Universal Pumps UP-GPP600 Instruction Manual

Universal Pumps UP-GPP600 is a general-purpose garden water pump suitable for domestic water transfer applications. It's designed to move water efficiently from sources like tanks or wells to your garden, taps, or other household needs. The pump is powerful with a max flow of 2,800L/Hr and a max head of 35m. It's easy to install and operate, with clear instructions and safety warnings for your protection.

PDF Download

Document

INSTRUCTION MANUAL
UP-GPP600 &amp; UP-GPP600A
UP-GPP600
UP-GPP600A
Protect yourself and others by observing all safety information, warnings, and cautions. Failure to
comply with instructions could result in personal injury and/or damage to product or property.
Please retain instructions for future reference.
UP-GPP650
PERFORMANCE GRAPH
DESCRIPTION
General purpose garden water pumps for use in domestic situations for water transfer applications. The
UP-GPP600A has the additional feature of automatic ON / OFF control based on pressure and flow.
Not for use with chemical or flammable liquids.
PRODUCT SPECIFICATION
Models: UP-GPP600 &amp; UP-GPP600A
Input: 230V ~ 50Hz
Power Rating: 600W
Protection: IPX4
Max. Flow: 2,800L/Hr
Max. Head: 35m
Max. Suction Depth: 7m
Power cord length 1.2m
KNOW YOUR PRODUCT
3
D
A
C
2
B
3
2
D
4
1
1
5
UP-GPP600
1. Water Inlet
2. Inlet strainer
3. Water Outlet
4. ON / OFF Switch
5. Pump housing drain plug.
A. Automatic controller
B. Status lamps
C. Reset switch
E. Pressure gauge (Not visible)
D. Service switch. (Must be ON at all times)
UP-GPP600A
5
SAFETY
IMPORTANT
Please read all of the safety and operating instructions carefully before using this product. Please pay
particular attention to all sections of this manual that carry warning symbols
SAFETY WARNING FOR PUMPS
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
WARNING! Do not use in swimming pools or spas.
WARNING! Always use an electrical outlet that is protected by Residual Current
Device RCD (Safety switch) with a trip current of 30mA or less.
WARNING! This product is intended for pumping water in a home domestic
application. Do not use it for corrosive, abrasive, explosive or dangerous liquids. Fluids other than
water will damage the water pump and/or create a fire hazard.
WARNING! DO NOT ABUSE THE MAINS LEAD
• Never pull the mains lead to disconnect the pump from the mains socket.
• Keep the mains lead away from heat, oil and sharp edges.
• If you have to use an extension lead with this product, it must be designed for outdoor use.
CAUTION! Do not run the pump without water or allow the pump to run dry. This
will damage the pump’s seal and void the warranty
CAUTION! This pump is not suitable for drinking water. Some lubricants and other
materials used in the pump may leach into the water.
CAUTION! Do not place the suction line in mud or sludge. They can block the inlet and
cause the pump to overheat.
CAUTION! Do not use this pump as a mains pressure booster pump. This may cause
the pump body to crack and will void warranty.
CAUTION! The pump MUST be protected from the elements. The pump must be
protected by a cover or similar.
PREPARATION TYPICAL SETUP
NOTE: IT IS NOT RECOMMENDED TO USE AN EXTENSION CORD WITH
THESE PUMPS. If you have to use an extension lead with this product, it must be
designed for outdoor use.
UP-GPP600 and UP-GPP600A Typical setup with base level
of tank at same level as the pump.
Outlet Pipe to
garden tap
Gate Valve
Tank
Inlet
Solid Base
Fig 1.
UP-GPP600 and UP-GPP600A Typical set up with base
level of tank below the pump.
Outlet Pipe to
garden tap
Gate Valve
Inlet
Solid Base
Fig 2.
Foot Valve
This is a one way valve to stop
water back flowing into the tank
Tank
ENVIRONMENT
CAUTION! The pump must be protected from the elements. These pumps are not
designed to be exposed to the elements. They must be protected by a cover or similar with ventilation.
Under the eave of a house is NOT considered being protected. Failure to protect the pump from the
elements will void the warranty.
PREPARATION
WARNING! Always use an electrical outlet that is protected by Residual Current
Device RCD (Safety switch) with a trip current of 30mA or less.
Before the pump can be used the pump body must be primed before use and will depend on the type of
installation.
1. Setup with base level of tank at same level (Fig 1.)
• Open the gate valve and the garden tap.
• Run the pump until there is no air visible in the clear cover of the inlet strainer.
• Close the garden tap and turn the pump OFF
2. Setup with base level of tank below the pump. (Fig 2.)
• Check that the pump is turned OFF at the mains outlet. (Power point)
• With the gate valve open, unscrew the clear cover of the strainer, fill with water until the suction line and
pump body are filled with water.
• Replace the cover.
NOTE: A FOOT VALVE MUST BE FITTED OR THE WATER WILL DRAIN
BACK INTO THE TANK. This may lead to having to prime the pump continually.
• Check that the ON / OFF switch (service switch) is in the ON position.
• Turn the power ON at the mains outlet (Power point)
• The pump should start.
• Slowly open the outlet taps and allow the lines to clear and purge any air in the pipes.
• This priming procedure may need to be repeated several times.
• After successfully priming the pump turn the garden tap OFF and check for leaks and rectify.
NOTE: FOR THE UP-GPP600A. This model is fitted with a automatic controller
that will try to prime the pump two times only. If the controller detects that the pump is
still not primed after the two attempts it will turn off and the failure lamp will FLASH.
To RESET the controller re-prime the pump and press the reset button to try again.
OPERATION
UP-GPP600 (Manual ON / OFF model)
• With the pump primed, Turn the pump ON at the power switch and power point.
• Turn the garden tap on and use the water as required.
• When finished turn the garden tap OFF
• Turn the power to the pump OFF
UP-GPP600A (With automatic controller)
• With the pump primed,
• Check that the service switch is in the ON position and that the mains power is connected to the pump.
• Open the garden tap.
• The pump should automatically start.
• Use the water as required.
• Turn the garden tap OFF and the pump should stop after a short delay
CLEANING AND MAINTENANCE
WARNING! Check that the pump is unplugged from the mains supply and gate
valve is turned OFF before preforming any cleaning or maintenance on the pump.
• These pumps should require no maintenance other than regular cleaning.
• Do not attempt to repair the pump yourself, repairs must be carried out by an authorized service centre.
• Check the pump regularly to ensure the inlet strainer is clear of leaves or other debris.
TROUBLE SHOOTING
FAULT
The pump starts and stops
irregularly or continuously.
(UP-GPP600A only)
Not enough water being
pumped.
Pump does not run
The pump runs but does
not deliver water
POSSIBLE CAUSE
Leak on the discharge line or outlets.
A) Dirty inlet strainer.
B) Air in pump housing.
C) Water level low.
SOLUTIONS
Fix any leaks.
A) Clean strainer.
B) Release air via priming plug
and fix any air leaks on suction
line.
C) Check that the suction line is
completely under water level.
A) No mains voltage.
A) check power supply is on and
B) Shaft locked.
connected.
C) Pump not primed (UP-GPP600A only) B) Disconnect pump from power
supply and clear blockage.
C) Check the power/service
switch on the pump is ON.
D) Check Failure lamp and prime
the pump (UP-GPP600A only)
A) Air in pump housing.
A) Prime the pump.
B) Air in suction pipe.
B) Check that suction pipe and
C) Intake valve not in water.
fittings are tight.
D) Intake valve closed or clogged.
C) Put intake into the water.
E) Max suction depth exceeded.
D) Open intake valve or remove
blockage.
E) Check suction depth.
WARRANTY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
This product is covered by a 24 month warranty.
This warranty will not apply:
(i) where this product has been subjected to misuse, abuse, accident or want of care;
(ii) where this product has been used for a purpose for which it was not designed or is not suited;
(iii) where the service of this product has been undertaken by a non-authorised person or company or if
non approved parts have been used;
(iv) where this product has been used for industrial purposes.
Should service become necessary during the warranty period, the purchaser should contact an Authorised
Service centre of White International. In order to obtain warranty service, the purchaser must present the
store receipt showing the name of the retailer and the date of purchase.
The period of the warranty begins from the original date of purchase, notwithstanding any subsequent repair
or parts replacement.
Purchaser shall be responsible for all transport charges to and from the Authorised Service Centre.
Damage in transit is not covered by this warranty.
The purchaser should remove from the product any liquids (if applicable) before sending the tool for service
or repair. The tool should be packed securely to prevent damage.
WARRANTY EXCLUSIONS
Wear parts or service related parts required when performing normal and regular maintenance of this
product are not covered by warranty unless it is found to be defective by an Authorised Service Centre.
These include, but are not limited to: Power cords and seals.
Distributed in Australia by White International.
PO Box 304 Milperra LPO, NSW Australia, 2214
Ph:1800 251 338
The White International is one of continuous improvement and the company reserves the right to alter
designs, colours and specifications without notice.
">

Hello! I am an AI chatbot specifically trained to assist you with the Universal Pumps UP-GPP600 Instruction Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key Features

230V ~ 50Hz
600W
IPX4
Max. Flow: 2,800L/Hr
Max. Head: 35m
Max. Suction Depth: 7m
Automatic ON/OFF control (UP-GPP600A)
Easy Priming

Frequently asked questions

How do I prime the UP-GPP600 pump?

It depends on your set up. For a tank at the same level as the pump, open the gate valve and garden tap, run the pump until air is gone. For a tank below the pump, fill the suction line with water, replace the strainer cover, open the gate valve, and turn the pump ON.