Cisco Aironet 1000 Series Specifications

Cisco Aironet 1000 Series Specifications
AP1020/1030 Cisco Aironet 1000 Series
IEEE 802.11a/b/g Lightweight Access
Points with External Antennas - Quick
Start Guide
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Text Part Number: 78-17147-01
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and
iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco
Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation,
Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ
Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing,
ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, TeleRouter, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered
trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0502R)
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
© 2005 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
v
Organization
v
Conventions
v
Obtaining Documentation vi
Cisco.com vi
Documentation DVD vi
Ordering Documentation vii
Documentation Feedback vii
Cisco Product Security Overview vii
Reporting Security Problems in Cisco Products
Obtaining Technical Assistance viii
Cisco Technical Support Website viii
Submitting a Service Request ix
Definitions of Service Request Severity
ix
Obtaining Additional Publications and Information
Installation and Configuration
ATTENTION! 2
viii
x
1
Collecting Required Tools and Supplies
4
Pre-Installation Configuration 5
Preparing a Version 3.0 Cisco Aironet 1000 Series Lightweight Access Point 5
Alternate Method of Preparing a Version 3.0 Cisco Aironet 1000 Series Lightweight Access Point
Preparing Mounting Locations
12
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
Ceiling Mount Base 14
Ceiling-Mount Clips 16
Projection Wall Mount 18
Flush Wall Mount 20
Returning MAC Information
APPENDIX
A
Planning Notes A-1
About Cables A-1
About External Antennas
About Mounting Options
14
22
A-2
A-3
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
iii
8
Contents
About Mounting Options A-3
About Physical Security A-4
FCC Statements for Cisco Aironet 1000 Series Lightweight Access Points A-4
EU Regulatory Information A-5
Industry Canada Required User Information for Cisco Aironet 1000 Series Lightweight Access
Points A-6
Safety Considerations A-6
INDEX
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
iv
78-17147-01
Preface
This Guide contains several sections which will help you to install AP1020 and AP1030 Cisco Aironet
1000 Series IEEE 802.11a/b/g lightweight access points. These models contain internal 802.11a and
802.11b/g antennas and connectors for optional external 802.11a and 802.11b/g antennas.
When you are installing AP1010 internal-antenna Cisco Aironet 1000 Series 802.11a/b/g lightweight
access points with internal 802.11a and 802.11b/g antennas and no connectors for optional external
802.11a and 802.11b/g antennas, please refer to the AP1010 Cisco Aironet 1000 Series IEEE
802.11a/b/g Lightweight Access Point Installation and Configuration Guide.
Organization
This guide is organized into the following sections:
•
Installation and Configuration
•
Collecting Required Tools and Supplies
•
Pre-Installation Configuration
•
Preparing Mounting Locations
•
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
•
Returning MAC Information
Conventions
This publication uses these conventions to convey instructions and information:
Command descriptions use these conventions:
•
Commands and keywords are in boldface text.
•
Arguments for which you supply values are in italic.
•
Square brackets ([ ]) mean optional elements.
•
Braces ({ }) group required choices, and vertical bars ( | ) separate the alternative elements.
•
Braces and vertical bars within square brackets ([{ | }]) mean a required choice within an optional
element.
Interactive examples use these conventions:
•
Terminal sessions and system displays are in screen font.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
v
Preface
Obtaining Documentation
•
Information you enter is in boldface screen font.
•
Nonprinting characters, such as passwords or tabs, are in angle brackets (< >).
Notes, cautions, and timesavers use these conventions and symbols:
Tip
Means the following will help you solve a problem. The tips information might not be troubleshooting
or even an action, but could be useful information.
Note
Means reader take note. Notes contain helpful suggestions or references to materials not contained in
this manual.
Caution
Means reader be careful. In this situation, you might do something that could result equipment damage
or loss of data.
Warning
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents.
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
http://www.cisco.com
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Documentation DVD
Cisco documentation and additional literature are available in a Documentation DVD package, which
may have shipped with your product. The Documentation DVD is updated regularly and may be more
current than printed documentation. The Documentation DVD package is available as a single unit.
Registered Cisco.com users (Cisco direct customers) can order a Cisco Documentation DVD (product
number DOC-DOCDVD=) from the Ordering tool or Cisco Marketplace.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
vi
78-17147-01
Preface
Obtaining Documentation
Cisco Ordering tool:
http://www.cisco.com/en/US/partner/ordering/
Cisco Marketplace:
http://www.cisco.com/go/marketplace/
Ordering Documentation
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
•
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from
the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/
•
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 1 800 553-NETS (6387).
Documentation Feedback
You can send comments about technical documentation to [email protected]
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Cisco Product Security Overview
Cisco Product Security Overview
Cisco provides a free online Security Vulnerability Policy portal at this URL:
http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
•
From this site, you can perform these tasks:
•
Report security vulnerabilities in Cisco products.
•
Obtain assistance with security incidents that involve Cisco products.
•
Register to receive security information from Cisco.
A current list of security advisories and notices for Cisco products is available at this URL:
http://www.cisco.com/go/psirt
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
vii
Preface
Obtaining Technical Assistance
If you prefer to see advisories and notices as they are updated in real time, you can access a Product
Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Reporting Security Problems in Cisco Products
Reporting Security Problems in Cisco Products
Cisco is committed to delivering secure products. We test our products internally before we release them,
and we strive to correct all vulnerabilities quickly. If you think that you might have identified a
vulnerability in a Cisco product, contact PSIRT:
Tip
•
Emergencies — [email protected]
•
Nonemergencies — [email protected]
We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive
information that you send to Cisco. PSIRT can work from encrypted information that is compatible with
PGP versions 2.x through 8.x.
Never use a revoked or an expired encryption key. The correct public key to use in your correspondence
with PSIRT is the one that has the most recent creation date in this public key server list:
http://pgp.mit.edu:11371/pks/lookup?search=psirt%40cisco.com&op=index&exact=on
In an emergency, you can also reach PSIRT by telephone:
•
1 877 228-7302
•
1 408 525-6532
Obtaining Technical Assistance
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco
Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical
Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical
Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service
contract, contact your reseller.
Cisco Technical Support Website
The Cisco Technical Support Website provides online documents and tools for troubleshooting and
resolving technical issues with Cisco products and technologies. The website is available 24 hours a day,
365 days a year, at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password.
If you have a valid service contract but do not have a user ID or password, you can register at this URL:
http://tools.cisco.com/RPF/register/register.do
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
viii
78-17147-01
Preface
Obtaining Technical Assistance
Note
Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web
or phone request for service. You can access the CPI tool from the Cisco Technical Support Website by
clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product Identification
Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under
Alerts & RMAs. The CPI tool offers three search options: by product ID or model name; by tree view; or for
certain products, by copying and pasting show command output. Search results show an illustration of your
product with the serial number label location highlighted. Locate the serial number label on your product and
record the information before placing a service call.
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3
and S4 service requests are those in which your network is minimally impaired or for which you require
product information.) After you describe your situation, the TAC Service Request Tool provides
recommended solutions. If your issue is not resolved using the recommended resources, your service
request is assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone.
(S1 or S2 service requests are those in which your production network is down or severely degraded.)
Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business
operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity
definitions.
•
Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations.
You and Cisco will commit all necessary resources around the clock to resolve the situation.
•
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of
your business operation are negatively affected by inadequate performance of Cisco products. You
and Cisco will commit full-time resources during normal business hours to resolve the situation.
•
Severity 3 (S3)—Operational performance of your network is impaired, but most business
operations remain functional. You and Cisco will commit resources during normal business hours
to restore service to satisfactory levels.
•
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation,
or configuration. There is little or no effect on your business operations.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
ix
Preface
Obtaining Additional Publications and Information
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
•
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit
Cisco Marketplace, the company store, at this URL:
http://www.cisco.com/go/marketplace/
•
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press at this URL:
http://www.ciscopress.com
•
Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and
networking investments. Each quarter, Packet delivers coverage of the latest industry trends,
technology breakthroughs, and Cisco products and solutions, as well as network deployment and
troubleshooting tips, configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access Packet magazine at
this URL:
http://www.cisco.com/packet
•
iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies
learn how they can use technology to increase revenue, streamline their business, and expand
services. The publication identifies the challenges facing these companies and the technologies to
help solve them, using real-world case studies and business strategies to help readers make sound
technology investment decisions. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
•
World-class networking training is available from Cisco. You can view current offerings at
this URL:
http://www.cisco.com/en/US/learning/index.html
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
x
78-17147-01
Installation and Configuration
This guide provides you with the information needed to mount AP1020 and AP1030 Cisco Aironet 1000
Series 802.11a/b/g lightweight access points. Cisco Aironet 1000 Series 802.11a/b/g lightweight access
points are part of the innovative Cisco Wireless LAN Solution (Cisco WLAN Solution), and require no
manual configuration after they are mounted.
This document is written assuming that you have already performed a site survey as described in the
Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Point Deployment Guide, that Cisco
Aironet 1000 Series lightweight access point locations and mounting options have been selected, and
that you have one Cisco Aironet 1000 Series lightweight access point per indicated location.
After the site survey is done, you should have a map indicating the following:
Caution
•
Cisco Aironet 1000 Series lightweight access point locations.
•
Cisco Aironet 1000 Series lightweight access point mounting options: hanging from a ceiling, in the
ceiling plenum, projecting away from the wall, flat against the wall, or using the Ceiling-Mount
Bezel Kit.
•
Cisco Aironet 1000 Series lightweight access point power options: power supplied by the AC-to-DC
power supply orderable from the factory, or PoE from a network device or a PoE injector/hub
(usually located in a wiring closet).
Plenum-mounted Cisco Aironet 1000 Series 802.11a/b/g lightweight access points MUST BE powered
using PoE to comply with safety regulations.
If you do not have a map, make one so you can record the MAC addresses from each location and return
them to the person who is planning or managing this wireless network.
Refer to the following sections to install the Cisco Aironet 1000 Series 802.11a/b/g lightweight access
points.
Note
When mounting Cisco Aironet 1000 Series 802.11a/b/g lightweight access points, be sure to maintain a
20 cm (8 in.) separation between the Cisco Aironet 1000 Series 802.11a/b/g lightweight access points
and bystanders to comply with FCC RF exposure regulations. Refer to the “FCC Statements for Cisco
Aironet 1000 Series Lightweight Access Points” section for more information.
For more details about Cisco Aironet 1000 Series lightweight access point installations, refer to the
“Planning Notes” section at the end of this document.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
1
Installation and Configuration
ATTENTION!
While Cisco Aironet 1000 Series IEEE 802.11a/b/g lightweight access points have been engineered for
easy installation, there are some very important guidelines for installation:
•
PLACE Cisco Aironet 1000 Series Lightweight Access Points NO MORE THAN 140 FEET APART
FROM EACH OTHER. Placing Cisco Aironet 1000 Series 802.11a/b/g lightweight access points
farther apart almost always results in poor coverage.
•
DO NOT MOUNT Cisco Aironet 1000 Series Lightweight Access Points OUTSIDE BUILDINGS.
•
DO NOT MOUNT Cisco Aironet 1000 Series Lightweight Access Points ON BUILDING
PERIMETER WALLS UNLESS THE OPERATOR WANTS TO PROVIDE COVERAGE OUTSIDE
THE BUILDING.
•
BE SURE that plenum-mounted Cisco Aironet 1000 Series 802.11a/b/g lightweight access points
are powered using Power over Ethernet (PoE) and use only the metal brackets (not the
Ceiling-Mount Base or the Hanging-Ceiling Clips) to comply with safety regulations.
•
BE SURE THAT Cisco Aironet 1000 Series Lightweight Access Points ARE INSTALLED
VERTICALLY as shown in Figure 1. Installing Cisco Aironet 1000 Series 802.11a/b/g lightweight
access points vertically either standing up in a plenum or hanging from a ceiling, creates the largest
coverage area per Cisco Aironet 1000 Series lightweight access point. Hanging Cisco Aironet 1000
Series 802.11a/b/g lightweight access points from the ceiling provides the best RF coverage.
Access Point Installed Vertically
135662
Figure 1
•
DO NOT MOUNT Cisco Aironet 1000 Series lightweight access point ANTENNAS WITHIN ONE
METER (3 FT.) OF ANY METAL OBSTRUCTIONS. THE RF WAVES FROM Cisco Aironet 1000
Series Lightweight Access Points ARE BLOCKED AND/OR REFLECTED BY METAL OBJECTS
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
2
Installation and Configuration
such as metal HVAC ducts, conduit, pipes, bookcases, elevator shafts, stairwells, and metal walls.
REFER TO THE Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Point
Deployment Guide BEFORE MOUNTING Cisco Aironet 1000 Series Lightweight Access Points
NEAR METAL OBSTRUCTIONS.
Figure 2
Access Point Clearance
135659
1 meter (3 ft.)
clearance
•
WHEN MOUNTING Cisco Aironet 1000 Series Lightweight Access Points IN THE CORNER OF
A RIGHT-ANGLE HALLWAY INTERSECTION, MOUNT THE Cisco Aironet 1000 Series
Lightweight Access Point AT A 45-DEGREE ANGLE TO THE TWO HALLWAYS. The Cisco
Aironet 1000 Series lightweight access point internal antennas are not omnidirectional and cover a
larger area when mounted this way.
Mounting the Access Point in the Correct Direction
135660
Figure 3
When a Cisco Aironet 1000 Series lightweight access point is configured with an IP address and is
moved to a different IP segment, it attempts to join a Cisco Wireless LAN Controller. If it is unable to
join a Cisco Wireless LAN Controller after a number of attempts, it does an arp for the default configured
gateway. If the Cisco Aironet 1000 Series lightweight access point is on the wrong subnet, it will not be
able to resolve the gateway arp and it will attempt to contact a DHCP server. This is the Cisco Aironet
1000 Series lightweight access point IP address fallback feature. However, if the destination IP segment
does not have a DHCP server, the Cisco Aironet 1000 Series lightweight access point retains its original
IP address and can never join the network.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
3
Installation and Configuration
Collecting Required Tools and Supplies
Collecting Required Tools and Supplies
This section describes the tools and information that you should have before installing the access point.
•
One Cisco Aironet 1000 Series lightweight access point per location.
•
Cisco Aironet 1000 Series lightweight access point Mounting Kits, factory-supplied with each Cisco
Aironet 1000 Series lightweight access point.
•
Optional Cisco Aironet 1000 Series lightweight access point Mounting Kits, factory-orderable.
•
Optional AC-to-DC external power supplies, factory-orderable. Note that this option requires the
power cable to be run through the plenum in a metal conduit to meet safety requirements.
•
Map showing Cisco Aironet 1000 Series lightweight access point locations and mounting and power
options.
•
Screwdrivers, drills, and ladder.
•
An assortment of sheet metal and drywall screws and toggle bolts.
•
CAT-5 (or higher) cables to connect the Cisco Aironet 1000 Series lightweight access point locations
and other network devices.
•
Optional Kensington MicroSaver Security Cable to secure each Cisco Aironet 1000 Series
lightweight access point.
Continue with “Pre-Installation Configuration.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
4
Installation and Configuration
Pre-Installation Configuration
Pre-Installation Configuration
The following procedures are designed to ensure that your Cisco Aironet 1000 Series lightweight access
point physical installation and that initial operation goes as expected. If you are unable to prepare your
Cisco Aironet 1000 Series lightweight access point for deployment, this step also describes RMA
(Return Material Authorization) procedures.
Perform the following procedure on each Cisco Aironet 1000 Series lightweight access point BEFORE
deploying it in its final location.
•
Preparing a Version 3.0 Cisco Aironet 1000 Series Lightweight Access Point OR
•
Alternate Method of Preparing a Version 3.0 Cisco Aironet 1000 Series Lightweight Access Point
for installation in a Version 3.0 deployment
If you are unable to perform the following procedure, refer to the “Obtaining Technical Assistance”
section.
Preparing a Version 3.0 Cisco Aironet 1000 Series Lightweight Access Point
If your Cisco Aironet 1000 Series lightweight access point has Operating System 3.0 or a later version
loaded on it, continue with this procedure.
Note
This procedure is written assuming that you are preparing a version 3.0 Cisco Aironet 1000 Series
lightweight access point to operate with a Cisco Wireless LAN Controller.
Configuration Setup
Figure 4
Configuration Setup
Appliance
Switch
Layer 2/3
devices
135675
APs and REAPs
Appliance mode
Direct-connect
mode
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
5
Installation and Configuration
Pre-Installation Configuration
Does My Cisco Aironet 1000 Series Lightweight Access Point Qualify for this Procedure?
Does My Cisco Aironet 1000 Series Lightweight Access Point Qualify for this Procedure?
If your 3.0 or later version Cisco Aironet 1000 Series lightweight access point(s) cannot be configured
for any reason using the following procedure, refer to the “Obtaining Technical Assistance” section.
Configuration Steps for a Cisco Aironet 1000 Series Lightweight Access Point
To configure an access point, perform these steps:
Step 1
Note
Configure the Cisco Wireless LAN Controller in LWAPP Layer 3 Mode and be sure its DS Port is
connected to the network.
When you are installing a Cisco 1030 remote edge lightweight access point, a DHCP server must be
accessible by the access point.
a.
Be sure Cisco Aironet 1000 Series lightweight access point ports are available through the Cisco
Wireless LAN Controller Management/AP-Manager Interface.
b.
Set the Cisco Wireless LAN Controller as the Master so that new Cisco Aironet 1000 Series
802.11a/b/g lightweight access points always associate with it. Use the CLI command show network
config to determine if the Cisco Wireless LAN Controller DS Port is the Master. If the Cisco
Wireless LAN Controller DS Port is not, make it the Master using the CLI command config network
master-base disable.
Step 2
Take the Cisco Aironet 1000 Series lightweight access point out of the box and plug it into the same
subnet as the Cisco Wireless LAN Controller.
Step 3
Apply power to the Cisco Aironet 1000 Series lightweight access point.
a.
Note
Use 802.3af-compatible PoE from the Cisco Wireless LAN Controller or from an orderable inline
power injector. If you do not have PoE available, use an orderable external AC-to-48 VDC Power
Supply plugged into the side of the Cisco Aironet 1000 Series lightweight access point.
Cisco Aironet 1000 Series 802.11a/b/g lightweight access points support 802.3af Power over Ethernet
(PoE). These access points do not support Cisco prestandard PoE. Please use Cisco 802.3af capable PoE
switches or power injectors.
b.
After you power up the Cisco Aironet 1000 Series lightweight access point, the RED Alarm LED
comes on for about 15-20 seconds and then all the LEDs blink sequentially back and forth,
indicating that the Cisco Aironet 1000 Series lightweight access point is trying to find a Cisco
Wireless LAN Controller to associate with. This can continue for up to five minutes. If the Cisco
Aironet 1000 Series lightweight access point remains in this mode for more than five minutes, the
Cisco Aironet 1000 Series lightweight access point is unable to find the Master Cisco Wireless LAN
Controller. Check the connection between the Cisco Aironet 1000 Series lightweight access point
and the Cisco Wireless LAN Controller and be sure the Cisco Aironet 1000 Series lightweight
access point and the Cisco Wireless LAN Controller are on the same subnet.
c.
If the power light does not come on, check the power (it can be powered either with PoE or from an
orderable Cisco Aironet 1000 Series lightweight access point External Power Supply.
d.
Be sure that a DHCP server is configured in the Cisco Wireless LAN Controller for both the
Management Interface and AP-Manager Interface using the CLI, Web User Interface, or Cisco WCS
interface, and that the DHCP server is operating correctly.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
6
Installation and Configuration
Pre-Installation Configuration
e.
After the Cisco Aironet 1000 Series lightweight access point finds the Cisco Wireless LAN
Controller, it attempts to download the new Operating System code if the Cisco Aironet 1000 Series
lightweight access point code version differs from the Cisco Wireless LAN Controller code version.
While this is happening, the LEDs on the top of the Cisco Aironet 1000 Series lightweight access
point blink simultaneously.
Step 4
After the Operating System code download is successful, the Cisco Aironet 1000 Series lightweight
access point reboots. The GREEN LED turns on and the two YELLOW LEDs indicate the states of the
802.11a and 802.11b/g networks. If any part of the network is disabled in the Cisco Wireless LAN
Controller, the corresponding YELLOW LED remains off.
Note
The Red LED can light for about 10-20 seconds when the Cisco Aironet 1000 Series lightweight access
point reboots. If the RED LED comes on AND STAYS ON for more than a minute, disconnect the Cisco
Aironet 1000 Series lightweight access point and call Cisco Technical Assistance Center (TAC).
•
Use the CLI command show ap summary. If the new Cisco Aironet 1000 Series lightweight access
point appears on the list, it has been configured successfully.
•
From the CLI, Web User Interface or Cisco WCS interface, configure the Cisco Aironet 1000 Series
lightweight access point with its Primary, Secondary, and Tertiary Cisco Wireless LAN Controller
names.
•
If you will be using the Cisco Aironet 1000 Series lightweight access point in a Controller Mobility
Group, set the Controller Mobility Group name using the CLI, Web User Interface or Cisco WCS
interface.
•
If required, use the CLI, Web User Interface or Cisco WCS interface to customize the Cisco Aironet
1000 Series lightweight access point-specific 802.11a, 802.11b and 802.11g network settings. Once
again, the two YELLOW LEDs indicate the states of the 802.11a and 802.11b/g networks. If any
part of the network is disabled, the corresponding YELLOW LED remains off.
Step 5
If everything works (the GREEN LED is on and the RED LED is off), disconnect the Cisco Aironet 1000
Series lightweight access point and take it to its final destination and install it as described later in this
document. If your Cisco Aironet 1000 Series lightweight access point fails this visual test, refer to
“Obtaining Technical Assistance” to return your Cisco Aironet 1000 Series lightweight access point.
Note
When you are installing a Cisco 1030 remote edge lightweight access point or a Layer 3 Cisco Aironet
1000 Series lightweight access point on a different subnet than the Cisco Wireless LAN Controller, BE
SURE that a DHCP server is available on the subnet where you will be installing the Cisco Aironet 1000
Series lightweight access point, and that the subnet has a route back to the Cisco Wireless LAN
Controller. Also be sure that the route back to the Cisco Wireless LAN Controller has destination UDP
ports 12222 and 12223 open for LWAPP communications. Ensure the route back to the Primary,
Secondary, and Tertiary Cisco Wireless LAN Controller allows IP packet fragments. Finally, be sure that
if address translation is used, that the Cisco Aironet 1000 Series lightweight access point and the Cisco
Wireless LAN Controller have a static 1-to-1 NAT to an outside address. (Port Address Translation is
not supported.)
Step 6
When you have installed and powered up the Cisco Aironet 1000 Series lightweight access point in its
final destination, verify that the LEDs are in the same state they were in at the end of Step 4.
•
If no LEDs are on, the Cisco Aironet 1000 Series lightweight access point is most likely not
receiving power.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
7
Installation and Configuration
Pre-Installation Configuration
Step 7
•
If the LEDs blink sequentially for more than five minutes, the Cisco Aironet 1000 Series lightweight
access point is unable to find its Primary, Secondary, or Tertiary Cisco Wireless LAN Controller.
Check the connection between the Cisco Aironet 1000 Series lightweight access point and the Cisco
Wireless LAN Controller, and be sure the Cisco Aironet 1000 Series lightweight access point and
the Cisco Wireless LAN Controller are either on the same subnet or that the Cisco Aironet 1000
Series lightweight access point has a route back to its Primary, Secondary, and Tertiary Cisco
Wireless LAN Controller.
•
If the Cisco Aironet 1000 Series lightweight access point is not on the same subnet as the Cisco
Wireless LAN Controller, be sure there is a DHCP server on the same subnet as the Cisco Aironet
1000 Series lightweight access point. Also, be sure that the route between the Cisco Aironet 1000
Series lightweight access point and the Cisco Wireless LAN Controller can process IP fragmented
packets.
If no LEDs are on, the Cisco Aironet 1000 Series lightweight access point is most likely not receiving
power. If all the LEDs blink sequentially for more than five minutes, the Cisco Aironet 1000 Series
lightweight access point is unable to find its Primary, Secondary, and Tertiary Cisco Wireless LAN
Controllers. Check the connection between the Cisco Aironet 1000 Series lightweight access point and
the Cisco Wireless LAN Controller, and be sure that they are either on the same subnet or that the Cisco
Aironet 1000 Series lightweight access point has a route back to its Primary, Secondary, and Tertiary
Cisco Wireless LAN Controller. Note that the Cisco 1030 remote edge lightweight access points at each
remote location must be on the same subnet to allow client roaming. Also, if the Cisco Aironet 1000
Series lightweight access point is not on the same subnet as the Cisco Wireless LAN Controller, be sure
there is a DHCP server on the same subnet as the Cisco Aironet 1000 Series lightweight access point.
After you have prepared all Cisco Aironet 1000 Series 802.11a/b/g lightweight access points,
reconfigure the Cisco Wireless LAN Controller so it is not the Master. A Master Cisco Wireless LAN
Controller should only be used for configuring Cisco Aironet 1000 Series 802.11a/b/g lightweight access
points and not in a working network. Note that the Master Cisco Wireless LAN Controller is normally
not used in a deployed network, so the Master Cisco Wireless LAN Controller setting is automatically
disabled upon reboot or OS code upgrade.
After completing “Pre-Installation Configuration” for all Cisco Aironet 1000 Series 802.11a/b/g
lightweight access points, continue with “Preparing Mounting Locations.”
Alternate Method of Preparing a Version 3.0 Cisco Aironet 1000 Series
Lightweight Access Point
If your Cisco Aironet 1000 Series lightweight access point has Operating System 3.0 or later, you may
choose to use this procedure.
Note
This procedure assumes that you are preparing a version 3.0 Cisco Aironet 1000 Series lightweight
access point to operate with a version 3.0 Cisco Wireless LAN Controller. It also assumes that your
Cisco Wireless LAN Controller is already operating in LWAPP Layer 3 Mode. It also assumes that you
are using the Internet Software Consortium (ISC) DHCP Server V3.0pl1. Finally, it assumes that if you
have deployed multiple Cisco Wireless LAN Controllers, the Cisco Wireless LAN Controller you use to
initialize the Cisco Aironet 1000 Series lightweight access point is in an existing Controller Mobility
Group with the Primary, Secondary, and Tertiary Cisco Wireless LAN Controllers you want to assign to
the new Cisco Aironet 1000 Series lightweight access point.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
8
Installation and Configuration
Pre-Installation Configuration
Configuration Setup
Figure 5
Configuration Setup
Configuring controller
Primary controller
Layer 2 and 3 devices
DHCP server
135676
Access points
Does My Cisco Aironet 1000 Series Lightweight Access Point Qualify for this Procedure?
Does My Cisco Aironet 1000 Series Lightweight Access Point Qualify for this Procedure?
•
If your 3.0 or later version Cisco Aironet 1000 Series lightweight access point(s) cannot be
configured for any reason using the following procedure, refer to the “Obtaining Technical
Assistance” section.
Configuration Steps for a Cisco 1000 Series Lightweight Access Point
1.
Configure the Internet Software Consortium (ISC) V3.0pl1 DHCP Server to provide the
vendor-specific Option 43 using the following entries:
option controller code 43 = text;
option controller “<Switch IP Address>”;
in which <Switch IP Address> is the IP address of the Cisco Wireless LAN Controller you
are going to use to prepare the Cisco Aironet 1000 Series lightweight access point, or which can be
a comma-delimited string of Cisco Wireless LAN Controller IP addresses.
(These commands direct all discovery messages for unconfigured Cisco Aironet 1000 Series
802.11a/b/g lightweight access points to the configuring Cisco Wireless LAN Controller.)
2.
Be sure the configuring Cisco Wireless LAN Controller is in LWAPP Layer 3 Mode (use the CLI
command show switchconfig to determine the mode; if it is set to Layer 3, use the CLI
command config switchconfig mode L2 to change it to Layer 2). Be sure that the
configuring Cisco Wireless LAN Controller is in the same Controller Mobility Group as the planned
Primary, Secondary, and Tertiary Cisco Wireless LAN Controllers, and that the configuring Cisco
Wireless LAN Controller DS Port is connected to the network.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
9
Installation and Configuration
Pre-Installation Configuration
3.
Note
Also be sure that the DHCP server is configured in the Cisco Wireless LAN Controller for both the
Management Interface and AP-Manager Interface using the CLI, Web User Interface, or Cisco WCS
user interface.
When you are installing a Cisco Aironet 1000 Series lightweight access point, a DHCP server must be
accessible by the Cisco Aironet 1000 Series lightweight access point.
4.
Take the Cisco Aironet 1000 Series lightweight access point out of the box and plug it into the
network so that it can request an IP address from the DHCP server.
5.
Apply power to the Cisco Aironet 1000 Series lightweight access point:
a. Use 802.3af-compatible PoE from the network equipment or from an orderable inline power
injector. If you do not have PoE available, use an orderable AC-to-48 VDC External Power
Supply plugged into the side of the Cisco Aironet 1000 Series lightweight access point.
Note
Cisco Aironet 1000 Series 802.11a/b/g lightweight access points support 802.3af Power over Ethernet
(PoE). These access points do not support Cisco prestandard PoE. Please use Cisco 802.3af capable PoE
switches or power injectors
b. After you power up the Cisco Aironet 1000 Series lightweight access point, the RED Alarm
LED comes on for about 15-20 seconds and then all the LEDs blink sequentially back and forth,
indicating that the Cisco Aironet 1000 Series lightweight access point is trying to find a Cisco
Wireless LAN Controller to connect to. This can continue for up to five minutes. If the Cisco
Aironet 1000 Series lightweight access point remains in this mode for more than five minutes,
the Cisco Aironet 1000 Series lightweight access point is unable to find the Master Cisco
Wireless LAN Controller. Check the connection between the Cisco Aironet 1000 Series
lightweight access point and the Cisco Wireless LAN Controller and be sure that they are on the
same subnet.
c. If the power light does not come on, check the power (it can be powered either with PoE or a
from an orderable Cisco Aironet 1000 Series lightweight access point External Power Supply.
6.
The Cisco Aironet 1000 Series lightweight access point requests an IP address from the DHCP
server, and the DHCP server returns an IP address for the Cisco Aironet 1000 Series lightweight
access point, and also returns the IP Address of the configuring Cisco Wireless LAN Controller.
After the Cisco Aironet 1000 Series lightweight access point finds the configuring Cisco Wireless
LAN Controller, it attempts to download the new Operating System code if the Cisco Aironet 1000
Series lightweight access point code version differs from the configuring Cisco Wireless LAN
Controller code version. While this is happening, the LEDs on the top of the Cisco Aironet 1000
Series lightweight access point blink simultaneously.
7.
After the Operating System code is downloaded, the Cisco Aironet 1000 Series lightweight access
point reboots. The GREEN LED turns on and the two YELLOW LEDs indicate the states of the
802.11a and 802.11b/g networks. If any part of the network is disabled in the configuring Cisco
Wireless LAN Controller, the corresponding YELLOW LED remains off.
– Note that the Red LED can light for about 10-20 seconds when the Cisco Aironet 1000 Series
lightweight access point reboots. If the RED LED comes on AND STAYS ON for more than a
minute, disconnect the Cisco Aironet 1000 Series lightweight access point and call Cisco
Technical Assistance Center (TAC).
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
10
Installation and Configuration
Pre-Installation Configuration
– From the CLI, Web User Interface or Cisco WCS interface, configure the Cisco Aironet 1000
Series lightweight access point with its Primary, Secondary, and Tertiary Cisco Wireless LAN
Controller names (any of which can be the name of the configuring Cisco Wireless LAN
Controllers).
– If required, use the CLI, Web User Interface or Cisco WCS interface to customize the Cisco
Aironet 1000 Series lightweight access point-specific 802.11a, 802.11b and 802.11g network
settings. Once again, the two YELLOW LEDs indicate the states of the 802.11a and 802.11b/g
networks. If any part of the network is disabled, the corresponding YELLOW LED remains off.
8.
Note
If everything works (the GREEN LED is on and the RED LED is off), reboot the Cisco Aironet 1000
Series lightweight access point and install it as described in this
document. If your Cisco Aironet 1000 Series lightweight access point fails this visual test, refer to
the “Obtaining Technical Assistance” section to return your Cisco Aironet 1000 Series 802.11a/b/g
lightweight access points.
When you are installing a Cisco 1030 remote edge lightweight access point or a Layer 3 Cisco Aironet
1000 Series lightweight access point on a different subnet than the Cisco Wireless LAN Controller, BE
SURE that a DHCP server is available on the subnet where you will be installing the Cisco Aironet 1000
Series lightweight access point and that the subnet has a route back to the Primary, Secondary, and
Tertiary Cisco Wireless LAN Controller. Ensure that the route back to the Cisco Wireless LAN
Controller has destination UDP ports 12222 and 12223 open for LWAPP communications. Ensure the
route back to the Primary, Secondary, and Tertiary Cisco Wireless LAN Controller allows IP packet
fragments. Finally, be sure that if address translation is used, the Cisco Aironet 1000 Series lightweight
access point and the Cisco Wireless LAN Controller have a static 1-to-1 NAT to an outside address. (Port
Address Translation is not supported.)
9.
When you have installed and powered up the Cisco Aironet 1000 Series lightweight access point in
its final destination, verify that the LEDs are in the same state they were in at the end of Step 7.
– If no LEDs are on, the Cisco Aironet 1000 Series lightweight access point is most likely not
receiving power.
– If the LEDs blink sequentially for more than five minutes, the Cisco Aironet 1000 Series
lightweight access point is unable to find its Primary, Secondary, or Tertiary Cisco Wireless
LAN Controller. Check the connection between the Cisco Aironet 1000 Series lightweight
access point and the Cisco Wireless LAN Controller, and be sure that they are either on the same
subnet or that the Cisco Aironet 1000 Series lightweight access point has a route back to its
Primary, Secondary, and Tertiary Cisco Wireless LAN Controllers.
– Note that the Cisco 1030 remote edge lightweight access points at each remote location must be
on the same subnet to allow client roaming. Also, if the Cisco Aironet 1000 Series lightweight
access point is not on the same subnet as the Cisco Wireless LAN Controller, be sure that a
DHCP server is accessible on the same subnet as the Cisco Aironet 1000 Series lightweight
access point.
After completing “Pre-Installation Configuration” for all Cisco Aironet 1000 Series 802.11a/b/g
lightweight access points, continue with “Preparing Mounting Locations.”
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
11
Installation and Configuration
Preparing Mounting Locations
Preparing Mounting Locations
On your map, you should have the Cisco Aironet 1000 Series lightweight access point locations,
mounting options, and power options.
Note
BE SURE that plenum-mounted Cisco Aironet 1000 Series 802.11a/b/g lightweight access points use
only the metal Projection-Mount and Flush-Mount brackets (not the Ceiling-Mount Base or the
Hanging-Ceiling Clips) and are powered using PoE to comply with safety regulations. Also, external
antennas are NOT to be used when installing Cisco Aironet 1000 Series 802.11a/b/g lightweight access
points in a plenum.
1.
Find the required mounting locations.
– Use the ceiling-mount base to mark the wall or ceiling locations for sheet metal, drywall, or
other screws. Be sure to leave enough space around the Cisco Aironet 1000 Series lightweight
access point and base to plug the CAT-5 cable, optional external antenna cable(s), optional
power supply cable, and optional Kensington MicroSaver Security Cable into the sides of the
Cisco Aironet 1000 Series lightweight access point.
Factory-Supplied Mounting Options
A. Ceiling-mount base
B. Hanging-ceiling clips
135663
Figure 6
– Alternatively, attach the hanging ceiling clips to the Cisco Aironet 1000 Series lightweight
access point. Be sure you leave enough space around the Cisco Aironet 1000 Series lightweight
access point to plug the CAT-5 cable, optional external antenna cable(s), optional power supply
cable, and optional Kensington MicroSaver Security Cable into the sides of the Cisco Aironet
1000 Series lightweight access point.
– Alternatively, use the optional mounting bases or brackets to mark the wall or ceiling locations
for sheet metal, drywall, or other screws. Be sure to leave enough space around the Cisco
Aironet 1000 Series lightweight access point and brackets to plug the CAT-5 cable, optional
external antenna cable(s), optional power supply cable, and optional Kensington MicroSaver
Security Cable into the sides of the Cisco Aironet 1000 Series lightweight access point.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
12
Installation and Configuration
Preparing Mounting Locations
Factory-Orderable Mounting Brackets
135661
Figure 7
A. Projection-mount bracket
B. Flush-mount bracket
2.
If necessary, drill holes for the various cables where they can be mostly hidden from casual view.
When you are mounting the Cisco Aironet 1000 Series lightweight access point using an optional
orderable projection-mount L-bracket (the one with two long legs), the cables can be routed through
the 5/8-in. (15.9 mm) holes in the bracket.
3.
Route the CAT-5, optional power supply, optional external antenna cable(s), and optional
Kensington MicroSaver Security cables to where they can plug into the Cisco Aironet 1000 Series
lightweight access point. Be sure to leave about 6 in. (15 cm) of slack in the cables for future
modifications.
4.
Attach the brackets to the wall or ceiling, or install screws for ceiling-mount base:
– Where you are going to use the projection-mount or flush-mount bracket, use customer-supplied
sheet metal, drywall, or other screws to attach the bracket to the ceiling or wall.
– Where you are going to use the ceiling-mount base, install customer-supplied sheet metal,
drywall, or other screws with 1/4 in. (6.35 mm) or smaller heads protruding from the ceiling
about 0.1 in. (2.5 mm).
You are now ready to install the Cisco Aironet 1000 Series 802.11a/b/g lightweight access points.
Continue with “Mounting the Cisco Aironet 1000 Series Lightweight Access Points.”
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
13
Installation and Configuration
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
Mounting the Cisco Aironet 1000 Series Lightweight Access
Points
Using the supplied or optional orderable Cisco Aironet 1000 Series lightweight access point mounting
kits, mount each Cisco Aironet 1000 Series lightweight access point in its indicated location, oriented
as shown on the map. Note that you can mount the Cisco Aironet 1000 Series 802.11a/b/g lightweight
access points in the ceiling plenum or below the ceiling, but that they perform best when mounted below
the ceiling.
Note
The Cisco Aironet 1000 Series lightweight access point supports Antenna Sectorization, which can be
used to increase the number of clients and client throughput in a given air space. Installers can mount
two Cisco Aironet 1000 Series 802.11a/b/g lightweight access points back-to-back and the Network
operator can disable the second antenna in both Cisco Aironet 1000 Series 802.11a/b/g lightweight
access points to create a 360-degree coverage area with two sectors.
The Cisco Aironet 1000 Series 802.11a/b/g lightweight access points can be mounted in one of the
following configurations:
•
Ceiling-Mount Base -- Refer to Ceiling Mount Base.
•
Ceiling-Mount Clips -- Refer to Ceiling-Mount Clips.
•
Projection Wall Mount -- Refer to Projection Wall Mount.
•
Flush Wall Mount -- Refer to Flush Wall Mount.
•
Ceiling-Mount Bezel -- Refer to the Cisco Aironet 1000 Series Lightweight Access Point
Ceiling-Mount Bezel Kit Installation and Configuration Guide.
Ceiling Mount Base
When you are mounting the Cisco Aironet 1000 Series lightweight access point in the middle of a ceiling
(flat sides toward the room or hallway), use the ceiling-mount base to mount the Cisco Aironet 1000
Series lightweight access point as shown in the following figure and as described below:
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
14
Installation and Configuration
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
Attaching the Cisco Aironet 1000 Series Lightweight Access Point and Ceiling-Mount
Base
135664
Figure 8
Note
1.
Copy the MAC address(es) from the label(s) on the Cisco Aironet 1000 Series lightweight access
point onto the corresponding location on the map. MAC addresses have the format 00xxxxxxxxxx.
2.
Attach the ceiling-mount base to the bottom of the Cisco Aironet 1000 Series lightweight access
point using the factory-supplied machine screws and washers.
3.
Position the ceiling-mount base so its keyhole slots are partly on the drywall, sheet metal, or other
screw heads installed in “Preparing Mounting Locations.”
If the screws do not securely hold the ceiling-mount base, remove the Cisco Aironet 1000 Series
lightweight access point and adjust the screws until they hold the ceiling-mount base securely.
4.
Note
Attach the cables to the sides of the Cisco Aironet 1000 Series lightweight access point.
When the Cisco Aironet 1000 Series lightweight access point is powered up and is associated with a
Cisco Wireless LAN Controller (Green/Power and Yellow/802.11b/g and/or Yellow or Amber/802.11a
LEDs lit), the Cisco Aironet 1000 Series lightweight access point is broadcasting its beacon signal(s).
When this happens, complete the installation as quickly as possible to remove yourself from within 8 in.
(20 cm) of the Cisco Aironet 1000 Series lightweight access point to comply with FCC RF radiation
exposure guidelines.
5.
Slide the ceiling-mount base onto the drywall, sheet metal, or other screw heads until it fits snugly
in place.
You installed the access point. Repeat “Mounting the Cisco Aironet 1000 Series Lightweight Access
Points” for each location, and then continue with “Returning MAC Information.”
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
15
Installation and Configuration
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
Ceiling-Mount Clips
When you are mounting the Cisco Aironet 1000 Series lightweight access point on the extruded
aluminium rails of a hanging ceiling, use the ceiling-mount clips to mount the Cisco Aironet 1000 Series
lightweight access point as shown in the following figure and as described below:
Assembling the Cisco Aironet 1000 Series Lightweight Access Point and
Ceiling-Mount Clips
135665
Figure 9
1.
Copy the MAC address(es) from the label(s) on the Cisco Aironet 1000 Series lightweight access
point onto the corresponding location on the map. MAC addresses have the format 00xxxxxxxxxx.
2.
Attach the ceiling-mount clips to the bottom of the Cisco Aironet 1000 Series lightweight access
point using the factory-supplied machine screws and washers.
3.
Snap the ceiling-mount clips onto a hanging ceiling rail.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
16
Installation and Configuration
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
Clipping the Cisco Aironet 1000 Series Lightweight Access Point and Ceiling-Mount
Clips to a Hanging-Ceiling Rail
135674
Figure 10
Note
4.
Attach the cables to the sides of the Cisco Aironet 1000 Series lightweight access point.
•
Be sure the cables are routed away from the Cisco Aironet 1000 Series lightweight access point
antennas.
•
When the Cisco Aironet 1000 Series lightweight access point is powered up and is associated with a
Cisco Wireless LAN Controller (Green/Power and Yellow/802.11b/g and/or Yellow or Amber/802.11a
LEDs lit), the Cisco Aironet 1000 Series lightweight access point is broadcasting its beacon signal(s).
When this happens, complete the installation as quickly as possible to remove yourself from within
8 in.(20 cm) of the Cisco Aironet 1000 Series lightweight access point to comply with FCC RF radiation
exposure guidelines.
You have installed the Cisco Aironet 1000 Series lightweight access point. Repeat “Mounting the Cisco
Aironet 1000 Series Lightweight Access Points” for each Cisco Aironet 1000 Series lightweight access
point location, and then continue with “Returning MAC Information.”
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
17
Installation and Configuration
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
Projection Wall Mount
When you are mounting the Cisco Aironet 1000 Series lightweight access point out from a wall (flat
sides along the wall or hallway), use an optional separately orderable factory-orderable
projection-mount L-bracket.
1.
The Cisco Aironet 1000 Series lightweight access point threaded holes have precision-depth threads. Do
not overtighten the screws, or the bracket will not fit under the screw heads.
Figure 11
Attaching the Mounting Screws and Spring Washers to the Cisco Aironet 1000 Series
Lightweight Access Point
A. Screws and spring washers
Note
B. Completed assembly
135667
Note
Before proceeding, gently screw the two factory-supplied screws and spring washers into the bottom
of the Cisco Aironet 1000 Series lightweight access point. Be sure the spring washers have their
convex (high center sections) pointing toward the screw heads.
2.
Copy the MAC address(es) from the label(s) on the Cisco Aironet 1000 Series lightweight access
point onto the corresponding location on the map. MAC addresses have the format 00xxxxxxxxxx.
3.
You have already attached the projection-mount L-bracket to the wall in “Preparing Mounting
Locations.”
4.
Slide the screws into the keyhole slots on the mounting bracket as shown in the following figure.
If the screws do not securely hold the bracket, remove the Cisco Aironet 1000 Series lightweight access
point and adjust the screws until they securely hold the bracket.
Figure 12
Attaching the Cisco Aironet 1000 Series Lightweight Access Point to the
Projection-Mount Bracket
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
18
Installation and Configuration
135671
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
Note
5.
Attach the cables to the sides of the Cisco Aironet 1000 Series lightweight access point.
•
Be sure the cables are routed away from the Cisco Aironet 1000 Series lightweight access point
antennas.
•
When the Cisco Aironet 1000 Series lightweight access point is powered up and is associated with
a Cisco Wireless LAN Controller (Green/Power and Yellow/802.11b/g and/or Yellow or
Amber/802.11a LEDs lit), the Cisco Aironet 1000 Series lightweight access point begins
broadcasting its beacon signal(s). When this happens, complete the installation as quickly as
possible to remove yourself from within 8 in. (20 cm) of the Cisco Aironet 1000 Series lightweight
access point to comply with FCC RF radiation exposure guidelines.
You have installed the Cisco Aironet 1000 Series lightweight access point. Repeat “Mounting the Cisco
Aironet 1000 Series Lightweight Access Points” for each Cisco Aironet 1000 Series lightweight access
point location, and then continue with “Returning MAC Information.”
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
19
Installation and Configuration
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
Flush Wall Mount
Flush Wall Mount
When you are mounting the Cisco Aironet 1000 Series lightweight access point against a wall (flat side
toward the inside of the building), use an optional separately orderable factory-orderable flush-mount
bracket.
1.
The Cisco Aironet 1000 Series lightweight access point threaded holes have precision-depth threads. Do
not overtighten the screws, or the bracket will not fit under the screw heads.
Figure 13
Attaching the Mounting Screws and Spring Washers to the Cisco Aironet 1000 Series
Lightweight Access Point
A. Screws and spring washers
Note
B. Completed assembly
135667
Note
Before proceeding, gently screw the two factory-supplied screws and spring washers into the bottom
of the Cisco Aironet 1000 Series lightweight access point. Be sure the spring washers have their
convex (high center sections) pointing toward the screw heads.
2.
Copy the MAC address(es) from the label(s) on the Cisco Aironet 1000 Series lightweight access
point onto the corresponding location on the map. MAC addresses have the format 00xxxxxxxxxx.
3.
You have already attached the flush-mount bracket to the wall in “Preparing Mounting Locations.”
4.
Slide the screws into the keyhole slots on the mounting bracket as shown in the following figure.
•
Be sure the side of the Cisco Aironet 1000 Series lightweight access point with the door is facing
away from the wall. This ensures that the correct antenna is facing the building, and makes future
upgrades easier.
•
If the screws do not securely hold the bracket, remove the Cisco Aironet 1000 Series lightweight
access point and adjust the screws until they securely hold the bracket.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
20
Installation and Configuration
Mounting the Cisco Aironet 1000 Series Lightweight Access Points
Attaching the Cisco Aironet 1000 Series Lightweight Access Point to the Flush-Mount
Bracket
135672
Figure 14
Note
5.
Attach the cables to the sides of the Cisco Aironet 1000 Series lightweight access point.
•
Be sure the cables are routed away from the Cisco Aironet 1000 Series lightweight access point
antennas.
•
When the Cisco Aironet 1000 Series lightweight access point is powered up and is associated with
a Cisco Wireless LAN Controller (Green/Power and Yellow/802.11b/g and/or Yellow or
Amber/802.11a LEDs lit), the Cisco Aironet 1000 Series lightweight access point begins
broadcasting its beacon signal(s). When this happens, complete the installation as quickly as
possible to remove yourself from within 8 in. (20 cm) of the Cisco Aironet 1000 Series lightweight
access point to comply with FCC RF radiation exposure guidelines.
You have installed the Cisco Aironet 1000 Series lightweight access point. Repeat “Mounting the Cisco
Aironet 1000 Series Lightweight Access Points” for each Cisco Aironet 1000 Series lightweight access
point location, and then continue with “Returning MAC Information.”
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
21
Installation and Configuration
Returning MAC Information
Returning MAC Information
When you have completed the installations as outlined in “Mounting the Cisco Aironet 1000 Series
Lightweight Access Points,” return the MAC addresses and their locations on the maps or floor plans to
the network planner or manager. The Network operators will use the MAC address and location
information to create maps for precise wireless Operating System management.
Also return any unused mounting kit hardware and external power supplies to the network planner or
manager for use in future deployments.
Note
Please remind the Network Planner or Manager that now is a good time to register the Cisco Aironet
1000 Series 802.11a/b/g lightweight access points.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
22
A P P E N D I X
A
Planning Notes
•
About Cables
•
About External Antennas
•
About Mounting Options
•
About Physical Security
•
FCC Statements for Cisco Aironet 1000 Series Lightweight Access Points
•
Safety Considerations
•
You will run one CAT-5 Ethernet cable from the Cisco Aironet 1000 Series lightweight access point
to a network device or a PoE injector/hub.
•
When a Cisco 1000 Series lightweight access point will be mounted below the ceiling using the
ceiling mount or wall mount brackets, you may have to drill a hole into the ceiling plenum to run
the CAT-5 cable to the wiring closet. When the CAT-5 cable cannot be run through the ceiling
plenum, find another path to route the cable from the Cisco Aironet 1000 Series lightweight access
point to the wiring closet.
•
When the Cisco Aironet 1000 Series lightweight access point will be mounted above the ceiling
using the ceiling mount or wall mount brackets, run the CAT-5 cable to the wiring closet through the
ceiling plenum. When the CAT-5 cable cannot be run through the ceiling plenum, find another path
to route the cable from the Cisco Aironet 1000 Series lightweight access point to the wiring closet.
•
When you are powering the Cisco Aironet 1000 Series lightweight access point from AC power,
route the power supply cable from the AC electrical outlet to the Cisco Aironet 1000 Series
lightweight access point. Be sure you secure the AC power plug so it will be difficult for people to
pull on the power cord or unplug the power supply from the AC power outlet.
•
When you are powering the Cisco Aironet 1000 Series lightweight access point from a PoE source
(a network device, or a PoE injector/hub), you do not need to route a separate power cable to the
Cisco Aironet 1000 Series lightweight access point, because the Cisco Aironet 1000 Series
lightweight access point will receive its power across the CAT-5 Ethernet cable. Return the power
supply to the wireless network planner/manager.
About Cables
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
A-1
Appendix A
Planning Notes
About External Antennas
Note
Caution
.As described in the AP1010 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Point
Installation and Configuration Guide, the AP1010 Cisco Aironet 1000 Series 802.11a/b/g lightweight
access points are designed to be used exclusively with the internal high-gain antennas and have no jacks
for external antennas.
External antennas are NOT to be used when installing Cisco Aironet 1000 Series 802.11a/b/g
lightweight access points in a plenum.
•
When you are attaching external antennas to the AP1020 and AP1030 Cisco Aironet 1000 Series
lightweight access point, use cables with female reverse-TNC connectors to connect antennas to the
ports on the side of the Cisco Aironet 1000 Series lightweight access point. See the following figure
for antenna port markings.
Figure A-1
Cisco Aironet 1000 Series 802.11a/b/g Lightweight Access Point External Antenna
Port Markings
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
A-2
78-17147-01
Appendix A
Planning Notes
About Mounting Options
Caution
Note
Plenum-mounted Cisco Aironet 1000 Series 802.11a/b/g lightweight access points MUST BE powered
using PoE to comply with safety regulations.
•
Because the Cisco Aironet 1000 Series lightweight access point internal antennas have been
designed to reduce inter-floor interference, it is strongly recommended that you mount the Cisco
Aironet 1000 Series lightweight access point standing or hanging straight up or down.
•
You can mount the Cisco Aironet 1000 Series 802.11a/b/g lightweight access points in the ceiling
plenum or below the ceiling using the ceiling mount base or wall mount brackets, but the Cisco
Aironet 1000 Series 802.11a/b/g lightweight access points perform best when mounted below the
ceiling.
•
External antennas are NOT to be used when installing Cisco Aironet 1000 Series 802.11a/b/g
lightweight access points in a plenum.
•
When you are mounting the Cisco Aironet 1000 Series lightweight access point in the middle of a
ceiling, ceiling plenum, or hallway, you will typically use the color-coordinated ceiling-mount base
to stabilize the Cisco Aironet 1000 Series lightweight access point after it is mounted. Use the
mounting base to mark the sheet metal, drywall, or other screw locations.
The mounting base attaches to the bottom of the Cisco Aironet 1000 Series lightweight access point
with two supplied screws, and then the assembly slides and locks onto two sheet metal, drywall, or
other screws.
•
When you are mounting the Cisco Aironet 1000 Series lightweight access point out from a wall (flat
sides along the room or hallway), use the projection-mount L-bracket supplied with the Cisco
Aironet 1000 Series lightweight access point. Use the L-bracket to mark the sheet metal, drywall,
or other screw locations.
•
When you are mounting the Cisco Aironet 1000 Series lightweight access point against a wall (flat
Side A toward the inside of the building), use the flush-mount bracket supplied with the Cisco
Aironet 1000 Series lightweight access point. The flush-mount L-bracket is the one with one long
and one short leg. Use the L-bracket to mark the sheet metal, drywall, or other screw locations.
About Mounting Options
Note
•
Because the Cisco Aironet 1000 Series lightweight access point internal antennas have been
designed to reduce inter-floor interference, it is strongly recommended that you mount the Cisco
Aironet 1000 Series lightweight access point standing or hanging straight up or down.
•
You can mount the Cisco Aironet 1000 Series 802.11a/b/g lightweight access points in the ceiling
plenum or below the ceiling using the ceiling mount base or wall mount brackets, but the Cisco
Aironet 1000 Series 802.11a/b/g lightweight access points perform best when mounted below the
ceiling.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
A-3
Appendix A
Caution
Planning Notes
Plenum-mounted Cisco Aironet 1000 Series 802.11a/b/g lightweight access points MUST BE powered using
PoE to comply with safety regulations.
•
When you are mounting the Cisco Aironet 1000 Series lightweight access point in the middle of a
ceiling, ceiling plenum, or hallway, you will typically use the color-coordinated ceiling-mount base
to stabilize the Cisco Aironet 1000 Series lightweight access point after it is mounted. Use the
mounting base to mark the sheet metal, drywall, or other screw locations.
•
The mounting base attaches to the bottom of the Cisco Aironet 1000 Series lightweight access point
with two supplied screws, and then the assembly slides and locks onto two sheet metal, drywall, or
other screws.
•
When you are mounting the Cisco Aironet 1000 Series lightweight access point out from a wall (flat
sides along the room or hallway), use the projection-mount L-bracket supplied with the Cisco
Aironet 1000 Series lightweight access point. Use the L-bracket to mark the sheet metal, drywall,
or other screw locations.
•
When you are mounting the Cisco Aironet 1000 Series lightweight access point against a wall (flat
Side A toward the inside of the building), use the flush-mount bracket supplied with the Cisco
Aironet 1000 Series lightweight access point. The flush-mount L-bracket is the one with one long
and one short leg. Use the L-bracket to mark the sheet metal, drywall, or other screw locations.
About Physical Security
Regardless of the mounting type selected, the Cisco Aironet 1000 Series lightweight access point can be
secured with a Kensington MicroSaver Security Cable. If required, use any MicroSaver Security Cable to
attach either side of your Cisco Aironet 1000 Series lightweight access point to a solid beam, pipe, or support.
FCC Statements for Cisco Aironet 1000 Series Lightweight Access Points
FCC Statements for Cisco Aironet 1000 Series Lightweight Access Points
This section includes the following FCC statements for the Cisco Aironet 1000 Series lightweight access
point:
•
Class A Statement
•
RF Radiation Hazard Warning
•
Non-Modification Statement
•
Deployment Statement
Class A Statement
Class A Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense. [cfr reference 15.105]
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
A-4
78-17147-01
Appendix A
Planning Notes
RF Radiation Hazard Warning
RF Radiation Hazard Warning
To ensure compliance with FCC RF exposure requirements, this device must be installed in a location
such that the antenna of the device will be greater than 20 cm (8 in.) from all persons. Using higher gain
antennas and types of antennas not covered under the FCC certification of this product is not allowed.
Installers of the radio and end users of the Cisco Wireless LAN Solution must adhere to the installation
instructions provided in this manual.
Non-Modification Statement
Non-Modification Statement
Use only the supplied internal antenna, or external antennas supplied by the manufacturer. Unauthorized
antennas, modifications, or attachments could damage the badge and could violate FCC regulations and
void the user’s authority to operate the equipment.
External Antennas
The AIR-AP1020-A-K9, AIR-AP1020-E-K9, AIR-AP1020-J-K9, AIR-AP1030-A-K9,
AIR-AP1030-E-K9, and AIR-AP1030-J-K9 Cisco Aironet 1000 Series IEEE 802.11a/b/g lightweight
access points can be used with external antennas with the following characteristics:
•
5 GHz patch antenna: 6 dBi net gain.
•
2.4 GHz patch antenna: 6 dBi net gain.
Deployment Statement
This product is certified for indoor deployment only. Do not install or use this product outdoors.
EU Regulatory Information
Compliance Information for Cisco Aironet 1000 Series IEEE 802.11a/b/g lightweight access points:
1.
Standards met:
– Radio: EN 301 328, EN 301 893
– EMC: EN 301489-1, EN 301 489-17
– Safety: EN 60950
– RF Safety: EN 50371
Note
2.
CE Marking: Cisco Aironet 1000 Series 802.11a/b/g lightweight access points are identified with
this CE marker:
3.
EU Country Restriction:
•
The Cisco Aironet 1000 Series IEEE 802.11a/b/g lightweight access point is intended for indoor use
only.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
A-5
Appendix A
•
Planning Notes
The Cisco Aironet 1000 Series IEEE 802.11a/b/g lightweight access point meets EU DFS
requirement.
Generally, the 5150-5350 MHz, 5470-5750 MHz, and 2400-2483.5 MHz bands are allowed in most EU
countries. However, there are several country specific restrictions that apply to different bands on a
country-by-country basis.
The following entries specify countries with specific restrictions:
Note
These restrictions may evolve. It is recommended that you check with their local authorities for latest
requirements
•
Austria - Only transmission within the frequency band 5150-5250 MHz is allowed. The band
5470-5750 MHz is not allowed.
•
Belgium - The frequency band 5470-5750 MHz is not allowed.
•
France - The frequency band 5470-5750 MHz is not allowed.
•
Portugal - Integral antenna is required.
•
Switzerland - The frequency band 5470-5750 MHz is not allowed.
•
Czech - The frequency band 5470-5750 MHz is not allowed.
•
Slovak Republic - The frequency band 5470-5750 MHz is not allowed.
Industry Canada Required User Information for Cisco Aironet 1000 Series
Lightweight Access Points
Industry Canada Required User Information for Cisco Aironet 1000 Series Lightweight Access Points
This device has been designed to operate with antennae having maximum gains of 7.8 dBi (2.4 GHz) and
7.4 dBi (5 GHz).
Antennae having higher gains is strictly prohibited per regulations of Industry Canada. The required
antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (EIRP) is not more than that required for successful
communication.
Safety Considerations
Warning
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.
Statement 1071
Safety Considerations
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
A-6
78-17147-01
Appendix A
Planning Notes
Warning
Warning
Waarschuwing
Varoitus
•
The AP1010, AP1020, and AP1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g lightweight access
points with or without external antenna ports are only intended for installation in Environment A as
defined in IEEE 802.3af. All interconnected equipment must be contained within the same building
including the interconnected equipment's associated LAN connections.
•
For AP1020 and AP1020 Cisco Aironet 1000 Series IEEE 802.11a/b/g lightweight access points
provided with optional external antenna ports, be sure that all external antennas and their associated
wiring are located entirely indoors. The Cisco Aironet 1000 Series 802.11a/b/g lightweight access
points and their optional external antennas are not suitable for outdoor use.
•
BE SURE that plenum-mounted Cisco Aironet 1000 Series 802.11a/b/g lightweight access points
are powered using PoE to comply with safety regulations.
•
Suitable for use in environmental air space in accordance with Section 300.22.C of the National
Electrical Code, and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1,
C22.1.
•
When used below dropped ceiling use a UL Listed ITE power adapter (QQGQ) marked LPS or a
Listed Direct Plug-in Adapter (EPBU) marked Class 2 with output rated 48 V, 0.4 A.
DGT statement for products that operate at both 2.4 GHz band and 5 GHz band:
This equipment must be grounded. Never defeat the ground conductor or operate the
equipment in the absence of a suitably installed ground conductor. Contact the appropriate
electrical inspection authority or an electrician if you are uncertain that suitable grounding is
available. Statement 1024
Deze apparatuur dient geaard te zijn. De aardingsleiding mag nooit buiten werking worden
gesteld en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze
geïnstalleerde aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor
elektrische inspecties of met een elektricien als u er niet zeker van bent dat er voor passende
aarding gezorgd is.
Laitteiden on oltava maadoitettuja. Älä koskaan ohita maajohdinta tai käytä laitteita ilman
oikein asennettua maajohdinta. Ota yhteys sähkötarkastusviranomaiseen tai sähköasentajaan,
jos olet epävarma maadoituksen sopivuudesta.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
A-7
Appendix A
Attention
Warnung
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Planning Notes
Cet équipement doit être mis à la masse. Ne jamais rendre inopérant le conducteur de masse
ni utiliser l'équipement sans un conducteur de masse adéquatement installé. En cas de doute
sur la mise à la masse appropriée disponible, s'adresser à l'organisme responsable de la
sécurité électrique ou à un électricien.
Dieses Gerät muss geerdet sein. Auf keinen Fall den Erdungsleiter unwirksam machen oder
das Gerät ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht
sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an die zuständige
Inspektionsbehörde oder einen Elektriker.
Questa apparecchiatura deve essere dotata di messa a terra. Non escludere mai il conduttore
di protezione né usare l'apparecchiatura in assenza di un conduttore di protezione installato
in modo corretto. Se non si è certi della disponibilità di un adeguato collegamento di messa a
terra, richiedere un controllo elettrico presso le autorità competenti o rivolgersi a un
elettricista.
Dette utstyret må jordes. Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert
jordingsleder. Ta kontakt med fagfolk innen elektrisk inspeksjon eller med en elektriker hvis
du er usikker på om det finnes velegnet jordning.
Este equipamento deve ser aterrado. Nunca anule o fio terra nem opere o equipamento sem
um aterramento adequadamente instalado. Em caso de dúvida com relação ao sistema de
aterramento disponível, entre em contato com os serviços locais de inspeção elétrica ou um
eletricista qualificado.
Este equipo debe estar conectado a tierra. No inhabilite el conductor de tierra ni haga
funcionar el equipo si no hay un conductor de tierra instalado correctamente. Póngase en
contacto con la autoridad correspondiente de inspección eléctrica o con un electricista si no
está seguro de que haya una conexión a tierra adecuada.
Denna utrustning måste jordas. Koppla aldrig från jordledningen och använd aldrig
utrustningen utan en på lämpligt sätt installerad jordledning. Om det föreligger osäkerhet
huruvida lämplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker
kontaktas.
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
A-8
78-17147-01
Appendix A
Planning Notes
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
A-9
Appendix A
Planning Notes
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
A-10
78-17147-01
INDEX
A
P
Alternate Method of Preparing a Version 3.0 Cisco Aironet
1000 Series 8
Preface
Preparing a Version 3.0 Cisco Aironet 1000 Series
Lightweight Access Point 5
Preparing Mounting Locations
C
Projection Wall Mount
Ceiling Mount Base
14
Ceiling-Mount Clips
16
Collecting Required Tools and Supplies
Configuration Setup
Conventions
v
4
18
R
Returning MAC Information
5
12
22
v
F
Flush Wall Mount
20
I
Installation and Configuration
1
M
Mounting the Cisco Aironet 1000 Series Lightweight
Access Points 14
O
Obtaining Documentation
vi
Obtaining Technical Assistance
viii
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
78-17147-01
IN-1
Index
AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide
IN-2
78-17147-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement