Specifications

HFX 100 Tx/Rx

NOTE: The HFX 100 TX/RX consists of a transmitter (HFX 100 TX) and a receiver (HFX 100 RX) with fiber optic cables linking the two units.

NOTE: These devices are class 1 laser products. They meet the safety regulations of IEC-60825, FDA 21 CFR

1040.10, and FDA 21 CFR 1040.11

Optical fiber interconnection between transmitter and receiver

Number/type .................................. 1 fiber optic, multimode (OM3 or OM4 fiber, must use 50/125 µm)

Connectors .................................... 1 LC connector

Operating distance ......................... 300 m

NOTE: Operating distance is approximate. This is a typical maximum distance that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks.

Nominal peak wavelength .............. 850 nm (multimode)

Data rate ........................................ 6.25 Gbps

Transmission power

Multimode ............................... -7 dBm, typical

Maximum receiver sensitivity

Multimode ............................... -19 dBm, typical

Optical loss budget

Multimode ............................... 12 dB, maximum

Video

NOTE: *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.

Resolution range ............................ Up to 1920x1200 or 1080p @ 60 Hz, 2k pixel for pixel @ 12 bit color depth

Formats ......................................... RGB and YCbCr

EDID .............................................. Pass through from Rx unit to Tx unit

HDCP ............................................ Pass through

Standards ...................................... DVI 1.0, HDMI, CEA-861E

Video input — transmitter

Number/signal type ........................ 1 single link HDMI

Connectors .................................... 1 Male HDMI, fixed cable 3.0'

Video output — receiver

Number/signal type ........................ 1 single link HDMI

Connectors .................................... 1 Male HDMI, fixed cable 3.0'

Extron HFX 100 Tx, HFX 100 Rx Fiber Optic DVI Extenders • Specifications 1

THIS TEXT WINDOW and its contents are for reference only. Delete this material before finishing and releasing the specs sheet.

z z

For manuals (guides), use the standard Section style from the current user guide template instead of Chapter title, specs sheet or Heading 1, specs stand-alone; use Heading 1 as usual for “Specifications” if the specs are part of a multitopic chapter.

z z Click the text tool where you want to insert the specs table, select the specs table

container paragraph style, then paste in the specs table from the stand-alone master specs sheet.

z z

For specifications from template v7.6 or earlier, use this guide to which new paragraph style replaces which old style: z z z z z z z z

Specs8_Heading 2 replaces SpecsSubHdr

Specs8_L1 “ Specs7

Specs8_L1 cont’d

Specs8_L2

“

“

Specs7A

Specs7 subcategory z z z z

Specs8_L3

Specs8_Note

“ Specs7 sub-subcategory

“ SpecsNote7 z z z z

Specs8_Warning/Caution “

Specs8_ Revision code “

Specs7Warning/caution

Revision code z z

The other new styles are required for proper table placement/formatting (one for the entire specs table as placed within a manual section [specs table conteiner], two others

[ Specs8_Note L1 table and Specs8_Note L2 table] for the note/caution cells within the specs table). z z

At this time, the notes, cautions, and warnings boxes/tables within specs have to be hand inserted and merged and formatted. Use the existing table styles ( NOTE,

Caution, and Warning1) for the table boxes.

z z z z z z

Apply the Specs8_Note L1 table or Specs8_Note L2 table paragraph style

(depending on the content to which the note, caution, or warning applies) to the nested note, caution, or warning table. Also apply the Specs8_Note cell insets cell style to the cell containing the note, caution, or warning nested table.

Apply the Specs8_Note or Specs8_Warning/Caution paragraph style to the text within the nested note, caution, or warning table.

Apply the Specs8_note cell inset cell style to the specs table cell containing the nested table.

For use with user guides (manuals) only (but NOT for stand-alone specs sheets), two bulleted note styles are available to use when you combine a series of notes into one note table: z z

Specs8_Note_bulleted — This is for the first paragaph, and you have to manually insert the bullet character and second tab.

z z

Specs8_Note_bulleted, cont'd — This is for susequent paragaphs within a note box. The bullet character is automatically inserted.

Here is an example of how those two styles are used:

NOTES: • This is just test text to show the style. You wouldn't normally put completely unrelated topics together in a shared note.

All nominal levels are at ±10%. UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety.

UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety.

• Specifications are subject to change without notice. UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety.

• The 5-pole port supports both hardware and software flow control.

The 3-pole ports support software flow control.

General

Power supply ................................. External

Input: 100-240 VAC, 50-60 Hz

Output: 12 VDC, 1 A, 12 watts

Power consumption

Transmitter .............................. 12 VDC, 220 mA, 2.5 W

Receiver .................................. 12 VDC, 175 mA, 2.1 W

Temperature/humidity .................... Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing

Cooling .......................................... Convection, no vents

Thermal dissipation

Transmitter .............................. 8.0 BTU/Hr

Receiver .................................. 6.8 BTU/Hr

Mounting

Rack mount ............................. Yes, with optional 1U rack shelf

Furniture mount ....................... Yes, with optional ZipClip 200™ or under-desk mounting kit

Pole mount .............................. Yes, with optional pole-mount kit

Enclosure type ............................... Metal

Enclosure dimensions .................... 1.7" H x 2.2" W x 3.0" D (1 U high, one-eigth rack wide)

(4.2 cm H x 5.6 cm W x 7.6 cm D)

(Depth excludes connectors.)

Product weight .............................. 0.5 lbs (0.3 kg)

Shipping weight ............................. 3 lbs (2 kg)

Vibration ........................................ ISTA 1A in carton (International Safe Transit Association)

Regulatory compliance

Safety ...................................... CE, c-UL, UL

EMI/EMC ................................. CE, C-tick, FCC Class A, ICES, KCC, VCCI

Environmental .......................... Complies with the appropriate requirements of RoHS, WEEE

Warranty ........................................ 3 years parts and labor

NOTE: All nominal levels are at ±10%.

NOTE: Specifications are subject to change without notice.

8.1-073114-D6

Extron HFX 100 Tx, HFX 100 Rx Fiber Optic DVI Extenders • Specifications 2