Carrier Thermostat Operating instructions

Carrier Thermostat Operating instructions
33CS
Commercial Programmable Thermostat
Installation, Start-Up, and
Operating Instructions
Part Number 33CS220-01
CONTENTS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . 1
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Select Thermostat Location . . . . . . . . . . . . . . . . . . . 1
Install Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Set Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Heat Pump Configuration . . . . . . . . . . . . . . . . . . . . . 3
Configure Advanced Setup . . . . . . . . . . . . . . . . . . . 3
Install Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Program Thermostat Schedules . . . . . . . . . . . . . . . 4
Calibrate Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Check Thermostat Operation . . . . . . . . . . . . . . . . . 6
Final Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Autochangeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Two-Stage Operation . . . . . . . . . . . . . . . . . . . . . . . . . 7
Clock Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Emergency Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electric Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Holiday Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Keypad Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . 8
IMPORTANT: Read entire instructions before starting the installation.
SAFETY CONSIDERATIONS
Read and follow manufacturer instructions carefully. Follow all local electrical codes during installation. All wiring
must conform to local and national electrical codes. Improper wiring or installation may damage thermostat.
Recognize safety information. This is the safety alert sym. When the safety alert symbol is present on equipbol
ment or in the instruction manual, be alert to the potential
for personal injury.
Understand the signal words DANGER, WARNING, and
CAUTION. These words are used with the safety alert symbol. DANGER identifies the most serious hazards which will
result in severe personal injury or death. WARNING signifies a hazard which could result in personal injury or death.
CAUTION is used to identify unsafe practices which would
result in minor personal injury or property damage.
GENERAL
The 7-day, commercial, programmable thermostats are wallmounted, low-voltage thermostats which maintain room temperature by controlling the operation of an HVAC (heating,
cooling and ventilation) system. Separate heating and cooling set points and auto-changeover capability allow occupied and unoccupied programming for energy savings.
All thermostats allow up to 4 time/temperature settings to
be programmed per 24-hour period. Each thermostat stores
programs for 7 independent days. Batteries are not required.
During power interruption the internal NEVERLOST™
memory stores programmed schedules for an unlimited time
while the clock continues to run for at least 48 hours.
The thermostat can be configured to accept several different equipment configurations, including heat pump
operation.
NOTE: The thermostat is not factory-configured for use in
heat pump applications. The advanced setup must be performed to configure the thermostat for use with heat pump
units.
INSTALLATION
Select Thermostat Location — The thermostat should
be mounted:
• approximately 5 ft from the floor
• close to or in a frequently used room, preferably on an
inside partitioning wall
• on a section of wall without pipes or ductwork
• where temperature operating limits are within 41 to 104 F
(5 to 40 C)
• where humidity operating range is within 0 to 95% relative humidity, non-condensing
The thermostat should NOT be mounted:
• close to a window, on an outside wall, or next to a door
leading to the outside
• where exposed to direct light and heat from a lamp, the
sun, a fireplace, or any other temperature-radiating object
which may cause a false reading
• close to or in direct airflow from supply registers or return
air grilles
• in areas with poor air circulation (such as behind a door or
in an alcove)
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Book 1 4
PC 111
Catalog No. 533-321
Printed in U.S.A.
Form 33CS-15SI
Pg 1
1-98
Replaces: New
Tab 11a 13a
7. Secure mounting base to wall with 2 screws and anchors provided. Ensure all wires exit through hole in mounting base.
8. Adjust wire length and routing to allow proper closure
of the thermostat. Strip each wire at the end no more
than 1⁄4-in. to prevent adjacent wires from shorting together. Match and connect wires to terminals on the thermostat. See Fig. 2-4 and Table 1.
Install Thermostat
Before installing thermostat, turn off all power to the
unit. There may be more than one power disconnect.
Electrical shock can cause injury or death.
1. Turn off all power to unit.
2. If an existing thermostat is being replaced:
a. Remove existing thermostat from the wall.
b. Disconnect wires from existing thermostat. Do not
allow wires to fall back into the wall. As each wire
is disconnected, record wire color and terminal
connection.
c. Discard or recycle old thermostat.
NOTE: Mercury is a hazardous waste and must be
disposed of properly.
3. Remove the thermostat cover from wall plate (mounting base) to expose mounting holes. See Fig. 1. With the
thermostat facing forward, press the back plate on the
left hand side top corner to release the two prongs holding on the cover. Pull off the cover when the prongs have
been disengaged.
4. Route thermostat wires through large hole in mounting
base. Remove outer sheath from wires for added flexibility. Standard solid or multi-conductor thermostat wire
should be used from the thermostat to the unit. Size and
length considerations are as follows: for a maximum
distance from unit of 36 ft, use 22 AWG (American
Wire Gage) wire; for a maximum distance from unit
of 100 ft, use 18 AWG wire.
5. Level mounting base against wall and mark wall through
the 2 mounting holes in base.
6. Drill two 3⁄16-in. mounting holes in wall where marked.
Improper wiring or installation may cause damage
to the thermostat. Check to ensure wiring is correct before proceeding with installation of unit.
9. Push excess wiring into wall. Seal hole in wall to prevent drafts.
10. Re-attach thermostat cover to back plate by aligning the
top two prongs of the back plate in the vertical groove
of the top cover and then snapping the cover onto the
back plate.
11. Turn on power to unit. The thermostat will receive power
from the unit. The thermostat will be powered by 24 v,
nominal (18 to 30 vac). Terminals R (+ 24 v), W1/O/B
(first stage heat or reversing valve), Y1 (first stage cooling), and G (fan relay) will always be connected. Some
applications will use C (common), Y2 (second stage cooling), or W2 (second stage heating).
Be careful not to drill into wiring in wall. Electrical shock could result.
LEGEND
W2
Y2
— Second-Stage Heat
— Second-Stage
Compressor
RS2
— Not Used
RS+5
— Not Used
RS1
— Not Used
RS GND — Not Used
W1/O/B
— First-Stage Heat or
Reversing Valve
Y1
— First-Stage Compressor
G
— Fan
W3/ECO — Third-Stage Heat or
Economizer (Not Used)
CK1
— Not Used
CK2
— Not Used
R
— 24 vac Transformer
C
— 24 vac Transformer
Common
Fig. 2 — Thermostat Wiring
Fig. 1 — Thermostat Mounting
2
THERMOSTAT
B
O
W2 Y2 R W1 Y1 G
Heat Pump Configuration — To configure the thermostat for heat pump operation, Advanced Setup Steps 3 (Heat
Pump Operation) and 4 (Reversing Valve Polarity) must be
configured correctly. See the Configure Advanced Setup section for information on configuring these options.
NOTE: Some large commercial rooftop heat pump units
(50HJQ,TJQ,EJQ) must be configured with Advanced Setup
Step 3 (Heat Pump Operation) set to OFF. Refer to the base
unit instructions for more information.
TYPICAL
UNIT
C
L
E
24 VAC COMMON
C
FAN RELAY
G
COMPRESSOR RELAY
Y1
O
1st STAGE HEAT CIRCUIT
Configure Advanced Setup — To enter into the advanced setup screens of the thermostat, press the Mode and
Program buttons at the same time. The Advanced Setup Step
number is shown in the top right corner of the thermostat
screen. Use the Mode button to advance through the steps.
There are 15 Advanced Setup Steps. See Table 2. Press the
Program button at any time to exit the Advanced Setup mode.
NOTE: Advanced Setup Steps 1 and 2 are configured with
the Set Clock button, and are not accessed through the advanced setup screens.
HEAT PUMP CONFIGURATION (Steps 3 and 4) — To set
the thermostat for heat pump operation, Advanced Setup
Step 3 must be configured to ON. Use the UP and DOWN
ARROW buttons to configure the step. The default is OFF.
Press the mode button to continue to Step 4. Step 4 is used
to set the reversing valve polarity for the heat pump. The
variable can be set to either ‘‘B’’or ‘‘O.’’ Set the reversing
valve polarity to the correct value depending on the application. The default is ‘‘O.’’
NOTE: Step 4 will appear only if Step 3 is set to ON.
Step 5 will appear only if Step 3 is set to OFF.
ELECTRIC HEAT CONFIGURATION (Step 5) — Step 5
is used to configure the thermostat for electric heat. The variable can be configured ON or OFF. The default is OFF.
NOTE: Step 5 will appear only if Step 3 is set to OFF.
W1
24 VAC RETURN
R
Y2
2nd STAGE HEAT CIRCUIT
W2
Fig. 3 — Typical Wiring (Single-Stage Cooling Units)
THERMOSTAT
B
O
W2 Y2 R W1 Y1 G
TYPICAL
UNIT
C
L
E
24 VAC COMMON
FAN RELAY
COMPRESSOR RELAY
C
G
Y1
O
1st STAGE HEAT CIRCUIT
24 VAC RETURN
2nd STAGE COMPRESSOR RELAY
2nd STAGE HEAT CIRCUIT
W1
R
Y2
W2
Fig. 4 — Typical Wiring (Two-Stage Cooling Units)
Table 1 — Thermostat Wiring Terminations
EXISTING
WIRE
DESIGNATION
G or F
Y1, Y, or C
W1, W, or H
Rh, R, M, Vr, or A
C
O/B
Y2
W2
Table 2 — Advanced Setup Configuration
FUNCTION
TERMINAL
CONNECTION
Fan
Cooling
Heating
Power (24 v)
Common
Reversing Valve
Second Stage Cooling
Second Stage Heating
G
Y1
W1/O/B
R
C*
W1/O/B†
Y2*
W2*
STEP
1*
Time of Day
2*
Day of the Week
3
4
5
6
*Terminals C, W2, and Y2 may not be used in all applications.
†Used on Heat Pump applications only.
7
8
9
Set Clock — The Set Clock button allows the user to change
the time and day displayed on the thermostat. Press the Set
Clock button. The current time will blink on and off. Press
the UP ARROW and DOWN ARROW buttons until the correct time is shown. Hold down the buttons to quickly move
through the time display. The AM and PM annunciators will
automatically change. Hold down the Fan button while pressing UP ARROW or DOWN ARROW to change the time by
hours instead of minutes. To ensure the schedules are properly followed, make sure that AM or PM is correct for the
time chosen. When the correct time is shown, press the Mode
button to modify the day of the week. The current day will
blink on and off. Press the UP ARROW and DOWN ARROW buttons until the correct day is shown. Press the Set
Clock button again to exit the Set Time mode.
DESCRIPTION
10
11
12
13
14
15
RANGE
12:00 AM 11:59 PM
Sunday through
Saturday
Off/On
DEFAULT
12:00 AM
Monday
Heat Pump
Off
Reversing Valve
O/B
O
Polarity
Electric Heat
Off/On
Off
Deadband
1 - 6 degrees
2
Forced Minimum
0 - 6 degrees
2
Temperature Difference
Cycles per Hour
d, d1, 2 - 6
6
Thermoglow™ Backlight
Off/On
On
Reset Service
—
—
Filter Icon
Service Filter
0-1950 hrs
500 hrs
Run Time
Temperature Units
F/C
F
Security Level
0-3
0
Maximum Allowable
35 - 99 F (1-37 C) 80 F (27 C)
Heat Set Point
Minimum Allowable
35 - 99 F (1-37 C) 65 F (18 C)
Cooling Set Point
*Accessed and configured through the Set Clock button.
3
Refer to the accessory installation instructions for the accessory for more information.
DEADBAND (Step 6) — The deadband is the difference in
temperature above the cooling set point or below the heating
set point that the thermostat will wait before turning on the
first stage of heating or cooling. For example, if the cooling
set point is 82 F (28 C) and the deadband is 2 degrees, the
first stage of cooling will not be energized until the temperature reaches 84 F (30 C). The range of values is 1 to 6 degrees. The default is 2 degrees.
SET POINT MINIMUM DIFFERENCE (Step 7) —The minimum difference between heating and cooling set points can
be user-configured. The range is from 0 to 6 degrees. The
default is 2 degrees. The minimum difference is enforced
during Autochangeover and Program On operation.
CYCLES PER HOUR LIMIT (Step 8) — The number of
times that heating or cooling can be energized per hour can
be configured. Set the variable to ‘‘d’’ for no limit. Set the
variable to ‘‘d1’’ to disable the 5-minute compressor lockout. The variable can also be set from 2 to 6 cycles per hour.
The default is 6 cycles per hour.
Program Thermostat Schedules — Before programming the thermostat, plan the thermostat daily schedule. The schedule is divided into 7 days (Monday through
Sunday). Each day has from 2 to 4 time periods (Occupied
1, Occupied 2, Occupied 3, Unoccupied) depending on the
configuration of the thermostat. Each occupied time period
has a start time, stop time, heating set point, and cooling set
point. The unoccupied time period has a heating set point
and a cooling set point. The unoccupied time period is active
when ever an occupied time period is not active. Fill in
Table 3 as an aid to programming the daily schedules.
PROGRAMMING MODE — To program the daily schedules, perform the following procedure:
1. Enter programming mode by pressing the Program button. The Occupied 1 annunciator will appear on the thermostat display. Use the UP ARROW and DOWN ARROW buttons to set the maximum number of Occupied
periods for each day. The thermostat can be set to 1, 2,
or 3. After the number of Occupied periods has been
selected, press the Mode button. See Fig. 5.
2. The cooling set point for Occupied 1 will be displayed.
Use the UP ARROW and DOWN ARROW buttons to
raise or lower the cooling set point until the desired temperature is shown. The range of acceptable values is 35
to 99 F (1 to 37 C). Press the Mode button to continue.
See Fig. 5.
3. The heating set point for Occupied 1 will be displayed.
Use the UP ARROW and DOWN ARROW buttons to
raise or lower the heating set point until the desired temperature is shown. The range of acceptable values is 35
to 99 F (1 to 37 C). Press the Mode button to continue.
See Fig. 5.
Damage to compressor could result if 5-minute compressor lockout is disabled or compressor is allowed unlimited cycles. Do not set thermostat Advanced Setup
Step 8 to ‘‘d’’ or ‘‘dl’’ unless specifically recommended for the application.
BACKLIGHT DISPLAY (Step 9) — The display backlight
can be set to ON (always on) or OFF (turn off 8 seconds
after usage). The default is ON.
SERVICE FILTER (Steps 10 and 11) — Step 10 allows the
user to reset the Service Filter counter to zero and remove
the ‘‘SERVICE FILTER’’ icon (if displayed on the thermostat screen). Press the FAN button while in Setup Step 10
and the counter is reset to zero. Press the Mode button to
adjust the number of hours the blower will run before the
‘‘SERVICE FILTER’’ icon is displayed. The range is 0 to
1950 hours. Set the variable to 0 to disable this function.
The default is 500 hours.
FAHRENHEIT/CELSIUS OPERATION (Step 12) — The
thermostat can be set to operate in Fahrenheit or Celsius degrees. Set the variable to ‘‘F’’ for Fahrenheit operation. Set
the variable to ‘‘C’’ for Celsius operation. The default is ‘‘F.’’
SECURITY LEVEL (Steps 13 to 15) — The Security Level
limits the actions that the user can perform at the thermostat.
There are 4 security levels. When the security level is set to
‘‘0,’’ no security will be in effect. When the security level is
set to ‘‘1,’’ the set point range is limited by the settings of
Steps 14 and 15. When the security level is set to ‘‘2,’’ the
set point range is limited by the settings of Steps 14 and 15
and the Program On mode is always in effect. When the security level is set to ‘‘3,’’ the set point range is limited by the
settings of Steps 14 and 15, the Program On mode is always
in effect, and set point changes are prohibited. The default
is 0.
Security Maximum Heat Set Point (Step 14) — If the Security Level is not set to 0, the maximum heating set point
will be in effect. The user will not be allowed to set the heating set point over the specified value. The range of values is
35 to 99 F (1 to 37 C). The default is 80 F (27 C).
Security Minimum Cool Set Point (Step 15) — If the Security Level is not set to 0, the minimum cooling set point
will be in effect. The user will not be allowed to set the cooling set point below the specified value. The range of values
is 35 to 99 F (1 to 37 C). The default is 65 F (18 C).
Fig. 5 — Setting Occupied 1 Set Points
4. The cooling set point for Unoccupied will be displayed.
Use the UP ARROW and DOWN ARROW buttons to
raise or lower the cooling set point until the desired temperature is shown. The range of acceptable values is 35
to 99 F (1 to 37 C) or ‘‘OF’’ (no unoccupied cooling).
Press the Mode button to continue.
5. The heating set point for Unoccupied will be displayed.
Use the UP ARROW and DOWN ARROW buttons to
raise or lower the heating set point until the desired temperature is shown. The range of acceptable values is 35
to 99 F (1 to 37 C) or ‘‘OF’’ (no unoccupied heating).
Press the Mode button to continue.
6. The day of the week will be shown. Use the UP ARROW and DOWN ARROW buttons to change the day
of the week until the desired starting day is shown. Possible choices are M (Monday) through S (Sunday). Press
the Mode button when the desired day is shown.
Install Accessories — The following accessory
can be used with this thermostat: Add-a-Wire™ accessory
(33CSACC-AW).
4
Table 3 — Daily Schedule Planner
SCHEDULE
DAY
OF THE
WEEK
Occupied 1
Occupied 2
Occupied 3
Unoccupied
Start / Stop / Heat / Cool
Start / Stop / Heat / Cool
Start / Stop / Heat / Cool
Heat / Cool
Monday
/
/
/
/
/
/
/
/
/
/
Tuesday
/
/
/
/
/
/
/
/
/
/
Wednesday
/
/
/
/
/
/
/
/
/
/
Thursday
/
/
/
/
/
/
/
/
/
/
Friday
/
/
/
/
/
/
/
/
/
/
Saturday
/
/
/
/
/
/
/
/
/
/
Sunday
/
/
/
/
/
/
/
/
/
/
NOTE: The cooling temperature set point must be higher than the heating temperature set point. (The temperature difference may be changed in
the advanced setup configuration.)
5
7. The Start Time for Occupied 1 will be displayed. Use
the UP ARROW and DOWN ARROW buttons to raise
or lower the time until the desired Start Time is shown.
Press the Mode button to continue. See Fig. 6.
If only one occupied schedule is selected, the Occupied 2
and 3 schedules are skipped. If the start time is set later in
the day than the stop time, the program will run from midnight of that day to the stop time and then from the start time
to midnight. If the same start and stop times are programmed for an occupancy schedule, the thermostat will be
in Occupied mode for 24 hours. If one occupied period starts
or stops within another occupied period, the lower numbered schedule has priority. For example, if schedule Occupied 3 is running for 24 hours and Occupied 2 schedule
comes on from 1 to 3 PM, the set points from Occupied 2
are in effect from 1 to 3 PM.
OVERRIDING THE SCHEDULE — The schedule can be
overridden by pressing the UP or DOWN ARROW buttons
to change the desired temperature. The thermostat will use
the new set point until the next scheduled time period starts.
Fig. 6 — Start Time Display
Calibrate Sensor — Every thermostat is factory calibrated. Under normal circumstances there will never be a
need to re-calibrate the thermostat. If re-calibration must be
done, perform the following procedure:
1. Hold down the Mode and Fan buttons for 5 seconds. All
of the icons on the display screen will appear. Release the
buttons. Press the UP and DOWN ARROW buttons
simultaneously.
2. Press the UP and DOWN ARROW buttons simultaneously again. The current temperature will be
displayed.
3. Use an accurate thermometer to measure room temperature. Press the UP or DOWN ARROW buttons until the
number equals room temperature.
4. Press the Mode button to return to normal operation.
8. The Stop Time for Occupied 1 will be displayed. Use
the UP ARROW and DOWN ARROW buttons to raise
or lower the time until the desired Stop Time is shown.
Press the Mode button to continue.
9. The On/Off icon will be displayed. Use the UP ARROW to turn the Occupied 1 period ON for this day.
Use the DOWN ARROW to turn the Occupied 1 period
OFF for this day.
10. Repeat Steps 2 through 9 to program the remaining schedule for Occupied periods 2 and 3.
11. The Copy command can be used to copy the previous
day’s schedule if the schedules are the same. The copy
command becomes available after all the occupied periods are programmed in a day. Use the UP ARROW to
change the copy command to YES. Use the DOWN ARROW to change the copy command to NO. Press the
Mode button when the choice has been made. See
Fig. 7.
If NO was selected, the schedule will automatically change
to the next day and the user must enter the occupied and
unoccupied schedules for that day.
NOTE: Occupied 1 schedule heating and cooling set points
are the same for each day. Occupied 2 and 3 set points
may be set to different values for each day of the week.
If YES was selected, the schedule will be copied to the
next day. The schedule copy may be repeated until Sunday is reached. The Sunday schedule cannot be copied
to Monday.
12. After all the times and set points for each day have been
entered, press the Program button to exit programming
mode.
NOTE: The thermostat will continue to follow the schedule
until a new one is entered.
Check Thermostat Operation — To check thermostat operation, perform the following procedure:
1. Press the Mode button repeatedly until the Heat icon appears on the display. The thermostat is now in Heating
mode.
2. Press the Fan button. The Fan Auto icon will appear on
the display screen. Press the UP ARROW button until the
heating set point is 10 F (6 C) higher than the current
room temperature. Heating and fan should be
energized.
3. Press the Mode button repeatedly until the Cool icon appears on the display. The thermostat is now in Cooling
mode.
4. Press the DOWN ARROW button until the cooling set
point is 10 F lower than the current room temperature.
Cooling and fan should be energized.
5. Press the Mode button repeatedly until the Off icon appears. Press the Fan button until the display reads Fan
On. The fan should energize.
6. If heating, cooling, or fan operation do not work, check
wiring and consult Table 4.
Final Checklist
1. Put away tools and instruments. Clean up debris and
packaging.
2. Review Owner’s Guide with occupant or owner.
3. Leave the manuals with owner.
Fig. 7 — Copy Command Display
6
of heat will be energized (locking out the first stage compressor). To exit emergency heat, press and hold the Fan button. While holding the Fan button, press the UP button for
2 seconds. During emergency heat, only OFF and HEAT modes
are available.
OPERATION
The Mode button selects the operating mode of the thermostat. If OFF is selected, the thermostat will not enter Heating or Cooling mode. If HEAT is selected, the thermostat
will only enter Heating mode (if the room temperature is
below the heating set point). If COOL is selected, the thermostat will only enter Cooling mode (if the room temperature is above the cooling set point). If AUTO is selected, the
thermostat will enter Heating or Cooling mode based on the
room temperature and the heating and cooling set points. If
PROGRAM ON is selected, the stored schedule is enabled
and the thermostat will follow the Occupied and Unoccupied schedules stored in its memory.
Electric Heat — When the Electric Heat option in the
advanced set up is set to ON (configured by installer), the
thermostat will turn on the fan immediately any time there
is a heat demand. This feature should only be used on electric heating applications. Do not use with gas heat.
Holiday Mode — When the thermostat is in Holiday mode,
the thermostat will operate under Unoccupied set points. To
configure and activate the Holiday mode, press the Holiday
button. The ‘‘HOL’’ icon will be displayed along with the
remaining days of Holiday mode operation. Press the UP or
DOWN ARROWS to select the number of days that the holiday schedule will be in effect. A value of 0 disables Holiday
mode. The duration can be set from 1 to 99 days. The thermostat will enter Holiday mode on midnight of the next day
after the mode has been activated. Holiday mode will remain in effect until midnight of the last configured day.
If the Holiday mode is in effect, the number of days remaining will blink on and off and the ‘‘Unoccupied’’ icon
will be displayed. The Override button will be active during
Holiday mode.
To turn off the Holiday mode before the remaining configured days have passed, press the Holiday button to enter
into the configuration mode. Press the DOWN ARROW to
set the number of days to zero. Holiday mode will be
disabled.
Auto-Changeover — When the thermostat mode is set
to AUTO, the thermostat will provide automatic changeover
from Heating to Cooling mode and Cooling to Heating mode
when required. The thermostat will automatically switch to
maintain the desired temperature setting. The thermostat does
not need to be manually changed from heating to cooling or
cooling to heating operation.
Two-Stage Operation — The second stage of heat or
cool is turned on when the first stage has been on for a minimum of 2 minutes and the temperature differential from the
set point is equal to or greater than the set point plus the
deadband plus 2 degrees.
Clock Backup — In the event of a power loss, the thermostat will keep time for a minimum of 48 hours without
external power or batteries.
Fan Operation — If Fan On is selected, the fan will run
continuously during occupied schedule (except when Mode
is switched to OFF). The fan will be off during unoccupied
schedule except during heating or cooling operation.
If Fan On is not selected, the fan will only operate during
heating or cooling operation.
Keypad Lock — To prevent unauthorized use of the thermostat, the front panel buttons can be disabled. To disable or
lock the keypad, press and hold the Mode button. While holding down the Mode button, press the UP and DOWN ARROW buttons simultaneously. The ‘‘Locked’’ icon will appear on the display.
The thermostat is unlocked by performing the same procedure. Press and hold the Mode button. While holding down
the Mode button, press the UP and DOWN ARROW buttons
simultaneously. The ‘‘Locked’’ icon will be removed from
the display.
Emergency Heat — Emergency heat is available for heat
pump applications. To turn on emergency heat, press and hold
the Fan button. While holding the Fan button, press the UP
button for 2 seconds. An ‘‘EH’’ will be displayed. During
emergency heat, the fan will operate and the second stage
7
TROUBLESHOOTING
Table 4 — Thermostat Troubleshooting
PROBLEM
Display on thermostat not illuminated.
‘‘Service Filter’’ is displayed on thermostat.
Cooling will not energize.
Heating will not energize.
When using 4 wires (R,G,W,Y), the cooling equipment tries repeatedly to turn on, but cannot. At
times the display dims or disappears.
When using 4 wires (R,G,W,Y), the heating equipment tries repeatedly to turn on, but cannot. At
times the display dims or disappears.
When controlling a heat pump, heat comes on
during cooling cycle.
When calling for cooling,
both heating and cooling are energized.
When controlling a commercial heat pump unit,
unit runs in reverse or heating is always on.
SOLUTION
Check for 24 vac at the R terminal connection. Terminal R must be
connected for proper thermostat operation.
After the configured number of blower operating hours, the Service
Filter message will be displayed. This reminds the owner to replace
the filter. Reset the Service Filter feature to reset the blower operation timer to 0 hours.
Select COOL mode. Decrease cooling set point to 10 degrees below room temperature. Check for 24 vac at Y1 terminal. If present,
thermostat is operating correctly and problem is with wiring or equipment. If 24 vac is not present, replace the thermostat. Check for
Compressor Cycle per Hour Limit. Cooling may be locked out.
Select HEAT mode. Increase heating set point to 10 degrees above
room temperature. Check for 24 vac at W1/O/B terminal. If present,
thermostat is operating correctly and problem is with wiring or equipment. If 24 vac is not present, replace the thermostat.
There is not enough power available. Connect a 270 ohm, 10 watt
power resistor at the air-conditioning equipment between terminals
W and C (non-heat pump applications only).
There is not enough power available. Connect a 270 ohm, 10 watt
power resistor at the air-conditioning equipment between terminals
Y and C (non-heat pump applications only).
Configure thermostat for heat pump operation (Table 2, Step 3).
The thermostat is configured for a heat pump. Configure the thermostat for non-heat pump operation (Table 2, Step 3).
Commercial heat pumps require that Heat Pump Option on thermostat is turned OFF.
Copyright 1998 Carrier Corporation
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Book 1 4
PC 111
Catalog No. 533-321
Printed in U.S.A.
Form 33CS-15SI
Pg 8
1-98
Replaces: New
Tab 11a 13a
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement