VANGUARD 1X
120V
PACKING LIST
1 - Vanguard 1X unit
1 - Power Cord
1 - Hose Assembly
IMPORTANT SERVICE INFORMATION:
SAVE SHIPPING BOX AND FOAM FOR FUTURE
SERVICE. SHIPPING WITHOUT PROPER FOAM
MAY CAUSE DAMAGE TO UNIT
ASSEMBLY INSTRUCTIONS
1. Remove the unit and other parts from the box. Check against the packing list.
2. Plug the removable power cord into the socket labeled “POWER” on the top of the unit. Plug the
other end into a standard wall socket. Try the unit by turning the switch to the “ON” position.
3. The vacuum hose supplied slips onto the vacuum connection on top of the unit and the other end
connects to the collection device desired. The ideal location for the unit is under the bench where
the user works. The hose may be shortened by removing the hose cuff from one end and carefully
cutting with a sharp knife. The hose cuff threads onto the hose with a left-hand thread. Longer hoses
and adapters are available from your dealer. We recommend that you try to keep the total length of
hose less than 6 feet between the unit and the dust collection point; longer hose will reduce suction.
MAINTENANCE
1. Filter Bag Replacement - When a noticeable drop in suction occurs with the unit or it shuts down
or the filter bag is two thirds full, replace the filter bag. DO NOT attempt to clean out the filter bag.
Replace with a new Vaniman filter bag. Change the filter bag by unscrewing the two thumb screws
on the front of the unit and pull out the front cover plate to expose the filter bag compartment.
Remove the used filter bag by sliding it off the inlet tube; the front of the cardboard reinforcement
may need to be tilted downward slightly to remove the bag easily. Check the inside of the filter bag
compartment. If dust is present please clean the compartment. Cause for residual dust may be due
to improper installation. Vacuuming the excess dust will increase the life of the unit. Changing the
filter bag regularly will save wear-and-tear on the motor. Re-order P/N VMC-A400-5
2. Installing a new filter bag- Slip the cardboard reinforcement, with rudder seal, over the inlet tube.
You may need to tilt the front of the cardboard downward and slip the back edge up past the tube
end, then rotate upward over the tube end. Carefully tuck the edges of the filter bag into the filter
bag compartment. Replace the cover plate and gently tighten the thumb screws. Only gently
pressure need be used to make the gasket seal; the vacuum pressure will draw the cover tight.
3. Circuit Breaker - The unit is protected by a circuit breaker on the right side of the unit. In the
unlikely event there is an overload condition the breaker may trip. If this happens reset the breaker
by pushing on the white button until it clicks into place.
4. Motor Protection - If the motor becomes too hot it will automatically shutoff to prevent damage. To
reset the thermal gauge, turn off or unplug the unit and allow the motor to cool down. Once it has
cooled you may turn it back on and continue use.
25799 Jefferson Ave.
Murrieta, CA 92562
1-800-VANIMAN (826-4626)
www.vaniman.com
[email protected]
10310-I-11/20 Page 1
VANGUARD 1X
120V
5. Motor Brushes - This long life motor does not have replaceable brushes. Replacement motors can
be ordered as P/N 97038.
RECOMMENDED USAGE
1. Individual work station (1½” hose) dust collection for cutting, grinding and polishing of metal,
porcelain, plastic and stone.
2. The Vanguard 1X may be used alone or in conjunction with the Large Vaniman Accumulator. The
Accumulator will trap 90 - 95% of the dust in the collection trap which will extend the life of the Filter
Bag by up to 10 times.
3. The Vanguard 1X is NOT RECOMMENDED for use with aluminum oxide abrasive blasting. Such
use will void the warranty. The fine abrasive particles will cause motor damage. Vaniman offers a
suction unit specifically designed for abrasive blasters and media. It is called the SandVac (10211).
Contact your dealer for availability.
25799 Jefferson Ave.
Murrieta, CA 92562
1-800-VANIMAN (826-4626)
www.vaniman.com
[email protected]
10310-I-11/20 Page 2
VANGUARD 1X
120V
REPLACEMENT PARTS
The following items are offered to enhance the usage of your quality Vaniman unit. These items can be
order through your supplier using the following part numbers. Please feel free to contact Vaniman Mfg.
Co. with questions regarding our products.
Number
1
2
3
4
5
6
7
8
9
10
11
12
Item Description
Red Dot Motor
Motor Mount
Gold Motor Clip
Replacement Bags 3-pack
Part Number
97038
2921
3273
VMC-A400-3
Replacement Bags 5-pack
Front Cover Thumbscrew
Power Switch ON/OFF
Power Connector
Remote Plug
Transformer
Circuit Breaker, 10Amp
Back Cover Screw 6-32 x 3/8”FHSMS
Power Cord
VMC-A400-5
1449
1497
3010
1427
1417
2807
1448A
1422
6
7
5
8
9
4
10
11
3
2
1
25799 Jefferson Ave.
Murrieta, CA 92562
1-800-VANIMAN (826-4626)
www.vaniman.com
[email protected]
10310-I-11/20 Page 3
">
