xE910 Mini PCIe Hardware User Guide

xE910 Mini PCIe Hardware User Guide

1vv0301006 Rev.10 – 2015-12-06


1vv0301006 Rev.10 – 2015-12-06

APPLICABILITY TABLE

PRODUCT

HE910 Mini PCIe

HE910-D Mini PCIe

DE910 Mini PCIe

LE910-SVG Mini PCIe

LE910-NVG Mini PCIe

LE910-NAG Mini PCIe

LE910-EUG Mini PCIe

LE910-NA V2 Mini PCIe

LE910-SV V2 Mini PCIe

LE910-EU V2 Mini PCIe

LE910-AU V2 Mini PCIe

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 2 of 56


1vv0301006 Rev.10 – 2015-12-06

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

Notice

While reasonable efforts have been made to assure the accuracy of this document,

Telit assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein. The information in this document has been carefully checked and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies or omissions. Telit reserves the right to make changes to any products described herein and reserves the right to revise this document and to make changes from time to time in content hereof with no obligation to notify any person of revisions or changes. Telit does not assume any liability arising out of the application or use of any product, software, or circuit described herein; neither does it convey license under its patent rights or the rights of others.

It is possible that this publication may contain references to, or information about Telit products (machines and programs), programming, or services that are not announced in your country. Such references or information must not be construed to mean that

Telit intends to announce such Telit products, programming, or services in your country.

Copyrights

This instruction manual and the Telit products described in this instruction manual may be, include or describe copyrighted Telit material, such as computer programs stored in semiconductor memories or other media. Laws in the Italy and other countries preserve for Telit and its licensors certain exclusive rights for copyrighted material, including the exclusive right to copy, reproduce in any form, distribute and make derivative works of the copyrighted material. Accordingly, any copyrighted material of Telit and its licensors contained herein or in the Telit products described in this instruction manual may not be copied, reproduced, distributed, merged or modified in any manner without the express written permission of Telit. Furthermore, the purchase of Telit products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Telit, as arises by operation of law in the sale of a product.

Computer Software Copyrights

The Telit and 3rd Party supplied Software (SW) products described in this instruction manual may include copyrighted Telit and other 3rd Party supplied computer programs stored in semiconductor memories or other media. Laws in the Italy and other countries preserve for Telit and other 3rd Party supplied SW certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Telit or other

3rd Party supplied SW computer programs contained in the Telit products described in this instruction manual may not be copied (reverse engineered) or reproduced in any manner without the express written permission of Telit or the 3rd Party SW supplier.

Furthermore, the purchase of Telit products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Telit or other 3rd Party supplied SW, except for the normal nonexclusive, royalty free license to use that arises by operation of law in the sale of a product.



1vv0301006 Rev.10 – 2015-12-06

Usage and Disclosure Restrictions

License Agreements

The software described in this document is the property of Telit and its licensors. It is furnished by express license agreement only and may be used only in accordance with the terms of such an agreement.

Copyrighted Materials

Software and documentation are copyrighted materials. Making unauthorized copies is prohibited by law. No part of the software or documentation may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without prior written permission of

Telit

High Risk Materials

Components, units, or third-party products used in the product described herein are

NOT fault-tolerant and are NOT designed, manufactured, or intended for use as on-line control equipment in the following hazardous environments requiring fail-safe controls: the operation of Nuclear Facilities, Aircraft Navigation or Aircraft Communication

Systems, Air Traffic Control, Life Support, or Weapons Systems (High Risk Activities").

Telit and its supplier(s) specifically disclaim any expressed or implied warranty of fitness for such High Risk Activities.

Trademarks

TELIT and the Stylized T Logo are registered in Trademark Office. All other product or service names are the property of their respective owners.

Copyright © Telit Communications S.p.A.



1vv0301006 Rev.10 – 2015-12-06

Contents

1.

INTRODUCTION ........................................................................................................................................................... 7

1.1.

S

COPE

....................................................................................................................................................................... 7

1.2.

A

UDIENCE

................................................................................................................................................................. 7

1.3.

C

ONTACT

I

NFORMATION

, S

UPPORT

........................................................................................................................... 7

1.4.

T

EXT

C

ONVENTIONS

................................................................................................................................................. 8

1.5.

R

ELATED

D

OCUMENTS

............................................................................................................................................. 8

2.

OVERVIEW .................................................................................................................................................................... 9

3.

XE910 MINI PCI EXPRESS CARD CONNECTIONS............................................................................................. 10

3.1.

PIN-OUT ................................................................................................................................................................ 10

3.2.

A

NTENNA

C

ONNECTORS

......................................................................................................................................... 12

4.

POWER SUPPLY ......................................................................................................................................................... 13

4.1.

P

OWER

S

UPPLY

R

EQUIREMENTS

............................................................................................................................. 13

4.2.

P

OWER

C

ONSUMPTION

............................................................................................................................................ 14

5.

GSM/WCDMA/LTE /CDMA RADIO SECTION ..................................................................................................... 15

5.1.

X

E910 M

INI

PCI P

RODUCT

V

ARIANTS

.................................................................................................................... 15

5.2.

TX

AND

RX

CHARACTERISTICS

............................................................................................................................... 15

5.3.

GSM/WCDMA/LTE/CDMA A

NTENNA

R

EQUIREMENTS

...................................................................................... 16

5.3.1.

GSM/WCDMA/LTE/CDMA Antenna - Installation Guidelines ..................................................................... 19

5.4.

A

NTENNA

D

IVERSITY

R

EQUIREMENTS

.................................................................................................................... 21

5.5.

GNSS R

ECEIVER

..................................................................................................................................................... 24

5.5.1.

GNSS Performances ...................................................................................................................................... 24

5.5.2.

GNSS RF Front End Design .......................................................................................................................... 25

6.

LOGIC LEVEL SPECIFICATIONS .......................................................................................................................... 26

7.

USB PORT ..................................................................................................................................................................... 26

7.1.

USB 2.0

HS ............................................................................................................................................................ 26

8.

SIM INTERFACE ........................................................................................................................................................ 27

9.

CONTROL SIGNALS .................................................................................................................................................. 28

9.1.

WAKE# .................................................................................................................................................................. 28

9.2.

W_DISABLE# ....................................................................................................................................................... 30

9.3.

LED_WWAN# ....................................................................................................................................................... 30

9.4.

PERST# .................................................................................................................................................................. 31

10.

AUDIO SECTION OVERVIEW ............................................................................................................................ 31

10.1.

E

LECTRICAL

C

HARACTERISTICS

............................................................................................................................. 32

10.2.

CODEC E

XAMPLE

.................................................................................................................................................. 32

11.

MECHANICAL SPECIFICATIONS ..................................................................................................................... 33

11.1.

WEIGHT ................................................................................................................................................................ 34

11.2.

ENVIRONMENTAL REQUIREMENTS .............................................................................................................. 34

12.

PACKING SYSTEM ................................................................................................................................................ 35

13.

SAFETY RECOMMANDATIONS ......................................................................................................................... 36



1vv0301006 Rev.10 – 2015-12-06

14.

CONFORMITY ASSESSMENT ISSUES .............................................................................................................. 37

14.1.

1999/5/EC D

IRECTIVE

(HE910) .............................................................................................................................. 37

14.2.

FCC/IC R

EGULATORY NOTICES

(HE910) ............................................................................................................... 40

14.3.

1999/5/EC D

IRECTIVE

(LE910) .............................................................................................................................. 42

14.4.

FCC/IC R

EGULATORY NOTICES

(LE910) ................................................................................................................ 45

14.5.

C

ONFORMITY

A

SSESSMENT

I

SSUES

/ P

ROBLÈMES D

'

ÉVALUATION DE CONFORMITÉ

(DE910) ................................. 48

14.6.

CONFORMITY ASSESSMENT ISSUES (LE910 V2) ......................................................................................... 50

14.6.1.

FCC/IC Regulatory notices ........................................................................................................................... 50

14.7.

S

AFETY

R

ECOMMENDATIONS

(LE910 V2) .............................................................................................................. 54

14.8.

S

AFETY

R

ECOMMENDATIONS

(HE910) ................................................................................................................... 55

14.9.

S

AFETY

R

ECOMMENDATIONS

(DE910) ................................................................................................................... 55

15.

DOCUMENT HISTORY ......................................................................................................................................... 56



1vv0301006 Rev.10 – 2015-12-06

1. Introduction

1.1.

1.2.

1.3.

Scope

The aim of this document is the description of some hardware solutions useful for developing a product with the Telit xE910 Mini PCIe Adapter.

Audience

This document is intended for Telit customers, who are integrators, about to implement their applications using our xE910 Mini PCIe Adapter.

Contact Information, Support

For general contact, technical support, to report documentation errors and to order manuals, contact Telit’s Technical Support Center (TTSC) at:

[email protected]

[email protected]

[email protected]

[email protected]

Alternatively, use: http://www.telit.com/en/products/technical-support-center/contact.php

For detailed information about where you can buy the Telit modules or for recommendations on accessories and components visit: http://www.telit.com

To register for product news and announcements or for product questions contact

Telit’s Technical Support Center (TTSC).

Our aim is to make this guide as helpful as possible. Keep us informed of your comments and suggestions for improvements.

Telit appreciates feedback from the users of our information.


1.4.

1.5. xE910 Mini PCIe Hardware User Guide

1vv0301006 Rev.10 – 2015-12-06

Text Conventions

Danger – This information MUST be followed or catastrophic equipment failure or bodily injury may occur.

Caution or Warning – Alerts the user to important points about integrating the module, if these points are not followed, the module and end user equipment may fail or malfunction.

Tip or Information – Provides advice and suggestions that may be useful when integrating the module.

All dates are in ISO 8601 format, i.e. YYYY-MM-DD.

Related Documents

•

HE910/UE910 AT Commands Reference Guide 80378ST10091a

•

HE910 Hardware User Guide 1vv03700925

•

Event Monitor Application Note

•

Digital Voice Interface Application Note

•

LE910 AT Commands Reference Guide

•

LE910 Hardware User Guide

80000nt10043a

80000NT10004a

80378ST10585a

1vv03701089

•

LE910 Digital Voice Interface Application Note 80000NT11246a

•

DE910 Hardware User Guide 1vv03700951

•

LE910-V2 Modules AT Commands Reference Guide 80446ST10707A

•

LE910-V2 Hardware User Guide 1VV0301200



1vv0301006 Rev.10 – 2015-12-06

2. Overview

The aim of this document is the description of some hardware solutions useful for developing a product that will host the Telit XE910 Mini PCIe Adapter.

In this document all the basic functions of a mobile phone will be taken into account; for each one of them a proper hardware solution will be suggested and eventually the wrong solutions and common errors to be avoided will be evidenced. Obviously this document cannot embrace the whole hardware solutions and products that may be designed. The wrong solutions to be avoided shall be considered as mandatory, while the suggested hardware configurations shall not be considered mandatory, instead the information given shall be used as a guide and a starting point for properly developing your product with the Telit Mini PCIe module.

NOTICE:

(EN) The integration of the GSM/GPRS/WCDMA

XE910 Mini PCIe

cellular module within user application shall be done according to the design rules described in this manual.

(IT) L’integrazione del modulo cellulare GSM/GPRS/WCDMA

XE910 Mini PCIe

all’interno dell’applicazione dell’utente dovrà rispettare le indicazioni progettuali descritte in questo manuale.

(DE) Die Integration des

XE910 Mini PCIe

GSM/GPRS/WCDMA Mobilfunk-Moduls in ein Gerät muß gemäß der in diesem Dokument beschriebenen Kunstruktionsregeln erfolgen.

(SL) Integracija GSM/GPRS/WCDMA

XE910 Mini PCIe

modula v uporabniški aplikaciji bo morala upoštevati projektna navodila, opisana v tem priro čniku.

(SP) La utilización del modulo GSM/GPRS/WCDMA

XE910 Mini PCIe

debe ser conforme a los usos para los cuales ha sido deseñado descritos en este manual del usuario.

(FR) L’intégration du module cellulaire GSM/GPRS/WCDMA

XE910 Mini PCIe

dans l’application de l’utilisateur sera faite selon les règles de conception décrites dans ce manuel.

(HE)

XE910 Mini PCIe

The information presented in this document is believed to be accurate and reliable. However, no responsibility is assumed by Telit Communications S.p.A. for its use, nor any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent rights of Telit Communications S.p.A. other than for circuitry embodied in Telit products. This document is subject to change without notice.



1vv0301006 Rev.10 – 2015-12-06

3. xE910 Mini PCI express card connections

3.1. PIN-OUT

This product has a standard Mini PCI express connector, excepting the (4) audio signals which use normally reserved connectors.

Pin Signal

Power Supply

2

3V3_AUX

24

3V3

39

3V3_AUX

41

3V3_AUX

52

3V3_AUX

4

GND

9

GND

15

GND

18

GND

21

GND

26

GND

27

GND

29

GND

34

GND

35

GND

37

GND

40

GND

43

GND

50

GND

SIM Card Interface

8

SIMVCC

10

SIMIO

12

SIMCLK

14

SIMRST

USB

36

USB D-

38

USB D+

I/O Function

Ground

Ground

Ground

Ground

Ground

Ground

Ground

Ground

3.3V supply

3.3V supply

3.3V supply

3.3V supply

3.3V supply

Ground

Ground

Ground

Ground

Ground

Ground

-

-

-

-

-

-

-

-

-

-

O

-

-

-

-

O

O

O

O

O External SIM signal – Power supply for the SIM

I/O External SIM signal - Data I/O

O

O

External SIM signal – Clock

External SIM signal – Reset

I/O USB differential Data (-)

I/O USB differential Data (+)

Type

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

Power

1.8 / 3V

1.8 / 3V

1.8 / 3V

1.8 / 3V

0.3…2.8V

0.3…2.8V

Pi n

Signal I/O Function Type



1vv0301006 Rev.10 – 2015-12-06

Miscellaneous Functions

1

WAKE# O Active low signal used to wake up the system from stand-by 3.3V

32

33

44

46

48

13

16

17

19

23

25

28

30

31

20

22

42

WDISABLE#

PERST#

LED_WWAN#

I

I

O

Active low signal for wireless disabling (Flight mode) 3.3V

Active low functional reset to the card 3.3V

Active low, open drain signal for WWAN LED driving, used to provide

3.3V…5V module’s status indication

Digital Voice Interface (DVI)

45

PCM_CLK

47

PCM_RX

I/O

I

Digital Audio Interface (CLK)

Digital Audio Interface (RX)

CMOS 1.8V

CMOS 1.8V

49

51

PCM_TX

PCM_SYNC

N.C.

3

O Digital Audio Interface (TX)

I/O Digital Audio Interface (SYNC)

-

-

CMOS 1.8V

CMOS 1.8V

5

6

7

11

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-



1vv0301006 Rev.10 – 2015-12-06

Antenna Connectors

The xE910 Mini PCIe adapter is equipped with a set of

50 Ω RF U.FL. connectors from

Hirose U.FL-R-SMT-1(10).

The available connectors are:

•

Main RF antenna (ANT)

•

RX Diversity Antenna (DIV)

•

GNSS Antenna (GPS)

See the picture on the right for their position on the interface.

The presence of all the connectors is depending on the product characteristics and supported functionalities.

For more information about mating connectors, visit the website http://www.hirose-connectors.com/



1vv0301006 Rev.10 – 2015-12-06

4. Power Supply

4.1.

The power supply circuitry and board layout are a very important part in the full product design and they strongly reflect on the product overall performances, hence read the requirements carefully and the guidelines that will follow for a proper design.

Power Supply Requirements

The external power supply must be connected to the pins 2, 39, 41, 52 and must fulfill the following requirements:

POWER SUPPLY

Nominal Supply Voltage

Normal Operating Voltage Range

3.3 V

3.00 V÷ 3.60 V

NOTE:

The Operating Voltage Range MUST never be exceeded; care must be taken when designing the application’s power supply section to avoid having an excessive voltage drop.

If the voltage drop is exceeding the limits it could cause a Power Off of the module.

NOTE:

Overshoot voltage (regarding MAX Operating Voltage) and drop in voltage (regarding

MIN Operating Voltage) MUST never be exceeded;



1vv0301006 Rev.10 – 2015-12-06

Power Consumption

Please refer to the Module’s Hardware User guide for the details

The GSM system is made in a way that the RF transmission is not continuous, else it is packed into bursts at a base frequency of about 216 Hz, and the relative current peaks can be as high as about 2.4A. Therefore the power supply has to be designed in order to withstand with these current peaks without big voltage drops; this means that both the electrical design and the board layout must be designed for this current flow. If the voltage drop during the peak current absorption is too much, then the device may even shutdown as a consequence of the supply voltage drop.

NOTE:

The electrical design for the Power supply should be made ensuring it will be capable of a peak current output of at least 2.4 A.



1vv0301006 Rev.10 – 2015-12-06

5. GSM/WCDMA/LTE /CDMA Radio Section

5.1. xE910 Mini PCI Product Variants

The following table is listing the main differences between the xE910 variants:

Product

LE910-NA V2

LE910-SV V2

LE910-EU V2

LE910-AU V2

2G Bands

Not supported

Not supported

GSM 900,

DCS1800

Not supported

3G Bands

B5, B2

Not supported

B1, B8

Not supported

LTE Bands

B2, B4, B5,

B12/B17 (B13)

B2, B4, B13

B3, B7, B20, B1,

B8

B3, B7, B28

CDMA Bands GNSS

NO

NO

NO

NO

NO

NO

NO

NO

LE910-EUG

GSM 900,

DCS1800

B5(850), B8

(900), B1

(2100)

B20 (800), B3

(1800), B7 (2600)

NO YES

LE910-NAG

GSM 850,

PCS 1900

B5(850),

B2(1900)

B17(700), B5(850),

B4(1700),

B2(1900)

NO YES

LE910-NVG

Not supported

B5(850),

B2(1900)

B13(700),

B4(1700)

NO YES

LE910-SVG

Not supported

B13(700),

B4(1700)

NO YES

HE910

HE910-D

DE910-DUAL

Not supported

GSM 850,

GSM 900,

DCS1800,

PCS 1900

GSM 850,

GSM 900,

DCS1800,

PCS 1900

Not supported

FDD B1, B2,

B4, B5, B8

FDD B1, B2,

B4, B5, B8

Not supported

Not supported

Not supported

Not supported

NO

NO

BC0, BC1

YES

NO

YES

5.2. TX and RX characteristics




1vv0301006 Rev.10 – 2015-12-06

5.3. GSM/WCDMA/LTE/CDMA Antenna Requirements

The antenna connection is one of the most important aspect in the full product design as it strongly affects the product overall performances, hence read carefully and follow the requirements and the guidelines for a proper design.

The xE910 Mini PCIe adapter is provided with three RF connectors.

The available connectors are:

•

Main RF antenna (ANT)

•

RX Diversity Antenna (DIV)

•

GNSS Antenna (GPS)

Connecting cables between the module and the antenna must have 50

Ω impedance.

If the impedance of the module is mismatched, RF performance is reduced significantly.

If the host device is not designed to use the module’s diversity or GPS antenna, terminate the interface with a

50Ω load.

MAIN ANTENNA REQUIREMENTS for LE910-NA V2

Frequency range

Bandwidth

Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for that/those band(s)

140 MHz in LTE/WCDMA Band 2

445 MHz in LTE Band 4


80 MHz in LTE Band 8 / GSM900



42 MHz in LTE band 17

Impedance

50 ohm

Input power

VSWR absolute max

> 24dBm Average power in WCDMA & LTE

≤ 10:1 (limit to avoid permanent damage)

VSWR recommended

≤ 2:1 (limit to fulfil all regulatory requirements)

MAIN ANTENNA REQUIREMENTS for LE910-AU V2

Frequency range


Bandwidth




50 ohm

Impedance

Input power








1vv0301006 Rev.10 – 2015-12-06

MAIN ANTENNA REQUIREMENTS for LE910-EU V2

Frequency range


Bandwidth

Impedance


170 MHz in LTE/WCDMA Band 3 / DCS1800


80 MHz in LTE/WCDMA Band 8 / GSM900


50 ohm

Input power






MAIN ANTENNA REQUIREMENTS for LE910-EUG

Frequency range

Bandwidth (GSM/EDGE)

Bandwidth

(WCDMA)


GSM900 : 80 MHz

GSM1800(DCS) : 170 MHz

WCDMA band I(2100) : 250 MHz

WCDMA band V(850) : 70 MHz

WCDMA band VIII(900) : 80 MHz

Bandwidth

(LTE)

LTE band III(1800) : 170 MHz

LTE Band VII(2600) : 190 MHz

LTE Band XX(800) : 71 MHz

Impedance

50 ohm

Input power


> 33dBm(2 W) peak power in GSM







1vv0301006 Rev.10 – 2015-12-06

MAIN ANTENNA REQUIREMENTS for LE910-NAG

Frequency range


Bandwidth

(WCDMA)

Bandwidth

(LTE)


GSM850 : 70 MHz

GSM1900(PCS) : 140 MHz

WCDMA band II(1900) : 140 MHz


LTE Band II(1900) : 140 MHz

LTE Band IV(1700) : 445 MHz

LTE Band V (850) : 70 MHz

LTE Band XVII(700) : 42 MHz

Impedance

50 ohm

Input power







MAIN ANTENNA REQUIREMENTS for LE910-NVG

Frequency range

Bandwidth

(WCDMA)




Bandwidth

(LTE)


LTE Band XIII(700) : 41 MHz

Impedance

50 ohm

Input power






MAIN ANTENNA REQUIREMENTS for LE910-SVG

Frequency range

Bandwidth

(LTE)

Impedance




50 ohm

Input power


> 24dBm Average power





5.3.1.


1vv0301006 Rev.10 – 2015-12-06

MAIN ANTENNA REQUIREMENTS for HE910

Frequency range



70 MHz in GSM850, 80 MHz in GSM900, 170 MHz in DCS & 140

MHz PCS band

Bandwidth

(WCDMA)

70 MHz in WCDMA Band V

80 MHz in WCDMA Band VIII

460 MHz in WCDMA Band IV

140 MHz in WCDMA Band II

250 MHz in WCDMA Band I

Impedance

50 ohm

Input power



> 24dBm Average power in WCDMA




MAIN ANTENNA REQUIREMENTS for DE910-DUAL

Frequency range

Bandwidth


70 MHz in CDMA BC0

140 MHz in CDMA BC1

Gain

Gain < 5.12dBi in CDMA BC0

Gain < 6.12dBi in CDMA BC1

Impedance

50 ohm

Input power


> 24.4dBm Average Power in CDMA

≤ 5:1 (Limit to avoid permanent damage)




GSM/WCDMA/LTE/CDMA Antenna - Installation Guidelines

•

Install the antenna in a place covered by the GSM/WCDMA/LTE/CDMA signal.

•

If the device antenna is located greater then 20cm from the human body and there are no co-located transmitters then the Telit FCC/IC approvals can be re-used by the end product

•

If the device antenna is located less than 20cm from the human body or there are no co-located transmitters then the additional FCC/IC testing may be required for the end product (Telit FCC/IC approvals cannot be reused)

•

Antenna shall not be installed inside metal cases

•

Antenna shall be installed also according antenna manufacturer instructions.



1vv0301006 Rev.10 – 2015-12-06



1vv0301006 Rev.10 – 2015-12-06

5.4. Antenna Diversity Requirements

This product includes an input for a second RX antenna to improve the radio sensitivity.

The function is called Antenna Diversity.

DIVERSITY ANTENNA REQUIREMENTS for LE910-NA V2

Frequency range





35 MHz in LTE Band 8 / GSM900

Bandwidth



12 MHz in LTE band 17

Impedance

50 ohm



DIVERSITY ANTENNA REQUIREMENTS for LE910-SV V2

Frequency range



Bandwidth



Impedance

50 ohm



DIVERSITY ANTENNA REQUIREMENTS for LE910-AU V2

Frequency range


Bandwidth




Impedance

50 ohm





1vv0301006 Rev.10 – 2015-12-06

DIVERSITY ANTENNA REQUIREMENTS for LE910-EU V2

Frequency range


Bandwidth


75 MHz in LTE/WCDMA Band 3 / DCS1800


35 MHz in LTE/WCDMA Band 8 / GSM900


Impedance

50 ohm



DIVERSITY ANTENNA REQUIREMENTS for LE910-EUG

Frequency range

Bandwidth

(WCDMA)

Bandwidth

(LTE)


WCDMA band I(2100) : 250 MHz


WCDMA band VIII(900) : 80 MHz

LTE band III(1800) : 170 MHz

LTE Band VII(2600) : 190 MHz

LTE Band XX(800) : 71 MHz

Impedance

50 ohm



DIVERSITY ANTENNA REQUIREMENTS for LE910-NAG

Frequency range

Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for

Bandwidth

(WCDMA)

that/those band(s)



Bandwidth

(LTE)

LTE Band II(1900) : 140 MHz


LTE Band V (850) : 70 MHz

LTE Band XVII(700) : 42 MHz

Impedance

50 ohm





1vv0301006 Rev.10 – 2015-12-06

DIVERSITY ANTENNA REQUIREMENTS for LE910-NVG

Frequency range


Bandwidth

(WCDMA)



Bandwidth

(LTE)



Impedance

50 ohm



DIVERSITY ANTENNA REQUIREMENTS for LE910-SVG

Frequency range


Bandwidth

(LTE)



Impedance

50 ohm



DIVERSITY ANTENNA REQUIREMENTS for HE910

Frequency range



70 MHz in GSM850, 80 MHz in GSM900 & 140 MHz PCS band

Bandwidth

(WCDMA)

70 MHz in WCDMA Band V

80 MHz in WCDMA Band VIII

140 MHz in WCDMA Band II

250 MHz in WCDMA Band I

Impedance

50 ohm



DIVERSITY ANTENNA REQUIREMENTS for DE910-DUAL

Frequency range


Bandwidth

70 MHz in CDMA BC0

140 MHz in CDMA BC1

Impedance

50 ohm





1vv0301006 Rev.10 – 2015-12-06

The second Rx antenna should not be located in the close vicinity of main antenna. In order to improve Diversity Gain, Isolation and reduce mutual interaction, the two antennas should be located at the maximum reciprocal distance possible, taking into consideration the available space in the application.

NOTE1:

On HE910 the diversity is not supported on the FDD BAND IV and DCS band.

NOTE2:

In case of HE910, if the RX Diversity is not used/connected, disable the Diversity functionality using the AT#RXDIV command (ref to the At User guide for the proper syntax).

GNSS Receiver

The XE910 Mini PCIe adapter integrates a GNSS receiver that could be used in

Standalone mode and in A-GPS (assisted GPS), according to the different configurations.

The supported technologies are described in the following table:

Product GPS GLONASS

LE910-EUG

YES YES

LE910-NAG

LE910-NVG

YES YES

LE910-SVG

YES

YES

YES

YES

HE910

HE910-D

DE910-DUAL

YES

NO

YES

NO

NO

YES

LE910-NA V2

LE910-SV V2

LE910-EU V2

LE910-AU V2

NO

NO

NO

NO

NO

NO

NO

NO

5.5.1. GNSS Performances



5.5.2.


1vv0301006 Rev.10 – 2015-12-06

GNSS RF Front End Design

The xE910 Mini PCIe adapter contains an integrated LNA and pre-select SAW filter.

This allows the module to work well with a passive GPS antenna. If the antenna cannot be located near the xE910, then an active antenna (that is, an antenna with a low noise amplifier built in) can be used with an external dedicated power supply circuit.

NOTE:

Please refer to the Module’s Hardware User Guide for detailed information about GPS operating modes and RF signal requirements.



1vv0301006 Rev.10 – 2015-12-06

6. Logic level specifications

The following table shows logic level specifications used in the xE910 interface circuits:

Absolute Maximum Ratings -Not Functional

Parameter Min Max

Input level on any digital pin (CMOS 1.

with respect to ground

-0.5V 3.6V

Operating Range – DC Specification for 3V3 Logic Signalling

Symbol Parameter Min Max

3V3, 3V3_AUX

V

IH

V

IL

V

OH

V

OL

I

IN

I

OL

Supply voltage

Input high level

Input low level

Output high level

Output low level

Input Leakage

Current

Output Low Current for open-drain signals

3.0V

2.0V

-0.5V

2.0V

-0.5V

-10µA

4mA

3.6V

3.6V

0.8V

3.6V

0.8V

10µA

7. USB Port

7.1.

The xE910 Mini PCIe adapter includes one integrated universal serial bus (USB) transceiver, compliant with the standard USB 2.0 for high speed (HS) operations.

USB 2.0 HS

This port is compliant with the USB 2.0 specifications.

The following table lists the available signals:

PAD

38

36

Signal

USB_D+

USB_D-

I/O

I/O

I/O

Function

USB differential Data (+)

USB differential Data (-)

Type

0.3…2.8V

0.3…2.8V

The USB interface is powered directly from the 3V3 supply.



1vv0301006 Rev.10 – 2015-12-06

8. SIM interface

The SIM pins provide the connections necessary to interface to a SIM socket located on the host device. Voltage levels over this interface comply with 3GPP standards.

SIM Card Interface

8

SIMVCC

10

SIMIO

12

SIMCLK

14

SIMRST

O External SIM signal – Power supply for the SIM 1.8 / 3V

I/O External SIM signal - Data I/O 1.8 / 3V

O

O

External SIM signal – Clock

External SIM signal – Reset

1.8 / 3V

1.8 / 3V

Following picture depicts the external SIM recommended connections:

NOTE:

DO NOT TERMINATE PINS 8, 10, 12, 14 WHEN USING MODEL INCLUDING

SIM CARD HOLDER.



1vv0301006 Rev.10 – 2015-12-06

9. Control signals

The XE910 Mini PCIe provides signals for module control, as described in the following table:

9.1.

Pin Signal

1

WAKE#

20

W_DISABLE#

22

PERST#

42

LED_WWAN#

I

I

I/O Function

O

Type

Active low signal used to wake up the system from stand-by 3.3V

O

Active low signal for wireless disabling (Airplane mode)

Active low functional reset to the card

Active low, open drain signal for WWAN LED driving, used to provide module’s status indication

3.3V

3.3V

3.3V…5V

WAKE#

WAKE# is driven, by default, by the module according the PCI Express Mini Card

Electromechanical Specification Revision 1.2.

NOTE:

WAKE# IS NOT SUPPORTED IN HOST USING PCI EXPRESS MINI CARD

ELECTROMECHANICAL SPECIFICATION REVISION 1.1 AND BELOW.

NOTE:

THIS SIGNAL IS NOT ACTIVE BY DEFAULT. IF DESIRED IT CAN BE

CONFIGURED REMAPPING AN EVENT UNDER MONITORING THROUGH

AT#EVMONI. FOR DETAILS REFER TO THE AT COMMAND USER GUIDE



1vv0301006 Rev.10 – 2015-12-06

Following picture shows the internal WAKE# driver:

WAKE# output may be connected to an edge sensitive application input (e.g. a microcontroller input with IRQ enabled). No external pull-up is needed, since it is internally implemented.

EXAMPLE:

In the following example, a RING monitor activates the WAKEUP signal. (cf.

Event Monitor App.Note 80000nt10043a)

AT#ENAEVMONI=0 //disable all events

AT#GPIO=3,0,1 //Set GPIO3=>’0’, “WAKE signal reset”

AT#ENAEVMONICFG=3,1,2 //AT port setting

AT#EVMONI="RING",0,1,3 //event 0-RING, after 3 rings

AT#EVMONI="RING",0,0,"AT#GPIO=3,1,1" //GPIO3=>’1’, “WAKE signal active”

AT#EVMONI=”RING”,1 //event 0-RING enabled

AT#EVMONI="GPIO1",1,1,3 //event 1-GPIO3

AT#EVMONI="GPIO1",1,2,1 //when goes hi

AT#EVMONI="GPIO1",1,3,5 //after 5s

AT#EVMONI="GPIO1",1,0," AT#GPIO=3,0,1" //Set GPIO3=>’0’, “WAKE signal reset”

AT#EVMONI="GPIO1",1 //event 1-GPIO3 enabled

AT#ENAEVMONI=1 //enable all events


9.2.


1vv0301006 Rev.10 – 2015-12-06

W_DISABLE#

W_DISABLE# is used to force the module to shut down. Thanks to its internal pull-up, leaving this pin unconnected allows the module to operate normally. This switch follows the behavior as described in the PCI-Express Mini Card specification.

LED_WWAN#

LED_WWAN# is driven, by default, by the module according the PCI Express Mini Card

Electromechanical Specification Revision 1.1. If desired, LED behavior can be configured by adjusting software settings. The following picture shows the internal

LED_WWAN# driver and its recommended connection to a LED:

R x

should be dimensioned according to typical voltage drop on application LED and to its supply voltage (3V3 to 5V).

NOTE:

THIS SIGNAL IS NOT ACTIVE BY DEFAULT. REFER TO AT#SLED

DESCRIPTION IN THE AT COMMAND USER GUIDE



1vv0301006 Rev.10 – 2015-12-06

PERST#

Signal

Reset Signal

Function

PERST# * Phone reset

I/O

I

Pin

22

PERST# * is used to reset the xE910

.

Whenever this signal is pulled low, the xE910 is reset. When the device is reset it stops any operation. After the release of the reset the xE910 is unconditionally restarted, without doing any detach operation from the network where it is registered. The reset signal must not be used to normally restart the device, but only as an emergency exit in the rare case the device remains stuck waiting for some network response.

PERST#* is internally controlled on start-up to achieve a proper power-on reset sequence, so there's no need to control this pin on start-up. It may only be used to reset a device already on that is not responding to any command.

NOTE:

Do not use this signal to power cycle the xE910 Mini PCIe. Use the AT#SHDN command instead.

Reset Signal Operating levels

:

Signal Min Max

RESET Input high

RESET Input low

2.0V

-0.5V

3.6V

0.8V

* this signal is not internally pulled up so an external pull-up is required whenever the pin is not used.

If PERST# is used, then it

must always be connected to a push-pull output

in order to allow the internal circuitry to correctly execute power on reset and under voltage lockout functions.

10. Audio Section Overview

The xE910 Module does not provide an Analog Audio section.

One DIGITAL AUDIO bus is available.

In order to develop an application including an Analog Audio it is necessary to add a


10.1.

10.2.

dedicated CODEC on the Application design.


1vv0301006 Rev.10 – 2015-12-06

Electrical Characteristics

The product provides a PCM Digital Audio Interface (DVI) on the following Pins:

Digital Voice Interface (DVI)

45

PCM_CLK

47

PCM_RX

I/O Digital Audio Interface (CLK)

I Digital Audio Interface (RX)

CMOS 1.8V

CMOS 1.8V

49

PCM_TX O Digital Audio Interface (TX) CMOS 1.8V

51

PCM_SYNC I/O Digital Audio Interface (SYNC) CMOS 1.8V

More details on the use of digital audio can be found in Module’s DVI application Note.

NOTE:

THESE SIGNALS ARE 1.8V, NOT COMPATIBLE WITH Mini PCIe BUSES.

THIS IS AN ADVANCED VOICE FUNCTIONALITY AND THE HOST SHOULD TAKE

CARE OF CORRECT COMPATIBILITY.

CODEC Example

Please refer to the Module’s Digital Voice Application Note



1vv0301006 Rev.10 – 2015-12-06

11. Mechanical specifications

The xE910 Mini PCIe adapters have been designed to be compliant with a standard lead-free SMT process.

Moreover, it is compatible with the Mini PCIe card 52-pin card edge-type connector.

The position of the antenna connectors is shown in the following picture.

Soldering pads are present on the back side of the adapter board to allow the optional mounting of a sim-holder. Starting from p/n HEPCxyyy204Tzzz the carrier board has been unified to the same used on the product DE910 Mini PCIe.


11.1.


1vv0301006 Rev.10 – 2015-12-06

The Telit xE910 Mini PCIe adapter overall dimensions are:



Length:



Width:

51.0 mm

30 mm



Thickness: 3.2 mm



Thickness(SIM holder version): 4.78 mm

The module complies with the standard dimensions specified in the

PCI Express

Mini Card Electromechanical Specification Revision 1.1

WEIGHT

The Telit xE910 Mini PCIe adapter weight is about 10 grams.

ENVIRONMENTAL REQUIREMENTS

Temperature range

Storage and operating

Temperature Range

-40° ~ +85° C



1vv0301006 Rev.10 – 2015-12-06

12. Packing system

The XE910 Mini PCIe modules are packaged on trays of

20

pieces each.



1vv0301006 Rev.10 – 2015-12-06

13. SAFETY RECOMMANDATIONS

READ CAREFULLY

Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas:



Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc



Where there is risk of explosion such as gasoline stations, oil refineries, etc

It is rthe esponsibility of the user to enforce the country regulation and the specific environment regulation.

Do not disassemble the product; any mark of tampering will compromise the warranty validity.

We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations.

The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode.

The system integrator is responsible for the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force.

Every module has to be equipped with a proper antenna with specific characteristics.

The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation.

The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information’s are available on the European

Community website: http://ec.europa.eu/enterprise/sectors/rtte/documents/

The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at: http://ec.europa.eu/enterprise/sectors/electrical



1vv0301006 Rev.10 – 2015-12-06

14. Conformity assessment issues

The following chapters are related to the module soldered on the carrier board

14.1. 1999/5/EC Directive (HE910)

The HE910 mPCIe and HE910-D mPCIe have been evaluated against the essential requirements of the 1999/5/EC Directive.

Bulgarian

С настоящето Telit Communications S.p.A. декларира, че 2G/3G module отговаря на съществените изисквания и другите приложими изисквания на Директива 1999/5/ЕС.

Czech Telit Communications S.p.A. tímto prohlašuje, že tento 2G/3G module je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Danish Undertegnede Telit Communications S.p.A. erklærer herved, at følgende udstyr 2G/3G module overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Dutch

English

Hierbij verklaart Telit Communications S.p.A. dat het toestel 2G/3G module in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Hereby, Telit Communications S.p.A., declares that this 2G/3G module is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Estonian Käesolevaga kinnitab Telit Communications S.p.A. seadme 2G/3G module vastavust direktiivi

1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

German Hiermit erklärt Telit Communications S.p.A., dass sich das Gerät 2G/3G module in

Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen

Greek

Bestimmungen der Richtlinie 1999/5/EG befindet.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Telit Communications S.p.A. ΔΗΛΩΝΕΙ ΟΤΙ 2G/3G module

ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ

ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Hungarian Alulírott, Telit Communications S.p.A. nyilatkozom, hogy a 2G/3G module megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Finnish Telit Communications S.p.A. vakuuttaa täten että 2G/3G module tyyppinen laite on direktiivin

1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

French Par la présente Telit Communications S.p.A. déclare que l'appareil 2G/3G module est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Icelandic Hér með lýsir Telit Communications S.p.A. yfir því að 2G/3G module er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC

Italian Con la presente Telit Communications S.p.A. dichiara che questo 2G/3G module è conforme ai

Latvian requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Ar šo Telit Communications S.p.A. deklarē, ka 2G/3G module atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Lithuanian Šiuo Telit Communications S.p.A. deklaruoja, kad šis 2G/3G module atitinka esminius

Maltese reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Hawnhekk, Telit Communications S.p.A., jiddikjara li dan 2G/3G module jikkonforma malħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Norwegian Telit Communications S.p.A. erklærer herved at utstyret 2G/3G module er i samsvar med de

Polish grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

Niniejszym Telit Communications S.p.A. oświadcza, że 2G/3G module jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC



1vv0301006 Rev.10 – 2015-12-06

Portuguese Telit Communications S.p.A. declara que este 2G/3G module está conforme com os requisitos

Slovak essenciais e outras disposições da Directiva 1999/5/CE.

Telit Communications S.p.A. týmto vyhlasuje, že 2G/3G module spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

Slovenian Telit Communications S.p.A. izjavlja, da je ta 2G/3G module v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.

Spanish Por medio de la presente Telit Communications S.p.A. declara que el 2G/3G module cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva

1999/5/CE.

Swedish Härmed intygar Telit Communications S.p.A. att denna 2G/3G module står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv

1999/5/EG.

In order to satisfy the essential requirements of 1999/5/EC Directive, the HE910 mPCIe is compliant to the following standards:

RF spectrum use (R&TTE art. 3.2)

EMC (R&TTE art. 3.1b)

Health & Safety (R&TTE art. 3.1a)

EN 300 440-2 V1.4.1

EN 301 511 V9.0.2

EN 301 908-1 V6.2.1

EN 301 908-2 V6.2.1

EN 301 489-1 V1.9.2

EN 301 489-3 V1.4.1

EN 301 489-7 V1.3.1

EN 301 489-24 V1.5.1

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011

EN 62311:2008

In order to satisfy the essential requirements of 1999/5/EC Directive, the HE910-D mPCIe is compliant to the following standards:

RF spectrum use (R&TTE art. 3.2) EN 301 511 V9.02

EN 301 908-1 V6.2.1

EN 301 908-2 V6.2.1

EMC (R&TTE art. 3.1b) EN 301 489-1 V1.9.2

EN 301 489-7 V1.3.1

EN 301 489-24 V1.5.1

Health & Safety (R&TTE art. 3.1a) EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011

EN 62311:2008

The conformity assessment procedure referred to in Article 10 and detailed in Annex V of Directive

1999/5/EC has been followed with the involvement of the following Notified Body:

CETECOM ICT SERVICES GMBH

Untertürkheimer Straße 6-10 66117

SAARBRÜCKEN

Country: Germany

Notified Body Number 0682

.

Thus, the following marking is included in the product:



The full declaration of conformity can be found on the following address: http://www.telit.com/

1vv0301006 Rev.10 – 2015-12-06

There is no restriction for the commercialisation of the HE910 mPCIe, HE910-D mPCIe in all the countries of the European Union.

Final product integrating this module must be assessed against essential requirements of the 1999/5/EC

(R&TTE) Directive. It should be noted that assessment does not necessarily lead to testing. Telit

Communications S.p.A. recommends carrying out the following assessments:




It will depend on the antenna used on the final product.

Testing

Testing

Alternately, assessment of the final product against EMC (Art. 3.1b) and Electrical safety (Art. 3.1a) essential requirements can be done against the essential requirements of the EMC and the LVD

Directives:

•

Low Voltage Directive 2006/95/EC and product safety

•

Directive EMC 2004/108/EC for conformity for EMC



1vv0301006 Rev.10 – 2015-12-06

14.2. FCC/IC Regulatory notices (HE910)

Modification statement

Telit has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment.

Telit n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature.

Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.

Interference statement

This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Wireless notice

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below:

Frequency band HE910, HE910-D

GSM 850/FDD V

PCS 1900/FDD II

FDD IV

5.22 dBi

3.31 dBi

6.45 dBi

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.



1vv0301006 Rev.10 – 2015-12-06

Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non contrôlé. L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et votre corps. Gain de l'antenne doit être ci-dessous:

Bande de fréquence HE910, HE910-D

GSM 850/FDD V

PCS 1900/FDD II

FDD IV

5.22 dBi

3.31 dBi

6.45 dBi

L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à autre antenne ou autre émetteur.

FCC Class B digital device notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-

Consult the dealer or an experienced radio/TV technician for help.



1vv0301006 Rev.10 – 2015-12-06

14.3. 1999/5/EC Directive (LE910)

The LE910-EUG module has been evaluated against the essential requirements of the 1999/5/EC

Directive.

Bulgarian

С настоящето Telit Communications S.p.A. декларира, че 2G/3G/LTE module отговаря на съществените изисквания и другите приложими изисквания на

Директива 1999/5/ЕС.

Czech Telit Communications S.p.A. tímto prohlašuje, že tento 2G/3G/LTE module je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Danish Undertegnede Telit Communications S.p.A. erklærer herved, at følgende udstyr

2G/3G/LTE module overholder de væsentlige krav og øvrige relevante krav i direktiv

1999/5/EF.

Dutch

English

Hierbij verklaart Telit Communications S.p.A. dat het toestel 2G/3G/LTE module in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Hereby, Telit Communications S.p.A., declares that this 2G/3G/LTE module is in compliance with the essential requirements and other relevant provisions of Directive

1999/5/EC.

Estonian Käesolevaga kinnitab Telit Communications S.p.A. seadme 2G/3G/LTE module vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

German Hiermit erklärt Telit Communications S.p.A., dass sich das Gerät 2G/3G/LTE module in

Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen

Greek

Bestimmungen der Richtlinie 1999/5/EG befindet.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Telit Communications S.p.A. ΔΗΛΩΝΕΙ ΟΤΙ 2G/3G/LTE module

ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ

ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Hungarian Alulírott, Telit Communications S.p.A. nyilatkozom, hogy a 2G/3G/LTE module megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Finnish

French

Telit Communications S.p.A. vakuuttaa täten että 2G/3G/LTE module tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Par la présente Telit Communications S.p.A. déclare que l'appareil 2G/3G/LTE module est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Icelandic Hér með lýsir Telit Communications S.p.A. yfir því að 2G/3G/LTE module er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC

Italian Con la presente Telit Communications S.p.A. dichiara che questo 2G/3G/LTE module è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva

Latvian

1999/5/CE.

Ar šo Telit Communications S.p.A. deklarē, ka 2G/3G/LTE module atbilst Direktīvas

1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Lithuanian Šiuo Telit Communications S.p.A. deklaruoja, kad šis 2G/3G/LTE module atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.



1vv0301006 Rev.10 – 2015-12-06

Maltese Hawnhekk, Telit Communications S.p.A., jiddikjara li dan 2G/3G/LTE module jikkonforma malħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-

Dirrettiva 1999/5/EC.

Norwegian Telit Communications S.p.A. erklærer herved at utstyret 2G/3G/LTE module er i samsvar

Polish med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

Niniejszym Telit Communications S.p.A. oświadcza, że 2G/3G/LTE module jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy

1999/5/EC

Portuguese Telit Communications S.p.A. declara que este 2G/3G/LTE module está conforme com

Slovak os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

Telit Communications S.p.A. týmto vyhlasuje, že 2G/3G/LTE module spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

Slovenian Telit Communications S.p.A. izjavlja, da je ta 2G/3G/LTE module v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.

Spanish Por medio de la presente Telit Communications S.p.A. declara que el 2G/3G/LTE module cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Swedish Härmed intygar Telit Communications S.p.A. att denna 2G/3G/LTE module står I

överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

In order to satisfy the essential requirements of 1999/5/EC Directive, the LE910-EUG module is compliant with the following standards:

RF spectrum use (R&TTE art. 3.2) EN 300 440-2 V1.4.1

EN 301 511 V9.0.2

EN 301 908-1 V6.2.1



EN 301 908-2 V6.2.1

EN 301 908-13 V6.2.1

EN 301 489-1 V1.9.2

EN 301 489-3 V1.4.1

EN 301 489-7 V1.3.1

EN 301 489-24 V1.5.1

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 +

AC:2011

EN 62311:2008

EN 62479:2010

The conformity assessment procedure referred to in Article 10 and detailed in Annex IV of Directive 1999/5/EC has been followed with the involvement of the following Notified Body:

AT4 wireless, S.A.

Parque Tecnologico de Andalucía

C/ Severo Ochoa 2

29590 Campanillas – Málaga

SPAIN

Notified Body No: 1909



1vv0301006 Rev.10 – 2015-12-06

Thus, the following marking is included in the product:

The full declaration of conformity can be found on the following address: http://www.telit.com/

There is no restriction for the commercialisation of the LE910-EUG modules in all the countries of the

European Union.

Final product integrating this module must be assessed against essential requirements of the 1999/5/EC

(R&TTE) Directive. It should be noted that assessment does not necessarily lead to testing. Telit

Communications S.p.A. recommends carrying out the following assessments:




It will depend on the antenna used on the final product.

Testing

Testing

Alternately, assessment of the final product against EMC (Art. 3.1b) and Electrical safety (Art. 3.1a) essential requirements can be done against the essential requirements of the EMC and the LVD

Directives:

•

Low Voltage Directive 2006/95/EC and product safety

•

Directive EMC 2004/108/EC for conformity for EMC



1vv0301006 Rev.10 – 2015-12-06

14.4. FCC/IC Regulatory notices (LE910)



Telit n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.


This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.


Wireless notice

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment.

The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below:

Frequency band LE910-NAG LE910-NVG LE910-SVG

700 MHz

850 MHz

1700 MHz

8.74 dBi

6.93 dBi

5.00 dBi

9.16 dBi

9.42 dBi

5.00 dBi

6.93 dBi

N/A

5.00 dBi

1900 MHz 2.51 dBi 8.01 dBi N/A

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.



1vv0301006 Rev.10 – 2015-12-06


Bande de fréquence LE910-NAG LE910-NVG LE910-SVG

700 MHz

850 MHz

1700 MHz

8.74 dBi

6.93 dBi

5.00 dBi

9.16 dBi

9.42 dBi

5.00 dBi

6.93 dBi

N/A

5.00 dBi

1900 MHz 2.51 dBi 8.01 dBi N/A



This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:


-


-



Labelling Requirements for the Host device

The host device shall be properly labelled to identify the modules within the host device. The certification label of the module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the FCC ID and IC of the module, preceded by the words "Contains transmitter module", or the word "Contains", or similar wording expressing the same meaning, as follows:

LE910-NAG

Contains FCC ID: RI7LE910NA

Contains IC: 5131A-LE910NA

LE910-NVG

Contains FCC ID: RI7LE910NV

Contains IC: 5131A-LE910NV

LE910-SVG

Contains FCC ID: RI7LE910SV

Contains IC: 5131A-LE910SV



1vv0301006 Rev.10 – 2015-12-06

L'appareil hôte doit être étiqueté comme il faut pour permettre l'identification des modules qui s'y trouvent.

L'étiquette de certification du module donné doit être posée sur l'appareil hôte à un endroit bien en vue en tout temps. En l'absence d'étiquette, l'appareil hôte doit porter une étiquette donnant le FCC ID et le IC du module, précédé des mots « Contient un module d'émission », du mot « Contient » ou d'une formulation similaire exprimant le même sens, comme suit :

LE910-NAG

Contains FCC ID: RI7LE910NA

Contains IC: 5131A-LE910NA

LE910-NVG

Contains FCC ID: RI7LE910NV

Contains IC: 5131A-LE910NV

LE910-SVG

Contains FCC ID: RI7LE910SV

Contains IC: 5131A-LE910SV

CAN ICES-3 (B) / NMB-3 (B)

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003.



1vv0301006 Rev.10 – 2015-12-06

Conformity Assessment Issues / Problèmes d'évaluation de conformité (DE910)

The DE910 is FCC/IC Approved as a module to be installed in other devices. This device should be used only for fixed and mobile applications and if the final product after integration is intended for portable use, a new application and FCC is required.

Le DE910 est approuvé FCC/IC comme module à installer dans d'autres dispositifs. Ce dispositif doit être utilisé uniquement pour des applications fixes et mobiles et si le produit fini est prévu après intégration pour un usage portatif, une nouvelle application et la FCC est requise

The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements.

L'utilisateur est averti que ce dispositif doit être utilisé uniquement comme spécifié dans ce manuel pour répondre aux normes d'exposition aux ondes rf.

Use of this device in a manner inconsistent with this manual could lead to excessive

RF exposure conditions.

L'utilisation de ce dispositif en quelque sorte contradictoire avec ce manuel a pu mener aux états excessifs d'exposition de rf.

The DE910 conforms to the following US Directives:

•

Use of RF Spectrum. Standards: FCC47 Part 22&24

•

EMC Standards: FCC47 Part 15

Le DE910 est conforme aux directives suivantes des USA

•

Utilisation de spectre de rf. Normes : FCC47 partie 22&24

•

Normes d'EMC : FCC47 partie 15

This device complies with Part 15 of the FCC Rules.

Ce dispositif est conforme à la partie 15 des règles FCC.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le fonctionnement est sujet aux deux conditions suivantes :

(1) ce dispositif peut ne pas causer l'interférence nocive, et

(2) ce dispositif doit accepter aucune interférence, y compris un interférence qui pourrait causer le fonctionnement non désiré du dispositif.



1vv0301006 Rev.10 – 2015-12-06

The user must refer to below information to meet the FCC/IC's RF exposure rules and regulations when they design:

Lors de la conception, l'utilisateur doit se référer à l'information ci-dessous pour remplir les conditions et règlementations FCC/IC' d’exposition aux ondes RF:

•

The system antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all the persons and must not be colocated or operating in conjunction with any other antenna or transmitter.

Le système d’antenne utilisé pour cet émetteur doit être installé à une distance d’au moins de 20 cm de toute personne et ne doit pas être co-implanté ou opérer en même temps que n'importe quelle autre antenne ou émetteur.

•

The system antenna(s) used for this module must not exceed 5.12dBi in CDMA

BC0 and 6.12dBi in CDMA BC1 for mobile and fixed or mobile operating configurations.

Le système d’ antenne utilisé pour ce module ne doit pas dépasser 5.12dBi en

CDMA BC0 et 6.12dBi en CDMA BC1 pour des configurations mobiles et fixes ou des configurations opérant en mode mobile.

•

Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and to have their complete product tested and approved for FCC compliance.

Les instructions d’installation de l’antenne ainsi que les conditions de fonctionnement de l’émetteur doivent être remis aux utilisateurs et aux installateurs conformément à la règlementation sur l’exposition aux ondes rf.

Des fabricants des dispositifs mobiles, fixes ou portables incorporant ce module sont invités à clarifier toutes les questions de normalisation et à avoir leur produit complètement testé pour la mise en conformité FCC.

•

DE910 is intended for the OEM integrator only.

DE910 est prévu pour l'intégrateur OEM seulement.

•

The user is required to see the Grant of Equipment document for other restrictions.

L'utilisateur doit se referrer au document « Grant of equipment » pour d'autres restrictions.

•

DE910 must be operated and used with a locally approved access point.

DE910 doit être actionné et utilisé avec un point d'accès localement approuvé.

•

The radio transmitter(IC ID: 5131A-DE910DUAL) has been approved by

Industry Canada to operate with the antenna type listed in this manual with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

L'émetteur radio (identification d'IC : 5131A-DE910DUAL) a été approuvé par

Industry Canada pour fonctionner avec le type d'antenne énuméré dans ce manuel avec le gain autorisé maximum et l'impédance d’antenne exigée pour chaque type d'antenne indiqué. Les types d'antenne non inclus dans cette liste,



1vv0301006 Rev.10 – 2015-12-06 ayant un gain supérieur au gain maximum indiqué pour ce type, sont strictement interdits pour un usage avec ce dispositif.

The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations.

•

Host system including DE910 must be labeled with

“Contains transmitter module with

FCC ID: RI7DE910-DUAL and IC ID: 5131A-DE910DUAL”

Les notices de normalisation et de sécurité doivent se trouver dans la documentation fournie à l'utilisateur du produit ou du système incorporant un adaptateur conforme aux règlementations locales.

•

Le système hôte comprenant DE910 doit être marqué avec « Contient un module émetteur avec IDENTIFICATION FCC : RI7DE910-DUAL et identification IC : 5131A-DE910DUAL »

14.6. CONFORMITY ASSESSMENT ISSUES (LE910 V2)

14.6.1. FCC/IC Regulatory notices



Telit n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.


This device complies with Part 15 of the FCC Rules and Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.



1vv0301006 Rev.10 – 2015-12-06


Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non contrôlé. L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et votre corps.

Gain de l'antenne doit être ci-dessous:

RF exposure

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below:

Frequency Band

700 MHz

850 MHz

Antenna Gain

LE910-NA V2 LE910-SV V2

6.63 dBi

6.63 dBi

6.94 dBi

N/A

1700 MHz 6.00 dBi 6.00 dBi

1900 MHz 8.51 dBi 9.01 dBi


Gain de l‘antenne


Bande de fréquence

700 MHz

850 MHz

1700 MHz

1900 MHz

V2


1vv0301006 Rev.10 – 2015-12-06

LE910-NA LE910-SV

V2

6.63 dBi 6.94 dBi

6.63 dBi N/A

6.00 dBi 6.00 dBi

8.51 dBi 9.01 dBi



This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•


•


•


•




1vv0301006 Rev.10 – 2015-12-06

Labelling Requirements for the Host device

The host device shall be properly labelled to identify the modules within the host device. The certification label of the module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the

FCC ID and IC of the module, preceded by the words "Contains transmitter module", or the word "Contains", or similar wording expressing the same meaning, as follows:

LE910-NA V2

Contains FCC ID: RI7LE910NAV2

Contains IC: 5131A-LE910NAV2

LE910-SV V2

Contains FCC ID: RI7LE910SVV2

Contains IC: 5131A-LE910SVV2

L'appareil hôte doit être étiqueté comme il faut pour permettre l'identification des modules qui s'y trouvent. L'étiquette de certification du module donné doit être posée sur l'appareil hôte à un endroit bien en vue en tout temps. En l'absence d'étiquette, l'appareil hôte doit porter une étiquette donnant le FCC ID et le IC du module, précédé des mots « Contient un module d'émission », du mot « Contient » ou d'une formulation similaire exprimant le même sens, comme suit :

LE910-NA V2

Contains FCC ID: RI7LE910NAV2

Contains IC: 5131A-LE910NAV2

LE910-SV V2

Contains FCC ID: RI7LE910SVV2

Contains IC: 5131A-LE910SVV2

CAN ICES-3 (B) / NMB-3 (B)

This Class B digital apparatus complies with Canadian ICES-003.



1vv0301006 Rev.10 – 2015-12-06

Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003.

14.7. Safety Recommendations (LE910 V2)


• Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc.

• Where there is risk of explosion such as gasoline stations, oil refineries, etc.

It is responsibility of the user to enforce the country regulation and the specific environment regulation.

Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode.

The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation.



1vv0301006 Rev.10 – 2015-12-06

The European Community provides some Directives for the electronic equipment introduced on the market. All the relevant information’s are available on the

European Community website: http://ec.europa.eu/enterprise/sectors/rtte/documents/

The text of the Directive 99/05 regarding telecommunication equipment is available, while the applicable Directives (Low Voltage and EMC) are available at: http://ec.europa.eu/enterprise/sectors/electrical/

14.8.

14.9.

Safety Recommendations (HE910)

The device must be supplied with a limited power source that meets clause 2.5 of the EN 60950-1 standard. This requirements are:

For power supplies without overcurrent protection device----> Shortcircuit current < 8

A. / Apparent power < 100 VA

For power supplies with overcurrent protection device (rated current of overcurrent device shall be < 5A) --- > Shortcircuit current < 333 A. / Apparent power < 250 VA.

Furthermore, the device must be installed within an enclosure that meets HB class or pass the 550º glowing fire test of EN 60695-2-11.

Safety Recommendations (DE910)

READ CAREFULLY


•

Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc.

•

Where there is risk of explosion such as gasoline stations, oil refineries, etc.

It is the responsibility of the user to enforce the country’s regulations and the specific environmental regulation.

Do not disassemble the product; any evidence of tampering will compromise the warranty validity. Follow the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to conform to the security and fire prevention regulations. The



1vv0301006 Rev.10 – 2015-12-06 product has to be handled with care, avoiding any contact with the pads because electrostatic discharges may damage the product itself.

The system integrator is responsible for the functioning of the final product; therefore, care has to be taken with the external components of the module as well as of any project or installation issue because of the risk of disturbing the CDMA network or external devices or having impact on security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case this requirement cannot be satisfied, the system integrator has to assess the final product against SAR regulations.

15. Document History

Revision Date Changes

ISSUE#0 2012-05-08 First issue

ISSUE#1 2012-27-07 3.1 PINOUT updated

9 Wake functionality and new example

10 Audio section added

11 Mechanical layout drawing changed

ISSUE#2 2012-25-09 Minor grammatical corrections

ISSUE#3 2012-11-22 Minor grammatical corrections.

4.2 peak current requirement raised to 2.4A

5 sensitivity and output power (modify)

8 SH note added. Capacitor on SIMVCC changed from 1uF to 100 nF.

11 new drawing

Added chapters 5.3.1, 5.3.2, 11.1, 11.2

ISSUE#4 2013-08-22 Temperature Range modified

ISSUE#5 2014-04-08 Updated chapter 11.2

ISSUE#6 2014-05-16 Updated chapter 11

ISSUE #7 2014-08-06 Added LE910 and DE910

Updated document’s tables

ISSUE #8 2014-10-20 Chapter 5.5.2 updated

ISSUE#9 2015-02-03 Chapter 14 updated; added 14.6 Safety

Recommendations on HE910

ISSUE#10 2015-06-12 Added LE910 V2 across the document


xE910 Mini PCIe Hardware User Guide

xE910 Mini PCIe Hardware User Guide

APPLICABILITY TABLE

Contents

1. Introduction

2. Overview

3. xE910 Mini PCI express card connections

4. Power Supply

5. GSM/WCDMA/LTE /CDMA Radio Section

5.3.1.

GSM/WCDMA/LTE/CDMA Antenna - Installation Guidelines

5.5.1. GNSS Performances

5.5.2.

GNSS RF Front End Design

6. Logic level specifications

7. USB Port

8. SIM interface

9. Control signals

10. Audio Section Overview

11. Mechanical specifications

12. Packing system

13. SAFETY RECOMMANDATIONS

14. Conformity assessment issues

14.6.1. FCC/IC Regulatory notices

Gain de l‘antenne

Bande de fréquence

V2

LE910-NA LE910-SV

V2

15. Document History

Related manuals

Table of contents

Languages

xE910 Mini PCIe Hardware User Guide

xE910 Mini PCIe Hardware User Guide

APPLICABILITY TABLE

Contents

1. Introduction

2. Overview

3. xE910 Mini PCI express card connections

4. Power Supply

5. GSM/WCDMA/LTE /CDMA Radio Section

5.3.1.

GSM/WCDMA/LTE/CDMA Antenna - Installation Guidelines

5.5.1. GNSS Performances

5.5.2.

GNSS RF Front End Design

6. Logic level specifications

7. USB Port

8. SIM interface

9. Control signals

10. Audio Section Overview

11. Mechanical specifications

12. Packing system

13. SAFETY RECOMMANDATIONS

14. Conformity assessment issues

14.6.1. FCC/IC Regulatory notices

Gain de l‘antenne

Bande de fréquence

V2

LE910-NA LE910-SV

V2

15. Document History

Related manuals

Telit Wireless Solutions

DE910-DUAL

Telit Communications S.p.A.

RI7LE910SVL

Telit Communications S.p.A.

RI7LE910SVV2

Telit Wireless Solutions

EVK4-LE910-EU1 Series

Telit Wireless Solutions

LE910Cx

Table of contents

Languages