Seagate | ST9120817AS - Momentus 5400.4 120 GB Hard Drive | Technical information | Seagate ST9120817AS - Momentus 5400.4 120 GB Hard Drive Technical information

eMachines D720/D520 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on eMachines D720/D520 Series service guide.
Date
II
Chapter
Updates
Copyright
Copyright © 2008 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
System Specifications
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
TouchPad Basics (with fingerprint reader) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Lock Keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Special Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Acer GridVista (dual-display compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
System Utilities
21
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
BIOS Flash Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
DOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
WinFlash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Remove HDD/BIOS Password Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Machine Disassembly and Replacement
41
Disassembly Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Pre-disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
External Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
External Modules Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Removing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Removing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Removing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Removing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Removing the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Main Unit Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Removing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
VII
Table of Contents
Removing the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Removing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Removing the TouchPad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Removing the Speaker Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Removing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Removing the Modem Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Removing the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Removing the CPU Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Removing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
LCD Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
LCD Module Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Removing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Removing the Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Removing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Removing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Removing the LCD Brackets and FPC Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Removing the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Removing the MIC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
LCD Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Replacing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Replacing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Main Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Replacing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Replacing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Replacing the CPU Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Replacing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Replacing the Modem Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Replacing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Replacing the Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Replacing the TouchPad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Replacing the Upper Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Replacing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Replacing the Antenna Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Replacing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Replacing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Replacing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Replacing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Replacing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Replacing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Replacing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Troubleshooting
107
Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Power On Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
No Display Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Random Loss of BIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
LCD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Built-In Keyboard Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
TouchPad Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Internal Speaker Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Internal Microphone Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
HDD Not Operating Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
VIII
Table of Contents
ODD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Modem Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Wireless Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Thermal Unit Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
External Mouse Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Other Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Post Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Sec: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Memory: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
BDS & Specific action: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Each PEIM entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Each Driver entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Each SmmDriver entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . .128
Jumper and Connector Locations
129
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
Clearing Password Check and BIOS Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Clearing Password Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
BIOS Recovery by Crisis Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
FRU (Field Replaceable Unit) List
133
eMachines D720/D520 Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
eMachines D720/D520 FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
Screw List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
Model Definition and Configuration
142
eMachines D720/D520 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
Model Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
Test Compatible Components
153
Microsoft® Windows® Vista Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Online Support Information
161
Index
163
IX
Table of Contents
X
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many features:
Operating System
•
Genuine Windows® Vista™
Platform
•
Intel® Pentium® dual-core processor*
•
Intel® Celeron® processor*
•
Mobile Intel® GL40 Express Chipset
•
IEEE 802.11b/g
System Memory
•
Dual-channel support
•
Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules
Display and graphics
•
14.1" WXGA 1280 x 800
•
Mobile Intel® GL40 Express Chipset
Storage subsystem
•
2.5" hard disk drive
•
Optical drive option:
•
DVD-Super Multi double-layer drive*
•
DVD/CD-RW combo drive*
Audio
•
Two built-in stereo speakers
•
High-definition audio support
•
MS-Sound compatible
•
Built-in microphone
Dimensions and Weight
Chapter 1
•
340.4 (W) x 247 (D) x 22.9/42.3 (H) mm (13.4 x 9.7 x 0.9/1.6 inches)
•
2.40 kg (5.29 lbs.) with 6-cell battery pack
1
Communication
•
Integrated webcam*
•
WLAN: IEEE 802.11b/g
•
LAN: Fast Ethernet; Wake-on-LAN ready
Privacy control
•
BIOS user, supervisor, HDD passwords
•
Kensington lock slot
Power subsystem
•
ACPI 3.0
•
48.8 W 4400 mAh
•
3-pin 65 W AC adapter
•
ENERGY STAR® 4.0*
Special keys and controls
•
88-/89-key keyboard
•
Touchpad pointing device
I/O interface
•
USB 2.0 port
•
External display (VGA) port
•
Headphones/speaker/line-out jack
•
Microphone-in jack
•
Line-in jack
•
Ethernet (RJ-45) port
•
DC-in jack for AC adapter
Environment
•
•
Temperature:
•
Operating: 5 °C to 35 °C
•
Non-operating: -20 °C to 65 °C
Humidity (non-condensing):
•
Operating: 20% to 80%
•
Non-operating: 20% to 80%
NOTE: Items marked with * denote only selected models.
2
Chapter 1
System Block Diagram
Chapter 1
3
Your Acer Notebook tour
After knowing your computer features, let us show you around your new computer.
Front View
No.
4
Icon
Item
Description
1
Microphone
Internal microphone for sound recording.
2
Integrated
webcam
Web camera for video communication
(for selected models).
3
Display screen
Also called Liquid-Crystal Display (LCD),
displays computer output.
4
Power button
Turns the computer on and off.
5
Wireless LAN
communication
button/indicator
Enables/disables the wireless LAN function.
Indicates the status of wireless LAN
communication.
6
Speakers
Left and right speakers deliver stereo audio
output.
7
Keyboard
For entering data into your computer.
8
Palmrest
Comfortable support area for your hands when
you use the computer.
Chapter 1
No.
Icon
Item
Description
9
TouchPad
Touch-sensitive pointing device which functions
like a computer mouse.
10
Click buttons (left
and right)
The left and right buttons function like the left
and right mouse buttons.
11
Power
Indicates the computer's power status.
Battery
Indicates the computer's battery status.
1. Charging: The light shows amber when the
battery is charging.
2. Fully charged: The light shows green when
in AC mode.
HDD
Indicates when the hard disk drive is active.
Num Lock
Lights up when Num Lock is activated.
Caps Lock
Lights up when Caps Lock is activated.
NOTE: The Power and Battery indicators are visible even when the computer cover is closed
Closed Front View
No.
Icon
1
Item
Latch
Description
Locks and releases the lid
Rear View
No.
1
Chapter 1
Icon
Item
Ventilation slots
Description
Enable the computer to stay cool, even after
prolonged use.
5
Left View
No.
6
Icon
Item
Description
1
Ethernet (RJ-45)
port
Connects to an Ethernet 10/100-based
network.
2
External display
(VGA) port
Connects to a display device
(e.g. external monitor, LCD projector).
3
USB 2.0 ports
Connect to USB 2.0 devices (e.g. USB mouse,
USB camera).
Line-in jack
Accepts audio line-in devices (e.g., audio CD
player, stereo walkman, mp3 player).
Microphone-in
jack
Accepts input from external microphones.
Headphones/
speaker/line-out
jack
Connects to audio line-out devices
(e.g. speakers, headphones).
Chapter 1
Right View
No.
Icon
Item
Description
1
Kensington lock
slot
Connects to a Kensington-compatible computer
security lock.
Note: Wrap the computer security lock cable
around an immovable object such as a table or
handle of a locked drawer. Insert the lock into the
notch and turn the key to secure the lock.
Some keyless models are also available.
2
Optical drive
Internal optical drive; accepts CDs or DVDs.
3
Optical disk access
indicator
Lights up when the optical drive is active.
4
Optical drive eject
button
Ejects the optical disk from the drive.
5
Emergency eject
hole
Ejects the optical drive tray when the computer is
turned off.
Note: Insert a paper clip into the emergency eject
hole to eject the optical drive tray when the
computer is off.
8
DC-in jack
Connects to an AC adapter
Chapter 1
7
Bottom View
No.
8
Icon
Item
Description
1
Battery bay
Houses the computer's battery pack.
2
Battery release
latch
Releases the battery for removal.
3
Memory
compartment
Houses the computer's main memory.
4
Hard disk bay
Houses the computer's hard disk (secured with
screws).
5
Battery lock
Locks the battery in position.
6
Ventilation slots
and cooling fan
Enable the computer to stay cool, even after
prolonged use.
Note: Do not cover or obstruct the opening of the
fan.
Chapter 1
Indicators
The computer has several easy-to-read status indicators. The front panel indicators are visible even when the
computer cover is closed.
Icon
Function
Description
Power
Indicates the computer's power status.
Battery
Indicates the computer's battery status.
HDD
Indicates when the hard disk drive is active.
Num Lock
Lights up when Num Lock is activated.
Caps Lock
Lights up when Caps Lock is activated.
NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows
green when in AC mode.
Chapter 1
9
TouchPad Basics (with fingerprint reader)
The following items show you how to use the TouchPad with Acer Bio-Protection fingerprint reader:
•
Move your finger across the TouchPad (1) to move the cursor.
•
Press the left (2) and right (3) buttons located beneath the TouchPad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the TouchPad is the same as clicking the left button.
Function
Left Button (2)
Right Button (3)
Main TouchPad (2)
Execute
Quickly click twice.
Tap twice (at the same speed
as double-clicking a mouse
button).
Select
Click once.
Tap once.
Drag
Click and hold, then use
finger on the TouchPad to
drag the cursor.
Tap twice (at the same speed
as double-clicking a mouse
button); rest your finger on
the TouchPad on the second
tap and drag the cursor.
Access
context menu
Click once.
NOTE: When using the TouchPad, keep it - and your fingers - dry and clean. The TouchPad is sensitive to
finger movement; hence, the lighter the touch, the better the response. Tapping too hard will not
increase the TouchPad’s responsiveness.
10
Chapter 1
Using the Keyboard
The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function
and special keys.
Lock Keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.
Lock key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters typed are in uppercase.
Num Lock
<Fn> + <F11>
When Num Lock is on, the embedded keypad is in numeric mode. The keys
function as a calculator (complete with the arithmetic operators +, -, *, and /). Use
this mode when you need to do a lot of numeric data entry. A better solution
would be to connect an external keypad.
Scroll Lock <Fn> +
<F12>
When Scroll Lock is on, the screen moves one line up or down when you press
the up or down arrow keys respectively. Scroll Lock does not work with some
applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access
Num Lock on
Num Lock off
Number keys on
embedded keypad
Type numbers in a normal manner.
Cursor-control keys on
embedded keypad
Hold <Shift> while using cursorcontrol keys.
Hold <Fn> while using cursorcontrol keys.
Main keyboard keys
Hold <Fn> while typing letters on
embedded keypad.
Type the letters in a normal
manner.
Chapter 1
11
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key
Description
Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button;
it launches the Start menu. It can also be used with other keys to provide a variety of
functions:
<
>:
Open or close the Start menu
<
>
+ <D>: Display the desktop
<
>
+ <E>: Open Windows Explore
<
>
+ <F>: Search for a file or folder
<
>
+ <G>: Cycle through Sidebar gadgets
<
>
+ <L>: Lock your computer (if you are connected to a network domain), or
switch users (if you're not connected to a network domain)
<
>
+ <M>: Minimizes all windows
<
>
+ <R>: Open the Run dialog box
<
>
+ <T>: Cycle through programs on the taskbar
<
>
+ <U>: Open Ease of Access Center
<
>
+ <X>: Open Windows Mobility Center
<
>
+ <BREAK>: Display the System Properties dialog box
<
>
+ <SHIFT+M>: Restore minimized windows to the desktop
<
>
+ <TAB>: Cycle through programs on the taskbar by using Windows Flip 3-D
<
>
+ <SPACEBAR>: Bring all gadgets to the front and select Windows Sidebar
<CTRL> + <
>
<CTRL> + <
>
+ <F>: Search for computers (if you are on a network)
+ <TAB>: Use the arrow keys to cycle through programs on the
taskbar by using Windows Flip 3-D
Note: Depending on your edition of Windows Vista, some shortcuts may not function
as described.
Application
key
12
This key has the same effect as clicking the right mouse button; it opens the
application's context menu.
Chapter 1
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like screen
brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Hotkey
Icon
Function
Description
<Fn> + <F1>
Hotkey help
Displays help on hotkeys.
<Fn> + <F2>
Acer eSettings
Management
Launches Acer eSettings Management in Acer
Empowering Technology.
<Fn> + <F3>
Acer ePower
Management
Launches Acer ePower Management in Acer
Empowering Technology.
<Fn> + <F4>
Sleep
Puts the computer in Sleep mode.
<Fn> + <F5>
Display toggle
Switches display output between the display
screen, external monitor (if connected) and
both.
<Fn> + <F6>
Screen blank
Turns the display screen backlight off to save
power. Press any key to return.
<Fn> + <F7>
TouchPad toggle
Turns the internal TouchPad on and off.
<Fn> + <F8>
Speaker toggle
Turns the speakers on and off.
<Fn> + < >
Brightness up
Increases the screen brightness.
<Fn> + < >
Brightness down
Decreases the screen brightness.
Chapter 1
13
Special Key
You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your
keyboard.
The Euro symbol
1.
Open a text editor or word processor.
2. Hold <Alt Gr> and then press the <5> key at the upper-center of the keyboard.
NOTE: Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
The US dollar sign
1.
Open a text editor or word processor.
2. Hold <Shift> and then press the <4> key at the upper-center of the keyboard.
NOTE: This function varies by the operating system version.
14
Chapter 1
Using the System Utilities
Acer GridVista (dual-display compatible)
NOTE: This feature is only available on certain models.
To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then
select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the
display box and then click the check box Extend my windows desktop onto this monitor. Finally, click
Apply to confirm the new settings and click OK to complete the process.
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows
on the same screen. To access this function, please go to Start´ All Programs and click on Acer GridVista.
You may choose any one of the four display settings indicated below:
Double (vertical), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display
compatible, allowing two displays to be partitioned independently.
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.
AcerGridVista is simple to set up:
1.
2.
3.
Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
Drag and drop each window into the appropriate grid.
Enjoy the convenience of a well-organized desktop.
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.
Chapter 1
15
Hardware Specifications and Configurations
Processor
Item
Specification
CPU type
Penryn based Intel® Celeron Processor and Intel® Pentium
Processor
Core logic
Intel Cantiga GL40 (667MHz FSB supported)
ICH9-M
ENE KB926 for Keyboard Controller, Battery management Unit.
Integrated VGA solution for CANTIGA GL40
REALTEK ALC268 for High Definition Audio Codec.
REALTEK RTL8111C-GR for Giga LAN
CPU package
Micro uPGA-478
CPU Fan True Value Table
CPU Temperature
Core 0
Fan Speed (rpm)
Core 1
SPL Spec (dBA)
50
50
3000
31
60
60
3400
34
70
70
3700
37
77
77
4000
40
85
85
4000
40
•
Throttling 50%: On= 85°C; OFF=78°C
•
OS shut down at 90°C; H/W shut down at 96°C
BIOS
Item
Specification
BIOS vendor
Insyde
BIOS Version
V0.15T2
BIOS ROM type
Flash
BIOS ROM size
1 MB
Supported protocols
•
•
•
•
•
•
•
•
•
•
•
•
BIOS password control
16
Flash ROM 1MB
Support multi-boot
Suspend to RAM (S3)/Disk (S4)
Various hot-keys for system control
Support SMBUS 2.0, PCI2.3
ACPI 2.0 compliance with Intel Speed Step Support C1, C2, C3
and S3, S4 for mobile CPU
DMI utility for BIOS serial number configurable/asset tag
Support PXE
Support Y2K solution
Support Win Flash Wake on LAN from S3
Wake on LAN form S4 in AC mode
System information
BIOS user, Supervisor and HDD passwords
Chapter 1
System Memory
Item
Specification
Memory controller
Built-in
Memory size
0MB (no on-board memory)
DIMM socket number
2 sockets
Supports memory size per socket
2 GB
Supports maximum memory size
4G for 64bit OS (with two 2GB SODIMM)
Supports DIMM type
DDR 2 Synchronous DRAM
Supports DIMM Speed
667 MHz
Supports DIMM voltage
1.8V
Supports DIMM package
200-pin soDIMM
Memory Combinations
Slot 1
Slot 2
Total Memory
0MB
512MB
512MB
0MB
1024MB
1024MB
0MB
2048MB
2048MB
512MB
512MB
1024MB
512MB
1024MB
1536MB
512MB
2048MB
2560MB
1024MB
0MB
1024MB
1024MB
512MB
1536MB
1024MB
1024MB
2048MB
1024MB
2048MB
3072MB
2048MB
0MB
2048MB
2048MB
512MB
2560MB
2048MB
1024MB
3072MB
2048MB
2048MB
4096MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be
reversed.
LAN Interface
Item
Specification
LAN Chipset
REALTEK RTL8111C-GR for GIGA LAN
Supports LAN protocol
PCI-E 10/100/1000 MB LAN
LAN connector type
RJ-45
LAN connector location
Left side
Features
Support Wake-On-Lan (AC mode S5)
Wireless Module 802.11b/g
Item
Specification
Chipset
Data throughput
Protocol
Interface
Chapter 1
17
Hard Disk Drive Interface
Item
Specification
Vendor
Seagate Momentus 5400.4 SATA
Model Name
ST9250827AS
ST9160827AS
ST9120817AS
Capacity (MB)
250
160
120
Bytes per sector
512
Data heads
4
3
2
2
2
1
Drive Format
Disks
Spindle speed (RPM)
5,400
Performance Specifications
Buffer size
8MB
Interface
SATA
Internal transfer rate (Mbits/
sec max)
778
Sustained transfer rate
(Mbytes/sec max)
58
I/O data transfer rate
(Mbytes/sec max)
300
DC Power Requirements
Voltage tolerance
5V(DC) +/- 5%
Item
Specification
Vendor
Seagate Momentus 5400.5 SATA
Model Name
ST9320320AS
ST9250320AS
ST9160310AS
ST9120310AS
Capacity (MB)
320
250
160
120
4
4 or 3
2
2
2 or 1
2
1
1
Bytes per sector
Data heads
512
Drive Format
Disks
Spindle speed (RPM)
5,400
Performance Specifications
Buffer size
8 MB
Interface
SATA
Internal transfer rate
(Mbits/sec max)
352
I/O data transfer rate
(Mbytes/sec max)
150
DC Power Requirements
Voltage tolerance
18
5V(DC) +/- 5%
Chapter 1
Super-Multi Drive Module
Item
Specification
Vendor & model name
HLDS/GSA-T50N, Philips DS-8A2S, Sony/AD-7560S, Toshiba Digi/TS-L633A
Performance Specification
With CD Diskette
With DVD Diskette
Transfer rate (MB/sec)
Sustained:
Max 3.5 Mbytes/sec
Sustained:
Max 10 Mbytes/sec
Buffer Memory
2MB
Interface
SATA
Applicable disc format
Applicable media types:
Writing:
Confirms to DVD+R Version 1.2 and DVD+RW Version 1.3 / DVD+R DL
Version 1.0 /DVD-R Version 2.0 / DVD-RW Version 1.2 / DVD-R DL Version
3.0.
Reading:
DVD single/dual layer (PTP, OTP), DVD-R single/dual layer
DVD+R single/double layer
DVD-RW
DVD+RW
CD-DA
CD-ROM
CD-ROM/XA
Photo-CD, Multi-session, Video CD
CD-I FMV, CD Extra, CD Plus, CD-R, and CD-RW
Loading mechanism
Drawer (Solenoid Open)
Tact SW (Open)
Emergency Release (draw open hole)
Power Requirement
Input Voltage
DC 5 V +/- 5%
Audio Interface
Item
Specification
Audio Controller
REALTEK ALC268 for High Definition Audio Codec
Mono or Stereo
Stereo
Compatibility
MIC IN—AC-coupled input,100mVP-P maximum
LINE IN—AC-coupled input,100mVP-P maximum
Headphone out—1VP-P
Build-in Speaker—4 ohm, 2W Main Speaker
System Board Major Chips
Item
Controller
Core logic
Intel® Core™2 Duo processor based Intel® Celeron
processor and Intel® Pentium processor, FSB 667MHz
LAN
REALTEK RTL8111C-GR for GIGA LAN
Audio Codec
REALTEK ALC268 for High Definition Audio Codec
Keyboard
Item
Specification
Keyboard controller
KB926
Total number of keypads
88-/89-key keyboard
Chapter 1
19
Item
Specification
Windows logo key
Yes
Internal & external keyboard work
simultaneously
Yes
Battery
Item
Specification
Vendor & model name
Sanyo, Sony, Panasonic, Simplo
Battery Type
Li Ion
Pack capacity
2400/4400 mAh
Number of battery cell
6
Package configuration
3S2P
LCD 14.1”
Item
Specification
Vendor/model name
LG.Philips/LP141WX3, AUO/B141EW04 V4,
Chimei/N141I3 - L02, Samsung/LTN141W3-L01
Screen Diagonal (mm)
14.1 inches
Active Area (mm)
303.74 x 189.84 mm
Display resolution (pixels)
1280 x 800 WXGA
Pixel Pitch
0.2373 × 0.2373 mm
Pixel Arrangement
R.G.B. Vertical Stripe
Display Mode
Typical White Luminance (cd/m
also called Brightness
20
Transmissive mode, normally white
2)
200 cd/m2(Typ.5 point)
Luminance Uniformity
1.3 max.
Contrast Ratio
300 minimum
Response Time (Optical Rise
Time/Fall Time) msec
16
Nominal Input Voltage VDD
+3.3V
Typical Power Consumption (watt)
1.4W max.
Weight (without inverter)
400g max.
Physical Size (mm)
319.5 (±0.5) x 205.5 (± 0.5) x 5.5 max.
Electrical Interface
3.3V LVDS interface with 1 pixel/clock
Support Color
greater than 262144
Viewing Angle (degree)
Horizontal: Right/Left
Vertical: Upper/Lower
Minimum: 40/40, Typical: 45/45
Minimum: 10/30, Typical: 20/35
Temperature Range (°C)
Operating
Storage (shipping)
0 to +50
-20 to +60
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Navigating the BIOS Utility
There are six menu options: Information, Main, Advanced, Security, Boot, and Exit.
Follow these instructions:
•
To choose a menu, use the left and right arrow keys.
•
To choose an item, use the up and down arrow keys.
•
To change the value of a parameter, press F5 or F6.
•
A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
•
Press Esc while you are in any of the menu options to go to the Exit menu.
In any menu, you can load default settings by pressing F9. You can also press F10 to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information is subject to different models.
•
Chapter 2
21
Information
The Information screen displays a summary of your computer hardware information.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
Rev. 3.5
Boot
Exit
CPU Type:
CPU Speed:
Intel (R) Core (TM)2 Duo CPU @ 2.40GHz
2.40GHz
HDD Model Name:
HDD Serial Number:
ATAPI Model Name:
Hitachi HTS543516K9SA00
071129BB0C02WGHDKKGC
Slimtype DVD A DS8A2S
System BIOS Version:
VGA BIOS Version:
Serial Number:
Asset Tag Number:
Product Name:
Manufacturer Name:
UUID:
V0.15T2
Intel V1588
F1 Help
ESC Exit
Aspire 4930
Acer
864BD4BE-6B22-5843-38D2-001B38D637FC
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
NOTE: The system information is subject to different models.
Parameter
22
Description
CPU Type
This field shows the CPU type and speed of the system.
CPU Speed
This field shows the speed of the CPU.
HDD Model Name
This field shows the model name of HDD installed on primary IDE master.
HDD Serial Number
This field displays the serial number of HDD installed on primary IDE master.
ATAPI Model Name
This field shows the model name of the Optical device installed in the system.
System BIOS Version
Displays system BIOS version.
VGA BIOS Version
This field displays the VGA firmware version of the system.
Serial Number
This field displays the serial number of this unit.
Asset Tag Number
This field displays the asset tag number of the system.
Product Name
This field shows product name of the system.
Manufacturer Name
This field displays the manufacturer of this system.
UUID Number
Universally Unique Identifier (UUID) is an identifier standard used in software
construction, standardized by the Open Software Foundation (OSF) as part of
the Distributed Computing Environment (DCE).
Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option
and recovery.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
System Time
System Date
[13:04:04]
[04/21/2008]
Total Memory
Video Memory
3017 MB
[32MB]
Quick Boot
Network Boot
F12 Boot Menu
D2D Recovery
SATA Mode
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[ACHI]
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
Boot
Rev. 3.5
Exit
Item Specific Help
This is the help for the
hour field. Valid range
is from 0 to 23.
INCREASE/REDUCE : F5/F6
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
NOTE: The screen above is for your reference only. Actual values may differ.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time. The hours are displayed with 24hour format.
Format: HH:MM:SS
(hour:minute:second)
System Date
Sets the system date.
Format MM/DD/YYYY
(month/day/year)
Total Memory
This field reports the memory size of the system.
Memory size is fixed to 3017 MB.
N/A
Video Memory
Shows the video memory size. VGA Memory size=32 MB
N/A
Quick Boot
Allows startup to skip certain tests while booting,
decreasing the time needed to boot the system.
Option: Enabled or
Disabled
Network Boot
Enables, disables the system boot from LAN (remote
server).
Option: Enabled or
Disabled
F12 Boot Menu
Enables, disables Boot Menu during POST.
Option: Disabled or
Enabled
D2D Recovery
Enables, disables D2D Recovery function. The function
allows the user to create a hidden partition on hard disc
drive to store operation system and restore the system
to factory defaults.
Option: Enabled or
Disabled
SATA Mode
Control the mode in which the SATA controller should
operate.
Option: AHCI Mode or IDE
Mode
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Chapter 2
23
Advanced
The Advanced screen allows the user to configure the various advanced BIOS options.
IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless
you have experience adjusting these items, we recommend that you leave these settings at the
default values. If making settings to items on these pages causes your system to malfunction or
prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to
boot up normally.
Information
InsydeH20 Setup Utility
Advanced
Security
Power
Main
XBoot Configuration
XPeripheral Configuration
XIDE Configuration
XVideo Configuration
XUSB Configuration
XChipset Configuration
XACPI Table/Features Control
Express Card
XPCI Express Root Port 1
XPCI Express Root Port 2
XPCI Express Root Port 3
XPCI Express Root Port 4
XPCI Express Root Port 5
XPCI Express Root Port 6
Rev. 3.5
Boot
Exit
Item Specific Help
Configures Boot
Settings.
[Disabled]
XASF Configuration
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default
and suggested parameter settings.
Parameter
24
Description
Submenu Items
Boot
Configuration
Enter the Boot Configuration menu.
•
•
Numlock
Zip Emulation Type
Peripheral
Configuration
Enter the Peripheral Configuration menu.
•
•
•
•
Serial Port A
Infrared Port
Azalia
LAN
IDE
Configuration
Enter the IDE Configuration menu.
•
•
•
•
•
IDE Controller
HDC Configure as
ACHI Option ROM Support
SATA Port 0, 1, 4, and 5 Hotplug
Channel 1 to 4 Master and Slave
Video
Configuration
Enter the Video Configuration menu.
•
•
•
•
•
•
•
•
IGD Device2, Function1
IGD Pre-allocate Memory
IGD DVMT Size
Clock Chip Intialize
Enabled CK SSC
IGD Boot Type
IGD LCD Panel Type
IGD TV
Chapter 2
Parameter
Description
Submenu Items
USB
Configuration
Enter the USB Configuration menu.
•
•
•
•
USB Driver Select
EHCI 1 and 2
UHCI 1 to 5
Per-Port Control
Chipset
Configuration
Enter the Chipset Configuration menu.
•
•
•
•
Port 80h Cycles
DMI Link ASPM Control
PCI Latency Timer
VT-d
ACPI Table/
Features Control
Enter the ACPI Table/Features Control
menu.
•
•
•
•
•
•
FACP C2 Latency Value
FACP C3 Latency Value
FACP RTC S4 Wakeup
APIC IO APIC Mode
HPET Support
Base Address Select
Express Card
Disable or Enable the Express Card
solution for windows Standby and
Hibernation.
N/A
PCI Express
Root Port 1 to 6
Enter the PCI Port 1 to 6 configuration
menus.
•
•
•
•
•
•
•
•
•
•
•
•
•
VC1 Enable
ASPM
URR
FER
NFER
CER
CTO
SEFE
SENFE
SECE
PME Interrupt
PME SCI
Hot Plug SCI
ASF
Configuration
Enter the ASF Configuration menu.
•
•
•
•
Mini Watchdog Timeout
BIOS Boot Timeout
OS Boot Timeout
Power-on wait time
Chapter 2
25
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
Supervisor Password Is:
User Password Is:
HDD Password Is:
Clear
Clear
Clear
Set Supervisor Password
Set User Password
Set Hdd Password
Power on password
[32MB]
F1 Help
ESC Exit
Boot
Rev. 3.5
Exit
Item Specific Help
Install or Change the
password and the length
of password must be less
than eight words.
[Enabled]
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
Supervisor Password Is
Shows the setting of the Supervisor password
Clear or Set
User Password Is
Shows the setting of the user password.
Clear or Set
HDD Password Is
Shows the setting of the hard disk password.
Clear or Set
Set Supervisor Password
Press Enter to set the supervisor password. When
set, this password protects the BIOS Setup Utility
from unauthorized access. The user can not either
enter the Setup menu nor change the value of
parameters.
Set User Password
Press Enter to set the user password. When user
password is set, this password protects the BIOS
Setup Utility from unauthorized access. The user can
enter Setup menu only and does not have right to
change the value of parameters.
Set HDD Password
Enter HDD Password.
Password on Boot
Defines whether a password is required or not while
the events defined in this group happened. The
following sub-options are all requires the Supervisor
password for changes and should be grayed out if the
user password was used to enter setup.
Disabled or
Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
26
Chapter 2
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Supervisor Password box appears:
2.
Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.
Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
4.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press Enter.
3.
Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2
27
Changing a Password
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Password box appears.
2.
Type the current password in the Enter Current Password field and press Enter.
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses Enter.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
28
Chapter 2
Power
The Power screen allows the user to configure various CPU and power management options and device
wakeup behavior.
Information
InsydeH20 Setup Utility
Advanced
Security
Power
Main
Boot
XAdvanced CPU Control
XPlatform Power Management
ACPI S3:
Wake on PME
Wake on Modem Ring
Auto wake on S5
Quickly S4 Resume
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
Rev. 3.5
Exit
Item Specific Help
These items control
various CPU parameters.
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[Disabled]
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default
and suggested parameter settings.
Parameter
Advanced CPU
Control
Chapter 2
Description
Enter the Advanced CPU Control menu.
Submenu Items
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
P-States (IST)
Boot performance mode
Thermal Mode
CMP Support
Use XD capability
VT Support
C-States
Enhanced C-States
C-State Pop Up Mode
C-State Pop Down Mode
C4 Exit Timing Mode
DeepC4
Hard C4E
Enable C6
EMTTM
Bi-directional PROCHOT#
Dynamic FSB Switching
Turbo Mode
ACPI 3.0 T-States
DTS
DTS Calibration
Thermal Trip Points Setting (Fan
On Temp., Throttle On Temp.)
29
Parameter
30
Description
Submenu Items
Platform Power
management
Enter the Platform Power Management
menu.
•
•
•
PCI Clock Run
_CST - C4 Latency Value
C4 on C3 - Deeper Sleep
ACPI S3
Enable or Disable ACPI S1/S3 Sleep State
N/A
Wake on PME
Enable or Disable wake up when the
system power is off and a PCI Power
Management Enable wake up event occurs.
N/A
Wake on Modem
Ring
Enable or Disable wake up when the
system power is off and a modem attached
to the serial port is ringing.
N/A
Auto wake on S5
Disable or Enable auto wake up by date
and time or at a fixed time everyday.
N/A
Quickly S4
Resume
Disable or Enable optional quick boot from
S4 Resume.
N/A
Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
Boot priority order:
1. IDE0 : Hitachi HTS542516K9SA00
2. IDE1 : Slimtype DVD A DS8A2S
3 . USB FDD :
4. Network Boot : Realtek Boot Agent
5. USB HDD :
6. USB CDROM :
F1 Help
ESC Exit
Chapter 2
↑↓ Select Item
←→ Select Menu
Boot
Rev. 3.5
Exit
Item Specific Help
Use <↑> or <↓> to select
a device, then press
<F5> to move it down the
list, or <F6> to move
it up the list. Press
<Esc> to escape the menu
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
31
Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
Boot
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
Rev. 3.5
Exit
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
32
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS.
Exit Discarding
Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
BIOS Flash Utilities
The BIOS flash memory update is required for the following conditions:
•
New versions of system programs
•
New features or options
•
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
1.
Prepare a bootable diskette.
2.
Copy the flash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The flash utility has auto-execution function.
Chapter 2
33
DOS Flash Utility
Perform the following steps to use the DOS Flash Utility:
1.
Press F2 during boot to enter the Setup Menu.
2.
Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move
USB HDD to position 1.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power Boot
Boot priority order:
1. IDE0 : Hitachi HTS542516K9SA00
2. IDE1 : Slimtype DVD A DS8A2S
3 . USB FDD :
4. Network Boot : Realtek Boot Agent
5. USB HDD : ABC
6. USB CDROM :
F1 Help
ESC Exit
3.
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
Enter Select XSubmenu
Rev. 3.5
Exit
Item Specific Help
Use < ↑ > or < ↓ > to select
a device, then press
<F5> to move it down the
list, or <F6> to move
it up the list. Press
<Esc> to escape the menu
F9 Setup Default
F10 Save and Exit
Execute the IFLASH.BAT batch file to update BIOS.
The flash process begins as shown.
34
Chapter 2
4. In flash BIOS, the message Please do not remove AC Power Source displays.
NOTE: If the AC power is not connected, the following message displays.
Plug in the AC power to continue.
5.
Flash is complete when the message Flash programming complete displays.
Chapter 2
35
WinFlash Utility
Perform the following steps to use the WinFlash Utility:
36
1.
Double click the WinFlash executable.
2.
Click OK to begin the update. A progress screen displays.
3.
When the process is complete, close all programs and applications and reboot the system.
Chapter 2
Remove HDD/BIOS Password Utilities
This section provide you with removing HDD/BIOS method:
Remove HDD Password:
When the user keys in the wrong password three times, the system reports the following error code to user.
To unlock the HDD password, perform the following steps:
1.
Press Enter to display the Select Item screen.
2.
Select Enter Unlock Password and press Enter.
An Unlock Password displays.
3.
Make a note of the key, 76943488 in the example.
4.
Boot up the system and open a DOS prompt.
5.
Enter the UnlockHD.EXE command and input the key to create an unlock code. Make a note of the
result, for example 46548274.
6.
Reboot and enter the BIOS by pressing F2 when prompted.
7.
Go to the Security menu and select Set Hdd Password (see “Security” on page 26).
8.
Enter the unlock code generated by UnlockHD.EXE as the current password, 46548274 in the example,
and complete the New Password and Confirm fields to create a new HDD password.
9.
Save and exit the BIOS to complete the process.
Chapter 2
37
Removing BIOS Passwords:
If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the
image below.
To reset the BIOS password, run BIOS_PW.EXE as follows:
1. Key in bios_pw 14452 0
2. Select one string from the list.
38
Chapter 2
3. Reboot the system and key in the selected string (qjjg9vy, 07yqmjd etc.) for the BIOS user
password.
Cleaning BIOS Passwords
To clear the password, perform the following steps:
1.
From a DOS prompt, Execute clnpwd.exe
2.
Press 1 or 2 to clean the desired password shown on the screen.
The onscreen message determines whether the function is successful or not.
Chapter 2
39
40
Chapter 2
Chapter 3
Machine Disassembly and Replacement
IMPORTANT:The outside housing and color may vary from the mass produced model.
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
•
Wrist grounding strap and conductive mat for preventing electrostatic discharge
•
Flat screwdriver
•
Philips screwdriver
•
Plastic flat screwdriver
•
Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
IMPORTANT:Various images depict the use of a regular metal screwdriver, however, a plastic screwdriver is
advised when disassembling parts near or around the motherboard and to prevent scratching of the
computer surface.
Chapter 3
41
General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
3. Place the system on a flat, stable surface.
4. Remove the battery pack.
Disassembly Process
The disassembly process is divided into the following stages:
•
•
•
External module disassembly
Main unit disassembly
LCD module disassembly
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you
want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly
frame in that order.
Main Screw List
Screw
42
Quantity
Part Number
M2.5*8
15
86.AT902.001
M2.5*5
21
86.AT902.002
M2*L3
22
86.AT902.003
M2.5*4
3
86.AT902.004
M3*3
4
86.AT902.006
M2.5*6.5
4
86.AT902.007
Chapter 3
External Module Disassembly Process
IMPORTANT:The outside housing and color may vary from the mass produced model.
External Modules Disassembly Flowchart
The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you
on the components that need to be removed during servicing. For example, if you want to remove the main
board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Turn off system
and peripherals
power
Disconnect power
and signal cables
from system
Remove
Battery
Remove
Lower Covers
Remove
DIMMs
Remove
WLAN
Remove
HDD
Remove
ODD
Remove
Antenna
Screw List
Step
Screw
Quantity
Part No.
Memory Cover
M2.5*8
2
86.AT902.001
WLAN Cover
M2.5*8
1
86.AT902.001
WLAN Module
M2*L3
2
86.AT902.003
HDD Carrier
M3*3
4
86.AT902.006
ODD Module
M2.5*5
1
86.AT902.002
ODD Bracket
M2*L3
3
86.AT902.003
Chapter 3
43
Removing the Battery Pack
1. Turn computer over.
2. Slide the battery lock/unlock latch to the unlock position.
3. Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main
unit (2).
2
1
44
Chapter 3
Removing the Lower Covers
1. See “Removing the Battery Pack” on page 44.
2. Remove the three screws from the memory and WLAN bays and loosen the two captive screws on the HDD
cover.
Memory
Cover
HDD
Cover
WLAN
Cover
Step
Size
Quantity
Memory Cover
M2.5*8
2
WLAN Cover
M2.5*8
1
Screw Type
3. Carefully open the memory cover.
4. Remove the HDD cover as shown.
Chapter 3
45
5. Remove the WLAN cover as shown.
46
Chapter 3
Removing the DIMM Modules
1. See “Removing the Battery Pack” on page 44.
2. Remove the Memory Module cover See “Removing the Lower Covers” on page 45.
3. Push out the release latches on both sides of the DIMM socket to release the DIMM module.
4. Remove the DIMM module.
5. Repeat steps for the second DIMM module if present.
Chapter 3
47
Removing the WLAN Module
1. See “Removing the Battery Pack” on page 44.
2. Remove the WLAN cover. See “Removing the Lower Covers” on page 45.
3. Disconnect the antenna cables from the WLAN board.
4. Move the antenna away and remove the two screws on the WLAN board to release the WLAN board.
Step
WLAN Module
Size
M2*L3
Quantity
Screw Type
2
5. Detach the WLAN board from the WLAN socket.
48
Chapter 3
NOTE: When attaching the antenna back to the WLAN board, make sure the cables are sitting in the housing
to prevent damage.
Chapter 3
49
Removing the Hard Disk Drive Module
1. See “Removing the Battery Pack” on page 44.
2. Remove the HDD cover, See “Removing the Lower Covers” on page 45.
3. Use the pull-tab to pull and lift the hard disk drive module out of the bay.
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
4. Remove the four screws securing the hard disk to the carrier.
50
Chapter 3
Step
HDD Carrier
Size
M3*3
Quantity
Screw Type
4
5. Remove the HDD from the carrier.
Chapter 3
51
Removing the Optical Drive Module
1. See “Removing the Battery Pack” on page 44.
2. Remove the Memory cover. See “Removing the Lower Covers” on page 45.
3. Remove the screw securing the ODD module.
Step
ODD Module
Size
M2.5*5
Quantity
Screw Type
1
4. Pull the optical drive module out from the chassis.
52
Chapter 3
5. Remove the three screws securing the ODD bracket and remove the ODD bracket from the optical disk drive
module.
Step
ODD Bracket
Size
M2*L3
Quantity
Screw Type
3
6. Insert a pin in the eject hole of the ODD to eject the ODD tray.
7. Press down on the locking catch to release the ODD cover and remove.
Chapter 3
53
Main Unit Disassembly Process
IMPORTANT:The outside housing and color may vary from the mass produced model.
Main Unit Disassembly Flowchart
Remove External
Modules before
proceeding
Remove
Switch Cover
Remove
Keyboard
Remove
Antenna
Remove
LCD Module
Remove
Upper Case
Remove
TouchPad
Bracket
Remove
Speaker Module
Remove
Lower Case
Remove
Power Board
Remove
Modem Module
Remove
Mainboard
Remove
CPU Fan
Remove
Thermal Module
Remove
CPU
Screw List
Step
Quantity
Part No.
Switch Cover
M2.5*5
3
86.AT902.002
LCD Module
M2.5*8
2
86.AT902.001
M2.5*8
2
86.AT902.001
M2.5*5
2
86.AT902.002
Upper Cover
54
Screw
M2.5*8
8
86.AT902.001
M2.5*5
7
86.AT902.002
TouchPad Bracket
M2*L3
2
86.AT902.003
Speaker Module
M2*L3
4
86.AT902.003
Modem Module
M2*L3
2
86.AT902.003
Mainboard
M2.5*5
1
86.AT902.002
CPU Fan
M2.5*4
3
86.AT902.004
Thermal Module
M2.5*6.5
4
86.AT902.007
Chapter 3
Removing the Switch Cover
CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is
recommended that you only use your fingers to remove the Switch Cover.
1. See “Removing the Battery Pack” on page 44.
2. Locate and remove the three securing screws from the battery bay.
Step
Switch Cover
Size
M2.5*5
Quantity
Screw Type
3
3. Turn the computer over and open the LCD module to expose the Switch Cover.
4. Lift the Switch Cover as shown, and move from right to left side.
5. Lift the Switch Cover clear of the chassis.
Chapter 3
55
56
Chapter 3
Removing the Keyboard
1. See “Removing the Switch Cover” on page 55.
2. Lift the keyboard away from the chassis as shown.
3. Turn the keyboard over on the TouchPad area to expose the FFC cable.
4. Open the cable retainer and disconnect the FFC cable from the mainboard.
5. Lift the keyboard clear of the chassis.
Chapter 3
57
Removing the Antenna
1. See See “Removing the Keyboard” on page 57.
2. Remove the Antenna Cables from the securing pins as shown.
3. Turn the computer over. Remove the adhesive strip holding the antenna cables.
4. Feed the antenna cables from the underside of the computer.
58
Chapter 3
5. Remove the Antenna Cables from the securing pins as shown.
Chapter 3
59
Removing the LCD Module
1. See “Removing the Battery Pack” on page 44.
2. See “Removing the Antenna” on page 58.
3. Remove the two securing screws from the bottom of the chassis.
Step
LCD Module
Size
M2.5*8
Quantity
Screw Type
2
4. Turn the computer over. Peel back the protective film to expose the interface cables.
5. Disconnect the two LCD interface cables from the chassis.
60
Chapter 3
6. Remove the four securing screws (two each side) from the LCD module.
Step
Size
Quantity
LCD Module
(red callout)
M2.5*8
2
LCD Module
(blue callout)
M2.5*5
2
Screw Type
7. Carefully remove the LCD module from the chassis.
Chapter 3
61
Removing the Upper Cover
1. See “Removing the Battery Pack” on page 44.
2. See “Removing the Lower Covers” on page 45.
3. See “Removing the LCD Module” on page 60.
4. Turn the computer over. Remove the eight screws on the bottom panel.
Step
Upper Cover
Size
M2.5*8
Quantity
Screw Type
8
5. Turn the computer over. Remove the seven screws on the top panel.
Step
Upper Cover
62
Size
M2.5*5
Quantity
Screw Type
7
Chapter 3
6. Disconnect the three cables from the mainboard as shown.
B
A
C
Remove the adhesive tape to expose cable A.
Disconnect A as shown.
Release the securing latches and disconnect B as
shown.
Release the securing latches and disconnect C as
shown.
NOTE: Avoid pulling on the cables directly to prevent damage to the connectors.
NOTE: Use the pull-tabs on the FFC cables whenever available to prevent damage to the FFC cables.
Chapter 3
63
7. Remove the upper cover by lifting upward from the chassis, rear edge first.
8. Turn the upper cover over. The upper cover appears as follows.
64
Chapter 3
Removing the TouchPad Bracket
1. See “Removing the Upper Cover” on page 62.
2. Lift the cable latch and disconnect the TouchPad cable from the TouchPad board.
3. Remove the two securing screws from the TouchPad bracket.
Step
TouchPad Bracket
Size
M2*L3
Quantity
Screw Type
2
4. Push the TouchPad bracket to the left to clear the securing clip.
Chapter 3
65
5. Lift the rear edge of the TouchPad bracket first to clear the securing clips and remove the it as shown.
IMPORTANT:The TouchPad board is integrated into the design of the Upper Cover. To replace the TouchPad
board, remove all components from the Upper Cover and install an entirely new Upper Cover.
IMPORTANT:The MOSFET pad is attached to the Upper Cover and is reusable. If the replacement Upper
Cover does not have a MOSFET pad (see highlighted area below), remove the MOSFET pad from
the replaced Upper Cover and stick it to the new Upper Cover.
66
Chapter 3
Removing the Speaker Modules
1. See “Removing the Upper Cover” on page 62.
2. Remove the adhesive tape (blue callouts) and four securing screws (red callouts) from the speaker modules.
Step
Speaker Modules
(red callout)
Size
M2*L3
Quantity
Screw Type
4
3. Peel back the Power Board FFC cable to expose the speaker cable.
4. Remove the speaker cable from the cable guides as shown.
Chapter 3
67
5. Remove the Speaker Modules from the upper cover.
68
Chapter 3
Removing the Power Board
1. See “Removing the Upper Cover” on page 62.
2. Remove the adhesive tape from the Power Board cable as shown.
3. Turn the Upper Cover over. Remove the adhesive tape from the Power Board as shown.
4. Lift the Power Board away from the cover and pull the FFC cable through as shown.
Chapter 3
69
Removing the Modem Module
1. See “Removing the Upper Cover” on page 62.
2. Remove the two screws securing the Modem module.
Step
Modem Module
Size
M2*L3
Quantity
Screw Type
2
3. Remove the Modem module from the Lower Cover.
4. Disconnect the Modem cable from the Modem module.
70
Chapter 3
Removing the Main Board
1. See “Removing the Upper Cover” on page 62.
2. Remove the securing screw from the Mainboard.
Step
Mainboard
Size
M2.5*5
Quantity
Screw Type
1
3. Remove the main board, rightside first, as shown.
IMPORTANT:The DC IN cable is still attached to the mainboard at this stage. Do not remove the mainboard
from the chassis completely.
4. Turn the Mainboard over to expose the DC IN connector.
Chapter 3
71
5. Disconnect the DC IN Cable from the mainboard.
6. Remove the mainboard from the chassis and place it on a clean, dust-free surface.
72
Chapter 3
Removing the CPU Fan
1. See “Removing the Main Board” on page 71.
2. Disconnect the fan cable from the mainboard.
3. Remove the three securing screws from the fan module.
Step
Mainboard
Size
M2.5*4
Quantity
Screw Type
3
4. Lift the fan clear of the mainboard.
Chapter 3
73
Removing the Thermal Module
1. See “Removing the CPU Fan” on page 73.
2. Remove the four securing screws (in reverse numerical order from screw 4 to screw 1) from the Thermal
Module.
3
1
Step
Thermal Module
Size
M2.5*6.5
Quantity
2
4
Screw Type
4
3. Using both hands, lift the Thermal Module clear of the Mainboard.
74
Chapter 3
Removing the CPU
1. See “Removing the Main Board” on page 71.
2. See “Removing the Thermal Module” on page 74.
3. Using a flat screwdriver, turn the CPU socket latch counter-clockwise 180° to release the CPU.
k
4. Lift the CPU clear of the Mainboard.
Chapter 3
75
LCD Module Disassembly Process
IMPORTANT:The outside housing and color may vary from the mass produced model.
LCD Module Disassembly Flowchart
Remove LCD
Panel from Main
Unit before
proceeding
Remove
LCD Bezel
Remove
Inverter Board
Remove
LCD FPC Cable
Remove
LCD Panel
Remove
LCD Brackets
Remove
Camera Module
Remove
Antennas
Remove
MIC Cable
Screw List
Step
LCD Bezel
76
Screw
M2.5*5
Quantity
4
Part No.
86.AT902.002
Inverter Board
M2.5*5
1
86.AT902.002
Camera Module
M2*L3
1
86.AT902.003
LCD Panel
M2.5*5
2
86.AT902.002
LCD Brackets
M2*L3
8
86.AT902.003
Chapter 3
Removing the LCD Bezel
1. See “Removing the LCD Module” on page 60.
2. Remove the two upper and two lower bezel screw caps and screws.
Step
LCD Bezel
3.
Size
M2.5*5
Quantity
Screw Type
4
Starting from the upper inside edge of the bezel, pry the bezel upwards and away from the panel. Move along
the sides until all sides of the bezel are removed.
NOTE: If necessary, use a plastic pry to lift up the outside edges of the bezel.
Chapter 3
77
Removing the Inverter Board
1. See “Removing the LCD Bezel” on page 77.
2. Remove the securing screw and adhesive tape from the Inverter board.
Step
Inverter Board
Size
M2.5*5
Quantity
Screw Type
1
3. Disconnect the left Inverter board cable as shown.
4.
Lift the Inverter board clear of the LCD Module and disconnect the right cable.
5. Remove the Inverter board from the LCD module.
78
Chapter 3
Removing the Camera Module
1. See “Removing the LCD Bezel” on page 77.
2. Disconnect the Camera Module cable as shown.
3. Remove the single securing screw from the Camera Module.
Step
Camera Module
Size
M2*L3
Quantity
Screw Type
1
4. Lift the Camera Module, left side first, clear of the LCD Module.
Chapter 3
79
Removing the LCD Panel
1. See “Removing the LCD Bezel” on page 77.
2. Remove the two securing screws from the LCD Module.
Step
LCD Panel
Size
M2.5*5
Quantity
Screw Type
2
3. Lift the LCD Panel clear of the LCD Module.
80
Chapter 3
Removing the LCD Brackets and FPC Cable
1. See “Removing the LCD Panel” on page 80.
2. Turn the LCD panel over to expose the rear. Lift the camera connector clear of the panel.
3. Lift the adhesive protector and disconnect the cable from the LCD Panel.
4. Grip the FPC cable and lift upward to detach the adhesive pads and remove the cable from the panel.
5. Remove the eight securing screws (four on each side) from the LCD Panel brackets.
Step
LCD Brackets
Size
M2*L3
Quantity
Screw Type
8
6. Remove the LCD brackets by pulling away from the LCD Panel as shown.
Chapter 3
81
Removing the Antennas
1. See “Removing the LCD Panel” on page 80.
2. Remove the strips holding the antenna cables in place. Ensure the cables are free from obstructions.
3. Remove the tab securing the left antenna to the LCD module.
4. Remove the tab securing the right antenna to the LCD module.
5. Remove the antenna cables and assembly from the LCD module.
82
Chapter 3
Removing the MIC Module
1. See “Removing the Antennas” on page 82.
2. Remove the strips holding the MIC Module cable in place. Ensure the cable is free from obstructions.
3. Remove the MIC cable and Module from the LCD module.
NOTE: If the left antenna is present, it may be necessary to lift the assembly to free the Mic cable.
Chapter 3
83
LCD Module Reassembly Procedure
Replacing the LCD Panel
1. Replace the left antenna and cable as shown. Ensure that the cable is inserted under each tab strip.
2. Replace the right antenna and cable as shown. Ensure that the cable is inserted under each tab strip.
3. Replace the MIC cable under antenna and replace the MIC as shown.
84
Chapter 3
4. Replace the securing strips holding the Mic cable in place.
5. Align the LCD brackets as shown. Starting with the top most screws (marked with U) replace the eight
screws (four on each side) in the brackets as shown.
U
U
6. Turn the panel over. Insert the LCD Panel cable into the LCD Panel as shown.
Chapter 3
85
7. Align the LCD Panel cable as shown and press down to engage the adhesive pads.
8. Place the LCD Panel in the back cover.
9. Secure the LCD module with the two securing
screws.
10. Insert the Camera Module right side first to engage 11. Replace the single securing screw.
the securing clip.
86
Chapter 3
12. Connect the Camera Module cable.
13. Connect the right side inverter cable.
14. Connect the left side inverter cable and place the
inverter in the LCD module.
15. Replace the single securing screw and adhesive
tape.
Chapter 3
87
Replacing the LCD Bezel
1. Locate the bezel correctly and press down the edges until there are no gaps between the bezel and the LCD
Module.
2. Replace the four screws and the rubber screw caps provided.
88
Chapter 3
Main Module Reassembly Procedure
Replacing the CPU
1. Carefully turn the mainboard upside down (CPU
2. Using a plastic screw driver, lock the CPU in the
side up), and insert the CPU into the CPU bracket
socket as shown.
as shown.
Replacing the Thermal Module
1. Align and place the Thermal Module in the mounting as shown.
2. Replace the four screws (in numerical order from screw 1 to screw 4) to secure the Thermal Module.
3
1
Chapter 3
2
4
89
Replacing the CPU Fan Module
1. Align the Fan Module on the screw brackets.
2. Replace the three securing screws.
3. Connect the Fan cable to the Mainboard.
Replacing the Mainboard
1. Turn the Mainboard over. Connect the DC IN Cable to the Mainboard.
90
Chapter 3
2. Ensure that the Mainboard is face up (the Heatsink and CPU are not visible). Place the Mainboard in the
chassis, left side first (1), and press down to install (2).
NOTE: Make sure the I/O ports are positioned correctly through the lower cover, and the screw sockets are
visible through the mainboard.
1
2
3. Replace the single securing screw.
4. Press down on the DC IN cable to secure the
adhesive in place.
Replacing the Modem Module
1. Connect the Modem cable to the Modem Module
as shown.
Chapter 3
2. Replace the Modem Module and secure the two
screws as shown.
91
Replacing the Power Board
1. Feed the Power Board FFC thought the upper
base as shown.
2. Place the Power Board on the upper base and
replace the adhesive strip.
3. Turn the upper base over and replace the adhesive strip securing the Power Board FFC in place.
92
Chapter 3
Replacing the Speaker Module
1. Replace the left side speaker in the upper base and secure it using the two screws provided. Install the
speaker cable, taking care to follow the path as shown.
2. Replace the right side speaker in the upper base and secure it using the two screws provided. Install the
speaker cable, taking care to follow the path as shown
3. Replace the Power Board FFC over the speaker cable as shown.
Chapter 3
93
4. Replace the adhesive tape to secure the speaker cable in place.
94
Chapter 3
Replacing the TouchPad Bracket
IMPORTANT:The TouchPad cannot be removed individually. To replace the TouchPad, replace the entire
Upper Cover.
1. Replace the TouchPad bracket bottom edge first to 2. Slide the TouchPad bracket in the direction of the
engage the securing clips.
arrow to engage the securing clip.
3. Replace the two securing screws from the
TouchPad bracket.
4. Replace the TouchPad FFC and press down to
secure with the adhesive strips.
Replacing the Upper Case
1.
Place the upper case on the lower case front edge 2. Lower the case into position, as shown, and press
first.
down around the edges to secure it in place.
Chapter 3
95
3. Reconnect the three cables as shown.
A
B
C
Reconnect A as shown.
Replace the adhesive tape to on cable A.
Reconnect B as shown and secure the cable latch.
Reconnect C as shown and secure the cable latch.
96
Chapter 3
4. Replace the seven screws as shown.
5. Turn the computer over and replace the eight
screws as shown.
Replacing the LCD Module
1. Align the LCD hinges with the lower case and replace the LCD module.
2. Replace the four securing screws (two each side), starting with the left side hinge.
NOTE: Two different screw sizes are used to secure the LCD module in place. The red callouts require
M2.5*8 screws and the blue callouts require M2.5*5 screws.
Chapter 3
97
3. Reconnect the two LCD module interface cables as shown.
4. Replace the protective film over the cables.
98
5. Turn the computer over and replace the two
screws to secure the LCD module in place.
Chapter 3
Replacing the Antenna Cable
IMPORTANT:The antenna cable must run along the supplied cable channels and use all the available cable
clips to avoid damage to components during reassembly.
1. Run the antenna cable along the cable channel
using all the cable clips as shown.
2. Feed the cable through the chassis and pull it
through from the under side of the computer.
Secure the cable in place using the adhesive tape.
3. Turn the computer over and run the cable along the cable channel as shown.
Chapter 3
99
Replacing the Keyboard
1. Reconnect keyboard FFC to the mainboard, and
secure the locking latch.
2. Turn the keyboard over and place the front edge
first in the mounting.
3. Rotate the keyboard downward and press gently in to place.
100
Chapter 3
Replacing the Switch Cover
1. Place the Switch Cover left side first on to the
upper case as shown.
2. Press down along the length of the cover to secure
it in place.
3. Turn the computer over and replace the two securing screws.
Chapter 3
101
Replacing the ODD Module
1. With the ODD tray in the eject position, replace the 2. Press the cover into the tray, bottom edge first, to
ODD cover on the new ODD Module.
secure.
3. Turn ODD Module around and secure bracket with 4. Slide the module in the chassis and press until the
three screws.
module is flush with the chassis.
5. Replace the single screw to secure the Module.
102
Chapter 3
Replacing the Hard Disk Drive Module
1. Place the HDD in the HDD carrier.
2. Replace the four screws to secure the carrier.
3. Insert the HDD, interface side first, and lower it into 4. Slide the HDD to the left to secure in place.
place.
Chapter 3
103
Replacing the WLAN Module
1. Insert the WLAN board into the WLAN socket.
2. Replace the two screws to secure the module.
3. Connect the two antenna cables to the module.
NOTE: The white antenna cable connects to the upper terminal and the black antenna cable to the lower
terminal.
Replacing the DIMM Modules
NOTE: To replace DIMM Module 2, first remove DIMM Module 1. In this procedure, only DIMM Module 1 is
shown.
1. Insert the DIMM Module in place.
104
2. Press down to lock the DIMM module in place.
Chapter 3
Replacing the Lower Covers
1. Replace the Memory Cover.
2. Replace the WLAN Cover.
3. Replace HDD Cover.
4. Replace the three screws in the memory and
WLAN bays and secure the two captive screws in
the HDD cover.
Chapter 3
105
Replacing the Battery
1. Slide and hold the battery release latch to the
release position (1), insert the battery pack and
press down (2).
2. Slide the battery lock/unlock latch to the lock
position.
2
1
106
Chapter 3
Chapter 4
Troubleshooting
Common Problems
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.
Obtain the failing symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power On Issue
Page 108
No Display Issue
Page 109
LCD Failure
Page 111
Internal Keyboard Failure
Page 111
TouchPad Failure
Page 112
Internal Speaker Failure
Page 112
Internal Microphone Failure
Page 114
ODD Failure
Page 116
Modem Failure
Page 119
WLAN Failure
Page 119
Thermal Unit Failure
Page 120
Other Functions Failure
Page 121
Intermittent Failures
Page 122
Undermined Failures
Page 122
4.
If the Issue is still not resolved, see “Online Support Information” on page 161.
Chapter 4
107
Power On Issue
If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Computer Shutsdown Intermittently
If the system powers off at intervals, perform the following actions one at a time to correct the problem.
108
1.
Check the power cable is properly connected to the computer and the electrical outlet.
2.
Remove any extension cables between the computer and the outlet.
3.
Remove any surge protectors between the computer and the electrical outlet. Plug the computer directly
into a known good electrical outlet.
4.
Disconnect the power and open the casing to check the Thermal Unit (see “Thermal Unit Failure” on page
120) and fan airways are free of obstructions.
5.
Disable the power management settings in the BIOS to ensure they are not the cause of the problem (see
“Power” on page 29).
6.
Remove all external and non-essential hardware connected to the computer that are not necessary to
boot the computer to the failure point.
7.
Remove any recently installed software.
8.
If the Issue is still not resolved, see “Online Support Information” on page 161.
Chapter 4
No Display Issue
If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
No POST or Video
If the POST or video doesn’t display, perform the following actions one at a time to correct the problem.
1.
Make sure that the internal display is selected. On this notebook model, switching between the internal
display and the external display is done by pressing Fn+F5. Reference Product pages for specific model
procedures.
2.
Make sure the computer has power by checking at least one of the following occurs:
•
Fans start up
•
Status LEDs light up
If there is no power, see “Power On Issue” on page 108.
3.
Drain any stored power by removing the power cable and battery and holding down the power button for
10 seconds. Reconnect the power and reboot the computer.
4.
Connect an external monitor to the computer and switch between the internal display and the external
display is by pressing Fn+F5 (on this model).
If the POST or video appears on the external display, see “LCD Failure” on page 111.
5.
Disconnect power and all external devices including port replicators or docking stations. Remove any
memory cards and CD/DVD discs. Restart the computer.
If the computer boots correctly, add the devices one by one until the failure point is discovered.
6.
Reseat the memory modules.
7.
Remove the drives (see “Disassembly Process” on page 42).
8.
If the Issue is still not resolved, see “Online Support Information” on page 161.
Chapter 4
109
Abnormal Video Display
If video displays abnormally, perform the following actions one at a time to correct the problem.
1.
Reboot the computer.
2.
If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and
should be replaced. See “Disassembly Process” on page 42.
3.
If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD
is faulty and should be replaced. See “Disassembly Process” on page 42.
4.
Adjust the brightness to its highest level. See the User Manual for instructions on adjusting settings.
NOTE: Ensure that the computer is not running on battery alone as this may reduce display brightness.
If the display is too dim at the highest brightness setting, the LCD is faulty and should be replaced. See
“Disassembly Process” on page 42.
5.
Check the display resolution is correctly configured:
a.
Minimize or close all Windows.
b.
If display size is only abnormal in an application, check the view settings and control/mouse wheel
zoom feature in the application.
c.
If desktop display resolution is not normal, right-click on the desktop and select
Personalize´ Display Settings.
d.
Click and drag the Resolution slider to the desired resolution.
e.
Click Apply and check the display. Readjust if necessary.
6.
Roll back the video driver to the previous version if updated.
7.
Remove and reinstall the video driver.
8.
Check the Device Manager to determine that:
9.
•
The device is properly installed. There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
If the Issue is still not resolved, see “Online Support Information” on page 161.
10. Run the Windows Memory Diagnostic from the operating system DVD and follow the onscreen prompts.
11. If the Issue is still not resolved, see “Online Support Information” on page 161.
Random Loss of BIOS Settings
If the computer is experiencing intermittent loss of BIOS information, perform the following actions one at a
time to correct the problem.
1.
If the computer is more than one year old, replace the CMOS battery.
2.
Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3.
If the computer is experiencing HDD or ODD BIOS information loss, disconnect and reconnect the power
and data cables between devices.
If the BIOS settings are still lost, replace the cables.
110
4.
If HDD information is missing from the BIOS, the drive may be defective and should be replaced.
5.
Replace the Motherboard.
6.
If the Issue is still not resolved, see “Online Support Information” on page 161.
Chapter 4
LCD Failure
If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
Built-In Keyboard Failure
If the built-in Keyboard fails, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
Chapter 4
111
TouchPad Failure
If the TouchPad doesn’t work, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Internal Speaker Failure
If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
112
Chapter 4
Sound Problems
If sound problems are experienced, perform the following actions one at a time to correct the problem.
1.
Reboot the computer.
2.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager. Check
the Device Manager to determine that:
•
The device is properly installed.
•
There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
3.
Roll back the audio driver to the previous version, if updated recently.
4.
Remove and reinstall the audio driver.
5.
Ensure that all volume controls are set mid range:
a.
Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted.
b.
Click Mixer to verify that other audio applications are set to 50 and not muted.
6.
Navigate to Start´ Control Panel´ Hardware and Sound´ Sound. Ensure that Speakers are selected
as the default audio device (green check mark).
NOTE: If Speakers does not show, right-click on the Playback tab and select Show Disabled Devices
(clear by default).
7.
Select Speakers and click Configure to start Speaker Setup. Follow the onscreen prompts to configure
the speakers.
8.
Remove and recently installed hardware or software.
9.
Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
10. Reinstall the Operating System.
11. If the Issue is still not resolved, see “Online Support Information” on page 161.
Chapter 4
113
Internal Microphone Failure
If the internal Microphone fails, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Microphone Problems
If internal or external Microphones do no operate correctly, perform the following actions one at a time to
correct the problem.
1.
Check that the microphone is enabled. Navigate to Start´ Control Panel´ Hardware and Sound´
Sound and select the Recording tab.
2.
Right-click on the Recording tab and select Show Disabled Devices (clear by default).
3.
The microphone appears on the Recording tab.
4.
Right-click on the microphone and select Enable.
5.
Select the microphone then click Properties. Select the Levels tab.
6.
Increase the volume to the maximum setting and click OK.
7.
Test the microphone hardware:
8.
114
a.
Select the microphone and click Configure.
b.
Select Set up microphone.
c.
Select the microphone type from the list and click Next.
d.
Follow the onscreen prompts to complete the test.
If the Issue is still not resolved, see “Online Support Information” on page 161.
Chapter 4
HDD Not Operating Correctly
If the HDD does not operate correctly, perform the following actions one at a time to correct the problem.
1.
Disconnect all external devices.
2.
Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3.
Run the Windows Vista Startup Repair Utility:
a.
insert the Windows Vista Operating System DVD in the ODD and restart the computer.
b.
When prompted, press any key to start to the operating system DVD.
c.
The Install Windows screen displays. Click Next.
d.
Select Repair your computer.
e.
The System Recovery Options screen displays. Click Next.
f.
Select the appropriate operating system, and click Next.
NOTE: Click Load Drivers if controller drives are required.
g.
Select Startup Repair.
h.
Startup Repair attempts to locate and resolve issues with the computer.
i.
When complete, click Finish.
If an issue is discovered, follow the onscreen information to resolve the problem.
4.
Run the Windows Memory Diagnostic Tool. For more information see Windows Help and Support.
5.
Restart the computer and press F2 to enter the BIOS Utility. Check the BIOS settings are correct and that
CD/DVD drive is set as the first boot device on the Boot menu.
6.
Ensure all cables and jumpers on the HDD and ODD are set correctly.
7.
Remove any recently added hardware and associated software.
8.
Run the Windows Disk Defragmenter. For more information see Windows Help and Support.
9.
Run Windows Check Disk by entering chkdsk /r from a command prompt. For more information see
Windows Help and Support.
10. Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
11. Replace the HDD. See “Disassembly Process” on page 42.
Chapter 4
115
ODD Failure
If the ODD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
ODD Not Operating Correctly
If the ODD exhibits any of the following symptoms it may be faulty:
•
Audio CDs do not play when loaded
•
DVDs do not play when loaded
•
Blank discs do not burn correctly
•
DVD or CD play breaks up or jumps
•
Optical drive not found or not active:
•
Not shown in My Computer or the BIOS setup
•
LED does not flash when the computer starts up
•
The tray does not eject
•
Access failure screen displays
•
The ODD is noisy
Perform the following general solutions one at a time to correct the problem.
116
1.
Reboot the computer and retry the operation.
2.
Try an alternate disc.
3.
Navigate to Start´ Computer. Check that the ODD device is displayed in the Devices with Removable
Storage panel.
4.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
Chapter 4
a.
Double-click lDE ATA/ATAPI controllers. If a device displays a down arrow, right-click on the device
and click Enable.
b.
Double-click DVD/CD-ROM drives. If the device displays a down arrow, right-click on the device and
click Enable.
c.
Check that there are no yellow exclamation marks against the items in lDE ATA/ATAPI controllers. If
a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
d.
Check that there are no yellow exclamation marks against the items in DVD/CD-ROM drives. If a
device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
e.
If the exclamation marker is not removed from the item in the lists, try removing any recently installed
software and retrying the operation.
Discs Do Not Play
If discs do not play when inserted in the drive, perform the following actions one at a time to correct the
problem.
1.
Check that the disc is correctly seated in the drive tray and that the label on the disc is visible.
2.
Check that the media is clean and scratch free.
3.
Try an alternate disc in the drive.
4.
Ensure that AutoPlay is enabled:
5.
a.
Navigate to Start´ Control Panel´ Hardware and Sound´ AutoPlay.
b.
Select Use AutoPlay for all media and devices.
c.
In the Audio CD and DVD Movie fields, select the desired player from the drop down menu.
Check that the Regional Code is correct for the selected media:
IMPORTANT:Region can only be changed a limited number of times. After Changes remaining reaches zero,
the region cannot be changed even Windows is reinstalled or the drive is moved to another computer.
a.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
b.
Double-click DVD/CD-ROM drives.
c.
Right-click DVD drive and click Properties, then click the DVD Region tab.
d.
Select the region suitable for the media inserted in the drive.
Discs Do Not Burn Properly
If discs can not be burned, perform the following actions one at a time to correct the problem.
1.
2.
Ensure that the default drive is record enabled:
a.
Navigate to Start´ Computer and right-click the writable ODD icon. Click Properties.
b.
Select the Recording tab. In the Desktop disc recording panel, select the writable ODD from the
drop down list.
c.
Click OK.
Ensure that the software used for burning discs is the factory default. If using different software, refer to
the software's user manual.
Playback is Choppy
If playback is choppy or jumps, perform the following actions one at a time to correct the problem.
1.
2.
Check that system resources are not running low:
a.
Try closing some applications.
b.
Reboot and try the operation again.
Check that the ODD controller transfer mode is set to DMA:
a.
Chapter 4
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
117
b.
Double-click IDE ATA/ATAPI controllers, then right-click ATA Device 0.
c.
Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is
checked and click OK.
d.
Repeat for the other ATA Devices shown if applicable.
Drive Not Detected
If Windows cannot detect the drive, perform the following actions one at a time to correct the problem.
1.
Restart the computer and press F2 to enter the BIOS Utility.
2.
Check that the drive is detected in the ATAPI Model Name field on the Information page.
NOTE: Check that the entry is identical to one of the ODDs specified in “Hardware Specifications and
Configurations” on page 16.
3.
Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 42.
a.
Check for broken connectors on the drive, motherboard, and cables.
b.
Check for bent or broken pins on the drive, motherboard, and cable connections.
c.
Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
4.
Reseat the drive ensuring and all cables are connected correctly.
5.
Replace the ODD. See “Disassembly Process” on page 42.
Drive Read Failure
If discs cannot be read when inserted in the drive, perform the following actions one at a time to correct the
problem.
1.
Remove and clean the failed disc.
2.
Retry reading the CD or DVD.
d.
Test the drive using other discs.
e.
Play a DVD movie
f.
Listen to a music CD
If the ODD works properly with alternate discs, the original disc is probably defective and should be
replaced.
3.
4.
118
Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 42.
a.
Check for broken connectors on the drive, motherboard, and cables.
b.
Check for bent or broken pins on the drive, motherboard, and cable connections.
c.
Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
Replace the ODD. See “Disassembly Process” on page 42.
Chapter 4
Modem Function Failure
If the internal Modem fails, perform the following actions one at a time to correct the problem. Do not replace a
non-defective FRUs:
Wireless Function Failure
If the WLAN fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
Chapter 4
119
Thermal Unit Failure
If the Thermal Unit fails, perform the following actions one at a time to correct the problem. Do not replace a
non-defective FRUs:
External Mouse Failure
If an external Mouse fails, perform the following actions one at a time to correct the problem.
1.
Try an alternative mouse.
2.
If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See
the mouse user manual.
3.
If the mouse uses a USB connection, try an alternate USB port.
4.
Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure.
5.
Restart the computer.
6.
Remove any recently added hardware and associated software.
7.
Remove any recently added software and reboot.
8.
Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
9.
Run the Event Viewer to check the events log for errors. For more information see Windows Help and
Support.
10. Roll back the mouse driver to the previous version if updated recently.
11. Remove and reinstall the mouse driver.
12. Check the Device Manager to determine that:
120
•
The device is properly installed. There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
Chapter 4
•
No hardware is listed under Other Devices.
13. If the Issue is still not resolved, see “Online Support Information” on page 161.
Other Failures
If the CRT Switch, Dock, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or
Volume Wheel fail, perform the following general steps to correct the problem. Do not replace a non-defective
FRUs:
1.
Check Drive whether is OK.
2.
Check Test Fixture is ok.
3.
Swap M/B to Try.
Chapter 4
121
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power On
Issue” on page 108.):
122
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
•
Non-Acer devices
•
Printer, mouse, and other external devices
•
Battery pack
•
Hard disk drive
•
DIMM
•
CD-ROM/Diskette drive Module
•
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
•
System board
•
LCD assembly
Chapter 4
Post Codes
These tables describe the POST codes and descriptions during the POST.
Sec:
NO_EVICTION_MODE_DEBUG EQU 1 (CommonPlatform\sec\Ia32\SecCore.inc)
Code
Description
0xC2
MTRR setup
0xC3
Enable cache
0xC4
Establish cache tags
0xC5
Enter NEM, Place the BSP in No Fill mode, set CR0.CD = 1, CR0.NW = 0
0xCF
Cache Init Finished
Memory:
DEBUG_BIOS equ 1 (Chipset\Alviso\MemoryInitAsm\IA32\IMEMORY.INC)
Code
Description
0xA0
First memory check point
0x01
Enable MCHBAR
0x02
Check for DRAM initialization interrupt and reset fail
0x03
Verify all DIMMs are DDR or DDR2 and unbuffered
0x04
Detect an improper warm reset and handle
0x05
Detect if ECC SO-DIMMs are present in the system
0x06
Verify all DIMMs are single or double sided and not asymmetric
0x07
Verify all DIMMs are x8 or x16 width
0x08
Find a common CAS latency between the DIMMS and the MCH
0x09
Determine the memory frequency and CAS latency to program
0x10
Determine the smallest common TRAS for all DIMMs
0x11
Determine the smallest common TRP for all DIMMs
0x12
Determine the smallest common TRCD for all DIMMs
0x13
Determine the smallest refresh period for all DIMMs
0x14
Verify burst length of 8 is supported by all DIMMs
0x15
Determine the smallest tWR supported by all DIMMs
0x16
Determine DIMM size parameters
0x17
Program the correct system memory frequency
0x18
Determine and set the mode of operation for the memory channels
0x19
Program clock crossing registers
0x20
Disable Fast Dispatch
0x21
Program the DRAM Row Attributes and DRAM Row Boundary registers
0x22
Program the DRAM Bank Architecture register
0x23
Program the DRAM Timing & and DRAM Control registers
0x24
Program ODT
0x25
Perform steps required before memory init
0x26
Program the receive enable reference timing control register
Program the DLL Timing Control Registers, RCOMP settings
Chapter 4
123
Code
Description
0x27
Enable DRAM Channel I/O Buffers
0x28
Enable all clocks on populated rows
0x29
Perform JEDEC memory initialization for all memory rows
0x30
Perform steps required after memory init
0x31
Program DRAM throttling and throttling event registers
0x32
Setup DRAM control register for normal operation and enable
0x33
Enable RCOMP
0x34
Clear DRAM initialization bit in the SB
0x35
Initialization Sequence Completed, program graphic clocks
0x43
Program Thermal Throttling
BDS & Specific action:
Code
124
Description
0x00
Report the legacy boot is happening
0x12
Wake up the Aps
0x13
Initialize SMM Private Data and relocate BSP SMBASE
0x21
PC init begin at the stage1
0x27
Report every memory range do the hard ware ECC init
0x28
Report status code of every memory range
0x50
Get the root bridge handle
0x51
Notify pci bus driver starts to program the resource
0x58
Reset the host controller
0x5A
IdeBus begin initialization
0x79
Report that the remote terminal is being disabled
0x7A
Report that the remote terminal is being enabled
0x90
Keyboard reset
0x91
USB Keyboard disable
0x92
Keyboard detection
0x93
Report that the usb keyboard is being enabled
0x94
Clear the keyboard buffer
0x95
Init Keyboard
0x98
Mouse reset
0x99
Mouse disable
0x9A
Detect PS2 mouse
0x9B
Report that the mouse is being enabled
0xB8
Peripheral removable media reset (ex: IsaFloppy, USB device)
0xB9
Peripheral removable media disable
0xBB
Peripheral removable media enable
0xE4
Report Status Code here for DXE_ENTRY_POINT once it is available
0xF8
Report that ExitBootServices() has been called
0xF9
Runtime driver set virtual address map
Chapter 4
Each PEIM entry point used in 80_PORT
Code
Description
0x00
0x01
PEI_EVENT_LOG
0xA1
PEI_OEM_SERVICE
0xA2
PEI_SIO_INIT
0xA3
PEI_MONO_STATUS_CODE
0xA4
PEI_CPU_IO_PCI_CFG
0x06
PEI_CPU_IO
0x07
PEI_PCI_CFG
0xA5
PEI_CPU_PEIM
0xA6
PEI_PLATFORM_STAGE1
0xA7
PEI_VARIABLE
0xA8
PEI_SB_INIT
0x0C
PEI_CAPSULE
0xAA
PEI_PLATFORM_STAGE2
0xAC
PEI_SB_SMBUS_ARP_DISABLED
0x0F
PEI_HOST_TO_SYSTEM
0x40
PEI_MEMORY_INIT
0x41
PEI_S3_RESUME
0xAD
PEI_CLOCK_GEN
0xAB
PEI_OP_PRESENCE
0xAE
PEI_FIND_FV
0x16
PEI_H2O_DEBUG_IO
0x17
PEI_H2O_DEBUG_COMM
0x16~0x1F
PEI_RESERVED
0x20~0x2E
PEI_OEM_DEFINED
0xAF
PEI_DXE_IPL
Each Driver entry point used in 80_PORT
Code
Description
0x30
RESERVED
0xB6
DXE_CRC32_SECTION_EXTRACT
0xB8
SCRIPT_SAVE
0xB9
ACPI_S3_SAVE
0xBA
SMART_TIMER
0xBB
JPEG_DECODER
0xBC
PCX_DECODER
0xBE
HT_CPU / MP_CPU
0xBF
LEGACY_METRONOME
0xC0
FTWLITE
0xC1
RUN_RIME
0xC2
MONOTONIC_COUNTER
0xC3
WATCH_DOG_TIMER
Chapter 4
125
Code
126
Description
0xC4
SECURITY_STUB
0xC5
DXE_CPU_IO
0xC6
CF9_RESET
0xC7
PC_RTC
0xC8
STATUS_CODE
0xC9
VARIABLE
EMU_VARIABLE
0xD9
DXE_CHIPSET_INIT
0x45
DXE_ALERT_FORMAT
0xD6
PCI_HOST_BRIDGE
0xD7
PCI_EXPRESS
0xD5
DXE_SB_INIT
0xDA
IDE_CONTROLLER
0xDB
SATA_CONTROLLER
0xDD
SB_SM_BUS
0xE7
ISA_ACPI_DRIVER
0xE8
ISA_BUS
0xE9
ISA_SERIAL
0xED
BUS_PCI_UNDI
0xEC
PCI_BUS
0xF6
BOOT_PRIORITY
0xF7
FVB_SERVICE
0xF8
ACPI_PLATFORM
0xFB
PCI_HOT_PLUG
0xFC
DXE_PLATFORM
0xFD
PLATFORM_IDE
0x97
SMBIOS
0x98
MEMORY_SUB_CLASS
0x99
MISC_SUB_CLASS
0x82
CON_PLATFORM
0x83
SAVE_MEMORY_CONFIG
0x84
ACPI_SUPPORT
0x85
CON_SPLITTER_UGA_VGA / CON_SPLITTER
0x88
VGA_CLASS
0x89
DATA_HUB
0x60
DISK_IO
0x8B
MEMORY_TEST
0x62
CRISIS_RECOVERY
0x8D
LEGACY_8259
0x8E
LEGACY_REGION
0x8F
LEGACY_INTERRUPT
0x70
BIOS_KEYBOARD
0x71
BIOS_VEDIO
Chapter 4
Code
Description
0x72
MONITER_KEY
0x73
LEGACY_BIOS
0x75
LEGACY_BIOS_PLATFORM
0x76
PCI_PLATFORM
0x6C
ISA_FLOOPY
0x6D
PS2_MOUSE
0x6E
USB_BOT
0x6F
USB_CBI0
0x74
USB_MOUSE
0xFA
SETUP_UTILITY
0x90
FW_BLOCK_SERVICE
0x78
SMM_USB_LEGACY
0x86
GRAPHICS_CONSOLE
0x87
TERMINAL
0x8A
DATA_HUB_STD_ERR
0x7C
FAT
0x7D
PARTITION
0x7E
ENGLISH
0x7F
FRENCH
0x9E
HII_DATABASE
0x9F
OEM_SETUP_BROWSER
0x8C
OEM_BADGING_SUPPORT
0xF9
SETUP_MOUSE
0x72
MONITOR_KEY
0xBD
PLATFORM_BDS
0x8D
RESERVED
0x8E
RESERVED
0x8F
RESERVED
0xA0
DXE_H2O_DEBUG_IO
0xB3
DXE_TPM_TCG
0xB4
DXE_TPM_PHYSICAL_PRESENCE
0xB7
DXE_OEM_SERVICE
0x9B
DXE_ SECURITY_HDD_PASSWORD_SERVICE
0xA9
DXE_LAN_IDER_CONTROLLER
0x9C
DXE_ SECURITY_SYSTEM_PASSWORD_SERVICE
0x9D
DXE_ SECURITY_ PASSWORD_CONSOLE
0xCB
DXE_ DATA_HUB_RECORD_POLICY
0xB5
DXE_TPM_DRIVER
0x11
CHINESE
0xB0
JAPANESE
0xB1
DXE_UNICODE_COLLACTION
Chapter 4
127
Each SmmDriver entry point used in 80_PORT
Code
128
Description
0xD4
SMM_ACCESS
0xDE
SMM_CONTROL
0xCC
SMM_BASE
0xD2
SMM_RUNTIME
0xDF
SB_SMM_DISPATCH
0xD0
SMM_THUNK
0xCA
SMM_ACPI_SW_CHILD
0xFE
SMM_PLATFORM
0xD8
SMM_GMCH_MBI
0x90
SMM_FW_BLOCK_SERVICE
0x91
SMM_VARIABLE
0x92
SMM_IHISI
0x93
SMM_INT15_MICROCODE
0x94
SMM_PNP
0x95
SMM_INIT_PPM
0xD3
SMM_OEM_SERVICE
Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
Item
Chapter 5
Description
Item
Description
SW4
Wireless LAN Button
JP1
Internal MIC Connector
JLVDS1
LCD Connector
JP5
Fun/B Connector
JP3
Speaker Connector
JP4
Keyboard Connector
JP6
Power/B Connector
U9
South Bridge
JP7
TouchPad Connector
LED1
Power/SUSP LED
LED2
Battery LED
SW2
TouchPad (left) Button
SW3
TouchPad (right) Button
129
Bottom View
Item
130
Description
Item
Description
JCPU1
CPU Socket
JCRT1
CRT Connector
JDIMM1
Memory DIMM1 Connector
JDIMM2
Memory DIMM2 Connector
JHP1
Head-Phone Connector
JLINE1
Line-In Jack
JMIC1
MIC-In Jack
JMINI2
Wireless Card Connector
JP12
Fan Connector
JRJ45
RJ45 Connector
JSATA1
ODD Connector
JSATA2
HDD Connector
JUSB1
USB Connector
JUSB2
USB Connector
PJP1
AC-IN Connector
PJP2
Battery Connector
U31
North Bridge
Chapter 5
Clearing Password Check and BIOS Recovery
This section provide you the standard operating procedures of clearing password and BIOS recovery for
eMachines D720/D520 Series. eMachines D720/D520 provide one Hardware Open Gap on main board for
clearing password check, and one Hotkey for enabling BIOS Recovery.
Clearing Password Check
Hardware Open Gap Description
Item
R347 (RTC_RST)
Description
Clear CMOS Jumper
Steps for Clearing BIOS Password Check
If users set BIOS Password (Supervisor Password and/or User Password) for a security reason, BIOS will ask
the password during systems POST or when systems enter to BIOS Setup menu. However, once it is
necessary to bypass the password check, users need to short the HW Gap to clear the password by the
following steps:
•
Power Off a system, and remove HDD, AC and Battery from the machine.
•
Open the back cover of the machine, and find out the HW Gap on M/B as picture.
•
Use an electric conductivity tool to short the two points of the HW Gap.
•
Plug in AC, keep the short condition on the HW Gap, and press Power Button to power on the
system till BIOS POST finish. Then remove the tool from the HW Gap.
•
Restart system. Press F2 key to enter BIOS Setup menu.
If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and
try again.
NOTE: The steps are only for clearing BIOS Password (Supervisor Password and User Password).
•
Chapter 5
131
BIOS Recovery by Crisis Disk
BIOS Recovery Boot Block:
BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS
initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous
BIOS flashing process failed.
BIOS Recovery Hotkey:
The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered
on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery
present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called Boot
Block.
Steps for BIOS Recovery from USB Storage:
Before doing this, prepare the Crisis USB key. The Crisis USB key could be made by executing the Crisis Disk
program in another system with Windows XP OS.
Follow the steps below:
1.
Save ROM file (file name: JAL90x64.fd) to the root directory of USB storage.
2.
Plug USB storage into USB port.
3.
Press Fn + ESC button then plug in AC.
The Power button flashes once.
4.
Press Power button to initiate system CRISIS mode.
When CRISIS is complete, the system auto restarts with a workable BIOS.
5.
132
Update the latest version BIOS for this machine by regular BIOS flashing process.
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of eMachines D720/D520. Refer to
this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service
Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from
those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to
dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6
133
eMachines D720/D520 Exploded Diagrams
Main Assembly
5
6
1
7
2
8
3
9
10
11
4
No.
Description
Acer P/N
No.
Description
1
Mini Door
7
Power Board
2
HDD Door
8
Upper Case
3
Ram Door
9
Mainboard
4
Lower Case
10
CPU Fan
5
Middle Cover
11
Heatsink
6
Keyboard
134
Acer P/N
Chapter 6
LCD Panel
1
2
3
8
4
9
5
6
10
7
No.
Description
11
Acer P/N
No.
Description
1
LCD Bezel
7
Camera Module
2
LCD Panel
8
Right Antenna
3
Left Antenna
9
Right Hinge
4
LCD Cable
10
Inverter
5
Left Hinge
11
LCD Assembly
6
Mic Cable
Chapter 6
Acer P/N
135
eMachines D720/D520 FRU List
Category
Description
Acer Part No.
Adapter
ADAPTER 65W 3PIN DELTA SADP65KB BFJA OBL
AP.06501.014
ADAPTER 65W 3PIN DELTA SADP-65KB DFA
AP.06501.013
ADAPTER 65W 3PIN LITEON PA-1650-02AC
TBD
ADAPTER 65W 3PIN HIPRO AC-OK065B13
TBD
Battery
BATTERY LI-ION 6CELLS 4.4AH SANYO
BT.00603.041
BATTERY LI-ION 6CELLS 4.4AH SONY
BT.00604.024
BATTERY LI-ION 6CELLS SP SM 3S2P 4.4AH SIMPLO
BT.00607.034
BATTERY LI-ION 6CELLS SP SM 3S2P 4.8AH SIMPLO
TBD
BATTERY LI-ION 6CELLS SP LG 3S2P 4.4AH SIMPLO
TBD
BATTERY LI-ION 6CELLS SP PA 3S2P 4.4AH 7 043 0FA
SIMPLO
BT.00607.015
BATTERY LI-ION 6CELLS 4.4AH PANASONIC
BT.00605.020
POWER BOARD
55.N0902.001
MODEM BOARD
55.N0902.002
MINI CARD BROADCOM T77H030.00 54MBPS BRCM4312
NI.23600.029
MINI CARD ATHEROS T60H976.00 (FW-06) 54M XB63
NI.23600.007
T/P FFC
50.N0902.001
POWER CORD US 3 PIN
27.TAVV5.001
Board
Cable
POWER CORD EU 3 PIN
27.TAVV5.002
POWER CORD AUS 3 PIN
27.TAVV5.003
POWER CORD UK 3 PIN
27.TAVV5.004
POWER CORD CHINA 3 PIN
27.TAVV5.005
POWER CORD SWISS 3 PIN
27.TAVV5.006
POWER CORD ITALIAN 3 PIN
27.TAVV5.007
POWER CORD DENMARK 3 PIN
27.TAVV5.008
POWER CORD JP 3 PIN
27.TAVV5.009
POWER CORD SOUTH AFRICA 3 PIN
27.TAVV5.010
POWER CORD KOERA 3 PIN
27.TAVV5.011
POWER CORD ISRAEL 3 PIN
27.TAVV5.012
POWER CORD INDIA 3 PIN
27.TAVV5.013
POWER CORD TWN 3 PIN
27.TAVV5.014
POWER CORD ARGENTINA 3 PIN
27.APV02.001
Case/Cover/ Bracket Assembly
MIDDLE COVER
136
60.N0902.001
UPPER CASE ASSY
60.N0902.002
LOWER CASE ASSY W/ RJ11
60.N0902.003
LOWER CASE ASSY W/O RJ11
60.N0902.004
T/P BRACKET
33.N0902.001
Chapter 6
Category
Description
Acer Part No.
RAM DOOR
42.N0902.001
MINI DOOR
42.N0902.002
HDD DOOR
42.N0902.003
CPU/Processor
CPU INTEL P575 2G LF80537NF0411M SLB6M M0
CPU INTEL P585 2.16G LF80537NF0481M SLB6L M0
CPU INTEL T1600 1.66G LF80537NF0281MN SLB6J M0
CPU INTEL T1700 1.83G LF80537NF0341MN SLB6H M0
CPU INTEL T3200 2G LF80537GF0411M SLAVG M0
CPU INTEL T3400 2.16G LF80537GF0481M SLB3P M0
Multi Drive
DVD SUPER MULTI DRIVE MODEL
6M.N0902.001
DVD SUPER MULTI DRIVE HLDS GSA-T50N
KU.0080D.029
DVD SUPER MULTI DRIVE HLDS GSA-T50N (ML)
KU.0080D.034
DVD SUPER MULTI DRIVE PIONEER DVR-TD08RS
KU.00805.044
DVD SUPER MULTI DRIVE PLDS DS-8A2S
KU.0080F.001
DVD SUPER MULTI DRIVE SONY AD-7560S
KU.0080E.009
DVD SUPER MULTI DRIVE TOSHIBA TS-L633A
KU.00801.021
ODD BEZEL-SUPER MULTI
42.N0902.004
ODD BRACKET
33.N0902.002
DVD/CDRW COMBO DRIVE MODULE
6M.N0902.002
DVD/CDRW COMBO DRIVE TSST TS-L463A
KO.02401.006
DVD/CDRW COMBO DRIVE SONY CRX890S
KO.0240E.009
ODD BEZEL-COMBO
42.N0902.005
ODD BRACKET
33.N0902.002
Combo Drive
HDD
Chapter 6
137
Category
Description
Acer Part No.
HDD SATA 120G 5400RPM HGST HTS542512K9SA00
KH.12007.014
HDD SATA 120G 5400RPM TOSHIBA MK1246GSX 0FA
KH.12004.007
HDD SATA 120G 5400RPM SEAGATE ST9120817AS
KH.12001.032
HDD SATA 120G 5400RPM WD WD1200BEVS-22UST0
KH.12008.019
HDD SATA 160G 5400RPM HGST HTS542516K9SA00
KH.16007.016
HDD SATA 160G 5400RPM HGST HTS543216L9A300
KH.16007.019
HDD SATA 160G 5400RPM TOSHIBA MK1646GSX
KH.16004.002
HDD SATA 160G 5400RPM SEAGATE ST9160827AS
KH.16001.029
HDD SATA 160G 5400RPM SEAGATE ST9160310AS
KH.16001.034
HDD SATA 160G 5400RPM WD WD1600BEVT-22ZCT0
KH.16008.022
HDD SATA 250G 5400RPM HGST HTS542525K9SA00
KH.25007.011
HDD SATA 250G 5400RPM TOSHIBA MK2546GSX
KH.25004.001
HDD SATA 250G 5400RPM SEAGATE ST9250827AS
KH.25001.011
HDD SATA 250G 5400RPM WD WD2500BEVS-22UST0
KH.25008.018
HDD SATA 320G 5400RPM HGST HTS543232L9A300
KH.32007.004
HDD SATA 320G 5400RPM SEAGATE ST9320320AS
KH.32001.008
HDD SATA 320G 5400RPM WD WD3200BEVT-22ZCT0
KH.32008.013
HDD CARRIER
33.N0902.003
Keyboard
138
Chapter 6
Category
Description
Acer Part No.
KEYBOARD INTE(UI) US INTERNATION
KEYBOARD (ARE) ARABIC ENGLISH
KEYBOARD (BE) BELGIAN
KEYBOARD (BZ) BRAZILIAN
KEYBOARD (CF) CANADIAN FRENCH
KEYBOARD (CH) T-CHINESE
KEYBOARD (DM) DENMARK
KEYBOARD (NL) NETHERLANDS
KEYBOARD (FR) FRENCH
KEYBOARD (GR) GERMAN
KEYBOARD (GK) GREEK
KEYBOARD (HG) HUNGARY
KEYBOARD (IT) ITALIAN
KEYBOARD (KO) KOREAN
KEYBOARD (NW) NORWEGIAN
KEYBOARD (PO) PORTUGUESE
KEYBOARD (RU) RUSSIAN
KEYBOARD (SA/CR) SLOVENIAN
KEYBOARD (SV) SLOVAK
KEYBOARD (SP) SPANISH
KEYBOARD (CZ/SK) CZECH-SLOVAKIAN
KEYBOARD (SW) SWITZERLAND
KEYBOARD (TI) THAILAND
KEYBOARD (TR) TURKISH
KEYBOARD UK
KEYBOARD (HB) HEBREW
KEYBOARD (ND) SCANDINAVIAN
KEYBOARD (AR/FR) ARABIC/FRENCH
KEYBOARD (CB) CANADIAN BILINGUAL
KEYBOARD (SD) SWEDISH
LCD
Chapter 6
ASSY LCD MODULE 14.1 IN. WXGA GLARE W/ANTENNA CCD
6M.N0902.003
LCD PANEL G 14.1" WXGA AUO B141EW04 V4
LK.14105.018
LCD PANEL G 14.1" WXGA SAMSUNG LTN141W3-L01-J
LK.14106.014
LCD PANEL G 14.1" WXGA CMO N141I3-L02
LK.1410D.016
LCD PANEL G 14.1" WXGA LPL LP141WX3-TLN1
LK.14108.014
INVERTER BOARD
19.N0902.001
LCD CABLE
50.N0902.002
ANTENNA-R
50.N0902.003
ANTENNA-L
50.N0902.004
LCD COVER
60.N0902.005
LCD BEZEL
60.N0902.006
LCD BRACKET-R
33.N0902.004
139
Category
Description
Acer Part No.
LCD BRACKET-L
33.N0902.005
CAMERA MODULE 0.3M
57.N0902.001
SCREW PAD
47.N0902.001
MAINBOARD EMD720/EMD520 INTEL GL40 ICH9
PROPRIETARY V1.0 LF
MB.N0902.001
RAM 512MB DDRII 667 NANYA NT512T64UH8B0FN-3C
KN.51203.032
Mainboard
Memory
RAM 512MB DDRII 667 SAMSUNG M470T6464QZ3-CE6
KN.5120B.026
RAM 512MB DDRII 667 HYNIX HYMP164S64CP6-Y5
KN.5120G.024
RAM 1GB DDRII 667 NANYA NT1GT64U8HB0BN-3C
KN.1GB03.014
RAM 1GB DDRII 667 SAMSUNG M470T2864QZ3-CE6
KN.1GB0B.016
RAM 1GB DDRII 667 HYNIX HYMP112S64CP6-Y5
KN.1GB0G.012
RAM 2GB DDRII 667 HYNIX HYMP125S64CP8-Y5
KN.2GB0G.004
RAM 2GB DDRII 667 SAMSUNG M470T5663QZ3-CE6
KN.2GB0B.003
FAN
23.N0902.001
CPU THERMAL MODULE
60.N0902.007
Fan
Heatsink
Speaker
MIC SET
23.N0902.002
SPEAKER R&L
23.N0902.003
NAME PLATE-D520
40.N0902.001
NAME PLATE-D720
40.N0902.002
RUBBER FOOT-L
47.N0902.002
RUBBER FOOT-S
47.N0902.003
RUBBER FOOT-HDD DOOR
47.N0902.004
Miscellaneous
Screw List
Category
Description
Acer Part No.
SCREW
SCREW,M2.5X8(NL)
86.AT902.001
SCREW
SCREW,M2.5X5(NL)
86.AT902.002
SCREW
SCREW,M2X3(NL)
86.AT902.003
SCREW
SCREW,M2.5X4(NL)
86.AT902.004
SCREW
SCREW,M2X4-NI(NL)
86.AT902.005
SCREW
SCREW,M3X3(NL)
86.AT902.006
SCREW
SCREW,M2.5X6.5(NL)
86.AT902.007
140
Chapter 6
Chapter 6
141
Appendix A
Model Definition and Configuration
eMachines D720/D520 Series
Model Description
Model
RO
Country
Acer Part No
Description
eMD520571G12Mi
PA
Canada
LX.N110C.004
eMD520-571G12Mi LINPUSeCA1 UMA
1*1G/120/6L/CB_bg_EN31
eMD520571G12Mi
PA
USA
LX.N110C.003
eMD520-571G12Mi LINPUSeUS1 UMA
1*1G/120/6L/CB_bg_EN31
eMD520571G12Mi
PA
ACLAPortuguese
LX.N110C.002
eMD520-571G12Mi LINPUSeXC1 UMA
1*1G/120/6L/CB_bg_EN61
eMD520571G12Mi
PA
ACLA-Spanish
LX.N110C.001
eMD520-571G12Mi LINPUSeEA3 UMA
1*1G/120/6L/CB_bg_EN61
eMD520571G12Mi
EMEA
Eastern Europe
LX.N110Y.052
eMD520-571G12Mi VHB32eTEU6 UMA
1*1G/120/6L/CB_bg_CS21
eMD520571G12Mi
EMEA
Hungary
LX.N110Y.050
eMD520-571G12Mi VHB32eTHU1 UMA
1*1G/120/6L/CB_bg_HU11
eMD520571G12Mi
EMEA
Slovenia/
Croatia
LX.N110Y.051
eMD520-571G12Mi VHB32eTSI1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
EMEA
Portugal
LX.N110Y.049
eMD520-571G12Mi VHB32eTPT1 UMA
1*1G/120/6L/CB_bg_PT11
eMD520571G12Mi
EMEA
Spain
LX.N110Y.048
eMD520-571G12Mi VHB32eTES1 UMA
1*1G/120/6L/CB_bg_ES21
eMD520571G12Mi
EMEA
Greece
LX.N110Y.044
eMD520-571G12Mi VHB32eTGR1 UMA
1*1G/120/6L/CB_bg_EL21
eMD520571G12Mi
EMEA
Israel
LX.N110Y.045
eMD520-571G12Mi VHB32eTIL1 UMA
1*1G/120/6L/CB_bg_HE11
eMD520571G12Mi
EMEA
Italy
LX.N110Y.046
eMD520-571G12Mi VHB32eTIT1 UMA
1*1G/120/6L/CB_bg_IT11
eMD520571G12Mi
EMEA
Turkey
LX.N110Y.043
eMD520-571G12Mi EM VHB32eTTR1
UMA 1*1G/120/6L/CB_bg_TR41
eMD520571G12Mi
EMEA
Turkey
LX.N110Y.047
eMD520-571G12Mi EM VHB32eTTR1
UMA 1*1G/120/6L/CB_bg_TR11
eMD520571G12Mi
EMEA
Middle East
LX.N110Y.042
eMD520-571G12Mi EM VHB32eTME9
UMA 1*1G/120/6L/CB_bg_FR21
eMD520571G12Mi
EMEA
Middle East
LX.N110Y.040
eMD520-571G12Mi EM VHB32eTME2
UMA 1*1G/120/6L/CB_bg_AR21
eMD520571G12Mi
EMEA
Middle East
LX.N110Y.041
eMD520-571G12Mi EM VHB32eTME6
UMA 1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
EMEA
Middle East
LX.N110Y.039
eMD520-571G12Mi EM VHB32eTME3
UMA 1*1G/120/6L/CB_bg_FR21
eMD520571G12Mi
EMEA
Middle East
LX.N110Y.038
eMD520-571G12Mi EM VHB32eTME2
UMA 1*1G/120/6L/CB_bg_AR11
Appendix A
142
Model
RO
Country
Acer Part No
Description
eMD520571G12Mi
EMEA
Switzerland
LX.N110Y.034
eMD520-571G12Mi VHB32eTCH1 UMA
1*1G/120/6L/CB_bg_IT41
eMD520571G12Mi
EMEA
UK
LX.N110Y.035
eMD520-571G12Mi VHB32eTGB1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
CHINA
China
LX.N110Y.056
eMD520-571G12Mi VHB32eTCN1 UMA
1*1G/120/6L/CB_bg_AN_SC11
eMD520571G12Mi
CHINA
Hong Kong
LX.N110Y.055
eMD520-571G12Mi VHB32eTHK2 UMA
1*1G/120/6L/CB_bg_AN_ZH31
eMD520571G12Ci
CHINA
China
LX.N110Y.054
eMD520-571G12Ci VHB32eTCN1 UMA
1*1G/120/6L/CB_bg_AN_SC11
eMD520571G12Ci
CHINA
Hong Kong
LX.N110Y.053
eMD520-571G12Ci VHB32eTHK2 UMA
1*1G/120/6L/CB_bg_AN_ZH31
eMD520571G12Ci
CHINA
China
LX.N110C.015
eMD520-571G12Ci LINPUSeCN1 UMA
1*1G/120/6L/CB_bg_AN_EN91
eMD520571G12Mi
CHINA
China
LX.N110C.014
eMD520-571G12Mi LINPUSeCN1 UMA
1*1G/120/6L/CB_bg_AN_EN91
eMD520571G12Mi
EMEA
South Africa
LX.N110Y.036
eMD520-571G12Mi EM VHB32eTZA1
UMA 1*1G/120/6L/CB_bg_FR21
eMD520571G12Mi
EMEA
South Africa
LX.N110Y.033
eMD520-571G12Mi EM VHB32eTZA2
UMA 1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
EMEA
Denmark
LX.N110Y.037
eMD520-571G12Mi VHB32eTDK1 UMA
1*1G/120/6L/CB_bg_NO11
eMD520571G12Mi
EMEA
France
LX.N110Y.032
eMD520-571G12Mi VHB32eTFR1 UMA
1*1G/120/6L/CB_bg_FR21
eMD520571G12Mi
EMEA
Germany
LX.N110Y.030
eMD520-571G12Mi VHB32eTDE1 UMA
1*1G/120/6L/CB_bg_DE11
eMD520571G12Mi
EMEA
Belgium
LX.N110Y.031
eMD520-571G12Mi VHB32eTBE1 UMA
1*1G/120/6L/CB_bg_NL11
eMD520571G12Mi
EMEA
Holland
LX.N110Y.029
eMD520-571G12Mi VHB32eTNL1 UMA
1*1G/120/6L/CB_bg_NL11
eMD520571G12Mi
EMEA
Luxembourg
LX.N110Y.028
eMD520-571G12Mi VHB32eTLU1 UMA
1*1G/120/6L/CB_bg_IT41
eMD520571G12Mi
EMEA
Norway
LX.N110Y.024
eMD520-571G12Mi VHB32eTNO1 UMA
1*1G/120/6L/CB_bg_NO11
eMD520571G12Mi
EMEA
Russia
LX.N110Y.025
eMD520-571G12Mi VHB32eTRU1 UMA
1*1G/120/6L/CB_bg_RU11
eMD520571G12Mi
EMEA
Sweden/Finland
LX.N110Y.026
eMD520-571G12Mi VHB32eTSE1 UMA
1*1G/120/6L/CB_bg_FI11
eMD520571G12Mi
EMEA
Czech
LX.N110Y.023
eMD520-571G12Mi VHB32eTCZ2 UMA
1*1G/120/6L/CB_bg_SK11
eMD520571G12Mi
EMEA
Eastern Europe
LX.N110Y.027
eMD520-571G12Mi VHB32eTEU4 UMA
1*1G/120/6L/CB_bg_FI11
eMD520571G12Mi
EMEA
Eastern Europe
LX.N110Y.022
eMD520-571G12Mi VHB32eTEU3 UMA
1*1G/120/6L/CB_bg_RU11
eMD520571G12Mi
EMEA
Eastern Europe
LX.N110Y.020
eMD520-571G12Mi VHB32eTEU7 UMA
1*1G/120/6L/CB_bg_ENG1
eMD520571G12Mi
EMEA
Eastern Europe
LX.N110Y.021
eMD520-571G12Mi VHB32eTEU1 UMA
1*1G/120/6L/CB_bg_CS21
eMD520571G12Mi
EMEA
Eastern Europe
LX.N110Y.019
eMD520-571G12Mi VHB32eTEU2 UMA
1*1G/120/6L/CB_bg_HU21
143
Appendix A
Model
RO
Country
eMD520571G12Mi
EMEA
Eastern Europe
LX.N110Y.018
eMD520-571G12Mi VHB32eTEU5 UMA
1*1G/120/6L/CB_bg_PL11
eMD520571G12Mi
PA
ACLA-Spanish
LX.N110Y.004
eMD520-571G12Mi EM VHB32eTEA1
UMA 1*1G/120/6L/CB_bg_ES21
eMD520571G12Mi
AAP
Australia/New
Zealand
LX.N110C.013
eMD520-571G12Mi LINPUSeAU1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Singapore
LX.N110C.012
eMD520-571G12Mi LINPUSeSG1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
India
LX.N110C.011
eMD520-571G12Mi LINPUSeIN1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Indonesia
LX.N110C.010
eMD520-571G12Mi LINPUSeID1 UMA
1*1G/120/6L/CB_bg_ID21
eMD520571G12Mi
AAP
Indonesia
LX.N110C.009
eMD520-571G12Mi LINPUSeID1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Philippines
LX.N110C.008
eMD520-571G12Mi LINPUSePH1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Malaysia
LX.N110C.007
eMD520-571G12Mi LINPUSeMY1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Thailand
LX.N110C.006
eMD520-571G12Mi LINPUSeTH1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Vietnam
LX.N110C.005
eMD520-571G12Mi LINPUSeVN1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Australia/New
Zealand
LX.N110Y.017
eMD520-571G12Mi VHB32eTAU1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
New Zealand
LX.N110Y.016
eMD520-571G12Mi VHB32eTNZ1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Singapore
LX.N110Y.015
eMD520-571G12Mi VHB32eTSG1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Singapore
LX.N110Y.014
eMD520-571G12Mi VHB32eTSG1 UMA
1*1G/120/6L/CB_bg_ZH31
eMD520571G12Mi
AAP
India
LX.N110Y.013
eMD520-571G12Mi VHB32eTIN1 UMA
1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Indonesia
LX.N110Y.012
eMD520-571G12Mi EM VHB32eTID1
UMA 1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Indonesia
LX.N110Y.011
eMD520-571G12Mi EM VHB32eTID1
UMA 1*1G/120/6L/CB_bg_ID21
eMD520571G12Mi
AAP
Philippines
LX.N110Y.010
eMD520-571G12Mi EM VHB32eTPH1
UMA 1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Malaysia
LX.N110Y.009
eMD520-571G12Mi EM VHB32eTMY1
UMA 1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
AAP
Thailand
LX.N110Y.008
eMD520-571G12Mi EM VHB32eTTH1
UMA 1*1G/120/6L/CB_bg_TH21
eMD520571G12Mi
AAP
Vietnam
LX.N110Y.007
eMD520-571G12Mi EM VHB32eTVN1
UMA 1*1G/120/6L/CB_bg_EN11
eMD520571G12Mi
PA
Canada
LX.N110Y.006
eMD520-571G12Mi VHB32eTCA2 UMA
1*1G/120/6L/CB_bg_FR31
eMD520571G12Mi
PA
USA
LX.N110Y.005
eMD520-571G12Mi VHB32eTUS1 UMA
1*1G/120/6L/CB_bg_EN31
eMD520571G12Mi
PA
ACLAPortuguese
LX.N110Y.003
eMD520-571G12Mi EM VHB32eTXC1
UMA 1*1G/120/6L/CB_bg_XC21
Appendix A
Acer Part No
Description
144
Model
RO
Country
Acer Part No
Description
eMD520571G12Mi
PA
ACLAPortuguese
LX.N110Y.002
eMD520-571G12Mi EM VHB32eTXC2
UMA 1*1G/120/6L/CB_bg_XC21
eMD520571G12Mi
PA
ACLA-Spanish
LX.N110Y.001
eMD520-571G12Mi EM VHB32eTEA3
UMA 1*1G/120/6L/CB_bg_ES21
eMD520570512Ci
AAP
Vietnam
LX.N110C.016
eMD520-570512Ci LINPUSeVN1 UMA
1*512/120/6L/CB_bg_AN_EN11
eMD520571G12Mi
WW
WW
S2.N110Y.001
eMD520-571G12Mi VHB32eWW1 UMA
2*512/120/6L/CB_bg_AN_EN13
eMD720321G12Mi
WW
WW
S2.N250Y.001
eMD720-321G12Mi VHB32eWW1 UMAC
2*512/120/6L/CB_bg_0.3D_AN_EN13
eMD720321G12C
CHINA
China
LX.N250Y.003
eMD720-321G12CVHB32eTCN1 UMAC
1*1G/120/6L/CB_0.3D_AN_SC11
eMD720321G16Mi
CHINA
China
LX.N250Y.002
eMD720-321G16Mi VHB32eTCN1
UMAC 1*1G/160/6L/
CB_bg_0.3D_AN_SC11
eMD720321G16Mi
TWN
GCTWN
LX.N250Y.001
eMD720-321G16Mi VHB32eTTW1
UMAC 1*1G/160/6L/
CB_bg_0.3D_AN_TC11
eMD720322G32Mi
PA
Canada
LX.N250Y.006
eMD720-322G32Mi VHB32eTCA2 UMAC
1*2G/320/6L/CB_bg_0.3D_AN_FR31
eMD720322G32Mi
PA
USA
LX.N250Y.005
eMD720-322G32Mi VHB32eTUS1 UMAC
1*2G/320/6L/CB_bg_0.3D_AN_EN31
eMD720322G32Mi
PA
ACLA-Spanish
LX.N250Y.004
eMD720-322G32Mi EM VHB32eTEA1
UMAC 1*2G/320/6L/
CB_bg_0.3D_AN_ES21
eMD520571G12Mi
CHINA
China
LX.N090Y.021
eMD520-571G12Mi VHB32eTCN1
UMAC 1*1G/120/6L/
CB_bg_0.3D_AN_SC11
eMD520571G12Mi
CHINA
Hong Kong
LX.N090Y.020
eMD520-571G12Mi VHB32eTHK2 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_ZH31
eMD520571G12Ci
CHINA
China
LX.N090Y.019
eMD520-571G12Ci VHB32eTCN1 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_SC11
eMD520571G12Ci
CHINA
Hong Kong
LX.N090Y.018
eMD520-571G12Ci VHB32eTHK2 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_ZH31
eMD520571G12Ci
CHINA
China
LX.N090C.015
eMD520-571G12Ci LINPUSeCN1 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_EN91
eMD520571G12Mi
CHINA
China
LX.N090C.014
eMD520-571G12Mi LINPUSeCN1 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_EN91
eMD520571G12Mi
AAP
Australia/New
Zealand
LX.N090C.010
eMD520-571G12Mi LINPUSeAU1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Singapore
LX.N090C.009
eMD520-571G12Mi LINPUSeSG1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
India
LX.N090C.011
eMD520-571G12Mi LINPUSeIN1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Indonesia
LX.N090C.008
eMD520-571G12Mi LINPUSeID1 UMAC
1*1G/120/6L/CB_bg_0.3D_ID21
eMD520571G12Mi
AAP
Indonesia
LX.N090C.012
eMD520-571G12Mi LINPUSeID1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Philippines
LX.N090C.007
eMD520-571G12Mi LINPUSePH1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
145
Appendix A
Model
RO
Country
Acer Part No
Description
eMD520571G12Mi
AAP
Malaysia
LX.N090C.013
eMD520-571G12Mi LINPUSeMY1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Thailand
LX.N090C.006
eMD520-571G12Mi LINPUSeTH1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Vietnam
LX.N090C.005
eMD520-571G12Mi LINPUSeVN1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Australia/New
Zealand
LX.N090Y.017
eMD520-571G12Mi VHB32eTAU1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
New Zealand
LX.N090Y.013
eMD520-571G12Mi VHB32eTNZ1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Singapore
LX.N090Y.012
eMD520-571G12Mi VHB32eTSG1
UMAC 1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Singapore
LX.N090Y.014
eMD520-571G12Mi VHB32eTSG1
UMAC 1*1G/120/6L/CB_bg_0.3D_ZH31
eMD520571G12Mi
AAP
India
LX.N090Y.011
eMD520-571G12Mi VHB32eTIN1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Indonesia
LX.N090Y.015
eMD520-571G12Mi EM VHB32eTID1
UMAC 1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Indonesia
LX.N090Y.010
eMD520-571G12Mi EM VHB32eTID1
UMAC 1*1G/120/6L/CB_bg_0.3D_ID21
eMD520571G12Mi
AAP
Philippines
LX.N090Y.016
eMD520-571G12Mi EM VHB32eTPH1
UMAC 1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Malaysia
LX.N090Y.009
eMD520-571G12Mi EM VHB32eTMY1
UMAC 1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
AAP
Thailand
LX.N090Y.008
eMD520-571G12Mi EM VHB32eTTH1
UMAC 1*1G/120/6L/CB_bg_0.3D_TH21
eMD520571G12Mi
AAP
Vietnam
LX.N090Y.007
eMD520-571G12Mi EM VHB32eTVN1
UMAC 1*1G/120/6L/CB_bg_0.3D_EN11
eMD520571G12Mi
PA
Canada
LX.N090C.004
eMD520-571G12Mi LINPUSeCA1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN31
eMD520571G12Mi
PA
USA
LX.N090C.003
eMD520-571G12Mi LINPUSeUS1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN31
eMD520571G12Mi
PA
ACLAPortuguese
LX.N090C.002
eMD520-571G12Mi LINPUSeXC1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN61
eMD520571G12Mi
PA
ACLA-Spanish
LX.N090C.001
eMD520-571G12Mi LINPUSeEA3 UMAC
1*1G/120/6L/CB_bg_0.3D_EN61
eMD520571G12Mi
PA
Canada
LX.N090Y.005
eMD520-571G12Mi VHB32eTCA2 UMAC
1*1G/120/6L/CB_bg_0.3D_FR31
eMD520571G12Mi
PA
USA
LX.N090Y.004
eMD520-571G12Mi VHB32eTUS1 UMAC
1*1G/120/6L/CB_bg_0.3D_EN31
eMD520571G12Mi
PA
ACLAPortuguese
LX.N090Y.006
eMD520-571G12Mi EM VHB32eTXC1
UMAC 1*1G/120/6L/CB_bg_0.3D_XC21
eMD520571G12Mi
PA
ACLAPortuguese
LX.N090Y.003
eMD520-571G12Mi EM VHB32eTXC2
UMAC 1*1G/120/6L/CB_bg_0.3D_XC21
eMD520571G12Mi
PA
ACLA-Spanish
LX.N090Y.002
eMD520-571G12Mi EM VHB32eTEA3
UMAC 1*1G/120/6L/CB_bg_0.3D_ES21
eMD520571G12Mi
PA
ACLA-Spanish
LX.N090Y.001
eMD520-571G12Mi EM VHB32eTEA1
UMAC 1*1G/120/6L/CB_bg_0.3D_ES21
eMD520171G12Mi
AAP
Thailand
LX.N090C.017
eMD520-171G12Mi LINPUSeTH1 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_EN11
Appendix A
146
Model
RO
Country
Acer Part No
Description
eMD520571G12Mi
PA
Canada
LX.N090Y.026
eMD520-571G12Mi VHB32eTCA2 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_FR31
eMD520571G12Mi
PA
USA
LX.N090Y.025
eMD520-571G12Mi VHB32eTUS1 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_EN31
eMD520571G12Mi
PA
ACLAPortuguese
LX.N090Y.024
eMD520-571G12Mi EM VHB32eTXC2
UMAC 1*1G/120/6L/
CB_bg_0.3D_AN_XC21
eMD520571G12Mi
PA
ACLA-Spanish
LX.N090Y.023
eMD520-571G12Mi EM VHB32eTEA3
UMAC 1*1G/120/6L/
CB_bg_0.3D_AN_ES21
eMD520571G12Mi
PA
ACLA-Spanish
LX.N090Y.022
eMD520-571G12Mi EM VHB32eTEA1
UMAC 1*1G/120/6L/
CB_bg_0.3D_AN_ES21
eMD520570512Mi
AAP
Indonesia
LX.N090C.019
eMD520-570512Mi LINPUSeID1 UMAC
1*512/120/6L/CB_bg_0.3D_AN_ID21
eMD520570512Ci
AAP
Vietnam
LX.N090C.016
eMD520-570512Ci LINPUSeVN1 UMAC
1*512/120/6L/CB_bg_0.3D_AN_EN11
eMD520572G12Mi
AAP
India
LX.N090C.026
eMD520-572G12Mi LINPUSeIN1 UMAC
2*1G/120/6L/CB_bg_0.3D_AN_EN11
eMD520581G12Mi
AAP
India
LX.N090C.025
eMD520-581G12Mi LINPUSeIN1 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_EN11
eMD520582G25Mi
AAP
India
LX.N090C.024
eMD520-582G25Mi LINPUSeIN1 UMAC
2*1G/250/6L/CB_bg_0.3D_AN_EN11
eMD520161G12Mi
AAP
India
LX.N090C.023
eMD520-161G12Mi LINPUSeIN1 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_EN11
eMD520162G25Mi
AAP
India
LX.N090C.022
eMD520-162G25Mi LINPUSeIN1 UMAC
2*1G/250/6L/CB_bg_0.3D_AN_EN11
eMD520172G25Mi
AAP
India
LX.N090C.021
eMD520-172G25Mi LINPUSeIN1 UMAC
2*1G/250/6L/CB_bg_0.3D_AN_EN11
eMD520171G12Mi
AAP
India
LX.N090C.020
eMD520-171G12Mi LINPUSeIN1 UMAC
1*1G/120/6L/CB_bg_0.3D_AN_EN11
eMD520570512Mi
AAP
Vietnam
LX.N090C.018
eMD520-570512Mi LINPUSeVN1 UMAC
1*512/120/6L/CB_bg_0.3D_AN_EN11
eMD720321G16M
CHINA
China
LX.N130C.001
eMD720-321G16MLINPUSeCN1 UMA
1*1G/160/6L/CB_AN_EN91
Model
CPU
LCD
Mem 1
Mem 2
HDD 1(GB)
ODD
WLAN
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
147
Appendix A
Model
CPU
LCD
Mem 1
Mem 2
HDD 1(GB)
ODD
WLAN
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Ci
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NCB24XS
3rd WiFi
BG
eMD520571G12Ci
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NCB24XS
3rd WiFi
BG
eMD520571G12Ci
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NCB24XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
Appendix A
148
Model
CPU
LCD
Mem 1
Mem 2
HDD 1(GB)
ODD
WLAN
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
149
Appendix A
Model
CPU
LCD
Mem 1
Mem 2
HDD 1(GB)
ODD
WLAN
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520570512Ci
CM575
N14.1WXGAG
SO512MBII6
N
N120GB
5.4KS
NCB24XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO512MBII6
SO512MBII6
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD720321G12Mi
PMDT
3200
N14.1WXGAG
SO512MBII6
SO512MBII6
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD720321G12C
PMDT
3200
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NCB24XS
N
eMD720321G16Mi
PMDT
3200
N14.1WXGAG
SO1GBII6
N
N160GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD720321G16Mi
PMDT
3200
N14.1WXGAG
SO1GBII6
N
N160GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD720322G32Mi
PMDT
3200
N14.1WXGAG
SO2GBII6
N
N320GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD720322G32Mi
PMDT
3200
N14.1WXGAG
SO2GBII6
N
N320GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD720322G32Mi
PMDT
3200
N14.1WXGAG
SO2GBII6
N
N320GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Ci
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NCB24XS
3rd WiFi
BG
eMD520571G12Ci
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NCB24XS
3rd WiFi
BG
eMD520571G12Ci
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NCB24XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
Appendix A
150
Model
CPU
LCD
Mem 1
Mem 2
HDD 1(GB)
ODD
WLAN
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
151
Appendix A
Model
CPU
LCD
Mem 1
Mem 2
HDD 1(GB)
ODD
WLAN
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520171G12Mi
CMT1700
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520571G12Mi
CM575
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520570512Mi
CM575
N14.1WXGAG
SO512MBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520570512Ci
CM575
N14.1WXGAG
SO512MBII6
N
N120GB
5.4KS
NCB24XS
3rd WiFi
BG
eMD520572G12Mi
CM575
N14.1WXGAG
SO1GBII6
SO1GBII6
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520581G12Mi
CM585
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520582G25Mi
CM585
N14.1WXGAG
SO1GBII6
SO1GBII6
N250GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520161G12Mi
CMT
1600
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520162G25Mi
CMT
1600
N14.1WXGAG
SO1GBII6
SO1GBII6
N250GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520172G25Mi
CMT
1700
N14.1WXGAG
SO1GBII6
SO1GBII6
N250GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520171G12Mi
CMT
1700
N14.1WXGAG
SO1GBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD520570512Mi
CM575
N14.1WXGAG
SO512MBII6
N
N120GB
5.4KS
NSM8XS
3rd WiFi
BG
eMD720321G16M
PMDT
3200
N14.1WXGAG
SO1GBII6
N
N160GB
5.4KS
NSM8XS
N
Appendix A
152
Appendix B
Test Compatible Components
This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® XP Home, Windows® XP Pro environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the eMachines D720/D520 Series
Compatibility Test Report released by the Acer Mobile System Testing Department.
Appendix B
153
Microsoft® Windows® Vista Environment Test
Vendor
Type
Description
Adapter Test
F0000183
DELTA CN
65W
Adapter DELTA 65W 1.7x5.5x11 SADP-65KB DFA LF
level 4
F0000183
DELTA CN
65W-DE
Adapter DELTA 65W 1.7x5.5x11 SADP-65KB BFJA LV4
LF for OBL only
10001023
LITE-ON
65W
Adapter LITE-ON 65W 1.7x5.5x11 PA-1650-02AC LF
level 4
60002015
HIPRO
65W
Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HPOK065B13 LED LF level 4
ALC268
ALC268
60001921
SANYO
6CELL2.2
Battery SANYO AS-2007A Li-Ion 3S2P SANYO 6 cell
4400mAh Main COMMON Normal Type
10001063
SONY
6CELL2.2
Battery SONY AS-2007A Li-Ion 3S2P SONY 6 cell
4400mAh Main COMMON Normal Type
60001535
PANASONI
C
6CELL2.2
Battery PANASONIC AS-2007A Li-Ion 3S2P
PANASONIC 6 cell 4400mAh Main COMMON PSS
60002162
SIMPLO
6CELL2.2
Battery SIMPLO AS-2007A Li-Ion 3S2P PANASONIC 6
cell 4400mAh Main COMMON PSS
60002162
SIMPLO
6CELL2.4
Battery SIMPLO AS-2007A Li-Ion 3S2P SAMSUNG 6
cell 2400mAh 2nd COMMON
60002162
SIMPLO
6CELL2.2
Battery SIMPLO AS-2007A Li-Ion 3S2P SAMSUNG 6
cell 4400mAh Main COMMON SDI 2.2mAh F type
Audio Codec
9999995
ONE TIME
VENDER
Battery Test
Bluetooth Test
9999995
ONE TIME
VENDER
BT 2.0
Foxconn Bluetooth FOX_BRM_2.0 F/W 300
9999995
ONE TIME
VENDER
0.3M DV
Bison 0.3M DV Lotus_2
9999995
ONE TIME
VENDER
0.3M DV
Suyin 0.3M DV Camellia_2
Camera Test
Card Reader Test
154
9999995
ONE TIME
VENDER
5 in 1-Build in
5 in 1-Build in MS, MS Pro, SD, SC, XD
9999995
ONE TIME
VENDER
JMB385
JMicron JMB385 Card Reader: SD/MMC/MS/MS Duo/
MS-HG (1/4/8-bit) & xD (PCI Express)
9999995
ONE TIME
VENDER
JMB385
JMicron JMB385 Card Reader: SD/MMC/MS/MS Duo/
MS-HG (1/4/8-bit) & xD (PCI Express)
Appendix B
Vendor
9999995
ONE TIME
VENDER
Type
Description
JMB385
JMicron JMB385 Card Reader: SD/MMC/MS/MS Duo/
MS-HG (1/4/8-bit) & xD (PCI Express)
10001067
INTEL
C2DP8400
CPU Intel Core2Dual P8400 PGA 2.26G 3M 1066 25W
10001067
INTEL
C2DP8600
CPU Intel Core2Dual P8600 PGA 2.4G 1066 25W 3M
10001067
INTEL
C2DT9400
CPU Intel Core2Dual T9400 PGA 2.53G 6M 1066 35W
10001067
INTEL
C2DP9500
CPU Intel Core2Dual P9500 PGA 2.53G 6M 1066 25W
10001067
INTEL
C2DT9600
CPU Intel Core2Dual T9600 PGA 2.8G 6M 1066 35W
10001067
INTEL
MVPQS
CPU Intel Core2Dual QS Montevina Penryn QS sample
10001067
INTEL
CM575
CPU Intel Celeron 575 PGA 2.0G 1M 667 MV
10001067
INTEL
CM585
CPU Intel Celeron 585 PGA 2.16G 1M 667 MV
10001067
INTEL
PMDT3400
CPU Intel Pentium Dual-Core T3400 PGA 2.16G 1M
667 MV
10001067
INTEL
CMT1600
CPU Intel CeleronM T1600 1.66G 1M 667 Dual Core,
MV
10001067
INTEL
CMT1700
CPU Intel CeleronM T1700 PGA 1.83G 1M 667 Dual
Core, MV
10001067
INTEL
PMDT3200
CPU Intel Pentium Dual-Core T3200 2.0G 1M 667 MV
10001067
INTEL
C2DP8600
CPU Intel Core2Dual P8600 PGA 2.4G 1066 25W 3M
10001067
INTEL
C2DP8600
CPU Intel Core2Dual P8600 PGA 2.4G 1066 25W 3M
10001067
INTEL
C2DT9400
CPU Intel Core2Dual T9400 PGA 2.53G 6M 1066 35W
10001067
INTEL
C2DT9400
CPU Intel Core2Dual T9400 PGA 2.53G 6M 1066 35W
10001067
INTEL
C2DP9500
CPU Intel Core2Dual P9500 PGA 2.53G 6M 1066 25W
10001067
INTEL
C2DP9500
CPU Intel Core2Dual P9500 PGA 2.53G 6M 1066 25W
10001067
INTEL
C2DT9600
CPU Intel Core2Dual T9600 PGA 2.8G 6M 1066 35W
10001067
INTEL
C2DT9600
CPU Intel Core2Dual T9600 PGA 2.8G 6M 1066 35W
10001067
INTEL
MVPQS
CPU Intel Core2Dual QS Montevina Penryn QS sample
10001067
INTEL
MVPQS
CPU Intel Core2Dual QS Montevina Penryn QS sample
CPU Test
Appendix B
155
Vendor
Type
Description
HDD Test
156
60002005
HGST SG
N120GB5.4KS
HDD HGST 2.5" 5400rpm 120GB HTS542512K9SA00
Bronco-B SATA II LF F/W:C31P
60002005
HGST SG
N120GB5.4KS
HDD HGST 2.5" 5400rpm 120GB HTS543212L9A300
Falcon-B SATA LF F/W:C40C
60001994
WD
N120GB5.4KS
HDD WD 2.5" 5400rpm 120GB WD1200BEVS-22UST0
ML125 SATA LF F/W:01.01A01
60002036
SEAGATE
N160GB5.4KS
HDD SEAGATE 2.5" 5400rpm 160GB ST9160827AS
Corsair SATA LF F/W:3.AAA
60002036
SEAGATE
N160GB5.4KS
HDD SEAGATE 2.5" 5400rpm 160GB ST9160310AS
Crockett SATA LF F/W:0303
60001922
TOSHIBA
DIGI
N160GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 160GB MK1646GSX Leo
BS SATA I LF F/W:LB113J
60002036
SEAGATE
N120GB5.4KS
HDD SEAGATE 2.5" 5400rpm 120GB ST9120817AS
Corsair SATA LF F/W:3.AAA
60001922
TOSHIBA
DIGI
N120GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 120GB MK1246GSX Leo
BS SATA I LF F/W:LB213J
60001922
TOSHIBA
DIGI
N120GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 120GB MK1252GSX
Virgo BS SATA LF F/W:LV010J
60001922
TOSHIBA
DIGI
N250GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 250GB MK2546GSX Leo
BS SATA I LF F/W:LB013J
60002005
HGST SG
N250GB5.4KS
HDD HGST 2.5" 5400rpm 250GB HTS542525K9SA00
Bronco-B SATA II LF F/W:C31P
60002005
HGST SG
N160GB5.4KS
HDD HGST 2.5" 5400rpm 160GB HTS542516K9SA00
Bronco-B SATA II LF F/W:C31P
60002005
HGST SG
N160GB5.4KS
HDD HGST 2.5" 5400rpm 160GB HTS543216L9A300
Falcon-B SATA LF F/W:C40C
60001994
WD
N160GB5.4KS
HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO
ML160 SATA LF F/W:11.01A11
60002036
SEAGATE
N250GB5.4KS
HDD SEAGATE 2.5" 5400rpm 250GB ST9250827AS
Corsair SATA LF F/W:3.AAA
60001994
WD
N250GB5.4KS
HDD WD 2.5" 5400rpm 250GB WD2500BEVS-22UST0
ML125 SATA LF F/W:01.01A01
60002036
SEAGATE
N320GB5.4KS
HDD SEAGATE 2.5" 5400rpm 320GB ST9320320AS
Crockett SATA LF F/W:0303
60002005
HGST SG
N320GB5.4KS
HDD HGST 2.5" 5400rpm 320GB HTS543232L9A300
Falcon-B SATA LF F/W:C40C
60001994
WD
N320GB5.4KS
HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0
ML160 SATA LF F/W:11.01A11
60001994
WD
N250GB5.4KS
HDD WD 2.5" 5400rpm 250GB WD2500BEVT-22ZCT0
ML160 SATA LF F/W:11.01A11
60001922
TOSHIBA
DIGI
N320GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 320GB MK3252GSX
Virgo BS SATA LF F/W:LV010J
60001922
TOSHIBA
DIGI
N160GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 160GB MK1652GSX
Virgo - BS SATA LF F/W:LV010J
Appendix B
Vendor
Type
Description
60001922
TOSHIBA
DIGI
N250GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 250GB MK2546GSX Leo
BS SATA I LF F/W:LB013J
60001922
TOSHIBA
DIGI
N250GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 250GB MK2546GSX Leo
BS SATA I LF F/W:LB013J
60002005
HGST SG
N250GB5.4KS
HDD HGST 2.5" 5400rpm 250GB HTS542525K9SA00
Bronco-B SATA II LF F/W:C31P
60001994
WD
N250GB5.4KS
HDD WD 2.5" 5400rpm 250GB WD2500BEVS-22UST0
ML125 SATA LF F/W:01.01A01
60001994
WD
N250GB5.4KS
HDD WD 2.5" 5400rpm 250GB WD2500BEVS-22UST0
ML125 SATA LF F/W:01.01A01
60002005
HGST SG
N250GB5.4KS
HDD HGST 2.5" 5400rpm 250GB HTS542525K9SA00
Bronco-B SATA II LF F/W:C31P
60001922
TOSHIBA
DIGI
N250GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 250GB MK2552GSX
Virgo BS SATA LF F/W:LV010J
60001994
WD
N120GB5.4KS
HDD WD 2.5" 5400rpm 120GB WD1200BEVT-22ZCT0
ML160 SATA LF F/W: 11.01A11
60002005
HGST SG
N250GB5.4KS
HDD HGST 2.5" 5400rpm 250GB HTS543225L9A300
Falcon-B SATA LF F/W:C40C
60001922
TOSHIBA
DIGI
N120GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 120GB MK1246GSX Leo
BS SATA I LF F/W:LB213J
60002005
HGST SG
N120GB5.4KS
HDD HGST 2.5" 5400rpm 120GB HTS542512K9SA00
Bronco-B SATA II LF F/W:C31P
60002005
HGST SG
N120GB5.4KS
HDD HGST 2.5" 5400rpm 120GB HTS542512K9SA00
Bronco-B SATA II LF F/W:C31P
60002036
SEAGATE
N160GB5.4KS
HDD SEAGATE 2.5" 5400rpm 160GB ST9160827AS
Corsair SATA LF F/W:3.AAA
60001922
TOSHIBA
DIGI
N120GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 120GB MK1246GSX Leo
BS SATA I LF F/W:LB213J
60001922
TOSHIBA
DIGI
N160GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 160GB MK1646GSX Leo
BS SATA I LF F/W:LB113J
60001922
TOSHIBA
DIGI
N160GB5.4KS
HDD TOSHIBA 2.5" 5400rpm 160GB MK1646GSX Leo
BS SATA I LF F/W:LB113J
60002005
HGST SG
N160GB5.4KS
HDD HGST 2.5" 5400rpm 160GB HTS542516K9SA00
Bronco-B SATA II LF F/W:C31P
60002005
HGST SG
N160GB5.4KS
HDD HGST 2.5" 5400rpm 160GB HTS542516K9SA00
Bronco-B SATA II LF F/W:C31P
60002036
SEAGATE
N160GB5.4KS
HDD SEAGATE 2.5" 5400rpm 160GB ST9160827AS
Corsair SATA LF F/W:3.AAA
RTL8111C
Realtek Lan RTL8111C
LAN Test
9999995
ONE TIME
VENDER
Appendix B
157
Vendor
Type
Description
LCD Test
60003316
AUO
N14.1WXGAG
LCD AUO 14.1" WXGA Glare B141EW04-V4 LF 200nit
16ms
60002215
SAMSUNG
N14.1WXGAG
LCD SAMSUNG 14.1" WXGA Glare LTN141W3-L01-J
L6 LF 200nit 16ms
60003089
LG
N14.1WXGAG
LCD LPL 14.1" WXGA Glare LP141WX3-TLN1 LF
200nit 16ms
10001038
CMO
N14.1WXGAG
LCD CMO 14.1" WXGA Glare N141I3-L02 LF 200nit
10ms
60002045
HYNIX
SO2GBII6
Memory HYNIX SO-DIMM DDRII 667 2GB
HYMP125S64CP8-Y5 LF
60001993
NANYA
SO512MBII6
Memory NANYA SO-DIMM DDRII 667 512MB
NT512T64UH8B0FN-3C LF 32*16 0.09um
60002215
SAMSUNG
SO512MBII6
Memory SAMSUNG SO-DIMM DDRII 667 512MB
M470T6464QZ3-CE6 LF
60002045
HYNIX
SO512MBII6
Memory HYNIX SO-DIMM DDRII 667 512MB
HYMP164S64CP6-Y5 LF 64*16 0.065um
60001993
NANYA
SO1GBII6
SO-DIMM DDRII 667 1GB NT1GT64U8HB0BN-3C
(0.09U)
60001993
NANYA
SO1GBII6
Memory NANYA SO-DIMM DDRII 667 1GB
NT1GT64UH8D0FN-3C LF 64*16 0.07um
60002215
SAMSUNG
SO1GBII6
Memory SAMSUNG SO-DIMM DDRII 667 1GB
M470T2864QZ3-CE6 LF
60002045
HYNIX
SO1GBII6
Memory HYNIX SO-DIMM DDRII 667 1GB
HYMP112S64CP6-Y5 LF
60001993
NANYA
SO2GBII6
Memory NANYA SO-DIMM DDRII 667 2GB
NT2GT64U8HD0BN-3C LF 128*8 0.07um
60002215
SAMSUNG
SO2GBII6
Memory SAMSUNG SO-DIMM DDRII 667 2GB
M470T5663QZ3-CE6 LF
23707801
FOXCONN
TW
Fox+LSI AM5 V2H 1.5_3.3V
Foxconn Delphi-AM5 V2H 1.5_3.3v T60M951
23707801
FOXCONN
TW
Fox+Con MC4Z 1.5_3.3V
Foxconn Conexant -Unizion 1.5_3.3v T60M955.02
23707801
FOXCONN
TW
Fox+LSI AM5 V2 3.3V Aus
Foxconn Delphi-AM5 V2 3.3v Aus T60M951.3x
Memory Test
Modem Test
Northbridge Chipset Test
10001067
INTEL
GL40
NB Chipset Intel CS GL40NB
60001922
TOSHIBA
DIGI
NCB24XS
ODD TOSHIBA COMBO 12.7mm Tray DL 24X TSL463A LF W/O bezel SATA
10001063
SONY
NCB24XS
ODD SONY COMBO 12.7mm Tray DL 24X CRX890S
LF W/O bezel SATA
ODD Test
158
Appendix B
Vendor
Type
Description
60001922
TOSHIBA
DIGI
NSM8XS
ODD TOSHIBA Super-Multi DRIVE 12.7mm Tray DL 8X
TS-L633A LF W/O bezel SATA
60001939
PIONEER
NSM8XS
ODD PIONEER Super-Multi DRIVE 12.7mm Tray DL 8X
DVR-TD08RS LF W/O bezel SATA
23418669
HLDS
NSM8XS
ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X
GSA-T50N LF W/O bezel SATA
23418669
HLDS
NSM8XS
ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X
GSA-T50N LF W/O bezel SATA Malaysia
10001063
SONY
NSM8XS
ODD SONY Super-Multi DRIVE 12.7mm Tray DL 8X
AD-7560S LF W/O bezel SATA
10001070
PHILIPS
NSM8XS
ODD PLDS Super-Multi DRIVE 12.7mm Tray DL 8X
DS-8A2S LF W/O bezel SATA
Southbridge Chipset Test
10001067
INTEL
ICH9M
SB Chipset Intel CS ICH9M
23707801
FOXCONN
TW
3rd WiFi BG
Foxconn FOX_ATH_XB63 Foxconn Atheros XB63
minicard b/g
9999995
ONE TIME
VENDER
3rd WiFi BG
Foxconn Wireless LAN Broadcom 4312 minicard b/g
9999995
ONE TIME
VENDER
3rd WiFi 1x2 BGN
Foxconn Wireless LAN Atheros AR5B91 1x2 BGN
9999995
ONE TIME
VENDER
3rd WiFi 1x2 BGN
Foxconn Wireless LAN Wireless LAN Ralink RT2700E
1x2 BGN
WLAN Test
Appendix B
159
160
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
•
Service guides for all models
•
User's manuals
•
Training materials
•
Bios updates
•
Software utilities
•
Spare parts lists
•
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
•
Detailed information on Acer's International Traveler's Warranty (ITW)
•
Returned material authorization procedures
•
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
161
162
Appendix C
Index
A
E
AFLASH Utility
Antennas
33
EasyTouch Failure
82
Euro
120
14
External Module Disassembly
B
Flowchart
Battery Pack
44
F
BIOS
password control
ROM size 16
ROM type 16
vendor 16
Version 16
Features 1
16
BIOS Supports protocol
33
FPC Cable 81
Flash Utility
FRU (Field Replaceable Unit) List
16
21–33
Advanced 24
Boot 31
Exit 32
Navigating 21
BIOS Utility
Onboard Device Configuration 27
Power 29
Save and Exit 32
Security 26
System Security 32
50
HDTV Switch Failure 120
Hard Disk Drive Module
Hibernation mode
13
Hot Keys 11
hotkey
I
Indicators 9
Intermittent Problems 122
Top View 129
114
Internal Speaker Failure 112
inverter board 78
brightness
Internal Microphone Failure
13
C
Camera Module
79
J
caps lock
Jumper and Connector Locations
5, 9
Common Problems 108
on indicator
computer
on indicator
CPU
133
H
Board Layout
hotkeys
43
129
Top View 129
K
5, 9
Keyboard
75
57
Keyboard Failure 111
D
L
DIMM Module 47
Display
3
77
81
LCD Failure 111
LCD Brackets
display
hotkeys
LCD Bezel
13
LCD Module Disassembly
Flowchart
76
163
80
lower cover 45
LCD Panel
Top
Touch Pad
hotkey
M
13
Touch Pad Failure 112
Main Unit Disassembly
Flowchart
Mainboard
TouchPad Bracket
54
Built-in KB Failure 111
EasyTouch Buttons 120
HDTV Switch 120
Internal Microphone 114
Internal Speakers 112
LCD Failure 111
Modem 119
No Display 109
ODD 116
Other Failures 121
Power On 108
Thermal Unit 120
Touch Pad 112
WLAN 119
5, 9
Memory Check 108
Model Definition 142
Modem Board 70
Modem Failure 119
on indicator
N
109
No Display Issue
Notebook Manager
hotkey
13
U
num lock
on indicator
65
Troubleshooting
71
media access
5, 9
Undetermined Problems
122
utility
O
BIOS
ODD Failure
116
Online Support Information 161
optical drive module
52
21–33
W
Windows 2000 Environment Test
Wireless Function Failure
P
WLAN Board
Panel
4
Bottom
left 4
PC Card
8
9
Power On Failure
108
S
Speaker Module
67
speakers
hotkey
13
System
Block Diagram
3
T
Test Compatible Components 153
Thermal Unit Failure
164
129
120
48
119
154
Download PDF

advertising