Magnadyne LS4000S LS4001W Owner`s manual

Magnadyne LS4000S LS4001W Owner`s manual
LS4000CDINS
6/17/05
2:48 PM
Page 1
OWNER'S MANUAL
LS4000W, LS4000B, LS4000S
LS4001W, LS4001B, LS4001S
AM/FM Stereo Receiver and Compact Disc Player
Designed for In-Wall Installation of All Recreational Vehicles, Motor Homes and Mobile Housings
12 Volts DC
®
U.S. Patent No. D502, 461
A Registered Trademark of Magnadyne Corporation
LS4000CDINS
6/17/05
2:48 PM
Page 2
INTRODUCTION
WARNING! To prevent fire or electrical shock hazard, do not
expose this product to rain or moisture, or remove cover or
bottom screws. No user serviceable parts inside. Refer servicing
to qualified service personnel.
Please read all of the information in this booklet before using
this unit to insure that you fully understand the capabilities of
this unit.
CONTROLS AND FUNCTIONS
5
8
15 11
16 17 10
REPEAT
ALL
9
6
7
2
3
12
1
14
4
2
13
LS4000CDINS
6/17/05
2:48 PM
Page 3
CONTROLS AND FUNCTIONS
1. Power Button (PWR)
Press this button in to turn the unit on. Press again to turn the
unit off.
9. Skip Up Button (
)
To skip to the next higher track on the compact disc, press this
button.
2. AM/ FM Button
Press the button to select the desired AM or FM radio band.
10. Program Button
Use the program button to arrange the tracks on the disc to
play in the order you wish. (See compact disc operation)
3. CD / Tuner Button
Press this button to select the desired playing mode either
AM/FM radio or CD player.
11. Dial Indicator
The dial indicator will move up and down the scale as you
rotate the tuning knob (4) indicating the station you are
listening to.
4. Radio Station Tuning Knob
Rotate this knob to locate the radio station that you desire.
Rotating it clockwise will take you up the frequency band and
rotating it counter-clockwise will take you down the frequency
band.
12. Tone Button
This button will tailor the overall tone of the unit. Pushing the
button in will achieve lower tones and pushing the button
again will achieve higher tones.
5. Compact Disc Door
By pressing the compact disc door next to the word “PUSH”
the door will open to allow you to insert a compact disc.
13. Volume Control Knob
Rotate this knob clockwise to increase the volume of the unit.
6. Play/ Pause Button (
)
After inserting a compact disc press this button to begin compact disc play. Pressing this button again will stop the compact
disc until the button is pressed again.
14. Speaker A , B and A+B Selector
To play the "A" set of speakers, slide the selector to the
"Speaker A" position. To play the "B" set of speakers, slide
the selector to the "Speaker B" position. To play the "A" and
"B" speakers at the same time, slide the selector to the
center position.
7. Stop Button ( )
When this button is pressed, compact disc play will stop.
15. Compact Disc Display
This display contains all the information about the disc that is
playing and all the modes the disc can play under. (See
compact disc operation).
8. Skip Down Button (
)
To skip to the next lower track on the compact disc, press this
button.
3
LS4000CDINS
6/17/05
2:48 PM
Page 4
CONTROLS AND FUNCTIONS
Compact Disc Operation:
16. Random Button
Use the random button to play the disc tracks in a random
order selected by the disc player's computer.
1. Press the PWR button (1) in to turn the unit on.
2. Press the CD/TUN button (3) to select CD operation.
3. Press the door (5) and gently pull the compact disc door
open fully.
4 Insert a disc onto the disc hub and press gently in the center
until the disc is secure and supported by the hub.
5. Close the compact disc door until it snaps into place. Allow
10 seconds for the system to read the disc.
6. Use the skip down button
(8) or skip up button
(9) to
select a specific track.
7. Press the play button
(6) and adjust the volume and tone
controls as desired.
8. Press the stop button
(6) to stop disc play.
17. Repeat Button
Use the repeat button to continuously play one song repeatedly or to continuously play the entire disc repeatedly.
Radio Operation:
1. Press the PWR button (1) in to turn the unit on.
2. Press the CD/TUN button (3) to select radio operation.
This Area Lights
Up for CD
Operation
REPEAT
This Area Lights
Up for Radio
Operation
ALL
3. Press the AM/FM button (2) to select either the AM or FM
radio band.
4. Tune in the desired radio station by rotating the tuning knob (4).
5. Adjust the VOLUME (13) and TONE (12) as desired.
Warning ! Never touch the laser eye. Moisture and oils from
your fingers can impair proper operation.
FM Stereo Operation:
The unit will automatically switch from FM mono to FM stereo
when the signal strength increases to a stereo level. If the signal should become weak on stereo reception, the unit will
switch back to the mono mode.
4
LS4000CDINS
6/17/05
2:48 PM
Page 5
CONTROLS AND FUNCTIONS
Using the Compact Disc Program Feature:
Using the Compact Disc Random Feature:
If you desire to have the song selection of the disc played in a
different order than arranged on the disc, repeat the following
procedures to program the playing order.
The random feature allows the disc player to select and play the
songs on the disc in random play order.
1. To initiate the random feature, insert a disc and close the CD
door. Press the RANDOM button (16) before pressing the play
button (6). Press Play (6) and the disc will play.
1. When the CD disc is stopped, press the PROGRAM button
(10). The PGM indicator will be displayed (15).
REPEAT
ALL
PGM
Indicator
PGM
2. Use the skip down button
(8) or skip up button
(9) to
select a specific track Press the program button to lock in the
selection.
REPEAT
ALL
3. Repeat step #2 to program the the listening order of the tracks
on the disc, you can program up to a maximum of 21 tracks.
2. To turn off the random function press the RANDOM button (16)
once again.
4. After all the tracks required are programmed, press the
PROGRAM button (10) once again to lock the program.
The compact display will then display the play order you
programmed.
5. Press the play button
Note: You can activate and deactivate the random feature at any
time by pressing the RANDOM button (16).
(6) to play the new program.
Note 1: Pressing the Stop button (7) will stop the play function
but will not erase the program sequence. Press the PROGRAM
(10) button, then the Play button (6) once again this will start the
play/program function from the first programmed track.
Note 2: Opening the CD door, changing the source selection
to AM/FM or shutting the power OFF on the unit will clear the
program memory.
5
LS4000CDINS
6/17/05
2:48 PM
Page 6
CONTROLS AND FUNCTIONS
Using the Repeat Feature:
Handling the Disc:
The repeat feature has two modes of operation. A single track can be
continuously repeated or the entire disc can be continuously repeated.
1. When inserting the disc, hold the disc with your thumb, middle
finger and index finger and press the center with your index finger.
2. When removing the disc, always pull at the left or right edge of
the disc until it snaps loose
from the disc hub. There are
indentations in the plastic for
your fingers at these points.
3. Always keep your discs clean
and free from scratches,
fingerprints and dirt.
Repeating Single CD Track:
Press the REPEAT button (17) one time while a CD is playing.
"REP" will be flashing in the compact disc display (15) area.
The song will repeat continuously.
FM 88
AM 53
92
92
98
100
104
130
108 MHz
171 x10 KHz
REPEAT
R
REPEAT
INTRO
PROG
ALL
TUNING
REPEAT
ALL
VOL
MIN
MAX
A
Repeating Entire CD:
Press the REPEAT button (17) two times while a track is
playing. "REP" will be indicated on the compact disc display
(15) area. The disc will play all the way through to the last
song and then repeat to the first song continuously.
2x
REPEAT
ALL
Cancelling Repeat Feature:
To turn off the repeat feature, press the repeat button (17) a
third time (the REP1 or REP indicator will be off in the display).
AM 53
92
100
130
171
3x
REPEAT
ALL
6
LS4000CDINS
6/17/05
2:48 PM
Page 7
INSTALLATION
End Caps
Caution: Do not install radio without rear
cover installed. No user-serviceable parts
inside. Rear cover provides protection
against potential fire hazard.
7
LS4000CDINS
6/17/05
2:48 PM
Page 8
POWER CONNECTIONS
This unit for use only with a 12 volt DC power
source with a negative ground.
RED Wire (+)
To 12 Volt DC Power
BLACK Wire (-) Ground
8
LS4000CDINS
6/17/05
2:48 PM
Page 9
SPEAKER CONNECTIONS
Left Speaker (A)
Right Speaker (A)
+
+
_
_
BROWN Wire
GRAY Wire
ORANGE Wire
WHITE Wire
_
_
GREEN Wire
BLUE Wire
+
Left Speaker (B)
+
Speaker Connections: Do not confuse the A and B speaker sets
9
Right Speaker (B)
LS4000CDINS
6/17/05
2:48 PM
Page 10
ANTENNA CONNECTIONS
External Automotive
Type Antenna Socket
Either
or
External Automotive
Type Antenna (Not Provided)
DP36AXT In-Wall Antenna (Not Provided)
If an automotive antenna is not available or is undesired, we
recommend the use of a Magnadyne DP36AXT di-pole antenna substitute. Plug the male plug from the DP36AXT into the
female receptacle of the LS4000 or LS4001 unit and allow the
cable of the antenna to lay inside the wall.
The LS4000 and LS4001 have a provision for a standard automotive antenna. If an automotive antenna is used, plug the
male plug from the antenna into the female receptacle provided on the unit.
10
LS4000CDINS
6/17/05
2:48 PM
Page 11
SAFETY INSTRUCTIONS
Outdoor Antenna Grounding: If an outside antenna is connected to the receiver, be sure the antenna system is grounded
so as to provide some protection against voltage surges and built
up static charges. Section 810 of the National Electrical Code,
ANSI/NFPS no. 70-1983, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. See figure 1.
Read Instructions: All the safety and operating instructions
should be read before the appliance is operated.
Retain Instructions: The safety and operating instructions
should be retained for future reference.
Heed Warnings: All warnings on the appliance and in the
operating instructions should be adhered to.
Follow Instructions: All operating and use instructions should
be followed.
Object and Liquid Entry: Care should be taken so that objects
do not fall and liquids are not spilled into the enclosure through
openings.
Water and Moisture: The appliance should not be used near
water-- for example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool, etc.
Example of Antenna Grounding as per
National Electrical Code. Instructions
Contained in Artical 810-"Radio and
Television Equipment"
Wall or Ceiling Mounting: The appliance should be mounted to
a wall or ceiling only recommended by the manufacturer.
Antenna Lead-In Wire (B)
Heat: The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
Mast
Ground
Clamp
Power Supply: The appliance should be connected to a power
supply only of the type described in the operating instructions or
as marked on the appliance.
Ground
Wire
(A,B)
Cleaning: The appliance should be cleaned only as recommended
by the manufacturer.
Antenna Discharge
Unit (C)
To Receiver
Grounding
Clamps
Figure 1.
2.44 Meters
Power Lines: An outdoor antenna should be located away from
power lines.
Grounding Electrode
Drivin 8' Into the Earth
A) Use No. 10 AWG (5.3mm2) copper, No 8 AWG (8.4mm2) aluminum, No. 17
AWG (1.0mm2) copper clad steel or bronze wire, or larger, as ground wire.
B) Secure antenna lead-in and ground wires to house with stand-off insulators
spaced from 4 feet (1.22m) to 6 feet (1.83m) apart.
C) Mount antenna discharge unit as close as possible to where lead-in enters
house.
11
LS4000CDINS
6/17/05
2:48 PM
Page 12
OPERATION AND MAINTENANCE
WARRANTY
Damage Requiring Service: The appliance should be serviced by
qualified service personnel when:
ONE (1) YEAR LIMITED WARRANTY
Magnadyne Corporation or its authorized agents will within 1 year from the date
of sale to you, repair, replace or refund the retail sales price of said product or any
part thereof, at the option of the Magnadyne Corporation or its authorized
agents, if said product or part is found defective in materials or workmanship,
when properly connected and operating on the correct power requirements
designated for the specific product. This warranty and Magnadyne Corporation
or its authorized agents obligations hereunder do not apply where the product
was; damaged while in the possession of the consumer, subjected to
unreasonable or unintended use, not reasonably maintained, utilized in
commercial or industrial operations, or serviced by anyone other than
Magnadyne Corporation or its authorized agents, or where the warning seal
on the product is broken or the power and/or plugs are detached from the unit.
Magnadyne Corporation or any of its authorized agents will not assume any
labor costs for the removal and re-installation of any product found to be defective,
or the cost of transportation to Magnadyne Corporation or its authorized
agents. Such costs are the sole responsibility of the purchaser.
This warranty does not cover the cabinet appearance items or accessories
used in connection with this product, or any damaged to recording or
recording tape, or any damage to the to the products resulting from
improper installation, alteration, accident, misuse, abuse or acts of nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL
NOT BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES OR CLAIMS EXCEPT THOSE ACCORDED BY LAW. NO
EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT
THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND
BEYOND 1 YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not
transferable.
Some states do not allow limitations on how long an implied warranty lasts,
and some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may
have other rights that vary from state to state.
Defective merchandise should be returned to the original point of purchase or
secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA
90220. A Return Authorization must be obtained before sending any product, or
merchandise may be refused.
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has spilled into the appliance;or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits
a marked change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
Servicing:
The user should not attempt to service the appliance beyond that
described in the operating instructions. All other servicing should
be referred to qualified service personnel.
Caution:
Compact disc should be stored in a container or vinyl bag to
prevent contamination. Disc should not be placed in locations
exposed to sunlight or heat.
Warnings
Handle CD’s
Properly
Do Not Touch
CD’s
Do Not Get Dirt
on CD’s
Do Not Write on
CD’s
104 F
40 C
Do Not Scratch
CD’s
Keep Below 1040
Fahrenheit
Do Not Bend CD’s
LS4000CDINS Rev. E 6-13-05
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement