Betso S107 Quick Start Manual

S107 Cordless 22.2V Stick Vacuum Cleaner
Quick Start Guide
Safety & Warnings
Over view & Accessories
Assembly Instructions
Operation
Cleaning & Care
Specification
Troubleshooting
To reduce the risk of fire, electric shock or injury to persons or property, the following
basic safety precautions should always be followed.
Never use this appliance with a damaged cord, plug or other damaged parts.
Check if the voltage indicated on the lab corresponds with the local mains
voltage before you connect the appliance.
Always ensure the charging connector, cord and plug are dry. Never immerse
the appliance into the water or any other liquid. Do not rinse it under a tap
except for the cyclone cone, the HEPA filter and the rolling brush parts.
Always ensure that your hands are dry before removing the plug from the main
outlet. Never pull the plug out of the mains outlet by its cord.
Children should always be supervised to ensure that they do not play with this
appliance.
The appliance should not be used by adults or children who lack experience,
product knowledge or disability which might cause a hazard, unless they have
been correctly instructed.
Always keep the battery pack far from fire and flammable items.
Never use this appliance to suck liquids, glass, metal fragments and burning
things such as ashes, cigarette butts, matches and so on.
Always ensure that the dust cup and the battery pack are installed before using.
If the cord, plug and any other parts get damaged or the appliance fall into
water, please stop use and immediately unplug from the main power. Never
disassemble the main body, repair or replace any parts by yourself.
Do not use non-original parts with the unit as it may cause damage.
Accessories
Adaptor
Crevice tool
Mattress brush
Stretch brush
User's manual
The appliance is packed as separated parts. Simple assembly is required before use:
① Insert the battery pack into main body as picture shows.
You will hear a click sound when fitted.
② Connect the tube to the main body.
③ Connect the floor brush to the tube.
Lithium Batter y Charging
The battery needs to be charged when the indicator lights twinkle. The lights keep
twinkling in circles while charging and turn to a complete circle while fully charged.
Attention: Please use original charger or the lithium battery can be damaged.
Start/stop working and switch speed
Press the ON/OFF button to start and stop the machine.
Press the touch panel to switch speeds. The RED light means the highest speed in active
and the BLUE light shows the eco speed in active.
Dust cup cleaning and maintenance
Method 1: Press the dust drop button and empty the dust into a rubbish bin.
Method 2: Press the dust cup release button and take out the dust cup from the main
body as the picture below.
Take off the HEPA filter and cyclone cone, empty all the rubbish and clean it. Install them
back as the picture below after the parts have air dried.
Attention: Do not use the machine before reinstalling the HEPA filter and cyclone cone or
it may damage the unit.
Floor brush cleaning and maintenance
① Press the roll brush release button.
② Take the roll brush out.
③ Wash the roll brush and air dry it. Fix it back as the pictures below.
④ Reset the roll brush release button to the lock position.
Motor rated voltage and rated power
22.2V 200W
Floor brush rated voltage and rated power
22.2V 15W
Lithium battery
22.2V 2200mAh
Charger input
~100-240V 50/60Hz
Charger output
~27V 0.5A
Charging time
4-5 hours
Noise
≤70 dB
Rated continuous working time
10 minutes at high speed
30 minutes at low speed
Product size
348*120*220mm(main body)
Product net weight
1.43kg(main body)
Problem
Possible causes
Not working
● No power
● Brush protected or obstructed
● Charging
● Restart the machine
Weak suction/
Trash drops
down from
tube
● Dust cup is full of rubbish
● HEPA filter is full of dust
● Floor brush or electrical tube
has been clogged by hair or
large pieces of rubbish
● Clean the dust cup’s rubbish
● Clean or change the HEPA filter
● Clean the floor brush or electrical
tube’s inner rubbish
No LED light
is shown
when
charging
● Battery pack is not installed in
right position
● The adaptor’s connector is not
inserted in the charging hole
● Install the battery pack in right
position
● Push the adaptor’s connector into
the charging hole in right position
Not full
battery
after charging
● Charging time is not enough
● Battery is aging
● Charge for enough 4-5 hours
● Replace battery
Floor brush
not working
Resolutions
● Clean the floor brush and restart
the machine
● Large particles or objects
● Turn off the machine and take the
vacuumed
floor brush a little high of the
● Blanket resistant strength is too
blankets leave some space
hard and protected itself.
between floor brush and
● The brush roll is entangled by
blankets and restart and machine
hair or wire.
● Clean the brush from hair, wire or
other things
Please note
A new unit may become hot with a slight plastic odour after running the motor at high
speed for several minutes. This is normal and not a cause for concern.