Philips | 39PFL3708 | Technical data | Philips 39PFL3708 Technical data

Hudson 7
20.1" LCD Monitor
Service
Service
Service
200WP7EB/00
200WP7ES/00
200WP7ES/01
Horizontal frequencies
30 - 98 KHz
TABLE OF CONTENTS
Description
Page
Important Safety Notice----------------------------------2
Technical Data------------------------------------------3~4«
Connection to PC------------------------------------------5
On-screen Display(OSD) ---------------------------- 6~9
Safety Test Requirement-------------------------------10
Aging Mode/OSD Lock/unlock ------------------------11
Factory Mode---------------------------------------------12
Definition of pixel defects ------------------------------13
Panel Failure Mode--------------------------------------14
Trouble Shooting------------------------------------15~16
Mechanical Instructions ---------------------------17~18
Display Adjustments -------------------------------19~20
DDC Instructions & DDC Data--------------------21~28
Firmware Upgrade for CPU----------------------- 29~30
Description
Page
Electrical Instructions------------------------------ 31~32
Repair Tips------------------------------------------- 33~34
Repair Flow Chart----------------------------------- 35~37
Function Block Diagram---------------------------------38
Scaler Schematic Diagram & C.B.A(for */00) --39~46
Power Schematic Diagram & C.B.A--------------47~50
USB Diagram & C.B.A ------------------------------51~53
Control Schematic Diagram & C.B.A------------ 54~55
Exploded View------------------------------------------ --56
General Product Specification --------------------57~81
Recommended/Spare parts list-------------------82~86
Different Parts List ---------------------------------------87
Scaler Schematic Diagram & C.B.A(for */01) --88~95
Updated Parts---------------------------------------------96
Revision List-----------------------------------------------97
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Published by BCU Monitors
Printed in Suzhou
Copyright reserved
Subject to modification F
Jun. 02 2006
GB 3138 106 10504
2
200WP7 LCD
Important Safety Notice
Go to cover page
Proper service and repair is important to the safe,
reliable operation of all Philips Consumer Electronics
Company** Equipment. The service procedures
recommended by Philips and described in this service
manual are effective methods of performing service
operations. Some of these service operations require
the use of tools specially designed for the purpose. The
special tools should be used when and as
recommended.
It is important to note that this manual contains
various CAUTIONS and NOTICES which should be
carefully read in order to minimize the risk of personal
injury to service personnel. The possibility exists that
improper service methods may damage the equipment.
It is also important to understand that these
CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
Philips could not possibly know, evaluate and advise
the service trade of all conceivable ways in which
service might be done or of the possible hazardous
consequences of each way. Consequently, Philips has
not undertaken any such broad evaluation. Accordingly,
a servicer who uses a service procedure or tool which
is not recommended by Philips must first satisfy
himself thoroughly that neither his safety nor the safe
operation of the equipment will be jeopardized by the
service method selected.
TO ENSURE THE CONTINUED RELIABILITY OF THIS
PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH
THEIR PART NUMBERS IN THE PARTS LIST SECTION
OF THIS SERVICE MANUAL.
Take care during handling the LCD module with
Backlight unit
- Must mount the module using mounting holes
arranged in four corners.
- Do not press on the panel, edge of the frame
strongly or electric shock as this will result in
damage to the screen.
- Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in
damage to the panel.
- Protect the module from the ESD as it may damage
the electronic circuit (C-MOS).
- Make certain that treatment person s body are
grounded through wrist band.
- Do not leave the module in high temperature and in
areas of high humidity for a long time.
- Avoid contact with water as it may a short circuit
within the module.
- If the surface of panel become dirty, please wipe it
off with a soft material. (Cleaning with a dirty or
rough cloth may damage the panel.)
* *Hereafter throughout this manual, Philips Consumer
Electronics Company will be referred to as Philips.
WARNING
FOR PRODUCTS CONTAINING LASER :
Critical components having special safety
characteristics are identified with a
by the Ref. No.
in the parts list and enclosed within a broken line*
(where several critical components are grouped in one
area) along with the safety symbol
on the
schematics or exploded views.
Use of substitute replacement parts which do not have
the same specified safety characteristics may create
shock, fire, or other hazards.
Under no circumstances should the original design be
modified or altered without written permission from
Philips. Philips assumes no liability, express or implied,
arising out of any unauthorized modification of design.
Servicer assumes all liability.
* Broken Line
DANGER- Invisible laser radiation when open.
AVOID DIRECT EXPOSURE TO BEAM.
CAUTION- Use of controls or adjustments or
performance of procedures other than
those specified herein may result in
hazardous radiation exposure.
CAUTION- The use of optical instruments with this
product will increase eye hazard.
Technical Data
ELECTRICAL SPECIFICATION
1.
1.1.
1.2
General
Product description
The Hudson 7, 20.1" WSXGA TFT flat panel monitor is specified
as a display peripheral with Analog video signal input, Digital
video input 20.1" TFT LCD display.
Horizontal scan range is 30 - 98K Hz and refresh range is
56 - 76 Hz. This scan range allows it to display resolution up to
1680*1050 non-interlaced at 60 Hz refresh rate. The image
can be adjust through OSD control, these adjustments can be
stored on an board memory including 40 preset modes
and 15 factory preset modes.
All optical characteristics (including WHITE-D, Brightness, and
so on) are determined according to panel specification after
warming up approximate 30 minutes that brightness stability is
optimal, and follows strictly after panel specification
Destination:
1.3. Basic data
1.3.1 LCD panel
Type NR.
: M201EW01 V0 (AUO)
Outside dimensions
: 459.4(H)*296.4(V)*22.8(D) (Typ) mm
Pixel Pitch ( mm )
: 0.258 mm x 0258mm
Color pixel arrangement : RGB vertical stripes
Display surface
: low reflection, antiglare with hard coating
Color depth
: 16.7M colors (8 bits)
Backlight
: Six CCFL' s
Active area(WxH)
: 433.44x270.9mm (20.1" W diagonal)
View angle
: Horizontal 176& Vertical 176 degree (CR>=10)
Contrast ratio
: 800:1 (Typ) ,400 :1 (min)
White luminance
: Panel original color >240nits (min), 300 nits (Typ.)
1.3.2.
Power supply
Main voltage : AC 90 - 135 Vrms and 170 - 264 Vrms, 50/60±2 Hz
Power cord length : 1.8M
Power cord type
: 3 lead with earth plug
Power indicator : LED (ON: green, Standby: amber, NEW MODE: flashing
Green twice per second before user adjusts and save it).
Auto power saving : EPA, Nutek, VESA DPMS
Mode
HSYNC
VSYNC
Video
Pwr-cons.
Indication
Rec.
time
Power-On
On
On
active
< 60 W
Green
< 48W
LED
w/o USB
Off
Off
On
blanked
< 2.0 W
Amber
<3s
LED
Off
On
Off
blanked
< 2.0 W
Amber
<3s
LED
Off
Off
Off
blanked
< 2.0 W
Amber
<3s
LED
DC Power
N/A
< 1.0 W
LED Off
Off
1.3.3. Horizontal scan
: 30 - 98 KHz
1.3.4. Vertical scan
: 56 - 76 Hz
1.3.5. Input signals
1.Signal input level
Video : 0.7 Vp-p Linear / 75 ohms
Sync : H/H+V, V TTL level, composite sync, sync on green
Impedance
Video : Terminated with 75 ohms
Sync : Terminated with 2K2 ohms
The input signals can be applied in two different modes:
3
200WP7 LCD
Go to cover page
1). VESA Analog
Input signal: Video, Hsync., Vsync
Video: 0.7 Vp-p, input impedance, 75 ohms @DC
Sync. : Separate sync
TTL level, input impedance 5k ohms
Hor. sync
Positive/Negative
Ver. sync
Positive/Negative
2).
Intel DVI Digital
Input signal: Four channel TMDS signals
1.3.6 Input connectors
(1) Input analog D-sub connector pin assignment
PIN No.
SIGNAL
1
Red
2
Green/ SOG
3
Blue
4
Sense (GND)
5
NC
6
Red GND
7
Green GND
8
Blue GND
9
DDC +5V
10
Cable detect (GND)
11
Sense (GND)
12
Bi-directional data
13
H/H+V sync
14
V-sync
15
Data clock
(2) Input DVI-D connector pin assignment
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Description
TMDS data2TMDS data2+
TMDS data2/4 shield
NC
NC
DDC clock
DDC data
NC
TMDS data1TMDS data1+
TMDS data1/3 shield
NC
NC
+5V
Ground (return for +5V and H/Vsync)
Hot plug detect
TMDS data0TMDS data0+
TMDS data0/5 shield
NC
NC
TMDS clock shield
TMDS clock+
TMDS clock-
4
Technical Data
200WP7 LCD
Go to cover page
Signal interface
-
15Pins, D-sub male with DDC2B Pin assignments
24Pins, DVI-D male with DDC2B Pin assignments
Sync polarity:
-Hori.sync
-Vert.sync
positive/negative
positive/negative
1.3.7. Controls:
Front side:
- DC power switch
- OSD function key (OK)
- UP
- DOWN
- RIGHT
- LEFT
- AUTO
Rear:
- D-SUB
- DVI-D
- Power cord socket
Connection to PC
5
200WP7 LCD
Go to cover page
Installing Your LCD Monitor
Front View Product Description
1
2
3
4
5
6 AUTO
To switch monitor's power On and Off
To access OSD menu
To adjust the OSD
To adjust brightness of the display
To adjust the OSD
Automatically adjust the horizontal position,
vertical position, phase and clock setting
Rear View
Connect the cables to the back of your computer by following these
steps:
(a)Turn off your computer and unplug its power cord.
(b)Connect the monitor signal cable to the video connector on the back
of your computer
(c)Plug the power cord on your computer and your monitor into a nearby
outlet.
(d)USB plug
(1)
Connect USB upstream port on monitor and the USB port on PC
with a USB cable.
(2)
The USB downstream port is now ready for any USB device to
plug in
(e)Turn on your computer and monitor. If the monitor displays an image,
1 AC power input
2 DVI-I input
3 D-SUB Input
4 Kensington anti-thief lock
5 USB upstream and downstream
Connect to PC
Connect the power cord and DVI cable to the back of the monitor firmly.
(Philips has pre-connected VGA cable for the first installation.)
installation is complete.
Note: The USB plug is a pass through connection whether it can
support USB 1.1 or USB 2.0 depends on your PC's specification
6
On Screen Display
200WP7 LCD
Go to cover page
Description of the On Screen Display
What is the On-Screen Display?
This is a feature in all Philips LCD monitors. It allows an end user to
adjust screen performance of the monitors directly through an on-screen
instruction window. The user interface provides user-friendliness and
ease-of-use when operating the monitor.
Basic and simple instruction on the control keys.
When you press the
button on the front control of your monitor,
the On-Screen Display (OSD) Main Controls window will pop up and
you can then start making adjustments to your monitor's various
features. Use the
or the
keys to make your adjustments
The OSD Tree
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work
your way around the different adjustments later on.
On Screen Display
7
200WP7 LCD
Go to cover page
8
200WP7 LCD
Go to cover page
On Screen Display
On Screen Display
9
200WP7 LCD
Go to cover page
10
200WP7 LCD
Go to cover page
All units that are returned for service or repair must pass the
original manufactures safety tests. Safety testing requires both
Hipot and Ground Continuity testing.
HI-POT TEST INSTRUCTION
1.Application requirements
1.1 All mains operated products must pass the Hi-Pot test as
described in this instruction.
1.2 This test must be performed again after the covers have
been refitted following the repair, inspection or modification
of the product.
2. Test method
3. Equipments and Connection
3.1. Equipments
For example :
- ChenHwa 9032 PROGRAMMABLE AUTO SAFETY
TESTER
- ChenHwa 510B Digital Grounding Continuity Tester
- ChenHwa 901 (AC Hi-pot test), 902 (AC, DC Hi-pot test)
Withstanding Tester
3.2. Connection
* Turn on the power switch of monitor before Hipot and
Ground Continuity testing.
Clip
2.1 Connecting conditions
2.1.1 The test specified must be applied between the parallelblade plug of the mainscord and all accessible metal
parts of the product.
2.1.2 Before carrying out the test, reliable conductive
connections must be ensured and thereafter be
maintained throughout the test period.
2.1.3 The mains switch(es) must be in the "ON" position.
Clip
2.2 Test Requirements
All products should be HiPot and Ground Continuity tested as
follows:
Condition
HiPot Test for
products where
the mains input
range is Full
range(or 220V
AC)
HiPot Test for
Ground Continuity
products where
Test requirement
the mains input is
110V AC(USA
type)
Test
voltage
2820VDC
(2000VAC)
1700VDC
(1200VAC)
Test time 3 seconds
(min.)
1 second
Trip
current
(Tester)
5 mA
Ramp
time
(Tester)
set at 100 uA
for Max.
limitation; set
at 0.1 uA for
Min. Limitation
set at 2
seconds
Test current:
25A,AC
Test time:
3 seconds(min.)
Resistance
required:
<=0.09+Rohm,
R is the
resistance of
the mains cord.
(ChenHwa 9032 tester)
Video cable
Connect the "video cable"
or "grounding screw"
to the CLIP on your tester.
Grounding screw
2.2.1 The minimum test duration for Quality Control Inspector
must be 1 minute.
2.2.2 The test voltage must be maintained within the specified
voltage + 5%.
Connect the power cord
to the monitor.
2.2.3 There must be no breakdown during the test.
2.2.4 The grounding blade or pin of mains plug must be
conducted with accessible metal parts.
Power outlet
4. Recording
(Rear view of monitor)
Hipot and Ground Continuity testing records have to be kept
for a period of 10 years.
11
200WP7 LCD
Go to cover page
Front View
WAIT FOR AUTOMATIC ADJUSTMENT
This screen appears when you press the "AUTO" buttons at the same
time. It will disappear when the monitor is properly adjusted
ATTENTION SIGNAL
WAITING FOR AUTOMATIC ADJUSTMENT
Access Aging.. Mode
Step 1 : Turn off LCD monitor, and disconnect Interface Cable
between Monitor and PC.
Step 2 : [Push "
"&"
" buttons at the same time and
hold it]+[Press power "
" button until comes out " AGING screen"
] => then release all buttons.
Bring up:
AGING...
To Lock/Unlock OSD FUNCTION(User Mode)
The OSD function can be locked by pressing"OK"button for more
than 10 seconds, the screen shows following windows for 3 seconds.
Everytime when you press"AUTO" or "OK" button, this message appears on the screen automatically.
After 15 seconds, bring up:
ATTENTION SIGNAL
OSD MAIN CONTROLS LOCKED
After 15 seconds, bring up:
AGING...
Unlock OSD function
After 15 seconds, bring up:
Locked OSD function can be released by pressing "OK" button for more
than 10 seconds again
ATTENTION SIGNAL
OSD MAIN CONTROLS UNLOCKED
NO VIDEO INPUT
This screen appears if there is no video signal input. Please check that
the signal is properly connected to the video card of PC and make sure
PC is on
ATTENTION SIGNAL
CHECK CABLE CONNECTION
------------------repeatly
Connect Signal cable again=> go back to normal display
12
200WP7 LCD
Go to cover page
Front Control Panel
Access Factory Mode
How to get into Factory Mode Menu
Step1:
Turn off monitor.
Step2:
[Push "
"& "
" buttons at the same time and hold it]
+[Press power "
" button untill comes out "Windows screen" ]
=> then release all buttons
Step3:
Press OK "
" button, bring up Factory mode indication as shown
in Fig2.
Factory Mode indicator
13
200WP7 LCD
Go to cover page
Philips' Flat Panel Monitors Pixel Defect Policy
Black Dot Defects
Philips strives to deliver the highest quality products. We use some of
the industry's most advanced manufacturing processes and practice
stringent quality control. However, pixel or subpixel defects on the TFT
LCD panels used in flat panel monitors are sometimes unavoidable.
No manufacturer can guarantee that all panels will be free from pixel
defects, but Philips guarantees that any monitor with an unacceptable
number of defects will be repaired or replaced under warranty.
This notice explains the different types of pixel defects and defines
acceptable defect levels for each type. In order to qualify for repair or
replacement under warranty, the number of pixel defects on a TFT LCD
panel must exceed these acceptable levels.
For example, no more than 0.0004% of the subpixels on a 15" XGA
monitor may be defective. Furthermore, Philips sets even higher quality
standards for certain types or combinations of pixel defects that are
more noticeable than others. This policy is valid worldwide .
Black dot defects appear as pixels or subpixels that are always dark or
"off".
These are the types of black dot defects:
One dark subpixel
Two or three adjacent dark subpixels
Proximity of Pixel Defects
Because pixel and subpixels defects of the same type that are nearby
one another may be more noticeable, Philips also specifies tolerances
for the proximity of pixel defects.
Pixel Defect Tolerances
In order to qualify for repair or replacement due to pixel defects during
the warranty period, a TFT LCD panel in a Philips flat panel monitor
must have pixel or subpixel defects exceeding the tolerances listed in
the following tables.
Pixels and Subpixels
A pixel, or picture element, is composed of three subpixels in the
primary colors of red, green and blue. Many pixels together form an
image. When all subpixels of a pixel are lit, the three colored subpixels
together appear as a single white pixel. When all are dark, the three
colored subpixels together appear as a single black pixel.
Other combinations of lit and dark subpixels appear as single pixels of
other colors.
Types of Pixel Defects
Pixel and subpixel defects appear on the screen in different ways.
There are two categories of pixel defects and several types of subpixel
defects within each category.
Bright Dot Defects Bright dot defects appear as pixels or subpixels that
are always lit or "on".
These are the types of bright dot defects:
One lit red, green or blue subpixel
Note:
Two adjacent lit subpixels:
- Red + Blue = Purple
- Red + Green = Yellow
- Green + Blue = Cyan (Light Blue)
Three adjacent lit subpixels
(one white pixel)
* 1 or 2 adjacent sub pixel defects = 1 dot defect
Your Philips monitor is ISO13406-2 Compliant
14
Failure Mode Of Panel
200WP7 LCD
Go to cover page
Quick reference for failure mode of LCD panel
this page presents problems that could be made by LCD panel.
It is not necessary to repair circuit board. Simply follow the mechanical
instruction on this manual to eliminate failure by replace LCD panel.
Failure description
Vertical block defect
Polarizer has bubbles
Phenomenon
Polarizer has bubbles
Vertical dim lines
Foreign material inside
polarizer. It shows liner or
dot shape.
Vertical lines defect
(Always bright or dark)
Concentric circle formed
Horizontal block defect
Bottom back light of LCD is
brighter than normal
Horizontal dim lines
Back light un-uniformity
Horizontal lines defect
(Always bright or dark)
Has bright or dark pixel
Backlight has foreign material.
Black or white color, liner or
circular type
Troubleshooting
200WP7 LCD
15
Go to cover page
This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these
solutions, contact Philips customer service representative.
Common Problems
Having this problem
No Picture
Check these items
·
Make sure the power cord is plugged into the
power outlet and into the back of the monitor.
(Power LED not lit)
·
First, ensure that the power button on the front
of the monitor is in the OFF position, then
press it to the ON position.
No Picture
·
Make sure the computer is turned on.
·
Make sure the signal cable is properly
(Power LED is amber or yellow)
connected to your computer.
·
Check to see if the monitor cable has bent
pins.
Screen says
·
The Energy Saving feature may be activated
·
Make sure the monitor cable is properly
connected to your computer. (Also refer to the
Quick Set-Up Guide).
·
Check to see if the monitor cable has bent
pins.
AUTO button not working properly
·
Make sure the computer is turned on.
·
The Auto Function is designed for use on
standard Macintosh or IBM-compatible PCs
running Microsoft Windows.
·
It may not work properly if using nonstandard
PC or video card.
Imaging Problems
Display position is incorrect
·
Press the Auto button.
·
Adjust
the
image
position
using
the
Phase/Clock of More Settings in OSD Main
Controls.
Image vibrates on the screen
Check that the signal cable is properly connected to the
graphics board or PC
200WP7 LCD
16
Troubleshooting
Go to cover page
Vertical flicker appears
·
Press the Auto button.
·
Eliminate
the
vertical
bars
using
the
Phase/Clock of More Settings in OSD Main
Controls.
Horizontal flicker appears
·
Press the Auto button.
·
Eliminate
the
vertical
bars
using
the
Phase/Clock of More Settings in OSD Main
Controls.
The screen is too bright or too dark
·
Adjust the contrast and brightness on Monitor
Setup. (The backlight of the LCD monitor has a
fixed life span. When the screen becomes dark
or begins to flicker, please contact your
dealer).
An after-image appears
·
If an image remains on the screen for an
extended period of time, it may be imprinted in
the screen and leave an after-image. This
usually disappears after a few hours
An after-image remains after the power has been turned
off.
·
This is characteristic of liquid crystal and is not
caused by a malfunction or deterioration of the
liquid crystal. The after-image will disappear
after a peroid of time.
Green, red, blue, dark, and white dots remains
The remaining dots are normal characteristic of the liquid
crystal used in today’s technology
For further assistance, refer to the Consumer Information Centers list and contact Philips customer service
representative
Mechanical Instructions
17
200WP7 LCD
Go to cover page
1.Back view as Fig.1
Fig.1
Fig.6
2.remove the base
- Step 1: Place the monitor face down on a smooth surface as Fig 2.
Be carefully to prevent the scratch and injury during the uninstallation.
3. Remove cable base as Fig7 and Fig.8
Unscrew the screws
Fig.7
Fig.8
Fig.2
4.Remove back cover as Fig.9 and Fig.10
Fig.9
Step 2: Unfasten one screw on the base stand as Fig 3.
Fig.3
Unscrew the 2 screws and open the clicks on the sides
Fig.10
Step 3: Firmly insert the base removal tool into four-pronged clicks as Fig 4
Fig.4
5.Remove the shielding
-Unscrew the screws and then pull down the shielding as Fig.11 Fig.12
Step 4: Pull out the foot from base as Fig 5 Fig.6.
Fig.12
Fig.5
Base Column
Base stand
18
200WP7 LCD
Mechanical Instructions
Go to cover page
Fig.11
Fig.15
6.Remove the power board and scaler board
-unscrew the screws and disconnect the connectors as Fig.13,Fig.14
8. Remove the control board
-unscrew the screws and disconnect the connector as Fig.16
Fig.16
Fig.13
Fig.14
7.Reomve the USB board
-Disconnect the connector and unscrew the screws as shown in Fig.15
Display Adjustment
200WP7 LCD
19
Go to cover page
TO access factory mode
1. Turn off monitor(do not turn off PC)
2. Press AUTO , OK and the power simultaneously on the frond control
panel, then press OK wait till the OSD menu come on the screen of
monitor.
2. Apply a 1280x1024/60Hz signal with white pattern.Set
brightness control at 100% and contrast control at 50%. Adjust
the R.G.B gain to reach special color temperature on center of screen.
2.1 Aim the probe CA-A30 at the center of screen as Fig. 4
2.2 Remove the lens protective cover of probe CA-A30.
2.3 Set Measuring/viewing selector to Measuring position for reset
analyzer. (Zero calibration) as Fig. 5
2.4 Turn on the colour analyzer (CA-110).
2.5 Press 0-CAL button to start reset analyzer. See Fig. 6
Fig.1
3.If OSD menu disappears on the screen of monitor. press OK
again(anytime), then the OSD menu comes on the screen again.
4. Use
to select OSD menu.
5. Use
to access/confirm the selection.
Move the cursor to yellow area (see red circle on Fig.1)
press OK button to access to factory mode.(see Fig.2)
Fig.4
O-CAL
Fig.6
2.6 Switch light probe to Viewing position.
2.7 Move the Lens barrel forward or backward to get clear image
Fig.2
as shown in Fig. 7
2.8 Switch light probe to Measuring position. It should be able to
PC mode WHITE-D adjustment (B)
1 Apply 1280X1024/60Hz mode with 64 gray level pattern as Fig
indicate colour value on the CA-110.
3. Set main controls brightness control at 100% and contrast to
50% on User mode. Set color setting at original panel color on
User mode. Move cursor to "Auto-SUB" item on factory mode,
press "OK" key to activate this function.
Fig.3
Fig.7
200WP7 LCD
20
Go to cover page
2.9 Adjust the R, G, B Sub-Gain on factory mode for the screen
center, the 1931 CIE chromaticity (X, Y) co-ordinates shall be
as follows.
9300°K
6500°K
x (center)
0.283 ± 0.005
0.313 ± 0.005
y (center)
0.297 ± 0.005
0.329 ± 0.005
Use Minolta CA-110 for colour coordinates and luminance check.
Luminance is > 250 Nits in the center of the screen when
brightness at 100% and contrast set to 100%.
sRGB
x(center)
0.313 ± 0.008
y(center)
0.329 ± 0.008
Ynits
220 ± 10
Factory Preset (B):
After finished all the adjustment, set:
OSD Default Setting:
Brightness: 100%
Contrast: 50%
Adjust size: Full screen
Language: English
Colour: 6500K
OSD position: middle of the LCD screen
Input Selection: Default as PC VGA (D-sub)
Signal cable: Connect to the monitor for user (VGA)
DDC Instructions
21
200WP7 LCD
Go to cover page
General
Pin Assignment
Input DVI-D connector pin assignment
DDC Data Re-programming
In case the DDC data memory IC or main EEPROM which storage all
factory settings were replaced due to a defect, the serial numbers have
to be re-programmed"Analog DDC IC, & EEPROM".
It is advised to re-soldered DDC IC and main EEPROM from the old
board onto the new board if circuit board have been replaced, in this
case the DDC data does not need to be re-programmed.
Additional information
Additional information about DDC (Display Data Channel) may be
obtained from Video Electronics Standards Association (VESA). Extended
Display Identification Data(EDID) information may be also obtained from
VESA.
System and equipment requirements
1.
2.
Fig. 3
To Printer port
DC 8~12V
DC 8~12V
To Monitor
D-sub/DVI cable
To Monitor
D-sub cable
Power
indicator
Power Pin No.
indicator 1
Fig. 1
A. Copy the "UserPort.sys" to C:\WINNT\system32\drivers(win2000)
C:\WINDOWS\system32\drivers(winXP)
B. Running " io.exe" everytime, Before you start to programming
edid data .
3. EDID45.1exe program .
4. DDC 2BI-ISP TOOL:
Fig. 4
Input analog D-SUB connector pin assignment
Note: The EDID45.1EXE is a windows-based program, which cannot
be run in MS-DOS.
To Printer port
TMDS data2TMDS data2+
TMDS data2/4 shield
NC
NC
DDC clock
DDC data
NC
TMDS data1TMDS data1+
TMDS data1/3 shield
NC
NC
+5V
Ground (return for +5V and H/Vsync)
Hot plug detect
TMDS data0TMDS data0+
TMDS data0/5 shield
NC
NC
TMDS clock shield
TMDS clock+
TMDS clock-
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
An i486 (or above) personal computer or compatible.
Microsoft operation system Windows 95/98 .
You have to Install the EDID_PORT_Tool under Win2000/XP . As
Fig. 1 .
Inclusion :
A. DDC2BI-ISP TOOL(3138 106 10396) x1 (as Fig. 2)
B. Printer cable x1
c. (D-Sub) to (D-Sub) cable x2
D. D-SUB to DVI cable X1
Description
Fig. 2
PIN No.
1
SIGNAL
Red
2
Green/ SOG
3
Blue
4
Sense (GND)
5
NC
6
Red GND
7
Green GND
8
Blue GND
9
DDC +5V
10
Cable detect (GND)
11
Sense (GND)
12
Bi-directional data
13
H/H+V sync
14
V-sync
15
Data clock
Fig.5
22
DDC Instructions
200WP7 LCD
Go to cover page
Configuration and procedure
3. At the submenu, type the letter of your computer's hard disk drive
followed by :EDID45 (for example, C:\EDID45, as shown in Fig. 7).
There are 3 chips contained OSD string, serial number..etc
on the circuit board, main EEPROM which storage all factory settings,OSD
string. DDC IC which storage 128byte EDID data(serial number ..etc.).
Following descirptions are the connection and procedure for Analog
/Digital and main EEPROM can be re-programmed along with
Analog/Digital IC by enable factory memory data write function on the
DDC program (EDID45.EXE).
Edid45.exe
Initialize alignment box
In order to avoid that monitor entering power saving mode due
to sync will cut off by alignment box, it is necessary to initialize
alignment box before running programming software
(EDID45.EXE). Following steps show you the procedures and
connection.
Fig. 7
4. Click OK button. The main menu appears (as shown in Fig. 8).
This is for initialize alignment box.
Step 1: Supply 8-12V DC power source to the Alignment box by
plugging a DC power cord or using batteries.
Step 2: Connecting printer cable and D-Sub cable of monitor as Fig. 5
1=Power connector
2=D-SUB/DVI connector
To PC
----->
Fig. 8
DC Power
8-12 V
----->
To printer port (LTP1)
PC
2
1
To Monitor
Printer
Port
Note 1: If the connection is improper, you will see the following error
message (as shown in Fig. 9) before entering the main menu.
Meanwhile, the (read EDID) function will be disable. At this
time,
please make sure all cables are connected correctly and
Fig. 5
Step 3: Installation of EDID45.EXE
Edid45.1
Method 1: Start on DDC program
Start Microsoft Windows.
1. The Program"EDID45.EXE" in service manual cd-rom be copyed to C:\ .
2. Click
, choose Run at start menu of Windows as shown
In Fig. 6.
Fig. 9
1
Note 2: During the loading, EDID45 will verify the EDID data which just
loaded from monitor before proceed any further function, once
the data structure of EDID can not be recognized, the following
error message will appear on the screen as below. Please
confirm following steps to avoid this message.
1. The data structure of EDID was incorrect.
2. DDC IC that you are trying to load data is empty.
3. Wrong communication channel has set at configuration setup
Fig. 10
Fig. 6
DDC Instructions
23
200WP7 LCD
Go to cover page
Re-programming Analog DDC IC
Step 3: Modify DDC data (verify EDID version, week, year)
Step 1: After initialize alignment box, connecting all cables and
box as shown in Fig. 11
1.
1=Power connector
2=D-SUB connector
Click
(new function) icon from the tool bar, bring up
Step 1 of 9 as shown in Fig. 15 .
EDID45 DDC application provides the function selection and
text change (select & fill out) from Step 1 to Step 9.
To Printer
To Printer
Printerport
port
To
port
PC
DC 8~12V
8~12V
DC
DC 8~12V
DC 8~12V
8~12V
DC
To printer port (LTP1)
To Monitor
Monitor
To
ToD-sub/DVI
Monitor cable
To D-sub/DVI
Monitor cable
To
Monitor
D-sub/DVI
cable
D-sub cable
cable
D-sub
Power
Power
indicator
indicator
Power
Power
indicator
indicator
To PC
To Monitor
Printer
Port
Fig. 11
Step 2: Read DDC data from monitor
1.
Click
icon as shown in Fig. 11 from the tool bar to bring up
the Channels "Configuration Setup" windows as shown in Fig. 12.
Fig. 15
Step 4: Modify DDC data (Monitor Serial No.)
1. Click Next to step7, bring up Fig. 16.
- Serial number can be filled up or be changed at this moment.
- Click Finish to exit the Step window.
Fig. 12
2. Select the DDC2Bi as the communication channel.
As shown in Fig. 13.
Fig. 13
3. Click OK button to confirm your selection.
4. Click
icon (Read EDID function) to read DDC EDID data from
monitor. The EDID codes will display on screen as shown in Fig. 14.
Fig. 16
Step 5: Write DDC data
1. Configuration should be as Fig. 17. And press OK.
Fig. 17
To Printer
Printer port
port
To
Fig. 14
DDC Instructions
200WP7 LCD
24
Go to cover page
2. Access Factory Mode
- Turn off monitor.
- [Push AUTO "
" & OK "
" buttons at the same time and
hold it ] + [Press power "
" button untill comes out "Windows
screen"] => then release all button
3. Click
(Write EDID) icon from the tool bar to write DDC data.
Step 6: Save DDC data
Sometimes, you may need to save DDC data as a text file for using
in other IC chip. To save DDC data, follow the steps below:
Step 8: Modify serial number in OSD
-1. Unzip the serial number.zip to your computer, then open the folder
as shown in Fig.20.
-2. If use Win98 OS, you can execute SN.exe directly.
If use Win2000 or XP OS, first, you must execute install.bat, then
execute SN.exe
-3. Set I2C bus(press the left-top button of operating window) as shown
in Fig.21, then press " SET" button.
-4. Set Block2 as shown in Fig.22
-5. key in new serial number, then press " Write" button as shown in
Fig.22 , Click " WRITE" button.
-6. It will appear" Serial Number Write OK" , Click" Enter" to finish it.
1. Click
(Save) icon (or click "file"-> "save as") from the tool bar
And give a file name as shown in Fig. 18.
The file type is EDID45 file (*.ddc) which can be open in WordPad.
By using WordPad, the texts of DDC data & table (128 bytes, hex
code) can be modified. If DDC TEXTS & HEX Table are completely
correct, it can be saved as .ddc flie to re-load it into DDC IC for DDC
Data application.
Fig.20
200WP7
Fig.18
Analog
Fig. 25
2.
Click Save.
Fig.21
Step 7: Exit DDC program
Pull down the File menu and select Exit as shown in Fig. 19.
Edid45.1
Fig.22
Fig. 19
Step9:
-1. Disconnect the monitor power cord and connect it again.
-2. Press the OK button to bring up the OSD main manu.
-3. Re-confirm the serial Number is updated as shown in Fig.23.
Fig.23
DDC Instructions
25
200WP7 LCD
Go to cover page
Re-programming Digital DDC IC
Step 3: Modify DDC data (verify EDID version, week, year)
Step 1: After initialize alignment box, connecting all cables and
box as shown in Fig. 24
1.
1=DVI connector
2=D-SUB connector
3=Power Plug
Click
(new function) icon from the tool bar, bring up
Step 1 of 9 as shown in Fig. 28 .
EDID45 DDC application provides the function selection and
text change (select & fill out) from Step 1 to Step 9.
To Printer
port
To Printer
port
DC 8~12VDC 8~12V
DC8~12V
8~12V
DC
To Monitor
ToTo
Monitor
D-sub/DVI cable
Monitor
To Monitor
D-sub/DVI
cable
D-sub/DVI
cable
D-sub cable
Power
indicator
3
Power
indicator
To PC
To Monitor
Printer
Port
Fig.24
Step 2: Read DDC data from monitor
1.
Click
icon as shown in Fig. 25 from the tool bar to bring up
the Channels "Configuration Setup" windows as shown in Fig. 26.
Fig. 28
Step 4: Modify DDC data (Monitor Serial No.)
1. Click Next , bring up Fig. 29. Then select Digital Signal as below
Fig. 25
2. Select the DDC2Bi as the communication channel.
As shown in Fig. 26.
Fig. 26
3. Click OK button to confirm your selection.
4. Click
icon (Read EDID function) to read DDC EDID data from
monitor. The EDID codes will display on screen as shown in Fig. 27.
To Printer port
Fig. 27
Fig. 29
2. Click Next to step7, bring up Fig. 30.
- Serial number can be filled up or be changed at this moment.
- Click Finish to exit the Step window.
Fig. 30
DDC Instructions
200WP7 LCD
26
Go to cover page
Step 5: Write DDC data
1. Configuration should be as Fig. 31. And press OK.
BOM Code
Panel Supplier
CODE
AUO
1
CPT
2
LPL(LG)
3
QDI
4
CMO
5
BZ3A0601000001
SERIAL NO
Fig. 31
SERVICE VERSION CHANGE CODE
2. Access Factory Mode
- Turn off monitor.
- [Push AUTO "
" & OK "
" buttons at the same time and
hold it ] + [Press power "
" button untill comes out "Windows
screen"] => then release all button
3. Click
(Write EDID) icon from the tool bar to write DDC data.
Step 6: Save DDC data
Sometimes, you may need to save DDC data as a text file for using
in other IC chip. To save DDC data, follow the steps below:
1. Click
(Save) icon (or click "file"-> "save as") from the tool bar
And give a file name as shown in Fig. 32.
The file type is EDID46 file (*.ddc) which can be open in WordPad.
By using WordPad, the texts of DDC data & table (128 bytes, hex
code) can be modified. If DDC TEXTS & HEX Table are completely
correct, it can be saved as .ddc flie to re-load it into DDC IC for DDC
Data application.
200P7
Fig. 32
2.
YEAR/WEEK
Click Save.
Step 7: Exit DDC program
Pull down the File menu and select Exit as shown in Fig. 33.
Edid45.1
Fig. 33
BOM CODE(BILL OF MATERIAL)CODE
SITE CODE(PRODUCTION CENTER)
BZ CODE(AR-CZECH REPUBLIC
VN-HUNGARY(SZR),BZ-SUZHOU
DS-DONGGUAN)
DDC Data
200WP7 LCD
27
Go to cover page
THE DISPLAY DATA CHANNEL (DDC 2B) CONTENT INCLUDING
(FOR HUDSON 7-200WP7 Analog AUO panel)
**********************************************************************
EDID log file for 200WP7 Analog
**********************************************************************
Vendor/Product Identification
ID Manufacturer Name
: PHL
ID Product Code
: 0843 (HEX.)
ID Serial Number
: 123456 (DEC.)
Week of Manufacture
: 50
Year of Manufacture
: 2005
EDID Version, Revision
Version
: 1
Revision
: 3
Basic Display Parameters/Features
Video Input Definition
: Analog Video Input
0.700V/0.300V (1.00Vpp)
without Blank-to-Black Setup
Separate Sync
Composite Sync
Sync on Green
no Serration required
Maximum H Image Size
: 43
Maximum V Image Size
: 27
Display Transfer Characteristic : 2.2
(gamma)
: Standby
Feature Support (DPMS)
Suspend
Active Off
Display Type
: RGB color display
Standard Default Color Space : Primary color space
Preferred Timing Mode
: Detailed timing block 1
Color Characteristics
Red X coordinate
: 0.64
Red Y coordinate
: 0.352
Green X coordinate
: 0.288
Green Y coordinate
: 0.628
Blue X coordinate
: 0.144
Blue Y coordinate
: 0.076
White X coordinate
: 0.313
: 0.329
White Y coordinate
Established Timings
Established Timings I
:
720 x 400 @70Hz (IBM,VGA)
640 x 480 @60Hz (IBM,VGA)
640 x 480 @67Hz (Apple,Mac II)
640 x 480 @72Hz (VESA)
640 x 480 @75Hz (VESA)
800 x 600 @56Hz (VESA)
800 x 600 @60Hz (VESA)
Established Timings II
:
800 x 600 @72Hz (VESA)
800 x 600 @75Hz (VESA)
832 x 624 @75Hz (Apple,Mac II)
1024 x 768 @60Hz (VESA)
1024 x 768 @70Hz (VESA)
1024 x 768 @75Hz (VESA)
1280 x 1024 @75Hz (VESA)
Manufacturer's timings
: 1152 x 870 @75Hz (Apple,Mac II)
Standard Timing Identification #1
Horizontal active pixels
:
1152
Aspect Ratio
: 4:3
Refresh Rate
:
70
Standard Timing Identification #2
Horizontal active pixels
:
1152
Aspect Ratio
: 4:3
Refresh Rate To Printer port
:
75
Standard Timing Identification #3
Horizontal active pixels
: 1280
Aspect Ratio
: 4:3
Refresh Rate
: 60
Standard Timing Identification #4
Horizontal active pixels
: 1280
Aspect Ratio
: 5:4
To Printer port
Refresh Rate
: 60
Standard Timing
Identification #5
DC 8~12V
Horizontal
: 1600
DC 8~12V active pixels
To Monitor : 4:3
Aspect Ratio
D-sub/DVI cable: 60
Refresh Rate
To Monitor
Standard Timing
Identification
#6
D-sub cable
Horizontal
: 1680
Poweractive pixels
Aspectindicator
Ratio
: 16:10
Refresh Rate
: 60
Power
Standard Timing Identification #7
indicator
Horizontal active pixels
: 1680
Aspect Ratio
: 16:10
Refresh Rate
: 75
Detailed Timing #1
Pixel Clock (MHz)
: 146
H Active (pixels)
: 1680
H Blanking (pixels)
: 560
V Active (lines)
: 1050
V Blanking (lines)
: 39
H Sync Offset (F Porch) (pixels): 104
H Sync Pulse Width (pixels) : 176
V Sync Offset (F Porch) (lines) : 3
V Sync Pulse Width (lines)
: 6
H Image Size (mm)
: 433
V Image Size (mm)
: 271
H Border (pixels)
: 0
V Border (lines)
: 0
Flags
: Non-interlaced
: Normal Display, No stereo
: Digital Separate sync.
: Positive Vertical Sync.
: Positive Horizontal Sync.
Monitor Descriptor #2
Serial Number
: TY 123456
Monitor Descriptor #3
Monitor Name
: Philips 200WP
Monitor Descriptor #4
Monitor Range Limits
Min. Vt rate Hz
: 56
Max. Vt rate Hz
: 76
Min. Horiz. rate kHz
: 30
Max. Horiz. rate kHz
: 98
Max. Supported Pixel
: 210
No secondary GTF timing formula supported.
Extension Flag
: 0
Check sum
: 6C (HEX.)
**********************************************************************
EDID data (128 bytes)
**********************************************************************
0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00
8: 41 9: 0c 10: 43 11: 08 12: 40 13: e2 14: 01 15: 00
16: 32 17: 0f 18: 01 19: 03 20: 1e 21: 2b 22: 1b 23: 78
24: ee 25: cf 26: e5 27: a3 28: 5a 29: 49 30: a0 31: 24
32: 13 33: 50 34: 54 35: bf 36: ef 37: 80 38: 71 39: 4a
40: 71 41: 4f 42: 81 43: 40 44: 81 45: 80 46: a9 47: 40
48: b3 49: 00 50: a9 51: 4f 52: b3 53: 0f 54: 08 55: 39
56: 90 57: 30 58: 62 59: 1a 60: 27 61: 40 62: 68 63: b0
64: 36 65: 00 66: b1 67: 0f 68: 11 69: 00 70: 00 71: 1e
72: 00 73: 00 74: 00 75: ff 76: 00 77: 20 78: 54 79: 59
80: 20 81: 20 82: 31 83: 32 84: 33 85: 34 86: 35 87: 36
88: 0a 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50
96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 32
104: 30 105: 30 106: 57 107: 50 108: 00 109: 00 110: 00 111: fd
112: 00 113: 38 114: 4c 115: 1e 116: 62 117: 15 118: 00 119: 0a
120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: 6c
28
200WP7 LCD
DDC Data
Go to cover page
THE DISPLAY DATA CHANNEL (DDC 2B) CONTENT INCLUDING
(FOR HUDSON7-200WP7 Digital QDI panel)
**********************************************************************
EDID log file for 200WP7 Digital
**********************************************************************
Vendor/Product Identification
ID Manufacturer Name
: PHL
ID Product Code
: 0843 (HEX.)
ID Serial Number
: 123456 (DEC.)
Week of Manufacture
: 50
Year of Manufacture
: 2005
EDID Version, Revision
Version
: 1
Revision
: 3
Basic Display Parameters/Features
Video Input Definition
: Digital Video Input
Compatible with VESA DFP 1.x
Maximum H Image Size
: 43
Maximum V Image Size
: 27
Display Transfer Characteristic : 2.2
(gamma)
Feature Support (DPMS)
: no Standby
no Suspend
Active Off
Display Type
: RGB color display
Standard Default Color Space : Primary color space
Preferred Timing Mode
: Detailed timing block 1
Color Characteristics
Red X coordinate
: 0.64
Red Y coordinate
: 0.352
Green X coordinate
: 0.288
Green Y coordinate
: 0.628
Blue X coordinate
: 0.144
Blue Y coordinate
: 0.076
White X coordinate
: 0.313
White Y coordinate
: 0.329
Established Timings
Established Timings I
: 720 x 400 @70Hz (IBM,VGA)
640 x 480 @60Hz (IBM,VGA)
640 x 480 @67Hz (Apple,Mac II)
640 x 480 @72Hz (VESA)
640 x 480 @75Hz (VESA)
800 x 600 @56Hz (VESA)
800 x 600 @60Hz (VESA)
Established Timings II
: 800 x 600 @72Hz (VESA)
800 x 600 @75Hz (VESA)
832 x 624 @75Hz (Apple,Mac II)
1024 x 768 @60Hz (VESA)
1024 x 768 @70Hz (VESA)
1024 x 768 @75Hz (VESA)
1280 x 1024 @75Hz (VESA)
Manufacturer's timings
: 1152 x 870 @75Hz (Apple,Mac II)
Standard Timing Identification #1
Horizontal active pixels
: 1152
Aspect Ratio
: 4:3
Refresh Rate
: 70
Standard Timing Identification #2
Horizontal active pixels
: 1152
Aspect Ratio
: 4:3
Refresh Rate
: 75
Standard Timing Identification #3
Horizontal active pixels
: 1280
Aspect Ratio
: 4:3
Refresh Rate
: 60
Standard Timing Identification #4
Horizontal active pixels
: 1280
Aspect Ratio
Refresh Rate
: 5:4
: 60
Standard Timing Identification #5
Horizontal active pixels
: 1600
Aspect Ratio
: 4:3
Refresh Rate
: 60
Standard Timing Identification #6
Horizontal active pixels
: 1680
Aspect Ratio
: 16:10
Refresh Rate
: 60
Detailed Timing #1
Pixel Clock (MHz)
: 146
H Active (pixels)
: 1680
H Blanking (pixels)
: 560
V Active (lines)
: 1050
V Blanking (lines)
: 39
H Sync Offset (F Porch) (pixels): 104
H Sync Pulse Width (pixels) : 176
V Sync Offset (F Porch) (lines) : 3
V Sync Pulse Width (lines)
: 6
H Image Size (mm)
: 433
V Image Size (mm)
: 271
H Border (pixels)
: 0
V Border (lines)
: 0
Flags
: Non-interlaced
: Normal Display, No stereo
: Digital Separate sync.
: Positive Vertical Sync.
: Positive Horizontal Sync.
Monitor Descriptor #2
Serial Number
: TY 123456
Monitor Descriptor #3
Monitor Name
: Philips 200WP
Monitor Descriptor #4
Monitor Range Limits
Min. Vt rate Hz
: 56
Max. Vt rate Hz
: 76
Min. Horiz. rate kHz
: 30
Max. Horiz. rate kHz
: 98
Max. Supported Pixel
: 170
No secondary GTF timing formula supported.
Extension Flag
: 0
Check sum
: 83 (HEX.)
**********************************************************************
EDID data (128 bytes)
**********************************************************************
0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00
8: 41 9: 0c 10: 43 11: 08 12: 40 13: e2 14: 01 15: 00
16: 32 17: 0f 18: 01 19: 03 20: 81 21: 2b 22: 1b 23: 78
24: 2e 25: cf 26: e5 27: a3 28: 5a 29: 49 30: a0 31: 24
32: 13 33: 50 34: 54 35: bf 36: ef 37: 80 38: 71 39: 4a
40: 71 41: 4f 42: 81 43: 40 44: 81 45: 80 46: a9 47: 40
48: b3 49: 00 50: 01 51: 01 52: 01 53: 01 54: 08 55: 39
56: 90 57: 30 58: 62 59: 1a 60: 27 61: 40 62: 68 63: b0
64: 36 65: 00 66: b1 67: 0f 68: 11 69: 00 70: 00 71: 1e
72: 00 73: 00 74: 00 75: ff 76: 00 77: 20 78: 54 79: 59
80: 20 81: 20 82: 31 83: 32 84: 33 85: 34 86: 35 87: 36
88: 0a 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50
96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 32
104: 30 105: 30 106: 57 107: 50 108: 00 109: 00 110: 00 111: fd
112: 00 113: 38 114: 4c 115: 1e 116: 62 117: 11 118: 00 119: 0a
120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: 83
ISP Instruction
200WP7 LCD
29
Go to cover page
Double click the shortcut
Configuration and procedure
on the desktop
Fig. 4
"Easywriter " The software is provided by Novatek to upgrade the
firmware of CPU.
It is a windows-based program, which cannot be run in MS-DOS.
The tool (3138 106 10396) is for the interface between "Parallel Port of
PC" and "15 pin-D-SUB connector of Monitor".
To Printer port
DC 8~12V
DC 8~12V
To Monitor
D-sub/DVI cable
System and equipment requirements
1.
2.
3.
4.
To Monitor
D-sub cable
An i486 (or above) personal computer or compatible.
Microsoft operation system Windows 95/98/2000/XP.
ISP Software " Easywrite "
ISP TOOL (3138 106 10396) as shown in Fig. 1
Power
indicator
Step 5 :Copy the .hex code to C:\200WP7 as shown in Fig. 5 .
Power
indicator
170S5
Fig. 1
5.
Fig. 5
Update the firmware
1. Press the load hex then select the .hex code as shown in Fig.6
Connect ISP TOOL and Mains cord to Monitor as shown
in Fig. 2.
Fig. 6
PC
200WP7 LCD (B)
Monitor (A)
Connect to
Mains cord
Video cable
To printer port (LTP1)
To video card
D-Sub
AC POWER
DC 8-12V
2. Press the AUTO to run the program,the firmware be updated as
shown in Fig7`Fig.8
+
To
Port
ToPC
313810610396
6. Run the Easywriter program
Step 1 : Make a folder in your PC as shown in Fig. 3.
For example : C:\easywrite
Step 2 : Copy ISP Software Easywriter.zip into your folder
as shown in Fig.3.
Step 3 : Unzip Easywriter.zip into your folder as shown in Fig. 3.
Fig. 7
Step 4 : Double click the EasywriterV2.09.exe icon to run the
Application as Fig. 4.
170S5
Fig.8
To Printer port
30
ISP Instruction
200WP7 LCD
Go to cover page
Press the file
exit to end program, as shown in Fig.9
Fig.9
If there is a warring message coming as shown in Fig 10. , you
have to check the AC power, Video cable, or Novatek MCU.
You can enter factory mode to confirm the CPU version
Electrical instructions
1.
General points
1.1
Item
H.Freq.
(KHz)
Mode
Resolution
V.Freq.
(Hz)
9
48.363
VESA
1024x768
60.004
10
60.023
VESA
1024x768
75.029
11
68.700
MACINTOSH
1152x870
75.000
12
63.981
VESA
1280x1024
60.020
13
79.976
VESA
1280x1024
75.025
14
75.0
VESA
1600x1200
60
15
65.29
-
1680x1050
60.0
During the test and measuring, supply a distortion free AC
mains voltage to the apparatus via an isolated transformer
with low internal resistance.
1.2
All measurements mentioned hereafter are carried out at a
Normal mains voltage (90 - 132 VAC for USA version,
195 -264 VAC for EUROPEAN version, or 90 - 264 VAC for
the model with full range power supply, unless otherwise stated.)
1.3
All voltages are to be measured or applied with respect to
ground, unless otherwise stated.
Note: don‘t use heat-sink as ground.
1.4
The test has to be done on a complete set including LCD
panel in a room with temperature of 25 +/- 5 degree C.
1.5
All values mentioned in these test instruction are only
applicable of a well aligned apparatus, with correct signal.
1.6
The letters symbols (B) and (S) placed behind the test
instruction denotes
(B): carried out 100% inspection at assembly line
(S): carried out test by sampling
1.7
1.9
2.
Preset Modes (40modes)
Item
H.Freq.
(KHz)
Mode
Resolutio
n
V.Freq.
(Hz)
1
31.469
IBM VGA 10H
640x350
70.086
2
31.469
IBM VGA 3H
720x400
70.087
3
31.469
IBM VGA 12H
640x480
59.940
Repetitive power on/ off cycle are allowed. The image can
be displayed after 8 sec.
4
35.000
MACINTOSH
640x480
67.000
5
37.861
VESA
640x480
72.809
All optical characteristics (including WHITE-D, Brightness,
and so on) are determined according to panel specification
after warming up approximate 30 minutes that brightness
stability is optimal, and follow strictly after panel specification.
6
37.500
VESA
640x480
75.000
7
43.269
VESA
640x480
85.008
8
35.156
VESA
800x600
56.250
9
37.879
VESA
800x600
60.317
10
48.077
VESA
800x600
72.188
11
46.875
VESA
800x600
75.000
12
53.674
VESA
800x600
85.061
13
49.700
MACINTOSH
832x624
75.000
14
56.4
-
960x720
75
15
44.75
-
960x720
60
16
48.363
VESA
1024x768
60.004
17
56.476
VESA
1024x768
70.069
18
60.023
VESA
1024x768
75.029
19
61.080
IBM XGA-2
1024x768
75.781
20
68.677
VESA
1024x768
84.997
21
47.776
CVT 2.3MA
1280
x768
60
Item
H.Freq.
(KHz)
Mode
Resolution
V.Freq. (Hz)
CVT 2.3MA
1280 x768
75
1152x864
60
1152x864
70.012
The white balance (color temperature), has to be tested
in subdued lighted room.
1.8
31
200WP7 LCD
Go to cover page
Input signal
Signal type
2.1.1
Analogue Video: 0.7 Vp-p linear, positive polarity
Sync. : TTL level, separate, positive or negative polarity
Signal source: pattern generator format as the SPEC.
Reference generator: QuantumData 802G/ 802BT
2.1.2
Digital Video: 600mVp-p TMDS Signal
2.1.3
Audio Signal: PC line in
2.2
Input signal mode
(1) Factory Preset Modes (15modes)
Item
H.Freq.
(KHz)
Mode
Resolution
V.Freq.
(Hz)
1
31.469
IBM VGA 10H
640x350
70.086
2
31.469
IBM VGA 3H
720x400
70.087
3
31.469
IBM VGA 12H
640x480
59.940
4
35.000
MACINTOSH
640x480
67.000
5
37.500
VESA
640x480
75.000
6
35.156
VESA
800x600
56.250
7
37.879
VESA
800x600
60.317
22
60.289
8
46.875
VESA
800x600
75.000
23
54.1
24
63.851
VESA
32
Electrical instructions
200WP7 LCD
Go to cover page
25
67.500
VESA
1152x864
75.000
26
68.700
MACINTOSH
1152x870
75.000
x(center)
0.313 ± 0.008
27
61.845
SUN WS
1152x900
66.004
y(center)
0.329 ± 0.008
28
71.810
SUN WS
1152x900
76.150
Ynits
220 ± 10
29
60.000
VESA
1280x960
60.000
30
75.000
VESA
1280x960
75.000
31
63.981
VESA
1280x1024
60.020
32
71.691
SUN WS
1280x1024
67.189
33
76.000
DOS/V
1280x1024
72.000
34
79.976
VESA
1280x1024
75.025
35
81.130
SUN WS
1280x1024
76.110
36
91.1
VESA
1280x1024
85.0
37
78.36
CVT 2.3MA
1600x1000
75.0 (for DSub)
38
75.0
VESA
1600x1200
60.0
39
65.29
VESA
1680*1050
59.883
40
82.306
VESA
1680*1050
74.892
41
42
3.
AC, DC power board
3.1 Setup the AC I/P at 90VAC, and Output DC 12V loading 1.1A
(AU 0.6A), the DC output voltage is 12.0 +/-0 0.6 V DC, Adjusting is
no need. and 5V loading 1.0A(AU 2.7A), the DC output voltage is
5V+/-0.25VDC. (B)
4. Display Adjustment
4.1
Access to factory mode (IIC) in auto-alignment system
The communication protocol switch to IIC.
4.2
Auto color adjustment (B)
Apply a 1280x1024/60Hz signal with Blackand white
levels pattern, set brightness control at 100%, and contrast
control at 50%.
Adjust the R. G. B offset, and gain to calibrate the color
smoothly and 64-gray level distinguishable.
Check all factory pre-setting modes.
4.3
Adjustment of WHITE-D (B)
Apply a 1280*1024 / 60Hz signal with white pattern, set
brightness control at 100%, and contrast control at 50%.
Adjust the R, G, B Sub-Gain, for the screen
center, the 1931 CIE chromaticity (X, Y) co-ordinates shall be;
x (center)
9300°K
6500°K
0.283 ± 0.005
0.313 ± 0.005
y (center)
0.297 ± 0.005
0.329 ± 0.005
Use Minolta CA-110 for colour coordinates and luminance check.
Luminance is > 240 Nits in the center of the screen when
brightness at 100% and contrast set to 100%.
4.4
Adjustment of sRGB
Apply a 1280*1024 / 60Hz signal with white pattern, set brightness
control at 100%, and contrast control at 50%. Adjust the R, G, B
Sub-Gain, for the screen center, the 1931 CIE chromaticity (X, Y)
co-ordinates shall be;
sRGB
Repair Tips
33
200WP7 LCD
Go to cover page
0. Warning
preferably be equipped with a thermal control (soldering
All ICs and many other semi-conductors are susceptible to
temperature: 225 to 250 C).
electrostatic discharges (ESD). Careless handling during
- The chip, once removed, must never be reused.
repair can reduce life drastically. When repairing, make sure
1.4 Attachment of SMDs
that you are connected with the same potential as the mass
- Locate the SMD on the solder lands by means of tweezers
of the unit via a wrist wrap with resistance. Keep components
and solder the component on one side. Ensure that the
and tools also at the same potential !
component is positioned correctly on the solder lands (see Fig.2A).
1. Servicing of SMDs (Surface Mounted Devices)
- Next complete the soldering of the terminals of the
1.1 General cautions on handling and storage
component (see Fiq. 2B).
- Oxidation on the terminals of SMDs results in poor soldering.
Do not handle SMDs with bare hands.
- Avoid using storage places that are sensitive to oxidation
such as places with sulphur or chlorine gas, direct sunlight,
high temperatures or a high degree of humidity. The
capacitance or resistance value of the SMDs may be
affected by this.
- Rough handling of circuit boards containing SMDs may
cause damage to the components as well as the circuit
boards. Circuit boards containing SMDs should never be
bent or flexed. Different circuit board materials expand and
contract at different rates when heated or cooled and the
2. Caution when attaching SMDs
components and/or solder connections may be damaged
- When soldering the SMD terminals, do not touch them
due to the stress. Never rub or scrape chip components as
directly with the soldering iron. The soldering should be
this may cause the value of the component to change.
done as quickly as possible, care must be taken to avoid
Similarly, do not slide the circuit board across any surface.
damage to the terminals of the SMDs themselves.
- Keep the SMD's body in contact with the printed board when
1.2 Removal of SMDs
soldering.
- Heat the solder (for 2-3 seconds) at each terminal of the
- The soldering iron to be used (approx. 30 W ) should
chip. By means of litz wire and a slight horizontal force,
preferably be equipped with a thermal control (soldering
small components can be removed with the soldering iron.
temperature: 225 to 250 C).
They can also be removed with a solder sucker (see Fig.
- Soldering should not be done outside the solder land.
1A)
- Soldering flux (of rosin) may be used, but should not be
acidic.
- After soldering, let the SMD cool down gradually at room
temperature.
- The quantity of solder must be proportional to the size of the
solder land. If the quantity is too great, the SMD might
crack or the solder lands might be torn loose from the
printed board (see Fig. 3).
While holding the SMD with a pair of tweezers, take it off gently using the
Right
soldering iron's heat applied to each terminal (see Fig. 1 B).
- Remove the excess solder on the solder lands by means of
litz wire or a solder sucker (see Fig. 1C).
1.3 Caution on removal
- When handling the soldering.iron. use suitable pressure and be careful.
- When removing the chip, do not use undue force with the pair of tweezers.
- The soldering iron to be used (approx. 30 W) should
Fig.3 Examples
34
200WP7 LCD
Repair Tips
Go to cover page
3. Lead-free product identification
You can identify lead-free product by Philips-lead-free logo on PCB.
P
b
4. Lead-free product repair instruction
4.1 Use only lead-free Solder Alloy 0622 149 00106(1.2mm SAC305) or 0622 149
00108(1.0mm SAC305).
Remark: For lead free soldering material, please visit www.alphametals.com website for
details. This is recommended by Philips.
4.2 Use only adequate solder tools applicable for lead-free soldering-tin. The solder tool must be able to reach at least a
solder-temperature of 400 , to stabilize the adjusted temperature at the solder-tip and to exchange solder-tips for different
applications.
Small Passives/Actives to be removed with thermal tweezers
Automated system for IC and BGA repair (Microscope, Camera, Beam split optics, Computer, Programmer, Heat
controllers, Vacuum system, Laser pointer)
Solder Hand-Tool (Adjustable in temperature height, Temperature shall be held constant,
Flexible tips)
4.3 Adjust your solder tool so that a temperature around 360 -380 is reached and stabilized at the solder joint.
Heating-time of the solder-joint should not exceed ~ 4 sec. Avoid temperatures above 400 otherwise wear-out of tips will
rise drastically and flux-fluid will be destroyed.
Corrosion of Tool-Spikes can be avoided when using SAC305 and a temperature of less than 400 .
4.4 Mix of lead-free solder-tin/parts with leaded soldering-tin/parts is possible but not recommended. If not to avoid clean
carefully the solder-joint from old tin and re-solder with new tin.
4.5 Use only original spare-parts listed in the Service-Manuals. Standard-material
(consumables) can also be purchased at external companies.
4.6 Special information for lead-free BGA-ICs: this ICs will be delivered in so-called
dry-packaging to protect the IC against moisture and with lead-free logo on it. This
packaging may only be opened shortly before it is used (soldered). Otherwise the
body of the IC gets " wet " inside and during the heating time the structure of the IC
will be destroyed due to high (steam-)pressure. If the packaging was opened before
usage the IC has to be heated up for some hours (around 90 ) for drying (Take
attention for ESD-protection!)
5. Rework on BGA (Ball Grid Array) ICs
General
Although (LF)BGA assembly yields are very high, there may still be a requirement for component rework. By rework, we
mean the process of removing the component from the PWB and replacing it with a new component. If an (LF)BGA is
removed from a PWB, the solder balls of the component are deformed drastically so the removed (LF)BGA has to be
discarded.
Device Removal
As is the case with any component that, it is essential when removing an (LF)BGA, the board, tracks, solder lands, or
surrounding components are not damaged. To remove an (LF)BGA, the board must be uniformly heated to a temperature
close to the reflow soldering temperature. A uniform temperature reduces the chance of warping the PWB.
To do this, we recommend that the board is heated until it is certain that all the joints are molten. Then carefully pull the
component off the board with a vacuum nozzle. For the appropriate temperature profiles, see the IC data sheet.
Area Preparation
When the component has been removed, the vacant IC area must be cleaned before replacing the (LF)BGA.
Removing an IC often leaves varying amounts of solder on the mounting lands. This excessive solder can be removed with
either a solder sucker or solder wick. The remaining flux can be removed with a brush and cleaning agent. After the board
is properly cleaned and inspected, apply flux on the solder lands and on the connection balls of the(LF)BGA
Note: Do not apply solder paste, as this has shown to result in problems during re-soldering.
Device Replacement
The last step in the repair process is to solder the new component on the board. Ideally, the (LF)BGA should be
aligned under a microscope or magnifying glass. If this is not possible, try to align the (LF)BGA with any board markers.
To reflow the solder, apply a temperature profile according to the IC data sheet. So as not to damage neighbouring
components, it may be necessary to reduce some temperatures and times.
More Information
For more information on how to handle BGA devices, visit this URL: http://www.atyourservice.ce.philips.com (needs
subscription). After login, select " Magazine ", then go to " Workshop Information ". Here you will find Information on how
.to deal with BGA-ICs.
Repair Flow Chart
200WP7 LCD
Go to cover page
AC IN
Power Board
Control Board
Scaler Board
LCD Panel
No power
(power indicator off)
NG
Check 12V/5V/3.3V
Bad power board
OK
Bad Scaler Board
NG
Check Scaler Board
OK
Check Control Board
OK
Check LCD Panel
Check Control Wires
35
36
200WP7 LCD
Repair Flow Chart
21
X
Go to cover page
NG
Power Board
Bad Power Board
OK
OK
OK
Check Scaler Board
OK
OK
Bad Scaler Board
Repair Flow Chart
OK
OK
OK
Check
Power Board
OK
Check LCD Panel
Control Board
OK
OK
Board
37
200WP7 LCD
Go to cover page
38
200WP7 LCD
Go to cover page
200WP7 Block Diagram
Block Diagram
Panel Backlight
(3 CCFL)
Panel
• wire harness(LVDS)
30 Pin
RGB//DE/Hsync/Vsync
Panel Vcc
(5V for QDI/AU)
Scalar(LVDS interface)
30 pin wafer
Connector
Dual input
Connector
AC-DC Power supply
Connector Inverter and
DC-DC converter
(132 mm x 75mm)
Connector
Connector
(200mm x 150mm)
Connector
DVI_D
D_SUB
Connector
AC
input
Panel Backlight
(3 CCFL)
Control Board
USB Hub
Scaler Diagram-1
200WP7 LCD
39
40
200WP7 LCD
Scaler Diagram-2
Scaler Diagram-3
200WP7 LCD
41
42
200WP7 LCD
Scaler Diagram-4
Scaler Diagram-5
200WP7 LCD
43
44
200WP7 LCD
Scaler Board C.B.A.-1
Scaler Board C.B.A.-2
200WP7 LCD
45
46
200WP7 LCD
Scaler Board C.B.A.-3
Power Diagram-1
200WP7 LCD
47
48
200WP7 LCD
Power Diagram-2
Power Board C.B.A.-1
200WP7 LCD
49
50
200WP7 LCD
Power Board C.B.A.-2
200WP7 LCD
51
52
200WP7 LCD
200WP7 LCD
53
54
200WP7 LCD
200WP7 LCD
55
56
200WP7 LCD
Go to cover page
21
X
GENERAL PRODUCT SPECIFICATION
HUDSON7-200WP7 20.1"
GENERAL PRODUCT
SPECIFICATION
. ANALOG AND DIGITAL DUAL INPUT
. AUTO PICTURE ADJUSTMENT
. 15 FACTORY PRESET MODES AND 40 PRESET MODES WHICH
CAN BE RECOVERED TO PRESET MODES, 25 USER MODES
. USER FRIENDLY OSD DISPLAY FOR MODE IDENTIFICATION
/ADJUSTMENT
. DDC 2B COMMUNICATION CAPABILITY
. MAX. RESOLUTION 1680*1050 NON-INTERLACED AT 76 HZ
. 20.1 "COLOR TFT LCD FLAT PANEL
. EASY TILT & FOLDABLE BASE
. FULL RANGE POWER SUPPLY 90 - 264 VAC
. CE ENVIRONMENTAL POLICY
. ANTI-GLARE TO REDUCE LIGHT REFLECTION
. POWER MANAGEMENT CAPABILITY
. SOG SUPPORT
. TCO 03
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
1
200WP7 LCD
57
58
GENERAL PRODUCT SPECIFICATION(Continued)
200WP7 LCD
CONTENTS
1.0
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
Foreword
Product profile
LCD
Scanning frequencies
Video dot rate
Power input
Power consumption
Dimensions
Weight
Functions
Ambient temperature
Regulatory compliance
3.0
3.1
3.1.1
3.2
3.2.1
3.2.2
3.2.3
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.4
3.5
3.6
3.6.1
3.6.2
Electrical characteristics
Interface signals
Video
Interface
D-sub cable
DVI cable
OSD function control
Timing requirement
Mode storing capacity
Preset timings
Horizontal scanning
Vertical scanning
Power input connection
Power management
Display identification
Analog DDC
Digital DDC
4.0
4.1
4.2
4.3
Visual characteristics
Test conditions
Resolution
Brightness
4.4
4.4.1
4.4.2
4.5
4.6
4.7
Image size
Actual display size
Max. scan size
Brightness uniformity
Cross-talk
White color adjustment
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
2
GENERAL PRODUCT SPECIFICATION
5.0
5.1
5.2
5.3
5.4
5.4.1
5.4.2
Mechanical characteristics
Controls
Unit dimension / weight
Tilt and swivel base
Transportation packages
Shipping dimension / weight
Block unit / palletization
6.0
6.1
6.2
6.3
6.4
6.4.1
Environmental characteristics
Susceptibility of display to external environment
Transportation tests
Display disturbances from external environment
Display disturbances to external environment
EMI
7.0
7.1
8.0
8.1
9.0
Reliability
Mean time between failures
Quality assurance requirements
Acceptance test
Serviceability
10.0
Lcd panel characteristics requirements
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
3
200WP7 LCD
59
60
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
1.0
FOREWORD
This specification describes a 20.1" WSXGA multi-scan color TFT
LCD monitor with max. resolution up to 1680*1050/ 60 Hz(digital)
/1680*1050/75Hz(analog) non-interlaced.
All optical characteristics (including WHITE-D, Brightness, and so on) are
determined according to panel specification after warming up approximate
30 minutes that brightness stability is optimal, and follows strictly after panel specification.
2.0
PRODUCT PROFILE
This display monitor unit is a color display monitor enclosed in PHILIPS global styling
cabinet, which has an integrated tilt and swivel base.
2.1
LCD
Type NR.
: LM201W01 SLA1 (LG.PHILIPS)
Outside dimensions
: 459.4(H)*296.4(V)*22.8(D) (Typ) mm
Pixel Pitch ( mm )
: 0.258 mm x 0258mm
Color pixel arrangement : RGB vertical stripes
Display surface
: low reflection, antiglare with hard coating
Color depth
: 16.7M colors (8 bits)
Backlight
: Six CCFL‘s
Active area(WxH)
: 433.44x270.9mm (20.1”W diagonal)
View angle
: Horizontal & Vertical 178 degree (CR>=10)
Contrast ratio
: 600:1 (Typ) ,500 :1 (min)
White luminance
: Panel original color >250nits (min), 300 nits (Typ.)
Type NR.
: M201EW01 V0 (AUO)
Outside dimensions
: 459.4(H)*296.4(V)*22.8(D) (Typ.) mm
Pixel Pitch ( mm )
: 0.258 mm x 0258mm
Color pixel arrangement : RGB vertical stripes
Display surface
: low reflection, antiglare with hard coating
Color depth
: 16.7M colors (8 bits)
Backlight
: Six CCFL‘s
Active area(WxH)
: 433.44x270.9mm (20.1”W diagonal)
View angle
: Horizontal & Vertical 176 degree (CR>=10)
Contrast ratio
: 800:1 (Typ.) ,400 :1 (min)
White luminance
: Panel original color >240nits (min), 300 nits (Typ.)
2.2
2.3
2.4
Scanning frequencies
Hor.
Ver.
Video dot rate
Power input
: 30 - 98 K Hz
: 56 - 76 Hz
: 210 MHz
: 90-264 V AC, 50/60 ± 2 Hz
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
4
GENERAL PRODUCT SPECIFICATION
2.5
2.6
2.8
Power consumption
Dimensions
Weight
Functions :
200WP7 LCD
: < 60W maximum with USB
: 483(W) * 402(H) * 235(D) mm
: 8.6Kg
(1)D-SUB analog R/G/B separate inputs, H/V sync separated, Composite (H+V) TTL level, SOG sync
(2)DVI digital Panel Link TMDS input
(3) Audio Signal:
PC line in
2.9
Ambient temperature: 0 ?C - 35 ?C
2.10
Regulatory compliance:
B (Poland), CCC (China), CE (Europe), CSA (Canada), DEMKO (Nordic),
Safety
EZU (Czech), FIMKO (Nordic), Gost (Russia), IEC 950 CB Report, NOM
* Medical compliance only apply for
dedicated models
NYCE (Mexico), PSB (Singapore), SEMKO (Nordic), SISIR CPA
(Singapore), TUV (Germany), UL (USA)
UL2601-1 (NAFTA), EN60601-1-1 (EU) and IEC60601-1 (WW)
EMI
C-tick, CE (Europe), FCC (USA), IC (Canada), VCCI (Japan), BSMI
Ergonomics
E2000, Nutek(Sweden), TCO2003 (T-color) & TCO95 (Black/Silver),
TUV/GS
Compatibility
Windows2000, Windows 98/Me, Windows XP, NSTL
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
5
61
62
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
3.0
Electrical characteristics
3.1
Interface signals
The input signals can be applied in three different modes:
1). D-Sub Analog
Input signal: Video, Hsync. , Vsync
Video: 0.7 Vp-p, input impedance, 75 ohms @DC
Sync. : Separate sync TTL level, input impedance 2.2k ohm terminate
Hsync
Positive/Negative
Vsync
Positive/Negative
Composite sync TTL level, input impedance 5k ohm terminate
(Positive/Negative)
Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive)
2). Intel DVI Digital
Input signal: Single channel TMDS signal
3.2
3.2.1
Interface
D-Sub Cable
Length
: 1.8 M +100/- 0 mm (fixed)
Connector type
: D-Sub male with DDC2B pin assignments.
Blue connector thumb-operated jackscrews
USB hub
Input signal: Upstream input (VBUS, D+, D-, GND) via USB-B receptacle.
Output signal: Downstream output (VBUS, D+, D-, GND) through USB-A receptacle
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
6
GENERAL PRODUCT SPECIFICATION
Pin assignment:
PIN No.
3.2.2
SIGNAL
1
Red
2
Green/ SOG
3
Blue
4
Sense (GND)
5
Cable detect
6
Red GND
7
Green GND
8
Blue GND
9
DDC +5V
10
GND
11
Sense (GND)
12
Bi-directional data
13
H/H+V sync
14
V-sync
15
Data clock
DVI Cable
The input signals are applied to the display through DVI-D cable.
Length
Connector type
: 1.8 M +/- 50 mm (fixed)
: DVI-D male with DDC-2B pin assignments
White connector thumb-operated jackscrews
Pin assignment:
Pin No.
Description
1
TMDS data2-
2
TMDS data2+
3
TMDS data2 shield
4
NC
5
NC
6
DDC clock
7
DDC data
8
Analog V-sync
9
TMDS data1-
10
TMDS data1+
11
TMDS data1 shield
12
NC
13
NC
14
+5V
15
Ground (return for +5V and H/Vsync)
16
Hot plug detect
17
TMDS data0-
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
7
200WP7 LCD
63
64
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
18
3.2.3
TMDS data0+
19
TMDS data0 shield
20
NC
21
NC
22
TMDS clock shield
23
TMDS clock+
24
TMDS clock-
USB Cable (High Full Speed)
Length.
: 1.8 M +/- 50 mm (Max.)
Connector type.
: USB- B Plug (Input)
USB- A Plug (Output)
Pin Assignment:
Pin No.
Description
1
VBUS
2
Data+
3
Data-
4
GND
3.2.5 Software control functions via OSD/control adjustable functions:
(1) PC Analog only Signal Input Mode
Adjustable functions:
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
8
GENERAL PRODUCT SPECIFICATION
Main Menu
Sub Menu
Sub Menu 2
Exit
200WP7 LCD
Description
Default
Default starting point
Brightness & Contrast
Brightness
Sliding bar
100
Contrast
Sliding bar
50
Color
Original
9300K
6500K
6500K
sRGB
User define
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
9
65
66
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
R
Sliding bar
G
Sliding bar
B
Sliding bar
Position
Position
Horizontal
Sliding bar
Vertical
Sliding bar
More Settings
Language
English
Left/right arrow to
English
select
French
German
Italian
Spanish
Russian
Phase
Sliding bar
Phase / Clock
Clock
Sliding bar
OSD setting
OSD position V
OSD position H
Sliding bar
Reset
(2) Digital interface OSD :
Adjustable functions:
1st LEVEL
2nd LEVEL
3rd LEVEL
MONITOR SETUP
Exit
Brightness & Contrast
Brightness
Contrast
Color
Original Color, 9300K,6500K, sRGB, User
Define
Input Selection
Analog(D-Sub), Digital (DVI-D), Analog
(DVI-A)
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
10
GENERAL PRODUCT SPECIFICATION
More Settings
Language
200WP7 LCD
/00,/05 : English, Spanish, French,
German, Italian and Russian
Phase/ Clock
Phase
Clock
OSD Settings
Horizontal
Reset
Vertical
No
Yes
Serial No.:
(Serial No.)
Timing Mode
Up/Down to Move, ok to
Confirm
.
3.3
Timing requirement
3.3.1 Mode storing capacity
1.) Factory preset modes : 15
2.) Preset modes
: 40
3.) User define modes
: 24
3.3.2
Factory preset timings
The factory settings of size and centering are according to the reference timing charts
(See fig-4, fig-5)
MODE NO.
RESOLUTION
1
640 x 350
2
720 x 400
3
640 x 480
4
640 x 480
Dot clock (MHz)
25.175
28.321
25.175
30.24
fh
H-total (us)
H-sync width (us)
H-back porch (us)
H-video width (us)
H-front porch (us)
31.469kHz
31.778(800 dots)
3.813(96 dots)
1.907(48 dots)
25.422(640 dots)
0.636(16 dots)
31.468kHz
31.78(900dots)
3.813(108dots)
1.907(54dots)
25.42(720dots)
0.636(18dots)
31.5kHz
31.778(800 dots)
3.813(96 dots)
1.907(48 dots)
25.422(640 dots)
0.636(16 dots)
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
35 kHz
28.571 (864 dots)
2.116 (64 dots)
3.175(96 dots)
21.164(640 dots)
2.116(64 dots)
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
11
67
68
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
fv
V-total (ms)
V-sync width (ms)
V-back porch (ms)
V-video width (ms)
V-front porch (ms)
SYNC. H/V
POLARITY
SEP. SYNC
70Hz(70.09)
14.27(449 lines)
0.064(2 lines)
1.907(60 lines)
11.12(350 lines)
1.175(37 lines)
+/-
70Hz(70.085)
14.27(449 lines)
0.064(2 lines)
1.112(34 lines)
12.71(400 lines)
0.381(13 lines)
-/+
Y
Y
MODE NO.
RESOLUTION
5
640 x 480
6
800 x 600
Dot clock (MHz)
31.500
60Hz(59.940)
16.683 (525 lines)
0.064 (2 lines)
1.049 (33 lines)
15.253 (480 lines)
0.317 (10 lines)
-/Y
Y
7
800 x 600
36
49.498
37.5kHz
26.667 (840 dots)
2.032 (64 dots)
3.81 (120 dots)
20.317 (640 dots)
0.508 (16 dots)
35.156kHz
28.444(1024 dots)
2.000 (72 dots)
3.556 (128 dots)
22.222(800 dots)
0.666 (24 dots)
37.879kHz
26.4 (1056 dots)
3.2 (128 dots)
2.2 (88 dots)
20 (800 dots)
1 (40 dots)
fv
V-total (ms)
75Hz
13.333 (500 lines)
56.250Hz
17.778 (625 lines)
V-sync width (ms)
V-back porch (ms)
V-video width (ms)
V-front porch (ms)
SYNC. H/V
POLARITY
SEP. SYNC
0.08 (3 lines)
0.427 (16 lines)
12.8 (480 lines)
0.026 (1 line)
-/-
0.057 (2 lines)
0.626 (22 lines)
17.066 (600 lines)
0.029
(1 line)
+/+
60.317Hz
16.579 (628
lines)
0.106 (4 lines)
0.607 (23 lines)
15.84 (600lines)
0.026 (1 line)
+/+
MODE NO.
RESOLUTION
9
1024 x 768
Dot clock (MHz)
0.064 (3 lines)
0.448 (21 lines)
12.8 (600 lines)
0.021 (1 line)
+/+
Y
10
1024 x 768
11
1152 x 870
12
1280 x 1024
100
108
78.75
48.363kHz
20.677(1344 dots)
60.023kHz
16.66 (1312dots)
H-sync width (us)
H-back porch (us)
H-video width (us)
2.092(136 dots)
2.462(160 dots)
15.754(1024 dots)
1.219 (96 dots)
2.235 (176 dots)
13.003 (1024 dots)
H-front porch (us)
0.369(24 dots)
0.203 (16 dots)
fv
V-total (ms)
60.004Hz
16.666(806 lines)
75Hz (75.000)
13.328 (800 lines)
V-sync width (ms)
V-back porch (ms)
V-video width (ms)
0.124(6 lines)
0.600(29 lines)
15.880(768 lines)
0.05(3 lines)
0.446 (28 lines)
12.80 (768 lines)
V-front porch (ms)
SYNC. H/V
POLARITY
0.062(3 lines)
-/-
0.017 (1 line)
+/+
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
68.7kHz
14.56 (1456
dots)
1.28 (128 dots)
1.44(144 dots)
11.52 (1152
dots)
0.32 (32 dots)
75Hz
13.333 (916
lines)
0.044 (3 lines)
0.568(39 lines)
12.678 (870
lines)
0.043 (4 line)
-/-
63.981kHz
15.63 (1688 dots)
1.037 (112 dots)
2.296 (248 dots)
11.852 (1280 dots)
0.445 (48 dots)
60.020Hz
16.661 (1066 lines)
0.047 (3 lines)
0.594 (38 lines)
16.005 (1024 lines)
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
75Hz
13.333 (625 lines)
Y
fh
H-total (us)
2006-02-16
Jason Wang
46.875kHz
21.333 (1056 dots)
1.616 (80 dots)
3.232 (160 dots)
16.162 (800 dots)
0.323 (16 dots)
Y
65
TYPE
8
800 x 600
40
fh
H-total (us)
H-sync width (us)
H-back porch (us)
H-video width (us)
H-front porch (us)
Y
67Hz
15 (525 lines)
0.086(3 lines)
1.114(39 lines)
13.714(480 lines)
0.086(3 lines)
-/-
590
12
0.015 (1 line)
+/+
GENERAL PRODUCT SPECIFICATION
SEP. SYNC
Y
Y
Y
Y
MODE NO.
RESOLUTION
13
1280 x 1024
14
1600 x 1200
15
1680 x 1050
Dot clock (MHz)
135
162
146.249
f h (kHz)
H-total (us)
H-sync width (us)
H-back porch (us)
H-video width (us)
H-front porch (us)
79.976kHz
12.504(1688 dots)
1.067(144 dots)
1.837(248 dots)
9.481(1280 dots)
0.119(16 dots)
75
13.333(2160 dots)
1.185(192 dots)
1.877(304 dots)
9.877(1600 dots)
0.395(64 dots)
65.29
15.316(2240 dots)
1.203(176 dots)
1.915(280 dots)
11.487(1680 dots)
0.711(104 dots)
f v (Hz)
V-total (ms)
V-sync width (ms)
V-back porch (ms)
V-video width (ms)
V-front porch (ms)
SYNC. H/V
POLARITY
SEP. SYNC
75.025Hz
13.329(1066 lines)
0.038(3 lines)
0.475(38 lines)
12.804(1024 lines)
0.012 (1 line)
+/+
60.000
16.667(1250 lines)
0.040(3 lines)
0.613(46 lines)
16.000(1200 lines)
0.013(1 lines)
+/+
59.954
16.679(1089 lines)
0.092(6 lines)
0.459(30 lines)
16.082(1050 lines)
0.046(3 lines)
+/+
Y
Y
Y
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
13
200WP7 LCD
69
70
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
3.3.3
Horizontal scanning
Sync polarity
Scanning frequency
: Positive or Negative
: 30 - 98 K Hz
3.3.4 Vertical scanning
Sync polarity
Scanning frequency
: Positive or Negative
: 56 - 76 Hz
3.4
Power input connection
Power cord length
: 1.8 M
Power cord type
: 3 leads power cord with
protective earth plug.
3.5
Power management
The monitor must comply with the Microsoft On Now specification, with two
power management states, as defined by the VESA DPMS document. The monitor
Mode
HSYNC
VSYNC
Video
Pwr-cons.
Indication
Rec. time
Power-On
On
On
active
< 60 W
Green LED
With USB
Power-On
On
On
active
< 48 W
Green LED
Without USB
Off
Off
On
blanked
<2W
Amber LED
<3s
Off
On
Off
blanked
<2 W
Amber LED
<3s
Off
Off
Off
blanked
<2W
Amber LED
<3s
N/A
< 1W
LED Off
DC Power Off
3.6
Display identification
3.6.1 In accordance with VESA Display Channel Standard Ver.1.0 and
having DDC 2B capability
3.6.2
In accordance with DVI requirement (DDWG digital Visual Interface revision 1.0)
use DDC 2B and EDID 3.0 structure 2.0
4.0
Visual characteristics
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
14
GENERAL PRODUCT SPECIFICATION
4.1
200WP7 LCD
Test conditions
Unless otherwise specified, this specification is defined
under the following conditions.
(1) Input signal
: As defined in 3.3, 1600x 1200
non-interlaced mode (75K/60Hz), signal
sources must have 75 ohm output impedance.
(2) Luminance setting: controls to be set to 200 nits with
full screen 70 % duty cycle white signal
(3) Warm up: more than 30 minutes after power on with signal supplied.
(4) Ambient light: 400 -- 600 lux.
(5) Ambient temperature: 20 +/- 5 °C
4.2
Resolution:
Factory preset modes (15 modes)
Item
H.Freq.
Mode
Resolution
(KHz)
V.Freq.
Item
(Hz)
H.Freq.
Mode
(KHz)
Resolutio
V.Freq
n
. (Hz)
1
31.469
IBM VGA 10H
640x350
70.086
9
48.363
VESA
1024x768
60.004
2
31.469
IBM VGA 3H
720x400
70.087
10
60.023
VESA
1024x768
75.029
3
31.469
IBM VGA 12H
640x480
59.940
11
68.700
MACINTOSH
1152x870
75.000
4
35.000
MACINTOSH
640x480
67.000
12
63.981
VESA
1280x102
60.020
4
5
37.500
VESA
640x480
75.000
13
79.976
VESA
1280x102
75.025
4
6
35.156
VESA
800x600
56.250
14
75.0
VESA
1600x120
60
0
7
37.879
VESA
800x600
60.317
15
65.29
-
1680x105
0
8
46.875
VESA
800x600
75.000
Note: 1. Screen displays at 40 preset modes
2. Screen displays perfect picture at 15 factory-preset modes
3. Screen displays visible picture with OSD warning when input modes
are other then 22 preset modes
4.3
Brightness: >=300 nits (at panel color temperature, at center of the screen, set contrast
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
15
60.0
71
72
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
and brightness at maximum. )
4.4
4.4.1
Image size
Actual display size
433.44 x 270.9mm
4.5
Brightness uniformity
Set contrast at 100% and turn the brightness to get average above 250 nits (LPL),
nits (AUO) nits at centre of the screen.
Apply the Fig 1; it should comply with the following formula:
Minimum luminance of nine points (brightness)
X100% (Min.)
Maximum luminance of nine points (brightness)
LM201W01-SLA1 (LPL)-----70% (min.)
M201EW01 v0 (AUO)-----70% (min.), 75% (typ.)
4.6
Check Cross talk (S)
Apply Pattern 2. Set contrast and brightness at 100 %.
Measure YA. Then output Pattern 3 and measure YB.
the cross talk value :
ABS (YA - YB)
¾¾¾¾¾¾¾¾¾ X 100%
YA
LM201W01-SLA1 (LPL)-----1.8% (max)
M201EW01 v0 (AUO)----- 1.5% (max.)
4.7
White color adjustment
There are three factory preset white color 9300K, 6500K, sRGB.
Apply full gray64 pattern, with brightness in 100 % position
and the contrast control at 50 % position.
The 1931 CIE Chromaticity (color triangle) diagram (x,y)
coordinate for the screen center should be:
9300K CIE coordinates
X = 0.283 +/- 0.020
Y = 0.297 +/- 0.020
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
16
and 240
GENERAL PRODUCT SPECIFICATION
6500K/ sRGB CIE coordinates
X = 0.313 +/- 0.020
Y = 0.329 +/- 0.020
5.0
Mechanical characteristics
5.1
Controls
Front side:
- DC power switch
- OSD function key (OK)
- UP
- DOWN
- RIGHT
- LEFT
- AUTO
Rear:
- D-SUB
- DVI-D
- Power cord socket
5.2
Unit dimension / Weight
Set dimension (incl. pedestal): 483(W) * 402(H) * 235(D) mm
Net weight
5.3
: 8.6Kg (Including I/F cable 240 g)
Tilt and swivel base
Tilt angle
:
Swivel angle :
5.4
-5 ° to +25 °
+/- 45 °
Transportation packages
5.4.1 Shipping dimension/Weight
Carton dimension
: 579(W) X 267(H) X 513(D) mm
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
17
200WP7 LCD
73
74
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
Gross weight
: 10.7 KG
5.4.2 Block unit / Palletization
sets/ layer
4
layers/ block
8
sets/ block unit
32
6.0
Environmental characteristics
The following sections define the interference and
susceptibility condition limits that might occur
between external environment and the display device.
6.1
Susceptibility of display to external environment
Operating
- Temperature : 0 to 40 degree C
- Humidity
: 80% max
- Altitude
: 0-3658m
- Air pressure : 600-1100 mBAR
Storage
- Temperature : -20 to 60 degree C
- Humidity
: 95% max ( < 40 )
- Altitude
: 0-12192m
- Air pressure
: 300-1100 mBAR
Note: recommend at 5 to 35°C, Humidity less than 60 %
6.2
6.3
Transportation tests
Standard
Philips UAN-D1400
76.2cm(1~9.52kg)
61 cm (9.53~18.59kg)
1 corner
Sequence
3 faces
After -100C
Electrical function ok
Test
Mechanical function ok
Result
No serious damage on set appearance
(Room temp. /-10° c, humidity 70 %)
Packaging:
5-200 Hz
Sequence
0.73 G
30 min. for each axis
Electrical function ok
Test
Mechanical function ok
Result
No serious damage on set appearance
For design evaluation only
Operating
NSTA
76.2cm(1~9.52kg)
61 cm (9.53~18.59kg)
1 corner
3 edge
6 face
Height
Drop
Test
Vibration
Test
Shock
Test
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
Operating:
10-50-10 Hz
0.35 mm
30 min. for each axis
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
18
GENERAL PRODUCT SPECIFICATION
test
30 G,
16 m-sec, 6 cycles
Temperature :
23
Humidity
: 60 %
Air pressure : 100 kpa
(According to DSD draft standard UAN-D636)
6.3
Display disturbances from external environment
According to IEC 801-2 for ESD disturbances
6.4
Display disturbances to external environment
6.4.1 EMI
EMI
: C-tick, CE(Europe), FCC(USA), IC(Canada), VCCI(Japan), BSMI
7.0
Reliability
7.1
Mean Time Between Failures
System MTBF (Excluding the LCD panel and CCFL): 50,000 hrs
CCFL MTBF: 40,000 hrs
8.0
8.1
Quality assurance requirements
Acceptance test
According to MIL-STD-105D
Control II level
AQL: 0.65 (major)
2.50 (minor)
(Please also refer to annual quality agreement)
Customer acceptance criteria: UAW0377/00
9.0
Serviceability
The serviceability of this monitor should fulfill the
requirements which are prescribed in UAW-0346 and must
be checked with the check list UAT-0361.
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
19
200WP7 LCD
75
76
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
10. LCD PANEL CHARACTERISTICS REQUIREMENTS
LCD Panel Pixel Defect Requirement
Acceptable Level
Bright Dot Defects
1 lit subpixel
3
2 adjacent lit subpixels
1
3 adjacent lit subpixels (one white pixel)
0
Distance between two bright dot defects
25mm or more
Bright dot defects within 20mm circle
3 or fewer
Total bright dot defects of all types
3
Dark Dot Defects
1 dark subpixel
5
2 adjacent dark subpixels
2
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
20
GENERAL PRODUCT SPECIFICATION
3 adjacent dark subpixels (one white pixel)
1
Distance between two black dot defects
15mm or more
Total black dot defects of all types
5
Total bright or black dot defects of all types
5
*Note: 1 or 2 adjacent subpixel defects= 1 dot defect
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
21
200WP7 LCD
77
78
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
Fig 1: Brightness Uniformity
L/2
L/10
L
W/10
1
2
3
4
5
6
W
W/2
7
8
9
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
22
GENERAL PRODUCT SPECIFICATION
Fig 2:
200WP7 LCD
Cross talk pattern
Gray level 46 (64 Gray level)
1/6
1/2
YA
1/2
Fig 3: Cross-talk Pattern
Center at Gray level 0 (Black)
1/3
1/3
1/6
1/3
1/2
1/3
YB
1/2
1/3
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
23
79
80
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
SEPARATE SYNC.
VIDEO
D
C
E
HORIZONTAL
B
A
VIDEO
R
Q
S
VERTICAL
P
O
COMPOSITE SYNC.
VIDEO
C
D
E
HORIZONTAL
B
A
FIG-4 TIMING CHART -1
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
TYPE
2006-02-16
Jason Wang
8639 000 16908
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
24
GENERAL PRODUCT SPECIFICATION
200WP7 LCD
VIDEO
Q
R
S
VERTICAL
P
O
COMPOSITE SYNC. & VIDEO
( SYNC. ON GREEN )
HORIZONTAL
B
C
E
D
A
VERTICAL
B
S
P
Q
R
O
FIG-5 TIMING CHART -2
20.1" TFT UXGA LCD Monitor
(HUDSON 7-200WP7)
2006-02-16
Jason Wang
8639 000 16908
TYPE
: 200WP7ES/00
BRAND : PHILIPS
25
2006-02-16
590
25
81
82
200WP7 LCD
Go to cover page
0004
0030
0031
0032
0033
0040
0041
0042
0043
0051
313815761011
313815761221
313815418091
313815417771
313815417781
313815761001
313815417791
313815417811
313815133511
313815138241
SUPER ERGO BASE ASSY
BEZEL ASSY-SILVER
BEZEL-SLIVER
BEZEL- DECO
CONTROL KNOB
BACK COVER ASSY-S
BACK COVER
MIDDLE COVER-SILVER
VESA PLATE
METAL FRAME
7201
7202
7351
7351
7353
7353
7401
7403
7405
7501
7502
7503
7504
7505
7506
7507
7508
7509
932214526668
932214526668
313815867291
932222343682
313815867301
932214725682
823827737015
932220099685
932216733668
933769900215
933769900215
932217440685
932216638668
932216638668
932217440685
932216733668
932216638668
932217440685
IC SM M24C02-WMN6 (ST00) R
IC SM M24C02-WMN6 (ST00) R
CPU IC ASSY
IC SM NT68F631ALG (NOVA) L
EEPROM IC ASSY
IC M24C16-WBN6P
(ST00) L
SCALER IC NT68563HFG
IC SM LD1117AS18
(ST00) R
IC SM LD1117S33
(ST00) R
TRA SIG SM BC857C (PHSE) R
TRA SIG SM BC857C (PHSE) R
TRA SIG SM KRC102S (KEC0) R
FET POW SM SI5441DC-E3 (VISH)R
FET POW SM SI5441DC-E3 (VISH)R
TRA SIG SM KRC102S (KEC0) R
IC SM LD1117S33
(ST00) R
FET POW SM SI5441DC-E3 (VISH)R
TRA SIG SM KRC102S (KEC0) R
7622
7625
7631
7651
7671
7675
932217440685
932216638668
932222352668
932222162671
932222269668
932222269668
TRA SIG SM KRC102S (KEC0) R
FET POW SM SI5441DC-E3 (VISH)R
IC SM TPS54357PWP (TI00) R
IC SM CY7C65640-LFXC (CYPR) Y
IC SM TPS2062DG4
(TI00) R
IC SM TPS2062DG4
(TI00) R
Recommended Parts List
200WP7 LCD
Model:200WP7ES/00(AUO Panel)
Mechanical Parts
0004 313815761011 SUPER ERGO BASE ASSY
0030 313815761221 BEZEL ASSY-SILVER
0031 313815418091 BEZEL-SLIVER
0032 313815417771 BEZEL- DECO
0033 313815417781 CONTROL KNOB
0040 313815761001 BACK COVER ASSY-S
0041 313815417791 BACK COVER
0042 313815417811 MIDDLE COVER-SILVER
0043 313815133511 VESA PLATE
0051 313815138241 METAL FRAME
0053 313815321301 INSULATE PLATE
0080 313815759083 SHIELDING ASSY
0090 313815136711 AC PLATE
0095 313815136721 DSUB PLATE
0126 313815569471 RATING LABEL
0280 313800991971 PROCESS BOX
0290 313800992071 PROCESS BOX
0340 313815136703 SHIELDING
0341 313815421312 INSULATING PLATE
0502 313815641931 SLEEVE
1057 313815867411 FRAME+WIRE ASSY
LCD Panel
1050 823827720701 TFT-LCD MOD M201EW01 V.0 A
Packing
0129 313810632613
0450 313815642281
0451 313815642231
0452 313815642241
0453 313815641821
0508 313815642281
PE BAG
CARTON-200WP
CUSHION - TOP
CUSHION - BUTTON
P.E. BAG
CARTON-200WP
Accessory
0141 313815524341
0602 313811709411
1056 823827732068
1060 313819871431
1061 313818870471
1063 313819872531
1064 313819871471
QUICK SETUP GUIDE-200WP
E-D.F.U.
CBLE-130 30/115/30 334033AWG28
CORD SUB-D 15/1M8/15 D-SUB BK
MAINSCORD IEC 10A 1M8 DET BK
CORD USB A/1M8/USB B BK
CORD DVI 18+1/1M8/DVI 18+1 BK
PCB ASSY
1051 313815867281
1052 313815865861
1054 313815867111
1055 823827732047
SCALER ASSY-200WP7 AUO
CONTROL ASSY
USB ASSY(200 WP7)
PSU OPENFR IPS60W(EADP-57BFAA
Miscellanea
0138 313815555711
0280 313800991971
0291 313815569531
0292 313815569531
0615 313811709541
1098 243803100435
1201 242203300521
1202 242202518053
1351 243854300079
1352 242202518947
1354 242202518947
1401 242202518804
1501 242202518825
1505 242202518824
1601 242202518896
1608 823827732071
1609 823827732069
1610 243854300085
1651 242202518953
1652 242202518955
1653 242202518957
1654 242202518953
1951 243812800196
1952 243812800196
1953 243812800196
1954 243812800196
1955 243812800196
1956 243812800196
1957 243812800196
1960 243812800196
1961 242202518897
4444 313810610503
4444 313810610504
8061 823827732072
HI-POT LABEL
PROCESS BOX
LABEL
LABEL
HEX CODE OF F/W(NO MATE REQ)
SOC IC V 8P F 2.54 DIL
L
SOC DVI H 24P F 1.91DVI-D Y
SOC SUBD H 15P F BU 1216 B
RES XTL SM 12MHZ 32P SMD-49 R
CON V 4P M 2.50
64834 B
CON V 4P M 2.50
64834 B
CON V 30P M 1.25 SM 60948 R
63393 B
CON V 13P M 2.00
CON V 11P M 2.00
63391 B
CON H 6P M 2.00
63366 B
CABLE RING TERM/45/FAST AWG18
CABLE RING TERM/85/FAST AWG18
RES XTL SM 24MHZ 20P SMD-49 R
SOC USB V 4P F 2.0/2.5 5401 Y
SOC USB V 4P F 2.5
5411 Y
SOC USB V 8P F 2.0/2.5 5402 R
SOC USB V 4P F 2.0/2.5 5401 Y
SWI TACT H=5 GY 160G SKHHAM B
SWI TACT H=5 GY 160G SKHHAM B
SWI TACT H=5 GY 160G SKHHAM B
SWI TACT H=5 GY 160G SKHHAM B
SWI TACT H=5 GY 160G SKHHAM B
SWI TACT H=5 GY 160G SKHHAM B
SWI TACT H=5 GY 160G SKHHAM B
SWI TACT H=5 GY 160G SKHHAM B
CON H 7P M 2.00
63367 B
CD ROM - SERVICE MANUAL
SERVICE MANUAL
CBLE-023 13/390/7+6-017-016
PCB ASSY
1051 313815867281 SCALER ASSY-200WP7 AUO
2201
2202
2203
2204
2205
2214
2215
2216
2217
2218
2219
2221
2222
2224
2225
2227
2228
2229
2241
2351
2353
2354
2356
2358
2359
2360
2361
2364
2401
2402
2404
2406
2413
2414
2416
2417
2419
2420
2422
2423
2424
2425
2427
2428
2431
2443
2444
2446
2451
2452
2455
2457
2458
2459
2501
2502
2503
2504
2505
2506
2510
2511
2515
2516
2517
2518
2519
2520
2521
2522
2523
2524
2525
2526
2527
2529
2530
2531
223878615649
223878615649
223886715331
223886715331
223878615649
223878615649
223886715331
223886715331
223886715339
223886715221
223878615649
223878615645
223878615645
223878615645
223878615645
223878615645
223878615645
223878615649
223878615645
223878615649
223886715229
223886715229
223878615649
223886715101
823827736009
223878615649
223886715101
223886715229
202203100205
223878615649
223878615649
223878615649
202203100205
223878615649
223878615649
223878615649
223878615649
823827736009
223878615649
823827736009
223878615649
202203100205
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
823827736009
223878615649
823827736009
223878615649
223878615649
223878615649
202203100205
223878615649
223878615649
202203100205
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615645
202203100205
223878615649
223878615649
223878615645
202203100205
223878615645
202203100205
823827736009
223878615649
823827736009
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER1 0603 NP0 50V 330P PM5 R
CER1 0603 NP0 50V 330P PM5 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER1 0603 NP0 50V 330P PM5 R
CER1 0603 NP0 50V 330P PM5 R
CER1 0603 NP0 50V 33P PM5 R
CER1 0603 NP0 50V 220P PM5 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 47N PM10 R
CER2 0603 X7R 16V 47N PM10 R
CER2 0603 X7R 16V 47N PM10 R
CER2 0603 X7R 16V 47N PM10 R
CER2 0603 X7R 16V 47N PM10 R
CER2 0603 X7R 16V 47N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 47N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER1 0603 NP0 50V 22P PM5 R
CER1 0603 NP0 50V 22P PM5 R
CER2 0603 X7R 16V 100N PM10 R
CER1 0603 NP0 50V 100P PM5 R
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10 R
CER1 0603 NP0 50V 100P PM5 R
CER1 0603 NP0 50V 22P PM5 R
ELCAP SM RVS 25V 47U PM20 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
ELCAP SM RVS 25V 47U PM20 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10 R
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10 R
ELCAP SM RVS 25V 47U PM20 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10 R
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
ELCAP SM RVS 25V 47U PM20 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
ELCAP SM RVS 25V 47U PM20 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 47N PM10 R
ELCAP SM RVS 25V 47U PM20 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 47N PM10 R
ELCAP SM RVS 25V 47U PM20 R
CER2 0603 X7R 16V 47N PM10 R
ELCAP SM RVS 25V 47U PM20 R
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10 R
CHIP 4.7UF 25V X7R 1206
3201
3202
3203
232270260103 RST SM 0603 RC21 10K PM5 R
212211805656 RST SM 0603 RC0603 1K PM5 R
212211805656 RST SM 0603 RC0603 1K PM5 R
3207
3208
3209
3210
3211
3212
3213
3214
3229
3230
3231
3233
3234
3235
3236
3237
3238
3239
3240
3241
3242
3243
3244
3247
3248
3249
3251
3252
3253
3254
3255
3256
3258
3259
3261
3262
3263
3351
3353
3354
3359
3368
3369
3370
3371
3372
3373
3374
3375
3379
3391
3392
3401
3413
3416
3419
3501
3502
3503
3504
3506
3507
3508
3509
3510
3511
3512
3515
3516
3517
3518
3519
3520
3521
3522
3523
3524
3525
3526
3527
3528
3529
3534
3537
232270260103
232270260103
232270260103
232270260223
232270260101
232270260101
232270260101
232270260101
232270260103
232270260103
232270260759
232270260103
232270260223
232270260101
232270260101
232270260101
232270260101
232270260101
232270260101
212211805661
212211805661
212211805964
232270260759
232270260471
212211805964
232270260759
232270260759
232270260759
212211805964
232270260759
212211805656
232270260103
232270260223
232270260223
232270296001
232270296001
232270296001
212211805689
232270260103
232270260101
232270260101
232270260101
232270260101
232270260103
232270260103
232270260103
232270260101
232270260101
232270260101
232270260101
232270296001
232270296001
232270463901
232270260103
232270260101
232270260101
232270260479
232270260479
232270260479
232270260103
232270260101
232270260101
232270260101
232270260221
232270260103
232270260221
232270260103
232270260103
232270260103
212211805683
232270260103
232270260103
232270260103
212211805683
232270260103
232270260223
232270260103
232270260103
232270260103
232270260103
212211805683
232270260103
232270296001
232270296001
83
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 22K PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 75R PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 22K PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC0603 2K2 PM5 R
RST SM 0603 RC0603 2K2 PM5 R
RST SM 0603 RC0603 75R PM1 R
RST SM 0603 RC21 75R PM5 R
RST SM 0603 RC21 470R PM5 R
RST SM 0603 RC0603 75R PM1 R
RST SM 0603 RC21 75R PM5 R
RST SM 0603 RC21 75R PM5 R
RST SM 0603 RC21 75R PM5 R
RST SM 0603 RC0603 75R PM1 R
RST SM 0603 RC21 75R PM5 R
RST SM 0603 RC0603 1K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 22K PM5 R
RST SM 0603 RC21 22K PM5 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 RC0603 1M PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 RC22H 390R PM1 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 47R PM5 R
RST SM 0603 RC21 47R PM5 R
RST SM 0603 RC21 47R PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 220R PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 220R PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC0603 100K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC0603 100K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 22K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC0603 100K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 JUMP. MAX 0R05 R
84
200WP7 LCD
Go to cover page
3540
232270296001 RST SM 0603 JUMP. MAX 0R05 R
5201
5202
5204
5351
5401
5402
5403
5407
5409
5410
5413
5501
5502
242254944196
242254944196
242254944196
242254944196
242254944196
242254944196
242254944196
242254944196
242254944196
242254900113
242254945579
242254945579
242254945579
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0603 EMI 100MHZ 1K R
IND FXD 1206 EMI 100MHZ 100R R
IND FXD 1206 EMI 100MHZ 100R R
IND FXD 1206 EMI 100MHZ 100R R
6201
6202
6203
6204
6401
6402
6403
933913910115
933913910115
933913910115
933913910115
932220675682
932220675682
932220628682
DIO SIG SM BAS32L (PHSE) R
DIO SIG SM BAS32L (PHSE) R
DIO SIG SM BAS32L (PHSE) R
DIO SIG SM BAS32L (PHSE) R
DIO REC M100AL-5301-E3 (VISH)B
DIO REC M100AL-5301-E3 (VISH)B
DIO REC SB140AL-5301E3 (VISH)B
7201
7202
7351
7351
7353
7353
7401
7403
7405
7501
7502
7503
7504
7505
7506
7507
7508
7509
932214526668
932214526668
313815867291
932222343682
313815867301
932214725682
823827737015
932220099685
932216733668
933769900215
933769900215
932217440685
932216638668
932216638668
932217440685
932216733668
932216638668
932217440685
IC SM M24C02-WMN6 (ST00) R
IC SM M24C02-WMN6 (ST00) R
CPU IC ASSY
IC SM NT68F631ALG (NOVA) L
EEPROM IC ASSY
IC M24C16-WBN6P
(ST00) L
SCALER IC NT68563HFG
IC SM LD1117AS18
(ST00) R
IC SM LD1117S33
(ST00) R
TRA SIG SM BC857C (PHSE) R
TRA SIG SM BC857C (PHSE) R
TRA SIG SM KRC102S (KEC0) R
FET POW SM SI5441DC-E3 (VISH)R
FET POW SM SI5441DC-E3 (VISH)R
TRA SIG SM KRC102S (KEC0) R
IC SM LD1117S33
(ST00) R
FET POW SM SI5441DC-E3 (VISH)R
TRA SIG SM KRC102S (KEC0) R
1052
313815865861 CONTROL ASSY
2951
2952
223858619812 CER2 0603 Y5V 50V 100N P8020 R
223858619812 CER2 0603 Y5V 50V 100N P8020 R
3951
3952
3953
3954
3955
3956
3957
232270260101
232270260473
232270260103
212211805656
232270260473
232270260103
212211805656
6951
932214603682 LED VS L-3WYGW
1054
313815867111 USB ASSY(200 WP7)
2601
2603
2604
2621
2623
2625
2631
2633
2634
2635
2636
2651
2652
2655
2656
2661
2662
2665
2666
2671
2675
2680
2681
2682
223878615649
202203100179
223858619812
223878615649
223858615636
222224119876
202202000963
223878615649
202202000963
223878615643
222278015663
202001293803
223878615649
202001293803
223878615649
202001293803
223878615649
202001293803
223878615649
223878615649
223878615649
223878615649
223878615649
223886715279
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC21 47K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC0603 1K PM5 R
RST SM 0603 RC21 47K PM5 R
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC0603 1K PM5 R
(KIEL) B
CER2 0603 X7R 16V 100N PM10 R
ELCAP SM HV 25V 10U PM20 R
CER2 0603 Y5V 50V 100N P8020 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 50V 10N PM10 R
CER2 1206 Y5V 10V 10U P8020 R
ELCAP SM LV 25V 100U PM20 R
CER2 0603 X7R 16V 100N PM10 R
ELCAP SM LV 25V 100U PM20 R
CER2 0603 X7R 16V 33N PM10 R
CER2 0805 X7R 16V 1U PM10 R
ELCAP SM RV2 16V 100U PM20 R
CER2 0603 X7R 16V 100N PM10 R
ELCAP SM RV2 16V 100U PM20 R
CER2 0603 X7R 16V 100N PM10 R
ELCAP SM RV2 16V 100U PM20 R
CER2 0603 X7R 16V 100N PM10 R
ELCAP SM RV2 16V 100U PM20 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER2 0603 X7R 16V 100N PM10 R
CER1 0603 NP0 50V 27P PM5 R
2683
2684
2685
2691
2692
2693
2694
2695
2696
2697
2698
2699
223886715279
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
CER1 0603 NP0 50V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
27P PM5 R
100N PM10 R
100N PM10 R
100N PM10 R
100N PM10 R
100N PM10 R
100N PM10 R
100N PM10 R
100N PM10 R
100N PM10 R
100N PM10 R
100N PM10 R
3622
3623
3634
3681
3682
3683
3685
3687
3689
3691
3692
3693
4631
232270260103
212211805683
232270260202
212211805672
212211805683
212211805672
212211805672
212211805672
212211805672
212211805672
212211805672
212211805672
232270296001
RST SM 0603 RC21 10K PM5 R
RST SM 0603 RC0603 100K PM5 R
RST SM 0603 RC21 2K PM5 R
RST SM 0603 RC0603 15K PM5 R
RST SM 0603 RC0603 100K PM5 R
RST SM 0603 RC0603 15K PM5 R
RST SM 0603 RC0603 15K PM5 R
RST SM 0603 RC0603 15K PM5 R
RST SM 0603 RC0603 15K PM5 R
RST SM 0603 RC0603 15K PM5 R
RST SM 0603 RC0603 15K PM5 R
RST SM 0603 RC0603 15K PM5 R
RST SM 0603 JUMP. MAX 0R05 R
5601
5602
5603
5621
5622
5634
5651
5653
5655
5657
5659
242254900126
242254900126
242254900126
242254900126
242254900126
313818875771
242254900126
242254900126
242254900126
242254900126
242254900126
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
COI CHOKE 35UH 82M OHM DR10X8
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
IND FXD 0805 EMI 100MHZ 120R R
6634
6635
6662
932221745685 DIO REC SM SSA34-E3 (VISH) R
932221745685 DIO REC SM SSA34-E3 (VISH) R
933913910115 DIO SIG SM BAS32L (PHSE) R
7622
7625
7631
7651
7671
7675
932217440685
932216638668
932222352668
932222162671
932222269668
932222269668
TRA SIG SM KRC102S (KEC0) R
FET POW SM SI5441DC-E3 (VISH)R
IC SM TPS54357PWP (TI00) R
IC SM CY7C65640-LFXC (CYPR) Y
IC SM TPS2062DG4
(TI00) R
IC SM TPS2062DG4
(TI00) R
According to the ECO CA005895,the panel has been replaced
by MOD M201EW01 V.3 ,the updated parts as below:
Action
From
To
New
Del
Item
12NC
Description
1050 823827720701 TFT-LCD MOD M201EW01 V.0 A
1050 823827720911 TFT-LCD MOD M201EW01 V.3
3533 212211805631 RST SM 0603 JUMP. MAX 0R05 R
232270296001 RST SM 0603 JUMP. MAX 0R05 R
3537 212211805631 RST SM 0603 JUMP. MAX 0R05 R
232270296001 RST SM 0603 JUMP. MAX 0R05 R
Spare Parts List
Model:200WP7ES/01(LPL Panel) 12NC: 8639 000 17096
Mechanical Parts
4
30
31
32
33
40
41
42
43
44
51
80
116
340
450
1057
313815761011
313815761221
313815418091
313815417771
313815417781
313815761001
313815417791
313815417811
313815133511
313815162071
313815138241
313815759083
313810440571
313815136703
313815642281
313815867411
SUPER ERGO BASE ASSY
BEZEL ASSY-SILVER
BEZEL-SLIVER
BEZEL- DECO
CONTROL KNOB
BACK COVER ASSY-S
BACK COVER
MIDDLE COVER-SILVER
VESA PLATE
CONTACT SPRING
METAL FRAME
SHIELDING ASSY
HOUSING COVER
SHIELDING
CARTON-200WP
FRAME+WIRE ASSY
Packing Parts
450
451
452
453
313815642281
313815642231
313815642241
313815641821
CARTON-200WP
CUSHION - TOP
CUSHION - BUTTON
P.E. BAG
Accessory
602
1060
1061
1063
1064
313811709571
313818873992
313818870471
313819872531
313819871471
E-D.F.U.
CORD SUB-D 15/1M8/15 SUB-D M/
MAINSCORD IEC 10A 1M8 DET B
CORD USB A/1M8/USB B BK
CORD DVI 18+1/1M8/DVI 18+1 BK
miscellanea
341 313815421312
1056 823827732068
8061 823827732072
INSULATING PLATE
CBLE-130 30/115/30 334033AWG2
CBLE-023 13/390/7+6-017-016
LCD Panel
1050 823827718711
LCD LM201W01-SLA1
PCB Assy
1051
1052
1054
1055
313815865851
313815865861
313815867111
823827732047
SCALER ASSY(200WP7)
CONTROL ASSY
USB ASSY(200 WP7)
PSU OPENFR IPS60W(EADP-57BFA
PCB Assy
1051 313815865851
various
291 313815569901
292 313815569901
615 313811709701
1098 243803100435
1099 243803100437
1201 242203300521
1202 242202518053
1351 243854300079
1352 242202518947
1401 243854300093
1402 242202518804
1501 242202518825
1505 242202518824
LABEL
LABEL
HEX CODE OF F/W(NO MATL REQ)
SOC IC V 8P F 2.54 DIL
SOC IC V 44P F 1.27 PLCC
SOC DVI H 24P F 1.91DVI-D
SOC SUBD H 15P F BU 1216
RES XTL SM 12MHZ 32P SMD-49
CON V 4P M 2.50
64834
RES XTL SM 14M3181 18P SMD49
CON V 30P M 1.25 SM 60948
CON V 13P M 2.00
63393
63391
CON V 11P M 2.00
2201
2202
2203
2204
2205
2214
2215
2216
2217
2218
2219
2221
2222
2224
2225
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER1 0603 NP0 50V
CER1 0603 NP0 50V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER1 0603 NP0 50V
CER1 0603 NP0 50V
CER1 0603 NP0 50V
CER1 0603 NP0 50V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
CER2 0603 X7R 50V
CER2 0603 X7R 16V
CER2 0603 X7R 16V
223878615649
223878615649
223886715331
223886715331
223878615649
223878615649
223886715331
223886715331
223886715339
223886715221
223878615649
223878615645
223858615623
223878615645
223878615645
SCALER ASSY(200WP7)
100N PM10
100N PM10
330P PM5
330P PM5
100N PM10
100N PM10
330P PM5
330P PM5
33P PM5
220P PM5
100N PM10
47N PM10
1N PM10
47N PM10
47N PM10
2227
2228
2229
2241
2302
2303
2304
2305
2306
2307
2308
2309
2310
2311
2312
2313
2314
2315
2316
2317
2318
2319
2320
2321
2322
2323
2324
2325
2326
2327
2328
2329
2330
2332
2333
2334
2351
2353
2354
2356
2358
2359
2360
2361
2401
2402
2403
2404
2405
2406
2407
2408
2409
2410
2411
2412
2413
2414
2415
2416
2417
2419
2420
2421
2422
2423
2424
2425
2426
2427
2428
2429
2430
2431
2432
2433
2434
2435
2436
2437
2438
2439
2440
2441
2442
223878615645
223878615645
223878615649
223878615645
223878615649
202203100198
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
202203100198
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223858615636
823827736009
823827736009
223878615649
223878615649
223886715229
223886715229
223878615649
223886715101
823827736009
223878615649
223886715101
202203100205
223878615649
823827736009
223878615649
823827736009
223878615649
823827736009
223878615649
823827736009
223878615649
823827736009
223878615649
202203100205
223878615649
823827736009
223878615649
223878615649
223878615649
823827736009
823827736009
223878615649
823827736009
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
823827736009
823827736009
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
CER2 0603 X7R 16V 47N PM10
CER2 0603 X7R 16V 47N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 47N PM10
CER2 0603 X7R 16V 100N PM10
ELCAP SM HV 16V 22U PM20
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
ELCAP SM HV 16V 22U PM20
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 50V 10N PM10
CHIP 4.7UF 25V X7R 1206
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER1 0603 NP0 50V 22P PM5
CER1 0603 NP0 50V 22P PM5
CER2 0603 X7R 16V 100N PM10
CER1 0603 NP0 50V 100P PM5
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CER1 0603 NP0 50V 100P PM5
ELCAP SM RVS 25V 47U PM20
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
ELCAP SM RVS 25V 47U PM20
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
200WP7 LCD
85
2443
2444
2445
2446
2447
2448
2451
2452
2453
2454
2455
2456
2457
2458
2459
2501
2502
2503
2504
2505
2506
2510
2511
2515
2516
2517
2518
2519
2520
2521
2522
2523
2524
2525
2526
2529
2530
2531
2538
2539
223878615649
223878615649
223878615649
223878615649
223886715339
223886715339
223878615649
223878615649
223878615649
223858615636
823827736009
823827736009
223878615649
823827736009
223878615649
223878615649
223878615649
202203100205
223878615649
223878615649
202203100205
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615645
202203100205
223878615649
223878615649
823827736009
823827736009
223878615649
823827736009
223878615649
823827736009
223878615645
223878615645
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER1 0603 NP0 50V 33P PM5
CER1 0603 NP0 50V 33P PM5
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 50V 10N PM10
CHIP 4.7UF 25V X7R 1206
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
ELCAP SM RVS 25V 47U PM20
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
ELCAP SM RVS 25V 47U PM20
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 47N PM10
ELCAP SM RVS 25V 47U PM20
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 100N PM10
CHIP 4.7UF 25V X7R 1206
CER2 0603 X7R 16V 47N PM10
CER2 0603 X7R 16V 47N PM10
3202
3203
3204
3207
3208
3209
3210
3211
3212
3213
3214
3215
3216
3217
3229
3230
3231
3233
3234
3235
3236
3237
3238
3239
3240
3241
3242
3243
3244
3247
3248
3249
3251
3252
3253
3254
3255
3256
3259
3260
3301
3302
3303
3304
212211805656
212211805656
232270260103
232270260103
232270260103
232270260103
232270260223
232270260101
232270260101
232270260101
232270260101
212211805637
212211805637
212211805637
212211805665
212211805665
212211805641
232270260103
232270260223
232270260101
232270260101
232270260101
232270260101
232270260101
232270260101
212211805661
212211805661
212211805964
212211805638
232270260471
212211805964
212211805638
212211805641
212211805638
212211805964
212211805641
212211805656
232270260103
232270260223
232270260223
212211805656
212211805656
232270260151
212211805637
RST SM 0603 RC0603 1K PM5
RST SM 0603 RC0603 1K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 22K PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 4K7 PM5
RST SM 0603 RC0603 4K7 PM5
RST SM 0603 RC0603 68R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 22K PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC0603 2K2 PM5
RST SM 0603 RC0603 2K2 PM5
RST SM 0603 RC0603 75R PM1
RST SM 0603 RC0603 33R PM5
RST SM 0603 RC21 470R PM5
RST SM 0603 RC0603 75R PM1
RST SM 0603 RC0603 33R PM5
RST SM 0603 RC0603 68R PM5
RST SM 0603 RC0603 33R PM5
RST SM 0603 RC0603 75R PM1
RST SM 0603 RC0603 68R PM5
RST SM 0603 RC0603 1K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 22K PM5
RST SM 0603 RC21 22K PM5
RST SM 0603 RC0603 1K PM5
RST SM 0603 RC0603 1K PM5
RST SM 0603 RC21 150R PM5
RST SM 0603 RC0603 22R PM5
86
Spare Parts List
200WP7 LCD
Go to cover page
3305
3306
3307
3308
3309
3310
3311
3312
3313
3314
3315
3316
3317
3318
3319
3320
3321
3322
3323
3351
3352
3353
3354
3358
3359
3360
3361
3364
3365
3366
3367
3368
3369
3370
3371
3372
3373
3374
3379
3380
3382
3391
3392
3401
3402
3403
3405
3408
3409
3410
3411
3412
3413
3414
3416
3501
3502
3503
3504
3506
3507
3508
3509
3510
3511
3512
3515
3516
3517
3518
3519
3520
3521
3522
3523
3524
3525
3526
3527
3532
3533
3539
212211805637
232270260101
232270260101
232270260101
232270260101
232270260101
232270260101
232270260101
232270260101
235003510101
235003510101
235003510101
235003510101
235003510101
235003510101
235003510101
235003510101
212211805637
212211805637
212211805689
232270260101
232270260103
232270260101
232270260103
232270260101
232270260103
232270260103
232270260103
232270260103
232270260103
232270260103
232270260101
232270260101
232270260103
232270260103
232270260103
232270260101
232270260101
232270260101
232270260101
232270260103
232270296001
232270296001
232270463901
232270260101
212211805637
232270260103
212211805637
212211805637
212211805637
212211805637
212211805637
212211805656
232270260122
232270260101
232270260479
232270260479
232270260479
232270260103
232270260101
232270260101
232270260101
232270260221
232270260103
232270260221
232270260103
232270260103
232270260103
212211805683
232270260103
232270260103
232270260103
212211805683
232270260103
232270260103
212211805683
232270260103
232270260103
232270260223
232270260103
232270296001
232270260103
5201 242254945582
5202 242254945582
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST NETW SM ARV24 4X100R PM5
RST NETW SM ARV24 4X100R PM5
RST NETW SM ARV24 4X100R PM5
RST NETW SM ARV24 4X100R PM5
RST NETW SM ARV24 4X100R PM5
RST NETW SM ARV24 4X100R PM5
RST NETW SM ARV24 4X100R PM5
RST NETW SM ARV24 4X100R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 1M PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 JUMP. MAX 0R05
RST SM 0603 JUMP. MAX 0R05
RST SM 0603 RC22H 390R PM1
RST SM 0603 RC21 100R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 22R PM5
RST SM 0603 RC0603 1K PM5
RST SM 0603 RC21 1K2 PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 47R PM5
RST SM 0603 RC21 47R PM5
RST SM 0603 RC21 47R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 220R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 220R PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC0603 100K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC0603 100K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC0603 100K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC21 22K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 JUMP. MAX 0R05
RST SM 0603 RC21 10K PM5
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
5204
5301
5302
5351
5401
5402
5403
5404
5405
5406
5407
5409
5410
5412
5413
5414
5416
5501
5502
242254945582
242254945582
242254945582
242254945582
242254945582
242254945582
242254945582
242254945582
242254945582
242254945582
242254945582
242254945582
242254945582
242254945582
242254945579
242254945579
242254945579
242254945579
242254945579
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 0805 EMI 100MHZ 300R
IND FXD 1206 EMI 100MHZ 100R
IND FXD 1206 EMI 100MHZ 100R
IND FXD 1206 EMI 100MHZ 100R
IND FXD 1206 EMI 100MHZ 100R
IND FXD 1206 EMI 100MHZ 100R
6201
6202
6203
6204
6401
6402
6403
933913910115
933913910115
933913910115
933913910115
932220675682
932220675682
932220628682
DIO SIG SM BAS32L (PHSE)
DIO SIG SM BAS32L (PHSE)
DIO SIG SM BAS32L (PHSE)
DIO SIG SM BAS32L (PHSE)
DIO REC M100AL-5301-E3 (VISH)
DIO REC M100AL-5301-E3 (VISH)
DIO REC SB140AL-5301E3 (VISH)
7201
7202
7301
7302
7351
7351
7353
7353
7401
7403
7404
7405
7501
7502
7503
7504
7505
7507
7509
7510
7511
7512
932216972682
932216972682
932222292671
932216732668
313815867041
932222343682
313815867051
932214725682
823827716351
932220099685
932216732668
932216733668
933769900215
933769900215
932217440685
932216638668
932216733668
932216733668
932216638668
932216638668
932217440685
932217440685
IC SM AT24C02N-10SC-2.7(ATME)
IC SM AT24C02N-10SC-2.7(ATME)
IC SM K4D263238G-VC36 (SMGK)
IC SM LD1117S25
(ST00)
CPU IC ASSY-LPL(7351)
IC SM NT68F631ALG (NOVA)
EEPROM IC ASSY-LPL(7353)
IC M24C16-WBN6P
(ST00)
SCALER IC
IC SM LD1117AS18
(ST00)
IC SM LD1117S25
(ST00)
IC SM LD1117S33
(ST00)
TRA SIG SM BC857C (PHSE)
TRA SIG SM BC857C (PHSE)
TRA SIG SM KRC102S (KEC0)
FET POW SM SI5441DC-E3 (VISH)
IC SM LD1117S33
(ST00)
IC SM LD1117S33
(ST00)
FET POW SM SI5441DC-E3 (VISH)
FET POW SM SI5441DC-E3 (VISH)
TRA SIG SM KRC102S (KEC0)
TRA SIG SM KRC102S (KEC0)
PCB Assy
1052 313815865861
various
1951 243812800196
1952 243812800196
1953 243812800196
1954 243812800196
1955 243812800196
1956 243812800196
1957 243812800196
1960 243812800196
1961 242202518897
CONTROL ASSY
SWI TACT H=5 GY
SWI TACT H=5 GY
SWI TACT H=5 GY
SWI TACT H=5 GY
SWI TACT H=5 GY
SWI TACT H=5 GY
SWI TACT H=5 GY
SWI TACT H=5 GY
CON H 7P M 2.00
160G SKHHAM
160G SKHHAM
160G SKHHAM
160G SKHHAM
160G SKHHAM
160G SKHHAM
160G SKHHAM
160G SKHHAM
63367
2951 223858619812
2952 223858619812
CER2 0603 Y5V 50V 100N P8020
CER2 0603 Y5V 50V 100N P8020
3951
3952
3953
3954
3955
3956
3957
RST SM 0603 RC21 100R PM5
RST SM 0603 RC21 47K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC0603 1K PM5
RST SM 0603 RC21 47K PM5
RST SM 0603 RC21 10K PM5
RST SM 0603 RC0603 1K PM5
232270260101
232270260473
232270260103
212211805656
232270260473
232270260103
212211805656
6951 932214603682
PCB Assy
1054 313815867111
various
1601 242202518896
1608 823827732071
1609 823827732069
1610 243854300085
1651 242202518953
LED VS L-3WYGW
(KIEL)
USB ASSY(200 WP7)
CON H 6P M 2.00
63366
CABLE RING TERM/45/FAST AWG18
CABLE RING TERM/85/FAST AWG18
RES XTL SM 24MHZ 20P SMD-49
SOC USB V 4P F 2.0/2.5 5401
1652 242202518955
1653 242202518957
1654 242202518953
SOC USB V 4P F 2.5
5411
SOC USB V 8P F 2.0/2.5 5402
SOC USB V 4P F 2.0/2.5 5401
2601
2603
2604
2621
2623
2625
2631
2633
2634
2635
2636
2651
2652
2655
2656
2661
2662
2665
2666
2671
2675
2680
2681
2682
2683
2684
2685
2691
2692
2693
2694
2695
2696
2697
2698
2699
223878615649
202203100179
223858619812
223878615649
223858615636
222224119876
202202000963
223878615649
202202000963
223878615643
222278015663
202001293803
223878615649
202001293803
223878615649
202001293803
223878615649
202001293803
223878615649
223878615649
223878615649
223878615649
223878615649
223886715279
223886715279
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
223878615649
CER2 0603 X7R 16V 100N PM10
ELCAP SM HV 25V 10U PM20
CER2 0603 Y5V 50V 100N P8020
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 50V 10N PM10
CER2 1206 Y5V 10V 10U P8020
ELCAP SM LV 25V 100U PM20
CER2 0603 X7R 16V 100N PM10
ELCAP SM LV 25V 100U PM20
CER2 0603 X7R 16V 33N PM10
CER2 0805 X7R 16V 1U PM10
ELCAP SM RV2 16V 100U PM20
CER2 0603 X7R 16V 100N PM10
ELCAP SM RV2 16V 100U PM20
CER2 0603 X7R 16V 100N PM10
ELCAP SM RV2 16V 100U PM20
CER2 0603 X7R 16V 100N PM10
ELCAP SM RV2 16V 100U PM20
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER1 0603 NP0 50V 27P PM5
CER1 0603 NP0 50V 27P PM5
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
CER2 0603 X7R 16V 100N PM10
3622
3623
3634
3681
3682
3683
3685
3687
3689
3691
3692
3693
4631
232270260103
212211805683
232270260202
212211805672
212211805683
212211805672
212211805672
212211805672
212211805672
212211805672
212211805672
212211805672
232270296001
RST SM 0603 RC21 10K PM5
RST SM 0603 RC0603 100K PM5
RST SM 0603 RC21 2K PM5
RST SM 0603 RC0603 15K PM5
RST SM 0603 RC0603 100K PM5
RST SM 0603 RC0603 15K PM5
RST SM 0603 RC0603 15K PM5
RST SM 0603 RC0603 15K PM5
RST SM 0603 RC0603 15K PM5
RST SM 0603 RC0603 15K PM5
RST SM 0603 RC0603 15K PM5
RST SM 0603 RC0603 15K PM5
RST SM 0603 JUMP. MAX 0R05
5601
5602
5603
5621
5622
5634
5651
5653
5655
5657
5659
242254900126
242254900126
242254900126
242254900126
242254900126
313818875771
242254900126
242254900126
242254900126
242254900126
242254900126
IND FXD 0805 EMI 100MHZ 120R
IND FXD 0805 EMI 100MHZ 120R
IND FXD 0805 EMI 100MHZ 120R
IND FXD 0805 EMI 100MHZ 120R
IND FXD 0805 EMI 100MHZ 120R
COI CHOKE 35UH 82M OHM DR10X8
IND FXD 0805 EMI 100MHZ 120R
IND FXD 0805 EMI 100MHZ 120R
IND FXD 0805 EMI 100MHZ 120R
IND FXD 0805 EMI 100MHZ 120R
IND FXD 0805 EMI 100MHZ 120R
6634 932221745685
6635 932221745685
6662 933913910115
DIO REC SM SSA34-E3 (VISH)
DIO REC SM SSA34-E3 (VISH)
DIO SIG SM BAS32L (PHSE)
7622
7625
7631
7651
7671
7675
TRA SIG SM KRC102S (KEC0)
FET POW SM SI5441DC-E3 (VISH)
IC SM TPS54357PWP (TI00)
IC SM CY7C65640-LFXC (CYPR)
IC SM TPS2062DG4
(TI00)
IC SM TPS2062DG4
(TI00)
932217440685
932216638668
932222352668
932222162671
932222269668
932222269668
200WP7 LCD
Diversity of 200WP7EB/00 compared with 200P7ES/00
Item
12NC
Description
863900017042 200WP7EB/00
0602 313811709571 E-D.F.U.
0130 313815569641 ENERGY STAR LABEL
0004 313815761131 SUPER ERGO BASE ASSY
0140 313800990651 PROCESS BOX
0300 282206240595 INK CARTRIDGE -EP-T
0030 313815761231 BEZEL ASSY
0031 313815418101 BEZEL
0032 313815417971 BEZEL-DECO
0033 313815417981 CONTROL KNOB
0040 313815761121 BACK COVER ASSY
0042 313815418001 MIDDLE COVER
0116 313810440571 HOUSING COVER
87
88
Scaler Diagram-1
200WP7 LCD
1
A
2
CONTENTS
3
4
5
A
REVISION HISTORY
SCHEMATIC Name
SHEET
Date
Author
Ver
Comments
01. Contents
1
2005-09-14
Jerry Chen
A
PHILIPS UH7 200P7 SCALER SEHEMATIC FOR PROTOTYPE
02. DSUB/DVI
2
2005-11-23
Jerry Chen
B
PHILIPS UH7 200WP7 SCALER SEHEMATIC FOR 2nd MODEL
03. MCU
3
2006-02-09
Jerry Chen
C
5205 /5206 /5207 change to 3215 /3216/3217 22R
04. SCALER
4
B
B
05. DDR
5
06. IO
6
C
Position
Approval
Signature
C
Date
CP NR. CL6xxxx
D
D
Title
200WP7ES/01 SCALER BOARD(Contents)
Size
A
Date:
1
2
3
Document Number
Rev
1
3138 158 65851(6319.1) (715G1789-1)
December 01, 2006
4
Sheet
of
1
5
6
Scaler Diagram-2
1
2
3
4
5
200WP7 LCD
6
7
8
9
10
11
+5V_ESD
5201
1
1201
A
31
120 OHM
6202
BAS 32L
2
2201
BAS 32L
0.1uF/16V
31
B
32
6201
RX2RX2+
RX2RX2+
GND
RX4RX4+
SCL
SDA
VS
1
2
3
4
5
6
7
8
RX1RX1+
GND
RX3RX3+
5V
GND
HP
9
10
11
12
13
14
15
16
RX1RX1+
RX0RX0+
GND
RX5RX5+
GND
RXC+
RXC-
17
18
19
20
21
22
23
24
RX0RX0+
RED
GRN
BLU
HS
GND
25
26
27
28
29
RX2RX2+
3207
3208
10K W
10KW
RX2+ 3
3
3211
100 W
3212
4
4
100 W
3203
1K?
RX0RX0+
VCC
WC
SCL
SDA
2203
330pF
DVI_SCL
RX1+ 3
RX1- 3
2231
0.1uF/16V(NC)
BAV99(NC)
1
BAV99(NC)
1
+5V_ESD
6214
3204
10K W
6215
2
3
RX0+ 3
1KW
6216
2
RX0- 3
2232
0.1uF/16V(NC)
BAV99(NC)
1
DVI_CABLE 3
3260
22K W
RXC+
RXC+
RXCRXC-
BAV99(NC)
1
2
M24C02WMN6
3202
4
4
RX2- 3
2230
0.1uF/16V(NC)
1201
1202
2201
2202
2203
2204
2205
2214
2215
2216
2217
2218
2219
2220
2221
2222
2223
2224
2225
2226
2227
2228
2229
2230
2231
2232
2233
2234
2235
2236
2237
2238
2239
2240
2241
2242
2243
3202
3203
3204
3205
3207
3208
3209
3210
3211
3212
3213
3214
3215
3216
3217
3229
3230
3231
3233
3234
3235
3236
3237
3238
3239
3240
3241
3242
3243
3244
3247
3248
3249
3251
3252
3253
3254
3255
3256
3259
3260
5201
5202
5204
6201
6202
6203
6204
6210
6211
6212
6213
6214
6215
6216
6217
6219
6220
6221
6222
6223
6224
6225
6226
6227
7201
7202
6213
2
+5V
3
DVI_SDA
100 W
3210
22KW
6212
2
1
2
3
4
NC/NC/NC/E0/E0
NC/NC/E1/E1/E1
NC/E2/E2/E2/E2
VSS
2204
3213
3214
8
7
6
5
DDC_WP
330pF
6211
BAV99(NC)
1
7201
100 W
RX1RX1+
6210
2202
0.1uF/16V
4
4
DDCSCL_D
DDCSDA_D
+5V
2
3209
10KW
6217
2
BAV99(NC)
1
RXC+ 3
2
RXC- 3
2233
0.1uF/16V(NC)
BAV99(NC)
1
BAV99(NC)
1
2205
0.1uF/16V
4
4
+5V_ESD
6219
6220
2
32
G
C
3
BAV99(NC)
1
DVI_CON
6221
2
R
2234
0.1uF/16V(NC)
2
B
3
BAV99(NC)
1
0.1uF/16V(NC)
2235
3
BAV99(NC)
1
2236
0.1uF/16V(NC)
+5V_ESD
3205
+5V
10K W (NC)
6222
6223
2
D
VIN
6203
HIN
3
2237
0.1uF/16V(NC)
BAV99(NC)
1
6204
+5V
3
6225
2
BAV99(NC)
1
DDCSCL 3
2
DDCSDA
2238
0.1uF/16V(NC)
BAV99(NC)
1
3
BAV99(NC)
1
1
BAS 32L
6224
2
3229
BAS 32L
4.7K W
3230
4.7K W
3233
10K W
2214
0.1uF/16V
5202
2219
0.1uF/16V
7202
3
VCC
WC
SCL
SDA
NC/NC/NC/E0/E0
NC/NC/E1/E1/E1
NC/E2/E2/E2/E2
VSS
2215
E
2216
330pF
330pF
1
2
3
4
2
8
7
6
5
DDC_WP
+5V_ESD
120 OHM
6226
DDCSCL_D
M24C02WMN6
3234
22K W
6227
2
3
2
DDCSDA_D 3
2239
0.1uF/16V(NC)
BAV99(NC)
1
BAV99(NC)
1
3215
3244
33 W
2221
0.047uF
2220
5pF(NC)
3231
68 W
2241
0.047uF
R
3
3236
100 W
100 W
100 W
3237
F
3235
2240
5pF(NC)
22 W 1/16W
DDCSDA
VGA_SDA
3247
RIN+
4
RIN-
4
SOG
4
GIN+
4
GIN-
4
BIN+
4
BIN-
4
0.001uF
470 W
2222
3216
17
11
5204
3238
4
HS_RGB
4
VS_RGB
3
VGA_SCL
12
100 W
1
3239
120 OHM
100 W
2 HIN
13
VIN
14
DDCSCL
3240
100W
2242 22 W 1/16W
5pF(NC)
DB15
1
6
2
7
3
8
4
9
5
10
3217
2218
220pF
3241
2.2K
3252
B
2243
5pF(NC) 22 W 1/16W
3243
75 W
2217
33pF
2223
5pF(NC)
3251
33 W
2224
68 W
0.047uF
0.047uF
2225
16
G
15
3249
G
1202
3248
3253
75 W
75 W
2226
5pF(NC)
3254
33 W
68 W
2227
0.047uF
0.047uF
2228
3242
2.2K W
A1
F3
A2
A4
B3
B3
B4
D3
E2
E2
G1
G2
D4
F5
E6
F6
F5
F6
F6
G5
G6
G6
H5
A7
A9
B7
B9
C7
C8
C10
D7
D9
E9
F4
F6
F5
G5
B3
B2
B4
D6
A3
A3
A4
B4
A2
A2
B2
B2
E5
F5
G5
D2
D2
F6
D2
E2
F2
F3
F2
G2
G2
G2
G2
G3
G4
E6
F6
G4
F6
F6
G6
G5
G6
H4
H4
H4
B4
A2
D4
G3
A3
A5
D1
D3
A6
A8
A8
A10
B6
B8
B8
B10
C6
C8
C9
D6
D8
D8
D10
E8
E10
A4
E3
A
B
C
D
E
F
G
+5V
3256
10K W
3255
VGA_CABLE
1K W
H
3
22K W
3259
2229
0.1uF/16V
Size
C
Date:
1
2
3
4
5
H
CP NR. CL6xxxx
Title
6
7
8
9
200WP7ES/01 SCALER BOARD(DSUB/DVI)
Document Number
Rev
1
3138 158 65851 ( 6319.1) (715G1789-1)
December 01, 2006
10
Sheet
2
of
11
6
89
90
Scaler Diagram-3
200WP7 LCD
1
2
3
4
5
6
7
VCPU
8
+3.3V
A
1351
1352
1353
2351
2353
2354
2355
2356
2358
2359
2360
2361
2362
2363
3351
3352
3353
3354
3358
3359
3360
3361
3364
3365
3366
3367
3368
3369
3370
3371
3372
3373
3374
3379
3380
3381
3382
3391
3392
5351
7351
7353
5351
1
VCPU
2
120 OHM
VCPU
3351
3370
10K?W
2353
22pF
2354
22pF
12.000MHz
7351
2355
100pF(NC)
21
OSCI
20
OSCO
7353
B
1
2
3
4
NC
NC
NC
VSS
VCC
WC
SCL
SDA
8
7
6
5
4
SMARTBRIGHT
24C16_WP
3373
100 ?W
3374
100 ?W
3353
M24C16-WBN6P
INT
3352
10K W
?
100 ?W
6
6 BRIGHTNESS_IDX
2356
0.1uF/16V
6
6
2
14
15
16
17
3391
3392
BL_CONTROL
PANEL_PWR
DVI_CABLE
6 POWER_SAVING
2
3
4
5
6
7
8
9
K_PWR
0W
0W
3380
100 W
3359
100 W
10
VCPU
100 W
3379
C
6
23
KEY2
2361
100pF
2358
44
3371
10K?W
PE1
PE0
VCC
3372
10K?W
2351
0.1uF/16V
3382
10K W
2
PB1/ADC1
PB4*/SCL0*
PB5*/SDA0*
PB2/ADC2/INTE0
PB3/ADC3/INTE1
PB6*/SCL1*
P34/T0
PB7*/SDA1*
P35/T1
PD6
PD5
PA0/PWM2
PD4
PA1/PWM3
PD3
PA2/PWM4
PA3/PWM5
PD2
PA4*/PWM6*
PD1
PA5*/PWM7*
PD0
PA6*/PWM8*
PA7*/PWM9*
PC0*
PC1*
PC2
PC3/PWM0
RSTB
PC4/PWM1
PC5
PC6
PB0/ADC0
PC7
24
25
26
13
11
P31/TXD
P30/RXD
3361
10K W
19
18
GND
1
2360
0.1uF/16V
2359
4.7uF/25V
1M ?W
22
1351
HWRESET
3354
3366
10K W
3365
10K W
3364
10K W
3358
10K W
3360
10K W
100pF
4
100 W
KEY1
2
2
VGA_SCL
VGA_SDA
27
28
12
29
30
31
34
35
1
43
42
41
40
39
38
37
36
3367
10K W
DVI_SCL
DVI_SDA
6
2
2
AD3
AD2
AD1
AD0
ALE
RDZ
WRZ
24C16_WP
VGA_CABLE
DDC_WP
4
4
4
4
4
4
4
2
2
VCPU
LED_R
LED_G
3368
3369
NT68F631ALG
6
6
1352
1
2
3
4
100 W
100 W
CONN
A3
B5
C1
A4
A2
A3
A3
B2
A5
A4
A1
B3
C2
C1
A3
B3
B2
A4
A6
B3
A6
A5
A5
A5
A5
A5
B5
B5
A2
A2
A1
B1
B1
B3
B3
C2
A3
B3
B3
A5
A4
A1
A
B
C
VCPU
D
D
1353
1
2
SMARTBRIGHT
conn (NC)
2363
0.1uF/16V (NC)
3381
10K?W(NC)
2362
0.1uF/16V (NC)
E
E
CP NR. CL6xxxx
Title
200WP7ES/01 SCALER BOARD(MCU)
Size
B
Date:
1
2
3
4
5
6
Document Number
Rev
1
3138 158 65851 (6319.1) (715G1789-1)
December 01, 2006
7
Sheet
3
of
6
8
Scaler Diagram-4
1
2
4
5
6
7
8
9
10
+3.3AVDD
+5V
+3.3VMST
+3.3AVDD
PANEL_VCC
5401
5414
120 OHM
5417
120 OHM (NC)
5403
1
1
+3.3AVDD_A
2
120 OHM
+3.3AVDD
2
120 OHM
1
+3.3AVDD_D
2
120 OHM
1
1
1
5402
5413
100R
A
4
+
2
3
GND Pad
VI
2455
4.7uF/25V
VO
2401
47U/25V
+3.3VMST
2
2403
4.7uF/25V
2402
0.1uF/16V
2404
0.1uF/16V
2451
0.1uF/16V
2405
4.7uF/25V
2406
0.1uF/16V
2452
0.1uF/16V
+3.3AVDD_P
2456
4.7uF/25V
AP1117E33
2457
0.1uF/16V
2
7405
2
11
+3.3AVDD_M
1
+3.3AVDD_P2
1402
31
+5V_PWR
3
200WP7 LCD
18
19
20
21
22
23
24
25
26
HSYNC1
VSYNC1
BIN1
BIN1M
SOGIN1
GIN1
GIN1M
RIN1
RIN1M
27
28
29
30
31
32
33
36
37
38
2443 0.1uF/16V 39
40
2444 0.1uF/16V
BIN0M
BIN0
GIN0M
GIN0
SOGIN0
RIN0M
RIN0
HSYNC0
VSYNC0
RMID
REFP
REFM
3401
390?W1/16W
1
+5V
1
+5V_PWR
5415
120 OHM (NC)
2
2
2
2
2
2
2
2
2
2
2
5416
120 OHM
6401
M100-AL
6402
M100-AL
BINBIN+
GINGIN+
SOG
RINRIN+
HS_RGB
VS_RGB
D
6403
SB140
3
VI
2420
4.7uF/25V
GND Pad
4
7403
VO
+1.8VDD
2
2421
4.7uF/25V
2422
0.1uF/16V
1
LD1117AS18
E
3
3402
HWRESET
3405
10K?W 1/16W
100 W? 1/16W
2445
0.1uF/16V
3
3
3
3
3
3
3
3
INT
ALE
RDZ
WRZ
AD0
AD1
AD2
AD3
3416
6 BRIGHTNESS_RES
41
42
43
44
45
46
47
48
51
52
53
54
55
56
57
58
59
60
61
77
VI_DATA[8]
VI_DATA[9]
VI_DATA[10]
VI_DATA[11]
VI_DATA[12]
VI_DATA[13]
VI_DATA[14]
VI_DATA[15]
GPIO[5]/VHS
GPIO[4]/VCLK2
VI_CK
VI_DATA[0]
VI_DATA[1]
VI_DATA[2]
VI_DATA[3]
VI_DATA[4]
VI_DATA[5]
VI_DATA[6]
VI_DATA[7]
GPIO[2]/VVS
67
68
69
70
71
72
73
74
75
HWRESET
INT
ALE
RDZ
WRZ
DBUS[0]
DBUS[1]
DBUS[2]
DBUS[3]
200
201
PWM0
PWM1
62
158
VCTRL
BYPASS
100? 1/16W
F
2446
0.1uF/16V
202
2
2448
76
78
1401
14.31818MHz
203
199
198
197
196
193
192
191
190
189
188
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
109
12
63
79
131
156
173
185
195
VDDC
VDDC
VDDC
VDDC
VDDC
VDDC
VDDC
VDDM
VDDM
VDDM
VDDM
VDDM
VDDM
49
86
102
113
125
139
154
66
162
182
204
4
10
TXE1TXE0+
TXO3+
TXOC+
2458
4.7uF/25V
3417
LVB0M
LVB0P
LVB1M
LVB1P
LVB2M
LVB2P
LVBCKM
LVBCKP
LVB3M
LVB3P
LVA0M
LVA0P
LVA1M
LVA1P
LVA2M
LVA2P
LVACKM
LVACKP
LVA3M
LVA3P
187
186
181
180
179
178
177
176
175
174
171
170
169
168
167
166
165
164
161
160
DQS[0]
MDATA[0]
MDATA[1]
MDATA[2]
MDATA[3]
MDATA[4]
MDATA[5]
MDATA[6]
MDATA[7]
MDATA[8]
MDATA[9]
MDATA[10]
MDATA[11]
MDATA[12]
MDATA[13]
MDATA[14]
MDATA[15]
DQS[1]
DQM[0]
DQM[1]
DQS[2]
MDATA[16]
MDATA[17]
MDATA[18]
MDATA[19]
MDATA[20]
MDATA[21]
MDATA[22]
MDATA[23]
MDATA[24]
MDATA[25]
MDATA[26]
MDATA[27]
MDATA[28]
MDATA[29]
MDATA[30]
MDATA[31]
DQS[3]
MADR[11]
MADR[10]
MADR[9]
MADR[8]
MADR[7]
MADR[6]
MADR[5]
MADR[4]
MADR[3]
MADR[2]
MADR[1]
MADR[0]
153
152
151
150
149
148
147
146
145
144
143
142
141
138
137
136
135
134
133
101
100
99
98
97
96
95
94
93
92
91
90
89
88
85
84
83
82
81
130
129
128
127
124
123
122
121
120
119
118
117
WEZ
CASZ
RASZ
BADR[0]
BADR[1]
MCLK
MCLKZ
MCLKE
MVREF
TXO0TXO0+
TXO1TXO1+
TXO2TXO2+
TXOCTXOC+
TXO3TXO3+
TXE0TXE0+
TXE1TXE1+
TXE2TXE2+
TXECTXEC+
TXE3TXE3+
0?W(NC))
TXO2TXO1TXO0-
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
CONN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
TXE3TXECTXE2TXE1+
3418
0?W(NC))
TXE0TXO3TXOCTXO2+
TXO1+
TXO0+
3412
MST9251A-LF-165
GPIO[3]/VDE
GPIO[1]/FIELD
XOUT
XIN
22?W
DQS0
MDATA0
MDATA1
MDATA2
MDATA3
MDATA4
MDATA5
MDATA6
MDATA7
MDATA8
MDATA9
MDATA10
MDATA11
MDATA12
MDATA13
MDATA14
MDATA15
DQS1
DQM0
DQM1
DQS2
MDATA16
MDATA17
MDATA18
MDATA19
MDATA20
MDATA21
MDATA22
MDATA23
MDATA24
MDATA25
MDATA26
MDATA27
MDATA28
MDATA29
MDATA30
MDATA31
DQS3
AR11
AR10
AR9
AR8
AR7
AR6
AR5
AR4
AR3
AR2
AR1
AR0
5
5
5
5
5
+3.3AVDD
5
5
5404
5
5
5
1
2
120 OHM
5
5
5
2407
5
4.7uF/25V
5
5
5
5
5
+3.3AVDD
5
5
5405
5
5
5
1
2
120 OHM
5
5
5
2409
5
4.7uF/25V
5
5
5
5
+3.3AVDD
5
5
5406
5
5
5
1
2
120 OHM
5
5
5
2411
5
5
4.7uF/25V
5
5
5
5
5
5
+2.5MVDD
5
5
116
115
112
111
110
WE
CAS
RAS
SBA0
SBA1
5
5
5
5
5
107
106
105
104
MCLK+
MCLKCKE
5
5
5
3411
3408
3409
3410
3403
22
22
22
22
?W
?W
?W
W
?
22 ?W
2447
2408
0.1uF/16V
+3.3AVDD_M
2410
0.1uF/16V
+3.3AVDD_P2
2412
0.1uF/16V
3413
3414
2453
0.1uF/16V
1
7
13
16
35
50
64
65
80
87
103
108
114
126
132
140
155
157
159
163
172
183
184
194
205
206
33pF
+3.3AVDD_P
1K?W1/16W
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
1
33pF
AVDD_PLL2
DVI_R+
DVI_RDVI_G+
DVI_GDVI_B+
DVI_BDVI_CK+
DVI_CKREXT
DDCD_DA
DDCD_CK
AVDD_PLL
207
208
2
3
5
6
8
9
11
14
15
RX2+
RX2RX1+
RX1RX0+
RX0RXC+
RXC-
+3.3AVDD_D
17
34
2419
0.1uF/16V
AVDD_APLL
2
2
2
2
2
2
2
2
2417
0.1uF/16V
VDDP
VDDP
VDDP
2416
0.1uF/16V
AVDD_MPLL
2414
0.1uF/16V
AVDD_DVI
AVDD_DVI
B
7401
2413
47U/25V
TXE3+
TXEC+
TXE2+
2459
0.1uF/16V
+3.3DV
2
120 OHM
AVDD_ADC
AVDD_ADC
1
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
+3.3AVDD_A
+
C
+1.8VDDC1
+1.8VDDC2
5407
+3.3VMST
+2.5MVDD
32
+3.3DV
31
+3.3AVDD_D
2454
0.01uF
1401
1402
2401
2402
2403
2404
2405
2406
2407
2408
2409
2410
2411
2412
2413
2414
2415
2416
2417
2419
2420
2421
2422
2423
2424
2425
2426
2427
2428
2429
2430
2431
2432
2433
2434
2435
2436
2437
2438
2439
2440
2441
2442
2443
2444
2445
2446
2447
2448
2451
2452
2453
2454
2455
2456
2457
2458
2459
3401
3402
3403
3405
3408
3409
3410
3411
3412
3413
3414
3416
3417
3418
5401
5402
5403
5404
5405
5406
5407
5409
5410
5412
5413
5414
5415
5416
5417
6401
6402
6403
7401
7403
7404
7405
F3
B10
A4
A4
A5
A6
A8
A8
D10
D10
E10
E10
E10
E10
B2
B2
G2
B2
B3
B3
E1
E2
E2
H2
H2
H2
H3
G2
G3
H3
H4
G3
H4
H5
H6
H6
H7
H7
H7
H8
H8
H8
H9
D3
D3
E2
F3
F3
F3
A6
A8
G10
G10
A1
A2
A2
B9
B9
C3
E2
E8
E2
D8
D8
D8
D8
C8
F10
G9
F3
B9
B11
A3
A5
A7
D10
D10
E10
B1
G1
H1
H6
A9
A1
C1
C1
A1
D1
D1
D1
B4
D1
H5
A1
A
B
C
D
E
F
1.2K?W1/16W
+1.8VDD
5409
G
G
1
+1.8VDDC2
2
120 OHM
2415
4.7uF/25V
2427
0.1uF/16V
2428
0.1uF/16V
2431
0.1uF/16V
7404
5412
3
5410
+1.8VDDC1
2
120 OHM
2432
4.7uF/25V
+2.5MVDD
VO
2
LD1117S25
1
2433
4.7uF/25V
2
120 OHM
2434
0.1uF/16V
2435
0.1uF/16V
2436
0.1uF/16V
2437
0.1uF/16V
2438
0.1uF/16V
2439
0.1uF/16V
2440
0.1uF/16V
2441
0.1uF/16V
2442
0.1uF/16V
1
1
VI
GND Pad
4
+5V_PWR
H
2423
4.7uF/25V
2424
0.1uF/16V
2425
0.1uF/16V
2426
0.1uF/16V
2429
0.1uF/16V
2430
0.1uF/16V
H
CP NR. CL6xxxx
Title
200WP7ES/01 SCALER BOARD(SCALER MST9251A)
Size
C
Date:
1
2
3
4
5
6
7
8
9
Document Number
Rev
1
3138 158 65851(6319.1) (715G1789-1)
December 01, 2006
10
Sheet
4
of
11
6
91
Scaler Diagram-5
200WP7 LCD
1
2
3
4
5
6
7
8
9
10
11
5301
+2.5VDDR
1
+2.5V_DMQ
2
120 OHM
2302
0.1uF/16V
A
+
2303
22U/16V
2304
0.1uF/16V
2305
0.1uF/16V
2306
0.1uF/16V
2307
0.1uF/16V
2308
0.1uF/16V
2309
0.1uF/16V
2310
0.1uF/16V
A
2302
2303
2304
2305
2306
2307
2308
2309
2310
2311
2312
2313
2314
2315
2316
2317
2318
2319
2320
2321
2322
2323
2324
2325
2326
2327
2328
2329
2330
2332
2333
2334
3301
3302
3303
3304
3305
3306
3307
3308
3309
3310
3311
3312
3313
3314
3315
3316
3317
3318
3319
3320
3321
3322
3323
5301
5302
7301
7302
7302
4
+5V_PWR
VI
GND Pad
3
2332
4.7uF/25V
VO
2
+2.5VDDR
2333
4.7uF/25V
LD1117S25
1
2334
0.1uF/16V
2321
0.1uF/16V
2322
0.1uF/16V
2323
0.1uF/16V
2324
0.1uF/16V
2325
0.1uF/16V
2326
0.1uF/16V
2327
0.1uF/16V
2328
0.1uF/16V
5302
1
B
+2.5V_DMC
2
120 OHM
2311
0.1uF/16V
+
2312
22U/16V
2313
0.1uF/16V
2314
0.1uF/16V
2315
0.1uF/16V
2316
0.1uF/16V
2317
0.1uF/16V
2318
0.1uF/16V
2319
0.1uF/16V
2320
0.1uF/16V
C
DATA0
DATA1
DATA2
DATA3
3314
8
7
6
5
100 W
? 1/16W
1
2
3
4
MDATA0
MDATA1
MDATA2
MDATA3
4
4
4
4
DATA4
DATA5
DATA6
DATA7
3315
8
7
6
5
100 W? 1/16W
1
2
3
4
MDATA4
MDATA5
MDATA6
MDATA7
4
4
4
4
DATA8
DATA9
DATA10
DATA11
3318
8
7
6
5
100 W? 1/16W
1
2
3
4
MDATA8
MDATA9
MDATA10
MDATA11
4
4
4
4
DATA12
DATA13
DATA14
DATA15
3319
8
7
6
5
100 W? 1/16W
1
2
3
4
MDATA12
MDATA13
MDATA14
MDATA15
4
4
4
4
DATA16
DATA17
DATA18
DATA19
3316
8
7
6
5
100 W? 1/16W
1
2
3
4
MDATA16
MDATA17
MDATA18
MDATA19
4
4
4
4
DATA20
DATA21
DATA22
DATA23
3317
8
7
6
5
100 W
? 1/16W
1
2
3
4
MDATA20
MDATA21
MDATA22
MDATA23
4
4
4
4
DATA24
DATA25
DATA26
DATA27
3320
8
7
6
5
100 W? 1/16W
1
2
3
4
MDATA24
MDATA25
MDATA26
MDATA27
4
4
4
4
DATA28
DATA29
DATA30
DATA31
3321
8
7
6
5
100 W? 1/16W
1
2
3
4
MDATA28
MDATA29
MDATA30
MDATA31
4
4
4
4
+2.5V_DMQ
3301
1K?
D
+2.5V_DMC
+2.5V_DMQ
3302
F
4
4
DQM0
DQM1
DQM0
DQM1
4
4
4
4
DQS0
DQS2
DQS1
DQS3
22?W
22?W
MCLK+
MCLK4
CKE
4
4
4
RAS
CAS
WE
SBA0
SBA1
N4
M5
0
1
C3
E3
F4
G4
J4
K4
C5
C7
C8
C10
F11
G11
J11
K11
C12
E12
N13
VREF
M3
N3
C4
H4
M4
C11
H11
L12
L13
1
2
L9
M10
MCL
M13
K4D263238G-VC36
B3
H12
H3
B12
0
1
2
3
100?W
100?W
100?W
100?W
3303
3310
3311
3312
3313
150 W
?
B2
H13
H2
B13
0
1
2
3
M11
M12
N12
N2
M2
L2
L3
CK
CK
CKE
CS
RAS
CAS
WE
F6
G6
H6
J6
F7
G7
H7
J7
F8
G8
H8
J8
F9
G9
H9
J9
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
Thermal
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
G
NC
NC
NC
NC
NC
NC
NC
NC
NC
[ 1M x 32 bits x 4 banks
3306
3307
3308
3309
22 ?W1/16W
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
B7
C6
B6
B5
C2
D3
D2
E2
K13
K12
J13
J12
G13
G12
F13
F12
F3
F2
G3
G2
J3
J2
K2
K3
E13
D13
D12
C13
B10
B9
C9
B8
128Mb GDDR SDRAM
100?W
100?W
100?W
100?W
3322
3323
3304
0
1
2
3
4
5
6
7
8
9
10
11
2330
0.01uF
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA16
DATA17
DATA18
DATA19
DATA20
DATA21
DATA22
DATA23
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
DATA24
DATA25
DATA26
DATA27
DATA28
DATA29
DATA30
DATA31
B
C
D
E
F
3305
G
22?W
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
4
4
4
4
4
4
AR0
AR1
AR2
AR3
AR4
AR5
AR6
AR7
AR8
AR9
AR10
AR11
2329
0.1uF/16V
A5
A5
A5
A6
A6
A6
A7
A7
A7
B5
B5
B5
B6
B6
B6
B7
B7
B7
B8
B5
B6
B6
B6
B7
B7
B7
B8
D6
D6
B1
B2
B3
D6
D6
F3
F3
G6
F3
F3
F3
F3
F3
F3
F3
F3
C9
D9
E9
E9
D9
E9
F9
F9
F2
F2
A4
B4
E3
A2
B4
D4
D5
F5
G5
H5
J5
K5
D6
E6
D9
E9
D10
F10
G10
H10
J10
K10
B11
D11
4
4
4
4
4
4
4
4
4
4
4
4
E
N5
N6
M6
N7
N8
M9
N9
N10
N11
M8
L6
M7
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
7301
E4
L4
D7
L7
D8
L8
E11
L11
1K?W
E5
L5
K6
E7
K7
E8
K8
K9
E10
L10
92
H
H
CP NR. CL6xxxx
Title
200WP7ES/01 SCALER BOARD(DDR)
Size
C
Date:
1
2
3
4
5
6
7
8
9
Document Number
3138 158 65851(6319.1)
December 01, 2006
10
Rev
1
(715G1789-1)
Sheet
5
of
11
6
Scaler Diagram-6
1
2
3
4
5
200WP7 LCD
6
7
8
9
10
11
+3.3V
A
1501
1505
2501
2502
2503
2504
2505
2506
2510
2511
2515
2516
2517
2518
2519
2520
2521
2522
2523
2524
2525
2526
2529
2530
2531
2532
2533
2534
2535
2536
2537
2538
2539
3501
3502
3503
3504
3506
3507
3508
3509
3510
3511
3512
3515
3516
3517
3518
3519
3520
3521
3522
3523
3524
3525
3526
3527
3529
3530
3531
3532
3533
3534
3535
3536
3537
3538
3539
5501
5502
5503
6501
7501
7502
7503
7504
7505
7507
7508
7509
7510
7511
7512
+3.3V_USB
3501
47 W? 1/16W
3502
47 W? 1/16W
1505
BL_CONTROL 3
47 W? 1/16W
3503
1
2
3
4
5
6
7
8
9
10
11
2522
BRIGHTNESS_RES 4
3504
10K?W
0.1uF/16V
BRIGHTNESS_IDX 3
1501
3535
0?W(NC)
2511
0.1uF/16V
2510
0.1uF/16V
2537
0.1uF/16V(NC)
1
2
3
4
5
6
7
8
9
10
11
12
13
5501
100R
2
1
CONN
5502
1
+12V
100R
2
+5V
+
2501
0.1uF/16V
3516
10K?W
2523
3519
10K?W
B
3515
10K?W
+12V_PWR
2504
0.1uF/16V
2502
0.1uF/16V
2505
0.1uF/16V
2503
47U/25V
+
+12V
+5V
2506
47U/25V
0.1uF/16V
3506
2515
KEY1
3
KEY2
3
100?W1/16W
0.1uF/16V
3507
CONN
2516
100?W1/16W
0.1uF/16V
3508
K_PWR
2517
C
3
100?W1/16W
0.1uF/16V
2
+3.3V
220?W1/16W
3509
3510
1
7501
LED_R
+5V
D
+5V_AUO
3534
0?W(NC)
+5V
3
0.1uF/16V
3533
0?W
+3.3V
2
3537
0?W(NC)
+12V
220?W1/16W
3511
3512
1
7502
LED_G
3517
7504
4
3
2
1
100K?W1/16W
3520
10K?W
G
D
D
D
3522
10K?W
2519
3521
SI5441DC
S 5
D 6
D 7
D 8
7509
4
3
2
1
100K?W 1/16W
2520
0.047uF
E
2521
47U/25V
3523
10K?W
PANEL_VCC
3
+
G
D
D
D
SI5441DC
S 5
D 6
D 7
D 8
3536
0?W(NC)
3
10K?W
BC857
3518
10K?W
3
10K?W
BC857
2518
0.1uF/16V
+12V
2538
0.047uF
+5V_PWR
3526
10K?W
3
7503
MUN2211J
PANEL_PWR
3525
10K?W
3 POWER_SAVING
7511
MUN2211J
3524
3532
10K?W
7510
4
3
2
1
100K?W1/16W
3527
22K?W1/16W
F
2525
4.7uF/25V
3
2526
0.1uF/16V
VI
2531
4.7uF/25V
4
+12V_PWR
VO
+
+3.3V_USB
2
C
D
E
F
2529
4.7uF/25V
2530
0.1uF/16V
8
VCC
5
FB
L5972D013TR(NC)
2534
0.1uF/(NC)
3530
3.3K?W(NC)
2533
0.1uF(NC)
5503
7508
AP1117E33
2532
470uF/25V(NC)
OUT
1
COMP
4
GND
GND
GND
GND
AP1117E33
B
+5V_AUO
G
Choke Coil 35uH(NC)
6501
SSA34-E3(NC)
2
3
6
7
+3.3V
2
GND Pad
4
VO
1
2524
4.7uF/25V
7507
1
G
VI
GND Pad
3
+12V_PWR
A
10K?W(NC)
+5V_PWR
7505
3538
0?W(NC)
3539
10K?W
3529
+5V
SI5441DC
S 5
D 6
D 7
D 8
2539
0.047uF
7512
MUN2211J
3 POWER_SAVING
G
D
D
D
B6
A1
B2
B3
B4
B2
B4
B4
B3
B3
B8
C8
C8
D8
E8
E2
D3
A7
B7
G1
G2
G2
G4
G5
G3
G8
G9
G6
G7
G8
B3
E5
F9
A4
A4
A4
A9
B9
B9
C9
D8
D9
D8
D9
A9
A10
E2
D1
B2
E1
E5
D4
E4
E8
E3
E8
F8
G7
G6
G8
E6
D3
D3
B2
E6
D2
E10
F9
B3
B3
G7
G7
D9
D9
E1
E2
G1
G3
G6
E5
E9
E4
F8
2535
220pF(NC)
2536
0.022uF
3531
4.7K?W(NC)
H
H
CP NR. CL6xxxx
Title
Size
C
Date:
1
2
3
4
5
6
7
8
9
200WP7ES/01 SCALER BOARD(I/O)
Document Number
3138 158 65851(6319.1)
December 01, 2006
10
Rev
1
(715G1789-1)
Sheet
6
of
11
6
93
94
200WP7 LCD
Scaler Board C.B.A.-1
1201
1202
1351
1352
1353
1401
1402
1501
1505
2201
2202
2203
2204
2205
2214
2215
2216
2217
2218
2219
2220
2221
2222
2223
2224
2225
2226
2227
2228
2229
2230
2231
2232
2233
2234
2235
2236
2237
2238
2239
2240
2241
2242
2243
2302
2303
2304
2305
2306
2307
2308
2309
2310
2311
2312
D2
D3
B3
C4
B4
C1
B1
B4
A4
D2
D2
D2
D2
D2
D2
D2
D2
C2
C2
D2
C2
C2
C2
C2
C2
C2
C2
C2
C2
D2
D1
D1
D1
D1
D3
D3
D3
D3
D2
D2
D3
C2
D3
D3
A3
A3
A2
A2
A2
A3
A2
A2
A2
A3
A3
2313
2314
2315
2316
2317
2318
2319
2320
2321
2322
2323
2324
2325
2326
2327
2328
2329
2330
2332
2333
2334
2351
2353
2354
2355
2356
2358
2359
2360
2361
2362
2363
2401
2402
2403
2404
2405
2406
2407
2408
2409
2410
2411
2412
2413
2414
2415
2416
2417
2419
2420
2421
2422
2423
2424
A2
A2
B2
A3
A2
B2
A2
A2
A2
A2
A2
A2
A2
A2
A2
A2
B2
B2
A3
A3
A3
C3
B3
B3
C3
C3
B3
C3
C3
B3
B4
B4
A1
A1
C1
C2
C1
C2
C1
C2
C1
C1
A1
B2
B1
C2
B3
B1
B1
B1
B3
B3
B3
B3
C1
2425
2426
2427
2428
2429
2430
2431
2432
2433
2434
2435
2436
2437
2438
2439
2440
2441
2442
2443
2444
2445
2446
2447
2448
2451
2452
2453
2454
2455
2456
2457
2458
2459
2501
2502
2503
2504
2505
2506
2510
2511
2515
2516
2517
2518
2519
2520
2521
2522
2523
2524
2525
2526
2529
2530
B1
B1
B2
C2
B1
B2
C2
A1
B1
B2
B2
B1
B2
B2
B2
B2
B2
B2
C2
C2
C2
B1
C1
C1
C2
C1
B2
B2
A1
B1
A1
B1
B1
A4
A4
A4
B4
B4
B4
A4
A4
C4
C4
C4
C4
C4
A3
A3
B4
B4
C4
C4
C4
B4
B4
2531
2532
2533
2534
2535
2536
2537
2538
2539
3202
3203
3204
3205
3207
3208
3209
3210
3211
3212
3213
3214
3215
3216
3217
3229
3230
3231
3233
3234
3235
3236
3237
3238
3239
3240
3241
3242
3243
3244
3247
3248
3249
3251
3252
3253
3254
3255
3256
3259
3260
3301
3302
3303
3304
3305
B4
A4
A4
A4
A3
A3
A4
A3
B4
D2
D2
D2
D3
D2
D2
D2
D2
C2
C2
C2
C2
D3
D3
D3
D2
D2
C2
D2
D2
C2
C2
C2
D3
D3
C2
D3
D3
D3
C2
C2
D3
C2
C2
C2
D3
C2
D2
D2
D2
D2
B2
B2
B2
B2
B2
3306
3307
3308
3309
3310
3311
3312
3313
3314
3315
3316
3317
3318
3319
3320
3321
3322
3323
3351
3352
3353
3354
3358
3359
3360
3361
3364
3365
3366
3367
3368
3369
3370
3371
3372
3373
3374
3379
3380
3381
3382
3391
3392
3401
3402
3403
3405
3408
3409
3410
3411
3412
3413
3414
3416
B2
B2
B2
B2
A2
B2
B2
A3
A2
A2
B2
B2
A2
A2
B3
A3
B2
B2
B3
C4
C3
B3
C3
C4
C3
C4
C3
C3
C3
B3
C3
C3
B3
B4
C3
C4
B3
B3
C4
B4
C4
C3
C3
C2
C2
B2
C2
B2
B2
B2
B2
B1
B2
B2
C1
3417
3418
3501
3502
3503
3504
3506
3507
3508
3509
3510
3511
3512
3515
3516
3517
3518
3519
3520
3521
3522
3523
3524
3525
3526
3527
3529
3530
3531
3532
3533
3534
3535
3536
3537
3538
3539
5201
5202
5204
5301
5302
5351
5401
5402
5403
5404
5405
5406
5407
5409
5410
5412
5413
5414
B1
B1
A4
A4
A4
C4
C4
C4
C4
C4
C4
C4
C4
C4
C4
A3
A3
A4
A3
A3
A3
A3
B4
A3
B4
B4
A4
A4
A3
A3
B4
A4
A4
A3
B4
B4
B4
D2
D2
D3
A3
A3
C3
A1
C1
C1
C1
C1
A1
B1
B3
B3
B1
B1
A1
5415
5416
5417
5501
5502
5503
6201
6202
6203
6204
6210
6211
6212
6213
6214
6215
6216
6217
6219
6220
6221
6222
6223
6224
6225
6226
6227
6401
6402
6403
6501
7201
7202
7301
7302
7351
7353
7401
7403
7404
7405
7501
7502
7503
7504
7505
7507
7508
7509
7510
7511
7512
A3
A3
A1
B4
B4
A4
D2
D2
D2
D2
D1
D1
D1
D1
D1
D1
D1
D1
D3
D3
D3
D3
D3
D2
D2
D2
D2
B3
B3
B3
A3
C2
C2
A2
A3
C3
B4
B2
B3
B1
B1
C4
C4
A3
A3
C4
B4
A3
A3
B4
A3
B4
Scaler Board C.B.A.-2
200WP7 LCD
95
96
Updated Parts
200WP7 LCD
Go to cover page
According to the ECO-CA005956,Add QSG-ergo base and Jig on P.E. bag for 200WP7,Following is the detail
1.Item 0129 Qty from 1to 2, and add new Item: 0142-313815524581- QUICK SET GUIDE-ERGO BASE
2.
REF
12NC
Description
1
863900016908 200WP7ES/00
2
863900017042 200WP7EB/00
3
863900017096 200WP7ES/01
4
863900017104 200WP7EB/01
REF
Action
1, 3
From
2, 4
0004
Item
12NC
Description
313815761011 SUPER ERGO BASE ASSY
To
0004
313815761012 SUPER ERGO BASE ASSY
From
0004
313815761131 SUPER ERGO BASE ASSY
To
0004
313815761132 SUPER ERGO BASE ASSY
According to the ECO-CA006109,designer changed the scaler board version of 200WP7-AUO to improve phase and tail noise problem,
following is the detail
REF
ALL
Action
From
To
From
Item
0001
0001
2425
To
2425
From
3231
To
3231
From
3251
To
3251
From
3254
To
3254
ALL
Del
3261
ALL
Del
3262
ALL
Del
3263
ALL
New
5205
ALL
New
5206
ALL
New
5207
ALL
ALL
ALL
ALL
12NC
313810363221
313810363222
202203100205
202203100206
823827736068
823827736069
212211805642
232270260759
212211805643
232270260101
212211805642
232270260759
212211805643
232270260101
212211805642
232270260759
212211805643
232270260101
212211805631
232270296001
212211805631
232270296001
212211805631
232270296001
242254900601
242254943769
242254900601
242254943769
242254900601
242254943769
Description
SCALER PCB
SCALER PCB
ELCAP SM RVS 25V 47U PM20 R
ELCAP SM HV 25V 47U PM20 R
ELCAP 470UF 16V EB
ELCAP 470UF 16V LZ
RST SM 0603 RC0603 75R PM5 R
RST SM 0603 RC21 75R PM5 R
RST SM 0603 RC0603 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC0603 75R PM5 R
RST SM 0603 RC21 75R PM5 R
RST SM 0603 RC0603 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 RC0603 75R PM5 R
RST SM 0603 RC21 75R PM5 R
RST SM 0603 RC0603 100R PM5 R
RST SM 0603 RC21 100R PM5 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 JUMP. MAX 0R05 R
RST SM 0603 JUMP. MAX 0R05 R
IND FXD 0603 EMI 100MHZ 30R R
IND FXD 0603 EMI 100MHZ 30R R
IND FXD 0603 EMI 100MHZ 30R R
IND FXD 0603 EMI 100MHZ 30R R
IND FXD 0603 EMI 100MHZ 30R R
IND FXD 0603 EMI 100MHZ 30R R
200WP7 LCD
Manual 12NC(VERSION)
3138 106 10503
3138 106 10503
3138 106 10503
3138 106 10503
3138 106 10504
Release Date
Apr-7-06
Apr-20-06
Apr-28-06
Jun-02-06
Dec-04-06
97
Change Instruction
Initial Release
Panel changed(P84)
Add QSG-ergo base and Jig on P.E. bag (P86)
Change scaler board version(P86)
Add 200WP7ES/01(P88~P95)
Download PDF

advertising