Koganei IBZR8-4E1, IBZR8Z-E, IBZR8Z-PJ3/8J, IBZR8Z-PJJ Manual

Catalog No.BK-V0018
http://www.koganei.co.jp
5-port manifold solenoid valve
PAT.PEND.
The first in the world!
Integrally molded, all-plastic body!
NEW OPTION!!
Quick fitting exhaust port type
Possible to exhaust with tube
piping, from the 3(R) port of the
piping block.
End block with quick fitting exhaust port
1(P), 3(R) piping size
・φ10mm tube
・3/8 inch tube
15
0.5 mm
91
[
Intermediate piping block with quick fitting exhaust port
in ]
35.3 mm
[ 1.390 in]
Intermediate piping block with
quick fitting exhaust port
・φ10mm tube
・3/8 inch tube
Piping block with
quick fitting exhaust port
Thin and lightweight!
Nearly
40%
smaller
⇦
Nearly
Exhaust port
(Integrated muffler)
1(P), 3(R) piping size
57% less
mass than the previous
180 series manifold
iB-ZERO
Easy assembly
Simple Selection
Previous 180 series
* Valve width: 18 mm [0.709 in.]
Its simple configuration makes assembling the manifold a breeze.
Instant assembly → quick delivery
All are integrated fitting types (select from mm:φ4, φ6,φ8 / in: 5/32 , 1/4 , 5/16)
Perfect for cylinder controls from small diameter to about φ80 [3.150 in]
Safety precautions（iB-ZERO）
Always read these precautions carefully before use.
Before selecting and using the products, please read all safety precautions carefully to ensure proper product use.
The safety precautions described below are to help you use the product safely and correctly, and to prevent injury or damage to you,
other people, and assets.
Always adhere to the following safety regulations: ISO4414 (Pneumatic fluid power - General rules and safety requirements for systems
and their components) and JIS B 8370 (General rules relating to pneumatic systems).
Items are ranked as follows according to degree of potential danger or damage: “DANGER”, “WARNING”, “CAUTION”, and “ATTENTION”.
DANGER
Indicates situations that can be clearly predicted as dangerous.
Failure to avoid the situation creates the risk of death or serious injury.
It could also result in damage or destruction of assets.
WARNING
Indicates situations that, while not immediately dangerous, could become dangerous.
Failure to avoid the situation creates the risk of death or serious injury.
It could also result in damage or destruction of assets.
CAUTION
Indicates situations that, while not immediately dangerous, could become dangerous.
Failure to avoid the situation creates the risk of minor or semi-serious injury.
It could also result in damage or destruction of assets.
ATTENTION
While there is little chance of injury, this content refers to points that should be observed for appropriate
use of the product.
■ This product was designed and manufactured for use in general industrial machinery.
■ When selecting and handling equipment, the system designer or another person with sufficient knowledge and experience should
always read the safety precautions, catalog, instruction manual and other literature before commencing operation. Improper handling
is dangerous.
■ After reading the catalog, instruction manual, etc., always keep them in a location where they are readily available for reference to
users of this product.
■ If transferring or lending the product to another person, always attach the catalog, instruction manual, etc., to the product where they
are easily visible, to ensure that the new user can use the product safely and properly.
■ The danger, warning and caution items listed under these safety precautions do not cover all possible contingencies. Read the
catalog and instruction manual carefully, and always keep safety first.
●B
efore supplying air or electricity to the device and before starting
DANGER
operation, always conduct a safety check of the area of machine operation.Unintentional supply of air or electricity could possibly result in
●D
o not use the product for the purposes listed below:
electric shock, or in injury caused by contact with moving parts.
1
. Medical equipment related to maintenance or management
●
D
o not touch terminals, switches, or other parts, while power is turned
of human lives or bodies.
on.Doing so creates the risk of electric shock and malfunction.
2
. M achines or equipment designed for the purpose of
●D
o not allow the product to be thrown into fire. Doing so creates the
moving or transporting people.
risk of explosion and the release of toxic gases.
3
. Critical safety components in mechanical devices.
●
D
o not sit on the product, place your foot on it, or place other objects
This product has not been planned or designed for purposes
on it.Doing so creates the risk of injury due to tripping or the product
that require high levels of safety. Using the product in any of the
tipping over or dropping, resulting in product damage and abnormal,
ways described above creates the risk of loss of human life.
erratic, or runaway operation.
●D
o not use the product in locations with or near dangerous
● When conducting any kind of operation for the product, such as
substances such as flammable or ignitable substances. This product
maintenance, piping connection and disconnection, inspection,
is not explosion-proof. Doing so creates the risk of ignition and fire.
repair, or replacement, always turn off the air supply completely and
●W
hen mounting the product and workpiece, always make sure they
confirm that residual pressure inside the product or in piping
are firmly supported and secured in place. Falling, dropping, or
connected to the product is zero before proceeding. In particular, be
abnormal operation of the product creates the risk of personal injury.
aware that residual air will still be in the air compressor or air storage
●P
eople using a pacemaker or other similar medical devices should
tank. The actuator could abruptly move if residual air pressure
keep a distance of at least one meter away from the product. Getting
remains inside the piping, causing injury.
too close to the product creates the risk of malfunction of a
pacemaker due to the strong magnet built into the product.
●B
efore commencing normal operation, confirm that the valve is in the
●N
ever attempt to modify the product. Abnormal operation can lead to injury, etc.
proper switching position,and only then commence the operation.
●N
ever attempt inappropriate disassembly, assembly or repair of the
Failure to do so could lead to erroneous operation.
product relating to basic construction, or to its performance or to
●
B
efore performing any kind of wiring work, be sure to turn off power.
functions. Doing so creates the risk of injury, electric shock, fire, etc.
Failure to do so creates the risk of electric shock.
●D
o not splash water on the product. Spraying it with water, washing it,
●C
orrectly apply the rated voltage to the solenoid. Applying the wrong
or using it under water could result in malfunction of the product
voltage will make it impossible to obtain the specified function, and
leading to injury, electric shock, fire, etc.
creates the risk of damage to and burnout of the product.
●W
hile the product is in operation, avoid touching it with your hands or
otherwise approaching too close. Also, do not attempt to make any
●D
o not allow lead wires and other cords to become damaged.
adjustments to internal or attached mechanisms, or to perform any
Allowing a cord to become cut, bent excessively, pulled, rolled up,
type of adjustment (manual override, connecting or disconnecting
placed under heavy objects, or squeezed between two objects
cable connectors, adjusting pressure switches, disconnecting tubes
creates the risk of current leaks or defective continuity that can lead
or sealed plugs, etc.) while the product is in operation.
to fire, electric shock, or abnormal operation.
U
nder such conditions, the actuator may move suddenly, creating
●D
o not connect or disconnect connectors while power is turned on.
the risk of personal injury.
Also, never apply unnecessary force to connectors. Doing so creates
the risk of personal injury, device damage, and electric shock due to
abnormal machine operation.
WARNING
●A
lways check the catalog and other reference materials for correct
product wiring and piping. Improper wiring and piping creates the risk
●B
ecause Koganei products are designed for use under a wide variety
of damage to and abnormal operation of the actuator, etc.
of conditions, decisions concerning conformance with a particular
● In initial operations after the equipment has been idle for 48 hours or
system should be made upon the careful evaluation by the person in
more, or has been in storage, there is a possibility that contacting
charge of system design.Assurances concerning expected system
parts may have become stuck, resulting in equipment operation
performance and safety are the responsibility of the designer who
delays or in sudden movements. Before these initial operations,
decides system conformity. Be sure to use the latest catalogs and
always run a test to check that operating performance is normal.
technical materials to study and evaluate specification details, to
●W
hen the device is not used for long periods (over 30 days), it is
consider the possibility of machine breakdown, and to configure a
possible that the contacting parts may have become stuck leading
system that ensures fail-safe safety and reliability.
to slow operation or sudden movements. Check for proper
●D
o not use the product in excess of its specification ranges. Doing so
operation a minimum of once every 30 days.
creates the risk of product breakdown, loss of function, or damage. It
could also drastically reduce operating life.
1
Safety precautions（iB-ZERO）
●F
or double solenoid type (excluding the Tandem 3-port valve), do not
apply current through both solenoids simultaneously. It is impossible
in such a situation to maintain the correct valve position,and the
equipment may operate in an unintended direction, leading to the
possibility of equipment breakdown or personal injury.
● For double solenoid types, due to the valve position when newly
purchased, connected equipment may operate in unintentional
directions,and may lead to damage of the machine, or personal
injury, so prepare countermeasures to avoid danger.
●D
o not locate the solenoid valve and the wiring that controls it near
power lines running a large current, powerful magnetic fields, or
where power surges occur. Doing so could cause erratic operation.
●S
olenoid valves generate surge voltage and electromagnetic waves
at the OFF operation, which can interfere with the operation of
nearby equipment. Use a surge protected solenoid or implement
appropriate surge and electromagnetic protection measures for the
electrical circuitry.
●D
o not use the product at the beach, in direct sunlight, near mercury
vapor lamps, or near equipment that generates ozone. Ozone causes
rubber components to deteriorate resulting in reduced performance,
or a limitation or stop of functions.(Excluding items with
measurements against ozone.)
●D
o not use any type of medium that is not specifically stipulated in the
specifications. Using a non-specified medium could lead to short term
loss of function, sudden degradation of performance, and a reduced
operating life.
●W
hen a solenoid valve is installed within the control panel and when
the energizing time is long, implement heat dissipation measures in
order to keep the temperature around the solenoid within
specifications. Also note that continuous energizing for long periods
will result in heat generation by the coil which can lead to deterioration
of solenoid valve performance and shortening of its service life, and
can adversely affect nearby equipment. Contact Koganei if you need
to continuously energize for long periods or if the energizing time in a
day needs to be longer than the deenergizing time.
●A
fter completing wiring work, check to make sure that all connections
are correct before turning on power.
●W
hen using the valve in a manifold, be aware when operating an air
cylinder, or performing air blowing operations, back pressure could cause
erratic operations of the cylinder or erroneous air delivery from the air blow
port. Caution is particularly needed when operating single acting cylinders,
or when operating a cylinder and blowing air from the same manifold.
●D
o not use the product in locations subject to direct sunlight
(ultraviolet radiation), high temperatures or high humidity, dust, salt,
or iron powder. Do not expose the product to fluids or an ambient
atmosphere that contains organic solvents, phosphate-based
hydraulic fluid, sulfur dioxide gas, chlorine gas, acids, etc. It could
lead to early shutdown of some functions, a sudden degradation of
performance, and a reduced operating life. For information about
materials, see Materials of major parts.
注意
●W
hen mounting the product, leave room for adequate working space
around it. Failure to do so will make it more difficult to conduct daily
inspections or maintenance, which could eventually lead to system
shutdown or damage to the product.
●W
henever transporting or installing a heavy product, use a lift or
supports to securely support it, and use several people to help lift it
and take other precautions to ensure personal safety.
● Do not bring any magnetic media or memory media, or other similar
items within one meter of an energized solenoid valve. Doing so creates
the risk of damage to data on the magnetic media due to magnetism.
● If leakage current is flowing in the control circuit, there is a possibility of
the product performing an unintended operation. Take measures against
current leaking in the control circuit, to ensure that the leakage current
value does not exceed the allowed range in the product specifications.
● Do not use a solenoid valve in locations subject to large electrical currents
or strong magnetic fields. Doing so could result in erratic operation.
●O
il from a compressor (except from the oil free compressor) can
greatly reduce product performance and can even cause functional
stoppages. Be sure to install a mist filter before pneumatic equipment
to remove oil.
●T
he properties of the lubrication oil can change when used in dry air
where dew point temperatures is lower than –20°C [–4°F]. It could
result in degraded performance or in functional shutdown.
● While the product is in operation, avoid touching it with your hands or
otherwise approaching too close. Heat generated by the coil can
cause burn injury.
ATTENTION
●W
hen considering the possibility of using this product in situations or
environments not specifically noted in the catalog or instruction
manual, or in applications where safety is an important requirement
such as in aircraft eguipment, combustion equipment, leisure
equipment, safety equipment, and other places where human life or
assets may be greatly affected, take adequate safety precautions
such as allowing plenty of margin for ratings and performance, or failsafe measures. Contact the sales department at Koganei regarding
use in such applications.
●W
hen handling the product, wear protective gloves, safety glasses,
safety shoes, and other protective clothing.
●W
hen the product can no longer be used, or is no longer necessary,
dispose of it appropriately, according to the “Law Regarding the
Disposal and Cleaning of Waste” or other local governmental rules
and regulations, as industrial waste.
●P
neumatic equipment can exhibit degraded performance and function
over its operating life. Always conduct daily inspections of the
pneumatic equipment, and confirm that all requisite system functions
are satisfied, to prevent accidents from happening.
●A
ir leakage of the solenoid valves cannot be cut to zero. Take volume and
holding time requirements into consideration when designing pressure
(including vacuum) retention in the pressure vessel, and other factors.
●A
ir leakage of the solenoid valves cannot be cut to zero. Take volume and
holding time requirements into consideration when designing pressure
(including vacuum) retention in the pressure vessel, and other factors.
Other precautions
● Always observe the following items.
1. When using this product in pneumatic systems, always use
genuine Koganei parts or compatible parts (recommended parts).
When conducting maintenance and repairs, always use genuine
Koganei parts or equivalent parts (recommended parts).
Always observe the prescribed methods and procedures.
2. Never attempt inappropriate disassembly or assembly of the
product relating to basic configurations, or its performance or
functions.
Koganei shall not be held responsible for any problems that occur as a
result of these items not being properly observed.
Warranty and General Disclaimer
1. Warranty Period
Koganei warrants this product for a period of no more
than 180 days from the date of delivery.
2. Scope of Warranty and General Disclaimer
(1) T
he Koganei product warranty covers individual
products. When a product purchased from Koganei or
from an authorized Koganei distributor malfunctions
during the warranty period in a way that is attributable to
Koganei's responsibility, Koganei will repair or replace
the product free of charge. Even if a product is still within
the warranty period, its durability is determined by its
operation cycles and other factors. Contact your nearest
K oganei sales o ffic e or the K oganei o v er sea s
department for details.
(2) Koganei shall not be held responsible for any losses or
for any damage to other machinery caused by
breakdown, loss of function, or loss of performance of
Koganei products.
(3) Koganei shall not be held responsible for any losses
due to use or storage of the product in a way that is
outside of the product specifications prescribed in
Koganei catalogs and the instruction manual, and/or
due to actions that violate the mounting, installation,
adjustment, maintenance and other safety precautions.
(4) Koganei shall not be held responsible for any losses
caused by breakdown of the product due to factors
outside the responsibility of Koganei, including but not
limited to fire, natural disaster, the actions of third
parties, and intentional actions or errors by you.
2
Handling Instructions and Precautions
Manual override
Internal circuit
●24 VDC
Solenoid with LED indicator and surge suppression
Lead wire
(+)
Red
(Red)
Lead wire
(-)
Black
NOTE
1. D
o not apply megger between the pins.
2. M
alfunctions, such as the solenoid valve not returning to normal, may occur
if there is a leakage current within the circuit. Always use it at less than the
allowable leakage current shown in the solenoid specifications. If circuit
conditions, etc. cause the leakage current to exceed the maximum
allowable leakage current, consult us.
3. F
or the double solenoid configuration, avoid energizing both solenoids
simultaneously.
To operate the manual override, press it all the way down.
For the single solenoid, the valve works the same as when in the energized
state as long as the manual override is pushed down, and returns to the rest
position upon release.
For the double solenoid, pressing the manual override on the 14 (SA) side
switches the 14 (SA) to the energized state, and the unit remains in that state
even after the manual override is released. To return it to the rest position,
operate the manual override on the 12 (SB) side. This is the same for the
solenoid 12 (SB).
Attaching and removing plug connector
Use fingers to insert the connector into the pin, push it in until the lever claw
latches onto the protruded section of the connector housing, and complete the
connection.
To remove the connector, squeeze the lever along with the connector, lift the
lever claw up from the protruded section of the connector housing, and pull it out.
Protrusion
Pin
Housing
Lever
Connector assembly
KSB0352Z
Connector
Contact
Crimping of connecting lead wire and contact
To crimp lead wires into contacts, strip off 4 mm [0.16 in] of the insulation from
the end of the lead wire, insert it into the contact, and crimp it. Be sure at this
time to avoid catching the insulation on the exposed wire crimping section.
Exposed wire 4 mm [0.16 in]
Lead wire
Equivalent to AWG#22〜#28
Insulation crimp tab
Hook
NOTE
Exposed wire
crimping section
Insulation (Maximum outer diameter: φ1.7 [0.067])
1. Do not pull hard on the lead wire.
2. Always use a dedicated tool for crimping of connecting lead wire and contact.
Contact:
Crimping tool:
Model 702062-2M
Manufactured by Sumiko Tech, Inc.
Model F1-702062
Manufactured by Sumiko Tech, Inc.
Attaching and removing contact and connector
Insert the contact with lead wire into a plug connector □ hole until the
contact hook latches on and is secured to the plug connector. Confirm
that the lead wire cannot be easily pulled out.
To remove it, insert a tool with a fine tip (such as a small screwdriver)
KSB0353Z
into the rectangular hole
on the side of the plug connector to push up
on the hook, and then pull out the lead wire.
NOTE
1. Do not pull hard on the lead wire. It could result in defective contacts,
breaking wires, etc.
2. If the pin is bent, use a small screwdriver, etc. to gently straighten out the
pin, and then complete the connection to the plug connector.
3
SH
NOTE
1. T
he iB-ZERO series uses pilot type solenoid valves, so if you do not
supply air to the 1 (P) port, the main valve will not change, even if
you operate the manual override.
2. D
o not attempt to operate the manual override with a pin or other
object having an extremely fine tip. It could result in damage to the
manual override.
Identification of quick fitting size
Tube size unit
mm size
in size
Indication of
polarity(DC)
Contact
PU
Release ring color
Ivory
Milk white
Handling Instructions and Precautions
Media
General precautions
Mounting
1. While any mounting direction is allowed, be sure to avoid strong
shocks or vibrations applied directly to the body.
2. Avoid using in the locations and environment listed below, as it
could result in malfunction of the valve. If use in such conditions is
unavoidable, always provide a cover or other adequate protective
measures.
● Location directly exposed to water drops or oil drops
● Environment where a valve body is subject to dew condensation
● Location directly exposed to machining chips, dust, etc
3. In piping connection with valves, flush the tube completely (by
blowing compressed air) before piping.
Intrusion of machining chips or sealing tape, rust, etc., generated
during plumbing could result in air leaks and other defective
operations.
4. Never use the valve with the 4(A) and 2(B) ports vented to the
atmosphere.
5. When mounting a valve inside a control panel, or when energizing
time is long, make adequate consideration for ventilation and other
heat dissipation measures.
6. When adding or subtracting units in the manifold, or replacing a
fitting block, be sure to tighten to within the specified tightening
torque range.
1. Use air for the media. For the use of any other media, consult us.
2. Air used for the cylinder should be clean air that contains no
deteriorated compressor oil, etc. Install an air filter (filtration of 40
µm or less) near the valve to remove collected liquid or dust. In
addition, drain the air filter periodically.
3. When supply pressure is low, use piping for the 1(P) port with
sufficient tube size.
Lubrication
Can be used without lubrication due to the factory lubricant (grease).
When the pneumatic products require lubrication, use Turbine Oil
Class 1 (ISO VG32) or the equivalent. In addition, cutting off oil feed
while an operation is in progress could lead to malfunction due to the
dissipation of the factory lubricant (grease). As a result, always keep
the oil feed running continuously. However, use caution since
excessive oil feed can also be a cause of malfunction. Avoid using
spindle oil or machine oil.
Atmosphere
The product cannot be used when the media or ambient atmosphere
contains any of the substances listed below.
Organic solvents, phosphate ester type hydraulic oil, sulphur dioxide,
chlorine gas, or acids, etc.
Wiring
After wiring, check that there is no error in the wiring connections.
DIN rail mounting brackets
As shown in below images, first make sure that the DIN rail mounting bracket is mounted on both sides of the manifold. Then
securely connect the hooks of both sides to the DIN rail from above, and fix the position with DIN rail mounting screws.
NOTE
When the DIN rail mounting bracket is selected, the maximum is number of valves is 16 stations.
DIN rail mounting screw
Main unit mounting screw
Tightening torque 0.74 N
[0.55 ft・lbf]
DIN rail mounting
bracket
Hooks (both sides)
Fix with DIN rail mounting screw
Tightening torque 0.74 N [0.55 ft・lbf]
(Same for other side)
4
How to assemble and replace valves
Assemble or replace the valves while the manifold body is not fixed.
Refer to ③ and ④ when the customer is the one purchasing the end block and valves and assembling the manifold.
①Remove the mounting screws (bracket attached) from the four places (when adding valves, the two places on the top and bottom of
where you are adding the valve) on the top and bottom of the valve to replace.
Mounting
screw
(bracket
attached)
Gasket-side
Gasket
IBZR8Z-PJ
(Sold separately)
Air supply port
Air supply port
Left side
Intermediate piping block
Right side
Same on
other side
Groove
Mounting screw
(bracket attached)
Exhaust port
(Integrated muffler)
End block
Protrusion
②T
he valve and end block can be removed by opening them diagonally and pulling up.
Open diagonally
Pull up
③Assemble while diagonally aligning the positions of the indents and protrusions of the new valve.
Align the indents
and protrusions
Close
④After attaching, fix it with a mounting screws. (Recommended tightening torque: 0.49 N • m [0.36 ft • lbf])
[Caution]
● Always turn off the power and the air supplies before starting work. Also, be sure to proceed after checking that all air from inside the manifold is
vented.
● The maximum number of units that can be connected in a series is 20, including intermediate piping blocks.
● Be careful that the gasket is not pinched or does not fall out.
● Before supplying air to the manifold, be sure to check that the connections that were made between each valve and end block are secure.
● We recommend adding intermediate piping blocks 「IBZR8Z-PJ（-PJ3/8）」 if needed, when there is a large number of valves or a large number
of valves simultaneously supplying air to the secondary side. Also, be careful of actuator malfunctions caused by the exhaust pressure.
Furthermore, both intermediate piping blocks 「IBZR8Z-PJ（-PJ3/8）」 and valves can be added using the same procedure.
● For muffler exhaust type, before use, confirm that there is no exhaust noise or increase in pressure in the control panel when it is sealed.
● Air leakage from valves is not zero. For questions regarding the allowable amount of leakage, contact our sales office.
[Warranty Period]
● The warranty period for this product is 12 months from the date of delivery. However, failure, loss of performance, or loss of function due to normal
degradation is outside the scope of warranty, even if it is within the warranty period.
5
iB-ZERO
Specifications
Model
Item
IBZR8-4E1
Number of positions
Number of ports
Valve function
Operation system
Flow rate
characteristics
5
Single solenoid
Medium
3
Sonic conductance C
dm /(s·bar)
Effective cross section area [Cv value]
Note 1
2
mm [Cv]
Connection port size
IBZR8-4E2
2 positions
Double solenoid
Air
Internal pilot type
mm
J42：0.8、J62：1.6、J82：2
in
J5/32：0.8、J1/4：1.6、J5/16：2
mm
J42：4〔0.22〕、J62：8〔0.44〕、J82：10〔0.56〕
in
J5/32：4〔0.22〕、J1/4：8〔0.44〕、J5/16：10〔0.56〕
mm
Supply port φ10 [0.394]Note 2, outlet port φ4 [0.157], φ6 [0.236], φ8 [0.315]
in
Lubrication
Supply port 3/8、outlet port 5/32、1/4、5/16
Not required
Operating pressure range
MPa [psi]
Proof pressure
MPa [psi]
Operating temperature range (atmospheric and medium)
℃ [℉]
Response time Note 3 on/off time
ms
Maximum operating frequency
Hz
0.2 to 0.7 [29 to 102]
1.05 [152]
15/30 or less
5 to 50 [41 to 122]
5
m/s2 [G]
Shock resistance
Mounting direction
30 or less
294.2 [30]
Unrestricted
Notes 1: The effective cross section values are calculated values, and are not measured values.
2: Only when the intermediate piping block with quick fitting exhaust port is selected.
3: The valve when air pressure is 0.5 MPa [73 psi].
Electrical Specifications
Rated voltage
Item
Applicable voltage range
Current (when rated voltage applied)
Power consumption
Allowable circuit leakage current
Type of insulation
Insulation resistance Note
Color of LED indicator
Surge protection (standard equipment)
V
mA
W
mA
MΩ
Mass
24 VDC
21.6 to 26.4 (24±10%)
23
0.55
1.0
B type
100 or over
Red
Flywheel diode
Note: Value at 500 VDC Megger
Remark: Specification values are based on Koganei test standards.
g [oz]
Model
IBZR8-4E1
IBZR8-4E2
Mass
mm
J42: 59 [2.08], J62: 60 [2.12], J82: 63 [2.22]
in
J5/32：59[2.08]、J1/4：60[2.12]、J5/16：63[2.22]
mm
J42: 75 [2.65], J62: 75 [2.65], J82: 78 [2.75]
in
J5/32：75[2.65]、J1/4：75[2.65]、J5/16：78 [2.75]
IBZR8Z-E (end block)
81 [2.86]
IBZR8Z-PJ
50 [1.76]
IBZR8Z-EJ
84 [2.96]
IBZR8Z-E3/8
IBZR8Z-PJ3/8
IBZR8Z-E3/8J
IBZR8Z-PJJ
IBZR8Z-PJ3/8J
81 [2.86]
50 [1.76]
84 [2.96]
53 [1.87]
53 [1.87]
6
Order codes
● Single valve unit (The single valve unit cannot be used alone.)
■ Valve specifications
■ Specifications for fittings of pipe ports
-J42：quick fitting for φ4 [0.157] tubes
-J62：quick fitting for φ6 [0.236] tubes
-J82：quick fitting for φ8 [0.315] tubes
-J5/32：quick fitting for 5/32 in. tubes
-J1/4 ：quick fitting for 1/4 in. tubes
-J5/16：quick fitting for 5/16 in. tubes
-4E1: 5-port, 2-position single solenoid
-4E2: 5-port, 2-position double solenoid
Single solenoid
14 (SA)
Double solenoid
14 (SA)
5 (R1)
1 (P)
3 (R2)
4 (A)
2 (B)
4 (A)
2 (B)
■ Wiring specification
L type plug connector L type plug connector L type plug connector
Lead wire 300 mm [11.8 in] Lead wire 1000 mm [39 in] Lead wire 3000 mm [118.1 in]
-PL
5 (R1)
1 (P)
3 (R2)
-PL1
-PL3
L type plug connector
No connector
12 (SB)
-PLN
Model
Valve specifications
IBZR8
-4E1
-4E2
Specifications for fittings of pipe ports
-J42
-J62
-J82
Wiring specification
-PL
-PL1
-PL3
-J5/32
-J1/4
-J5/16
Voltage
-PLN
-CPL Note 1
-CPL1 Note 2
-CPL3 Note 3
24 VDC※
Note 1: Common connector assembly EAZ-PB is attached.
2: Common connector assembly EAZ-PB1 is attached.
3: Common connector assembly EAZ-PB3 is attached.
Remarks: The gasket is installed in the valve body. Two mounting screws (bracket attached) are provided with the valve body.
※ For questions regarding support for 5-V, 6-V, and 12-V DC products, contact our sales office.
●Manifold
■ Specifications for fittings of pipe ports
■ Valve specifications
Left side
■ Manifold format
-J42: quick fitting for φ4 [0.157] tubes -J5/32: quick fitting for 5/32 in. tubes
-4E1: 5-port, 2-position single solenoid
-J62: quick fitting for φ6 [0.236] tubes -J1/4: quick fitting for 1/4 in. tubes
-4E2: 5-port, 2-position double solenoid
-J82: quick fitting for φ8 [0.315] tubes -J5/16: quick fitting for 5/16 in. tubes
-PJ: Intermediate piping block for Φ10 mm tube
-PJ3/8: Intermediate piping block for 3/8 inch tube
■ Wiring specification
-PJJ: Intermediate piping block with quick fitting exhaust
L type plug connector L type plug connector
L type plug connector
L type plug connector
port for Φ10 mm tube
Lead wire 300 mm [11.8 in] Lead wire 1000 mm [39 in] Lead wire 3000 mm [118.1 in] No connector
-PJ3/8J: Intermediate piping block with quick fitting exhaust
Right side
port for 3/8 inch tube
N: Finished product has each
valve connected
■Mounting
(fixed with mounting screw (bracket
Blank: Direct mounting
attached))
-DN: With DIN rail mounting bracket Note 1,Note 3
NS: Semi-finished product
before each valve is
connectedNote 1
*Mounting screws (bracket
attached) must be used to
connect and fix each valve
before use.
(mounting screw (bracket attached)
provided)
Model
-PL
Pre-wired positive
common terminalNote 6
Lead wire 300mm
Blank: Quick fiting for φ10mm tube
-J3/8: Quick fiting for 3/8 inch tube
-J：1 ( P ), 3 ( R ) quick fitting for Φ10 mm tube
-J3/8J ：1 ( P ), 3 ( R ) quick fitting for 3/8 inch tube
Number of valves Manifold format
1
・
・
・
20（16）Note 1
-PL3
Pre-wired positive
common terminalNote 6
Lead wire 1000mm
-PLN
Pre-wired positive
common terminalNote 6
Lead wire 3000mm
■Piping block（End block at right side）
Mounting
Piping block
Stations
-CPL
Model
Manifold model
IBZR8M
-PL1
Valve specifications Specifications for fittings of pipe ports Wiring specification
-CPL3
Voltage
Model of mounted valve
Blank
N
NSNote 2
-CPL1
Blank
-DN
Note 1、
Note 3
-J3/8Note 8
-J
-J3/8JNote 8
stn. 1
・
・
・
stn.□
Note 4
IBZR8
-4E1
-4E2
-PL -CPLNote 6
-J42 -J5/32 Note 8 -PL1 -CPL1
-J62 -J1/4 Note 8 -PL3 -CPL3 DC24VNote 7
-J82 -J5/16 Note 8
-PLNNote 5
(If an intermediate piping block is mounted on the specified station)
-PJ -PJ3/8Note 8 -PJJ -PJ3/8JNote 8
Note 1: Note1: The maximum number of valves is 20 stations. When the DIN rail mounting bracket is selected, the maximum is 16 stations.
2: After doing connections, before supplying air to the manifold, be sure to check that the connections that were made between each valve and end block are secure.
3: Please separately prepare the DIN rail. When -NS is selected for the maniflod format, the DIN rail mounting brackets will be attached parts.
4: Valve positions are counted from the left side of the manifold.
5: Common connector assemblies are available for common wiring connections. For details, see page ③.
6: W
hen connecting common wires between double solenoid valves on the 12 (SB) side, connections are possible between double solenoid valves if 1single solenoid valve is mounted between them, or even if
1 intermediate piping block is mounted between them. However, connections cannot be done if there are two or more, due to the relative length of the branch wires for common connections.
7: For questions regarding support for 5-V, 6-V, and 12-V DC products, contact our sales office.
8: (mm) fitting and (in.) fitting valves cannot be mixed in the same manifold.
7
Order codes
● Additional parts (available separately)
DIN rail mounting bracket
IBZR8Z-DN
IBZR8Z-GS
(4 mounting screws
included)
NOTE
Set of brackets and
mounting screws
Gasket
DIN rail
DIN -
IBZR8Z-KN
DIN-□
（Unit: 1 pcs）
(Units: 2 pcs)
(Units: 1)
When using DIN rail
mounting brackets, the
maximum number of
valves is 16 stations.
End block (left-right set)
Length of DIN rail
125：125mm
150：150mm
175：175mm
200：200mm
225：225mm
250：250mm
275：275mm
300：300mm
Intermediate piping block
IBZR8Z-
A type: EAZ-PA□
IBZR8Z-
1（P）port quick fittings
1（P）port quick fittings
E：quick fitting for φ10 [0.394] tube
PJ：quick fitting for φ10 [0.394] tube
E3/8：quick fitting for 3/8 in. tube
PJ3/8：quick fitting for 3/8 in. tube
B type: EAZ-PB□
(With 1 gasket and 2 connecting
brackets attached)
(With 1 gasket and 2 connecting
brackets attached)
325：325mm
350：350mm
375：375mm
400：400mm
425：425mm
450：450mm
475：475mm
500：500mm
*
Black (−)
Red (+)
*
Red (+) (For common wiring)
Black (−)
*
C type: EAZ-PC□
End block with quick fitting exhaust port (left-right set)
IBZR8Z-
IBZR8Z1
（P）
,3
（P）port quick fittings
EJ：quick fitting for φ10 [0.394] tube
E3/8J：quick fitting for 3/8 in. tube
(With 1 gasket and 2 connecting
brackets attached)
1（P）,3（P）port quick fittings
PJJ：quick fitting for φ10 [0.394] tube
PJ3/8J：quick fitting for 3/8 in. tube
*
example
1.type: EAZ-PB□
the relative length of the branch
B
wires for common wire connections,
Red (+) (For common wiring)
connections cannot be done if two or more
Branch wire
intermediate piping blocks are mounted
Black (−)
between valves.
2. When connecting common wires between
double
solenoid valves on the 12 (SB) side,
C type:
EAZ-PC□
connections are possible between double
Redsolenoid
(+) (For common
solenoid valves if 1 single
valvewiring)
is
mounted between them, or even Black
if 1 (−)
intermediate
Red (+)
A type B type
B type B type B piping
type C typeblock is mounted
between them. However, connections
Lead
300two
mmor[11.8
in]
cannotwire
be length
done if Blank:
there are
more,
1: 1000
mmbranch
[39 in]
due to the relative length
of the
3: 3000 mm [118 in]
wires for common connections.
EAZ -
Connector specification
P : Connector, lead wire length 300 mm [11.8 in]
P1 : Connector, lead wire length 1000 mm [39 in]
P3 : Connector, lead wire length 3000 mm [118 in]
PN : Connector, without lead wire (contacts included)
EAZ-P, P1, P3, PN cannot be wired with the
common connector assembly.
*
Black (−)
Red (+)
Lead wire length Blank: 300 mm [11.8 in]Black (−)
1: 1000 mm [39 in]
3: 3000 mm [118 in]Red (+)
Connection
NOTE
Due to
Common connector assembly
EAZ -
NOTE
A type: EAZ-PA□
(With 1 gasket and 2 connecting
brackets attached)
Connector-related
Red (+) (For common wiring)
Intermediate piping block with quick fitting exhaust port
*
*
Connector specification
PA : Positive common A type, connector, lead wire length 300 mm [11.8 in]
PA1 : Positive common A type, connector, lead wire length 1000 mm [39 in]
PA3 : Positive common A type, connector, lead wire length 3000 mm [118 in]
PB : Positive common B type, connector, lead wire length 300 mm [11.8 in]
PB1 : Positive common B type, connector, lead wire length 1000 mm [39 in]
PB3 : Positive common B type, connector, lead wire length 3000 mm [118 in]
PC : Positive common C type, connector, lead wire length 300 mm [11.8 in]
PC1 : Positive common C type, connector, lead wire length 1000 mm [39 in]
PC3 : Positive common C type, connector, lead wire length 3000 mm [118 in]
CPN : Positive common, connector, without lead wire (short bar and contacts included)
*
Connection example
Branch wire
Lead wire assembly (order made) with completed common connections
Using lead wire assemblies with completed common connections reduces wiring.
Order codes
A type B type B type B type B type C type
EAZ-1W -
P
For the EAZ-1W-6P□
Common wires
Lead wire length
Blank
300 mm [11.8 in]
1
1000 mm [39 in]
3
3000 mm [118 in]
〜
Number of units wired together
2: 2 connections
20: 20 connections
Lead wire assembly with completed common connections
NOTE
Common wires
Black Red Black Black Black Black Black Red
(-) (+) (-)
(-)
(-)
(-)
(-) (+)
Branch wire (red)
1. D
ue to the relative length of the branch wires for
common wire connections, connections cannot
be done if two or more intermediate piping
blocks are mounted between valves.
2. W
hen connecting common wires between
double solenoid valves on the 12 (SB) side,
connections are possible between double
solenoid valves if 1 single solenoid valve is
mounted between them, or even if 1 intermediate
piping block is mounted between them.
However, connections cannot be done if there
are two or more, due to the relative length of the
branch wires for common connections.
8
Dimensions
mm [in]
■ Single valve unit (With quick fittings for mm tubes)
35 [1.378]
IBZR8-4E2-J□-PL
5-port single solenoid
15 [0.591]
(300 [11.8])
10 [0.394]
30 [1.181]
10.5
[0.413]
Manual override
2 (B) port
131.6 [5.18]
82 [3.228]
4 (A) port
2 (B) port
Fitting
-J42: φ4 [0.157]
-J62: φ6 [0.236]
-J82: φ8 [0.315]
-J42: (2.6 [0.102])
-J62: (3 [0.118])
-J82: (4.7 [0.185])
15 [0.591] (300 [11.8])
10 [0.394]
4 (A) port
15
[0.591]
28.3
[1.114]
102 [4.016]
77.2 [3.039]
Manual override
5-port double solenoid
35 [1.378]
30 [1.181]
10.5
[0.413]
15
[0.591]
IBZR8-4E1-J□-PL
-J42: (2.6 [0.102])
-J62: (3 [0.118])
-J82: (4.7 [0.185])
Fitting
-J42: φ4 [0.157]
-J62: φ6 [0.236]
-J82: φ8 [0.315]
2 mounting screws provided
2 mounting screws provided
Exhaust port (Integrated muffler)
20 [0.787]
1P
72.3 [2.846]
20 [0.787]
■Intermediate piping block with quick fitting
exhaust port (Single unit)
IBZR8Z-PJJ（With quick fittings for mm tubes）
72.3 [2.846]
■ Intermediate piping block (single unit)
IBZR8Z-PJ（With quick fittings for mm tubes）
(Same position on other side)
9
(5.3 [0.209])
2 mounting screws provided
35 [1.378]
Exhaust port
(Integrated muffler)
35 [1.378]
(5.3 [0.209])
3R
2 mounting screws provided
Dimensions
mm [in]
■ Manifold
IBZR8M□N (With quick fittings for mm tubes)
Unit dimensions
Number of units
L
4.5 [0.177]
LED indicator
P
22.5 15 [0.591] Manual override 17.5
[0.886] (pitch)
[0.689]
4 (A) port
2 (B) port
4.5 [0.177]
15 [0.591]
(300 [11.8])
30 [1.181]
4-φ4.2 [0.165] (Oval hole)
(Mounting hole)
1 (P) port
3
85 [3.346] 76 [2.992]
15 [0.591]
5
Fitting
(φ6 [0.236])
25 [0.984]
(5.3 [0.209])
stn. 1 stn. 2 stn. 3 stn. 4
15 [0.591]
13
[Mounting example]
IBZRM4N
stn.1 IBZR8-4E1-J42-PL 24 VDC
stn.2 IBZR8-4E1-J62-PL 24 VDC
stn.3 IBZR8-4E1-J82-PL 24 VDC
stn.4 IBZR8-4E2-J82-PL 24 VDC
106 [4.2]
145 [5.7]
136 [5.4]
160 [6.3]
12
Mounting screw
115 [4.5]
8
7
11
Fitting (φ8 [0.315])
100 [3.9] 91 [3.583]
130 [5.1]
10
35.8 [1.409]
28.3 [1.114]
Fitting
(φ4 [0.157])
70 [2.756] 61 [2.402]
6
14
4.9 [0.193]
62 [2.441]
55 [2.165] 46 [1.811]
2
4
Exhaust port
(Integrated muffler)
PNote
1
9
6 [0.236]
72.3 [2.846]
35.3 [1.39]
-J42: (2.6 [0.102])
-J62: (3.0 [0.118])
-J82: (4.7 [0.185]) 5.2 [0.205]
102 [4.016]
77.2 [3.039]
131.6 [5.18]
Fitting (φ10 [0.394])
10.8 [0.425]
LNote
175 [6.9]
190 [7.5]
205 [8.1]
220 [8.7]
235 [9.3]
250 [9.8]
121 [4.8]
151 [5.9]
166 [6.5]
181 [7.1]
196 [7.7]
211 [8.3]
226 [8.9]
241 [9.5]
15
265 [10.4] 256 [10.1]
17
295 [11.6] 286 [11.3]
16
280 [11] 271 [10.7]
18
310 [12.2] 301 [11.9]
20
340 [13.4]
19
325 [12.8] 316 [12.4]
331 [13]
Note:I f intermediate piping
blocks are mounted, add
20 mm [0.787 in] for each
of the intermediate piping
blocks in L and P.
If intermediate piping block is mounted
(Model: IBZR8-PJ)
20 [0.787] Exhaust port (Integrated muffler)
Intermediate piping block
1 (P) port
Fitting (φ10 [0.394])
Exhaust port (Integrated muffler)
(Same position on other side)
10
Dimensions
mm [in]
■Manifold (With DIN rail mounting bracket)
IBZR8M□N-DN (With quick fitting for mm tubes)
Q
12 [0.472]
ＬＥＤ indicator
L
22.5 15 [0.591] Manual override 17.5
[0.886] （Pitch）
[0.689]
30
[1.181]
10.8
[0.425]
Exhaust port
(Integrated muffler)
１
（Ｐ）
Port
47 [1.850]
28.3 [1.114] 15 [0.591]
72.3 [2.846]
2
35.8 [1.409]
6
7
8
9
10
11
Mounting screw
12
ｓ
ｔ
ｎ．
１ｓ
ｔ
ｎ．
２ｓ
ｔ
ｎ．
３ｓ
ｔ
ｎ．
４
25
[0.984]
（7.5）
[0.295]
35.3 [1.390]
15 [0.591]
（5.3）
[0.209]
4.9 [0.193]
12.7 [0.500]
1
3
Fitting（φ８ [0.315]）
Fitting
Fitting
（φ4 [0.157]） （φ6[0.236]）
DIN rail mounting bracket
(Attached when NS is selected)
35
［1.378］
5.5
［0.217］
25
［0.984］
20.5
［0.807］
DIN rail mounting hole dimension
If intermediate piping block is mounted
(Model: IBZR8-PJ)
20 [0.787] Exhaust port (Integrated muffler)
1 (P) port
Fitting (φ10 [0.394])
Exhaust port (Integrated muffler)
(Same position on other side)
13
14
15
LNote
55[2.165]
70[2.756]
Q Note
79[3.110]
94[3.701]
85[3.347] 109[4.291]
100[3.937] 124[4.882]
115[4.528] 139[5.472]
130[5.118] 154[6.063]
145[5.709] 169[6.654]
160[6.299] 184[7.244]
175[6.890] 199[7.835]
190[7.480] 214[8.425]
205[8.071] 229[9.016]
220[8.661] 244[9.606]
235[9.252] 259[10.197]
250[9.843] 274[10.787]
265[10.433] 289[11.378]
16
280[11.023] 304[11.969]
Note:If intermediate piping blocks
are mounted, add 20 mm
[0.787 in] for each of the
[Mounting example]
intermediate piping blocks in
IBZR8M4N-DN
L and P.
stn.1 IBZR8-4E1-J42-PL DC24V
stn.2 IBZR8-4E1-J62-PL DC24V
stn.3 IBZR8-4E1-J82-PL DC24V
stn.4 IBZR8-4E2-J82-PL DC24V
（12.5）
［0.492］
Intermediate piping block
Number of units
5
-J42: (2.6 [0.102])
-J62: (3.0 [0.118])
-J82: (4.7 [0.185])
DIN-□
Unit dimensions
4
■DIN rail
11
(300)
[11.8]
Fitting（φ１０ [0.394]）
77.2 [3.039]
131.6 [5.18]
102 [4.016]
４
（Ａ）
Port
２
（Ｂ）
Port
15 [0.591]
mm [in]
■Manifold (Exhaust from quick fitting)
IBZR8M□N-J
(With quick fitting for mm tubes)
-J
Unit dimensions
L
4.5[0.177]
ＬＥＤ indicator
22.5
[0.886]
15 [0.591]
（Pitch）
Number of units
4.5[0.177]
P
Manual override
(300 [11.8])
16.5
16
[0.650] [0.630]
４
（Ａ）
Port
30 [1.181]
10.8 [0.425]
4-φ4.2 [0.165] (Oval hole)
(Mounting hole)
1 (P) port
２
（Ｂ）
Port
23.4 [0.921] 17.5 [0.689]
15 [0.591]
62 [2.441]
28.3 [1.114]
3R
4
Fitting（φ6[0.236]）
15 [0.591]
6 [0.236]
ｓ
ｔ
ｎ.3;IBZR8-4E1-J82-ＰＬ DC24V
ｓ
ｔ
ｎ.4;IBZR8-4E2-J82-ＰＬ DC24V
76[2.992]
91[3.583]
136[5.354]
9
175[6.890]
8
130[5.118]
160[6.299]
190[7.480]
205[8.071]
220[8.661]
121[4.764]
151[5.945]
166[6.535]
181[7.126]
196[7.717]
211[8.307]
235[9.252]
226[8.898]
15
265[10.433]
256[10.079]
17
295[11.614]
286[11.260]
16
IBZR8M4N-J
IBZR8M4N-J
stn.1 IBZR8-4E1-J42-PL DC24V
ｓ
ｔ
ｎ.1;IBZR8-4E1-J42-Ｐ
Ｌ DC24V
stn.2
IBZR8-4E1-J62-PL
DC24V
stn.3
IBZR8-4E1-J82-PL
DC24V
ｓ
ｔ
ｎ.2;IBZR8-4E1-J62-Ｐ
Ｌ DC24V
stn.4 IBZR8-4E2-J82-PL DC24V
85[3.347]
100[3.937]
46[1.811]
61[2.402]
145[5.709]
13
[Mounting
example]
搭載例
70[2.756]
7
6
250[9.843]
280[11.023]
18
310[12.205]
20
340[13.386]
19
25 [0.984]
55[2.165]
P Note
106[4.173]
12
Mounting screw
LNote
115[3.937]
11
Fitting（φ８ [0.315]）
(5.3 [0.209])
-J42: (2.6 [0.102])
-J62: (3.0 [0.118])
-J82: (4.7 [0.185])
3
10
ｓ
ｔ
ｎ.1 ｓ
ｔ
ｎ.2 ｓ
ｔ
ｎ.3 ｓ
ｔ
ｎ.4
35.3 [1.39]
2
14
4.9 [0.193]
72.3 [2.846]
1P
5.2 [0.205]
102 [4.016]
77.2 [3.039]
1 (P) port
Fitting（φ4 [0.157]）
1
5
Fitting (2-φ10 [0.394])
325[12.795]
241[9.488]
271[10.670]
301[11.850]
316[12.441]
331[13.031]
Note:If intermediate piping blocks are mounted, add 20 mm [0.787 in] for each of the
intermediate piping blocks in L and P.
*When NS, NS-DN is selected, this must
be connect by the customer before usage.
For NS, the connecting brackets, for NSDN the the connecting brackets and DIN rail
mounting brackets will be attached.
*When –DN is selected, available stations will
be from 1 to 16 stations.
When the intermediate piping block with
quick fitting exhaust port is installed.
（Model：IBZR8-PJJ）
連数別寸法一覧表20 [0.787]
1 (P) port
17.5
[0.689]
Fitting(2-φ10 [0.394]）
連数 L寸法（注２） P寸法（注２） 注１）
NS、NS-DNを選択した場合は、
ご使用前にお客様にて連結してください。
1
55
46
NSの場合は連結金具が、NS-DNの場合は連結金具、
2
70
61
DINレール取付金具が添付されています。
3
85
76
注２）
中間配管ブロックを搭載した場合は、
Ｌ、
Ｐ寸法に
4
100
91
中間配管ブロックの数量×２０ｍｍを加算してください。
5
115
106
注3）
-DN選択の場合、連数は1〜16連とする。
6
130
121
3(R) port
7
145 block 136
Intermediate
piping
with
8
160 port 151
quick fitting
exhaust
9
175
166
10
190
181
11
205
196
12
220
211
13
235
226
14
250
241
15
265
256
16
280
271
17
295
286
18
310
301
19
325
316
20
340
331
23.4
[0.921]
131.6 [5.18]
R8M
Dimensions
1P
3R
12
mm [in]
形式
■Manifold (With DIN rail mounting bracket,Exhaust from quick fitting)
IBZR8M
-DN-J
IBZR8M□N-DN-J (With quick fitting for mm tubes)
Unit dimensions
Q
12 [0.472]
Number of units
LNote
1
55[2.165]
L
ＬＥＤ indicator
22.5
[0.886]
15 [0.591]
（Pitch）
Manual override
16.5
[0.650]
16
[0.630]
４
（Ａ）
Port
(300)
[11.8]
30 [1.181]
10.8
[0.425]
2
3
１
（Ｐ）
Port
２
（Ｂ）
Port
3R
Fitting
（φ4 [0.157]）
35.3 [1.390]
IBZR8M4N-DN-J
IBZR8M4N-DN-J
stn.1 IBZR8-4E1-J42-PL DC24V
ｓ
ｔ
ｎ.1;IBZR8-4E1-J42-ＰＬ DC24V
stn.2
IBZR8-4E1-J62-PL DC24V
ｓ
ｔ
ｎ.2;IBZR8-4E1-J62-Ｐ
Ｌ DC24V
stn.3
IBZR8-4E1-J82-PL
DC24V
stn.4
IBZR8-4E2-J82-PL
DC24V
ｓ
ｔ
ｎ.3;IBZR8-4E1-J82-Ｐ
Ｌ DC24V
（7.5）
[0.295]
1P
3R
154[6.063]
175[6.890]
199[7.835]
15
[Mounting
搭載例 example]
139[5.472]
9
14
DIN rail mounting bracket
(Attached when NS is selected)
109[4.291]
124[4.882]
169[6.654]
13
ｓ
ｔ
ｎ.4;IBZR8-4E2-J82-ＰＬ DC24V
（注２）
Q寸法
79
When the intermediate piping block with
94
109
quick fitting exhaust port is installed.
124
（Model：IBZR8-PJJ）
139
154
1 (P) port
20 [0.787]
169
184
Fitting(2-φ10 [0.394]）
199
214
229
244
259
注１）
NSを選択した場合は、
ご使用前にお客様にて連結してください。
連結金具、DINレール取付金具は添付されています。
274
注２）
中間配管ブロックを搭載した場合は、L、Q寸法に
289
中間配管ブロックの数量×２０ｍｍを加算してください。
304
3(R) port
Intermediate piping block with
quick fitting exhaust port
17.5
[0.689]
25
[0.984]
（5.3）
[0.209]
-J42: (2.6 [0.102])
-J62: (3.0 [0.118])
-J82: (4.7 [0.185])
15 [0.591]
79[3.110
94[3.701]
145[5.709]
12
Mounting screw
115[3.937]
P Note
7
16
連数別寸法一覧表
13
130[5.118]
11
ｓ
ｔ
ｎ.1 ｓ
ｔ
ｎ.2 ｓ
ｔ
ｎ.3 ｓ
ｔ
ｎ.4
（注２）
L寸法
55
70
85
100
115
130
145
160
175
190
205
220
235
250
265
280
6
10
Fitting（φ８ [0.315]）
Fitting
（φ6[0.236]）
85[3.347]
100[3.937]
8
23.4 [0.921] 17.5 [0.690]
47 [1.850]
28.3 [1.114] 15 [0.591]
4.9 [0.193]
72.3 [2.846]
1P
12.7 [0.500]
102 [4.016]
77.2 [3.039]
131.6 [5.18]
3(R)Port
70[2.756]
4
5
Fitting（2-φ１０ [0.394]）
23.4
[0.921]
数
Dimensions
160[6.299]
190[7.480]
205[8.071]
220[8.661]
235[9.252]
250[9.843]
265[10.433]
280[11.023]
184[7.244]
214[8.425]
229[9.016]
244[9.606]
259[10.197]
274[10.787]
289[11.378]
304[11.969]
Note:If intermediate piping blocks are
mounted, add 20 mm [0.787
in] for each of the intermediate
piping blocks in L and P.
*When NS, NS-DN is selected,
this must be connect by the
customer before usage.For NS, the
connecting brackets, for NS-DN
the the connecting brackets and
DIN rail mounting brackets will be
attached.
*When –DN is selected, available
stations will be from 1 to 16 stations.
Dimensions
mm [in]
■Single valve unit (With quick fittings for inch tubes)
35 [1.378]
IBZR8-4E2-J□-PL
5-port single solenoid
15 [0.591]
(300 [11.8])
10 [0.394]
30 [1.181]
10.5
[0.413]
Manual override
2 (B) port
131.6 [5.18]
82 [3.228]
4 (A) port
2 (B) port
Fitting
-J42: φ4 [0.157]
-J62: φ6 [0.236]
-J82: φ8 [0.315]
-J42: (2.6 [0.102])
-J62: (3 [0.118])
-J82: (4.7 [0.185])
15 [0.591] (300 [11.8])
10 [0.394]
4 (A) port
15
[0.591]
28.3
[1.114]
102 [4.016]
77.2 [3.039]
Manual override
5-port double solenoid
35 [1.378]
30 [1.181]
10.5
[0.413]
15
[0.591]
IBZR8-4E1-J□-PL
-J42: (2.6 [0.102])
-J62: (3 [0.118])
-J82: (4.7 [0.185])
Fitting
-J42: φ4 [0.157]
-J62: φ6 [0.236]
-J82: φ8 [0.315]
2 mounting screws provided
2 mounting screws provided
■ Intermediate piping block (single unit)
■Intermediate piping block with quick fitting
IBZR8Z-PJ3/8（With quick fittings for inch tubes） exhaust port (Single unit)
IBZR8Z-PJ3/8J（With quick fittings for inch tubes）
20 [0.787]
1P
72.3 [2.846]
Exhaust port (Integrated muffler)
72.3 [2.846]
20 [0.787]
(Same position on other side)
(5.3 [0.209])
2 mounting screws provided
35 [1.378]
Exhaust port
(Integrated muffler)
35 [1.378]
(5.3 [0.209])
3R
2 mounting screws provided
14
Dimensions
mm [in]
■Manifold
IBZR8M□N-J3/8 (With quick fittings for inch tubes)
4.5 [0.177]
ＬＥＤ indicator
L
P
22.5 15 [0.591] Manual override 17.5
[0.886] （Pitch）
[0.689]
４
（Ａ）
Port
２
（Ｂ）
Port
4.5 [0.177]
15 [0.591]
Unit dimensions
Number of units
(300) [11.8]
30 [1.181]
4-φ4.2 [0.165] (Oval hole)
(Mounting hole)
1 (P) port
Exhaust port
(Integrated muffler)
3
4
5
35.8 [1.409]
25 [0.984]
(Model: IBZR8-PJ3/8)
20 [0.787] Exhaust port (Integrated muffler)
1 (P) port
Fitting (φ10 [0.394])
Exhaust port (Integrated muffler)
(Same position on other side)
IBZR8M4N-J3/8
stn.1 IBZR8-4E1-J5/32-PL DC24V
stn.2 IBZR8-4E1-J1/4-PL DC24V
stn.3 IBZR8-4E1-J5/16-PL DC24V
stn.4 IBZR8-4E2-J5/16-PL DC24V
76 [2.992]
91 [3.583]
145 [5.709]
136 [5.354]
9
175 [6.890]
12
[Mounting example]
85 [3.346]
100 [3.937]
46 [1.811]
61 [2.402]
7
6
13
130 [5.118]
160 [6.299]
190 [7.480]
205 [8.071]
220 [8.661]
121 [4.764]
151 [5.945]
166 [6.535]
181 [7.126]
196 [7.717]
211 [8.307]
235 [9.252]
226 [8.898]
15
265 [10.433]
256 [10.079]
17
295 [11.614]
286 [11.260]
14
16
(5.3) [0.209]
15 [0.591]
70 [2.756]
106 [4.173]
11
Mounting screw
55 [2.165]
P Note
115 [4.528]
10
Fitting（5/16）
If intermediate piping block is mounted
15
2
15 [0.591]
62 [2.441]
4.9 [0.193]
Fitting
（1/4）
6 [0.236]
35.3 [1.39]
-J5/32: (2.6) [0.102]
-J1/4: (3.4) [0.134]
-J5/16: (4.7) [0.185]
Fitting
（5/32）
stn. 1 stn. 2 stn. 3 stn. 4
Intermediate piping block
1
8
28.3 [1.114]
72.3 [2.846]
5.2 [0.205]
77.2 [3.039]
131.6 [5.18]
102 [4.016]
Fitting（3/8）
10.8 [0.425]
LNote
250 [9.843]
280 [11.024]
18
310 [12.205]
20
340 [13.386]
19
325 [12.795]
241 [9.488]
271 [10.669]
301 [11.850]
316 [12.441]
331 [13.031]
Note:If intermediate piping blocks are mounted,
add 20 mm [0.787 in] for each of the intermediate piping blocks in L and P.
Dimensions
mm [in]
■Manifold (With DIN rail mounting bracket)
IBZR8M□N-DN-J3/8 (With quick fittings for inch tubes)
Q
L
12
ＬＥＤ indicator ［0.472］ 22.5 15［0.591］ Manual override 17.5
15
［0.689］［0.591］
［0.886］（Pitch）
10.8［0.425］
１
（Ｐ）
Port
35.8［1.409］
Exhaust port
(Integrated muffler)
Fitting
（5/16）
Fitting
（1/4）
Mounting screw
ｓ
ｔ
ｎ．
１ｓ
ｔ
ｎ．
２ｓ
ｔ
ｎ．
３ｓ
ｔ
ｎ．
４
Number
of units
LNote
Q Note
1
55 [2.165]
79 [3.110]
2
70 [2.756]
94 [3.701]
3
85 [3.346]
109 [4.291]
4
100 [3.937]
124 [4.882]
5
115 [4.528]
139 [5.472]
6
130 [5.118]
154 [6.063]
7
145 [5.709]
169 [6.654]
8
160 [6.299]
184 [7.244]
9
175 [6.890]
199 [7.835]
10
190 [7.480]
214 [8.425]
11
205 [8.071]
229 [9.016]
12
220 [8.661]
244 [9.606]
13
235 [9.252] 259 [10.197]
14
250 [9.843] 274 [10.787]
16 280 [11.024] 304 [11.969]
25
[0.984]
DIN rail mounting bracket
(Attached when NS is selected)
[Mounting example]
Note:If intermediate piping blocks are
mounted, add 20 mm [0.787 in]
for each of the intermediate piping
blocks in L and P.
IBZR8M4N-DN-J3/8
stn.1 IBZR8-4E1-J5/32-PL DC24V
stn.2 IBZR8-4E1-J1/4-PL DC24V
stn.3 IBZR8-4E1-J5/16-PL DC24V
stn.4 IBZR8-4E2-J5/16-PL DC24V
（7.5）
［0.295］
15［0.591］
Unit dimensions
15 265 [10.433] 289 [11.378]
（5.3）
[0.209]
47
［1.85］
72.3
［2.246］
28.3 15
［1.114］
［0.591］
4.9［0.193］
Fitting
（5/32）
-J5/32：
（2.6）
［0.102］
-J1/4：
（3.4）
［0.134］
（4.7）
［0.185］
35.3［1.39］ -J5/16：
12.7［0.5］
102
［4.016］
30［1.181］
Fitting
（3/8）
77.2
［3.039］
131.6
［5.18］
４
（Ａ）
Port
２
（Ｂ）
Port
（300）
［11.811］
■DIN rail
DIN-□
35
［1.378］
25
［0.984］
5.5
［0.217］
（12.5）
［0.492］
20.5
［0.807］
DIN rail mounting hole dimension
If intermediate piping block is mounted
(Model: IBZR8-PJ3/8)
20 [0.787] Exhaust port (Integrated muffler)
Intermediate piping block
1 (P) port
Fitting (φ10 [0.394])
Exhaust port (Integrated muffler)
(Same position on other side)
16
Dimensions
mm [in]
形式
■Manifold
(Exhaust from quick fitting)
-J3/8J quick fittings for inch tubes)
IBZR8M
IBZR8M□N-J3/8J(With
L
4.5［0.177］
ＬＥＤ indicator
(4.5)［0.177］
P
15［0.591］
22.5
［0.886］ （Pitch）
Manual override
16.5
16
［0.650］ ［0.630］
４
（Ａ）
Port
（300）
［11.811］
4-φ4.2 [0.165] (Oval hole)
(Mounting hole)
1
30［1.181］
10.8
［0.425］
１
（Ｐ）
Port
２
（Ｂ）
Port
Fitting
（5/32）
2
5
(5.3)［0.209］
-J5/32：
（2.6）
［0.102］
-J1/4：
（3.4）
［0.134］
-J5/16：
（4.7）
［0.185］
ｓ
ｔ
ｎ.1;IBZR8-4E1-J42-ＰＬ DC24V
ｓ
ｔ
ｎ.2;IBZR8-4E1-J62-ＰＬ DC24V
6［0.236］
35.3［1.39］
搭載例
ｓ
ｔ
ｎ.3;IBZR8-4E1-J82-ＰＬ DC24V
ｓ
ｔ
ｎ.4;IBZR8-4E2-J82-ＰＬ DC24V
[Mounting example]
IBZR8M4N-J3/8J
stn.1 IBZR8-4E1-J5/32-PL DC24V
stn.2 IBZR8-4E1-J1/4-PL DC24V
stn.3 IBZR8-4E1-J5/16-PL DC24V
stn.4 IBZR8-4E2-J5/16-PL DC24V
連数別寸法一覧表
17.5
[0.689]
（注２） P寸法
（注２）
L寸法
55
46
70
61
85
76
100
91
115
106
When
the intermediate piping block with
130
121
quick fitting exhaust port is installed.
145
136
160
151
（Model：IBZR8-PJ3/8J）
175
166
190
181
1 (P) port
205
196
20 [0.787]
220
211
Fitting(2-3/8）
注１）
NS、
NS-DNを選択した場合は、
ご使用前にお客様にて連結
してください。
235
226
NSの場合は連結金具が、
NS-DNの場合は連結金具、DINレール取付金具が添付されています。
250
241
注２）
中間配管ブロックを搭載した場合は、
Ｌ、
Ｐ寸法に
中間配管ブロックの数量×２０ｍｍを加算してください。
265
256
注3）
-DN選択の場合、連数は1〜16連とする。
280
271
1P
295
286
310
301
325
316
3R
340
331
23.4
[0.921]
連数
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Intermediate piping block with
quick fitting exhaust port
17
3(R) port
91 [3.583]
9
175 [6.890]
10
130 [5.118]
160 [6.299]
190 [7.480]
205 [8.071]
220 [8.661]
121 [4.764]
151 [5.945]
166 [6.535]
181 [7.126]
196 [7.717]
211 [8.307]
235 [9.252]
226 [8.898]
15
265 [10.433]
256 [10.079]
17
295 [11.614]
286 [11.260]
14
IBZR8M4N-J3/8J
76 [2.992]
136 [5.354]
13
25［0.984］
85 [3.346]
100 [3.937]
46 [1.811]
61 [2.402]
145 [5.709]
12
15［0.591］
70 [2.756]
7
11
ｓ
ｔ
ｎ.1 ｓ
ｔ
ｎ.2 ｓ
ｔ
ｎ.3 ｓ
ｔ
ｎ.4
55 [2.165]
P Note
106 [4.173]
8
Mounting screw
LNote
115 [4.528]
6
Fitting
（5/16）
Fitting
（1/4）
1
4
23.4［0.921］ 17.5［0.689］
15
［0.591］
62
［2.441］
28.3［1.114］
3R
Number of units
3
1P
4.9
72.3
［2.246］
5.2
102
［4.016］
3(R)Port
77.2
［3.039］
131.6
［5.18］
Fitting(2-3/8）
Unit dimensions
16
250 [9.843]
280 [11.024]
18
310 [12.205]
20
340 [13.386]
19
325 [12.795]
241 [9.488]
271 [10.669]
301 [11.850]
316 [12.441]
331 [13.031]
Note:If intermediate piping blocks are mounted,
add 20 mm [0.787 in] for each of the intermediate piping blocks in L and P.
*When NS, NS-DN is selected, this must
be connect by the customer before usage.
For NS, the connecting brackets, for NSDN the the connecting brackets and DIN rail
mounting brackets will be attached.
*When –DN is selected, available stations will
be from 1 to 16 stations.
Dimensions
mm [in]
■Manifold
(With DIN rail mounting bracket,Exhaust from quick fitting)
形式
IBZR8M□N-DN-J3/8J
(With quick fittings for inch tubes)
-DN-J3/8J
IBZR8M
Q
ＬＥＤ indicator
12
［0.472］
Unit dimensions
L
22.5［0.886］ 15［0.591］
Manual override
（Pitch）
４
（Ａ）
Port
10.8
［0.425］
3
Fitting
（1/4）
(5.3)［0.209］
-J5/32：
（2.6）
［0.102］
-J1/4：
（3.4）
［0.134］
-J5/16：
（4.7）
［0.185］
35.3［1.39］
154 [6.063]
169 [6.654]
184 [7.244]
205 [8.071]
229 [9.016]
14
[Mounting
example]
搭載例
139 [5.472]
11
13
DIN rail mounting bracket
(Attached when NS is selected)
160 [6.299]
109 [4.291]
124 [4.882]
199 [7.835]
16
25［0.984］
145 [5.709]
79 [3.110]
94 [3.701]
175 [6.890]
15
15［0.591］
115 [4.528]
Q Note
9
12
ｓ
ｔ
ｎ.1 ｓ
ｔ
ｎ.2 ｓ
ｔ
ｎ.3 ｓ
ｔ
ｎ.4
85 [3.346]
130 [5.118]
10
Mounting screw
70 [2.756]
6
8
Fitting
（5/16）
55 [2.165]
100 [3.937]
7
23.4［0.921］ 17.5［0.689］
47
［1.850］
28.3
15
［1.114］ ［0.591］
4.9
［0.193］
72.3
［2.246］
12.7［0.500］
3R
LNote
4
5
3(R)Port
1P
Fitting
（5/32）
Number
of units
1
2
Fitting(2-3/8）
77.2
［3.039］
102
［4.016］
30［1.181］
1(P)Port
２
（Ｂ）
Port
131.6
［5.18］
（300）
［11.811］
16.5
16
［0.650］ ［0.630］
190 [7.480]
220 [8.661]
214 [8.425]
244 [9.606]
235 [9.252]
259 [10.197]
265 [10.433]
289 [11.378]
250 [9.843]
280 [11.024]
274 [10.787]
304 [11.969]
Note:If intermediate piping blocks are
mounted, add 20 mm [0.787 in]
for each of the intermediate piping
blocks in L and P.
IBZR8M4N-DN-J3/8J
IBZR8M4N-DN-J3/8J
stn.1 IBZR8-4E1-J5/32-PL DC24V
ｓ
ｔ
ｎ.1;IBZR8-4E1-J42-Ｐ
Ｌ DC24V DC24V
stn.2
IBZR8-4E1-J1/4-PL
ｓ
ｔ
ｎ.2;IBZR8-4E1-J62-Ｐ
Ｌ DC24V DC24V
stn.3
IBZR8-4E1-J5/16-PL
stn.4
IBZR8-4E2-J5/16-PL
ｓ
ｔ
ｎ.3;IBZR8-4E1-J82-Ｐ
Ｌ DC24V DC24V
（7.5）
［0.295］
ｓ
ｔ
ｎ.4;IBZR8-4E2-J82-ＰＬ DC24V
連数別寸法一覧表
（注２）
Q寸法
79
94When the intermediate piping block with
109
124 quick fitting exhaust port is installed.
139
（Model：IBZR8-PJ3/8J）
154
注１）
NSを選択した場合は、
ご使用前にお客様にて連結してください。
169
連結金具、DINレール取付金具は添付さ
れています。
1 (P)
port
20 [0.787]
184
注２）
中間配管ブロックを搭載した場合は、L、Q寸法に
中間配管ブロックの数量×２０ｍｍを加算してください。
199
Fitting(2-3/8）
214
229
244
259
1P
274
289
304
3R
17.5
[0.689]
（注２）
L寸法
55
70
85
100
115
130
145
160
175
190
205
220
235
250
265
280
23.4
[0.921]
連数
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Intermediate piping block with
quick fitting exhaust port
3(R) port
18
Limited Warranty
KOGANEI CORP. warrants its products to be free from defects
in material and workmanship subject to the following provisions.
Warranty Period The warranty period is 180 days from the date
of delivery.
Koganei
Responsibility
Limitations
If a defect in material or workmanship is found
during the warranty period, KOGANEI CORP.
will replace any part proved defective under
normal use free of charge and will provide the
service necessary to replace such a part.
•
This warranty is in lieu of all other warranties,
expressed or implied, and is limited to the
original cost of the product and shall not
include any transportation fee, the cost of
installation or any liability for direct, indirect
or consequential damage or delay resulting
from the defects.
•
•
•
•
URL http://www.koganei.co.jp
E-mail: [email protected]
OVERSEAS DEPARTMENT
3-11-28, Midori-cho, Koganei City, Tokyo 184-8533, Japan
Tel: 81-42-383-7271 Fax: 81-42-383-7276
KOGANEI INTERNATIONAL AMERICA, INC.
39300 Civic Center Dr., Suite 280, Fremont, CA 94538, U.S.A.
Tel : 1-510-744-1626 Fax : 1-510-744-1676
SHANGHAI KOGANEI INTERNATIONAL TRADING CORPORATION
Room 2606-2607, Tongda Venture Building No.1, Lane 600, Tianshan Road,
Shanghai, 200051, China
Tel: 86-21-6145-7313 Fax: 86-21-6145-7323
TAIWAN KOGANEI TRADING CO., LTD.
Rm. 2, 13F., No88, Sec. 2, Zhongxiao E. Rd., Zhongzheng Dist., Taipei City 100,
Taiwan (ROC)
Tel: 886-2-2393-2717 Fax: 886-2-2393-2719
KOGANEI KOREA CO., LTD.
6F-601, Tower Bldg., 1005, Yeongdeo-dong, Giheung-gu, Yongin-si, Gyeonggi-do,
446-908, Korea
Tel: 82-31-246-0414 Fax: 82-31-246-0415
KOGANEI (THAILAND) CO., LTD.
3300/90, Tower B, Elephant Tower,16th Fl., Phaholyothin Road, Chomphon,
Chatuchak, Bangkok 10900, Thailand
Tel: 66-2-937-4250 Fax: 66-2-937-4254
KOGANEI ASIA PTE. LTD.
69 Ubi Road 1, #05-18 Oxley Bizhub, Singapore 408731
Tel: 65-6293-4512 Fax: 65-6293-4513
12/’19 KG
©KOGANEI CORP. PRINTED IN JAPAN
KOGANEI CORP. shall in no way be liable or responsible for
injuries or damage to persons or property arising out of the
use or operation of the manufacturer’s product.
This warranty shall be void if the engineered safety devices
are removed, made inoperative or not periodically checked for
proper functioning.
Any operation beyond the rated capacity, any improper use or
application, or any improper installation of the product, or any
substitution upon it with parts not furnished or approved by
KOGANEI CORP., shall void this warranty.
This warranty covers only such items supplied by KOGANEI
CORP. The products of other manufacturers are covered only by
such warranties made by those original manufacturers, even
though such items may have been included as the components.
The specifications are subject to change without notice.
">