Alliance Laundry Systems | NX18BVXM7 | Specifications | Alliance Laundry Systems NX18BVXM7 Specifications

Basic Installation/Operation
Washer-Extractors
Cabinet Freestanding
Coin Models
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 9002062R3
www.comlaundry.com
January 2010
Table of
Contents
Introduction.........................................................................................
Model Identification .............................................................................
2
2
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
Safety Decals ........................................................................................
Operator Safety.....................................................................................
3
3
3
5
6
Specifications and Dimensions...........................................................
7
Installation...........................................................................................
Dimensional Clearances...................................................................
Machine Foundation ........................................................................
Mounting Bolt Installation (If Required)..............................................
Removing the Transport Block.............................................................
13
13
13
14
15
Operation............................................................................................. 17
Control Panel ........................................................................................ 17
Operating Instructions .......................................................................... 18
Disposal of Unit ................................................................................... 20
© Copyright 2010, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Introduction
Model Identification
Information in this manual is applicable to these
models:
2
18
NX18BVPA6
NX18BVPA7
NX18BVQA6
NX18BVQA7
NX18BVXA6
NX18BVXA7
NX18BVXM7
SX18BVPA7
SX18BVQA7
SX18BVXA7
SX18BVXM7
30
NX30BVPA6
NX30BVPA7
NX30BVQA6
NX30BVXM7
NX30BVQA7
NX30BVXA6
NX30BVXA7
SX30BVPA7
SX30BVQA7
SX30BVXA7
SX30BVXM7
33
SX33BVPA7
SX33BVQA7
SX33BVXA7
SX33BVXM7
40
SX40BVPA7
SX40BVQA7
SX40BVXA7
SX40BVXM7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
DANGER
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
9. Do not install or store the washer where it will be
exposed to water and/or weather.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
13. Use washer only for its intended purpose,
washing textiles.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
16. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
20. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc., or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Safety Information
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004
IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance
are provided. Never allow the inspection and
maintenance space to be blocked.
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
SW025
WARNING
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
the pipe can be touched.
SW014
WARNING
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
damage.
W703
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Safety Information
Operator Safety
Do not bypass any safety devices in the machine.
WARNING
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
damage.
SW039
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Specifications and Dimensions
General Specifications
Model
18
30
33
40
Overall width
660 mm
(26 in.)
780 mm
(30.7 in.)
780 mm
(30.7 in.)
780 mm
(30.7 in.)
Overall height
1038 mm
(40.9 in.)
1202 m
(47.3 in.)
1376 mm
(54.15 in.)
1376 mm
(54.15 in.)
Overall depth
739 mm
(29.1 in.)
842 mm
(33.1 in.)
840 mm
(33.07 in.)
940 mm
(37.01 in.)
Net weight
211 kg
(465.2 lb.)
325kg
(716.5 lb.)
368 kg
(811.30 lb.)
391 kg
(862.01 lb.)
Shipping weight
233 kg
(513.7 lb.)
355 kg
(782.6 lb.)
383 kg
(844.37 lb.)
418 kg
(921.53 lb.)
Shipping volume
0.8 m3
(22.5 ft3)
1.3 m3
(34.7 ft3)
1.21 m3
(42.83 ft3)
1.3 m3
(45.98 ft3)
Cylinder diameter
530 mm
(20.9 in.)
650 mm
(25.6 in.)
680 mm
(26.77 in.)
680 mm
(26.77 in.)
Cylinder depth
330 mm
(13 in.)
400 mm
(15.76 in.)
400 mm
(15.75 in.)
500 mm
(19.69 in.)
Cylinder volume
76 l
(2.7 ft3)
132 l
(4.66 ft3)
145 l
(5.12 ft3)
181 l
(6.39 ft3)
Perforation size
3 mm
(0.12 in.)
3 mm
(0.12 in.)
3 mm
(0.12 in.)
3 mm
(0.12 in.)
Door opening size
300 mm
(11.8 in.)
300 mm
(11.8 in.)
400 mm
(15.75 in.)
400 mm
(15.75 in.)
Height of door bottom above floor
280 mm
(11 in.)
381 mm
(15 in.)
472 mm
(18.58 in.)
472 mm
(18.58 in.)
Overall Dimensions
Weight and Shipping Information
Wash Cylinder Information
Door Opening Information
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Specifications and Dimensions
General Specifications
Model
18
30
33
40
1
1
1
1
1 HP (0.75 kW)
2 HP
(1.5 kW)
2.95 HP
(2.2 kW)
2.95 HP
(2.2 kW)
10-50 RPM
10-50 RPM
10-50 RPM
10-50 RPM
85 RPM
85 RPM
85 RPM
85 RPM
250-1000 RPM
250-1000 RPM
250-1000 RPM
250-1000 RPM
0.03-0.74 Gs
0.04-0.91 Gs
0.37-0.94 Gs
0.37-0.94 Gs
19-296 Gs
23-363 Gs
24-377 Gs
24-377 Gs
Standard
Standard
Standard
Standard
9 kW
18 kW
18 kW
18 kW
Electrical heating elements
3
6
6
6
Electrical heat element size
3 kW
3 kW
3 kW
3 kW
Drive Train Information
Number of motors in drive train
Drive motor power
Cylinder Speeds
Wash/reverse speed
Distribution/drain speed
Extract speed
Centrifugal Force Data
Wash/reverse centrifugal force
Extract centrifugal force
Balance Detection
Vibration safety switch installed
Electrical Heating (International Models Only)
Total electrical heating capacity
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Specifications and Dimensions
220 mm
(8.7 in.)
H
1038 mm
(40.9 in.)
1011 mm
(39.8 in.)
365 mm
(14.4 in.)
65 mm
(2.6 in.)
530 mm (20.9 in.)
65 mm
(2.6 in.)
670 mm (26.3 in.)
660 mm (26 in.)
231 mm
(9.1 in.)
75 mm
(3 in.)
69 mm
(2.7 in.)
153 mm
(6 in.)
1
727 mm (28.6 in.)
184 mm
(7.2 in.)
139 mm
(5.5 in.)
8
2
7
3
843 mm
(33.2 in.)
4
6
809 mm
(31.9 in.)
180 mm
(7 in.)
633 mm
(27.7 in.)
5
660 mm
(26 in.)
70 mm
(2.8 in.)
CFD513N
18 MODEL
CFD513N
1
2
3
4
Hot Water Connections 19 mm (.75 in.)
Power Input
Emergency Stop Button
Ventilation Tub
5
6
7
8
Drain Outlet
Cold Water Inlet (required) 19 mm (.75 in.)
Cold Water Inlet (required) 19 mm (.75 in.)
Fill and Supply Ventilation
Figure 1
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Specifications and Dimensions
88 mm
(3.5 in.)
220 mm
(8.7 in.)
H
1202 mm
(474 in.)
1175 mm
(46.3 in.)
475 mm
(18.7 in.)
66 mm
(2.6 in.)
648 mm (25.5 in.)
66 mm
(2.6 in.)
760 mm (29.9 in.)
780 mm (30.7 in.)
82 mm
(3.2 in.)
332 mm
(13.1 in.)
267 mm
(10.5 in.)
202 mm
(8 in.)
1
2
816 mm (32.1 in.)
200 mm
(7.9 in.)
155 mm
(6.1 in.)
8
3
4
7
5
924 mm
(36.4 in.)
35 mm
(1.4 in.)
964 mm
(38 in.)
200 mm
(7.9 in.)
849 mm
(33.5 in.)
6
70 mm
(2.8 in.)
CFD514N
30 MODEL
CFD514N
1
2
3
4
Hot Water Connections 19 mm (.75 in.)
Cold Water Inlet (required) 19 mm (.75 in.)
Power Input
Emergency Stop Button
5
6
7
8
Ventilation Tub
Drain Outlet
Cold Water Inlet (required) 19 mm (.75 in.)
Fill and Supply Ventilation
Figure 2
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Specifications and Dimensions
88 mm
(3.47 in.)
220 mm
(8.66 in.)
472 mm (18.58 in.)
1376 mm (54.15 in.)
1348 mm (53.07 in.)
H
680 mm (26.77 in.)
50 mm
(1.97 in.)
50 mm
(1.97 in.)
780 mm (30.71 in.)
34 mm
(1.34 in.)
86.5 mm
(3.41 in.)
CFD537N
CFD540N
332 mm (13.05 in.)
267 mm (10.49 in.)
202 mm (7.93 in.)
105 mm (4.13 in.)
1
2
4
665 mm (26.18 in.)
733 mm (28.86 in.)
753 mm (29.65 in.)
34 mm
(1.34 in.)
CFD538N
CFD538N
3
5
6
7
35 mm
(1.38 in.)
109 mm
(4.3 in.)
185 mm (7.29 in.)
1015 mm (39.96 in.)
1141 mm (44.9 in.)
1108 mm (43.6 in.)
1066 mm (41.95 in.)
704 mm (27.7 in.)
8
9
170 mm (6.69 in.)
CFD539N
CFD539N
33 MODEL
1
2
3
4
5
Fill and Supply Ventilation
External Liquid Supply Inlets
Cold Water Inlet (Required)
Cold Water Inlet (Required)
Hot Water Inlet (Required)
6
7
8
9
Connection Clamps
Electrical Power Inputs
Ventilation Tub
Drain Valve
Figure 3
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Specifications and Dimensions
88 mm
(3.47 in.)
220 mm
(8.66 in.)
472 mm (18.58 in.)
1376 mm (54.15 in.)
1348 mm (53.07 in.)
H
680 mm (26.77 in.)
50 mm
(1.97 in.)
50 mm
(1.97 in.)
780 mm (30.71 in.)
34 mm
(1.34 in.)
86.5 mm
(3.41 in.)
CFD537N
CFD540N
332 mm (13.05 in.)
267 mm (10.49 in.)
202 mm (7.93 in.)
105 mm (4.13 in.)
1
2
4
3
765 mm (30.12 in.)
833 mm (32.8 in.)
853 mm (33.58 in.)
34 mm
(1.34 in.)
CFD538N
CFD538N
5
6
7
35 mm
(1.38 in.)
109 mm
(4.3 in.)
185 mm (7.29 in.)
1015 mm (39.96 in.)
1141 mm (44.9 in.)
1108 mm (43.6 in.)
1066 mm (41.95 in.)
704 mm (27.7 in.)
8
9
170 mm (6.69 in.)
CFD539N
CFD539N
40 MODEL
1
2
3
4
5
Fill and Supply Ventilation
External Liquid Supply Inlets
Cold Water Inlet (Required)
Cold Water Inlet (Required)
Hot Water Inlet (Required)
6
7
8
9
Connection Clamps
Electrical Power Inputs
Ventilation Tub
Drain Valve
Figure 4
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Installation
Dimensional Clearances
Machine Foundation
Table 1 shows recommended minimum clearances on
all sides of the washer-extractor.
Thoroughness of detail must be stressed with all
foundation work to ensure a stable unit installation,
eliminating possibilities of excessive vibration during
extract.
Recommended Minimum Clearances
Model
18
30
33
40
Minimum
rear
clearance
600 mm
(24 in.)
600 mm
(24 in.)
600 mm
(24 in.)
600 mm
(24 in.)
Minimum
clearance
between
machine
and wall
150 mm
(6 in.)
150 mm
(6 in.)
150 mm
(6 in.)
150 mm
(6 in.)
Minimum
clearance
between
machines
(side)
25.4 mm 25.4 mm
(1 in.)
(1 in.)
33 mm
(1.2 in.)
33 mm
(1.2 in.)
419 mm 419 mm 533 mm
Minimum
front
(16.5 in.) (16.5 in.) (21 in.)
clearance
(door swing)
533 mm
(21 in.)
CAUTION
Ensure that the machine is installed on a
level floor of sufficient strength and that
the recommended clearances for
inspection and maintenance are provided.
Never allow the inspection and
maintenance space to be blocked.
W488
Table 1
The washer-extractor must be placed on a smooth
level surface so that the entire base of the machine is
supported and rests on the mounting surface.
The standard installation does not require anchoring
unless mandated by state or local codes.
Kinetic energy of the cylinder and dynamic loads on
the floor or foundation are shown in Table 2.
Table 2 can be used as a reference when designing
floors and foundations.
Floor Load Data
Model
18
30
33
40
1386 N/m 2592 N/m 2736 N/m 4105 N/m
Kinetic
energy of
the
cylinder
Dynamic
bottom
load
700 N/16
Hz
1000 N/
16 Hz
1200 N/
16 Hz
1200 N/
16 Hz
Table 2
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Installation
Mounting Bolt Installation
(If Required)
3. Put bolts through the machine in the anchors and
fasten them. For 18 and 30 models, the diameter
of the bolt must be minimum 1/2-13 or 12 mm.
For 33 and 40 models, the diameter of the bolt
must be minimum 5/8-11 or 16 mm.
1
4. To level machine, fill the spaces between the
machine base and floor with machinery grout.
Grout completely under all frame members.
Remove front and rear panels to gain access to all
frame members. Force grout under the machine
base until all voids are filled.
2
3
5. Remove the spacers carefully, allowing the
machine to settle into the wet grout.
6. Position washers and locknuts on machinery
anchor bolts and finger tighten to machine base.
152 mm
(6 in.)
7. After the grout is completely dry, tighten the
locknuts by even increments – one after the
other – until all are tightened evenly and the
machine is fastened securely to the floor.
4
CFS485N
CFS485N
1
2
3
4
Base Frame
Bolt
Washer
Anchor Bolt/Plug
Figure 5
After the concrete has cured and the anchors are
installed, proceed as follows:
1. Place the washer-extractor adjacent to the
foundation. Do not attempt to move it by pushing
on the sides. Always insert a pry bar or other
device under the bottom of the frame of the
washer-extractor to move it.
2. Place the washer-extractor carefully over the
anchors.
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Installation
Removing the Transport Block
4. For 18 and 30 models, remove the panel braces.
Refer to Figure 7.
WARNING
The machine must never be activated
before removing the transport block.
W618
To prevent damage during transportation, machine has
been equipped with a transport block. To remove,
proceed as follows:
1. Place machine on level ground.
2. Remove service panels and back panel.
3. At rear of machine, lift at bottom of motor and
remove transport block if present. Refer to
Figure 6.
CFD34N
1
18 AND 30 MODELS
CFD34N
1
Panel Braces
Figure 7
5. For 33 and 40 models, remove the transport
brackets. Refer to Figure 8.
FRONT
1
1
1
CFD26N
CFD26N
1
Transport Block (Remove)
Figure 6
REAR
IMPORTANT: Do NOT lift motor by the pulley.
1
1
33 AND 40 MODELS
CFD543N
1
Transport Brackets
Figure 8
6. Replace all panels removed.
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Installation
Electrical Specifications
Voltage Designation
Full Load Amps
Circuit Breaker
AWG/mm2
kW
50/60
3
3+N+PE
Not available
21
30
10/6.0
9
Q
200-240
50/60
3
3+PE
Not available
27
30
10/6.0
9
X
200-240
50/60
1/3
2/3+PE
P
380-415
50/60
3
3+N+PE
Not available
36
40
8/10.0
18
Q
200-240
50/60
3
3+PE
Not available
49
60
6/16.0
18
X
200-240
50/60
1/3
2/3+PE
13
20
12/4.0
1.5
P
380-415
50/60
3
3+N+PE
18
20
12/4.0
1.5
44
50
8/10.0
18
Q
200-240
50/60
3
3+PE
18
20
12/4.0
1.5
63
70
4/25.0
18
X
200-240
50/60
1/3
2/3+PE
18
20
12/4.0
1.5
P
380-415
50/60
3
3+N+PE
18
20
12/4.0
1.5
44
50
8/10.0
18
Q
200-240
50/60
3
3+PE
18
20
12/4.0
1.5
63
70
4/25.0
18
X
200-240
50/60
1/3
2/3+PE
18
20
12/4.0
1.5
12
16
14/2.5
kW
380-415
AWG/mm2
P
Circuit Breaker
Wire
Full Load Amps
Phase
40
Cycle
33
Voltage
30
Electric Heat
Code
Model
18
Standard
0.75
Not available
Not available
Not available
Not available
Table 3
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Operation
Control Panel
12
1
2
12
2
1
5
WASH
ADD
BLEACH
RINSE
SPIN
NORMAL
PERM PRESS
HOT
WARM
NORMAL
PERM PRESS
WARM
COLD
QUICK WASH
QUICK WASH
6
95C
95C
6
7
60C
60C
7
40C
40C
START
DOOR
HOT
HOT
COLD
4
DOMESTIC MODELS
10
30C
9
11
9
3
4
10CHM488R
INTERNATIONAL MODELS
CHM482R
CHM482R
1
2
3
4
5
6
8
<
3
DELICATE
<
11
8
WARM
HEAVY SOIL
5
Cycle 1
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 6
CHM488R
7
8
9
10
11
12
Cycle 7
Cycle 8
Down Edit/Change keypad
Up Edit/Change keypad
Start/Enter keypad
Display
Figure 9
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Operation
Operating Instructions
1. Turn on main power source (circuit breaker).
NORMAL
WASH
2. Pull the door handle towards you to open the
door. Some models may have a door handle with
a button that must be pressed.
3. Load to capacity whenever possible. DO NOT
OVERLOAD. Refer to Figure 10.
NOTE: Underloading can cause out-of-balance
conditions that can shorten machine life.
ADD
BLEACH
RINSE
SPIN
DOOR
PERM PRESS
HOT
WARM
NORMAL
PERM PRESS
WARM
COLD
QUICK WASH
QUICK WASH
START
HOT
WARM
HEAVY SOIL
DELICATE
HOT
COLD
DOMESTIC MODELS
CHM482R
CHM482R
95C
95C
60C
60C
40C
40C
30C
<
<
INTERNATIONAL MODELS
CHM488R
CHM488R
CFD53N
CFD53N
Figure 10
4. Close door by pushing door handle towards
machine.
Figure 11
6. If desired, select a different cycle at this point
before satisfying vend. The LED indicator for
that cycle will light.
5. The default wash cycle will display.
NOTE: Perm Press Cold is the default cycle for
coin models if none is selected.
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Operation
7. Add liquid and/or powder supplies to supply
dispenser. Refer to Figure 12.
a. Add detergent to compartment 1.
8. Add coins to machine. As each coin is added, the
vend counts down to the amount remaining.
Refer to Figure 12.
9. When applicable, add bleach to compartment 2
when the ADD BLEACH LED is lit.
b. Add softener to compartment 3.
10. Press the desired wash cycle keypad.
11. Press the START keypad and the active cycle
remains the chosen wash cycle.
3
12. When cycle is complete, display shows “donE”.
1
2
B157R
B157R
1
2
3
Detergent
Bleach
Softener
Figure 12
9002062
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Disposal of Unit
This appliance is marked according to the European
directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Refer to Figure 13. Instead it shall
be handed over to the applicable collection point for
the recycling of electrical and electronic equipment.
Ensuring this product is disposed of correctly will help
prevent potential negative consequences for the
environment and human health which could otherwise
be caused by inappropriate waste handling of this
product. The recycling of materials will help to
conserve natural resources. For more detailed
information about recycling of this product, please
contact the local city office, household waste disposal
service, or the source from which the product was
purchased.
20
MIX1N
Figure 13
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9002062
Download PDF