Action
Norm. Closed
3/4” H
GPM Range
1.0 - 8.9
Min P
3.2
Max.
58
P
Action
Norm. Closed
1”
GPM Range
1.0 - 8.9
Min P
3.2
Max.
58
P
Action
Norm. Closed
1-1/4”
GPM Range
2.5 - 13.2
Min P
2.6
Max.
58
P
Action
Norm. Closed
1-1/2”
GPM Range
10.0 - 31.0
Min P
3.8
Max.
58
P
Action
Norm. Closed
2”
GPM Range
11.0 - 37.0
Min P
4.6
Max.
58
P
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Model MC Circuit Setter Manual Balance Hose Kits
22
Return
COIL
Hose
HoseKit
Kit#4
#4
(or)
Hose Kit #5
Balance Type:
Body Design:
Body:
Ball:
O-Rings:
Max. Working Pressure:
Required Pipe Diameters:
Variable Cv Manual Balance with dial setting.
Brass w/ dial control, PT’s, Union End on inlet side.
Brass
Brass
EPDM
300 psig
(3) Upstream, (1) Downstream
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Supply
23
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Ball Valve Manual Balance Hose Kits
24
Return
COIL
Hose Kit #1
(or)
Hose Kit #6
Balance Type:
Body Design:
Body:
Ball:
Stem
O-Rings:
Stem Packing:
Seat:
Handle:
Working Pressure:
Manual
Full Port Ball Valve w/PT & Memory Stop
Brass
Chrome Plated Brass
Brass
BUNA-N
PTFE
PTFE
Zinc Plated Steel w/ Plastic Coating
600 psig
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Supply
25
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Model MV (Venturi) Manual Balance Hose Kits
26
Return
COIL
(or)
Supply
Balance Type:
Body Design:
Body:
Ball:
Stem:
O-Rings:
Seal:
Handle:
Working Pressure:
Manual Venturi (fixed Cv)
Venturi/Ball Valve combination with PTs, union end on inlet.
Brass
Chrome Plated Brass
Explosion Proof
EPDM
Teflon
Chrome Plated Steel
400 psig
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
27
Model MV (Venturi) Manual Balance Valve
WARNING: To insure proper installation this product must be installed in conformance with applicable
building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
28
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
29
Components Index
Chamberlin Rubber Company, Inc. also supplies additional valves and accessories
that can be used as either substitutions or additions to the established hose kits.





Strainers
Ball Valves
Unions
ATC Zone Valves and Actuators
ATC Ball Valves and Actuators
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Model UBY Combination Ball Valve & Strainer (1/2” - 2”)
Model UBY Combination Ball Valve & Strainer
Body:
Ball:
Ball Seal:
Stem:
O-Rings:
Strainer:
Brass
Full Port Chrome Plated
PTFE
Stainless Steel Explosion Proof
EPDM
20 Mesh Stainless Steel
Maximum Working Pressure:
Maximum Operating Temp:
400 psig
-4oF to 250oF
Note: For a 2-1/2” kit a 2” UBY is supplied with a
2 -1/2” NPT expanding coupler.
WARNING: To insure proper installation this product must be installed in conformance with applicable
building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
30
31
WARNING: To insure proper installation this product must be installed in conformance with applicable
building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Ball Valve (1/2” - 2”)
32
Ball Valve Manual Balance Valve
Balance Type:
Body Design:
Body:
Ball:
Stem
O-Rings:
Stem Packing:
Seat:
Handle:
Working Pressure:
Manual
Full Port Ball Valve w/PT Memory Stop Optional
Brass
Chrome Plated Brass
Brass
BUNA-N
PTFE
PTFE
Zinc Plated Steel w/ Plastic Coating
600 psig
WARNING: To insure proper installation this product must be installed in conformance with applicable
building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
CR 1000 Series PT Port Forged Brass Ball Valve
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
33
Model UBV Shut-Off Valve (1/2” - 2”)
Model UBV Shut-Off Valve
Body:
Ball:
Ball Seal:
Stem:
O-Rings:
Handle:
Taps:
C37000 Brass
Chrome Plated
Teflon®
Explosion Proof
EPDM
Chrome Plated Steel w/ Plastic Cover
Three Total 1/4” NPT
- 1 Plugged - 1 Drain Valve - 1Pressure/Temperature Port
Maximum Working Temperature:
Temperature Range:
400 psig
-4o F to 250o F
WARNING: To insure proper installation this product must be installed in conformance with applicable
building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
34
35
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
USA 9101 Series Forged Brass Ball Valve (1/2” - 2”)
USA 9101 Series Forged Brass Ball Valve
Body:
End Cap:
Ball:
Seat:
Handle:
Stem:
Gland Nut:
Stem Packing:
Lock Washer:
Nut:
O-Ring:
Brass
Brass
Brass, Chrome Plated
PTFE
Zinc Plated Steel, Plasticoated
Brass
Brass
PTFE
Zinc Plated Steel
Zinc Plated Steel
Buna-N
WARNING: To insure proper installation this product must be installed in conformance with applicable
building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
36
37
USA 9101 Series Forged Brass Ball Valve
WARNING: To insure proper installation this product must be installed in conformance with applicable
building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Model UA - Union Accessory (1/2” - 2”)
Model UA - Union Accessory
Body:
Taps:
O-Rings:
C37000 Brass
Two 1/4” NPT spaced 90o apart
EPDM
Maximum Working Temperature:
Temperature Range:
400 psig
-4o F to 250o F
WARNING: To insure proper installation this product must be installed in conformance with applicable
building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
38
39
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
ATC Zone Valves
40
2-Way and 3-Way Zone Valves
AB
A
A
AB
B
Standard Features
Line Sizes:
1/2” - 1”
Body Style:
Globe

UL Listed for Plenum installations.

All metal plug and seat.

Direct coupled bonnet—install actuator without tools.

Standard 2.5 mm strike.

Change from normally open to normally closed by simply changing actuators.

Visual position indicator.

Manual Override: 2 Position with auto lock, 3 Pt. Flt. & 0-10Vdc using hex wrench.
Valve Body
Flow Characteristic:
Body:
Trim:
Stem:
O-Rings:
Packing:
Medium:
Medium Temp Range:
Max. Inlet Pressure:
Leakage Rate:
Close Off Ratings:
2 Position Actuators
Voltage:
Frequency:
Power Consumption:
Run Time:
Nominal Stroke:
Nominal Force
Operating Temp:
Noise:
Linear
Brass
Brass
SS ASTM A582 type 303
EPDM
EPDM O-rings
Water, Glycol Solns. to 50%
34oF to 230oF (1oC to 110oC)
125 psig
ANSI Class III
ANSI/FCI 70-2, 2-way & 3-way valves
1/2” - 3/4” (44 psi), 1” (22 psi)
24 Vac +/- 20%
24 Vac - 50/60 Hz
9.8 VA
10 seconds
1/10-in. (2.5 mm)
24 lb. (105 N)
41oF to 122oF (5oF to 50oC)
<35 db
Available CV’s
2-Way:
3-Way:
1/2” - 1.0, 2.5, 4.0
3/4” - 4.1
1” - 7.0
1/2” - 1.0, 2.5, 4.0
3/4” - 4.1
1” - 7.0
3 Pt. Floating/ 0-10Vdc ACTUATORS (Non-Fail Safe)
Voltage:
24 Vac +/- 20%
Frequency:
24 Vac - 50/60 Hz
Power Consumption:
3 Pt. Flt. - 0.8 VA
0-10Vdc - 2.5 VA
Run Time:
3 Pt. Flt. - 150 sec.,
0-10Vdc - 34 sec.
Nominal Stroke:
1/10-in. (2.5 mm)
Nominal Force:
24 lb. (105 N)
Operating Temp:
41oF to 122oF (5oF to 50oC)
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
ATC Ball Valves
41
2-Way and 3-Way Ball Valves
Standard Features
Line Sizes:
1-1/4” - 2”
Body Style:
Ball

1/4 turn rotary control valves designed to be coupled with an OpenAir actuator.

Universal mounting plate accommodates different actuator sizes.

Variety of ball sizes and flow coefficients.

Actuator and plate can be rotated to facilitate installation and wiring.

Standoffs and mounting plate provide thermal barrier between the actuator and valve.

Plastic mounting plate, extension and handle do not condensate.

Operating handle can be manually operate valve in event of power failure.
Valve Body
Flow Characteristic:
Body:
Ball:
Ball Seals:
Flow Optimizer:
Stem:
Stem Seals:
Angle of Rotation:
Medium:
Medium Temp Range:
Static Pressure/Temp:
Close Off Ratings:
Fail Safe Actuators
Voltage:
Frequency:
Power Consumption:
Run Time:
Spring Return:
Running Torque:
Enclosure:
Equal %
Brass
Chrome Plated Brass
Glass-filled PTFE with EPDM O-rings
Glass-filled PTFE
Brass, Double O-ring, Blow-out proof
Brass, Double O-ring, Blow-out proof
0 to 90 degrees
Water, Glycol Solns. to 50%
35oF to 250oF (2oC to 121oC)
360 psig/250oF (600 WOG)
200 psi for all 2-way, 200 psi for all 3-way
24 Vac +/- 20%
24 Vdc +/- 15%
50/60 Hz
5 VA running, 4 VA holding
90 seconds
15 sec. (typical)
62 lb.
NEMA 1
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
3 Pt. Floating/ 0-10Vdc ACTUATORS (Non-Fail Safe)
Voltage:
24 Vac +/- 20%, 15%
Frequency:
50/60 Hz
Power Consumption:
3.3 VA
Run Time:
1-1/4” 2-way & 3-way: 90 sec.
1-1/2” - 2” 2-way & 3-way: 125 sec.
Running Torque:
1-1/4” 2-way & 3-way: 44 lb.
1-1/2” - 2” 2-way & 3-way: 88 lb.
Enclosure:
NEMA 1
Bellimo ATC Zone Valves
42
ATC Specs. - Body:
Body:
Ball:
Stem:
Seats:
Characterized Disc:
Packing:
Body Pressure Rating:
Media Temp. Range:
Close Off Pressure:
Max.
P:
Forged brass, nickel plated
Stainless Steel
Stainless Steel
PTFE
Tefzel®
2 EPDM O-rings, lubricated
400 psi
0o F to 250o F
100 psi
50 psi for typical applications
ATC Specs. - Actuator
Power Supply
Power Consumption:
Control Type:
Fail Safe:
Run Time:
Position Indicator:
Manual Override:
Housing:
24 VAC +/- 20% 50/60 Hz
5 W (running), 2.5 W (holding
2 Position (on/off)
Spring Return (reversible CW/CCW mounting)
< 75 seconds (motor), 20 seconds @ -4o F to 122o F, <60 seconds @ -22o F
Visual indicator 0o F to 95o F (0o F is full spring return position)
5mm hex crank (3/16” Allen) supplied
Nema2, IP54, Enclosure Type 2
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Siemens PICV Actuator
43
Actuators for:
1/2” to 1-1/4” Valve Bodies:
Spring Return (Fail Safe): 24 volt 3 point floating or 24 volt 0-10Vdc
Non-Spring Return (Fail-In-Place): 24 volt 3 point floating or 24 volt 0-10Vdc
Features:
Application:
Visual position indicator, manual override, direct mounting.
Heating or cooling applications, water/glycol solutions up to 50% in
closed loops.
Power:
24 Vac
Operating Temperature: 41oF to 122oF
1-1/2” to 2” Valve Bodies:
Non-Spring Return (Fail-In-Place): 24 volt 3 point floating or 24 volt 0-10Vdc
Features:
Application:
Visual position indicator, manual override, direct mounting.
Heating or cooling applications, water/glycol solutions up to 50% in
closed loops.
Power:
24 Vac
Operating Temperature: 23oF to 122oF
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
Condensate Hose
44
Tube:
Fittings:
Clamps:
3/4” ID x 1/8” wall clear PVC
White Nylon 3/4” NPT
Stainless Steel Worm Gear
Tube:
Fittings:
Clamps:
3/4” ID x 1/8” wall clear PVC
White Nylon 3/4” NPT
Stainless Steel Worm Gear
Tube:
Fittings:
Clamps:
Pan:
Drain “T”:
Outlet:
3/4”ID x 1/8” wall clear PVC
White Nylon 3/4” NPT
Stainless Steel Worm Gear
3/4” PVC Socket
3/4” Hose
3/4” MNPT
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
45
ChamFlex® Brass Sweat-Hose Adapter
A Sweat x 37o Flare Brass Adapter available in 1/2”, 3/4”, 1” and 1 1/4” sizes.
Hose assemblies can be supplied with sweat adapter on one, or both ends.
Advantages:
- Fewer Components
- Washer-less Design—seating metal against metal.
- Reduces the amount of brazed/soldered joints.
- Fewer leak paths.
- Less labor required for installation.
- Great for applications with space constraints.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
ChamFlex® Fire Retardant Hose Assemblies Installation Instructions
46
A) All applications should be checked to ensure that the proper hose assembly lengths are being installed:

Hose assemblies should not be installed in a “stretched” (taut) fashion. Some expansion and contraction of the
hose assembly can occur due to temperature variation, system pressures, and system cycling (see Figure #1).

All hose assemblies should be routed properly to avoid contact with other surfaces that could possibly cause
“chafing” (abrasion of the wire braided reinforcement).

The use of elbows and adapters should be considered to relieve hose “strain” (see Figure #2). Do not use any
plastic fittings or adapters.
Hose assemblies should not be “bent” past the minimum bend radius requirements listed in the chart below.
Hose assemblies showing evidence of “kinking” (being bent beyond the recommended bend radius) should not
be installed (see Figure #3).

B) All hose assemblies should be installed in the following fashion so that no “twisting” occurs:

Solid male pipe thread (NPT) ends should be installed first unless they are being connected to a “swivel” female
(NPT). The entire hose assembly must rotate during the tightening of this connection in order to avoid hose tube
damage.

The flared adapter on the “union” (female swivel) end should be removed with the male pipe (NPT) end of the
adapter connected to the appropriate port first.
CAUTION: Thread sealant or thread tape should not be used on “flared” connections. Additional thread sealant or
thread tape should not be applied to male pipe thread (NPT) ends where factory installed thread sealant is already
present.

The last step is to reconnect the flared swivel female coupling to the flared end of the adapter in a manner that
ensures that the hose assembly is not twisted (see Figure #4).
Visit www.chamflex.com to view safety guidelines for selecting hose.
WARNING: “Flux and solder drips have been found to weaken the stainless steel braiding on Chamflex® Hose Assemblies
which could lead to deterioration of the inner tube component causing ‘ballooning’ and eventual failure. Chamflex® Hose
Assemblies must be shielded with appropriate fire resistance materials or if possible, removed from service if soldering,
welding, or brazing is to occur in areas above or adjacent to said assemblies. Chamberlin Rubber Company, Inc. will not be
responsible for failed hose assemblies and/or subsequent damage that occurred by failing to follow the provided Installation
Instructions (and warnings) as well as the Safety Guide.”
NOTE: Be sure that the exterior of the hose does not come into contact with substances not compatible with 302/304
stainless steel, including (but not limited to) any substances that contain chlorides. Chlorides have been found to cause stress
CAUTION: When brass sweat adapters are being used, make sure that the hose assembly is disconnected from the
adapter prior to “sweating” it on. Excessive direct heat can damage the tube of the hose. The hose assembly
should be reattached to the adapter after the “sweating” operation has been performed and adapter properly cooled.
WARNING: To insure proper installation this hose assembly must be installed according to instructions.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
All Metal Stainless Steel Braided Single Hose Assembly Installation Instructions
47
A) All applications should be checked to ensure that the proper hose assembly lengths are being installed:

Hose assemblies should not be installed in a “stretched” (taut) fashion. Some expansion and contraction of the
hose assembly can occur due to temperature variation, system pressures, and system cycling (see Figure #1).

All hose assemblies should be routed properly to avoid contact with other surfaces that could possibly cause
“chafing” (abrasion of the wire braided reinforcement).

The use of elbows and adapters should be considered to relieve hose “strain” (see Figure #2). Do not use any
plastic fittings or adapters.
Hose assemblies should not be “bent” past the minimum bend radius requirements listed in the chart below.
Hose assemblies showing evidence of “kinking” (being bent beyond the recommended bend radius) should not
be installed (see Figure #3).

Hose
Size
Working
Pressure
Minimum Burst
(@ 72o F)
Temperature
Range
Minimum
Bend Radius
1 1/2”
300 PSI
1200 PSI
-20o F– 800o F
11.75”
2”
300 PSI
1200 PSI
-20o F– 800o F
12.55”
2.5”
300 PSI
1200 PSI
-20o F– 800o F
16”
B) All hose assemblies should be installed in the following fashion so that no “twisting” occurs:

Solid male pipe thread (NPT) ends should be installed first unless they are being connected to a “swivel”
female (NPT). The entire hose assembly must rotate during the tightening of this connection in order to avoid
hose tube damage.

The male union end should be removed with the male pipe (NPT) end of the union connected to the
appropriate port first.
CAUTION: Thread sealant or thread tape should not be used on union connections. Additional thread sealant or
thread tape should not be applied to male pipe thread (NPT) ends where factory installed thread sealant is already
present.

The last step is to reconnect the male union coupling to the female swivel hose end in a manner that ensures
that the hose assembly is not twisted (see Figure #4).
Visit www.chamflex.com to view safety guidelines for selecting hose.
WARNING: “Flux and solder drips have been found to weaken the stainless steel braiding on Chamflex®
Hose Assemblies which could lead to deterioration of the inner tube component causing ‘ballooning’ and
eventual failure. Chamflex® Hose Assemblies must be shielded with appropriate fire resistance materials or if
possible, removed from service if soldering, welding, or brazing is to occur in areas above or adjacent to said
assemblies. Chamberlin Rubber Company, Inc. will not be responsible for failed hose assemblies and/or
subsequent damage that occurred by failing to follow the provided Installation Instructions (and warnings) as
well as the Safety Guide.”
NOTE: Be sure that the exterior of the hose does not come into contact with substances not compatible with
304L stainless steel, including (but not limited to) any substances that contain chlorides. Chlorides have been
found to cause stress corrosion cracking of the stainless steel braid and eventual failure.
WARNING: To insure proper installation this hose assembly must be installed according to instructions.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
48
VALVE INSTALLATION, OPERATION AND SERVICE INSTRUCTIONS
INSTALLER: PLEASE LEAVE THIS MANUAL FOR THE OWNER’S USE
GENERAL SAFETY NOTES:
WARNING: It is possible, depending on the age or condition of the product, for some liquid to escape when operating blow-down
ball valves. Safety goggles should be worn while servicing the product. In this case, arrangements should be made to replace
leaking valves. Failure to follow these instructions could result in serious personal injury.
WARNING: Check for proper sealing when using as an isolation valve. If the seat is not sealing properly, liquid will continue to
flow from the drain valves. In this case, arrangements should be made to replace leaking valves. Failure to follow these instructions could result in serious personal injury or death and property damage.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
49
HOW TO USE PRESSURE TAPS TO MEAUSRE SYSTEM OPERATING CONDITIONS
1.
Using Bell & Gossett’s Model RP-250B readout probes, attach a Bell & Gossett differential pressure readout kit to the readout valves on
the Accessory valve.
WARNING: Hot water leakage can occur from readout valve during probe insertion and during hookup of readout kit. Follow the instruction manuals supplied with the readout probes and readout kit for safe use. Failure to follow this instruction could result in serious personal
injury and/or property damage.
2.
Read the differential pressure across the coil. This can be compared to system pump head to determine system flow blockage.
3.
Differential pressure can also be taken at Circuit Setter, AFLV and Y-strainer.
GENERAL INFORMATION:
For Installing Sweat Connections:
1.
Clean tube ends and valve connections thoroughly per good piping practices with a fine grade emery cloth or fine grit sandpaper.
2.
For soldering, use 95-5 (Tin-Antimony) solder and a good grade of flux.
3.
Use a torch with a sharp point flame.
4.
When sweating the joints, first adjusting the valve in the full open position, then wrap the vale with a cool wet rag and then direct the
flame with care to avoid subjecting the valve to excessive heat. Allow the valve to cool before torching or operating.
5.
Check the soldering connection for leaks.
WARNING: Use of improper procedures to sweat valve model with union connection into system can damage valve. Before installing sweat union connection to valve, remove the union nut and O-ring from the valve body, then union tailpiece with nut must
be sweated (soldered) into place. Make sure the O-ring is reinstalled. Failure to follow this instruction could result in property
damage and/or moderate personal injury.
CAUTION: Heat associated with the use of silver solder may damage valve components and void the product warranty. Do Not
use silver solder. Failure to follow these instructions could result in property damage and/or moderate personal injury.
CAUTION: Excessive use of solder or flux may result in damage to the shutoff valve seat and ball. Do not use excessive solder or
flux. Failure to follow these instructions can result in moderate personal injury and/or property damage.
For Installing NPT Connections:
Apply pipe compound conservatively to male connecting fittings only. After installation check all joints for leakage and retighten where necessary.
CAUTION: The use of “Teflon®” impregnated pipe compound and “Teflon®” tape on pipe threads provides lubricity. Care
should be taken to prevent over-tightening which may damage the valve body. Failure to follow these instructions can result in
moderate personal injury and/or property damage.
CAUTION: Do not use pipe dope where thread sealant is pre-applied when connecting valves to ChamFlex/All Metal SS Braided
Hose Assemblies.
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
50
Model AC Circuit Sentry Automatic Flow Limiting Valve
Description: The Automatic Flow-Limiting Valves (AFLV) are designed to automatically control the flow in piping systems to selected
Preset limit. As pressure differential increases, a cartridge inside the valve body reduces the flow area to accurately maintain the
Preselected flow rate.
Installation Instructions:
1.
The valves must be installed on the return side of the coil with union ended on the upstream side and other end on the downstream side.
2.
Install the unit so that the flow arrow on the body housing points in the direction of flow.
Operating Instructions: Operation of the Automatic Flow-Limiting Valves is fully automatic and does not require any adjustment. It automatically
maintains the selected flow over the designed differential pressure range.
CAUTION: Hot uninsulated surfaces can cause burns to the skin. Do not touch hot surfaces. Failure to follow these instructions could
result in moderate personal injury.
Before the system start up, remove cartridge from the valve. Flush the hydronic system and then reassemble cartridge into the valve and make sure cap
is tightened properly. Start the system and check for the AFLV leak.
How to use Automatic Flow-Limiting Valve Pressure Taps to Determine Proper Function of Valve:
1.
Using Bell & Gosset Model RP-250B readout probes, attach a Bell & Gosset differential pressure readout kit to the readout valves on the Automatic Flow-Limiting Valve.
2.
Read the differential pressure across the Automatic Flow-Limiting Valve. This can be compared to system pump head to determine valve function
and system flow blockage.
CAUTION: Hot water leakage can occur from read-out valve during probe insertion and during hookup of readout kit. Follow the instruction manual supplied with readout probe and kit for safe use. Failure to follow this instruction could result in serious personal injury and/
or property damage.
Service Instructions: Should the Automatic Flow-Limiting Valve require cleaning or changing the orifice, follow the following instructions.
WARNING: System fluid under pressure and/or at high temperature can be very hazardous. Before servicing reduce system pressure to zero or isolate
the pressure reducing from the system. Leave drain valve open. Allow system to cool below 100 oF (38oC). Failure to follow these instructions could
result in serious personal injury or death and property damage.
1.
Loosen and remove the cap from the valve body.
2.
Pull the cartridge assembly from the valve body for cleaning or replacing with the new flow cartridge. Check the cartridge by pushing the orifice
washer into the cartridge housing for several times to make sure spring is functional.
3.
To change orifice washer (for a different flow valve). Remove the clip ring from inside the cartridge housing with a screwdriver. Pull the orifice
washer out and replace with the new orifice size as required.
4.
Reinstall retaining clip (or replace clip ring, if damaged) in the cartridge-housing groove. Slide cartridge into the body. Reassemble the cap with the
O-ring to body with appropriate torque.
WARNING: Corrosion or leakage is indication that the Automatic Flow-Limiting Valve must be replaced. Failure to follow these instructions could
result in serious personal injury or death and property damage.
WARNING: To ensure proper installation this product must be installed in conformance with
applicable building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
PH: (585) 427-7780 Fax: (585) 427-2429 PO Box 22700 ~ Rochester, NY 14692
www.chamflex.com
Revision Date: 10/2015
51
Model AM Flo-Setter Balance and Commissioning Valve
Description: Bell & Gossett Model AM Flo-Setter Balance & Commissioning Valves are precision engineered valves used in heating and cooling sys-
tems for the distribution of flow in various sections of the system. The dynamic balancing and commissioning valve ensures easy and reliable balancing
of the system, regardless of any fluctuations in the differential pressure of the system. The Bell & Gossett Circuit Sentry Flo-Setter limits the maximum
flow in the system and can be sued in both variable and constant flow systems. The clear scale on the lockable handle ensures that flow setting is simple
and user friendly while the integral P/T ports allow verification of pressure.
Installation Instructions:
Circuit Sentry Flo-Setter Balance & Commissioning valves are uni-directional valves and can be installed in most altitudes; however, they should be
installed in a position to facilitate the ease of balancing the system. Be sure to install the Circuit Sentry Flo-Setter with the arrow pointing in the direction
of flow.
Circuit Balance valves with NPT Connections:
Apply pipe compound conservatively to male connecting fittings only. Check connection for leaks.
CAUTION: The use of Teflon® impregnated pipe compound and Teflon® tape on threads provides lubricity. Care should be taken to prevent over
tightening of the valves which may damage the Circuit Sentry Flo-Setter.
CAUTION: Do not use pipe dope where thread sealant is pre-applied when connecting valves to ChamFlex/All Metal SS Braided Hose Assemblies.
Operation Instructions:
How to use Bell & Gossett Circuit Sentry Flo-Setter Balance & Commissioning Valves for Pre-Set Flow Balancing:
The Circuit Sentry Flo-Setter Balance & Commissioning Valve is easily set, and the pre-setting is read on the scale. The flow rate of the valve can be
determined from the flow rate graphs for the valve dimension in question. See the flow rate graphs of the valve in the FLOW CURVE BOOK
(G10092) or Submittal (A-609.22 or A-611) for further information about the adjustment setting. Select the appropriate size Circuit Sentry Flo-Setter
Balance & Commissioning Valve (normally line size) for the required GPM.
Please note: The scale is for the adjustment of flow. If you want to close the branch line, use an isolation ball valve in conjunction with the Circuit Sentry Flo-Setter.
The handle can be locked after adjustment. Remove the B&G logo cap and tighten with 5mm hexagonal key.
How to use Bell & Gossett Circuit Sentry Flo-Setter to Proportional Balance System:
The system is easily balanced by adjusting the pump according to the required differential pressure across the critical valve. When the differential pressure is available the system will automatically be balanced.
How to use Bell & Gossett Circuit Sentry Flo-Setter Balance & Commissioning valves as Flow Meters:
The flow through the valve can be identified by measuring the differential pressure
p across the valve. If the measured differential pressure is above
the minimum p, the flow is the one stated on the graph for the valve. If the measured differential pressure is below the minimum
p, the flow can
be found by using the formula below.
Q = Cv x
Service Instruction:
P
Q
Flow Rate
GPM
Cv
Flow Coefficient
GPM/PSI
P
Differential Pressure
PSI
Periodically inspect the Circuit Sentry Flo-Setter for signs of leakage or corrosion.
Insulation:
Bell & Gossett recommends that insulation be attached to the Circuit Sentry Flo-Setter after the system has been balanced.
Note: Tape or other acceptable means should be sued to secure the insulation to the Circuit Sentry Flo-Setter Balance & Commissioning Valve.
WARNING: To ensure proper installation this product must be installed in conformance with
applicable building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
PH: (585) 427-7780 Fax: (585) 427-2429 PO Box 22700 ~ Rochester, NY 14692
www.chamflex.com
Revision Date: 10/2015
52
Siemens PICV Automated Balance Valve
Description: Siemens Pressure Independent Control Valves integrate three functions into a single device: control valve, adjustable flow
limiter, and automatic pressure regulator. The 1/2” Normally Open valves have a 2.5 mm stroke, and a threated valve bonnet for use
with SSD Electronic Valve Actuators. The 3/4” Normally Open and 1/2” to 1-1/4” Normally Closed valves have a 5mm stroke, and a
threaded valve bonnet for use with SSD Electronic Valve Actuators. The 1-1/2” and 2” Normally Closed valves have a 6.5 mm stroke,
and a threaded valve bonnet for use with SQD Electronic Valve Actuators.
Feature:
* Control valve with integrated pressure regulator and adjustable flow limiter
* ANSI Class 250 valve body
* 200 psi close-off with ANSI Class IV leakage (1/2” and 3/4” Normally Open)
* 45 psi close-off with ANSI Class IV leakage (1/2” to 1-1/4” Normally Closed)
* 50 psi close-off with ANSI Class III leakage (1-1/2” to 2” Normally Closed)
* Linear Flow Characteristic
* Stainless Steel Stem
P/T Ports Installation:
For 1/2” and 3/4” Normally Open Valves: The low-pressure P/T port (blue indicator ring) should be located on the downstream side
of the valve. The high pressure P/T port (red indicator ring) will be located on the upstream or inlet side of the valve.
For 1-1/2” and 2” Normally Closed Valves: The low-pressure P/T port (blue indicator ring) should be located closest to the end connection. The high-pressure P/T port (red indicator ring) will be located closest to the valve system.
Presetting Adjustment: Prior to mounting the actuator, remove the black control knob cover from the valve to verify the valve is set to
ordered flow setting.
To change the valve flow setting see steps 2, 3 and 4 below. (Flow setting scales are in gallons per minute (gpm) on all valves);
NOTE: When tightening the knurled nut, some force is required to reach the required physical stop; approximately an additional 1/2 to
3/4 extra turn after initial “finger tight” resistance is felt.
WARNING: To ensure proper installation this product must be installed in conformance with
applicable building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
PH: (585) 427-7780 Fax: (585) 427-2429 PO Box 22700 ~ Rochester, NY 14692
www.chamflex.com
Revision Date: 10/2015
53
Siemens PICV (cont.)
Mounting and Installation: Install the valve so the flow follows the direction of the arrow indicated on the valve body. For best performance, install the valve assembly with the actuator above the valve body. The valve and actuator can be installed in any position between
vertical and horizontal. See Figure 1. Do not install the valve assembly with the actuator below horizontal or upside down.
NOTE: Allow sufficient space for servicing the valve and actuator.
Commissioning Notes:
CAUTION: The Pressure Independent Control Valves must be open when flushing or pressure testing the system. Strong pressure
impacts can damage closed Pressure Independent Control Valves.
CAUTION: Differential pressure across the valve greater than 58 psi will result in damage to the pressure regulator.
CAUTION: Hot uninsulated surfaces can cause burns to the skin. Do not touch hot surfaces. Failure to follow these instructions could result in
moderate personal injury.
WARNING: To ensure proper installation this product must be installed in conformance with
applicable building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
PH: (585) 427-7780 Fax: (585) 427-2429 PO Box 22700 ~ Rochester, NY 14692
www.chamflex.com
Revision Date: 10/2015
54
Model MC Circuit Setter
Description: Circuit Setter Balance Valves are precision engineered valves which function as precise system balancing valves and highly accurate variable orifice flow meter.
Installation Instructions:
1.
The valve should be installed on the return side of the coil with the union end on the upstream side and other end on the downstream side (except
on the bypass line).
How to use Bell & Gossett Circuit Setter Balance Valves for Pre-Set Flow Balancing: All Circuit Setter Balance Valves within a common zone,
circuit or system, with a common pump, are brought into balance with each other by establishing a common BALANCE GOVERNING HEAD LOSS
as noted.
CAUTION: Hot uninsulated surfaces can cause burns to the skin. Do not touch hot surfaces. Failure to follow these instructions could result in
moderate personal injury.
1.
Identify a zone within a given circuit or circuit within a given system with the highest head loss.
2.
Establish the value of the head loss in feet of water.
3.
Establish the corresponding required GPM.
4.
Select the appropriate size Circuit Setter Balance Valve (normally line size) for the required GPM.
5.
Using Side #1 of the V91483 Circuit Setter Balance Valve Calculator, set the degree of closure hairline in the red section of the Calculator of the 0o
setting for the appropriate size Circuit Setter and read the head loss opposite the require CPM. The setting for this Circuit Setter will remain 0o.
6.
7.
Add the head loss in Step “5” to the head loss in Step “2” to establish the Balancing Governing Head Loss for the zone or circuit.
Subtract the required head loss for each zone circuit from the Balance Governing Head Loss in Step “6” to establish the head loss difference for
each zone or circuit which is to be brought into balance with Step “6”.
8.
The head loss difference in Step “7” and the required GPM in Step “3” are lined up in the white section of Side #1 of the
Calculator and the
degree of closure for the specific Circuit Setter Balance Valve is shown under the degree of closure hairline in the red section of the Calculator for
the appropriate size Circuit Setter.
9.
Adjust the Circuit Setter by turning the red knob by hand on sizes 1/2” through 1”, or by placing a wrench on the wrench flats provided on sizes 1
1/4” through 2 1/2” to the set position determined by the preceding procedure.
WARNING: It is possible, depending on the age or condition of the stem seal, for some liquid to escape during Circuit Setter adjustment. Do not have
eyes or face on a level with the sides of the Circuit Setter. Failure to follow this warning could result in serious personal injury.
NOTES:

Head loss in Steps “6” and “2” are a fixed head requirement the zone, circuit or system pump, as required, must overcome.

Refer to the G95872 prewired tag packaged with the Circuit Setter Balance Valve and fill in the appropriate information. Attach the tag to the Circuit Setter for future reference.
How to use Bell & Gossett Circuit Setters to Proportional Balance a System:
1.
2.
Open fully all Circuit Setters on a single pump system.
If more than one branch circuit is used, start the balance procedure by reading all of the flows to the units in a branch. Each unit (coil) should have
its own Circuit Setter for flow balancing. Using Bell & Gossett RP-250B readout probes, sequentially attach a Bell & Gossett differential pressure
readout kit to the readout valves on each Circuit Setter Balance Valve.
WARNING: Hot water leakage can occur from readout valve during probe insertion and during hookup of readout kit. Follow the instruction manual supplied with the readout probes and readout kit for safe use. Failure to follow this instruction could result in
serious personal injury and/or property damage.
3.
Using Side-2 of the Bell & Gossett Circuit Setter Balance Valve Calculator, with the top hairline set on zero for the size Circuit Setter being read,
read the flow corresponding to the pressure drop read with the read out kit.
4.
Calculate the ratio of the actual flow to the design flow for each unit in the branch. This is the proportional flow rate. (Actual flow divide by design flow.)
Select the Circuit Setter with the lowest proportional flow rater. This Circuit Setter is left in the full open position. Every other Circuit Setter in the
branch is then reset to the same proportional flow rate.
5.
WARNING: To ensure proper installation this product must be installed in conformance with
applicable building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
PH: (585) 427-7780 Fax: (585) 427-2429 PO Box 22700 ~ Rochester, NY 14692
www.chamflex.com
Revision Date: 10/2015
55
Manual Circuit Setter Cont.
6.
If there are additional branches, repeat the steps in 3, 4 and 5 above for each branch.
7.
After all branches have been proportionally balanced, measure the full open flows on the Circuit Setters installed on the risers. Calculate the
proportional ration of each riser Circuit Setter and select the one with the lowest proportional ratio. This Circuit Setter is left fully open and the
other riser Circuit Setters are adjusted to this same ratio as described in (5).
8.
Adjust pump flow so that circuits are receiving their design flow. This can be accomplished by adjusting a Circuit Setter Balance Valve installed on
the pump discharge or by changing the pump impeller size.
IMPORTANT: Of a high degree of throttling of flow at pump discharge is required Bell & Gossett recommends that the pump impeller be sized to
produce design flow. This will reduce electrical energy consumption.
How to use Bell & Gossett Circuit Setter Balance Valves as Flow Meters:
1.
2.
Energize the zone, circuit and/or system pump(s) as applicable.
Using Bell & Gossett Model PR-250B Readout Probes, sequentially attach a Bell &Gossett differential pressure readout kit to the read out valves on
each Circuit Setter Balance Valves.
WARNING: Hot water leakage can occur from readout valve during probe insertion and during hookup of readout kit. Follow the instruction manual a
supplied with readout probes and readout kit for safe use. Failure to follow this instruction could result in serious personal injury and/or property
damage.
3.
Read the differential pressure across the orifice of the Circuit Setter Balance Valve.
4.
Using Side #2 of the Circuit Setter Balance Valve Calculator, set the hairline over the degree of closure as indicated by the part of the red plastic
knob or indicator plate parallel to the degree of closure noted on the calibration plate, and read actual GPM flowing through the Circuit Setter opposite the gauge reading head loss noted in the white section of Side #2.
NOTE: If the system contains a liquid with a specific gravity and/or viscosity higher or lower than that of water, apply the appropriate correction factor
noted in these instructions to obtain the actual GPM for the system liquid.
How to Bell & Gossett Circuit Setter Balance Valves as an Isolation Valve:
1.
Move the adjustment knob or stem until the position indicator aligns with the closed position on the calibration plate.
2.
Close the isolation valve on the other side of the equipment to be serviced.
3.
Open the drain valve to drain the system between the Circuit Setter and the second isolation valve.
WARNING: Check for proper sealing when using as an isolation valve. If the sea is not sealing properly, liquid will continue to flow from the drain
valves. In this case, Circuit Setter must be isolated from the system and replaced. Failure to follow these instructions could result in serious personal
injury or death and proper damage.
How to use the Memory Stop feature:
1.
Make the final degree of closure setting.
2.
Loosen the memory stop locking screw in the slot on the top of the red knob.
3.
Slide the memory stop screw in the slot (counter-clockwise for 1/2” - 1” sizes and clockwise for 1 1/4” - 2 1/2” sizes) until the screw stops.
4.
Tighten the memory stop screw.
Servicing Instructions:
Periodically inspect the Circuit Setter for signs of leakage or corrosion.
WARNING: Corrosion of leakage is indication that the Circuit Setter must be replaced. Failure to follow these instructions could result in serious personal injury or death and property damage.
WARNING: To ensure proper installation this product must be installed in conformance with
applicable building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
PH: (585) 427-7780 Fax: (585) 427-2429 PO Box 22700 ~ Rochester, NY 14692
www.chamflex.com
Revision Date: 10/2015
56
Ball Valve
Installation Instructions:
1.
Ensure the pipeline is free of dirt of debris. Flush system if necessary. Foreign matter can damage valve or degrade performance.
2.
Thoroughly clean pipe threads and apply thread dope to the male thread only. PTFE thread sealant is recommended for most
applications. (Installer is responsible for selecting a sealant compatible with fluid).
CAUTION: The use of “Teflon” impregnated pipe compound and “Teflon” tape on pipe threads provides lubricity. Care should
be taken to prevent over-tightening which may damage the valve body. Failure to follow these instructions can result in moderate
personal injury and/or property damage.
Do not use pipe dope where thread sealant is pre-applied when connecting valves to ChamFlex/All Metal SS Braided Hose Assemblies.
3.
Apply torque to the valve at wrenching flats nearest the end being assembled. Do not apply torque through the full length of the
valve body as this may compromise the integrity of the body to end piece seal. Care should taken not to over tighten as this as this
can cause distortion of the valve body and effect valve performance. Pipe wrenches should not be used on the valve as they can
crush the body distorting the NPT thread.
4.
A tight leak free joint can be obtained on valves 2” and under by rotating the valve 2 to 3 turns relative to the pipe, larger valves
should be turned 1 1/2 to 2 turns. (Basic Dimensions, American National Standards Taper Pipe Threads, NPT ANSI B1.20.1-1983.)
5.
After installation operate the valve through several full open to close cycles. Check tightness of stem packing.
6.
For valves with NPT side taps assembly is the same as end connections. Tighten the mating part 2 to 3 turns past hand tight while
holding the valve securely. The valve should be secured at the wrenching flats only. Applying a radical load on the main part of the
body can distort it.
Operation Instructions:
The valve is opened by turning counterclockwise one quarter turn and close by turning clockwise. Valve state is indicated by the lever. A
closed valve’s lever is at 90o to the valve axis. When the valve is open the lever lies along axis.
CAUTION: Hot uninsulated surfaces can cause burns to the skin. Do not touch hot surfaces. Failure to follow these instructions could result in
moderate personal injury.
WARNING: To ensure proper installation this product must be installed in conformance with
applicable building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
PH: (585) 427-7780 Fax: (585) 427-2429 PO Box 22700 ~ Rochester, NY 14692
www.chamflex.com
Revision Date: 10/2015
57
Model MV Venturi/Ball Valve Combination
Description: The Bell & Gossett Model MV is a combination calibrated balance, commissioning and positive shutoff valve for use in HVAC systems.
An efficient brass venturi design provides accurate flow balancing with minimal system pressure loss. Valves are furnished with two readout valves
(pressure and temperature ports), standard port ball valve with memory stop, and hanging ID tag for commissioning. A variety of end connections are
available on both the fixed and union ends. Venturi/Ball valve provides highly accurate flow measurement capabilities.
WARNING: Damage to the Venturi/Ball valve or failure of solder sealing joints may occur if these operational limits are exceeded. This can result in
water leakage. Failure to follow this instruction can cause serious personal injury and/or property damage.
Installation Instructions:
For Installing Sweat Connections:
1.
Clean tube ends and valve connections thoroughly per good piping practices with a fine grade emery cloth or fine grit sandpaper.
2.
For soldering, use 95-5 (Tin-Antimony) solder and a good grade of flux.
3.
Use a torch with a sharp pointed flame.
4.
When sweating the joints, first adjusting the valve in the full open position, then wrap the valve with a cool wet rag and then direct the flame with
care to avoid subjecting the valve to excessive heat. Allow the valve to cool before touching or operating.
5.
Check the soldered connection for leaks.
WARNING: Use of improper procedures to sweat valve model with union connection into system can damage valve. Before installing sweat union
connection to valve, remove the union nut and O-ring from the valve body, then union tailpiece with union nut must be sweated (soldered) into place.
Failure to follow this instruction could result in property damage and/or moderate personal injury.
CAUTION: Heat Associated with the use of silver solder may damage a Venturi/Ball valve and void the product warranty. Do not use silver solder.
Failure to follow these instructions could result in property damage and/or moderate personal injury.
For installing NPT Connections:
Apply pipe compound conservatively to male connecting fittings only.
CAUTION: The use of Teflon® impregnated pipe compound and Teflon® tape on pipe threads provides lubricity. Care should be taken to prevent
overtightening which may cause damage to the valve body. Failure to follow these instructions can result in moderate personal injury and/or property
damage.
CAUTION: Do not use pipe dope where thread sealant is pre-applied when connecting valves to ChamFlex/All Metal SS Braided Hose Assemblies.
After installation check all joints for leakage and retighten where necessary.
Operation Instructions
1.
2.
Energize the zone, circuit and/or system pump(s) as applicable.
Using Bell & Gossett Model RP-250B Readout Probes, sequentially attach a Bell & Gossett differential pressure readout kit to the readout valves on
each Venturi/Ball valve.
3.
Read the differential pressure across the orifice of the Venturi/Ball valve
4.
Using the differential pressure data sheet #EP-600 of the Venturi/Ball to read the actual GPM.
Example: The Venturi/Ball valve model 3/4” L. If the differential pressure across the orifice read at 46” W.C. the flow rate is 4 GPM.
WARNING: Hot water leakage can occur from readout valves during probe insertion and during hookup of readout kit. Follow the instruction manual
supplied with readout probes and read out kits for safe use. Failure to follow these instructions could result in serious personal injury or death and
property damage.
How To Use The Memory Stop Feature:
1.
Make the final degree of closure setting.
2.
Loosen the handle nut and rotate memory stop until against the body locking.
3.
Tighten the handle nut.
Service Instructions:
Periodically inspect the Venturi/Ball valve for signs of leakage or corrosion.
WARNING: Corrosion or leakage is indication, that the Venturi/Ball must be replaced. Failure to follow these instructions could result in serious
personal injury or death and property damage.
CAUTION: Hot uninsulated surfaces can cause burns to the skin. Do not touch hot surfaces. Failure to follow these instructions could result in
moderate personal injury.
WARNING: To ensure proper installation this product must be installed in conformance with
applicable building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
PH: (585) 427-7780 Fax: (585) 427-2429 PO Box 22700 ~ Rochester, NY 14692
www.chamflex.com
Revision Date: 10/2015
58
Y-Strainer Combination Valve
Description: Y-strainer valves are of brass construction with an integrated ball valve, strainer, blow-down valve and union with tailpiece.
Installation Instructions:
1.
The valves must be installed on the supply side of the coil with filed end on the upstream side and other end on the downstream side.
2.
When installing the Y-strainer valves space around the units must be provided to move the valve handle to the shutoff position and to move the
strainer from the strainer body for cleaning.
3.
The Y-strainer must be installed with the strainer chamber down to prevent air binding and also to allow accumulated dirt to be blown down from
the strainer.
Operation Instructions:
Y-strainer can be used to isolate hydronic equipment for repairs and/or drain the system. To close the Y-strainer ball valve move the handle a quarter of
a turn until the handle is perpendicular to the valve and piping.
If Y-strainer pressure drop becomes excessive, accumulated dirt should be blown down through the blow-down line (if installed) to a drain. If a blowdown line is not installed see the service instructions for removing and cleaning the strainer. The Y-strainer have construction with an integrated ball
valve will function as a service valve.
Service Instructions:
If excessive pressure drop is measured across the Y-strainer the internal strainer has collected dirt/debris and needs to be cleaned. Install blow-down
line (hose), then open blow-down valve. If blowing down the strainer has not solved the pressure drop problem, the Y-strainer must be disassembled
and strainer cleaned.
WARNING: Failure to use proper hose connection to the blow-down valve may result in serious personal injury and property damage.
To clean the strainer, isolated the Y-strainer by shutting off the ball valve on upstream and downstream of the Y-strainer. Allow the system to cool
down to 100oF (38oC) or less.
WARNING: Hot fluid and/or fluids under pressure are a safety hazard. Do not service the strainer while it is hot or under pressure. Failure to follow
these instructions could result in serious personal injury or death and property damage.
Using the appropriate size wrench remove the brass cap on the Y portion of the strainer. Grab and remove the strainer. Clean the strainer in water to
remove collected debris. Reinstall the strainer and the strainer cap. Pressurize the system and check for strainer cap leaks. If noted, slightly tighten nut
until leakage stops.
Periodically inspect the Y-strainer for signs of corrosion or leakage. If corrosion or leakage is noted the Y-strainer must be replaced.
WARNING: Corrosion or leakage is indication that the Y-strainer Combination Valve must be replaced. Failure to follow these instructions could
result in serious personal injury or death and property damage.
CAUTION: Hot uninsulated surfaces can cause burns to the skin. Do not touch hot surfaces. Failure to follow these instructions could result in
moderate personal injury.
WARNING: To ensure proper installation this product must be installed in conformance with
applicable building codes. Use of proper torque wrench is required.
Chamberlin Rubber Company, Inc.
PH: (585) 427-7780 Fax: (585) 427-2429 PO Box 22700 ~ Rochester, NY 14692
www.chamflex.com
Revision Date: 10/2015
59
Abbreviations Index
Acronym
Definition
P
AFLV
ANSI
ASTM
ATC
BDV
Cv
EPTF
FNPT
FSWT
GPM
HNBR
JIC
KPA
MAV
MFR
MNPT
NC
NO
PICV
PSI
PSID
PT
PTFE
UBY
Differential Pressure
Automatic Flow Limiting Valve
American National Standards Institute
American Society for Testing Materials
Automatic Temperature Control
Blow Down Valve
Flow Co-efficient
Ethylene Propylene Thermoplastic Rubber
Female National Pipe Thread
Female Sweat
Gallons Per Minute
Hydrogenated Nitrile
Joint Industrial Committee
Kilo Pascal
Manual Air Vent
Maximum Flow Recommendation
Male National Pipe Thread
Normally Closed
Normally Open
Pressure Independent Control Valve
Pounds per Square Inch
Pounds per Square Inch Gauge
Pressure Taps
Polytetraflouroethylene
Union Ball Valve with “Y” Strainer
Chamberlin Rubber Company, Inc.
www.chamflex.com
Revision Date: 10/2015
60
FLAME, SMOKE & TOXICITY Tested
Rubber Materials for passenger railcar applications.
Tested to the most stringent industry standards.
ASTM E 162
BS 6853
ASTM E 662
BSS 7239
ASTM E 1354
NF F 16-101
ASTM D 3675
SMP 800 C
ASTM C 542
(ASTM C 1166 procedure)
Chamberlin Rubber Company, Inc. is a supplier of
custom die-cut gaskets, pads, strips, and subassemblies as well as extruded molded parts.
ChamFlex® Hose Assemblies & Kits
Stainless steel braided heat pump hose assemblies
and kits. Our tube component is tested to and
awarded a UL-94 VO fire rating.
Flexible
UL-94 VO Rated Tube Component
Abrasion Resistant
Washer-less Design
Custom Manufactured
ChamFlex® Single Hose Assemblies:
ChamFlex® hose: Fixed End x Swivel End w/ JIC Adapter
We supply window extrusions,
door seals, rubber cleats,
bellows, strips, bumpers, roof
panel seals, HVAC seals, battery door gaskets, and various
other materials for ceiling &
wall insulation, flooring, subflooring and anti-vibration/
anti-squeak.
ChamFlex® hose: Swivel End x Swivel End w/ JIC Adapters
ChamFlex® Hose Kits:
Model AA Ultra Setter Automatic Balance Hose Kits
Model AC Circuit Sentry Automatic Balance Hose Kits
Call Eric Schneider at (585) 758-1019 for information.
Ball Valve Manual Balance Hose Kits
Gaskets:
Chamberlin converts the most reliable materials available
to create finished products that withstand specified temperature, load and pressure conditions required by your
application.
Die Cutting Laminating Slitting Kiss-Cutting
Hand Fabrication Assembly & Kitting
Model MV (Venturi) Manual Balance Hose Kits
Siemens PICV Automatic Balance Hose Kits
Supply Valve Options:
(or)
ChamFlex® assemblies are custom-made in our warehouse to
meet customer specifications. Minimum length for 1/2” and
Gasket Materials:
Neoprene
Pressure Sensitive Adhesives
Silicone
Non-Asbestos Materials
Viton
Tubing
EPDM
Extrusions
Nitrile
Red Sheet
Tapes
Pure Gum
Pressure Sensitive Tapes
Polyurethane
Teflon®
EMI/RFI Shielding
Kapton®
Coated Fabrics
Weather-stripping
Cellular Products
Foam - Open & Closed Cell
Sponge - Open & Closed Cell
Call our Sales Department (585) 758-1027 or visit our website
www.chamberlinrubber.com
www.chamberlinrubber.com
Model AM Flo-Setter Automatic Balance Hose Kits
3/4” hose is 6” with 1” increments. Minimum length for 1”
and 1-1/4” hose is 9” with 1” increments.
Call Scott Harding at (585) 758-1018 or
Tim La Bar at (585) 758-1021 for more information
Ducting
Garage Exhaust
General Purpose
High Temperature
Material Handling
Retractable
Special Purpose & Utility Hose
FST Ducting
Insulation Material
High-Temperature Silica or Fiberglass
Fabrics
Tapes
Fibers
Ropes
Chamberlin Rubber Company, Inc.
Revision Date: 10/2015
PO Box 22700 - Rochester, NY 14692
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement