PROFESSIONAL
USE AND CARE INSTRUCTIONS
Model EP905
115V~, 60Hz., 1500 Watts
For information or assistance:
USA: EURO-PRO Corporation
178 West Service Rd.
Canada: EURO-PRO Corporation
4400 Bois Franc
Champlain, NY 12919 St. Laurent, QC H4S 1A7
Tel: 1 866 98SHARK (1 866 987-4275) www.sharkvac.com
IMPORTANT SAFETY INSTRUCTIONS
When using your EURO-PRO Professional Shark Steam Blaster, basic safety precautions should always be observed, including the following:
1.
Read all instructions before using your
Professional Shark Steam Blaster.
2.
Use the system only for its intended use.
3.
To protect against a risk of electric shock, do not immerse any part of the system in water or other liquids.
4.
Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
5.
Do not allow cord to touch hot surfaces.
Let the system cool completely before putting away or before opening the water tank (removing the safety cap) . Wrap power cord loosely around your system when storing.
6.
Always disconnect system from electrical outlet when filling or emptying water tank and when not in use.
7.
Do not operate the system with a damaged cord or plug, or if the appliance or any other part of the system has been dropped or damaged. To avoid the risk of electric shock, do not disassemble or attempt to repair the Professional Shark Steam
Blaster. Return the system to EURO-PRO
Corporation (see warranty) for examination and repair. Incorrect re-assembly or repair can cause a risk of electrical shock or injury to persons when the Professional Shark
Steam Blaster is used.
8.
Close supervision is necessary for any appliance being used by or near children.
Do not leave the system unattended while connected.
9.
Burns can occur from touching hot metal parts, hot water or steam. Do not turn upside down as there may be hot water in the unit. Never direct steam at any person.
The steam is very hot and can cause burns.
10. Do not operate in the presence of explosive and/or flammable fumes.
11. This appliance is intended only for household use. Follow all user instructions in this manual.
12. Never use any chemicals or substance other than tap water in the machine. Use of chemicals may damage the machine. Use of chemicals will automatically void your warranty.
To reduce the risk of fire, electric shock, or injury:
• Do not leave the Professional Shark Steam
Blaster plugged in when unattended. Unplug the electrical cord when not in use and before servicing or refilling water tank.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children, pets or plants.
• Use only as described in this manual. Use only manufacturer’s recommended accessories.
• Do not pull cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls as applicable before unplugging from electrical outlet.
• Turn off all controls before unplugging from electrical outlet.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or steam cleaner with wet hands or operate without shoes.
• Do not put any objects into openings. Do not use with any opening blocked.
• Store your appliance indoors in a cool, dry area.
• Keep your work area well lit.
• When in use, never turn the appliance over or on its side. Never direct steam towards people, animals or plants.
• Do not immerse the steam cleaner into water or other liquids. Always unplug the power cord from the electrical socket when filling the steam cleaner.
• Do NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance as this may damage the unit or make it unsafe for
use. Use regular tap water or distilled/purified water if the tap water in your area is very hard.
SAVE THESE INSTRUCTIONS
For Household Use Only
Rev. 08/02A
1
ADDITIONAL IMPORTANT SAFEGUARDS cont.
1. To avoid circuit overload, do not operate another appliance on the same socket (circuit)
2. If an extension cord is absolutely necessary, a 15 ampere 14 gage cord should be used.
Cords rated for less amperage may overheat. Care should be taken to arrange cord so that it cannot be pulled or tripped over.
3. Do not leave unattended when the system is connected to a power supply/electrical outlet.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
WARNING:
This appliance is equipped with a grounded-type 3-wire cord (3-prong plug). This plug will only fit into an electrical outlet made for a 3-prong plug. This is a safety feature. If the plug should fail to fit the outlet, contact an electrician to replace the outlet. Do not attempt to defeat the safety purpose of the grounding pin, part of the 3-prong plug.
GETTING TO KNOW YOUR PROFESSIONAL SHARK
STEAM BLASTER
12
(Shown Fitted to
Rectangular
Brush)
1.
On/Off Switch
2.
Temperature Ready Light (Green)
3.
Power “On” Light (Amber)
4.
Rectangular Floor/Carpet Brush
5.
Extension Tubes (2)
6.
Flexible Steam Hose
6A. Pistol Grip
7.
Safety/Filler Cap
8.
Small Detail Brush
9.
Glass & Tile Squeegee
10. Concentrator Nozzle
11. Shoulder Strap
12. Angle Adapter
13. Filling Funnel
2
Technical Specifications
Voltage:
Power:
Water Capacity:
Max. Steam Temperature:
Steam Generator:
115V~ 60Hz.
1500 Watts
5 Cups
240°F
Stainless Steel
3
OPERATING INSTRUCTIONS
Components
On/Off Button: To turn the unit “On” and energize the boiler, depress the
“On/Off” control button.To turn the unit off depress the “On/Off” control button once again.
Power “On” Light (Amber): This light will illuminate when the unit is turned ON and will remain on until the unit is turned
OFF.
Safety Cap: In order to open the Safety
Cap turn counter clockwise.
Caution: Read the instruction for “Filling the Water Tank” before opening the
Safety Cap.
Temperature Ready Indicating Light
(Green): When this light is “On”, it indicates that the steam is ready to use.
Note: This light will go “On” and “Off” during usage showing that the steam is being generated.
Starting Your Professional
Shark Steam Blaster
CAUTION:
Do not plug in the machine during filling. Use a grounded receptacle. Use only a heavy duty extension cord rated for 15 amps - Do not use an ordinary extension cord.
IMPORTANT:
Do NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance. Use regular water or distilled/purified water if the tap water in your area is very hard.
Filling Your Professional
Steam Shark With Water
IMPORTANT:
Always insure that the unit is “UNPLUGGED” from the wall receptacle prior to initial filling or re-filling the water tank. Never attempt to fill this unit under
a water tap, always use the filling funnel
provided. Failure to follow these steps will cause the water tank to overfill and may pose an electrical safety hazard.
Step 1: Before filling the Portable steam cleaner, make sure that the unit is NOT plugged in.
Step 2: Turn Safety/Filler Cap counter clockwise until removed.
Step 3: Place Water Filling Funnel in tank and add 1 1/4 quarts
(5 cups) of water. Do not
overfill.
Replace Filler Cap by turning clockwise - press down firmly to tighten. Heating time is approximately 5-8 minutes with cold water. Filling boiler with hot water will shorten heat up time.
Step 4: Plug the unit into a standard
(3-prong) grounded receptacle. The power light will illuminate. Depress
On/Off button.
Step 5: Allow approximately 5-8 minutes for vapor to reach its working temperature and pressure .
When this have been reached, the Green
Temperature Ready Light will go on and the unit is ready to operate.
Step 6: Connect desired attachments into the Flexible Steam Hose.
Note: After you start using steam, the Green Indicator will go on and off intermittently, indicating that steam is being produced.
Step 7: At the start, some water will come out from the nozzle of the attachment. This is unheated water in the hose and is normal.
Important:
When the Professional
Shark Steam Blaster has run out of water, the low-water thermostat will switch off the steam generator. The heater will NOT turn on again until the boiler has cooled down or has been refilled with water again.
Caution:
When refilling the machine while it is still hot, the first drops of water might bubble up. Use caution when opening the Safety/Filler Cap.
4
OPERATING INSTRUCTIONS cont.
Refilling Your Professional
Shark Steam Blaster With Water
Step 1: Turn On/Off Button to “Off”.
Depress the steam switch on the handgrip to ensure that any remaining pressure in the boiler has been released.
Step 2: Disconnect Electrical Power Cord from wall outlet.
Step 3: Carefully loosen the safety/filler cap by pushing down and rotating counter clockwise. Any residual steam will be released below the safety/filler cap if the tank has not been completely vented. When the hissing stops and the last of the steam has been released, remove the filler cap. Allow unit to cool down.
CAUTION:
Allow unit to cool for 5 minutes before refilling. If the Professional
Shark Steam Blaster is still hot, there is a risk that water will be squirted back during filling and cause scalding.
Extreme care should be taken when refilling the unit. Use caution when opening the Safety/Filler Cap as cap may become hot during use and escaping steam can cause scalding
Step 4: Allow the vapor steam cleaner to cool for 5-10 minutes before refilling with water.
Step 5: Refill water tank with water using the filling funnel.
Step 6: Firmly screw the safety/filler cap back onto the unit by turning clockwise and pressing down lightly.
Step 7: Connect power cord to the wall outlet. Press the On/Off Power
Switch to the "On" position and wait until the "Temperature Ready"
(green) light comes on before you continue cleaning.
5
Using Your Unit with Floor Brush
Step 1: Connect one of the extension tubes to the pistol grip on the flexible steam hose. To attach the extension tubes one onto the other or onto the pistol grip, press the locking button ensuring that it fits into the hole. (See illustrations.) To disconnect, repeat the operation by pressing the locking button and pulling the two sections apart.
Locking
Button
Locking
Button
Pistol Grip
Extension Tubes
NOTE:
The angle adapter is usually already attached to the floor brush. Fit floor brush with the angle adapter on to the extension tube.
Step 2: If the angle adapter is not attached to the floor brush, hold the brush with its bristles up in your left hand. With the angle adapter pointing downward, insert it into the hole in the back of the brush, then turn the angle adapter 180°.
Step 3: Insert the electrical power cord into the wall outlet. Press the
On/Off switch to the "On" position. The appliance will now begin to produce steam. Heating time is approximately 5-8 minutes with cold water. Filling the steam generator with hot water will shorten heat up time. The green
"Temperature Ready" light will come on when the steam is ready for use.
OPERATING INSTRUCTIONS cont.
Attaching a Towel to the
Floor Brush
100% white terry cloth towel can be fitted on this brush, so as to absorb the dirt and protect delicate surfaces.
Important:
Please note that bristles may break through thin towels. We recommend that two (2) towels, laid one on top of the other be used. This will ensure that the brush bristles do not break through and that the towels will be sufficiently absorbent and retain as much dirt as possible.
Very Important
: When installing the towels to the floor brush, ensure that the towels do not cover the front and the back of the brush. (See fig. E)
Fig. C
4. Fold the other side of the towel as shown in Fig. C.
Fig. A
1. Prepare white terry cloth towel: size 8” x 17” as shown in Fig. A.
2. Place the brush on top of the towel.
Fig. D
5. Place the corner under the cloth holder as shown in Fig. D.
Open
Fig. B
3. Fold the towel as shown in Fig. B
Open
Fig. E
6. Place the towel around the brush, and repeat folding the towel as shown in Fig. E. When folding the towel, leave some slack. Do not pull tightly around the brush, leave some looseness.
6
OPERATING INSTRUCTIONS cont.
Attaching the Accessories to the Flexible Steam Hose
Dual Edge Glass & Tile Squeegee
This attachment is very useful for cleaning large windows, plastic material, ceramic, tiled or marble surfaces.
To use: Connect the tile squeegee to the pistol grip or use with extension tube for hard to reach surfaces.
Apply steam abundantly, rub with the soft spongy edge, then remove excess water and dirt with the glass wiping edge.
CAUTION:
When cleaning windows, always avoid any sudden changes in temperature to prevent glass breakage or cracks.
Concentrator Nozzle
This attachment is very useful for cleaning surfaces that are difficult to reach. It is ideal for radiators, door and window jambs, shutters and sanitary fixtures. The concentrator nozzle will fit directly onto the pistol grip or may be used with extension tubes
Detail Brush
It is best for cleaning grout in-between the tiles, ceramic and marble.
To use: Push the detail brush on the end of the concentrator nozzle, which may be used directly on the pistol grip or with extension tubes
Tips On How To Use Your
System
Water
• Use tap water for all your cleaning needs.
• However, if you live in an area with hard water, use demineralized / distilled water when steaming light colored fabrics to eliminate the possibility of hard water stains.
IMPORTANT:
Do NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance. Use tap water or distilled/purified water if the tap water in your area is very hard.
Temperature
• The vapor temperature at the tip of the nozzles is between 220°F and
240 °F.
• The temperature of the vapor falls to
100 °F at a distance of 10 inches from the nozzle.
WARNING
: A towel wrapped around the brush can become hot enough to burn. Make sure that you let the towel cool off before touching it.
Using Towels
Note :
We strongly recommend the use of two (2) 100 % cotton towels layered one on top of the other.
• For best results use 100% cotton white terry cloth towels.
• Use correct size (8” x 17”) of towel to allow you to wrap the towel over the ends of the brush and clip it under the spring loaded towel clips.
• The purpose of using towels is to absorb the moisture and dirt being removed. Always use dry towels. A wet towel will smear the dirt.
• Wash towels with strong detergent and bleach.
• Using scented fabric softener while washing the towels will cause the scent to be released into the air when using the towels with your steam system.
Efficient Work
• For vertical surfaces, wipe always from the top down, in this way the dirty water will not soil surfaces already cleaned.
• Avoid changing brushes back and forth while cleaning.
• Start with the smallest brush to clean tight spots and corners first.
• Wipe dirt as soon as possible, otherwise it will dry and re-adhere to the surface.
7
USAGE SUGGESTIONS FOR YOUR STEAM CLEANER
Wood, Vinyl and Marble Floors
Use the floor brush with a 100% cotton terry cloth attached, ( see page 7 for details). Move the brush slowly in back and forth motions. When the towel is soiled, you can turn the towel over or replace it with a clean towel. If you are working on a very dirty area, we recommend that you move the brush over the area slowly, several times. If it is a wood floor, do NOT leave the unit stationary for any length of time to avoid heat or moisture build-up in the wood.
By cleaning with the towel over the brush, you will not affect the shine on the floor.
To Clean Waxed Floors: Install a clean towel(s) on the floor brush, work quickly.
The towel will absorb the dirt but not remove the wax.
Vinyl Floors: Do not allow heat to buildup in any kind of vinyl, since it can soften it enough to affect its texture. Work quickly on vinyl. Use two (2) towels on floor brush.
Tile Floors: For tile and marble floors only, if there is an area of the floor which is excessively dirty, you may remove the towels and agitate the area with the brush bristles directly. Do not let the area dry.
Wipe immediately with a clean cloth. Reclean with brush and towels in place.
Note: Do not use steam cleaner on hardwood or vinyl floor without towels installed on the floor brush.
Upholstery
Use the floor brush attached directly to the hand grip with a clean white terry cloth towel. Use fast, light strokes, avoid getting the fabric wet. Be patient with stubborn spots; work on a spot gently for no more than a minute at a time, then wait five minutes for the area to dry and repeat. Use circular movements or back-and-forth and sideto-side movements to get all sides of surface fibers. Finish with a brushing in one direction that will give the fabric a uniform appearance.
CAUTION:
Always determine the colorfastness of any fabric-especially with reds or blues - by taking a clean, moist, warm towel and gently rubbing a small area as far down on the back or other out of the way place on the furniture as possible. If color comes off on the towel, you may need to have the piece dry cleaned.
Window, Glass Surfaces and Mirrors
Use the dual edge glass and tile squeegee. Work with the vapor jet on using the top to bottom movements. Use the squeegee with the vapor off to clear the water from the glass. To do this without leaving streaks, use lateral movements from the top to the bottom of the surface.
Fiberglass or Stainless Steel Surfaces
Use the floor brush or detail brush. Slowly move the brush over the surface to be cleaned. The vapor will emulsify the dirt and grease on the surface. Follow behind with a terry cloth towel over the brush to remove excess moisture and residue.
Tip: An old idea for polishing stainless steel is to wipe it down with seltzer soda water after it is cleaned.
Soap Scum
Soap scum dissolves almost immediately under a combination of heat and moisture.
Rinse the surface with a small amount of water afterwards or go back over it once more with a clean terry cloth towel.
Note: Soap scum sometimes will develop a hard surface from waterborne minerals. If this is the case, use the floor brush with no towel first to break up this surface - or spray or wipe first with lemon, vinegar or seltzer soda water to soften the minerals.
Moving too slowly can dry out the soap scum and cause it to granulate on the surface. The surface will have a gritty feel.
If this happens, apply vapor to the surface with the open brush again and re-clean.
8
USAGE SUGGESTIONS FOR STEAM CLEANER
cont.
Garden Furniture
Use any of the brushes depending on the surface area. Work quickly when cleaning resin outdoor furniture.
Blinds
Use the detail brush to clean blinds. Move the brush over the surface, allowing enough time for the vapor to penetrate. Work quickly on
PVC blinds. Test for color fastness on fabric blinds before using.
Bathroom Areas
To clean the bathtub or shower area, use the detail brush for grout, shower door tracks, hard to get areas and heavily soiled areas. The dual edge window/tile squeegee will be the most efficient way to clean the rest of the area.
Allow plenty of time for the heat to penetrate the surface. This is especially helpful in the shower area if there is tile or grout.
Removal of soap scum on tile, grout, and shower doors is also easier with the steam cleaner.
To clean sanitary fixtures, use concentrator nozzle with or without detail brush. Use a terry cloth towel or paper towel to wipe up excess moisture and residue.
To clean the sink and faucets, use detail brush.
Exterior Areas
To clean inside your car, use the floor brush with a terry cloth towel attached to clean upholstery and interior areas just as in the home. You should not expose the bristles to leather - use only the brush with the terry cloth towel attached. For detailing the wheels, use the concentrator nozzle and the detail brush.
Exterior windows are cleaned best by applying the vapor with the concentrator nozzle and following with a paper towel.
To clean bicycles, use the detail brush.
To clean equipment, use the detail brush, depending on the surface area.
Artificial Plants
Use the concentrator nozzle without a brush attached to blow off the dust and dirt.
Clothing
A vapor cleaning system is excellent for removing wrinkles from fabrics. Simply
“vaporize” the surface from a distance (12”-18”)
The dry vapor removes wrinkles without leaving the fabric wet like ordinary fabric steamers do.
Nicotine and Tar
Nicotine and tar dissolves at high temperatures and becomes a light yellow oil that has the consistency of sewing machine oil. When the nicotine/tar film is touched by a hot terry cloth towel clipped over the floor brush, it immediately dissolves and flows into the towel.
You can remove it from flat surfaces as fast as you can move the brush over the surface.
Removing Wax, Tar, Etc.
Many stains are only stuck on the surface of materials and can be easily and quickly removed by “blowing” excess material away from the surface from the side. This is accomplished by using the concentrator nozzle. Hold the terry cloth towel to the side to catch the loose residue as it is blown by the nozzle. Note: Always vacuum any loose residue off the surface before you apply vapor to it.
Hints
The steam cleaner has many uses that have not been mentioned. This was meant only to give you a general idea of what can be achieved with the unit. However, the ways in which to use the attachments and brushes are in most cases universal. It is most helpful to always have a terry cloth towel or paper towel ready to use for removal of moisture and residue. 100% white cotton towels work best.
You can clean the brushes with your steam cleaner. To clean the floor brush, hold at one end and use the concentrator nozzle to simply blow off dirt into the garbage can. When cleaning the detail brush, use a pair of pliers to hold and blow dirt as above or place in the basket of your dishwasher.
Note: Wipe immediately before the cleaned area dries. When cleaning the oven, use the detail brush to clean around the elements and drip trays. Use the detail brush for cracks, crevices, and hard to reach areas.
Refrigerator - Use the concentrator nozzle to blow away dirt in the ice machine and on door seals. The vapor will not dry out or crack the seals as chemicals often do. Can openers and other kitchen equipment can be easily cleaned with the detail brush on the nozzle to get into all the nooks and crannies. Mold stains around door gaskets can be removed with the detail brush.
To clean microwaves or other small
appliances use the detail brush for small areas .
Note: When cleaning small electrical appliances always unplug them from outlet before cleaning.
To clean counter tops, use the floor brush with a terry cloth towel attached. For heavily soiled areas, use the brush without the terry cloth towel first in order to loosen the debris, then follow with a terry cloth towel attached to finish.
9
CARE & MAINTENANCE
If you consistently use demineralized or distilled water, cleaning the tank is unnecessary.
Rinsing out the steam cleaner:
Normally, a periodic rinse of your
Professional Steam Shark will free it from deposits. This is recommended every 10-
15 tankfulls, to free up any scale deposits from the tank.
Fill the boiler with water and shake the cleaner vigorously. Tilt the cleaner upside down to empty the boiler of water and any scale deposits.
Descaling your steam cleaner:
If the tap water in you area contains a high level of calcium deposits and you have been using tap water to do your steam cleaning, your should descale your unit after 10-15 tankfulls.
Step 1: Unplug the steam cleaner from the power source before you descale the boiler.
Step 2: Fill the boiler with 1 part (6 oz.) vinegar and 4 parts (24 oz.) water and leave overnight or for a period of approximately 8 hours. Do not screw the safety/filler cap onto the steam cleaner while you are descaling the boiler. Do not use the steam cleaner while descaling solution is inside the boiler.
Step 3: After the period of soaking, turn the steam cleaner upside down to empty solution from the boiler. Due to the fact that a small amount of solution will be left in the boiler, it is necessary to rinse the boiler out with clean water 2 or 3 times. Your steam cleaner is now ready for use.
Attaching the Shoulder Strap
Using the detachable shoulder strap allows for greater freedom of movement when both hands are needed for various cleaning tasks.
To attach the shoulder strap to the steam cleaner, simply snap the shoulder strap hooks onto the connecting rings on the unit body.
See illustrations below.
When using the Professional Steam
Shark with the shoulder strap, avoid rocking or tilting the unit excessively as this may cause water to enter the hose and be discharged along with the steam.
10
Model EP905
1 YEAR LIMITED WARRANTY
EURO-PRO Corporation warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of purchase when utilized for normal household use by the original purchaser only. The attached Warranty Registration Card must be filled out and returned within 10 days of purchase. This is essential for your Warranty to be effective should any problem arise with this product.
Should any defect covered by the terms of the limited warranty be discovered within one year, EURO-
PRO Corporation will repair or replace any defective part provided the unit is returned by the original purchaser, freight prepaid, to:
In US: EURO-PRO Corporation, 178 West Service Rd., Champlain, N.Y. 12919
In Canada: EURO-PRO Corporation, 4400 Bois Franc, St. Laurent, QC, H4S 1A7
Proof of purchase date and $12.95 for handling and return packing/shipping charges must be included.*
The liability of EURO-PRO Corporation is limited solely to the cost of the replacement parts or the complete unit at our option. LABOUR CHARGES ARE NOT INCLUDED.
This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, negligent handling, or damage due to faulty packaging or mishandling in transit (by any common carrier).
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Corporation , if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO
Corporation liable for incidental or consequential damages of any nature whatsoever. Some States do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights which vary from state to state.
PURCHASER___________________________________________________________
DATE OF PURCHASE ___________________________________________________
DEALER ______________________________________________________________
*important: Carefully pack item to avoid damage in shipping. Be sure to attach tag to item before packing with your name, complete address and phone number with note giving purchase information, model number and what you believe is the problem with item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.
OWNERSHIP REGISTRATION CARD
Please complete and return within ten (10) days of purchase in order to validate the foregoing Limited
Warranty.. The registration will enable us to contact you in the event a product defect is discovered. By returning this card you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions .
RETURN TO: EURO-PRO Corporation, 178 WEST SERVICE RD., CHAMPLAIN, N.Y. 12919
In Canada: EURO-PRO Corporation, 4400 Bois Franc, St. Laurent, QC, H4S 1A7
PURCHASER: ……………………………………..…………………………………………………
ADDRESS: ………………………………………...……………………………………………….
CITY: ……………………………….. STATE/PROV:………………………………………….
NAME AND ADDRESS OF DEALER: …………………………………………………………..
Printed in Italy
11
