Alliance Laundry Systems | CCN040KNF | Specifications | Alliance Laundry Systems CCN040KNF Specifications

Cabinet Hardmount
Design 2 and 3 Models
Refer to Page 8 for Model Identification
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com
Installation/Operation/Maintenance
Washer-Extractors
CHM1786C_SVG
Part No. F8429301ENR15
May 2015
Table of Contents
Safety Information..................................................................................5
Explanation of Safety Messages....................................................................... 5
Important Safety Instructions........................................................................... 6
Safety Decals................................................................................................. 7
Operator Safety.............................................................................................. 7
Introduction........................................................................................... 8
Model Identification........................................................................................8
Delivery Inspection....................................................................................... 12
Serial Plate Location..................................................................................... 12
Replacement Parts ........................................................................................12
Customer Service..........................................................................................12
Specifications and Dimensions.............................................................. 14
General Specifications...................................................................................14
Machine Dimensions.....................................................................................17
20-60 Pound Capacity Machines.................................................................17
80 and 100 Pound Capacity Machines ........................................................ 19
Mounting Bolt Hole Locations – 20 and 30 Pound Models................................21
Mounting Bolt Hole Locations - 40 and 60 Pound Models................................ 23
Mounting Bolt Hole Locations – 80 and 100 Pound Models ............................. 25
Floor Mounting Layout – 20-60 Pound Models................................................27
Floor Mounting Layout – 80 and 100 Pound Models........................................ 30
Installation........................................................................................... 35
Pallet Jack Cover Plate Removal (80 and 100 Pound Models Only)................... 35
Single Machine Foundation Requirements.......................................................35
Machine Installation with Existing Floor..................................................... 35
Elevated Pad Installation with Existing Floor............................................... 35
Elevated Base Frame Installation with Existing Floor................................... 35
New Foundation........................................................................................36
Isolated Pad Installation............................................................................. 36
Machine Foundation and Pad Installation........................................................ 37
Machine Installation......................................................................................39
Machine Mounting and Grouting....................................................................41
Drain Connection..........................................................................................44
Water Connection Requirements.................................................................... 46
Electrical Installation Requirements................................................................48
Input Power Conditioning..............................................................................49
Input Voltage Requirements....................................................................... 49
Circuit Breakers and Quick Disconnects......................................................... 49
© Copyright
2015, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
3
Part No. F8429301ENR15
Connection Specifications..............................................................................50
Single-Phase Connections.......................................................................... 50
Three-Phase Connections........................................................................... 50
Grounding................................................................................................ 50
Phase Adder..............................................................................................51
Thermal Overload Protector....................................................................... 51
North American Approval.......................................................................... 52
CE Approval.............................................................................................57
Steam Requirements (Steam Heat Option Only)...............................................62
Supply Dispensing........................................................................................ 62
External Supplies.......................................................................................... 62
Chemical Injection Using Internal 24VAC Control Transformer.................... 62
Chemical Injection Using External AC Power Source................................... 64
External Supply Signals............................................................................. 65
Connection of External Liquid Supplies.......................................................67
Start Up................................................................................................68
Pallet Jack cover Plate Installation (80 and 100 Pound Models Only).................68
Basket Rotation............................................................................................ 68
Operation............................................................................................. 69
Operating Instructions................................................................................... 69
Maintenance......................................................................................... 71
Maintenance.................................................................................................71
Daily........................................................................................................... 71
Beginning of Day...................................................................................... 71
End of Day............................................................................................... 71
Weekly........................................................................................................ 71
Monthly....................................................................................................... 72
Quarterly......................................................................................................73
Care of Stainless Steel................................................................................... 75
Disposal of Unit.................................................................................... 76
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4
Part No. F8429301ENR15
Safety Information
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,” and
“CAUTION”), followed by specific instructions, are found in this
manual and on machine decals. These precautions are intended
for the personal safety of the operator, user, servicer, and those
maintaining the machine.
DANGER
Indicates an imminently hazardous situation that, if
not avoided, will cause severe personal injury or
death.
WARNING
Indicates a hazardous situation that, if not avoided,
could cause severe personal injury or death.
CAUTION
Indicates a hazardous situation that, if not avoided,
may cause minor or moderate personal injury or
property damage.
Additional precautionary statements (“IMPORTANT” and
“NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor
machine damage will occur if the procedure is not followed.
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5
Part No. F8429301ENR15
Safety Information
Important Safety Instructions
•
WARNING
•
To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer,
follow these basic precautions:
W023
•
•
•
•
•
•
•
•
•
Read all instructions before using the washer.
Install the washer according the INSTALLATION instructions. Refer to the GROUNDING instructions in the INSTALLATION manual for the proper grounding of the washer. All connections for water, drain, electrical power and
grounding must comply with local codes and be made by licensed personnel when required. It is recommended that the
machine be installed by qualified technicians.
Do not install or store the washer where it will be exposed to
water and/or weather.
To prevent fire and explosion, keep the area around machine
free from flammable and combustible products. Do not add
the following substances or textiles containing traces of the
following substances to the wash water: gasoline, kerosene,
waxes, cooking oils, vegetable oils, machine oils, dry-cleaning solvents, flammable chemicals, thinners, or other flammable or explosive substances. These substances give off vapors
that could ignite, explode or cause the fabric to catch fire by
itself.
Under certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using a
washing machine or combination washer-dryer, turn on all hot
water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The
gas is flammable, do not smoke or use an open flame during
this time.
To reduce the risk of an electric shock or fire, DO NOT use
an extension cord or an adapter to connect the washer to the
electrical power source.
Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used
near children. This appliance is not intended for use by young
children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with
the appliance. This is a safety rule for all appliances.
DO NOT reach and/or climb into the tub or onto the washer,
ESPECIALLY if the wash drum is moving. This is an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.
Never operate the washer with any guards, panels and/or parts
removed or broken. DO NOT bypass any safety devices or
tamper with the controls.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
•
•
•
•
•
•
•
•
•
•
•
•
•
6
Use washer only for its intended purpose, washing textiles.
Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket or
tub.
Use only low-sudsing, no-foaming types of commercial detergent. Be aware that hazardous chemicals may be present.
Wear hand and eye protection when adding detergents and
chemicals. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all
warnings or precautions. To reduce the risk of poisoning or
chemical burns, keep them out of the reach of children at all
times [preferably in a locked cabinet].
Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener
or product.
Always follow the fabric care instructions supplied by the textile manufacturer.
Loading door MUST BE CLOSED any time the washer is to
fill, tumble or spin. DO NOT bypass the loading door switch
by permitting the washer to operate with the loading door
open. Do not attempt to open the door until the washer has
drained and all moving parts have stopped.
Be aware that hot water is used to flush the supply dispenser.
Avoid opening the dispenser lid while the machine is running.
Do not attach anything to the supply dispenser’s nozzles, if
applicable. The air gap must be maintained.
Do not operate the machine without the water reuse plug or
water reuse system in place, if applicable.
Be sure water connections have a shut-off valve and that fill
hose connections are tight. CLOSE the shut-off valves at the
end of each wash day.
Keep washer in good condition. Bumping or dropping the
washer can damage safety features. If this occurs, have washer checked by a qualified service person.
DANGER: Before inspecting or servicing machine, power
supply must be turned OFF. The servicer needs to wait for at
least 5 minutes after turning the power OFF and needs to
check for residual voltage with a voltage meter. The inverter
capacitor or EMC filter remains charged with high voltage for
some time after powering OFF. This is an imminently hazardous situation that, if not avoided, will cause severe personal
injury or death.
Do not repair or replace any part of the washer, or attempt any
servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions
that the user understands and has the skills to carry out. ALWAYS disconnect the washer from electrical, power and water supplies before attempting any service.
Disconnect the power by turning off the circuit breaker or by
unplugging the machine. Replace worn power cords.
Before the washer is removed from service or discarded, remove the door to the washing compartment.
Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions
which can produce bodily injury and/or property damage.
Part No. F8429301ENR15
Safety Information
NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the
washer.
Operator Safety
WARNING
NEVER insert hands or objects into basket until it
has completely stopped. Doing so could result in serious injury.
Any problems or conditions not understood should be reported to
the dealer, distributor, service agent or the manufacturer.
WARNING
SW012
The following maintenance checks must be performed daily:
Machine installations must comply with minimum
specifications and requirements stated in the applicable Installation Manual, any applicable municipal
building codes, water supply requirements, electrical
wiring regulations and any other relevant statutory
regulations. Due to varied requirements and applicable local codes, this machine must be installed, adjusted, and serviced by qualified maintenance personnel familiar with applicable local codes and the
construction and operation of this type of machinery. They must also be familiar with the potential
hazards involved. Failure to observe this warning
may result in personal injury, property damage,
and/or equipment damage, and will void the warranty.
1. Verify that all warning labels are present and legible, replace
as necessary.
2. Check door interlock before starting operation of the machine:
a. Attempt to start the machine with the door open. The machine should not start.
b. Close the door without locking it and start the machine.
The machine should not start.
c. Attempt to open the door while a cycle is in progress. The
door should not open.
If the door lock and interlock are not functioning properly, disconnect power and call a service technician.
3. Do not attempt to operate the machine if any of the following
conditions are present:
a. The door does not remain securely locked during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly grounded circuit.
W820
IMPORTANT: Ensure that the machine is installed on a
level floor of sufficient strength. Ensure that the recommended clearances for inspection and maintenance are
provided. Never allow the inspection and maintenance
space to be blocked.
Do not bypass any safety devices in the machine.
WARNING
WARNING
Operating the machine with severe out-of-balance
loads could result in personal injury and serious
equipment damage.
Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam
must be turned off and the pipe, connections, and
components allowed to cool before the pipe can be
touched.
W728
SW014
Safety Decals
Safety decals appear at crucial locations on the machine. Failure
to maintain legible safety decals could result in injury to the operator or service technician.
Use manufacturer-authorized spare parts to avoid safety hazards.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7
Part No. F8429301ENR15
Introduction
Introduction
Model Identification
Information in this manual is applicable to Design 2 models or
later. Refer to the 12th position of the model number (e.g.
*CN040*YVXU 2 001):
Models
20 POUND
CCN020HNF
CCN020HNV
CCN020KNF
CCN020KNV
HCD020LDF
HCD020LDV
HCL020GNF
HCL020HDF
HCL020HNF
HCL020HNV
HCL020KDF
HCL020KDV
HCL020KEV
HCL020KXV
HCN020GNF
HCN020HCF
HCN020HDF
HCN020HEF
HCN020HNF
HCN020HNV
HCN020HXF
HCN020HYF
HCN020KCF
HCN020KCV
HCN020KDF
HCN020KDV
HCN020KEF
HCN020KEV
HCN020KXF
HCN020KYF
HCN020KYV
HCU020GNF
HCU020HEF
HCU020HNF
HCU020HNV
HCU020HXF
HCU020KCF
HCU020KCV
HCU020KEV
HCU020KLF
HCU020KLV
HCU020KXV
HCU020KYF
HCU020KYV
HCZ020GNF
ICN020GNF
ICN020HNF
ICN020HNV
ICN020KCF
ICN020KCV
ICN020KDF
ICN020KDV
ICN020KEF
ICN020KEV
ICN020KNF
ICN020KNV
ICN020KXF
ICN020KYF
ICN020KYV
SCD020JDF
SCD020LDF
SCD020LDV
SCL020GNF
SCL020HNF
SCL020HNV
SCL020JCF
SCL020JCV
SCL020JDF
SCL020JDV
SCL020JEF
SCL020JEV
SCL020JXF
SCL020JYF
SCL020KNV
SCL020LCF
SCL020LDF
SCL020LDV
SCL020LEF
SCL020LEV
SCL020LLV
SCL020LXF
SCL020LYF
SCL020LYV
SCL020WEF
SCL020WEV
SCL020WXF
SCL020WYV
SCN020GNF
SCN020HNF
SCN020HNV
SCN020JCF
SCN020JCV
SCN020JDF
SCN020JEF
SCN020JXF
SCN020JYF
SCN020JYV
SCN020KNF
SCN020KNV
SCN020LCF
SCN020LCV
SCN020LDF
SCN020LDV
SCN020LEF
SCN020LEV
SCN020LYF
SCN020LYV
SCN020WCF
SCN020WCV
SCN020WDF
SCN020WDV
SCN020WEF
SCN020WEV
SCN020WYF
SCN020WYV
SCU020GNF
SCU020GNV
SCU020HNF
SCU020JCF
SCU020JCV
SCU020JDF
SCU020JDV
SCU020JEF
SCU020JEV
SCU020JLF
SCU020JLV
SCU020JXF
SCU020JXV
SCU020JYF
SCU020JYV
SCU020KNF
SCU020LCV
SCU020LDV
SCU020LEV
SCU020LLV
SCU020LXV
SCU020LYV
SCU020WCV
SCU020WDV
SCU020WEV
SCU020WXV
SCU020WYV
SCY020JDV
SCY020JEF
SCY020KNF
SCY020KNV
SCY020LEV
SCY020WEV
SCZ020GNF
UCL020GNF
UCL020GNV
UCL020HNF
UCL020HNV
UCL020KNF
UCL020KNV
UCN020GNF
UCN020GNV
UCN020HNF
UCN020HNV
UCN020KNF
UCN020KNV
UCU020GNF
UCU020GNV
UCU020HNF
UCU020HNV
UCU020KNF
UCU020KNV
UCY020KNF
UCY020KNV
UCZ020GNF
UCZ020HNF
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8
Part No. F8429301ENR15
Introduction
Models
30 POUND
CCN030HNF
CCN030HNV
CCN030KNF
CCN030KNV
HCD030LDF
HCD030LDV
HCL030GNF
HCL030HCF
HCL030HDF
HCL030HEF
HCL030HLF
HCL030HNF
HCL030HNV
HCL030KCV
HCL030KDF
HCL030KDV
HCL030KEF
HCL030KEV
HCL030KXV
HCL030KYF
HCN030GNF
HCN030GNV
HCN030HCF
HCN030HDF
HCN030HEF
HCN030HNF
HCN030HNV
HCN030HXF
HCN030HYF
HCN030KCF
HCN030KCV
HCN030KDF
HCN030KDV
HCN030KEF
HCN030KEV
HCN030KXF
HCN030KYF
HCN030KYV
HCU030GNF
HCU030GNV
HCU030HLF
HCU030HNF
HCU030HNV
HCU030HXF
HCU030KCF
HCU030KCV
HCU030KEV
HCU030KLV
HCU030KXV
HCU030KYF
HCU030KYV
HCZ030GNF
HCZ030HNV
ICN030GNF
ICN030HNF
ICN030HNV
ICN030KCF
ICN030KCV
ICN030KDF
ICN030KDV
ICN030KEF
ICN030KEV
ICN030KNF
ICN030KNV
ICN030KXF
ICN030KYF
ICN030KYV
SCD030JDF
SCD030LDF
SCD030LDV
SCL030GCF
SCL030GNF
SCL030GNV
SCL030HNF
SCL030HNV
SCL030JCF
SCL030JCV
SCL030JDF
SCL030JDV
SCL030JEF
SCL030JEV
SCL030JXF
SCL030JYV
SCL030KNF
SCL030KNV
SCL030KYF
SCL030LCV
SCL030LEF
SCL030LEV
SCL030LXF
SCL030LXV
SCL030LYV
SCL030WCF
SCL030WCV
SCL030WEF
SCL030WEV
SCL030WXF
SCL030WYV
SCN030GNF
SCN030GNV
SCN030HNF
SCN030HNV
SCN030JCF
SCN030JCV
SCN030JDF
SCN030JEF
SCN030JXF
SCN030JYF
SCN030JYV
SCN030KNF
SCN030KNV
SCN030LCF
SCN030LCV
SCN030LDF
SCN030LDV
SCN030LEF
SCN030LEV
SCN030LXF
SCN030LXV
SCN030LYF
SCN030LYV
SCN030WCF
SCN030WCV
SCN030WDF
SCN030WDV
SCN030WEF
SCN030WEV
SCN030WLV
SCN030WYF
SCN030WYV
SCU030GNF
SCU030GNV
SCU030HNF
SCU030JCF
SCU030JCV
SCU030JDF
SCU030JDV
SCU030JEF
SCU030JEV
SCU030JLF
SCU030JLV
SCU030JXF
SCU030JXV
SCU030JYF
SCU030JYV
SCU030KNF
SCU030KNV
SCU030LCV
SCU030LDV
SCU030LEF
SCU030LEV
SCU030LLV
SCU030LXV
SCU030LYV
SCU030WCV
SCU030WDV
SCU030WEV
SCU030WXV
SCU030WYV
SCY030JDV
SCY030JEF
SCY030KNF
SCY030KNV
SCY030LEV
SCY030WEV
SCZ030GNF
UCL030GNF
UCL030GNV
UCL030HNF
UCL030HNV
UCL030KNF
UCL030KNV
UCN030GNF
UCN030GNV
UCN030HNF
UCN030HNV
UCN030KNF
UCN030KNV
UCU030GNF
UCU030GNV
UCU030HNF
UCU030HNV
UCU030KNF
UCU030KNV
UCY030KNF
UCY030KNV
UCZ030GNF
UCZ030HNF
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9
Part No. F8429301ENR15
Introduction
Models
40 POUND
CCN040HNF
CCN040HNV
CCN040KNF
CCN040KNV
HCB040GNF
HCB040HCF
HCB040HNF
HCB040HNV
HCB040KCF
HCB040KCV
HCB040KEV
HCB040KLV
HCB040KXF
HCB040KYF
HCB040KYV
HCB040LDF
HCD040LDF
HCD040LDV
HCL040GNF
HCL040GNV
HCL040HCF
HCL040HDF
HCL040HEF
HCL040HNF
HCL040HNV
HCL040KCV
HCL040KDF
HCL040KDV
HCL040KEV
HCL040KXV
HCN040GNF
HCN040GNV
HCN040HCF
HCN040HDF
HCN040HEF
HCN040HNF
HCN040HNV
HCN040HXF
HCN040HYF
HCN040KCF
HCN040KCV
HCN040KDF
HCN040KDV
HCN040KEF
HCN040KEV
HCN040KXF
HCN040KYF
HCN040KYV
HCU040GNF
HCU040GNV
HCU040HLF
HCU040HNF
HCU040HNV
HCU040HXF
HCU040KCF
HCU040KCV
HCU040KEV
HCU040KLV
HCU040KXF
HCU040KXV
HCU040KYF
HCU040KYV
ICN040GNF
ICN040HNF
ICN040HNV
ICN040KCF
ICN040KCV
ICN040KDF
ICN040KDV
ICN040KEF
ICN040KEV
ICN040KNF
ICN040KNV
ICN040KXF
ICN040KYF
ICN040KYV
SCB040GNF
SCB040HNF
SCB040HNV
SCB040JCF
SCB040JCV
SCB040JDF
SCB040JDV
SCB040JEF
SCB040JEV
SCB040JLF
SCB040JLV
SCB040JXF
SCB040JXV
SCB040JYF
SCB040JYV
SCB040KNF
SCB040KNV
SCB040LCV
SCB040LDV
SCB040LEF
SCB040LEV
SCB040LLF
SCB040LXV
SCB040LYV
SCB040WCF
SCB040WCV
SCB040WDV
SCB040WEV
SCB040WXV
SCB040WYV
SCD040JDF
SCD040LDF
SCD040LDV
SCL040GCF
SCL040GNF
SCL040GNV
SCL040HNF
SCL040HNV
SCL040JCF
SCL040JCV
SCL040JDF
SCL040JDV
SCL040JEF
SCL040JEV
SCL040JXF
SCL040JXV
SCL040JYF
SCL040KNF
SCL040KNV
SCL040LCF
SCL040LCV
SCL040LEF
SCL040LEV
SCL040LLF
SCL040LXF
SCL040LYF
SCL040WCF
SCL040WEF
SCL040WEV
SCL040WLV
SCL040WXF
SCL040WXV
SCL040WYV
SCN040GNF
SCN040GNV
SCN040HNF
SCN040HNV
SCN040JCF
SCN040JCV
SCN040JDF
SCN040JEF
SCN040JXF
SCN040JYF
SCN040JYV
SCN040KNF
SCN040KNV
SCN040LCF
SCN040LCV
SCN040LDF
SCN040LDV
SCN040LEF
SCN040LEV
SCN040LLF
SCN040LXF
SCN040LXV
SCN040LYF
SCN040LYV
SCN040WCF
SCN040WCV
SCN040WDF
SCN040WDV
SCN040WEF
SCN040WEV
SCN040WYF
SCN040WYV
SCU040GNF
SCU040GNV
SCU040HNF
SCU040JCF
SCU040JCV
SCU040JDF
SCU040JDV
SCU040JEF
SCU040JEV
SCU040JLF
SCU040JLV
SCU040JXF
SCU040JXV
SCU040JYF
SCU040JYV
SCU040KNF
SCU040KNV
SCU040LCV
SCU040LDV
SCU040LEF
SCU040LEV
SCU040LLF
SCU040LLV
SCU040LXV
SCU040LYV
SCU040WCF
SCU040WCV
SCU040WDV
SCU040WEV
SCU040WXV
SCU040WYV
SCY040JDV
SCY040JEF
SCY040KNF
SCY040KNV
SCY040LEV
SCY040WEV
UCB040HNF
UCB040HNV
UCB040KNF
UCB040KNV
UCL040GNF
UCL040GNV
UCL040HNF
UCL040HNV
UCL040KNF
UCL040KNV
UCN040GNF
UCN040GNV
UCN040HNF
UCN040HNV
UCN040KNF
UCN040KNV
UCU040GNF
UCU040GNV
UCU040HNF
UCU040HNV
UCU040KNF
UCU040KNV
UCY040KNF
UCY040KNV
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10
Part No. F8429301ENR15
Introduction
Models
60 POUND
CCN060HNF
CCN060HNV
CCN060KNF
CCN060KNV
HCD060LDF
HCD060LDV
HCL060GNF
HCL060GNV
HCL060HCF
HCL060HDF
HCL060HNF
HCL060HNV
HCL060KDF
HCL060KDV
HCL060KEV
HCL060KXV
HCN060GNF
HCN060GNV
HCN060HCF
HCN060HDF
HCN060HEF
HCN060HNF
HCN060HNV
HCN060HXF
HCN060HYF
HCN060KCF
HCN060KCV
HCN060KDF
HCN060KDV
HCN060KEF
HCN060KEV
HCN060KXF
HCN060KYF
HCN060KYV
HCU060GNF
HCU060GNV
HCU060HLF
HCU060HNF
HCU060HNV
HCU060HXF
HCU060KCF
HCU060KCV
HCU060KEV
HCU060KLV
HCU060KYF
HCU060KYV
ICN060GNF
ICN060HNF
ICN060HNV
ICN060KCF
ICN060KCV
ICN060KDF
ICN060KDV
ICN060KEF
ICN060KEV
ICN060KNF
ICN060KNV
ICN060KXF
ICN060KYF
ICN060KYV
SCD060JDF
SCD060LDF
SCD060LDV
SCL060GNF
SCL060GNV
SCL060HNF
SCL060HNV
SCL060JCF
SCL060JCV
SCL060JDF
SCL060JDV
SCL060JEF
SCL060JEV
SCL060JXF
SCL060JYF
SCL060KNF
SCL060KNV
SCL060LCV
SCL060LEF
SCL060LEV
SCL060LLF
SCL060LXF
SCL060WEF
SCL060WEV
SCL060WXF
SCL060WYV
SCN060GNF
SCN060GNV
SCN060HNF
SCN060HNV
SCN060JCF
SCN060JCV
SCN060JDF
SCN060JEF
SCN060JXF
SCN060JYF
SCN060JYV
SCN060KNF
SCN060KNV
SCN060LCF
SCN060LCV
SCN060LDF
SCN060LDV
SCN060LEF
SCN060LEV
SCN060LXF
SCN060LXV
SCN060LYF
SCN060LYV
SCN060WCF
SCN060WCV
SCN060WDF
SCN060WDV
SCN060WEF
SCN060WEV
SCN060WYF
SCN060WYV
SCU060GNF
SCU060GNV
SCU060HNF
SCU060HNV
SCU060JCF
SCU060JCV
SCU060JDF
SCU060JDV
SCU060JEF
SCU060JEV
SCU060JLF
SCU060JLV
SCU060JXF
SCU060JXV
SCU060JYF
SCU060JYV
SCU060KNF
SCU060KNV
SCU060LCV
SCU060LDV
SCU060LEV
SCU060LLV
SCU060LXV
SCU060LYV
SCU060WCV
SCU060WDV
SCU060WEV
SCU060WXV
SCU060WYV
SCY060JDV
SCY060JEF
SCY060KNF
SCY060KNV
SCY060LEV
SCY060WEV
UCL060GNF
UCL060GNV
UCL060HNF
UCL060HNV
UCL060KNF
UCL060KNV
UCN060GNF
UCN060GNV
UCN060HNF
UCN060HNV
UCN060KNF
UCN060KNV
UCU060GNF
UCU060GNV
UCU060HNF
UCU060HNV
UCU060KNF
UCU060KNV
UCY060KNF
UCY060KNV
80 POUND
CCN080HNF
CCN080HNV
CCN080KNV
HCD080LDF
HCD080LDV
HCL080GNF
HCL080HNF
HCL080HNV
HCL080KDF
HCL080KDV
HCN080GNF
HCN080HCF
HCN080HCV
HCN080HDF
HCN080HNF
HCN080HNV
HCN080HYF
HCN080HYV
HCN080KCF
HCN080KCV
HCN080KDF
HCN080KDV
HCN080KEF
HCN080KEV
HCN080KYF
HCN080KYV
HCU080GNF
HCU080HCF
HCU080HNF
HCU080HXF
HCU080KCF
HCU080KCV
HCU080KYF
HCU080KYV
ICN080GNF
ICN080HNF
ICN080HNV
ICN080KCF
ICN080KCV
ICN080KDF
ICN080KDV
ICN080KEF
ICN080KEV
ICN080KNF
ICN080KNV
ICN080KYF
ICN080KYV
SCD080LDF
SCD080LDV
SCL080GNF
SCL080HNF
SCL080KNF
SCL080KNV
SCN080GNF
SCN080HNF
SCN080JCF
SCN080JCV
SCN080JDF
SCN080JYF
SCN080JYV
SCN080KNF
SCN080KNV
SCN080LCF
SCN080LCV
SCN080LDF
SCN080LDV
SCN080LEF
SCN080LYF
SCN080LYV
SCN080WCF
SCN080WCV
SCN080WDV
SCN080WEV
SCN080WYF
SCN080WYV
SCU080GNF
SCU080HNF
SCU080JCF
SCU080JCV
SCU080JDF
SCU080JDV
SCU080JEF
SCU080JEV
SCU080JLF
SCU080JLV
SCU080JXF
SCU080JXV
SCU080JYF
SCU080JYV
SCU080KNV
SCU080LCV
SCU080LDV
SCU080LEV
SCU080LXV
SCU080LYV
SCU080WCV
SCU080WDV
SCU080WEV
SCU080WXV
SCU080WYV
SCY080KNF
SCY080KNV
UCL080GNF
UCL080HNF
UCL080HNV
UCL080KNF
UCL080KNV
UCN080GNF
UCN080HNF
UCN080HNV
UCN080KNF
UCN080KNV
UCU080GNF
UCU080HNF
UCU080HNV
UCU080KNF
UCU080KNV
UCY080KNF
UCY080KNV
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
11
Part No. F8429301ENR15
Introduction
Models
100 POUND
CCN100HNF
CCN100HNV
HCL100GNF
HCL100HNV
HCL100KDF
HCL100KDV
HCN100GNF
HCN100HNV
HCN100KCF
HCN100KCV
HCN100KDF
HCN100KDV
HCN100KEF
HCN100KEV
HCN100KXF
HCN100KXV
HCN100KYF
HCN100KYV
HCU100HNV
ICN100GNF
ICN100HNF
ICN100HNV
ICN100KCF
ICN100KCV
ICN100KDV
ICN100KEV
ICN100KNF
ICN100KNV
ICN100KXV
ICN100KYV
SCL100GNF
SCL100KNV
SCN100GNF
SCN100JCF
SCN100KNF
SCN100KNV
SCN100LCF
SCN100LCV
SCN100LDF
SCN100LDV
SCN100LEF
SCN100LEV
SCN100LXF
SCN100LXV
SCN100LYF
SCN100LYV
SCN100WCF
SCN100WCV
SCN100WDF
SCN100WDV
SCN100WEF
SCN100WEV
SCN100WXF
SCN100WXV
SCN100WYF
SCN100WYV
SCU100KNV
SCY100KNF
UCL100GNF
UCL100HNF
UCL100HNV
UCL100KNF
UCL100KNV
UCN100GNF
UCN100HNF
UCN100HNV
UCN100KNV
UCU100HNF
UCU100HNV
UCU100KNF
UCU100KNV
UCY100KNV
1
Delivery Inspection
Upon delivery, visually inspect crate, protective cover, and unit
for any visible shipping damage. If signs of possible damage are
evident, have the carrier note the condition on the shipping papers before the shipping receipt is signed, or advise the carrier of
the condition as soon as it is discovered.
Serial Plate Location
The serial plate is located at the rear of the machine and inside
door. Provide the machine’s serial number and model number
when ordering parts or seeking technical assistance. Refer to Figure 1 .
CHM2433N_SVG
1. Serial Plate
Figure 1
Replacement Parts
If literature or replacement parts are required, contact the source
from which the machine was purchased or contact Alliance Laundry Systems at +1 (920) 748-3950 for the name and address of
the nearest authorized parts distributor.
Customer Service
For technical assistance, contact your local distributor or contact:
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12
Part No. F8429301ENR15
Introduction
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: +1 (920) 748-3121 Ripon, Wisconsin
Alliance International: +32 56 41 20 54 Wevelgem, Belgium
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13
Part No. F8429301ENR15
Specifications and Dimensions
Specifications and Dimensions
General Specifications
Specification
20
30
40
60
80
100
Overall Dimensions
Overall width, in. [mm]
26.0 [660]
Overall height, in [mm]
Design 2
Design 3
Overall depth, in. [mm]
29.0 [737]
42.0 [1067] 44.95
[1142]
43.0 [1092]
30.63 [778] 34.06 [865] 41.5 [1054] 41.5 [1054]
47.2 [1199] 49.89
[1267]
56.16
[1426]
56.16
[1426]
30.85 [784]
35.29 [896] 42.25
[1073]
4.7 [1135]
48.6 [1234] 52.6 [1336]
Net weight, lbs. [kg]
335 [152]
460 [209]
550 [249]
695 [315]
1210 [549] 1260 [572]
Standard shipping weight, lbs. [kg]
365 [166]
495 [225]
59 [268]
745 [338]
1260 [572] 1310 [594]
Standard shipping volume, ft3 [m3]
Design 2
26.5 [0.75] 36 [1.01]
44 [1.24]
57 [1.61]
81 [2.29]
87 [2.4]
Design 3
27 [0.77]
Design 2
28 x 33.8 x
48.4 [711 x
859 x
1229]
31.5 x 38.3
x 51.3 [800
x 973 x
1303]
32.5 x 43.5
x 53.6 [826
x 1105 x
1361]
37.5 x 46.9
x 56.3 [953
x 1191 x
1430]
44 x 54.5 x
58.6 [1118
x 1384 x
1488]
44 x 58.5 x
58.6 [1118
x 1486 x
1488]
Design 3
28 x 33.8 x
49.4 [711 x
859 x
1256]
590 [268]
690 [313]
860 [390]
1385 [628] 1435 [651]
54 [1.52]
78 [2.20]
105 [2.97]
112 [3.17]
36 x 41.3 x
55 [914 x
1049 x
1397]
37 x 45.9 x
55 [940 x
1166 x
1397]
42 x 49.9 x
64 [1067 x
1267 x
1626]
48.5 x 57.5
x 65.1
[1232 x
1461 x
1654]
48.5 x 61.5
x 65.1
[1232 x
1562 x
1654]
Weight and Shipping Information
Standard shipping dimensions
(WxDxH), in. [mm]
Slat crate shipping weight, lbs. [kg ]
450 [204]
Slat crate shipping volume, ft3 [m3]
Design 2
36.2 [1.04] 47 [1.33]
Design 3
38 [1.07]
Design 2
32.5 x 36.8
x 49.8 [826
x 935 x
1240]
Design 3
32.5 x 36.8
x 55 [826 x
935 x
1397]
Slat crate shipping dimensions
(WxDxH), in. [mm]
Wash Cylinder Information
Cylinder diameter, in. [mm]
21 [533]
24 [610]
26.3 [668]
30 [762]
36 [914]
36 [914]
Cylinder depth, in. [mm]
13.8 [350]
16 [406]
20.3 [515]
22 [559]
21.9 [556]
25.9 [657]
Cylinder volume, ft3 [l]
2.8 [79.3]
4.2 [119]
6.3 [178]
9.00 [255]
12.9 [365]
15.2 [430]
Table 1 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
14
Part No. F8429301ENR15
Specifications and Dimensions
Specification
20
30
40
60
80
100
Perforation size, in. [mm]
0.188 [4.78]
0.188
[4.78]
0.188
[4.78]
0.188
[4.78]
0.188
[4.78]
0.188
[4.78]
Perforation open area, %
17.3
18.6
18.8
18.8
19.6
20.2
11.6 [295]
14.3 [363]
16.3 [414]
16.3 [414]
18.5 [470]
18.5 [470]
Height of door bottom above floor, in. 14.38 [365]
[mm]
14 [356]
14.56 [370] 14.94 [379] 17.91 [455] 17.91 [455]
Height of door opening above floor,
in. [mm]
17 [432]
17 [431]
17.74 [451] 18.12 [460] 20.77 [528] 20.77 [528]
.05
.09
.10
.15
.19
.19
.06
.11
.14
.22
.28
.28
400 [101]
450 [113]
510 [129]
750 [189]
950 [239]
950 [239]
Number of motors in drive train
1
1
1
1
1
1
Drive motor power, hp [kW]
*
2 [1.5]
2 [1.5]
3 [2.2]
5 [3.7]
5 [3.7]
Gentle wash/reverse speed, RPM [G]
37 [0.4]
34 [0.4]
33 [0.4]
31 [0.4]
28 [0.4]
28 [0.4]
Wash/reverse speed, RPM [G]
51 [0.8]
48 [0.8]
46 [0.8]
43 [0.8]
39 [0.8]
39 [0.8]
Distribution speed, RPM [G]
92 [2.5]
86 [2.5]
82 [2.5]
77 [2.5]
70 [2.5]
70 [2.5]
Extract Speed 1 (very low), RPM [G]
301 [27]
282 [27]
269 [27]
252 [27]
230 [27]
230 [27]
Extract Speed 2 (low), RPM [G]
518 [80]
485 [80]
464 [80]
434 [80]
396 [80]
396 [80]
Extract Speed 3 (medium), RPM [G]
579 [100]
542 [100]
518 [100]
485 [100]
443 [100]
443 [100]
Extract Speed 4 (high), RPM [G]
648 [120]
606 [120]
579 [120]
542 [120]
495 [120]
495 [125]
Extract Speed 5 (very high), RPM [G] 710 [150]
664 [150]
635 [150]
594 [150]
542 [150]
542 [150]
Extract Speed 6 (ultra high), RPM [G] 819 [200]
766 [200]
733 [200]
686 [200]
626 [200]
568 [165]
Door Opening Information
Door opening size, in. [mm]
Power Consumption
Average power used per No load
cycle, kW-hr. (X-voltage
80 % load
shown)
Estimated Building Heat Load
HVAC load, Btu/hr. [Kcal/hr.] (Nonheat models)
Drive Train Information
Cylinder Speeds
Direct Steam Heating (Optional)
Steam inlet connection size, NPT
1/2
1/2
1/2
1/2
1/2
1/2
Number of steam inlets
**
**
1
1
1
1
LOW
.74 [0.34]
.94 [0.43]
2.09 [0.94] 3.80 [1.63] 3.80 [1.72] 3.80 [1.72]
MED
1.07 [0.49]
1.28 [0.58] 2.40 [1.09] 4.65 [2.11] 4.65 [2.11] 5.49 [2.49]
HIGH
1.44 [0.65]
1.74 [0.79] 2.84 [1.29] 5.79 [2.63] 5.79 [2.63] 6.84 [3.10]
Steam required to raise
bath water temperature
10°F/lbs. [10°C/kg]
Table 1 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
15
Part No. F8429301ENR15
Specifications and Dimensions
Specification
Average steam consumption per cycle, bHP
20
30
40
60
80
100
.34
.41
.78
.98
1.34
1.58
200V
5.4
5.4
10.8
10.8
19.1
19.1
240V
7.8
7.8
15.6
15.6
27.4
27.4
380V
6.5
6.5
13.0
13.0
17.2
17.2
415V
7.8
7.8
15.5
15.5
20.5
20.5
480V
N/A
N/A
15.6
15.6
27.4
27.4
Electrical heating elements
3
3
6
6
6
6
Electrical heat element size, kW
2.6
2.6
2.6
2.6
4.2
4.2
58
58
58
58
58
58
100G
52
59
59
59
69
69
200G
61
66
66
66
76
73
Electrical Heating
Total electrical heating
capacity, kW
Input Voltage
Noise Emissions
dBA
Wash
Extract
* For B, Q and X-voltage models = 1 hp [.75 kW] and for N and P-voltage models = 2 hp [1.7 kW]
** 20 and 30 pound models can be prep for steam and a kit is available for conversion.
N/A = Not Applicable
Table 1
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
16
Part No. F8429301ENR15
Specifications and Dimensions
Machine Dimensions
20-60 Pound Capacity Machines
20-60 Pound Models
K
J
I
H
G
3
F
4
1
Q
5
2
W
L
A B C
V
D
R
S
M
6
E
1.
2.
3.
4.
5.
6.
T
U
N
O
P
CHM2434N_SVG
Supply Dispenser
Input Power Block Compartment
Hot Water Inlet
Cold Water Inlet
Vacuum Breaker
Drain Outlet
Figure 2
Machine Capacity Dimensions - 20-60 Pound Models, in. [mm]
Specification
20
20
(Design 2)
(Design 3)
30
40
60
A
38.0 [965]
39.0 [991]
40.94 [1040]
43.19 [1097]
45.88 [11.65]
B
35.0 [889]
36.0 [914]
37.94 [964]
40.19 [1021]
42.88 [1089]
C
34.52 [902]
35.52 [902]
37.46 [951]
39.71 [1009]
42.4 [1077]
D
4.7 [119]
4.7 [119]
4.14 [105]
4.51 [115]
4.87 [124]
Table 2 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
17
Part No. F8429301ENR15
Specifications and Dimensions
Machine Capacity Dimensions - 20-60 Pound Models, in. [mm]
Specification
20
20
(Design 2)
(Design 3)
30
40
60
E
7.83 [199]
7.83 [199]
9.33 [237]
8.82 [224]
9.89 [251]
F
2.99 [76]
2.99 [76]
2.99 [76]
2.99 [76]
2.99 [76]
G
6.94 [176]
6.94 [176]
6.94 [176]
6.94 [176]
6.94 [176]
H
8.82 [224]
8.82 [224]
8.82 [224]
8.82 [224]
8.82 [224]
I
15.15 [385]
15.15 [385]
15.15 [385]
15.15 [385]
19.9 [505]
J
15.65 [398]
15.65 [398]
15.65 [398]
15.65 [398]
20.4 [518]
K
N/A
N/A
N/A
19.48 [495]
22.91 [582]
L
N/A
N/A
N/A
44.61 [1133]
47.3 [1201]
M
0.34 [9]
0.34 [9]
0.34 [9]
2.0 [51]
2.0 [51]
N
26.83 [681]
26.83 [681]
31.5 [800]
35.52 [902]
38.62 [981]
O
27.31 [694]
27.31 [694]
31.82 [808]
36.96 [939]
39.45 [1002]
P
30.85 [784]
30.85 [784]
35.29 [896]
42.25 [1073]
44.7 [1135]
Q
9.0 [254]
9.0 [254]
9.0 [254]
9.0 [254]
9.0 [254]
R
23.01 [584]
23.01 [584]
24.0 [610]
26.0 [660]
26.38 [670]
S
17.0 [432]
17.0 [432]
17.0 [432]
17.74 [451]
18.12 [460]
T
14.38 [365]
14.38 [365]
14 [356]
14.56 [370]
14.94 [379]
U
26.0 [660]
26.0 [660]
29.0 [737]
30.63 [778]
34.06 [865]
V
42.0 [1067]
43.0 [1092]
44.95 [1142]
47.2 [1199]
49.89 [1267]
W
1.5 [38]
1.5 [38]
1.5 [38]
1.5 [38]
1.5 [38]
N/A = Not Applicable
Table 2
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18
Part No. F8429301ENR15
Specifications and Dimensions
80 and 100 Pound Capacity Machines
80 and 100 Pound Models
M
L
K
J
I
H
3
4
G
2
1
S
5 6
F
AA
7
A B C
Z
N
T
D
U
8
E
V
O
Y
P
X
Q
W
R
CHM2435N_SVG
1.
2.
3.
4.
5.
6.
7.
8.
Supply Dispenser
Input Power Block Compartment
Auxiliary Hot Water Inlet
Auxiliary Cold Water Inlet
Cold Water Inlet
Hot Water Inlet
Vacuum Breaker
Drain Outlet
Figure 3
Machine Capacity Dimensions - 80 and 100 Pound Models, in. [mm]
A
51.82 [1316]
O
1.36 [35]
B
50.32 [1278]
P
39.24 [997]
C
48.68 [1236]
Q
80
44.16 [1122]
100
48.16 [1223]
Table 3 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
19
Part No. F8429301ENR15
Specifications and Dimensions
Machine Capacity Dimensions - 80 and 100 Pound Models, in. [mm]
D
6.41 [163]
R
80
48.6 [1234]
100
52.6 [1336]
E
2.55 [65]
S
9.0 [229]
F
2.99 [76]
T
30.91 [785]
G
6.94 [176]
U
20.77 [528]
H
8.82 [224]
V
17.91 [455]
I
16.66 [423]
W
41.5 [1054]
J
18.18 [462]
X
26.15 [664]
K
21.65 [550]
Y
3.57 [91]
L
26.15 [664]
Z
56.16 [1426]
M
30.35 [771]
AA
1.5 [38]
N
53.57 [1361]
Table 3
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
20
Part No. F8429301ENR15
Specifications and Dimensions
Mounting Bolt Hole Locations – 20 and 30 Pound Models
20 and 30 Pound Models (refer to Table 4 )
B
D
C
E
A
G
I
H
F
J
K
L
P
M
N
O
1
Q
2
3
R
CHM2395N_SVG
1. Elevated Base Width
2. Front of Base
3. Machine Width
Figure 4
Mounting Bolt Hole Locations – 20 and 30 Pound Models, in. [mm]
Specification
20
30
A
2 [51]
2 [51]
B
26.37 [670]
29.38 [746]
C
20.88 [530]
23.89 [607]
Table 4 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
21
Part No. F8429301ENR15
Specifications and Dimensions
Mounting Bolt Hole Locations – 20 and 30 Pound Models, in. [mm]
Specification
20
30
D
2.75 [70]
2.75 [70]
E
0.18 [5]
0.18 [5]
F
0.25 [6]
0.25 [6]
G
0.64 [16]
0.64 [16]
H
2.71 [69]
2.37 [60]
I
2.15 [55]
1.81 [46]
J
4.69 [119]
4.69 [119]
K
0.19 [5]
0.19 [5]
L
9.64 [245]
10.5 [267]
M
23.94 [608]
28.94 [735]
N
24.69 [627]
29.69 [754]
O
27.92 [709]
32.59 [828]
P
20.65 [524]
23.5 [597]
Q
26.37 [670]
29.38 [746]
R
26 [660]
29.02 [737]
Table 4
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
22
Part No. F8429301ENR15
Specifications and Dimensions
Mounting Bolt Hole Locations - 40 and 60 Pound Models
40 and 60 Pound Models (refer to Table 5 )
B
D
C
E
A
F
H
G
I
K
J
O
M
L
N
1
P
2
3
Q
CHM2397N_SVG
1. Elevated Base Width
2. Front of Base
3. Machine Width
Figure 5
Mounting Bolt Hole Locations - 40 and 60 Pound Models, in. [mm]
Specification
A
40
60
2 [51]
2 [51]
Table 5 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
23
Part No. F8429301ENR15
Specifications and Dimensions
Mounting Bolt Hole Locations - 40 and 60 Pound Models, in. [mm]
Specification
40
60
B
30.88 [784]
34.44 [875]
C
26 [660]
30 [762]
D
2.44 [62]
2.22 [56]
E
0.12 [3]
0.12 [3]
F
0.64 [16]
0.64 [16]
G
2.37 [60]
2.37 [60]
H
2 [51]
1.75 [44]
I
4.75 [121]
5.15 [131]
J
1.19 [30]
1.25 [32]
K
12.5 [318]
11.93 [303]
L
32.5 [826]
36 [914]
M
33.54 [852]
36.87 [936]
N
37.25 [946]
40.5 [1029]
O
23.63 [600]
27.5 [699]
P
30.88 [784]
34.44 [875]
Q
30.63 [778]
34.19 [868]
Table 5
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
24
Part No. F8429301ENR15
Specifications and Dimensions
Mounting Bolt Hole Locations – 80 and 100 Pound Models
80 and 100 Pound Models (refer to Table 6 )
A
D
E
F
B
C
N
G
A
B
B
O
A
H
P
A
B
I
B A
Q
J
R
K
L
A
B
B
A
M
CHM2399N_SVG
NOTE: For single machine installations or two machines installed back to back, use the outside bolt holes
marked “A”. For multiple machines installed side by side with minimum clearance, use the inside bolt holes
marked “B”.
Figure 6
Mounting Bolt Hole Locations – 80 and 100 Pound Models, in. [mm]
Specification
80
100
A
41.5 [1054]
41.5 [1054]
B
39.62 [1006]
39.62 [1006]
C
31.62 [803]
31.62 [803]
Table 6 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
25
Part No. F8429301ENR15
Specifications and Dimensions
Mounting Bolt Hole Locations – 80 and 100 Pound Models, in. [mm]
Specification
80
100
D
.94 [24]
.94 [24]
E
4.94 [124]
4.94 [124]
F
6.63 [164]
6.63 [164]
G
3.3 [84]
3.3 [84]
H
16 [406]
16 [406]
I
35 [889]
35 [889]
J
37.3 [947]
37.3 [947]
K
42.2 [1073]
N/A
L
N/A
46.2 [1260]
M
1 [25]
1 [25]
N
1.96 [50]
1.96 [50]
O
Outside
42.72 [1085]
35.43 [900]
P
Inside
52.86 [1342]
47.16 [1197]
Q
Outside
35.43 [900]
42.72 [1085]
R
Inside
47.16 [1197]
52.86 [1342]
N/A = Not Applicable
Table 6
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
26
Part No. F8429301ENR15
Specifications and Dimensions
Floor Mounting Layout – 20-60 Pound Models
Dimensional Clearances - Single Machine Mount (refer to Table 7 )
1
A
2
B
C
4
3
C
B
5
1.
2.
3.
4.
5.
CHM2426N_SVG
Wall
Rear of Base
Edge of Concrete Pad
Machine 1
Front of Base
Figure 7
Dimensional Clearances - Single Machine Mount - 20-60 Pound Models, in. [mm]
Description
20
30
40
60
A
Distance to wall (minimum)
24 [610]
24 [610]
24 [610]
24 [610]
B
Distance of machine base to
edge of pad (minimum)
3.44 [87]
4 [102]
3.99 [101]
5.99 [152]
C
Distance of machine base to
edge of pad (minimum)
2.52 [64]
2.51 [64]
2.81 [71]
5.18 [131]
Table 7
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
27
Part No. F8429301ENR15
Specifications and Dimensions
Dimensional Clearances - Side-by-Side Mount (refer to Table 8 )
1
A
2
2
2
3
4
5
3
6
B
B
6
6
CHM2375N_SVG
1.
2.
3.
4.
5.
6.
Wall
Rear of Base
Machine 1
Machine 2
Machine 3
Front of Base
Figure 8
Dimensional Clearances - Side-by-Side Mount - 20-60 Pound Models, in. [mm]
Description
A
Distance to wall (minimum)
B
20
24 [610]
30
40
60
24 [610]
24 [610]
24 [610]
Mounted without bases (min- 5.14 [131]
imum)
5.12 [130]
4.63 [118]
4.06 [103]
Mounted with bases (minimum)
5.5 [139]
4.88 [124]
4.44 [112]
5.5 [139]
Table 8
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
28
Part No. F8429301ENR15
Specifications and Dimensions
Dimensional Clearances - Back-to-Back Mount (refer to Table 9 )
1
B
2
3
5
A
3
4
1
B
CHM2376N_SVG
1.
2.
3.
4.
5.
Front of Machine
Machine 2
Rear of Machine
Machine 1
Edge of Concrete Pad
Figure 9
Dimensional Clearances - Back-to-Back Mount - 20-60 Pound Models, in. [mm]
Description
20
30
40
60
A
Adjacent rear bolt spacing
(minimum)
28.3 [719]
27.6 [702]
28.0 [710]
27.5 [699]
B
Distance from front bolt to
edge of pad (minimum)
5.26 [134]
5.26 [134]
6.19 [157]
8.9 [226]
Table 9
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
29
Part No. F8429301ENR15
Specifications and Dimensions
Floor Mounting Layout – 80 and 100 Pound Models
Standard Mount for Single Machine (refer to Table 10 )
1
A
2
B
C
4
3
C
B
5
1.
2.
3.
4.
5.
CHM2427N_SVG
Wall
Rear of Base
Edge of Concrete Pad
Machine 1
Front of Base
Figure 10
Standard Mount for Single Machine - 80 and 100 Pound Models, in. [mm]
Description
80-100
A
Distance to wall (minimum)
24 [610]
B
Distance of machine base to edge of pad (minimum)
4.98 [126]
C
Distance of machine base to edge of pad (minimum)
8 [203]
Table 10
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
30
Part No. F8429301ENR15
Specifications and Dimensions
Standard Mount Side-by-Side (refer to Table 11 )
1
A
2
2
3
4
5
1.
2.
3.
4.
5.
B
5
PHM819N_SVG
Wall
Rear of Base
Machine 1
Machine 2
Front of Base
Figure 11
Standard Mount Side-by-Side - 80 and 100 Pound Models, in. [mm]
Description
80-100
A
Distance to wall (minimum)
24 [610]
B
Adjacent unit bolt spacing (minimum)
6 [152]
Table 11
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
31
Part No. F8429301ENR15
Specifications and Dimensions
Close Mount Side-by-Side (refer to Table 12 )
1
A
2
2
3
4
5
1.
2.
3.
4.
5.
B
5
PHM820N_SVG
Wall
Rear of Base
Machine 1
Machine 2
Front of Base
Figure 12
Close Mount Side-by-Side - 80 and 100 Pound Models, in. [mm]
Description
80-100
A
Distance to wall (minimum)
24 [610]
B
Adjacent unit bolt spacing (minimum)
10.38 [264]
IMPORTANT: When close mounting, bolt machine using inside bolt holes.
Table 12
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
32
Part No. F8429301ENR15
Specifications and Dimensions
Back-to-Back Mount (refer to Table 13 )
1
B
2
3
A
5
3
4
1
B
PHM810N_SVG
1.
2.
3.
4.
5.
Front of Machine
Machine 2
Rear of Machine
Machine 1
Edge of Concrete Pad
Figure 13
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
33
Part No. F8429301ENR15
Specifications and Dimensions
Back-to-Back Mount - 80 and 100 Pound Models, in. [mm]
Description
80-100
A
Adjacent rear bolt spacing (minimum)
33.3 [846]
B
Distance from front bolt to edge of pad (minimum)
8 [203]
Table 13
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
34
Part No. F8429301ENR15
Installation
Installation
Pallet Jack Cover Plate Removal (80
and 100 Pound Models Only)
Prior to installing an 80 and 100 pound machine, the optional pallet jack cover plate can be removed in preparation of re-installing
to machine base frame after machine installation.
1. Locate cover plate on back panel.
2. Remove back panel.
3. Remove all hardware holding cover plate on back panel, refer
to Figure 14 . DO NOT DISCARD HARDWARE.
4. Remove cover plate.
1
2
3
WARNING
To reduce the risk of fire, serious injury, property
damage and/or death, install the machine on a level
(within 3/8 inch), uncovered concrete floor of sufficient strength at grade.
W787
For new foundations a mounting bolt template or an elevated
metal base frame is available at extra cost. For all installations a
concrete hardware kit is available at extra cost.
The machine must be anchored to a smooth level surface so that
the entire base of the machine is supported and rests on the
mounting surface.
IMPORTANT: Do not permanently support the machine
on only four points with spacers. Grouting is required
and spacers must be removed.
1
Machine Installation with Existing Floor
4
CHM2400N_SVG
1.
2.
3.
4.
Nut
Stud
Cover Plate
Back Panel
The existing floor slab must meet minimum requirements shown
in Machine Foundation and Pad Installation per machine model.
The floor must be reinforced concrete without voids under slab.
If the floor meets these requirements and an elevated pad is NOT
desired, refer to Figure 16 and proceed to Machine Mounting and
Grouting section.
Figure 14
5. Re-install back panel.
NOTE: Refer to Pallet Jack cover Plate Installation (80 and
100 Pound Models Only) section to install cover plate to
machine base after machine installation.
Single Machine Foundation Requirements
A minimum 3500 psi (refer to rating per supplier) reinforced concrete set on a prepared bed is required for all new machine installations.
NOTE: Do not mount on wooden floors, tile floors, elevated floor levels, stacked multiple base frames, or
over basements or crawl spaces because of the high
extract speed and the G-forces exerted. For 80 pound
models and larger, do not mount on metal base frames.
Elevated Pad Installation with Existing Floor
The existing floor slab must meet minimum requirements shown
in Machine Foundation and Pad Installation per machine. The
floor must be reinforced concrete without voids under slab. If the
slab meets these requirements and an elevated pad is desired, refer to Figure 17 and proceed to Machine Foundation and Pad Installation section.
Elevated Base Frame Installation with Existing Floor
The existing floor slab must meet minimum requirements shown
in Machine Foundation and Pad Installation per machine. The
floor must be reinforced concrete without voids under slab. If the
slab meets these requirements and an elevated base frame is desired, refer to Figure 16 and Figure 18 and proceed to Machine
Mounting and Grouting section.
Thoroughness of detail must be stressed with all foundation work
to ensure a stable unit installation, eliminating possibilities of excessive vibration during extract.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
35
Part No. F8429301ENR15
Installation
CHM2412N_SVG
Figure 15
New Foundation
If the existing floor slab does not meet the single machine foundation requirements per model, refer to Figure 18 and proceed
to Machine Foundation and Pad Installation section.
Isolated Pad Installation
This type of installation is NOT recommended. Installer MUST
consult a Structural Engineer for concrete specifications and requirements for installations that will not be tied into adjacent
foundations.
IMPORTANT: The above instructions and recommendations are conservative specifications for a typical installation based on consultations with a structural engineer. Alliance Laundry Systems stands behind all installations meeting these specifications. For alternate
installation specifications based on your soil type, location, building structure, unique floor geometry, machine types, and utilities, consult a structural engineer
in your local area.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
36
Part No. F8429301ENR15
Installation
Machine Foundation and Pad Installation
ted by the machine during extract. This concrete pad, recommended not to exceed 8 inches [203 mm] above existing floor, must
be placed, reinforced with rebar and tied to the existing floor. Refer to Table 14 , Figure 16 , Figure 17 and Figure 18 for multiple
machine installations.
A concrete pad may be constructed to elevate a machine. Care
must be exercised in the design of the pad due to the force exer-
Machine Foundation and Pad Installation, in. [mm]
Specification
20
Minimum Foun- F-speed
dation Thickness
V-speed
4 [102]
Minimum Excavation Depth
8 [203]
30
40
80-100
4 [102]
4 [102]
6 [152]
6 [152]
6 [152]
9 [229]
8 [203]
8 [203]
12 [305]
12 [305]
12 [305]
15 [381]
34.4 x 39.5 [874
x 1003]
36.5 x 43.5 [927
x 1105]
44.8 x 50.6
[1139 x 1285]
57.5 x 49.2
[1461 x 1250]
Two machines, Side-by-side (WxD) 57.54 x 34.8
[1462 x 884]
63.52 x 39.5
[1613 x 1003]
67.38 x 43.5
[1711 x 1105]
78.98 x 50.6
[2006 x 1285]
99.5 x 49.2
[2527 x 1250]
Two machines, Back-to-back
(WxD)
34.4 x 98.37
[874 x 2499]
36.5 x 115.23
[927 x 2927]
44.8 x 119.48
[1138 x 3035]
51.5 x 130.56
[1308 x 3316]
F-speed
4 [102]
60
8 [203]
V-speed
Minimum Pad Size
Single machine (WxD)
31.4 x 34.8 [798
x 884]
31.4 x 88.63
[798 x 2251]
NOTE: Inside and outside mounting only available on 80 and 100 pound models.
N/A = Not Applicable
Table 14
IMPORTANT: Do NOT install a pad on top of the existing floor. The foundation and pad must be constructed
and tied together as one piece.
If the existing floor is not reinforced concrete at least of minimum thickness (depending on model), an elevated pad is desired
or multiple machines are to be installed, the following steps must
be performed (refer to Figure 16 , Figure 17 , and Figure 18 ):
1. Cut a hole larger on all sides than the machine base through
the existing floor, refer to Table 14 .
2. Excavate to a depth as indicated in Table 14 from the top of
the existing floor.
3. If installing a foundation with elevated pad, prepare a form
for the above-ground portion of the foundation. Verify that
the top of the foundation is level. The height of the foundation
pad must not exceed 8 inches [203 mm] above the existing
floor.
4. Backfill with clean fill dirt.
5. Compact backfill, making sure to allow for correct concrete
thickness.
6. Drill holes [refer to manufacturer’s requirements for drill hole
size] for the perimeter reinforcing bar at a depth of 2.5 inches
[64 mm] into the existing floor. The reinforcing should be 12
inches [305 mm] on center each way around entire perimeter.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7. Clean out debris from each reinforcing bar hole.
8. Fill half the hole depth with acrylic adhesive.
9. Using #4 (60 ksi) reinforcing bar, tie new pad to existing floor
making sure to tie reinforcing bars at the intersections and using proper reinforcing bar supports to hold bars at the proper
depth in the pad.
10. Allow adhesive around reinforcing bar to cure properly, refer
to adhesive manufacturer for recommended cure times.
11. Completely fill with 3500 psi minimum concrete up to the existing foundation level plus any added level (maximum of 8
inches [203 mm]) for the desired elevated pad. The concrete
must be poured so that the entire foundation and pad cures as
one piece.
12. Allow concrete to cure, refer to manufacturer’s recommended
cure times.
13. Using a mounting bolt template, elevated base frame or the
machine base, mark where the holes should be drilled to
mount the machine.
NOTE: As an alternate method, cast in the Grade 5
(minimum SAE rating), 5/8 inches [16 mm] for 20-60
pound models and 3/4 inch [19 mm] for 80-100
pound models anchor bolts as the concrete is poured, refer to Figure 20 and Table 18 .
37
Part No. F8429301ENR15
Installation
14. Proceed to Machine Mounting and Grouting section.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
38
Part No. F8429301ENR15
Installation
Machine Installation
Existing Floor (refer to Table 15)
1
A
2
PHM814N_SVG
1. Existing Floor with 3500 PSI (minimum) Concrete
2. Compacted Fill (minimum 6 in. [152 mm])
Figure 16
Existing Floor, in. [mm]
Description
A
Required thickness of existing floor
(minimum)
20-30
4 [102]
40-60
(F-speed)
4 [102]
40-60
(V-speed)
6 [152]
80-100
9 [229]
Table 15
Elevated Pad (refer to Table 16)
2
B
C
3
1
A
4
D
5
E
PHM852N_SVG
1.
2.
3.
4.
5.
Existing Floor
3500 PSI (minimum) Concrete
Reinforcing Bar
Perimeter Reinforcing Bar
Compacted Fill (minimum 6 in. [152 mm])
Figure 17
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
39
Part No. F8429301ENR15
Installation
Elevated Pad, in. [mm]
Description
20-30
40-60
(F-speed)
40-60
(V-speed)
80-100
A
Height of elevated pad above floor
(maximum)
8 [203]
8 [203]
8 [203]
8 [203]
B
Distance between reinforcing bars
(maximum)
12 [305]
12 [305]
12 [305]
12 [305]
C
Length of reinforcing bar extending in- 2.5 [64]
to existing floor (minimum)
2.5 [64]
2.5 [64]
2.5 [64]
D
Total depth of foundation (concrete
plus 6 in. [152 mm] fill) (minimum)
8 [203]
8 [203]
12 [305]
15 [381]
E
Required thickness of existing floor
(minimum)
4 [102]
4 [102]
6 [152]
6 [152]
Table 16
Tie-in to Existing Floor (refer to Table 17)
1
4
2
C
A
3
D
B
5
1.
2.
3.
4.
5.
CHM2390N_SVG
Existing Floor
3500 PSI (minimum) Concrete
Reinforcing Bar
Perimeter Reinforcing Bar
Compacted Fill (minimum 6 in. [152 mm])
Figure 18
Tie-in to Existing Floor, in. [mm]
Description
A
Required thickness of existing floor
(minimum)
20-30
4 [102]
40-60
(F-speed)
4 [102]
40-60
(V-speed)
6 [152]
80-100
6 [152]
Table 17 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
40
Part No. F8429301ENR15
Installation
Tie-in to Existing Floor, in. [mm]
Description
40-60
(F-speed)
20-30
40-60
(V-speed)
80-100
B
Total depth of foundation (concrete
plus 6 in. [152 mm] fill)(minimum)
8 [203]
8 [203]
12 [305]
15 [381]
C
Distance between reinforcing bars
(minimum)
12 [305]
12 [305]
12 [305]
12 [305]
D
Length of reinforcing bar extending in- 2.5 [64]
to existing floor (minimum)
2.5 [64]
2.5 [64]
2.5 [64]
Table 17
Machine Mounting and Grouting
NOTE: After the concrete has cured completely and the
cast-in-place method was used, refer to Figure 20 and
proceed to step 7. If acrylic adhesive anchors are desired, refer to Figure 19 and proceed with step 1 after
concrete has cured completely.
1. Refer to Table 18 to set the drill depth gauge.
2. Drill the holes to the set depth.
3. Use compressed air or squeeze bulb to clean out debris from
each hole.
4. Fill half the hole depth with an industry-accepted adhesive anchoring system.
5. Insert anchor bolt until it reaches the bottom. Refer to Table
18 .
6. Ensure all air pockets are removed from adhesive surrounding
the bolt.
7. Allow adhesive around bolt to cure completely.
8. Remove shipping materials and place the machine or elevated
base frame carefully over the bolts.
NOTE: Never attempt to lift the machine by the door
handle or by pushing on the cover panels. Always
insert a pry bar or other lifting device under the bottom frame of the machine to move it.
IMPORTANT: DO NOT install 80 pound or larger machines on an elevated metal base frame.
9. Raise and level the machine or elevated base frame 0.5 inch
[1.27 cm] off the floor on four corners, using spacers such as
nut fasteners.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
WARNING
Crush hazard. To avoid personal injury and/or
property damage, do not tip the machine more
than 25 degrees in any direction.
W793
10. Completely fill the space between the elevated base frame or
machine base and the floor with a good quality non-shrinking machinery precision grout to ensure a stable installation.
Grout completely under frame. Remove front panel and back
panel to gain access to entire perimeter of base plates. Force
grout under base until all voids are filled.
IMPORTANT: Minimum Grade 5, SAE rating, flat
washers and minimum Grade 5, SAE rating, serrated
hex flange locknuts are the recommended hardware
for anchoring machine or elevated base frame to anchor bolts.
11. Position the flat washers and locknuts on the anchor bolts and
finger-tighten to machine base or elevated base frame.
12. Allow machine grout to set, but not cure.
IMPORTANT: Refer to bolt manufacturer’s recommended adhesive cure times.
13. Remove the spacers carefully, allowing the machine base or
elevated base frame to settle into the wet grout.
NOTE: If installing a 20 through 60 pound model directly to finished floor, wait until grout is completely
cured and skip to Step 18. If installing on elevated
base frame, proceed to Step 14.
20-60 Pound Models
14. After the grout is completely cured, position the machine over
the elevated base frame.
15. Align the mounting holes on the machine with the corresponding holes on the elevated base frame.
16. Install a bolt, flat washer and locknut in each mounting hole.
41
Part No. F8429301ENR15
Installation
17. Hand tighten each nut.
a. Tighten the two rear nuts two turns.
b. Tighten the two front nuts two turns.
c. Tighten the two middle nuts firmly.
18. Torque all the locknuts to 90 ± 9 ft.-lbs. – one after the other
– until all are tightened evenly and the machine is fastened securely to the elevated base frame or floor.
80 Pound and Larger Models
19. After the grout is completely cured, torque the locknuts to 150
± 15 ft.-lbs. – one after the other – until all are tightened evenly and the machine is fastened securely to the floor.
IMPORTANT: Refer to recommended grout cure
times from manufacturer before torquing locknuts.
NOTE: Check and retighten the locknuts after five to
ten days of operation and every month thereafter.
Acrylic Adhesive Anchors (refer to Table 18 )
B
C
1
2
3
A
4
D
5
7
E
6
PHM811N_SVG
1.
2.
3.
4.
5.
6.
7.
Machine Frame Base
Grout 0.5 in. [13 mm]
Acrylic Adhesive
Anchor Bolt (minimum Grade 5 SAE rating)
Concrete
Drill Hole Size per Manufacturer Requirements
Edge of Pad
Figure 19
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
42
Part No. F8429301ENR15
Installation
Cast-in-place Anchors (refer to Table 18 )
B
C
1
2
A
3
D
4
5
1.
2.
3.
4.
5.
E
CHM2438N_SVG
Machine Frame Base
Grout
Anchor Bolt (minimum Grade 5 SAE rating)
Concrete
Edge of Pad
Figure 20
Minimum Anchoring Specifications, in. [mm]
Description
20-40
60
80-100
Number of Bolts
4 or 6*
6
6
A
Bolt Length
6 [152]
6 [152]
8.75 [216]
B
Thread Extension
2.5 [64]
2.5 [64]
2.75 [64]
C
Bolt Diameter
5/8 [16]
5/8 [16]
3/4 [19]
D
Embedment Depth
3.5 [89]
3.5 [89]
6 [152]
E
Distance from Bolt Center to Edge of
Concrete Pad
Refer to Table 8
Refer to Table 8
Refer to Table 11
* On 20-40 pound models, the four (4) corner bolts are required and the two (2) center bolts are optional when mounting a machine
or elevated base frame to floor.
Table 18
Floor Load Data
Specification
Static floor load, lbs. [kN]
20
420 [1.87]
Static pressure, lbs.-ft2 [kN-m2] 96 [4.60]
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
30
40
60
80
100
570 [2.54]
700 [3.11]
940 [4.18]
1550 [6.89]
1670 [7.51]
99 [4.74]
100 [4.79]
106 [5.08]
137 [6.56]
147 [7.04]
43
Part No. F8429301ENR15
Installation
Floor Load Data
Specification
20
30
40
60
80
100
Dynamic floor load, lbs. [kN]
420 [1.86]
630 [2.80]
840 [3.74]
1260 [5.61]
1680 [7.48]
1680 [7.48]
Dynamic floor pressure, lbs.ft2 [kN-m2]
96 [4.60]
109 [5.22]
119 [5.70]
143 [6.85]
149 [7.13]
149 [7.13]
Dynamic load
frequency, Hz
F-speed
9.7
9.0
8.6
8.1
7.4
7.4
V-speed
13.7
12.8
12.2
11.4
10.4
9.5
Maximum moment about machine base, lbs.-ft. [kN-m]
805 [1.09]
1260 [1.71]
1820 [2.47]
2770 [3.76]
4330 [5.87]
4330 [5.87]
Maximum vertical load, lbs.
[kN]
795 [3.54]
1150 [5.12]
1470 [6.54]
2080 [9.25]
3050 [13.57]
3140 [13.82]
N/A = Not Applicable
Table 19
Drain Connection
IMPORTANT: Machine must be installed in accordance
with all local codes and ordinances.
All drain systems must be vented to prevent an air lock or siphoning.
40 PVC plumbing (20 and 30 models) and the 3 inches [76
mm]schedule 40 PVC plumbing (40-100 models).
If proper drain size is not available or practical, a surge tank is
required. A surge tank along with a sump pump should be used
when gravity drainage is not possible.
Use the supplied black rubber adapter and clamps to transition
from the machine drain outlet to the 2 inches [51 mm] schedule
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
44
Part No. F8429301ENR15
Installation
Drain Trough System
1
2
3
7
5
6
4
CHM2379N_SVG
1.
2.
3.
4.
5.
6.
7.
Rear of Machine
Drain Pipe
Steel Grate
Drain Trough
Strainer
Waste Line
1 in. [25 mm] minimum gap
Figure 21
Direct Drain System
4
5*
3
2
1
6
CHM2386N_SVG
* Drain line must be vented to meet local plumbing codes.
1.
2.
3.
4.
5.
6.
Drain Hose
Drain Valve
Drain Tee
Overflow Hose
Vent Pipe*
Trap (as required by local codes)
Figure 22
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
45
Part No. F8429301ENR15
Installation
IMPORTANT: Increasing the drain hose length, installing elbows, or causing bends will decrease drain flow
rates and increase drain times, impairing machine performance.
NOTE: Installation of additional machines will require
larger drain connections. Refer to Drain Line Sizing /
Minimum Drain ID .
Drain Information
Specification
20
30
40
60
80
100
Drain connection size, in. [mm]
2 [51]
2 [51]
3 [76]*
3 [76]*
3 [76]*
3 [76]*
Overflow drain connection size,
in. [mm]
1.5 [457]
1.5 [457]
1.5 [457]
1.5 [457]
2.25 [686]
2.25 [686]
Number of drain outlets
1
1
1
1
1
1
Drain flow capacity, gal/min
[l/min]
25 [95]
30 [114]
40 [151]
50 [189]
55 [208]
55 [208]
Recommended drain pit size, ft3
[l]
2.0 [57]
2.5 [71]
3.5 [128]
5.7 [99]
8.0 [221]
9.5 [269]
* Also works with 3 in. [76 mm] OD PVC pipe if connected to inside of drain tee connector.
Table 20
Drain Line Sizing / Minimum Drain ID, in. [mm]
Number of Machines
Model
1
2
3
4
5
20
2 [50]
3 [76]
3 [76]
4 [102]
4 [102]
30
2 [50]
3 [76]
3 [76]
4 [102]
4 [102]
40
3 [76]
4 [102]
4 [102]
4 [102]
6 [152]
60
3 [76]
4 [102]
4 [102]
4 [102]
6 [152]
80-100
3 [76]
6 [152]
6 [152]
8 [203]
8 [203]
Table 21
perature for on-premises models is 150°F [66°C] (standard models) or 140°F [60°C] (WRAS approved models) .
Water Connection Requirements
Connections should be supplied by a hot and a cold water line of
at least the sizes shown in Water Supply Line Sizing . Installation
of additional machines will require proportionately larger water
lines.
WARNING
To prevent personal injury, avoid contact with inlet
water temperatures higher than 125° Fahrenheit [51°
Celsius] and hot surfaces.
W748
The maximum water inlet temperature for vended models is
125°F [51°C]and the recommended maximum water inlet tem© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Connections should be supplied by a hot and a cold water line per
national and local codes and in accordance with AS/NZS 3500.I.
To connect water service to a machine with hoses, use the following procedure:
1. Before installing hoses, flush the building’s water system at
the machine connection valves for at least two (2) minutes.
46
Part No. F8429301ENR15
Installation
2. Check filters in the machine’s inlet hoses for proper fit and
cleanliness before connecting.
3. Hang hoses in a large loop; do not allow them to kink.
If additional hose lengths are needed or using hoses other than
those supplied by manufacturer, flexible hoses with screen filters
are required.
Cabinet Hardmount Water Supply Information
Specification
Requirement
Model
Water Inlet Connection size,
in. BSP [mm]
20-100
3/4 [19]
Thread pitch, GHT [BSPP]
20-100
3/4 x 11.5 [3/4
x 14]
Number of water inlets
20-100
2
Number of auxiliary water inlets
80-100
(standard
models)
2
Alliance Laundry Systems, LLC ranges of front loading commercial clothes washing machines have solenoid valves at the inlets.
The water supply to the washing machines is supplied with an
AB air gap between the soap tray and the drum. Minimum and
maximum working pressure 1.4 bar and 8.3 bar. The machines
are supplied with approved inlet hoses with a maximum inlet dimension of 0.50 inch [15 mm] (ID).
NOTE: This machine has a fluid category 5 backflow
prevention device built in between the soap tray and
drum.
2
3
4
80-100
0
(WRAS- approved models)
5
Recommended pressure, psi
[bar]
20-100
20-85
[1.4-5.7]
Inlet flow capacity per inlet,
gal/min at 85 psi [l/min at 5.5
bar]
20-100
5.2 [20]
80-100
(auxillary
water inlets)
4.0 [15]
PHM831N_SVG
1.
2.
3.
4.
5.
Table 22
Air Cushions (Risers)
Water Supply Faucets
Dual Check Valves
Filters
Hoses
Figure 23
Water Supply Line Sizing, in. [mm]
Supply Line Size
Number of Machines
1
Main
Hot/Cold
1
.75 [19]
.75 [19]
2
1 [25]
.75 [19]
3
1.25 [32]
1 [25]
4
1.5 [38]
1 [25]
To comply with WRAS (IRN R150) and Australian water regulations, European standard EN1717 and Australian standard
ATS5200.101, an approved double check valve backflow prevention device with the watermark is provided with the unit and must
be fitted at the point of connection(s) between the supply and the
fitting. Refer to Figure 23 .
NOTE: No more than two (2) water connection hoses
should be used on WRAS-approved models.
Table 23
Suitable air cushions (risers) should be installed in supply lines to
prevent “hammering.” Refer to Figure 23 .
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Figure 24
47
Part No. F8429301ENR15
Installation
on the serial plate on the rear of the machine, using copper conductors only.
IMPORTANT: Alliance Laundry Systems warranty does
not cover components that fail as a result of improper
input voltage.
Make sure the correct transformer jumper (208 Volt or 240 Volt)
is in place. Refer to the “optional” Electrical Service Conversion
label located on the back of the machine near the serial plate. Refer to Figure 26 .
Figure 25
1
Electrical Installation Requirements
IMPORTANT: Electrical ratings are subject to change.
Refer to serial plate for electrical ratings information
specific to your machine.
DANGER
Electrical shock hazard will result in death or serious
injury. Disconnect electric power and wait five (5) minutes before servicing.
CHM2436N_SVG
W810
1. Electrical Service Conversion Label
WARNING
Figure 26
Dangerous voltages are present inside the machine.
Only qualified personnel should attempt adjustments
and troubleshooting. Disconnect power from the machine before removing any cover and guards, and
before attempting any service procedures.
Machines are equipped with an AC inverter drives requiring a
clean power supply, free from voltage spikes and surges. Use
voltage monitor to check incoming power.
W736
WARNING
Hazardous Voltage. Can cause shock, burn or death.
Verify that a ground wire from a proven earth ground
is connected to the lug near the input power block
on this machine.
W360
NOTE: For voltages above or below listed specification, a qualified electrical contractor must be consulted
to install the appropriate transformer to meet the OEM
electrical specifications. Refer to North American Approval and CE Approval.
Electrical connections are made at the rear of the machine. The
machine must be connected to the proper electrical supply shown
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
48
Part No. F8429301ENR15
Installation
Input Power Conditioning
install one of the devices listed under the Possible Corrective Action(s).
The drive is suitable for direct connection to input power within
the rated voltage of the drive. Listed in Input Power Condition
are certain input power conditions which may cause component
damage or reduction in product life. If any of the conditions exist,
IMPORTANT: Only one device per branch circuit is required. It should be mounted closest to the branch and
sized to handle the total current of the branch circuit.
Input Power Condition
Possible Corrective Action(s)
Low Line impedance (less than 1% line reactance)
Greater than 120 kVA supply transformer
Line has power factor correction capacitors
Line has frequent power interruptions
•
•
Install Line Reactor
Isolation Transformer
•
•
Install Line Reactor
Isolation Transformer
•
•
Remove MOV jumper to ground
Install Isolation Transformer with grounded secondary (if
necessary)
•
Install Line Reactor
Line has intermittent noise spikes in excess of 6000V (lightning)
Phase to ground voltage exceeds 125% of normal line to line
voltage
Ungrounded distribution system
240V open delta configuration (stinger leg)*
* For drives applied on an open delta with a middle phase grounded neutral system, the phase opposite the phase that is tapped in the
middle to the neutral or earth is referred to as the “stinger leg,” “high leg,” “red leg,” etc. This leg should be identified throughout
the system with red or orange tape on the wire at each connection point. The stinger leg should be connected to the center Phase B
on the reactor.
Table 24
Input Voltage Requirements
DANGER
For voltages above or below listed specifications, contact your
power company or local electrician.
Hazardous Rotation Speed. Will cause serious injury
when controlling AC inverter drive with a parameter
unit, safety features are bypassed allowing basket to
rotate at high speeds with the door open. Place large
sign on front of machine to warn people of imminent
danger.
If machine is intended for four-wire service, a neutral leg must be
provided by power company.
If a delta supply system is used on a four-wire model, connect
high leg to L3.
IMPORTANT: Improper connections will result in equipment damage and will void warranty.
W361
Circuit Breakers and Quick Disconnects
DANGER
Electrical shock hazard will result in death or serious
injury. Disconnect electric power and wait five (5) minutes before servicing.
W810
Single-phase machines require a single-phase inverse-time circuit
breaker. Three-phase machines and V-speed machines require a
separate, three-phase inverse-time circuit breaker to prevent damage to the motor by disconnecting all legs if one should be lost
accidentally. Refer to North American Approval section for model-specific circuit breaker requirements.
IMPORTANT: All quick disconnects should comply
with the specifications. DO NOT use fuses instead of
circuit breakers.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
49
Part No. F8429301ENR15
Installation
Connection Specifications
2
3
IMPORTANT: Connection must be made by a qualified
electrician using wiring diagram provided with machine, or according to accepted European Union standards.
1
Connect machine to an individual branch circuit not shared with
lighting or other equipment. Shield connection in a liquid-tight or
approved flexible conduit. Copper conductors of correct size
must be installed in accordance with National Electric Code
(NEC) or other applicable codes.
4
Use wire sizes indicated in the Electrical Specifications chart for
runs up to 50 feet [15 m]. Use next larger size for runs of 50 to
100 feet [15 to 30 m]. Use two sizes larger for runs greater than
100 feet [30 m].
CHM2407N_SVG
1.
2.
3.
4.
Single-Phase Connections
L1
L2
L3
Ground
For single-phase input, connect L1, L2 and Ground and cap neutral as shown in Figure 27 .
1
Figure 28
2
Grounding
For personal safety and proper operation, the machine must be
grounded in accordance with state and local codes. If such codes
are not available, grounding must conform to the National Electric Code, article 250 (current edition). The ground connection
must be made to a proven earth ground, not to conduit or water
pipes.
4
3
1.
2.
3.
4.
WARNING
CHM2425N_SVG
L1
L2
Ground
Neutral [capped]
Electrically heated machines DO NOT require dual
power sources. Do not connect customer power or
customer load to the Internal Load Distribution terminal block. Refer to the machine electrical schematic for details.
Figure 27
W759
Three-Phase Connections
For three-phase input, connect L1, L2, L3 and Ground as shown
in Figure 28 .
IMPORTANT: If a stinger leg is used for three-phase input, it MUST be connected to L3.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
50
Part No. F8429301ENR15
Installation
Machines with Electric Heat
2
3
CHASIS
L1
L2
L3
TB1
SERVICE
GROUND
1
CHM2380N_SVG
1. Grounding Lug: Connect to proven earth ground
2. Customer Input Power Terminals
3. Internal Load Distribution - DO NOT connect customer
power source or load.
Figure 29
Machines without Electric Heat
2
CHASIS
1
TB1
SERVICE
GROUND
CHM2381N_SVG
1. Grounding Lug: Connect to proven earth ground
2. Customer Input Power Terminals
Figure 30
Machines can be converted for lower voltage operation and/or 50
Hz operation. Refer to conversion label by serial plate for details.
Phase Adder
IMPORTANT: Do not use a phase adder on any machine.
Thermal Overload Protector
For V-speed machines, the inverter drive provides overload protection for the drive motor.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
51
Part No. F8429301ENR15
Installation
North American Approval
20 Pound Capacity Models (North American Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
AWG
mm2
F and V-Speed Models (unless otherwise noted)
B (F-speed)
120
60
1
2
7
15
14
2.5
B (V-speed)
120
60
1
2
8
15
14
2.5
X
200-208
50/60
1/3
2/3
4/3
15
14
2.5
50/60
3
3
3
15
14
2.5
21
30
10
6.0
220-240
Q
Standard
200-208
Electric
Heat
220-240
N
P
Standard
440–480
50/60
3
3
2
15
14
2.5
380–415
50/60
3
3
2
15
14
2.5
13
15
14
2.5
Electric
Heat
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 25
30 Pound Capacity Models (North American Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Wire
Full
Load
Amps
Circuit
Breaker
AWG
mm2
F and V-Speed Models (unless otherwise noted)
B
120
60
1
2
16
20
12
4
X (F-speed)
200–208
50/60
1/3
2/3
5/4
15
14
2.5
50/60
1/3
2/3
6/4
15
14
2.5
220-240
X (V-speed)
200-208
220-240
Table 26 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
52
Part No. F8429301ENR15
Installation
30 Pound Capacity Models (North American Approval)
Voltage Designation
Code
Q
Standard
200–208
Electric
Heat
220-240
N
P
Voltage
Standard
Specifications
Cycle
50/60
Phase
3
Full
Load
Amps
Wire
3
Circuit
Breaker
AWG
mm2
4
15
14
2.5
22
30
10
6.0
440–480
50/60
3
3
3
15
14
2.5
380–415
50/60
3
3
3
15
14
2.5
13
15
14
2.5
Electric
Heat
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 26
40 Pound Capacity Models (North American Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
AWG
mm2
F and V-Speed Models (unless otherwise noted)
B
120
60
1
2
16
20
12
4
X (F-speed)
200–208
50/60
1/3
2/3
6/4
15
14
2.5
50/60
1/3
2/3
7/4
15
14
2.5
50/60
3
3
4
15
14
2.5
42
50
8
10.0
3
15
14
2.5
22
30
10
6.0
220-240
X (V-speed)
200–208
220-240
Q
N
Standard
200-208
Electric
Heat
220-240
Standard
440-480
50/60
3
3
Electric
Heat
Table 27 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
53
Part No. F8429301ENR15
Installation
40 Pound Capacity Models (North American Approval)
Voltage Designation
Code
P
Standard
Voltage
380–415
Specifications
Cycle
50/60
Phase
3
Full
Load
Amps
Wire
3
Electric
Heat
Circuit
Breaker
AWG
mm2
3
15
14
2.5
25
30
10
6.0
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 27
60 Pound Capacity Models (North American Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
AWG
mm2
F and V-Speed Models (unless otherwise noted)
X (F-speed)
200–208
50/60
1/3
2/3
9/6
15
14
2.5
50/60
1/3
2/3
10/6
15
14
2.5
50/60
3
3
6
15
14
2.5
43
50
8
10.0
4
15
14
2.5
22
30
10
6.0
4
15
14
2.5
25
30
10
6.0
220-240
X (V-speed)
200-208
220-240
Q
N
Standard
200-208
Electric
Heat
220-240
Standard
440-480
50/60
3
3
Electric
Heat
P
Standard
380-415
50/60
3
3
Electric
Heat
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 28
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
54
Part No. F8429301ENR15
Installation
80 Pound Capacity Models (North American Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
AWG
mm2
F-Speed Models
X
200–208
50/60
1/3
2/3
12/8
15
14
2.5
50/60
3
3
8
15
14
2.5
72
80
4
25.0
5
15
14
2.5
37
40
8
10.0
5
15
14
2.5
33
40
8
10.0
220-240
Q
N
Standard
200-208
Electric
Heat
220-240
Standard
440-480
50/60
3
3
Electric
Heat
P
Standard
380-415
50/60
3
3
Electric
Heat
V-Speed Models
X
200-208
50/60
1/3
2/3
15/9
20/15
12/14
4/2.5
50/60
3
3
9
15
14
2.5
72
80
4
25.0
6
15
14
2.5
37
40
8
10.0
6
15
14
2.5
33
40
8
10.0
220-240
Q
N
Standard
200-208
Electric
Heat
220-240
Standard
440-480
50/60
3
3
Electric
Heat
P
Standard
380-415
50/60
3
3
Electric
Heat
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 29
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
55
Part No. F8429301ENR15
Installation
100 Pound Capacity Models (North American Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
AWG
mm2
F-Speed Models
X
200-208
50/60
1/3
2/3
16/9
20/15
12/14
4/2.5
50/60
3
3
9
15
14
2.5
74
80
4
25.0
6
15
14
2.5
37
40
8
10.0
6
15
14
2.5
34
40
8
10.0
220-240
Q
N
Standard
200-208
Electric
Heat
220-240
Standard
440-480
50/60
3
3
Electric
Heat
P
Standard
380-415
50/60
3
3
Electric
Heat
V-Speed Models
X
200-208
50/60
1/3
2/3
16/10
20/15
12/14
4/2.5
50/60
3
3
10
15
14
2.5
74
80
4
25.0
7
15
14
2.5
37
40
8
10.0
7
15
14
2.5
34
40
8
10.0
220-240
Q
N
Standard
200-208
Electric
Heat
220-240
Standard
440-480
50/60
3
3
Electric
Heat
P
Standard
380-415
50/60
3
3
Electric
Heat
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 30
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
56
Part No. F8429301ENR15
Installation
CE Approval
20 Pound Capacity Models (CE Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
mm2
F and V-Speed Models
N
440-480
50/60
3
3
2
6
2.5
X
200–208
50/60
1/3
2/3
4/3
6
2.5
50/60
3
3
3
6
2.5
21
25
2.5
2
6
2.5
13
16
2.5
220-240
Q
Standard
200–208
Electric Heat 220-240
P
Standard
380–415
50/60
3
3
Electric Heat
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 31
30 Pound Capacity Models (CE Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
mm2
F and V-Speed Models (unless otherwise noted)
N
440-480
50/60
3
3
3
6
2.5
X (F-speed)
200–208
50/60
1/3
2/3
5/4
6
2.5
50/60
1/3
2/3
7/4
10/6
2.5
50/60
3
3
4
6
2.5
22
25
2.5
3
6
2.5
13
16
2.5
220-240
X (V-speed)
200–208
220-240
Q
Standard
200-208
Electric Heat 220-240
P
Standard
380–415
50/60
3
3
Electric Heat
Table 32 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
57
Part No. F8429301ENR15
Installation
30 Pound Capacity Models (CE Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
mm2
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 32
40 Pound Capacity Models (CE Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
mm2
F and V-Speed Models (unless otherwise noted)
N
Standard
440-480
50/60
3
3
Electric Heat
X
200–208
3
6
2.5
22
25
2.5
50/60
1/3
2/3
7/4
10/6
2.5
50/60
3
3
4
6
2.5
42
50
10.0
3
6
2.5
26
32
2.5
3
6
2.5
26
32
2.5
220-240
Q
Standard
200–208
Electric Heat 220-240
P (F-Speed)
Standard
380-415
50/60
3
3
Electric Heat
P (V-Speed)
Standard
380-415
50/60
3
3
Electric Heat
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 33
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
58
Part No. F8429301ENR15
Installation
60 Pound Capacity Models (CE Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
mm2
F and V-Speed Models (unless otherwise noted)
N
Standard
440-480
50/60
3
3
Electric Heat
X
200–208
4
6
2.5
22
25
2.5
50/60
1/3
2/3
11/7
16/10
2.5
50/60
3
3
7
10
2.5
43
50
10.0
4
6
2.5
26
32
2.5
4
6
2.5
26
32
2.5
220-240
Q
Standard
200–208
Electric Heat 220-240
P (F-Speed)
Standard
380-415
50/60
3
3
Electric Heat
P (V-Speed)
Standard
380-415
50/60
3
3
Electric Heat
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 34
80 Pound Capacity Models (CE Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
mm2
F-Speed Models
N
Standard
440-480
50/60
3
3
Electric Heat
X
200–208
7
10
2.5
37
40
4.0
50/60
1/3
2/3
12/8
16/10
2.5
50/60
3
3
8
10
2.5
72
80
16.0
220-240
Q
Standard
200–208
Electric Heat 220-240
Table 35 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
59
Part No. F8429301ENR15
Installation
80 Pound Capacity Models (CE Approval)
Voltage Designation
Code
P
Voltage
Standard
380-415
Specifications
Cycle
50/60
Phase
3
Full
Load
Amps
Wire
3
Electric Heat
Circuit
Breaker
mm2
7
10
2.5
33
40
4.0
7
10
2.5
37
40
4.0
V-Speed Models
N
Standard
440-480
50/60
3
3
Electric Heat
X
200–208
50/60
1/3
2/3
17/11
20/16
2.5
50/60
3
3
11
16
2.5
72
80
16.0
7
10
2.5
33
40
4.0
220-240
Q
Standard
200–208
Electric Heat 220-240
P
Standard
380-415
50/60
3
3
Electric Heat
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 35
100 Pound Capacity Models (CE Approval)
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Circuit
Breaker
mm2
F and V-Speed Models
N
Standard
440-480
50/60
3
3
Electric Heat
X
200–208
7
10
2.5
38
40
4.0
50/60
1/3
2/3
17/11
20/16
2.5
50/60
3
3
11
16
2.5
74
80
16.0
220-240
Q
Standard
200–208
Electric Heat 220-240
Table 36 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
60
Part No. F8429301ENR15
Installation
100 Pound Capacity Models (CE Approval)
Voltage Designation
Code
P
Voltage
Standard
380-415
Specifications
Cycle
50/60
Phase
3
Full
Load
Amps
Wire
3
Electric Heat
Circuit
Breaker
mm2
7
10
2.5
34
40
4.0
NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310.
Table 36
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
61
Part No. F8429301ENR15
Installation
Steam Requirements (Steam Heat Option Only)
Supply Dispensing
WARNING
Hot Surfaces. Will cause severe burns. Turn steam
off and allow steam pipes, connections and components to cool before touching.
W505
For machines equipped with optional steam heat, install piping in
accordance with approved commercial steam practices. Steam requirements are shown in Table 37 .
Steam Supply Information
Steam inlet connec- 40–100 pound*
tion size, in. [mm]
1/2 [13]
Number of steam inlets
1
80 [5.4]
* 20 and 30 pound models can be prep for steam and a kit is
available for conversion.
Table 37
IMPORTANT: Failure to install the customer supplied
steam filter may void the warranty.
Supply Dispensing
Number of external liquid supply connections
5
Liquid supply connection size, in. [mm]
3/8 [8]
Table 38
IMPORTANT: Undiluted chemical dripping can damage
the machine. All chemical injection supply dispenser
pumps and dispenser tubing should be mounted below
the washer’s injection point. Loops do not prevent
drips if these instructions are not followed.
IMPORTANT: Failure to follow these instructions could
damage the machine and void the warranty.
For proper communication between the machine and an external
chemical supply system, it is important for the low-voltage signal
power to be connected properly. The included wiring diagram
shows several different options for safe and correct wiring of this
interface.
The preferred method for connecting the wiring from the external
chemical supply system to the machine is to use the 300mA power of the machine’s 24VAC control transformer, which is intended strictly for this purpose. Other voltage and current options
are available, but require some wiring changes and must be provided with an external power source. Under no circumstances
should the high-voltage machine supply connections or source be
used for the communication wiring.
Communication wiring connections, which include a single row
of identified terminal blocks, can be found under a service panel
at the upper back of the machine.
WARNING
Dangerous Chemicals. May damage eyes and skin.
Wear eye and hand protection when handling chemicals; always avoid direct contact with raw chemicals.
Read the manufacturer’s directions for accidental
contact before handling chemicals. Ensure an eyerinse facility and an emergency shower are within
easy reach. Check at regular intervals for chemical
leaks.
Chemical Injection Using Internal 24VAC Control
Transformer
NOTE: Using the Internal 24VAC 300 Milliamp Control
Transformer is recommended by Alliance Laundry Systems.
CAUTION
Do not attempt to increase fuse rating or alter wiring
of external chemical supply terminal strip in such as
way that may conflict with the suggested methods
provided on the Optional External Supply Wiring Diagram.
W363
Supply Dispensing
Number of liquid chemical supply signals
(OPL only)
4
External Supplies
Required pressure, (min. - max. psi [bar]) 30–80 [2.0–5.4]
Maximum pressure, psi [bar]
Number of supply compartments
4
W699
Table 38 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
62
Part No. F8429301ENR15
Installation
IMPORTANT: DO NOT remove the red jumper wire from
the terminal strip.
There are 3 terminals necessary for this connection option.
•
1
•
EXTERNAL DISPENSER CONNECTIONS
ES 1
EXAMPLE FOR EXTERNAL
DISPENSER CONNECTION
ES 2
ES 3
ES 4
RELAY COM
Supply 1
External
Dispensing
System
RELAY
COM
24VAC COM
IMPORTANT: Do not use the transformer terminals if
an external power supply is used.
RED
24VAC
24VAC COM
Terminal “24VAC COM” is used to connect one side of the
internal control transformer to the external dispenser input
signals common.
The second terminal is used to connect the other side of the
control transformer to the machine output signals common
through a red jumper wire between “24VAC” and “RELAY
COM”. Refer to Figure 32 .
Internal
Supply
300mA Max
JUMPER FOR INTERNAL
24 VAC SUPPLY
CONNECTED TO RELAY
COM. (REMOVE IF NOT
WIRING TO INTERNAL
24 VAC SUPPLY
2
STEP 1: Insert screwdriver & press down
to open cage clamp.
STEP 2: Insert Wire
Wire Size 28-16AWG
0.08-1.5mm
8.5mm
Strip Length
3
4
CHM2336N_SVG
1.
2.
3.
4.
Relay Com
Red Jumper Wire
24 VAC
Transformer
Figure 31
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
63
Part No. F8429301ENR15
Installation
3
2
4
1
5
6
7
= Neutral
= Power
PHM821N_SVG
1.
2.
3.
4.
5.
6.
7.
External Supply Power Output
Internal Control Transformer
RELAY COM Terminal
External Dispenser Input Signal Common
Red Jumper Wire
24VAC Terminal
24VAC COM Terminal
Figure 32
Chemical Injection Using External AC Power Source
NOTE: An External AC Power Source is NOT provided
by Alliance Laundry Systems.
NOTE: Power for external supplies must not be derived
from the high-voltage main power connection point.
1. Remove the red jumper wire installed by the factory between
“24VAC”, and “RELAY COM”.
2. Connect one side of the external power to the “RELAY
COM” and the other to the external dispenser input signals
common. Refer to Figure 33 .
IMPORTANT: The external power must supply power of
240VAC or less and be protected at 3 Amps or less.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
64
Part No. F8429301ENR15
Installation
3
1
4
2
= Neutral
= Power
5
PHM823N_SVG
1.
2.
3.
4.
5.
External Supply Power Output
Red Jumper Wire
External Supply Input Signal Common
VAC Power Terminal
VAC RETURN Terminal
Figure 33
External Supply Signals
CAUTION
Do not attempt to increase fuse rating or alter wiring
of external chemical supply terminal strip in such as
way that may conflict with the suggested methods
provided on the Optional External Supply Wiring Diagram.
W699
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Wash-cycle signals are provided to the external chemical supply
equipment and a “wait for the next step” signal can be received
from the supply equipment.
For example, if ES1 is selected the K1 contact will close and
power will be supplied to Supply 1 Signal. The contact will remain closed for the amount of time programmed in control. Refer
to Figure 34 for Internal Supply Connection or Figure 35 for External AC Connection.
65
Part No. F8429301ENR15
Installation
3
= Neutral
= Power
1
2
PHM822N_SVG
1. ES1 Power supply
2. K1 Contact
3. Supply 1 Signal
Figure 34
3
= Neutral
= Power
1
2
PHM824N_SVG
1. ES1 Power supply
2. K1 Contact
3. Supply 1 Signal
Figure 35
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
66
Part No. F8429301ENR15
Installation
Connection of External Liquid Supplies
OPL Models
1. Facing the rear of the machine, locate the five (5) 3/8 inch [10
mm] supply hose connections found on the right-hand side of
the valve panel. Refer to Figure 36 .
Valve Panel-Rear View
1
CHM2388N_SVG
1. External Supply Hose Opening
Figure 36
2. Drill through the five (5) plastic holes on the valve panel for
the external supply hoses as needed.
3. Remove plastic debris.
4. Attach the external supply hoses to the ports at each of the
drilled holes.
5. Secure with proper clamps.
NOTE: Do not attempt to make chemical injection supply pump electrical connections to points other than
those provided specifically for that purpose by the factory.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
67
Part No. F8429301ENR15
Start Up
Start Up
Pallet Jack cover Plate Installation (80
and 100 Pound Models Only)
After machine is fully installed, the optional pallet jack cover
plate can be installed.
1. Locate the two holes on the front of the machine base frame.
Refer to Figure 37 .
4
1
3
2
1
CHM2392N_SVG
1.
2.
3.
4.
Nut
Cover Plate
Stud
Machine Base Frame
Figure 37
2. Using the hardware from removing plate from back panel, install the cover plate to the machine base frame. The square on
stud goes into square hole in machine frame. Refer to Figure
37 .
Basket Rotation
Check that basket rotation is counterclockwise in the extract step.
1. If rotation is not counterclockwise, disconnect power to machine.
2. Have a qualified electrician reverse any two motor leads at
the inverter terminal block.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
68
Part No. F8429301ENR15
Operation
Operation
Operating Instructions
5. The default wash cycle will display.
WARNING
1. Turn on main power source (circuit breaker).
2. Turn handle clockwise to open. Refer to Figure 38 .
To prevent personal injury, avoid contact with inlet
water temperatures higher than 125° Fahrenheit [51°
Celsius] and hot surfaces.
W748
6. Select the desired soil setting (select models only), cycle setting (select models only) and cycle/temperature. The LED indicator(s) for that cycle will light.
CAUTION
CHM2243N_SVG
Water cannot be extracted from rubber backed
items. To avoid damage to machine from out of balance conditions, do not use a spin (extract) step
when washing rubber backed items. Warranty will be
voided.
Figure 38
3. Load to capacity whenever possible. DO NOT OVERLOAD.
Refer to Figure 39 .
NOTE: Underloading can cause out-of-balance conditions that can shorten machine life.
U003I_SVG
Figure 39
4. Close door and turn handle counter clockwise. Refer to Figure 40 .
CHM2244N_SVG
Figure 40
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
W880
7. Add liquid and/or powder supplies to supply dispenser. Refer
to Table 39 .
a. Detergent:
• Liquid - Compartment 1 (prewash) + Compartment 3
• Powder - Compartment 1 (prewash) + Compartment 2
b. Bleach:
• Liquid - Compartment 3
• Powder - Compartment 2
c. Softener:
• Liquid - Compartment 4
8. For vended models only, insert coin(s) or card as necessary.
• If the machine is a coin operated unit, add coins. As each
coin is added, the vend counts down to the amount remaining.
• If the machine is a card operated unit, insert and remove
card per card system instructions.
• If the unit is interfaced to a central/remote pay system, go
to the central/remote pay console, make payment and select the machine and follow central/remote pay system instructions.
9. Press the START keypad.
10. During first fill, the desired wash cycle can be changed. After
first fill has ended, the wash cycle active at that moment remains the chosen wash cycle.
11. When cycle is complete, display shows “00”.
69
Part No. F8429301ENR15
Operation
a. DETERGENT
1
2
CHM2227N_SVG
CHM2228N_SVG
1. Liquid Detergent
2. Powder Detergent
b. BLEACH
3
4
CHM2229N_SVG
3. Liquid Bleach
CHM2230N_SVG
4. Powder Bleach
c. SOFTENER
5
CHM2231N_SVG
5. Liquid Softener
Table 39
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
70
Part No. F8429301ENR15
Maintenance
Maintenance
Maintenance
4. Inspect all chemical inlets, lines and connections for leaks.
WARNING
WARNING
To reduce the risk of electrical shock, serious injury or death, disconnect the electrical power to
washer-extractor before examining the wiring.
Sharp edges can cause personal injury. Wear safety
glasses and gloves, use proper tools and provide
lighting when handling sheet metal parts.
W366R1
IMPORTANT: Replace all panels that are removed to
perform service and maintenance procedures. Do not
operate the machine with missing guards or with broken or missing parts. Do not bypass any safety devices.
Daily
WARNING
Do not spray the machine with water. Short circuiting and serious damage may result.
W782
IMPORTANT: Door lock should be checked daily to ensure proper operation. Also check that all safety and
instruction stickers are on the machine. Any missing or
illegible safety instructions stickers should be replaced
immediately.
Beginning of Day
1. Check door interlock before starting operation:
a. Attempt to start the machine with the door open. The machine should not start.
b. Close the door without locking it and start the machine.
The machine should not start.
c. Attempt to open the door while the cycle is in progress.
The door should not open.
If the door lock and interlock are not functioning properly, disconnect power and call a service technician.
IMPORTANT: Door lock should be checked daily to
ensure proper operation. Also, check that all safety
and instruction stickers are on the machine. Replace as necessary.
2. Inspect water inlet valve hose connections on the back of the
machine for leaks.
3. Inspect steam hose connections for leaks (where applicable).
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
W636
5. Verify that insulation is intact on all external wires and that
all connections are secure. If bare wire is evident, call a service technician.
End of Day
1. Clean the door gasket of residual detergent and all foreign
matter.
2. Clean the door glass with a damp cloth.
3. Clean automatic supply dispenser lid and general area.
4. Clean the machine’s top, front and side panels with mild detergent. Rinse with clean water. DO NOT use products that
contain alcohol on the control panel.
5. Inspect and clean basket.
6. Clean the inverter drive box filter(s) weekly or more frequently as needed (where applicable):
a. Wash the filter with warm water and allow filter to air dry.
As an alternative, the filter may be vacuumed clean.
NOTE: Unload the machine promptly after each completed cycle to prevent moisture buildup. Leave loading door open after each completed cycle to allow
moisture to evaporate.
Weekly
1. Check the machine for leaks.
a. Start an unloaded cycle to fill the machine.
b. Verify that door and door gasket do not leak.
c. Verify that the drain valve is operating and that the drain
system is free from obstruction. If water does not leak out
during the first wash segment, the drain valve is closed
and functioning properly.
2. Clean the inverter drive box filter(s) weekly or more frequently as needed (where applicable):
a. Wash the filter with warm water and allow filter to air dry.
As an alternative, the filter may be vacuumed clean.
71
Part No. F8429301ENR15
Maintenance
IMPORTANT: The control module cover and fan filter
must be in place for the fan to properly cool the inverter drive. Failure to observe this warning will void the
warranty and could lead to expensive inverter drive repair.
3. On machines equipped with an automatic chemical supply
system, check chemical connections by inspecting all connections and chemical hoses for leaks or cracks.
1
2
5
IMPORTANT: Chemical leaks can quickly cause permanent damage to the machine components and structure.
3
4
Monthly
PHM963N_SVG
NOTE: Disconnect power to the machine at its source
before performing the monthly maintenance procedures.
1. Check belt(s) require replacement or adjustment. Call a qualified service technician in either case.
a. Check belt(s) for uneven wear and frayed edges. Belts
must not be twisted and must be properly seated on pulleys.
b. After disconnecting power to the machine and removing
all panels necessary for access to the drive belt, use one of
the following methods to verify that the belt is properly
tensioned.
1.
2.
3.
4.
5.
Figure 41
•
NOTE: Basket pulley must be rotated three (3)
full turns before assessing belt tension after every adjustment.
•
Top Nut
Jam Nut
Spring Length
Spring
Eyebolt
•
Frequency Gauge. Tighten eyebolt top nut until the
correct frequency (refer to Table 42 ) is obtained midspan. Torque jam nut to spring bracket to 20.6 ± 2 ft.lbs. Refer to Figure 41 .
Tension Gauge. Tighten eyebolt top nut until the
proper belt gauge (refer to Table 42 ) is obtained midspan. Torque jam nut to spring bracket to 20.6 ± 2 ft.lbs. Refer to Figure 41 .
Spring Length. Tighten eyebolt top nut until the
spring measures the correct distance between the
hooks. Refer to Table 40 . Torque jam nut to spring
bracket to 20.6 ± 2 ft.-lbs. Refer to Figure 41 .
Spring Length, in. [mm]
Model
Distance Between
Hooks
20 (2 HP)
5 1/8 [130]
30-40
4 3/4 [121]
60
5 1/16 [129]
80-100
4 3/4 [121]
Table 40
•
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
72
Burroughs Gauge (20 pound 1 HP models only).
Use a Burroughs belt gauge to obtain proper tension.
Proper belt tension is obtained when belt can be deflected from normal position (refer to Figure 42 )
when moderate pressure of is applied to the point midway between pulleys.
Part No. F8429301ENR15
Maintenance
Belt Tension by Frequency or Belt Tension
Gauge
Model
1
Frequency (Hz)
Belt Tension
(lbs.)
Tension
Gauge
(N)
20 (1 HP) 95 ± 2
39.6 ± 1.5
176 ± 7
20
98 ± 2
(2 HP)*
70.2 ± 5.6
312 ± 25
30*
99 ± 4
71 ± 5.6
317 ± 25
40*
87 ± 84
70.3 ± 6.3
313 ± 28
60*
87 ± 4
92.7 ± 8.8
413 ± 39
80-100
102 ± 2
132 ± 5
588 ± 23
* Models made before 10/13/14 are self-tensioning and
do not require any adjustment.
CHM2437N_SVG
1. 1/4 inch [6.35 mm] deflection
Table 42
Figure 42
•
Maintain Tension During Belt Removal. If proper
tension is achieved, tape the jam nut in place and loosen eyebolt top nut to release the belt. Replace belt and
retighten eyebolt top nut back to jam nut position. Refer to Figure 41 .
c. Verify allowable distance of belt from edge of basket pulley. Refer to Flat-Pulley Alignment .
Flat-Pulley Alignment, in. [mm]
Model
Minimum Allowable Distance
from Edge
20
.09 [2]
30
.09 [2]
40
.09 [2]
60
.38 [10]
Table 41
2. For 80 through 100 pound capacity models only, lubricate
bearings and seals each month OR after every 200 hours of
operation.
a. Use a premium-grade lithium-based #2 grease. Never mix
two types of grease, such as petroleum and silicone.
b. Pump the grease gun slowly, permitting only 2 strokes for
each bearing grease fitting.
NOTE: Do not pump the grease gun until grease
comes out of the bearing housing. This can result in
over lubrication, causing damage to bearings and
seals.
3. Check overflow hose and drain hose for leaks.
4. Check the supply dispenser hoses and hose connections.
5. Clean inlet hose filter screens:
a. Turn water off and allow valve to cool, if necessary.
b. Unscrew inlet hose and remove filter screen.
c. Clean with soapy water and reinstall. Replace if worn or
damaged.
Quarterly
NOTE: Disconnect power to the machine at its source
before performing the quarterly maintenance procedures.
1. Tighten door hinges and fasteners, if necessary.
2. Tighten anchor bolts, if necessary.
3. Tighten anchor bolts as specified in the Machine Mounting
and Grouting section, if necessary.
4. Verify that the drain motor shield is in place and secure, if so
equipped.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
73
Part No. F8429301ENR15
Maintenance
5. Clean customer-supplied steam filter, where applicable. Refer
to Figure 43 .
a. Turn off steam supply and allow time for the valve to
cool.
b. Unscrew cap.
c. Remove element and clean.
d. Replace element and cap.
1
2
H042I_SVG
1. Cap
2. Steam Filter Element
Figure 43
6. Check the bearing mounting bolts to make sure they are torqued properly. Refer to Torque .
Torque, ft-lbs.
Model
Bearing
Torque
20
All
41
30-40
All
101
60
All
201
80-100
All
357
Table 43
7. Tighten motor mounting bolt locknuts and bearing bolt locknuts.
8. Vacuum lint from motor vents.
9. Clean all electronic boards of moisture and dust with canned
air.
10. Verify the insulation is intact on all external wires and that all
connections are secure. If bare wire is evident, call a service
technician.
11. Clean inverter drive cooling fan blades (where applicable).
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
74
Part No. F8429301ENR15
Maintenance
Care of Stainless Steel
•
•
•
•
•
•
•
•
Remove dirt and grease with detergent and water. Thoroughly
rinse and dry after washing.
Avoid contact with dissimilar metals to prevent galvanic corrosion when salty or acidic solutions are present.
Do not allow salty or acidic solutions to evaporate and dry on
stainless steel. Wipe clean of any residues.
Rub in the direction of the polish lines or “grain” of the stainless steel to avoid scratch marks when using abrasive cleaners. Use stainless steel wool or soft, non-metal bristle brushes.
Do not use ordinary steel wool or steel brushes.
If the stainless steel appears to be rusting, the source of the
rust may be an iron or steel part not made of stainless steel,
such as a nail or screw.
Remove discoloration or heat tint from overheating by scouring with a powder or by employing special chemical solutions.
Do not leave sterilizing solutions on stainless steel equipment
for prolonged periods of time.
When an external chemical supply is used, ensure no siphoning of chemicals occurs when the machine is not in use. Highly concentrated chemicals can cause severe damage to stainless steel and other components within the machine. Damage
of this kind is not covered by the manufacturer’s warranty.
Locate the pump and tubing below the machines’s injection
point to prevent siphoning of chemicals into the machine.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
75
Part No. F8429301ENR15
Disposal of Unit
Disposal of Unit
This appliance is marked according to the European directive
2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE).
This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste. Refer to Figure
44 . Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. Ensuring this product is disposed of correctly will help prevent potential negative consequences for the environment and human
health which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to
conserve natural resources. For more detailed information about
recycling of this product, please contact the local city office,
household waste disposal service, or the source from which the
product was purchased.
MIX1N_SVG
Figure 44
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
76
Part No. F8429301ENR15
Download PDF