Sony SRS-X99 Quick start guide

Sony SRS-X99 Quick start guide
4-567-505-13(1)
This document introduces how to play music after connecting this unit to your Wi-Fi network.
Documents provided
A Wi-Fi network enables you to easily enjoy music stored in wireless devices in your home, such as a PC or smartphone/iPhone. For other connection or listening methods, refer to Help Guide (indicated on the right).
Wi-Fi Startup Guide (this document)
Personal Audio System
Wi-Fi Startup Guide
onnect the unit to an AC outlet and set the
First C
antenna in the upright position.
Listening to Music over Your Wi-Fi Network
Pull out
90 degrees
Xperia
Use an Android smartphone in which SongPal (free app) is
installed to configure the Wi-Fi settings of the unit.
PC (Media Go)
iPhone
Use an iPhone/iPad/iPod touch in which SongPal (free app)
is installed to configure the Wi-Fi settings of the unit.
PC (iTunes)
WPS
Use a wireless router with a WPS (AOSS) button to configure
the Wi-Fi settings of the unit with a push of the button.
Explains important safety information, BLUETOOTH connection method,
troubleshooting, etc.
PC (Windows Media Player)
Configure the Wi-Fi settings using a browser of a PC. Refer to the
Operating Instructions of the separate document, “Listening to music
via a Wi-Fi network”.
Help Guide (web document for a PC/smartphone)
Explains details about the unit; network and BLUETOOTH connection
method with various devices, High-Resolution Audio playback method,
etc.
Listen to music in your smartphone/iPhone/iPad/iPod
touch by operating SongPal.
Xperia (Music app)
Make sure that a LAN cable is not connected. A wired
and wireless connection cannot be used at the same
time.
SRS-X99
Operating Instructions (separate document)
Set the music stored in a PC to share and listen to it by
using Media Go.
Smartphone (SongPal app)
PC
Explains how to listen to music stored in your PC or other device over your
Wi-Fi network.
Choose your device or software to play music, then go to “ Listening
to music with the unit” overleaf.
Choose a Wi-Fi connection method depending on your device,
then go to “ Connecting the unit to your Wi-Fi network” below.
iPhone/iPad/iPod touch
http://rd1.sony.net/help/speaker/srs-x99/h_zz/
 Connecting the unit to your Wi-Fi network
Xperia
Use an Android smartphone such as an Xperia
in which SongPal (free app) is installed to
configure Wi-Fi settings of the unit.
This method requires a Wi-Fi connection of
the smartphone and a BLUETOOTH
connection between the smartphone and the
unit. The Wi-Fi setting information is sent
from the smartphone to the unit via
BLUETOOTH.
• Some wireless routers have multiple SSIDs.
Connect the unit and your Android
smartphone to the same SSID.
Required items: Xperia™ or other Android smartphone, wireless router
1
Preliminary steps:
 Connect your smartphone to your Wi-Fi network.
2
Tap the / (on/standby) button to turn
on the unit.
3
Make a BLUETOOTH connection between
the unit and smartphone.
If your smartphone does not support the NFC function,
see  to  on the right.
 Record the SSID and password of your router
that your smartphone is connecting to in the
following spaces.
 Tap and start up [SongPal] on your
smartphone.
For details, refer to the operating instructions of your
router.
Flashing
Slow flashing
SSID:
Follow the on-screen instructions.
The / (on/standby) indicator lights up in green.
Go to the next step when the LINK indicator begins to
flash slowly (once per 3 seconds). In some cases, this
slow flashing may take about 4 or 5 minutes to begin.
Check that the
is lit.
 Tap [SRS-X99] on your
smartphone.
PAIRING button
(BLUETOOTH) indicator
5
Configure Wi-Fi settings following the
SongPal instructions.
Flashing
*1 The first time you tap the (BLUETOOTH) PAIRING
button after purchasing this unit, the (BLUETOOTH)
indicator flashes quickly. To pair with another device,
tap and hold the (BLUETOOTH) PAIRING button
until it beeps.
Check that the LINK indicator lights up in
orange.
Lit
Flashing
Lit
The screen on the right is
displayed.
Touch and hold
until the
smartphone
responds.
When the indicator stays lit, the Wi-Fi connection is
established. Depending on the environment, it may take
more than 1 minute.
When a BLUETOOTH connection is established, the
(BLUETOOTH) indicator stops flashing and stays lit.
Pairing is completed in about 1 minute.
6
If password entry is required on
the display, select the SSID and
enter the password recorded in
step 1 - .
 Tap and start up
SongPal, then [Open
the Bluetooth setting
screen].
 Tap the (BLUETOOTH)
of the unit once.
 Install SongPal on your smartphone.
Search for SongPal on Google
Play™
 Set the BLUETOOTH function of the
smartphone to on.
 Touch the N-Mark on the unit with the
smartphone.
Password:
4
Non-NFC compatible smartphone
When the Wi-Fi connection fails, the LINK indicator flashes in
red. In this case, repeat the procedure from step 2.
The (BLUETOOTH) indicator begins to flash
quickly.*1
See overleaf to play back
iPhone
Use an iPhone in which SongPal (free app) is
installed to configure Wi-Fi settings of the
unit.
This method requires a Wi-Fi connection of
the iPhone and a BLUETOOTH connection
between the iPhone and the unit. The Wi-Fi
setting information is sent from the iPhone to
the unit via BLUETOOTH.
Required items: iPhone/iPad/iPod touch, wireless router
1
Preliminary steps:
 Confirm that your iPhone is
connected to your Wi-Fi
network.
2
Tap the / (on/standby) button to turn
on the unit.
3
4
Make a BLUETOOTH connection between the unit and iPhone.
 Tap the (BLUETOOTH)
unit once.
PAIRING button of the
 Search for the unit on the iPhone.
Check that the
is lit.
5
(BLUETOOTH) indicator
 Tap and start up [SongPal] on your
iPhone.
Follow the on-screen instructions.
• Some wireless routers have multiple SSIDs.
Connect the unit and your iPhone to the same
SSID.
Flashing
Tap [Settings]  [Bluetooth].
Slow flashing
Flashing
6
Configure Wi-Fi settings following the SongPal instructions.
 If [Share Wi-Fi settings?] is displayed, tap [Allow].
The screen on the right is
displayed.
 When the screen on the right
is displayed, tap [OK].
Lit
Check that the LINK indicator lights up
in orange.
Flashing
Lit
Turn on BLUETOOTH.
 Install SongPal on your iPhone.
The (BLUETOOTH) indicator begins to flash
quickly.*2
Search for SongPal on the
App Store
The / (on/standby) indicator lights up in green.
Go to the next step when the LINK indicator begins to
flash slowly (once per 3 seconds). In some cases, this
slow flashing may take about 4 or 5 minutes to begin.
*2 The first time you tap the (BLUETOOTH) PAIRING
button after purchasing this unit, the (BLUETOOTH)
indicator flashes quickly. To pair with another device, tap
and hold the (BLUETOOTH) PAIRING button until it
beeps.
When the indicator stays lit, the Wi-Fi connection is
established. Depending on the environment, it may
take more than 1 minute.
When a BLUETOOTH connection is established, the
(BLUETOOTH) indicator stops flashing and stays lit.
Tap [SRS-X99].
When the Wi-Fi connection fails, the LINK indicator flashes
in red. In this case, repeat the procedure from step 2.
See overleaf to play back
WPS
Configure Wi-Fi settings of the unit with a
push of each WPS (AOSS) button on the
wireless router and the unit.
• To check if your wireless router is compatible
with WPS (Wi-Fi Protected Setup™), refer to
the operating instructions of your router.
Required item: Wireless router with WPS (AOSS) button
1
Place the unit close to your wireless
router.
2
Tap the / (on/standby) button to turn
on the unit.
Flashing
3
Press and hold the WPS button of the
unit until it beeps (about 2 seconds).
4
Within 90 seconds, press the WPS
button*3 of the router.
Slow flashing
5
Check that the LINK indicator lights up in
orange.
Flashing
If the Wi-Fi connection fails
You can use a PC browser to configure Wi-Fi settings of the unit. Connect the unit to your PC using a
commercially-available network (LAN) cable.
Lit
For details, refer to the Operating Instructions, “Listening to music via a Wi-Fi network”.
The WPS button is on the rear of the unit.
The / (on/standby) indicator lights up in green.
Go to the next step when the LINK indicator begins to
flash slowly (once per 3 seconds). In some cases, this
slow flashing may take about 4 or 5 minutes to begin.
Depending on the wireless router, press and hold the
WPS button for a few seconds. For details, refer to the
operating instructions of your router.
*3 The WPS button may be called “AOSS button” depending
on the wireless router.
When the indicator stays lit, the Wi-Fi connection is
established. Depending on the environment, it may take
more than 1 minute.
When the Wi-Fi connection fails, the LINK indicator flashes in
red. In this case, repeat the procedure from step 2.
See overleaf to play back
Continued: “  Listening to music with the unit” overleaf
 Listening to music with the unit
Communication fees may be charged for downloading the app or browsing the Help Guide. The design and displays of the app may change without notice.
©2015 Sony Corporation Printed in China
Music stored in your PC
PC (Media Go)
Music stored in your smartphone/iPhone
Smartphone (SongPal app)
Required item: Media Go installed PC
You can listen to music stored in your PC with
the unit by using the software Media Go.
• Go to the following URL beforehand, and install or
update to the latest version of Media Go (free
software) on your PC.
For customers in Europe:
http://www.sony.eu/support
For customers in the U.S.A.:
http://esupport.sony.com/US
For customers in Canada:
http://esupport.sony.com/CA/
For customers in other countries/regions:
http://www.sony-asia.com/section/support
1
2
Connect the unit and PC to your Wi-Fi
network.
Tap the NETWORK button of the unit.
3
Required item: SongPal installed smartphone/iPhone/iPad/iPod touch
1
You can listen to music stored in your
smartphone/iPhone with SongPal (free app).
• For more details about SongPal, refer to the
Operating Instructions, “About SongPal”.
Prepare Media Go.
 Start up [Media Go] on your PC.
Connect the unit and smartphone/iPhone to
your Wi-Fi network.
 Select [Preferences...] from the [Tools] menu.
2
3
Set the unit on SongPal.
Play music in your smartphone/iPhone by
operating SongPal.
 Install SongPal on your smartphone/iPhone.
If SongPal is already installed, skip this procedure and go
to .
 Tap your smartphone/iPhone.
Search for SongPal on Google Play or the
App Store.
 Tap and start up [SongPal].
Follow the on-screen instructions.
 When the screen on the right is
displayed, tap [SRS-X99].
Preferences
The NETWORK indicator lights up in white, and the unit
switches to NETWORK mode.
Connect the unit and PC to the same SSID of your router.
See overleaf for connecting the unit to your Wi-Fi network,
and make sure the LINK indicator of the unit lights up in
orange.
 Select a song to play and adjust the volume.
Connect the unit and smartphone/iPhone to the same SSID
of your router.
See overleaf for connecting the unit to your Wi-Fi network,
and make sure the LINK indicator of the unit lights up in
orange.
Music is played back.
4
Set Media Go on your PC as the server.
 Select [Media Sharing], then check [Library name].
[Library name] can be changed to an arbitrary name.
5
Xperia (Music app)
Play music by operating Media Go on your PC.
Select (Throw) from the bottom of the Media Go
window.
 Select [SRS-X99] on the Throw menu of Media Go.
 Select a song to play and adjust the volume.
Required item: Music app-compatible Xperia
You can listen to music stored on your Xperia
by operating the Music app.
• This function is available when you have an
Xperia with the Music (or WALKMAN®) app
pre-installed.
• Update the Android OS of your Xperia to the
latest version beforehand.
• Your Xperia may need to disable [Auto-select
wireless option] of [Throw settings]. For details,
refer to the User guide of Xperia.
Media Sharing
Library name
1
Connect the unit and Xperia to your Wi-Fi
network.
Make sure that a check mark is in all three items of
[Media Sharing].
2
Play music in your Xperia by operating the Music app.
 Play music and adjust the volume.
 Tap and start up
([Music]) on your
Xperia.
Tap , then tap
[SRS-X99].
 After confirming the screen, select [OK].
Connect the unit and Xperia to the same SSID of your router.
See overleaf for connecting the unit to your Wi-Fi network,
and make sure the LINK indicator of the unit lights up in
orange.
Music is played back.
Music is played back.
PC (iTunes)
You can listen to iTunes music on your PC with
the unit using AirPlay.
• Update iTunes to the latest version beforehand.
Required item: iTunes installed PC
1
Connect the unit and PC to your Wi-Fi
network.
iPhone/iPad/iPod touch
2
You can listen to music stored in your iPhone/
iPad/iPod touch using AirPlay.
Play music by operating iTunes on your PC.
 Start iTunes on your PC.
Select
Required item: iPhone/iPad/iPod touch
 Select [SRS-X99] on the AirPlay menu of iTunes.
(AirPlay) on the iTunes window.
• Update the iPhone/iPad/iPod touch to the latest
version beforehand.
• The screen illustrations are examples using iOS 8.
1
Connect the unit and iPhone/iPad/iPod
touch to your Wi-Fi network.
2
Play music by operating iPhone/iPad/iPod touch.
 Swipe up the screen to
display the Control Center.
 Tap [SRS-X99].
 Select a song to play and adjust the volume.
Tap
Connect the unit and PC to the same SSID of your router.
See overleaf for connecting the unit to your Wi-Fi network,
and make sure the LINK indicator of the unit lights up in
orange.
 Play music and adjust the volume.
(AirPlay).
Connect the unit and iPhone/iPad/iPod touch to the same
SSID of your router.
See overleaf for connecting the unit to your Wi-Fi network,
and make sure the LINK indicator of the unit lights up in
orange.
Music is played back.
Music is played back.
PC (Windows Media Player)
You can listen to music using Windows Media Player on the PC with the
unit.
• Refer to the Help Guide for more details.
http://rd1.sony.net/help/speaker/srs-x99/h_zz/
SongPal Link:
For more information about the unit, consult other documents
Enjoy music in any room via Wi-Fi.
You can listen to your favorite music stored in your PCs or mobile
phones and furthermore, music from streaming services, in different
rooms with ultimate sound quality.
Operating Instructions (separate document)
Use the SongPal app installed on your smartphone/iPhone to control
the function.
If you use multiple devices that are compatible with the SongPal Link
function, all devices must be connected to the same Wi-Fi network.
For more details, refer to the Help Guide listed on the right, or the
Wi-Fi Startup Guide supplied with each device.
•• Safety information
•• Parts and controls
•• Wi-Fi network connection using PC
•• Connection/playback method with BLUETOOTH, USB or other
devices
•• About the NFC function
•• Troubleshooting
•• Specifications etc.
Help Guide (web document for a PC/smartphone)
•• Wi-Fi network connection details
•• Linkage with SongPal app
•• Network connection and playback method with each OS/device
•• BLUETOOTH connection and playback method with various devices
•• How to play High-Resolution Audio format files
•• Software update etc.
Help Guide URL:
http://rd1.sony.net/help/speaker/srs-x99/h_zz/
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement