Dual | XML8110 | Owner`s manual | Dual XML8110 Owner`s manual

XML8110
INSTALLATION/OWNER1S MANUAL
In-Dash AM/FM/Bluetooth® Ready Docking Station
IDl
Madefor
@J
iPod
oBluetooth®
READY
Dual
. . XML8110 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures. such as from
direct sunlight. or where it would be subject to dust. dirt or excessive vibration.
Getting Started
• Remove trim ring from unit.
• Insert the supplied keys into the
slots as shown. and slide the unit
out of the mounting sleeve.
• Install mounting sleeve into
opening. bending tabs to secure.
• Connect wiring harness and
antenna. Consult a qualified
technician if you are unsure.
• Certain vehicles may require an
installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide
into mounting sleeve to secure.
• Snap trim ring into place.
KEYS
MOUNTING STRAP
./
~
HEX BOLT
.~
MOUNTING SLEEVE
lYPICAL FRONT-LOAD DIN MOUNTING METHOD
2
HEX NUT
PLAIN WASHER
XML8110 INSTALLATION . .
Wiring Diagram
BLACK 8-pin Female Mini-DIN
B'TIo46O Connection <sold " _..tely)
FRONT RCA Preamp Output
RCA Preamp Connections
REAR/SUB Preamp Output - - -....
<_bIo)
,..,---
RCA Auxiliary Input
I
GREEN 8-pin Male Mini-DIN
Emmlll Aa:usory Connoctlon
~
Steering Wheel Interface Input
(PAC SWI-PS required)
I
BLUE Remote Tum-On
I
Connect to amplifier or power
antenna. Insulate wire if not used.
BLACK Ground
I
Connect to vehicle
chassis ground.
RED Accessory
I
~
Connect to existing ignition
circuit or switched 12 volt source.
YELLOW Memory
0
Connect to battery
circuit or constant 12 volt source.
FUSE
When replacing the fuse.
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XML8110 uses one
10 amp ATM fuse located
Right Front
Right Rear
Gray/Black H
Gray (+)
VioleVBlack (-)
Violet (+)
Left Front
Left Rear
While/Black H
White(+)
Green/Black H
Green (+)
beside the wiring connector.
3
g'
XML811 0 OPERATION
Control Locations - Receiver (Closed)
G) Volume
G) Power
(1) Tune / Track Down
G) Mode
@
@
@
Preset4
® Audio / Menu
©
End Call / Mute
G)
@
@
@
(j)
(!)
4
Talk
Preset 1
Preset 2
G)
Preset 3
Preset 6
Preset 5
Display
Tune / Track Up
Band
XML8110 OPERATION . .
Control Locations - Receiver (Open)
CD LCD Display
CD Dock for iPod®
CD Expansion Slot
CD Tune / Track Up
CD Mode
CD Play / Pause
(j)
Tune / Track Down
CD
CD
End Call / Mute
@
Volume Down
®
Volume Up
@
Reset
Talk
5
E
XML8110 OPERATION
Control Locations - Remote
CD
CD
CD
CD
®
CD
6
Power (C»)/Select
@
@
Volume Up
@
Key 0 / Display
Audio / Menu
®
Talk
Mode
Tune / Track Up
@
Volume Down
®
®
®
®
®
(j)
(i)
Sea n / PS / Key #
CD
Preset 3 / Intro
Preset 2 / Random
@
Preset 6 / Folder Up
@
Preset 5 / Folder Down
Key 9
Mute / End Call
KeyS
Key 7
Preset 4 / Play / Pause
Preset 1 / Repeat
Band / ESC / Key *
Tune / Track Down
XML81100PERATION
-_._._~.~~
_
~
~_
~._
_
~_
.._.
[II
----------_.
General Operation
Power OnlOff
Mode
Press the red power button or any other button to turn the
unit on. Press and hold the red power button to turn the unit
off.
Press MODE to select between AM/FM. Auxiliary input.
Bluetooth and operation of iPod modes. Modes of operation
are indicated in the display.
Note: Operation of iPod mode will not appear unless an iPod
device has been connected using the in-dash dock located
behind the front panel. Bluetooth mode will not appear
unless the BTM60 Bluetooth module is connected.
Steering Wheel Interface
Input
The steering wheel interface input located on the back of the
head unit allows connection to the PAC (Pacific Accessory
Corporation) SWI-PS interface module (sold separately). Visit
www.pac-audio.com for details.
To configure steering wheel controls. follow the instructions
provided with the PAC SWI-PS interface module. After
installing the interface module. insert the module's 3.5mm
jack into the port on the back of the head unit.
Volume
Mute
Reset
Display
Set the Clock
12124-Hour Clock
Expansion Slot
Adjust volume using volume knob (00-46).
Press ~ to silence the audio. "MUTE" will flash in the
display. Press ~ again to cancel.
Press to RESET the unit upon initial installation or if
abnormal operation occurs. The reset button is located to the
right of the dock. with the front panel open.
Press DISP to toggle between items such as clock and radio
frequency.
With the unit on. press and hold DISP until the clock begins
to flash. then release. Press TUNE ~~ to adjust the
hours and TUNE ~~ to adjust the minutes. Press DISP
momentarily to save the selected time.
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10:00). In European frequency spacing
mode. the clock will display 24-hour time (22:00).
The expansion slot provides an easy way to upgrade the
XML8110 with new features. Check www.dualav.com for
more details.
7
. .XML811 0 OPERATION
General Operation
Setup Menu
Menu Exit
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu. then press AUDIO/MENU to cycle
through menu options. When desired option appears in the
display. rotate the volume knob left/right to adjust or activate
the desired function.
Press BAND to exit any menu or submenu.
Setup Menu
··'Meftu·F~on,';;
Auto Station
Store
Tuner Frequency
Spacing
Auxiliary
Input
Rear/Sub
RCA output
Loudness
Curve
Clock
Display
Beep Confirmation
Auto Store
Frequency US
Programs unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM)
Frequency EU
Programs unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
Auxiliary On
Enables the rear RCA auxiliary input.
Auxiliary Off
Disables the auxiliary input.
Rear/Sub Sub
Programs the Rear/Sub RCA preamp output to rear.
Rear/Sub Rear
Programs the Rear/Sub RCA preamp output to subwoofer.
Loud Off
Disables the loudness function.
Loud On
Enables the loudness function. Activating this feature will enhance the
bass and treble frequencies when listening to music at low volumes.
Clock Off
Programs unit to not display the clock when the power is off.
Clock On
Programs unit to display the clock when the power is off.
Beep Off
Disables the confirmation beep.
Beep On
Enables the confirmation beep.
Programmable
Tum On Volume
Prog-Vol #
LocaVDistance
Tuning
Local Off
Activates distance tuning.
Local On
Activates local tuning for strong station reception only.
Power on Message
Scrolling
Option
Illumination
Dimmer
Demonstration
Mode
Programs unit to turn on at a specific volume
(default is OFF).
Message Off
Disables power on message.
1----=----1------:------=-----------------1
Message On
Enables power on message to be displayed.
Scroll Once
8
Press the center SELECT to seek and save 6 strong stations in the current band. Note: This option only appears in Tuner mode.
Programs unit to scroll once. then show the first 10 characters on the
display.
Scroll On
Programs unit to scroll continuously.
Scroll Off
Programs unit to show the first 10 characters on the display.
Dimmer High
Programs unit to the brightest illumination level.
Dimmer Mad
Programs unit to the middle illumination level.
Dimmer Low
Programs unit to the dimmest illumination level.
Demo Off
Disables the demonstration message.
Demo On
Enables the demonstration message.
XML8110 OPERATION
1m"
General Operation
Audio
Press AUDIO/MENU momentarily to select between Bass.
Treble. Balance. Fader. EO. Subwoofer* and Source Volume
Level.
C
BASS
~
TREBLE
~
BALANCE
~
FADER
~
EQ
~
SUBWOOFER'
~
SOURCE LEVEL - ,
Bass
Press AUDIO/MENU until Bass appears. then rotate the
volume knob left/right to adjust (-6 minimum / +6 maximum).
Treble
Press AUDIO/MENU until Treble appears. then rotate the
volume knob left/right to adjust ( -6 minimum / +6 maximum).
Note: Any adjustment to the Bass or Treble settings are
automatically saved as the User EO.
Bass and Treble settings are retained for each mode
individually.
Balance
Fader
EQ
Source Volume Level
Press AUDIO/MENU until Balance appears. then rotate the
volume knob left/right to adjust L12 (left) to R12 (right),
Balance L=R represents equal balance.
Press AUDIO/MENU until Fader appears. then rotate the
volume knob left/right to adjust (F12 (front) to R12 (rear).
Fader F=R represents equal fader.
Press AUDIO/MENU until EQ appears. then rotate the volume
knob left/right to select between Flat. Pop. Rock. Jazz. Classic.
Beat or User equalization curves. Any adjustment to the Bass
or Treble settings are automatically saved as the User preset
EO.
The source volume level control allows a gain adjustment for
each audio source: AM. FM. Auxiliary input. operation of iPod
and Bluetooth. Set the source volume level for each mode.
depending on the relative volume of each audio source.
To set the source volume level. press AUDIO/MENU until
SRC LEVEL appears. After one second. the current mode will
appear on the display. Turn the volume knob to adjust the
audio level of the current source (-6 minimum/+6 maximum).
Note: Only the current mode will be available for adjustment.
To adjust another mode of operation. press MODE until the
desired mode is selected. then set the source volume level for
that mode.
Subwoofer
Press AUDIO/MENU until Sub-W appears. then press SELECT
to confirm. Rotate volume knob left/right to adjust (0-12).
Adjusting levels to 0 turns the subwoofer off.
9
. . XML8110 OPERATION
AM/FM Tuner Operation
Seek Tuning
Manual Tuning
Band
10
Press TUNE ........ or TUNE ~~ for more than one second to
seek the next strong station.
Press TUNE ........ or TUNE ~~ momentariLy to move radio
frequency up or down one step at a time. Press and hoLd to
advance quickLy.
Press BAND to seLect between FM1. FM2. FM3. AM1 and
I AM2 bands. Up to six presets can be saved for each band.
Storing and Recalling
Station Presets
Up to 18 FM stations and 12 AM stations can be stored. To
store a station. seLect the desired band and station. Press
and hoLd the desired preset button (1-6) for more than
two seconds. When stored. a box will appear around the
corresponding preset number in the dispLay. The station can
be recalled anytime by pressing the corresponding preset
button.
Auto Station Store
To automatically store the 6 strongest stations to preset
buttons 1-6 in the current band. press and hoLd AUDIO!
MENU from tuner mode to enter the setup menu. While
"Auto Store" is flashing on the dispLay. press the center
seLect button to begin the automatic station storing process.
XML8110 OPERATION . .
Dock for iPod - Operation
To open the XML811 0 and use
the dock. pull outward from the
top of the front panel.
The front panel will rotate open.
Continue rotating the front
panel downward.
The front lIanel stops when it
reaches the fully open position.
11
. . XML811 0 OPERATION
Dock for iPod - Operation
For the 1st generation. 2nd generation and 4th
generation iPod nano devices. the left side dock
support can be replaced with a larger rubber
support. for the best fit.
Some iPod devices have a thinner design. and
may require changing the rear rubber support at
the back of the dock for the best fit.
To change the rear rubber support. pull upward
on support to remove it. Then replace the support
with the thicker rubber support that is included
in the box.
To change the left side rubber support. pull
outward on the rubber support to remove it. Then
replace the support with the larger rubber support
that is included in the box.
I
To dock an iPod device, first spread apart the side
supports of the dock. Then line up the dock connector
and insert the iPod device into the dock. Release the
side supports to secure the iPod device.
12
XML8110 OPERATION . .
Operation of iPod
Using the In-Dash
Dock for iPod
Control of iPod
Song Select
Pause
Volume
Insert the iPod device into the XML811 D's Docking Station
following the instructions on pages 11 and 12.
The iPod device can be controlled directly from the iPod
device controls. or controlled using the inside panel
buttons shown below:
Press ~~ to skip to the beginning of the next song.
Press........ to return to the lJeginntng of the current song.
Pressing........ again skips to the beginning of the previous
song.
Press ~/II to temporarily stop playback.
Press ~/II again to resume playback.
During playback. the volume is adjustable using the
volume controls on inside panel. When connected. the
volume controls on the iPod device are not adjustable.
iPod Device Compatibility
i
iO
O
[~I
O
[~I
O
~
o"""
iPod
4th generation
20GB
iPod
4th generation
40GB
;Podgeneration (color display)
4th
20GB 30GB
;Pod
4th generation (color display)
40GB 60GB
iPod nano
1st generation
1GB 2GB 4GB
-.t.
~O
-.t.
~O
"""
~
@
[I "'" II
®
iPod
5th generation (video)
30GB
iPod
5th generation (video)
60GB 80GB
iPod nano
2nd generation (aluminum)
2GB 4GB 8GB
;Pod c1.,,;c
80GB 160GB
CJ
o
[I"'@" II
@
o
;Pod c1.,,;c
120GB
~...t.
iPod nano
@
8GB 16GB
~ 4th generation (video)
CJ
o
[1""'1]
iPod touch
1st generation
8GB 16GB 32GB
iPod touch
2nd generation
8GB 16GB 32GB
iPod nano
3rd generation (video)
4GB 8GB
13
. . XML81100PERATION
Bluetooth® Operation
Overview
Connecting a Bluetooth device requires first installing and connecting the Dual BTM60
Bluetooth interface module (sold separately). When connected to a Dual Bluetooth ready
head unit. the BTMbO supports the HFP (hands-free profile). A2DP (advanced audio
distribution profile) and AVRCP (audio video remote control profile).
Preparation
Before you can use a mobile device with this head unit. it must be paired and connected.
Please make sure that Bluetooth is activated on your mobile device before you begin the
pairing process. Refer to the owner's manual of your mobile device for more details.
Bluetooth Pairing
1) To pair a Bluetooth enabled mobile phone to your head unit. press \. on the head unit
or BTMbO. or press MODE until "DUAL_BTMbO" is displayed.
2) Press and hold \. on the head unit or BTMbO for 5 seconds. until "PAIRING" is
displayed. the Bluetooth icon will flash every second. The head unit will begin to
broadcast the pairing signal for 90 seconds.
3) Complete the pairing from the Bluetooth menu of your mobile device by searching
for new devices. Please refer to your mobile device instructions for further information
on Bluetooth pairing and connections. The Bluetooth icon will illuminate solid when
connected.
The BTM60 device name is -DUAL_BTM60.The password for the DUAL BTM60 is 1234.
Paired Devices List
The XML811 0 will remember the last 8 devices that were paried. To access the list of
previously paired devices. follow these instructions:
•
•
•
•
•
Disconnect any mobile device that may be connected by pressing"" once.
Press DISP momentarily to cycle through the list of 8 previously paired devices.
When stopped on a device number 1-8. wait 5 seconds to see the name of the device.
If the device is not in range of the BTM60. "Unknown" will be displayed.
Once the desired device is displayed. press \. or the center select button to connect.
Connection Notes
• If AUTO-CON is set to OFF you must press \. to connect after pairing. and every time
the XML811 0 is turned on.
• From Bluetooth standby mode. press,.,. to disconnect your mobile device from the
BTMbO. If disconnected. press \. to reconnect the mobile device that was connected last to
the BTMbO.
Compatibility
• Due to the differences in Bluetooth technology. some mobile devices may be
incompatible or function improperly when used with the BTMbO.
14
XML8110 OPERATION . .
Bluetooth® Operation
Press \,. once. "Enter Number" will be shown. then An "_" will
appear on the display.
Input the desired phone number using the 0-9. *. # buttons on the
Making a Phone Call remote controL. Press \,. to begin dialing.
t------------:.----=-----------I
A phone call may also be placed from your mobile device using
the keypad. phone book or speed diaL. When a call is placed from
a mobile device. "DIALING" will appear on the head unit display.
If an incoming call is detected. the head unit will automatically
switch to Bluetooth mode. muting any current audio.
Receiving a Phone
Call
The incoming phone number will scroll across the display. the
phone icon will flash on the display. and a ring tone will be
audible from the vehicle speakers. See Bluetooth Settings for
speaker configurations.
Note The ring audio level will depend the mobile device and head
unit ring volume and audio settings. If the ringer on the mobile
device is off. you may not hear an incoming ring tone.
Press \,. to receive a calL. The phone icon in the display will
illuminate.
The head unit will display the elapsed time of the phone call.
During a Phone Call The volume knob will adjust the volume of the calL.
t------------':....----------------I
Press ~ to mute the BTM60's microphone during a call.
Refusing a Call
To refuse an incoming phone call. press and hold" for 3
seconds.
Hold" for 3 or more seconds to end a call.
Ending a Phone Call If the phone call was received. the head unit will return to
previous mode when call is ended.
15
. . XML8110 OPERATION
Bluetooth® Operation
: ~". Despription,:
To view the 10 most recent calls. press \.. then press \. a second
time. "Recent Calls" will be displayed.
Recent Call List
A list of the most recent missed. dialed. or received calls will appear.
sorted by time. beginning with the most recent call.
or........
Press ~~
to cycle through the list of recent calls. When
the desired number appears on the display. press the center select
button or \. to dial the phone number.
Audio Transfer
To transfer the phone call between the head unit and the mobile
device. press and hold DISP for 3 seconds during a call. Tip: transfer
audio to your mobile device before turning the head unit off.
Call Waiting
When a second call is incoming. press \. to activate call waiting. The
current call will be placed on hold. and the second call will be active.
Press \. again to return to the first call.
Call Hold
Press \. to place the current call on hold. To resume the phone call.
press \. again.
Bluetooth Setup Menu
Bluetooth Mode
Bluetooth ON
Enables the BTM60 Bluetooth Interface Module
(included). The Bluetooth icon will flash every 10
seconds when a device is not connected.
Bluetooth OFF
Disables Bluetooth support.
Auto-Con ON
Allows the BTM60 to automatically (re)connect to the
most recently connected mobile device. Note: Some
mobile devices do not support this feature.
Auto-Con OFF
Disables the auto connect feature. You must press \.
every time to connect a mobile device.
Auto-Ans OFF
Disables the auto answer feature. Press \. to
receive an incoming call.
Auto-Ans ON
All incoming calls will be answered automatically without notification.
Speaker 2-CH
Directs the Bluetooth audio to the front speakers.
Speaker 4-CH
Directs the Bluetooth audio to all 4 speakers.
Auto Conned
Auto Answer
Bluetooth Audio
*See page 7 for Setup Menu navigation
16
XML81100PERATION
•
Bluetooth® Operation
Bluetooth Streaming Audio Operation
The XML811 0 supports A2DP (advanced audio distribution profile) wireless streaming
audio from your Bluetooth mobile device directly to your head unit. You can also control
your music from the front panel of the head unit using AVRCP (audio video remote control
profile).
Notes:
• To stream music to your head unit. your mobile device must support A2DP and AVRCP
Bluetooth profiles. Check the owner's manual of your mobile device
• Streaming audio must be enabled from your mobile device. This option will vary
depending on the device. Some devices allow streaming audio to be disabled.
After pairing. connecting and enabling streaming audio from a compatible mobile device.
begin playing music using the music player on your mobile device. Once the music is
playing. the following functions can be used to control music:
XML8110 front panel:
• The ~~ button will skip to the next available audio track.
• The ........ button will skip to the previous audio track.
• The BAND button will toggle between play and pause during playback.
• The""" button will stop the audio playback.
Remote control:
• The ~~ button will skip to the next available audio track.
• The ........ button will skip to the previous audio track.
• The ~/II button will toggle between play and pause during playback.
• The,..... button will stop the audio playback.
Bluetooth Reset
Resetting the Bluetooth module will remove the list of paired phones and delete the list of
recent dialed. received. and missed calls from memory.
To reset the BTM60 Bluetooth module. press MODE to enter Bluetooth standby mode.
Press""" to disconnect your mobile device. if it is connected. Press and hold MODE for 3
seconds to reset the BTM60 module. The unit will display "Reset OK" as confirmation.
17
. . XML811 0 OPERATION
Limited One Year Warranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
Dual Electronics Corp. agrees. at our option.
during the warranty period. to repair any defect
in material or workmanship or to furnish an
equal new. renewed or comparable product
(whichever is deemed necessary) in exchange
without charges. subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
Who is covered? This warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
What is covered? This warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs. damage resulting
from accident. misuse. abuse. neglect. product
modification. improper installation. incorrect
line voltage. unauthorized repair or failure to
follow instructions supplied with the product.
or damage occurring during return shipment of
the product.
18
What to do?
1. Before you call for service. check the
troubleshooting guide in your owner's
manual. A slight adjustment of any custom
controls may save you a service call.
2. If you require service during the warranty
period. you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
3. Please describe your problem in writing and
include your name. a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
• Call us toll-free at 1-866-382-5476
• E-mail usatcs@dualav.com
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties. expressed or implied. including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation. liability. right.
claim or remedy in contract or tort. whether
or not arising from the company's negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect. incidental or consequential
damages.
XML8110 OPERATION
g'
Troubleshooting - General
Unit will not tum on
(no power)
Unit has power
(but no sound)
Unit blows fuses
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Check connections for proper
voltage (11-16VDC)
Black wire not connected
Check connection to ground
Fuse blown
Replace fuse
Speaker wires not connected
Check connections at speakers
One or more speaker wires touching
each other or touching chassis ground
Insulate all bare speaker wires
from each other and chassis
ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Speaker wires touching chassis ground
Check for pinched wire
Incorrect fuse rating
Use fuse with correct rating
19
• • XML8110 OPERATION
Specifications
FM Tuner
II· ng range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AM Tuner
Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General
Operating voltage: 11-16 VDC. negative ground
Speaker output impedance: 4-8 ohms
Line output voltage: 2 Volts RMS
Dimensions: 7- x 7- x 2- (178 x 178 x 51 mm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- O.2V. 20Hz-20kHz)
Power Output: 18 Watts RMS x 4 channels at 4 ohms and ~ 1%THO+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
20
XML8110 OPERATION . ,----'
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference. and
(2) this device must accept any interference received. including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device. pursuant to Part 15 of the FCC Rules. These Limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions. may cause
harmful interference to radio communications. However. there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception. which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
21
"
Dual
Dual Electronics Corp.
Toll Free: 1-866-382-5476
www.dualav.com
©201 0 Dual Electronics Corp. All rights reserved.
iPod is a trademark of Apple Inc.. registered in the U.S. and other countries.
"Made for iPod" means that an electronic accessory has been designed to connect specifically to iPod and has been certified
by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG. Inc. and any use of such marks by Namsung is under
license.
Other trademarks and trade names are those of their respective owners.
NSA0909-VOI
Important iPod Dock Information
The iPod dock includes two additional rubber support brackets that may be changed to
accommodate the various sizes of iPod devices. Use the included rubber support brackets to adjust
the iPod dock and securely fit your iPod into the dock.
iPod Touch
iPod Nano
iPod Nano
fj,r
To adjust the depth of the iPod dock and allow for
the proper fit of iPod Touch and iPod Nano
devices. remove the existing rear rubber support
bracket as shown in the illustration above.
To adjust the width of the iPod dock and allow
for the proper fit of certain iPod Nano devices.
remove the existing left side rubber support
bracket as shown in the illustration above.
Replace the bracket with the larger rear rubber
support bracket that is included.
Replace the bracket with the larger left rubber
support bracket that is included.
For use with 1.t generltion. 2nd genultion Ind 4th genen,lion iPod
Nino device. with In offset dock connector
Download PDF