Ball Electronic Display Division | TD Series | Pipe &Conduit

3M Electrical Markets Division
Locate
Plastic
Pipe &
Conduit
3M™ Electronic Marking System (EMS) Caution Tape 7600 Series
3M™ Dynatel™ Cable/Pipe/Fault/EMS Tape Locators 7000 Series
3M™ EMS (Electronic Marking System) Caution Tape 7600 Series
3M™ Dynatel™ Cable/Pipe/Fault/EMS Tape Locators 7000 Series
Introducing 3M’s Next Generation of Underground Infrastructure Asset Management
A Revolutionary Approach to Locating Plastic
Pipes/Conduit Path
System Benefits
3M has over 30 years experience developing new and innovative solutions for
• Eliminates need to install
tracer wire
markers and programmable ID markers and continues to set the standard for
• No access points or connections
required
locating buried assets. 3M pioneered electronic marker technology with EMS
innovation with its newest path marking technology.
Now, 3M has developed an effective way to locate the path of underground
• Locate without the need of a
transmitter
with tracer wire and test stations.
• Unique identification for each
utility type
plastic pipes and conduits, eliminating the need, problems and costs associated
• Low installed costs
• Tape does not provide a path
for lightning
• Signal path maintained even if
the tape is cut or damaged
• Product design life — 50 years
EMS Caution Tape for Path Marking
3M™ Electronic Marking System Caution Tape uses a new EMS marker technology
embedded into a caution tape for installation near or above the buried facility and
helps provide continuous path location. When energized using a 3M™ Dynatel™
Locator 7000 Series, the markers are activated. The markers require no batteries,
and there is no need to hook up an external transmitter or search for access points.
The markers work independently, so even if a section of caution tape is cut or
removed, the other markers on the tape would continue to provide accurate location.
3M™ Electronic Marking System (EMS)
Caution Tape 7600 Series
Each version of 3M™ EMS Caution Tape is tuned to a frequency specific to the
path of that utility (gas, telco, or wastewater) and can be buried up to two feet (.76 m).
EMS Electronic Markers for Point Marking
3M™ EMS Caution Tape for path marking is a perfect complement to 3M’s existing
line of EMS passive and ID markers (Near Surface, Ball and Full Range markers)
which are used for marking points of interest, such as splices, service drops,
valves, etc.
ID markers can be programmed to include specific information such as facility data,
type of application, placement date and other important details.
3M™ Electronic Marker Specifications
Color
Telephone
Power
CATV
General
Purpose
Water
Wastewater
Gas
Read
Range*
orange
red
black/orange
purple
blue
green
yellow
n/a
ID Ball Marker
1421-XR/ID 1422-XR/ID 1427-XR/ID 1428-XR/ID 1423-XR/ID 1424-XR/ID 1425-XR/ID 5 ft. (1.5 m)
ID Near-Surface
1432-XR/ID 1433-XR/ID 1437-XR/ID 1438-XR/ID 1434-XR/ID 1435-XR/ID 1436-XR/ID 3 ft. (0.9 m)
ID Full-Range
1250-XR/ID 1251-XR/ID
Non-ID
Ball Marker XR
N/A
1248-XR/ID 1252-XR/ID 1253-XR/ID 1254-XR/ID 8 ft. (2.4 m)
1401-XR
1402-XR
1407-XR
1408-XR
1403-XR
1404-XR
1405-XR 6 ft. (1.8 m)
Near-Surface Marker
1432
1433
N/A
N/A
1434
1435
1436
3 ft. (0.9 m)
Mini-Marker
1255
1256
N/A
N/A
1257
1258
1259
7 ft. (2.1 m)
Full-Range
1250
1251
N/A
N/A
1252
1253
1254
9 ft. (2.7 m)
*Read range specifies maximum distance from locator probe using 3M™ Dynatel™ Locator 7000 Series.
Read range may vary on export models–refer to product bulletins. Some countries do not allow all marker
operating frequencies.
3M™ ID Ball Markers
3M™ EMS Caution Tape 7600 Series Specifications
Description:
6 Mil PE film with 3M Markers for locating
Part Number:
7600 Series
Tape Material:
Polyethylene
Color(s):
Yellow, Orange, Green
Gauge(s):
6 Mil (+/- 10%)
Roll Width(s):
6" (0.15 m)
Roll Length:
1,312 ft. (400 m)
Density*:
.920 g/cc (6.0 Mil)
Tensile at Break (psi) /
(with markers attached)*:
MD 1307 (+/- 5%)
TD 377 (+/- 5%)
Elongation (%)*:
MD 7.8
3M™ Electronic Marking System (EMS) Caution
Tape 7600 Series
TD 12.7
Tear Strength (g)*:
MD 440
TD 1200
Physical Specifications:
Weight(s):
22 lbs. @ 4" wide
44 lbs. @ 6" wide
Spool size: 6" wide
19.5 in. (.5 m) dia. x 12 in. (.3 m)
Spool hole:
3.0 dia in
Environmental Specifications:
Operating temperature
-4° F to 122° F (-20° C to 50° C)
Storage temperature
-4° F to 149° F (-20° C to 65° C)
Compatibility:
3M™ Dynatel™ 7400 and 7500 Series Locators
Maximum Burial Depth**:
7600 Series Tape
2.0 ft. (.61 m) (maximum)**
* Based on average production
** Using 3M™ Dynatel™ 7000 Series Locators
Ordering Information
Product Number
Product Description
3M ID
7605-XR-CT-GAS
EMS Tape 6", 400 m roll, English
80-6116-1196-5
7604-XR-CT-WW
EMS Tape 6", 400 m roll, English
80-6116-1198-1
7601-XR-CT-TEL
EMS Tape 6", 400 m roll, English
80-6116-1195-7
3M™ Dynatel™ Locators 7000 Series
Marker Tape/Locator 7420
Based on existing Dynatel technology platform, the new 7420 locator will allow
the user to locate EMS Caution Tape and existing electronic markers (balls, nearsurface, full range, etc.). In addition, the locator will read/write to 3M ID markers.
It is as easy as selecting “path” marker locating for EMS Caution Tape or “ID/EMS”
for point marker locating. The push of one button will provide the depth to any of
the underground marking solutions.
Pipe/Cable/EMS Locators 7550-ID
Pipe/Cable/Fault/EMS Locators 7573-ID
3M™ Dynatel™ locators 7500 series offer a broad feature set with advanced digital
processing and simple interfaces with precision locating capabilities. The new
7500 series locators will allow the user to locate EMS Caution Tape and existing
electronic markers (balls, near-surface, full range, etc.). In addition, all 7500 series
locators will read/write to 3M ID markers. All 7500 series locators offer six active
frequencies and transmitter output options in 3, 5 or 12 watts providing a solution
for virtually all challenging applications encountered in the field.
As with all 3M Dynatel Cable/Pipe Locators, the 7500 series provides accurate pipe,
cable, or Sonde depth measurements, giving a digital readout in feet and inches,
or centimeters (user-selectable). All 7500 series locators and fault finders are also
compatible with select GPS/GIS field mapping instruments for real time mapping
of electronic markers or pipe and cable facilities. Other user friendly features include
the ability to enable or disable receiver frequencies and the ability to select audio
sounds in the simple menu driven interface.
A Reputation of Excellence
When you choose a quality 3M™ Dynatel™ Locator, you get outstanding performance
and reliability, along with toll-free technical phone support and a service center
dedicated to excellence. Our service center provides calibration, repair, upgrades
and modifications for safety, performance and reliability.
3M™ Dynatel™ Cable/Pipe/Fault/EMS
Locator 7500 Series
Product Features
• 6 active frequencies for direct
connect
• 4 induction frequencies with
maximum allowed output power
• Trace view mapping display
• Push button depth to all underground
markers (passive and ID)
• Receiver rechargeable battery kit
• All frequency mode in direct connect
(4 simultaneously)
• Automatic impedance matching
• Ohm meter with high voltage
detection
• Rugged, industrial temperature range
• 240VAC output protection
New features in the 3M™ Dynatel™
7500 Series Locators include EMS
Caution Tape Locating and EMS alert
which allows the user to locate EMS
Caution Tape and at the same time be
alerted to electronic markers of the
same utility.
3M™ Dynatel™ Cable/Pipe/Fault/EMS Locator 7500 Series


3W

4.5"

80-6300-0272-5
7550-ID/U5
Pipe/Cable/EMS Lctr Util 4.5" Cplr 5W


5W

4.5"

80-6300-0273-3
7550-ID/U12
Pipe/Cable/EMS Lctr Util 4.5" Cplr 12W


12W

4.5"

80-6300-0274-1
7550-ID/5-NA
Pipe/Cable/EMS Lctr 5W (No accys)


5W
80-6300-0275-8
7573-ID/U3
Pipe/Cable/Fault/EMS Lctr Util 4.5" Cplr 3W



3W

4.5"

80-6300-0276-6
7573-ID/U5
Pipe/Cable/Fault/EMS Lctr Util 4.5" Cplr 5W



5W

4.5"

80-6300-0277-4
7573-ID/U12
Pipe/Cable/Fault/EMS Lctr Util 4.5" Cplr 12W



12W

4.5"

80-6300-0278-2
7573-ID/C3
Cable/Pipe/Fault/EMS Lctr Com 3" Cplr 3W



3W

3"
80-6300-0279-0
7573-ID/C5
Cable/Pipe/Fault/EMS Lctr Com 3" Cplr 5W



5W

80-6300-0280-8
7573-ID/C12
Cable/Pipe/Fault/EMS Lctr Com 3" Cplr 12W



12W

80-6300-0281-6
7573-ID/5-NA
Pipe/Cable/Fault/EMS Lctr 5W (No accys)



5W
80-6300-0324-4
7550-ID/UR
Cable/Pipe/EMS Receiver Only


80-6300-0326-9
7573-ID/UR
Cable/Pipe/Fault/EMS Receiver Only


Cigarette Lighter Adapter
Pipe/Cable/EMS Lctr Util 4.5" Cplr 3W
Carrying Bag
7550-ID/U3
Ground Rod
80-6300-0271-7
A-Frame/A-Frame Cable
Coupler Cable
EMS Marker/Tape Locator/Read/Write
2200RB Rechargeable Battery
Coupler Size
Direct Connect Cable - small clips
Direct Connect Cable - large clips
7420
Stock No.
Earth Return Fault Locate
8066113-8923-2
Cable/Pipe Locate
Transmitter Output
3M Passive/ID & Caution Tape Marker Locate
3M™ Dynatel™ Locators and Fault finders 7500 Series Ordering Information










US Version Locators
Stock No.



















3"





3"






Export Version Locators
80-6113-8924-0
7420-E
EMS Marker/Tape Loctator/Read/Write
80-6300-0295-6
7550E-ID/CU5
Cable/Pipe/EMS Lctr Com/Util 3" Cplr 5W



5W


3"





80-6300-0296-4
7550E-ID/CU12
Cable/Pipe/EMS Lctr Com/Util 3" Cplr 12W



12W


3"





80-6300-0297-2
7573E-ID/CU5
Cable/Pipe/Fault/EMS Lctr Com/Util 3" Cplr 5W



5W


3"






80-6300-0298-0
7573E-ID/CU12
Cable/Pipe/Fault/EMS Lctr Com/Util 3" Cplr 12W



12W


3"






80-6300-0325-1
7550E-ID/R
Cable/Pipe/EMS Receiver Only (Export)



80-6300-0327-7
7573E-ID/R
Cable/Pipe/Fault/EMS Receiver Only (Export)




Optional/Replacement Accessories
Stock Number
Product Number
Product Description
80610074686
3001
Dyna-Coupler 3-Inch
80610764716
3019
Cable Locator Coupler Accessory Kit 3"
80611325830
4001
Dyna-Coupler 4.5 Inch
80611335201
4519
Locator Coupler Accessory Kit - 4.5"
80610411185
1196
6" Dyna-Coupler W/Pouch
80611312499
1196/C
6" Dyna-Coupler W/Pouch & 9011 Coupler Cable
80610598130
2876
Large Clip Direct-Connect Trnsmtr Cable for Cable/Fault Locators
80610598668
2892
Small Clip Direct-Connect Trnsmtr Cable for Cable/Fault Locators
80610074850
9012
Direct Connect, 5-Foot Transmitter Cable, Telephone
80610074843
9011
Coupler Cable
80610126833
9043
Ground Extension Cable 12'
80611330368
2200M-USB
USB To RS232 Converter For 2200M/1420 Locators
80610074777
3014
Earth Contact Frame
80610074942
9026
Earth Contact Frame Cable
80611146715
2200M/7000
Soft Carrying Bag For 2200M/2500/7000 Series
80611306517
2200/7000RB
Rechargeable Battery for 5W & 12W Units Non-Spillable
80630002535
7000RB
Rechargeable Battery Pack for 7000 Series Rcvr
80610126841
8006
Ground Rod
80610757785
3229
ADP 33 kHz Sonde for Use w/Cable/Fault Locators
3M™ Dynatel™ EMS Marker/Tape Locator 7420/7420E Product Specifications
Physical Specifications:
Locator
Shipping Box
Size (H x W x D) IN (CM)
30" x 6.5" x 10.5" (76 x 17 x 27)
Size (L x W x H) IN (CM)
33" x 17" x 12.5" (84 x 43 x 32)
Weight (including batteries)
5 lb. (2.25 kg)
7 lb. (3.2 kg)
Environmental Specifications:
Operating temperature
Storage temperature
Regulatory
Environmental Standard
-4° F to 122° F (-20° C to 50° C)
-4° F to 158° F (-20° C to 70° C)
7420 (FCC Part 15), 7420E (CE)
IP54
Compatibility:
3M EMS/ID Markers
3M EMS 7600 Series Caution Tape
All 3M markers (telephone, gas, communication, power, water, wastewater and general purpose)
All 3M path marking caution tape (telephone, gas, wastewater)
Range/Depth:
Write Range
3M ID Markers:
Near-Surface
Ball Marker
Full-Range
6 in. (15 cm)
12 in. (30 cm)
24 in. (61 cm)
7420 Read Range
3M ID Markers:
(Telephone, Power, Gas, Water, Wastewater, Communications (CATV), General Purpose)1
Near-Surface
Ball Marker
Full-Range
3 ft. (0.9 m)
5 ft. (1.5 m)
8 ft. (2.4 m)
7420E Read
3M ID Markers:
(Telephone, Gas, Wastewater, Water, Communications (CATV), General Purpose)*
Near-Surface
Ball Marker
Full-Range
90 cm (36 in.)
1.5 m (60 in.)
2.4 m (94 in.)
* Some countries do not allow all marker operating frequencies. Refer to the Operator's Manual for more information.
Detection Depth 3M Passive Markers (no ID):
Near-Surface
Ball Marker
Mid-Range
Full-Range
3 ft. (0.9 m)
6 ft. (1.8 m)
7 ft. (2.1 m)
9 ft. (2.75 m)
Maximum Burial Depth
7600 Series Caution Tape
Depth measurement accuracy
2.0 ft. (.61 m)
+/- (10% + 5 cm) or +/- (10% + 2 in.) up to specified depth of marker or caution tape
(Depth accuracy susceptible to high ambient noise conditions)
ID Marker Memory Storage:
Memory storage with date/time stamp
Written marker records
User defined ID templates
Marker depth memory storage
Read marker records 100
100
32
Five with date/time stamp
Electrical Specifications:
Power
Battery life:
Charging time
Display
Speaker
Headphone jack
Serial port
Rechargeable battery pack (12V2R4A)2
8 hours typical3
2.5 hours, with 90~240V AC adapter
Large graphic high-contrast LCD with backlight
0.25 W
Standard mini phone jack
Standard RS232 serial with DB9 connector(RS232 to USB adapter cable included)
Notes:
1
Some countries do not allow all marker operating frequencies. Refer to configuration section for 7420E instruction manual (Section 4A).
2
It’s recommended to use the rechargeable battery pack. However, a battery holder is provided for using 8-AA size Alkaline batteries for backup,
which would have reduced battery life.
3
The battery life is measured for the 12V2R4 rechargeable battery pack at 73°F/23°C, with 10% usage of the backlight and audio volume at medium level.
3M™ Dynatel™ Pipe/Cable/Fault/EMS Locator 7500 Series Product Specifications
Physical Specifications:
Locator
Shipping Box
Size (H x W x D) IN (CM)
30” x 6.5” x 10.5” (76 x 17 x 27)
Size (L x W x H) IN (CM)
33” x 17” x 12.5” (84 x 43 x 32)
Weight (including
batteries)
6.4 lb. (2.90 kg)
7 lb. (3.2 kg)
Environmental Specifications:
Operating temperature
Storage temperature
Regulatory
Environmental Standard
-4° F to 122° F (-20° C to 50° C)
-4° F to 158° F (-20° C to 70° C)
7550 (FCC Part 15), 7550E (CE)
7573 (FCC Part 15), 7573E (CE)
IP54
7500 Series Receiver Specifications
Power
Battery Life
Charging Time
Display
Speaker
Headphone jack
Serial Port
Rechargeable Li Ion battery pack (12V2R4A)1
8 hours typical2
2.5 hours typical, with 90~240V AC adapter
Large graphic high-contrast LCD with backlight
0.25W
Standard mini phone jack
Standard RS232 serial with DB9 connector
(RS232 to USB adapter cable included)
Display
LCD
Gain Control
Manual and Automatic
Weight w/batteries
5.0 - 6.4 lbs. (2.3 - 2.9 kg) (model dependent)
Cable/Pipe Depth Accuracy
±2% ± 3 in. (7.6 cm) for 0–60 in. (1.5 m)
±6% ± 3 in. (7.6 cm) for 60–120 in. (1.5–3.0 m)
±10% ± 3 in. (7.6 cm) for 120–180 in. (3.0 m–4.5 m)
Cable/Pipe Depth Range
0–360 in. (0–914 cm)
Locate Modes:
Trace View
Directional Peak
Directional Null
Special Peak
Induction Peak
Frequency Response:
Active 7550/7573
577 Hz
1 kHz
8 kHz
33 kHz
82 kHz
200 kHz
Active 7550E/7573E International
577 Hz
1 kHz
8 kHz
33 kHz
82 kHz
133 kHz
Passive
31.5 kHz (CATV)
15 – 30 kHz (LF)
Power
50 Hz, 5th and 9th harmonic of 50 Hz
60 Hz, 5th and 9th harmonic of 60 Hz
(100 / 120 Hz) rectified power
Auxiliary
512 Hz
560 Hz
640 Hz
User Defined Frequencies
Four
Marker Compatibility:
3M™ EMS/ID Markers
3M™ EMS 7600 Series Caution Tape
All 3M markers (telephone, gas, communication, power, water, wastewater and general purpose) All 3M
path marking caution tape (telephone, gas, water, waste water)
Write Range
3M™ ID Markers:
(Telephone,Power*, Gas, Water, Wastewater, Communications (CATV), General Purpose)
Near-Surface
Ball Marker
Full-Range
6 in (15 cm)
12 in (30 cm)
24 in (61 cm)
* The Power frequency is not supported for 7550E/7573E in write mode.
7550/7573 Read Range
3M™ ID Markers:
(Telephone, Power, Gas, Water, Wastewater, Communications (CATV), General Purpose)*
Near-Surface
Ball Marker
Full-Range
3 ft (0.9 m)
5 ft (1.5 m)
8 ft (2.4 m)
7550E/7573E Read Range
3M™ ID Markers:
(Telephone, Water, Gas, Wastewater, Communications (CATV), General Purpose)*
Near-Surface
Ball Marker
Full-Range
90 cm (36 in)
1.5 m (60 in)
2.4 m ( 96 in)
* Some countries do not allow all marker operating frequencies. Refer to Configuration Section for 7550E/7573E (Section 4A).
Detection Depth for Passive Markers (no ID):
Near-Surface
Ball Marker
Mid-Range
Full-Range
3 ft (0.9 m)
6 ft. (1.8 m)
7 ft. (2.1 m)
9 ft. (2.75 m)
Maximum* Burial Depth
7600 Series CT-3 Tape
Depth measurement accuracy
2.0 ft. (.61 m)
+/- (10% + 5 cm) or +/- (10% + 2 in) up to specified depth of marker or caution tape (Depth accuracy
susceptible to high ambient noise conditions) Maximum Burial depth 2.5 ft (.7 m)
ID Marker Memory Storage:
Memory storage with date/time stamp
Written marker records
User defined ID templates
Marker depth memory storage
Read marker records 100
100
32
Five with date/time stamp
Notes:
1. It’s recommended to use the rechargeable battery pack. However, a battery holder is provided for using 8-AA size Alkaline batteries for backup, which would have
reduced battery life.
2. The battery life is specified for the 12V2R4 rechargeable battery pack at 73°F / 23°C, with 10% usage of the backlight and audio volume at medium level.
7500 Series U Version 12-Watt Transmitter Specifications
Item
Specification
Trace Mode
577 Hz
1 kHz
8 kHz
33 kHz
82 kHz
200 kHz
Fault Mode
(7573 models only)
10/20 Hz -Fault signal
577 Hz / 33 kHz -Trace signal.
Tone Mode
(7573 models only)
577 Hz and 200 kHz pulsing at 8 Hz
Induction Mode
8 kHz
33 kHz
82 kHz
200 kHz
Output Power
(in Direct Connect mode)
Normal setting: 0.5 W
High setting: 3 W @ 577 Hz, 1 kHz, 8 kHz, 33 kHz; 1 W @ 82 kHz, 200 kHz
Maximum setting: 12 W @ 577 Hz, 1 kHz, 8 kHz; 10 W @ 33 kHz; 1 W @ 82 kHz, 200 kHz
Output Voltage (Maximum)
70 Vrms
Item
Specification
Output Protection
240 Vrms
Weight with batteries
with alkaline batteries only: 5.2 lbs (2.4 kg)
with rechargeable battery and alkaline batteries: 9.2 lbs (4.2 kg)
Battery Qty. and size
For Normal and High Output Power: 6 "C" size, Alkaline (LR14)
For Maximum Output Power: Rechargeable Battery, 12V-6AH, Sealed Maintenance-Free Lead (Pb)-Acid Battery
Typical Battery Life
Normal Output Power level: 50 hours
High Output Power level: 10 hours
Typical transmitter specified battery life (listed above) is increased by 40% when using the 2200RB Rechargeable
Battery (12 volt). Using the 2200RB bypasses the alkaline batteries.
Maximum Output Power level: 4 hours (Maximum Output Power level achieved using 2200RB Rechargeable Battery.)
External DC Power
9–18 V DC
Standard
IP54
Regulatory
FCC compliant, FCC Part 15
Operating Temperature
4°F to 122°F (-20°C to 50°C)
Storage Temperature
-4°F to 158°F (-20°C to 70°C)
Rechargeable Battery Fuse
5 Amp / 32 Volt Littelfuse MINI® Blade # 0297005
Cigarette Lighter Adapter Cable Fuse
4 Amp/Fast Blow 250V
7500 Series E Version 12-Watt Transmitter Specifications
Item
Specification
Trace Mode
577 Hz
1 kHz
8 kHz
33 kHz
82 kHz
133 kHz
Fault Mode - (7573 models only)
10/20 Hz -Fault signal
577 Hz / 33 kHz -Trace signal
Note: The fault locating limit is 2.0MΩ, although the transmitter's ohm-meter mode can display a fault resistance up
to 10MΩ.
Tone Mode - (7573 models only)
577 Hz and 200 kHz pulsing at 8 Hz
Induction Mode
8 kHz
33 kHz
82 kHz
133 kHz
Output Power
(in Direct Connect mode)
Normal setting: 0.5 W
High setting: 3 W @ 577 Hz, 1 kHz, 8 kHz, 33 kHz; 1 W @ 82 kHz, 133 kHz
Maximum setting: 12 W @ 577 Hz, 1 kHz, 8 kHz; 10 W @ 33 kHz; 1 W @ 82 kHz, 133 kHz (with external DC power source)
Output Voltage (Maximum)
70 Vrms
Output Protection
240 Vrms
Weight w/batteries
with alkaline batteries only: 5.2 lbs (2.4 kg)
with rechargeable battery (2200RB) and alkaline batteries: 9.2 lbs (4.2 kg)
Battery Qty. and size
For Normal and High Output Power: 6 "C" size, Alkaline (LR14)
For Maximum Output Power: Rechargeable Battery (2200RB), 12V-6AH, Sealed Maintenance-Free Lead (Pb)-Acid
Battery (See safety information below.)
Typical Battery Life
Normal Output Power level: 50 hours
High Output Power level: 10 hours
Typical transmitter specified battery life (listed above) is increased by 40% when using the 2200RB Rechargeable
Battery (12 volt). Using the 2200RB bypasses the alkaline batteries.
Maximum Output Power level: 4 hours (Maximum Output Power level achieved using 2200RB Rechargeable Battery.)
External DC Power
9–18 V DC
Standard
IP54
Regulatory
CE Compliant
Operating Temperature
4°F to 122°F (-20°C to 50°C)
Rechargeable Battery Fuse
5 Amp / 32 Volt, Littelfuse MINI® Blade # 0297005
Cigarette Lighter Adapter Cable Fuse
4 Amp/Fast Blow 250V
3M and Dynatel are trademarks of 3M Company.
Conditional Limited Warranty
3M provides the following Conditional Limited Warranty for its EMS Caution Tape 7600 Series Products: When installed in accordance with 3M’s installation instructions, 3M
warrants EMS Caution Tape for a period of one (1) year from the date of purchase of the product, to be free from defects in material and manufacture, provided EMS Caution
Tape is located with 3M™ Dynatel™ Locators or other brand locators as may be designated by 3M in writing. This warranty does not extend to EMS Caution Tape that has been
subjected to misuse or improper application or that have been repaired or altered by others. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE. If the EMS Caution Tape is found to be defective within the warranty period, your exclusive remedy
shall be, at 3M’s options, to repair or replace the EMS Caution Tape or refund the purchase price. Except where prohibited by law, 3M will not be liable for any indirect, special,
incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
Conditional Limited Warranty
3M provides the following Conditional Limited Warranty for its ID Electronic Marker Products: When installed in accordance with 3M’s installation instructions, 3M warrants ID
Electronic Markers for a period of ten (10) years from the date of purchase of the product, to be free from defects in material and manufacture, provided ID Electronic Markers
are located with 3M™ Dynatel™ Locators or other brand locators as may be designated by 3M in writing. This warranty does not extend to ID Electronic Markers that have been
subjected to misuse or improper application or that have been repaired or altered by others. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE. If the ID Marker is found to be defective within the warranty period, your exclusive remedy shall
be, at 3M’s options, to repair or replace the ID Markers or refund the purchase price. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or
consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
Conditional Lifetime Warranty
3M provides the following Conditional Limited Warranty for its Electronic Marker Products (non-ID versions only): When installed in accordance with 3M’s installation instructions, 3M warrants Electronic Markers for the lifetime of the product, to be free from defects in material and manufacture, provided the Electronic Markers are located with 3M™
Dynatel™ Locators or other brand locators as may be designated by 3M in writing. This warranty does not extend to Electronic Markers that have been subjected to misuse
or improper application or that have been repaired or altered by others. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE. If the Electronic Marker is found to be defective during the normal lifetime of the product, your exclusive remedy
shall be, at 3M’s options, to repair or replace the Electronic Markers or refund the purchase price. Except where prohibited by law, 3M will not be liable for any indirect, special,
incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
Conditional Limited Warranty
Locating instruments (except accessories), manufacture dated test leads, and rechargeable batteries will conform to 3M’s published specifications and will be free from defects
in material and manufacture for a period of twelve (12) months from the date of purchase. Dry cell batteries included in any of 3M’s products are warranted only to the extent
the battery manufacturer determines such batteries are covered by its warranty. Accessories for locating instruments are warranted for ninety (90) days after purchase. 3M’s
obligations and liability under this warranty are limited to repairing, replacing or refund of the purchase price, at 3M’s option, any of 3M’s products which, after normal and
proper usage, are determined by 3M to be defective. This warranty does not extend to any of 3M’s products which have been subjected to misuse, neglect, accident or improper
applications, nor shall it extend to products which have been repaired or substantially altered outside 3M’s manufacturing or repair facility, nor to any associated instruments,
equipment or apparatus. Before utilizing any of 3M’s products, BUYER should determine the suitability of the product for BUYER’S intended use. 3M MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. In no case shall 3M be liable for any
special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory. This limitation does not apply
to claims for personal injury.
3
Electrical Markets Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/200-0265
Fax 877/601-1305
www.3M.com/dynatel
Please recycle. Printed in USA.
© 3M 2014. All rights reserved.
78-9000-0400-9
Download PDF