Acura | Music Link | BII31183-31898 RL Acura Music Link.pmd

Accessory
INSTALLATION
INSTRUCTIONS
PARTS LIST
Attachment Kit (sold separately)
P/N 08A28-1H1-800
Application
Publications No.
BII 31183-31898
ACURA MUSIC LINK
(FOR I-POD®)
2006 RL
Issue Date
FEB 2006
Music Link Adapter Kit (sold separately)
P/N 08A28-1H2-100
Music Link adapter unit
4 Cushion tapes
Bus cable
Holder cushion
Music Link harness
Grommet
CD-ROM
8 Wire ties
2 Long wire ties
Quick reference guide
Bus Cable 2 Port (sold separately)
P/N 08A31-0F1-000
Bus cable 2 port
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
BII 31183-31898 (0602)
08B28-SJA-2000-91
1 of 9
3.
TOOLS AND SUPPLIES REQUIRED
#2 Phillips screwdriver
Flat-tip screwdriver
Diagonal cutters
Remove the three clips from the glove box under
cover, and pull the glove box under cover out
toward you to remove the two pins.
PINS (2)
Scissors
Ratchet
10 mm Socket
10 mm Combination wrench
Drill motor
Drill bit (3 mm)
Hole saw (20 mm)
Shop towel
Pushpin
Eye protection
CLIPS (3)
Isoproply alcohol
Electrical tape
Illustration of the Music Link System Installed on
the Vehicle
MUSIC LINK
BUS CABLE
GLOVE BOX
UNDER COVER
VEHICLE
CONNECTOR
4.
Remove the glove box under cover by unplugging
5531010B
the vehicle connector.
5.
Open the glove box, and remove the cover as
shown.
ADAPTER
UNIT
AUDIO
UNIT
WASHER
BOLT
COVER
SELF-TAPPING
SCREWS (4)
MUSIC
LINK
HARNESS
WASHER
BOLT
GLOVE
BOX
WASHER
BOLT
5531020B
5530160B
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
2.
Disconnect the negative cable from the battery.
2 of 9
BII 31183-31898 (0602)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
6.
Remove the four self-tapping screws and four
washer bolts.
7.
Pull down the glove box to remove the two clips
and release the two retaining tabs.
ILLUMINATION
BULB
10. Open the pocket lid, and remove the inner case.
VEHICLE
CLIP
11. Remove the center console trim (four clips, the
clip that secures the vehicle harness, and
disconnect the vehicle connectors). The number
of the vehicle connectors varies depending on the
type of vehicle.
RETAINING
TAB
CLIPS (4)
CENTER
CONSOLE TRIM
VEHICLE
CONNECTOR
GLOVE
BOX
CLIPS (2)
GLOVE
BOX
VEHICLE
CONNECTOR
8.
9.
4312043T
5531030B
CLIP
Remove the glove box by removing the vehicle
clip, illumination bulb and unplugging the vehicle
connector.
With the parking brake applied, place the gear
shift lever in the neutral position.
12. Remove the two self-tapping screws from the
pocket.
13. Pry out the pocket, then remove the illumination
bulb by twisting from the rear of the pocket. The
illumination harness is short; take care not to pull
it excessively. Remove the pocket.
POCKET
POCKET LID
BACK SIDE of
POCKET
INNER CASE
SELF-TAPPING
SCREW
GEAR SHIFT
(Neutral position)
ILLUMINATION
BULB
4312021T
4312032T
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
BII 31183-31898 (0602)
3 of 9
14. Open the console lid. Pull the console trim out
toward you to remove the two clips, then remove
the console trim.
CONSOLE
LID
CONSOLE
TRIM
CLIPS (4)
CLIPS (2)
17. Using the same procedure, remove the driver's
seat side console trim.
18. Remove the console mat from inside the console
box.
WASHER
BOLTS (8)
CONSOLE
MAT
CUP
HOLDER
15. Pull the cup holder out toward you to remove the
four clips, then remove the cup holder.
5531050B
16. Remove the seven clips of the passenger's seat
side console trim. Pull the passenger's seat side
console trim toward the rear to remove the two
pins, then remove the trim.
Pull the center
console toward
the rear.
CENTER
CONSOLE
5531060B
FRONT
19. Remove the eight washer bolts from the center
console, and pull the center console toward the
rear.
PIN
20. Remove the right center panel trim by removing
the three clips and the one retaining tab.
PIN
CLIPS (6)
PASSENGER'S
SEAT SIDE
CONSOLE
TRIM
RETAINING
TAB
CLIPS (7)
5531040B
RETAINING
TAB
LEFT CENTER
PANEL TRIM
RIGHT CENTER
PANEL TRIM
4 of 9
BII 31183-31898 (0602)
4312010T
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
21. Using the same procedure, remove the left center
panel trim.
24. Remove the center module by unplugging the
vehicle connectors.
22. Remove the inner trim (two self-tapping screws).
25. Route the DIN connector end of the bus cable
from the center module opening to the glove box
opening.
INNER
TRIM
DIN
CONNECTOR
GLOVE BOX
OPENING
BUS
CABLE
SELF-TAPPING
SCREW
5627060B
23. Pull the center module out toward you to remove
the two flange bolts and four washer bolts from the
center module.
CENTER MODULE
OPENING
VEHICLE
CONNECTOR
5530050B
26. Connect the bus cable 14-pin connector and the
vehicle 14-pin connector to the bus cable 2 port
14-pin connectors.
CENTER
MODULE
14-PIN
CONNECTORS (2)
•Align
BUS
CABLE
CUSHION
TAPES (2)
FLANGE
BOLTS (2)
WASHER
BOLTS (4)
BUS CABLE
2 PORT
5531071B
VEHICLE 14-PIN
CONNECTOR OR
BUS CABLE 14-PIN
CONNECTOR
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
BII 31183-31898 (0602)
5512040B
5 of 9
27. Attach the two cushon tapes to the bus cable 2
port 14-pin connectors you just connected.
28. Align the bus cable 2 port 14-pin connector with
the vehicle 20-pin connector, and secure the bus
cable 2 port and the bus cable to the vehicle
harness with two wire ties as shown.
WIRE
TIE
30. To prevent damage, wrap electrical tape around
the drill bit at a point about 30 mm away from the
tip. While wearing eye protection, drill a 20 mm
hole through the marked location. Remove all
burrs from the drilled hole.
DRILL
BIT
30 mm
VEHICLE
HARNESS
ELECTRICAL
TAPE
DRILL
MOTOR
BUS CABLE
2 PORT
PUSHPIN
BUS
CABLE
WIRE
TIE
3 mm
DRILL BIT
20 mm
HOLE SAW
GLOVE
BOX
20 mm
5530061B
BUS CABLE
VEHICLE 20-PIN
(Align.) 2 PORT 14-PIN
CONNECTOR
CONNECTOR
20 mm
5530101B
29. Using a felt-tip pen, mark the Music Link harness
as shown.
31. Route the Music Link harness DIN connector into
the 20 mm hole in the direction shown.
FELT-TIP
PEN
20 mm
HOLE
MUSIC
LINK
HARNESS
MUSIC LINK
HARNESS
DIN CONNECTOR
750 mm
MARK
MUSIC
LINK
HARNESS
5627070B
GLOVE
BOX
5530111B
6 of 9
BII 31183-31898 (0602)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
32. Cut the grommet as shown. Attach the grommet
to the Music Link harness, and seat the grommet
into the 20 mm hole.
UTILITY
KNIFE
20 mm
HOLE
34. Insert the Music Link adapter unit into the unit
cushion.
UNIT
CUSHION
GROMMET
MUSIC LINK
ADAPTER
UNIT
MUSIC
LINK
HARNESS
(Align ends.)
GLOVE
BOX
GROMMET
5627080B
33. Clean the vehicle pipe and vehicle bracket with
isopropyl alcohol where the cushion tapes will
attach. Attach a cushion tape to the vehicle pipe.
CUSHION
TAPE
5426010B
35. Route the Music Link harness through the glove
box opening and connect the Music Link harness
DIN connector (White) to the Music Link adapter
assembly. Note the location of the connector and
the terminals.
36. Secure the Music Link harness to the vehicle pipe
with the two wire ties.
VEHICLE
PIPE
WIRE
TIE
VEHICLE
PIPE
MUSIC
LINK
HARNESS
5627090B
GLOVE
BOX
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
BII 31183-31898 (0602)
MUSIC LINK
ADAPTER
ASSEMBLY
MUSIC LINK
HARNESS
DIN CONNECTOR
(WHITE)
5627100B
7 of 9
37. Temporarily secure the Music Link adapter
assembly to the vehicle pipe with two long wire
ties.
VEHICLE
PIPE
39. Secure the two long wire ties.
40. Bundle up the excess bus cable, and secure them
to the vehicle harness with two wire ties.
MUSIC LINK
ADAPTER
ASSEMBLY
GLOVE BOX
OPENING
FRONT
VEHICLE
PIPE
GLOVE BOX
OPENING
SIDE VIEW
MUSIC LINK
HARNESS
(Bundle up the
excess.)
LONG WIRE
TIE
MUSIC LINK
ADAPTER
ASSEMBLY
5627110B
VEHICLE
HARNESS
5627130B
41. Bundle up the excess Music Link harness, and
secure them to the vehicle harness with two wire
ties (Align the mark you made in step 29 with the
wire tie as shown).
38. Route the bus cable through the two long wire ties
temporarily secured in step 37, and connect the
bus cable DIN connector (Black) to the Music Link
adapter assembly. Note the location of the
connector and the terminals.
MUSIC LINK
ADAPTER
ASSEMBLY
WIRE
TIE
Align the mark you
made in step 29 with
the long wire tie.
VEHICLE
HARNESS
LONG WIRE
TIE
MUSIC
LINK
HARNESS
VEHICLE
HARNESS
BUS CABLE
DIN CONNECTOR
(BLACK)
MUSIC LINK
HARNESS
(Bundle up the
excess.)
WIRE
TIE
WIRE
TIE
ILLUMINATION
BULB
5627140B
5627120B
8 of 9
BII 31183-31898 (0602)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
42. Reinstall the glove box.
43. Connect the vehicle connectors and bus cable 14pin connector (or bus cable 2 port 14-pin
connector) to the center module, and reinstall the
center module.
VEHICLE
CLIP
ILLUMINATION
BULB
RETAINING
TAB
VEHICLE
CONNECTOR
CENTER
MODULE
GLOVE
BOX
CLIPS (2)
BUS CABLE 14-PIN
CONNECTOR or
BUS CABLE 2 PORT
14-PIN CONNECTOR
GLOVE
BOX
5530151B
VEHICLE
CONNECTOR
WASHER
BOLT
FLANGE
BOLTS (2)
WASHER
BOLTS (4)
5530131B
COVER
44. Check that all wire harnesses are routed properly
and all connectors are plugged in.
SELF-TAPPING
SCREWS (4)
45. Reconnect the negative cable to the battery.
46. Enter the customer’s radio anti-theft code, and
reset the radio station presets, the clock.
47. Reinstall all removed parts.
48. Turn the audio unit ON. Check that "No Disc" is
shown on the display while in the CD changer
mode (the Music Link should be recognized as CD
changer 4).
NOTE: Whenever the battery is disconnected, the
driver’s AUTO function is disable.
WASHER
BOLT
GLOVE
BOX
49. Start the engine. Push down on the driver’s
window switch until the window is fully open.
WASHER
BOLT
5530140B
50. Pull up on the driver’s window switch fully to close
the window completely, then hold the switch for
2 seconds or more.
51. Test the window AUTO function.
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
BII 31183-31898 (0602)
9 of 9
Download PDF