Page 1 of 57
Report No.: WST13080344-1ER
CE EMC Test Report
Electromagnetic Interference
Of
Product: Power adapter
Trade Name: energenie
Model Number:
EG-UC-AC1,EG-UC-AC1-B,EG-UC-AC2,EG-UC-AC2-B,
EG-UC-AC3,EG-UC-AC4
Prepared for
Shenzhen Gembird Electronics Ltd.
5th floor, Building B, Shifeng Industry Park, Huaning Road, Dalang Street, Longhua
District, Shenzhen
Prepared by
WST Certification & Testing (HK) Limited
12/F., San Toi Building,137-139 Connaught Road Central,Hong Kong
Hong Kong: TEL: +86-0852-2139 3077
FAX: +86-0852-2139 3217
Shenzhen office: TEL: +86-0755-2782 2785 FAX: +86-0755-2782 2175
E-mail:Michael@wstlab.com
Http:// www.wstlab.com
Page 3 of 57
Report No.: WST13080344-1ER
Table of Contents
Page
1 . TEST SUMMARY
6
1.1 TEST FACILITY
7
1.2 MEASUREMENT UNCERTAINTY
7
2 . GENERAL INFORMATION
8
2.1 GENERAL DESCRIPTION OF EUT
8
2.2 DESCRIPTION OF TEST MODES
9
2.3 DESCRIPTION OF TEST SETUP
10
2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL
11
2.5 MEASUREMENT INSTRUMENTS LIST
12
3 . EMC EMISSION TEST
14
3.1 CONDUCTED EMISSION MEASUREMENT
3.1.1 POWER LINE CONDUCTED EMISSION
3.1.2 TEST PROCEDURE
3.1.3 TEST SETUP
3.1.4 EUT OPERATING CONDITIONS
3.1.5 TEST RESULTS
14
14
15
15
15
16
3.2 RADIATED EMISSION MEASUREMENT
3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT
3.2.2 LIMITS OF RADIATED EMISSION MEASUREMENT
3.2.3 TEST PROCEDURE
3.2.4 TEST SETUP
3.2.5 EUT OPERATING CONDITIONS
3.2.6 TEST RESULTS
3.2.7 TEST RESULTS(1000~6000MHz)
18
18
18
18
19
19
20
22
3.3 HARMONICS CURRENT
3.3.1 LIMITS OF HARMONICS CURRENT
3.3.1.1 TEST PROCEDURE
3.3.1.2 EUT OPERATING CONDITIONS
3.3.1.3 TEST SETUP
3.3.2 TEST RESULTS
23
23
24
24
24
25
3.4 VOLTAGE FLUCTUATION AND FLICKERS
3.4.1 LIMITS OF VOLTAGE FLUCTUATION AND FLICKERS
3.4.1.1 TEST PROCEDURE
3.4.1.2 EUT OPERATING CONDITIONS
3.4.1.3 TEST SETUP
3.4.2 TEST RESULTS
30
30
30
30
30
31
Page 4 of 57
Report No.: WST13080344-1ER
Table of Contents
4 . EMC IMMUNITY TEST
Page
32
4.1 STANDARD COMPLIANCE/SERVRITY LEVEL/CRITERIA
32
4.2 GENERAL PERFORMANCE CRITERIA
33
4.3 GENERAL PERFORMANCE CRITERIA TEST SETUP
33
4.4 ESD TESTING
4.4.1 TEST SPECIFICATION
4.4.2 TEST PROCEDURE
4.4.3 TEST SETUP
4.4.4 TEST RESULTS
34
34
34
35
36
4.5 RS TESTING
4.5.1 TEST SPECIFICATION
4.5.2 TEST PROCEDURE
4.5.3 TEST SETU
4.5.4 TEST RESULTS
37
37
37
38
39
4.6 EFT/BURST TESTING
4.6.1 TEST SPECIFICATION
4.6.2 TEST PROCEDURE
4.6.3 TEST SETUP
4.6.4 TEST RESULTS
40
40
40
41
42
4.7 SURGE TESTING
4.7.1 TEST SPECIFICATION
4.7.2 TEST PROCEDURE
4.7.3 TEST SETUP
4.7.4 TEST RESULTS
43
43
43
44
45
4.8 INJECTION CURRENT TESTING
4.8.1 TEST SPECIFICATION
4.8.2 TEST PROCEDURE
4.8.3 TEST SETUP
4.8.4 TEST RESULTS
46
46
46
47
48
4.9 POWER FREQUENCY MAGNETIC FIELD TESTING
4.9.1 TEST SPECIFICATION
4.9.2 TEST PROCEDURE
4.9.3 TEST SETUP
4.9.4 TEST RESULTS
49
49
49
50
51
4.10 VOLTAGE INTERRUPTION/DIPS TESTING
4.10.1 TEST SPECIFICATION
4.10.2 TEST PROCEDURE
4.10.3 TEST SETUP
4.10.4 TEST RESULTS
52
52
52
52
53
Page 5 of 57
Table of Contents
Report No.: WST13080344-1ER
Page
5 . EUT TEST PHOTO
54
ATTACHMENT PHOTOGRAPHS OF EUT
55
Page 6 of 57
Report No.: WST13080344-1ER
1. TEST SUMMARY
Test procedures according to the technical standards:
EMC Emission
Standard
Test Item
Limit
Judgment
Conducted Emission
Class B
PASS
Radiated Emission
Class B
PASS
Class A
PASS
------
PASS
Remark
EN 55022:2010
EN61000-3-2:2006/A2:2009 Harmonic Current Emission
EN 61000-3-3:2008
Voltage Fluctuations &
Flicker
EMC Immunity
Section
EN 55024:2010
Test Item
Performance
Criteria
Judgment
EN 61000-4-2:2009
Electrostatic Discharge
B
PASS
EN 61000-4-3:2010
RF electromagnetic field
A
PASS
EN 61000-4-4:2012
Fast transients
B
PASS
EN 61000-4-5:2006
Surges
B
PASS
EN 61000-4-6:2012
Injected Current
A
PASS
A
PASS
B/C/C
PASS
EN 61000-4-8:2010
EN 61000-4-11:2004
Power Frequency
Magnetic Field
Volt. Interruptions Volt.
Dips
NOTE (3)
NOTE:
(1)” N/A” denotes test is not applicable in this Test Report
(2) The power consumption of EUT is less than 75W and no Limits apply.
(3) Voltage dip: 100% reduction – Performance Criteria B
Voltage dip: 30% reduction – Performance Criteria C
Voltage Interruption: 100% Interruption – Performance Criteria C
(4) For client’s request and manual description, the test will not be executed.
Remark
Page 7 of 57
Report No.: WST13080344-1ER
1.1 TEST FACILITY
WST Certification & Testing (HK) Limited
Address: 12/F., San Toi Building, 137-139 Connaught Road Central, Hong Kong
1.2 MEASUREMENT UNCERTAINTY
The reported uncertainty of measurement y ± U,where expended uncertainty U is based on a
standard uncertainty multiplied by a coverage factor of k=2,providing a level of confidence of
approximately 95 %。
A. Conducted Measurement :
Test Site
WSTC01
Method
ANSI
Measurement Frequency Range
150 KHz ~ 30MHz
U,(dB)
3.2
NOTE
U,(dB)
4.7
5.0
NOTE
B. Radiated Measurement :
Test Site
WSTA01
Method
ANSI
Measurement Frequency Range
30MHz ~ 1000MHz
1GHz ~6GHz
Report No.: WST13080344-1ER
Page 8 of 57
2. GENERAL INFORMATION
2.1 GENERAL DESCRIPTION OF EUT
Equipment
Power adapter
Model Name
EG-UC-AC1
EG-UC-AC1-B,EG-UC-AC2,EG-UC-AC2-B,EG-UC-AC3,
EG-UC-AC4
All the models are identical except output voltages and
output currents.
Serial No
Model Difference
The EUT is a Power adapter.
Product Description
Operating frequency:
Connecting I/O port:
N/A
N/A
Based on the application, features, or specification
exhibited in User's Manual, the EUT is considered as an
ITE/Computing Device. More details of EUT technical
specification, please refer to the User's Manual.
Power Source
AC Voltage
Power Rating
Input: AC110~240V, 50/60Hz, 0.3A;Output: 5V
, 1A×2
Report No.: WST13080344-1ER
Page 9 of 57
2.2 DESCRIPTION OF TEST MODES
To investigate the maximum EMI emission characteristics generates from EUT, the test
system was pre-scanning tested base on the consideration of following EUT operation
mode or test configuration mode which possible have effect on EMI emission level.
Each of these EUT operation mode(s) or test configuration mode(s) mentioned above
was evaluated respectively.
Pretest Mode
Mode 1
Description
Full Load
For Conducted Test
Final Test Mode
Description
Mode 1
Full Load
For Radiated Test
Final Test Mode
Mode 1
Description
Full Load
For EMS Test
Final Test Mode
Mode 1
Description
Full Load
Page 10 of 57
Report No.: WST13080344-1ER
2.3 DESCRIPTION OF TEST SETUP
Mode 1:
AC Line
E-1
EUT
C-1
E-2
Load
Page 11 of 57
Report No.: WST13080344-1ER
2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL
The EUT has been tested as an independent unit together with other necessary accessories or
support units. The following support units or accessories were used to form a representative test
configuration during the tests.
Item
Equipment
Mfr/Brand
Model/Type No.
Series No.
Note
E-1
Power adapter
energenie
EG-UC-AC1
N/A
EUT
E-2
Load
WEN SHUN
10ohm/9.5A
N/A
N/A
Item
Shielded Type
Ferrite Core
Length
C-1
NO
YES
120cm
Note
Note:
(1)
(2)
(3)
The support equipment was authorized by Declaration of Confirmation.
For detachable type I/O cable should be specified the length in cm in『Length』column.
“YES” is means “shielded” “with core”; “NO” is means “unshielded” “without core”.
Page 12 of 57
Report No.: WST13080344-1ER
2.5 MEASUREMENT INSTRUMENTS LIST
2.5.1 CONDUCTED TEST SITE
Item Kind of Equipment
Manufacturer
LISN
R&S
1
Type No.
ENV216
Serial No.
101313
Calibrated until
Jul. 06, 2014
2
LISN
EMCO
3816/2
00042990
Jul. 06, 2014
3
50Ω Switch
ANRITSU CORP
MP59B
6200983704
Jul. 06, 2014
4
Test Cable
N/A
C01
N/A
Jul. 06, 2014
5
Test Cable
N/A
C02
N/A
Jul. 06, 2014
6
Test Cable
N/A
C03
N/A
Jul. 06, 2014
7
EMI Test Receiver
Passive Voltage
Probe
Triple-Loop
Antenna
Absorbing Clamp
R&S
ESCI
101160
Jul. 06, 2014
ESH2-Z3
R&S
100196
Jul. 06, 2014
EVERFINE
LIA-2
11020003
Jul. 06, 2014
R&S
MDS-21
100423
Jul. 08, 2014
Type No.
CBL6111D
Serial No.
31216
Calibrated until
Jul. 06, 2014
8
9
10
2.5.2 RADIATED TEST SITE
Item Kind of Equipment
Manufacturer
Bilog Antenna
TESEQ
1
2
Test Cable
N/A
R-01
N/A
Jul. 06, 2014
3
Test Cable
N/A
R-02
N/A
Jul. 06, 2014
4
EMI Test Receiver
R&S
ESCI-7
101318
Jul. 06, 2014
5
Antenna Mast
EM
SC100_1
N/A
N/A
6
Turn Table
EM
SC100
060531
N/A
7
50Ω Switch
Anritsu Corp
MP59B
6200983705
Jul. 06, 2014
8
Spectrum Analyzer
Aglient
Jul. 06, 2014
9
Horn Antenna
EM
10
Amplifier
EM
E4407B
MY45108040
EM-AH-1018
2011071402
0
EM-30180
060538
2.5.3 HARMONICS AND FILCK
Item Kind of Equipment
Manufacturer
EM TEST
1 Harmonic & Flicker
2
AC Power Source
2.5.4 ESD
Item Kind of Equipment
ESD TEST
1
GENERATOR
Jul. 06, 2014
Jul. 06, 2014
Type No.
DPA500
Serial No.
0303-04
Calibrated until
Jul. 06, 2014
EM TEST
ACS500
0203-01
Jul. 06, 2014
Manufacturer
Type No.
EMS61000-2
A-V200
Serial No.
Calibrated until
11040001T
Jul. 06, 2014
EVERFINE
Page 13 of 57
Report No.: WST13080344-1ER
2.5.5 RS
Item Kind of Equipment
Signal Generator
1
Manufacturer
R&S
Type No.
SMT 06
Serial No.
832080/007
Calibrated until
Jul. 24, 2014
2
Log-Bicon Antenna
Schwarzbeck
VULB9161
4022
Aug. 15, 2014
3
Power Amplifier
Microwave Horn
Antenna
Power Amplifier
AR
150W1000M1
320946
Sep. 23, 2013
AR
AT4002A
321467
Jun. 11, 2014
AR
25S1G4A
308598
Sep. 23, 2013
Serial No.
Calibrated until
1101002
Jul. 06, 2014
1011002
Jul. 06, 2014
1012005
Aug. 04, 2014
Type No.
2023A
Serial No.
202301/368
Calibrated until
Mar. 31, 2014
4
5
2.5.6 SURGE, EFT/BURST, VOLTAGE INTERRUPTION/DIPS
Item Kind of Equipment
Manufacturer
Type No.
EMS61000-5
Surge Generator
EVERFINE
1
A
EMS61000-1
DIPS Generator
EVERFINE
2
1K
EMS61000-4
EFT/B Generator
EVERFINE
A-V2
2.5.7 INJECTION CURRENT
Item Kind of Equipment
Manufacturer
Signal Generator
IFR
1
2
Power Amplifier
AR
75A250AM1
0320709
Sep. 23, 2013
3
CDN
FCC
FCC-801-M2
06043
Jun. 02, 2014
4
EM Clamp
FCC
F-203I-23MM
504
Jun. 09, 2014
Manufacturer
Type No.
EMS61000-8
K
Serial No.
Calibrated until
1007001
Jul. 06, 2014
2.4.8 MF
Item Kind of Equipment
1
Generator
EVERFINE
Page 14 of 57
Report No.: WST13080344-1ER
3. EMC EMISSION TEST
3.1 CONDUCTED EMISSION MEASUREMENT
3.1.1 POWER LINE CONDUCTED EMISSION (Frequency Range 150KHz-30MHz)
FREQUENCY (MHz)
Class A (dBuV)
Class B (dBuV)
Quasi-peak
Average
Quasi-peak
Average
0.15 -0.5
79.00
66.00
66 - 56 *
56 - 46 *
0.50 -5.0
73.00
60.00
56.00
46.00
73.00
60.00
60.00
50.00
5.0 -30.0
Note:
(1) The tighter limit applies at the band edges.
(2) The limit of " * " marked band means the limitation decreases linearly with the
logarithm of the frequency in the range.
The following table is the setting of the receiver
Receiver Parameters
Attenuation
Start Frequency
Stop Frequency
IF Bandwidth
Setting
10 dB
0.15 MHz
30 MHz
9 kHz
Page 15 of 57
Report No.: WST13080344-1ER
3.1.2 TEST PROCEDURE
a. The EUT was placed 0.4 meters from the horizontal ground plane with EUT being connected
to the power mains through a line impedance stabilization network (LISN). All other support
equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling
impedance for the measuring instrument.
b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back
and forth in the center forming a bundle 30 to 40 cm long.
c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the
cable may be terminated, if required, using the correct terminating impedance. The overall
length shall not exceed 1 m.
d. LISN at least 80 cm from nearest part of EUT chassis.
e. For the actual test configuration, please refer to the related Item –EUT Test Photos.
3.1.3 TEST SETUP
3.1.4 EUT OPERATING CONDITIONS
The EUT tested system was configured as the statements of 2.3 Unless otherwise a special
operating condition is specified in the follows during the testing.
Page 16 of 57
Report No.: WST13080344-1ER
3.1.5 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode:
Test Voltage :
Power adapter
25 ℃
1010hPa
Full Load
AC 230V/60Hz
Model Name. :
EG-UC-AC1
Relative Humidity: 54%
Test Date :
2013-08-26
Phase :
L
Remark:
1. All readings are Quasi-Peak and Average values.
2. Factor = Insertion Loss + Cable Loss.
3. N/A means All Data have pass Limit
Page 17 of 57
EUT:
Temperature:
Pressure:
Test Mode:
Test Voltage :
Power adapter
25 ℃
1010hPa
Full Load
AC 230V/60Hz
Report No.: WST13080344-1ER
Model Name. :
EG-UC-AC1
Relative Humidity: 54%
Test Date :
2013-08-26
Phase :
N
Remark:
1. All readings are Quasi-Peak and Average values.
2. Factor = Insertion Loss + Cable Loss.
3. N/A means All Data have pass Limit
Page 18 of 57
Report No.: WST13080344-1ER
3.2 RADIATED EMISSION MEASUREMENT
3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT
(Below 1000MHz)
Class A
FREQUENCY (MHz)
30 – 230
Class B
At 10m
At 3m
At 10m
At 3m
dBuV/m
dBuV/m
dBuV/m
dBuV/m
40
50
30
40
230 – 1000
47
57
3.2.2 LIMITS OF RADIATED EMISSION MEASUREMENT
FREQUENCY (MHz)
1000-3000
Class A (at 3m) dBuV/m
37
(Above 1000MHz)
47
Class B (at 3m) dBuV/m
Peak
Avg
Peak
Avg
76
56
70
50
3000-6000
80
60
74
Notes:
(1) The limit for radiated test was performed according to as following:
CISPR 22.
(2) The tighter limit applies at the band edges.
(3) Emission level (dBuV/m)=20log Emission level (uV/m).
54
3.2.3 TEST PROCEDURE
a. The measuring distance of at 10 m shall be used for measurements at frequency up to 1GHz.
For frequencies above 1GHz, any suitable measuring distance may be used.
b. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 10 meter
open area test site. The table was rotated 360 degrees to determine the position of the highest
radiation.
c. The height of the equipment or of the substitution antenna shall be 0.8 m; the height of the test
antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the
antenna are set to make the measurement.
d. The initial step in collecting conducted emission data is a spectrum analyzer peak detector
mode pre-scanning the measurement frequency range. Significant peaks are then marked and
then Quasi Peak detector mode re-measured, above 1G Average detector mode will be
instead.
e. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the
EUT shall be deemed to meet QP(AV) Limits and then no additional QP Mode measurement
performed.
f. For the actual test configuration, please refer to the related Item –EUT Test Photos.
Page 19 of 57
Report No.: WST13080344-1ER
3.2.4 TEST SETUP
(A) Radiated Emission Test Set-Up Frequency Below 1 GHz
(B) Radiated Emission Test Set-Up Frequency Above 1GHz
3.2.5 EUT OPERATING CONDITIONS
The EUT tested system was configured as the statements of 2.3 Unless otherwise a special
operating condition is specified in the follows during the testing.
Page 20 of 57
Report No.: WST13080344-1ER
3.2.6 TEST RESULTS
EUT:
Power adapter
Model Name :
Temperature:
Pressure:
Test Mode :
Test Power :
26 ℃
1010 hPa
Full Load
AC 230V/60Hz
Relative Humidity: 54%
Test Date :
2013-08-26
Polarization :
Horizontal
Remark:
1. All readings are Quasi-Peak and Average values.
2. Factor = Antenna Factor + Cable Loss.
3. N/A means All Data have pass Limit
EG-UC-AC1
Page 21 of 57
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Power adapter
26 ℃
1010 hPa
Full Load
AC 230V/60Hz
Report No.: WST13080344-1ER
Model Name :
EG-UC-AC1
Relative Humidity: 54%
Test Date :
2013-08-26
Polarization :
Vertical
Remark:
1. All readings are Quasi-Peak and Average values.
2. Factor = Antenna Factor + Cable Loss.
3. N/A means All Data have pass Limit
Page 22 of 57
Report No.: WST13080344-1ER
3.2.7 TEST RESULTS(1000~6000MHz)
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Power adapter
26 ℃
1010 hPa
N/A
N/A
Model Name :
EG-UC-AC1
Relative Humidity: 54%
Test Date :
N/A
Page 23 of 57
3.3 HARMONICS CURRENT
3.3.1 LIMITS OF HARMONICS CURRENT
Report No.: WST13080344-1ER
Page 24 of 57
Report No.: WST13080344-1ER
3.3.1.1TEST PROCEDURE
a. The EUT was placed on the top of a wooden table 0.8 meters above the ground and operated
to produce the maximum harmonic components under normal operating conditions.
b. The classification of EUT is according to section 5 of EN 61000-3-2. The EUT is
classified as follows:
Class A: Balanced three-phase equipment, Household appliances excluding equipment as
Class D, Tools excluding portable tools, Dimmers for incandescent lamps, audio
equipment, equipment not specified in one of the three other classes.
Class B: Portable tools. Portable tools.; Arc welding equipment which is not professional
equipment.
Class C: Lighting equipment.
Class D: Equipment having a specified power less than or equal to600 W of the following
types: Personal computers and personal computer monitors and television
receivers.
c. The correspondent test program of test instrument to measure the current harmonics
emanated from EUT is chosen. The measure time shall be not less than the time necessary for
the EUT to be exercised.
3.3.1.2 EUT OPERATING CONDITIONS
The EUT tested system was configured as the statements of 2.3 Unless otherwise a special
operating condition is specified in the follows during the testing.
3.3.1.3 TEST SETUP
Page 25 of 57
Report No.: WST13080344-1ER
3.3.2 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Model Name :
EG-UC-AC1
Relative Humidity: 54%
Test Date :
2013-08-27
Power adapter
23 ℃
1010 hPa
Full Load
AC 230V/60Hz
E. U. T. Result
Harmonic(s) > 200%:
Order (n):
None
Harmonic(s) with average > 90%:
Order (n):
None
Harmonic(s) between 150% and 200% during more than 10% of the test time or max. 10min:
Order (n):
None
Power Source Result
First dataset out of limit:
DS (time):
None
Harmonic(s) out of limit:
Order (n):
None
Report No.: WST13080344-1ER
Page 26 of 57
Average harmonic current results
Hn
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Ieff [A]
275.777E-3
595.767E-6
63.043E-3
2.223E-3
13.628E-3
672.193E-6
10.375E-3
657.229E-6
2.018E-3
774.986E-6
2.137E-3
695.175E-6
2.129E-3
720.809E-6
918.806E-6
706.455E-6
903.224E-6
1.101E-3
1.568E-3
648.891E-6
844.229E-6
1.077E-3
772.046E-6
759.271E-6
941.900E-6
993.365E-6
847.818E-6
714.639E-6
889.189E-6
678.915E-6
1.464E-3
646.532E-6
934.446E-6
733.351E-6
1.246E-3
818.656E-6
1.423E-3
675.264E-6
1.768E-3
915.343E-6
Ieff [%]
99.575
0.215
22.763
0.803
4.921
0.243
3.746
0.237
0.729
0.280
0.772
0.251
0.769
0.260
0.332
0.255
0.326
0.398
0.566
0.234
0.305
0.389
0.279
0.274
0.340
0.359
0.306
0.258
0.321
0.245
0.529
0.233
0.337
0.265
0.450
0.296
0.514
0.244
0.638
0.331
Limit [%]
Result
2.00
26.09
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
10.00
7.00
5.00
3.00
3.00
3.00
3.00
3.00
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
Report No.: WST13080344-1ER
Page 27 of 57
Maximum harmonic current results
Hn
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Ieff [A]
276.955E-3
707.704E-6
63.567E-3
2.444E-3
13.852E-3
760.319E-6
10.512E-3
767.471E-6
2.186E-3
913.322E-6
2.242E-3
809.904E-6
2.311E-3
920.000E-6
1.156E-3
843.709E-6
1.185E-3
1.234E-3
1.782E-3
800.287E-6
951.107E-6
1.193E-3
1.011E-3
913.533E-6
1.356E-3
1.100E-3
1.075E-3
838.606E-6
1.007E-3
823.890E-6
1.577E-3
754.274E-6
1.170E-3
843.319E-6
1.460E-3
941.772E-6
2.062E-3
795.471E-6
1.925E-3
1.155E-3
Ieff [%]
100.000
0.256
22.952
0.882
5.002
0.275
3.796
0.277
0.789
0.330
0.809
0.292
0.834
0.332
0.418
0.305
0.428
0.446
0.643
0.289
0.343
0.431
0.365
0.330
0.490
0.397
0.388
0.303
0.364
0.297
0.569
0.272
0.422
0.304
0.527
0.340
0.745
0.287
0.695
0.417
Limit [%]
Result
3.00
39.13
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
15.00
10.50
7.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
4.50
Report No.: WST13080344-1ER
Page 28 of 57
Maximum harmonic voltage results
Hn
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Ueff [V]
231.52
76.71E-3
88.70E-3
23.80E-3
46.32E-3
15.04E-3
28.96E-3
13.85E-3
35.64E-3
11.64E-3
39.27E-3
11.31E-3
20.54E-3
12.70E-3
24.36E-3
13.63E-3
40.39E-3
12.70E-3
29.72E-3
12.86E-3
18.31E-3
15.24E-3
27.54E-3
14.72E-3
32.16E-3
13.64E-3
23.28E-3
16.79E-3
24.04E-3
13.32E-3
27.61E-3
13.93E-3
24.15E-3
11.95E-3
17.69E-3
14.06E-3
25.33E-3
10.96E-3
25.34E-3
12.79E-3
Ueff [%]
100.662
0.033
0.039
0.010
0.020
0.007
0.013
0.006
0.015
0.005
0.017
0.005
0.009
0.006
0.011
0.006
0.018
0.006
0.013
0.006
0.008
0.007
0.012
0.006
0.014
0.006
0.010
0.007
0.010
0.006
0.012
0.006
0.011
0.005
0.008
0.006
0.011
0.005
0.011
0.006
Limit [%]
0.2
0.9
0.2
0.4
0.2
0.3
0.2
0.2
0.2
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
Result
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
Report No.: WST13080344-1ER
Page 29 of 57
Harmonic current results - DS: 12
Hn
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Ieff [A]
276.801E-3
676.312E-6
63.163E-3
2.358E-3
13.850E-3
635.826E-6
10.299E-3
719.495E-6
1.915E-3
899.821E-6
2.151E-3
667.701E-6
1.856E-3
698.300E-6
856.266E-6
836.057E-6
911.515E-6
1.186E-3
1.400E-3
705.233E-6
789.838E-6
1.060E-3
736.493E-6
679.951E-6
917.607E-6
1.018E-3
791.235E-6
838.606E-6
752.249E-6
683.688E-6
1.462E-3
656.262E-6
1.046E-3
658.414E-6
1.177E-3
868.964E-6
1.413E-3
710.239E-6
1.579E-3
1.002E-3
Ieff [%]
99.944
0.244
22.806
0.852
5.001
0.230
3.719
0.260
0.691
0.325
0.777
0.241
0.670
0.252
0.309
0.302
0.329
0.428
0.505
0.255
0.285
0.383
0.266
0.246
0.331
0.368
0.286
0.303
0.272
0.247
0.528
0.237
0.378
0.238
0.425
0.314
0.510
0.256
0.570
0.362
Limit [%]
Result
2.00
26.09
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
10.00
7.00
5.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00
Page 30 of 57
Report No.: WST13080344-1ER
3.4 VOLTAGE FLUCTUATION AND FLICKERS
3.4.1 LIMITS OF VOLTAGE FLUCTUATION AND FLICKERS
3.4.1.1TEST PROCEDURE
a. Harmonic Current Test:
Test was performed according to the procedures specified in Clause 5.0 of IEC555-2 and/or
Sub-clause 6.2 of IEC/EN 61000-3-2 depend on which standard adopted for compliance
measurement.
b. Fluctuation and Flickers Test:
Tests was performed according to the Test Conditions/Assessment of Voltage Fluctuations
specified in Clause 5.0/6.0 of IEC555-3 and/or Clause 6.0/4.0 of IEC/EN 61000-3-3 depend on
which standard adopted for compliance measurement.
c. All types of harmonic current and/or voltage fluctuation in this report are assessed by direct
measurement using flicker-meter.
3.4.1.2 EUT OPERATING CONDITIONS
The EUT tested system was configured as the statements of 2.3 Unless otherwise a special
operating condition is specified in the follows during the testing.
3.4.1.3 TEST SETUP
Report No.: WST13080344-1ER
Page 31 of 57
3.4.2 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Model Name :
EG-UC-AC1
Relative Humidity: 54%
Test Date :
2013-08-27
Power adapter
22 ℃
1010 hPa
Full Load
AC 230V/60Hz
Maximum Flicker results
EUT values
Limit
Result
Pst
0.028
1.00
PASS
Plt
0.028
0.65
PASS
dc [%]
0.004
3.30
PASS
dmax [%]
0.215
7.00
PASS
dt [s]
0.000
0.50
PASS
Report No.: WST13080344-1ER
Page 32 of 57
4. EMC IMMUNITY TEST
4.1 STANDARD COMPLIANCE/SERVRITY LEVEL/CRITERIA
Tests
Standard No.
1. ESD
IEC/EN 61000-4-2
2. RS
IEC/EN 61000-4-3
3. EFT/Burst
IEC/EN 61000-4-4
4. Surges
IEC/EN 61000-4-5
5 Injected Current
IEC/EN 61000-4-6
6. Power Frequency
Magnetic Field
IEC/EN 61000-4-8
7. Volt. Interruptions
Volt. Dips
IEC/EN 61000-4-11
TEST SPECIFICATION
8KV air discharge
4KV contact discharge
4KV HCP discharge
4KV VCP discharge
80 MHz to 1000 MHz,
1000Hz, 80%,
AM modulated
5/50ns Tr/Th
5KHz Repetition Freq.
5/50ns Tr/Th
5KHz Repetition Freq.
Test Mode
Test Ports
Perform.
Criteria
Direct Mode
B
Indirect Mode
B
Enclosure
A
Power Supply
Port
CTL/Signal
Data Line
Port
B
B
1.2/50(8/20) Tr/Th us
L-N
B
1.2/50(8/20) Tr/Th us
L-PE
N-PE
B
CTL/Signal Port
A
AC Power Port
A
DC Power Port
A
Enclosure
A
0.15 MHz to 80 MHz,
1000Hz 80﹪,
AM Modulated
150Ω source impedance
0.15 MHz to 80 MHz,
1000Hz 80﹪,
AM Modulated
150Ω source impedance
0.15 MHz to 80 MHz,
1000Hz 80﹪,
AM Modulated
150Ω source impedance
50 Hz,
Voltage dip 100%
Voltage dip 30%
Interruption 100%
B
AC Power Port
C
C
Page 33 of 57
Report No.: WST13080344-1ER
4.2 GENERAL PERFORMANCE CRITERIA
According to EN 55024 standard, the general performance criteria as following:
The equipment shall continue to operate as intended without operator
intervention. No degradation of performance or loss of function is allowed below
a performance level specified by the manufacturer when the equipment is used
as intended.
Criterion A The performance level may be replaced by a permissible loss of
performance. If the minimum performance level or the permissible performance
loss is not specified by the manufacturer, then either of these may be derived
from the product description and documentation, and by what the user may
reasonably expect from the equipment if used as intended.
After the test, the equipment shall continue to operate as intended without
operator intervention. No degradation of performance or loss of function is
allowed, after the application of the phenomena below a performance level
specified by the manufacturer, when the equipment is used as intended.
Criterion B
The
performance level may be replaced by a permissible loss of performance.
During the test, degradation of performance is allowed. However, no change of
operating state or stored data is allowed to persist after the test.
Loss of function is allowed, provided the function is self-recoverable, or can be
restored by the operation of the controls by the user in accordance with the
Criterion C manufacturer’s instructions.
Functions, and/or information stored in non-volatile memory, or protected by a
battery backup, shall not be lost.
4.3 GENERAL PERFORMANCE CRITERIA TEST SETUP
The EUT tested system was configured as the statements of 2.3 Unless otherwise a special
operating condition is specified in the follows during the testing.
Page 34 of 57
Report No.: WST13080344-1ER
4.4 ESD TESTING
4.4.1 TEST SPECIFICATION
Basic Standard:
IEC/EN 61000-4-2
Discharge Impedance:
330 ohm / 150 pF
Required Performance
B
Discharge Voltage:
Air Discharge:2kV/4kV/8kV (Direct)
Contact Discharge:2kV/4kV (Direct/Indirect)
Polarity:
Positive & Negative
Number of Discharge:
Air Discharge: min. 20 times at each test point
Contact Discharge: min. 200 times in total
Discharge Mode:
Single Discharge
Discharge Period:
1 second minimum
4.4.2 TEST PROCEDURE
The test generator necessary to perform direct and indirect application of discharges to the EUT in
the following manner:
a. Contact discharge was applied to conductive surfaces and coupling planes of the EUT.
During the test, it was performed with single discharges. For the single discharge time
between successive single discharges was at least 1 second. The EUT shall be exposed to at
least 200 discharges, 100 each at negative and positive polarity, at a minimum of four test
points. One of the test points shall be subjected to at least 50 indirect discharges to the center
of the front edge of the horizontal coupling plane. The remaining three test points shall each
receive at least 50 direct contact discharges.
If no direct contact test points are available, then at least 200 indirect discharges shall be
applied in the indirect mode. Test shall be performed at a maximum repetition rate of one
discharge per second.
Vertical Coupling Plane (VCP):
The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and positioned at a
distance 0.1m from, the EUT, with the Discharge Electrode touching the coupling plane.
The four faces of the EUT will be performed with electrostatic discharge.
Horizontal Coupling Plane (HCP):
The coupling plane is placed under to the EUT. The generator shall be positioned vertically at
a distance of 0.1m from the EUT, with the Discharge Electrode touching the coupling plane.
The four faces of the EUT will be performed with electrostatic discharge.
b. Air discharges at insulation surfaces of the EUT.
It was at least ten single discharges with positive and negative at the same selected point.
Page 35 of 57
Report No.: WST13080344-1ER
4.4.3 TEST SETUP
Note:
TABLE-TOP EQUIPMENT
The configuration consisted of a wooden table 0.8 meters high standing on the Ground Reference
Plane. The GRP consisted of a sheet of aluminum at least 0.25mm thick, and 2.5 meters square
connected to the protective grounding system. A Horizontal Coupling Plane (1.6m x 0.8m) was
placed on the table and attached to the GRP by means of a cable with 940k total impedance. The
equipment under test, was installed in a representative system as described in section 7 of IEC
/EN 61000-4-2, and its cables were placed on the HCP and isolated by an insulating support of
0.5mm thickness. A distance of1-meter minimum was provided between the EUT and the walls of
the laboratory and any other metallic structure.
FLOOR-STANDING EQUIPMENT
The equipment under test was installed in a representative system as described in section 7 of
IEC/EN 61000-4-2, and its cables were isolated from the Ground Reference Plane by an
insulating support of0.1-meter thickness. The GRP consisted of a sheet of aluminum that is at
least 0.25mm thick, and 2.5meters square connected to the protective grounding system and
extended at least 0.5 meters from the EUT on all sides.
Report No.: WST13080344-1ER
Page 36 of 57
4.4.4 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Mode
Test level
(kV)
Test
Location
HCP
Model Name :
EG-UC-AC1
Relative Humidity: 45%
Test Date :
2013-08-27
Power adapter
24 ℃
1010 hPa
Full Load
AC 230V/60Hz
Air Discharge
4
+
8
-
+
Contact Discharge
10
-
VCP
+
15
-
+
2
-
4
6
+
Criterion
8
-
+
Result
+
-
+
-
-
A
A
A
A
PASS
A
A
A
A
PASS
A1
A
A
A
A
PASS
A2
A
A
A
A
PASS
A3
A
A
A
A
B
PASS
Note:
1) +/- denotes the Positive/Negative polarity of the output voltage.
2) Test condition:
Direct / Indirect (HCP/VCP) discharges: Minimum 50 times (Positive/Negative) at each
point. Air discharges: Minimum 10 times (Positive/Negative) at each point.
3) Test location(s) in which discharge (Air and contact discharge) to be applied illustrated
by photos shown in next page(s)
4) The Indirect (HCP/VCP) discharges description of test point as following:
1.left side 2.right side 3.front side 4.rear side
5) N/A - denotes test is not applicable in this test report
Page 37 of 57
Report No.: WST13080344-1ER
4.5 RS TESTING
4.5.1 TEST SPECIFICATION
Basic Standard:
IEC/EN 61000-4-3
Required Performance
A
Frequency Range:
80 MHz - 1000 MHz
Field Strength:
3 V/m
Modulation:
1kHz Sine Wave, 80%, AM Modulation
Frequency Step:
1 % of fundamental
Polarity of Antenna:
Horizontal and Vertical
Test Distance:
3m
Antenna Height:
1.5 m
Dwell Time:
at least 3 seconds
4.5.2 TEST PROCEDURE
The EUT and support equipment, which are placed on a table that is 0.8 meter above ground and
the testing was performed in a fully-anechoic chamber.
The testing distance from antenna to the EUT was 3 meters.
The other condition as following manner:
a. The frequency range is swept from 80 MHz to 1000 MHz, & 1400MHz - 2700MHz with the
signal 80%amplitude modulated with a 1kHz sine wave. The rate of sweep did not exceed 1.5x
10-3 decade/s. Where the frequency range is swept incrementally, the step size was 1% of
fundamental.
b. Sweep Frequency 900 MHz, with the Duty Cycle:1/8 and Modulation: Pulse 217 Hz(if
applicable)
c. The dwell time at each frequency shall be not less than the time necessary for the
EUT to be able to respond.
d. The test was performed with the EUT exposed to both vertically and horizontally
polarized fields on each of the four sides.
Page 38 of 57
Report No.: WST13080344-1ER
4.5.3 TEST SETU
Note:
TABLE-TOP EQUIPMENT
The EUT installed in a representative system as described in section 7 of IEC/EN 61000-4-3 was
placed on a non-conductive table 0.8 meters in height. The system under test was connected to
the power and signal wire according to relevant installation instructions.
FLOOR-STANDING EQUIPMENT
The EUT installed in a representative system as described in section 7 of IEC/EN 61000-4-3 was
placed on a non-conductive wood support 0.1 meters in height. The system under test was
connected to the power and signal wire according to relevant installation instructions.
Report No.: WST13080344-1ER
Page 39 of 57
4.5.4 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Model Name :
EG-UC-AC1
Relative Humidity: 60%
Test Date :
2013-08-26
Power adapter
25 ℃
1010 hPa
Full Load
AC 230V/60Hz
Frequency Range
RF Field
R.F.
(MHz)
Position
Field Strength
Azimuth
Perform.
Criteria
Results Judgment
Front
3 V/m (rms)
80MHz - 1000MHz
H/V
Rear
AM Modulated
1000Hz, 80%
A
A
PASS
Left
Right
Note:
1) N/A - denotes test is not applicable in this test report.
2) Criteria A: There was no change operated with initial operating during the test.
3) Criteria B: The EUT function loss during the test, but self-recoverable after the test.
4) Criteria C: The system shut down during the test.
Page 40 of 57
Report No.: WST13080344-1ER
4.6 EFT/BURST TESTING
4.6.1 TEST SPECIFICATION
Basic Standard:
IEC/EN 61000-4-4
Required Performance
B
Test Voltage:
Power Line:1 kV
Signal/Control Line:0.5 KV
Polarity:
Positive & Negative
Impulse Frequency:
5 kHz
Impulse Wave shape :
5/50 ns
Burst Duration:
15 ms
Burst Period:
300 ms
Test Duration:
Not less than 1 min.
4.6.2 TEST PROCEDURE
The EUT and support equipment, are placed on a table that is 0.8 meter above a metal ground
plane measured 1m*1m min. and 0.65mm thick min.
The other condition as following manner:
a. The length of power cord between the coupling device and the EUT should not exceed 1
meter.
b. Both positive and negative polarity discharges were applied.
c. The duration time of each test sequential was 1 minute
Page 41 of 57
Report No.: WST13080344-1ER
4.6.3 TEST SETUP
Note:
TABLE-TOP EQUIPMENT
The configuration consisted of a wooden table (0.8m high) standing on the Ground Reference
Plane. The GRP consisted of a sheet of aluminum (at least 0.25mm thick and 2.5m square)
connected to the protective grounding system. A minimum distance of 0.5m was provided
between the EUT and the walls of the laboratory or any other metallic structure.
FLOOR-STANDING EQUIPMENT
The EUT installed in a representative system as described in section 7 of IEC/EN 61000-4-4 and
its cables, were isolated from the Ground Reference Plane by an insulating support that is
0.1-meter thick. The GRP consisted of a sheet of aluminum (at least 0.25mm thick and 2.5m
square) connected to the protective grounding system.
Report No.: WST13080344-1ER
Page 42 of 57
4.6.4 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Model Name :
EG-UC-AC1
Relative Humidity: 60%
Test Date :
2013-08-27
Power adapter
22 ℃
1010 hPa
Full Load
AC 230V/60Hz
Test level (kV)
Coupling Line
AC
line
0.5
1
2
+
Criterion
4
-
+
Result
+
-
+
-
-
L
A
A
A
A
PASS
N
A
A
A
A
PASS
PE
L+N
L+PE
B
N+PE
L+N+PE
DC Line
Signal Line
Note:
1) +/- denotes the Positive/Negative polarity of the output voltage.
2) N/A - denotes test is not applicable in this test report
3) Criteria A: There was no change operated with initial operating during the test.
4) Criteria B: The EUT function loss during the test, but self-recoverable after the test.
5) Criteria C: The system shut down during the test.
Page 43 of 57
Report No.: WST13080344-1ER
4.7 SURGE TESTING
4.7.1 TEST SPECIFICATION
Basic Standard:
IEC/EN 61000-4-5
Required Performance
B
Wave-Shape:
Combination Wave
1.2/50 us Open Circuit Voltage
8 /20 us Short Circuit Current
Test Voltage:
Power Line:0.5 kV, 1 kV, 2 kV
Surge Input/Output:
L-N, L-PE, N-PE
Generator Source:
2 ohm between networks
Impedance:
12 ohm between network and ground
Polarity:
Positive/Negative
Phase Angle:
0 /90/180/270°
Pulse Repetition Rate:
1 time / min. (maximum)
Number of Tests:
5 positive and 5 negative at selected points
4.7.2 TEST PROCEDURE
a. For EUT power supply:
The surge is to be applied to the EUT power supply terminals via the capacitive coupling
network. Decoupling networks are required in order to avoid possible adverse effects on
equipment not under test that may be powered by the same lines, and to provide sufficient
decoupling impedance to the surge wave. The power cord between the EUT and the
coupling/decoupling networks shall be 2meters in length (or shorter).
b. For test applied to unshielded unsymmetrically operated interconnection lines of EUT:
The surge is applied to the lines via the capacitive coupling. The coupling /decoupling
networks shall not influence the specified functional conditions of the EUT. The
interconnection line between the EUT and the coupling/decoupling networks shall be 2 meters
in length (or shorter).
c. For test applied to unshielded symmetrically operated interconnection /telecommunication
lines of EUT:
d. The surge is applied to the lines via gas arrestors coupling. Test levels below the ignition point
of the coupling arrestor cannot be specified. The interconnection line between the EUT and
the coupling/decoupling networks shall be 2 meters in length (or shorter).
Page 44 of 57
4.7.3 TEST SETUP
Report No.: WST13080344-1ER
Report No.: WST13080344-1ER
Page 45 of 57
4.7.4 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Model Name :
EG-UC-AC1
Relative Humidity: 60%
Test Date :
2013-08-27
Power adapter
21 ℃
1010 hPa
Full Load
AC 230V/60Hz
Test level
Coupling Line
L-N
0.5 kV
+
-
1 kV
2 kV
+
-
0°
A
A
B
B
90°
A
A
B
B
180°
A
A
B
B
270°
A
A
B
B
+
Criterion
4 kV
-
+
Result
-
PASS
0°
AC
line
L-PE
90°
B
180°
270°
0°
N-PE
90°
180°
270°
DC Line
Signal Line
Note:
1) Polarity and Numbers of Impulses:5 Pst / Ngt at each tested mode
2) N/A - denotes test is not applicable in this Test Report
3) Criteria A: There was no change operated with initial operating during the test.
4) Criteria B: The EUT function loss during the test, but self-recoverable after the test.
5) Criteria C: The system shut down during the test.
Page 46 of 57
Report No.: WST13080344-1ER
4.8 INJECTION CURRENT TESTING
4.8.1 TEST SPECIFICATION
Basic Standard:
IEC/EN 61000-4-6
Required Performance
A
Frequency Range:
0.15 MHz - 80 MHz
Field Strength:
3 Vr.m.s.
Modulation:
1kHz Sine Wave, 80%, AM Modulation
Frequency Step:
1 % of fundamental
Dwell Time:
at least 3 seconds
4.8.2 TEST PROCEDURE
The EUT and support equipment, are placed on a table that is 0.8 meter above a metal ground
plane measured 1m*1m min. and 0.65mm thick min.
The other condition as following manner:
a. The frequency range is swept from 150 KHz to 80 MHz, with the signal 80%amplitude
modulated with a 1kHz sine wave. The rate of sweep did not exceed 1.5x 10-3 decade/s.
Where the frequency range is swept incrementally, the step size was 1% of fundamental.
b. The dwell time at each frequency shall be not less than the time necessary for the
EUT to be able to respond.
Page 47 of 57
Report No.: WST13080344-1ER
4.8.3 TEST SETUP
NOTE:
FLOOR-STANDING EQUIPMENT
The equipment to be tested is placed on an insulating support of 0.1 meters height above a
ground reference plane. All relevant cables shall be provided with the appropriate coupling and
decoupling devices at a distance between 0.1 meters and 0.3 meters from the projected geometry
of the EUT on the ground reference plane.
Report No.: WST13080344-1ER
Page 48 of 57
4.8.4 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Test Ports
(Mode)
Input/ Output
AC. Power Port
Input/ Output
DC. Power Port
Model Name :
EG-UC-AC1
Relative Humidity: 60%
Test Date :
2013-08-27
Power adapter
20 ℃
1010 hPa
Full Load
AC 230V/60Hz
Freq. Range
MHz)
Field Strength
0.15 ---80
Perform.
Results
Judgment
A
A
PASS
A
N/A
N/A
A
N/A
N/A
Criteria
3V(rms)
0.15 --- 80
AM Modulated
1000Hz, 80%
Signal Line
0.15 --- 80
Note:
1) N/A - denotes test is not applicable in this Test Report.
2) Criteria A: There was no change operated with initial operating during the test.
3) Criteria B: The EUT function loss during the test, but self-recoverable after the test.
4) Criteria C: The system shut down during the test.
Page 49 of 57
Report No.: WST13080344-1ER
4.9 POWER FREQUENCY MAGNETIC FIELD TESTING
4.9.1 TEST SPECIFICATION
Basic Standard:
IEC/EN 61000-4-8
Required Performance
A
Frequency Range:
50Hz
Field Strength:
1 A/m
Observation Time:
1 minute
Inductance Coil:
Rectangular type, 1mx1m
4.9.2 TEST PROCEDURE
The EUT and support equipment, are placed on a table that is 0.8 meter above a metal ground
plane measured 1m*1m min. and 0.65mm thick min.
The other condition as following manner:
a. The equipment cabinets shall be connected to the safety earth directly on the GRP via the
earth terminal of the EUT.
b. The cables supplied or recommended by the equipment manufacturer shall be used. 1 meter
of all cables used shall be exposed to the magnetic field.
Page 50 of 57
Report No.: WST13080344-1ER
4.9.3 TEST SETUP
Note:
TABLE-TOP EQUIPMENT
The equipment shall be subjected to the test magnetic field by using the induction coil of standard
dimension (1 m x 1 m). The induction coil shall then be rotated by 90 degrees in order to expose
the EUT to the test field with different orientations.
FLOOR-STANDING EQUIPMENT
The equipment shall be subjected to the test magnetic field by using induction coils of suitable
dimensions. The test shall be repeated by moving and shifting the induction coils, in order to test
the whole volume of the EUT for each orthogonal direction. The test shall be repeated with the coil
shifted to different positions along the side of the EUT, in steps corresponding to 50 % of the
shortest side of the coil. The induction coil shall then be rotated by 90 degrees in order to expose
the EUT to the test field with different orientations.
Page 51 of 57
Report No.: WST13080344-1ER
4.9.4 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Model Name :
EG-UC-AC1
Relative Humidity: 60%
Test Date :
2013-08-27
Power adapter
23 ℃
1010 hPa
Full Load
AC 230V/60Hz
Duration
Perform
(s)
Criteria
X
60 s
A
A
Pass
1 A/m
Y
60 s
A
A
Pass
1 A/m
Z
60 s
A
A
Pass
Test Mode
Test Level
Antenna
aspect
Enclosure
1 A/m
Enclosure
Enclosure
Results
Judgment
Note:
1) N/A - denotes test is not applicable in this test report
2) Criteria A: There was no change operated with initial operating during the test.
3) Criteria B: The EUT function loss during the test, but self-recoverable after the test.
4) Criteria C: The system shut down during the test.
Page 52 of 57
Report No.: WST13080344-1ER
4.10 VOLTAGE INTERRUPTION/DIPS TESTING
4.10.1 TEST SPECIFICATION
Basic Standard:
IEC/EN 61000-4-11
Required Performance
B (For 100% Voltage Dips)
C (For 30% Voltage Dips)
C (For 100% Voltage Interruptions)
Test Duration Time:
Minimum three test events in sequence
Interval between Event:
Minimum ten seconds
Phase Angle:
0°/45°/90°/135°/180°/225°/270°/315°/360°
Test Cycle:
3 times
4.10.2 TEST PROCEDURE
The EUT shall be tested for each selected combination of test levels and duration with a
sequence of three dips/interruptions with intervals of 10 s minimum (between each test event).
Each representative mode of operation shall be tested. Abrupt changes in supply voltage shall
occur at zero crossings of the voltage waveform.
4.10.3 TEST SETUP
Page 53 of 57
Report No.: WST13080344-1ER
4.10.4 TEST RESULTS
EUT:
Temperature:
Pressure:
Test Mode :
Test Power :
Power adapter
22 ℃
1010 hPa
Full Load
AC 230V/60Hz
Model Name :
EG-UC-AC1
Relative Humidity: 60%
Test Date :
2013-08-26
Duration
Perform
(T)
Criteria
Voltage dip 100%
0.5
Voltage dip 30%
Voltage dip 100%
Interruption & Dips
Results
Judgment
B
B
PASS
25
C
B
PASS
250
C
C
PASS
Note:
1). N/A - denotes test is not applicable in this test report.
2) Criteria A: There was no change operated with initial operating during the test.
3) Criteria B: The EUT function loss during the test, but self-recoverable after the test.
4) Criteria C: The system shut down during the test.
Page 54 of 57
5. EUT TEST PHOTO
Radiated Measurement Photos
Report No.: WST13080344-1ER
Page 55 of 57
Report No.: WST13080344-1ER
ATTACHMENT PHOTOGRAPHS OF EUT
Photo 1
Photo 2
Page 56 of 57
Photo 3
Photo 4
Report No.: WST13080344-1ER
Page 57 of 57
Photo 5
Report No.: WST13080344-1ER