Baby Jogger city turn Quick Start Manual

The Baby Jogger City Turn car seat offers a secure and convenient ride for your growing child. It features rear-facing and forward-facing installation options, allowing you to adjust it as your child progresses. It also includes a tether for added safety and a cup holder for convenience. Check the level indicator to ensure proper installation. Choose the right recline position based on your child's weight. Read the manual for detailed instructions and discover the City Turn's full capabilities.

PDF

Document

LET’S GET
STARTED
Please review this guide carefully prior
to installation for tips, tricks and a
map to your new City Turn™ car seat.
For further information, reference the
instruction manual.
PKG0001381133A
GETTING TO KNOW
1
YOUR SEAT
4
6
5
2
3
7
8
9
11
12
10
13
11
1
HEADREST/HARNESS ADJUSTMENT LEVER
9
2
ROTATION LEVER
10
CUPHOLDER
3
LOWER ANCHOR STORAGE
11
REAR-FACING LEVEL INDICATOR
4
FORWARD-FACING BELT PATH
12
REAR-FACING RAPIDLOCK
5
TETHER
13
REAR-FACING BELT PATH
6
INSTRUCTION MANUAL STORAGE
7
RECLINE FOOT
8
RECLINE LEVER
FORWARD-FACING RAPIDLOCK
REAR-FACING INSTALLATION
FORWARD-FACING INSTALLATION
For children 4-50 lb (1.8-22 kg)
Instructions for installing using your vehicle’s seat belt.
1. Confirm your recline foot is
in the rear-facing position by
checking the label on the side
of the foot. If it is not, rotate
the recline foot located at the
base of the seat to the rearfacing position. The recline
foot is secure when it ‘CLICKS’
into place.
For children 22-65 lb (10-30 kg), 49” or less
Instructions for installing using your vehicle’s seat belt and tether.
5. Route both vehicle lap
and shoulder belt under the
rear-facing belt guides and
RAPIDLOCK arm.
2. Adjust recline foot between
positions 1-3 by squeezing the
recline lever and lifting the
base to extend/retract the
foot. Check that the recline
foot touches vehicle seat and
level indicator is in the correct
blue zone.
For children over 40 lb (18 kg),
MUST use recline position 1.
6. Buckle, then pull up on the
shoulder belt to tighten and
then buckle. Close the rearfacing RAPIDLOCK arm until
you hear ‘CLICK’. Note: Do not
pull on the belt with excessive
force. If the belt is too tight,
you will not be able to close
the RAPIDLOCK. Do not lock the
seat belt.
3. Squeeze rotation lever at
the front of the car seat and
rotate the seat to expose the
rear-facing belt path.
7. Rotate the seat back into
place until you hear ‘CLICK’
and confirm it is locked by
pushing the seat side-to-side
at belt path.
4. Open the
RAPIDLOCK arm.
rear-facing
1. Confirm your recline foot is
in the forward-facing position
by checking the label on the
side of the foot. If it is not,
rotate the recline foot located
at the base of the seat to the
forward-facing position. The
recline foot is secure when it
‘CLICKS’ into place.
6. Route seat belt through the
forward-facing belt path.
2. Adjust the recline foot
between positions 1-3 by
squeezing the recline lever
and lifting the base to extend/
retract the foot. For children
40-65 lb (18-30 kg), MUST use
recline position 1. For children
less than 40 lb (18 kg), MUST
use recline position 3.
7. Route seat belt behind
RAPIDLOCK arm.
3. Raise headrest to the highest
position to clear the forwardfacing belt path.
8. Buckle, then remove vehicle
belt slack by pressing down
firmly in the center of the car
seat and Note: Do not pull on
the belt with excessive force.
If the belt is too tight, you
will not be able to close the
RAPIDLOCK. Do not lock the
seat belt.
4. Remove tether from back of
seat and lay it over the front of
the seat.
9. Close the forward-facing
RAPIDLOCK arm until you hear
‘CLICK’.
5. Lift seat pad up and open
the forward-facing RAPIDLOCK
arm.
10. Locate your vehicle’s tether
anchor per your vehicle’s
instruction manual. Attach and
tighten the tether.
8. Verify the level indicator has
not changed.
TIP: The American Academy of Pediatrics recommends your child ride rear-facing
as long as possible, to the upper weight or height limit allowed by your car seat.
See page 21 in the Installation Manual for additional Rear-Facing installation instructions.
See page 28-33 in the Installation Manual for Rear-Facing with LOWER ANCHOR ATTACHMENT instructions.
See page 34 in the Installation Manual for additional Forward-Facing installation instructions.
See page 40-45 in the Installation Manual for Forward-Facing with LATCH instructions.
INSTALLATION
CHECKLIST
See page 21 in the Installation Manual for complete installation instructions
READ YOUR MANUAL.
Always read your car seat manual prior to installing your car seat. Your car seat
manufacturer should be your primary resource for information regarding your car seat.
INSTALLATION SHOULD BE TIGHT.
Car seats should not move more than 1” (2.5 cm) at the belt path.
CHECK THE LEVEL INDICATOR IN REAR-FACING MODE.
PLACE CHEST CLIP AT ARMPIT LEVEL.
Not too high or too low.
CHECK HARNESS HEIGHT.
REAR-FACING: Harness straps should be at or below the child’s shoulders.
FORWARD-FACING: Harness straps should be at or above the child’s shoulders.
PERFORM THE PINCH TEST IN THE SHOULDER AREA TO MAKE SURE
THE HARNESS IS TIGHT ENOUGH.
It is important that the harness is snug against your child’s body.
CHECK INSTALLATION OFTEN.
Regularly inspect your seat’s installation to ensure it is still tight and secure.
">

Hello! I am an AI chatbot specifically trained to assist you with the Baby Jogger city turn Quick start Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Rear-facing & forward-facing installation
Tether for extra safety
Recline foot adjustment
Rapidlock mechanism
Level indicator
Cup holder
Instruction manual storage
Harness & headrest adjustment

Frequently asked questions

Check the level indicator in rear-facing mode. It should be in the blue zone. Make sure the seat doesn't move more than 1 inch at the belt path.

Squeeze the recline lever and lift the base to extend or retract the foot. Select position 1-3 depending on your child's weight and whether the seat is rear-facing or forward-facing.

It's a mechanism that secures the seat belt to the car seat. It should click into place when closed. Do not lock the seat belt.

For children over 40 lb, use recline position 1. For children under 40 lb, use recline position 3. Refer to the manual for specific weight limits.