red lion Engine-Driven Aluminum TRANSFER Pump Technical data

red lion Engine-Driven Aluminum TRANSFER Pump Technical data
RED LION
CHEMICALS
®
• Adhesives and Sealants
• Bulk Chemicals
• Cleaners and Degreasers
• Skin Care
• Insecticides
• Lubricants
• Paints and Coatings
• Paint Removers
• Specialty Products
• Eco-Friendly Chemicals
• Odor Eliminators
• Dispensing Equipment
RED LION CHEMICAL FORMULATIONS PROVIDE THE ULTIMATE
IN PERFORMANCE WHILE MAINTAINING MAXIMUM SAFETY
FOR THE USER. Aerosols, bulk and specialty products that work better,
faster and safer.
®
CHROMATE INDUSTRIAL CORP.
EXCEPTIONAL PRODUCTS, SERVICE AND INNOVATIVE SOLUTIONS
30
30
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
Table Of Contents
Adhesives and Sealants ....................................... 30.1
Bulk Chemicals ..................................................... 30.25
Cleaners and Degreasers .................................. 30.39
Skin Care ................................................................. 30.52
Insecticides ............................................................ 30.60
Lubricants ............................................................... 30.63
Paints and Coatings ............................................ 30.81
Paint Removers ..................................................... 30.90
Specialty Products .............................................. 30.93
Eco-Friendly "Green" Chemicals .................... 30.97
Safe-T-Line™ Products ....................................... 30.101
Odor Eliminators ................................................. 30.103
Dispensing Equipment ...................................... 30.107
Bulk Chemical Dilution Chart ........................ 30.116
R134A Lubricant Reference Charts ............ 30.117
Can Puncturing System ................................... 30.122
Red Lion™ Chemical Selector ......................... 30.126
Red Lion™ Index .................................................. 30.128
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30
30
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
Adhesives and Sealants
Concrete Crack Repair
Part #74508 – 5 Gallon Pail (74g)
(Epoxy polymer repair for concrete)
A trowelable polymer composite for repairing cracked and spalled concrete. Outlasts ordinary concrete.
Provides four times the compression strength and ten times the tensile strength of standard concrete. It
is non-shrinking, non-cracking and may be feather edged or poured up to 5 inches thick. One 5-gallon
pail will surface approximately 15 square feet of floor at 1/4” thickness.
Features
• Easy-to-use, permanent concrete repair
• Trowelable polymer composite
• Non-shrinking and crack resistant
• 4 times stronger than original cement
• Can be Feathered or Poured up to 5" Thick
Applications
• Ideal for setting anchors
• Filling cracks, gaps, holes, etc.
Drop-Tite™ Epoxy System
Part #74534 – 21.2 oz
("Fast cure" formula for projects requiring "fast bolt-up")
A "fast cure" formula specially developed for projects requiring "fast bolt-up" and extended working time
in a variety of applications. The complete system comes with a 22-oz. two-part epoxy cartridge and two
3/8 mixing nozzles. Must be used with daul cartridge caulking gun, p/n 8250 (see Dispensing Equipment).
Features
• Superior Bond Strength – maintains its full bonding integrity under seismic and vibratory loads,
even in underwater applications.
• Exhibits no offensive odors which is especially important when work is performed in enclosed areas.
• Bonding Not Affected by Concrete Dust – wets through residual dust and adheres directly to concrete or steel.
• Corrosion Resistant – seals out oxygen and moisture that can cause corrosion.
• Minimal Shrinkage – when compared to other epoxies and formulas containing styrene.
• Non-Combustible – flash point is three times greater than that of formulas containing highly flammable styrenes.
• Non-Carcinogenic – contains no styrene and is safer for users.
• Longer Shelf Life – 2-3 times longer than products containing styrene.
P/N 8251 – Mixing Tube
Applications (For use with Drop-TiteTM Anchors)
• Horizontal, vertical and overhead anchoring and doweling
• Seismic repair and upgrade
• Concrete repair (non-structural)
• Bonding applications
• Use in concrete, hollow concrete block (CMU), solid and hollow brick and stone
30
CURE TIMES*
Gel......................... 8-10 Minutes
Loading...........................4 Hours
Full-Cure.......................48 Hours
Recommended
Temp. Range..........36oF-110oF
*Based on a temperature of 78oF (25oC).
Gel times are calculated on a mass of 20
grams. The recommended temperature
range refers to the maximum and minimum substrate temperatures in which the
product may be used.
030111
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.1
Adhesives and Sealants
Double/Bubble Epoxy Extra Fast
®
(Exta fast setting epoxy adhesive / 5 packets per box)
Part #74499 – 3.5 g
Strong and versatile. Does more to repair jobs in less time. Contains no solvents. Will not shrink.
Features:
• Work time: 3 minutes
• Handling strength: 15-30 minutes
• Fills gaps
• Does not induce galvanic corrosion
Applications:
• Bonds metal, glass, ceramics, wood, stone, concrete, most hard plastics, leather
• For repairing tools, auto parts, electronic components, furniture, etc.
Double/Bubble Machineable Epoxy
®
Part #74498 – 3.5 g
(Fast setting / 5 packets per box)
A machineable tooling and body patch that adheres to metal, wood and hard plastics.
Can be machined, sanded, drilled and tapped.
Features:
• Work time: 25 minutes‑
• Handling strength: 4 hours
• Aluminum color
• Contains no solvents
Applications:
• Patching and filling voids and scratches in plastic and metal tooling, patterns and furniture.
Double/Bubble General Purpose Epoxy
®
(A long work-life adhesive / 5 packets per box)
Features:
• Work time: 2 hours
• Handling strength: 8 hours
• Does not induce galvanic corrosion
Part #74497 – 3.5 g
Applications:
• For bonding wood, metal, ceramics, concrete, rubber & plastics
• Repair of tools, furniture and sports equipment. An excellent adhesive for use
with fiberglass cloth.
30
Double/Bubble High Peel Strength Epoxy
®
(Flexible, tough and durable / 5 packets per box)
Features:
• Work time: 3 hours
• Handling strength: 18 hours
• Vibration resistant adhesive
• High peel and shear strengths
30.2
Part #74496 – 3.5 g
Applications:
• Bonds to polystyrene, ABS nylon, metal, wood, masonry and rubber
• For repair of sports equipment, marine, aircraft, auto, truck and tractor parts.
Excellent adhesive for grinding wheel hubs, door and window gaskets.
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
030111
070112
Adhesives and Sealants
Double/Bubble Wet Surface Patch Epoxy
®
(A gap filling adhesive / 5 packets per box)
Part #74495 – 3.5 g
For use in damp or moist environments. Cures and bonds under water. Bonds to stone, concrete, metal, glass, china, wood and fiberglass.
Features:
• Work time: 25 minutes
• Handling strength: 5 hours
• Gray color
Applications:
• Wet crack sealant and plumbing patch.
For repair of gutters, battery cases and
boats. Excellent adhesive for use with
fiberglass tape.
Double/Bubble Water Clear Epoxy
®
(Use as an adhesive or coating / 5 packets per box)
Part #74494 – 3.5 g
Covers and fills scratches. Impact resistant. Bonds to metal, ceramics, glass, porcelain and wood.
Features:
• Work time: 1 hour
• Handling strength: 8 hours
• No color – clear
• Does not electrically corrode copper
Applications:
• Repair of printed circuit boards,
optical fibers, lenses and other optical
equipment, jewelry, art objects and other
applications where a clear bond is desired.
Double/Bubble Regular Setting Epoxy
®
(Regular setting epoxy adhesive / 5 packets per box)
Part #74493 – 3.5 g
Strong and versatile. Does more to repair jobs in less time. Contains no solvents. Will not shrink.
Features:
• Work time: 45 minutes
• Handling strength: 4 hours
• A low-viscosity adhesive
• Fairly long work-life
• Cures to a light color
Applications:
• Bonds well to wood, metal, concrete, fabrics
and most plastics
• Excellent for applications requiring a thin
glue line. Ideal for fine furniture, hobby use
and sports equipment.
30
Double/Bubble Extra Fast Set (Non-Sag) Epoxy
®
Part #74492 – 3.5 g
(Extra-fast setting / 5 packets per box)
Strong and versatile. Does more to repair jobs in less time. Contains no solvents. Will not shrink.
Features:
• Work time: 3 minutes
• Handling strength: 15-30 minutes
• Non-sag (thixotropic) adhesive
• For quick repairs
030111
070112
Applications:
• Bonds to wood, glass, metal, stone,
ceramics and leather
• Ideal for quick, permanent, vertical and
overhead repairs. For fixturing, tacking,
sealing, gap filling and staking in electrical
and industrial applications.
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.3
Adhesives and Sealants
Double/Bubble Urethane – Flexible
®
(Shore Hardness D-50)
P/N 74417 – 3.5 g
• A good combination of high peel and lap shear strengths
• It is semi-flexible and will bond to rubber, leather, china and many plastics
Uses: For automotive repairs, bonding aftermarket replacement mirrors, etc.,
repair of shoes, ski boots and other sports equipment, repair of conveyor belts.
Work time: 3-5 minutes
Handling strength: 1 hour
Double/Bubble Urethane – Semi-Rigid
®
(Shore Hardness D-85)
P/N 74418 – 3.5 g
• Extra fast setting, semi-rigid
• Combines very high lap shear strength with good peel strength
Uses: For repair of urethane RIM parts. Recommended for repair of rubber hoses
and flexible electrical connections.
Work time: 3-5 minutes
Handling strength: 1 hour
Double/Bubble Urethane – Very Flexible
®
(Shore Hardness A-85)
P/N 74419 – 3.5 g
• Fast setting with high peel strength
• Tough and flexible
• Bonds to most metals, plastics, rubber, glass and leather
• Good for low temperature, sub-zero applications
• Patching and filling voids and scratches in plastic and metal tooling, patterns and furniture
30
Uses: Repair of construction and off-road tires, flexible conveyor belts, printing press rollers,
rubberized fabrics, shoes, ski boots and other sports equipment. For bonding refrigeration
and air-conditioning equipment.
Work time: 8 minutes
30.4
Handling strength: 45 minutes
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
030111
070113
Adhesives and Sealants
E-Z Poxy™ 200
Part #74502 – 4 oz.
(For steel hard repairs in a stick)
A combination of steel reinforced epoxy resin and hardener in a stick. Simply knead putty and apply to
damaged area. It can be drilled, filed, tapped, sanded or machined after one hour.
Features:
• No measuring, mess or waste
• Fast – sets in 10 minutes
• Adheres to damp surfaces and hardens under water
• Certified to NSF/ANSI Standard 61 for use in contact
with potable water and drinking water systems
• Authorized by the USDA for use in federally
inspected meat and poultry plants
PHYSICAL PROPERTIES:
Density.................... 18.5 lb./gal. (2.2 gm/cm3)
Compression Strength ....................12,000 psi
Tensile Strength ................................6,000 psi
Modulus of Elasticity .......................6 x 105 psi
Adhesive Strength ...............................900 psi
Izod Impact .................. 0.3 ft.-lb./in. (notched)
Hardness (Shore D).................................... 80
Maximum Use Temp .................300oF (149oC)
ELECTRICAL PROPERTIES:
Volume Resistance ............... 1 x 1012 ohm-cm
Dielectric Strength .... 300 volts/mil @ 0.15 cm
IMPORTANT: Do not use on polyethylene,
polypropylene and polybutylene.
Applications:
• Perfect for repairing tanks, radiators, bathroom fixtures,
tile, cars, boats, metal and wood furniture, downspouts,
gutters, garbage cans, valves, cast iron,etc.
E-Z Poxy™ Aluminum
Part #74505 – 4 oz.
(Strong, fast setting, fast curing, multi-purpose epoxy putty stick)
A hand-kneadable, non-rusting, aluminum reinforced
epoxy putty that mixes in just one minute to provide fast
repairs to all types of aluminum. It comes in a handy
four-ounce "tootsie roll" form with the curing agent
encapsulated in the contrasting color base material. The
putty-like consistency eliminates drips and runs, providing
"no mess" applications with no tools required for use.
Simply cut off amount needed, knead and apply.
PHYSICAL PROPERTIES:
Work Life (Minimum) ......................................5-7
Shelf Stability ............... 24 months (min. @ 75oF)
Shore D Hardness (full cure 24 hrs.) ..........75-85
Lap Shear Tensile Strength ...... 500-700 on steel
(1" x 1" x 1/16") .............. 400-600 on aluminum
Compression Strength lbs./in.2 ................ 12,000
Shrinkage .....................................................<1%
Non-Volatile Content...................................100%
Electrical Resistance ............... 30,000 megohms
Dielectric Strength ........................... 300 volts/mil
Temperature ............................ 250oF continuous
.................................................300oF intermittent
Chemical Resistance: Resistant to hydrocarbons,
ketones, alcohols, esters, halocarbons, aqueous
salt solutions and dilute acids and bases.
Features:
• No measuring, mess or waste
• Fast – cures in 60 minutes
• Non-rusting – can even be applied underwater
Applications:
• Perfect for repairing storm doors, windows, aluminum boats, recreational vehicles, aluminum
siding, aluminum tanks, castings, pipes and engine blocks.
E-Z Poxy™ Aqua Repair
Part #74500 – 4 oz.
(Repairs wet areas and underwater surfaces)
A hand-kneadable, specialty epoxy putty that mixes in just one minute for repairs to damp, wet
areas and underwater surfaces. It contains a fading dye and becomes "fiberglass white" after
mixing. It may be applied underwater, in either fresh or salt water and will bond tenaciously to
substances such as fiberglass, metal, wood, concrete, ceramic, glass, etc.
Features:
• No measuring, mess or waste
• Excellent as an adhesive
• Can be applied underwater
• Does not yellow when exposed to UV light
• Authorized by the USDA for use in federally
inspected meat and poultry plants
Applications:
• Perfect for patching dings, scratches, cuts, gouges
and holes in fiberglass, metal and wood.
• Repairs fittings, pipes, electrical connections,
leaking gaskets, fuel tanks, etc.
030111
070113
30
PHYSICAL PROPERTIES:
Working Life (min.) .................................................. 20
Shelf Stability ......................... 6 months (min. @ 75oF)
Shore D Hardness (full cure, 24 hrs.) ...................... 75
Lap Shear Tensile Strength on Steel
(1" x 1" x 1/16") ............................................ 700 Lbs.
Temperature .................................... 250oF continuous
Limitations ....................................... 300oF intermittent
Chemical Resistance: Resistant to hydrocarbons,
ketones, alcohols, esters, halocarbons, aqueous salt
solutions and dilute acids and bases.
Electrical Resistance ....................... 30,000 megohms
Dielectric Strength ................................... 300 volts/mil
Shrinkage .............................................. Less than 1%
Non-Volatile Content........................................... 100%
Compression Strength .................................12,000 psi
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.5
Adhesives and Sealants
E-Z Poxy™ Concrete
Part #74526 – 4 oz.
(Repairs and rebuilds anything made of concrete)
A hand mixable, fast curing epoxy putty stick that mixes in one minute to provide permanent repairs
to concrete. Simply knead putty and apply to damaged area. Can be drilled, filed, tapped, sanded,
machined, sawed or painted after one hour.
Features:
• Use as putty or adhesive
• No measuring, mess or waste
• Fast – sets in 10 minutes
• Adheres to damp surfaces
• Hardens under water
• Authorized by the USDA for use in federally
inspected meat and poultry plants
Applications:
• Perfect for cracked and spalled concrete, setting
anchors, and filling cracks, gaps, holes, etc.
PHYSICAL PROPERTIES:
Work Life ................................................................ 4-7 minutes
Shelf Stability @ 75oF ............................. 24 months (minimum)
Hardness (Shore D) (full cure 1 hour) .....75-85 (ASTM D2240)
Lap Shear Tensile Strength ............................... (ASTM D1002)
On Steel (1” x 1” x 1/16”) ..................................... 500-800 lbs
On Concrete ..................................................Concrete failure
Compressive Strength ................. 12,000 lbs/in2 (ASTM D695)
Density.......................................... 2.005 gm/cm3 (16.72 lb/gal.)
Prox. 5/16” Bolt Pullout .............. >2 tons (Dennison Block Test)
Shrinkage ..................................................<1% (ASTM D2566)
Non-Volatile Content.........................................................100%
Upper Temperature Limit
Continuous ..........250oF
Intermittent ...............300oF
Chemical Resistant to hydrocarbons, ketones, alcohols, esters,
halocarbons, aqueous salt solutions and dilute acids and bases.
E-Z Poxy™ Copper
Part #74501 – 4 oz.
(Hardens like metal to form a copper repair)
A hand-kneadable, copper reinforced epoxy putty that hardens to an extremely tough and durable
substance with exceptional adhesion. It can be drilled, tapped, filed, machined, etc. High pressure
hot water pipes, tanks and radiators can be restored to service after just 60 minutes!
Features:
PHYSICAL PROPERTIES:
• No measuring, mess or waste
Density........... 15.8 lb./gal. (1.9 gm/cm3)
• Fast – cures in less than 60 minutes
Compression Strength ...........18,000 psi
Tensile Strength .......................6,000 psi
• Contains real copper
Modulus of Elasticity ..............6 x 105 psi
• Certified to NSF/ANSI Standard 61 for use in
Adhesive Strength ......................700 psi
contact with potable water
Izod Impact ......... 0.3 ft.-lb./in. (notched)
• Authorized by the USDA for use in federally
Hardness (Shore D)........................... 85
Maximum Use Temp ........300oF (149oC)
inspected meat and poultry plants
ELECTRICAL PROPERTIES:
Applications:
Volume Resistance ...... 5 x 1015 ohm-cm
• Perfect for high pressure hot water pipes, sealing leaks
Dielectric
in pipes, elbows, joints, sleeves, sink traps, drains, etc.
Strength ........400 volts/mil @ 0.125 in.
• Can also be used as an adhesive.
E-Z Poxy™ Cups
30
Part #74514 – 1.2 oz.
(Pre-measured, single use, fast setting epoxy)
Unique, pre-measured epoxy cups contain both resin and hardener in one convenient
package. Self-package mixing eliminates measuring, squeeze tubes and weighing scales. No
mess, guesswork or waste. Components are color-coded to assure complete mixing.
Features:
• Fast cure mixer cups
• Convenient self-package mixing
• Superior strength epoxy bonds almost anything
• No mess, no waste
• Bonds virtually any material
TECHNICAL DATA:
Parts fixture in 5-15 minutes, full cure in 24 hrs
Creep Strength .................................. excellent
Peel Strength ........................................... good
Working Life.........................5 minutes @ 70oF
Chemical Resistance ......................... excellent
Temperature ........................................... 180oF
Applications:
• Bonds wood, ceramic, glass, marble, metal, plastic, concrete, stone, brick and much more.
30.6
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
030111
070113
Adhesives and Sealants
E-Z Poxy™ Fast Set
Part #74530 – 1 fl. oz.
(Strong, permanent epoxy adhesive)
Provides a durable repair resistant to solvents, moisture and impact.
Features:
• Easy-to-use dual piston dispenser
• Clear
• Sets in just 5 minutes
• Waterproof and solvent resistant
Applications:
• E-Z Poxy™ Fast Set bonds wood, metal,
plastic, ceramic, glass, china, tile,
fiberglass and laminates.
E-Z Poxy™ Plastic
Part #74527 – 4.0 oz.
(Restore, rebuild and repair ABS, CPVC and PVC plastic)
A patented, hand mixable epoxy putty that forms a durable bond to all major plastic types except
polyolefins (polyethylene/polypropylene). When mixed together, the materials combine to form
a polymer compound that can be molded into shapes, wrapped around or used to build up and
repair just about anything made from rigid or semi-flexible plastics. After 2-3 hours, it can be drilled,
sawed, carved, sanded or painted. Contains a fading
PHYSICAL PROPERTIES:
blue dye and becomes white after mixing.
Features:
• No measuring, mess or waste
• Fast – sets in 10 minutes
• Adheres to damp surfaces
• Hardens under water
Applications:
• Perfect for rebuilding rigid and semi-flexible plastics
• Repairing automotive trim, appliance parts, outdoor
furniture and more
• Sealing leaks in plastic plumbing pipe
Work Life (Minimum) ..............................20-25 Minutes
Shelf Stability ........................ 24 months (min. @ 75oF)
Shore D Hardness (full cure 24 hrs.) ................... 60-70
Lap Shear Tensile Strength
(1" x 1" x 1/16") ..................................500-800 on pvc
Compression Strength lbs./in.2 ......................... 12,000
Density................................. 1.6, 13/4 (gm/cm3, lb.gal.)
Shrinkage .............................................................. <1%
Non-Volatile Content............................................ 100%
Electrical Resistance .........................30,000 megohms
Dielectric Strength .................................... 300 volts/mil
Temperature ....... 250oF continuous, 300oF intermittent
Chemical Resistance: Resistant to hydrocarbons,
ketones, alcohols, esters, halocarbons, aqueous salt
solutions and dilute acids and bases.
E-Z Poxy™ Wood
Part #74503 – 1.94 oz.
(Restore, rebuild and repair all types of wood)
Repairs wood with an epoxy compound many times stronger than the wood itself. Simply knead
putty and apply to damaged surface. It can be drilled, nailed, sanded, stained or painted – all within
60 minutes! Also eliminates the need to replace
PHYSICAL PROPERTIES:
expensive damaged molding, trim, door jambs & furniture.
3
030111
070113
Features:
• No measuring, mess or waste
• Fast – cures in 45 minutes
• Will not dry out like conventional putties
• Simplifies wood repairs
Density...................... 6.7 lb./gal. (0.8 gm/cm )
Compression Strength ....................18,000 psi
Tensile Strength ................................6,000 psi
Modulus of Elasticity .......................6 x 105 psi
Adhesive Strength ...............................700 psi
Izod Impact .................. 0.3 ft.-lb./in. (notched)
Hardness (Shore D)............... 75 after 90 min.
Maximum Use Temp. ................250oF (121oC)
Applications:
• Perfect for repairing damaged furniture, rebuilding or
fabricating wood parts, repairing stripped screw holes.
• Can also be used as an abrasive.
ELECTRICAL PROPERTIES:
Volume Resistance ............... 5 x 1015 ohm-cm
Dielectric
Strength ................ 400 volts/mil @ 0.125 cm
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.7
30
Adhesives and Sealants
Fast-Fix™ Epoxy Patch Kit
Part #74506
(Pre-measured, single use, fast setting fiberglass epoxy patch)
Repairs cracks and holes in pipe and hose. Pre-measured fiberglass patch is ideal for
repairing cylindrical surfaces (hose, pipe, etc.) and for flat surfaces such as watertanks. Just
blend the components together in the package and apply to any clean surface. It will cure in
approximately 20 minutes – even on wet surfaces!
Features:
• Unique pre-measured package contains 4" x 12" patch and rubber gloves
• Permanently repairs virtually any surface
• Withstands 600oF and 150 psi pressure
• Safe for drinking water systems (Tested for potability using EPA approved standard testing methods.)
• Paintable
Fast-Fix™ Pipe & Hose Repair Kit
Part #74507
(Pre-mixed, air activated, single use, fast setting fiberglass epoxy wrap)
Resin impregnated fiberglass tape sealed in a foil pouch. Once opened, the tape is simply
wrapped around any hose or pipe, and will set as hard as steel in just 30 minutes. It is ideal
for stopping leaks and keeping on hand as an emergency repair kit.
Features:
• Unique pre-measured package contains 2" x 60" impregnated patch and rubber gloves
• Air activated resin
• Permanently repairs virtually any surface
• Withstands 600oF and 150 psi pressure
• Safe for drinking water systems (Tested for potability using EPA approved standard testing methods.)
• Paintable
Applications for #74506 & #74507:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
30
•
•
•
•
•
•
•
•
•
30.8
Oil Pipelines
Gas Pipelines
Off-Shore and Petroleum Refineries
Steam Lines
Plant Piping Systems
Tanks
Container Linings
Industrial Irrigation Systems
Commercial Irrigation Systems
Underwater Cable Encapsulation
Underwater Piling Encapsulation
Underground Piping Structures
Waste Water Treatment Plants
Pneumatic Hoses and Lines
Piping for Hydronic Heating
HVAC Systems
Kitchen and Bath Plumbing
Underground Sprinklers
Irrigation Systems
Pool and Spa Piping
RV Water Piping Systems
Marine Water Piping Systems
Boat Hulls
Automobile Radiator Hoses
Automobile Exhaust Systems
Farm Machinery and Equipment
Marine Exhaust Systems
TECHNICAL DATA:
Number of Piles .....................................................................9
Fabrication Method ............................................... Wet Lay-up
Cure Time at 75oF.................................................. 30 Minutes
Barcol Hardness ..................................................................53
Dielectric Strength ............................................... 16,060 Volts
Heat Resistance ......................................................... 1,100oF
CHEMICAL RESISTANCE:
Immersion Chemical
Total Immersion Time
Effect
Acetone .................................30 Days .............. Softened
Diesel Fuel.............................30 Days .............. No Effect
Ethyl Alcohol ..........................30 Days .............. Soft, Rubbery
Gasoline ................................30 Days .............. No Effect
30% HCL ...............................30 Days .............. Softened
Toluene ..................................30 Days .............. Softened
MEK .......................................30 Days .............. Soft, Rubbery
Chlorine .................................30 Days .............. No Effect
MECHANICAL PROPERTIES:
Structure
Method
PSI
Flexural Strength ............ ASTM D 709-71 ........ 16,100
Tensile Strength .................ASTM D 638........... 24,900
Compression Strength .... ASTM D 695-77 ........ 26,600
Bond Strength.......................................................................98
4 Layers to Total Obliteration
Spray Penetration Test (4 layers recycled from 50oF-90oF)
Temperature Cycle Test (with no delmination or loss of bond)
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
030111
070113
Adhesives and Sealants
Fast Weld Adhesive & Welding Powder
(Double Bond Performance)
Part #74489
Adhesive - 28 g
Welding Powder - 40 g
The Adhesive bonds most materials instantly. These materials are rubber, glass, copper,
aluminum, steel and most plastics. The Welding Powder is used to repair all types of holes,
cracks, gaps and can produce a strong weld seam to support the repair, just like solder or
welded joints.
Features:
• Beyond Super Glue
- A combination of instant adhesive plus a welding powder.
• An Incredible Tool
- Repairs almost anything.
• Save Time & Money
- An advanced polymer adhesive that can bond quickly, sometimes instantly.
• Double Bond Performance
- The welding powder enables even stronger bonds!
Benefits:
• High strength, bonds in seconds
• Can bond almost any material to itself or to another material
• Will not dry out in the container
• Adhesive dries crystal clear
Applications:
• Use on rubber, glass, copper, aluminum, steel and most plastics
• Repair holes, cracks, and gaps
• Can be filed, drilled, sanded, and painted almost immediately
30
030111
070113
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.9
Adhesives and Sealants
Instant Adhesive
Part #74516 – 1/3 fl. oz.
(Instant, high strength, cyanoacrylate adhesive for non-porous surfaces)
Ultra-high performance, versatile adhesive bonds metal, rubber, plastic and glass instantly.
Red Lion Instant Adhesive works where others fail, providing the strongest bond on hard-tobond surfaces.
Features:
• Permanent, super strength bond
• Easy to use
• Bonds instantly
• Saves time, money, labor and mess
Applications:
• Bonds metal, rubber, plastic and glass
Instant Adhesive Gel
TECHNICAL DATA:
Color ........................................................Clear
Gap Fill .................................................... .004"
Viscosity cP ................................................. 40
Tensile Shear Strength PSI .................... 2,500
Temperature
Range ............ -65oF to 180oF (-54oC to 82oC)
Cure Speed
Fixture.....................................20-40 seconds
Full ................................................... 24 hours
Part #74525 – .10 oz.
(Instant, high strength, cyanoacrylate adhesive for porous surfaces)
Ultra-high performance, versatile adhesive bonds wood, paper, leather, fabric, metal, rubber,
plastic and glass instantly. Red Lion Instant Adhesive Gel works where others fail, providing
the strongest bond on hard-to-bond surfaces. Particularly suited for bonding porous or
absorbent materials such as wood, paper, leather or fabric.
Features:
• Permanent, super strength adhesive
• Bonds instantly – no waiting for product to cure
• Easy application – no mixing required
• Saves time, money, labor and mess
Applications:
• Bonds wood, paper, leather, fabric, metal, rubber,
plastic and glass
Just for Copper
TECHNICAL DATA:
Color ........................................................Clear
Viscosity cP ................................................Gel
Tensile Shear Strength PSI ...... 1,000 to 3,200
Temperature
Range ............ -65oF to 180oF (-54oC to 82oC)
Cure Speed
Fixture/Full ..............................20-40 seconds
Full ................................................... 24 hours
Part #74553 – 1.85 oz.
(Solderless copper bonding)
Solderless copper bonding, bonds rigid copper pipes and standard fittings without heat.
Changes from a liquid to a polyacrylic solid to provide maximum strength between tube
and fitting. Works even when pipes are wet. No mixing, just shake, squeeze and apply.
Is an insulator and will not conduct electricity.
30
Features:
• Easy to use, permanent cold weld for installing and repairing rigid copper pipe in
potable hot and cold water
• Provides same permanent weld as hot solder
• Temperature range from -40oF to 245oF
• Holds 200psi 7 seconds after bonding; holds 500psi 4 hours after bonding
• Sets in 5 seconds; cures in 7 minutes
• 50g bottle makes up to 200 welds
• Approved for potable water and EPA National Drinking Water Standards
Applications:
• For use on pipes up to 2 diameter
• Use on copper pipe and copper and brass fittings
30.10
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
030111
070113
Adhesives and Sealants
Pow-R-Bond Adhesive
TM
Part #74187 – 13.25 oz.
(Spray adhesive)
High strength, fast setting, permanent adhesive for all heavy duty general purpose bonding
applications. Lace-like pattern sets up quickly for high contact strength. Dries in minutes.
High temperature resistance to 140oF (60oC).
Features:
• Superior strength – handles heavy duty applications
• Permanent bond – assures durability
• Fast assembly – minimizes downtime
• Multi-purpose – provides versatility
• Heat resistant – for high temperature applications
Applications:
• Ideal for laminates, trim, signs, kick plates, wood working, maintenance and
asbestos removal
• Adheres to most surfaces including wood, metal, glass, plastic, etc.
Spray Adhesive
Part #74130 – 13.25 oz.
(Multi-purpose, permanent, fast setting)
A multi-purpose light-duty spray adhesive that works on virtually any surface where an
adhesive is needed. Remains tacky for several minutes to allow for respositioning.
Features:
• Strong permanent bond – assures effective repairs and secure assembly
• 3-position valve – allows proper dispensing of product
• General purpose – covers virtually any light-duty applications
• Temperature Range: 120oF continuous, 200oF intermittent
Applications:
• Ideal for gaskets, trim, foam, ceramics, ferrous and no-ferrous metals, cardboard, etc.
3M™ Spray Adhesives
(Series 20 Aerosol Spray Adhesives)
P/N 74605 – 13.8 oz.
P/N 74606 – 13.8 oz.
P/N 74607 – 13.8 oz.
P/N 74605 – 3M™ Multi-Purpose 27 Spray Adhesive
Extremely versatile adhesive is ideal for bonding paper, cardboard, fabrics, soft foams
and many other lightweight materials.
• Fast tack
• Lightweight applications
• Mist spray pattern
30
P/N 74606 – 3M™ Foam & Fabric 24 Spray Adhesive
Fast-tack adhesive bonds foam to metal, wood and many other substrates (ideal for upholstery).
• Aggressive tack
• Foam-tearing strength
• Variable width lace spray pattern ensures precise placement.
P/N 74607 – 3M™ Woodworking 20 Spray Adhesive
High strength, fast-grabbing adhesive forms powerful, permanent bonds.
• Fast grab
• Bonds wood, laminates, metals, plastics and more
• Variable width lace spray pattern ensures precise placement
030111
010114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.11
Adhesives and Sealants
CPVC Cement – Orange
Part #74552 – 16 oz.
(Cement for CPVC pipe and fittings)
Medium-bodied cement for use on CPVC pipe and fittings up to 6” diameter.
Features:
• Exceeds new environmental requirements and meets various California district rules
• Low V.O.C.
• Apply at temperatures 40oF to 90oF
• Exceeds ASTM D-2846, F-493
• NSF and UPC listed
Applications:
• For C.T.S. (copper tube size) and Schedule 80, potable water pressure pipe
PVC-ABS-CPVC Cement
Part #74550 – 16 oz.
(Multi-purpose cement)
Medium-bodied clear cement for ABS, PVC or CPVC up to 6” diameter.
Features:
• Apply at temperatures 40oF to 100oF
• Exceeds performance requirements of ASTM D-2564, D-2846, D-2235 and F-493
Applications:
• Recommended for pipe Schedule 40 and Schedule 80 potable water, pressure pipe, gas,
conduit and DWV
PVC and CPVC Primer – Purple
Part #74549 – 16 oz.
(All-purpose primer/cleaner)
Removes surface dirt, grease and grime as well as softens pipe in preparation for solvent
cement.
Features:
• Exceeds new environmental requirements and meets various California district rules
• Less aggressive than clear and standard purple primers
• Purple tint for verification for code
• Low V.O.C.
• Apply at temperatures 40oF to 100oF
Applications:
• For PVC and CPVC pipe and fittings
30
PVC Cement – Clear
Part #74551 – 16 oz.
(Cement for PVC pipe and fittings)
Medium-bodied clear cement for use on PVC pipe and fittings up to 6” diameter for Schedule 40
and Schedule 80.
Features:
• Exceeds new environmental requirements and meets various California district rules
• Low V.O.C.
• Apply at temperatures 40oF to 100oF
• Exceeds ASTM D-2564
• NSF and UPC listed
Applications:
• Recommended for gas, conduit, drain, waste and vent pipe
30.12
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
030111
Adhesives and Sealants
Super Adhesive Sealant
Part #74510 – 3.7 fl. oz.
(Multi-purpose, flexible, high strength adhesive)
A versatile, high-performance industrial adhesive and sealant which provides exceptional
mechanical and chemical bonding in plant, fleet, commercial and contractor applications. Adheres
to and seals all woods, metals, concrete, masonry, ceramics, rubber, fiberglass, glass and plastics.
Features:
• Superior strength
• Extremely flexible
• Abrasion resistant
• Paintable
• Waterproof
• Self-leveling
Applications:
• Plant and Building Maintenance
• Transportation
• Marine
• Electrical
• Rubber Goods and Plastics
• Tools and Fasteners
• Construction and Carpentry
TECHNICAL DATA:
Temperature Range ....... -40oF to 150oF
Tensile
Strength ...... 3500 lb/in.2 (ASTM D-412)
Elongation............900% (ASTM D-412)
Dielectric Strength ............ 400 volts/mil
Dry Time ...................... Tack: 5 minutes
Paintable: 24 hours
Super Adhesive Sealant UV
Part #74554 – 10.2 fl. oz.
(Multi-purpose, ultra-violet light resistant high strength adhesive )
This multi-purpose, clear adhesive is formulated for use in applications that may be exposed
to ultra-violet light. Adheres to wood, metal, rubber, glass and most plastics. It is not for use on
StyrofoamTM. Its flexible bond resists cold temperatures, yellowing, cracking and embrittlement. Can
be submerged in fresh and salt water after complete cure. Great for bonding objects subject to wear
and to vibration. Safe for applications exposed to dilute acids and dilute caustics. Recommended for
all industrial applications where UV resistance is required.
Features:
• UV resistant formula
• Industrial strength
• Extremely flexible
• Waterproof
• Paintable
• Self-leveling
Applications:
• Plant and Building
Maintenance
• Transportation
• Marine
• Electrical
• Rubber Goods & Plastics
• Tools and Fasteners
• Construction & Carpentry
Liquid Electrical Tape
TECHNICAL DATA:
Full Cure Time ........................Thin film 24 hours,
................................................Thick film 48-72 hours
Tensile Strength ......................3500 lb./in.
Elongation...............................900% (ASTM D-412)
Service Temperature Range ...-40oF to 150oF
Paint-Over Time......................24 hours
Dielectric Strength ..................400 V/mil
Part #74547 – 4 fl. oz.
(Brush applicator cap)
Forms a protective dielectric coating on electrical connections to seal out moisture and prevent
corrosion. Wil not peel or unravel. Flame retardant. Service temperature range is -30oF to +255oF.
Completely waterproofs connections and can be applied to irregular shaped or
hard-to-reach conditions.
Features:
• Seals and protects electrical connections
• Adheres to all metal, plastic, vinyl, rubber
and composite surfaces
• Stops terminal screws from loosening from vibration
• Safe and easy to use
• Fast drying
• Dielectric strength 1000-1500 volts/mil
Applications:
• Bilge pumps, outdoor exposed wiring, sprinkler pumps, timers, underground wiring, outdoor
lighting fixtures, instruments, computers... anywhere a weatherproof and dependable
connection is needed.
010114
030111
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.13
30
Adhesives and Sealants
RTV Gasket Maker
Part #74128 (White) – 8 oz.
Part #74131 (Black) – 8 oz.
Part #74132 (Blue) – 8 oz.
Part #74133 (Clear) – 8 oz.
(Tough silicone adhesive sealer/gasket maker)
The ultimate gasket maker and sealer in an easy to use dispenser.
It adheres to and bonds natural and synethic fibers, metal, glass, wood,
rubber, ceramic, painted and plastic surfaces. Seals against water, air, chemicals, oils and grease.
Fills crevices and irregularities in joints. Waterproofs porous materials. Perfect for weatherstripping. Insulates against shock and vibration and a great electrical insulator. A perfect gasket
maker for just about anything. When fully cured and washed, this product meets the following
specifications: FDA Regulation No. 21 CFR 177.2600, MIL-A-46106, per current revision and type,
and TT-S-001543A. This product is suitable for use in federally inspected meat and poultry plants.
Features:
• One-part silicone adhesive sealant
• Temperature range -80oF to +500oF (450oF continuous)
• Insulates and weatherproofs
Applications:
• For use on gasketing pumps, oil pans, valve covers,
gear boxes, compressors, etc.
• Seals windows, pipe joints and parts
• Bonds gaskets, appliance parts, sign letters
• Caulks joints, duct work, equipment housings
RTV TUBE EXTENSION TIP
Part #16065
Screws on RTV dispensers for
precision application of sealer
NOTE: Do not use in direct contact with fuel oil, gasoline, acid or caustic materials. Not for use on head gaskets or carburetor base.
RTV Gasket Maker (Hi-Temp Red)
Part #74153 – 8 oz.
(High temperature resistant, tough silicone adhesive)
The ultimate gasket maker and sealer features the most advanced technology in an easy
to use dispenser, giving a uniform bead of any size or shape. It meets O.E.M. low volatile
specifications for use with oxygen sensor equipped engines. Meets GM specs.
Features:
• Ultimate gasket maker
• Low odor
• Low volatile and non-corrosive
• Temperature range -60oF to +600oF
(500oF continuous)
• Insulates and weatherproofs
30
Applications:
• For use on gasketing pumps, oil pans, valve
covers, gear boxes, compressors, etc.
• Seals windows, pipe joints and parts
• Bonds gaskets, appliance parts, sign letters
• Caulks joints, duct work, equipment housings
NOTE: Do not use in direct contact with fuel oil, gasoline, acid or caustic materials. Not for use on head gaskets or carburetor base.
30.14
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
030111
Adhesives and Sealants
RTV Gasket Maker/Sealer (Tube)
(Tough silicone adhesive in a caulking gun cartridge)
Part #74542 – White
Part #74548 – Black
Part #74543 – Blue
Part #74541 – Clear
The ultimate gasket maker and sealer in a caulking gun cartridge.
Ideal for use wherever a strong, permanently elastic weatherproof
adhesive sealant is needed. This product has excellent adhesion characteristics, high chemical
resistance and will not sag or shrink from severe temperature extremes. As an instant gasket
maker, this product replaces a wide range of cork, paper, asbestos, felt and metal gaskets.
Reduces inventory – eliminates need to stock conventional gaskets. Reduces downtime – gets
equipment back in operation fast. (Use with P/N 8253 Caulking Gun).
10.3 oz. Cartridges
Features:
• 100% silicone rubber
• Permanently flexible
• Withstands temperatures -85oF to 450oF (-51oC to 232oC)
• Adheres to most surfaces
• Insulates
• For interior and exterior use
Applications:
• Use for sealing cracks in machinery, heating and ventilating duct work, plumbing fixtures,
electrical connections, low pressure water and drain pipes.
• Bonds nameplates, machinery flanges, glass, signs and electrical insulation.
• Ideal for caulking windows, doors, walls, ceiling cracks and crevices
RTV Gasket Maker/Sealer
(Hi-Temp Red Tube)
Part #74544 – 10.3 oz.
(High temp resistant, tough silicone adhesive in a caulking gun cartridge)
The ultimate gasket maker and sealer in a caulking gun cartridge. Ideal for use wherever
a strong, permanently elastic weatherproof adhesive sealant is needed. This product has
excellent adhesion characteristics, high chemical resistance and will not sag or shrink from
severe temperature extremes. It can be used in a wide temperature range of -85oF to 600oF
(500oF continuous). As an instant gasket maker, this product replaces a wide range of cork,
paper, asbestos, felt and metal gaskets. Reduces inventory – eliminates need to stock
conventional gaskets. Reduces downtime – gets equipment back in operation fast.
(Use with P/N 8253 Caulking Gun).
Features:
• 100% silicone rubber
• Permanently flexible
• Withstands temperatures -85oF to 600oF (-51oC to 315oC)
• Adheres to most surfaces
• Insulates
• For interior and exterior use
30
Applications:
• Use for sealing cracks in machinery, heating and ventilating duct work, plumbing fixtures,
electrical connections, low pressure water and drain pipes.
• Bonds nameplates, machinery flanges, glass, signs and electrical insulation.
• Ideal for caulking windows, doors, walls, ceiling cracks and crevices
030111
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.15
Adhesives and Sealants
Rapid Seal
Part #74572 – Black / 18 oz.
(Rubberized Sealant – Petroleum Asphalt Resin)
Rapid Seal rubberized sealant seals leaks in gutters, flashings, roofs, and skylights. It is excellent as sealer
after pruning trees, and also can be used as a sealant on pails, planters, and trash cans.
Features
•
•
•
•
•
•
•
•
•
•
Tough
Flexible Elastic Barrier
Temporary or Permanent
Works On a Variety of Surfaces
Seals Out Moisture
Fast Dry
Can Be Top Coated
Deadens Sound
Resists Temperature Extremes
Resists Rust, Road Salts, Alkali and Acids
Seal-It
Applications
•
•
•
•
•
•
•
Skylights
Flashings
Air Vents
Gutters
Antenna Installations
Small Cracks / Holes in Driveways
Tree Shrub Pruning
Part #74573 – Black / 15 oz.
Part #74574 – Clear / 15 oz.
Part #74578 – White / 15 oz.
Part #74579 – Silver / 15 oz.
(Thermoplastic Elastomer Resin)
A unique spray product that leaves a firm coating which stays flexible. Will not sag or drip. The coating is
impervious to water. The film will not freeze or crack in cold, is abrasion resistant and won’t peel.
Economical, quick, and easy to use. Seals out rust and corrosion.
Features
• Unique Spray Product
• Leaves a Flexible Firm Coating
• Will Not Sag or Drip
• Impervious to Water
• Will Not Freeze or Crack in Cold
• Abrasion Resistant
• Does Not Peel
• Economical
• Quick and Easy
• Seals Out Rust and Corrosion
Applications
• Flashings / Skylights
• Windows / Doors
• Air vents
• Concrete
• PVC
• Gutters
• Shingles / Siding
• Semi Trailers
• Roofs on Campers
Insulating Expandable
Foam Sealant
30
Part #74575 – 12 oz.
(A unique one part urethane foam which expands as it dries and solidifies)
Sprays as a liquid then expands and cures to a durable semi-rigid closed cell foam insulation. Each can
dispenses over 800 linear feet of product when sprayed in a 3/8'' cured bead. Great for sealing headers,
outlets, door frames, outside faucets, and around air vents. Fills cracks and plugs holes that caulk won't. Plug
the entrance of insect or rodent holes. Seals out Radon Gas. Deadens sound when applied to sheet metal.
Features
• Forms a water-resistant, weather-resistant
and airtight bond on masonry, wood, metal, glass, & most plastics
• Keeps pollutants out as well as noise
• Dries tack free in 10 minutes
• Cures completely in 8 to 24 hours
• Easy to use, conforms to any shape as it expands
• Foam expands 2 to 3 times in size
30.16
Applications
• Energy conservation
• Air Conditioning
• Ventilation Ducts
• Heating Ducts
• Plumbing
• Window A/C Units
•Spas
• Hot Tubs
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
• Boats
• RVs
• Electrical Equipment
•Appliances
• Refrigeration Units
•Carpentry
• Masonry
• Auto/TruckDoors
090113
030111
Adhesives and Sealants
Cooling System Sealant
Part #74557 – 11 oz.
(Seals leaks quickly and conveniently)
Cooling System Sealant quickly stops minor radiator leaks, seals hairline cracks in engine blocks
and heads and stops seeping around gaskets and hoses. Contains ultra small refined organic
fibers, an organic buffer to deter rust and corrosion, and a suspension thickener.
Features:
• Stops minor radiator leaks quickly
• Seals hairline cracks in the block or head
• Stops seeping around gaskets and hose connections
Applications:
• Automotive dealerships, independent automotive shops, service stations, automotive retailers,
farm and construction equipment repair, school auto shops
Threadlocker
(Strong, temporary lock for threaded fasteners)
Part #74490 – 0.338 fl. oz.
Part #74513 – 1.20 fl. oz.
This medium-strength, general purpose thread locking compound is ideal for all nut and bolt
applications and eliminates self-loosening. It is suitable for temperatures up to 300oF, prevents
threads from rusting and is removable with hand tools.
Features:
TECHNICAL DATA:
• Covers all threadlocking applications
Gap Fill..................................................... .005"
Viscosity cP...................1200/5000 Thixotropic
• "Capillary action" gap fill – prevents movement of
Torque in. lbs. (Break/Prevail)................. 80/50
screw threads and eliminates self-loosening
Temperature
• Anti-corrosion formulas prevent rusting of thread
Range........... -65oF to 300oF (-54oC to 149oC)
• Fast cure without cracking or shrinking –
Cure Speed
(Fixture/Full).......................20 min. / 24 hours
enables quick assembly with minimum downtime
• Easy application – no mixing required
• Authorized by USDA for use in federally inspected meat and poultry plants
• Saves time, money, labor and mess
Applications:
• Can be used with all metals, glass, ceramics and many thermoset plastics
Threadlocker Gels
Part #74567 10gm Medium Strength Blue
Part #74568 10gm High Strength Red
(Formulated to provide "liquid reliability")
The gel twist threadlockers will not drip or run like traditional liquid threadlockers and is easily
portable. Threadlocker gels stay on the part which reduces waste and makes it great for use in
vertical applications. No more liquid drips or solid stick globs to deal with. No more mess to clean
or costly waste to worry about. The extended nozzle allows for easy application in "hard-to-reach"
locations.
Features:
• Locks and seals while preventing parts from
loosening due to vibration
• Protects threads from corrosion
• No drips, runs, spills or leaks
• Patent-pending formulation & pin-point applicator
• Gel stays where you want it . . . on the part
• Applies clean and package stays clean
• Great for "hard-to-reach" and vertical
applications
• Easily portable
• No mess and no waste –
time and cost savings!
Applications:
All-Purpose Medium Strength Blue – Ideal for all nut and bolt applications 1/4" to 1" (6mm to
25mm). Great for hard-to-reach and vertical applications. Removable with hand tools for easy
disassembly.
High Strength Red – Ideal for heavy-duty applications 3/8" to 1" (10mm to 25mm) and greater.
Well suited for permanently locking studs. Requires heat or special tools for removal.
030111
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.17
30
Adhesives and Sealants
Stud Lock & Bearing Mount
Part #74491 – 0.338 fl. oz.
Part #74515 – 1.20 fl. oz.
(High temperature resistant adhesive for locking studs and bearings)
A very high-strength adhesive for locking and sealing all fasteners up to 1" diameter and bearings.
Ideal where high viscosity, shear strength and rapid cure speed are necessary. It is also ideal for
tamper proofing where a difficult removal is desired. Stud Lock and Bearing Mount is suitable for
temperatures up to 300oF, prevents rusting of threads and is removable with heat and hand tools.
Features:
TECHNICAL DATA:
• Covers all threadlocking applications
Gap Fill..................................................... .007"
• Extremely versatile – can be used with all metals,
Viscosity cP................................................ 500
glass, ceramics and many thermoset plastics
Torque in. lbs. (Break/Prevail)............. 160/320
• "Capillary action" gap fill – prevents movement of
Temperature
Range........... -65oF to 300oF (-54oC to 149oC)
screw threads and eliminates self-loosening
Cure
Speed
• Anti-corrosion formulas prevent rusting of thread
(Fixture/Full).......................20 min. / 24 hours
• Fast cure without cracking or shrinking –
enables quick assembly with minimum downtime
• Easy application – no mixing required
• Authorized by USDA for use in federally inspected meat and poultry plants
• Saves time, money, labor and mess
Applications:
• Can be used with all metals, glass, ceramics and many thermoset plastics
Thread Sealant Hydraulic/Pneumatic Part #74524
(Seals and locks hydraulic and pneumatic fittings)
1.69 fl. oz.
Specially formulated for both hydraulic and pneumatic systems. Designed to seal and lock
hydraulic and pneumatic fittings, servomechanisms and fine-filtration systems. It contains
no fillers and will not foul valves or fluid filtering systems. It is suitable for temperatures up to
300oF and rated for sealing pressures to 10,000 psi.
TECHNICAL DATA:
Features:
Viscosity cP.................................. 14,000
• Medium strength for high pressure fluid power systems
Breakaway
Torque N.m. (lb./in.)........ 2 to 3 (8 to 24)
• "Capillary action" gap fill – prevents
Temperature.....................
-65oF to 300oF
movement of threads and eliminates self-loosening
Range......................... (-54oC to 149oC)
• Fast cure without cracking or shrinking –
Cure Speed
enables quick assembly with minimum downtime
(Fixture/Full)..............20 min. / 24 hours
• Easy application – no mixing required
For more information,
• Saves time, money, labor and mess
see Technical Bulletin #30.022
Applications:
• Hydraulic and pneumatic fittings, servomechanisms and fine-filtration systems
30
NOTE: Not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or
other strong oxidizing materials.
30.18
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
030111
Adhesives and Sealants
Loctite® Thread Treatment Sticks
(Solid performance in a semi-solid stick formula)
• 248 Medium Strength Threadlocker
• 268 High Strength Threadlocker
• PST ® 561 Thread Sealant
Part #17931
5-Piece Box Set
• C5-A® Copper Anti-Seize
• Silver Grade Anti-Seize
These patented new stick products offer great flexibility for tough applications, especially
overhead, under or around machinery and on components that cannot be moved. They're
compact, making them easy to carry from job to job and easy to store in a toolbox, tool belt or
pocket. They prevent rust and corrosion on various fastener sizes, easing disassembly and
reducing inventory carrying costs. The semi-solid formula also means they won't spill or leak.
Features:
• Convenient – small enough to be "pocket friendly"
• No leaks, drips or spills
• Keeps toolboxes, workbenches and hands clean
• Fast and easy to apply
• Solid formula – great for overhead use
• Functional for a full range of uses
• Color-coded caps for easy application identification
Applications:
• For threadlocking – completely fill
the root of the threads at the area
of engagment
• For thread sealing –
360o coverage is recommended
• Advance stick only as deep as the
threads you are applying to
248 Medium Strength Threadlocker Stick – Blue
Features:
• Eliminates loosening from vibration, shock and thermal expansion
• More reliable and cost effective than conventional mechanical fasteners
• Prevents rust and corrosion while sealing and protecting threads
• Removable with hand tools
Part #74561
0.67 oz. / 19 g
Applications:
• Machine tools and presses • Pumps and compressors • Mounting bolts • Gear boxes
268 High Strength Threadlocker Stick – Red
Features:
• Eliminates loosening from vibration, shock and thermal expansion
• More reliable and cost effective than conventional mechanical fasteners
• Prevents rust and corrosion while sealing and protecting threads
• Requires localized heat and hand tools for removal
Part #74563
0.67 oz. / 19 g
Applications:
• Heavy equipment • Suspension bolts • Motor, transmission and pump mounts
• Bearing cap bolts and studs • Formulated for heavy-duty applications
PST ® 561 Thread Sealant Stick – White
Features:
• Immediate low pressure sealing to 100 psi
• Controlled lubricity prevents galling
• Protects threaded areas from rust and corrosion
• Provides exceptional fluid compatibility and
chemical resistance
• Will not contaminate or clog lines
• Eases disassembly
030111
30
Part #74564
0.67 oz. / 19 g
Applications:
• Seals all types of metal tapered
threads and fittings to NPT specs
• Ideal for use in a broad range of
industries including chemical
processing, waste water
treatment and automotive
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.19
Adhesives and Sealants
Loctite® QuickStixTM 548TM Gasket
Eliminator ® Flange Sealant
Part #74569
0.63 oz. / 18 g
Features:
• Designed for rigid flange assemblies
• Forms a flexible, solvent resistant seal
• Offers excellent oil resistance on rigid flange sealing
• Seals up to 300oF (149oC)
• Fills gaps to 0.010"
• Sealing time: >3 hours with or without primer
Applications:
• Formulated with excellent oil resistance for rigid flange sealing, for example on
transmissions and cast metal housings
• Ideal for on-the-spot repairs or when a conventional gasket is not available
• For use on a variety of metal surfaces, including aluminum
Loctite® QuickStixTM 534TM Hi-Tack
Gasket Dressing
Part #74570
0.67 oz. / 19 g
Features:
• Allows a precut gasket to be positioned holding it in place for assembly
• Holds aggressively yet still allows for repositioning of the cut gasket
• Seals up to 300oF (149oC)
• Offers added control and ease of use
• Sealing time: 5 minutes to set
Applications:
• Seals and bonds rubber, cork, paper, felt and metal gaskets
• Ideal for use in applications requiring oil resistance
Loctite® QuickStixTM 668TM Retaining
Compound, High Temperature
Part #74571
0.67 oz. / 19 g
Features:
• Bonds non-threaded, cylindrical metal assemblies with gaps up to 0.005" diameter
• Provides typical shear strength of 1,870 psi after 24 hours
• Prevents fretting and corrosion of metal assemblies up to 400oF (204oC)
• Set-up time / full strength: 30 minutes / 24 hours
30
Applications:
• Fills the inner voids in close-fitting press fits, keyways and splines
• Mounts bearings and bushings
• Makes press fits even stronger
30.20
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
030111
Adhesives and Sealants
Teflon Pipe Sealant
Part #74545 – 1/2 Pint
Part #74546 – 1 Pint
®
(Superior performance, pipe fitting sealant with brush applicator cap)
Superior grade, non-hardening, easy-to-apply, heavy duty pipe thread sealant. It is formulated to a
thick past consistency and contains pure Teflon® powders and other PTFE resins to ensure a positive
seal with less effort. Withstands pressure to 10,000 p.s.i. (liquid), 2000 p.s.i (gas) and temperatures
from -250oF to +500oF (-157oC to +260oC) and is non-toxic. It remains flexible to allow easy
disassembly of connections.
Features:
• Prevents corrosion, seizing and galling
• Seals most threaded connections
• Resists chemicals, caustics and acids
• Non-staining and non-dripping
Applications:
• Designed for all pipe fitters, fabricators, plumbers and
mechanical contractors.
• Recommended for pipe thread connections servicing
chemicals, petroleum products, natural and LP gas,
solvents, refrigerants, water, steam, caustics and acids.
• Can be used on all pipe and threaded connections
with cast iron, malleable, brass, copper, stainless
steel, PVC, CPVC, ABS and polypropylene.
Teflon Pipe Sealant
®
Part #74511 – 1.20 fl. oz.
(Superior performance, food grade, paste pipe fitting sealant)
Specially formulated for rapid cure on stainless steel, carbon steel, monel and aluminum threads
and fittings. Can be used on all metal fittings. High lubricity allows easier assembly on worn or
damaged threads and prevents galling. Will not shred to clog or contaminate systems. Parts
are easily disassembled with a pipe wrench. Suitable for use with hydrocarbons (aromatics),
halocarbons [Freon®, perchloroethylene, trichloroethylene, organic acids (citric and acetic), alcohols,
mild mineral acids and bases (diluted and cold)]*. USDA accepted for use in federally inspected
meat and poultry plants.
CAUTION: Not for
use on plastic pipe.
May attack some
thermoplastics.
Airspace in tube
keeps contents liquid.
Features:
• Superior lubrication
• Seals all stainless steel and other metal fittings
• Outperforms all pipe dopes and tapes
• Temperature range -65oF to 400oF (-54oC to 204oC)
• Pressure resistance to 10,000 psi
SPECIFICATIONS:
Color .......................................................White
Viscosity ........................................550,000 cP
Pressure Resistance ...................... 10,000 psi
Seal to Operating
Pressure .................. Stainless Steel 3 hours
................................. Carbon Steel 30 minutes
Temperature
Range .........-65oF to 400oF (-54oC to 204oC)
Applications:
• Designed for all pipe fitters, fabricators, plumbers and mechanical contractors.
• Recommended for pipe thread connections servicing chemicals, petroleum products,
natural and LP gas, solvents, refrigerants, water, steam, caustics and acids.
• Can be used on all pipe and threaded connections with cast iron, malleable, brass, copper,
stainless steel, PVC, CPVC, ABS and polypropylene.
*Not recommended for oxygen systems. Freon and Teflon are registered trademarks of DuPont.
Screw Grab®
30
P/N 74562 – 0.5 fl. oz. / 15 ml
®
ScrewGrab is a friction gel that helps remove or tighten all types of fasteners - damaged or rusted
screws, nuts, and bolts. A single dab creates a positive grip between metal surfaces (new tests have
shown as high as 800%), that virtually eliminates tool wear and the stripping, rounding, or deforming
of fasteners
050111
030111
Features:
Applications:
• NOT a Glue
• Works Instantly
• Wipes CLEAN after use
• Non-corrosive
• Unlimited shelf-life
• ScrewGrab is approved for use on US Military
jets, and by the United Kingdom RAAF
• Stripped, rounded, deformed bolt heads/nuts
• Seized, rusted, or hard-to-reach spots
• Stops drill bits from turning in chuck
• Sloppy or mismatched sockets
• Removal of headlight frames, car moldings
• Apply to power driver for drywall or deck
screws
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.21
Adhesives and Sealants
3M™ Fire Barrier Sealant, CP 25WB+
(Premium, Intumescent Latex-based Sealant)
3M CP Sealant 25WB+ offers outstanding
fire performance plus a non-halogen formula.
P/N 74580, 10.1 fl oz Cartridge*
P/N 74581, 27 fl oz Cartridge
P/N 74582, 20 fl oz Sausage
P/N 74583, 5 Gallon Pail
P/N 74584, 2 Gallon Pail
• Rating – Provides up to 4 hour rating of UL systems tested
• Water base – easy cleanup, no special handling, routine disposal
• Intumescent – expands when heated to choke and seal around items consumed by fire
• Endothermic – releases chemically bound water to cool exposed surfaces
• Fast-dry – tack-free in approximately 10-15 minutes
• Red color for easy inspection
* Stock item (most widely used).
Please call for delivery on other 4 items.
3M™ Fire Barrier Moldable Putty
(Restores the Integrity of Fire-rated Building Construction)
Designed for use as a one-part,
100% solids intumescent firestop.
P/N 74585, Stick – 1.5'' x 6''
P/N 74586, Pad – 4''x 8'' x 1/8''
• Ideal for construction gaps, cable, insulated pipe, electrical conduit and metal pipe
• Designed to provide up to a 4-hour fire rating
• UL-classified for telecommunications applications (interduct, fiber optic and cables)
• Remains pliable and flexible
• Won’t dry out or crumble
• Convenient pad and stick form
• Non-halogen formula
• Reenterable
• Adheres to all common building surfaces including metal and plastic electrical boxes
• Provides draft and cold smoke seal even before temperature increases
• Intumescent and expands to form a hard char – prevents the transmission of hot gases & fire
• Great for building maintenance applications
30
30.22
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
010114
030111
Adhesives and Sealants
3M™ Fire Barrier Foam FIP 1-Step
(Foam-in-place Firestop)
Finally, a UL Listed alternative to mineral wool,
bricks and runny, ineffective foams.
•
•
•
•
P/N 74588, 12.85 fl oz *
P/N 74588N, Nozzle (2 pack)
*Includes 2 nozzles (P/N 74588N)
A smoke and firestopping foam for wall and floor penetrations.
Used in mechanical, electrical, data and plumbing applications.
Premium two-part, easy-to-handle formulation.
Expands during installation and bonds to concrete, metal, wood, plastic and cable jacketing.
Dries to a flexible solid.
This Foam Won’t Roam.
It’s like no firestop foam you’ve used before — it works. It’s not runny, so it stays in place and expands
at a controlled and consistent pace. Installs in vertical and horizontal applications without running down
the opening or sagging. Similar to many two-part epoxy sealants, but with just one step — saving you
trips up and down the ladder.
Items are non-stock. Please allow
1 to 2 weeks for delivery
(3M factory stock). For urgent
requirements, please call.
Key Features:
P/N 9572
HandyMax® HMS-G4C2
Manual Gun
• Firestop tested up to 2 hours in accordance with ASTM E 814 (UL 1479) and CAN/ULC S115.
• Meets the International Building Code for Passive Fire Protection.
• Expands up to 5X when dispensed. One cartridge FIP 1-Step equals up to 6 tubes 10.1 oz caulk.
• Intumescent. Expands in a fire.
• Expansive UL systems for blank openings, metal pipe, cables, cable trays, combos, insulated pipe.
• UL systems require no mineral wool.
• Remains pliable after installation for easy installation of new cables/conduit in existing opening.
• Excellent adhesion. Can be installed in wall or floor applications with no backing material.
• STC rating of 57 when tested in STC 57 rated wall assembly.
• Air leakage less than 1 CFM/Sq Ft.
• Shelf life is 12 months in original unopened containers from date of packaging.
Typical Applications:
P/N 9573
PowerMax® HPS-4C2
Battery-Powered Gun
• Conduit banks
• Cables
• Cable trays
• Combos
• Busways
• Metal pipes
• Plastic pipes
• Insulated pipes
• HVAC duct penetrations
• Blank openings in floors and walls
30
IMPORTANT:
Products do not achieve
ratings, systems do.
Consult your UL directory
for specific information
regarding your application.
See FIP 1-Step
in action! Scan
the QR Code to
go to the video.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.23
30
30.24
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Bulk Chemicals
Part #74240:
55 Gallon Drum
Part #74241:
30 Gallon Drum
Part #74243:
5 Gallon Pail
Part #74244:
1 Gallon Container
(Buy 4 x 1 Gal)
Aluminum Brite
TM
(Concentrated, deep cleaning metal cleaner)
A fast-acting, deep cleaning solution for removing dirt, oxide and carbon stains from aluminum,
stainless steel, copper, magnesium and other similar metals. Cleans and brightens.
Features:
• Concentrated
• Deep cleaning and fast acting
• Easy to use – requiring no scrubbing,
buffing or polishing
• Economical – saving time, money and labor
Applications:
• Truck Bodies • Wheels • Buses
• Aircraft • Equipment • Machinery
Instructions*:
Light Duty Application: Mix (1) part cleaner
with up to (10) parts water
Heavy Duty Carbon Stains: Mix (1) part
cleaner with (5) parts water
Big Job Truck Wash
TM
Part #74235:
55 Gallon Drum
Part #74236:
30 Gallon Drum
Part #74238:
5 Gallon Pail
Part #74239:
1 Gallon Container
(Buy 4 x 1 Gal)
Part #74250:
55 Gallon Drum
Part #74251:
30 Gallon Drum
Part #74253:
5 Gallon Pail
Part #74254:
1 Gallon Container
(Buy 4 x 1 Gal)
(Concentrated, water-based, biodegradable, manual or auto wash)
A highly concentrated liquid cleaning compound designed for autos, trucks, buses and
planes where minimum surface agitation is required. It's easy to use manually or in automatic
equipment, and it's economical.
Features:
• Super-concentrated
• Dissolves road film
• Biodegradable
• Manual or automatic washing
Applications:
• Autos • Trucks • Buses • Planes • Railroad Cars
• Vans • Trailers • Tractors • Box Cars
Instructions*:
Light Duty Application: Dilute (2-3) ounces per gallon of water
Heavy Duty Soils: Dilute (4-8) ounces per gallon of water
Automatic / Mechanical Washers: Dispense at a 1 to 50
dilution rate
Citrus Grease Digester
TM
(Unclogs, degreases, deodorizes)
Revitalizes sluggish disposal systems and quickly reduces buildup of grease and slime in
sewage treatment equipment without affecting bacterial activity. Effectively controls odor. Will
not harm metal pipes. Eliminates heat generation. Nonacid, noncaustic and noncorrosive.
Features:
• Unclogs, deodorizes and degreases
• Extremely effective in drains, grease traps,
septic systems, dry wells and cesspools
• Environmentally safe
• Natural citrus base
Instructions*:
Applications:
• Sewage Treatment Plants • Landfills
• Waste Disposal Facilities
• Maintenance of Drains • Garbage Areas
• Refuse Trucks and Cans
For more information,
see Technical Bulletin #30.028
Drain Cleaner: To open drains clogged by grease and slime, pour in 8 oz. (1/2 pint). Allow to stand for
1 hour. Flush with hot tap water. In garbage disposals, allow to stand 5-10 minutes. Flush with hot tap
water. CAUTION: Do not use in plastic pipes.
Drain Grease Trap Maintenance: Pour in a solution of 8 oz. per gallon of water. Allow to stand 1 hour.
Flush with hot tap water. CAUTION: Do not use in plastic pipes.
General Cleaning, Degreasing and Odor Control: Dilute (4) oz. to (1) gallon of warm water.
Not for use on synthetic or resilient tile floors.
Sewage Plants, Septic Tanks and Drainfields: Add (1) quart to (1,000) gallons of capacity or
dispense through a drip device as required for maximum odor control.
CAUTION: Contains powerful organic compounds and may damage some plastic or painted surfaces.
*NOTE: Always test product on an inconspicuous area before using. Since conditions of use are outside our control, we can assume no liability for results obtained or
damages incurred through the application of this product.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.25
30
Bulk Chemicals
Part #74350:
55 Gallon Drum
Part #74353:
5 Gallon Pail
Clear View
TM
**
(Concentrated, biodegradable, glass and hard surface cleaner)
Provides deep cleaning power for all glass and hard surface applications. A special blend of
detergents, drying accelerators and ammonia dissolve dirt, dust and fingerprints. Leaves a
gleaming, streak-free shine. Safe for most surfaces. Will not leave oily or soapy film. Repels dirt,
dust and fingerprints.
Features:
• Removes dirt, grease and fingerprints
• Fast-drying
• Non-streaking
• Non-abrasive
Applications:
• Glass • Mirror • Porcelain • Formica
• Stainless Steel • Aluminum • Chrome
• Tile • Painted Surfaces • Plastic
Instructions*:
Light Duty Application: Dilute with up to (2) parts water
Heavy Duty Soils: Use full strength
Part #74340:
55 Gallon Drum
Part #74341:
30 Gallon Drum
Part #74343:
5 Gallon Pail
Part #74344:
1 Gallon Container
(Buy 4 x 1 Gal)
**Also available in "Ready-to-Use"
pre-diluted formula (Part #74601).
(Packaged in 32 oz. bottle with trigger sprayer).
Coil and Filter Cleaner
(HVAC multi-purpose, coil and filter cleaner)
A non-caustic, non-acid cleaner designed to remove the build-up of dirt and grime on all HVAC
and refrigeration coils and filters. Also works well as a filter adhesive, providing a viscous, tacky
film to catch dirt, dust and pollen too small for retention by the filter.
Features:
• Cleans HVAC/refrigeration coils and filters
• No rinsing necessary
• Easy-to-use
• Non-flammable
Applications:
• Coils • Filters • Condensers
• Air Conditioning Systems
• Heating Units • Refrigeration Systems
Instructions*:
Light Duty Application: Dilute (1) part cleaner to (1-3) parts water
Permanent Type Filters: Dilute (1) part cleaner to (3) parts water and place filter in dip tank solution
As Filter Adhesive: Use full strength by spraying directly on the filter
Part #74245:
55 Gallon Drum
Part #74246:
30 Gallon Drum
Part #74248:
5 Gallon Pail
30
Part #74249:
1 Gallon Container
(Buy 4 x 1 Gal)
Diesel Fuel Additive **
(Injector cleaner, rust inhibitor, smoke reducer)
Cleans injectors, screens, fuel pumps and filters result in more even burning and easier starting.
Improves combustion by its catalytic action, resulting in more power and greater mileage. Improves
performance in all diesel engines and when used in diesel fuel storage tank, greater fuel stability
is achieved.
Features:
• Increases mileage
• Reduces "smoking"
• Improves performance
• Extends fuel life
• Reduces downtime
Instructions:
Applications:
• Diesel Trucks / Buses
• Bulk Fuel Storage Tanks
• Engines • Fuel Tanks
**Also available in "Ready-to-Use"
pre-diluted formula (Part #74604).
(Packaged in 32 oz. bottle with trigger sprayer).
Combine (1) quart to (100) gallons of diesel fuel. Add directly to fuel. Give special attention to the
crankcase oil in engines with heavy deposits of varnish, carbon or sludge. If large volumes of deposits
are released quickly, chang eoil and filters to rid the engine of these deposits.
*NOTE: Always test product on an inconspicuous area before using. Since conditions of use are outside our control, we can assume no liability for results obtained or
damages incurred through the application of this product.
30.26
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Bulk Chemicals
Part #74305:
55 Gallon Drum
Part #74306:
30 Gallon Drum
Part #74308:
5 Gallon Pail
Part #74309:
1 Gallon Container
(Buy 4 x 1 Gal)
Equipment Clean
TM
(Emulsifiable, solvent-based, engine/equipment cleaner/degreaser)
Unique, emulsifiable formulation instantly dissolves the toughest caked-on grease, dirt, oil and
wax and washes off with water. Exceptionally versatile, cleaning everything from small parts, to
engines, to concrete floors – and will not harm most painted surfaces. Easy to use and economical
– can be diluted with common petroleum solvents.
Features:
• Cleans on contact
• Heavy duty degreasing power
• Dilutes with petroleum solvents
• Emulsifiable
• Leaves no residue
Applications:
• Equipment • Machinery • Engines • Small Parts
• Bearings • Wheels • Chassis • Running Gear
• Concrete Floors • Transmissions • Fork Lifts
• Fifth Wheels • Parts Cleaners
Instructions*:
Dilute with up to (8) parts kerosene, diesel fuel, mineral spirits or naptha as per chart below.
Caution: If using with a pressure sprayer, Equipment Clean must be diluted with at least (8) parts solvent.
Insufficient dilution may cause spray hose to deteriorate and fail, causing possible injury or property damage.
Dilution Rates (1-Part Equipment Clean)
PARTS SOLVENT
PARTS SOLVENT
Equipment / Machinery .............................4 - 6
Engines – Normal .....................................4 - 6
Engines – Heavy Grease..........................1 - 2
Small Parts / Bearings ..............................4 - 6
Wheels......................................................6 - 8
Part #74200:
55 Gallon Drum
Part #74201:
30 Gallon Drum
Part #74203:
5 Gallon Pail
Part #74204:
1 Gallon Container
(Buy 4 x 1 Gal)
Chassis .....................................................6 - 8
Running Gears ........................................... 4
Cold Tank Degreaser .................................. 4
Concrete Floors .......................................... 3
Wax Coatings ............................................. 2
4-Way Plus **
Part #74200-74204
(Multi-purpose lube and penetrant with high dielectric strength)
An outstanding effective rust preventive and water displacing compound for ferrous and nonferrous substrate. The protective film left on the metal after evaporation of the solvent is ultra
thin and highly protective against corrosive effects of the elements.
Features:
• Long lasting
• Removable coating
• Corrosion prevention
• Protects from elements
• Water displacement
• Phosphate free
Applications:
• Rust preventative for metal parts in machine shops
• Tools • Equipment • Tractors • Bicycles
• Cranes • Vehicles • Electrical Systems
• Generators • Alternators • Starters
30
Instructions:
For Small Parts: Immerse parts into the compound for full strength for a few seconds. Remove and
allow to air dry until all the solvent is evaporated.
For Equipment: Brush, spray or simply apply with a cloth dampened with the chemicals. Allow to dry.
Removing: Use mineral spirits or similar solvent or alkaline cleaner (where applicable) to wash down
parts.
**Also available in "Ready-to-Use" pre-diluted formula (Part #74603).
(Packaged in a 32 oz. bottle with trigger sprayer).
*NOTE: Always test product on an inconspicuous area before using. Since conditions of use are outside our control, we can assume no liability for results obtained or
damages incurred through the application of this product.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.27
Bulk Chemicals
Part #74345:
55 Gallon Drum
Part #74346:
30 Gallon Drum
Part #74348:
5 Gallon Pail
Part #74349:
1 Gallon Container
(Buy 4 x 1 Gal)
Floor Glo™
(Transparent, high gloss durable floor finish)
A durable, long-lasting, high gloss floor finish that withstands the toughest traffic conditions. Its
transparent sheen will not darken or yellow and provides waterproof protection against damp
mopping and spray buffing. One gallon covers 1,500 to 2,000 square feet.
Features:
• Tough thermoplastic coating
• Scuff resistant
• Superb durability
• Withstands high traffic and
repeated detergent washings
Applications:
• All Types of Resilient Flooring
• Asphalt • Tile • Vinyl • Rubber
• Terrazzo • Linoleum • Masonry
• Varnished, Painted or Sealed Wood
Instructions:
Preparation: Strip other polishes from the floor using an abrasive pad and Red Lion Super Stripper
solution. Pick up with a wet vac, mop or autoscubber. Rinse the floor thoroughly (at least twice) with
clean water. Repeat the operation if all polish is not removed. Allow floor to dry.
Application: Using a clean synthetic mop, apply 3 coats of Floor Glo allowing a minimum of 30
minutes between coats. Additional coats of finish may be applied, provided adequate dry time (at least
one hour) is allowed between coats. Temperature, humidity and air movement affect curing time.
Burnishing: The thermoplastic properties of the floor finish are enhanced by the heat of high speed
burnishing equipment (1500-2000 RPM) producing the desirable "ultra wet look." Burnish with any
high speed machine using procedure as outline by the machine manufacturer in conjunction with the
proper high speed burnishing pad.
Maintenance: The floor may be maintained by damp mopping with a free rinsing neutral detergent
followed by high speed burnishing or high speed spray buffing with a suitable spray buffing compound
or mop-on restorer. Additional coat may be applied after thoroughly scrubbing floors. If stripping
becomes necessary, use Red Lion Super Stripper. If floor is exposed to heavy traffic of sand or other
abrasive soils, frequent dust mopping is recommended. Do not pour unused finish back into
original container or contaminate with other finishes.
Part #74215:
55 Gallon Drum
Part #74216:
30 Gallon Drum
Part #74218:
5 Gallon Pail
Part #74219:
1 Gallon Container
(Buy 4 x 1 Gal)
30
H.D. Citrus Cleaner/Degreaser™ **
(Concentrated, citrus-based, biodegradable cleaner/degreaser)
A highly concentrated cleaner and degreaser. This powerful water soluble cleaner derives its
strength from d-limonene, a natural citrus solvent. Instantly dissolves greasy, oil soils from
virtually any surface and it deodorizes while it cleans. Extremely concentrated – can be diluted
up to 100 to 1.
Features:
• Highly concentrated
• Extremely powerful
• Natural citrus extract
• Instantly dissolves greasy, oil soils
• Biodegradable
Applications:
• Porcelain • Formica • Tiles • Enamel Surfaces
• Tools • Equipment • Oil and Tar Stains
• Vinyl Tops • Floor Mats • Tubs • Sinks
• Appliances • Printing Presses • White Wall Tires
Instructions*:
Spray with hand sprayer or low or high pressure equipment, Steam, mop, brush or wipe on any water
safe surface. Wipe or rinse off with clear water.
Lightly Soiled: 1 to 4 oz. per gallon
Medium Soiled: 4 to 10 oz. per gallon
**Also available in "Ready-to-Use" pre-diluted formula (Part #74600).
(Packaged in a 32 oz. bottle with trigger sprayer).
*NOTE: Always test product on an inconspicuous area before using. Since conditions of use are outside our control, we can assume no liability for results obtained or
damages incurred through the application of this product.
30.28
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Bulk Chemicals
Lift-Out Lift Station Degreaser
TM
Part #74280:
55 Gallon Drum
Part #74281:
30 Gallon Drum
Part #74283:
5 Gallon Pail
Part #74284:
1 Gallon Container
(Buy 4 x 1 Gal)
(Water insoluble, grease dissolving, biodegradable)
This powerful and efficient emulsifying agent liquifies animal fats and garbage grease in lift
stations, greasetraps and drain lines for maximum performance. It maintains facilities in top
operating condition while eliminating odors, overflowing and unsanitary conditions resulting
from poor draining caused by slime and grease. Harmless to most plumbing.
Features:
• Liquifies
• Deodorizes
• Degreases
• Extremely effective in drains, grease traps,
septic systems, dry wells and cesspools
Applications:
• Lift Stations • Sewage Treatment Plants
• Landfills • Waste Disposal Facilities
• Drain Maintenance
• Refuse Trucks and Cans
• Garbage Areas
Instructions*:
Lift Stations: To add a one inch cap on liftstation, pour in four times the diameter (in feet) as the
number of gallons. For rectangular lift stations, multiply the length times the width (in feet) by .625.
Use this as the number of gallons.
Drain Cleaner: To open drains clogged by grease and slime, pour in 8 oz. (1/2 pint). Allow to stand
for 1 hour. Flush with hot tap water. In garbage disposals, allow to stand 5-10 minutes. Flush with hot
tap water. Do not use in plastic pipes.
Drain and Grease Trap Maintenance: Pour in a solution of 8 oz. per gallon of water. Allow to stand
1 hour. Flush with hot tap water.
Sewage Plants, Septic Tanks, Drainfields, etc.: Add (1) quart of product to (1000) gallons of
capacity or dispense through a drip device as required for maximum odor control.
N-Zyme Drain Maintenance
TM
Part #74285:
55 Gallon Drum
Part #74286:
30 Gallon Drum
Part #74288:
5 Gallon Pail
Part #74289:
1 Gallon Container
(Buy 4 x 1 Gal)
(Liquid waste digester)
This liquid waste digester prevents blocked drains by biologically degrading organic wastes,
grease, fats, oil cellulose, protein and starch residues. Contains no acids or caustics to
damage drains or interfere with septic tanks, ponds and lagoons. The bacterial culture
establishes colonies which remain in the system and reactivate each time waste is introduced.
Features:
• Non-toxic
• Non-corrosive
• No fumes
• Extremely concentrated
• Excellent preventitive maintenance tool
Applications:
• Sinks • Drains • Grease Traps
• Interceptors • Drain Fields
• Septic Tanks • Sewers
Instructions:
Stir before initial use. For best results, treat waste systems at night or during the lowest use period.
Just before adding, flush sinks, drains or other areas of entry with warm water to remove any residue,
disinfectants, bleach or other harsh chemicals that may harm bacterial cultures.
Grease Traps: When possible, clean out grease trap prior to beginning of treatment. Add 1 to 3 oz.
per cubic foot of trap capacity. Use drain close to trap. To maintain, add 2 to 3 oz. each night.
Drain Lines: Use 1 to 3 oz. per drain, diluted with warm water. Pour into sinks, floor drains, garbage
disposals, toilets and urinals once a week.
Septic Tanks, Dump Stations: For slow systems, use 1 pint (16 oz.) for each 500 gallons of capacity.
Mix into 2 gallons of warm water and flush through toilet furthest from tank. To maintain, apply 1 quart
per month or as needed.
Sludge Lagoons and Ponds: During first 3 to 7 days, add 1/2 gallon daily for each million gallons of
wastewater. To maintain, add 1 quart weekly at inlet ditch.
Setting Tanks: Add 1 quart for each 1,000 cu. ft. (8,000 gals.) capacity. Add weekly for 4 weeks.
To maintain, add 1 quart per 1,000 cu. ft. per month.
Recreational Vehicles, Boats, Portable Toilets: Add 8 oz. for each 5 gallons of holding tank capacity.
NOTE: Disinfectants, chlorinated products and extra-hot water (over 160oF) will kill off some of the live bacteria. Always store below 120oF.
Avoid storing in car trunk in summer time.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.29
30
Bulk Chemicals
Part #74360:
55 Gallon Drum
Part #74361:
30 Gallon Drum
Part #74363:
5 Gallon Pail
Part #74364:
1 Gallon Container
(Buy 4 x 1 Gal)
Odor Eliminator
TM
**
(Encapsulates & destroys toughest odors, biodegradable, lemon-lime scent)
A concentrated product, scientifically formulated to eliminate any and all odors safely and
effectively. Odor Eliminator does not "mask" odors, it neutralizes them by chemically bonding
with the odor carrying molecules and encapsulating them, thereby stopping odor formation.
It is non-flammable, non-staining and non-corrosive.
Features:
• Chemically "neutralizes" and eliminates odors
• Does not mask odors
• Use as an air or surface spray
• Refreshing lemon scent
• Non-flammable
Applications:
All Airborne Odors in:
• Rendering Plants • Slaughter Houses • Zoos • Kennels • Public Rest Rooms
• Transportation Industry • Locker Rooms • Garbage Areas • Sewage Areas
• Smoke Filled Rooms • Mortuaries • Hotels • Air Conditioning Filters
Instructions:
Use full strength or dilute with water as an air or surface spray.
**Also available in "Ready-to-Use" pre-diluted formula (Part #74602).
(Packaged in a 32 oz. bottle with trigger sprayer).
Part #74270:
55 Gallon Drum
Part #74271:
30 Gallon Drum
Part #74273:
5 Gallon Pail
Part #74274:
1 Gallon Container
(Buy 4 x 1 Gal)
30
Odor Eliminator SC
TM
(Super concentrated Odor Eliminator formula)
A super-concentrated product, scientifically formulated to eliminate any and all odors safely
and effectively. It does not "mask" odors, it neutralizes them by chemically bonding with the
odor carrying molecules and encapsulating them, thereby stopping the odor formation. It's nonflammable, non-staining and non-corrosive.
Features:
• Super-concentrated formula
• Chemically "neutralizes" and eliminates odors
• Does not mask odors
• Use as an air or surface spray
• Refreshing lemon scent
• Non-flammable
Applications:
All Airborne Odors in:
• Rendering Plants • Slaughter Houses • Zoos • Kennels • Public Rest Rooms
• Transportation Industry • Locker Rooms • Garbage Areas • Sewage Areas
• Smoke Filled Rooms • Mortuaries • Hotels • Air Conditioning Filters
Instructions:
Dilute (1) part Odor Eliminator SC to (3) parts water. This provides concentration equal to standard
Odor Eliminator product. May be diluted further for lighter duty applications.
*NOTE: Contains powerful organic compounds and may damage some plastic or painted surfaces. Always test product on an inconspicuous area before using. Since
conditions of use are outside our control, we can assume no liability for results obtained or damages incurred through the application of this product.
30.30
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Bulk Chemicals
Part #74230 & 74225:
55 Gallon Drum
Part #74231 & 74226:
30 Gallon Drum
Part #74233 & 74228:
5 Gallon Pail
Part #74234 & 74229:
1 Gallon Container
(Buy 4 x 1 Gal)
Pleasant Scent™
(Chemically destroys toughest odors)
Part #74230-74234 – Lemon-Lime Scent
Part #74225-74229 – Green Apple Scent
A highly refined blend of chemicals designed to destroy odors of putrefaction, defecation,
regurgitation, urination and many other malodors. It is easy to apply with a trigger sprayer or
fogging unit and is biodegradable, phosphate free and nonflammable.
Features:
• Chemically destroys the toughest malodors
• Does not mask odors
• Easy to use as an air or surface spray
• Biodegradable
Applications:
• Hospitals /Laboratories • Mortuaries • Motels • Factories
• Rest Rooms • Kennels • Airplanes • Etc.
Instructions:
Use full strength or dilute with water. Dilutes up to 10:1.
Part #74275:
55 Gallon Drum
Part #74276:
30 Gallon Drum
Part #74278:
5 Gallon Pail
Part #74279:
1 Gallon Container
(Buy 4 x 1 Gal)
Safety Solv 2000
TM
(Non-chlorinated, fast acting, high flash point cleaner/degreaser)
A fast acting, non-corrosive cleaning and degreasing solvent for removing dirt, grease, oil, lubricants,
ink, adhesive, tar, soot, wax and many other contaminants from mechanical and electrical equipment.
It has a flash point of 142oF and a mild solvent odor.
Features:
• Superior degreasing properties
• Equipment / machinery
• Fast-acting
(142oF)
• Non-corrosive
• Mild odor
•
High
fl
ash
point
Applications:
• Metal • Plastics • Fiberglass • Motors • Pressure Tanks • Rubber • Molds
• Paint Masks • Printing Equipment • Meters • Pre-Welding Applications
Instructions:
General Cleaning/Degreasing: Apply directly to material using brush, dip, spray or wiping action.
Wipe dry or blow with compressed air.
Motors: Turn power off and remove all loose material, lint and dust by air blowing motor. Replace all
worn and arcing brushes. Resurface commutator if arcing continues. Spray into motor with a heavy
stream. Blow motor with air until dry. Relubricate before using.
Disassembled Equipment: Immerse parts in solvent for 5-10 minutes. Dipping, ultrasonics or any
method of agitation will hasten cleaning action. Wipe dry or blow dry with compressed air upon removal.
Part #74257:
55 Gallon Drum
Part #74256:
30 Gallon Drum
Brake Clean
(Contains no chlorinated solvents, hexane free cleaner/degreaser)
Specially formulated to work quickly and effectively to remove brake fluid, grease, dirt and
other contaminants from brake linings, disc brake pads, brake drums, springs, wheel
cylinders, etc. Stops disc brake squeal, leaves no residue and is an excellent cleaner for
other dirty, greasy parts.
30
Features:
• Cleans and degreases all brake parts and instantly removes dirt, grease and brake fluid
• Improves brake performance
Applications:
• For use on brake linings, disc brake pads, brake drums, springs, wheel
cylinders and other brake parts
Instructions:
Spray brake parts liberally and allow to run off. Allow to air dry or use a soft wipe. Repeat if
necessary. Do not spray on hot or warm surfaces. Protect rubber and plastic parts from spray.
*NOTE: Always test product on an inconspicuous area before using. Since conditions of use are outside our control, we can assume no liability for
results obtained or damages incurred through the application of this product.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.31
Bulk Chemicals
Part #74310:
55 Gallon Drum
Part #74311:
30 Gallon Drum
Part #74313:
5 Gallon Pail
Part #74314:
1 Gallon Container
(Buy 4 x 1 Gal)
Steam Clean
TM
(All purpose, deep cleaning, free-rinsing)
A special formulation of surfactants and cleaners provide the most effective and versatile steam
cleaning product available. Use for cleaning and degreasing painted surfaces, metals, concrete,
chrome, rubber and glass. Steam solubilizes, emulsifies and penetrates grease, dirt and oil, so it
can be easily flushed off the surface being cleaned. This special formula prevents clogging of coils
and is very effective on aluminum, steel and other metal surfaces. Leaves no scale or residue.
Features:
• Deep cleaning formula
• Free rinsing
• Controlled foam
• Biodegradable
• Non-flammable
Applications:
• Engines • Walls • Floors
• Drive Line Components
• Chains • Cables
Instructions:
Always follow the manufacturer's instructions for the steam cleaning equipment. For steam cleaners
that feed directly into the coils, use (1) quart of Steam Clean per (20) gallons of water. Steam cleaners
that premix cleaner with water before going through the coils use (1) gallon of Steam Clean for (20)
gallons of water.
Proper flow is determined by the sudsing action at the nozzle. If too much cleaner is added to the
solution, adjust the flow to the point where sudsing just begins at the spray nozzle. Although normally
used in steam cleaning machines, Steam Clean may also be used as a soak solution. Use 6-10 oz.
per gallon of warm or hot water.
NOTE: Steam Clean may be used on glass and aluminum. However, it should not be allowed to dry directly on these surfaces.
Rinse thoroughly with clear water immediately after cleaning.
Part #74315:
55 Gallon Drum
Part #74316:
30 Gallon Drum
Part #74318:
5 Gallon Pail
Part #74319:
1 Gallon Container
(Buy 4 x 1 Gal)
30
Steam Clean HD™
(All purpose, deep cleaning, free-rinsing)
An extremely powerful steam cleaner, containing special cleaners and surfactants that plate out
on the surface to remove dirt and grease. Powerful enough to clean 5th wheels. A concentrated
emulsifier dissolves greasy, oily and waxy soils and deodorizes as it cleans. Through emulsification,
soils are removed from surfaces and suspended through the cleaning solution. Redeposition of
soils is minimized, enabling quick and complete rinsing. For use on all surfaces.
Features:
• Extremely powerful formula
• Free rinsing
• Controlled foam
• Biodegradable
• Non-flammable
Applications:
• Engines • Walls • Floors
• Drive Line Components
• Chains • Cables
Instructions:
This is a concentrate and must be diluted prior to use. Dilution ratios will vary depending upon the
degree and nature of the soil and should be adjusted as experience dictates. For trucks, buses or
airplanes, use (1) part concentrate (20-40) parts water. The solution may be applied by brushing,
wiping or spraying. After cleaning, rinse thoroughly with clear water. Do not allow solution to dry on
surface.
NOTE: Steam Clean HD should not be used on aluminum, glass or painted surfaces.
All surfaces should be rinsed immediately after use with clear water.
*NOTE: Always test product on an inconspicuous area before using. Since conditions of use are outside our control, we can assume no liability for results obtained or
damages incurred through the application of this product.
30.32
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Bulk Chemicals
Part #74300:
55 Gallon Drum
Part #74301:
30 Gallon Drum
Part #74303:
5 Gallon Pail
Part #74304:
1 Gallon Container
(Buy 4 x 1 Gal)
Super Clean
TM
(Highly alkaline, water soluble concentrated solvent)
It's unique formulation provides the ultimate versatility in an industrial cleaner. Use on metal,
plastic, rubber, concrete, iron, steel and aluminum (except anodized aluminum). Emulsifies
dirt, grease, oil, wax, creosote and many other stubborn stains. There's no need for scrubbing
because Super Clean's emulsifying action floats dirt away. Just rinse with clear water to leave
a bright clean surface with no oily residue.
Features:
• Heavy duty degreaser
• Versatile • Economical
• Free-rinsing • Non-flammable
• Biodegradable
Applications:
• Machinery • Equipment
• Concrete • Walls • Floors
• Filters • Ventilator Screens
• Any surface where a
fireproof cleaner is needed
Instructions*:
Dilute with up to (30) parts water as per dilution chart.
Dilution Rates (1-Part Super Clean)
PARTS
WATER
Machinery, Equipment, Metal Parts, Concrete Floors ............5
General Cleaning of Floors, Asphalt, Linoleum,
Vinyl, Composition, Wood, Terrazzo, etc. ............................20
General Light Cleaning of Walls, Woodwork, etc. .................30
Removing Oil, Grease, Carbon or Common Soil in
General Cleaning, Hoods, Flues, Vents, etc.........................5
Splash Boards: Aluminum, Chrome, Stainless .......................6
Conveyors, Stoves, Stove Parts, Ovens, Grills, Fat Fryers ....2
Walls ......................................................................................12
Floors, Floor Boards ...............................................................8
Caution: Super Clean contains solvents which may cause etching of glass and discoloration of anodized aluminum.
In case of contact, rinse immediately with water.
Super Gloss Wash-N-Wax
TM
Part #74220PF:
55 Gallon Drum
Part #74221PF:
30 Gallon Drum
Part #74223PF:
5 Gallon Pail
Part #74224PF:
1 Gallon Can
Part #74355:
55 Gallon Drum
Part #74356:
30 Gallon Drum
Part #74358:
5 Gallon Pail
Part #74359:
1 Gallon Container
(Buy 4 x 1)
(High-foaming, concentrated, water-based, biodegradable, leaves glossy shine)
A super-concentrated, high-foaming, biodegradable detergent specially formulated for auto,
truck, van, motor home and boat washing. It dissolves dirt and grime, leaving a superior high
gloss, spotless appearance. The powerful emulsifiers of Super-Gloss Wash-N-Wax actually
lift embedded dirt, grime, bug and tar stains off surfaces. The high-foaming action keeps it in
suspension for easy rinsing.
Applications:
• Autos • Trucks • Vans
• Motor Homes • Boats
Features:
• Highly concentrated
• Leaves a high gloss finish
• Will not streak or spot
• Biodegradable
Super Stripper
Instructions:
Pour (1 to 3) oz. of Super Gloss in a bucket for each
gallon of warm water.
TM
30
(Concentrated, non-ammoniated floor finish remover)
This concentrated formula safely and easily removes all types of waxes, finishes and soils.
Special wetting agents help to emulsify dirt for easy rinsing. Extremely effective on multiple
coats of waxes, polymers and acrylic coatings on all types of floors.
Features:
• Concentrated
• Fast-acting
• Removes all types of waxes,
finishes and soils
Applications:
• Tile • Terrazzo • Concrete • Marble • Asphalt
• Vinyl • Linoleum • Composition
Instructions*:
Mix (1) part Super Stripper to (15) parts water. If wax or finish
is especially heavy or old, increase recommended amount to
fit the type and amount of soil to be removed.
*NOTE: Always test product on an inconspicuous area before using. Since conditions of use are outside our control, we can assume no liability for results obtained
or damages incurred through the application of this product.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.33
Bulk Chemicals
Part #74320:
55 Gallon Drum
Synthetic / Soluble Cutting Fluid
(Concentrated water soluble lubricant)
Part #74321:
30 Gallon Drum
A concentrated synthetic coolant for metal working applications. Can be used "as is" or diluted
with up to 40 parts water.
Part #74323:
5 Gallon Pail
Features:
• Clear concentrated water soluble lubricant
• Prevents corrosion
• Use for machining, cutting and grinding of ferrous and non-ferrous metals
Part #74324:
1 Gallon Container
(Buy 4 x 1 Gal)
Applications:
Effective and suitable for use in working:
• Carbon Steel • Stainless Steel • Vanadium • Chrome
• Molybdenum • Nitralloy • Titanium • Bronze • Copper
• Boron Carbide and many other specialty alloys
Instructions*:
May be used with or without dilution depending upon the job requirements. Dilutes clear in all
proportions for complete job visibility. It is suggested that more difficult job trials be made with fluid full
strength. If the results are satisfactory, further dilution up to 40 parts water to 1 part product can be
tested to determine the most economical dilution.
Part #74335:
55 Gallon Drum
Part #74336:
30 Gallon Drum
Part #74338:
5 Gallon Pail
Part #74339:
1 Gallon Container
(Buy 4 x 1 Gal)
X-tra Clean NB
TM
(Concentrated, all purpose water soluble cleaner/degreaser)
This highly concentrated non-butyl formulation of high grade synthetic surfactants yields the
ultimate in cleaning performance. It is free rinsing and works equally well in hot, cold, hard or
soft waters. It penetrates, loosens and emulsifies all types of oil, grease and soil – leaving an
exceptionally clean surface. Safe on most every water washable surface.
Features:
• Highly concentrated • Heavy duty • Water soluble • Non-flammable • Biodegradable
Applications:
• Basins • Bilges • Concrete • Dies • Equipment • Fans • Floors • Hoods • Machinery
• Metal • Plastic • Porcelain • Rubber • Sinks • Steel • Sumps • Terrazzo • Toilets
• Tooling • Vinyl Upholstery • Vitreous Ware • Walls • Wood
Instructions*:
Apply manually or with sprayer. Allow to work
for a few minutes, then wipe, mop or rinse
off. See dilution chart.
30
Steam Cleaning: Dilute (4-14) oz. cleaner
with (1) gallon of water. Adjust solution
according to desired results.
Dilution Rates (1-Part X-tra Clean NB)
PARTS
WATER
Degreasing ............................................................10
Heavy General Cleaning .......................................20
Light General Cleaning ..........................................60
Deodorizing ...........................................................60
Wax and Finish ......................................................10
Adjust dilutions according to type and amount of soil.
*NOTE: Always test product on an inconspicuous area before using. Since conditions of use are outside our control, we can assume no liability for results obtained
or damages incurred through the application of this product.
30.34
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Bulk Chemicals
Handles Cleaning
and Maintenance
in a Brand New Way!
•
•
•
•
•
•
•
•
•
Super Concentrated Chemical Cartridges ~ Dilutes 100 to 1
Strong, Fast-Acting Formulas ~ Provide Exceptional Performance
Easy-to-Use ~ No Complicated Mixing Equipment Necessary
Saves Space ~ Hundreds of Cartridges Fit on a Small Storage Shelf
Less Expensive ~ QX1 Cartridges Weight 1/50 of Ready-to-Use Products,
Dramatically Reducing Shipping Costs
Environmentally Friendly ~ Bottles and Sprayers are Reusable and Refillable
Safer ~ No Contact with Concentrated Chemicals
Color Coded Labels ~ Bottles and Cartridges are Color-Coded for Instant Recognition
Meets All Safety Requirements ~ OSHA and EPA Compliant Prelabeled Bottles
...
Easy as 1, 2, 3!
1. FILL Bottle With Water
2. INSERT QX1 Cartridge
3. ATTACH Trigger Sprayer
1
2
3
30
FILL WITH WATER
INSERT CARTRIDGE
ATTACH TRIGGER SPRAYER TO BOTTLE
NOTE: Bottle, Cartridge and Sprayer are proprietary designs and cannot be used with other components.
They must be used with the QX-1 System to work properly.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.35
Bulk Chemicals
QX1 Glass Cleaner with Anti-Stat
(For glass, plastic and CRT screens)
Part #74710 – .33 fl. oz.
cartridge
A specially formulated glass, plastic and CRT cleaner designed for use on glass, Lexan®, Lucite®,
mirrors, menu boards and other surfaces not harmed by water. This fresh blue formula utilizes
a special combination of soil-suspending detergents, and wetting agents to quickly remove soil
smudges, grease and finger prints without streaking. Quickly cleans and shines surfaces. Antistatic to repel airborne dirt.
Features:
• Safe on all thermoplastics
• Safe on anti-glare window coverings
• Streak-free, anti-static formula
*Empty Bottle:
Part #74710B
*Trigger Sprayer:
Part #1815
2. INSERT
CARTRIDGE
INTO
BOTTLE
NECK
Applications:
• Glass
• Mirrors
• Appliances
• Lexan®
• Lucite®
• Plexiglass
• Computer Monitors
• Other hard surfaces
3. ATTACH
SPRAYER
TO BOTTLE
AND
SHAKE
GENTLY
1. FILL TO
LINE WITH
WATER
Directions:
Insert one (1) cartridge with fresh clean water in the 32 oz. plastic bottle. Using a trigger
sprayer P/N 1815, apply directly to surface. Hold 6-8 inches from surface and spray lightly.
Wipe dry with lint-free towel or cloth. When cleaning computer screens, do not spray directly
on equipment, spray on wiping cloth and then clean screen.
*Bottle and Trigger designs are proprietary and must be used for the QX-1 System to work properly.
30
30.36
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Bulk Chemicals
QX1 Multi-Purpose Cleaner
Part #74711 – .33 fl. oz.
cartridge
(Powerful spray and wipe cleaner/degreaser)
Combines powerful grease cutting and cleaning agents to eliminate problem soils and stains.
Removes grease, grime, oil and dirt buildup from work stations, table tops, countertops, walls,
etc. Leaves surfaces squeaky clean and residue free.
Features:
• Concentrated spray and wipe formula
• Removes soil and ink from non-porous surfaces
• Residue-free
• Heavy duty grease cutting
• Non-flammable • Biodegradable
• Pleasant fragrance
*Empty Bottle:
Part #74711B
*Trigger Sprayer:
Part #1815
Applications:
• Schools
• Universities
• Child Care/Day Care
• Hospitals
• Institutions
• Nursing Homes
• Prisons
• Offices
• Gas Stations
• Restaurants
• Manufacturing Facilities
• Motel/Hotels
2. INSERT
CARTRIDGE
INTO
BOTTLE
NECK
3. ATTACH
SPRAYER
TO BOTTLE
AND
SHAKE
GENTLY
1. FILL TO
LINE WITH
WATER
Directions:
Hold container with trigger sprayer attached 6-8 inches from surface and lightly spray surface.
Wipe dry with lint-free towel or cloth.
*Bottle and Trigger designs are proprietary and must be used for the QX-1 System to work properly.
30
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.37
Bulk Chemicals
QX1 Disinfectant Cleaner
Part #74712 – .33 fl. oz.
cartridge
(No-rinse cleaner and disinfectant)
An extremely effective cleaner, deodorizer and disinfectant specifically designed for use in hospitals,
nursing homes, schools, hotels and food service establishments. Provides broad spectrum
effectiveness against gram-positive and gram-negative bacteria including Staphylococcus Aureas
(Methicilin Resistant), viruses (including HIV-1 the AIDS virus) and pathogenic fungi including T.
mentagrophytes (the athlete's foot fungus) in the daily struggle to control cross-contamination
and reduce the spread of infection.
Applications:
• Schools
• Universities
• Child Care/Day Care
• Hospitals
• Institutions
• Nursing Homes
Features:
• One-step cleaner / disinfectant
• Kills VRE, MRSA and HIV-1 virus
• Concentrated
• Cleans tough soils
• Fresh pleasant fragrance
*Empty Bottle:
Part #74712B
*Trigger Sprayer:
Part #1815
•
•
•
•
•
•
Prisons
Offices
Gas Stations
Manufacturing Facilities
Motels and Hotels
Restaurants
Directions:
Insert one (1) cartridge with fresh clean water in the 32 oz. plastic bottle. Using a trigger
sprayer P/N 1815, apply directly to surface. Hold container with trigger sprayer attached 6-8
inches from surface and lightly spray surface. Treated surface must remain wet for 10 minutes.
Wipe dry with with lint-free towel or cloth.
QX1 Odor Eliminator
(Encapsulates and destroys toughest odors)
Part #74713 – .33 fl. oz.
cartridge
Our concentrated liquid malodor counteractant eliminates odors, leaving behind a fresh,
pleasant scent. This product has no color dies and may be utilized on a variety of surfaces
such as fabrics, carpets, upholstery, waste receptacle interiors, toilets and urinals.
Features:
• Counteracts the most pungent odors
• Will not harm most fabrics
• Atomize or apply directly to odor source
• Eliminates cigarette and other smoke odors fast
30
*Empty Bottle:
Part #74713B
*Trigger Sprayer:
Part #1815
• Institutions
• Waste Cans
• Drains
Directions:
Insert one (1) cartridge with fresh clean water in the 32 oz. plastic bottle. Using a trigger
sprayer P/N 1815, apply directly to surface. Hold container with trigger sprayer attached
6-8 inches from surface and lightly spray surface. Wipe dry with with lint-free towel or cloth.
For Counteracting Airborne Odors: Using a trigger sprayer, discharge into the air an
appropriate amount of formula allowing 5 to 20 seconds for the fresh scent to counteract
unwanted odors.
For Fabric Treatment: Discharge an appropriate amount of product to fabric, upholstery,
curtains, etc. Hold sprayer approx. 10 to 15 inches from surface. Apply product evenly to
affected areas. Always test on inconspicuous area fi rst.
Guest Accommodations: Apply proper amount of product approximately 5 inches above
carpet level to entire perimeter of room or until odor is eliminated.
* Bottle and Trigger designs are
proprietary and must be used for
the QX-1 System to work properly.
30.38
Applications:
• Toilets and Urinals
• Carpets
• HVAC Ducts
• Fabrics
2. INSERT
CARTRIDGE
INTO
BOTTLE
NECK
3. ATTACH
SPRAYER
TO BOTTLE
AND
SHAKE
GENTLY
1. FILL TO
LINE WITH
WATER
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Cleaners and Degreasers
Foaming Coil Cleaner
Part #74268 – 18 oz.
(HVAC multi-purpose equipment maintenance)
The no rinse formula reaches all areas of coils and the inverted spray allows for easy access to all areas
of unit.
Features:
• Thick foam lifts out and holds dirt and grime in suspension
until it is rinsed or condensation washes away the dirt and soil
• Pleasant scent
• For indoor and outdoor use
• Non-caustic and non-acid formula make for safe use
• Saves time and labor
Applications:
• Hotels
• Industrial plants
• Automotive
• Hospitals
• Roof top units
• Window units
Coil and Filter Cleaner
Part #74165 – 17 oz.
(HVAC multi-purpose equipment maintenance)
A non-caustic, non-acid cleaner designed to remove a build-up of dirt and grime on coils and
filters. Also works well as a filter adhesive, providing a viscous tacky maze of lattice work to catch
dirt, dust or pollen too small for retention by the filter.
Features:
• Removes dirt and grime on coils and filters
• No rinsing
• Non-flammable
• No corrosive residue
Applications:
• Can be used to renovate all types of coils, filters and condensers used in heating plants,
air conditioning systems, refrigeration plants and other heat exchange equipment.
Brake Clean N.C.
Part #74147 – 12.25 oz.
(Non-chlorinated cleaner and degreaser)
Specially formulated to work quickly and effectively to remove brake fluid, grease, dirt and other contaminants
from brake linings, disc brake pads, brake drums, springs, wheel cylinders and other brake parts. An excellent
cleaner for other dirty, greasy parts.
Features:
• Cleans and degreases all brake parts
• Instantly removes dirt, grease and brake fluid
• Improves brake performance
• Stops disc brake squeal
• Leaves no reside
Choke and Carb Cleaner
Applications:
• For use on brake linings, disc brake
pads, brake drums, springs, wheel
cylinders and other brake parts
30
Part #74115 – 14.75 oz.
(Fast-drying carburetor cleaner)
Specifically formulated to clean, lubricate and protect chokes, carburetors, PCV systems, manifold heat
valves, linkages and butterfly valves.
Features:
• Removes carbon, dirt, gum and varnish deposits
• Cleans, frees and renews automatic chokes,
carburetors, linkages, PCV valves,
manifold heat controls
• Dries fast, leaving no oily film
050114
Applications:
• For use on chokes, carburetors,
PCV systems, manifold heat valves,
linkages and butterfly valves
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.39
Cleaners and Degreasers
Battery Acid Cleaner/Neutralizer Wipes
P/N 74098 – 30 Wipes
(Heavy duty color-changing treated sheet for lead acid batteries)
Wipe the surface, removing deposits. The blue wipe will turn pink in the presence of the acidic
corrosion. Continue scrubbing the area until the wipe turns back to its original blue color. This
will indicate that the acid has been neutralized.
Features:
• Formulated to clean, remove corrosion, and neutralize battery acid
• If heavily corroded - after using wipes, a light scrubbing with a plastic bristle brush will
remove corrosion with no messy foam
• Contains acid neutralizing agents
• Color changing system lets you know when the acid is neutralized
Applications:
• Car & Truck Batteries
• Golf Cart Batteries
• Terminals
• Connectors
• Trays
Battery Protector & Cleaner
Part #74106 – 15 oz.
(Protective coating for batteries and battery terminals)
Excellent for use on batteries, terminals, cables, brackets, and housings. It is great for vehicle
fleets, golf carts, airplanes, boats, tractors, forklifts, construction equipment, floor scrubbers,
and more. This advanced formulation serves four applications in a single product! It cleans,
detects acid, neutralizes acid, and protects against corrosion.
NOTE: Do not allow this can to come into contact with battery cables or terminals, electrical wiring or other electrical components.
This can will conduct electricity and may cause an electrical spark resulting in serious injury from can rupture, flash fire or electrical shock.
Features:
• Prevents terminal corrosion
• Assures continued high-voltage output
• Prolongs battery life
Applications:
• Battery Terminals • Cable Connectors
• Casings • Frames • Housings
30
Insta-Shine Truck/Bus Protectant
Part #74169 – 16 oz.
(Fast polish and shine for painted/chrome surfaces)
Instantly cleans, polishes and protects painted surfaces, chrome, fiberglass and plastic.
It cuts through grease, bugs, tar and road film without water, leaving a durable, water-repellent
protective finish. Produces a professional shine on trucks, buses, autos, vans, boats, etc.
Features:
• Cleans, polishes and protects
• For use on exterior and interior surfaces
• Simple "spray and wipe" application
• Leaves a high gloss water repellent finish
30.40
Applications:
• Produces a professional shine on
trucks, buses, autos, vans, boats, etc.
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Cleaners and Degreasers
A/C Flush
(For use in flush guns)
Part #74382 – 1 Quart / 946 ml
Part #74383 – 1 Gallon / 3.78 L
Red Lion™ A/C Flush Solution is an excellent tool for retrofitting R12 systems to R134a as
mineral oil will be removed from components being flushed. For best results, use with
A/C Flush Gun (P/N 78047).
Features:
• Simple to use Premium Solvent-Based Solution
• Compatible with R-12, R-134a & R-22 Systems
• Removes debris and sludge from A/C components
• Evaporates quickly and leaves no residue
A/C Flush (Non-Flammable)
(For use in flush machines and flush guns)
Part #74384 – 1 Quart / 946 ml
Part #74385 – 1 Gallon / 3.78 L
Red Lion™ Non-Flammable A/C Flush is a premium solvent-based flushing agent for use in
closed loop flushing machines and pressurized flush guns for mobile A/C systems. It is an excellent
replacement for R141b refrigerant when used to clean and degrease mobile A/C systems and
components. Non-flammable A/C Flush is an excellent product to use during the retrofit process
from R12 to R134a and for repair of R134a systems.
Features:
• Simple To Use Premium Non-Ozone Depleting Solution
• Compatible with R-12, R-134a & R-22 Systems
• Removes debris and sludge from A/C components
30
Club Clean
P/N 74199 – 3 oz.
(Foaming golf equipment cleaner)
Club Clean is a “technologically advanced” formula that safely and effectively cleans all types
of golf equipment.
Features:
• For solid, booming drives and accurate iron shots
• Create more ball spin on wedges and short irons
• Studies show that cleaner balls lead to fewer putts
010115
Use on:
• Drivers
• Irons
• Shoes
• Balls
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
30.41
Cleaners and Degreasers
Surface Disinfectant
Part #74261 – 15.5 oz.
(Disinfects on hard, nonporous inanimate environmental surfaces)
Disinfects on such bacterial-and viral-carrying surfaces as toilet seats, telephones, garbage and
refuse cans, urinals, athletic equipment, light switches, bed pans, empty hampers and other
out of the way places. Disinfects hard, non-porus surface of shoes and slippers. Controls mold
and mildew on mattresses, awnings, shower curtains, leather goods. Controls mildew and mold
growth on painted or finished walls, ceilings and woodwork in closets, basements, attics, storage
areas, summer cottages, damp and musty corners. Deodorizes and reduces annoying odors.
Use to control odors in hospitals and nursing homes. Effectively suppresses odors caused by
mold and mildew.
Features
Kills the following:
• Influenza A2/Hong Kong Virus
• Influenza A(H1N1)
• Aspergillus niger (ATCC 16404)
• Human Herpes Simplex Virus Type 1 (ATCC VR-733F) and Type 2 (ATCC VR-540)
• Human Immunodeficiency Virus Type 1 [HIV-1 (AIDS virus)]
• Methicillin Resistant Staphylococcus aureus (MRSA) (ATCC 33591)
• Mycobacterium tuberculosis var bovis (BCG)
• Polio Virus Types 1 and 2
• Pseudomonas aeruginosa (ATCC 15442)
• Salmonella choleraesuis (ATCC 10708)
• Staphylococcus aureus (ATCC 6538)
• Trichophytonmentagrophytes (ATCC 9972)
• Vancomycin Resistant Enterococcus faecalis (VRE) (ATCC 51299)
Dis-N-Clean™
Part #74188 – 16 oz.
(Foaming disinfectant cleaner)
Designed for general cleaning and deodorizing. Cleans and disinfects against micro-organisms.
Non-abrasive. Prevents and controls mold and mildew and the odors they cause on hard
non-porous surfaces.
Features
• Multi-purpose cleaner – cleans, shines, disinfects and deodorizes
• Industrial strength formula – tough on soap scum
• Easy-to-use – no scrubbing or rinsing necessary
• Non-abrasive "surface safe" – won't scratch fiberglass
• Fresh clean scent – leaves pleasant odor
• Kills HIV on pre-cleaned environmental surfaces
• Contains no CFCs – won't harm ozone
30
Applications
• Designed for general household cleaning in hospitals, institutions, nursing homes,
offices, schools, motels and hotels
• For use on non-porous hard surfaces such as fiberglass, chrome, plastic, baked enamel
and glazed porcelain
30.42
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
010115
Cleaners and Degreasers
Cleaner/Degreaser
Part #74265 – 32 fl. oz.
(A thick, heavy-duty spray & wipe cleaner/degreaser)
Destroys grease and grime on contact leaves a pleasant lemon/lime fragrance.
NS
AI
NO CFCs
W
CO
CH
HI
NT
Features
• THIX' -O- TROP'IC: The phenomenon exhibited by certain gels of becoming thick
when shaken and returning to a fluid liquid upon standing
• Cuts through tough oils with ease
• Leaves a clean residue free surface
• Stays and works where you spray it
NO CFCs
AY
ER
PL
DE
ET
ET
HE OZONE
L
Applications:
• For use on all hard surfaces
• Will not affect paint, glass or mirrors
• Works great on grout
• Simply spray and wipe away grease, grime, oil, carbon, soot, smoke film, magic marker,
crayon, lipstick and more
Glass & Surface Cleaner
Part #74264 – 32 fl. oz.
(Non-ammoniated, thick, ready to use cleaner with sprayer)
NO CFCs
W
CO
NS
AI
Features
• THIX' -O- TROP'IC: The phenomenon exhibited by certain gels of becoming thick
when shaken and returning to a fluid liquid upon standing
• Formulated with the revolutionary detergent system LS2
• Lifts away the toughest soils on all glass surfaces
• Wipes off quickly, without streaks or rainbows
• Cleans, restores, shines
• Will not cause build-up on surfaces
• Pleasant citrus crème fragrance helps deodorize while it cleans
CH
HI
NT
Designed to quickly and effectively remove dirt, grease,grime and other contaminants from a
variety of hard surfaces without the possibility of streaking or leaving behind an unsightly film.
PL
DE
ET
ET
AY
ER
NO CFCs
HE OZONE
L
Applications:
• Mirrors, windows, automotive glass, tile, porcelain, chrome, stainless steel and white boards
• Will easily remove (without streaking) the heavy film left from cigarette, cigar and pipe smoke
on the inside of the glass
Clean & Fresh Bathroom Wipes
Part #74457 – 160 count
(You can be assured of a clean, healthy and useable bathroom every time.)
Each wipe is premoistened with a potent formula that cleans on contact and evaporates within
seconds. Biodegradable and completely flushable. Won't cause plumbing problems or back-ups.
Features
• Premoistened with a potent formula that cleans on contact and evaporates within seconds
• Biodegradable fabric wipes
• Quick and easy-to-use, just wipe and flush down toilet
• Compliant with ASPM Flushability Specification
• Will not cause plumbing problems or back-ups
Applications:
• Toilet seats, bathroom fixtures, door handles, other hard surfaces
• DO NOT use as toilet tissue or for personal cleansing
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.43
30
Cleaners and Degreasers
Glass Cleaner
Part #74120 – 17.75 oz.
(Strong, ammonia-based glass and surface cleaner)
A modern professional formula that cuts through the toughest kinds of dirt with little effort. It
contains no silicone and is fortified with ammonia to dissolve smudge, soot, greasy film and
smears. No streak formula!
Features:
• Removes dirt and grime
• Spray on and wipe dry
• Leaves no film
• Ammonia-fortified
• Contains no wax or silicone
Applications:
• Ideal cleaner for windows, mirrors, windshields,
stainless steel, formica, sinks, tile and chrome
Glass Cleaner Wipes
Part #74536 – 70 count
(Strong, ammonia-free pre-moistened glass / surface cleaner towels)
Easiest and quickest way to clean your glass and windows and keep them looking like new.
Premoistened with a powerful ammonia-free formula. Removes dust, dirt, oil and grease smudges,
water spots, fingerprints and smoke film from any glass surface and leaves it with a dazzling shine.
Features:
• Ammonia-free
• Streakproof
• Non-flammable
PVA Wipes
Applications:
• Ideal cleaner for mirrors, light fixtures, windshields,
display cases, shower doors, glass tables,
computer screens, chrome, tile and porcelain
Part #74528 – 80 count
(Paint, varnish and adhesive pre-moistened cleaning towels)
Convenient, multipurpose towels eliminate the need for water or other cleaners and are designed to
absorb soil and not transfer back on hands. Conditions hands with aloe, vitamin E and emollients. Hands
will be clean, dry and non-sticky. Cleans most surfaces quickly and easily.
Features:
Applications:
• Fast, effective non-shredding, gentle on skin
• Removes adhesives, ink, nail polish, paint,
• Removes grease, grime, tar, carpet stains and more
varnish, scuff marks, permanent marker,
• Removes odors from hands such as diesel,
counter stains and many types of soils
gasoline, fish and onion smells
• Use to clean hands, tools, equipment, leather
• Non-flammable
tennis/sports shoes and recreational items
30
IMPORTANT: Pre-test plastic surfaces for compatibility. Do not use on polished brass or fine furniture. May not be suited for
certain clear plastics such as plexiglass or styrene.
30.44
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Cleaners and Degreasers
Stainless Steel Cleaner Wipes
P/N 74610 – 40 count
(Cleans, Shines and Protects Surfaces in One Step)
When stainless steel becomes soiled with fingerprints, dirt and residue, these wipes quickly
remove heavy soils and restore a brilliant shine. Stainless Steel Wipes are pre-moistened
with a powerful, VOC-compliant solution that effectively removes grime yet won’t harm
stainless steel.
Features:
• Cleans, polishes and brightens stainless steel surfaces
• Leaves a protective barrier to prevent water marks and corrosion
• Formulated for more even coverage and can be buffed out if desired
• Leaves a pleasant citrus fragrance
Applications:
Cooking/Refrigeration Equipment • Vending Machines • Beverage Dispensers
Laundry Machines • Elevator Doors and Walls • Escalator Walls • Restroom Stall Partitions
Quik-Shine™ Metal Polish
Part #74173 – 5 oz.
(Metal polisher and cleaner)
Cleans and polishes all metal surfaces. Removes rust and corrosion instantly. Leaves no deposits
in the crevices of metal work.
Features:
• Cleans and polishes
• For use on all metal surfaces
• Instantly removes rust and corrosion
Applications:
Silver • Gold • Brass • Nickel • Copper
Pewter • Steel • Aluminum • Chromium
Zinc • Wheels • Boat Fittings • Tools
Fishing Gear • Sinks • Showers • Campers
Metal Cleaner & Tarnish Remover
(Polishes and protects, leaving a lustrous shine)
Part #74537 –
16 oz.
This unique chemical action formula removes tarnish and soil quickly and easily. Use on brass,
bronze, copper and nickel. No need to wait for product to dry. Polishes and protects while leaving
a lustrous shine. Polished surface also resists tarnishing.
Features:
• Unique chemical action formulated to remove
tarnish and soil quickly and easily
• Polishes and protects
• Leaves a lustrous shine
Insta-Clean™
Applications:
Hand Rails • Kick Plates • Plaques
Door and Furniture Hardware
Statues • Light Fixtures
30
Part #74121 – 12.75 oz.
(Rubber and vinyl cleaner and protectant)
Cleans and shines all rubber, vinyl and other synthetic surfaces without washing or wiping —
just spray on and walk away! Its unique self-cleaning foaming action quickly removes cakedon dirt while leaving a long lasting, high gloss shine. Protects surfaces from discoloration and
oxidation. Will not harm aluminum or painted surfaces.
Features:
• Powerful foaming action
• No washing or wiping necessary
• Leaves a high gloss protective shine
010115
Applications:
Ideal for use on rubber and vinyl components
of machinery and equipment; vinyl and plastic
furniture; and truck/auto tires and plastics –
It makes them look showroom new!
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
30.45
Cleaners and Degreasers
Baseboard/Stripper Cleaner
Part #74174 – 18 oz.
(Superior cleaning due to stability on vertical surfaces)
Specially formulated with powerful cleansers which allow soiled areas to be treated while keeping
them looking clean and attractive. Removes scuff marks, wax build-up, grease and grime.
Features:
• Heavy duty jelled formula clings to vertical surfaces for complete penetration and removal
• No phosphates
• No caustics
• Liquifies finish in minutes
• No harmful residues
• No harmful vapors
Applications:
• Baseboard, floors, and ceramic wall tile
Contact Cleaner P.S.
Part #74704 – 13 oz.
(Plastic safe industrial strength cleaning solvent)
This non-flammable, fast drying industrial strength cleaning solvent is specifically formulated
for precision cleaning and degreasing of electrical contacts, switches, relays and controls in
electromechanical assemblies. It is non-corrosive, non-conductive, safe for sensitive metals and
most plastics. Can also be used on energized equipment. Powerful spray stream removes dust,
dirt, oil, grease and oxides – leaving no residue after evaporation.
Features:
• Instantly removes grease, oils and dirt
• Safe for use on energized equipment
• Safe on most plastics
• Noncorrosive / nonconductive / nonflammable
• Adjustable spray nozzle – low / medium / high
Applications:
• For use on electrical contacts, switches, relays and controls in electromechanical assemblies
Degreaser
Part #74111 – 15.75 oz.
(Kerosene-based degreaser)
30
Specially formulated to clean all mechanical engines, machinery, tools and even greasy floors.
Removes dirt, grease and varnish deposits by simply spraying on and flushing off with water.
Best cleaning results are obtained when engine is at normal operating temperature.
Features:
• Non-corrosive
• Low odor
• Penetrates through grease and grime
• Easy to use
• Water soluble
Applications:
• For use on all mechanical engines, machinery, tools, floors, equipment, trucks, forklifts,
chains and cables
30.46
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
010115
Cleaners and Degreasers
High Performance Safe-Acid Cleaner
P/N 74615 – 1 qt. l P/N 74616* – 1 gal. l P/N 74617* – 5 gal. l P/N 74618* – 55 gal.
* Non-stock item. Please call for delivery.
(Non-toxic, Non-corrosive, Non-fuming, Biodegradable Cleaner)
This liquid multipurpose cleaner generates the heavy duty cleaning power of an acid, yet
it is safe and mild like liquid dish soap. Remarkable formula contains a special blend of
surfactants, organic salts and proprietary additives to create an acid-replacement cleaner that is
environmentally safe and biodegradable. Effective against rust, hard water stains, calcium, scale
and lime deposits, beer stone, milk stone, soap scum, scuff marks, stains and soils, grease.
Features:
• Biodegradable, multifunctional high-performance cleaner.
• Contains a special blend of surfactants and proprietary organic additives.
• Concentrated formula offers multiple dilution rates.
For use on:
Stainless Steel • Copper • Brass • Aluminum • Concrete • Terrazzo • Stone • Ceramic
Porcelain • Fiberglass • Brick • Appliances • Food Surfaces* • Steam Tables
Coffee makers • Humidifiers • Toilets • Urinals • Tile and Grouting • Showers • Tubs
Sinks • Floors • Walls • Fish Tanks • Vents
* Potable water rinse required.
Citrus Grease Digester
P/N 974250 – 1 Quart
(Powerful citrus base, biodegradable cleaner)
Revitalizes sluggish disposal systems, quickly reducing buildup of grease and slime in sewage
treatment equipment without affecting bacteral activity. Effectively controls odor. Will not harm
metal pipes. Eliminates heat generation. Nonacid. Noncaustic. Noncorrosive.
Features:
• Unclogs, deodorizes and degreases
• Extremely effected in drains, grease traps,
septic systems, dry wells and cesspools
• Environmentally safe
• All natural citrus base
Pro-Tex
Applications:
• Used in sewage treatment plants,
landfills, waste disposal facilities and
for the maintenance of drains, refuse
trucks and cans, and garbage areas.
Part #74152 – 17.75 oz.
(Anti-static cleaner and protector)
An excellent brightener and protector which resists scratches, marks, smudges and water spots.
Use on glass, mirrors, chrome, tile and laminated plastics. Formulated to keep automobile interiors
and exteriors cleaner and brightener with less maintenance.
Features:
• Anti-static cleaner and protector
• Resists Scratches and finger smudges
• Excellent CRT screen cleaner
• Long lasting – requires infrequent cleaning
Applications:
• Use for protect CRT screens, glass, mirror, chrome, paint finishes, vinyl, tile, leather and
laminated plastics
010115
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
30.47
30
Cleaners and Degreasers
Electronic Equipment Wipes
(Eliminates static to avoid electronic data loss)
Part #74456
30 Count - 7'' x 9'' Towels
Wiping down electronic equipment with these wipes, protects devices from static electricity and
avoids dust. Premoistened with a special formula that neutralizes the effects of static electricity.
This avoids the loss of important data stored on computer equipment such as hard drives.
Features:
• Special formula eliminates static
to protect the loss of data
• Eliminating static keeps dust
from collecting on equipment
• Cleans and sanitizes surfaces
• Towels can be used on almost
any electronic equipment
Applications:
• LCD screens
• Telephone ear & mouth piece
• Copiers
• Office equipment
• Keyboards
• Printers
• Computer terminals
• Fax machines
• Televisions
Dust Blaster™
Control Valve
with Nozzle
P/N 8214
Disposable
Cylinder (38g)
P/N 74182
Dust Blaster™
• P/N 8209
Complete System
30
Part #8209 – Complete System
(Powerful, ozone safe, precision duster)
Instantly removes dust and particles from equipment, electronics, computers, medical devices
and camera lenses. Contains 100% pure and safe natural gas. No CFC’s or HCFC’s.
Convenient cylinders are disposable and recyclable. The precision control valve is reusable.
Features:
• Ozone safe
• Powerul 850 psi jet action
• Five times stronger than aerosols
• Reusable precision valve
Dust Blaster TM P/N 8209 includes:
• Control Valve with Nozzle
• 12 Disposable Cylinders (38g)
P/N 8214
P/N 74182
Applications:
• For use on electronics, computers, medical devices and camera lenses
Dust Blaster Max
Part #74175 – 10 oz.
(Inert, dry gas duster)
Instantly removes dust, lint and particulates from equipment and delicate electronic
assemblies. Cleans with a dry blast without risk of scratching or damaging surfaces. Ultra-pure,
non-flammable formula is safe to use on energized equipment.
Features:
• Instantly removes dust / particulates
• Cleans delicate materials
• Safe for most surfaces
• Ultra-pure, filtered to 0.2 Microns
30.48
Applications:
• For use on hard-to-reach areas, "touch-sensitive"
surfaces (internal components of TV sets, cameras,
camcorders, VCRs, computers, audio equipment,
CD players, etc.) and coated glass or plastic lenses
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
010115
Cleaners and Degreasers
Easy-Out Stain Remover
Part #74176 – 32 fl. oz.
(Non-hazardous, water-based, carpet and upholstery stain remover)
Quickly and easily removes the following stains from carpet, upholstery and other fabrics:
blood, candle wax (break up first), catsup, chocolate, coffee, cosmetics, crayon, food, fruit
juice, grass, grease, grime, iodine, latex paint, liquor, mildew, oil, pet stains, shoe polish, tea,
urine, washable ink, wine and many more.
Features:
• Quickly and easily removes stains from carpet
and upholstery
• Contains no solvents or hazardous ingredients
• Leaves fabrics clean and fresh
Applications:
• For carpet, upholstery
and other fabrics
NOTE: Dyes, indelible ink or stains set by
heat may not be possible to remove.
Carpet/Upholstery Spot Remover
(General purpose water & oil-based stain remover)
Part #74262 – 17 oz.
This handy aerosol spray quickly dissolves away tough stains like grease, oil and lipstick from fabric
or fibrous material without heavy scrubbing. Its powerful formula removes both water-based and
oil-based stains and even removes stubborn, dried-on stains.
Features:
• For use on carpets, upholstery, curtains, drapes
• Effectively removes both water and oil-based stains
• Safe for use on most fabrics
• Use as a pre-spotter prior to carpet extraction
Applications
Removes:
• Ink
• Grease
• Tar
• Oil
• Shoe Polish
•
•
•
•
•
Carpet Spot Direct
Cola
Coffee
Lipstick
Wine
Pet Stains
Part #74258 – 18 oz.
(Powerful carpet stain and spot remover)
Quickly and easily removes protein based stains due to dirt, ink, grease, oil, mud, ketchup, urine,
vomit, coffee, tea, alcoholic beverages, soft drinks and bloods.
Features:
• Pinpoint stream sprays upside down onto stains without heavy overspray
• Quickly saturates materials for instant cleaning
• Leaves no residue behind
• Cleans and degreases with water soluble solvents, will not soften carpet backings
• Contains an odor modifier which destroys odor due to urine and vomit through oxidation catalysis
• Leaves a pleasant fragrance
Applications:
• Use to remove stains due to dirt, ink, grease, oil, mud, ketchup, urine, vomit, coffee, tea,
alcoholic beverages, soft drinks and blood.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.49
30
Cleaners and Degreasers
Quick Clean
Part #74105 – 17.75 oz.
(General purpose foaming cleaner)
The ultimate general purpose quick cleaner removes dirt, grease and grime.
Features
• Removes dirt, soil and grime
• Safe on most surfaces
• Quick-acting and easy-to-use
• Spray on and wipe off
Applications
• For use on equipment, walls, plastic, vinyl,
rugs, drapes, wood surfaces, fixtures,
furniture and painted surfaces
Quick-Solv™
Part #74186 – 19 oz.
(Nonflammable, fast-evaporating cleaner/degreaser)
A nonflammable, fast-evaporating cleaner that penetrates instantly to remove dirt, oil, grease and
wax. Increases the life of electrical components by removing foreign materials that can cause costly
downtime. High dielectric strength of 26,000 volts per mil. Degreases more thoroughly and several
times faster than alkaline cleaners. Equipped with high-delivery valve for cleaning efficiency and
5" extension tube for hard-to-reach areas.
Features:
• Strong solvent formulation quickly removes grease, dirt and oil
• High dielectric strength prevents shorting of electrical and electronic equipment
• No flash or fire point – eliminates fire and explosion hazards
• Fast evaporation speeds clean-up and downtime
• Noncorrosive, nonconductive and nonstaining for safer application
Applications:
• Cleaning and degreasing of all parts, equipment and machinery
• Excellent for cleaning sheet and strip steel prior to galvanizing
• Ideal for degreasing bearings and engine components
Citrus Blast - H.D.
P/N 74142 – 16 oz.
(Heavy Duty Industrial Foaming Degreaser)
Citrus Blast - H.D is a heavy duty industrial degreaser with a foaming jet stream spray pattern.
It is a very effective degreaser without the use of harmful caustics or solvents.
30
Features:
• Strong solvent formulation quickly removes grease, dirt and oil
• High dielectric strength prevents shorting of electrical and electronic equipment
• No flash or fire point – eliminates fire and explosion hazards
• Fast evaporation speeds clean-up and downtime
• Noncorrosive, nonconductive and nonstaining for safer application
Applications:
• Powerful foaming spray dissolves grease, oil, grime and more
• Excellent for accumulations of grease or tar and asphalt on engines or engine parts
• For use on coils, fins and filters
Use on:
• Machinery • Tools • Industrial equipment • Walls • Concrete • Protective coatings
30.50
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Cleaners and Degreasers
FACILITY WIPES (ALL-SURFACE CLEANING WIPES)
Facility Wipes
Designed to clean and deodorize any surface, anywhere. They are excellent for quick and
easy cleaning of equipment, furniture and facilities. Wipe down surface with fresh towel and
throw towel away when finished. Good for cleaning metal, glass, tiles and ceramic.
Features and Benefits
• 800 wipes per roll
• Cleans and deodorizes surfaces on contact
• Fast and easy to use towel, one step cleaning
• Wall mounted dispenser allows convenient individual use
P/N 28235
Use With Center-Pull Dispenser (P/N 1789)
• Single-sheet release requires only one hand to tear off
• Made of tough impact resistant materials
• One of the most vandal-proof, break resistant,
chemical and flame resistant products
• For heavy use applications
Applications
• Athletic clubs • Schools • Hospitals • Nursing homes • Restaurants • Health clubs • Offices
P/N 1789
DESCRIPTION
PART
Facility Wipes (800 Wipes Per Roll - 8" x 10")
Center-Pull Dispenser
28235
1789
SHOP WIPES (HIGH-POWERED VERSATILE CLEANER)
Designed for use in industrial and manufacturing settings, each towel is pre-moistened with a powerful
cleaning formula capable of cleaning hard-working hands, as well as non-porous surfaces. Made from
an abrasive, yet non-scratching fabric that helps lift away heavy deposits of grime and dirt off hands and
surfaces as well as leaving behind a fresh citrus scent. Scrub surfaces with abrasive side of towel until
the dirt is loosened, then use the smooth side to wipe surfaces clean and discard.
Features and Benefits
• 400 wipes per roll
• High powered multipurpose cleaner
• Effective against tar, paint, wax, grease, adhesives and ink
• Abrasive, yet non-scratching fabric aids in cleaning
• Natural oils and emollients, safe for hands & skin
Use With Center-Pull Dispenser
• Offers single-sheet release
• Requires only one hand to tear off
• Made of tough impact resistant materials
• One of the most vandal-proof, break resistant, chemical and flame resistant products
• For heavy use applications
P/N 28236
30
P/N 1789
Applications
• Auto shops • Work benches • Maintenance areas • Offices • Plumbing sites • Marinas
• Break rooms & kitchens • Construction sites • Printing & painting areas • Manufacturing
DESCRIPTION
PART
Shop Wipes (400 Wipes Per Roll - 8'' x 12'')
Center-Pull Dispenser
030115
040115
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
28236
1789
30.51
Skin Care
STOKO® XTREME CARE CREAM
Xtreme Skin Conditioner
Use on hands, face and any other at-risk areas exposed to extreme conditions. Temporarily
protects against the drying effects of harsh, cold environments, outdoors or indoors.
Features and Applications
• Contains Allantoin, Panthenol and Glycerin to strengthen the skin’s natural defenses
• Helps protects skin from natural elements such as very low temperatures and lack of humidity
• Use on hands, face and any other at-risk areas exposed to extreme conditions
• Promotes healing of very dry, irritated skin
• Can also provide relief for severely dry skin
• Does not freeze
• Will dispense easily even at lower temperatures
• Passed Lineman’s Glove Testing
• Silicone-free
DESCRIPTION
PART
Stoko Xtreme Care Cream (3.38 fl. oz.)
®
74454
STOKOLAN® SKIN CARE CREAM
Concentrated Skin Conditioner
Frequent hand washing can lead to dry, chapped, cracked skin causing employees to avoid proper
hand washing. With Stokolan® Skin Care Cream, employees are able to achieve the proper balance
between effective cleansing and skin compatibility and help reduce the incidence of dermatitis in the
workplace.
Features and Applications
• Concentrated conditioning cream replaces lost moisture after washing hands (silicone-free)
• Replaces the oils and lipids the skin loses in the course of a hard day’s work
• Ideal for chapping, chafing and irritated skin
• Keeps skin feeling healthy and smooth
• Ideal for use in any industrial setting, as well as many other workplace environments
• Particularly necessary when skin is exposed to cold and/or dry climates or harsh
working conditions
DESCRIPTION
PART
Stokolan® Skin Care Cream (3.38 fl. oz.)
74453
30
30.52
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
030115
040115
Skin Care
HANDI-SANI
Instant Hand Sanitizer
Red Lion™ Handi-Sani instant hand sanitizer is a light and refreshing hand sanitizing spritz,
enhanced with moisturizers.
Features
• Active ingredient: 62% Ethanol
• pH: 7.5
• Helps reduce cross-contamination
• Kills 99.99% of E. coli, Salmonella enterica and
Staphylococcus aureus (MRSA) in 15 seconds
•
•
•
•
•
•
FDA registered
Provides convenience and portability
Fast-drying
Conditions skin
Requires no water
FDA Approved
Applications
• Hospitals, nursing homes and physical therapy rooms • Schools (buses, locker rooms)
• Health clubs and spas • Daycare centers • Transportation (airports, buses, subways, trains, etc.)
DESCRIPTION
PART
Handi-Sani (4 oz.)
74487
SANI-SMOOTH
Hand Sanitizing Foam
Red Lion™ Sani-Smooth foaming aerosol hand sanitizer is alcohol based and allows you to
sanitize your hands when hand washing is not possible. Contains a unique blend of emollients
and conditioners that leaves your hands silky smooth and soft. Using a foaming aerosol hand
sanitizer is the preferred method by hospitals over the liquid variety. Sani-Smooth is a more efficient
way for employees to frequently clean their hands and thus cut down on the spread of infection.
Features
• Active ingredient: Ethyl Alcohol 62%
• pH: 7.6
• Preferred by hospitals over
liquid hand sanitizing products
• Non-Allergenic sanitary foam
• Removes dirt and bacteria without
the need of water
• Provides convenience and portability
• Over 600 estimated uses per can
• Mounting hardware included with dispenser
• FDA Approved
Applications
• Hospitals, nursing homes and physical therapy rooms • Schools (buses, locker rooms)
• Health clubs and spas • Daycare centers • Transportation (airports, buses, subways, trains, etc.)
P/N 74486
P/N 1819
Dispenser
DESCRIPTION
PART
Sani-Smooth (16 oz.)
Dispenser
030115
040115
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
74486
1819
30.53
30
Skin Care
SOAPS
ANTIMICROBIAL HAND CLEANER AND SANITIZER
A Thick One-step Hand Cleaner and Sanitizer that conforms to the E-2 Designation Requirements of the USDA
Red Lion™ Antimicrobial Hand Cleaner and Sanitizer is powered by Benzalkonium Chloride,
which is effective against a broad spectrum of gram positive and gram negative bacteria.
Features and Benefits
• Approved for use in all USDA and federally inspected plants
• Fragrance and dye free advanced skin care formula
• Rich, mild lather that is pH balanced (5.5-7.0)
• 100% biodegradable
• Industrial size
• Industrial grade
• 85 fl. oz. dispenser sold separately (shown, P/N 1832)
Applications
• Suitable for use in all food manufacturing and processing facilities which require
the highest levels of personal sanitation as part of their GMP
• Ideal for use in meat and poultry processing industries
• Use in other food handling environments such as restaurants and supermarkets
DESCRIPTION
PART
Antimicrobial Hand Cleaner and Sanitizer, 85 fl. oz.
Soap Dispenser, for 85 fl. oz. Bottles, Color: black
74629
1832
HEAVY DUTY SCRUB HAND SOAP
Concentrated Industrial Hand Cleaner
Fortified with leading edge skin conditioners and free floating polymer scrubbers,
Red Lion™ Heavy Duty Scrub Hand Soap tackles the toughest dirt, grease and grime.
Leaves hands clean and conditioned.
30
Features and Benefits
• Environmentally friendly formula
• Enriched with multiple emollients
• Promotes healthy skin care
• Contains no harsh petroleum solvents
• New age polymer scrubbers float away
• Green color, mild citrus scent
• 120 fl. oz. dispenser sold separately (shown, P/N 1830)
DESCRIPTION
PART
Heavy Duty Scrub Hand Soap, 120 fl. oz.
Heavy Duty Scrub Hand Soap, 18 fl. oz.
Soap Dispenser, for 120 fl. oz. Bottles, Color: gray
74630
74633
1830
30.54
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
030115
040115
Skin Care
SOAPS
H.D. CITRUS HAND SOAP
A Liquid, Heavy-duty Hand Cleaner
Red Lion™ H.D. Citrus Hand Soap is a formulation based on a synergistic blend of
detergents, emulsifiers, solvents, and emollients. It works equally well with or without
rinse water. This soap rinses easily, gently replaces the skin’s oils, and leaves hands feeling
clean and soft. Contains no pumice.
Features and Benefits
• Multiple emollient package
• Leaves skin soft and moisturized
• After cleaning, a small amount may be used as a hand lotion to recondition skin
• Orange color, citrus scent
• 120 fl. oz. dispenser sold separately (shown, P/N 1830)
Applications
• Easily removes dirt, grease, oil, grime, tar, asphalt, ink, paint & adhesive
• Can be used “on-the-job” because it easily wipes away
with paper towels or cloths anywhere water is not available
• Also works wonderfully when rinsed with water
DESCRIPTION
PART
H.D. Citrus Hand Soap, 120 fl. oz.
H.D. Citrus Hand Soap, 18 fl. oz.
Soap Dispenser, for 120 fl. oz. Bottles, Color: gray
74631
74632
1830
CHERRY IMPACT HAND SOAP
Industrial Hand Cleaner with Cherry Fragrance
Red Lion™ Cherry Impact hand soap was developed specifically for professional technicians.
Its super thick concentrate contains scrubbing particles, and stays on your hands during washing.
Contains superior emollients to reduce drying and cracking.
Features and Benefits
• Medicated to promote healthy skin care
• Low solvent content formula
• Removes stubborn grease and oil
• Leaves hands feeling conditioned
• Red color, pleasant cherry scent
• 120 fl. oz. dispenser sold separately (shown, P/N 1830)
30
DESCRIPTION
PART
Cherry Impact Hand Soap, 120 fl. oz.
Cherry Impact Hand Soap, 18 fl. oz.
Soap Dispenser, for 120 fl. oz. Bottles, Color: gray
74471
74472
1830
030115
040115
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
30.55
Skin Care
SOAPS
MAGIC HAND SOAP
All Natural Industrial Hand Cleaner
Red Lion™ Magic Hand Soap contains walnut shell scrubbers to clean the toughest soils.
It cleans the dirtiest hands like magic! Contains the anti-microbial “PCMX”.
Features and Benefits
• Fortified with supreme skin conditioners and biodegradable scrubbers
• Non-solvent formula eliminates drying and cracking
• Contains superior skin emollients and skin conditioners
• Cleans the dirtiest hands like magic
• No phosphates, dyes or perfumes
• Contains natural walnut shell scrubbers
• Thick concentrated formula reduces hand soap use by up to 75%
• Washes away completely with no greasy residue
• Brown color, mild citrus scent
• 120 fl. oz. dispenser sold separately (shown, P/N 1830)
DESCRIPTION
PART
Magic Hand Soap, 120 fl. oz.
Magic Hand Soap, 18 fl. oz.
Soap Dispenser, for 120 fl. oz. Bottles, Color: gray
74458
74459
1830
30
30.56
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
030115
040115
Skin Care
HAND CLEANER
POW-R-SCRUB HAND CLEANER
Fast Acting Hand Cleaner with Pumice Scrubbers
Professional strength pumice hand cleaner immediately goes into action to power out the worst grease and
grime. Instantly attacks grease, grime, soils, resins, epoxies, paint, glue and rubber gasket, plus any other
soil you can get your hands into. This convenient squeeze bottle, with its easy-to-use self-dispensing cap,
eliminates the need for wall mounted dispensers.
Features
• Professional strength pumice hand cleaner
• Instantly attacks grease, grime, soils, resins, epoxies,
paint and glue
• Contains fine pumice scrubbers
• Softens and protects skin with aloe and lanolin
Applications
• Removes grease/grime, inks, paint,rubber gaskets,
epoxies/glue, soil and resins
DESCRIPTION
PART
Pow-R-Scrub Hand Cleaner (15 fl. oz.)
74416
30
030115
040115
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
30.57
Skin Care
H.D. Citrus Scrub
P/N 74521 – 128 fl. oz.
(Strong, citrus-based hand cleaner with pumice scrubbers & conditioners)
This citrus-based hand cleaner scrubs your hands clean quickly and naturally. Pumice scrubbers
gently remove the toughest dirt, grease, grime, soils, resins, printer's ink, paint, glue, rubber gasket
and tile cements. Contains lanolin, aloe and jojoba to moisturize skin. Regular use helps keep hands
clean and conditioned. H.D. Citrus Scrub is pH balanced and bio-degradable*.
(Use with P/N 1806 Hand Cleaner Dispenser Pump).
*Biodegradable according to OECD-301E.
Features:
• Industrial strength citrus formula
• Fine pumice scrubbers
• Removes the toughest grease, dirt and grime
H.D. Multi-Purpose Citrus Towels
(Industrial Degreaser for Hands, Tools, and Surfaces)
P/N 74609 – 90 count
Multi-Purpose Citrus Towels are pre-moistened with a high-powered, multi-purpose,
grease-cutting formula that lifts away grease, tar, adhesives, wax, ink, paint and lubricants
from hands and other non-porous surfaces. The superior grease-grabbing performance is ideal
for use on tools, equipment, and hands. Natural oils and an emollient are safe for hands and skin,
and will not cause drying, unlike similar products. Non-scratching towel is abrasive on one side and
smooth on the other.
Features:
• Won’t scratch hands or surfaces
• No rinsing, no residue
• Fresh citrus scent
• Powerful grease removal on a convenient pre-moistened wipe
• Abrasive towel material provides tough scrubbing action
• Fortified with an emollient so they won’t dry hands and skin, unlike similar products
• Ideal as a point-of-use waterless cleaner
• 50-state VOC compliant
PVA Hand Cleaner
P/N 74512 – 15 oz.
(Paint, varnish and adhesive hand cleaner)
Safely and effectively removes paints, urethanes, sealants, adhesives, stains, plastic fillers, putty and
more. Fortified with 8 skin care ingredients and micrograin scrubbers for extra cleaning power. Rinses
thoroughly with no unpleasant odor or sticky afterfeeling. Complies with VOC Consumer Product Rules.
Rub a small amount into the hands, add a little water and rub hands vigorously. Rinse hands and dry
thoroughly. Environmentally friendly with no greasy residue. Leaves a fresh, clean scent.
30
Applications:
Features:
Removes stain/varnish, urethane paints,
• Unique DBE Solvent Formula
primers, silicones, resins, enamels, oil paints,
• Protects silicone-sensitive accessories
lacquers, adhesives/sealants, clear coats,
• Skin-friendly formula – Helps ensure healthy hands
body fillers and grease/grime
• With vitamin C antioxidant
• Helps protect skin from UV-related damage
• With vitamin E moisturizer
• Helps improve elasticity and smoothness of the skin
• Cuts Through Paint, Varnish, Adhesives and Other Tough Soils Without Damaging Hands
• Softens and Shields Skin with Aloe, Provitamin B5 and Jojoba
30.58
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
030115
Skin Care
Citrus Clean GF
P/N 74427 – 1 Pint
(Waterless Hand Cleaner)
A powerful hand cleaner formulated with d-Limonene to safely dissolve and remove heavy soils
from skin.
Features:
• This effective grit-free (no pumice) hand cleaner is formulated with natural orange peel extracts
• Extracts dig deep down into the skin’s pores to remove even the toughest dirt and grease
• Contains lanolin and other special emollients to prevent hands from becoming red and chapped
• An easy and convenient way to keep hands clean
• Contains no petroleum solvents
• Does not need to be rinsed with water
Applications:
Waterless hand cleaner that digs deep down into the skin’s pores to remove even the toughest
dirt and grease.
Protective Skin Cream
P/N 74449 – 18 oz.
(USDA rated E-4 Skin Protectant)
Protective Skin cream provides an “all-day” invisible greaseless film of protection on the skin
against irritating materials. Its excellent emollient quality is ideal for chapped cracked skin.
Clean-up with just soap and water to wash away the protective coating, dirt and irritating
materials.
Features:
• Easy On...Easy Off!
• USDA rated E-4
Applications:
Protects Against Paints, Grease, Inks, Oils, Solvents, Gasoline, and Cement Burns
Hand Sanitizing Wipes
P/N 74539 – 70 count
(With Aloe and Vitamin E Antiseptic)
Formulated with aloe and antioxidant Vitamin E to moisturize the skin. This effective formula cleans
hands while killing bacterial. Towels are made from a non-abrasive fabric that is gentle to the skin.
Wipes are easy to use and not messy like sanitizing gels.
Features:
• Kills 99.9% of bacteria
• Leaves a fresh wintergreen fragrance
• Leaves hands feeling fresh
• Quick and easy to use, wipe and discard
Applications:
• For handwashing to decrease bacteria on the skin, only when water is not available
• Before contact with a person under medical care or treatment
050114
080114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.59
30
Insecticides
Bug Be Gone Wipes
Part #74263 – 40 Wipes (6'' x 8'')
(Powerful, fast-acting wipe-on insect repellent)
Repels mosquitoes, chiggers, ticks, deer flies, stable flies, black flies, gnats and fleas on
exposed skin surfaces. Contains 25% DEET, one of the most effective insect repellents
available. Just wipe onto exposed skin, and throw the wipe away.
Features
• Water-Based
• Non-VOC Formula
• No Strong/Offensive Odor
• Leaves No Sticky Residue
• Provides up to 4 hours of
protection
• Convenient, easy to use
• Quick & thorough
• Contains 25% DEET
Repels
• Mosquitoes
• Chiggers
• Ticks
• Deer flies
• Stable flies
• Black flies
• Gnats
• Fleas
Applications
• Construction
• Utility Work
• Road Work
• Sanitation Crews
• Farming
• Gardening
• Camping
• Fishing
• Boating
• Hunting
Insect Repellent
Part #74705 – 6 oz.
(Powerful, fast-acting insecticide)
Repels mosquitos, chiggers, ticks, deer flies, stable flies, black flies, gnats and fleas on exposed
skin surfaces. Contains 25% DEET, one of the most effective insect repellents available.
Features
• Repels mosquitos, chiggers, ticks, deer flies, stable flies, black flies, gnats and fleas
on exposed skin surfaces.
Applications
• Use just enough repellent to cover exposed skin and/or clothing.
• Do not use under clothing
• Avoid over-exposure
Insect Repellent Wristbands
(For Maintenance, Repair and Operations Personnel – Commercial/Military)
Green - P/N 85085
Glow-in-the-Dark - P/N 85086
Pink - P/N 85087
30
Red - P/N 85088
Yellow - P/N 85089
Blue - P/N 85090
All wristbands are sold
in a 3 pack.
Vapors from the insect repelling wristband form a protective shield around the immediate area,
keeping insects a safe distance away. Natural & Effective, made with naturally derived geranoil.
Use just enough repellent to cover exposed skin and/or clothing.Do not use under clothing.
Features
• DEET Free
• Water Resistant – The wristband just keeps working, up to 120 hours
• Packaged in a reusable plastic “pod” to store the wristband, it can be sealed between uses
to preserve the active life of the product
Applications
• Repels mosquitoes, flies, gnats, and no-see-ums
• A good choice for recreational and lighter-duty applications
• Can be worn on belt loops, hatbands, fastened in tents, or applied to other areas
• Designed with a patented break-away strap that snaps if it becomes entangled
30.60
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Insecticides
Fire Ant & Insect Dehydrator
Part #74269 – 3.5 oz.
(Powerful, long-lasting insecticide)
Red Lion™ Fire Ant & Insect Dehydrator contains the quick-killing botanical insecticide, pyrethrum,
an extract of the chrysanthemum flower. Kills insects on contact.
Features
• Provides effective control of
insects upon direct contact
with an added benefit of
flushing these insects to aid
in a more complete kill
• Silicon dioxide provides
long term control through a
desiccating (drying) action
• Kills insects up to 6 months
from initial application
Kills
• Ants
• Carpenter Ants
• Fire Ants
• Pharaoh Ants
• Bedbugs
• Beetles
• Confused
Flour Beetles
• Carpet Beetles
• Red Flour Beetles
• Cockroaches
• Carpenter Bees
• Centipedes
• Crickets
• Earwigs
• Firebrats
• Fleas
• Hornets / Wasps
• Lice
• Dust Mites
Ant and Roach Spray
• Palmetto Bugs
• Scorpions
• Silverfish
• Spiders
• Ticks
• Termites
• Waterbugs
• Weevils
Part #74163 – 11.75 oz.
(Fast acting, long-lasting indoor / outdoor use)
Provides rapid control of houseflies, mosquitos, small flying moths (millers), gnats, wasps
and accessible stages of roaches, ants, water bugs, silverfish, flour beetles, weevils, grain
mites and spiders. In hospitals, patients should be removed from room prior to treatment.
Room should be ventilated two hours after spraying. Do not return patients to room until after
ventilation.
Features:
• Evercide® insecticide
• For rapid control of common pests and insects
• For indoor and outdoor use
• Can be used on bedding and carpeting
• Lasts up to 42 days
Applications:
For use in the home and food and non-food areas of:
• Food Processing Plants • Schools • Warehouses • Office Buildings • Theatres
• Garages • Hotels • Motels • Kennels • Hospitals and Other Listed Areas
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30
30.61
Insecticides
Wasp and Hornet Killer
Part #74161 – 12 oz.
(Powerful, fast-acting insecticide)
Triple action formula kills wasps, hornets and yellow jackets. Instant knockdown. Kills with residual
action as wasps and hornets return to the nest. Sprays up to 20 feet. Dielectric breakdown voltage
of 33,000 volts.
Features:
• Instant knockdown
• Triple action formula
• Kills wasps, hornets and yellow jackets
• Dielectric breakdown voltage of 33,000 volts
• Accurate stream penetrates deep into
hard-to-reach nests
Applications:
For use in the home and non-food areas of:
• Schools • Warehouses • Office Buildings
• Theatres • Garages • Hotels • Motels
• Kennels • Hospitals and Other Listed Areas
NOTE: Do not use in commercial food/feed handling establishments, restaurants or other sites where food/feed is commercially
prepared or processed. Do not apply to pets or contaminate feed, foodstuffs, dishes or utensils.
Bedbug Killer
P/N 74485 – 10 oz.
(For a good night's sleep... Rest Ezzzzzzzzzz)
Controls bedbugs on wood, ceramic surfaces, fabrics and carpet for up to 2 weeks. For use on
all water-safe fabrics and surfaces. Will not stain fabrics.
Features:
• Kills bedbugs and their EGGS, fleas, dust mites, ticks and lice on contact
• For use on all water-safe fabrics and surfaces
• Will not stain
• Ease and convenience of aerosol application
• Extension tube for hard to reach areas, cracks and crevices
• Long lasting, keeps killing up to 2 weeks
Applications:
• For use on mattresses, wood furniture and carpet
30
30.62
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Lubricants
4-Way Plus
Part #74107 – 18 oz.
(Multi-purpose lube and penetrant with high dielectric strength)
Specially formulated to displace moisture on wet ignition systems, electric motors and equipment.
(electrical power must be off). Frees frozen parts, protects metal prior to storage and prevents
rust and corrosion.
Features:
• Displaces moisture
• Dries wet ignitions
• Frees rusted parts
• Prevents rust
• Stops squeaks
• Provides moisture barrier
• Meets government specifications MIL-C-16173D and W-L-800C
Applications:
• Rust preventative for metal parts in machine shops: tools, equipment and similar surfaces
• Tractors, bicycles, cranes and vehicles
• Electrical systems, generators, alternators and starters
Blue Grease
(Calcium Sulfonate complex industrial grease)
Part #74435 – 14 oz. cartridge
Part #74436 – 5 gallon pail
Part #74437 – 15 gallon pail
Part #74438 – 50 gallon drum
Premium grade, calcium sulfonate complex industrial grease is designed for extended
service life and is recommended for multi-application usage in even the most severe
applications across all industries. Due to Blue Grease’s completely shear stable thickener
it has superior rust, corrosion and oxidation resistance while offering the highest level
of EP and load carrying performance obtainable. Blue Grease meets and exceeds the
highest automotive service classification (GC-LB) and makes an excellent grease for
extended service life in all types of high temperature, extreme pressure agricultural,
construction, hauling, mining, logging, and steel mill applications.
Features:
• Superior quality Calcium Sulfonate Complex grease
• Unmatched EP Protection 65 Timken, 620 Weld Point
• Longest re-lubrication intervals will not harden, thin or washout
• Considered waterproof by industry standards
• Maximum operating temps -30°F to 425°F
• Completely heavy metal free and harmful additive free,
contains no antimony, barium, chlorine, lead, or zinc
Applications:
• Electric Motor Bearings
• Ball and Roller Bearings
• Gear Motors
• Anti-Friction Bearings
• King Pins
• Pillow Blocks
• Wheel Bearings
• Kiln Cars
• Fifth Wheel
050114
30
• Universal Joints
• Bucket Pins
• Slides & Ways
• Shakers
• Marine Applications
• Power Plants
• Soot Blowers
• Exhaust Fan Bearings
• Truck Chassis
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.63
Lubricants
Cable & Chain Core Lube
Part #74151 – 14 oz.
(Dry film lube for moisture and saltwater resistance)
Provides protection for metal surfaces in the presence of heat, friction and stress. The moly coats
the metal strands of wire rope and metal links or chains to reduce friction and wear. It extends the
life of equipment by preventing metal corrosion. The ultimate protection against rust.
Features:
• Provides ultimate protection
• Penetrates to core of wire
• Forms a thin, dry film
• Won't attract dirt or dust
• Resists extreme moisture
Applications:
• For use on wire ropes and cables, metal links and chains
Chain Lube
Part #74119 – 17.75 oz.
(Penetrating lubricant)
Unique foaming formula allows for super penetration without "sling off", even at high speeds.
Affords full protection for metal-to-metal moving parts. Material will not fly off or break down and is
recommended for any climatic conditions.
Features:
• Lubricates and penetrates
• Withstands high and low temperature changes
• Repels dirt and sand
• Extends chain life by reducing friction
• Resists "sling off"
Applications:
• Excellent for use on chain saws, sprockets, cutter bars, clippers, link and roller chains, etc.
• Increases chain and sprocket life by reducing friction.
30
30.64
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Lubricants
Dielectric Grease
Part #74439 – 3 oz.
(Silicone compound improves connections)
Silicone compound designed to provide excellent dielectric and lubricating properties for electrical
connections. Also ideal for use as an o-ring lubricant. Wide temperature range of -40oF to 500oF.
Features:
• High dielectric strength of 400 volts/mil prevents voltage
leaks, insuring superior performance in ignition systems
and electrical applications
• Excellent lubricant for rubber, plastic and ceramics
making installations faster, easier and more efficient
• High water and oxidation resistance prevents corrosion
in even the most extreme environments
• Radiation resistant for use around radiation equipment
and microwaves
Applications:
• Use in electrical terminals, lubrication and sealing of
rubber, o-rings and brass components and can also be
used for lubrication of plastic threads and gears.
SPECIFICATIONS:
Color ........................................ Translucent White
Temperature Range ....................... -40oF to 500oF
Penetration, unworked............................. 190-220
Worked 60 maximum
Bleed, 24 hrs/200oC (392oF) ........................ 260
Percent maximum............................................ 2%
Melting point ............................................. no melt
Specific gravity @ 25oC (77oF) ...................... 1.05
FDA Recognition, 21 CFR 175.3000 ...............yes
Electrical Dielectric Constant @ 100 Hz ....... 2.80
@ 100 kHz ...... 2.80
Dissipation factor @ 100 Hz ....................... .0006
@ 100 kHz ..................... .0005
Dielectric strength, volts/mil, 50 mil gap ......... 400
Volume resistivity, ohm-cm @23oC (73oF) 1 x 1015
Arc resistance, seconds ................................. 118
Clear Lube
Part #74137 – 13 oz.
(Transparent, high pressure lubricant)
Unique, transparent grease resists high temperatures and pressures while providing superior
lubrication and corrosion protection. Operating temperature range of -35oF to 530oF.
Features:
• Transparent formula – Superior lubrication
• High adhesive strength
• Resists "wash-out"
• Prevents corrosion
• 360o valve sprays at any angle
Applications:
• Ideal for use on door hinges, open gears,
wire ropes and cables, chains, sprockets
and anywhere conventional greases or
lubricants are used.
Zoom Spout Oiler
®
Part #74255 – 4 fl. oz.
30
(Premium grade, all purpose, turbine grade, lubricating oil)
The finest all purpose oil. Telescoping spout reaches everywhere.
Features:
• Flexible telescoping spout with
7'' extension for difficult to reach areas
050114
Applications:
•
•
•
•
•
Rotating equipment
Reciprocating equipment
Bearings
Motors
Slides
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.65
Lubricants
Lithium Grease White – Cartridge
Part #74428 – 14 oz.
(Premium grade industrial grease)
Specially designed to meet the ever-increasing requirements for high film strength, higher operating
temperatures, greater stability and longer lubricant life. The tough protective film ensures superior
lubrication and extended lubrication intervals. This shear stable, noncorrosive, extreme pressure,
water resistant lubricant is used for both plain and anti-friction bearings, gears, cams and slides.
It is also highly recommended as a bearing lubricant for electrical motors, spindles and other
mechanical devices when low torque, moderate speeds and long life are essential.
Features:
• Anti-Corrosive • Non-Staining • Water Resistant
• Superior Performance at Temperatures of 0oF to 325oF
• Extreme Pressure 65 Lb. Timken Load • EP Additives
Applications:
Ideal for use on:
• Wheel Bearings • Chassis Points • Ball Joints
• Slides • Rollers • Hinges • Small Gears
• Overhead Tracks • Construction Equipment • Mining
• Logging • Marine Applications • Industrial Applications
SPECIFICATIONS:
Drop Point (ASTM D-2265) ... 390oF (199oC)
Specific Gravity......................................0.95
Density (lb./gal.).......................................8.1
Temp. Range .0oF to 325oF (-18oC to 163oC)
Timken EP Test
(ASTM D-2509) ................. 65 lbs., Typical
Base Oil Viscosity .............. ISO 220, Typical
NLGI Rating ................................................2
Meets or exceeds requirements of U.S. Military Specification MIL-G-18458B (SH).
High-Temp Grease – Cartridge
Part #74422 – 14.5 oz.
(High temperature, high purity, synthetic lubricant)
A superior quality, high-performance synthetic grease specially formulated for extremely high
temperature applications. Assures minimal friction and maximum corrosion protection. Ideal for
all high temperature applications requiring superior lubricity and long service life. USDA accepted
for use in federally inspected meat and poultry plants. USDA accepted Classification H1.
Features:
• High-purity synthetic grease
• Extremely effective in high temperatures
• Resists water, acids, alkalis and salts
• USDA accepted
• Waterproof
Applications:
• Ideal for all high temperature
applications requiring superior
lubricity and long service life
30
30.66
SPECIFICATIONS:
Temp. Range ......-65oF to 500oF (-54oC to 260oC) Continuous
.............................-65oF to 550oF (-54oC to 288oC) Intermittent
NLGI Grade (ASTM D1092) ...................................................2
Timken OK Load (ASTM 2509) ..................................... 40 lbs.
Dropping Point (ASTM D566) .................................... Non-melt
Shelf Life...................................................................>10 years
Color ............................................................ Translucent White
Odor................................................................................. None
Penetration, Unworked (ASTM D217) .....................280mm/10
Four Ball EP Test (ASTM D2596)
Load Wear Index .................................................... 42.53 kg
Weld Point ................................................................. 200 kg
Four Ball Wear Test (ASTM D2266) Scar Dia. ............0.50mm
Salt Spray Test (ASTM B117) ...........................................Pass
Dielectric Loss (ASTM D924) ....................................1.2 x 1012
Dielectric Resistivity (ASTM D1169) ..........................1.7 x 1014
Dielectric Constant (ASTM D924) .......................................2.5
Oil Separation (ASTM D1402) ......................................... None
Evaporation Loss (ASTM D972) 22 hrs @ 212oF (100oC) <1%
Oxidation, Stability 100 hours (ASTM D942) ....................Pass
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Lubricants
Low-Temp Grease – Cartridge
Part #74420 – 14.5 oz.
(Low temperature, high purity, synthetic lubricant)
A superior quality, high-performance synthetic grease specially formulated for extremely low
temperature applications. Assures minimal friction and maximum corrosion protection. Ideal for
all bearing, chassis and equipment applications in low to medium temperatures. Also excellent
for use in and on refrigeration / freezer units. USDA accepted Classification H1.
Features:
• High-purity synthetic grease
• Effective in extremely low temperatures
• Resists water, acids, alkalis and salts
• USDA accepted
• Waterproof
Applications:
• Ideal for all bearing, chassis and
equipment applications in low to
medium temperatures
• Also excellent for use in and on
refrigeration / freezer units
SPECIFICATIONS:
Temp. Range ......-65oF to 300oF (-54oC to 149oC) Continuous
.............................-65oF to 400oF (-54oC to 204oC) Intermittent
NLGI Grade (ASTM D1092) ...................................................2
Timken OK Load (ASTM 2509) ..................................... 40 lbs.
Dropping Point (ASTM D566) .................................... Non-melt
Shelf Life...................................................................>10 years
Color ............................................................ Translucent White
Odor................................................................................. None
Penetration, Unworked (ASTM D217) .....................280mm/10
Four Ball EP Test (ASTM D2596)
Load Wear Index .................................................... 42.53 kg
Weld Point ................................................................. 200 kg
Four Ball Wear Test (ASTM D2266) Scar Dia. ............0.50mm
Salt Spray Test (ASTM B117) ...........................................Pass
Dielectric Loss (ASTM D924) ....................................1.2 x 1012
Dielectric Resistivity (ASTM D1169) ..........................1.7 x 1014
Dielectric Constant (ASTM D924) .......................................2.5
Oil Separation (ASTM D1402) ......................................... None
Evaporation Loss (ASTM D972) 22 hrs @ 212oF (100oC) <1%
Oxidation, Stability 100 hours (ASTM D942) ....................Pass
Dry Lube Plus
Part #74099 – 12 oz.
(A greaseless, high performance lubricant that dries to a non-oily film)
Ideal for use on delicate mechanisms; will not build up and resists attracting dust and dirt.
Features:
• 4-in-1 action makes it highly versatile
- Penetrates, lubricates, displaces moisture and prevents light corrosion
• The next generation chemistry contains no chlorinated solvents or ozone depleters
• Flash point 175°F with CO2 propellant and a 360° spray valve for easy use in any position
• Non-aggressive formula is safe for use on most plastics and painted surfaces
• Nonconductive to 38,000 volts for use around live equipment
• Meets or exceeds MIL-C-23411A - Paragraph 3.1.1, and 3.2-3.11
Applications:
• Excellent choice for virtually any general-purpose need
• Additional uses include high heat environments (up to 500°F) including use as a
release agent in molding processes
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.67
30
Lubricants
Moly Dry Lube
Part #74123 – 14 oz.
(High temperature, high pressure, dry film lube)
A thin, quick drying film gives long lasting protection to all moving and sliding parts. Reduces
friction at all contact points preventing galling, seizing and metal-to-metal wear. Protects
surfaces from moisture, rust, corrosion and also resists attack by oil, grease, water, most
chemicals and acids.
Features:
• Lubricate and protects
• High pressure lube 200,000 psi
• Wide temperature range -100oF to +700oF
• Waterproof and dustproof
• Super slick
• Non-corrosive
Applications:
• Used to protect all moving and sliding parts
• Use when lubrication is essential in
tight fitting, high temperature and high
pressure applications
Penetrating Oil with Graphite
Part #74101 – 14.75 oz.
(Frees rusted parts)
Penetrates deeply to free countersunk threads and prevent breakage of frozen parts. Cuts rust,
red or white lead, tar, dirt, grease, deposits of carbon, graphite, etc. Will not harm basic metals,
rubber or paint.
Features:
• Frees rusted nuts and bolts in seconds
• Prevents oxidation
• Resists salt water corrosion
• No water wash-out
• All position valve
Applications:
• Used for freezing frozen metal parts,
lubricating air driven tools, dismantling
equipment and removing broken taps
and dies.
Pneumatic Tool Anti-Seize Lubricant
(Superior lubricant for oilers in pneumatic lines)
Part #974375
32 fl. oz.
Formulated to meet the special requirements of industrial, household and agricultural tools.
It absorbs water and eliminates ice buildup and frost in air tools. A blend of rust and corrosion
inhibitors and a special base fluid oil minimizes tool wear and allows operation of air tools at
temperatures as low as -40oF. Works on all types of pneumatic equipment and gives worn
tools new life.
30
Features:
• Wide temperature range -40oF to 350oF
• Prevents rust and corrosion
• Less friction, wear, heat and noise
• Protects against corrosion
• Absorbs moisture, eliminates ice buildup and frost in air tools
Applications:
Ideal for use on:
• Air Impact Tools • Drills • Grinders • Screwdrivers • Sanders • Percussion Tools
• Household Shop Tools • Air Line Lubricators • All Air Tools Using Oil Lubrication
30.68
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Lubricants
Pro Pull Wire Pulling Lube
Part #74421 – 32 fl. oz.
TM
(Superior lubrication for wire and cable pulling, dries clean, food grade)
An exclusive formulation that provides a clean, super-slick surface allowing cable to be pulled
with minimum friction. Compatible with polyethylene, polypropylene, PVC, neoprene and
polyurethane cable jacketing materials used in the manufacture of power, telephone and fiber
optic cable. This non-staining formula evaporates completed, leaving no messy residue. Can
be used in temperatures as low as -13oF (-25oC). USDA accepted for use in federally inspected
meat and poultry plants. Classification H1.
Features:
• Superior lubrication for all wire
pulling applications
• Performs in extreme temperatures
• Coats evenly
• Dries clean and tack free
• Compatible with most materials
Applications:
• Used in the installation of power,
telephone and fiber optic cable
SPECIFICATIONS:
Characteristic
A)
B)
C)
D)
E)
F)
G)
H)
I)
J)
K)
Expansion
Viscosity
Color/Appearance
Separate
Coating Factor
(Cling Factor)
a) Vertical
b) Horizontal
Rate of Evaporation
% / Minute
Coefficient of Friction
a) Static
b) Dynamic
Residue (% Solids)
pH
Flammability
Compatibility with
Cable and Conduit
Materials
Temp Stability
80oC/24 hours
Room Temp.
(21oC)
Transient 4.5%
Estimated 10% dec.
Orange/Clear
None
None
Orange/Clear
None
50-57%
52-60%
61-65%
64-69%
0.0874
0.0521
0.0140
0.096
6.80 +/-0.1
6.80 +/-0.1
Nonflammable
No Incompatibility
Demonstrated
0.075
0.070
6.80 +/-0.1
6.80 +/-0.1
Nonflammable
No Incompatibility
Demonstrated
PTFE Dry Lube
Part #74116 – 11 oz.
(Multi-purpose dry lube and release agent)
Cryogenically processed PTFE coats surfaces quickly and easily. Resistant to virtually all
chemicals and solvents. Ideal for use on all machine parts and textile equipment as a
universal, dry non-staining lubricant. Excellent as a release agent for rubber, nylon, foams,
acrylics, plastic, polyurethane, plaster, filament windings, epoxies, metal molds, phenolics,
prepreg fabrication, polystyrene, encapsulating, epoxy potting and rubber molding. Safe for
use on most metal, plastic, wood, glass, rubber and paper.
Features:
• Dry, non-staining lubricant
• Excellent release agent
• Ideal for use on machine parts
• Effective from -40oF to +500oF
• Does not attract dust
30
Applications:
• Ideal for use on all machine parts and textile equipment as a universal, dry non-staining
lubricant.
• Excellent as a release agent for rubber, nylon, foams, acrylics, plastic, polyurethane, plaster,
filament windings, epoxies, metal molds, phenolics, prepreg fabrication, polystyrene,
encapsulating, epoxy potting and rubber molding.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.69
Lubricants
Red Grease Hi-Temp
Part #74415 – 11 oz.
(All-purpose, water washout resistant lube)
A multi-purpose lubricant that provides extra protection under extreme pressures. Resists
thinning under high pressure and returns to a thick, gel-like consistency after exposure to high
temperatures. This product is waterproof, making it ideal for exposed bearing hinges, cables,
pulleys, gears, linkages and springs. Working temperature range -40oF to +575oF.
Features:
• Multi-purpose heavy duty lubricant
• Resists water, acids, salts and alkaline chemicals
• Effective at high temperatures
• Penetrates as a liquid
• Congeals to a thick grease
Applications:
• Used on all bearings, motors shafts,
roller chains, hitches, bearing surfaces,
cables, pulleys, hinges, rollers, cams,
couplings and bushings.
Red Grease II – Cartridge
Part #74402 – 14 oz.
(All-purpose, high temperature, extreme pressure grease)
An all purpose non-melt grease especially formulated with extreme pressure and anti-wear
additives to provide heavy duty service. It is one of very few greases able to withstand heavy
shock load and impact pressures of 65 Timken load capabilities. Red Grease II has excellent
adhesive and cohesive properties. It resists most acids, weather, dirt, salts, spray, steam and
oxidation. Our product protects equipment indoors or outdoors even under high temperatures
and heavy loads. Penetration is 250-270 (ASTM D-217).
Features:
• All purpose heavy duty lubricant
• Resists water, acids, salts, rust and alkaline chemicals
• Non-melt – effective at temperatures of up to 550oF
• Load carrying capabilities: 65 Timken Load
• NLGI 2 to 2.5
Applications:
Ideal for indoor and outdoor equipment used in:
• Automotive • Farms • Bottling Plants • Cotton Gins • Sugar Cane Mills
• Dairies • Paper Mills • Industrial • Marine • Oil Fields • Steel Mills
• Air Conditioning • Elevators • Textile Plants • Construction • Mining
• Aircraft • Lumber Mills • Cement Plants • Food Plants • Sewage Plants
Red Grease III
(All-purpose, high temperature, extreme pressure grease)
30
Part #74404 – 7 lbs.
Part #74408 – 45 lbs.
Part #74410 – 120 lbs.
An all purpose heavy-duty non-melt lubricant specially formulated with extreme pressure
and anti-wear additives. Red Grease III has excellent adhesive and cohesive properties. It
resists and protects indoor and outdoor equipment from most acids, weather, dirt, salts, steam,
oxidation, high temperatures of up to 550oF, heavy loads and impact pressures of 65 Timken
load capabilities. Penetration is 250-270 (ASTM D-217).
Features:
• All purpose heavy-duty lubricant
• Resists water, acids, salts, rust and
alkaline chemicals
• Non-melt – effective at temperatures
of up to 550oF
• Load carrying capabilities:
65 Timken Load
• NLGI 2 to 2.5
30.70
Applications:
Ideal for indoor and outdoor equipment used in:
• Air Conditioning • Aircraft • Automotive
• Bottling • Cement • Construction
• Elevators • Farms • Food • Industrial
• Lumber • Marine • Paper • Sewage • Steel
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
090114
Lubricants
Silicone
Part #74108 – 12 oz.
(All-purpose lubricant)
Red Lion Silicone prevents freezing and eliminates sticking on doors, windows, locks and
latches. Lubricates and prevents sticking on conveyors. Lubricates without gumming and will
not stain or bind. Protects and waterproofs wiring. Helps prevent electrical losses. Aids in
preventing rust on chrome, electrical systems, switches, and helps prevent corrosion on
batteries. Authorized by the USDA for use in federally inspected meat and poultry plants.
Classification H1.
Features:
• Eliminates squeaks and sticking
• Lubricates, preserves and insulates
• Rustproofs and waterproofs
• Prevents freezing
Applications:
• Can be used on doors, windows, locks
and latches
• Excellent for use on rubber
• Protects and waterproofs wiring
• Prevents sticking on conveyors
Super Impact Grease – Cartridge
Part #74400 – 14 oz.
(Multi-purpose, extreme pressure and impact resistant grease)
This multi-purpose grease is fortified with special additives enabling it to withstand the heavy
impact and pounding common with heavy equipment. Our special additive package allows the
grease to stay in place and not spatter or pound out of the bearing or fitting.
Features:
• All-purpose heavy-duty lubricant
• Resists water, acids, salts and alkaline chemicals
• Non-melt – effective at temperatures up to 550oF
• Load carrying capabilities 65 Timken load
• NLGI 2
• Temperature range 0-425oF
Applications:
• Chassis • Wheel Bearings • Bearings • Motors • Shafts
• Automotive and Industrial Equipment
TFG Grease – Cartridge
Part #74406 – 14 oz.
(Multi-purpose, Teflon® fortified, extreme pressure & impact resistant grease)
A multi-purpose grease specially formulated to operate in extreme conditions of heat,
moisture, acid and alkali. Fortified with PTFE, provides added protection against shock loads
and impact pressures. By preventing metal-to-metal contact and supplying added lubricity and
slipperiness, this product will substantially reduce friction and wear.
Features:
• Multi-purpose fortified with PTFE
• Operating temperature 0oF to 400oF (intermittent to 450oF)
• Resistant to moisture, heat, acid and alkali
• Will not melt or run out regardless of temperature
• Excellent water resistance and metal adhesion
Applications:
• Added lubricant protection from very low to high temperatures makes this non-melt,
water-resistant grease perfect for ball and roller bearings, wheel bearings, king pins,
cranes and sleeve bearings.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.71
30
Lubricants
White Grease Lubricant
Part #74104 – 14 oz.
(Multi-purpose, H1 lithium lubricant)
Clings to bearing and gear surfaces and is highly resistant to "sling-off". Provides antirust and moisture barrier. Will not stain or discolor. Covers a wide temperature range from
35oF to 270oF. Authorized by the USDA for use in federally inspected meat & poultry plants.
Classification H1.
Features:
• Superior anti-rust and moisture barrier, and is effective over a wide temperature range
• Non-staining
• Won't wash or sling off
• Classification H1
Applications:
• Ideal for bottling, canning, packaging, conveyor, automotive and construction equipment
• Extremely effective on latches, hinges, striker plates, pulleys, chains, etc.
White Grease
(Multi-purpose lithium lubricant)
Part #74100 – 11 oz.
This products is white lithium grease in a convenient, easy-to-use aerosol can. It is an
exceptional coating for the prevention of rust and corrosion. In addition, this PTFE fortified,
durable, nonstaining lubricant provides superior friction reduction between similar or different
materials than other competing brands. Will not run, wash off, or freeze and does not gum
or cake. Use this product on battery terminals, brake cables, distributor caps, latches, hinges,
bolts, locks, antennas, equipment, tools, tracks, glides, bearings, rollers, buckles, shackles,
winch gears, and other external moving parts or exposed surfaces. This next generation
product is formulated without chlorinated solvents or ozone depleters.
Features:
• Superior anti-rust and moisture barrier
• PTFE fortified
• Non-staining
• Will not run, wash off, or freeze and does not gum or cake
Applications:
• Packaging industry, automotive field, marine and aircraft maintenance
• Ideal for battery terminals, brake cables, distributor caps, latches, hinges, bolts, locks,
antennas, equipment, tools, tracks, glides, bearings, rollers, buckles, shackles, winch gears,
and other external moving parts or exposed surfaces
30
30.72
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Lubricants
Cutting Oil III
Part #74172 – 16.75 oz.
(Lube for drilling, tapping and threading operations)
Special formula provides lubrication for faster, more convenient cutting operations and longer tool
life. Authorized by the USDA for use in federally inspected meat and poultry plants.
Features:
• Specially formulated lubricant provides a cleaner, smoother cut
• Effective on most metals
• Extends tool life
Applications:
• Specially formulated for all drilling, cutting, tapping and threading operations.
• Excellent on high strength and exotic metals. (Not for use on aluminum).
Toolube
TM
Part #74523 – 8 fl. oz.
(Cutting Tool Lubricant)
A specialized lubricant designed for tough metal-working operations on hard metals such
as stainless, high carbon, high chrome, nickel-chrome, heat-treated steels, cast iron, monel
and even non-ferrous metals like brass and aluminum. This compound contains no oil and
eliminates the difficult cleaning problems associated with white lead, molybdenum and similar
materials. It does not contain chlorine, fluorine, lead, sulfur, phosphorous, silicone, nitrates,
chromates, mercury or formaldehyde base compounds.
Features:
• For tough metalworking jobs
• Contains no oils
• Easy cleanup
• Environmentally safe
Applications:
• Ideal for use in drilling, tapping, sawing, spot facing, counterboring, milling, fly-cutting, seat
forming, engraving, broaching, drawing, piercing, punching, hole extruding and many other
applications
30
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.73
Lubricants
Tool Cool II
Part #74185 – 17 oz.
(Cutting Fluid)
Special formula provides a combination of lubrication and chemical cooling action for faster,
smoother cutting operations and longer tool life. Use for all drilling, cutting and tapping
applications. A must with high strength and exotic metals. Not for use on aluminum.
Features:
• Instantly lowers temperature – for faster cutting and longer tool life
• Unique lubricating properties – assures cleaner, smoother cutting
• Multi-purpose – for use in all drilling, tapping and threading applications
• Nonflammable – for increased safety
• Fast evaporation – minimizes clean-up
• Contains no 1,1,1-trichloroethane or ozone depleting chemicals – won't damage ozone
Applications:
• For use in all drilling, cutting and tapping operations
Cutting Wax
(Cutting Tool Lubricant)
Part #74559 – 2 oz.
Part #74560 – 16 oz.
Specially formulated multi-purpose cutting wax. For faster, smoother cutting operations and
longer tool life. Use for all drilling, cutting and tapping applications.
Features:
• Continuous shield against friction and heat
• Especially effective on stainless steel, aluminum and many exotic alloys
• Extends tool life and reduces chip welding
• Reduces tool costs and work piece scrap
• Provides a precision finish with closer tolerances on your finished work
• Nonflammable – for increased safety
Applications:
• For use in all drilling, cutting and tapping operations
30
30.74
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Lubricants
Anti-Seize
(w/Colloidal Copper Compound)
Part #74118 – 12.5 oz.
(Multi-purpose, threaded fastener lubricant, high temperature resistance)
The colloidal copper compound prevents seizing, galling and pitting under adverse conditions
of extreme temperatures and pressures. Provides excellent lubricity, assuring more accurate
torquing and easy disassembly of bolts, nuts, studs, etc. Protects parts from rust and
corrosion. Useful temperature range from -300o to 1,800oF.
Features:
• Prevents galling and seizing up to 1,800oF
• Seals and waterproofs threaded parts
• Prevents rust and corrosion
• Meets mil spec A-907(D)
Applications:
For use in the home and food and non-food areas of:
• Food Processing Plants • Schools • Warehouses • Office Buildings • Theatres
• Garages • Hotels • Motels • Kennels • Hospitals and Other Listed Areas
Anti-Seize Aluminum
(Multi-purpose, threaded fastener
lubricant, high temperature resistance)
Part #74423 – 6 oz. Pressurized Can
with Easy Applicator Top
Part #74425 – 16 oz. Brush Applicator Cap
This high quality lubricant depolymerizes and dissipates at temperatures above 400oF without
a carbon residue, having a dry film of aluminum and graphite to plate and protect metal
surfaces to temperatures of 1,800oF (980oC). It contains no lead or copper and has a synthetic,
non-melting carrier.
Features:
• Water resistant
• Prevents seizing and galling
• Reduces friction
• Protects against rust and corrosion
• Easy applicator top pressure can (P/N 74423) eliminates contamination of contents
– simply press to dispense
Applications:
• All threaded metal assemblies where anti-seize protection is desired. Use on
bolts, fittings, flanges, gaskets, keyways, nuts, plugs, studs, unions, valves, etc.
• Ideal for ovens, heat trolleys, kilns, stokers or any threaded parts exposed to
high temperatures.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30
30.75
Lubricants
Anti-Seize Pro-Lube
Aluminum/Copper Compound
Part #74424 – 3.75 oz.
(Brush Applicator Cap)
Aluminum/Copper Compound in a special semi-synthetic carrier. It leaves a protective film that seals and
protects metal parts even under extreme conditions, such as heat, pressure, steam and saltwater exposure.
Features:
• Heavy Duty Industrial-Strength
• Anti-Seize & Lubricating Paste
• Protects to +2000° F
• Reduces Torque
• Prevents Rust & Corrosion
• Excellent Lubricity
• Prevents Galling & Seizing
• Steam & Water Proof
• Chemical Resistant
• Extreme Pressure Lubricant
• Non-Melting
• Meets MIL SPEC MIL-A-907E
Applications:
For Marine, Metal Working, Oil Field, Automotive, Construction and Farm Work Applications, such as:
• Threaded Fittings
• Rig Drives
• Sprockets and Chains
• Casting Equipment
• Valve Shafts
Anti-Seize II – Copper Compound
(Brush Applicator Cap)
Part #74426 – 8 oz.
Part #74407 – 16 oz.
This blend of lubricating solids prevents seizing and galling of metal parts and threaded connections
exposed to harsh environments, high and low temperatures and other severe conditions. The active
ingredients are copper, graphite and a petroleum lubricant. Red Lion Anti-Seize II withstands pressure
conditions over 3,000 p.s.i. and is compatible with all metals and most plastics. It improves assembly
and disassembly. Allows reuse of damaged threaded parts and wil not harden, drop or separate.
Features:
• Protects against rust and corrosion
• Prevents thread damage, seizure, galling and heat-freeze up to 1,800oF (982oC)
• Enhances and protects most electrical connections
• Lowers friction
• Reduces torque
• Meets military specifications MIL-A-907
30
Applications:
• All nuts, bolts, bushings, centers, cam rollers, chains, slow moving bearings, compressors,
conveyors, couplings, dies, drills, drives, liftings, gaskets, gears, generators, joints, keyways,
motors, packings, plugs, press fits, pumps, shafts, sleeves, slides, spark plugs, studs, taps,
unions, valve stems, wristpins and more.
30.76
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Lubricants
C5-A® Copper Anti-Seize Stick – Copper
Features:
• Protect metal parts in high heat environments up to 1800oF
• Prevent rust, corrosion, seizing and galling
• Eases disassembly
• Reduce friction and wear to critical parts
• Buttery texture ideal for both coarse and fine threads
• Exceptional lubrication properties
Part #74565
0.70 oz. / 20 gm
Applications:
• Copper, brass, cast iron and all alloys, all plastics and all non-metallic gasket materials
• Bolts, bushings, pipes, fittings, flanges, gaskets, headers, manifolds, nuts, studs, etc.
• High heat ovens, crane assemblies, turbine studs, coal crushers, casting and molding
equipment and heat exchangers
Silver Grade Anti-Seize Stick – Silver
Features:
• Protects metal parts in high heat environments up to 1600oF
• Prevents rust, corrosion, seizing and galling
• Eases disassembly
• Reduces friction and wear to critical parts
• Buttery texture ideal for both coarse and fine threads
• Exceptional lubrication properties
Part #74566
0.70 oz. / 20 gm
Applications:
• Stainless steel and aluminum. Can also be used on copper, brass, cast iron and all alloys,
all plastics and all non-metallic gasket materials
• Bolts, bushings, pipes, fittings, flanges, gaskets, headers, manifolds, nuts, studs, etc.
• High heat ovens, crane assemblies, turbine studs, coal crushers, casting and molding
equipment and heat exchangers
Freezing Action Penetrant
Part #74556 – 9 oz.
(Frees rusted and frozen parts)
This product represents the latest breakthrough in penetrating lubricant technology. By combining rapid
freezing action with an advanced, rust eating formula, seized or rusted parts are easily released. Shrinkage of sprayed parts quickly breaks open micro fine fissures allowing the lubricant to easily penetrate
even the toughest rust. Red Lion Freezing Action Penetrant then dissolves rust making the job a snap and
future maintenance easier as well. This formula contains NO chlorinated solvents or ozone depleters and
is nonconductive to 33,000 volts for use around live equipment. The 360o spray valve allows for use in any
position and for access to hard-to-reach areas while the large pad actuator prevents freezing of fingertips.
This is an ultra-low VOC content product.
NOTE: Sudden temperature drop can result in "thermal shock" which may cause crazing of some plastics and paint. While appropriate
for use on many plastics and painted surfaces, always test in an inconspicuous area before general use. Accumulated vapors from this
product may reach ignition conditions in confined spaces. Always use with adequate ventilation.
Features:
• Advanced formula penetrating lubricant
• Freezing action breaks open rust barrier
• Innovative rust eating technology dissolves rust
• Nonconductive to 33,000 volts
• Ultra low VOC content – no chlorinated solvents – no ozone depleters
Applications:
• Ideal for use in the most demanding penetrating lubricant applications including rusted manifold
bolts, exhaust flanges, industrial, marine, farm, or other outdoor exposed equipment.
• Ideal for use in: factories, fleet maintenance centers, muffler shops, marine repair, and virtually
anywhere assembly/disassembly is performed.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.77
30
Lubricants
PAG 46
Part #74391 – 8 oz. / 236 ml
(A/C Lubricant)
For mobile air conditioning systems using R134a refrigerant. Do not use
this product in any other A/C systems. Use only in applicable compressors.
Features:
• Synthetic Refrigerant Oil (Polyalkylene Glycol) Plus Additives
• ISO Viscosity 46
• For R134a A/C Systems
• Premium Double End Cap
PAG 100
Part #74392 – 8 oz. / 236 ml
(A/C Lubricant)
For mobile air conditioning systems using R134a refrigerant. Do not use
this product in any other A/C systems. Use only in applicable compressors.
Features:
• Synthetic Refrigerant Oil (Polyalkylene Glycol) Plus Additives
• ISO Viscosity 100
• For R134a A/C Systems
• Premium Double End Cap
PAG 150
Part #74393 – 8 oz. / 236 ml
(A/C Lubricant)
For mobile air conditioning systems using R134a refrigerant. Do not use
this product in any other A/C systems. Use only in applicable compressors.
Features:
• Synthetic Refrigerant Oil (Polyalkylene Glycol) Plus Additives
• ISO Viscosity 150
• For R134a A/C Systems
• Premium Double End Cap
30
30.78
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Lubricants
PAG 46 With UV Dye
Part #74386 – 8 oz. / 236 ml
(A/C Lubricant)
For mobile air conditioning systems using R134a refrigerant.
Do not use this product in any other A/C systems. Use only in applicable compressors.
Features:
•
•
•
•
•
Synthetic Refrigerant Oil (Polyalkylene Glycol) Plus Additives
ISO Viscosity 46
For R134a A/C Systems
UV Dye For Leak Detection
Premium Double End Cap
PAG 100 With UV Dye
Part #74387 – 8 oz. / 236 ml
(A/C Lubricant)
For mobile air conditioning systems using R134a refrigerant.
Do not use this product in any other A/C systems. Use only in applicable compressors.
Features:
•
•
•
•
•
Synthetic Refrigerant Oil (Polyalkylene Glycol) Plus Additives
ISO Viscosity 100
For R134a A/C Systems
UV Dye For Leak Detection
Premium Double End Cap
PAG 150 With UV Dye
Part #74388 – 8 oz. / 236 ml
(A/C Lubricant)
For mobile air conditioning systems using R134a refrigerant.
Do not use this product in any other A/C systems. Use only in applicable compressors.
30
Features:
•
•
•
•
•
050114
Synthetic Refrigerant Oil (Polyalkylene Glycol) Plus Additives
ISO Viscosity 150
For R134a A/C Systems
UV Dye For Leak Detection
Premium Double End Cap
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.79
Lubricants
POE 100
(A/C Lubricant)
Part #74394 – 8 oz. / 236 ml
Part #74395 – 1 Quart / 32 oz. / 946 ml
For mobile air conditioning systems using R12 or R134a refrigerant. Do not use this
product in other A/C systems. Use only in applicable compressors
Features:
• Polyol Ester Refrigerant Oil
• ISO Viscosity 100
• For R12 and R134a A/C Systems
• Premium Double End Cap
POE 100
With UV Dye
Part #74389 – 8 oz. / 236 ml
Part #74390 – 1 Quart / 32 oz. / 946 ml
(A/C Lubricant)
For mobile air conditioning systems using R12 or R134a refrigerant.
Do not use this product in other A/C systems. Use only in applicable
compressors.
Features:
• Polyol Ester Refrigerant Oil
• ISO Viscosity 100
• For R12 and R134a A/C Systems
• UV Dye For Leak Detection
• Premium Double End Cap
30
30.80
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Paints and Coatings
Caterpillar ® Yellow
(Industrial protective coating)
Part #500644 Caterpillar® Yellow (Original)* – 15 oz.
Part #502311 Caterpillar® Yellow (New)** – 12 oz.
Caterpillar® Yellow (Original) – Used to restore original factory color
on farm tractors, implements and industrial or construction equipment.
Heat resistant to 300oF. Resists fading, chipping, cracking, and many
chemicals industrial gas, oil and grease.
Caterpillar® Yellow (New) – High solids for increased coverage and
low solvent level. Contains no lead, chromates or methylene chloride.
Protects against rust, weather and most chemicals.
Features:
• Environmentally formulated
• Lead free
• V.O.C. compliant
*Caterpillar® Trucks & Equipment
produced prior to 1979
**Caterpillar® Trucks & Equipment
produced after 1979
Applications:
• Color Coding
• Construction Equipment
• Motors
• Sheet Metal
• Tools
• Trucks
School Bus Yellow
Part #74146 – 16 oz. / 454 g
(Industrial protective coating)
A superior, lead-free industrial coating formulated for fleet maintenance applications where
maximum performance is required. For maximum protection, prime bare or rusted metal
surfaces with Pro-Coat™ Gray Primer, P/N 74003.
Features:
• Protects against rust, weather, oil, gasoline and most corrosive chemicals
• Resists abrasion and heat
• Withstands high humidity
• Capable of single coat hiding
Applications:
• For wood, metal, blowers, frames, machinery, racks, doors, and motors
30
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.81
Paints and Coatings
Satin Black Paint
Part #74011 – 15 oz. / 426 g
(Matches factory finish on many automotive exterior trim components)
Satin Black is formulated to match the OEM finish on many automotive exterior trim
components, and is designed for maximum adhesion on properly prepared surfaces without
the use of a primer. To achieve amazing results, clean surface with Red Lion™ Prep Solve
(P/N 74700), and remove loose paint and sand with 400 grit sandpaper.
Features:
• Protects against weather
• Contains No CFCs or Other Ozone Depleting Substances
Applications:
• Matches Factory Finish on Many Automotive Exterior Trim Components
Red Iron Oxide Primer
Part #74002 – 17 oz. / 482 g
(Industrial protective coating)
A superior grade primer formulated specifically for use with MRO Industrial Protective Coatings
to provide maximum performance under severe weather conditions or chemical exposure.
The high solids content ensures excellent adhesion, providing a smooth, even finish.
Features:
• VOC Compliant
• High Solids Content
• Environmentally Formulated
• Outstanding Corrosion Protection
• Protects Against Rust
Applications:
• For bare or rusted metal
30
No-Stick Welder's Anti-Spatter
Part #74018 – 18 oz.
(Protective spray coating for welding operations)
A non-flammable powder formulation that dries to a white film. Prevents welding spatter from
sticking to metal surfaces during welding. Just brush or wipe off residue after welding. Does
not contain silicone. Surface may be painted after use.
Features:
• Prevents spatter from sticking to metal surfaces
• Dries to powder film
• Brushes off after welding
30.82
Applications:
• For use in maintenance, production,
construction and body shops
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Paints and Coatings
PRO-COAT™ OSHA Color Industrial Enamels
(Extremely tough, corrosion resistant, fast drying, acrylic enamel paints)
Provide maximum coverage for marking and color coding pipe lines, electrical equipment,
safety equipment, emergency equipment, conduit, tools, motors, ducting and sheet metal.
The tough protective coating resists corrosion, chipping and peeling and our unique
SprayProTM nozzle makes application easy in both horizontal and vertical positions.
Features:
• One coat coverage
• Protects against rust and corrosion
• Use on metal and wood
• Leaves a durable, protective finish
• Dries fast
• SprayPro™ nozzle
Color Coding Applications:
Even though the Occupational Safety and Health Administration (OSHA)
has eliminated the specific color definitions and detailed requirements
for Safety Color Coding, the following suggested color scheme has been
utilized and accepted throughout the industry. The marking of physical hazards should never take the
place of eliminating those hazards when possible, and proper employee training in the recognition of
these colors and their respective warnings is imperative.
• RED is used to mark fire protection equipment such as alarm boxes, extinguishers, fire blankets and
doors, hose connections, hydrants and sprinkler piping. It can also be used on emergency stop bars
on hazardous machinery or stop buttons and electrical switches.
• YELLOW is used to color code dangerous materials such as flammable liquids, poisonous gases,
corrosive liquids (acids and alkalis) and steam, water or air at high temperatures and/or pressures.
It can also be used to highlight handrails.
• GREEN is used to color code relatively safe materials such as drinking water, service water, brine,
syrups or glycols. It can also be used to mark the location of First Aid equipment such as kits,
dispensary, stretchers and safety showers.
Part #74190 – Red
Part #74194 – Yellow
Part #74196 – Green
(All OSHA Paints 15.25 oz.)
VERTICAL
FANSPRAY
PATTERN
HORIZONTAL
FANSPRAY
PATTERN
050114
ROTATE
VALVE
NOZZLE 1/4
TURN TO
CHANGE
SPRAY
PATTERN
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30
30.83
Paints and Coatings
PRO-COAT Acrylic Enamel Paints
TM
(Extremely tough, corrosion resistant, fast drying, acrylic enamel paints)
Pro-Coat premium grade acrylic enamels provide the ultimate protection for all industrial
applications. Our fast-drying, high solids formula ensures maximum coverage and durability
on all metal and wood surfaces. The tough protective coating resists corrosion, chipping and
peeling and our unique SprayPro™ nozzle makes application easy in both horizontal and
vertical positions.
Features:
• Fast-Drying
• Maximum Coverage
• Ultimate Protection
• Interior / Exterior
• SprayProTM Nozzle
SprayPro™ Nozzle:
VERTICAL
FANSPRAY
PATTERN
HORIZONTAL
FANSPRAY
PATTERN
ROTATE
VALVE
NOZZLE 1/4
TURN TO
CHANGE
SPRAY
PATTERN
Applications:
• Conduit • Conveyors • Doors • Ducts • Fencing • Electrical Equipment • Ladders
• Machinery • Motors • Pipelines • Railings • Shelving • Tools • Safety Markings
Part #74014 (Gloss Black) – 15.25 oz.
Part #74010 (Gloss White) – 15.25 oz.
Part #74003 (Gray Primer*) – 15.25 oz.
Part #74016 (Hi-Temp Flat Black) – 15.25 oz.
Part #74012 (Industrial Gray**) – 15 oz.
*Use Gray Primer on bare or rusted metal
**Does not have SprayPro™ nozzle.
30
30.84
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Paints and Coatings
PRO-COAT Clear Epoxy Grit Coating
TM
Part #74024 – 12 oz.
(Extremely tough, corrosion resistant, fast drying, acrylic enamel paints)
This durable one-part epoxy coating is blended with non-slip grit for indoor or outdoor use.
Designed to give better traction in heavy traffic areas, under both wet and dry conditions.
Helps prevent slips and falls. Tough epoxy coating cures to a hard flat textured surface and is
chemically resistant to gasoline, oils, de-icing salts and more.
Features:
• Non-slip grit
• Prevents slips and falls
• Cures to a hard flat texture
• Chemically resistant
• Interior and exterior
Applications:
• Steps
• Walkways
• Cat Walks
• Ramps
• Spa/Swimming Pool Decks • Truck/R.V. Steps
• Wood Decks
• Handrails
• Sidewalks
• Loading Docks
• Locker Rooms
• Showers
• Public Restrooms
• Diving Boards
• Healthcare Facilities
• Marine Docks
• Agricultural Machinery
• Fiberglass
• Aluminum
• Concrete
• Industrial Work Places
PRO-COAT S/S Protective Coating
TM
Part #74040 – 15 oz.
(Extremely tough, corrosion resistant, fast drying, acrylic enamel paints)
Formulated with 100% type 316L stainless steel pigment. This unique formulation provides
maximum corrosion resistance on stainless steel, copper and other metals. It dries quickly to a
satin sheen, hardens overnight and cures to optimum strength in several days. It has excellent
high temperature resistance (400oF continuous, 450oF intermittent) and our unique SprayPro
valve makes application easy in both horizontal and vertical positions. Authorized by the USDA
for use in federally inspected meat and poultry plants.
Applications:
Features:
• Exhaust Systems • Steam Pipes
• Looks like stainless
• Mufflers • Radiators • Furnaces
• Contains real 316L stainless steel pigment
• Production Equipment • Engines
• Covers welding discoloration
• Plumbing Fixtures
• High temperature resistance
• Fast drying
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.85
30
Paints and Coatings
Non-conductive Paint - Glossy White
P/N 74029 – 16 oz.
(Maintains non-conductivity coating integrity)
Ideal for industrial applications.
Features:
• Single coat hiding power
• Resists fading, chipping, peeling, cracking, corrosion
• High opacity
• Great durability
• Lead-free formulation
Applications:
• Bucket Trucks, buckets, utility bodies, utility contractors, power companies,
fire departments, scaffolding coating, tops of ladders & hooks, power boxes
Ceiling Tile Spray – White
P/N 74134 – 15 oz.
(Restores damaged ceiling tiles)
Restores ceiling tiles damaged or discolored by smoke, water or aging. Easily applied and
dries in minutes. Makes tiles look like new.
Features:
• Restores discolored, smoke or water damaged tiles
• Eliminates costly tile replacements
• Easily applied – unique valve allows spraying tiles in place
• Dries quickly
SPRAYS
VERTICALLY!
Applications:
• Restores damaged ceiling tiles
Red Insulating Varnish
P/N 74139 – 16.25 oz.
(Protects and insulates motor windings and coils)
30
A superior high arc resistant coating assuring long lasting protection. Provides excellent
adhesion to windings, coils and metals. Has high dielectric strength of 50,800 volts/in.
(2 mil+ thickness).
Features:
• Impregnates and insulates motor windings, coils, electrical components, etc.
• Protects against oils, moisture, acids and alkalies
• High dielectric strength
• Dries quickly leaving a tough, flexible coating
• Seals out moisture on all electrical connection switches and panels
Applications:
• Bus Bars • Electrical Components • Field Coils • Motor Windings
• Rings and Frames • Stator Windings • Switchboard Parts • Transformers
30.86
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Paints and Coatings
Rust-Away Rust Conversion Coating
TM
Part #74157 – 32 oz.
Part #74555 – 1 gal.
(Flexible latex coating chemically converts rust to long lasting finish)
A flexible latex acrylic coating specially formulated for rusted metal surfaces. This water-based
formulation is easily applied like paint and stops rust dead in its tracks. It forms an airtight
protective seal, preventing air or moisture from coming in contact with metal, and it's weather
and chemical resistant.
Features:
• Chemically converts rust to a long lasting, weather-resistant coating
• No priming or sanding
• Won't crack, chip or peel
• Forms an airtight seal
• Flexible latex coating lasts for years
Applications:
• Protects transformers, coils, tools, fixtures, brackets, equipment, heavy machinery, chain link
fences and hundreds of other applications.
• Bonds to metal, wood, concrete and plastics without primers.
Rust-Away II Rust Converter
Part #74701 – 15 oz.
(Converts rust to a tough protective coating)
Specially formulated to convert rusted metal surfaces to a tough, black protective coating.
Forms an airtight protective seal, preventing air or moisture from coming in contact with metal.
Stops rust dead in its tracks. Weather and chemical resistant.
Features:
• Chemically converts rust to a long lasting, weather-resistant coating
• No priming or sanding necessary
• Won't crack, chip or peel
• Forms an airtight seal
• Paintable
Applications:
• Protects transformers, coils, tools, fixtures, brackets, equipment, heavy machinery, chain link
fences and hundreds of other applications.
30
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.87
Paints and Coatings
Cold Zinc Galvanizing
Part #74112 – 14 oz.
(Pure zinc spray for rust and corrosion protection)
Contains 93% pure zinc dust in organic resin for long lasting protection against rust and
corrosion. Manufactured to Mil Spec Mil-P-26915C. Use to rustproof and protect welds,
automotive and truck bodies, wrought iron, pipes, utility towers and vaults, gutters, structural
steel work and anywhere metal is subjected to corrosion.
Features:
• Prevents rust and corrosion
• 93% pure zinc dust
• Resistant to salt, corrosion and water
• Meets mil specifications
• Excellent primer
• Rustproofs welds
• Temperature to 400oF (600oF intermittent)
• Meets MIL specifications:
MIL-P-46105 Weld thru Primer
US Navy: Galvanizing Repair Specifications
MIL-P-21035
US Air Force: MIL-P-26915A for Steel
US Air Force: MIL-P-26433 for Towers
(Temperate and Arctic Zones)
Applications:
• Use to rustproof and protect welds, automotive and truck bodies, wrought iron, pipes, utility
towers and vaults, gutters, structural steel work and anywhere metal is subjected to corrosion.
Undercoat
Part #74129 – 18 oz.
(Rubberized coating that prevents rust and reduces road noise)
A black, rubberized undercoating for all automobile under surfaces. Sprays evenly and dries
completely to a smooth consistency. Can be top coated with automotive finishes.
Features:
• Prevents rust
• Reduces road noise
• Seals out water, fumes, road chemicals & dust
• Reduces lingering odor associated with under-coatings
• No "bleed through" when top coated
• No sagging
Snow Plow Coating
30
Applications:
• Panel & fender undersides
• Hoods & decks
• Trunk interiors
• Section repairs
• Weld joints
• Rust holes
Part #509280 – 1 Gal.
(Can be used on plow blades & all other snow removing equipment)
This coating deposits a thin, slippery layer of silicone that reduces friction on plow blades,
shovels and truck beds to provide more efficient plowing. It also protects metal surfaces from
rust and corrosion and will not wash off when cleaned after use.
CAUTION: Avoid application of coating material closer than 12" to 14" to the exhaust system or catalytic converter.
Features:
• Protects against rust and corrosion
• Reduces friction for more efficient plowing
• Leaves a hard, slippery layer of silicone on
plow blades
• Will not wash off
• Use less fuel
30.88
Applications:
• Just spray, brush, swab or roll onto
plow blades & other exposed metal and
painted surfaces.
• Protect equipment from rusting by applying
several applications after using
equipment and during summer storage.
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Paints and Coatings
Striping and Marking Paints
(Dependable performance in a wide range of marking applications)
These Striping and Marking Paints are formulated to address today’s environmental concerns
while providing efficient and dependable performance in a wide range of marking applications.
From utilities and construction to recreational and maintenance applications, we offer a striping
product suited to your needs.
• GOLF COURSE MARKER – a 16 oz. water-base marker for use on golf courses and other
porous applications. Formulated not to harm grass, this marker is not water-soluble and will
not wash away during rain or irrigation. This marker comes with the “Converta-Cap”,
a specially designed protective cover that does not need to be removed before using.
• ATHLETIC FIELD MARKER – A specially formulated 20 oz. water-base paint that will not
harm grass and is not water soluble for maximum durability.
• INVERTED TIP MARKER – A heavy-duty, 20-oz. water-base industrial marker. The no-clog,
fast drying formula is available in a full range of construction and APWA colors. This marker
also comes with the “Converta-Cap”. This provides the user with a convenient marking tool
without the worry of accidentally spraying. The new spray tip provides crisp lines up to 4'' wide
and approximately 250 feet in length.
• TRAFFIC MARKER – A 20-oz. water-base paint formulated with high pigment solids ideally
suited for a wide range of applications including concrete, blacktop, gravel or dirt. Not affected
by water.
Applications:
ATHLETIC MARKER PRODUCTS
For grass and turf applications
• Recreational School Fields
• Rental Yards
• Golf Courses
• Nurseries
• Paving Contractors
• Landscaping
• Home Landscaping Layouts
TRAFFIC MARKER PRODUCTS
For asphalt and concrete applications
• School Parking Lots and Playgrounds
• Apartment Complexes
• Churches
• Rental Yards
• Golf Courses
• Paving Contractors
• Water/Sewer Lines
• Hotels
• Public Works Municipal Projects
For applicator tools, see
Dispensing Equipment section
050114
GOLF COURSE MARKER
• Inverted-Straight Nozzle – 16 oz.
Part #74050 – White
Part #74051 – Red
ATHLETIC FIELD MARKER
• "T" Type Nozzle – 20 oz.
Part #74052 – White
Part #74053 – Orange
INVERTED TIP MARKER
• Inverted-Straight Nozzle – 20 oz.
Part #74004 – Purple
Part #74054 – White
Part #74055 – Flourescent Red
Part #74056 – Flourescent Orange
Part #74057 – Precaution Blue
Part #74058 – Alert Orange
Part #74059 – Safety Red
Part #74060 – Flourescent Green
Part #74061 – Flourescent Hot Pink
Part #74062 – Utility Yellow
30
TRAFFIC MARKER
• T-Type Nozzle – 20 oz.
Part #74063 – White
Part #74064 – Yellow
Part #74065 – Red
Part #74066 – Handicap Blue
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.89
Paint Removers
Prep-Solve
Part #74700 – 14.50 oz.
(Pre-paint surface cleaner)
Ideal for preparing surfaces prior to painting or bonding. This special formulation of virgin
solvents is extremely effective in removing adhesives, tar, undercoating, rustproofing, waxes,
teflon coatings, polishes, silicones, paint overspray, grease and sealants. The deep cleaning
action maximizes the adhesion of all paints, finishes and adhesives on all surfaces. Also ideal
for spraying on "tack cloths" for dust removal just prior to painting.
Features:
• Unique formulation – special blend of hydrocarbon solvents swiftly cut through a
wide range of dirt, grime and grease
• Leaves no film or residue – no additional cleaning required, does not inhibit the
application of primers, paints and other protective coatings
• Assures maximum adhesion – deep cleaning action significantly improves the adhesive
quality of glues and cements on surfaces to be joined.
Applications:
• Effective in removing adhesives, tar, undercoating, rustproofing, waxes, teflon coatings,
polishes, silicones, paint overspray, grease and sealants
• Excellent for preparing surfaces prior to painting or bonding
• Cleans fragile automotive surfaces such as carpeting, vinyls, plastics and fabrics
Gasket and Paint Remover
Part #74113 – 17.75 oz.
(Gasket, paint and decal stripper)
Fast acting spray that removes gaskets, paint, decals, dried oils, varnish, shellac and similar
coatings from any metal, wood, tile, brick, or concrete surfaces.
Features:
• Strong, fast acting formula
• Removes gaskets, paint, tar, adhesives
• Adheres to vertical surfaces
Applications:
• Can be used on metal, wood, glass, tile, brick, stone and concrete.
Do not use on plastic tile, lineoleum, or synthetic files.
30
30.90
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Paint Removers
Graffiti Wipes
(Removes Paint and Graffiti in One Easy Step)
P/N 74611
Net contents: 40
Used for fast, easy clean-up of paint from non-porous surfaces. These amazing wipes are
premoistened with an incredible cleaning formula that removes paints (including enamel),
ink and even permanent marker. A few swipes with a single wipe quickly dissolves away
unwanted paint and graffiti.
Product does not contain amyl acetate or methylene chloride, unlike other graffiti removers,
making these towels less hazardous for users as well as surfaces.
Features and Benefits:
•
•
•
•
Non-toxic when compared with other paint and graffiti removers
Environmentally safe and biodegradable formula
Abrasive yet non-scratching fabric aids in cleaning
Towels stay moist for greater usage and longer shelf life
Ideal for Use On Various Surfaces:
• Bathroom partitions
• Phone booths
• Lamp posts
• Bus stops and seats
• Trains
• Road signs
• Aluminum siding
• Stainless steel
• Wall tile
• Billboards
• Desks
• Lockers
Effective Against
• Paint
• Ink
• Enamel
• Permanent marker
Note: Product is NOT a hand cleaner. Protective gloves are recommended while using this product.
30
010115
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
30.91
Paint Removers
Graffiti Barrier
(High Performance Sacrificial Graffiti-Protection Barrier)
Graffiti Barrier is a clear, odorless liquid that can be applied to nearly any non-porous
surface to provide a protective barrier against graffiti. After it’s applied, it dries to a clear
film, which protects against spray paint, marker, pen and other substances. Once defaced,
the barrier is easily removed with no damage to the surface. The thickened formula adheres
to vertical surfaces, and is water-resistant, allowing for some outdoor applications. It will not
affect signs’ reflective properties, and will not yellow.
Features and Benefits:
• Creates a crystal-clear barrier to protect surfaces from graffiti
• Liquid formula can be applied to most any non-porous surface.
• Water-resistant formula
• Rinsable for easy removal and reapplication.
Protects Against:
• Spray paint
• Marker
• Pen
P/N 74625
Net contents: 1 qt.
P/N 74626*
Net contents: 1 gal.
P/N 74627*
Net contents: 5 gal.
P/N 74628*
Net contents: 55 gal.
* Non-stock item.
Please call for delivery.
Use on:
• Signs
• Lockers
• Restroom partitions
• Windows and mirrors
• Soda machines
• Doors
• Walls
• Surfaces that cannot be repainted
• Enamel
• Powder coated surfaces
• Electroplate
• Plastic
30
30.92
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
010115
Specialty Products
A&R Tabs
(A/C and Refrigeration Drain Pan Treatment Tablets)
Part #74720
6 Geltabs – for up to 5 tons
Part #74721
3 Geltabs – for up to 15 tons
New technology breakthrough for treating A/C and refrigeration drain lines and pans.
Easy to use – just place a tablet in the pan. As moisture drips on or flows over the tablet,
it activates the chemicals and locks it in place. A&R Tabs will never move and block the drain
line. They form a gel that slowly releases the active ingredients, producing up to 6 months of
safe, positive, prolonged cleaning action. Unlike liquid additives or cleaners that are difficult to
know when more additive is required, the A&R Tab provides a quick and easy visual indicator.
When the tablet is gone, it's time to replace it.
RED
YELLOW
Features:
• Locks into Place
• Slow and Continuous Release Gel
• Works Until Completely Dissolved
• Eliminates Odors from A/C and Refrigeration
Applications:
• Treating A/C and Refrigeration Drain Lines and Pans
Belt Dressing
Part #74117 – 14 oz.
(Revitalizes belts for longer life)
Ideal for rubber, canvas, industrial, automotive and other V-belts. Regular use adds life and
increases efficiency. A small amount applied to rubber and V-belts imparts maximum power.
On canvas belts, a slightly more liberal application is required.
Features:
• Stops slippage for maximum power
• Prevents "dry rot"
• Eliminates squeaking
• Revitalizes belts for longer life
Applications:
• Ideal for rubber, canvas, industrial, automotive and other v-belts
Drain Opener – Professional Strength
(Professional strength, clog busting power)
Part #74380
32 fl oz.
30
Provides extra clog busting power to open most stubborn clogs fast and easy,
even through standing water. Safe for plumbing fixtures, plastic pipes, grease traps,
septic tanks and cesspools.
Features:
• Dissolves hair, grease, lint, food and soap scum
• Clears tough clogs fast, even through standing water
• Safe for plumbing fixtures, plastic pipes,
grease traps, septic tanks and cesspools
Applications:
Ideal for use on: Sinks • Tubs • Showers • Grease Traps • Septic Tanks • Cesspools
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.93
Specialty Products
Chromagic
Part #28234 – 0.15 cu. ft.
(Spill Absorbent)
Chromagic is a non-selective product, it is one absorbent for multiple types of spills. Chromagic
is environmentally safe and friendly, non-toxic and non-flammable. It is highly absorbent.
In fact, it is 15 times more absorbent than clay based products. Easy to handle and lightweight,
it is 20 times lighter than clay based products. Chromagic is sold as a twin pack.
CAUTION: Cannot be used to absorb Hydrofluoric Acid (HF)
Features:
• Odor Free
• Instant clean up saves time
• One pound of Chromagic
can completely absorb
one quart of motor oil;
clay, earth, and sand
products require 15 pounds
• Meets or exceeds all OSHA
and EPA requirements
• Requires far less absorbent
to capture a spill
• Prevents accidents – Picks
up oily sheen, and reduces
Workers' Compensation
• Greatly reduced
disposal costs
• Will save money on shipping,
storing and disposal
• Lightweight and powerful
• Absorbs and holds
most liquids
• Works on all animal,
vegetable, mineral,
petroleum based or
semi-liquid spills
• Unlike kitty litter products
that contain “Crystalline”
Silica, Chromagic does not,
under OSHA standards,
qualify as a carcinogen, or
as a substance causing
silicosis, a lung disease
• Non-injurious to most
surfaces including
cement, asphalt, tile,
and carpet
Applications:
• Industrial Plants • Processsing Plants • Plumbing Contractors • Hospitals
• Nursing Homes • Day Care Centers • Athletic Clubs • Schools / Offices
• School Buses • Laboratories • Restaurants • Shopping Centers • Taverns
• Airlines • Cruise Liners • Public Transportation • Ambulance Services • Taxi Cabs
• Watercraft • Pet Stores • Kennels • Veterinarians • Jail Cells • Waste Haulers
Quik-Zorb™
Part #74189 – 16 oz.
(Spill Absorbent)
Absorbs over 100 times its weight of water-based spills with just a small sprinkle of powder.
Instantly "gels" all water-based chemical spills and human and animal bodily fluids including
blood, urine and vomit. Turns liquid biohazards into sweepable, flushable gel. Works on
hard surfaces and carpet. Deodorizes with a fresh mint odor counteractant fragrance. USDA
approved.
30
Features:
• Instantly gels and absorbs over 100 times its weight, allowing quick and easy cleanup of spills
• Fresh, deodorizing scent eliminates odors
• Biodegradable – can be flushed and disposed of easily
• V.O.C. compliant – contains no VOC's or ozone depleting chemicals
Applications:
• Industrial Plants • Processsing Plants • Plumbing Contractors • Hospitals
• Nursing Homes • Day Care Centers • Athletic Clubs • Schools / Offices
• School Buses • Laboratories • Restaurants • Shopping Centers • Taverns
• Airlines • Cruise Liners • Public Transportation • Ambulance Services • Taxi Cabs
• Watercraft • Pet Stores • Kennels • Veterinarians • Jail Cells • Waste Haulers
30.94
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Specialty Products
Gum Off
Part #74110 – 5 oz.
(Chewing Gum and Wax Remover)
For use on carpets, wood, tile, marble, Formica, terrazzo and cement surfaces.
May also be used on fabric, leather and vinyl furniture.
Features:
• Quick Freezing Action
• Hardens Gum and Wax
• No Chlorofluorocarbons
• Environmentally Compatible
Applications:
Carpets • Wood • Tile • Marble • Formica • Terrazzo • Cement Surfaces • Fabric
Leather • Vinyl
Snow & Ice Melter
P/N 74608 – 50 lb. box
P/N 74608P – Pallet (48 boxes)
(Remove Ice With Less Effort)
Red Lion™ Snow & Ice Melter granulars is a blend of 100% active ingredients (calcium chloride blend).
This unique formula has the added benefit of all materials working together in a synergistic fashion to
effectively melt snow and ice. Red Lion™ Snow & Ice Melter can be used on asphalt,
concrete, granite, tile, brick, bluestone, natural flagging, pavers and pave stone.
Features:
• Pink color to improve smooth and consistent coverage, especially during low visibility conditions
• Will not harm lawns, trees, or shrubs when used as directed
• Contains dust control and anti-caking agents
• Melts to -25°F
• Does not contain any rock salt
• Easy to apply by hand or spreader
• Safe for use in the State of California
Used by professionals for:
• Commercial buildings • Residential buildings • Campuses • Hospitals • Municipal buildings • Businesses
Applications:
• Parking lots • Driveways • Sidewalks • Steps • Porches • Patios
30
Ice & Frost Remover
Part #74488 –13 oz.
(Quickly dissolves ice, frost and snow deposits)
Specifically formulated to quickly dissolve ice, frost and snow deposits. Melts ice,
frost and snow instantly. Use on automobiles, trucks, buses, and maintenance equipment.
Features:
• Fast acting, water rinseable
• Helps prevent freezing when applied in advance
• Eliminates scraping and potential damage to glass
• Thaws frozen locks
• Works in any temperature
050114
100114
Applications:
• Windows
• Headlights
• Windshields
• Locks
• Tires
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
•
•
•
•
•
Tail lights
Hinges
Sidewalks
Steps
AC equipment
30.95
Specialty Products
Leak Stop
Part #74381 – 4 oz. / 114 g
(Seals leaks in auto A/C systems)
Seals leaks in auto air conditioners involving hoses, o-rings, and gaskets. For mechanical leaks,
a UV dye in the R-134a Leak Stop pinpoints the leak, so it can be repaired. Each can contains
two ounces of a mixture of PAG lubricant, seal additive and UV dye, plus two ounces of R-134a
refrigerant (1,1,1,2-Tetrafluoroethane). This product conserves refrigerant by allowing the A/C
system to be treated without having to open the system. R-134a Leak Stop may be used in all
R-134a A/C systems.
Features:
• With UV Dye For R-134a Systems
• Seals Leaks In Auto A/C Systems Involving Hoses, O-rings and Gaskets
30
30.96
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
TM
RESEARCH
EcoFriendly
Chemicals
Bio Lube "Lubricant/Penetrant"
A high performance penetrant and lubricating oil for general purpose use. Formulated with the
best optimized USA-grown natural seed oils and select additives, it surpasses the lubricity and
performance of conventional lubricants. Loosens rusty bolts, quiets squeaky hinges and moving
parts. For general purpose cutting, grinding and drilling metals, milling, tapping, and reaming.
Features
• Multipurpose lubricant and penetrant
• Loosens rusty bolts
• Quiets squeaky hinges and moving parts
• Deters water and protects from rust and corrosion
• General purpose cutting, grinding and drilling metals, milling, tapping, and reaming
Benefits
• Made from renewable USA-grown crop-based vegetable oils, better for your health
• Biobased/Biodegradable
• Reduces foreign oil dependence
• Multiple applications – Reduces product inventory
• Superior lubricity improves productivity
• Cooler operating and less smoke – Higher operating speeds
• Safe for all metals
• Will help your business comply with ISO-14000
• Does not contain chlorine
• High flash and fire points
P/N 74266 – Net wt. 2 oz.
P/N 74267 – Net wt. 8 oz.
30
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.97
TM
RESEARCH
EcoFriendly
Chemicals
These Red Lion™ Eco-Friendly "Green" Chemicals meet Green Seal™ Environmental Standards for
industrial and institutional cleaners and floor-care products.
In our continuing effort to offer the most environmentally preferable and effective products, we would like to introduce the new
Red Lion™ Eco-Friendly “Green” line of cleaners.
The products are designed to meet “Green Product” industry criteria. The standards encompass environmental impact, health
effects as well as product performance. They are Environmentally Preferable Products that are formulated to perform well yet
have no harmful effects on our environment or to the person using the product. We are proud to announce that Eco-Friendly
Multi-Purpose Cleaner, Eco-Friendly Glass Cleaner, Eco-Friendly Tub & Tile Cleaner, Eco-Friendly Peroxide Cleaner, Eco-Friendly
Zinc-Free Seal & Finish and Eco-Friendly Floor Stripper all meet specific Green Seal™ Environmental Standards.
There are laws already in place or are pending that will require the use of environmentally sensitive products in N.Y. State
Buildings, N.Y.C. Municipal Buildings and all schools in N.Y. State. Although New York has taken the lead in this area, other
states are sure to follow.
Perfect for use in schools, office buildings, apartment buildings, hospitals, nursing homes and other institutions where
environmentally preferred products are desired.
Eco-Friendly Multi-Purpose Cleaner
A highly concentrated, multi-purpose cleaner formulated to be a H.D. Cleaner, Spray and Wipe Cleaner
and a Neutral Floor Cleaner depending upon dilution. This product meets the requirements of the GS-37
Green Seal™ Standard. Provides top-tier performance for cleaning floors, walls, chrome, stainless steel,
table tops, vinyl, sealed wood and many other surfaces not harmed by water.
• Spray/wipe Cleaner: 1:128 dilution
1 gallon dilutes with water to make up to 512 quart bottles
• Heavy-duty Cleaner/Degreaser: 1:32 dilution
1 gallon dilutes with water to make up to 128 quart bottles
• Neutral Floor Cleaner: 1:256 dilution
Low suds, so it’s great for auto-scrubbers as well as mop buckets.
P/N 74067 (1 gal. Container)
P/N 74068 (5 gal. Pail)
P/N 74069 (55 gal. Drum)
Eco-Friendly Glass & Window Cleaner
30
A highly concentrated, glass, window and multi-purpose cleaner. It is designed to meet the requirements
of GS-37, the Green Seal™ Standard for Glass Cleaner. Eco-Friendly Glass & Window Cleaner has
been formulated with completely biodegradable surfactants and other naturally derived ingredients.
This non-toxic glass, window and multi-purpose cleaner provides top-tier performance. It is alcohol-free,
ammonia-free, non-streaking and fast drying.
• Glass & Window Cleaner: 1:64 dilution
1 gallon dilutes with water to make 256 quart bottles
P/N 74070 (1 gal. Container)
P/N 74071 (5 gal. Pail)
P/N 74072 (55 gal. Drum)
30.98
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
TM
RESEARCH
EcoFriendly
Chemicals
These Red Lion™ Eco-Friendly "Green" Chemicals meet Green Seal™ Environmental Standards for
industrial and institutional cleaners and floor-care products.
Eco-Friendly Tub & Tile Cleaner
A highly concentrated, non-corrosive, non-fuming, tub & tile cleaner. This product meets the requirements
of the GS-37 Green Seal™ Standard. It is formulated with a low pH organic salt capable of replacing a
wide range of traditional acids. Provides top-tier performance for cleaning tubs, tile, grout, walls, toilet
bowls, urinals, shower stalls and other bathroom surfaces.
P/N 74073 (1 gal. Container)
P/N 74074 (5 gal. Pail)
P/N 74075 (55 gal. Drum)
Eco-Friendly Peroxide Cleaner
A highly concentrated, multi-purpose cleaner providing top-tier performance as a Glass Cleaner, MultiPurpose Cleaner and a Restroom Cleaner depending upon dilution. Eco-Friendly Peroxide Cleaner
meets the requirements of the GS-37 Green Seal™ Standard. It has a pleasant orange scent.
• Spray/Wipe Cleaner: 1:128 dilution • 1 gallon dilutes with water to make up to 512 quart bottles
• Multi-purpose Cleaner: 1:64 dilution • 1 gallon dilutes with water to make up to 256 quart bottles
• Restroom Cleaner: 1:16 dilution • 1 gallon dilutes with water to make 64 quart bottles
P/N 74076 (1 gal. Container)
Eco-Friendly Floor Stripper
A concentrated, highly effective, fast acting, low odor, floor finish and wax remover – environmentally
benign but still strong enough to remove floor finishes and wax seals without the use of a floor machine.
Eco-Friendly Floor Stripper meets the GS-40 Green Seal™ Standard for Floor Stripper, based on its
reduced human and aquatic toxicity and reduced smog production potential. Using state-of-the-art
chemistry, it provides top-tier performance without the potentially harmful effects of 2-butoxyethanol,
ammonia, nonylphenol surfactants, dye or fragrance. A highly effective fast acting product with low
odor.
P/N 74080 (1 gal. Container)
P/N 74081 (5 gal. Pail)
P/N 74082 (55 gal. Drum)
30
Eco-Friendly Zinc-Free Seal & Finish
A highly effective, low V.O.C., zinc free floor seal and finish. Eco-Friendly Zinc-Free Seal & Finish represents
a new generation of floor care products. It exhibits a deep, wet-look gloss and it can be incorporated into
any floor maintenance program. It meets the GS-40 Green Seal™ Standard for Floor Finish. Eco-Friendly
Zinc-Free Seal & Finish contains no heavy metals, formaldehyde, ammonia or nonylphenol surfactants.
High levels of zinc have been found to be toxic to aquatic life.
P/N 74077 (1 gal. Container)
P/N 74078 (5 gal. Pail)
P/N 74079 (55 gal. Drum)
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.99
Chemicals
NS
AI
NO CFCs
W
CH
HI
NO CFCs
ET
ET
AY
ER
PL
DE
Red Lion™ Eco-Friendly Green Aerosols are toxin-free, petroleum distillate-free, VOC compliant,
and contain no ozone depleters. These products are also manufactured from environmentally safe,
naturally derived materials and packaged in recyclable containers that are made from partially recycled steel.
NT
RESEARCH
EcoFriendly
CO
TM
HE OZONE
L
What are bio-enzymatic products?
Many cleaners and industrial products contain toxins and chemicals which can cause harmful effects on the environment and human
health. Bio-enzymatic products contain strains of safe, naturally occurring bacteria and enzymes that are very efficient at breaking
down and digesting organic materials and eliminating soil and odor, and do not create pollution. Instead of using man-made chemicals
that use energy to produce and deplete natural resources, to clean and deodorize, Chromate uses nature’s approach.
What are renewable resources products?
These products are formulated from ingredients derived from renewable agricultural sources,including citrus and soy, and are
excellent alternatives to products made from traditional petroleum-based or synthetic components. Renewable resource ingredients
are constantly replenished by nature and help promote sound environmental stewardship since they don’t harm the environment
or expose the user to dangerous chemicals.
What are the benefits of using aerosols?
Aerosols can produce results unavailable from any other application method by controlling the particle’s size, spray pattern, volume
and concentration. This combination ensures that the proper amount and concentration of the product is delivered exactly where it’s
needed. Additionally, aerosols are packed in sealed containers, making them spill-proof, unlike liquid products. They reduce waste
because precise amounts of the product are delivered to an exact area. You can aim and spray exactly where you want to, with
maximum effectiveness. Products stay fresh because no air can get in the can, giving them a long shelf-life.
Eco-Friendly Cutting Oil
P/N 74084 – Net wt. 11 oz.
A multi-purpose, low odor cutting oil formulated from all natural ingredients for light-to-medium duty
applications. Keeps work pieces cooler and generates less smoke than petroluem-based cutting oils.
Suitable For:
• Cutting, Tapping, Threading, Sawing, Grinding
Features:
• Reduces heat distortion and tool burning, resulting in increased productivity
• Readily biodegrades
• Non-staining on all metals
• Specially designed for field and portable operations
Eco-Friendly Penetrating Oil
30
P/N 74083 – Net wt. 11 oz.
Contains no silicones or harsh solvents, which can affect plastics, lacquers, insulation and paint.
Forceful spray and powerful capillary action provides rapid penetration through rust and corrosion
to free frozen parts. Never-dry oil film lubricates parts, reducing friction and wear, to ensure free
and easy movement over a broad temperature range.
Suitable For:
Frozen Nuts and Bolts, Hinges, Screws, Clamps, Linkages, Fasteners, Molds, Lug Nuts, Tools,
Threaded Parts, Engine Parts, Motors, Bearings, Gears
Features:
• Contains no silicones or harsh solvents that can harm plastics, lacquers, insulation or paint.
• Forceful spray helps blast through rust and corrosion.
• Powerful capillary action rapidly climbs threads and penetrates into tiny voids to carry lubricant
to where its needed.
• Long-lasting, never-dry oil film provides excellent lubricity over a broad temperature range.
30.100
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Safe-T-Line
™
TM
Why Safe-T-Line™?
Simple . . . A growing concern for user-friendly, environmentally
sound products.
RED LION RESEARCH has addressed this issue by offering a line of aerosol products for the
industrial maintenance user. Appropriately named Safe-T-Line, they are less hazardous to the
user and less damaging to the environment, while still providing all the quality and performance
essential for those tough, demanding industrial applications.
Safe-T-Line™ products are safer for the user and the environment because it does not contain
harmful CFC's, chlorinated solvents, toluene or butyl. It is extremely low in V.O.C.'s and carries
a level 1 NFPA 30B fire code rating, (the safest storage rating for aerosol products).
➤ NO CFCs (Chlorofluorocarbons)
Chemicals linked to ozone depletion
➤ NO Chlorinated Solvents
Also linked to ozone depletion. Certain chlorinated solvents are suspected carcinogens.
➤ NO Perchloroethylene, Toluene or Butyl
Suspected carcinogens.
➤ OZONE-SAFE Propellant
Propellant has no harmful effect on ozone.
➤ LOW VOC’s (Volatile Organic Compounds)
Carbon-containing (organic) compounds created from sources such as automobile exhaust,
power plants, paints, etc. VOC’s can form ground level ozone, a major component of smog.
➤ NFPA 30B Level 1 Fire Code Rating
The National Fire Protection Association’s best rating for the safe storage of aerosols.
Kleen & Shine
Part #74127 – 16 oz.
(All purpose, stainless steel, food grade cleaner)
NO CFCs
W
CH
HI
CO
NS
AI
ET
ET
AY
ER
NO CFCs
PL
DE
Features:
• Cuts through stubborn greasel
• Cleans and polishes
• Fast acting
• No residue
• Will not scratch
NT
Kleen & Shine is an excellent fast-acting cleaner and polisher for stainless steel surfaces.
Works on contact at removing dust, dirt and grease. Authorized by the USDA for use in
federally inspected meat and poultry plants. Classification C1.
HE OZONE
L
Applications:
• For use on stainless steel, enamel, porcelain, ceramic tiles, refrigeration units, range hoods,
door handles and counter tops
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.101
30
Safe-T-Line
™
Engine Degreaser
Part #74183 – 15 oz.
(High pressure spray, water rinsing)
This natural citrus cleaner/degreaser is a powerful engine degreasing formula.
It cleans and degreases oil, dirt, grease, tar and adhesives.
Features:
• Superior formulation cuts through stubborn grease and oil
• High pressure spray
• Water rinsing
• Non-chlorinated
• Easy to use
Applications:
• For use on automotive engines, aluminum, stainless steel, tire whitewalls and garage floors
H.D. Citrus Cleaner/Degreaser
Part #74145 – 18 oz.
(Powerful citrus base, biodegradable cleaner)
H.D. Citrus Cleaner is a highly concentrated cleaner and degreaser with its powerful foaming
action actually lifts dirt and grease off surfaces so it can be easily wiped clean with a cloth.
Features:
• Natural citrus solvent
• Powerful foaming action
• Removes grease, oil and dirt from most surfaces
• Deodorizes with fresh citrus scent
• Biodegradable
Applications:
• For use on porcelain, formica, tiles, enamel surfaces, vinyl tops, floor mats, sinks, tubs,
appliances, tools and equipment, oil and tar stains, printing presses and white wall tires
Smoke & Odor Eliminator
30
Part #74158 – 12 oz.
(Encapsulates and destroys smoke and other tough odors)
Smoke & Odor Eliminator is scientifically formulated to destroy any and all odors safely and
effectively. It does not “mask” odors, it chemically bonds with the odor carrying molecules and
encapsulates them. Extremely effective on all airborne odors and as a surface spray.
Features:
• Chemically encapsulates and neutralizes odors
• Extremely effective for smoke and other tough odors
• Leaves a clean, fresh fragrance
Applications:
• Slaughter Houses
• Zoos
• Kennels
• Public Rest Rooms
• Transportation Industry
30.102
•
•
•
•
•
Locker Rooms
Garbage Areas
Sewerage Areas
Smoke Filled Rooms
Mortuaries
• Hotels
• Air Conditioning Filters
• Any area where objectionable
odors need to be eliminated
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Odor Eliminators
Air Sanitizer and Deodorizer
Part #74467 – 8.2 oz.
(Metered mist sanitizer – Eliminates odors and odor causing bacteria)
For automatic dispensers. The next generation odor counteractant system chemically bonds
with the malodor molecule destroying the odor source instead of just covering up or masking.
Excellent for control of even the toughest odors, including post-fire odors (cigar/cigarette smoke
treatment), protein decomposition odors from garbage, and fisheries.
Features:
• Low VOC chemistry is hydro-alcoholic
• No petroleum distillates or hydrocarbon propellants
• Ultra-dry spray has little fall out – Nonflammable
• 3000 sprays / lasts for 30 days – 24 hour basis / every 15 minutes
Applications:
• Public Rooms • Restrooms • Bathrooms/Showers • Pools/Spa Areas • Basements
• Storage Rooms • Kitchens/Cafeterias • Schools • Offices • Hotels • Casinos
• Hospitals • Nursing Homes • Prisons • Laundromats • Theaters • Auditoriums
• Railroad Cars • Heavy Truck Cabs • Airplanes • RVs/Campers • Boats • Cabins
• Beach Houses • Buses • Taxicabs • Game Rooms • Health Clubs • Fitness Centers
• Yoga Studios • Factories/Mills • Department Stores • Grocery Stores
Lemon Italian Ice Air Deodorizer
Part #74470 – 14 oz.
(Deliciously scented, finely atomized, micro-mist air freshener)
Provides complete deodorization of malodors in the air, on surfaces and on fabrics.
Features:
• Does not allow wetting, staining or messy fall-out
• Eliminates tobacco smoke, cooking odors, mold, and mildew odors
• Non-chlorinated
• V.O.C. compliant
• Chemically neutralizes malodors
• Dry spray particles
Applications:
• Locker rooms
• Hospitals
• Nursing homes
• Smoking areas
• Cars
• Boats / RVs
• Motels
• Restaurants
• Bathrooms
• Carpets
• Upholstery / Fabrics
• Draperies
Baby Powder Odor Eliminator
P/N 74166 – 14.75 oz.
(Odor destroyer with baby powder fragrance)
A unique product that chemically neutralizes malodors and leaves a fresh baby powder scent. Use
in locker rooms, hospitals, nursing homes, smoking areas, cars, boats, RV's, motels, restaurants,
bathrooms, on carpets, upholstery, draperies, fabrics or anywhere odor is a problem.
Features:
• Eliminates all odors
• Chemically encapsulates and neutralized odors
• Leaves a fresh baby powder scent
Applications:
• Locker Rooms • Hospitals • Nursing Homes • Smoking Areas • Cars • Boats • RV's
• Motels • Restaurants • Bathrooms • Carpets • Upholstery • Draperies • Fabrics
• Anywhere odor is a problem
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.103
30
Odor Eliminators
Smoke & Odor Eliminator
Part #74158 – 12 oz.
(Encapsulates and destroys smoke and other tough odors)
Smoke & Odor Eliminator is scientifically formulated to destroy any and all odors safely and
effectively. It does not “mask” odors, it chemically bonds with the odor carrying molecules and
encapsulates them. Extremely effective on all airborne odors and as a surface spray.
Features:
• Chemically encapsulates and neutralizes odors
• Extremely effective for smoke and other tough odors
• Leaves a clean, fresh fragrance
Applications:
• Slaughter Houses
• Zoos
• Kennels
• Public Rest Rooms
• Transportation Industry
•
•
•
•
•
Locker Rooms
Garbage Areas
Sewerage Areas
Smoke Filled Rooms
Mortuaries
• Hotels
• Air Conditioning Filters
• Any area where objectionable
odors need to be eliminated
Odor Neutralizing Fogger
Part #74468 – 6.75 oz.
(Removes offensive odors)
Finely atomized, micro-mist total release air freshener provides complete deodorization of
malodors in the air, on surfaces and on fabrics.
Features:
• Does not allow wetting, staining or messy fall-out • V.O.C. compliant
• Dry spray particles with unique scent
• Eliminates tobacco smoke, mold & mildew odors
• Non-chlorinated
Applications:
• Locker rooms
• Hospitals
• Nursing homes
• Hotels and motels
• Safe on fabrics (carpets, upholstery, draperies)
• Treats 6,000 cu. ft.
• Restaurants
• Smoking areas
• Cars, boats, RVs
• Public buildings
• Bathrooms
• Garbage containers
• Closets
• Laundry hampers
Fresh Linen Air Freshener
30
Part #74469 – 14 oz.
(For A Clothesline Fresh Fragrance)
Deliciously scented, finely atomized, micro-mist air freshener. Provides complete deodorization
of malodors in the air, on surfaces and on fabrics. Eliminates tobacco smoke, cooking odors,
mold, and mildew odors. Does not allow wetting, staining or messy fall-out.
Features:
• Non-chlorinated
• V.O.C. compliant
Applications:
• Locker rooms
• Hospitals
• Nursing homes
30.104
• Chemically neutralizes malodors
• Dry spray particles
• Smoking areas
• Cars
• Boats
• RVs
• Motels
• Restaurants
• Bathrooms
• Carpets
• Upholstery
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
• Draperies
• Fabrics
050114
Odor Eliminators
GreenWāv Natural
Odor Eliminators
Commercial Gel
Air & Surface Spray
P/N 74577 – 8 oz.
P/N 74576 – 32 fl. oz.
(Commercial Gel and Spray – Destroys odor on a molecular level)
Non-toxic GreenWāv natural odor eliminators effectively remove both organic and inorganic
malodors from the air, laundry, carpet, upholstery and other surfaces. Notice we did not say
mask odors! GreenWāv products chemically bond with odor causing molecules and
eliminate them completely without leaving a lingering fragrance. Made with natural, non-toxic
and biodegradable active ingredients. They are safe for use around people and animals in a
variety of settings/facilities.
Features:
Commercial Gel
• Eliminates odor in the air.
• The continuous release formulation works around the clock, providing 24/7 odor control.
• For combating persistent odor problems that may not be avoidable or correctable.
• Use Dispenser P/N 1820
Air & Surface Spray
• For rapid targeted odor control.
• Instantly bonds to and eliminates odor molecules in the air and those that have penetrated
and/or are resting on surfaces.
• Can also be added to mop buckets, humidifiers or fogging equipment for large areas.
Applications:
• Hospitals
• Nursing Homes
• Schools/Universities
• Hotels/Motels
• Offices/Warehouses
• Cafeterias
• Shopping Malls
• Theaters
• Fleet
• Maintenance Shops
• Garages
• Restaurants
• Health Clubs
• Sports Arenas
• Indoor Play Areas
Urinal Deodorant Screens
For fragrances and
P/Ns, see table below.
(Freshens Urinal for 30 Days – 15x more fragrance which is gradually
released over 30 days versus a vinyl urinal screen)
Releases billions of optimized bacteria that clean the urinal and eliminate odors.
Recommended by the #1 Manufacturer of waterless urinals – Falcon Waterfree Technologies.
Features:
• Complies with VOC requirements – available for
sale in all 50 states, North America & Europe.
Fragrance
P/N
Herbal Mint
74473
Honeysuckle
74474
• Saves Time & Money – Revolutionary design
reduces splash back while optimizing fragrance
release - cutting cleaning time by up to 50%.
Kiwi Grapefruit
74475
Fabulous
74442
Wintergreen
74476
Ocean Mist
74483
Mango
74477
Citrus
74478
Spiced Apple
74479
• Translucent Flexible Design – Allows full view
of urinal drain to ensure optimal drain flow while
trapping debris.
• Meets the “Purchase of Sustainable Cleaning
Products and Materials” criteria under the
LEED point management system.
Fragrance Intensity
U.S. Patent
#8,007,707
Additional patent pending
Color
30
Cotton Blossom 74480
Guava Pineapple 74481
Cucumber Melon 74482
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
30.105
Odor Eliminators
Metered Mist
(Long Lasting Concentrated Dry Spray Neutralizer for Dispensers)
Features:
• Neutralizes malodors
• Long lasting control
• Dry spray, no fallout
• Leaves a pleasant scent
• Non-Staining
• Non-Chlorinated
• No CFC’s
NO CFCs
NS
W
AI
CO
NO CFCs
ET
ET
AY
ER
Size
7.25 oz.
7.25 oz.
7.25 oz.
7.25 oz.
7.25 oz.
7.25 oz.
7.25 oz.
7.25 oz.
7.25 oz.
CH
HI
Part No.
74433
74434
74460
74461
74462
74463
74464
74465
74466
PL
DE
Description
Red Clover Tea
Cucumber Melon
Citrus Creme
Fruit Basket
Powder Fresh
Vanilla Delight
Pine Forest
Fresh Linen
Piña Colada
NT
For use in automatic dispensers. Delivers maximum fragrance and odor control with measured
releases. Finely atomized spray carries farther and lasts longer tan other leading brands.
HE OZONE
L
Use metered mist dry spray
neuralizer with the metered
mist dispenser, P/N 1817.
Applications:
Anywhere odor is a problem
• Bathrooms
• Locker rooms
• Hospitals and nursing homes
• Smoking areas
• Motels
• Restaurants
Metered Mist Variety Packs
Multiple scents bundled together in two easy-to-order "Variety Packs".
Variety Pack, P/N 200145
• Citrus Creme
P/N 74460
• Fruit Basket
P/N 74461
• Powder Fresh P/N 74462
• Vanilla Delight P/N 74463
• Pine Forest
P/N 74464
• Fresh Linen
P/N 74465
30
Part #74230 & 74225:
55 Gallon Drum
Part #74231 & 74226:
30 Gallon Drum
Part #74233 & 74228:
5 Gallon Pail
Part #74234 & 74229:
1 Gallon Container
(Buy 4 x 1 Gal)
Variety Pack II, P/N 200177
• Red Clover Tea
P/N 74433
• Cucumber Melon P/N 74434
• Citrus Creme
P/N 74460
• Fruit Basket
P/N 74461
• Powder Fresh
P/N 74462
• Fresh Linen
P/N 74465
Pleasant Scent™
(Chemically destroys toughest odors)
Part #74230-74234 – Lemon-Lime Scent
Part #74225-74229 – Green Apple Scent
A highly refined blend of chemicals designed to destroy odors of putrefaction, defecation,
regurgitation, urination and many other malodors. It is easy to apply with a trigger sprayer or
fogging unit and is biodegradable, phosphate free and nonflammable.
Features:
• Chemically destroys the toughest malodors
• Easy to use as an air or surface spray
• Does not mask odors
• Biodegradable
Applications:
• Hospitals/Laboratories • Mortuaries • Motels • Factories • Rest Rooms • Kennels
• Airplanes • Etc.
Instructions:
Use full strength or dilute with water. Dilutes up to 10:1.
30.106
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
050114
110114
Dispensing Equipment
Metered Mist Dispenser
TM
RESEARCH
Part #1817
Automatic wall mounted dispenser delivers maximum
fragrance and odor control with measured releases.
Finely atomized spray carries farther and lasts longer
than other leading brands.
EcoE
FFriendly
Chemicals
Red Lion™ 32 oz. Spray Bottles
For Eco-Friendly Chemicals
32 oz. Spray Bottle for Eco-Friendly
Multi-Purpose Cleaner
Meets the requirements of the GS-37
Green Seal™ Standard. Provides top-tier
performance for cleaning floors, walls,
chrome, stainless steel, table tops, vinyl,
sealed wood and many other surfaces not
harmed by water.
Red Lion™ Metered Mist
• Neutralizes Malodors
• Long Lasting Control
• Dry Spray, No Fall out
• Leaves a pleasant scent
• Non-Staining
• Non-Chlorinated, No CFC’s
P/N 74067B (32 oz. Bottle)
Use Anywhere
Odor is a Problem
• Bathrooms
• Locker rooms
• Hospitals
• Nursing homes
• Smoking areas
• Motels
• Restaurants
32 oz. Spray Bottle Eco-Friendly
Glass & Window Cleaner
Designed to meet the requirements of
GS-37, the Green Seal™ Standard for
Glass Cleaner. Eco-Friendly Glass &
Window Cleaner has been formulated with
completely biodegradable surfactants and
other naturally derived ingredients. This
non-toxic glass, window and multi-purpose
cleaner provides top-tier performance. It is
alcohol-free, ammonia-free, non-streaking
and fast drying.
Note: D-cell battery
required, not included.
P/N 74070B (32 oz. Bottle)
Dispenser Features
LED Indicator
CDS/Light
Sensor
Interval LED
Indicator
Metal Shelf
Support Bracket
Operates on
2 D-Cell Batteries
Mode Button
ON/OFF Switch
32 oz. Spray Bottle Eco-Friendly
Tub & Tile Cleaner
A highly concentrated, non-corrosive,
non-fuming, tub & tile cleaner. This product
meets the requirements of the GS-37
Green Seal™ Standard. It is formulated with
a low pH organic salt capable of replacing
a wide range of traditional acids. Provides
top-tier performance for cleaning tubs, tile,
grout, walls, toilet bowls, urinals, shower
stalls and other bathroom surfaces.
P/N 74073B (32 oz. Bottle)
32 oz. Spray Bottle Eco-Friendly
Peroxide Cleaner
A highly concentrated, multi-purpose
cleaner providing top-tier performance as
a Glass Cleaner, Multi-Purpose Cleaner
and a Restroom Cleaner depending upon
dilution. Eco-Friendly Peroxide Cleaner
meets the requirements of the GS-37
Green Seal™ Standard. It has a pleasant
orange scent.
P/N 74076B (32 oz. Bottle)
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.107
30
Dispensing Equipment
Red Lion™ Blend Mate Wall Dispensers
A mounted dispenser for automatic dilution/metering
of Eco-Friendly cleaners into secondary containers
(32 oz. bottle or bucket fill) in ready to use form.
P/N 1822 – Peroxide Cleaner Wall Dispenser
P/N 1824 – Multi-Purpose Cleaner Wall Dispenser
P/N 1826 – Glass & Window Cleaner Wall Dispenser
P/N 1828 – Tub & Tile Cleaner Wall Dispenser
Uses
Convenient wall mount in janitors closets,
housekeeping/maintenance rooms, etc.
Features
• Gray high density plastic cabinet
• Installation Materials Included:
Mounting hardware, water inlet
hose, 2 locking keys, appropriate
metering tips installed by the
factory according to product used.
• Cabinet Size:
22'' high x 6-1/2'' width x 7-3/4''
depth. Up to 4 cabinets can be
linked together with a single cold
water source.
Multi Purpose
Cleaner Dispenser
Glass & Window
Cleaner Dispenser
Tub & Tile
Cleaner Dispenser
Peroxide Cleaner
Dispenser
Available Types
Eco-Friendly Glass & Window Cleaner:
• 1 button
• 32 oz. bottle
• pre-set dilution
30
Eco-Friendly Multi Purpose Cleaner:
• 2 button
• 32 oz. bottle & bucket fill
• 3 dilution selector
Eco-Friendly Tub & Tile Cleaner:
• 2 button
• 32 oz. bottle & bucket fill
• 3 dilution selector
Eco-Friendly Peroxide Cleaner:
• 2 button
• 32 oz. bottle & bucket fill
• 2 dilution selector
30.108
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Dispensing Equipment
Red Lion™ Blend Mate
Wall Dispensers
Directions For Use
1. Hang cabinet on wall using mounting screws
provided, making sure water hose will reach
water source.
2. Connect black 6' water hose to upper right
side of dispenser cabinet and water source.
3. Using key(s) provided, unlock cabinet.
4. Remove cap from gallon bottle of concentrate
and place inside dispenser cabinet, inserting
draw tube into bottle.
5. Close and lock cabinet.
6. Following direction label on front of dispenser,
turn toggle switch to desired dilution strength.
Insert clear plastic fill tube into spray bottle or
mop bucket and push appropriate button to
activate flow.
TM
RESEARCH
EcoE
FFriendly
Chemicals
Use Blend Mate Wall Dispensers and
32 oz. Spray Bottles With The Following:
Eco-Friendly
Multi-Purpose Cleaner
Meets the requirements of the GS-37
Green Seal™ Standard. Provides top-tier
performance for cleaning floors, walls,
chrome, stainless steel, table tops, vinyl,
sealed wood and many other surfaces not
harmed by water.
P/N 74067 (1 gal. Container)
Eco-Friendly
Glass & Window Cleaner
Designed to meet the requirements of
GS-37, the Green Seal™ Standard for
Glass Cleaner. Eco-Friendly Glass &
Window Cleaner has been formulated with
completely biodegradable surfactants and
other naturally derived ingredients. This
non-toxic glass, window and multi-purpose
cleaner provides top-tier performance. It is
alcohol-free, ammonia-free, non-streaking
and fast drying.
P/N 74070 (1 gal. Container)
Eco-Friendly Tub & Tile Cleaner
A highly concentrated, non-corrosive,
non-fuming, tub & tile cleaner. This product
meets the requirements of the GS-37
Green Seal™ Standard. It is formulated with
a low pH organic salt capable of replacing
a wide range of traditional acids. Provides
top-tier performance for cleaning tubs, tile,
grout, walls, toilet bowls, urinals, shower
stalls and other bathroom surfaces.
P/N 74073 (1 gal. Container)
Eco-Friendly Peroxide Cleaner
A highly concentrated, multi-purpose
cleaner providing top-tier performance as
a Glass Cleaner, Multi-Purpose Cleaner
and a Restroom Cleaner depending upon
dilution. Eco-Friendly Peroxide Cleaner
meets the requirements of the GS-37
Green Seal™ Standard. It has a pleasant
orange scent.
P/N 74076 (1 gal. Container)
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.109
30
Dispensing Equipment
Dispenser for GreenWāv Commercial Gel
P/N 1820
GreenWāv Commercial Gel eliminates odor in the air. The continuous release formulation
works around the clock, providing 24/7 odor control. Especially effective for combating
persistent odor problems that may not be avoidable or correctable.
Features
• The dispennser holds one jar of 8 oz. gel.
• Can be easily mounted to most surfaces.
• Functional and subtle; hides the product out of sight allowing it to work discreetly.
• ADA Compliant.
Sure-Shot Sprayer
P/N 1700
Refillable, rechargeable and completely portable, the Sure Shot Sprayer features
metal construction, brass nozzles, and corrosion resistant internal working parts.
Features
•
•
•
•
•
32 oz. liquid capacity
Red epoxy powder coated finish
Can be used with oil and solvent based materials
Works great for cleaners, degreasers, penetrating oils, brake cleaners, and solvents
Just fill the sprayer two-thirds with product, pressurize to 80 - 150 psi and spray.
Accessory Kits
Nozzle Kit, P/N 50016
• Coarse Spray Nozzle
• Extra Fine Spray Nozzle
• Fine Spray Nozzle
• Flat Spray Nozzle
• Plastic Adjustable
Nozzle With Adapter
Nozzle Extension, P/N 50017
Use 12" Nozzle Extension With:
• Pin Stream Nozzle
• Regular Spray Nozzle
• Coarse Spray Nozzle
• Extra Fine Spray Nozzle
• Flat Spray Nozzle
Repair Kit, P/N 50018
• Inner Adapter Washer
• Valve and Valve Spring
• Valve Spring
• Stuffing Box Packing
• Stuffing Box Nut
• Cotter Pin
• Valve Trigger
• Filler Cap Assembly
• Regular Spray Nozzle
• Valve Seat Adapter (Male)
• Outer Adapter Washer
30
Plastic Tank Sprayer
Compressed Air Sprayer
P/N 1687
Pressurized plastic tank
sprayer with relief valve
and adjustable nozzle.
Shut-off valve in handle.
Capacity: 2 gallons.
Weight: 6 lbs.
P/N -1688
High pressure polyethylene
compressed air sprayer sprays
fine mist. Adjustable nozzle.
Hand held.
Capacity: 2 quarts.
Weight: 2 lbs.
30.110
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Dispensing Equipment
Spray Can Tool
Part #1818
FullGrip trigger with double leverage action provides effortless spray control.
FutureLock attachment ring makes attaching and removing cans easy.
Features
• Fits 100% of all standard spray cans.
• Optimized design uniquely positions the relationship between the handle, trigger and
spray can, providing greater balance while eliminating finger, wrist and forearm strain
• Patent pending design reduces SqueezeForce (the amount of pressure required to
actuate a spray can’s nozzle) by up to 80% compared to our competition
• ComfortTouch patent pending handle and trigger design
• Contoured, ergonomic gripping surfaces correspond to the natural angles and
positions of the fingers, hand, palm, wrist and forearm
• Arthritis-friendly design
• Made in the USA
Trigger Sprayer
Plastic Bottles
Part #1690
16 oz. plastic bottle with adjustable
nozzle to give a spray from mist to jet.
Part #1698
32 oz. plastic bottle with adjustable
nozzle to give a spray from mist to jet.
Trigger Sprayer
Part #1801
Heavy duty quality trigger sprayer
is engineered for a variety of liquids.
A comfortable trigger type operation
and large fine spray pattern makes
any job easier.
• Nozzle adjusts from fine
mist to a jet stream.
• Resists organic and acidic chemicals.
Part #1697
All-purpose trigger sprayer for 32 oz. plastic bottle.
Foamer Trigger Sprayer
Part #1699
Foamer trigger sprayer creates
a thick sudsy blanket for heavy
soil removal. Adapts to 16 oz.
and 32 oz. bottles.
36 oz.
Measurable
Bottle
30
Part #1800
36 oz. PVC clear bottle
multi-measured with printed
oz./ml. dilution scale.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.111
Dispensing Equipment
Plastic Drum Pump
Drum Dolly
Part #1692
Lift style 22 ounches per full stroke. Fits
any 15, 20, 30, 35 and 55 gallon drum.
Head threaded to fit 3/4" hose coupling.
Metal Drum Pump
Part #1694
Lift style 22 ounces per full stroke.
Unplated. Bung bushing will fit any 15, 20,
30, 35 and 55 gallon drum. Head threaded
to fit 3/4" hose coupling.
2" Drum
Faucet
Part #1803
HIGH FLOW – Durable
polyethylene drum faucet
in 2" diameter for general
purpose use.
Drum
Faucet
Part #1695
3/4" polyethylene drum
faucet for easy flow and
instant control.
30
Drum Wrench
Part #1804
• Welded steel
• Supports 400 lbs.
• For 55 gallon size drums
• 24"diameter
• Durable 3" steel swivel wheels
Rotary Barrel
Pump Part #1808
A precision built pump for
transferring non-corrosive
petroleum based fluids, of light
to medium viscosity, at a rate of
approximately one gallon per 18
revolutions with SAE 10 oil. For
industrial, commercial, automotive
and agricultural applications.
• Rugged cast iron pump housing
• Heavy duty vanes with steel
springs adjust automatically
• All steel discharge spout
• Steel suction pipe
Plastic
Syphon Pump
Part #1693
Plastic syphon pump with
universal adapter. Fits
openings 3/4" to 1-3/8" inside
diameter. Use with 5, 6 and
10 gallon pails.
Part #1802
12" aluminum / magnesium alloy for plastic or metal.
Opens all standard 3/4" and 2" bungs.
30.112
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Dispensing Equipment
Air Operated
Grease Gun Part #8200
Air Operated Grease
Gun Kit
Designed for the automotive, truck,
agricultural and industrial professional.
Three way loading feature uses standard
14.5 oz. grease cartridge, bulk grease and
grease filler pump. Easy to disassemble
and clean. Complete with flexible grease
hose and heavy-duty 4-claw coupler. Handy
storage locating ring. Pressure ratio –
50:1. Air pressure required – 30-120 psi.
Suggested working air pressure – 90 psi.
Part #38200
Professional
Grease Gun
Part #8218
All steel construction with heavy-duty
epoxy finish provides resistance to
rust, acids and salts. Easy threeway loading with 14.5 oz. cartridge,
suction filled up to 16 oz. and from
grease gun filler. Complete with bulk
loader fitting to quickly adapt to bulk
fillers, 6" angle pipe and heavy-duty
coupler, with a spring loaded ball
check valve. Weight: 4 lbs. 11 oz.
12-Volt Cordless
Grease Gun
Part #9571
Ideal maintenance tool for
farms, fleets, factories and
Part #9571B
Battery Only
shops. Includes two 12-volt
NiCad rechargeable batteries,
a 1-hour charger, 30 in. flexible
hose and a durable carrying case for
long-lasting protection and storage. Delivers up
to 7000 psi. Holds 14 oz. grease cartridge. No pumping
required. Cartridge and bulk loading. Planetary gear
drive. Machined and hardened piston. Plated steel barrel.
Flexi Grease
Gun Part #8217
Continuously pumps grease while trigger is depressed.
"Butterfly-Lock" screw enables grip handle to rotate 360o.
3-way loading – 14 oz. cartridge, bulk or suction. Delivers
up to 6,000 psi. 90 psi recommended inlet pressure.
Manual operated grease gun head cap converts gun to
standard manually operated lever gun.
CONTAINS 28 PIECES IN A HANDY CARRYING CASE!
• Air Operated Grease Gun
• 5-3/8" Extension Pipe
• 12" High Pressure Whip Hose
• Manual Operated Gun Head
• 1/4" Quick Release Coupler
• 1/4" Hose Fitting
• Grease Coupler
• Grease Fittings (10)
• Combination Wrenches (6)
• 6" Long Nose Plier
• 8" Slip Joint Plier
• 4" x 6mm Screwdriver
• 4" x 6mm Phillips Head Screwdriver
• 5mm Hex Key Wrench
Mini Lube Unit
Part #8216
Professional hand powered lubricator
for fast, clean greasing. Develops
pressure of up to 10,000 psi, while
providing 30 grease shots per pump.
This push button 2 speed lubricator
will fit all standard 7 lb. grease tins.
Hi-pressure, professional grease
gun produces up to 7,500 psi.
Easy grip handle allows for single
hand operation. Flexible extension
is also included.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.113
30
Dispensing Equipment
3M Fire Barrier Foam
FIP 1-Step, Guns
AutoDose™ Drain Manager
HandyMax® HMS-G4C2
Manual Gun
PowerMax® HPS-4C2
Battery-Powered Gun
P/N 9572
P/N 9573
Utilizing the flexible programming capabilities of the
AutoDose line of dispensers allows the user to dose
drains,cooling towers, boilers, pools, lubrication systems or
other areas at the appropriate times. An easily programmed
timer turns the pump on and off to ensure the regular dosing
of chemicals.
• Corrosion resistant cabinet fitted to pail or wall for
demanding environments
• Easy to program timer with pin lockout for security
• During normal operation, the timer runs on the same
power source as the pump, simplifying system
maintenance (only one set of batteries to replace)
• Internal backup battery in timer maintains program even
when main power source is disconnected or inoperative
• Automatic battery-life monitoring technology ensures
dosing accuracy throughout life of battery
• No tools required for maintenance of pump assembly
• Low battery indicator
• Maximum flexibility for customized dosing
• Choice of days, time (AM or PM) and dosings
(in one ounce or 30 ml increments)
• Up to 24 dosing periods per 24 hours
• Capability to dose every day, or just on specific days
Grease Oil Pump
P/N 16509
Dual cup Buna-N rubber plunger. All steel construction.
Needs no priming. Capacity over one pint.
Twelve inch vinyl hose. One piece handle.
Will handle all non-corrosive fluids.
Drop-Tite™ Epoxy System
Dual Cartridge Caulking Gun
P/N 8250
Designed with an in-line rod system and special friction plate
to provide exceptional force. Dispenses faster and reduces
worker exertion and fatigue.
30
Caulking Gun –
Smooth Rod
P/N 8253
Hex smooth-rod design with thumb
release and poker. Uses standard
10 oz. 8-1/2" drop-in cartridges. High
carbon, heat treated steel and riveted
construction. Easy to use with a solid
grip and trigger to reduce hand fatigue.
Zinc electro-plated working parts provide corrosion resistance
to the elements and a wide variety of caulking materials.
Heavy-duty (.060) steel for durability and long working life.
30.114
P/N 1816
Centerfeed Dispenser
P/N 1788
These dispensers simplify and
complement any environment, providing
a clean, hygienic appearance. The design
ensures easy and intuitive maintenance,
refilling and use. Ideal for high traffic
environments. No cross contamination
from levers or cranks.The portion control
feature dispenses one towel every time.
Simple and reliable.
• For Hand Towels, P/N 28237
Center-Pull Dispenser
P/N 1789
This dispenser offers single-sheet
release requiring only one hand to
tear off. Made of tough impact
resistant materials. One of the most
vandal-proof, break resistant, chemical
and flame resistant products for heavy
use applications.
• For Wipes, P/Ns 28235 & 28236
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
Dispensing Equipment
Sani-Smooth Dispenser
Traffic
Marking
Machine
P/N 1819
For hanging and dispensing Red Lion™
Sani-Smooth foaming aerosol hand sanitizer
(P/N 74486). Provides convenience and
portability. Mounting hardware included.
P/N 1810
Wall Mount Hand Cleaner
Pump Dispenser
Designed exclusively for Traffic Striping Marker Paints.
Applies clean, crisp even stripes or marks from 2” to 4”.
Use on porous surfaces ranging from asphalt to concrete.
Athletic
Marking
Machine
This universal dispenser allows metered
use of Red Lion H.D. Citrus Scrub
Hand Cleaner. Consistently controls
the amount of hand cleaner dispensed,
eliminating waste. Designed to offer
years of trouble-free service.
P/N 1811
P/N 1806
SOAP DISPENSER / 85 FL. OZ. BOTTLES
Black Dispenser, P/N 1832
For use with:
• P/N 74629 Antimicrobial Hand
Cleaner and Sanitizer
Designed with larger wheels and to be used exclusively with
Athletic Field Striping Paints only. Ready to use and requires
no accessories. Allows applications of lines up to 2'' to 4'' on
athletic fields or other turf surfaces.
Marking Wand
Part #1812
DESCRIPTION
PART
Soap Dispenser, for 85 fl. oz. Bottles
Easy loading. Machine is ready to
use and requires no accessories.
33” overall extension and light touch
makes marking simple and
accurate. Nickel zinc plating makes
it durable and corrosion resistant.
Great for golf courses, utilities,
surveyors, contractors and more.
1832
SOAP DISPENSER / 120 FL. OZ. BOTTLES
Traffic Marking
Applicator
Gray Dispenser, P/N 1830
For use with 120 fl. oz. Bottles
For use with:
• P/N 74630 Heavy Duty Scrub Hand Soap
• P/N 74631 H.D. Citrus Hand Soap
• P/N 74471 Cherry Impact Hand Soap
• P/N 74458 Magic Hand Soap
DESCRIPTION
Designed for heavy-duty paint
application where a wider stripe
is required. For use on concrete,
asphalt and athletic fields. Easy
loading, with light touch control that
makes marking simple and accurate.
PART
Soap Dispenser, for 120 fl. oz. Bottles
030115
040115
P/N 1809
Use with all 20 oz. Traffic or Athletic
Marker Paints only.
1830
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
30.115
30
Bulk Chemical Dilution Chart
30
PRICE PER GALLON AT STANDARD DILUTIONS
GAL.
COST
1:8
1:10
1:12
1:16
1:20
1:25
1:32
1:40
1:64
1:128
$5.00
6.00
7.00
8.00
9.00
10.00
11.00
12.00
13.00
14.00
15.00
16.00
17.00
18.00
19.00
20.00
21.00
22.00
23.00
24.00
25.00
26.00
27.00
28.00
29.00
30.00
31.00
32.00
33.00
34.00
35.00
36.00
37.00
38.00
39.00
40.00
45.00
50.00
55.00
60.00
65.00
0.56
0.67
0.78
0.89
1.00
1.11
1.22
1.33
1.44
1.56
1.67
1.78
1.89
2.00
2.11
2.22
2.33
2.44
2.56
2.67
2.78
2.89
3.00
3.11
3.22
3.33
3.44
3.56
3.67
3.78
3.89
4.00
4.11
4.22
4.33
4.44
5.00
5.56
6.11
6.67
7.22
0.45
0.55
0.64
0.73
0.82
0.91
1.00
1.09
1.18
1.27
1.36
1.45
1.55
1.64
1.73
1.82
1.91
2.00
2.09
2.18
2.27
2.36
2.45
2.55
2.64
2.73
2.82
2.91
3.00
3.09
3.18
3.27
3.36
3.45
3.55
3.64
4.09
4.55
5.00
5.45
5.91
0.38
0.46
0.54
0.62
0.69
0.77
0.85
0.92
1.00
1.08
1.15
1.23
1.31
1.38
1.46
1.54
1.62
1.69
1.77
1.85
1.92
2.00
2.08
2.15
2.23
2.31
2.38
2.46
2.54
2.62
2.69
2.77
2.85
2.92
3.00
3.08
3.46
3.85
4.23
4.62
5.00
0.29
0.35
0.41
0.47
0.53
0.59
0.65
0.71
0.76
0.82
0.88
0.94
1.00
1.06
1.12
1.18
1.24
1.29
1.35
1.41
1.47
1.53
1.59
1.65
1.71
1.76
1.82
1.88
1.94
2.00
2.06
2.12
2.18
2.24
2.29
2.35
2.65
2.94
3.24
3.53
3.82
0.24
0.29
0.33
0.38
0.43
0.48
0.52
0.57
0.62
0.67
0.71
0.76
0.81
0.86
0.90
0.95
1.00
1.05
1.10
1.14
1.19
1.24
1.29
1.33
1.38
1.43
1.48
1.52
1.57
1.62
1.67
1.71
1.76
1.81
1.86
1.90
2.14
2.38
2.62
2.86
3.10
0.19
0.23
0.27
0.31
0.35
0.38
0.42
0.46
0.50
0.54
0.58
0.62
0.65
0.69
0.73
0.77
0.81
0.85
0.88
0.92
0.96
1.00
1.04
1.08
1.12
1.15
1.19
1.23
1.27
1.31
1.35
1.38
1.42
1.46
1.50
1.54
1.73
1.92
2.12
2.31
2.50
0.15
0.18
0.21
0.24
0.27
0.30
0.33
0.36
0.39
0.42
0.45
0.48
0.52
0.55
0.58
0.61
0.64
0.67
0.70
0.73
0.76
0.79
0.82
0.85
0.88
0.91
0.94
0.97
1.00
1.03
1.06
1.09
1.12
1.15
1.18
1.21
1.36
1.52
1.67
1.82
1.97
0.12
0.15
0.17
0.20
0.22
0.24
0.27
0.29
0.32
0.34
0.37
0.39
0.41
0.44
0.46
0.49
0.51
0.54
0.56
0.59
0.61
0.63
0.66
0.68
0.71
0.73
0.76
0.78
0.80
0.83
0.85
0.88
0.90
0.93
0.95
0.98
1.10
1.22
1.34
1.46
1.59
0.08
0.09
0.11
0.12
0.14
0.15
0.17
0.18
0.20
0.22
0.23
0.25
0.26
0.28
0.29
0.31
0.32
0.34
0.35
0.37
0.38
0.40
0.42
0.43
0.45
0.46
0.48
0.49
0.51
0.52
0.54
0.55
0.57
0.58
0.60
0.62
0.69
0.77
0.85
0.92
1.00
0.04
0.05
0.05
0.06
0.07
0.08
0.09
0.09
0.10
0.11
0.12
0.12
0.13
0.14
0.15
0.16
0.16
0.17
0.18
0.19
0.19
0.20
0.21
0.22
0.22
0.23
0.24
0.25
0.26
0.26
0.27
0.28
0.29
0.29
0.30
0.31
0.35
0.39
0.43
0.47
0.50
30.116
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
030115
R-134a Lubricant Reference Chart
R-134a LUBRICANT REFERENCE CHART
The Following Compressors Utilize Factory Filled PAG Lubricants.
OEM LUBRICANT CoolPro LUBRICANT SYSTEM LUBRICANT CAPACITY
NUMBER
VISCOSITY
OUNCES
MILLILITERS
VEHICLE
MANUFACTURER
COMPRESSOR
MANUFACTURER
COMPRESSOR
MODEL
Acura
Nippondenso
10P
ND8
PAG 46
6-7
177-207
Alfa Romeo
Sanden
SDV
SP10
PAG 46
4
118
Audi
Audi
Diesel Kiki/Zexel
Nippondenso
DCW
10P
ZXL100
ND8
PAG 46
PAG 46
5-6
6-7
148-177
177-207
BMW
BMW
BMW
BMW
Seiko Seiki
Nippondenso
Bosch / Behr
Bosch / Behr
SS
10P
Wing
Axial
SX10
ND8
-
PAG 46
PAG 46
PAG 46
PAG 100
6
6-7
6-7
5-6
177
177-207
177-207
148-177
Chrysler
Chrysler
Chrysler
Chrysler
Chrysler
Nippondenso
Nippondenso
Sanden
Sanden
Mitsubishi
10PA
6C / 6CA
TR / TRS
SD
FX
ND8
ND8
SP10
SP20
P56
PAG 46
PAG 46
PAG 46
PAG 100
PAG 46
6-7
8-9
6
5
9-10
177-207
237-266
177
148
266-296
Jeep / Eagle
Jeep / Eagle
Jeep / Eagle
Sanden
Sanden
Nippondenso
SD
TR
10P / 10PA
SP20
SP10
ND8
PAG 100
PAG 46
PAG 46
5
4-5
6-7
148
118-148
177-207
Citroen
Sanden
SD7
SP20
PAG100
5
148
Ferrari
Sanden
SDV
SP10
PAG 46
4
118
Fiat
Sanden
SD7
SP20
PAG 100
5-6
148-177
Ford
Ford
Ford
Ford
Ford
Nippondenso
Sanden
Panasonic
FS10 / FX15
10P / 10PA
SD
Rotary
YN12 / 12A
ND8
SP20
YN12 / 12A
PAG46
PAG 46
PAG 100
PAG 46
7
6-7
5
4-5
207
177-207
148
118-148
G.M.
G.M.
G.M.
G.M.
G.M.
G.M.
G.M.
Delphi / Harrison
Delphi / Harrison
Delphi / Harrison
Delphi / Harrison
Nippondenso
Sanden
Sanden
V5 Retro
V5 R-134a
HR6 / HD6 / HT6
R4
10PA
SD7
SD5
12346305
12345923
12345923
12345923
ND8
SP20
SP20
PAG 150
PAG 150
PAG 150
PAG 150
PAG 46
PAG 100
PAG 100
8
8
8
4-5
6-7
5
6
237
237
237
118-148
177-207
148
177
Geo
Nippondenso
10PO
ND8
PAG 46
5-6
148-177
G.M. Saturn
Diesel Kiki/Zexel
DKV
ZXL200
PAG 150
6-7
177-207
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.117
30
R-134a Lubricant Reference Chart
R-134a LUBRICANT REFERENCE CHART
The Following Compressors Utilize Factory Filled PAG Lubricants.
OEM LUBRICANT CoolPro LUBRICANT SYSTEM LUBRICANT CAPACITY
NUMBER
VISCOSITY
OUNCES MILLILITERS
VEHICLE
MANUFACTURER
COMPRESSOR
MANUFACTURER
COMPRESSOR
MODEL
G.M. Saturn
Diesel Kiki/Zexel
DCV
ZXL200
PAG 150
5-6
148-177
Honda
Honda
Honda
Honda
Sanden
Sanden
Nippondenso
Nippondenso
TR
SD
10P
HADSYS. 7 Cyl.
SP10
SP20
ND8
SP10
PAG 46
PAG 100
PAG46
PAG 46
6
5-6
6-7
5-6
177
148-177
177-207
148-177
Hyundai
Hyundai
Ford
Halla
FS10
FX15 / HS10
YN12 / 12A
FD46X6
PAG 46
PAG 46
7
6-7
207
177-207
Infiniti
Infiniti
Infiniti
Zexel
Calsonic
Zexel
CVW
-
Type R
Type S
Type S
PAG 150
PAG 46
PAG 46
4-5
7-8
6-7
118-148
207-237
177-207
Isuzu
Isuzu
Isuzu
Isuzu
Zexel
G.M.
Diesel Kiki/Zexel
Diesel Kiki/Zexel
V5
KC50
Rotary
ZXL100
12345923
ZXL200
ZXL100
PAG 46
PAG 150
PAG 150
PAG 46
4-5
8
5-6
4-5
118-148
237
148-177
118-148
Jaguar
Jaguar
Sanden
Sanden
SD7H
SD
SP20
SP20
PAG 100
PAG 100
5
6
148
177
Lamborghini
Sanden
SD7
SP20
PAG 100
5
148
Lancia
Sanden
SD7
SP20
PAG 100
5
148
Land Rover
Land Rover
Sanden
Sanden
TRS
SD7
SP10
SP20
PAG 46
PAG 100
4
5
118
148
Lexus
Nippondenso
10PA
ND8
PAG 46
6-7
177-207
Lotus
Sanden
SD
SP20
PAG 46
6
177
Mazda
Mazda
Mazda
Mazda
Panasonic
Nippondenso
Ford
Sanden
Rotary
TV
FS10
SD
ATM0S10
ND9
YN12 / 12A
SP20
PAG 46
PAG 100
PAG 46
PAG 100
3-4
6
7
5
89-118
177
207
148
Mercedes
Mercedes
Nippondenso
Nippondenso
6CA
10P / 10PA
ND8
ND8
PAG 46
PAG 46
8-9
6-7
237-266
177-207
Mitsubishi
Mitsubishi
Mitsubishi
Nippondenso
FX / MSC
10P / 10PA
P56
P56
PAG 46
PAG 46
4-5
6-7
118-148
177-207
30
30.118
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
R-134a Lubricant Reference Chart
R-134a LUBRICANT REFERENCE CHART
The Following Compressors Utilize Factory Filled PAG Lubricants.
OEM LUBRICANT CoolPro LUBRICANT SYSTEM LUBRICANT CAPACITY
NUMBER
VISCOSITY
OUNCES MILLILITERS
VEHICLE
MANUFACTURER
COMPRESSOR
MANUFACTURER
COMPRESSOR
MODEL
Nissan
Nissan
Nissan
Nissan
Diesel Kiki/Zexel
Calsonic
Diesel Kiki/Nihon
Diesel Kiki/Zexel
DKV / DCV
Rotary
DKS / Rotary
DKV / Rotary
Type R
Type S
Type S
ZXL200
PAG 150
PAG 46
PAG 46
PAG 150
6-7
6-7
7-8
6-7
177-207
177-207
207-237
177-207
Opel
Delphi / Harrison
V5
12345923
PAG 150
8
237
Porsche
Nippondenso
10P
ND8
PAG 46
6-7
177-207
Peugeot
Sanden
SD7
SP20
PAG 100
5
148
Renault
Renault
Renault
Sanden
Sanden
Sanden
SDV
SD7
TRS
SP10
SP20
SP10
PAG 46
PAG 100
PAG 46
4
5
4
118
148
118
Rolls Royce
Sanden
SDV
SP10
PAG 46
4
118
Rover
Rover
Rover
Sanden
Sanden
Nippondenso
SD7
SDV
10P
SP20
SP10
ND8
PAG 100
PAG 46
PAG 46
5
4
6-7
148
118
177-207
Saab
Seiko Seiki
SS
S10X
PAG 46
5-6
148-177
Seat
Sanden
SDV
SP10
PAG 46
4
118
Skoda
Sanden
SD7
SP20
PAG 100
5
148
Subaru
Subaru
Zexel
Diesel Kiki
Rotary
15CH
Type R
ZXL100
PAG 150
PAG 46
6-7
6
177-207
177
Suzuki
Suzuki
Sanden
Nippondenso
SD
10P
SP20
ND8
PAG 100
PAG 46
6
6-7
177
177-207
Toyota
Toyota
Nippondenso
Nippondenso
10P / 10PA
TV
ND8
ND9
PAG 46
PAG 100
6-7
6
177-207
177
V5
12345923
PAG 150
8
237
Vauxhaul (GM) Delphi / Harrison
Volkswagen
Volkswagen
Sanden
Sanden
SD / SD7
SDV
SP20
SP10
PAG 100
PAG 46
5-6
4
148-177
118
Volvo
Volvo
Seiko Seiki
Sanden
SS
SD / SD7
S10X
SP20
PAG 46
PAG 100
5-6
5-6
148-177
148-177
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30
30.119
R-134a Lubricant Reference Chart
R-134a LUBRICANT REFERENCE CHART
The Following Compressors Utilize Factory Filled POE Lubricants.
POE 100 Lubricant Can Be Used For Retrofitting All R-12 Compressor Models.
VEHICLE
MANUFACTURER
Jaguar
Jaguar
Jaguar
Jaguar
COMPRESSOR
MANUFACTURER
Sanden
Sanden
Delphi / Harrison
Diesel Kiki
COMPRESSOR
MODEL
SD7H15
SD5H15
R4
DKS
OEM
LUBRICANT #
POE 100
POE 100
POE 100
POE 100
SYSTEM LUBRICANT
CAPACITY (OUNCES)
SAAB
SAAB
SAAB
Seiko Seiki
Seiko Seiki
Sanden
SS170PSS
SS808
SD5H15
POE 100
POE 100
POE 100
6-7
6
6
Volvo
Volvo
Diesel Kiki
Sanden
DKS
SD510
POE 100
POE 100
6-6.5
5
5
6
5.5-6.5
5-6
30
30.120
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
R-134a Lubricant Reference Chart
CAUTION:
While great care was taken to construct these charts with OEM information, it is always
best to consult with the compressor or vehicle manufacturer on the exact lubricant type
and capacity. This information can also be found on each compressor model tag.
COMPRESSOR OIL CHECK (ALL COMPRESSORS)
7HEN SERVICING REFRIGERANT OIL ENSURE CORRECT OIL IS USED #URRENT MINERAL OIL LUBRICANTS USED WITH 2 SYSTEMS DO NOT
PROVIDEADEQUATELUBRICATIONFOR2ASYSTEMS.EWSYNTHETICOILSMADEFROMPOLYALKYLENEGLYCOL0!'HAVEBEEN
DEVELOPEDTOUSEIN2ASYSTEMS
&OR 2A SYSTEMS IT IS VERY IMPORTANT THAT !# SYSTEM LABELS AND COMPRESSOR LABELS ARE REFERENCED WHEN ITgS
NECESSARYTOADDOILTOASYSTEM.OTALL0!'OILSARETHESAME6EHICLEANDCOMPRESSORMANUFACTURERSWILLSPECIFYTHEOIL
USED!SANEXAMPLE,EXUSVEHICLESWITHA00!SWASHPLATEPISTONCOMPRESSORUSE0!'.$/),ANDTHE
ROTARYVANECOMPRESSORUSES0!'.$/),
4HEOILLEVELONSOMECOMPRESSORSMAYBECHECKEDWITHTHECOMPRESSORMOUNTEDINTHEVEHICLE/THERCOMPRESSORSMAY
HAVETOBEREMOVEDFOROILMEASUREMENTANDADDING4HESYSTEMMUSTBEDISCHARGEDOFREFRIGERANTFIRSTORCOMPRESSOR
MAYBEISOLATEDASPREVIOUSLYDESCRIBEDIFEQUIPPEDWITHSTEMTYPESERVICEVALVES
/NLY NEW PURE MOISTURE FREE REFRIGERANT OIL SHOULD BE USED IN THE !# SYSTEM 2EFRIGERATION OIL IS HIGHLY REFINED AND
DEHYDRATED 4HEREFORE THE OIL CONTAINER MUST ALWAYS BE KEPT TIGHTLY CLOSED WHEN NOT IN USE )F THE CONTAINER IS LEFT
UNCAPPEDEVENFORASHORTTIMEMOISTUREWILLBEABSORBEDFROMTHEATMOSPHEREBYTHEOILANDBEINTRODUCEDINTOTHEAIR
CONDITIONINGSYSTEM
)FPOSSIBLERUNTHEENGINEANDSYSTEMFORABOUTMINUTESTOALLOWPROPEROILDISTRIBUTIONTHROUGHTHESYSTEM
)FTHECOMPRESSOROILLEVELISCHECKEDWITHADIPSTICKEACHOUNCEOFNEWREFRIGERANTOILADDEDTOTHECOMPRESSORWILLRAISE
THEDIPSTICKREADINGAPPROXIMATELY2EPLACETHEOILPLUGSEALINGGASKETOR/RING
/N2AND2ASYSTEMSREFRIGERANTOILISALSOAVAILABLEINCHARGINGCANSWHICHAREADDEDTOTHESYSTEMINTHE
SAME MANNER AS ADDING REFRIGERANT 4HESE CANS ALSO CONTAIN REFRIGERANT AND ARE ADDED TO THE SYSTEM DURING CHARGING
PROCEDURES4HECANSAREUSUALLYOZCANSTWOOUNCESOFOILANDTWOOUNCESOFREFRIGERANT
TYPICAL OIL REPLACEMENT FOR INDIVIDUAL COMPONENTS
NOTE: The following is a general rule of thumb. Refer to an appropriate service manual for oil capacities on a
specific vehicle.
)FNOMAJOROILLOSSHASOCCURREDINTHESYSTEMANDONLYASINGLECOMPONENTHASTOBEREPLACEDOILCANBEADDEDTOTHE
SPECIFICCOMPONENT5SEAMOUNTSSHOWNBELOW
s#ONDENSERONEOUNCE
s2ECEIVERDRIERONEOUNCE
s$ESICCANTBAGIN6)2ONEOUNCEPLUSAMOUNTDRAINEDFROMRECEIVERDRIER
s%VAPORATOROUNCES
s!CCUMULATOROUNCES
NOTE: Oil distributes itself through the system during operation. It is not always necessary to place the oil in the
component being replaced. It is however, important that the oil does get introduced in to the system. If the
compressor is being replaced, the oil should be put in it, instead of elsewhere.
30
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.121
RED LION™ CAN PUNCTURING SYSTEM
ORGANIZE YOUR WASTE HANDLING ... RECYCLE AEROSOL CANS
AVOID COSTLY DISPOSAL FEES AND HAZARDOUS WASTE FINES
RECYCLING AND RECLAMATION
• Once relieved of contents, punctured aerosol cans are not regulated and may be recycled as
scrap metal or disposed of as solid waste.
• Residual liquids, released by RED LION Can Puncturing System and collected in drum, may be
eligible for reclamation through a hazardous waste handler, resulting in "waste minimization"
credits.
30
SAFETY
• Allows puncturing of aerosol cans without worker contact. The can is secured in the puncturing
housing and with a press of the handle, the puncture pin moves through a fluid-tight chamber
and pierces the can.
• RED LION Can Puncturing System leaves no sharp edges or crushed metal, the only effect on
the can is a small, smooth-edged hole.
• Residual contents are safely collected in the drum.
• The Combination Carbon/Coalescing Filter collects V.O.C.'s in filter reservoir.
• An anti-static wire enhances operational safety, required under Federal and Local codes.
• RED LION Can Puncturing System will not allow unsafe usage. Propane bottles or aerosol cans
inserted improperly cannot be punctured.
30.122
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
RED LION™ CAN PUNCTURING SYSTEM
CONVENIENCE
•
•
•
•
The unit and filter thread directly into the bungs of any standard 55, 35 or 20 gallon drum.
It's portable, weighing only 5 pounds.
Does not require a power source and is easily operated by hand.
Collects residual contents directly into the drum. (Most industrial solvents, lubricants,
paints and cleaners can be collected in the same drum. Caustics and pesticides should
be collected in 2 separate drums).
• Increases opportunities for recycling and waste minimization.
• Accommodates most standard sizes of aerosol cans.
CONSTRUCTION
• Made of aircraft aluminum, requiring no maintenance.
• All moving parts are 308 stainless steel for durability.
• Puncturing pin is O-ring sealed to prevent leakage. Grease packing
lubricates puncturing pin chamber with each use.
• Carbide-tipped puncturing pin withstands repeated, long-term use, showing no visible
wear after puncturing over 10,000 cans.
COMBINATION FILTER
• Threads directly into the 3/4" bung of any standard drum, effectively filtering and
collecting V.O.C.'s.
• Comprises a coalescing lower portion, which removes airborne organic compounds, and
an activated carbon upper portion, which absorbs odor. The coalescing portion combines
submicrometer aerosol particulate into droplets which are gravitationally drained into the
filter reservoir.
• Rain Hood on filter provides protection from elements for outdoor use.
COST SAVINGS
• Approximate cost of disposal of a 55 gallon drum
of aerosol cans (approx. 96 cans) ......................................................... $450 or $4.690/can
• Approximate cost of disposal of liquid hazardous waste from
4,000 "essentially empty" aerosol cans (one 55 gallon drum) ................. $300 or $.075/can
Savings per can .................................................................................................. $4.615/can
The cost of the RED LION Can Puncturing System
can be recouped in the first 100 cans!
P/N
DESCRIPTION
SHIPPING WEIGHT
1701
RED LION Can Puncturing System
(1 Puncturing Unit, 1 Filter, 1 Anti-Static Wire, 1 Pair Safety Goggles)
8 lbs.
1702
Coalescing Carbon Filter for Puncturing Unit
Puncturing Unit
1 lb.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.123
30
RED LION™ CAN PUNCTURING SYSTEM
QUESTIONS AND ANSWERS
INTRODUCTION
RED LION Can Puncturing System is a solution to the expense of solid waste disposal of aerosol cans. RCRA
regulations require that, unless relieved of pressure, aerosol cans be packed in a drum and manifested for solid
hazardous waste disposal. A drum holds 96 cans and costs as much as $1,500 for proper transportation and
disposal. With RED LION Can Puncturing System, the cans are not solid hazardous waste, but are fully recyclable.
PUNCTURING UNIT
Q. How is it operated?
A. The RED LION Can Puncturing System threads directly to the 2" bung of a 55-gallon drum. The filter is installed
on the 3/4" bung. The aerosol can is inserted (inverted) into the housing. The sliding cap is lowered and locked
into place. The handle is pressed and immediately released. You will hear the contents being released into
the drum.
Q. Must RED LION Can Puncturing System be installed only on 55-gallon drums?
A. No, all industry standard drums have 2" and 3/4" bung openings. However, this system should not be installed
on drums smaller than 20-gallon capacity to allow proper displacement of compressed gas released during
puncturing.
Q. How long does it take to puncture cans with RED LION Can Puncturing System?
A. It only takes 15-20 seconds for the can to be depleted after puncturing. One customer has punctured as many
as 1,200 cans on a one-man seven-hour shift.
Q. Will the Puncturing Unit accept any size aerosol can?
A. The system is designed to puncture any industry standard aerosol can, regardless of the length. The standard
unit will not puncture "jumbo" aerosol cans or 1" mini-diameter cans. A special-order unit is available for that
purpose.
Q. How much can scrap steel recycling be increased with the Can Puncturing System?
A. Generally, four aerosol cans equal a pound of steel. American industry consumes 3-billion aerosol cans per
year, amounting to 375,000 tons of steel.
Q. How many spent aerosols can be punctured into a drum?
A. Approximately 4,200 cans can be punctured before the drum is at maximum recommended capacity.
The drum should not be filled more than 75% full, to provide proper displacement for the released contents.
Q. What do you do with the drum of liquids once it is at the recommended "full" capacity?
A. Simply call the waste handler who is handling your other hazardous waste.
30
Q. Can the liquids collected into the drums be reclaimed or recycled?
A. Yes, if chlorinated and non-chlorinated liquids are collected into separate drums. Chlorinated liquids
(primarily solvents) can be recycled in-house as "parts cleaning solvent"; non-chlorinated liquids
(primarily paints) can be reclaimed. Either method may qualify for "waste minimization credit".
Q. Are there any aerosols that should not be co-mingled when collected into the drum?
A. Yes, caustics (such as oven cleaners) and pesticides should not be collected into a drum with other liquid
residuals. They can, however, be collected into segregated single-content drums designed either "pesticides
only" or "caustics only".
Q. Are all aerosols considered hazardous waste?
A. Yes, but not because of the primary product they contained. Spent aerosol cans would be considered empty,
and exempt from regulation, were it not for the fact that the compressed gas propellant is reactive to
heat and is still present in an empty can (40 CFR 261.23 (a) (6)).
30.124
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
RED LION™ CAN PUNCTURING SYSTEM
QUESTIONS AND ANSWERS
Q. Is the puncturing of aerosol cans with RED LION Can Puncturing System considered treatment?
A. No, according to the Office of Solid Waste and Emergency Response (OSWER), which stated that "the
puncturing, crushing, or shredding of non-empty aerosol cans which contain hazardous waste does not
constitute treatment pursuant to 260.10, and a RCRA permit or compliance with other hazardous waste
management regulations is not required. (Source Document: OSWER Directive #9432.012 (80) ).
Q. What does it cost to dispose of the collected liquids into the drum?
A. A Hazardous Waste handler will charge from $275 to $350 per 55-gallon drum for proper transportation and
recycling, reclamation and/or disposal. This represents the total disposal cost for the residual liquids of 4,200
spent aerosol cans. This compares to solid waste disposal cost of unpunctured aerosol cans of $650 to $1,200
per 96 cans! On a direct comparison of 4,200 spent cans, the cost saving with RED LION Can Puncturing
System ranges from $28,000 to $52,000.
FILTER
Q. How does the filter work?
A. It is composed of two parts: a coalescing lower portion and an activated carbon upper portion. The coalescing
portion collects microscopic airborne liquids from the gas and combines them into droplets which collect within
the filter chamber. The activated carbon absorbs oxygen and odor from the "dry" gas which has passed through
the coalescing portion. It effectively reduces VOC's from the escaping gas.
Q. Does any compressed gas remain in the drum?
A. The compressed gas seeks escape through the point of least resistance, which is the filter. However, a minimal
amount of gas may remain in the drum. By leaving the "last" can punctured within the housing until puncturing
is resumed, an effective prolonged seal can be maintained.
Q. Can pressure build in the drum?
A. The filter relieves at 3 psi, eliminating the possibility of unsafe pressure within the drum. Additionally, the
activated carbon portion of the filter has been designed to serve as a highly efficient flame arrestor.
Q. When does the filter need to be changed?
A. After 45-60 days, or after puncturing 1,200 spent aerosols, whichever comes first, because the
activated-carbon will reach its maximum absorption level.
Q. Once used, is the filter considered hazardous waste?
A. The filter is designed to allow draining prior to disposal. If drained, the filter would stay below the 3% by weight
EPA allowance for non-regulated disposal. To drain filter, locate drain cock at bottom edge. Remove drain cock
cover while holding filter over RED LION Can Puncturing System housing. Drain filter through housing directly
into drum.
Q. Does the procedure require any permitting from the Air Quality Control Board?
A. No, permitting is only required when processing 50 pounds or more per hour, which is not the case
with aerosol cans. Permitting generally applies to gas-filling facilities: welding gases, large gas cylinders, etc.
ANTI-STATIC WIRE
Q. Why is the anti-static wire necessary?
A. In many cases, there is an OSHA requirement for grounding of "vessels" to prevent any build-up of static
electricity being transferred to a drum.The Anti-Static Wire grounds the drum and the RED LION Can Puncturing
System unit simultaneously. The RED LION Can Puncturing System itself is not capable of generating a static
charge. It is non-powered and utilizes a non-sparking carbide puncture pin.
050114
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.125
30
RED LION™ CHEMICALS – SELECTOR
APPLICATION:
AEROSOL & MISCELLANEOUS PROBLEM SOLVERS:
1. Adhesives
E-Z Poxy™:
200, Aluminum,
Aqua Repair, Concrete,
Copper, Cups,
Plastic and Wood
E-Z Poxy™ Fast Set
E-Z Poxy™ Metal and
Concrete
Drop-Tite™ Epoxy System
Fast-Fix™ Epoxy Patch Kit
Fast-Fix™ Pipe & Hose Repair Kit
Instant Adhesive
Instant Adhesive Gel
Liquid Electrical Tape
Loctite® Thread Treatment Sticks
RTV Black, Clear, Red and White
Spray Adhesive
PVC & CPVC Cements
Pow-R-Bond
Stud Lock and Bearing Mount
Super Adhesive Sealant
2. Automotive
Anti-Seize
Anti-Seize II
Battery Cleaner
Battery Protector
Belt Dressing
Brake Cleaner N.C.
Choke & Carb Cleaner
4-Way Plus
Fast-Fix™ Pipe &
Hose Repair Kit
Gasket & Paint Remover
Gear Oil
Gear Re-Nu™
Insta-Clean™
Insta-Clean Wipes
Insta-Shine™ Truck/Bus Protectant
Penetrating Oil
Prep-Solve
RTV Black Gasket Maker
RTV Red Hi-Temp Gasket Maker
Safe-T-Line™ Engine Cleaner
Super Impact Grease
White Grease
A&R Tabs
Citrus Grease Digester
Degreaser
Dis-N-Clean
Easy-Out™ Stain
Remover
Glass Cleaner
Glass Cleaner Wipes
Insta-Clean™
Insta-Clean Wipes
Prep-Solve
Quick Clean
Quick Shine™ Metal Polish
Quick-Solv
Quick-Zorb™
QX1 Bath & Tile Cleaner
QX1 Disinfectant Cleaner
QX1 Glass Cleaner w/Anti-Stat
QX1 Multi-Purpose Cleaner
Safe-T-Line™ Glass Cleaner
Safe-T-Line™ H.D. Citrus
Cleaner/Degreaser
Safe-T-Line™ Kleen & Shine™
Safe-T-Line™ No-Scrub™ Cleaner
3. Cleaning and
Degreasing
BULK PROBLEM SOLVERS:
Big Job™ Truck Wash
Diesel Fuel Additive
Super Gloss Wash-N-Wax™
Aluminum Brite™
Citrus Grease Digester
Clear View™
H.D. Citrus Cleaner/Digester
4. Drain & Sewer
Drain Opener
Citrus Grease Digester
Lift-Out™ Lift Station Degreaser
N-Zyme™ Drain Maintenance
5. Equipment
Coil and Filter Cleaner
Degreaser
Aluminum Brite
Coil and FIlter Cleaner
Equipment Clean
Stem Clean
Steam Clean HD
Super Clean
X-tra Clean™
6. Floor Care
Easy-Out™ Stain Remover
Floor Glo™ and Super Stripper™
7. Grounds Care
Concrete Crack Repair
Quick Clean
Safe-T-Line™ No-Scrub Cleaner
Vanish
8. Hand Cleaning
Hand Sanitizing Gel
H.D. Citrus Scrub
H.D. Citrus Wipes
PVA Hand Cleaner
Pow-R-Scrub Hand Cleaner
Pro-Clean Antibacterial Hand Soap
Pro-Clean Heavy Duty Hand Soap
Pro-Clean H.D. Citrus Scrub
Pro-Clean Pink Lotion Skin Cleaner
Pro-Clean Enriched Lotionized HS
30
30.126
Vanish
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
050114
RED LION™ CHEMICALS – SELECTOR
APPLICATION:
AEROSOL & MISCELLANEOUS PROBLEM SOLVERS:
BULK PROBLEM SOLVERS:
9. Maintenance
and Workbench
Air Tool Conditioner
Anti-Seize
Anti-Seize II
Contact Cleaner
Contact Cleaner P.S.
Cutting Fluid III
4-Way Plus
Penetrating Oil
4-Way Plus
Synthetic Cutting Fluid
10. Pests
Ant & Roach Spray
11. Odor Control
A&R Tabs
Baby Powder Odor Eliminator
Safe-T-Line™ Smoke &
Odor Eliminator
12. Paints and
Coatings
Ceiling Tile Spray White
Caterpillar – Old
Caterpillar – New
Clear Epoxy Grit
Cold Zinc Galvanizing
Gasket & Paint Remover
Pro-Coat™ Stainless Steel
Protective Coating
Red Insulating Varnish
Rust-Away™ Rust
Conversion Coating
Rust-Away II
Stor-Safe Rust Inhibitor
Striping & Marking Paints
Pro-Coat™ Paints:
Gloss Black
Gloss White
Gray Primer
Hi-Temp Flat Black
Industrial Gray
OSHA Blue
OSHA Green
OSHA Red
Phosphorescent
Red Oxide Primer
Undercoat
13. Sealers and
Protectors
Insta-Shine™ Truck/Bus
Protectant
Pro-Tex
RTV Black Gasket Maker
RTV Blue Gasket Maker
RTV Clear Gasket Maker
RTV Red Hi-Temp Gasket Maker
RTV White Gasket Maker
Stor-Safe™ Rust Inhibitor
Super Adhesive/Sealant
Teflon Pipe Sealant
Thread Sealant Hydraulic/
Pneumatic
14. Solvents and
Degreasers
Battery Cleaner
Battery Cleaner N.C.
Contact Cleaner E.S.
Degreaser
Safety Solvent E.S.
Safety Solvent III
15. Specialty
Lubricants
Anti-Seize
Anti-Seize II
Anti-Seize Aluminum
Anti-Seize Copper
Blue Grease
Cable & Chain Core Lube
Chain Lube and Clear Lube
Dielectric Grease
4-Way Plus
Hi-Temp Grease
Lithium Grease White
Low-Temp Grease
Moly Dry Lube
Penetrating Oil
Pro-Pull™ Wire Pulling Lube
Red Grease
Safe-T-Line™ Red Grease
Safe-T-Line™ Silicone
Silicone
Super Impact Grease
PTFE Dry Lube
TFG Grease
White Grease
16. Miscellenaous
Dust Blaster™, Dust Blaster II™, and Dust Blaster Max
No-Stick™ Welder's Anti-Spatter
050114
Safe-T-Line™ Hydro-Cool
Tool Coolant
Stor-Safe™ Rust Inhibitor
Stud Lock & Bearing Mount
Threadlocker
Tool Cool II
Toolube
Loctite® Thread Treatment Sticks
Insect Repellent
Wasp & Hornet Killer
Quick-Zorb
QX1 Odor Eliminator
Odor Eliminator
Odor Eliminator SC
Pleasant Scent
Pleasant Scent Green Apple
Equipment Clean
Safety Solv 2000™
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30
30.127
RED LION™ CHEMICALS – INDEX
30
ADHESIVES AND SEALANTS
248 MEDIUM BLUE THREADLOCKER
268 HI-STRENGTH RED THREADLOCKER
3/8 EPOXY MIXING TUBE
3M™ SPRAY ADHESIVE - MULTI-PURPOSE 27
3M™ SPRAY ADHESIVE - FOAM & FABRIC 24
3M™ SPRAY ADHESIVE - WOODWORKING 20
3M™ FIRE BARRIER SEALANT, CARTRIDGE, 10.1 FL OZ
3M™ FIRE BARRIER SEALANT, CARTRIDGE, 27 FL OZ
3M™ FIRE BARRIER SEALANT, SAUSAGE, 20 FL OZ
3M™ FIRE BARRIER SEALANT, 5 GALLON PAIL
3M™ FIRE BARRIER SEALANT, 2 GALLON PAIL
3M™ FIRE BARRIER MOLDABLE PUTTY, STICK
3M™ FIRE BARRIER MOLDABLE PUTTY, PAD
3M™ FIRE BARRIER FOAM FIP 1-STEP, 12.85 FL OZ
3M™ FIRE BARRIER FOAM FIP 1-STEP, NOZZLES
534 HI-TACK GASKET DRESSING
548 GASKET ELIMINATOR
668 RETAINING COMPOUND
COOLING SYSTEM SEALANT
CPVC ORANGE PLASTIC PIPE CEMENT
CRACK REPAIR KIT - 5 GALLON PAIL
DOUBLE BUBBLE EPOXY – EXTRA FAST
DOUBLE BUBBLE EPOXY – GENERAL PURPOSE
DOUBLE BUBBLE EPOXY– HI PEEL STRENGTH
DOUBLE BUBBLE EPOXY– MACHINABLE
DOUBLE BUBBLE EPOXY– REGULAR SETTING
DOUBLE BUBBLE EPOXY– WATER CLEAR
DOUBLE BUBBLE EPOXY– WET SURFACE PATCH
DOUBLE BUBBLE EPOXY– XTRA FAST NON-SAG
DOUBLE BUBBLE URETHANE – FLEXIBLE
DOUBLE BUBBLE URETHANE – SEMI-RIGID
DOUBLE BUBBLE URETHANE – VERY FLEXIBLE
DUAL EPOXY FOR CONCRETE ANCHOR
E-Z POXY™ CUPS
E-Z POXY™ 200
E-Z POXY™ ALUMINUM
E-Z POXY™ AQUA REPAIR
E-Z POXY™ CONCRETE
E-Z POXY™ FAST SET SYRINGE
E-Z POXY™ PLASTIC
E-Z POXY™ COPPER
E-Z POXY™ WOOD
FAST-FIX™ EPOXY PATCH KIT
FAST-FIX™ PIPE/HOSE REPAIR KIT
FAST WELD
HYDRAULIC/PNEUMATIC SEALANT
INSTANT ADHESIVE
INSTANT ADHESIVE GEL
INSULATING EXPANDABLE FOAM SEALANT
JUST FOR COPPER
LIQUID ELECTRICAL TAPE
LOCTITE STICK KIT
MULTI-PURPOSE PVC-ABS-CPVC CEMENT
MULTI-PURPOSE SEALANT BLACK
MULTI-PURPOSE SEALANT CLEAR
POW-R-BOND™ ADHESIVE
PST561 THREAD SEALANT
30.128
P/N
74561
74563
8251
74605
74606
74607
74580
74581
74582
74583
74584
74585
74586
74588
74588N
74570
74569
74571
74557
74552
74508
74499
74497
74496
74498
74493
74494
74495
74492
74417
74418
74419
74534
74514
74502
74505
74500
74526
74530
74527
74501
74503
74506
74507
74489
74524
74516
74525
74575
74553
74547
17931
74550
74573
74574
74187
74564
Page
30.19
30.19
30.1
30.11
30.11
30.11
30.22
30.22
30.22
30.22
30.22
30.22
30.22
30.23
30.23
30.20
30.20
30.20
30.17
30.12
30.1
30.2
30.2
30.2
30.2
30.3
30.3
30.3
30.3
30.4
30.4
30.4
30.1
30.6
30.5
30.5
30.5
30.6
30.7
30.7
30.6
30.7
30.8
30.8
30.9
30.18
30.10
30.10
30.16
30.10
30.11
30.19
30.12
30.16
30.16
30.11
30.19
ADHESIVES AND SEALANTS
PVC & CPVC PRIMER
PVC CLEAR PLASTIC PIPE CEMENT
RAPID SEAL
RTV - BLACK
RTV - BLUE
RTV (RED - HI TEMP)
RTV BLACK SILICONE
RTV BLUE SILICONE
RTV CLEAR SILICONE
RTV HI-TEMP RED SILICONE
RTV WHITE GASKET/SEALER
RTV WHITE SILICONE
RTV-CLEAR
SCREW GRAB
SEAL-IT, WHITE
SEAL-IT, SILVER
SEAL-IT, BLACK
SEAL-IT, CLEAR
SPRAY ADHESIVE
STUD LOCK/BEARING MOUNT - RED
STUD LOCK/BEARING MOUNT - RED
SUPER ADHESIVE SEALANT
TEFLON PIPE SEALANT
TEFLON PIPE THREAD SEALANT
TEFLON PIPE THREAD SEALANT
THREAD LOCKER HIGH STRENGTH - RED GEL
THREAD LOCKER MED STRENGTH - BLUE
THREAD LOCKER MED STRENGTH - BLUE
THREAD LOCKER MED STRENGTH - BLUE GEL
UV6800 SUPER ADHESIVE SEALANT
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
P/N
74549
74551
74572
74131
74132
74153
74548
74543
74541
74544
74128
74542
74133
74562
74578
74579
74573
74574
74130
74491
74515
74510
74511
74546
74545
74568
74513
74490
74567
74554
Page
30.12
30.12
30.16
30.14
30.14
30.14
30.15
30.15
30.15
30.15
30.14
30.15
30.14
30.21
30.16
30.16
30.16
30.16
30.11
30.18
30.18
30.13
30.21
30.21
30.21
30.17
30.17
30.17
30.17
30.13
050114
RED LION™ CHEMICALS – INDEX
BULK CHEMICALS
4 WAY PLUS - 1 GALLON
4 WAY PLUS - 30 GALLON
4 WAY PLUS - 55 GALLON
4 WAY PLUS - 5 GALLON
ALUMINUM BRITE - 1 GALLON
ALUMINUM BRITE - 30 GALLON
ALUMINUM BRITE - 55 GALLON
ALUMINUM BRITE - 5 GALLON
BIG JOB - 1 GALLON
BIG JOB - 30 GALLON
BIG JOB - 55 GALLON
BIG JOB - 5 GALLON
CLEAR VIEW - 55 GALLON
CLEAR VIEW - 5 GALLON
COIL & FILTER CLEANER - 1 GALLON
COIL & FILTER CLEANER - 30 GALLON
COIL & FILTER CLEANER - 55 GALLON
COIL & FILTER CLEANER - 5 GALLON
DIESEL FUEL ADDITIVE - 1 GALLON
DIESEL FUEL ADDITIVE - 30 GALLON
DIESEL FUEL ADDITIVE - 5 GALLON
DIESEL FUEL ADDITIVE - 55 GALLON
EQUIP CLEAN - 1 GALLON
EQUIP CLEAN - 30 GALLON
EQUIP CLEAN - 55 GALLON
EQUIP CLEAN - 5 GALLON
FLOOR GLO - 1 GALLON
FLOOR GLO - 30 GALLON
FLOOR GLO - 55 GALLON
FLOOR GLO - 5 GALLON
GREASE DIGESTER - 1 GALLON
GREASE DIGESTER - 30 GALLON
GREASE DIGESTER - 5 GALLON
GREASE DIGESTER - 55 GALLON
H.D. CITRUS CLEANER - 1 GALLON
H.D. CITRUS CLEANER - 30 GALLON
H.D. CITRUS CLEANER - 5 GALLON
H.D. CITRUS CLEANER - 55 GALLON
LIFT-OUT LIFT STATION DEGREASER - 1 GALLON
LIFT-OUT LIFT STATION DEGREASER - 5 GALLON
LIFT-OUT LIFT STATION DEGREASER - 55 GALLON
LIFT-OUT LIFT STATION DEGREASER - 30 GALLON
N-ZYME DRAIN MAINTENANCE - 1 GALLON
N-ZYME DRAIN MAINTENANCE - 30 GALLON
N-ZYME DRAIN MAINTENANCE - 5 GALLON
N-ZYME DRAIN MAINTENANCE - 55 GALLON
ODOR ELIMINATOR SC - 1 GALLON
ODOR ELIMINATOR SC - 30 GALLON
ODOR ELIMINATOR SC - 5 GALLON
ODOR ELIMINATOR SC - 55 GALLON
ODOR ELIMINATOR - 1 GALLON
ODOR ELIMINATOR - 30 GALLON
ODOR ELIMINATOR - 5 GALLON
ODOR ELIMINATOR - 55 GALLON
030115
P/N
74204
74201
74200
74203
74244
74241
74240
74243
74239
74236
74235
74238
74350
74353
74344
74341
74340
74343
74249
74246
74248
74245
74309
74306
74305
74308
74349
74346
74345
74348
74254
74251
74253
74250
74219
74216
74218
74215
74284
74283
74280
74281
74289
74286
74288
74285
74274
74271
74273
74270
74364
74361
74363
74360
Page
30.27
30.27
30.27
30.27
30.25
30.25
30.25
30.25
30.25
30.25
30.25
30.25
30.26
30.26
30.26
30.26
30.26
30.26
30.26
30.26
30.26
30.26
30.27
30.27
30.27
30.27
30.28
30.28
30.28
30.28
30.25
30.25
30.25
30.25
30.28
30.28
30.28
30.28
30.29
30.29
30.29
30.29
30.29
30.29
30.29
30.29
30.30
30.30
30.30
30.30
30.30
30.30
30.30
30.30
BULK CHEMICALS
PLEASANT SCENT - LEMON-LIME - 1 GALLON
PLEASANT SCENT - LEMON-LIME - 30 GALLON
PLEASANT SCENT - LEMON-LIME - 55 GALLON
PLEASANT SCENT - LEMON-LIME - 5 GALLON
PLEASANT SCENT GREEN APPLE - 1 GALLON
PLEASANT SCENT GREEN APPLE - 30 GALLON
PLEASANT SCENT GREEN APPLE - 5 GALLON
PLEASANT SCENT GREEN APPLE - 55 GALLON
QX1 DISINFECTANT
QX1 DISINFECTANT BOTTLE ONLY
QX1 GLASS/CRT CLEANER
QX1 GLASS/CRT CLEANER BOTTLE ONLY
QX1 MULTI-PURPOSE CLEANER
QX1 MULTI-PURPOSE CLEANER BOTTLE ONLY
QX1 ODOR ELIMINATOR
QX1 ODOR ELIMINATOR BOTTLE ONLY
QX1 SPRAYER ONLY
RED LION BRAKE CLEAN LOW VOC
RED LION BRAKE CLEAN LOW VOC
SAFETY SOLV 2000™ - 1 GALLON
SAFETY SOLV 2000™ - 30 GALLON
SAFETY SOLV 2000™ - 5 GALLON
SAFETY SOLV 2000™ - 55 GALLON
SOLUBLE CUTTING FLUID - 1 GALLON
SOLUBLE CUTTING FLUID - 30 GALLON
SOLUBLE CUTTING FLUID - 55 GALLON
SOLUBLE CUTTING FLUID - 5 GALLON
STEAM CLEAN - 1 GALLON
STEAM CLEAN - 30 GALLON
STEAM CLEAN - 55 GALLON
STEAM CLEAN - 5 GALLON
STEAM CLEAN HD - 30 GALLON
STEAM CLEAN HD - 55 GALLON
STEAM CLEAN HD - 5 GALLON
SUPER CLEAN - 1 GALLON
SUPER CLEAN - 30 GALLON
SUPER CLEAN - 55 GALLON
SUPER CLEAN - 5 GALLON
SUPER GLOSS - 1 GALLON
SUPER GLOSS - 30 GALLON
SUPER GLOSS - 5 GALLON
SUPER GLOSS - 55 GALLON
SUPER STRIPPER - 1 GALLON
SUPER STRIPPER - 30 GALLON
SUPER STRIPPER - 55 GALLON
SUPER STRIPPER - 5 GALLON
X-TRA CLEAN - 1 GALLON
X-TRA CLEAN - 30 GALLON
X-TRA CLEAN - 55 GALLON
X-TRA CLEAN - 5 GALLON
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
P/N
74234
74231
74230
74233
74229
74226
74228
74225
74712
74712B
74710
74710B
74711
74711B
74713
74713B
1815
74256
74257
74279
74276
74278
74275
74324
74321
74320
74323
74314
74311
74310
74313
74316
74315
74318
74304
74301
74300
74303
74224PF
74221PF
74223PF
74220PF
74359
74356
74355
74358
74339
74336
74335
74338
Page
30.31
30.31
30.31
30.31
30.31
30.31
30.31
30.31
30.38
30.38
30.36
30.36
30.37
30.37
30.38
30.38
30.36
30.31
30.31
30.31
30.31
30.31
30.31
30.34
30.34
30.34
30.34
30.32
30.32
30.32
30.32
30.32
30.32
30.32
30.33
30.33
30.33
30.33
30.33
30.33
30.33
30.33
30.33
30.33
30.33
30.33
30.34
30.34
30.34
30.34
30.129
30
RED LION™ CHEMICALS – INDEX
CLEANERS & DEGREASERS
A/C FLUSH - 1 GALLON
A/C FLUSH - 1 QUART
A/C FLUSH (NON-FLAMMABLE) - 1 GALLON
A/C FLUSH (NON-FLAMMABLE) - 1 QUART
AIR TOOL CONDITIONER
BASEBOARD STRIPPER/CLEANER
BATTERY ACID CLEANER/NEUTRALIZER WIPES
BATTERY PROTECTOR AND CLEANER
BRAKE CLEAN N.C.
CARPET SPOT DIRECT
CARPET/FABRIC SPOT REMOVER
CHOKE CARB CLEANER
CITRUS BLAST - H. D.
CITRUS GREASE DIGESTER - 1 QUART
CLEAN & FRESH BATHROOM WIPES
CLEANER / DEGREASER
CLUB CLEAN (GOLF EQUIPMENT CLEANER)
COIL/FILTER CLEANER
CONTACT CLEANER P.S.
DEGREASER
DIS-N-CLEAN™
DUST BLASTER (COMPLETE)
DUST BLASTER CARTRIDGE
DUST BLASTER MAX
DUST BLASTER VALVE
EASY OUT STAIN REMOVER
ELECTRONIC EQUIPMENT WIPES
FACILITY WIPES
FOAMING COIL CLEANER
GLASS AND SURFACE CLEANER
GLASS CLEANER
GLASS CLEANER WIPES
30
P/N
74383
74382
74385
74384
74136
74174
74098
74106
74147
74258
74262
74115
74142
974250
74457
74265
74199
74165
74704
74111
74188
8209
74182
74175
8214
74176
74456
28235
74268
74264
74120
74536
HIGH PERFORMANCE SAFE-ACID CLEANER - 1 QUART
74615
HIGH PERFORMANCE SAFE-ACID CLEANER - 1 GALLON 74616
HIGH PERFORMANCE SAFE-ACID CLEANER - 5 GALLON 74617
HIGH PERFORMANCE SAFE-ACID CLEANER - 55 GALLON 74618
INSTA-CLEAN
74121
INSTA-SHINE/TRUCK/BUS
74169
METAL CLEANER & TARNISH REMOVER
74537
PRO-TEX
74152
PVA WIPES
74528
QUICK CLEAN
74105
QUICK SOLV
74186
QUIK-SHINE METAL POLISH
74173
SHOP WIPES
28236
STAINLESS STEEL CLEANER WIPES
74610
SURFACE DISINFECTANT
74261
Page
30.41
30.41
30.41
30.41
30.44
30.46
30.40
30.40
30.39
30.49
30.49
30.39
30.50
30.47
30.43
30.43
30.41
30.39
30.46
30.46
30.42
30.48
30.48
30.48
30.48
30.49
30.48
30.51
30.39
30.43
30.44
30.44
30.47
30.47
30.47
30.47
30.45
30.40
30.45
30.47
30.44
30.50
30.50
30.45
30.51
30.45
30.42
SKIN CARE
ANTIMICROBIAL HAND CLEANER
AND SANITIZER - 85 fl. oz.
CHERRY IMPACT HAND CLEANER - 120 fl. oz.
CHERRY IMPACT HAND CLEANER - 18 fl. oz.
CITRUS CLEAN GF
HAND SANITIZING WIPES
HANDI-SANI INSTANT HAND SANITIZER - 4 OZ
H.D. CITRUS SCRUB HAND CLEANER - 1 GAL
H.D. CITRUS HAND SOAP - 120 fl. oz.
H.D. CITRUS HAND SOAP - 18 fl. oz.
H.D. MULTI-PURPOSE CITRUS TOWELS
HEAVY DUTY SCRUB HAND SOAP - 120 fl. oz.
HEAVY DUTY SCRUB HAND SOAP - 18 fl. oz.
P/N
74629
Page
30.54
74471
74472
74427
74539
74487
74521
74630
74633
74609
74630
74633
30.55
30.55
30.59
30.59
30.53
30.58
30.55
30.55
30.58
30.54
30.54
30.130
SKIN CARE
MAGIC HAND SOAP - 120 fl. oz.
MAGIC HAND SOAP - 18 fl. oz.
PAINT/VARNISH HAND CLEANER
POW-R-SCRUB HAND CLEANER
PROTECTIVE SKIN CREAM
PVA HAND CLEANER
SANI-SMOOTH HAND SANITIZING FOAM - 16 OZ
STOKO XTREME CARE CREAM - 100ML/3.38 OZ
STOKOLAN SKIN CARE CREAM - 100ML/3.38 OZ
P/N
74458
74459
74512
74416
74449
74512
74486
74454
74453
Page
30.56
30.56
30.58
30.57
30.59
30.58
30.53
30.52
30.52
INSECTICIDES
ANT AND ROACH SPRAY
BEDBUG KILLER
BUG BE GONE WIPES
FIRE ANT & INSECT DEHYDRATOR
INSECT REPELLENT
INSECT REPELLENT WRISTBANDS (GREEN)
INSECT REPELLENT WRISTBANDS (GLOW)
INSECT REPELLENT WRISTBANDS (PINK)
INSECT REPELLENT WRISTBANDS (RED)
INSECT REPELLENT WRISTBANDS (YELLOW)
INSECT REPELLENT WRISTBANDS (BLUE)
WASP AND HORNET KILLER SPRAY
P/N
74163
74485
74263
74269
74705
85085
85086
85087
85088
85089
85090
74161
Page
30.61
30.62
30.60
30.60
30.60
30.60
30.60
30.60
30.60
30.60
30.60
30.62
LUBRICANTS
4 WAY PLUS
ANTI-SEIZE
ANTI-SEIZE ALUMINUM - 8 OZ, BRUSH CAP
ANTI-SEIZE ALUMINUM - 16 OZ, EASY APPLICATOR
ANTI-SEIZE PRO-LUBE - ALUMINUM/COPPER
3.75 OZ, BRUSH CAP
ANTI-SEIZE II - COPPER - 8 OZ, BRUSH CAP
ANTI-SEIZE II - COPPER - 16 OZ, BRUSH CAP
BLUE GREASE - 35 LB / 5 GAL
BLUE GREASE - 120 LBS / 15 GAL
BLUE GREASE - 400 LBS / 50 GAL
C5-A COPPER ANTI-SEIZE STICK LUBRICANT
CABLE/CHAIN LUBE
CHAIN LUBE
CLEAR LUBE
CUTTING OIL III
CUTTING WAX - 16 OZ
CUTTING WAX - 2 OZ
DIELECTRIC GREASE
DRY LUBE PLUS
FREEZING ACTION PENETRANT
HI-TEMP GREASE
LITHIUM GREASE CARTRIDGE
LOW TEMP GREASE
MOLY DRY LUBE
PAG 100 VISCOSITY LUBRICANT - 8 OZ
PAG 150 VISCOSITY LUBRICANT - 8 OZ
PAG 46 VISCOSITY LUBRICANT - 8 OZ
PAG WITH/DYE 100 VISCOSITY LUBRICANT - 8 OZ
PAG WITH/DYE 150 VISCOSITY LUBRICANT - 8 OZ
PAG WITH/DYE 46 VISCOSITY LUBRICANT - 8 OZ
PENETRATING OIL
PNEUMATIC TOOL ANTI-SEIZE LUBRICANT
P/N
74107
74118
74423
74425
Page
30.63
30.75
30.75
30.75
74424
74426
74407
74436
74437
74438
74565
74151
74119
74137
74172
74560
74559
74439
74099
74556
74422
74428
74420
74123
74392
74393
74391
74387
74388
74386
74101
974375
30.76
30.76
30.76
30.63
30.63
30.63
30.77
30.64
30.64
30.65
30.73
30.74
30.74
30.65
30.67
30.77
30.66
30.66
30.67
30.68
30.78
30.78
30.78
30.79
30.79
30.79
30.68
30.68
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
030115
040115
RED LION™ CHEMICALS – INDEX
LUBRICANTS
POE 100 VISCOSITY LUBRICANT - 32 OZ
POE 100 VISCOSITY LUBRICANT - 8 OZ
POE WITH/DYE 100 VISCOSITY LUBRICANT - 8 OZ
POE WITH/DYE 100 VISCSTY LUBRICANT - 32 OZ
PTFE DRY LUBE
RED GREASE HI-TEMP
RED GREASE II-CARTRIDGE
RED GREASE III
RED GREASE III 120# - 20 GALLON
RED GREASE III 45# - 6 GALLON
SILICONE
SILVER GRADE ANTI-SEIZE STICK LUBRICANT
SUPER IMPACT MOLY G GREASE
TFG GREASE
TOOL COOL II
TOOLUBE
WHITE GREASE
WHITE GREASE (H1 CLASSIFIED)
WIRE PULLING LUBE
ZOOM SPOUT® OILER
P/N
74395
74394
74389
74390
74116
74415
74402
74404
74410
74408
74108
74566
74400
74406
74185
74523
74100
74104
74421
74255
Page
30.80
30.80
30.80
30.80
30.69
30.70
30.70
30.70
30.70
30.07
30.71
30.77
30.71
30.71
30.74
30.73
30.72
30.72
30.69
30.65
PAINTS & COATINGS
CATERPILLAR YELLOW PAINT - BEFORE '79
CATERPILLAR YELLOW PAINT - AFTER '79
COLD ZINC GALVANIZING
GLOSS BLACK ENAMEL
GLOSS WHITE ENAMEL
GRAY PRIMER
HI-TEMP BLACK ENAMEL
INDUSTRIAL GRAY ENAMEL
INSULATING VARNISH-RED
OSHA GREEN ENAMEL
OSHA RED ENAMEL
OSHA YELLOW ENAMEL
NON-CONDUCTIVE PAINT - GLOSSY WHITE
PRO-COAT CLEAR EPOXY GRIT COATING
“RED OXIDE PRIMER "IMPROVED"
RUST AWAY - 1 QUART
RUST AWAY - 1 GALLON
RUST AWAY II
SATIN BLACK TRIM PAINT
SCHOOL BUS YELLOW PAINT
SEYMOUR ATHLETIC FIELD STRIPING - ORANGE
SEYMOUR ATHLETIC FIELD STRIPING - WHITE
SEYMOUR GOLF COURSE STRIPING - RED
SEYMOUR GOLF COURSE STRIPING - WHITE
SEYMOUR STRIPING - ALERT ORANGE
SEYMOUR STRIPING - FLUORESCENT HOT PINK
SEYMOUR STRIPING - FLUORESCENT GREEN
SEYMOUR STRIPING - FLUORESCENT ORANGE
SEYMOUR STRIPING - FLUORESCENT RED
SEYMOUR STRIPING - PRECAUTION BLUE
SEYMOUR STRIPING - PURPLE
SEYMOUR STRIPING - SAFETY RED
SEYMOUR STRIPING - UTILITY YELLOW
SEYMOUR STRIPING - WHITE
P/N
500644
502311
74112
74014
74010
74003
74016
74012
74139
74196
74190
74194
74029
74024
74002
74157
74555
74701
74011
74146
74053
74052
74051
74050
74058
74061
74060
74056
74055
74057
74004
74059
74062
74054
Page
30.81
30.81
30.88
30.84
30.84
30.84
30.84
30.84
30.86
30.83
30.83
30.83
30.86
30.85
30.82
30.87
30.87
30.87
30.82
30.81
30.89
30.89
30.89
30.89
30.89
30.89
30.89
30.89
30.89
30.89
30.89
30.89
30.89
30.89
010115
PAINTS & COATINGS
SEYMOUR TRAFFIC STRIPING - RED
SEYMOUR TRAFFIC STRIPING - WHITE
SEYMOUR TRAFFIC STRIPING - YELLOW
SEYMOUR TRAFFIC STRIPING - HANDICAP BLUE
SNOW PLOW COATING - 1 GALLON
STAINLESS STEEL SPRAY COATING
UNDERCOAT (RUBBERIZED)
WELDING ANTI-SPATTER SPRAY
WHITE CEILING TILE PAINT
P/N
74065
74063
74064
74066
509280
74040
74129
74018
74134
Page
30.89
30.89
30.89
30.89
30.88
30.85
30.88
30.82
30.86
PAINT REMOVERS
GRAFFITI WIPES
GRAFFITI BARRIER - 1 QUART
GRAFFITI BARRIER - 1 GALLON
GRAFFITI BARRIER - 5 GALLON
GRAFFITI BARRIER - 55 GALLON
GASKET AND PAINT REMOVER
PREP SOLVE
P/N
74611
74625
74626
74627
74628
74113
74700
Page
30.91
30.92
30.92
30.92
30.92
30.90
30.90
SPECIALTY PRODUCTS
A&R TABS - UP TO 15 TONS PER TABLET
A&R TABS - UP TO 5 TONS PER TABLET
A/C LEAK STOP WITH UV DYE
BELT DRESSING
CHROMAGIC SPILL ABSORBENT
GUM OFF
ICE & FROST REMOVER
PRO DRAIN OPENER
SNOW & ICE MELTER - 50 LB. BOX
SNOW & ICE MELTER (PALLET / 48 BOXES)
QUICK-ZORB SPILL ABSORBENT
P/N
74721
74720
74381
74117
28234
74110
74488
74380
74608
74608P
74189
Page
30.93
30.93
30.96
30.93
30.94
30.95
30.95
30.93
30.95
30.95
30.94
ECO-FRIENDLY “GREEN” CHEMICALS
P/N
BIO-LUBE - 2 OZ
74266
BIO-LUBE - 8 OZ
74267
ECO-FRIENDLY CUTTING OIL
74084
ECO-FRIENDLY FLOOR STRIPPER - 1 GAL
74080
ECO-FRIENDLY FLOOR STRIPPER - 55 GAL
74082
ECO-FRIENDLY FLOOR STRIPPER - 5 GAL
74081
ECO-FRIENDLY GLASS CLEANER - 1 GAL
74070
ECO-FRIENDLY GLASS CLEANER - 55 GAL
74072
ECO-FRIENDLY GLASS CLEANER - 5 GAL
74071
ECO-FRIENDLY MULTI-PURPOSE CLEANER - 1 GAL 74067
ECO-FRIENDLY MULTI-PURPOSE CLEANER - 55 GAL74069
ECO-FRIENDLY MULTI-PURPOSE CLEANER - 5 GAL 74068
ECO-FRIENDLY PENETRATING OIL
74083
ECO-FRIENDLY PEROXIDE CLEANER - 1 GAL
74076
ECO-FRIENDLY TUB & TILE CLEANER - 1 GAL
74073
ECO-FRIENDLY TUB & TILE CLEANER - 55 GAL
74075
ECO-FRIENDLY TUB & TILE CLEANER - 5 GAL
74074
ECO-FRIENDLY ZINC-FREE SEAL & FINISH - 1 GAL 74077
ECO-FRIENDLY ZINC-FREE SEAL & FINISH - 55 GAL 74079
ECO-FRIENDLY ZINC-FREE SEAL & FINISH - 5 GAL 74078
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
Page
30.97
30.97
30.100
30.99
30.99
30.99
30.98
30.98
30.98
30.98
30.98
30.98
30.100
30.99
30.99
30.99
30.99
30.99
30.99
30.99
30.131
30
RED LION™ CHEMICALS – INDEX
SAFE-T-LINE PRODUCTS
ENGINE DEGREASER
H.D. CITRUS CLEANER
KLEEN & SHINE
SMOKE/ODOR ELIMINATOR
30
P/N
74183
74145
74127
74158
Page
30.102
30.102
30.101
30.102
ODOR ELIMINATORS
P/N
BABY POWDER ODOR ELIMINATOR
74166
CITRUS CREME METERED MIST
74460
CUCUMBER MELON METERED MIST
74434
FRESH LINEN AIR DEODORIZER
74469
FRESH LINEN METERED MIST
74465
FRUIT BASKET METERED MIST
74461
GREEWAV - AIR & SURFACE SPRAY - 32 OZ
74576
GREEWAV - COMMERCIAL GEL - 8 OZ
74577
LEMON ITALIAN ICE AIR DEODORIZER
74470
METERED AIR SANITIZER
74467
METERED MIST VARIETY PACK
200145
METERED MIST VARIETY PACK II
200177
ODOR NEUTRALIZING FOGGER
74468
PLEASANT SCENT - LEMON-LIME - 1 GAL
74234
PLEASANT SCENT - LEMON-LIME - 5 GAL
74233
PLEASANT SCENT - LEMON-LIME - 30 GAL
74231
PLEASANT SCENT - LEMON-LIME - 55 GAL
74230
PLEASANT SCENT - GREEN APPLE - 1 GAL
74229
PLEASANT SCENT - GREEN APPLE - 5 GAL
74228
PLEASANT SCENT - GREEN APPLE - 30 GAL
74226
PLEASANT SCENT - GREEN APPLE - 55 GAL
74225
PINA COLADA METERED MIST
74466
PINE FOREST METERED MIST
74464
POWDER FRESH METERED MIST
74462
RED CLOVER TEA METERED MIST
74433
URINAL DEODORANT SCREENS
74442, 74473-74483
VANILLA DELIGHT METERED MIST
74463
Page
30.103
30.106
30.106
30.104
30.106
30.106
30.105
30.105
30.103
30.103
30.106
30.106
30.104
30.106
30.106
30.106
30.106
30.106
30.106
30.106
30.106
30.106
30.106
30.106
30.106
30.105
30.106
DISPENSING EQUIPMENT
2'' DRUM FAUCET
32 OZ, SURE SHOT SPRAYER
36 OZ, MEASURABLE BOTTLE
3M™ HANDYMAX® MANUAL GUN
3M™ HANDYMAX® BATTERY-POWERED GUN
AIR OPERATED GREASE GUN
AIR OPERATED GREASE GUN KIT
ATHLETIC MARKING MACHINE
AUTODOSE™ DRAIN MANAGER
BOTTLE - ECO-FRIENDLY GLASS
BOTTLE - ECO-FRIENDLY MULTI-PURPOSE
BOTTLE - ECO-FRIENDLY PEROXIDE
BOTTLE - ECO-FRIENDLY TUB & TILE
CAULKING GUN-SMOOTH - 10 OZ
CENTERFEED DISPENSER (FOR 28237)
CENTER-PULL DISPENSER (FOR 28235 & 28236)
CHERRY IMPACT HAND CLEANER DISPENSER
COMPRESSION AIR SPRAYER - 2 QT
CORDLESS GREASE GUN
- GREASE GUN "REPLACEMENT BATTERY"
CURB MARKING WAND
DRUM DOLLY 400 LB
DRUM FAUCETS - 3/4''
DRUM WRENCH 12''
DUAL CAULKING GUN FOR P/N 74534
Page
30.112
30.110
30.111
30.114
30.114
30.113
30.113
30.115
30.114
30.107
30.107
30.107
30.107
30.114
30.114
30.114
30.115
30.110
30.113
30.113
30.115
30.112
30.112
30.112
30.114
30.132
P/N
1803
1700
1800
9572
9573
8200
38200
1811
1816
74070B
74067B
74076B
74073B
8253
1788
1789
1830
1688
9571
9571B
1809
1804
1695
1802
8250
DISPENSING EQUIPMENT
ECO-FRIENDLY GLASS CLEANER WALL DISPENSER
ECO-FRIENDLY MLTI-PURPOSE CLEANER WALL DISPENSER
ECO-FRIENDLY PEROXIDE CLEANER WALL DISPENSER
ECO-FRIENDLY TUB & TILE CLEANER WALL DISPENSER
FLEXI GREASE GUN
FOAMER TRIGGER SPRAYER ONLY
GEAR OIL PUMP
GREENWAV 8 OZ COMMERCIAL GEL DISPENSER
H.D. TRIGGER SPRAYER
MAGIC HAND SOAP DISPENSER
MARKING WAND
METAL DRUM PUMP
METERED MIST DISPENSER
NOZZLE KIT, FOR SURE-SHOT SPRAYER P/N 1700
NOZZLE EXTENSION - 12'' FOR SPRAYER P/N 1700
PLASTIC DRUM PUMP
PLASTIC SYPHON PUMP
POWER LUBE GREASE GUN
PRO CLEAN HAND SOAP DISPENSER
PROF GREASE GUN
REPAIR KIT FOR SPRAYER P/N 1700
ROTARY BARREL PUMP
SANI-SMOOTH DISPENSER
SPRAY CAN TOOL
SPRAY TRIGGER BOTTLE - 32 OZ
TANK SPRAYER - PLASTIC - 2 GAL
TRAFFIC MARKING MACHINE
TRIGGER SPRAYER, FOR 32 OZ BOTTLE
SPRAY TRIGGER BOTTLE - 16 OZ.
WALL MOUNT HAND CLEANER PUMP DISPENSER
P/N
1826
1824
1822
1828
8217
1699
16509
1820
1801
1830
1812
1694
1817
50016
50017
1692
1693
8216
1814
8218
50018
1808
1819
1818
1698
1687
1810
1697
1690
1806
Page
30.108
30.108
30.108
30.108
30.113
30.111
30.114
30.110
30.111
30.115
30.115
30.112
30.107
30.110
30.110
30.112
30.112
30.113
30.115
30.113
30.110
30.112
30.115
30.111
30.111
30.110
30.115
30.111
30.111
30.115
BULK CHEMICAL DILUTION CHART
30.116
R-134A LUBRICANT REFERENCE CHART
30.117
CAN PUNCTURING SYSTEM
CAN PUNCTURING SYSTEM
COALESCING CARBON FILTER
Q&A
CHEMICAL SELECTOR
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-888-567-2200
1701
1702
30.122
30.123
30.124
30.126
010115
TEST REPORT NO: 20520.01
REPRINT OF
TEST RESULTS OF
RED LION CAN
PUNCTURING SYSTEM.
MANUFACTURED BY
KATEC, INC.
TM
StarScan Test Services
prepared for
Katec, Incorporated
May 21, 1992
STAR Laboratories
St. Paul, MN
ABSTRACT
Capsule exhaust filters for use with Katec's pressurized paint can disposal system were tested for VOC removal and
total hydrocarbon emissions during the puncturing process. The results were compared with STEL values for each
of the VOC's tested and the desired 300 ppm hydrocarbon emission concentration. In addition, calculations were
performed to determine the maximum number of cans which could be processed per drum per day given a maximum
discharge of 15 pounds per drum per day limitation.
DAILY PROCESSING LIMITATION
Given the limitation of 15 pounds of propellent per day per drum, we have quantified the number of cans which may
be processed per day based upon the information supplied:
1. 97% of all cans are basically empty.
2. 3% of the cans range from nearly empty to full.
3. The propellent accounts for 1/3 of the amount of fluid in a full can.
By weighing cans before and after puncturing, it was determined that full cans had 15 oz. of fluid and empty cans
contained 1% of the original fluid weight. For purposes of calculation, we have assumed the 3% fraction of cans which
range from empty to full to be half full.
Consequently, the number of cans, X, which may be punctured per day per drum given the above conditions is:
[(97% of cans) x (1% full) x (15 oz./full can) x (33% propellent)] x (X)
+ [(3% of cans) x (50% full) x (15 oz./full can) x (33% propellent)] x (X)
= (15 pounds propellent/day/drum) x (16 oz./pound)
or,
(0.97)(0.01)(15)(0.333)X + (0.03)(0.50)(15)(0.33)X = (15)(16)
0.124X = 240
X = 1,935 cans/day/drum
Therefore, 1,935 cans per day per drum may be punctured given the limitation of 15 pounds of propellent per day
per drum.
VOC REMOVAL TESTING
METHOD
The test filter was tested by puncturing a paint can into a full drum (a 55 gallon drum filled approximately 10" from
top). For each paint can tested, all of the effluent from the filter was collected in Kevlar bags and a known volume
sample was drawn through one or two carbon media tubes. The tubes were then analyzed using a gas chromatagraph to determine the concentration of Acetone, Methyl Ethyl Ketone (MEK), Toluene and Xylene in the effluent.
RESULTS — RUSTOLEUM PAINT, GLOSS WHITE, 15 oz. CAN
CONCENTRATION (ppm)
ACETONE
MEK
OHSA LIMITS (STEL1)
1,000
300
NO FILTER
39
1
2
W/FILTER, full can (15 oz.)
>542
W/FILTER3, full can (15 oz.)
55
2
W/FILTER, empty can (<1 oz.)
<9
<7
1
STEL = Short Term Exposure Limit, — Exposure allowed in 15 minute period.
2
Slightly greater than 54 ppm limit of single tube sampling tube.
3
Sampled with two sampling tubes for Acetone determination
031693
CHROMATE - Quality...Service...Performance
TOLUENE
150
3,870
48
48
<5
XYLENE
150
3,131
4
8
<4
continued ➤
30A.3
TOTAL HYDROCARBON EMISSIONS
METHOD
A Flame Ionizing Detector (FID), calibrated to Methane, was used to measure the amount of hydrocarbon emissions
at two points six inches away from the filter. The first point was directly above the center of the filter, and the second
was to the side, toward the operator at a height even with the top of the filter. At each point, two cans of nearly empty
Rustoleum dark gray auto primer (12 oz. cans) were punctured and the maximum readings were recorded on the
FID.
CONDITIONS
1. 55 gallon drum: filled to approximately 10 inches from the top with water and paint.
2. Test filter through which one empty 15 oz. can (fumes only) had been discharged through filter prior to
these tests.
3. Outlet concentration readings with FID with no filter exceeded FID limitation of 1,000 ppm.
RESULTS
CAN
% FULL
11
1
1
1
TOP OF FILTER
(ppm)
100
80
—
—
SIDE OF FILTER
(ppm)
—
—
100
80
SUMMARY
It was calculated that 1,935 used paint cans/day/drum may be punctured for disposal and discharge less than the
15 pounds/drum/day limitation given a standard mix of 97% nearly empty cans (1% full) and 3% empty to full cans
(averaging 50% full).
With the use of the filter, the effluent concentration of VOC's was significantly less than the STEL for each of the
hydrocarbons tested (Acetone, MEK, Toluene and Xylene).
With the use of the filter, the total hydrocarbon concentration measured at points 6" from the filter during the
puncturing process was 80-100 ppm, significantly less than the 300 ppm desired limitation.
May 21, 1993
Date: _______________________________
Name: ______________________________
Mechanical Engineer, R&D Dept.
Title: _______________________________
30A.4
CHROMATE - Quality...Service...Performance
031603
TM
BULK CHEMICALS
The Finest Quality Chemicals Available
Red Lion™ Bulk Chemicals are superior products
resulting from extensive research and development.
They provide unmatched performance without compromising safety.
Available in 1, 5, 30 & 55 gallon bulk containers.
RED LION™ BULK CHEMICAL SIZES
DESCRIPTION
55 GAL.
30 GAL.
5 GAL.
1 GAL.*
QUART
ALUMINUM BRITETM
74240
74241
74243
—
974240
BIG JOB TRUCK WASH
74235
74236
74238
74239
974235
CITRUS GREASE DIGESTER
74250
74251
74253
74254
974250
CLEAR VIEWTM
74350
—
74353
—
974350
COIL & FILTER CLEANER
74340
74341
74343
74344
974340
DIESEL FUEL ADDITIVE
74245
74246
74248
74249
—
EQUIPMENT CLEAN
74305
74306
74308
74309
974305
FLOOR GLO
74345
74346
74348
74349
974345
H.D. CITRUS (CLEANER/DEGREASER)
74215
74216
74218
74219
974215
LIFT-OUTTM LIFT STATION DEGREASER
74280
74281
74283
74284
974280
N-ZYMETM DRAIN MAINTENANCE
74285
74286
74288
74289
974285
ODOR ELIMINATOR
74360
74361
74363
74364
974360
ODOR ELIMINATOR SC
74270
74271
74273
74274
—
PLEASANT SCENT
74230
74231
74233
74234
974230
PLEASANT SCENT GREEN APPLE
74225
74226
74228
74229
974225
SAFETY-SOLV 2000TM
74275
74276
74278
74279
974275
STEAM CLEAN
74310
74311
74313
74314
974310
STEAM CLEAN HD
74315
74316
74318
—
974315
SUPER CLEANTM
74300
74301
74303
74304
974300
74220PF
74221PF
74223PF
74224PF
974220PF
SUPER STRIPPER
74355
74356
74358
74359
974355
X-TRA CLEAN N.B.
74335
74336
74338
74339
974335
SUPER GLOSS WASH-N-WAX "PF"
*ONE (1) GALLON CONTAINERS PACKAGED FOUR (4) GALLONS PER CASE. FULL CASE SHIPMENTS ONLY (NO SPLITS). CAN BE SHIPPED VIA U.P.S.
110112
FOR MORE INFORMATION ON OUR PRODUCTS OR SYSTEMS, CALL 1-800-BUY-BOLT
30.BULK
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement