Axis 211 Installation guide

Axis 211 Installation guide
CAXIS 210/210A/211/211A Installation Guide
Page 3 )
AXIS 210/210A/211/211A
Installation Guide
This installation guide provides instructions for installing the AXIS 210/21 OA/211 /211A
Network Camera on your network. For all other aspects of using the product, please see the
User's Manual, available on the CD included in this package, or from www.axis.com/techsup
lnstallation steps
1.
2.
3.
4.
5.
6.
7.
Check the package contents against the list below.
Hardware overview. See page 4.
Install the hardware. See page 6.
Set an IP address. See page 7.
Set the password. See page 10.
Adjust the focus. See page 11.
Change the camera's web interface language
(optional). See page 12.
Important!
This product must be used in
compliance with local laws
and regulations.
Package contents
Item
Models/variants/notes
Network camera
• AXIS 210
• AXIS 210A: PoE, two-way audio and built-in microphone
• AXIS 211: PoE, Varifocal DC-iris lens
• AXIS 211A: PoE, two-way audio and built-in microphone, Varifocal DC-iris
lens
PS-Kindoorpowersupp~
Europe, UK, Australia, USA/Japan, Argentina, Korea
(country specific)
Camera stand
Supplied with mounting screws
Terminal block connector
4-pin connector block for connecting external devices to the I/O terminal connector
CD
Axis Network Video Product CD, including installation tools a nd other software, product documentation
Printed Materials
AXIS 210/210A!211!211A Installatio'n Guide (this document)
Axis Warranty Document
AXIS 210!210A!211!21 'IA Installation Guide
Page 4
( AXIS 210!210A!211!211A Installation Guide
Hardware overview
Page 5 )
Rear panel
AX1S 210/AX1S 210A
AX1S 211/AX1S 211A
Iele/wide puller
DC-Iris control cable
(AXIS 211/211A)
\
x'~~~~i~~~~~j~\
External microphone/line input Audio output
(AXIS 21OA/211A)
(AXIS 210A/211A)
Focus puller
I/O terminal
connector
Power connector
Network connector and PoE
(AXIS 21OA!211/211A)
Focus puller
Note:
Depending on the product version of your AXIS 21O/210A/211/211A, you will see
one of two different types ofI!O ternminal connectors. See I/O terminal COIll1eCtor, on page 15.
Underside
Dimensions
o
4----ItH-----1\\--Internal microphone
(AXIS 21OA/AXIS 21lA)
AXIS 210!210A:
HxWxD = 38 x 88 x 157mm (1.5" x 3.4" x 6.2")
Weight (AXIS 210) = 305g (O.67Ib) excl. power supply
Weight (AXIS 210A) = 325g (O.72lb) excl. power supply
AXIS 211!211A:
HxWxD = 38 x 95 x 178mm (1.5" x 3.7" x 7")
Weight = 345g (O.76Ib) excl. power supply
Serial number
Control button
"m;Q:1111.(101.(11
SiN:00411BCOMAOA
UDlIllllIllUllllllllllllillllUU
O(€
Power indicator
Network indicator
AXIS 210/21 0A/211/2rlAlhstaliation Guide
( AXIS 210/21 OA/211/211 A Installation Guide
Assign an lP address
lnstall the hardware
I
!III
IMPORTANT! - The 210/210A is designed for indoor use only, and must
always be positioned where it is not exposed to direct sunlight or strong
halogen light, which can cause permanent damage to the camera's image
sensor. Damage as a result of exposure to strong light is not covered by the
Axis warranty.
IMPORTANT! - The AXIS 211/211A is designed for indoor and outdoor use. To
use the camera outdoors, it must be installed in an approved outdoor housing.
Please see www.axis.com for more information on outdoor housings.
To make it accessible on the network, the AXIS 210/21OA/211/211A must be assigned an IP
address.
Depending on the number of cameras you wish to install, the recommended method for
assigning IF addresses in Windows is either AXIS IP Utility or AXIS Camera Management.
Use the method that best suits your purpose.
Both of these free applications are available on the Axis Network Video Product CD supplied
with this product, or they can be downloaded from www.axis.com/techsup
Recommended for
Operating system
AXIS IP Utility
See page 8
Single camera
Small installations
Windows
AXIS Camera Management
See page 9
Multiple cameras
Large installations
Installation on a different subnet
Windows 2000
Windows XP Pro
Windows 2003 Server
Method
Connect the camera
[!E
k§
1.
Page 7 )
Connect the Network Camera to your network using a standard network cable. Using
Shielded Twisted Pair (STP) cables is recommended.
2. Optionally connect external input/output devices, e.g. alarm devices. See page 15 for
information on the terminal connector pins.
3. Optionally, connect an active speaker and/or external microphone.
4. Connect power, using one of the methods listed below:
•
•
•
The supplied power connector.
Power over Ethernet (PoE). If available, this is automatically detected when the
network cable is connected (see above).
The 1/0 terminal connector on the rear panel.
5. Check that the indicator LED:s indicate the correct conditions. See the table on page 16
for further details. Note that some LED:s can be disabled and may be unlit.
Notes:
•
•
•
•
A network DHCP server is optional.
The AXIS 210/210A/211/211A has the default IP address 192.168.0.90
If assigning the IP address fails, check that there is no firewall blocking the operation.
For other methods of assigning or discovering the IP address of the AXIS 210/210A/211/211A, e.g. in
other operating systems, see page 10.
AXIS 210j210A/211/211A Installation Guide
(AXIS 21O/210A/2'11/211A Installation Guide
Page 9 )
AX1S lP Utility - single camera/small installation
AX1S Camera Management - multiple cameras/large installations
AXIS IP Utility automatically discovers and displays Axis devices on your network. The
application can also be used to manually assign a static IF address.
AXIS Camera Management can automatically find and set IP addresses, show connection
status, and manage firmware upgrades for multiple Axis video products.
Note that the computer running AXIS IP Utility must be on the same network segment
(physical subnet) as the AXIS 21O/21OA/211/211A.
lPAddte-S5
AXI5211A-00408C718B17
192,168.0.90
A:,J5216FD-0040,SC18298A
fe-80:0:0:0:240:Bcff:feI8:298,~
Automatic discovery
1. Check that the AXIS 21O/21OA/211/211A is connected to the network and that power has
been applied.
2. Start AXIS IP Utility.
When the camera appears in the window, double-click it to open its home page.
4. See page 10 for instructions on how to assign the password.
3.
Assign the lP address manually
Automatic discovery
1. Check that the camera is connected to the network and that power has been applied.
2. Start AXIS Camera Management. When the AXIS 21O/21OA/211/211A appears in the
window, double-click it to open the camera's home page.
3. See page 10 for instructions on how to set the password.
1. Acquire an unused IF address on the same network segment as your computer.
Set the lP address in multiple devices
2. Click the button ~ Assign new IP address using serial number and enter the serial
number and IP address for the AXIS 21O/21OA/211/211A. The serial number is located on
the product label.
3. Click the Assign button and follow the instructions.
4. Click the Home Page button to access the camera's web pages.
5. See page 10 for instructions on how to set the password.
AXIS Camera Management speeds up the process of assigning IP addresses to multiple
devices, by suggesting IP addresses from a specified range.
Select the devices you wish to configure (different models can be selected) and click the
Assign IP button.
2. Select Obtain IP addresses automatically (DHCP), click the Update button and the
program will search in the specified range and suggest an IP address for each device.
-orEnter the range of IF addresses, the subnet mask and default router that devices can use
and click the Update button.
1.
-----------~---_._---
AXIS 210!210A!211!211A Installation Guide
Page 10
( AXIS 210!210A!211!211A Installation Guide
Page 11 )
Adjust the image and focus
Set the password
When accessing the AXIS 21O/21OA/2ll/21IA
for the first time, the 'Configure Root
Password' dialog will be displayed.
1. Enter a password and then re-enter it, to
confirm the spelling. Click OK.
To focus the AXIS 21O/21OA,
unscrew the focus puller on
the lens. Adjust the focus as
required. Re-tighten the focus
puller.
~,1<!S:~.,
Configure Root Password
Th~ pH'''Q,d
b~lc,~ th~
fe' \h~ pre"o,-,'Igured .,dmir,i,tr.to, root m~"t be ,h.nged
pro<!llct ,'" b"- l1Hd
2. Enter the user name root in the dialog.
Note: The default administrator user name
,root cannot be deleted.
To focus the AXIS 211/211A follow the instmctions below.
1. From the Basic Configura-
3. Enter the password as set above, and click OK. Ifthe password is lost, the AXIS 210/
21OA/2ll/2llA must be reset to the factory default settings. See page 17.
4. If required, click Yes to install AMC (AxIS Media Control), which allows viewing of the
video stream in Internet Explorer. You will need administrator rights on the computer to
do this.The Live View page of the AXIS 21O/21OA/2ll/2llA is displayed, with links to the
Setup tools, which allow you to customize the camera.
2.
3.
Setup - Provides all the tools for configuring
the camera to requirements,
AXIS 211 Netvv'ork Camera
Focus pu Iler -----;===:I~=-_~
\
Live View I Setup
I Help
~H"P D;,pl,~
-
online help on all
aspects of using
the camera.
4.
5.
Zoom puller
tion page in the setup
(Tele/wide)
tools, open the Focus
Focus puller
adjustment page.
Set the DC-Iris to Disabled
and click Save.
Unscrew the zoom puller
on the lens by turning it
anti-clockwise. Adjust the
zoom setting as required.
Re-tighten the zoom puller.
Unscrew the focus puller on the lens. Adjust the focus as required. Re-tighten the focus
puller.
From the Focus adjustment page, set the DC-Iris to Enabled and click Save.
Note: The DC-Iris should always be disabled while focusing the camera. This opens the
iris to its maximum, which gives the smallest depth of field and thus the best
conditions for correct focusing. When the focus is set with this method it will
then be maintained in any light conditions.
Accessing the AX1S 210/21 OA/211 /211 A from the lnternet
Once installed, your AXIS 21O/21OA/2ll/2IIA is accessible on your local network (LAN). To
access the camera from the Internet, network routers must be configured to allow incoming
traffic, which is usually done on a specific port. Please refer to the documentation for your
router for filliher instmctions. For more information on this and other topics, visit the Axis
Support Web at www.axis.com/techsup
Page 12
AXIS 21O/210A/211/2'11A Installation Guide
Language interface
Pa2~
( __
A_X_IS_2_1_0_/_21_0_A_/_2_1_1/_2_1_1A_ln_s_ta_I_la_ti_ot_l_G_u_id_e
Other methods of assigning the lP address
After you have installed the Network Camera, you can download and install a language
module to change the camera's web interface to a language other than English:
The table below shows the other methods available for assigning or discovering the IP
address. All methods are enabled by default, and all can be disabled.
1. Go to Setup> Language.
2. Download the desired language from www.axis.com/techsup/ and save it temporarily to
your computer.
When enabled on your computer, the camera is automatically
detected and added to "My Network Places."
3. Click the Browse button and locate the language file.
4. Click Upload Language. The language you uploaded will appear under Select Language.
5. Select the language you want to use with your Axis camera, and click Save.
MAC OSX
(10.4 or later)
Applicable to browsers with support for Bonjour. Navigate to the
Bonjour bookmark in your browser (e.g. Safari) and click on the
link to access the camera's web pages.
All
A free service from Axis that allows you to quickly and simply
install your camera. Requires an Internet connection with no
HTIP proxy. See www.axiscam.net for more information.
All
See below. The command must be issued within 2 minutes of
connecting power to the camera.
Live View I Setup I Help
~
Basic Configuration
• Video
image
Get a language file from ,,'/ww.axls.cQm/techsup/
~
Audio
} Live
Vh~\}J
Upload Language
Contig
select language file to uplo<:idl
L~=""--J and dick [ Upload Language
To view the admin pages for the network DHCP server, please see
the server's own documentation.
I
Select language
~.
Event ConfigUf'ation
}- Systern Options
language
About
~English
Set the lP address with ARP!Ping
1. Acquire an IF address on the same network segment your computer is connected to.
2. Locate the serial number (S/N) on the AXIS 21O/21OA/211/211A label.
3. Open a command prompt on your computer and enter the following commands:
Windows syntax
Windows example
arp -s <IP Address> <Serial Number>
ping -1 408 -t <IP Address>
arp -s 192.168.0.125 00-40-8c-18-10-00
ping -1 408 -t 192.168.0.125
UNIX/Linux/Mac syntax
UNIX/Linux/Mac example
arp -s <IP Address> <Serial Number> temp
ping -s 408 <IP Address>
arp -s 192.168.0.125 00:40:8c:18:10:00
temp
ping -s 408 192.168.0.125
4. Check that the network cable is connected to the camera and then start/restart the
camera, by disconnecting and reconnecting power.
5. Close the command prompt when you see 'Reply from 192.168.0.125: ...' or similar.
6. In your browser, type in http://<IP address> in the Location/Address field and press Enter
on your keyboard.
Notes:
• To open a command prompt in Windows: from the Start menu, select Run ... and type cmd. Click OK.
• To use the ARP command on a Mac OS X, use the Terminal utility in Application> Utilities.
Page 14
AXIS 210/210A/211/211A Installation Guide
Unit connectors
Ne,nvork co~nector.- RJ-45 Ethernet connector. Supports Power over Ethernet. Using
ShIelded TWIsted PaIr (STP) cables is recommended.
Page 15
AXIS 210/210A/211/211A Installation Guide
I/O terminal connector - Used in applications for e.g. motion detection, event triggering,
time lapse recording, alarm notifications, etc. It provides the interface to:
..
Power connector - Mini DC connector. 7-20V DC, max 5W.
AUddiO in - 3.5mm i~put for a mono microphone, or a line-in mono signal (left channel is
use rrom a stereo Signal).
..
Audio o~t - Audio ou:rut (line level) that can be connected to a public address (PA) system
or an active speaker wIth a built-in amplifier. A pair of headphones can also be attached A
stereo connector must be used for the audio out.
.
..
D
1 transistor output - For connecting external devices such as relays and LEDs.
Connected devices can be activated by AXIS VAPIX API, output buttons on the
Live View page or by an Event Type. The output will show as active (shown
under Event Configuration> Port Status) if the alarm device is activated.
1 digital input - An alarm input for connecting devices that can toggle between
an open and closed circuit, for example: PIRs, door/window contacts, glass break
detectors, etc. When a signal is received the state changes and the input becomes
active (shown under Event Configuration> Port StahIs).
Auxiliary power and GND.
D
D
Pin 4
D
Pin 2
Pin 1
Pin 3
Function
Pin number
Notes
Specifications
Transistor
Output
4
Max load = SOmA
Max voltage = 24V DC
(to the transistor)
Digital Input
3
Uses an open-collector NPN transistor with
the emitter connected to the GND pin. If used
with an external relay, a diode must be connected in parallel with the load, for protection against voltage transients.
Connect to GND to activate, or leave floating
(or unconnected) to deactivate.
7 - 20 V DC
Power
GND
2
1
Can be used to power auxiliary equipment.
Must not be exposed to
voltages greater than
lOV DC
Max load = SOmA
Page 16
AXIS 210!210A!211!21 'IA Installation Guide
AXIS 21O!210A!211!211A Installation Guide
Page 17
Resetting to the Factory Default Settings
Connection diagram
This will reset all parameters, including the IP address, to the factory default settings:
Switch
Mode
Power
Supply
33V
=~
+
=;=:
1. Disconnect power from the camera.
2. Press and hold the Control button and reconnect power.
PS-K 9W
3. Keep the Control button pressed until the Power indicator flashes amber (this may take
up to 15 seconds).
2
e,g" doorbell
GND
1
3
,
,,
,
,
,
;:"
,,
,
,
L __
4
4. Release the Control button. When the Power indicator displays green (which can take up
to 1 minute) the process is complete and the camera has been reset.
5. Re-assign the IP address, using one of the methods described in this document.
It is also possible to reset parameters to the original factory default settings via the web
interface. For more information, please see the online help or the user's manual.
Further information
The user's manual is available from the Axis Web site at www.axis.com or from the Axis
Network Video Product CD supplied with this product.
Tip!
Visit www.axis.com/techsup to check if there is updated firmware available for your
AXIS 21O/21OA/211/211A. To see the currently installed firmware version, see the
Basic Configuration web page in the product's Setup tools.
LED indicators
LED
Network
Status
Power
Color
Indication
Green
Steady for connection to a 100 Mbit/s network, Flashes for network activity.
Amber
Steady for connection to 10 Mbit/s network, Flashes for network activity.
Unlit
No network connection,
Green
Steady green for normal operation.
Note: The Status LED can be configured to be unlit during normal operation, or to
flash only when the camera is accessed. To configure, go to Setup> System Options
> LED settings. See the online help files for more information.
Amber
Steady during startup, during reset to factory default or when restoring settings.
Red
Slow flash for failed upgrade.
Green
Normal operation.
Amber
Flashes green/amber during firmware upgrade.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement