NuAire MRXBOXAB-ECO4-AESC Installation Manual

MRXBOXAB-ECO4-AESC (Standard Hand Unit)
MRXBOXAB-ECO4-AEOHSC (Opposite Hand Unit)
MRXBOXAB-ECO4-AESW (Standard Hand Unit)
MRXBOXAB-ECO4-AEOHSW (Opposite Hand Unit)
Mechanical Ventilation Units with Heat Recovery for Wall Mounting
Installation Manual
EMC Directive
2014/30/EU
LVD Directive
2014/35/EU
1.0 SAFETY INFORMATION
•
•
•
•
•
•
•
•
The provision of the electrical supply and the connection of the unit to the mains must be
carried out by a qualified electrician.
Isolate from power supply before removing any covers. During installation / maintenance ensure
all covers are fitted before switching on the mains supply.
All-pole disconnection from the mains as shown in the wiring diagram must be incorporated
within the fixed wiring and shall have a minimum contact separation of 3mm in accordance with
latest edition of the wiring regulations.
This unit must be earthed.
Ducting must be securely fixed with screws to the spigot to prevent access to live parts. Duct
runs terminating close to the fan must be adequately protected by suitable guards.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
Precautions must be taken to avoid the back-flow of gases into the room from the open flue of
gas or other fuel-burning appliances.
This appliance should not be used by children or persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge, unless they have been given supervision
or instruction concerning the safe use of the appliance by a person responsible for their safety.
Children shall not play with the appliance. Cleaning and user maintenance shall not be carried
out by children.
1.1 Hazard Symbols
REFER TO INSTRUCTION MANUAL
Read and understand the installation and maintenance manual before installing, operating or maintaining this product.
1.2 Important Information
1.3 Personal Protective Equipment
This manual contains important information on the safe and
appropriate assembly, transport, commissioning, operation,
maintenance, disassembly and simple troubleshooting of the product.
The following minimum Personal Protective Equipment (PPE) is
recommended when interacting with Nuaire product:
While the product has been manufactured according to the accepted
rules of current technology, there is still a danger of personal injury or
damage to equipment if the following general safety instructions and
the warnings contained in these instructions are not complied with.
•Read these instructions completely and thoroughly before
working with the product.
•Keep these instructions in a location where they are accessible
to all users at all times.
•Always include the operating instructions when you pass the
product on to third parties.
•Protective Steel Toed Shoes - when handling heavy objects.
•Full Finger Gloves (Marigold PU800 or equivalent) - when
handling sheet metal components.
•Semi Fingerless Gloves (Marigold PU3000 3DO or equivalent)
- when conducting light work on the unit requiring tactile
dexterity.
•Safety Glasses - when conducting any cleaning/cutting operation
or exchanging filters.
•Reusable Half Mask Respirators - when replacing filters which
have been in contact with normal room or environmental air.
Nuaire would always recommend a site specific risk assessment by a
competent person to determine if any additional PPE is required.
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
16. 03. 21. Document Number 671863
1
MRXBOXAB-ECO4-AE(SC/SW)
Installation Manual
2.0 INTRODUCTION
3.1 Transport Fixings
The ECO4-AE wall mounted range of units are designed to offer
improved sound levels and an aesthetically pleasing installation by
housing a Mechanical Ventilation with Heat Recovery (MVHR) unit
inside an acoustically lined enclosure.
To prevent damage during transit and installation, the product is
shipped with two transportation brackets, these are attached to the
upper screws of the MVHR front panel (Figure 3). These brackets must
be removed before use, failure to do so will result in excessive vibration
and noise. The screws securing the bracket to the side panel of the
enclosure can be removed and discarded, the remaining screws securing
the bracket to the MVHR unit can be loosened allowing the bracket to
be removed before fully tightened to secure the panel in place.
The MVHR unit is fitted with two independent fans to provide
mechanical supply and extract ventilation, each fan has full speed
control for background and boost ventilation rates. To recover heat
from the extract air, the heat exchanger block is utilised. The heat
exchanger can recover up to 95% of the normally wasted heat.
Bypass operation can be disabled via a manual switch in colder months
so the unit recovers heat continually.
3 Transport Fixings
Transportation
bracket
A
A
1 Airflow Through unit (Standard Hand Unit)
Exhaust air
Exhaust
air
from house
from
house
to outside
to outside
Intake air
Intake
air
from outside
from outside
Supply air
Supply
air
to house
to house
Extract air
Extract
air
from house
from house
3.2 Floor Mounting (Recommended)
Due to the size and weight of the unit, floor mounting is the preferred
mounting method, if this is not possible a solid wall is required. A
gypsum block/plasterboard wall will not suffice, examples of suitable
installations are shown in this document.
2 Airflow Through OH unit (Opposite Hand Unit)
Supply air
Supply
air
to house
to house
Extract air
Extract
air
from house
from house
Exhaust air
Exhaust
air
from house
from
house
to outside
to outside
Intake air
Intake
air
from outside
from outside
The unit is not supplied with any mounting brackets; a suitable
mounting structure with means of securing the unit in place is required.
Four female M8 fixing points are available in the base panel of the
enclosure to be used to secure the unit in place, for details of these
along with compulsory support areas and features that should be
accommodated within the mounting structure (Figure 5).
No part of the enclosure should be in contact with the building
structure, the only components that should be in contact are those
used to provide the mounting structure.
Care must be taken to ensure the unit is installed true in all 3
dimensions. Failure to do so may result in overflow from the
internal condensation drip tray.
3.3 Optional Solid Wall Mounting
3.0 MECHANICAL INSTALLATION
Installation must be carried out by competent personnel in accordance
with the appropriate authority and conforming to all statutory
governing regulations. All mains wiring must be in accordance with the
current I.E.E. Regulations, or the appropriate standards. Ensure that the
mains supply (Voltage, Frequency and Phase) complies with the rating
label.
A clear working space is required around the installed unit to allow the
cover to be removed and provide sufficient access for maintenance
such as filter change. A minimum of 480mm is required in front of
the unit.
The fan must be installed indoors, on a suitable wall away from direct
sources of frost, heat and water spray or moisture generation. For a
vibration-free result the unit must be mounted to a solid wall.
The unit must remain switched on at all times to maintain
ventilation within the dwelling. Turning the unit off will cause long
term damage to the unit and building fabric.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a
person for their safety. Children should be supervised so that they
do not play with the appliance.
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
The MVHR unit fixed to a solid wall construction using a suitable
mounting structure (supplied by others).
4 Typical example of a cupboard mounted unit fixed to a
block work wall.
Ducting in the
ceiling void.
Side view of unit
mounted on the
solid wall in a
cupboard using
suitable mounting
structure.
MVHR-DRAIN
Condensate drain,
uninsulated drain
pipe with min 5 o fall
running to SVP.
Valve in ceiling.
Unit weight
= 80kG
Mounting frame
not supplied
16. 03. 21. Document Number 671863
2
MRXBOXAB-ECO4-AE(SC/SW)
Installation Manual
5 Mounting Points
726
43
43
2x Rivet Heads
60
4x M10 Flanged head bolts
protruding from base to be
accomodated in structure design.
2x Hatched regions details
compulsory support areas,
further support may be required
depending on structure design
(supplied by others).
=
=
21
143
410
100 
=

4x M8 Mounting Points
38
70
=
Condensate drain connection
(standard hand configuration).
For opposite hand configuration position
will be mirrored to the other side.
Summer / Winter Cable entry point.
48
48
Mains Cable Connection
3.4 Condensate Drain
Note:
Any Items being accomodated in structure design should
include sufficient clearance to allow for assembly tolerances
and for ease of installation when positioning on site.
6 Condensate Connection
An additional straight multi-fit connector is included with the ancillary
items supplied to extend the condensate drain connection of the MVHR
unit outside the enclosure. The threaded connector should be coupled
to the corresponding connection of the MVHR unit through the square
cut out in the base panel of the enclosure. Care should be taken to not
over tighten this joint as this may result in the inner drain connection
coming loose making removal difficult if required in the future.
The threaded nut can then be removed from the multi-fit connector
and the adhesive backed cover plate passed over the multi-fit
connector and affixed to the enclosure base panel (Figure 6).
•The condensate must be discharged under a water level in a U-trap
drainpipe or an alternative drain method which acts as an airlock.
•The condensate discharge drain is a 32mm male threaded
connection.
B
Cover Plate
Multi-fit
Connector
•If using a U-trap, please ensure the U-trap has been filled to a
suitable level of water to avoid any air locks.
•If the condensation pipe is fitted in an unheated space the pipe
should be in insulated to prevent freezing.
B
Enclosure
Base Panel
7 Condensate Trap Installation
Nuaire recommend MVHR-DRAIN be used as the primary
condensate take-off (Figures 8 and 9).
3.5 Extract / Input Areas
The unit is designed to extract air from all wet rooms e.g. bathroom,
kitchen, en-suite, utility room (with sink). WC’s do not need to be
ventilated if openable windows are fitted.
Supply air should be to all habitable rooms e.g. bedrooms and lounge.
Extract / input grilles should be adjustable valve types (not supplied).
External grilles are to have a minimum free area of 12,250 mm2.
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
Min 5 o Drop
Condensate pipe connection to
unit and a typical example of a
“U” trap drainpipe (Standard
configuration only).
16. 03. 21. Document Number 671863
3
MRXBOXAB-ECO4-AE(SC/SW)
Installation Manual
8 MVHR-DRAIN Installation
3.7 Ventilation Flow Rates
Any air intake terminal must be installed in accordance with the
appropriate regulation. As a guide, the BS5440 series of British
Standards deals with this issue and currently states that an air
intake must be at a minimum distance of 300mm from a gas
boiler balanced flue. Installers are advised to be aware of the
requirements of this standard when installing ‘through the wall’
supply air ducting.
Collar
Condensate drain,
uninsulated drain pipe with
min 5° fall running to SVP.
3.7.1 ADF 2010 Extract Ventilation Rates
Whole Dwelling Ventilation Rates
Number Of Bedrooms In Dwelling
9 "T" Piece CONTRAP &
MVHR Drain Connection
MVHR Drain
To CONTRAP
To unit
To SVP
“T” piece
When using a “T” Piece to connect the CONTRAP drainage and
the MVHR drain pipework the MVHR drain must always be fitted
before the “T” Piece to prevent condensate from feeding back into
the MVHR system.
Whole dwelling
ventilation rate
(l/s)1,2
If the enclosure is to be used in conjunction with an ancillary
distribution box (MRXBOX-DB4) refer to additional assembly
instructions supplied with the MRXBOX-DB4 as requirements will
differ.
2
3
4
5
13
17
21
25
29
1. In addition, the minimum ventilation rate should be no less than 0.3
l/s per m² of internal floor area. (This includes all floors, e.g. for a twostory building add the ground and first floor areas).
2. This is based on two occupants in the main bedroom and a single
occupant in all other bedrooms. This should be used as the default
value. If a greater level of occupancy is expected add 4 l/s per occupant.
3.7.2 Whole Dwelling Ventilation Rates
ADF 2010 - Extract Ventilation Rates
3.6 Ducting
Before commencing ducting installation, reference should be made
to building regulations document “Domestic ventilation compliance
guide”. This document supports ADF2010 and details installation,
testing and commissioning of all ventilation systems.
1
Room
Minimum High rate
Kitchen
13 l/s
Utility Room
8 l/s
Bathroom
8 l/s
Sanitary
Accommodation
6 l/s
Minimum Low Rate
Total extract rate
should be at least
the whole dwelling
ventilation rate given
in table 2.
Otherwise fit 4x 200mm diameter spigots with the M4 screws supplied
to the spigot fixings plates found on the top panel of the enclosure, a
bead of silicone should be applied between the two mating faces to
prevent leakage.
It is recommended that rigid ducting be used at all times. Flexible
ducting has a very high resistance and it is impossible to calculate
how much resistance will be on a system if used. If used the flexible
ducting must be kept to a minimum and should always be pulled taut.
A maximum of 300mm should be used on each leg.
To prevent condensation on the outside of the outside air inlet duct and
the air outlet duct from the unit, these ducts should be insulated.
Ducting must be installed in such a way that resistance to airflow is
minimised. Bends should be kept to a minimum. A minimum distance
of 300mm between the appliance and any bends in ductwork is
recommended.
Ideally 150mm diameter or 220 x 90mm rectangular ducting should be
used (refer to dwelling design drawing, Figures 11 & 12).
Ducting joints must be sealed with silicone type sealant and shall be
adequately and reliably fixed to the appliance.
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
16. 03. 21. Document Number 671863
4
MRXBOXAB-ECO4-AE(SC/SW)
Installation Manual
3.8 ADF 2010 Ventilation Calculations Design of MVHR
Systems
Step 3: The required airflow rates are as follows:
•The maximum whole dwelling extract ventilation rate (e.g. boost)
should be at least the greater of step 1 and step 2. Note that the
maximum individual room extract rate should be at least those
given in ADF 2010 - Extract Ventilation Rates table.
The MVHR system has been sized for the winter period. Additional
ventilation may be required during the warmer months and it has
been assumed that the provisions for purge ventilation (e.g. openable
windows) could be used.
Step 1: For any design air permeability, determine the whole dwelling
ventilation supply rate from Whole Dwelling Ventilation Rates table.
•The minimum air supply rate should be at least the whole building
ventilation rate found in step 1.
For Scotland refer to BRE Digest 398.
As an alternative where the design air permeability is intended to be
more than (>) 5m3/(h.m2) 50 Pa, allow for infiltration for all dwelling
types by subtracting from the whole dwelling ventilation supply rate
from Whole Dwelling Ventilation Rates table; 0.04 x gross internal
volume of the dwelling heated space (m3).
For further information refer to “Domestic Ventilation Compliance
Guide” www.planningportal.gov.uk/buildingregulations/approved
documents/partl/compliance.
Step 2: Calculate the whole dwelling extract ventilation rate by
summing the individual room rates for ‘minimum high rate’ from ADF
2010 - Extract Ventilation Rates table.
MRXBOX units are designed to ventilate the whole dwelling and must
not be used during site construction or the clean-up period. Cement
and plaster dust can be abrasive and can affect fan performance
and reliability. Please ensure that the filters are checked prior to
commissioning to ensure there is no build-up of dust or debris.
3.8.1 Pre Commissioning MRXBOX MVHR Units
(For sanitary accommodation only, as an alternative, the purge
ventilation provisions given in ADF 2010 can be used where security is
not an issue. In this case ‘minimum high extract rate’ for the sanitary
accommodation should be omitted from the step 2 calculation).
While the property is drying out, very high moisture levels are likely
to occur. Therefore it is advisable that if the installation and building
works are complete the unit is left running. If the building works are
not complete please close the air valves or cover up the air valves to
prevent condensation forming in the ductwork and the MRXBOX unit
due to natural migration of warm air.
3.9 Dimensions (mm)
10 Unit Dimensions
485
200
290
191
819
52
If ancillary distribution box MRXBOX-DB4
is to be used, refer to documentation
supplied with MRXBOX-DB4 for additional
information as requirements will differ.
Condensate drain position for
standard hand configuration.
For opposite hand configuration,
position will be mirrored to other side.
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
788
672
16. 03. 21. Document Number 671863
5
MRXBOXAB-ECO4-AE(SC/SW)
Installation Manual
3.10 Ducting Arrangements - Standard Unit Configuration
3.10.1 Circular Ducting
11 Typical Circular Ducting Arrangement For Wall Mounted Units
Exhaust air from
kitchen/bathroom to
outside via louvre grille.
Minimum distance as specified
in building regulations.
*Insulated
extract duct.
Top of ceiling void.
Air supply
to lounge
via Air Valve
in ceilings.
Intake air
from outside
via louvre grille.
All duct between MVHR
unit and atmosphere to
be insulated*.
*Insulated
supply duct.
Extract air
from
kitchen/
bathroom
via Air Valve
in ceilings.
Air supply to
bedrooms
via Air Valve
in ceilings.
Nuaire
MVHR unit.
MVHR-DRAIN
Condensate drain, uninsulated
drain pipe with min 5 o fall running to SVP.
3.10.2 Rectangular Ducting
12 Typical Rectangular Ducting Arrangement For Wall Mounted Units
*Insulated
extract duct.
Exhaust air from
kitchen/bathroom to
outside via air brick.
Minimum distance as specified
in building regulations.
Top of ceiling void.
Air supply
to lounge
via Air Valve
in ceilings.
Intake air
from outside
via air brick.
All duct between MVHR
unit and atmosphere to
be insulated*.
Air supply
to bedrooms
via Air Valve
in ceilings.
Extract
air from
kitchen/
bathroom
via Air Valve
in ceilings.
*Insulated
supply duct.
Nuaire
MVHR unit.
MVHR-DRAIN
Condensate drain, uninsulated
drain pipe with min 5 o fall running to SVP.
ALSO FROM NUAIRE New
range of thermal ducting,
an all-in-one insulated ducting system
(see installation document 671780)
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
16. 03. 21. Document Number 671863
6
MRXBOXAB-ECO4-AE(SC/SW)
Installation Manual
4.0 ELECTRICAL INSTALLATION
13 PCB Details
For good EMC engineering practice, any sensor cables or switched
live cables should not be placed within 50mm of other cables or on
the same metal cable tray as other cables.
EXTRA
F
EXTRA
CTCT
FAN
The electrical connection of the unit must be carried out by a qualified
electrician. The unit is supplied with a flexible cord for connection to
the mains supply.
Wiring is for reference purposes only, connections shown are factory
fitted. The unit is pre-wired with a 2 metre fly lead.
4.1 Electrical Information
FAIL
Voltage: 240V 1ph 50Hz
Consumption:
2.5A
This unit must be earthed.
The cable from the mains power supply should be connected to a fixed
wiring installation, via a fused isolator, in accordance with current IEE
wiring regulations.
Supply Extract Supply Extract Supply Extract
SPEED 1
SPEED 2
SPEED 3
4.2 Wiring Diagrams
Disconnection from the supply mains must be incorporated within
the fixed wiring in accordance with the wiring regulations and shall
have a minimum contact separation of 3mm.
4.2.1 Unit Only
14 Wiring Diagram - Unit Only
Green/yellow
MAINS
230V N
50Hz
L
Supply cord
from unit
Blue
Brown
5A Fuse
(BS1362)
2 Pole
Isolator
L
1
2
Black
Grey
3 Position Switch Ancillary code:
MRXBOX95-3SWITCH
4.2.2 Unit Serving One Bathroom
15 Wiring Diagram - One Bathroom
MAINS
230V N
50Hz
L
Green/yellow
Blue
Brown
5A Fuse
(BS1362)
Room
light
Light Switch
(Double Pole)
Black
3 Pole
Isolator
L
1
2
Grey
3 Position Switch Ancillary code:
MRXBOX95-3SWITCH
4.2.3 Unit Serving Two Bathrooms
16 Wiring Diagram - Two Bathrooms
MAINS
230V N
50Hz
L
Supply cord
from unit
Green/yellow
Supply cord
from unit
Blue
Brown
5A Fuse
(BS1362)
Room
lights
Black
3 Pole
Isolator
L
1
2
Grey
3 Position Switch Ancillary code:
MRXBOX95-3SWITCH
Light Switches
(Double Pole)
4.2.4 Summer / Winter Switch
17 Wiring Diagram - Summer / Winter Switch
2 core cable
from unit
Red
Black
Volt free Summer / Winter Switch (supplied with unit)
Polarity is inconsequential
Warning! - Do not connect to mains!
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
16. 03. 21. Document Number 671863
7
MRXBOXAB-ECO4-AE(SC/SW)
Installation Manual
5.0 COMMISSIONING
6.2 Status Indication
The filters fitted inside the unit are protected with a plastic film.
Prior to commissioning remove the covers (Figure 20), take off the
film and replace.
The status of the unit is indicated by a series of LED’s on the front cover.
The variants are listed below.
1. For the required air flow rates please refer to the design specification
for the property, follow Section 3.8, or refer to building regulations
ADF 2010.
2. The unit should be run for a minimum of 10 minutes to reach steady
state before commencing commissioning.
3. The humidity sensor is initially set to its least sensitive position, this
should be adjusted during commissioning. Depending on storage
and site conditions, the unit may boost due to high relative humidity
levels, this will continue until the level drops below the specified set
point.
4. The unit is supplied with independent control for both normal and
boost airflows (Figure 18).
5. Correct commissioning is essential to ensure the ventilation air flow
rates are met. It also ensures the unit is not over ventilating and
causing excessive power consumption.
6. Commissioning should be carried out in accordance with building
regulations document “Domestic ventilation compliance guide”.
www.planningportal.gov.uk/building regulations/approved
documents/partf/associated. A calibrated moving vane
anemometer and hood will be required to carry out commissioning.
7. Adjustment valves should be locked in place to prevent further
adjustment.
8. Once commissioned the home owner / tenant should be informed
that the unit should not be adjusted as it will have a detrimental
effect on the indoor air quality and could result in condensation and
mould growth. The clear panel covering the control has an adhesive
panel which should be exposed and sealed post commissioning to
prevent tampering.
18 Unit Control On Front Panel
The display on the unit control panel will not indicate when a
higher speed setting has been triggered by an external source, such
as an ES-PIR2 etc.
19 Unit Control On Front Panel (Standard Configuration Only)
Speed 1
Speed 2
Speed 3
Supply Fan Fault
Extract Fan Fault
Frost Protection
Filter Change
HX Bypass
(AB units only)
6.3 Integral Automatic HX Bypass
Intake and extract temperatures are monitored at the point the
airflows enter the unit, if the range falls within the set parameters the
bypass damper is opened automatically to target an indoor comfort
temperature all year round.
The extract temperature is an average from all wet rooms. If this
exceeds 25°C the unit may go into bypass depending on outside
temperatures.
6.4 Summer / Winter Switch
When the switch position is set to Summer the integral automatic
summer bypass is fully operational, in the alternative Winter position
the HX bypass is disabled to ensure the unit is constantly in heat
recovery mode.
6.5 Speed 3 Operation (SW Units Only)
Speed 3 will be non-operational if the intake temperature is greater
than the extract temperature.
Humidistat adjustment
(access by removing front cover)
Post commissioning remove
adhesive backing and seal
Ventilation Controls
Speed 1
+
-
+
Speed 2
-
+
-
+
Speed 3
-
+
-
+
In the event of the intake air temperature at the unit dropping below
the predetermined set point (-5°C as standard) the supply fan will
reduce to minimum speed, once the temperature rises above the set
point the fan will return to its commissioned speed.
Frost protection will only activate after ten days of continuous run
time. If commissioning of the unit is outside of this time frame please
notify the after sales department prior to site visit.
-
Supply Extract Supply Extract Supply Extract
6.6 Frost Protection
Power Fan
Failure
061021
6.0 CONTROLS
6.1 Humidity Adjustment
This product contains an internal humidity sensor fitted into the airflow extracting from the wet rooms. When the unit senses that the
humidity exceeds the set point, the unit will boost to that set by the
commissioned boost speed. The set point can be found on the front
of the unit (Figure 18) and is at its least sensitive when turned fully
clockwise. Note that the sensor is measuring humidity from all the wet
rooms at the same time and should not be relied on to solely boost the
unit.
Additional switch should be used local to the wet rooms (Section 4.2).
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
16. 03. 21. Document Number 671863
8
MRXBOXAB-ECO4-AE(SC/SW)
Installation Manual
7.0 MAINTENANCE
9.0 END-OF-LIFE AND RECYCLING
It is important that maintenance checks are recorded and that the
schedule is always adhered to, in all cases, the previous report should
be referred to.
Where possible Nuaire use components which can be largely recycled
when the product reaches its end-of-life:
Before commencing work make sure that the unit, switched live
and Nuaire control are electrically isolated from the mains supply
and switched live supply.
7.1 Filters
Filters are to be inspected every 6 months and replaced every 12
months (or sooner if required). Failure to do so may impair the
performance and energy efficiency of this unit. A flashing LED
(Section 6.2) will indicate that a filter change is required. This indication
repeats every 12 months and will turn off automatically after 5 Days.
Remove the filter covers on the front panel of the unit by gripping the
two circular tabs either end of the filter covers and pulling away from
the unit. The filter can now be extracted by pulling the black removal
loop on the front edge of the filter. Once the filters have been inspected
return or replace them as necessary.
20 Removing Filter Covers
Heat Exchanger
MVHR unit cover
•Fans, motors, controls, actuators, cabling and other electrical
components can be segregated into WEEE recycling streams.
•Sheet metal parts, aluminium extrusion, heating/cooling coils and
other metallic items can be segregated and fully recycled.
•EPP, plastic ducting, nylon corner pieces, plastic heat exchangers,
packaging material and other plastic components can be
segregated into mixed plastic and widely recycled.
•Cardboard packaging, wood, and other paper components can be
largely recycled or fully processed in energy from waste centres.
•Filter Disposal: Cardboard framed filters should be fully processed
in energy from waste centres, contact your local civic amenity site
/ household waste recycling centre regarding metal / wire framed
filters.
•Remaining Items can be further segregated and processed in
accordance with the zero waste hierarchy. Please call After Sales
Support for further information on items not listed above.
Ensure that Nuaire product is made safe from any electrical / water
/ refrigerant supplies before dismantling commences. This work
should only be undertaken by a qualified person in accordance with
local authority regulations and guidelines, taking into account all
site based risks.
10.0 AFTER SALES AND REPLACEMENT PARTS
For technical assistance or further product information, including spare
parts and replacement components, please contact the After Sales
Department.
Filter
Filter cover
Outer enclosure cover
8.0 WARRANTY
If ordering spares please quote the serial number of the unit together
with the part number, if the part number is not known please give a full
description of the part required. The serial number will be found on the
identification plate attached to the unit casing.
Telephone 02920 858 400
[email protected]
Technical or commercial considerations may, from time to time,
make it necessary to alter the design, performance and dimensions
of equipment and the right is reserved to make such changes without
prior notice.
The 5 year warranty starts from the day of delivery and includes parts
and labour for the first year. The remaining period covers replacement
parts only.
This warranty is void if the equipment is modified without
authorisation, is incorrectly applied, misused, disassembled, or not
installed, commissioned and maintained in accordance with the details
contained in this manual and general good practice.
The product warranty applies to the UK mainland and in accordance
with Clause 14 of our Conditions of Sale. Customers purchasing from
outside of the UK should contact Nuaire International Sales office for
further details.
Failure to maintain the unit as recommended will invalidate the
warranty.
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
16. 03. 21. Document Number 671863
9
Installation Manual
MRXBOXAB-ECO4-AE(SC/SW)
NOTES
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
16. 03. 21. Document Number 671863
10
Installation Manual
MRXBOXAB-ECO4-AE(SC/SW)
NOTES
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
16. 03. 21. Document Number 671863
11
Installation Manual
MRXBOXAB-ECO4-AE(SC/SW)
NOTES
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
16. 03. 21. Document Number 671863
12
">