SLLU218

SLLU218
User's Guide
SLLU218 – June 2015
ISO5851 Evaluation Module
The manual describes the ISO5851 Evaluation Module (EVM). The ISO5851 EVM allows designers to
evaluate device AC and DC performance with a pre-populated 1-nF load or with a user-installed IGBT in
either of the standard TO-247 or TO-220 packages.
Warning: Note that although these devices provide galvanic isolation of up
to 5700-V, the EVM cannot be used for isolation voltage testing. Voltage
exceeding the EVM’s ratings (VCC1 > 5.5-V, VCC2 – VEE2 > 30-V, or IGBT
Collector-Emitter Voltage VCE > 50-V) can damage the EVM resulting in
personal injury.
1
2
3
4
Contents
Overview ...................................................................................................................... 2
EVM Setup and Precautions ............................................................................................... 3
2.1
Power Supply Connections ........................................................................................ 3
2.2
Signal Connections ................................................................................................. 4
Example Measurements .................................................................................................... 5
Printed-Circuit Board ........................................................................................................ 8
4.1
ISO5851 Operation ................................................................................................. 8
4.2
ISO5851 EVM Bill of Materials .................................................................................. 11
List of Figures
1
ISO5851 EVM Power Supply Schematic ................................................................................. 3
2
Output Power Supply for Unipolar (Left) or Bipolar (Right) Operation ................................................ 3
3
ISO5851 EVM Signal Path Schematic .................................................................................... 4
4
ISO5851 EVM Input and Output With Unipolar Output Supply ........................................................ 5
5
ISO5851 EVM Input and Output With Bipolar Output Supply (VCC2 = 15-V, VEE2 = –8-V) .......................... 6
6
ISO5851 EVM DESAT and Reset with Unipolar Output Supply....................................................... 6
7
ISO5851 EVM DESAT and Reset with Bipolar Output Supply ........................................................ 7
8
ISO5851 EVM
9
To have different Turn-on and Turn-off ................................................................................... 9
...............................................................................................................
8
List of Tables
1
Test Points .................................................................................................................. 10
2
Bill of Materials
.............................................................................................................
11
All trademarks are the property of their respective owners.
SLLU218 – June 2015
Submit Documentation Feedback
ISO5851 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
1
Overview
1
www.ti.com
Overview
The ISO5851 is a 5.7-kVRMS, reinforced isolated, IGBT gate driver with 2.5-A source and 5-A sink currents.
The primary side operates from a single 3-V to 5.5-V supply. The output side allows for a supply range
from minimum 15-V to maximum 30-V. Two complementary CMOS inputs control the output state of the
gate driver. The short propagation time assures accurate control of the output stage.
An internal desaturation detection recognizes when the IGBT is in an overload condition. Upon a
desaturation detect, the gate driver output is driven low to VEE2 potential, turning the IGBT immediately off.
When desaturation is active, a fault signal is sent across the isolation barrier pulling the FLT output at the
primary side low and blocking the isolator input. The FLT output condition is latched and can be reset
through a low-active pulse at the RST input.
When the IGBT is turned off during normal operation with bipolar output supply, the output is hard clamp
to VEE2. If the output supply is unipolar, an active Miller clamp can be used, allowing Miller current to sink
across a low impedance path preventing IGBT to dynamically turned on during high voltage transient
conditions.
The readiness for the gate driver to be operated is under the control of two undervoltage-lockout circuits
monitoring the primary and secondary supplies. If either side have insufficient supply, the RDY output
goes low, otherwise the output is high.
2
ISO5851 Evaluation Module
SLLU218 – June 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
EVM Setup and Precautions
www.ti.com
2
EVM Setup and Precautions
2.1
Power Supply Connections
Figure 1 illustrates the EVM power supply schematic.
Figure 1. ISO5851 EVM Power Supply Schematic
The primary side of the EVM (VCC1) operates from a single 3-V to 5.5-V power supply and connected via
TB3. Test point (TP8) is available for monitoring the primary power supply.
The EVM provides connections for evaluating the output side (VCC2, VEE2) with either a bipolar or unipolar
power supply, from a minimum 15-V to maximum 30-V. For unipolar operation, connect VEE2 to GND2
through a wire-bridge between pin 2 and pin 3 of TB2, as shown in Figure 2. VCC2 and VEE2 can be
monitored via TP17 and TP19, respectively.
PSU
VCC2
VCC2
VEE2
VCC2
GND2
VEE2
VCC2
GND2
TB2
VEE2
TB2
PSU
Figure 2. Output Power Supply for Unipolar (Left) or Bipolar (Right) Operation
SLLU218 – June 2015
Submit Documentation Feedback
ISO5851 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
3
EVM Setup and Precautions
2.2
www.ti.com
Signal Connections
Figure 3 illustrates the ISO5851 EVM signal path schematic.
VEE2
VCC1
VCC1
VCC1
Figure 3. ISO5851 EVM Signal Path Schematic
2.2.1
I/O Connections
Figure 3 shows the signal path schematic of the EVM. JMP1 allows for stimulus or monitoring of the
device I/O pins IN+, IN-, RDY, FLT, and RST. Test points 1, 2, 3, 4, and 5 provide additional access to the
I/O pins. The EVM comes populated with 10-kΩ pullup resistors (R1, R2) on the RDY and FLT pins, as
well as 220-pF capacitors (C4, C5) to GND1 for noise filtering.
2.2.2
Output and Loading
The EVM comes populated with a 1-nF load (C12) on the output side. The output can be monitored
directly via TP12. A 10:1 resistor-divider network is provided for monitoring the output with a low-voltage
probe via TP20. The divider circuit can be disconnected from the output by removing the shunt on JMP5.
10-Ω gate resistors (R3, R12) control the rise and fall times of the output. These resistors can be modified
by the user to alter the turn-on and turn-off characteristics of the output.
The EVM also allows for evaluation of the device with an IGBT load in either of the standard TO-247 or
TO-220 footprints. During evaluation with an IGBT load, the pre-installed capacitive load (C12) can be
disconnected from the output by removing the shunt on JMP2.
The EVM provides an additional connection (P2) for applying an external power supply to the IGBT
Collector. The EVM is not intended for high voltage testing and the voltage applied to P2 should be limited
to 50-V DC.
When evaluating the device with an IGBT load using P2, the components D1, D2, R7, and C13 should be
populated with their default values, specified in Figure 3. Additionally, ensure that the DESAT pin is not
connected to GND2 when driving an IGBT load using P2, either by removing R8, or verifying that all
jumpers are removed from JMP3.
4
ISO5851 Evaluation Module
SLLU218 – June 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Example Measurements
www.ti.com
2.2.3
DESAT
The EVM comes populated with a 220-pF DESAT capacitance. Pin1 on JMP3 can be used to apply a
signal directly to the DESAT pin.
For evaluation with the default 1-nF load, when actual IGBT is not connected as load, the desaturation
function should be disabled by connecting the DESAT pin to GND2 by shunting pin 1 to pin 2 on JMP3.
2.2.4
CLAMP
By default, the CLAMP pin is connected to the output via a 0-Ω resistor (R6). The CLAMP feature can be
disabled by removing R6. CLAMP can be monitored via TP14, and a signal can be applied directly to the
CLAMP pin via JMP4.
3
Example Measurements
Figure 4 illustrates measurements performed under the default EVM configuration. For these
measurements, VIN- is connected to GND1.
Figure 4. ISO5851 EVM Input and Output With Unipolar Output Supply
Figure 4 shows the input and output of the ISO5851 EVM for a 100-kHz clock with RG = 10 Ω (R3) and
R12 = 10 Ω and a unipolar output supply (VCC2 = 15-V, VEE2 = GND2). The output is measured at TP12.
SLLU218 – June 2015
Submit Documentation Feedback
ISO5851 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
5
Example Measurements
www.ti.com
Figure 5 shows the input and output of the ISO5851 EVM for a 100-kHz clock with RG = 10 Ω (R3) and
R12 = 10 Ω and a bipolar output supply (VCC2 = 15-V, VEE2 = –8-V).
Figure 5. ISO5851 EVM Input and Output With Bipolar Output Supply (V CC2 = 15-V, VEE2 = –8-V)
Figure 6 with Unipolar Output Supply and Figure 7 with Bipolar Output Supply, shows the functionality of
the DESAT, FLT, and RST pins. IN+ is set to 5-VDC, and an 10-µs pulse is applied to RST. On the rising
edge of RST, the fault is cleared and the DESAT capacitor begins to charge. As the DESAT pin reaches
the DESAT threshold voltage, a fault is triggered on FLT, and the output goes into active turn-off. RST
must be toggled low, then high to reset the device, and the cycle begins again.
Figure 6. ISO5851 EVM DESAT and Reset with Unipolar Output Supply
6
ISO5851 Evaluation Module
SLLU218 – June 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Example Measurements
www.ti.com
Figure 7. ISO5851 EVM DESAT and Reset with Bipolar Output Supply
SLLU218 – June 2015
Submit Documentation Feedback
ISO5851 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
7
Printed-Circuit Board
4
www.ti.com
Printed-Circuit Board
The ISO5851 is an isolated gate driver with several important features. The printed-circuit board
(PCB)/EVM, as shown in Figure 8 ISO5851 EVM, has been designed to support the ISO5851 device and
to allow the user to evaluate its basic operation and features. The left side of the PCB contains the
interface to the input, control, and status functions of the integrated circuit (IC). The right side of the PCB
has been designed to interface to an IGBT. No electrical connections exist between the right and left sides
of the PCB.
Figure 8. ISO5851 EVM
Refer to the ISO5851EVM schematic shown in Figure 3 and the bill of materials given in Table 2, to
become familiar with the PCB components and layout.
The following table pertains to the labels on the EVM board (Figure 8):
4.1
Given
Read As
VCC1
VCC1
VCC2
VCC2
VEE2
VEE2
VCE
VCE
VIN+
IN+
VIN–
IN–
/FAULT
FLT
ISO5851 Operation
4.1.1
Left-Side Operation: DC Power, Control, and Status
4.1.1.1
DC Input Power
The left side of the ISO5851 (and therefore the PCB) can be operated using either a +3-V (±10%) to +5.5V (±10%) dc power supply. As the current requirement is extremely low, the user can choose to operate
the ISO5851 EVM by battery. The dc power supply must be connected to the TB3 terminal having VCC1
(+5.5-V DC) and GND1 (+5.5-V DC return).
8
ISO5851 Evaluation Module
SLLU218 – June 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Printed-Circuit Board
www.ti.com
4.1.1.2
Control and Status
The interface to the device is via the JMP1 header. It contains the IN+ and IN– inputs, the device RST,
RDY, and FLT indicator output. The JMP1 header allows easy connections to test equipment using
standard clip leads. Each of the five signals also has a test point for additional connections. These are test
points TP1–TP5.
4.1.2
Right-Side Operation
4.1.2.1
DC Output Power
Power is provided to VCC2 on the right side of the device at TB2 terminal as shown in Figure 2. The dc
supply must be able to provide a bias voltage over the range of +15-V DC to +30-V DC. As the current
requirement is extremely low, the user can choose to operate the ISO5851 EVM by battery. If a negative
gate drive is required, a dc supply (or battery) must be connected across VEE2 at the TB3 terminal as
shown in Figure 2. The voltage range must be between 0-V and 15-V DC.
4.1.2.2
DESAT – JMP3
One of the features of the ISO5851 is the IGBT desaturation protection. JMP3 provides access to the
DESAT pin. It is a 3-pin male header, and installing a shorting jumper between pin 1 and pin 2 on JMP3
disables the DESAT function.
4.1.2.3
Load
As shipped, the ISO5851EVM does not have an IGBT installed. The user can evaluate device operation
using a capacitive load of 1nF provided on EVM or capacitive load can be removed and IGBT can be
connected onto the board. Most IGBTs are available in the standard TO-247 or TO-220 package. The
PCB has provisions to solder an IGBT directly onto the board.
4.1.2.3.1
No IGBT Installed – JMP2
When using the capacitive load, the user must install a jumper short onto JMP2. It connects a 1-nF
capacitor (C12) to the OUT pin. The capacitive consists of the 10-Ω gate resistor (R3) and the 1-nF
capacitor (C12).
4.1.2.3.2
IGBT Installed – REMOVE JMP2
If the user chooses to install an IGBT, JMP2 must be left open with no shorting jumper installed. The PCB
has been designed with plated-through holes (or vias) as Q1 and Q2 shown on the schematic for IGBT
connections.
4.1.2.4
Turn-on and Turn-off Adjust
The PCB contains10-Ω gate resistor (R3), D4 diode, and 10-Ω R12 resistor. It allows the user to evaluate
device operation with different turn-on and turn-off characteristics. It is shown in Figure 9.
To Change
Turnon and Turnoff
by R3 and R12
D4
R12
R3
10 :
10 :
OUT
R12
D4
Turnon/Turnoff
is Same
(As Shipped)
R3
OUT
10 :
Figure 9. To have different Turn-on and Turn-off
SLLU218 – June 2015
Submit Documentation Feedback
ISO5851 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
9
Printed-Circuit Board
4.1.3
www.ti.com
Test Points
Test points have been provided for ready access to signal monitoring and are listed in Table 1.
Table 1. Test Points
10
Test Points
I/O
TP1
Input
IN+
Function
(Side 1)
TP2
Input
IN–
(Side 1)
TP3
Output
RDY
(Side 1)
TP4
Output
FLT
(Side 1)
TP5
Input
RST
(Side 1)
TP6
Ground
GND1
(Side 1)
TP7
Ground
GND1
(Side 1)
TP8
Supply
VCC1
(Side 1)
TP9
Ground
GND1
(Side 1)
TP10
Input
COLLECTOR VOLTAGE
(Side 2)
TP11
Input
EMITTER VOLTAGE
(Side 2)
TP12
Output
GATE VOLTAGE
(Side 2)
TP13
Input
DESAT
(Side 2)
TP14
Input
CLAMP
(Side 2)
TP15
Ground
GND2
(Side 2)
TP16
Ground
GND2
(Side 2)
TP17
Supply
VCC2
(Side 2)
TP18
Ground
GND2
(Side 2)
TP19
Supply
VEE2
(Side 2)
TP20
Output
OUT
(Side 2)
P1
Ground
GND2
(Side 2)
P2
Input
COLLECTOR VOLTAGE
(Side 2)
ISO5851 Evaluation Module
SLLU218 – June 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Printed-Circuit Board
www.ti.com
4.2
ISO5851 EVM Bill of Materials
The ISO5851 EVM bill of materials is shown in Table 2.
Table 2. Bill of Materials
Item
QTY
Reference
Part
Manufacturer
Manufacturer Part Number
1
1
C1
DNI
DNI
DNI
2
1
C2
1 µF
AVX Corporation
TPSA105K020R3000
3
1
C3
0.1 µF
Kemet Electronic Components
C0805C104J5RACTU
4
2
C4,C5
220 pF
Vankel
C0805COG101-221JNE
5
2
C6,C9
22 µF
AVX Corporation
TAJV226K050RNJ
6
2
C7,C10
4.7 µF
Kemet Electronic Components
C1210X475K5RACTU
7
4
C8,C11,C14,C15
1 µF
Murata Electronics North America GRM21BR71H105KA12L
8
1
C12
1 nF
Murata Electronics North America GRM2195C2A102JA01D
9
1
C13
220 pF
Venkel
C0805COG101-221JNE
10
1
D1
UF4007
Fairchild Semiconductor
UF4007
11
1
D2
BAT165
Infineon Technologies
BAT 165 E6327
12
1
D3
MURS160T3G
ON Semiconductor
MURS160T3G
13
1
D4
BAT165
Infineon Technologies
BAT 165 E6327
16
1
JMP1
Header 5x2
Samtec Inc
HTSW-105-07-G-D
17
2
JMP2,JMP5
HDR_THVT_1x2
Samtec Inc
HTSW-102-07-G-S
18
2
JMP3,JMP4
Header 3x1
Samtec Inc
HTSW-103-07-G-S
19
1
P1
GND2
Emerson Network Power
108-0740-001
20
1
P2
COLLECTOR (50-V DC MAX)
Emerson Network Power
108-0740-001
21
2
Q1, Q2
IGBT
DNI
DNI
22
2
R1,R2
10 kΩ
Vishay Dale
CRCW080510K0FKEA-
23
2
R3, R12
10
Vishay Dale
CRCW120610R0FKEA
23b
1
R4
DNI
DNI
DNI
24
1
R5
10
Vishay/Dale
CRCW120610R0FKEA
25
3
R6,R8,R9
0
Vishay Dale
CRCW12060000Z0EA-
26
1
R7
1 kΩ
Panasonic - ECG
ERJ-8ENF1001V
27
1
R10
9 kΩ
Yageo
RC1206FR-079K09L
28
1
R11
1 kΩ
Panasonic - ECG
ERJ-8ENF1001V
29
1
TB2
3PIN_TERMINAL_BLOCK
TE Connectivity
282834-3
30
1
TB3
2PIN_TERMINAL_BLOCK
TE Connectivity
282834-2
32
1
U1
16 PIN DEVICE
Texas Instruments
ISO5851DW
33
20
TP1 through TP20
Color: Red for Power, Black for Ground
and Blue for Signal
34
4
Standoff/spacers
1 inch
Note: C6, C7, C8, C9, C10, C11, C12, C13, C14, and C15 are rated for > 50-V
Jumpers (default):
a. Pins 1 and 2 of JMP2 are connected with a jumper.
b. Pins 1 and 2 of JMP5 are connected with a jumper.
c. No jumper on any pins of JMP3 & JMP4.
d. Pin 3 and 4 of JMP1 are connected with a jumper and rest pins of JMP1 are kept open
SLLU218 – June 2015
Submit Documentation Feedback
ISO5851 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
11
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising