Advertisement
Advertisement
INSTALLATION INSTRUCTIONS
FTS24211
1 FT50660
1 FT50661
1 FT50662
1 FT50685
2018 JEEP JL INTERIOR CARGO RACK
CARGO TRAY (CENTER)
CARGO TRAY SIDE (DRIVER)
CARGO TRAY SIDE (PASSENGER)
HARDWARE SUBASSEMBLY
FT50685
1 FT24211i
1 FT50659
1 FT50697
1 FTAS12
1 FTREGCARD
HARDWARE SUBASSEMBLY
INSTRUCTIONS
HARDWARE KIT
EDGE TRIM 120”
STICKER FT BLUE
REGISTRATION CARD
FT50659 - HARDWARE KIT
6 3/8-16 X 1” BUTTON HEAD BOLT
12 3/8” SAE WASHER
6 3/8-16 NYLOCK NUT
LOCATION
2018-19 JEEP WRANGLER (JL) 4DR
(HARD TOP ONLY)
INTERIOR CARGO RACK
FTS24211
NOTE: TO ORDER WEARABLE REPLACEMENT COMPONENTS DO NOT USE PART NUMBERS SHOWN ON THIS
INSTRUCTION SHEET. GO TO FABTECH WEBSITE AND LOOK UP WEARABLE REPLACEMENT PARTS TO FIND THE PROPER
PART NUMBER TO ORDER.
Fabtech Motorsports | 4331 Eucalyptus Ave. Chino, CA 91710
Tech Line: 909-597-7800 | Fax: 909-597-7185 | Web: www.fabtechmotorsports.com
- TOOL LIST -
Required Tools (Not Included)
- Basic Hand Tools
- Assorted Metric and S.A.E sockets, and Allen wrenches
- Torque Wrench
- 7/32” Hex Tool
- 9/16” socket or wrench
- T-50 Torx Bit
- PRE-INSTALLATION NOTES -
For technical assistance call:
909-597-7800
or e-mail:
READ THIS BEFORE YOU BEGIN INSTALLATION -
Check all parts to the parts list above before beginning installation. If any parts are missing contact Fabtech at 909-597-7800 and a replacement part will be sent to you immediately.
Read all instructions thoroughly from start to finish before beginning the installation.
Check your local city and state laws prior to the installation of this system for legality. Do not install if not legal in your area.
FOOTNOTES -
- Fits 4-door models only
- Designed for hard top models. Rack does not allow soft top models to fully retract.
2 of 5
- INSTRUCTIONS -
1. Before you begin the install, layout all of the parts and hardware. Next, locate the FT50660 (Center Tray) and install the FT50697 (Edge Trim) around the top edge.
SEE
FIGURE 1
4. Driver side: Install FT50661 (Driver side tray) like shown in FIGURE 4-5 using the factory bolts removed in step 3.
Leave loose.
FIGURE 1 - STEP 1
2. Open the rear gate and window on your Jeep. SEE
FIGURE 2
FIGURE 4 - STEP 4
FIGURE 2 - STEP 2
3. Using T-50 Torx bit, remove and save the two rear bolts that secure the side hard top panels to the body on both driver & passenger sides. SEE FIGURE 3
FIGURE 5 - STEP 4
FIGURE 3 - STEP 3
REMOVE
3 of 5
5. Passenger side: Install FT50662 (Passenger side tray) like shown in FIGURE 6-7 using the factory bolts removed in step 3. Leave Loose
FIGURE 6 - STEP 5
FIGURE 7 - STEP 5
6. Install FT50660 (Center Tray) using the supplied 3/8” hardware. Torque to 44 ft-lbs. SEE FIGURES 8-9
3/8” HARDWARE
FIGURE 8 - STEP 6
4 of 5
FIGURE 9 - STEP 6
7. Torque the factory side panel T-50 bolts to27 ft-lbs.
8. Install Driver Warning Decal. Complete product registration card and mail to Fabtech in order to receive future safety and technical bulletins on this suspension.
For technical assistance call:
909-597-7800
- Product Warranty and Warnings -
Fabtech provides a Limited Lifetime Warranty to the original retail purchaser who owns the vehicle, on which the product was originally installed, for defects in workmanship and materials.
The Limited Lifetime Warranty excludes the following Fabtech items; bushings, bump stops, ball joints, tie rod ends, limiting straps, cross shafts, heim joints and driveshafts. These parts are subject to wear and are not considered defective when worn.
They are warranted for 60 days from the date of purchase for defects in workmanship.
Dirt Logic and Performance Coilover take apart shocks are considered a serviceable shock with a one year warranty on leakage only. Service seal kits are available separately for future maintenance. All other shocks are covered under our Limited Lifetime
Warranty.
Fabtech does not warrant any product for finish, alterations, modifications and/or installation contrary to Fabtech’s instructions.
Alterations to the finish of the parts including but not limited to painting, powder coating, plating and/or welding will void all warranties. Some finish damage may occur to parts during shipping, which is considered normal and is not covered under warranty.
Fabtech products are not designed nor intended to be installed on vehicles used in race applications or for racing purposes or for similar activities. (A “RACE” is defined as any contest between two or more vehicles, or any contest of one or more vehicle against the clock, whether or not such contest is for a prize). This warranty does not include coverage for police or taxi vehicles, race vehicles, or vehicles used for government or commercial purposes. Also excluded from this warranty are sales outside of the United States of America.
Installation of most suspension products will raise the center of gravity of the vehicle and will cause the vehicle to handle differently than stock. It may increase the vehicle’s susceptibility to a rollover, on road and off road, at all speeds. Extreme care should be taken to operate the vehicle safely at all times to prevent rollover or loss of control resulting in serious injury or death.
Fabtech front end Desert Guards may impair the deployment or operation of vehicles equipped with supplemental restraining systems/air bag systems and should not be installed if the vehicle is equipped as so.
Fabtech makes every effort to ensure suspension product compatibility with all vehicles listed on the website, but due to unknown auto manufacturer’s production changes and/or inconstancies by the auto manufacturer, Fabtech cannot be responsible for 100% compatibility, including the fitment of tire and wheel sizes listed. The Tire and Wheel sizes listed in
Fabtech’s website are only a guideline for street driving with noted fender trimming. Fabtech is not responsible for damages to the vehicle’s body or tires. Fabtech is not responsible for premature wear of factory components due to the installation of oversized tires and wheels.
Fabtech’s obligation under this warranty is limited to the repair or replacement, at Fabtech option, of the defective product only.
All costs of removal, installation or re-installation, freight charges, incidental or consequential damages are expressly excluded from this warranty. Fabtech is not responsible for damages and/or warranty of other vehicle parts related or non related to the installed Fabtech product. This warranty is expressly in lieu of all other warranties expressed or implied. This warranty shall not apply to any product that has been subject to accident, negligence, alteration, abuse or misuse as determined by Fabtech.
Fabtech suspension components must be installed as a complete system including shocks as shown on our website. All warranties will become void if Fabtech parts are combined and/or substituted with other aftermarket suspension products.
Combination and/or substitution of other aftermarket suspension parts may cause premature wear and/or product failure resulting in an accident causing injury or death. Fabtech does not warrant products not manufactured by Fabtech.
Depending on the condition of the factory suspension components retained after the installation of a Fabtech suspension not all vehicles may have the same ride stance front to rear as described in the website. The blue color of suspension components shown in all Fabtech photographs are for display purposes only. Majority of all Fabtech components will be black specifically where noted with part numbers ending in BK.
Installation of Fabtech product may void the vehicles factory warranty; it is the consumer’s responsibility to check with their local vehicle’s dealer for warranty disposition before the installation of the product. Some state laws may prohibit modification of suspension to a vehicle in whole or in part. It is the responsibility of the installer and consumer to consult local laws prior to the installation of any Fabtech suspension product to comply with such written laws.
It is the responsibility of the distributor and/or the retailer to review all warranties and warnings of Fabtech products with the consumer prior to purchase.
Fabtech reserves the right to super cede, discontinue, change the design, finish, part number and/or application of parts when deemed necessary without written notice. Fabtech is not responsible for misprints or typographical errors within the website or price sheet. For the most recent Product Warranty and Warnings visit our website www.fabtechmotorsports.com
Instruction Sheet Part# FT24211i 04/08/19
5 of 5

Public link updated
The public link to your chat has been updated.
Advertisement