HTR-6160_U-cv.fm Page 1 Monday, December 10, 2007 2:07 PM
U
HTR-6160
HTR-6160
AV Receiver
© 2008
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Black process 45.0° 240.0 LPI
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WN25460
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
10
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions
should be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to
overturn.
Caution-i En
11
12
13
14
15
16
17
18
19
Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
IMPORTANT SAFETY INSTRUCTIONS
d)
20
21
22
23
If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f)
When the product exhibits a distinct change in performance - this indicates a need for service.
Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24
Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
Caution-ii En
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
Caution: Read this before operating your unit.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– other components, as they may cause damage and/or
discoloration on the surface of this unit.
– burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
Caution-iii En
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
18 Before moving this unit, press L SYSTEM OFF to set this
unit to the standby mode, and then disconnect the AC power
plug from the AC wall outlet.
19 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like.
20 Excessive sound pressure from earphones and headphones can
cause hearing loss.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
As long as this unit is connected to the AC wall outlet,
it is not disconnected from the AC power source even
if you turn off this unit by L SYSTEM OFF. In this
state, this unit is designed to consume a very small
quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
POUR LES CONSOMMATEURS CANADIENS
Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de
la prise et pousser jusqu’au fond.
Cet appareil numérique de la classe B est conforme à
la norme NMB-003 du Canada.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
Contents
Features ................................................................... 2
Supplied accessories .................................................. 2
Notice ....................................................................... 3
Getting started ........................................................ 4
Quick start guide .................................................... 5
Connections ........................................................... 10
Optimizing the speaker setting for your listening
room (YPAO) .................................................... 32
Using AUTO SETUP .............................................. 32
BASIC OPERATION
Connecting the SiriusConnect™ tuner .................... 62
Activating SIRIUS Satellite Radio™
subscription ......................................................... 63
Basic SIRIUS Satellite Radio™ operations ............ 63
Setting the SIRIUS Satellite Radio™
preset channels .................................................... 65
Setting the Parental Lock......................................... 65
Displaying the SIRIUS Satellite Radio™
information .......................................................... 67
Using iPod™ ..........................................................68
Controlling iPod™................................................... 68
Using Bluetooth™ components............................70
Pairing the Bluetooth™ adapter and your
Bluetooth™ component....................................... 70
Playback of the Bluetooth™ component ................. 70
PREPARATION
PREPARATION
SIRIUS Satellite Radio™ tuning .........................62
INTRODUCTION
INTRODUCTION
Recording ...............................................................71
Selecting the SCENE templates........................... 37
Playback ................................................................ 42
Selecting sound field programs ............................... 48
Sound field program descriptions............................ 48
Enjoying unprocessed input sources
(Straight decoding mode) .................................... 51
Using audio features ............................................. 52
Adjusting the speaker level...................................... 52
Enjoying pure hi-fi sound ........................................ 52
Adjusting the tonal quality....................................... 52
FM/AM tuning ...................................................... 53
XM Satellite Radio tuning ................................... 57
Connecting the XM Mini-Tuner Dock .................... 57
Activating XM Satellite Radio ................................ 58
Basic XM Satellite Radio operations....................... 58
Setting the XM Satellite Radio
preset channels .................................................... 60
Displaying the XM Satellite Radio
information .......................................................... 61
Customizing this unit (MANUAL SETUP).........80
Using SET MENU................................................... 84
1 BASIC MENU...................................................... 85
2 VOLUME MENU ................................................ 89
3 SOUND MENU.................................................... 90
4 INPUT MENU...................................................... 93
5 OPTION MENU................................................... 96
Remote control features......................................100
Controlling this unit, a TV, or other components.......... 100
Setting remote control codes ................................. 102
Using multi-zone configuration..........................103
Connecting Zone 2................................................. 103
Controlling Zone 2................................................. 104
Advanced setup....................................................106
Using the advanced setup ...................................... 106
ADDITIONAL INFORMATION
Troubleshooting...................................................110
Resetting the system............................................119
Glossary................................................................120
Sound field program information......................123
Specifications .......................................................124
Index .....................................................................126
APPENDIX
Overview.................................................................. 53
Basic tuning operations............................................ 53
Using station preset feature ..................................... 54
Changing sound field parameter settings................. 72
Selecting decoders ................................................... 78
ADDITIONAL
INFORMATION
Sound field programs .......................................... 48
Advanced sound configurations...........................72
ADVANCED
OPERATION
Basic procedure ....................................................... 42
Selecting the MULTI CH INPUT component......... 43
Selecting the front speaker set ................................. 43
Selecting audio input jacks (AUDIO SELECT)...... 44
Displaying the current status of this unit on a video
monitor ................................................................ 44
Using your headphones............................................ 45
Muting the audio output........................................... 45
Playing video sources
in the background of an audio source.................. 45
Displaying the input source information ................. 46
Using the sleep timer ............................................... 47
ADVANCED OPERATION
BASIC
OPERATION
Selecting the desired SCENE template to the SCENE
buttons ................................................................. 37
Creating your original SCENE templates................ 40
Using the remote control for the SCENE feature .... 41
APPENDIX
(at the end of this manual)
Front panel................................................................i
Remote control ....................................................... ii
List of remote control codes ................................. iii
1 En
English
“ASPEAKERS” or “4DVD” (example) indicates the name
of the parts on the front panel or the remote control. Refer to
the attached sheet or the pages at the end of this manual for
the information about each position of the parts.
FEATURES
Features
Built-in 7-channel power amplifier
HDMI™ (High-Definition Multimedia Interface)
◆ Minimum RMS output power
(1 kHz, 0.7% THD, 8 Ω)
Front: 110 W + 110 W
Center: 110 W
Surround: 110 W + 110 W
Surround back: 110 W + 110 W
◆ HDMI interface for standard, enhanced or
high-definition video as well as multi-channel digital audio
based on HDMI version 1.3a (HDMI is Licensed by HDMI
Licensing, LLC.)
– Automatic audio and video synchronization (lip sync)
information capability
– Deep Color video signal (30/36 bit) transmission capability
– “x.v.Color” video signal transmission capability
– High refresh rate and high resolution video signals
capability
– High definition digital audio format signals capability
◆ HDCP (High-bandwidth Digital Content Protection System)
licensed by Digital Content Protection, LLC.
◆ Analog video to HDMI digital video up-conversion
(composite video ↔ S-video ↔ component video → HDMI
digital video) capability for monitor out
SCENE function
◆ Preset SCENE templates for various situations
◆ SCENE templates for customizing capability
◆ Controlling Yamaha SCENE control signal support
component (some models only) working with the SCENE
function
Sound field programs
◆ Proprietary Yamaha technology for the creation of sound
fields
◆ Compressed Music Enhancer mode
◆ Virtual CINEMA DSP
◆ SILENT CINEMA
Digital audio decoders
◆ Dolby TrueHD, Dolby Digital Plus decoder
◆ DTS-HD Master Audio, DTS-HD High Resolution Audio
decoder
◆ Dolby Digital/Dolby Digital EX decoder
◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS 96/24 decoder
◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx
decoder
◆ Neural Surround decoder
Radio tuners
◆ FM/AM tuning capability
◆ XM Satellite Radio tuning capability (using XM Mini-Tuner
and Home Dock, sold separately)
◆ SIRIUS Satellite Radio™ tuning capability (using
SiriusConnect tuner, sold separately)
DOCK terminal
◆ DOCK terminal to connect a Yamaha iPod universal dock
(such as YDS-10, sold separately) or Bluetooth adapter (such
as YBA-10, sold separately).
Other features
◆ YPAO (Yamaha Parametric Room Acoustic Optimizer) for
automatic speaker setup
◆ 192-kHz/24-bit D/A converter
◆ OSD (on-screen display) menus that allow you to optimize
this unit to suit your individual audiovisual system
◆ 5.1 or 7.1-channel additional input jacks for discrete multichannel input
◆ Component video input/output capability includes
(3 COMPONENT VIDEO INs and 1 MONITOR OUT)
◆ Digital video signal conversion (composite video ↔ S-video
↔ component video) capability for monitor out
◆ Pure Direct mode for pure hi-fi sound for all sources
◆ Adaptive dynamic range controlling capability
◆ Adaptive DSP effect level controlling capability
◆ iPod controlling capability
◆ Remote control with preset remote control codes capability
◆ Zone 2 custom installation facility
◆ Bi-amplification connection capability
◆ Sleep timer
Supplied accessories
Check that you received all of the following parts.
❏ Remote control
❏ Batteries (2) (AAA, R03, UM-4)
❏ Optimizer microphone
2 En
❏ AM loop antenna
❏ Indoor FM antenna
Notice
Notice
• y indicates a tip for your operation.
• Some operations can be performed by using either the
buttons on the front panel or the ones on the remote
control. In case the button names differ between the front
panel and the remote control, the button name on the
remote control is given in parentheses.
• This manual is printed prior to production. Design and
specifications are subject to change in part as a result of
improvements, etc. In case of differences between the
manual and product, the product has priority.
• “ASPEAKERS” or “4DVD” (example) indicates the
name of the parts on the front panel or the remote control.
Refer to the attached sheet or the pages at the end of this
manual for the information about each position of the
parts.
• The symbol “☞ ” with page number(s) indicates the
corresponding reference page(s).
iPod™
“iPod” is a trademark of Apple Inc., registered in the U.S. and
other countries.
Bluetooth™
Bluetooth is a registered trademark of the Bluetooth SIG and is
used by Yamaha in accordance with a license agreement.
INTRODUCTION
About this manual
“HDMI”, the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks or registered trademarks of HDMI
Licensing LLC.
x.v.Color™
“x.v.Color” is a trademark of Sony Corporation.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s
Consumer Electronics Group want you to get the
most out of your equipment by playing it at a safe
level. One that lets the sound come through loud and
clear without annoying blaring or distortion – and,
most importantly, without affecting your sensitive
hearing. Since hearing damage from loud sounds is often
undetectable until it is too late, Yamaha and the Electronic
Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive
volume levels.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
“SILENT CINEMA” is a trademark of Yamaha Corporation.
The XM name and related logos are registered trademarks of XM
Satellite Radio Inc.
Neural Surround™ name and related logos are trademarks owned
by Neural Audio Corporation.
©2006 SIRIUS Satellite Radio Inc. “SIRIUS”, “SiriusConnect”,
the SIRIUS dog logo, channel names and logos are trademarks of
SIRIUS Satellite Radio Inc.
Manufactured under license under U.S. Patent No’s:
5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535
& other U.S. and worldwide patents issued & pending. DTS is a
registered trademark and the DTS logos, Symbol, DTS-HD and
DTS-HD Master Audio are trademark of DTS, Inc. © 1996-2007
DTS, Inc. All Rights Reserved.
English
3 En
GETTING STARTED
Getting started
■ Installing batteries in the remote control
1
3
2
1
Take off the battery compartment cover.
2
Insert the two supplied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and –) on the inside of the
battery compartment.
3
Snap the battery compartment cover back
into place.
Notes
• Change all of the batteries if you notice that the operation range
of the remote control decreases.
• Do not use an old battery and a new one together.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• If the remote control is without batteries for more than 2
minutes, or if exhausted batteries remain in the remote control,
the contents of the memory may be cleared. When the memory
is cleared, insert new batteries and set up the remote control
code.
4 En
Quick start guide
Quick start guide
Video monitor
Front right
speaker
Front left
speaker
Preparation: Check the items
Subwoofer
Surround right
speaker
Center
speaker
Surround back
right speaker
DVD player
Prepare the following items.
❏ Speakers
❏ Front speakers ................................... x 2
❏ Center speaker .................................. x 1
❏ Surround speakers ............................ x 4
Select magnetically shielded speakers. The
minimum required speakers are two front speakers.
The priority of the requirement of other speakers is
as follows:
Surround back left
speaker
1. Two surround speakers
2. Center speaker
3. One (or two) surround back speaker(s)
Surround left
speaker
Step 1: Set up your speakers
☞ P. 6
Step 2: Connect your DVD player
and other components
☞ P. 7
INTRODUCTION
The following steps describe the easiest way to enjoy DVD movie playback in your home theater. See pages 11 to 15 for
details of the speaker placement.
❏ Active subwoofer ................................... x 1
Select an active subwoofer equipped with an RCA
input jack.
❏ Speaker cables ....................................... x 7
❏ Subwoofer cable .................................... x 1
Select a monaural RCA cable.
❏ DVD player .............................................. x 1
Select DVD player equipped with coaxial digital
audio output jack and composite video output
jack.
❏ Video monitor ......................................... x 1
Select a TV monitor, video monitor or projector
equipped with a composite video input jack.
❏ Video cable ............................................. x 2
Select an RCA composite video cable.
❏ Digital coaxial audio cable .................... x 1
y
Step 3: Press SCENE 1 button
You can also connect two subwoofers to this unit. In this
case, prepare two active subwoofers and subwoofer cables.
☞ P. 8
English
Enjoy DVD playback!
5 En
Quick start guide
Be sure to connect the left channel (L), right channel
(R), “+” (red) and “–” (black) properly.
Step 1: Set up your speakers
Front speakers and center speaker
Place your speakers in the room and connect them to this
unit.
PRE OUT SUBWOOFER 1 jack
AUDIO
MULTI CH INPUT
FRONT (8CH)
CENTER
PRE OUT
SINGLE
DOCK
CENTER
Loosen
Insert
Tighten
VIDEO
VIDEO
L
R
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
DVD
IN
DTV/CBL
DVR
OUT
IN
VCR
OUT
SUB
SB (8CH) SURROUND WOOFER
HDMI
ZONE 2
OUT
FRONT
SURROUND
SUR. BACK
1
2
SUBWOOFER
S VIDEO
DTV/CBL
DVD
PR
SIRIUS
XM
DVD
DTV/CBL
CD
DVD
1
2
3
4
OPTICAL
DVD
IN1
COAXIAL
DIGITAL INPUT
ANTENNA
R EXTRA SP L
FRONT A
R
OUT
SURROUND
R
SURROUND BACK/BI-AMP
L
IN
OUT
MONITOR
DVR
VCR
OUT
COMPONENT VIDEO
DTV/CBL
B PB
Y
Y
PR
MONITOR OUT
CENTER
L
IN
DVD
A PB
OUT
IN2
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
AM
DTV/CBL
R
C
DVR
AC OUTLETS
L
SWITCHED
120V 80Hz
100W MAX. TOTAL
0.8A MAX. TOTAL
GND
FM
75Ω
UNBAL.
REMOTE
IN
OUT
TRIGGER
OUT
+12V
15mA MAX.
SINGLE
Speaker terminals
1
Place your speakers and subwoofer in the
room.
To the front right
speaker
To the center speaker
To the front left
speaker
2
Connect speaker cables to each speaker.
Surround and surround back speakers
Be sure to connect the “+” (red) and “–” (black) properly.
Cables are colored or shaped differently, perhaps with a
stripe, groove or ridge. Connect the striped (grooved, etc.)
cable to the “+” (red) terminals of this unit and your speaker.
Connect the plain cable to the “–” (black) terminals.
3
To the surround
back left speaker
To the surround
right speaker
To the surround
left speaker
4
Connect each speaker cable to the
corresponding speaker terminal of this unit.
To the surround
back right speaker
Connect the subwoofer cable to the
SUBWOOFER PRE OUT 1 jack of this unit
and the input jack of the subwoofer.
Subwoofer
1
2
3
4
AV receiver
DOCK
PRE OUT
SINGLE
1
RROUND
1 Make sure that this unit and the subwoofer are
unplugged from the AC wall outlets.
2 Twist the exposed wires of the speaker cables
together to prevent short circuits.
3 Do not let the bare speaker wires touch each
other.
4 Do not let the bare speaker wires touch any
metal part of this unit.
6 En
SUR. BACK
VIDE
CENTER
2
S VID
DVD
SUBWOOFER
Input jack
Subwoofer cable
SUBWOOFER PRE
OUT 1 jack
y
You can also connect another subwoofer to the SUBWOOFER
PRE OUT 2 jack.
Quick start guide
Step 2: Connect your DVD player
and other components
3
VIDEO MONITOR OUT jack
AV receiver
Video monitor
DVD DIGITAL INPUT COAXIAL jack
DVD VIDEO jack
VIDEO
AUDIO
MULTI CH INPUT
FRONT (8CH)
CENTER
PRE OUT
SINGLE
DOCK
CENTER
VIDEO
VIDEO
L
R
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
IN
DTV/CBL
DVD
DVR
OUT
IN
VCR
OUT
SUB
SB (8CH) SURROUND WOOFER
HDMI
ZONE 2
OUT
SURROUND
FRONT
1
SUR. BACK
S VIDEO
DTV/CBL
DVD
2
SUBWOOFER
PR
IN
OUT
DVD
A PB
IN
OUT
MONITOR
DVR
VCR
OUT
COMPONENT VIDEO
DTV/CBL
B PB
Y
Y
PR
XM
DTV/CBL
CD
1
2
3
OPTICAL
DVD
4
COAXIAL
DIGITAL INPUT
ANTENNA
R EXTRA SP L
DTV/CBL
IN1
IN2
OUT
DVD
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
AM
DVD
FRONT A
R
C
MONITOR OUT
CENTER
L
SURROUND
R
SURROUND BACK/BI-AMP
L
PB
DVR
MONITOR
OUT
OUT
VCR
DVR
VIDEO DTV/CBL
COMPONENT
Y
B PB
PR
Y
AC OUTLETS
L
R
OUT
IN
IN
SIRIUS
DVD
INTRODUCTION
Connect the video cable to the VIDEO
MONITOR OUT jack of this unit and the video
input jack of your video monitor.
SWITCHED
120V 80Hz
100W MAX. TOTAL
0.8A MAX. TOTAL
GND
FM
75Ω
UNBAL.
REMOTE
IN
OUT
C
TRIGGER
OUT
+12V
15mA MAX.
DVR
SINGLE
Video input jack
Video cable
Make sure that this unit and the DVD
player are unplugged from the AC
wall outlets.
4
VIDEO
MONITOR OUT
jack
Connect the power plug of this unit and other
components into the AC wall outlet.
y
This unit is equipped with AC OUTLETS for the power
supply of the other components. See page 28 for details.
1
Connect the digital coaxial audio cable to the
digital coaxial audio output jack of your DVD
player and the DVD DIGITAL INPUT COAXIAL
jack of this unit.
AV receiver
DVD player
M
FRONT (8CH
AUDIO
IN1
COAXIAL
SPEAKERS
OPTICAL
DIGITAL INPUT
E B/
FRONT B/ZON
E
ZONE 2/PRESENC
R EXTRA SP
FRONT A
R
L
CENTER
SU
DVD DIGITAL
INPUT COAXIAL
jack
Connect the video cable to the composite
video output jack of your DVD player and
DVD VIDEO jack of this unit.
AV receiver
• Connecting a DVD player via various ways of the
connection
☞ P. 21
• Connecting a DVD recorder or a digital video
recorder
☞ P. 22
☞ P. 22
• Connecting a CD player, an MD recorder or a
turntable
☞ P. 23
• Connecting an external amplifier
☞ P. 24
• Connecting a DVD player via analog multi-channel
audio connection
☞ P. 25
• Connecting a Yamaha iPod universal dock or
Bluetooth adapter
☞ P. 25
• Using the REMOTE IN/OUT jacks
☞ P. 26
• Using the VIDEO AUX jacks on the front panel
☞ P. 26
VIDEO
DOCK
• Connecting a video monitor via various ways of the
connection
☞ P. 20
• Connecting a set-top box
Digital coaxial audio
cable
DVD player
• Using the other kind of speaker combinations
☞ P. 11
R
L
Digital coaxial
audio output
jack
2
SB (8CH
DVD
6
5
4
OUT
VCR
DVD
CD
3
DVR
DTV/CBL
DVD
IN
OUT
IN
D/ OUT
D-R (REC)
■ For further connections
VIDEO
• Connecting a FM/AM antenna
S VIDEO
DTV/CBL
DVD
PR
☞ P. 27
OUT
IN
DVR
V
COMPONENT
DVD
PR
Y
A PB
• Connecting the XM Mini-Tuner Dock
☞ P. 57
OUT
• Connecting the SiriusConnect tuner
DVD VIDEO jack
☞ P. 62
Video cable
7 En
English
Composite
video output
jack
Quick start guide
Step 3: Press SCENE 1 button
Check the type of the connected speakers.
If the speakers are 6 ohm speakers, set “SP IMP.” to
“6Ω MIN” before using this unit (see page 28). 4 ohm
speakers can be also used as the front speakers (see
page 106).
1
2
Turn on the video monitor and then set the
input source selector of the video monitor to
this unit.
■ About SCENE function
Just by pressing one SCENE button, you can turn on this
unit and recall your favorite input source and sound field
program according to the SCENE template that has been
assigned to the SCENE button. The SCENE templates are
built combinations of input sources and sound field
programs.
y
If you connect a Yamaha product that has capability of the
SCENE control signals, this unit can automatically activate the
component and start playback. Refer to the instruction manual of
the DVD player for further information.
■ The default assigned SCENE templates
Press SSCENE1 button.
This unit is turned on. “DVD Viewing” appears in the
front panel display, and this unit automatically
optimize own status for the DVD playback.
y
The indicator on the selected SCENE button lights up while
this unit is in the SCENE mode.
3
Start playback of the desired DVD on your
player.
4
Rotate JVOLUME to adjust the volume.
Default
SCENE
button
The name of the SCENE template
and its description
SCENE
1
DVD Viewing
– input source: DVD
– sound field program: Straight
For when you want to listen to a music disc from
the connected DVD player as the background
music for this room.
SCENE
2
Disc Listening
– input source: DVD
– sound field program: 7ch Stereo
For when you want to listen to a music disc from
the connected DVD player as the background
music for this room.
SCENE
3
TV Viewing *1
– input source: DTV/CBL
– sound field program: Straight
For when you want to watch a TV program.
SCENE
4
Radio Listening *2, *3, *4
– input source: TUNER
– sound field program: 7ch Enhancer
For when you want to listen to a music program
from the FM radio station.
Note
*1
You must connect a cable TV or a satellite tuner to this unit in
advance. See page 22 for details.
*2 You need to connect the supplied FM and AM antennas to this
unit in advance. See page 27 for details.
*3 You must tune into the desired radio station in advance. See
pages 53 to 56 for tuning information.
*4 To achieve the best possible reception, orient the connected
AM loop antenna, or adjust the position of the end of the
indoor FM antenna.
y
You can change the assigned SCENE template for the SCENE
buttons. See page 37 for details.
Note
When you change the input source or sound field program,
the SCENE mode is deactivated.
8 En
Quick start guide
■ After using this unit...
■ Customizing the SCENE templates
☞ P. 37
• Using various SCENE templates
• Creating your original SCENE templates
☞ P. 40
INTRODUCTION
Press KMAIN ZONE ON/OFF to set this unit to
the standby mode.
What do you want to do with this
unit?
■ Using various input sources
• Basic controls of this unit
☞ P. 42
• Enjoying FM/AM radio programs
☞ P. 53
• Enjoying XM Satellite Radio programs
☞ P. 57
• Enjoying SIRIUS Satellite Radio programs
☞ P. 62
This unit is set to the standby mode and consumes a small
amount of power in order to receive infrared signals from
the remote control. To turn on this unit from the standby
mode, press the desired SSCENE buttons
(or 6 SCENE) or KMAIN ZONE ON/OFF
(or H POWER). See page 29 for details.
• Using your iPod with this unit
☞ P. 68
• Using the Bluetooth components
☞ P. 70
■ Using various sound features
• Using various sound field programs
☞ P. 48
• Using the pure direct mode for high
fidelity sound
☞ P. 52
• Customizing the sound field programs
☞ P. 72
■ Adjusting the parameters of this unit
• Automatically optimizing the speaker parameters
for your listening room (AUTO SETUP) ☞ P. 32
• Manually adjusting various parameters of this unit
☞ P. 80
• Setting the remote control
☞ P. 100
• Adjusting the advanced parameters
☞ P. 106
■ Additional feature
• Automatically turning off this unit
☞ P. 47
English
9 En
CONNECTIONS
Connections
Rear panel
1
2
3
AUDIO
4
5
MULTI CH INPUT
FRONT (8CH)
CENTER
PRE OUT
SINGLE
6
DOCK
CENTER
7
VIDEO
VIDEO
L
R
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
DVD
IN
DTV/CBL
DVR
OUT
IN
VCR
OUT
SUB
SB (8CH) SURROUND WOOFER
HDMI
ZONE 2
OUT
FRONT
SURROUND
SUR. BACK
1
2
SUBWOOFER
S VIDEO
DVD
DTV/CBL
PR
DVD
SIRIUS
DTV/CBL
CD
2
3
1
XM
OPTICAL
DVD
4
R EXTRA SP L
DTV/CBL
IN1
IN
OUT
MONITOR
OUT
IN2
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
AM
OUT
DVR
VCR
OUT
COMPONENT VIDEO
DTV/CBL
B PB
Y
Y
PR
DVD
COAXIAL
DIGITAL INPUT
ANTENNA
IN
DVD
A PB
FRONT A
R
MONITOR OUT
CENTER
L
SURROUND
R
SURROUND BACK/BI-AMP
L
R
C
DVR
AC OUTLETS
L
SWITCHED
120V 80Hz
100W MAX. TOTAL
0.8A MAX. TOTAL
GND
FM
75Ω
UNBAL.
REMOTE
IN
8
OUT
TRIGGER
OUT
+12V
15mA MAX.
SINGLE
9
0
Name
1
2
A
Page
XM jack
(U.S.A. and Canada models only)
57
SIRIUS jack
(U.S.A. and Canada models only)
62
AUDIO jacks
21
DIGITAL INPUT/OUTPUT jacks
17-23
3
MULTI CH INPUT jacks
25
4
ZONE2 OUT jacks
103
5
PRE OUT jacks
24
6
DOCK terminal
25
7
Video component jacks
(VIDEO and S VIDEO)
17-22
COMPONENT VIDEO jacks
17-22
8
ANTENNA terminals
27
9
REMOTE IN/OUT jacks
26
0
Speaker terminals
A
HDMI jacks
18
B
AC OUTLETS
28
10 En
11-16
B
9 TRIGGER OUT jack
This is control expansion jack for custom installation.
Connections
Placing speakers
The speaker layout below shows the speaker setting we recommend. You can use it to enjoy the CINEMA DSP and
multi-channel audio sources.
■ 7.1-channel speaker layout
7.1-channel speaker layout is highly recommended for playback the sound of high definition audio formats (Dolby
TrueHD, DTS-HD Master Audio, etc.) as well as the conventional audio sources with sound field programs. See page 14
for connection information.
y
SW
FL
C
FL
FR
SR
FR
PREPARATION
We recommend that you also add the presence speakers for the effect sounds of the CINEMA DSP sound field program. See page 13 for
details.
30˚
C
SW
SL
SL
SBR
SBL
SR
60˚
SL
SR
80˚
SBL
SBR
30 cm (12 in) or more
Speaker indications
FL/FR: Front left/right
C: Center
SL/SR: Surround left/right
SBL/SBR: Surround back left/right
SW: Subwoofer
Front left and right speakers
The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the
ideal listening position. The distance of each speaker from each side of the video monitor should be the same.
Center speaker
The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a
center speaker, you can do without it. Best results, however, are obtained with the full system.
Surround left and right speakers
The surround speakers are used for effect and surround sounds.
Surround back left and right speakers
The surround back speakers supplement the surround speakers and provide more realistic front-to-back transitions.
y
When you use two subwoofers, select the same type of the subwoofer as another and set these subwoofers as same sound characteristics.
Place each subwoofer at the same distance from the listening position. The signal output at the SUBWOOFER PRE OUT 2 is the same
as the one output at the SUBWOOFER PRE OUT 1 jack.
11 En
English
Subwoofer(s)
The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is
effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the high fidelity
sound of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. You can connect one or
two subwoofer(s) to this unit. When you use two subwoofers, you can enjoy deeper bass sound. The position of the
subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer
near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections.
Connections
■ 6.1-channel speaker layout
■ 5.1-channel speaker layout
See page 14 for connection information.
See page 14 for connection information.
y
y
We recommend that you also add the presence speakers for the
effect sounds of the CINEMA DSP sound field program. See
page 13 for details.
We recommend that you also add the presence speakers for the
effect sounds of the CINEMA DSP sound field program. See
page 13 for details.
FR
FR
SW
FL
SR
SW
FL
C
C
SR
SL
SW
SW
SB
C
FL
FR
30˚
SL
SR
SL
Speaker indications
FL/FR: Front left/right
C: Center
SL/SR: Surround left/right
SB: Surround back
SW: Subwoofer
C
FL
30˚
SL
SR
80˚
FL/FR: Front left/right
C: Center
SL/SR: Surround left/right
SW: Subwoofer
SR
60˚
SL
Speaker indications
FR
60˚
SL
80˚
SR
SB
Front left and right speakers
Center speaker
Surround left and right speakers
Subwoofer(s)
The functions and settings of each speaker are the same as
those for the 7.1-channel speaker layout (see page 11).
Surround back speaker
Connect a single surround speakers to the SURROUND
BACK SINGLE speaker terminal and place the single
surround back speaker behind the listening position. The
surround back left and right channel signals are mixed
down and output at the single surround back speaker when
you set “SUR.B L/R SP” to “SMLx1” or “LRGx1” (see
page 86).
Front left and right speakers
Center speaker
Subwoofer(s)
The functions and settings of each speaker are the same as
those for the 7.1-channel speaker layout (see page 11).
Surround left and right speakers
Connect the surround speakers to the SURROUND
speaker terminals even if you place the surround speakers
behind the listening position. For the smooth and
unbroken sound field behind the listening position, place
the surround left and right speakers farther back compared
with the placement in the 7.1-channel speaker layout. The
surround back channel signals are directed to the surround
left and right speakers when “SUR.B L/R SP” is set to
“NONE” (see page 86).
For other speaker combinations
You can enjoy multi-channel sources with sound field programs by using a speaker combination other than the 7.1/
6.1/5.1-channel speaker combinations.
Use the automatic setup feature (see page 32) or set the “SPEAKER SET” parameters in “MANUAL SETUP” (see
page 85) to output the surround sounds at the connected speakers.
12 En
Connections
■ Using presence speakers
The presence speakers supplement the sound from the front and surround back speakers with extra ambient effects
produced by the sound field programs (see page 48). You can adjust the vertical position of dialogues with using the
presence speakers (see page 73).
To use the presence speakers, connect the speakers to the EXTRA SP terminal (see page 14) and set “EXTRA SP
ASSIGN” to “PRESENCE” (see pages 33 and 85).
0.5 to 1 m (1 to 3 ft)
0.5 to 1 m (1 to 3 ft)
Speaker indications
PL
FL
FR
1.8 m
(6 ft) or
higher
FL: Front left
FR: Front right
C: Center
PL: Front presence left
PR: Front presence right
PREPARATION
1.8 m
(6 ft) or
higher
PR
C
English
13 En
Connections
Connecting speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,
this unit cannot reproduce the input sources accurately.
Caution
• Before connecting the speakers, make sure that the AC power plug is disconnected from the AC wall outlet.
• Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage
this unit and/or the speakers. If the speaker wires are short-circuited, “CHECK SP WIRES” appears in the front
panel display when you turn on this unit.
• Use the magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the
speakers away from the monitor.
• If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6Ω MIN” before using this unit (see page 28). 4 ohm
speakers can be also used as the front speakers. For details about the speaker impedance setting, see page 106.
Note
A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe,
groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the plain cable
to the “–” (black) terminals.
■ For the 7.1-channel speaker setting
EXTRA SP terminals
Connect the alternative front speaker system (FRONT B), front speaker systems in another room
(ZONE B), presence speakers, or Zone 2 speakers. To select the function of the speakers connected
to the EXTRA SP terminals, set the “EXTRA SP ASSIGN” parameter in “SOUND MENU” (see
page 85).
Subwoofers
(optional)
y
You can also select the function of the speakers connected to the EXTRA SP terminals in “AUTO
SETUP” (see page 33).
AUDIO
MULTI CH INPUT
FRONT (8CH)
CENTER
PRE OUT
SINGLE
DOCK
CENTER
VIDEO
VIDEO
L
R
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
DVD
IN
DTV/CBL
DVR
OUT
IN
VCR
OUT
SUB
SB (8CH) SURROUND WOOFER
HDMI
ZONE 2
OUT
FRONT
SURROUND
SUR. BACK
1
2
SUBWOOFER
S VIDEO
DTV/CBL
DVD
PR
DVD
SIRIUS
DTV/CBL
CD
2
3
1
XM
OPTICAL
DVD
4
R EXTRA SP L
DTV/CBL
IN1
FRONT A
R
MONITOR OUT
CENTER
L
SURROUND
R
SURROUND BACK/BI-AMP
L
R
L
AC OUTLETS
SWITCHED
120V 80Hz
100W MAX. TOTAL
0.8A MAX. TOTAL
GND
FM
75Ω
UNBAL.
REMOTE
IN
OUT
TRIGGER
OUT
+12V
15mA MAX.
SINGLE
Center speaker
Left
Right
Front speakers
(FRONT A)
14 En
IN
OUT
OUT
IN2
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
AM
OUT
Left
Right
Surround speakers
Left
Right
Surround back speakers
MONITOR
DVR
VCR
OUT
COMPONENT VIDEO
DTV/CBL
B PB
Y
Y
PR
DVD
COAXIAL
DIGITAL INPUT
ANTENNA
IN
DVD
A PB
C
DVR
Connections
■ For the 6.1-channel speaker setting
Center speaker
EXTRA SP terminals
(see page 14)
(optional)
AUDIO
IN
MD/ OUT
(PLAY) CD-R (REC)
DVD
MULTI CH INPUT
FRONT (8CH)
CENTER
DVD
DTV/CBL
CD
2
3
1
IN
DTV/CBL
OPTICAL
DVR
OUT
IN
VCR
OUT
SUB
SB (8CH) SURROUND WOOFER
HDMI
PRE OUT
SINGLE
ZONE 2
OUT
FRONT
SURROUND
SUR. BACK
DOCK
CENTER
1
2
SUBWOOFER
Subwoofers
DVD
DVD
4
DTV/CBL
IN1
COAXIAL
OUT
IN2
PREPARATION
DIGITAL INPUT
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
FRONT A
R EXTRA SP L
CENTER
SURROUND
L
R
SURROUND BACK/BI-AMP
L
R
R
L
TRIGGER
OUT
2V
5mA MAX.
SINGLE
Right
Left
Surround speakers
Right
Left
Front speakers
(FRONT A)
Left (SINGLE)
Surround back speaker
■ For the 5.1-channel speaker setting
Center speaker
EXTRA SP terminals
(see page 14)
(optional)
AUDIO
IN
MD/ OUT
(PLAY) CD-R (REC)
DVD
1
MULTI CH INPUT
FRONT (8CH)
CENTER
DVD
IN
DTV/CBL
DTV/CBL
CD
2
3
OPTICAL
DVR
OUT
IN
VCR
OUT
ZONE 2
OUT
FRONT
SURROUND
SUR. BACK
DOCK
CENTER
1
2
SUBWOOFER
Subwoofers
DVD
DVD
4
DTV/CBL
IN1
COAXIAL
DIGITAL INPUT
OUT
IN2
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
R EXTRA SP L
SUB
SB (8CH) SURROUND WOOFER
HDMI
PRE OUT
SINGLE
FRONT A
R
CENTER
L
SURROUND
R
SURROUND BACK/BI-AMP
L
R
L
TRIGGER
OUT
2V
mA MAX.
SINGLE
English
Right
Left
Front speakers
(FRONT A)
Right
Left
Surround speakers
15 En
Connections
■ Connecting the speaker cable
1
Remove approximately 10 mm (0.4 in) of
insulation from the end of each speaker
cable and then twist the exposed wires of the
cable together to prevent short circuits.
■ Connecting the banana plug
(U.S.A. and Canada models only)
Tighten the knob and then insert the banana plug
connector into the end of the corresponding
terminal.
10 mm (0.4 in)
2
Loosen the knob.
Red: positive (+)
Black: negative (–)
■ Using bi-amplification connections
Red: positive (+)
Black: negative (–)
3
Insert one bare wire into the hole on the side
of each terminal.
Caution
Remove the shorting bars or bridges of your speakers
to separate the LPF (low pass filter) and HPF (high
pass filter) crossovers.
This unit allows you to make bi-amplification connections
to one speaker system. Check if your speakers support biamplification.
To make the bi-amplification connections, use the FRONT
and SURROUND BACK/BI-AMP terminals as shown
below. To activate the bi-amplification connections, set
“BI-AMP” to “ON” in “ADVANCED SETUP” (see
page 109).
Front speakers
Right
4
Left
Tighten the knob to secure the wire.
FRONT A
R
SURROUND BACK/
BI-AMP
L
R
SINGLE L
This unit
Note
When you make the conventional connection, make sure that the
shorting bars are put into the terminals appropriately. Refer to the
instruction manuals of the speakers for details.
16 En
Connections
Information on jacks and cable plugs
Connect one of the type of the audio jack(s) and/or video jack(s) that your input components are equipped with.
Audio jacks and cable plugs
Video jacks and cable plugs
DIGITAL
R
COAXIAL
OPTICAL
(White)
(Red)
(Orange)
L
R
C
AUDIO
Left and right
analog audio
cable plugs
Coaxial
digital audio
cable plug
VIDEO
S VIDEO
(Yellow)
O
V
S
Optical
digital
audio cable
plug
Composite
video cable
plug
S-video
cable plug
COMPONENT VIDEO
PR
PB
Y
(Red)
(Blue)
(Green)
PR
PB
Y
Component
video cable
plugs
■ Audio jacks
■ Video jacks
This unit has three types of audio jacks. Connection
depends on the availability of audio jacks on your other
components.
This unit has three types of video jacks. Connection
depends on the availability of input jacks on your video
monitor.
AUDIO jacks
For conventional analog audio signals transmitted via left
and right analog audio cables. Connect red plugs to the
right jacks and white plugs to the left jacks.
VIDEO jacks
For conventional composite video signals transmitted via
composite video cables.
DIGITAL COAXIAL jacks
For digital audio signals transmitted via coaxial digital
audio cables.
DIGITAL OPTICAL jacks
For digital audio signals transmitted via optical digital
audio cables.
Note
You can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. When you connect components to both the
COAXIAL and OPTICAL jacks, priority is given to the signals
input at the COAXIAL jack. Optical input jacks are compatible
with digital signals with up to 96 kHz of sampling frequency.
PREPARATION
DIGITAL
L
S VIDEO jacks
For S-video signals, separated into the luminance (Y) and
chrominance (C) video signals transmitted on separate
wires of S-video cables.
COMPONENT VIDEO jacks
For component video signals, separated into the
luminance (Y) and chrominance (PB, PR) video signals
transmitted on separate wires of component video cables.
y
This unit is equipped with the video conversion function. See
pages 19 and 97 for details.
English
17 En
Connections
Information on HDMI™
■ HDMI signal compatibility
Video signals
This unit is compatible with the video signals of the
following resolutions:
Audio signals
Audio signal
types
Audio signal
formats
Compatible
media
2ch Linear
PCM
2ch, 32-192 kHz,
16/20/24 bit
CD, DVD-Video,
DVD-Audio, etc.
Multi-ch
Linear PCM
8ch, 32-192 kHz,
16/20/24 bit
DVD-Audio, Bluray Disc, HD DVD,
etc.
DSD
2/5.1ch,
2.8224 MHz, 1 bit
SA-CD, etc.
Bitstream
Dolby Digital,
DTS
DVD-Video, etc.
Bitstream (High
definition audio)
Dolby TrueHD,
Dolby Digital Plus,
DTS-HD Master
Audio, DTS-HD High
Resolution Audio,
DTS Express
Video signal format
– 480i/60 Hz
– 576i/50 Hz
– 480p/60 Hz
– 576p/50 Hz
– 720p/60 Hz, 50 Hz
– 1080i/60 Hz, 50 Hz
– 1080p/60 Hz, 50 Hz, 24 Hz
Default input assignment of HDMI input jacks
HDMI input jack
Blu-ray Disc,
HD DVD, etc.
Assigned input source
IN1
DVD
IN2
DTV/CBL
■ HDMI jack and cable plug
HDMI
y
• If the input source component can decode the bitstream audio
signals of audio commentaries, you can play back the audio
sources with the audio commentaries mixed down by using the
following connections:
– multi-channel analog audio input (see page 25)
– DIGITAL INPUT OPTICAL (or COAXIAL)
• Refer to the supplied instruction manuals of the input source
component, and set the component appropriately.
Notes
• When CPPM copy-protected DVD-Audio is played back, video
and audio signals may not be output depending on the type of
the DVD player.
• This unit is not compatible with HDCP-incompatible HDMI or
DVI components.
• To decode audio bitstream signals on this unit, set the input
source component appropriately so that the component outputs
the bitstream audio signals directly (does not decode the
bitstream signals on the component). Refer to the supplied
instruction manuals for details.
• This unit is not compatible with the audio commentary features
(for example, the special audio contents downloaded via Internet)
of Blu-ray Disc or HD DVD. This unit does not play back the
audio commentaries of the Blu-ray Disc or HD DVD contents.
18 En
HDMI cable plug
y
• We recommend that you use an HDMI cable shorter than 5
meters (16 feet) with the HDMI logo printed on it.
• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect
this unit to other DVI components.
Notes
• Do not disconnect or connect the cable or turn off the power of
the HDMI components connected to the HDMI OUT jack of
this unit while data is being transferred. Doing so may disrupt
playback or cause noise.
• If you turn off the power of the video monitor connected to the
HDMI OUT jack via a DVI connection, this unit may fail to
establish the connection to the component.
• The analog video signals input at the composite video, S-video
and component video jacks can be digitally up-converted to be
output at the HDMI OUT jack. Set “VIDEO CONV.” to “ON”
in “MANUAL SETUP” (see page 97) to activate this feature.
Connections
Audio and video signal flow
■ Audio signal flow
Input
■ Video signal flow
Output
Input
HDMI
Output
HDMI
COMPONENT
VIDEO
PREPARATION
AUDIO
S VIDEO
VIDEO
Digital output
Through
Analog output
Video conversion ON (see page 97)
Notes
Notes
• 2-channel as well as multi-channel PCM, Dolby Digital and
DTS signals input at one of the HDMI IN jacks can be output at
the HDMI OUT jack only when “S.AUDIO” is set to “OTHER”
(see page 98).
• Audio signals input at the HDMI IN jacks are not output at the
AUDIO output and DIGITAL OUTPUT jacks.
• When the video signals are input at the HDMI, COMPONENT
VIDEO, S VIDEO, and VIDEO jacks, the priority order of the
input signals is as follows:
1. HDMI
2. COMPONENT VIDEO
3. S VIDEO
4. VIDEO
• Digital video signals input at one of the HDMI IN jacks cannot
be output from analog video output jacks.
• The analog component video signals with
480i (NTSC)/576i (PAL) of resolution are converted to the
S-video or composite video signals and output at the S VIDEO
MONITOR OUT and VIDEO MONITOR OUT jacks.
• The analog component video signals with 1080p of resolution
are only output at the COMPONENT VIDEO MONITOR OUT
jacks.
English
19 En
Connections
Connecting a TV monitor or projector
• When you use the internal tuner of the TV as the input source,
connect the digital or analog audio output jacks of the TV and
digital or analog audio input jacks of this unit. Refer to
“Connecting a set-top box” on page 22 for connecting
information.
Connect your TV (or projector) to the HDMI OUT jack,
the COMPONENT VIDEO MONITOR OUT jacks, the
S VIDEO MONITOR OUT jack or the VIDEO
MONITOR OUT jack of this unit.
Notes
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
• If a video monitor is connected to this unit via a DVI
connection, you may not take full advantage of the HDMI
features.
• Some video monitors connected to this unit via a DVI
connection fail to recognize the HDMI audio/video signals
being input if they are in the standby mode. In this case, the
HDMI indicator flashes irregularly.
• If the connected video monitor is compatible with the automatic
audio and video synchronization feature (automatic lip sync
feature), this unit adjusts the audio and video timing
automatically (see page 92). Connect the video monitor to the
HDMI OUT jack of this unit to use the feature.
y
• You can choose to play back HDMI audio signals on this unit or
on another HDMI component connected to the HDMI OUT
jack of this unit. Use the “S.AUDIO” parameter in “OPTION
MENU” to select the component to play back HDMI audio
signals (see page 98).
AUDIO
MD/ OUT
CD-R (REC)
MULTI CH INPUT
FRONT (8CH)
CENTER
DVD
IN
DTV/CBL
DVR
OUT
IN
VCR
OUT
SUB
SB (8CH) SURROUND WOOFER
HDMI
PRE OUT
SINGLE
ZONE 2
OUT
FRONT
SURROUND
SUR. BACK
DOCK
CENTER
1
VIDEO
VIDEO
S VIDEO
DTV/CBL
DVD
2
SUBWOOFER
PR
DVD
1
DTV/CBL
CD
2
3
OPTICAL
OUT
IN
OUT
MONITOR
DVR
VCR
OUT
COMPONENT VIDEO
DTV/CBL
B PB
Y
Y
PR
DVD
DVD
4
DTV/CBL
IN1
COAXIAL
DIGITAL INPUT
OUT
IN2
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
FRONT A
R EXTRA SP L
IN
DVD
A PB
R
MONITOR OUT
CENTER
L
SURROUND
R
SURROUND BACK/BI-AMP
L
R
C
DVR
AC OUTLETS
L
SWITCHED
120V 80Hz
100W MAX. TOTAL
0.8A MAX. TOTAL
O
Optical out
HDMI in
Component video in
S-video in
Video in
TV (or projector)
indicates recommended connections
indicates alternative connections
(One for the video connection, and one for the
audio connection)
20 En
Y
PB
PR
S
V
Connections
Connecting other components
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
Notes
• When “VIDEO CONV.” is set to “OFF” (see page 97), be sure
to make the same type of video connections as those made for
your TV (see page 20). For example, if you connected your TV
to the VIDEO MONITOR OUT jack of this unit, connect your
other components to the VIDEO jacks.
■ Connecting a DVD player
DVD player
Optical out
PREPARATION
• When “VIDEO CONV.” is set to “ON” (see page 97), the
converted video signals are output only at the MONITOR OUT
jacks. To record a source, make the same type of video
connections between each component.
• To make a digital connection to a component other than the
default component assigned to each DIGITAL INPUT or
DIGITAL OUTPUT jack, select the corresponding setting for
“OPTICAL OUT”, “OPTICAL IN”, or “COAXIAL IN” in “I/O
ASSIGNMENT” (see page 93).
• If you connect your DVD player to both the DIGITAL INPUT
(OPTICAL) and the DIGITAL INPUT (COAXIAL) jacks,
priority is given to the signals input at the DIGITAL INPUT
(COAXIAL) jack.
S-video out
Video out
Coaxial out
Component video out
Audio out
L
C
O
HDMI out
R
PR
AUDIO
MULTI CH INPUT
FRONT (8CH)
CENTER
PRE OUT
SINGLE
PB
Y
V
DOCK
CENTER
S
VIDEO
VIDEO
L
R
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
DVD
IN
DTV/CBL
DVR
OUT
IN
VCR
OUT
SUB
SB (8CH) SURROUND WOOFER
HDMI
ZONE 2
OUT
FRONT
SURROUND
SUR. BACK
1
2
SUBWOOFER
S VIDEO
DTV/CBL
DVD
PR
DVD
SIRIUS
1
XM
DTV/CBL
CD
2
3
OPTICAL
DVD
4
R EXTRA SP L
DTV/CBL
IN1
IN
OUT
MONITOR
OUT
IN2
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
AM
OUT
DVR
VCR
OUT
COMPONENT VIDEO
DTV/CBL
B PB
Y
Y
PR
DVD
COAXIAL
DIGITAL INPUT
ANTENNA
IN
DVD
A PB
FRONT A
R
MONITOR OUT
CENTER
L
SURROUND
R
SURROUND BACK/BI-AMP
L
R
L
C
DVR
AC OUTLETS
SWITCHED
120V 80Hz
100W MAX. TOTAL
0.8A MAX. TOTAL
GND
FM
75Ω
UNBAL.
REMOTE
IN
OUT
TRIGGER
OUT
+12V
15mA MAX.
indicates recommended connections
indicates alternative connections
(One for the video connection, and one for the
audio connection)
English
21 En
Connections
■ Connecting a DVD recorder, PVR or VCR
S-video out
VCR
Audio out
S-video in
Audio in
R
L
R
AUDIO
Video in
Video out
L
MULTI CH INPUT
FRONT (8CH)
CENTER
PRE OUT
SINGLE
DOCK
CENTER
V
V
IN
OUT
S
S
VIDEO
VIDEO
L
R
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
IN
DTV/CBL
DVD
OUT
DVR
IN
VCR
OUT
SUB
SB (8CH) SURROUND WOOFER
HDMI
ZONE 2
OUT
FRONT
SURROUND
SUR. BACK
1
S VIDEO
DVD
DTV/CBL
2
SUBWOOFER
PR
DVD
1
XM
DTV/CBL
CD
2
3
OPTICAL
DVD
4
DTV/CBL
IN1
MONITOR
OUT
IN2
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
FRONT A
C
MONITOR OUT
SURROUND
SURROUND BACK/BI-AMP
R
DVR
AC OUTLETS
S
V
S-video out
L
R
CENTER
Video out
L
OUT
DVR
VCR
OUT
COMPONENT VIDEO
DTV/CBL
B PB
Y
Y
PR
DVD
COAXIAL
DIGITAL INPUT
ANTENNA
IN
DVD
A PB
S
V
Y
PB
PR
S-video in
Audio in
Video in
Audio out
Component video out
DVD recorder
or PVR
■ Connecting a set-top box
Satellite receiver, cable
TV receiver or HDTV
decoder
S-video out
Optical out
Video out
Component video out
Audio out
HDMI out
R
O
L
AUDIO
Y
MULTI CH INPUT
FRONT (8CH)
CENTER
PRE OUT
SINGLE
PB
PR
DOCK
CENTER
V
S
VIDEO
VIDEO
L
R
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
DVD
DTV/CBL
IN
DVR
OUT
IN
VCR
OUT
SUB
SB (8CH) SURROUND WOOFER
HDMI
ZONE 2
OUT
FRONT
SURROUND
SUR. BACK
1
2
SUBWOOFER
S VIDEO
DVD
DTV/CBL
PR
DVD
SIRIUS
XM
ANTENNA
1
DTV/CBL
CD
2
3
OPTICAL
FRONT B/ZONE B/
OUT
IN
OUT
MONITOR
DVR
VCR
OUT
COMPONENT VIDEO
DTV/CBL
B PB
Y
Y
PR
DVD
4
COAXIAL
DIGITAL INPUT
IN
DVD
A PB
DVD
DTV/CBL
IN1
IN2
SPEAKERS
OUT
MONITOR OUT
C
DVR
indicates recommended connections
indicates alternative connections
(One for the video connection, and one for the
audio connection)
22 En
Connections
■ Connecting audio components
Notes
• To make a digital connection to a component other than the default component assigned to each the DIGITAL INPUT jack, select the
corresponding setting for “OPTICAL IN”, or “COAXIAL IN” in “I/O ASSIGNMENT” (see page 93).
• When you connect both the DIGITAL INPUT (OPTICAL) jack and the DIGITAL INPUT (COAXIAL) jack to an audio component,
the priority is given to the DIGITAL INPUT (COAXIAL) jack.
CD recorder, MD
recorder or tape deck
PREPARATION
Audio out
Audio in
L
R
L
R
AUDIO
MULTI CH INPUT
FRONT (8CH)
CENTER
PRE OU
L
R
CD
IN
MD/ OUT
(PLAY) CD-R (REC)
DVD
SIRIUS
1
XM
DVD
IN
DTV/CBL
DTV/CBL
CD
2
3
OPTICAL
DVR
OUT
IN
VCR
DVD
4
R EXTRA SP L
ZONE 2
OUT
FRONT
SURROUND
S
DTV/CBL
IN1
OUT
IN2
SPEAKERS
FRONT B/ZONE B/
ZONE 2/PRESENCE
AM
SUB
SB (8CH) SURROUND WOOFER
HDMI
DVD
COAXIAL
DIGITAL INPUT
ANTENNA
OUT
FRONT A
R
CENTER
L
SURROUND
R
SURROUND BACK/BI-AMP
L
R
L
GND
FM
75Ω
UNBAL.
REMOTE
IN
OUT
L
TRIGGER
OUT
+12V
15mA MAX.
R
C
Coaxial
out
Audio
out
CD player
indicates recommended connections
indicates alternative connections
(One for the audio connection)
English
23 En
Connections
■ Connecting an external amplifier
This unit has more than enough power for any home use. However, if you want to add more power to the speaker output
or if you want to use another amplifier, connect an external amplifier to the PRE OUT jacks. Each PRE OUT jack outputs
the same channel signals as the corresponding SPEAKERS terminals.
Notes
•
•
•
•
When you make connections to the PRE OUT jacks, do not make connections to the SPEAKERS terminals.
The signals output at the FRONT PRE OUT jacks are affected by the TONE CONTROL settings (see page 52).
Adjust the volume level of the subwoofer with the control on the subwoofer (see page 52).
Some signals may not be output at the SUBWOOFER PRE OUT jacks depending on the settings for “SPEAKER SET” (see page 85).
PRE OUT
SINGLE
5
CENTER
L
R
FRONT
SURROUND
1
2
SUR. BACK
3
1
2
SUBWOOFER
4
1 FRONT PRE OUT jacks
Front channel output jacks.
2 SURROUND PRE OUT jacks
Surround channel output jacks.
3 SUR.BACK PRE OUT jacks
Surround back channel output jacks. When you only
connect one external amplifier for the surround back
channel, connect it to the SINGLE jack.
Notes
• When “BI-AMP” is set to “ON”, this unit outputs the front
channel audio signals at the SUR.BACK PRE OUT jacks.
• The audio signals output at the SUR.BACK PRE OUT jacks
differ depending on the “EXTRA SP ASSIGN” setting (see
pages 33 and 85).
4 SUBWOOFER PRE OUT jacks
Connect one or two subwoofers with a built-in amplifier.
Note
The signal output at the SUBWOOFER PRE OUT 2 is the same
as the one output at the SUBWOOFER PRE OUT 1 jack.
5 CENTER PRE OUT jack
Center channel output jack.
24 En
Connections
■ Connecting a multi-format player or an external decoder
This unit is equipped with 6 additional input jacks (left and right FRONT, CENTER, left and right SURROUND and
SUBWOOFER) for discrete multi-channel input from a multi-format player, external decoder, sound processor or preamplifier.
If you set “INPUT CH” to “8CH” in “MULTI CH” (see page 95), you can use the input jacks assigned as “FRONT” in
“MULTI CH” (see page 95) together with the MULTI CH INPUT jacks to input 8-channel signals.
Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to
match the left and right outputs to the left and right input jacks for the front and surround channels.
Notes
MULTI CH INPUT
FRONT (8CH)
CENTER
MULTI CH INPUT
FRONT (8CH)
CENTER
L
L
L
R
R
*1
R
L
R
L
L
R
L
R
Center out
Subwoofer
out
Front out
Center out
Subwoofer
out
Front out
Multi-format player/External
decoder (5.1-channel output)
*1
R
SUB
SB (8CH) SURROUND WOOFER
Surround out
R
Surround out
L
Surround back out
SUB
SB (8CH) SURROUND WOOFER
PREPARATION
• When you select the component connected to the MULTI CH INPUT jacks as the input source (see page 43), this unit automatically
turns off the digital sound field processor, and you cannot select sound field programs.
• This unit does not redirect signals input at the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that
you connect at least a 5.1-channel speaker system before using this feature.
Multi-format player/External
decoder (7.1-channel output)
The analog audio input jacks assigned as “FRONT” in “MULTI CH” (see page 95).
■ Connecting a Yamaha iPod universal
dock or Bluetooth adapter
This unit is equipped with the DOCK terminal on the rear
panel that allows you to connect a Yamaha iPod universal
dock (such as YDS-10, sold separately) or Bluetooth
adapter (such as YBA-10 sold separately). Connect a
Yamaha iPod universal dock or Bluetooth adapter to the
DOCK terminal on the rear panel of this unit using its
dedicated cable.
DOCK
Refer to “Using iPod™” on page 68 for playback of your iPod
and “Using Bluetooth™ components” on page 70 for playback of
your Bluetooth components.
VIDEO
VIDEO
S VIDEO
DVD
DTV/CBL
PR
y
IN
DVD
A PB
OUT
IN
OUT
MONITOR
DVR
VCR
OUT
COMPONENT VIDEO
DTV/CBL
B PB
Y
Y
PR
MONITOR OUT
C
DVR
English
Yamaha iPod universal dock
or Bluetooth adapter
25 En
Connections
■ Using REMOTE IN/OUT jacks
When the components are the Yamaha products and have
the capability of the transmission of the remote control
signals, connect the REMOTE IN jack and REMOTE
OUT jack to the remote control input and output jack with
the monaural analog mini cable as follows.
IN
OUT
Use the VIDEO AUX jacks on the front panel to connect a
game console or a video camera to this unit.
Caution
Be sure to turn down the volume of this unit and other
components before making connections.
FM
75Ω
UNBAL.
REMOTE
Using the VIDEO AUX jacks on the
front panel
TRIGGER
OUT
+12V
15mA MAX.
Notes
Remote
control out
Remote
control in
• The audio signals input at the DOCK terminal on the rear panel
take priority over the ones input at the VIDEO AUX jacks.
• To reproduce the source signals input at these jacks, select
“V-AUX” as the input source.
VOLUME
SPEAKERS
Infrared signal
receiver or Yamaha
component
Yamaha component
(CD or DVD player,
etc.)
EDIT
SEARCH MODE
BAND
CATEGORY
A/B/C/D/E
PRESET/TUNING/CH
MEMORY
INFO
ZONE 2
ON/OFF
ZONE 2
CONTROL
SCENE
1
2
3
4
PROGRAM
SYSTEM OFF
PHONES
TONE CONTROL
INPUT
STRAIGHT
PURE DIRECT
AUDIO SELECT
VIDEO AUX
OPTIMIZER MIC
STANDBY
/ON
SILENT CINEMA
EFFECT
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
y
VIDEO
L
S
V
L
AUDIO
R
OPTICAL
R
O
Audio output
Video output
Optical output
S VIDEO
S-Video output
• If the components have the capability of the SCENE control
signals, this unit can automatically activate the corresponding
components and start the playback when you use one of the
SCENE buttons. Refer to the owner’s manuals for details about
the capability of the SCENE control signals of the components.
• If the component connected to the REMOTE OUT jack is not
the Yamaha product, set “SCENE IR” in the advanced setup
menu to “OFF” (see page 109).
Game console or
video camera
indicates recommended connections
indicates alternative connections
(One for the video connection, and
one for the audio connection)
26 En
Connections
Connecting the FM and AM
antennas
Connecting the wire of the AM loop antenna
Open the lever
Insert
Close the lever
Both FM and AM indoor antennas are supplied with this
unit. Connect each antenna correctly to the designated
terminals. In general, these antennas should provide
sufficient signal strength.
Notes
y
The wire of the AM loop antenna does not have any polarity
and you can connect either end of the wire to AM or GND
terminal.
Assembling the supplied AM loop antenna
PREPARATION
• The AM loop antenna should be placed away from this unit.
• A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality,
install an outdoor antenna. Consult the nearest authorized
Yamaha dealer or service center about outdoor antennas.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
AM loop antenna
(supplied)
Indoor FM
antenna
(supplied)
DV
SIRIUS
1
XM
OPT
ANTENNA
F
Z
AM
GND
FM
75Ω
UNBAL.
REMOTE
TRIGGER
OUT
Outdoor AM antenna
Use a 5 to 10 m (16 to 33
ft) vinyl-covered wire
extended outdoors from a
window.
Ground (GND terminal)
For maximum safety and minimum interference, connect the
antenna GND terminal to a good earth ground. A good earth
ground is a metal stake driven into moist earth.
English
27 En
Connections
Connecting the power cable
MONITOR OUT
C
DVR
AC OUTLETS
Setting the speaker impedance
Caution
If you are to use 6 ohm speakers, set “SP IMP.” to
“6Ω MIN” as follows BEFORE using this unit. 4 ohm
speakers can be also used as the front speakers.
SWITCHED
120V 80Hz
100W MAX. TOTAL
0.8A MAX. TOTAL
1
Press LSYSTEM OFF on the front panel to
turn off this unit.
See page 29 for details.
2
Press and hold MTONE CONTROL and
then press KMAIN ZONE ON/OFF to turn
on this unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
To the AC wall outlet
TONE CONTROL
While holding
down
MAIN ZONE
ON/OFF
■ AC OUTLETS (SWITCHED)
Use these 2 outlets to supply power to any connected
components. Connect the power cable of your other
components to these 2 outlets. Power to these 2 outlets is
supplied when this unit is turned on. However, power to
these 2 outlets is cut off when this unit is turned off. For
information on the maximum power or the total power
consumption of the components that can be connected to
these 2 outlets, see “Specifications” on page 124.
3
Rotate the NPROGRAM selector to select
“SP IMP.”.
“SP IMP.” and the current speaker impedance setting
(“8Ω MIN”) appear in the front panel display.
4
Press MTONE CONTROL repeatedly to
select “6Ω MIN”.
5
Press LSYSTEM OFF to save the new
setting and turn off this unit.
Note
The power to AC OUTLETS of this unit is not cut off while this
unit is charging connected iPod even when this unit is in the
standby mode. When this unit completes charging or the iPod is
disconnected, the power is cut off automatically when this unit is
in the standby mode.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, the stored data will be lost in case the power
cable is disconnected from the AC wall outlet or if the
power supply is cut off for more than one week.
28 En
Note
The setting you made is reflected next time you turn on this
unit.
Connections
Turning this unit on and off
■ Turning on this unit
Press KMAIN ZONE ON/OFF (or H POWER) to
turn on this unit.
The main zone is turned on.
y
PREPARATION
• When you turn on this unit, there will be delay for a few
seconds before this unit can reproduce sound.
• You can also turn on the main zone by pressing SSCENE (or
6SCENE) buttons.
■ Set the main zone to the standby mode
Press KMAIN ZONE ON/OFF (or ISTANDBY)
to set the main zone to the standby mode.
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
y
Press L SYSTEM OFF to set the main zone and Zone 2 (see
page 104) to the standby mode simultaneously.
English
29 En
Connections
Front panel display
1
2
MULTI CH
VCR
3
DVR
q EX ADAPTIVE DRC
MASTER AUDIO q DIGITAL PLUS
HD 96 q TRUE HD
ES 24 q PL x
MATRIX DISCRETE
4
V-AUX
DOCK
SP
AB
5
DTV/CBL
6
DVD
MD/CD-R
ENHANCER
7
CD
8
TUNER
XM
ZONE 2
SILENT CINEMA
ft
ms
dB
A
B C
DE
F
1 HDMI indicator
Lights up when the signal of the selected input source is
input at the HDMI IN jacks (see page 18).
2 ADAPTIVE DRC indicator
Lights up when the adaptive dynamic range control
feature is turned on (see page 89).
SIRIUS
VOL.
YPAO MEMORY
VIRTUAL AUTO TUNED STEREO MUTE
dB
HOLD
SLEEP
96/24 LFE
neural
PCM DSD
0
9
G
H
L C R
SL SB SR
SBL
SBR
I
7 Tuner indicators
Lights up when this unit is in the FM, AM, XM Satellite
Radio, or SIRIUS Satellite Radio tuning mode (see
pages 53 to 67).
8 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
3 DOCK indicator
• Lights up when you station your iPod in a Yamaha
iPod universal dock (such as YDS-10, sold separately)
connected to the DOCK terminal of this unit (see
page 25) and V-AUX is selected as the input source.
The DOCK indicator also lights up when this unit is
charging the battery of the stationed iPod in the
standby mode.
• Flashes while the connected Yamaha Bluetooth adapter
(such as YBA-10, sold separately) and the Bluetooth
component is in the paring or the Bluetooth adapter is
searching the Bluetooth component (see page 70).
• Light up while the Yamaha Bluetooth adapter is
connected to the Bluetooth component (see page 70).
9 MUTE indicator and VOLUME level indicator
• The MUTE indicator flashes while the MUTE function
is on (see page 45).
• Indicates the current volume level.
4 ENHANCER indicator
Lights up when the Compressed Music Enhancer mode is
selected (see page 50).
The neural indicator is only applicable to the U.S.A. and
Canada models and CSII indicator is only applicable to
the U.S.A. model.
5 Input source indicators
The corresponding cursor lights up to show the currently
selected input source.
B Sound field indicators
Light up to indicate the active sound fields (see page 48).
Note
The XM and SIRIUS indicator is only applicable to the U.S.A.
and Canada models and the cursor on the left of the XM indicator
or SIRIUS indicator lights up only when “XM” or “SIRIUS” is
selected as the input source.
6 YPAO indicator
Lights up when you run “AUTO SETUP” and when the
speaker settings set in “AUTO SETUP” are used without
any modifications (see page 32).
30 En
0 Input signal indicators
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) or DSD (Direct Stream Digital) digital audio
signals.
A Decoder indicators
The respective indicator lights up when any of the
decoders of this unit function.
Note
Presence sound field
Listening position
Surround left
sound field
Surround right
sound field
Surround back sound field
C Headphone indicator
Lights up when headphones are connected (see page 45).
Connections
D SP A B indicators
Light up according to the set of front speakers activated
(see page 43).
SP A: The FRONT A speakers are activated.
SP B: The FRONT B speakers are activated.
SP A B: The FRONT A and FRONT B speakers are
activated.
Using the remote control
The remote control transmits a directional infrared ray.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
Remote control sensor
E ZONE2 indicator
Lights up when Zone 2 is turned on (see page 104).
CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound
field program (see page 48).
Approximately 6 m (20 ft)
30
PREPARATION
F DSP indicators
The respective indicator lights up when any of the sound
field programs are selected (see page 48).
30
VIRTUAL indicator
Lights up when the Virtual CINEMA DSP mode is
active (see page 51).
SILENT CINEMA indicator
Lights up when headphones are connected and a
sound field program is selected (see page 51).
G Multi-information display
Shows the name of the current sound field program and
other information when adjusting or changing settings.
H SLEEP indicator
Lights up while the sleep timer is on (see page 47).
I Input channel and speaker indicators
LFE indicator
LFE
L C R
SL SB SR
SBL
SBR
Presence speaker indicators
Input channel indicators
1Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
I
y
To set the remote control codes for other components, see
page 102.
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperature, such as near a heater or stove
– places of extremely low temperatures
– dusty places
Input channel indicators
• Indicate the channel components of the current
digital input signal.
• Light up or flash according to the settings of the
speakers when this unit is in the automatic setup
procedure (see page 32) or in the “BASIC MENU”
in “MANUAL SETUP” (see page 87).
Presence speaker indicators
Light up or flash according to the setting of “EXTRA
SP ASSIGN” when this unit is in the automatic setup
procedure (see page 32) or in the “BASIC MENU” in
“MANUAL SETUP” (see page 85).
English
y
You can make settings for the presence and surround back
speakers automatically by running “AUTO SETUP” (see
page 32) or manually by adjusting settings for “SUR.B L/R
SP” (see page 86) in “SPEAKER SET”.
31 En
OPTIMIZING THE SPEAKER SETTING FOR YOUR LISTENING ROOM (YPAO)
Optimizing the speaker setting for your listening room (YPAO)
This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid
troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied
optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening
environment.
Using AUTO SETUP
2
Notes
• Be advised that it is normal for loud test tones to be output
during the “AUTO SETUP” procedure.
• To achieve the best results, make sure the room is as quiet as
possible while the “AUTO SETUP” procedure is in progress. If
there is too much ambient noise, the results may not be
satisfactory.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
“MIC ON View OSD menu” appears in the front
panel display.
VIDEO AUX
OPTIMIZER MIC
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
y
• Initial settings are indicated in bold.
• You can run “AUTO SETUP” using the system menu that
appears in the OSD or in the front panel display. This manual
uses the OSD illustrations to explain the “AUTO SETUP”
procedure.
• Before performing operations, press 5AMP.
• This unit uses the speakers connected to the FRONT A speaker
terminals as the front speakers for the adjustment.
1
Omni-directional
microphone
The following menu screen appears on the video
monitor.
AUTOSETUP
. EXTRASPASSIGN
>ZONE2
FRONTB
ZONEBPRESENCE
NONE
SETUP;;;;;;;AUTO
EQ;;;;;;;NATURAL
START
Make sure of the following check points.
Note
❏
❏
Speakers are connected appropriately.
Headphones are disconnected from this unit.
This unit and the video monitor are turned on.
This unit is selected as the video input source of
the video monitor.
The connected subwoofer is turned on and the
volume level is set to about half way (or slightly
less).
The crossover frequency controls of the
connected subwoofer is set to the maximum.
VOLUME
MIN
MAX
[]/[]:Up/Down
[]/[]:Select
[ [
3
[
❏
❏
❏
❏
[
Before starting the automatic setup, check the following
check points.
Place the optimizer microphone at your
normal listening position on a flat level
surface with the omni-directional
microphone heading upward.
Optimizer microphone
CROSSOVER
HIGH CUT
MIN
MAX
Controls of a subwoofer (example)
❏
The room is sufficiently quiet.
y
If you connect two subwoofers to this unit, the volume level
of each subwoofer is set to slightly less.
32 En
y
It is recommended that you use a tripod (etc.) to affix the
optimizer microphone at the same height as your ears would
be when you are seated in your listening position. You can
use the attached screw of a tripod (etc.) to fix the optimizer
microphone to the tripod (etc.).
Optimizing the speaker setting for your listening room (YPAO)
4
Notes
Press 8l / h to select the desired setting
for “EXTRA SP ASSIGN” and then press 8n.
Extra speaker assignment
EXTRA SP ASSIGN
Selects the function of the speakers connected to the
EXTRA SP terminals.
Choices: FRONT B, ZONE2, ZONE B,
PRESENCE, NONE
• When you use the Zone 2 speakers (see
page 104)
Select “ZONE2” to set the function of the speakers
to the Zone 2 speakers. This unit drives the Zone 2
speakers by using the internal amplifier.
• When you want to use another front
speaker system in Zone B
Select “ZONE B”.
• When you use the presence speakers (see
page 13)
Select “PRESENCE” to set the function of the
speakers to the presence speakers.
• When you do not use the EXTRA SP
terminals
Select “NONE” to deactivate the EXTRA SP
terminals.
Note
6
Press 8l / h to select the desired setting of
“EQ”.
Parametric equalizer type EQ
Parametric equalizer adjusts the level of the specified
frequency bands. This unit automatically selects the
crucial frequency bands for the listening room and
adjusts the level of the selected frequency bands to
create a cohesive sound field in the room. You can
select the type of the parametric equalizer adjustment
from the following choices.
Choices: NATURAL, FLAT, FRONT
• Select “NATURAL” to average out the frequency
response of all speakers with higher frequencies
being all speakers to achieve more natural sound.
Recommended if the FLAT setting sounds a little
harsh.
• Select “FLAT” to average the frequency response
of all speakers. Recommended if all of your
speakers are of similar quality.
• Select “FRONT” to adjust the frequency response
of each speaker in accordance with the sound of
your front speakers. Recommended if your front
speakers are of much higher quality than your other
speakers.
PREPARATION
• When you use the alternative front speaker
system (see page 43)
Select “FRONT B”.
• “RELOAD” or “UNDO” is available only when you have
previously run “AUTO SETUP” and confirmed the results.
• “RELOAD” or “UNDO” is not available when you change
the setting of “BI-AMP” in the advanced setup (see
page 109) or “EXTRA SP ASSIGN” in “BASIC MENU”
(see page 85).
If you select “ON” in “BI-AMP” (see page 109), you cannot
select “PRESENCE” or “ZONE2” in “EXTRA SP ASSIGN”.
5
Press 8l / h to select “SETUP” and then
press 8n.
Choices: AUTO, RELOAD, UNDO, DEFAULT
• Select “AUTO” to automatically run the entire
“AUTO SETUP” procedure.
• Select “RELOAD” to reload the last “AUTO
SETUP” settings and override the previous
settings.
• Select “UNDO” to undo the last “AUTO SETUP”
settings and restore the previous settings.
• Select “DEFAULT” to reset the “AUTO SETUP”
parameters to the initial factory settings.
English
33 En
Optimizing the speaker setting for your listening room (YPAO)
7
Press 8n to select “START” and then press
8ENTER to start the setup procedure.
The following message appears in the OSD.
When this unit starts the automatic setup procedure,
loud test tones are output at the speakers.
For more accurate measurements, keep quiet and
move to the wall where speakers are not around. We
recommend that you leave the listening room during
the automatic setup procedure.
9
Make sure that the following screen appears
and then press 8ENTER to display the
result screen.
AUTOSETUP
Measurement Complete
Press [ENTER]
NOTICE
Loudtesttonesare
output.
Pleasekeepquiet
orleavetheroom.
AUTOSETUP
RESULT
SP :
3/4/0.1
DIST: 14.0/17.0ft
LVL : -9.0/+6.5dB
. > SET CANCEL
Press[ENTER]
Once you perform the next operation, this unit starts
the automatic setup procedure.
8
Press 8ENTER to start the automatic setup
procedure.
The following screen appears in the OSD and setup
procedure starts in 10 seconds.
AUTOSETUP
MeasurementStart
in 9seconds
[RETURN]:Cancel
Loud test tones are output from each speaker during
the auto setup procedure. Once all items are set, the
“RESULT” display appears in the OSD.
[ ]/[ ]:Up/Down
[ENTER]:Enter
The results displayed under “RESULT” are as
follows:
Number of speakers SP
Displays the number of speakers connected to this
unit in the following order:
Front/Back/Subwoofer
Speaker distance DIST
Displays the speaker distance from the listening
position in the following order:
Closest speaker distance/Farthest speaker distance
Speaker level LVL
Displays the speaker output level in the following
order:
Lowest speaker output level/Highest speaker output
level
Notes
• During the automatic setup procedure, do not perform any
operation on this unit.
• We recommend that you get out of the room while this unit
is in the auto setup procedure. It takes approximately 3
minutes for this unit to complete the auto setup procedure.
y
Press 8k to cancel the automatic setup procedure.
34 En
Notes
• The signal output at the SUBWOOFER PRE OUT 2 jack
is the same as the one output at the SUBWOOFER PRE
OUT 1 jack. Therefore, even if you connect two
subwoofers, the number of the connected subwoofer is
indicated as “0.1”.
• If “E-10:INTERNAL ERROR” appears during the testing
procedure, restart from step 4.
• If you selected other than “AUTO” in step 5, no test tones
are output.
• If an error occurs during the “AUTO SETUP” procedure,
the setup procedure is canceled and an error screen
appears. For details, see “If an error screen appears” on
page 36.
• When this unit detects potential problems during the
“AUTO SETUP” procedure, “WARNING” and the
number of warning messages appears in the above of
“RESULT” (see page 36).
• Depending on the listening environment, “SWFR
PHASE:REV” appears during the automatic procedure
and “SUBWOOFER PHASE” in “SOUND MENU” (see
page 87) is automatically set to “REVERSE”.
Optimizing the speaker setting for your listening room (YPAO)
10
Notes
Press 8k and then 8ENTER to display the
setup results in detail.
• The distances displayed in the “DISTANCE” results may
be longer than the actual distance depending on the
characteristics of your subwoofer.
• In the “EQ” results, different values may be set for the
same frequency to provide finer adjustments.
AUTOSETUP
. RESULT
SP :
3/4/0.1
DIST: 14.0/17.0ft
LVL : -9.0/+6.5dB
> SET CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Detail
12
Press 8ENTER to return to the top
result display.
PREPARATION
AUTOSETUP
RESULT
WIRING
RESULT
SP :
3/4/0.1
DIST: 14.0/17.0ft
LVL : -9.0/+6.5dB
. > SET CANCEL
FRONT L;;;;;;;OK
[ ]/[ ]:Up/Down
[ENTER]:Enter
[[]/[[]:Select
[ENTER]:Return
11
13
Press 8l / h repeatedly to toggle between
the setup result displays.
Press 8k / n to toggle between the parameters in a
results.
Make sure the pointer is pointing at “SET”
and “CANCEL” and then press 8l / h to
select “SET” or “CANCEL”.
AUTOSETUP
Results of the speaker
connection and wiring
(WIRING)
RESULT
SP :
3/4/0.1
DIST: 14.0/17.0ft
LVL : -9.0/+6.5dB
. > SET CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
Choices: SET, CANCEL
• Select “SET” to confirm the “AUTO SETUP”
results.
• Select “CANCEL” to cancel the “AUTO SETUP”
results.
Results of the speaker distance
from the listening position
(DISTANCE)
Results of the setting of each
speaker size
(SIZE)
14
Press 8ENTER to confirm your selection.
The following screen appears. Disconnect the
optimizer microphone from this unit. The optimizer
microphone is sensitive to heat. Keep it away from
direct sunlight and do not place it on top of this unit.
AUTOSETUP
Results of the parametric
equalizer of each speaker
(EQ)
AUTOSETUPComplete
Disconnect Microphone
PRESS [ENTER]
[MENU]:Exit
Results of the speaker output level
(LEVEL)
English
y
If you are not satisfied with the results or want to manually
adjust each parameter, use “MANUAL SETUP” (see
page 80).
35 En
Optimizing the speaker setting for your listening room (YPAO)
15
Press 8ENTER to confirm your selection.
The top “SET MENU” screen appears in the OSD.
SET MENU
. ;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
16
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
Press MMENU to exit from “SET MENU”.
■ If “WARNING” appears
When this unit detects potential problems during the
“AUTO SETUP” procedure, “WARNING” appears in the
top result display. Check the warning messages to correct
your speaker settings.
Note
Warnings differ from errors in that warnings do not cancel the
“AUTO SETUP” procedure.
1
y
If you change speakers, speaker positions, or the layout of your
listening environment, run “AUTO SETUP” again to recalibrate
your system.
Make sure the pointer is pointing at
“WARNING” and then press 8ENTER to
display the detailed information about the
warning.
The number on the right of “WARNING” indicates
the number of warning messages.
■ If an error screen appears
AUTOSETUP
. WARNING(3)
RESULT
SP :
3/4/0.1
DIST: 14.0/17.0ft
LVL : -9.0/+6.5dB
>SET CANCEL
Press 8k / n / l / h to select “RETRY” or
“EXIT” and then press 8ENTER.
The following display is an example when “E-9:USER
CANCEL” appears in the OSD.
ERROR
. E-9:USER CANCEL
Don't operate
any function
>RETRY
[ ]/[ ]:Up/Down
[ENTER]:Detail
2
Press 8l / h repeatedly to toggle between
the warning displays.
EXIT
WARNING
[[]/[[]:Select
[ENTER]:Enter
W-1:OUTOFPHASE
Reverse Channel
FL
-CENTER
PL
PR
SL
SR
SBL
SBR
[[]/[[]:Select
[ENTER]:Return
Choices: RETRY, EXIT
• Select “RETRY” to retry the “AUTO SETUP”
procedure.
• Select “EXIT” to exit from the “AUTO SETUP”
procedure.
y
• For details about each warning message, see the “AUTO
SETUP” section in “Troubleshooting” on page 117.
• When the corresponding warning message is not
applicable to a speaker, “––” is displayed instead.
• If “SWFR: TOO LOUD” or “SWFR: TOO LOW” appears
in the “W-3: LEVEL ERROR” display, adjust the volume
level of the subwoofer(s).
y
If “E-5:NOISY” appears, “PROCEED” also appears in the
choices. When you select “PROCEED”, this unit continues the
measurements and settings, but the settings may not be optimal.
3
36 En
Press 8ENTER to return to the top result
display.
SELECTING THE SCENE TEMPLATES
Selecting the SCENE templates
This unit is equipped with 18 preset SCENE templates for
various situations of using this unit. As the initial factory
setting, the following SCENE templates are assigned to
each SCENE button (see page 8):
2
Rotate the RINPUT selector (or press
5AMP and then press 8l / h) to select the
desired template.
SCENE 1: DVD Viewing
SCENE 2: Disc Listening
SCENE 3: TV Viewing
SCENE 4: Radio Listening
DVD MovieView
If you want to use other SCENE templates, you can select
the desired SCENE templates from the SCENE template
library and assign the templates to the selected SCENE
buttons on the front panel and the remote control.
3
Press the SSCENE (or 6SCENE) button
again to confirm the selection.
The selected SCENE template is assigned to the
SCENE button.
Select the desired SCENE
template
Front panel
or
1
BASIC
OPERATION
1
Remote control
1
Note
Assign the
SCENE
template to the
SCENE button
SCENE template library
(Image)
Once the desired SCENE templates are assigned to the
corresponding SCENE buttons, you need to set the input
source of the SCENE template on the remote control. See
page 41 for details.
Selecting the desired SCENE
template to the SCENE buttons
1
Press and hold the SSCENE (or 6SCENE)
button for 3 seconds.
The indicator on the selected SCENE button on the
front panel starts to flash, and the name of the
currently assigned SCENE template appears in the
front panel display.
3 seconds
3 seconds
or
1
1
Remote control
Front panel
1
Flashes
English
DVD Viewing
37 En
Selecting the SCENE templates
■ Which SCENE template would you like to select?
Which source do you like to
play back?
Video sources
(DVD video,
Recorded video)
Which component do you
like for playback?
DVD
SCENE templates
Default
SCENE buttons
DVD Viewing
1
DVD Movie Viewing
DVD Live Viewing
Music discs (CD, SACD or DVD-Audio)
DVR
DVR Viewing
DVD
Disc Hi-fi Listening
Music Disc Listening
Disc Listening
CD
2
CD Hi-fi Listening
CD Listening
CD Music Listening
Radio programs
TUNER (FM/AM)
Radio Listening
XM
XM Listening
SIRIUS
SIRIUS Listening
iPod or Bluetooth
component
DOCK*
Dock Listening
TV programs
DTV/CBL
TV Viewing
4
3
TV Sports Viewing
Video games
V-AUX*
Action Game Playing
RPG Playing
Note
*
When iPod is connected to the Yamaha iPod universal dock or a Bluetooth component is connected to the Bluetooth adapter, this unit
plays back the audio sources input at the DOCK terminal.
y
You can create your original SCENE templates by editing the preset SCENE templates. See page 40 for details.
38 En
Selecting the SCENE templates
■ Preset SCENE templates descriptions
The illustrations of the SCENE button in the following table indicate the assigned SCENE buttons in the default setting.
SCENE template
Input source
Playback mode
Features
DVD Viewing
DVD*
Straight
DVD Movie Viewing
DVD*
MOVIE
Sci-Fi
Select this SCENE template when you play back movies on
your DVD player.
DVD Live Viewing
DVD*
ENTERTAINMENT
Music Video
Select this SCENE template when you enjoy the music live
video on your DVD player.
DVR Viewing
DVR
MOVIE
Drama
Select this SCENE template when you play back movies on
your digital video recorder.
Disc Hi-fi Listening
DVD*
Pure Direct
Select this SCENE template when you enjoy the high fidelity
sound of the music discs on your DVD player.
Music Disc
Listening
DVD*
STEREO
2ch Stereo
Select this SCENE template when you play back music discs
on your DVD player.
Disc Listening
DVD*
STEREO
7ch Stereo
Select this SCENE template when you play back music
sources on your DVD player as the background music.
CD Hi-fi Listening
CD*
Pure Direct
Select this SCENE template when you enjoy the high fidelity
sound of the music discs on your CD player.
CD Listening
CD*
STEREO
7ch Stereo
Select this SCENE template when you play back music discs
on your CD player.
CD Music Listening
CD*
STEREO
2ch Stereo
Select this SCENE template when you play back music source
on your CD player as the background music.
Radio Listening
TUNER
Select this SCENE template when you play back general
contents on the DVD player.
1
BASIC
OPERATION
2
MUSIC ENHANCER Select this SCENE template when you enjoy FM or AM radio
programs.
7ch Enhancer
4
XM Listening
XM
SIRIUS Listening
SIRIUS
MUSIC ENHANCER Select this SCENE template when you enjoy SIRIUS Satellite
Radio programs.
7ch Enhancer
Dock Listening
V-AUX
MUSIC ENHANCER Select this SCENE template when you play back music on
your iPod stationed in a Yamaha iPod universal dock or
7ch Enhancer
MUSIC ENHANCER Select this SCENE template when you enjoy XM Satellite
Radio programs.
7ch Enhancer
Bluetooth component that is connected to the Bluetooth
adapter.
TV Viewing
DTV/CBL
Straight
TV Sports Viewing
DTV/CBL
ENTERTAINMENT
Sports
Select this SCENE template when you enjoy sports programs
on your TV.
Action Game
Playing
V-AUX
ENTERTAINMENT
Action Game
Select this SCENE template when you play action games such
as car racing and FPS games.
RPG Playing
V-AUX
ENTERTAINMENT
Roleplaying Game
Select this SCENE template when you play role-playing
games.
Select this SCENE template when you enjoy general
programs on your TV.
3
*
When the connected DVD player or CD player has the capability of the SCENE control signals and is connected to the REMOTE
OUT jack of this unit, this unit operates the DVD player or CD player worked with the SCENE features.
English
39 En
Selecting the SCENE templates
Creating your original SCENE
templates
3
You can create your original SCENE templates for each
SCENE button. You can refer to the preset 18 SCENE
templates to create the original SCENE templates.
Select the desired SCENE
template
Create an original SCENE
template
Press 8k / n to select the desired parameter
of the SCENE template and then 8l / h to
select the desired value of the selected
parameter.
You can adjust the following parameters for a SCENE
template:
• INPUT: The input source component.
• MODE: The active sound field programs,
“Straight” or “Pure Direct” mode.
4
Press the 6SCENE button again to confirm
the edit.
SCENE : DVD Viewing
SCENE : DVD Viewing
INPUT : DVD
y
SCENE template library
(Image)
An asterisk mark (*) appears by the name of the original SCENE
template.
Notes
1
Assign the SCENE
template to the
SCENE button
1
Turn on the video monitor connected to this
unit.
2
Press and hold the desired 6SCENE button
for 3 seconds.
The SCENE template customizing screen appears on
the video monitor.
[
SCENE1
.pDVDViewing[
INPUT: DVD
MODE:STRAIGHT
[ENTER]:Rename
[SCENE1]:SET
[RETURN]:EXIT
• Once the desired SCENE templates are assigned to the
corresponding 6SCENE buttons, you need to set the input
source of the SCENE template on the remote control. See
page 41 for details.
• You can create a customized SCENE template for each SCENE
button, and if you create another customized SCENE template,
this unit overwrites the old customized SCENE template with
the new one.
• The newly created template is only available for the assigned
SCENE button.
■ Rename the SCENE templates
Select the name of the SCENE template at step 3
of “Creating your original SCENE templates” and
then press 8ENTER.
Note
When the SCENE template you want to customize is not
assigned to any of the 6SCENE buttons, press 8l / h
repeatedly to recall the desired SCENE template on the
menu screen.
40 En
[
p
SCENE1
RENAME
DVDViewing
[]/[]:Character
[p]/[[]:Position
[ENTER]:SET
[RETURN]:CANCEL
• Press 8k / n to select the desired character.
• Press 8l / h to place an “_” (underscore) under the
space or the desired character.
• Press 9RETURN to cancel the new name.
• Press 8ENTER to confirm the new name.
Selecting the SCENE templates
Using the remote control for the SCENE feature
■ Controlling the input source
components in the SCENE mode
■ Setting input source of the customized
SCENE template on the remote control
You can operate both this unit and the input source
component by using the remote control. You must set the
appropriate remote control code for each input source in
advance (see page 102).
If you customize the input source of the selected SCENE
template, you must set the input source of the SCENE
template on the remote control to operate the input source
component correctly.
1
Press the desired 6SCENE button on the
remote control.
Press and hold the 6SCENE button and the
desired input selector button (4) for 3 seconds.
2
Press the desired buttons in the * area below
to control the input source component of the
selected SCENE template.
y
POWER
STANDBY
POWER
AV
A
XM
SIRIUS
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
VCR
B
AMP
TV INPUT
TV MUTE
1
2
BASIC
OPERATION
*
POWER
TV
Press the 6SCENE button again to operate the input source
component.
TV CH
TV VOL
SCENE
3
4
SCENE buttons
SRCH MODE
VOLUME
MENU
BAND LEVEL
TITLE
ENTER
DISPLAY
RETURN
MEMORY
REC
INFO
l
1
PROG h
2
ENHANCER SUR. DECODE
3
STRAIGHT PURE DIRECT
5
6
9
0
4
PARAMETER
7
MULTI CH IN AUDIO SEL
10
8
SLEEP
ENT
Note
*
These buttons control the input source component. See
page 100 for details of the function of each button.
English
41 En
PLAYBACK
Playback
Caution
Extreme caution should be exercised when you play
back CDs encoded in DTS. If you play back a CD
encoded in DTS on a DTS-incompatible CD player,
you will only hear some unwanted noise that may
damage your speakers. Check whether your CD player
supports CDs encoded in DTS. Also, check the sound
output level of your CD player before you play back a
CD encoded in DTS.
3
Start playback on the selected source
component or select a broadcast station.
• Refer to the operating instructions for the source
component.
• See page 53 for details about FM or AM tuning
instructions.
• See page 58 for details about XM Satellite Radio
tuning instructions.
• See page 63 for details about SIRIUS Satellite
Radio tuning instructions.
• See page 68 for details about iPod operations.
• See page 70 for details about Bluetooth component
operations.
4
Rotate JVOLUME (or press NVOLUME +/–)
to adjust the volume to the desired output
level.
y
To play DTS-encoded CDs when using a digital audio
connection, set “DECODER MODE” in “INPUT MENU” to
“DTS” before the playback (see page 94).
Before performing the following operations, press 5AMP on
the remote control.
Basic procedure
1
y
Turn on the video monitor connected to this
unit.
y
See page 46 to display the input source information on the
video monitor.
2
• See page 52 to adjust the level of each speaker.
• This does not affect the AUDIO OUT (REC) level.
• You can set the initial volume level and maximum volume
level (see page 89).
Rotate the RINPUT selector (or press one
of the input selector buttons (4)) to select
the desired input source.
5
Rotate the NPROGRAM selector (or press
BPROG l / h repeatedly) to select the
desired sound field program.
The name of the selected sound field program appears
in the front panel display. See page 48 for details
about sound field programs.
The name of the currently selected input source
appears in the front panel display for a few seconds.
Available input sources
MULTI CH
VCR
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
CD
TUNER
Sci-Fi
XM
SIRIUS
Currently selected sound field program
DVD
Currently selected input source
y
The corresponding input selector button on the remote
control for the currently selected input source lights up for
approximately 5 seconds after you press any buttons on the
remote control, showing which source component is
currently being operated.
42 En
Note
Sound field programs cannot be selected when the
component connected to the MULTI CH INPUT jacks is
selected as the input source (see page 43).
y
• Choose a sound field program based on your listening
preference, not merely on the name of the program.
• When you select an input source, this unit automatically
selects the last sound field program used with the
corresponding input source.
• To display information about the currently selected sound
field program in the OSD, see page 72 for details.
Playback
Before performing the following operations, press 5AMP on
the remote control.
Selecting the MULTI CH INPUT
component
Use this feature to select the component connected to the
MULTI CH INPUT jacks (see page 25) as the input
source.
Selecting the front speaker set
Use this feature to turn the front speaker system (FRONT
A and/or FRONT B) on or off.
Press ASPEAKERS on the front panel
repeatedly to turn on or off the set of front
speakers connected to the FRONT A and/or
EXTRA SP speaker terminals.
The active front speaker set changes as follows.
Rotate the RINPUT selector to select “MULTI
CH” (or press EMULTI CH IN).
“MULTI CH” appears in the front panel display.
FRONT A
OFF
y
Use “MULTI CH” menu in “INPUT MENU” to set the
parameters for MULTI CH INPUT (see page 95).
FRONT B
FRONT A
and
FRONT B
Notes
Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the input
source.
• FRONT A and B or FRONT B setting is not available when
“EXTRA SP ASSIGN” is set to “PRESENCE”, “ZONE 2” or
“NONE” (see page 85).
• Turn off the volume level of this unit when you switch the front
speaker setting.
BASIC
OPERATION
Note
■ Using the Zone B feature
When you set “EXTRA SP ASSIGN” to “ZONE B” (see
page 85), you can use the speakers connected to the
EXTRA SP speaker terminals in another room (Zone B).
Press ASPEAKERS on the front panel
repeatedly to turn on or off the Zone B speakers.
When you activate the Zone B speakers, all the speakers in
the main room are muted.
Note
If you select the sound field program and activate the Zone B
speakers, Virtual CINEMA DSP activates automatically (see
page 51).
English
43 En
Playback
Before performing the following operations, press 5AMP on
the remote control.
Selecting audio input jacks
(AUDIO SELECT)
Displaying the current status of
this unit on a video monitor
You can display the operating information of this unit on a
video monitor.
This unit comes with a variety of input jacks. Use this
feature (audio input jack select) to switch between input
jacks when more than one input jack is assigned to the
same input source.
y
1
Turn on the video monitor connected to this
unit.
2
Press ODISPLAY on the remote control.
The current status screen appears in the OSD.
• We recommend that you set the audio input jack select to
“AUTO” in most cases.
• You can adjust the default audio input jack select of this unit by
using “AUDIO SELECT” in “OPTION MENU” (see page 98).
Press QAUDIO SELECT (or FAUDIO SEL)
repeatedly to select the desired audio input jack
select setting.
Available input sources
MULTI CH
VCR
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
CD
TUNER
XM
SIRIUS
A.SEL:AUTO
Currently selected audio input jack select setting
AUDIO SELECT
Function
AUTO
Automatically selects input signals in the
following order:
(1) HDMI
(2) Digital signals
(3) Analog signals
HDMI
Selects only HDMI signals. When HDMI
signals are not input, no sound is output.
COAX/OPT
Automatically selects input signals in the
following order:
(1) Digital signals input at the COAXIAL
jack
(2) Digital signals input at the OPTICAL
jack
When no signals are input, no sound is
output.
ANALOG
Selects only analog signals. If no analog
signals are input, no sound is output.
Note
This feature is not available when no digital input jacks
(OPTICAL, COAXIAL and HDMI) are assigned. In addition,
HDMI is not available as an audio input jack select setting when
the HDMI IN jacks are not used. Use “I/O ASSIGNMENT” in
“INPUT MENU” to reassign the respective input jack (see
page 93).
44 En
STATUSVOL:-40.0dB
MOVIE
Sci-Fi
INPUT:DVD
A.SEL:HDMI
[DISPLAY]:STATUSOFF
y
• You can select the amount of time that the current status is
displayed in the OSD by using the “OSD-AMP” parameter
in “OPTION MENU” (see page 96).
• To turn off the status screen, press ODISPLAY again.
Note
The OSD signal is not output at the DVR and VCR VIDEO
OUT jacks and will not be recorded.
Playback
Using your headphones
Before performing the following operations, press 5AMP on
the remote control.
Connect a pair of headphones with a stereo
analog audio cable plug to the PHONES jack on
the front panel.
You can combine a video image from a video source with
sound from an audio source. For example, you can enjoy
listening to classical music while viewing beautiful
scenery from the video source on the video monitor.
VOLUME
SPEAKERS
EDIT
SEARCH MODE
BAND
CATEGORY
A/B/C/D/E
PRESET/TUNING/CH
MEMORY
INFO
MUTE
Playing video sources in the
background of an audio source
SLEEP
SCENE
1
2
3
4
PROGRAM
PHONES
TONE CONTROL
INPUT
STRAIGHT
PURE DIRECT
AUDIO SELECT
VIDEO AUX
OPTIMIZER MIC
STANDBY
/ON
SILENT CINEMA
EFFECT
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
Press the input selector buttons (4) on the
remote control to select a video source and then
an audio source.
SIRIUS
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
VCR
DVD
DTV/CBL
Audio sources
BASIC
OPERATION
XM
Video sources
y
When you select a sound field program, SILENT CINEMA mode
activates automatically (see page 51).
Notes
DVR
Video sources
• When you connect headphones, no signals are output at the
speaker terminals.
• All Dolby Digital and DTS audio signals are mixed down to the
left and right headphone channels.
V-AUX/DOCK
Muting the audio output
VCR
MULTI CH IN
9
Audio sources
y
Press JMUTE on the remote control to mute the
audio output.
Press JMUTE again to resume the audio output.
y
• You can also select “MULTI CH” as the audio source (see
page 43). Press 5AMP and then press EMULTI CH IN.
• Set the “BGV” parameter in the “MULTI CH” menu to the
desired setting to select the default background video input
source of the MULTI CH INPUT sources (see page 95).
• You can also rotate JVOLUME (or press NVOLUME +/–) to
resume the audio output.
• You can adjust the muting level by using the “MUTE TYPE”
parameter in “VOLUME MENU” (see page 89).
• The MUTE indicator flashes in the front panel display when the
audio output is muted and disappears from the front panel
display when the audio output is resumed.
English
45 En
Playback
Displaying the input source
information
You can display the audio and video information of the
current input signal.
1
Press 5AMP and then press MMENU on
the remote control.
The top “SET MENU” display appears in the OSD.
SET MENU
Notes
“–––” appears when this unit cannot display the corresponding
information.
■ Video information
Information
HDMI SIGNAL
Type of the source video signals and
the video signals output at the HDMI
OUT jack of this unit.
HDMI RES.
Resolution of the input signal (analog
or HDMI) and the output signal
(HDMI). When input video signals are
composite video or S-video signals,
the input video signals are indicated as
“Composite” or “S-Video”.
ANALOG RES.
Resolution of the analog video signals
output at the COMPONENT VIDEO
MONITOR OUT jacks of this unit.
HDMI ERROR
(HDMI MESSAGE)
Error message for HDMI sources or
connected HDMI devices.
. ;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
2
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
Press 8n repeatedly to select “SIGNAL
INFO” and then press 8ENTER.
The audio information about the input source appears
in the OSD.
Descriptions
Note
3
Press 8l / h to toggle between the audio
and video information displays.
4
Press MMENU on the remote control again
to exit from “SET MENU”.
“–––” appears when this unit cannot display the corresponding
information.
HDMI error and message
Message
DEVICE OVER
HDCP ERROR
HDCP authentication failed.
Out of Res.
Out of resolution. The connected monitor is
not compatible with the resolution of the
input video signal.
■ Audio information
Information
Descriptions
FORMAT
Signal format. When this unit cannot detect a
digital signal, it automatically switches to
analog input.
SAMPLING
The number of samples per second taken from
a continuous signal to make a discrete signal.
CHANNEL
The number of source channels in the input
signal (front/surround/LFE). For example, a
multi-channel soundtrack with 3 front
channels, 2 surround channels and LFE, is
displayed as “3/2/0.1”.
BITRATE
The number of bits passing a given point per
second.
FLAG
Flag data encoded in DTS, Dolby Digital, or
PCM signals that cue this unit to automatically
switch decoders (“Surround EX”, etc.).
46 En
Cause
The number of the connected HDMI
components is over the limit.
Playback
■ Canceling the sleep timer
Using the sleep timer
Use this feature to automatically set the main zone to the
standby mode after a certain amount of time. The sleep
timer is useful when you are going to sleep while this unit
is playing or recording a source. The sleep timer also
automatically turns off any external components
connected to the AC OUTLETS (see page 28).
Press TSLEEP on the remote control repeatedly
until “SLEEP OFF” appears in the front panel
display.
Disappears
Note
SLEEP
Even if this unit is in the standby mode, this unit does not cut off
the power to AC OUTLETS while charging connected iPod (see
page 28).
Press 5AMP and then press TSLEEP
repeatedly to set the amount of time.
Each time you press TSLEEP, the front panel display
changes as shown below.
SLEEP OFF
The SLEEP indicator turns off, and “SLEEP OFF”
disappears from the front panel display after a few
seconds.
y
The sleep timer setting can also be canceled by pressing
ISTANDBY (or KMAIN ZONE ON/OFF) to set the main
zone to the standby mode.
BASIC
OPERATION
SLEEP 120min
OFF
SLEEP 90min
SLEEP 30min
SLEEP 60min
The SLEEP indicator flashes while you are switching the
amount of time for the sleep timer. Once the sleep timer is
set, the SLEEP indicator lights up in the front panel
display, and the display returns to the selected sound field
program.
Flashes
SLEEP
SLEEP 120min.
Lights up
SLEEP
Straight
English
47 En
SOUND FIELD PROGRAMS
Sound field programs
This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from
almost any stereo or multi-channel sound source. This unit is also equipped with a Yamaha digital sound field processing
(DSP) chip containing several sound field programs which you can use to enhance your playback experience.
Selecting sound field programs
Rotate the NPROGRAM selector (or press
5AMP and then press BPROG l / h
repeatedly).
The name of the selected sound field program appears in
the front panel display and in the OSD.
Notes
• When you select an input source, this unit automatically selects
the last sound field program used with the corresponding input
source.
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 43).
• When you play back the Dolby TrueHD, Dolby Digital Plus,
DTS-HD Master Audio, or DTS-HD High Resolution Audio
sources, this unit does not activate any sound field program.
• When the sampling frequency of the input sources are higher
than 96 kHz, this unit does not apply any sound field programs.
Sound field program descriptions
y
Select a sound field program based on your listening preference, not merely on the name of the program, etc.
■ For audio music sources
y
For audio music sources, we also recommend that you use the Pure Direct mode (see page 52).
Notes
• The available sound field parameters differ depending on the settings of the speakers.
• “DIALG.LIFT” is available only when “EXTRA SP ASSIGN” in “SPEAKER SET” is set to “PRESENCE” (see page 85).
CLASSICAL
Program
Descriptions
Hall in Munich
This sound field simulates a concert hall with approximately 2500 seats in Munich, using stylish
wood for the interior finishing as normal standards for European concert halls. Fine, beautiful
reverberations spread richly, creating a calming atmosphere. The listener’s virtual seat is at the
center left of the arena.
Hall in Vienna
This is an approximately 1700-seated, middle-sized concert hall with a shoebox shape that is
traditional in Vienna. Pillars and ornate carvings create extremely complex reflections from all
around the audience, producing a very full, rich sound.
Chamber
This program creates a relatively wide space with a high ceiling like an audience hall in a palace. It
offers pleasant reverberations that are suitable for courtly music and chamber music.
48 En
Sound field programs
LIVE/CLUB
Program
Descriptions
Cellar Club
This program simulates a live house with a low ceiling and homey atmosphere. A realistic, live sound
field features powerful sound as if the listener is in a row in front of a small stage.
The Roxy Theatre
This is the sound field of a rock music live house in Los Angeles, with approximately 460 seats. The
listener’s virtual seat is at the center left of the hall.
The Bottom Line
This is the sound field at stage front in The Bottom Line, that was a famous New York jazz club once. The
floor can seat 300 people to the left and right in a sound field offering real and vibrant sound.
■ For various sources
Notes
• The available sound field parameters and the created sound fields differ depending on the input sources and the settings of this unit.
• “DIALG.LIFT” is available only when “EXTRA SP ASSIGN” in “SPEAKER SET” is set to “PRESENCE” (see page 85).
ENTERTAINMENT
Program
Descriptions
Action Game
This sound field has been suitable for action games such as car racing and FPS games. It uses the
reflection data that limits the effects range per channel in order to offer a powerful playing environment
with a being-there feeling by enhancing various effects tones while maintaining a clear sense of
directions.
Roleplaying Game
This sound field has been suitable for role-playing and adventure games. It combines the sound field
effects for movies and the sound field designs for “Action Game” to represent the depth and 3D feeling of
the field during play, while offering movie-like surround effects in the movie scenes in the game.
Music Video
This sound field offers an image of a concert hall for live performance of pop, rock and jazz music. The
listener can indulge oneself in a hot live space thanks to the presence sound field that emphasizes the
vividness of vocals and solo play and the beat of rhythm instruments, and to the surround sound field that
reproduces the space of a big live hall.
BASIC
OPERATION
Sports
This program allows the listeners to enjoy stereo sport broadcasts and studio variety programs with
enriched live feeling. In sports broadcasts, the voices of the commentator and sportscaster are positioned
clearly at the center while the atmosphere of the stadium expands in an optimum space to offer the
listeners with a feeling of presence in the stadium.
■ For movie sources
y
You can select the desired decoder used with following sound field program (except “Mono Movie”). See page 77 for details.
Notes
• The available sound field parameters and the created sound fields differ depending on the input sources and the settings of this unit.
• “DIALG.LIFT” is available only when “EXTRA SP ASSIGN” in “SPEAKER SET” is set to “PRESENCE” (see page 85).
MOVIE
Program
Descriptions
Spectacle
This program represents the spectacular feeling of large-scale movie productions.
It reproduces a broad theater sound field matching the cinemascope and wider-screen movies with an
excellent dynamic range from very small to extremely large sound.
Sci-Fi
This program clearly reproduces the finely elaborated sound design of the latest science fiction and
special effects-featuring movies.
You can enjoy a variety of cinematographically created virtual spaces reproduced with clear separation
between dialog, sound effects and background music.
49 En
English
Standard
This program creates a sound field emphasizing the surrounding feeling without disturbing the original
acoustic positioning of multi-channel audio such as Dolby Digital and DTS. It has been designed with the
concept of “an ideal movie theater”, in which the audience is surrounded by beautiful reverberations from
the left, right and rear.
Sound field programs
Program
Descriptions
Adventure
This program is ideal for precisely reproducing the sound design of action and adventure movies.
The sound field restrains reverberations but puts emphasis on reproducing a powerful space expanded
widely to the left and right. The reproduced depth is also restrained relatively to ensure the separation
between audio channels and the clarity of the sound.
Drama
This sound field features stable reverberations that match a wide range of movie genres from serious
dramas to musicals and comedies. The reverberations are modest but offer an optimum 3D feeling,
reproducing effects tones and background music softly but cubically around clear words and center
positioning in a way that does not fatigue the listener even after long hours of viewing.
Mono Movie
This program is provided for reproducing monaural video sources such as a classic movie in an
atmosphere of a good old movie theater.
The program produces the optimum expansion and reverberation to the original audio to create a
comfortable space with a certain sound depth.
Note
The available parameters differ depending on the input sources and the settings of this unit.
STEREO
Program
Descriptions
2ch Stereo
Use this program to mix down multi-channel sources to 2 channels.
7ch Stereo
Use this program to output sound from all speakers. When you play back multi-channel sources, this unit
downmixes the source to 2 channels, and then outputs the sound from all speakers. This program creates
a larger sound field and is ideal for background music at parties, etc.
■ The Compressed Music Enhancer
MUSIC ENHANCER
Program
Descriptions
Straight Enhancer
Use this program to enhance the sound nearest to the original depth and width of the 2-channel or multichannel compression artifacts.
7ch Enhancer
Use this program to play back compression artifacts in 7-channel stereo.
■ Surround decode mode
SUR. DECODE
Program
Sur. Decoder
50 En
Descriptions
Select this program to playback sources with selected decoders. You can playback 2-channel sources on
multi-channels. See page 78 for details.
Sound field programs
■ Using sound field programs without
surround speakers
(Virtual CINEMA DSP)
Virtual CINEMA DSP allows you to enjoy the CINEMA
DSP programs without surround speakers. It creates
virtual speakers to reproduce the natural sound field.
When you set “SUR. L/R SP” to “NONE” (see page 86),
Virtual CINEMA DSP activates automatically whenever
you select a sound field program (see page 48).
Note
Virtual CINEMA DSP will not activate even when “SUR. L/R
SP” is set to “NONE” (see page 86) in the following cases:
– when the component connected to the MULTI CH INPUT
jacks is selected as the input source (see page 43).
– when headphones are connected to the PHONES jack.
– when this unit is in the “7ch Stereo” mode.
SILENT CINEMA allows you to enjoy multi-channel
music or movie sound, including Dolby Digital and DTS
sources, through ordinary headphones. SILENT CINEMA
activates automatically whenever you connect headphones
to the PHONES jack while listening to sound field
programs (see page 48). When activated, the SILENT
CINEMA indicator lights up in the front panel display.
Enjoying unprocessed input
sources (Straight decoding mode)
When this unit is in the “Straight” mode, 2-channel stereo
sources are output from only the front left and right
speakers. Multi-channel sources are decoded straight into
the appropriate channels without any additional effect
processing.
Press OSTRAIGHT (or CSTRAIGHT) to select
“Straight”.
■ Deactivating the “Straight” mode
Press OSTRAIGHT (or CSTRAIGHT) so that
“Straight” disappears from the front panel
display.
The sound effect is turned back on.
BASIC
OPERATION
■ Enjoying multi-channel sources and
sound field programs with headphones
(SILENT CINEMA)
Before performing the following operation, press 5AMP on
the remote control.
Notes
• SILENT CINEMA does not activate when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 43).
• SILENT CINEMA is not effective when the “Pure Direct” (see
page 52) or “2ch Stereo” mode (see page 50) is selected, or
when this unit is in the “Straight” mode (see page 51).
English
51 En
USING AUDIO FEATURES
Using audio features
Before performing the following operations, press 5AMP on
the remote control.
Adjusting the speaker level
You can adjust the output level of each speaker while
listening to a music source. This is also possible when
playing sources input at the MULTI CH INPUT jacks.
Note
This operation will override the level adjustments made in
“AUTO SETUP” (see page 32) and “SP LEVEL” (see page 87).
1
Press 7LEVEL on the remote control and
then 8k / n repeatedly to select the speaker
you want to adjust.
Enjoying pure hi-fi sound
Use the Pure Direct mode to enjoy the pure high fidelity
sound of the selected source. When the Pure Direct mode
is activated, this unit plays back the selected source with
the least circuitry.
Press PPURE DIRECT (or DPURE DIRECT)
to turn the Pure Direct mode on or off.
The PPURE DIRECT button on the front panel lights up
while this unit is in the Pure Direct mode. The front panel
display automatically dims.
Notes
FRONT L
Front left speaker
FRONT R
Front right speaker
• The following operations are not possible when this unit is in
the Pure Direct mode:
– switching the sound field program
– displaying the OSD
– adjusting the “SET MENU” parameters (except for level
settings)
– operating video functions (video conversion, etc.)
• The Pure Direct mode is automatically canceled whenever this
unit is turned off.
CENTER
Center speaker
y
SUR. L
Surround left speaker
The front panel display turns on momentarily when an operation
is performed.
SUR. R
Surround right speaker
SBL
Surround back left speaker
SBR
Surround back right speaker
SWFR
Subwoofer
PRNS L
Presence left speaker
Speaker and headphone adjustments are stored independently.
PRNS R
Presence right speaker
1
Press MTONE CONTROL on the front
panel repeatedly to select the high-frequency
response (TREBLE) or the low-frequency
response (BASS).
2
Rotate the NPROGRAM selector to adjust
the high-frequency response (TREBLE) or
the low-frequency response (BASS).
Control range: –6 dB to +6 dB
Display
Adjusted speaker
Adjusting the tonal quality
Use this feature to adjust the balance of bass and treble for
the front left and right speaker channels.
y
y
• The available speaker channels differ depending on the
setting of the speakers.
• When the video monitor is turned on, the “LEVEL”
adjustment menu appears in the video monitor.
2
3
Press 8l / h to adjust the speaker output
level.
• Press 8h to increase the value.
• Press 8l to decrease the value.
Control range: –10.0 dB to +10.0 dB
Press 7LEVEL to turn off the speaker level
adjustment display.
52 En
Notes
• If you increase or decrease the high-frequency or the low-frequency
sound to an extreme level, the tonal quality of the surround
speakers may not match.
• TONE CONTROL is not effective when PURE DIRECT is
selected, or when MULTI CH INPUT is selected as the input
source.
FM/AM TUNING
FM/AM tuning
Overview
You can use two tuning modes to tune into the desired FM/AM station:
Frequency tuning mode (AUTO TUNING/MANUAL TUNING)
You can search or specify the frequency of the desired FM/AM station automatically or manually (see “Basic tuning
operations” on this page).
Preset tuning mode (PRESET TUNING)
You can preset the desired FM/AM station in advance, and then recall the station by specifying the preset group and
number (see “Using station preset feature” on page 54).
Note
Orient the connected FM and AM antennas for the best reception.
Before performing the following operations, press 4TUNER
on the remote control.
1
Rotate the RINPUT selector (or press
4TUNER) to select “TUNER” as the input
source.
AFM 88.9MHz
No colon (:)
2
Press CBAND (or 7BAND) to select the
reception band.
“FM” or “AM” appears in the front panel display.
y
3
Press BSEARCH MODE (or MSRCH
MODE) to select the desired tuning mode.
Preset tuning mode (PRESET TUNING)
Use this feature to recall the preset stations. When
this unit is in the preset tuning mode, “PRESET
TUNING” appears in the front panel display for a
moment. Frequency tuning is not possible. See
page 54 for details.
Automatic tuning mode (AUTO TUNING)
Use this feature when the signal from the station you
want to select is strong.
When this unit is in the automatic tuning mode,
“AUTO TUNING” appears in the front panel display
for a moment. The AUTO indicator appears in the
front panel display.
Lights up
BASIC
OPERATION
Manual tuning mode (MANUAL TUNING)
Use this feature if the signal from the station you
want to select is weak and you cannot tune by using
the automatic tuning. When this unit is in the manual
tuning mode, “MANUAL TUNING” appears in the
front panel display for a moment.
Basic tuning operations
Manually tuning into an FM station automatically switches
the tuner to monaural reception to increase the signal
quality.
4
Press EPRESET/TUNING/CH l / h (or
8PRESET/CH k / n) repeatedly to tune into
the desired station.
• Press Eh (or 8k) to tune into a higher
frequency.
• Press El (or 8n) to tune into a lower frequency.
AUTO
AFM 88.9MHz
No colon (:)
English
53 En
FM/AM tuning
y
• When this unit is tuned into a station, the TUNED indicator
lights up.
• Hold down the button to continue searching when this unit is in
the manual tuning mode.
• Press GINFO (or AINFO) repeatedly to toggle the frequency
information and sound field program information in the front
panel.
Before performing the following operations, press 4TUNER
on the remote control.
Using station preset feature
Use this feature to store up to 40 stations FM/AM stations
(A1 to E8: 8 preset station numbers in each of the 5 preset
station groups). Preset the desired stations to this unit by
using the automatic or manual preset tuning features in
advance (see “Automatic station preset” and “Manual
station preset” on page 55).
Before performing the following operations, press 4TUNER
on the remote control.
■ Direct frequency tuning
Use this feature tune into the desired station directly by
entering the frequency.
1
2
Press 7BAND on the remote control
repeatedly to select the desired reception
band.
“FM” or “AM” appears in the front panel display.
Press BSEARCH MODE (or MSRCH
MODE) repeatedly to select “AUTO TUNING”
or “MANUAL TUNING”.
1
Press BSEARCH MODE (or MSRCH
MODE) repeatedly to select “PRESET
TUNING”.
2
Press EPRESET/TUNING/CH l / h (or
8PRESET/CH k / n) to select the desired
preset station number (A1 to E8).
The preset station group and number appear in the
front panel display along with the station band and
frequency.
A1:FM 88.9MHz
AFM 88.9MHz
Preset group and preset station number
No colon (:)
y
y
If a colon (:) appears in the front panel display, manual
tuning is not possible. Press BSEARCH MODE (or
MSRCH MODE) to turn the colon (:) off.
3
Enter the frequency of the desired station by
pressing the numeric buttons (G).
Example: To tune into 103.7 MHz
1
0
3
7
y
If the entered frequency is out of the range of the FM/AM tuning,
“WRONG STATION!” appears in the front panel display and
then this unit automatically tunes into the last selected station.
54 En
You can select the preset station group (A to E) by pressing
DA/B/C/D/E (or 8A-E/CAT. l / h) repeatedly.
FM/AM tuning
Before performing the following operations, press 4TUNER
on the remote control.
■ Automatic station preset
You can use the automatic preset tuning feature to store up
to 40 FM stations with strong signals (A1 to E8: 8 preset
station numbers in each of the 5 preset station groups) in
order.
1
2
Use this feature to store the AM or FM stations with weak
signals manually.
1
Tune into a station.
See page 53 for tuning instructions.
2
Press FMEMORY (or 9MEMORY).
The MEMORY indicator flashes in the front panel
display for approximately 30 seconds.
Rotate the RINPUT selector (or press
4TUNER) to select “TUNER” as the input
source.
Press CBAND (or 7BAND) to select “FM”
as the reception band.
“FM” appears in the front panel display.
Press and hold FMEMORY (or
9MEMORY) for more than 3 seconds.
The preset station number as well as the MEMORY
and AUTO indicators flashes. After approximately 5
seconds, automatic presetting starts from the current
frequency and proceeds toward higher frequencies.
MEMORY
Flashes
y
To cancel the preset memory mode, press FMEMORY (or
9MEMORY) again.
3
Flash
Press EPRESET/TUNING/CH l / h (or
8PRESET/CH k / n) repeatedly to select a
preset station group and number (A1 to E8)
while the MEMORY indicator is flashing.
• Press Eh (or 8k) to select a higher preset
station group and number.
• Press El (or 8n) to select a lower preset station
group and number.
BASIC
OPERATION
3
■ Manual station preset
Flashes
MEMORY
AUTO
A1:FM 88.9MHz
MEMORY
Flashes
A1:FM 88.9MHz
When automatic preset tuning is completed, the
MEMORY indicator disappears.
The displayed station has been stored as A1.
y
• You can specify the preset number from which this unit stores
FM stations. Press DA/B/C/D/E (or 8A-E/CAT. l / h) and
then EPRESET/TUNING/CH l / h
(or 8PRESET/CH k / n) repeatedly after you perform step 3
to select the preset station number under which the first station
will be stored.
• To cancel the automatic station preset, press FMEMORY (or
9MEMORY) again.
Notes
You can select the preset station group (A to E) by pressing
DA/B/C/D/E (or 8A-E/CAT. l / h) repeatedly.
4
Press FMEMORY (or 9MEMORY) while
the MEMORY indicator is flashing.
The station band and frequency appear in the front
panel display with the preset station group and
number you have selected. The MEMORY indicator
disappears from the front panel display.
Notes
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
55 En
English
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• If the number of received stations does not reach 40 (E8),
automatic preset tuning automatically stops after searching for
all the available stations and copy the stored stations to the rest
preset station numbers.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength or an AM radio station,
tune into it manually and store it as described in “Manual
station preset” below.
y
FM/AM tuning
■ Exchanging preset stations
You can exchange the assignments of two preset stations
with each other. The example below describes the
procedure to exchange preset station “E1” with “A5”.
Before performing the following operations, press 4TUNER
on the remote control.
1
Select preset station “E1” using DA/B/C/D/E
and EPRESET/TUNING/CH l / h.
See “Using station preset feature” on page 54.
2
Press and hold BEDIT for more than 3
seconds.
“E1” and the MEMORY indicator flash in the front
panel display.
Flashes
MEMORY
E1:FM 88.9MHz
Flashes
3
Select preset station “A5” using DA/B/C/D/E
and EPRESET/TUNING/CH l / h.
“A5” and the MEMORY indicator flash in the front
panel display.
See “Using station preset feature” on page 54.
Flashes
MEMORY
A5:FM 88.9MHz
Flashes
4
Press BEDIT again.
“EXCHANGE E1-A5” appears in the front panel
display and the assignments of the two preset stations
are exchanged.
56 En
XM SATELLITE RADIO TUNING
XM Satellite Radio tuning
XM Radio offers an extraordinary variety of commercial-free music, plus the best in premier sports, news, talk radio,
stand-up comedy, children’s and entertainment programming. XM is broadcast in superior digital audio quality from
coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan.
XM Satellite Radio online information
For U.S. customers: http://www.xmradio.com/
For Canadian customers: http://www.xmradio.ca/
Note
The XM Satellite Radio service is only available in the 48 contiguous United States (not available in Alaska and Hawaii) and Canada.
XM READY legal disclaimer
BASIC
OPERATION
XM monthly service subscription sold separately. XM Mini-Tuner and Home Dock required (each sold separately) to receive XM
service. It is prohibited to copy, decompile, disassemble, reverse engineer, hack, manipulate or otherwise make available any
technology or software incorporated in receivers compatible with the XM Satellite Radio System. Installation costs and other fees
and taxes, including a one-time activation fee may apply. All fees and programming subject to change. Channels with frequent
explicit language are indicated with an XL. Channel blocking is available for XM radio receivers by calling 1-800-XM-RADIO (US
residents) and 1-877-GET-XMSR (Canadian residents). For a full listing of the XM commercial- free channels and advertisingsupported channels, visit lineup.xmradio.com (US residents) or xmradio.ca (Canadian residents). Subscriptions subject to Customer
Agreement available at www.xmradio.com (US residents) and www.xmradio.ca (Canadian residents). Only available in the 48
contiguous United States and Canada. ©2008 XM Satellite Radio Inc. All rights reserved. All other trademarks are the property of
their respective owners.
■ Enjoying XM HD Surround content
This unit is equipped with the Neural Surround decoder that plays back the XM HD surround sound content of the XM
Satellite Radio broadcasts in multi-channels, resulting in a full surround sound experience (see page 78).
Connecting the XM Mini-Tuner Dock
Connect the XM Mini-Tuner and the XM Dock (sold
separately) to the XM jack on the rear panel of this unit.
For details, see the operating instructions provided with
the XM Mini-Tuner Dock.
XM Mini-Tuner and XM Dock
(sold separately)
y
To ensure optimal reception of the XM Satellite Radio signals,
the XM Mini-Tuner Dock must be placed at or near a southerly
facing window with no obstacles in the path to the sky. You can
mount it indoors or outdoors. Use the “ANTENNA INFO”
information in the front panel or “XM Information” screen in the
video monitor (see page 61) to check the antenna reception level
and adjust the orientation of the antenna.
Note
If “CHECK ANTENNA” or “CHECK XM TUNER” appears in
the front panel display, the connection and setting of the antenna,
Home Dock, or XM Mini-Tuner may not correct (see page 114).
L
R
English
CD
SIRIUS
XM
ANTENNA
57 En
XM Satellite Radio tuning
Activating XM Satellite Radio
Once you have installed the XM Mini-Tuner Dock,
inserted the XM Mini-Tuner, connected the XM Dock to
your XM Ready® home audio system, and installed the
antenna, you are ready to subscribe and begin receiving
XM programming. There are three places to find your
eight character XM Radio ID: On the XM Mini-Tuner, on
the XM Mini-Tuner package, and on XM Channel 0.
Record the XM Radio ID in the following eight squares
for reference.
Basic XM Satellite Radio
operations
1
Rotate the RINPUT selector (or press
3XM) to select “XM” as the input source.
The cursor on the left of the XM indicator lights up in
the front panel display and the XM Satellite Radio
information (such as channel number, channel name,
category, artist name, or song title) for the currently
selected channel appears in the front panel display.
Lights up
MULTI CH
VCR
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
CD
TUNER
XM
SIRIUS
Note
001Preview
The XM Radio ID does not use the letters “I”, “O”, “S” or “F”.
Activate your XM Satellite Radio service in the U.S. online at
http://activate.xmradio.com/ or call 1-800-XM-RADIO (1-800967-2346). Activate your XM Satellite Radio service in Canada
online at https://activate.xmradio.ca/ or call 1-877-GET-XMSR
(1-877-438-9677). You will need a major credit card. XM will
send a signal from the satellites to activate the full channel lineup.
Activation normally takes 10 to 15 minutes, but during peak busy
periods you may need to keep your XM Ready home audio
system on for up to an hour. When you can access the full lineup
on your XM Ready home audio system you are done.
y
When you select “XM” as the input source, this unit
automatically recalls the previously selected channel.
Notes
• The XM Satellite Radio signals cannot be output at the
AUDIO OUT (REC) jacks.
• If a status message or an error message appears in the front
panel display or in the OSD, see the “XM Satellite Radio”
section in “Troubleshooting” on page 110 for appropriate
remedies.
2
Search for a channel by using one of the XM
Satellite Radio search modes.
• To select a channel from the all channel list, see
“All Channel Search mode” on page 59.
• To select a channel by category, see “Category
Search mode” on page 59.
• To select a channel from the preset channels, see
“Preset Search mode” on page 59.
• To select the desired channel directly by entering
the channel number, see “Direct number access
mode” on page 59.
y
• You can use the Neural Surround decoder to enjoy the XM HD
surround sound content of the XM Satellite Radio broadcasts in
multi-channels (see page 78).
• You can set the XM Satellite Radio preset channels (see
page 60).
• You can display the XM Satellite Radio information in the front
panel display or in the OSD (see page 61).
58 En
XM Satellite Radio tuning
Before performing the following operations, press 3XM.
■ All Channel Search mode
1
2
Press BSEARCH MODE (or MSRCH
MODE) repeatedly to select “ALL CH
SEARCH”.
Press EPRESET/TUNING/CH l / h (or
8PRESET/CH k / n) repeatedly to search
for a channel within all channels.
y
• You can search for a channel quickly by pressing and holding
EPRESET/TUNING/CH l / h (or 8PRESET/CH k / n).
• To display the XM Radio ID number displayed in the front
panel display, select channel “0”.
■ Category Search mode
2
3
Press BSEARCH MODE (or MSRCH
MODE) repeatedly to select “CAT SEARCH”.
Press DCATEGORY (or 8A-E/CAT. l / h)
repeatedly to change the channel category.
Press EPRESET/TUNING/CH l / h (or
8PRESET/CH k / n) repeatedly to search
for a channel within the selected channel
category.
y
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting the XM Satellite Radio preset
channels” on page 60.
y
The initial factory setting of all preset channels (A1 to E8) is “001
Preview”.
1
Press BSEARCH MODE (or MSRCH
MODE) repeatedly to select “PRESET
SEARCH”.
2
Press DCATEGORY (or 8A-E/CAT. l / h)
repeatedly to change the preset channel
group (A to E).
3
Press EPRESET/TUNING/CH l / h (or
8PRESET/CH k / n) repeatedly to change
the preset channel number (1 to 8).
y
You can also select the preset channel number directly by
pressing the numeric buttons (1 to 8) (G).
BASIC
OPERATION
1
■ Preset Search mode
■ Direct number access mode
1
Press MSRCH MODE on the remote control
repeatedly to select “ALL CH SEARCH” or
“CAT SEARCH”.
2
Press the numeric buttons (G) to enter the
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons (G) as shown below.
You can search for a channel quickly by pressing and holding
EPRESET/TUNING/CH l / h (or 8PRESET/CH k / n).
1
2
3
y
• To enter a one-digit or two-digit channel number, press the
numeric buttons (G) on the remote control and then press
TENT to confirm the input number.
• Instead of pressing TENT to tune into the channel
immediately, you can wait a few seconds until this unit confirms
the entered channel number.
• Pressing a button other than the numeric buttons (G) or TENT
cancels the Direct Number Access mode procedure.
English
59 En
XM Satellite Radio tuning
Before performing the following operations, press 3XM.
3
Setting the XM Satellite Radio
preset channels
You can use this feature to store up to 40 XM Satellite
Radio channels (A1 to E8: 8 preset channel numbers in
each of the 5 preset channel groups). You can then recall
any preset channel easily by selecting the preset channel
group and number as described in “Preset Search mode”
on page 59.
Press EPRESET/TUNING/CH l / h
(or 8PRESET/CH k / n) repeatedly to select
a preset channel group and number (A1 to
E8) while the MEMORY indicator is flashing.
The preset channel number appears in the front panel
display.
Flashes
MEMORY
C5 043XMU
Selected preset channel group and number
1
Search for a channel you want to set as a
preset channel by using one of the XM
Satellite Radio search modes.
See “Basic XM Satellite Radio operations” on
page 58 for details.
043XMU
Currently selected channel number
2
y
You can select the preset station group (A to E) by pressing
DA/B/C/D/E (or 8A-E/CAT. l / h) repeatedly.
4
Press FMEMORY (or 9MEMORY) to set
the selected XM Satellite Radio channel as a
preset channel while the MEMORY indicator
is flashing.
A colon (:) appears next to the preset channel number
for confirmation, and the MEMORY indicator turns
off in the front panel display.
Press FMEMORY (or 9MEMORY).
The MEMORY indicator flashes in the front panel
display for approximately 30 seconds.
C5:043XMU
Colon (:)
MEMORY
Flashes
Note
You must proceed to and carry out steps 3 through 4 while
the MEMORY indicator is flashing in the front panel
display.
60 En
Note
Once you set a new preset channel, the one previously stored in
the same preset channel group and number is cleared.
XM Satellite Radio tuning
Before performing the following operations, press 3XM.
y
■ Displaying the XM Satellite Radio
information in the front panel display
■ Displaying the XM Satellite Radio
information in the OSD
Press GINFO (or AINFO) repeatedly to toggle
between the following XM Satellite Radio
information display modes.
Press ODISPLAY.
The following screen is displayed in the OSD.
Displaying the XM Satellite Radio
information
You can display the XM Satellite Radio information (such
as channel number, channel name, category, artist name,
or song title) for the currently selected channel in the front
panel display or in the OSD.
Note
CHANNEL INFO
XMInformationANT:
[1]
Channel number/name
[2]
[3]
CATEGORY INFO
[4]
e.g.) 043 XMU
ALLCHSEARCH
043:XMU
:Rock
:Coldplay
:Speedofsound
BASIC
OPERATION
If a status message or an error message appears in the front panel
display or in the OSD, see the “XM Satellite Radio” section in
“Troubleshooting” on page 110 for appropriate remedies.
• The front panel display can indicate up to 14 alphanumeric
characters at once. You can set whether to display the XM
Satellite Radio information in the front panel display in a
continuous manner or by 14 alphanumeric characters at once by
using the “FL SCROLL” parameter in “OPTION MENU” (see
page 96).
• If the XM Satellite Radio information contains a character that
cannot be recognized by this unit, the character will be
displayed with a space.
• To hold the current XM Raido information, press 8ENTER on
the remote control while it is being displayed. The HOLD
indicator flashes in the front panel display while you are
holding the XM information. Press 8ENTER again to release
the held information.
• When the antenna of the XM Mini-Tuner Dock cannot receive
the signals, “NO SIGNAL” appears in the front panel display.
[5]
[6]
e.g.) ROCK
Channel category
[1] Search mode (see page 58)
SONG INFO
e.g.) Coldplay / Sp
Artist name / Song title
[2] Channel category
[3] Song title
[4] Antenna reception level
ANTENNA INFO
e.g.) 043
ANT:
Channel number/Antenna reception level
-
[5] Channel number/name
[6] Artist name
y
DSP PROG. INFO
e.g.) 7ch Enhancer
Sound field program
Back to “CHANNEL INFO”
61 En
English
• To turn off the OSD, press ODISPLAY again.
• XM status messages also appear in the OSD.
• You can select the amount of time the XM Satellite Radio
information is displayed in the OSD by using the “OSDSOURCE” parameter in “OPTION MENU” (see page 96).
• To hold the XM Satellite Radio information, press 8ENTER
on the remote control while it is being displayed in the OSD.
“HOLD” appears in the screen while you are holding the XM
information. Press 8ENTER again or change the XM Satellite
Radio channel to release the held information.
• The current XM Satellite Radio reception level appears on the
top of the XM Satellite Radio information screen. For the best
reception, adjust the orientation of the antenna of Home Dock
so that “
” or “
” is displayed here. “
” is displayed if
the antenna cannot receive the signals correctly. In this case,
adjust the orientation of the antenna (see page 57).
SIRIUS SATELLITE RADIO™ TUNING
SIRIUS Satellite Radio™ tuning
SIRIUS Satellite Radio provides over 130 channels of exclusive entertainment and 100% commercial-free music. Only
SIRIUS has more than 65 original music channels, from today’s hits to R&B, oldies, and classical masterpieces. From
authentic country and real bluegrass to cool jazz, hot latin, reggae, rock and many more. Best of all, it's all 100%
commercial-free.
SIRIUS also has more than 55 channels of world-class sports, news and entertainment. Included as part of your
subscription, you get up to 16 NFL games a week, up to 40 NBA games a week and up to 40 NHL games a week. (Games
are broadcast during their respective seasons.)
Coupled with great sports news from ESPN, the SIRIUS sports offering is unrivaled. And don't forget a host of other
great news and entertainment, like NPR, CNBC, Fox News, Radio Disney and E! Entertainment Radio. For more
information, visit http://www.sirius.com/.
SIRIUS Satellite Radio legal disclaimer
SIRIUS is available in the U.S.A. for subscribers with addresses in the continental U.S.A. and is available in Canada for subscribers
with a Canadian address. To Get SIRIUS Satellite Radio a subscription and compatible tuner and antenna are required and sold
separately. Visit sirius.com for the most complete and up-to-date channel lineup and information.
“SIRIUS” and the SIRIUS dog logo and related marks are trademarks of SIRIUS Satellite Radio Inc.
Connecting the SiriusConnect™
tuner
Connect the SiriusConnect tuner (sold separately) to the
SIRIUS jack on the rear panel of this unit. For details, see
the operating instructions provided with the SiriusConnect
tuner.
SiriusConnect™ tuner and the antenna
(sold separately)
y
• To ensure optimal reception of the SIRIUS Satellite Radio
signals, the antenna of the SiriusConnect tuner must be placed
at or near a window with no obstacles in the path to the sky. The
orientation of the antenna for the best reception differs
depending on the area. Refer to the instruction manuals
supplied with the SiriusConnect tuner for the installation of the
antenna.You can mount it indoors or outdoors.
• Use the “ANTENNA INFO” information in the front panel or
“SIRIUS Information” screen in the video monitor (see
page 67) to check the antenna reception level and adjust the
orientation of the antenna.
• You need to connect the SiriusConnect tuner to the AC wall
outlet.
Notes
L
T
AN
R
DC
5V
CD
SIRIUS
XM
ANTENNA
AM
62 En
To the AC wall outlet
• If “CHECK SR TUNER” or “ANTENNA ERROR” appears in
the front panel display, the connection of the SiriusConnect
tuner or antenna is incorrect. In such cases, check the
connection of the SiriusConnect tuner and the antenna (see
page 115).
• If “NOT SUPPORTED” appears in the front panel display, this
unit does not support the connected SiriusConnect tuner.
SIRIUS Satellite Radio™ tuning
Activating SIRIUS Satellite
Radio™ subscription
Before using the SIRIUS Satellite Radio feature, you need
to activate your SIRIUS Satellite Radio subscription. To
activate the subscription you need the Sirius ID which is
uniquely assigned to the SiriusConnect tuner. Sirius ID is
12-digit number and it appears on the package of the
SiriusConnect tuner, on the label of the SiriusConnect
tuner, and when you tune into the SIRIUS Satellite Radio
channel “0” (see below).
Basic SIRIUS Satellite Radio™
operations
Before performing the following operations, set the operation
mode selector on the remote control to FSOURCE.
1
■ Displaying the Sirius ID of your
SiriusConnect tuner
1
Press KSIRIUS on the remote control.
2
Press G0 and then TENT to display the
Sirius ID of your SiriusConnect tuner.
“000 Sirius IDxxxxxxxxxxxx” (“xxxxxxxxxxxx”
indicates the 12-digit Sirius ID of your SiriusConnect
tuner) appears in the front panel display.
Rotate the RINPUT selector (or press
KSIRIUS) to select “SIRIUS” as the input
source.
The cursor on the left of the SIRIUS indicator lights
up in the front panel display and the SIRIUS Satellite
Radio information (such as channel number, channel
name, category, artist name, or song title) for the
currently selected channel appears in the front panel
display.
Lights up
V-AUX
DTV/CBL
DVD
MD/CD-R
CD
TUNER
XM
SIRIUS
y
When you select “SIRIUS” as the input source, this unit
automatically recalls the previously selected channel.
To scroll the message again, press GINFO (or AINFO).
Notes
Write the Sirius ID below.
• The SIRIUS Satellite Radio signals cannot be output at the
AUDIO OUT (REC) jacks.
• When you have not activated your subscription yet, you
can only select “184” or “000”.
• If a status message or an error message appears in the front
panel display or in the OSD, see the “SIRIUS Satellite
Radio” section in “Troubleshooting” on page 115 for
appropriate remedies.
ID:
Contact SIRIUS Satellite Radio to activate
your subscription.
SIRIUS Satellite Radio online information
Contact for activation
URL: https//activate.siriusradio.com/
Phone: 1-888-539-SIRIUS (1-888-539-7474)
DVR
184 SIRIUS Wea
y
3
VCR
BASIC
OPERATION
MULTI CH
2
y
Status messages appear in the front panel display or video
monitor during the activation. Once the activation is finished,
“SUB UPDATED” appears. For details, see “SIRIUS Satellite
Radio” section on page 115.
Search for a channel by using one of the
SIRIUS Satellite Radio search modes.
• To select a channel from the all channel list, see
“All Channel Search mode” on page 64.
• To select a channel by category, see “Category
Search mode” on page 64.
• To select a channel from the preset channels, see
“Preset Search mode” on page 64.
• To select the desired channel directly by entering
the channel number, see “Direct number access
mode” on page 64.
y
63 En
English
• If you tune into a channel that you do not subscribe, “CALL
888-539-SIRIUS TO SUBSCRIBE” appears in the front panel
display. To scroll the message again, press GINFO (or
AINFO).
• You can set the SIRIUS Satellite Radio preset channels (see
page 65).
• You can display the SIRIUS Satellite Radio information in the
front panel display or in the video monitor (see page 67).
SIRIUS Satellite Radio™ tuning
Before performing the following operations, press KSIRIUS
on the remote control.
■ All Channel Search mode
1
Press BSEARCH MODE (or MSRCH
MODE) repeatedly to select “ALL CH
SEARCH”.
2
■ Preset Search mode
Prior to selecting a preset channel in the Preset Search
mode, you must preset SIRIUS channels. For details, see
“Setting the SIRIUS Satellite Radio™ preset channels” on
page 65.
1
Press B SEARCH MODE (or MSRCH
MODE) repeatedly to select “PRESET
SEARCH”.
Press EPRESET/TUNING/CH l / h (or
8PRESET/CH k / n) repeatedly to search
for a channel within all channels.
2
Press DCATEGORY (or 8A-E/CAT. l / h)
repeatedly to change the preset channel
group (A to E).
• You can search for a channel quickly by pressing and holding
EPRESET/TUNING/CH l / h (or 8PRESET/CH k / n).
• You can skip channels to the previous or next category by
pressing DCATEGORY (or 8A-E/CAT. l / h).
3
Press EPRESET/TUNING/CH l / h (or
8PRESET/CH k / n) repeatedly to change
the preset channel number (1 to 8).
y
y
■ Category Search mode
1
Press BSEARCH MODE (or MSRCH
MODE) repeatedly to select “CAT SEARCH”.
2
Press DCATEGORY (or 8A-E/CAT. l / h)
repeatedly to change the channel category.
3
Press EPRESET/TUNING/CH l / h (or
8PRESET/CH k / n) repeatedly to search
for a channel within the selected channel
category.
You can also select the preset channel number directly by
pressing the numeric buttons (1 to 8) (G).
■ Direct number access mode
1
Press MSRCH MODE on the remote control
repeatedly to select “ALL CH SEARCH” or
“CAT SEARCH”.
2
Press the numeric buttons (G) to enter the
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons (G) as shown below.
y
You can search for a channel quickly by pressing and holding
EPRESET/TUNING/CH l / h on the front panel (or
8PRESET/CH k / n on the remote control).
1
2
3
Note
This unit skips the channels when this unit is All Channel Search
mode or Category Search mode in the following cases (it is not
malfunction of this unit):
– the channel is locked (see page 65).
– the channel is out of service.
– you do not subscribe to the channel.
64 En
y
• To display the Sirius ID number displayed in the front panel
display, select channel “0”.
• To enter a one-digit or two-digit channel number, press the
numeric buttons (G) on the remote control and then press
TENT to confirm the input number.
• Instead of pressing TENT to tune into the channel
immediately, you can wait a few seconds until this unit confirms
the entered channel number.
• If no button is pressed within a few seconds after you enter a
one-digit or two-digit number, this unit automatically confirms
the entered channel number.
• If the selected channel is locked, “PIN:___” appears in the front
panel display. Enter the four-digit Parental Lock code number
by using the numeric buttons (G) or press TENT to cancel
(see page 65).
SIRIUS Satellite Radio™ tuning
y
Before performing the following operations, press KSIRIUS
on the remote control.
Setting the SIRIUS Satellite
Radio™ preset channels
You can select the preset station group (A to E) by pressing
DA/B/C/D/E (or 8A-E/CAT. l / h) repeatedly.
4
You can use this feature to store up to 40 SIRIUS Satellite
Radio channels (A1 to E8: 8 preset channel numbers in
each of the 5 preset channel groups). You can then recall
any preset channel easily by selecting the preset channel
group and number as described in “Preset Search mode”
on page 64.
1
A1:023 Hair Na
Currently selected channel number
Press FMEMORY (or 9MEMORY).
The MEMORY indicator flashes in the front panel
display for approximately 30 seconds.
Note
Once you set a new preset channel, the one previously stored in
the same preset channel group and number is cleared.
Setting the Parental Lock
You can use the Parental Lock feature to limit the access
to the desired SIRIUS Satellite channels. This unit
automatically skips the locked channels when this unit is
in the All Channel Search mode or Category Search mode
and you search a channel by pressing EPRESET/
TUNING/CH l / h (or 8PRESET/CH k / n).
MEMORY
■ Setting the code number and the locked
channels
Flashes
Use this feature to set the Parental Lock code number
(PIN) and select the channels to be locked.
Note
You must proceed to and carry out steps 3 through 4 while
the MEMORY indicator is flashing in the front panel
display.
3
Colon (:)
Press EPRESET/TUNING/CH l / h
(or 8PRESET/CH k / n) repeatedly to select
a preset channel group and number (A1 to
E8) while the MEMORY indicator is flashing.
The preset channel number appears in the front panel
display.
BASIC
OPERATION
Search for a channel you want to set as a
preset channel by using one of the SIRIUS
Satellite Radio search modes.
See “Basic SIRIUS Satellite Radio™ operations” on
page 63 for details.
001 SIRIUS Hit
2
Press FMEMORY (or 9MEMORY) to set
the selected SIRIUS Satellite Radio channel
as a preset channel while the MEMORY
indicator is flashing.
A colon (:) appears next to the preset channel number
for confirmation, and the MEMORY indicator turns
off in the front panel display.
1
Press 5AMP on the remote control and then
press MMENU to display.
2
Press 8n to select “MANUAL SETUP” and
then press 8ENTER.
3
Press 8n repeatedly to select “INPUT
MENU” and then press 8ENTER.
Flashes
MEMORY
A1023 Hair Na
English
Currently selected preset channel group and
number
65 En
SIRIUS Satellite Radio™ tuning
4
Note
Press 8k / n repeatedly to select “SIRIUS”
and then press 8ENTER.
The following menu screen appears.
A)
In the SIRIUS Satellite Radio channel list screen, this unit
outputs the sound of the selected channel even if the channel
is locked. Only the first eight characters of each channel
name are displayed in the list.
SIRIUS
. INPUTRENAME
VOL. TRIM;;;;;0.0dB
PARENTAL LOCK
10
5
p
[
[ ]/[ ]:Up/Down
[ENTER]:Enter
Press 8n repeatedly to select “PARENTAL
LOCK” and then press 8ENTER.
“NEW PIN:0000” appears.
Press 8ENTER to lock the selected
channel.
Check mark appears before the locked channel.
y
When you select the locked channel and press 8ENTER,
this unit unlocks the selected channel.
11
Repeat steps 9 and 10 to lock the channels
you want.
NEWPIN:0000
12
Press 9RETURN to exit from the
“PARENTAL LOCK” screen.
[0] [9]:NUMBER
[ENT]:Enter
13
Press MMENU to exit from the setup menu.
This unit is tuned into the last channel you select in
the “PARENTAL LOCK” screen. If the channel is
locked, this unit is tuned into “184 SIRIUS Weather
& Emergency” or “000 Sirius IDxxxxxxxxxxxx”
(“xxxxxxxxxxxx” indicates the Sirius ID of your
SiriusConnect tuner).
PARENTAL LOCK
Note
If a SiriusConnect tuner is not connected to this unit, “Not
Available” appears.
y
If the Parental Lock code number is already set, “PIN:___”
appears instead of “NEW PIN:0000”. Refer to step 8 and
then proceed the operations.
6
Enter the desired 4-digit code number by
using the numeric buttons (G).
y
Press 9RETURN to return the previous menu level
without setting the code number.
7
Press 8ENTER to confirm the code number.
“OK” and then the SIRIUS Satellite Radio channel
list appears. Refer to the step 9 and then proceed the
operations.
8
Enter the 4-digit code number you set at step
6 above to unlock the protection.
When the code number is correct, “OK” and then the
SIRIUS Satellite Radio channel list appears.
9
Press 8l / h repeatedly to select the
desired channel category and then press
8k / n repeatedly to select the channel you
want to lock.
66 En
y
• If you forget or want to change the Parental lock code number,
use “SR PIN” in “ADVANCED SETUP” to reset the Parental
Lock code number.
• When you select “ALL” in “INIT” (see page 109), all locked
channels are unlocked.
■ Tuning into the locked channels
You can tune into the locked channels by the Direct
number access mode or preset tuning mode. When you
tune into the locked channel, following message appears
in the front panel display. Enter the code number you set
for the Parental Lock feature by using the numeric buttons
(G) or press TENT to cancel the tuning.
PIN:____
Notes
• If the entered code number is incorrect, “Wrong” appears in the
front panel display and this unit is tuned into the previously
selected channel.
• If a channel is unlocked, you can also select the channel in
Zone2.
SIRIUS Satellite Radio™ tuning
Before performing the following operations, press KSIRIUS
on the remote control.
Displaying the SIRIUS Satellite
Radio™ information
You can display the SIRIUS Satellite Radio information
(such as channel number, channel name, category, artist
name, composer name, or song title) for the currently
selected channel in the front panel display or in the OSD.
Note
If a status message or an error message appears in the front panel
display or in the OSD, see the “SIRIUS Satellite Radio” section
in “Troubleshooting” on page 115 for appropriate remedies.
■ Displaying the SIRIUS Satellite Radio
information in the front panel display
y
• The front panel display can indicate up to 14 alphanumeric
characters at once. You can set whether to display the SIRIUS
Satellite Radio information in the front panel display in a
continuous manner or by 14 alphanumeric characters at once by
using the “FL SCROLL” parameter in “OPTION MENU” (see
page 96).
• If the SIRIUS Satellite Radio information contains a character
that cannot be recognized by this unit, the character will be
displayed with a space.
• To hold the current SIRIUS Satellite Radio information, press
8ENTER on the remote control while it is being displayed.
Press 8ENTER again to release the held information.
• When the antenna of the SiriusConnect tuner cannot receive the
signals, “ACQUIRING” appears in the front panel display.
• When an information is unavailable, “––––” appears.
■ Displaying the SIRIUS Satellite Radio
information in the OSD
Press GINFO (or AINFO) repeatedly to toggle
between the following SIRIUS Satellite Radio
information display modes.
[1]
CHANNEL INFO
e.g.) 008 Big '80s
[2]
Channel number/name
CATEGORY INFO
e.g.) Pop
Channel category
SIRIUSInformationANT:
[5]
ALLCHSEARCH
008:Big'80s
:Pop
:Sanumemo
[6]
[3]
:RoadtoIndia
[4]
C:FrankieZipper
BASIC
OPERATION
Press ODISPLAY on the remote control.
The following screen is displayed in the OSD.
[7]
[1] Search mode (see page 63)
[2] Channel category
SONG INFO
e.g.) Sanumemo / Roa
Artist name / Song title
[3] Song title
[4] Composer name
[5] Antenna reception level
COMPOSER INFO
e.g.) Frankie Zipper
[6] Channel number/name
[7] Artist name
Composer name
y
ANTENNA INFO
e.g.) 043
ANT:
Channel number/Antenna reception level
DSP PROG. INFO
e.g.) 7ch Enhancer
Sound field program
• To turn off the OSD, press ODISPLAY again.
• SIRIUS status messages also appear in the OSD.
• You can select the amount of time the SIRIUS Satellite Radio
information is displayed in the OSD by using the “OSDSOURCE” parameter in “OPTION MENU” (see page 96).
• To hold the SIRIUS Satellite Radio information, press
8ENTER on the remote control while it is being displayed in
the OSD. While this unit is holding the information screen,
“HOLD” appears in the OSD.
• The HOLD indicator flashes in the front panel display while
you are holding the SIRIUS information. Press 8ENTER
again or change the SIRIUS Satellite Radio channel to release
the held information.
67 En
English
Back to “CHANNEL INFO”
-
USING IPOD™
Using iPod™
Once you have stationed your iPod in a Yamaha iPod universal dock (such as YDS-10, sold separately) connected to the
DOCK terminal of this unit (see page 25), you can enjoy playback of your iPod using the supplied remote control. You
can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the compression artifacts
(such as the MP3 format) stored on your iPod (see page 50).
Notes
• Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.
• Some features may not be compatible depending on the model or the software version of your iPod.
y
• For a complete list of status messages that appear in the front panel display and in the OSD, see the “iPod” section in
“Troubleshooting” on page 116.
• Once the connection between your iPod and this unit is complete, “iPod connected” appears in the front panel display and the DOCK
indicator lights up in the front panel display.
• Only the analog audio and video signals of your iPod are input at the DOCK terminal, and the analog audio signals can be output at the
analog AUDIO OUT (REC) jacks for recording.
• Your iPod battery is automatically charged when your iPod is stationed in a Yamaha iPod universal dock connected to the DOCK
terminal of this unit as long as this unit is turned on. You can also select whether this unit charges the battery of the stationed iPod or
not when this unit is in the standby mode by selecting the “STANDBY CHARGE” parameter in “INPUT MENU” (see page 94). The
DOCK indicator turns on while this unit charges the battery of the connected iPod when this unit is in the standby mode.
Controlling iPod™
You can control your iPod when “V-AUX” is selected as the input source. The operations of your iPod can be done with
the aid of the OSD of this unit (menu browse mode) or without it (simple remote mode).
■ Remote control operation
Before performing the following operations, press
4V-AUX/DOCK on the remote control.
Button
8 ENTER
Function
Subsequent menu
k
Menu up
n
Menu down
l
Previous menu
h
Subsequent menu
0 ll
Search backward (Press and hold)
hh
Search forward (Press and hold)
a
Skip forward
b
Skip backward
s
Stop
e
Pause (Menu browse mode)
Play/Pause (Simple remote mode)
p
Play (Menu browse mode)
Play/Pause (Simple remote mode)
M MENU
Previous menu
O DISPLAY
Display
68 En
■ Controlling iPod in the simple remote
mode
You can perform the basic operations of your iPod (play,
stop, skip, etc.) using the supplied remote control without
the aid of the OSD of this unit.
y
• You can view the photos or video clips stored on your iPod
(some models only).
• Operations can be also done with the controls on your iPod.
Using iPod™
■ Controlling iPod in the menu browse
mode
You can perform the advanced operations of your iPod
using the supplied remote control with the aid of the OSD
of this unit. You can browse the songs stored on your iPod
in the OSD. Further, you can change or adjust settings for
your iPod to suit your personal preferences.
y
• The name of the song being played also appears in the front
panel display according to the “FL SCROLL” parameter in
“OPTION MENU” (see page 96).
• You can select the amount of time the iPod menu and play
information is displayed in the OSD by using the “OSDSOURCE” in “OPTION MENU” (see page 96).
Notes
1
Press ODISPLAY on the remote control.
The following display appears in the OSD.
y
When “Shuffle” is set to a setting other than “Off”, “
” appears
in the top right corner while songs or albums are being shuffled.
Repeat Repeat
Use this feature to set this unit to repeat one song or a
sequence of songs.
Choices: Off, One, All
• Select “Off” to deactivate this feature.
• Select “One” to set this unit to repeat one song.
• Select “All” to set this unit to repeat a sequence of
songs.
y
When “Repeat” is set to a setting other than “Off”, “ ” or “ ”
appears in the top right corner while one song or a sequence of
songs are being repeated.
1
■ The function of the play information
display
[1]
iPod
Top
iPod[Play]
1/9
FrankieZipper
Made-to-order
RoadtoIndia
||;;;;;;;;;;;;;;;;;;
0:51-7:44
All
Playlists
Artists
Albums
Songs
Genres
Composers
Settings
>
>
>
>
>
>
>
[2]
[3]
[4]
[5]
2
Press 8k / n / l / h to navigate the iPod
menu and then press 8ENTER to begin
playback of the selected song.
Choices: Playlists (playlists), Artists (artists), Albums
(albums), Songs (songs), Genres (genres),
Composers (composers), Settings (settings)
• Playlists > Songs
• Artists > Albums > Songs
• Albums > Songs
• Songs
• Genres > Artists > Albums > Songs
• Composers > Albums > Songs
• Settings > Shuffle, Repeat
All
BASIC
OPERATION
• Operations cannot be done with the controls on your iPod.
• There are some characters that cannot be displayed in the front
panel display or in the OSD of this unit. Those characters are
replaced with underscores “_”.
• The “Settings” parameters can be changed or adjusted only in
the OSD. Press 8ENTER or 8k/n repeatedly on the remote
control to toggle between the “Settings” parameter settings.
• You cannot browse the photos or video clips stored on your
iPod in the OSD. Use the simple remote mode to enjoy
watching the photos or video clips stored on your iPod.
Shuffle Shuffle
Use this feature to set this unit to play songs or albums in
random order.
Choices: Off, Songs, Albums
• Select “Off” to deactivate this feature.
• Select “Songs” to set this unit to play songs in random
order.
• Select “Albums” to set this unit to play albums in
random order.
[6]
[1]
Playback status
[2]
Track number/total tracks
[3]
Artist name
[4]
Song title
[5]
Progress bar
[6]
Elapsed time
[7]
Shuffle and repeat icons
[8]
(playback),
forward) and
[9]
Name of the album
[7]
[8]
[9]
[10]
(pausing),
(search
(search backward)
English
[10] Remaining time
69 En
USING BLUETOOTH™ COMPONENTS
Using Bluetooth™ components
You can connect a Yamaha Bluetooth adapter (such as YBA-10, sold separately) to the DOCK terminal of this unit and
enjoy the music contents stored in your Bluetooth component (such as a portable music player) without wiring between
this unit and the Bluetooth component. You need to perform “pairing” the connected Bluetooth adapter and your
Bluetooth component in advance.
Pairing the Bluetooth™ adapter
and your Bluetooth™ component
Pairing must be performed when using a Bluetooth
component with the Bluetooth adapter connected to this
unit for the first time or if the pairing data has been
deleted. “Pairing” refers to the operation of registering a
Bluetooth component for Bluetooth communications.
Note
If the Bluetooth adapter is not connected to the DOCK
terminal of this unit, “No BT adapter” appears in the front
panel display.
4
Check that the Bluetooth component detects
the Bluetooth adapter.
If the Bluetooth component detects the Bluetooth
adapter, “YBA-10 YAMAHA” (example) appears in
the Bluetooth device list.
5
Select the Bluetooth adapter in the Bluetooth
device list and then enter the pass key
“0000” on the Bluetooth component.
When the pairing procedure is successful,
“Completed” appears in the front panel display.
y
• You only need the pairing operation for the first time that you
use the Bluetooth component with the Bluetooth adapter.
• Pairing requires operations on this unit and on the other
component with which Bluetooth communications are to be
established. If necessary, refer to the other component’s
operating instructions.
There are two pairing methods: pairing by using “START
PAIRING” in “SET MENU” and quick pairing.
■ Pairing by using “SET MENU”
Use this feature to perform pairing with the video monitor.
Select “START PAIRING” in “INPUT MENU”. See
page 95 for details.
■ Quick pairing
To ensure security, a time limit of 8 minutes is set for the
pairing operation. You are recommended to read and fully
understand all the instructions before starting.
1
Rotate the RINPUT selector (or press
4V-AUX/DOCK) to select “V-AUX” as the
input source.
2
Turn on the Bluetooth component you want
to pair with.
3
Press and hold CBAND (or 7BAND) for 3
seconds.
Once the Bluetooth adapter starts pairing,
“Searching...” appears for a moment. While the
Bluetooth adapter is in the pairing mode, DOCK
indicator flashes in the front panel display.
y
To cancel the pairing, press CBAND (or 7BAND) again.
70 En
Note
The Yamaha Bluetooth adapter can be paired with up to eight
Bluetooth components. When pairing is conducted successfully
with a ninth component and the pairing data is registered, the
pairing data for the least recently used other component is
cleared.
Playback of the Bluetooth™
component
1
Rotate the RINPUT selector (or press
4V-AUX/DOCK) to select “V-AUX” as the
input source.
2
Start playback of your Bluetooth component.
When the connected Bluetooth adapter detects the
Bluetooth component, “BT connected” and the
DOCK indicator appears in the front panel display.
y
• When you press 8ENTER on the remote control, the
connected Bluetooth adapter searches and connect to the last
connected Bluetooth component. If the Bluetooth adapter
cannot find the Bluetooth component, “Not found” appears in
the front panel display.
• To disconnect the Bluetooth adapter from the Bluetooth
component, press 9RETURN.
RECORDING
Recording
Recording adjustments and other operations are performed from the recording components. Refer to the operating
instructions for those components.
Caution
The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in noise being
recorded. Therefore, if you want to use this unit to record sources encoded in DTS, the following considerations and
adjustments need to be made. To play DTS-encoded DVDs and CDs (when using a digital audio connection) on your
DTS-compatible player, follow its operating instructions to make a setting so that the analog signal will be output
from the player.
Notes
BASIC
OPERATION
• When this unit is set to the standby mode, you cannot record between other components connected to this unit.
• TONE CONTROL (see page 52) and VOLUME settings, the speaker level (see page 52) and the sound field programs (see page 48)
do not affect recorded material.
• The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded.
• The XM Satellite Radio and SIRIUS Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks.
• Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording.
• A given input source is not output on the same AUDIO OUT (REC) channel.
• S-video and composite video signals pass independently through the video circuits of this unit. Therefore, when recording or dubbing
video signals input from a video source component that provides only an S-video or a composite video signal, you can only record an
S-video or a composite video signal on your VCR.
• The analog audio signals input at the DOCK terminal can be output at the analog AUDIO OUT (REC) jacks for recording.
• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright
laws.
y
Do a test recording before you start an actual recording.
If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture
itself may be disturbed due to those signals.
1
Turn on all the connected components.
2
Rotate the RINPUT selector (or press one
of the input selector buttons (4)) to select
the source component you want to record
from.
3
Start playback on the selected source
component or select a broadcast station.
4
Start recording on the recording component.
English
71 En
ADVANCED SOUND CONFIGURATIONS
Advanced sound configurations
Changing sound field parameter
settings
You can enjoy good quality sound with the initial factory
settings. Although you do not have to change the initial
factory settings, you can change some of the parameters to
better suit the input source or your listening room.
3
Press BPROG l / h repeatedly to select
the desired sound field program you want to
adjust.
4
Press 8k / n to select the desired sound
field parameter and then 8l / h to change
the selected sound field parameter value.
• Press 8h to increase the value.
• Press 8l to decrease the value.
Note
You cannot change the sound field parameter values when
“MEMORY GUARD” in “OPTION MENU” is set to “ON” (see
page 97). If you want to change the sound field parameter values,
set “MEMORY GUARD” to “OFF”.
1
Turn on the video monitor connected to this
unit.
2
Press 5AMP and then SPARAMETER on
the remote control.
The following screen is shown in the OSD.
Sound field program category
MOVIE
Cursor
.
1/2
y
• For details about the function and control range of each sound
field parameter, see page 74.
• When you set a sound field parameter to a value other than the
initial factory settings, an asterisk mark (*) appears by the
sound field parameter name in the OSD.
• Repeat steps 3 and 4 as necessary to change other sound field
program parameter settings.
• The available sound field parameters for some of the sound field
programs may be displayed on more than one page in the OSD.
In this case, press 8k / n to scroll through pages.
• To initialize the parameters of the selected sound field program,
press 8n repeatedly to select “INITIALIZE” and then press
8h. Once the confirmation screen appears in the OSD, press
8h to confirm or 8l to cancel the initialization.
Sci-Fi
SUR.;;PLIIx Movie
DSP LEVEL;;;;;0dB
P.INIT.DLY;;;16ms
P.ROOM SIZE;;;1.0
S.INIT.DLY;;;16ms
S.ROOM SIZE;;;1.0
MOVIE
[p]/[[]: Select
Sound field parameters Sound field parameter
values
[[]: Initialize
5
72 En
2/2
Sci-Fi
SB INIT.DLY;;15ms
SB ROOM SIZE ;;1.0
DIALOG LIFT;;;;;0
. INITIALIZE
Press SPARAMETER to turn off the sound
field parameter screen.
Advanced sound configurations
■ Basic configuration of sound field
programs
Each sound field program has some parameters defining
the characteristics of the program. To customize the
selected sound field program, adjust “DSP LEVEL” and/
or “DIALG.LIFT” first, and then try other parameters.
Adjusting the vertical dialogue position
(DIALG.LIFT)
Use this feature to adjust the vertical position of the
dialogues in movies. The ideal position of the dialogues is
at the center of the video monitor screen.
y
To change sound field parameter settings, see page 72 for details.
Adjusting the effect sound level of the sound
field programs (DSP LEVEL)
Sound field programs add effect sounds (DSP effect
sounds) to the original source sound to create sound field
in the listening room. Use the “DSP LEVEL” parameter to
adjust the level of the effect sounds.
The DSP effect
sound level is low.
The DSP effect sound
level is high.
Increase the value of “DSP LEVEL”
• The effect sound of the selected sound field
program is too weak.
• You cannot recognize any difference between the
sound field programs.
If the dialogues are heard at the lower position of the video
monitor screen, increase the value of “DIALG.LIFT”.
Move up to the ideal dialogue position.
Choices: 0, 1, 2, 3, 4, 5
“0” (initial setting) is the lowest position, and “5” is the
highest position.
Notes
ADVANCED
OPERATION
Adjust “DSP LEVEL” in the following cases:
The ideal
dialogue
position.
• “DIALG.LIFT” is only available only “EXTRA SP ASSIGN”
is set to “PRESENCE” (see page 72).
• You cannot move the dialogue position down from the initial
dialogue position.
Decrease the value of “DSP LEVEL”
• The sound is vague.
• You feel that the additional sound effect is
excessive.
Control range: –6 dB to +3 dB
English
73 En
Advanced sound configurations
■ Sound field parameters for the advanced configurations
Use the following sound field parameters to customize sound field programs in detail.
y
To change sound field parameter settings, see page 72 for details.
Sound field parameter
INIT.DLY
P.INIT.DLY
S.INIT.DLY
SB INI.DLY
Features
Initial delay. Presence, surround, and surround back sound field initial delay. Changes the
apparent distance from the source sound by adjusting the delay between the direct sound and the
first reflection heard by the listener. The smaller the value, the closer the sound source seems to
the reflection face.
y
When you adjust the initial delay parameters, we also recommend that you adjust the
corresponding room size parameters likewise. This adjustment is especially effective for the
CINEMA DSP programs.
Control range: 1 to 99 ms (INIT.DLY and P.INIT.DLY)
1 to 49 ms (S.INIT.DLY and SB INI.DLY)
Source sound
Level
Level
Level
Early
reflections
Time
Time
Time
Delay
Delay
Delay
Sound source
Reflection face
Small value = 1 ms
74 En
Large value = 99 ms
Advanced sound configurations
Sound field parameter
ROOM SIZE
P.ROOM SIZE
S.ROOM SIZE
SB ROOM SIZE
Features
Room size. Presence, surround, and surround back room size. Adjusts the apparent size of the
surround sound field. The larger the value, the larger the surround sound field becomes. As the
sound is repeatedly reflected around a room, the larger the hall is, the longer the time between
the original reflected sound and the subsequent reflections. By controlling the time between the
reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter
from one to two doubles the apparent length of the room.
y
When you adjust the room size parameters, we also recommend that you adjust the
corresponding initial delay parameters likewise. This adjustment is especially effective for the
CINEMA DSP programs.
Control range: 0.1 to 2.0
Time
Early
reflections
Level
Level
Level
Source sound
Time
Time
Sound source
Small value = 0.1
Liveness. Surround and surround back sound field liveness. Adjusts the reflectivity of the virtual
walls in the hall by changing the rate at which the early reflections decay. The early reflections of
a sound source decay much faster in a room with acoustically absorbent wall surfaces than in one
which has highly reflective surfaces. A room with acoustically absorbent surfaces is referred to
as “dead”, while a room with highly reflective surfaces is referred to as “live”. This parameter
lets you adjust the early reflection decay rate and thus the “liveness” of the room.
ADVANCED
OPERATION
Control range: 0 to 10
Source sound
Time
Small reflected
sound
Small value = 0
Level
Dead
Level
Live
Level
LIVENESS
S.LIVENESS
SB LIVENESS
Large value = 2.0
Time
Time
Large reflected
sound
Large value = 10
English
75 En
Advanced sound configurations
Sound field parameter
REV.TIME
Features
Reverberation time. Adjusts the amount of time taken for the dense, subsequent reverberation
sound to decay by 60 dB at 1 kHz. This changes the apparent size of the acoustic environment
over an extremely wide range. Set a longer reverberation time for “dead” sources and listening
room environments, and a shorter time for “live” sources and listening room environments.
Control range: 1.0 to 5.0 s
Source sound
Reverberation
Reverberation
Early reflections
60 dB
REV.TIME
Sound source
60 dB
60 dB
REV.TIME
REV.TIME
Short
reverberation
Long
reverberation
Small value = 1.0 s
REV.DELAY
Large value = 5.0 s
Reverberation delay. Adjusts the time difference between the beginning of the direct sound and
the beginning of the reverberation sound. The larger the value, the later the reverberation sound
begins. A later reverberation sound makes you feel as if you are in a larger acoustic environment.
Level
Control range: 0 to 250 ms
Source sound
(dB)
60 dB
Reverberation
Time
REV.DELAY
REV.LEVEL
REV.TIME
Reverberation level. Adjusts the volume of the reverberation sound. The larger the value, the
stronger the reverberation becomes.
Control range: 0 to 100%
Level
Source sound
(dB)
REV. LEVEL
Time
76 En
Advanced sound configurations
Sound field parameter
DIRECT
Features
2-channel stereo direct. Bypasses the decoders and the DSP processors of this unit for pure hi-fi
stereo sound when playing 2-channel analog sources.
(“2ch Stereo” only)
Choices: AUTO, OFF
y
• Select “AUTO” to bypass the decoders, the DSP processors and the tone control circuitry only
when “BASS” and “TREBLE” are set to 0 dB (see page 52).
• Select “OFF” not to bypass the decoders, the DSP processors and the tone control circuitry
when “BASS” and “TREBLE” are set to 0 dB.
• When multi-channel signals (Dolby Digital and DTS) are input, they are downmixed to 2
channels and output from the front left and right speakers.
• The low-frequency signals of the front left and right channels are redirected to the subwoofer
in the following cases:
– “LFE/BASS OUT” is set to “BOTH” (see page 85).
– “FRONT SP” is set to “SMALL” (see page 86) and “LFE/BASS OUT” is set to “SWFR”
(see page 85).
CT
SL
SR
SB
PL
PR
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
7-channel stereo center, surround left, surround right, surround back, presence left and presence
right levels. Adjusts the volume level of each channel in the 7-channel stereo mode. The
available parameters differ depending on the setting of the speakers.
Control range: 0 to 100%
(“7ch Stereo” only)
EFFECT LEVEL
(“Straight Enhancer” and
“7ch Enhancer” only)
Straight and 7-channel Compressed Music Enhancer effect level. The high-frequency signals of
some sources may be emphasized too much. In this case, set the effect level to “LOW”.
ADVANCED
OPERATION
Choices: HIGH, LOW
• Select “HIGH” for a high effect level.
• Select “LOW” for a low effect level.
■ Selecting decoders used with sound
field programs (SUR.)
Use this feature to select the desired decoder used with
MOVIE sound field programs (except “Mono Movie”).
See page 49 for details about MOVIE sound field
program.
Available decoders
Decoder
Functions
PLIIx Movie
PLII Movie
Dolby Pro Logic IIx (or Dolby Pro
Logic II) processing for movie
sources. The Pro Logic IIx decoder
is not available when “SUR.B L/R
SP” is set to “NONE” (see page 86).
Neo:6 Cinema
DTS processing for movie sources.
English
77 En
Advanced sound configurations
Selecting decoders
■ Selecting decoders for 2-channel
sources (surround decode mode)
Use this feature to play back sources with selected
decoders. You can play back 2-channel sources on multichannels.
y
You can change the decoder parameter settings (see page 79).
Press 5AMP and then SPARAMETER to display the decoder
parameters in the OSD. Press 8k / n repeatedly to select the
desired decoder parameter and then press 8l / h repeatedly to
change the value of the selected parameter.
Press 5AMP and then QSUR. DECODE
repeatedly on the remote control to select the
desired surround decoder.
You can select from the following modes depending on the
type of source you are playing and your personal
preference.
■ Decoder descriptions (SUR.)
Decoder
Descriptions
Pro Logic
Dolby Pro Logic processing for any sources.
PLIIx Movie
PLII Movie
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for movie sources. The Pro Logic IIx
decoder is not available when “SUR.B L/R SP” is set to “NONE” (see page 86).
PLIIx Music
PLII Music
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for music sources. The Pro Logic IIx
decoder is not available when “SUR.B L/R SP” is set to “NONE” (see page 86).
PLIIx Game
PLII Game
is not available when “SUR.B L/R SP” is set to “NONE” (see page 86).
Neo:6 Cinema
DTS processing for movie sources.
Neo:6 Music
DTS processing for music sources.
Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for game sources. The Pro Logic IIx decoder
Neural Surround processing for any sources.
Neural Sur.
(U.S.A. and Canada models
only)
The Neural Surround decoder is compatible with PCM signals and analog 2-channel input sources.
When Neural Surround-incompatible signals are being input while the Neural Surround decoder is
selected, multi-channel sources are decoded straight into the appropriate channels without any
additional effect processing and the Neural Surround-incompatible PCM signals are played back in
stereo. The Neural Surround decoder is especially suitable for the XM HD Surround program of XM
Satellite Radio.
y
When you select the surround decode mode for Dolby Digital, DTS or DTS 96/24 sources, this unit automatically selects “SURROUND
DECODE Dolby Digital”, “SURROUND DECODE DTS” or “SURROUND DECODE DTS 96/24” program.
78 En
Advanced sound configurations
Decoder parameter descriptions
Decoder parameter
PANORAMA
(“PLIIx Music” and “PLII
Music” only)
Features
Pro Logic IIx Music and Pro Logic II Music panorama. Sends stereo signals to the surround speakers as
well as the front speakers for a wraparound effect.
Choices: OFF, ON
DIMENSION
(“PLIIx Music” and “PLII
Music” only)
Pro Logic IIx Music and Pro Logic II Music dimension. Adjusts the sound field either towards the front
or towards the rear.
Control range: –3 (towards the rear) to +3 (towards the front)
Initial setting: STD (standard)
CENTER WIDTH
(“PLIIx Music” and “PLII
Music” only)
Pro Logic IIx Music and Pro Logic II Music center width. Moves the center channel output completely
towards the center speaker or towards the front left and right speakers. A larger value moves the center
channel output towards the front left and right speakers.
Control range: 0 (center channel sound is output only from the center speaker) to
7 (center channel sound is output only from the front left and right speakers)
Initial setting: 3
C. IMAGE
(“Neo:6 Music” only)
DTS Neo:6 Music center image. Adjusts the front left and right channel output relative to the center
channel to make the center channel more or less dominant as necessary.
Control range: 0.0 (center channel sound is output only from the front left and right speakers) to
1.0 (center channel sound output only from the center speaker)
Initial setting: 0.3
ADVANCED
OPERATION
English
79 En
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Customizing this unit (MANUAL SETUP)
You can use the following parameters in “SET MENU” to adjust a variety of system settings and customize the way this
unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
■ Auto setup
AUTO SETUP
Use this feature to automatically adjust speaker and system parameters (see page 32).
■ Manual setup
MANUAL SETUP
Use this feature to manually adjust speaker and system parameters.
Basic menu 1 BASIC MENU
Menu
A)SPEAKER SET
Parameter
Functions
Page
EXTRA SP ASSIGN
Selects the function of the speakers connected to the EXTRA SP
speaker terminal.
85
LFE/BASS OUT
Selects the speakers that output the LFE (low-frequency effect) and the
low-frequency signals.
85
FRONT SP
Selects the size of the front speakers.
86
CENTER SP
Selects the size of the center speaker.
86
SUR. L/R SP
Selects the size and number of the surround speakers.
86
SUR.B L/R SP
Selects the size and number of the surround back speakers.
86
CROSS OVER
Selects the crossover frequency of all the speakers set to “SML” (or
“SMALL”) in “SPEAKER SET” (see page 86).
87
SUBWOOFER PHASE
Switches the phase of your subwoofer if bass sounds are lacking or
unclear.
87
B)SP LEVEL
FR.L/FR.R/CNTR/
SUR.L/SUR.R/
SBL/SBR/SWFR/
PR.L/PR.R
Adjust the balance the speaker levels between the front left or
surround left speakers and each speaker selected in “SPEAKER SET”
(see page 85).
87
C)SP DISTANCE
UNIT
Selects the unit to adjust the speaker distance.
88
FRONT L/FRONT R/
CENTER/SUR. L/
SUR. R/SBL/SBR/
SWFR/PRNS L/
PRNS R
Adjust the distance of each speaker and the delay applied to the
respective channel.
88
Turns the test tone output on or off for the “SPEAKER SET”, “SP
LEVEL”, and “SP DISTANCE” settings.
88
D)TEST TONE
80 En
—
Customizing this unit (MANUAL SETUP)
Volume menu 2 VOLUME MENU
Parameter
Functions
Page
ADAPTIVE DRC
Selects whether this unit automatically adjusts the dynamic range in conjunction with the
volume level or not.
89
ADAPTIVE DSP LEVEL
Selects whether this unit adjusts the DSP effect level automatically in conjunction with the
volume level or not.
89
MUTE TYPE
Adjusts how much the mute function reduces the output volume (see page 45).
89
MAX VOL.
Sets the maximum volume level of the main zone.
89
INIT. VOL.
Sets the volume level of the main zone when the power of this unit is turned on.
89
Sound menu 3 SOUND MENU
Menu
A)EQUALIZER
Parameter
Functions
Page
Selects the type of equalizer.
90
GEQ
Adjusts the tonal quality of the speakers when you set “EQ TYPE
SELECT” to “GEQ”.
90
TEST
Selects whether this unit outputs the test tone while making
adjustments of “GEQ” or not.
90
SPEAKER
Adjusts the speaker LFE level.
91
HEADPHONE
Adjusts the headphone LFE level.
91
C)DYNAMIC
RANGE
SPEAKER
Adjusts the amount of the dynamic range compression of the speakers.
91
HEADPHONE
Adjusts the amount of the dynamic range compression of the
headphones.
91
D)LIPSYNC
HDMI AUTO
Selects whether this unit activates the automatic audio and video
synchronization function (automatic lip sync) or not.
92
AUTO
Makes fine adjustments of the audio delay when the automatic audio
and video synchronization function is active.
92
MANUAL
Adjustment the audio delay manually when the connected video
monitor is not compatible with the automatic audio and video
synchronization function or “HDMI AUTO” is set to “OFF”.
92
Use this feature to enjoy 6.1/7.1-channel playback for multi-channel
sources using the Dolby Pro Logic IIx, Dolby Digital EX, or DTS-ES
decoders by using the connected surround back speakers.
92
B)LFE LEVEL
E)EXTD SUR.
—
ADVANCED
OPERATION
EQ TYPE SELECT
English
81 En
Customizing this unit (MANUAL SETUP)
Input menu 4 INPUT MENU
Note
Some parameters described below may not be available for all input sources and some parameters are only available for specific input
sources.
Parameter
Functions
Page
I/O ASSIGNMENT
Assigns the input/output jacks according to the component to be used if the initial settings of
this unit do not correspond to your needs.
93
INPUT RENAME
Changes the name of the input source that appears in the OSD and in the front panel display.
94
VOL. TRIM
Adjusts the level of the signal input at each jack.
94
DECODER MODE
Switches the decoder activation mode. You can designate the reassigned digital input jacks for
DTS signals.
94
STANDBY CHARGE
Selects whether this unit charges the battery of the stationed iPod or not when this unit is in the
standby mode (see page 29).
94
PARENTAL LOCK
(U.S.A. and Canada
models only)
Sets the SIRIUS Parental Lock code number and the channel lock configuration (see page 65)
94
START PAIRING
Pair the connected Yamaha Bluetooth adapter (such as YBA-10, sold separately) with a
Bluetooth component (see page 70).
95
BGV
Selects the video source played back in the background of the sources input at the MULTI CH
INPUT jacks.
95
INPUT CH
Selects the number of channels input from an external decoder.
95
FRONT
Selects the analog jacks at which the front channel signals from an external decoder are input
when you set “INPUT CH” to “8CH”.
95
Option menu 5 OPTION MENU
Menu
A)DISPLAY SET
B)VIDEO SET
C)MEMORY GUARD
82 En
Parameter
Functions
Page
DIMMER
Adjusts the brightness of the front panel display.
96
OSD SHIFT
Adjusts the vertical position of the OSD.
96
OSD-SOURCE
Sets the amount of time to display the SIRIUS Satellite Radio
information, XM Satellite Radio information, or iPod menu in the
video monitor after you perform a certain operation.
96
OSD-AMP
Sets the amount of time to display the status information screen after
you perform a certain operation.
96
FL SCROLL
Selects the mode to display the SIRIUS Satellite Radio information,
XM Satellite Radio information, or iPod menu in the front panel
display.
96
VIDEO CONV.
Selects whether to convert the video signals input at the VIDEO,
S VIDEO, and COMPONENT VIDEO jacks.
97
Prevents accidental changes to sound field program parameter values
and other system settings.
97
—
Customizing this unit (MANUAL SETUP)
Menu
Functions
Page
AUDIO SELECT
Designates the default audio input jack select setting for the input
sources connected to the DIGITAL INPUT jacks when you turn on the
power of this unit.
98
DECODER MODE
Designates the default decoder mode for the input sources connected
to the DIGITAL INPUT jacks when you turn on the power of this unit.
98
EXTD SUR.
Designates the extended decoder mode for the input sources connected
to the DIGITAL INPUT jacks when you turn on the power of this unit.
98
E)HDMI SET
S.AUDIO
Selects whether to play back HDMI audio signals on this unit or on
another HDMI component connected to the HDMI OUT jack.
98
F)ZONE2 SET
MAX VOL.
Adjusts the maximum volume level in Zone 2.
99
INIT. VOL.
Sets the volume level of Zone 2 when you turn on the power of this
unit.
99
D)INIT. CONFIG
Parameter
■ Signal information SIGNAL INFO
Use this feature to check audio and video signal information (see page 46).
ADVANCED
OPERATION
English
83 En
Customizing this unit (MANUAL SETUP)
4
Use the remote control to access and adjust each
parameter.
y
• You can change the “SET MENU” parameters while this unit is
reproducing sound.
• If you press SPARAMETER during the “SET MENU”
operation, the “SET MENU” operation is canceled.
• Press 9RETURN to return to the previous menu level.
Press 5AMP and then MMENU to enter
“SET MENU”.
The top “SET MENU” display appears in the OSD.
2
Press 8k / n to select “MANUAL SETUP”.
3 SOUND MENU
. A)EQUALIZER
B)LFE LEVEL
C)DYNAMIC RANGE
D)LIPSYNC
E)EXTD SUR.
[]/[]: Up/Down
[ENTER]: Enter
[
1
Press 8k / n repeatedly and then press
8ENTER to select and enter the desired
menu.
The following displays are examples where “SOUND
MENU” is selected.
5
SET MENU
;AUTO SETUP
. ;MANUAL SETUP
p
Using SET MENU
Press 8k / n repeatedly and then press
8ENTER to select and enter the desired
submenu.
The following display is an example where “LFE
LEVEL” is selected.
;SIGNAL INFO
B)LFE LEVEL
. SPEAKER;;;;;;0dB
HEADPHONE;;-20dB
Press 8ENTER to enter “MANUAL SETUP”.
The “MANUAL SETUP” display appears in the
OSD.
6
Press 8k / n to select the desired parameter
and then 8l / h to change the parameter
settings.
• Press 8h to increase the value.
• Press 8l to decrease the value.
7
Press MMENU to exit from “SET MENU”.
MANUAL SETUP
. 1 BASIC MENU
2
3
4
5
p
[]/[]: Up/Down
[p]/[[]: Adjust
[
3
p
[
[]/[]: Up/Down
[ENTER]: Enter
VOLUME MENU
SOUND MENU
INPUT MENU
OPTION MENU
84 En
p
[
[]/[]: Up/Down
[ENTER]: Enter
Customizing this unit (MANUAL SETUP)
1 BASIC MENU
Use this feature to manually adjust the basic speaker
settings. Most of the “BASIC MENU” parameters are set
automatically when you run the automatic setup.
LFE/bass out LFE/BASS OUT
Use this feature to select the speakers that output the LFE
(low-frequency effect) and the low-frequency signals.
A)SPEAKER SET
LFE/BASS OUT
1 BASIC MENU
. A)SPEAKER SET
B)SP LEVEL
C)SP DISTANCE
D)TEST TONE
SWFR
p
[
[]/[]: Up/Down
[ENTER]: Enter
FRONT >BOTH
LFE signals output
Subwoofer(s) and speakers
y
Set “TEST TONE” to “ON” to output the test tone for the
“SPEAKER SET”, “SP LEVEL” and “SP DISTANCE”.
Choice
Subwoofer(s)
Front
speakers
Other
speakers
■ Speaker settings A)SPEAKER SET
BOTH
Output
No output
No output
y
SWFR
Output
No output
No output
To select the desired parameter, press 8k / n repeatedly.
FRONT
No output
Output
No output
Extra speakers assignment EXTRA SP ASSIGN
Selects the function of the speakers connected to the
EXTRA SP terminals.
Subwoofer(s)
Front
speakers
Other
speakers
BOTH
*1
*2
*3
SWFR
*4
*3
*3
FRONT
No output
*1
*3
p
[
Subwoofer(s) and speakers
Choice
*1
Choice
Descriptions
ZONE2
Select this setting when you use the Zone 2
speakers (see page 104).
FRONT B
Select this setting when you use another front
speaker system in the main zone (see page 43).
ZONE B
Select this setting when you use another front
speaker system in another room (see page 43).
PRESENCE
Select this setting when you use the presence
speakers (see page 13).
NONE
Select this setting when you do not use the
EXTRA SP terminals.
*2
*3
*4
ADVANCED
OPERATION
XA)SPEAKER SET
X
EXTRA SP ASSIGN
X
ZONE2 >FRONT B
X
ZONE B PRESENCE
X
NONE
X
X
X
X
ZONE2 SET
XXXX[]/[]:Up/DownXXXXX
Not Available
XXXX[p]/[[]:EnterXXXXXXX
X
Low-frequency signals output
Output(s) the low-frequency signals of the front
channels and other speakers set to “SMALL”.
Always output the low-frequency signals of the front
channels.
Output the low-frequency signals if the speakers are set
to “LARGE”.
Outputs the low-frequency signals of the speakers set to
“SMALL” or “NONE”.
Notes
• This parameter shares the value with the “EXTRA SP
ASSIGN” parameter in “AUTO SETUP” (see page 33).
• If you select “ON” in “BI-AMP” (see page 109), you cannot
select “PRESENCE” or “ZONE2” in “EXTRA SP ASSIGN”.
• After changing the “EXTRA SP ASSIGN” setting, carry out
“AUTO SETUP” again (see page 32).
English
85 En
Customizing this unit (MANUAL SETUP)
Measure for the speaker size
The woofer section of a speaker is
– 16 cm (6.5 in) or larger: large
– smaller than 16 cm (6.5 in): small
Surround left/right speakers SUR. L/R SP
A)SPEAKER SET
SUR. L/R SP
Front speakers FRONT SP
NONE >SMALL
LARGE
A)SPEAKER SET
FRONT SP
Choice
SMALL
>LARGE
Choice
Descriptions
LARGE
Select this setting when the front speakers are
large.
SMALL
Select this setting when the front speakers are
small.
Descriptions
LARGE
Select this setting when the surround speakers
are large.
SMALL
Select this setting when the surround speakers
are small.
NONE
Select this setting when you do not use the
surround speakers. This unit is set to the Virtual
CINEMA DSP mode (see page 51), and “SUR.B
L/R SP” is automatically set to “NONE”.
Surround back left/right speakers
SUR.B L/R SP
Note
A)SPEAKER SET
When “LFE/BASS OUT” is set to “FRONT”, you can select only
“LARGE” in “FRONT SP”. If the value of “FRONT SP” is set to
other than “LARGE” in advance, this unit change the value to
“LARGE” automatically.
SUR.B L/R SP
SMLx1 >SMLx2
Center speaker CENTER SP
Choice
A)SPEAKER SET
LRGx1
Descriptions
LRGx1
Select this setting when the single surround back
speaker is large.
LRGx2
Select this setting when the surround back left
and right speakers are Large.
SMLx1
Select this setting when the single surround back
speaker is small.
When the center speaker is large:
Select “LARGE” (large).
SMLx2
Select this setting when the surround back left
and right speakers are small.
When the center speaker is small:
Select “SMALL” (small).
NONE
Select this setting when you do not use the
surround back speakers. The surround back
channel signals are directed to the surround left
and right speakers.
CENTER SP
NONE >SMALL
LARGE
When you do not use the center speaker:
Select “NONE” (none). The center channel signals are
directed to the front left and right speakers.
Note
Choice
Descriptions
LARGE
Select this setting when the center speaker is
large.
SMALL
Select this setting when the center speaker is
small.
NONE
Select this setting when you do not use the center
speaker. The center channel signals are directed
to the front left and right speakers.
86 En
If the Dolby TrueHD audio signals are input and “SUR.B L/R
SP” is set to “NONE”, the left and right surround back channels
are not directed to the surround left and right speakers.
Customizing this unit (MANUAL SETUP)
Bass cross over CROSS OVER
Use this feature to select the crossover frequency of all the
speakers set to “SML” (or “SMALL”) in “SPEAKER
SET” (see page 85). All frequencies below the selected
frequency will be sent to the subwoofer(s) or front
speakers depending on the setting of “LFE/BASS OUT”
in “SPEAKER SET” (see page 85).
Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
A)SPEAKER SET
■ Speaker level B)SP LEVEL
Use this feature to manually balance the speaker levels
between the front left or surround left speakers and each
speaker selected in “SPEAKER SET” (see page 85).
Control range: –10.0 dB to +10.0 dB
Control step: 0.5 dB
Initial setting:
FR.L/FR.R/SWFR/PR.L/PR.R: 0 dB
CNTR/SUR.L/SUR.R/SBL/SBR: –1.0 dB
B)SP LEVEL
1/2
B)SP LEVEL
2/2
CROSS OVER
. FR.L
. SBL
FR.R
CNTR
SUR.L
SUR.R
SBR
SWFR
FREQ;;;;80Hz
y
If your subwoofer can adjust the output volume and the crossover
frequency, set the volume to about half way (or slightly less) and
set the crossover frequency to the maximum.
Subwoofer phase SUBWOOFER PHASE
Use this feature to switch the phase of your subwoofer if
bass sounds are lacking or unclear.
A)SPEAKER SET
>NORMAL
Choice
REVERSE
Functions
NORMAL
(normal)
Does not change the phase of your subwoofer.
REVERSE
(reverse)
Sets the phase of your subwoofer to reverse.
Adjusted speaker
FR.L
Front left speaker
FR.R
Front right speaker
CNTR
Center speaker
SUR.L
Surround left speaker
SUR.R
Surround right speaker
SBL
Surround back left speaker
SBR
Surround back right speaker
SWFR
Subwoofer
PR.L
Presence left speaker
PR.R
Presence right speaker
ADVANCED
OPERATION
SUBWOOFER PHASE
SP LEVEL
y
• If your subwoofer can adjust the output volume and the
crossover frequency, set the volume to about half way (or
slightly less) and set the crossover frequency to the maximum.
• Set “TEST TONE” to “ON” to output the test tone for the
“SPEAKER LEVEL” setting (see page 88).
Notes
• The available speaker channels differ depending on the setting
of the speakers.
• Instead of “SBL” and “SBR”, “SB” is displayed if “SUR. B L/R
SP” is set to either “SMLx1” or “LRGx1” (see page 86).
English
87 En
Customizing this unit (MANUAL SETUP)
■ Speaker distance C)SP DISTANCE
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
1/2
C)SP DISTANCE
■ Test tone D)TEST TONE
Turns the test tone output on or off for the “SPEAKER
SET”, “SP LEVEL”, and “SP DISTANCE” settings.
2/2
D)TEST TONE
. UNIT;;;;;;;;feet
. SBL;;;;;;;;8.0ft
FRONT L;;;10.0ft
FRONT R;;;10.0ft
CENTER;;;;;8.5ft
SUR. L;;;;;8.0ft
SUR. R;;;;;8.0ft
>OFF
SBR;;;;;;;;8.0ft
SWFR;;;;;;;10.0ft
PRNS L;;;;;10.0ft
PRNS R;;;;;10.0ft
[
[]/[]: Up/Down
[p]/[[]: Adjust
p
[]/[]: Up/Down
[p]/[[]: Select
[
• The available speaker channels differ depending on the setting
of the speakers.
• Instead of “SBL” and “SBR”, “SUR.B” is displayed if “SUR.B
L/R SP” is set to either “SMLx1” or “LRGx1” (see page 86).
Unit for the speaker distance adjustment UNIT
Initial setting:
[U.S.A. and Canada models]: feet (ft)
[Other models]: meters (m)
Choice
ON
p
C)SP DISTANCE
Notes
Functions
meters (m)
Adjusts speaker distances in meters.
feet (ft)
Adjusts speaker distances in feet.
[p]/[[]: Select
[ENTER]: Return
Choice
Functions
OFF
This unit does not output the test tone for the
“SPEAKER SET”, “SP LEVEL”, and “SP
DISTANCE” settings.
ON
This unit outputs the test tone for the
“SPEAKER SET”, “SP LEVEL”, and “SP
DISTANCE” settings.
y
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial setting:
FRONT L/FRONT R/SWFR/PRNS L/
PRNS R: 3.00 m (10.0 ft)
CENTER: 2.60 m (8.5 ft)
SUR. L/SUR. R/SBL/SBR: 2.40 m (8.0 ft)
SP DISTANCE
Adjusted speaker
FRONT L
Front left speaker
FRONT R
Front right speaker
CENTER
Center speaker
SUR. L
Surround left speaker
SUR. R
Surround right speaker
SBL
Surround back left speaker
SBR
Surround back right speaker
SWFR
Subwoofer
PRNS L
Presence left speaker
PRNS R
Presence right speaker
88 En
If you use a handheld sound pressure level meter, hold at arm’s
length and point upwards so that the meter is in the listening
position. With the meter set to the 70 dB scale and to C SLOW,
calibrate each speaker to 75 dB.
Note
This function is automatically turned off if you exit from “BASIC
MENU”.
Customizing this unit (MANUAL SETUP)
2 VOLUME MENU
Use this menu to manually adjust the various volume
settings.
Adaptive DSP level ADAPTIVE DSP LEVEL
Use this feature to make fine adjustments of the DSP
effect level (see page 73) automatically in conjunction
with the volume level.
Choice
2 VOLUME MENU
AUTO
OFF
Does not adjust the DSP effect level
automatically.
. ADAPTIVE DRC;;;;OFF
ADAPTIVE DSP
LEVEL;;;;OFF
MUTE TYPE;;;;FULL
MAX VOL.;;;;+16.5dB
INIT. VOL.;;;;;;OFF
Functions
Adjusts the DSP effect level in conjunction with
the volume level.
p
[
[]/[]: Up/Down
[p]/[[]: Select
Note
Output level
AUTO
OFF
Input level
OFF
Input level
VOLUME: low
Choice
AUTO
VOLUME: high
Functions
AUTO
Adjusts the dynamic range automatically.
OFF
Does not adjust the dynamic range automatically.
y
• You can also adjust the dynamic range of the bitstream signal
sources by using “DYNAMIC RANGE” in “SOUND MENU”
(see page 91).
• This function is also useful for listening with your headphones.
Note
The adaptive dynamic range control feature does not function
when this unit is in the Pure Direct mode (see page 52).
Even if you set “ADAPTIVE DSP LEVEL” to “AUTO”, this unit
does not change but the fine-tunes the specified value of “DSP
LEVEL” (see page 73).
Muting type MUTE TYPE
Use this feature to adjust how much the mute function
reduces the output volume (see page 45).
Choice
Functions
FULL
Mutes all the audio output.
–20dB
Reduces the current volume by 20 dB.
Maximum volume MAX VOL.
Use this feature to set the maximum volume level in the
main zone. This feature is useful to avoid the unexpected
loud sound by mistake. For example, the original volume
range is –80.0 dB to +16.5 dB. However, when “MAX
VOL.” is set to –5.0 dB, the volume range becomes
–80.0 dB to –5.0 dB.
Control range: –30.0 dB to +15.0 dB, +16.5 dB
Control step: 5.0 dB
ADVANCED
OPERATION
Output level
Adaptive dynamic range control
ADAPTIVE DRC
Use this feature to adjust the dynamic range in
conjunction with the volume level. This feature is useful
when you are listening at lower volumes or at night. When
“ADAPTIVE DRC” is set to “AUTO”, this unit controls
the dynamic range as follows:
– If the VOLUME setting is low:
the dynamic range is narrow
– If the VOLUME setting is high:
the dynamic range is wide
Notes
• When this unit is in the auto setup procedure, the volume level
is automatically set to 0 dB regardless of the current “MAX
VOL.” setting.
• The “MAX VOL.” setting takes priority over the initial volume
setting. For example, if “INI.VOL.” is set to –20.0 dB and
“MAX VOL.” is set to –30.0 dB, the volume level is
automatically set to –30.0 dB when you turn on the power of
this unit next time.
• Use “MAX VOL.” in “ZONE SET” to set the initial volume
level in Zone 2.
Initial volume INIT. VOL.
Use this feature to set the volume level of the main zone
when the power of this unit is turned on.
Choices: OFF, MUTE, –80.0 dB to +16.5 dB
Control step: 0.5 dB
The “MAX VOL.” setting takes priority over the initial volume
setting.
89 En
English
Note
Customizing this unit (MANUAL SETUP)
Use this feature to adjust the audio parameters.
3 SOUND MENU
. A)EQUALIZER
B)LFE LEVEL
C)DYNAMIC RANGE
D)LIPSYNC
E)EXTD SUR.
Graphic equalizer GEQ
Use this feature to match the tonal quality of the center,
surround L/R and surround back L/R, and surround back
speakers with that of the front L/R speakers. You can
adjust 7 frequency bands (63 Hz, 160 Hz, 400 Hz, 1 kHz,
2.5 kHz, 6.3 kHz, 16 kHz).
Control range: –6.0 dB to +6.0 dB
Control step: 0.5 dB
p
[
[]/[]: Up/Down
[ENTER]: Enter
A)EQUALIZER
A)EQUALIZER
1/2
Equalizer type select EQ TYPE SELECT
Use this feature to select the type of equalizer.
. 2.5kHz
6.3kHz
16kHz
0dB
0dB
0dB
[]/[]: Up/Down
[p]/[[]: Adjust
[
[
Use this feature to select the parametric equalizer or the
graphic equalizer.
0dB
0dB
0dB
0dB
p
63Hz
160Hz
400Hz
1kHz
[]/[]: Up/Down
[p]/[[]: Select
■ Equalizer A)EQUALIZER
2/2
TEST >OFF ON
CHANNEL;;;;FRONT L
TEST >OFF ON
. CHANNEL;;;;FRONT L
p
3 SOUND MENU
y
Press 8k / n to select a frequency band and 8l / h to adjust
the selected frequency band.
A)EQUALIZER
OFF
[p]/[[]: Select
[ENTER]: Enter
Functions
AUTO PEQ
Uses the parametric equalizer adjusted in
“AUTO SETUP” (see page 33).
GEQ
Adjusts the built-in 7-frequency band graphic
equalizer so that the tonal quality of the speakers
matches. Press 8ENTER to display the graphic
equalizer screen.
OFF
The “GEQ” parameter can be adjusted only when “GEQ” is
selected in “EQ TYPE SELECT”.
Test tone TEST
Use this feature to make adjustments of “GEQ” while
listening to a test tone. To select “TEST”, press 8 k / n
repeatedly in the graphic equalizer screen.
A)EQUALIZER
1/2
. TEST
>OFF ON
CHANNEL;;;;FRONT L
63Hz
160Hz
400Hz
1kHz
[]/[]: Up/Down
[p]/[[]: Select
Deactivates the equalizing feature.
[
Choice
Note
0dB
0dB
0dB
0dB
p
EQ TYPE SELECT
AUTO PEQ >GEQ
[NATURAL]
y
Currently applied parametric equalizer type (see page 33) appears
under “AUTO PEQ”.
Choice
OFF
Does not output test tones and output the
currently selected source component.
ON
Outputs test tones from the selected speakers.
Note
You can select “AUTO PEQ” only when you carry out “AUTO
SETUP” in advance (see page 32). In this case, “AUTO PEQ” is
automatically selected as the default setting.
90 En
Functions
Customizing this unit (MANUAL SETUP)
■ Low-frequency effect level
■ Dynamic range C)DYNAMIC RANGE
B)LFE LEVEL
Use this feature to adjust the output level of the LFE (lowfrequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective when the input
signal contains the LFE channel.
Control range: –20 to 0 dB
Control step: 1 dB
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding bitstream signals.
C)DYNAMIC RANGE
SPEAKER;;;;;;;;;MAX
. HEADPHONE;;;;;;;MAX
p
[
[]/[]: Up/Down
[p]/[[]: Select
B)LFE LEVEL
. SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB
p
[
[]/[]: Up/Down
[p]/[[]: Adjust
Speakers SPEAKER
Adjusts the speaker LFE level.
Speakers SPEAKER
Adjusts the dynamic range compression for the speakers.
Headphones HEADPHONE
Adjusts the dynamic range compression for the
headphones.
Choice
Headphones HEADPHONE
Adjusts the headphone LFE level.
• MIN: Adjusts the dynamic range to narrow
when this unit is decoding bitstream signals
(except Dolby TrueHD).
• AUTO: Adjusts the dynamic range according
to the instruction of the input source signals
when this unit is decoding Dolby TrueHD
signals.
STD
Adjusts the dynamic range to medium. When
this unit is decoding Dolby TrueHD signals, the
dynamic range control is always active
regardless of the instruction of the input source
signals.
MAX
Preserves the greatest amount of dynamic range.
ADVANCED
OPERATION
MIN/AUTO
Note
Depending on the settings of “LFE/BASS OUT” (see page 85),
some signals may not be output at the SUBWOOFER PRE OUT
jack.
Functions
English
91 En
Customizing this unit (MANUAL SETUP)
■ Audio and video synchronization
(lip sync) D)LIPSYNC
Use this feature to adjust the audio and video
synchronization.
■ Extended surround E)EXTD SUR.
Use this feature to enjoy 6.1/7.1-channel playback for
multi-channel sources using the Dolby Pro Logic IIx,
Dolby Digital EX, or DTS-ES decoders by using the
connected surround back speakers.
D)LIPSYNC
E)EXTD SUR.
. HDMI AUTO;;;;;;OFF
AUTO;;;;;;;;;---ms
(offset;;;---ms)
MANUAL;;;;;;;;;0ms
. EXTD SUR.;;;;;;AUTO
p
[
[]/[]: Up/Down
[p]/[[]: Select
HDMI automatic lip sync mode HDMI AUTO
If the connected video monitor is connected to the HDMI
OUT jack of this unit and compatible with the automatic
audio and video synchronization function (automatic lip
sync), this unit adjusts the audio and video
synchronization automatically. Use this feature to activate
or deactivate the automatic lip sync.
Choices: ON, OFF
If the connected video monitor is compatible
with the automatic lip sync:
Select “ON”. Use “AUTO” to make fine adjustments of
the audio and video synchronization.
If the video monitor is not compatible with the
automatic lip sync or you do not want to use
the automatic lip sync:
Select “OFF”. Use “MANUAL” to adjust the audio and
video synchronization.
Auto delay AUTO
Use this feature to make fine adjustments of the audio and
video synchronization when you set “HDMI AUTO” to
“ON”.
Control range: 0 to 240 ms
Control step: 1 ms
y
“offset” indicates the difference between the value of the audio
delay that this unit sets automatically and the value of the audio
delay that you set in “AUTO”. This unit stores the value of
“offset” and applies the value to other automatic lip sync
compatible video monitors.
Manual delay MANUAL
Use this feature to adjust the delay of the sound output
manually to synchronize audio with video images when
you set “HDMI AUTO” to “OFF”.
Control range: 0 to 240 ms
Control step: 1 ms
92 En
[p]/[[]: Select
[ENTER]: Return
Choice
Functions
AUTO
Activates the optimum decoder to play back
signals in 6.1/7.1 channels when this unit
recognizes a signal flag being input.
PLIIxMovie
Plays back Dolby Digital or DTS signals in 7.1
channels using the Pro Logic IIx movie decoder.
PLIIxMusic
Plays back Dolby Digital or DTS signals in 6.1/
7.1 channels using the Pro Logic IIx music
decoder.
EX/ES
Plays back Dolby Digital or DTS signals in 6.1/
7.1 channels using the Dolby Digital EX or DTSES decoder.
OFF
Does not use any decoders to create 6.1/7.1
channels.
Customizing this unit (MANUAL SETUP)
4 INPUT MENU
Use this menu to adjust the parameters of each input
source.
1/2
p
[
B)
XM
C)
TUNER
D)
CD
E) MD/CD-R
F)
DVD
G) DTV/CBL
[]/[]: Up/Down
[ENTER]: Enter
4 INPUT MENU
. H)
I)
J)
K)
L)
M)
2/2
V-AUX
DOCK
BLUETOOTH
DVR
VCR
MULTI CH
[]/[]: Up/Down
[ENTER]: Enter
p
. A) SIRIUS
[
4 INPUT MENU
Input/output assignment
I/O ASSIGNMENT
Use this feature to assign the input/output jacks according
to the component to be used if the initial settings of this
unit do not correspond to your needs. Change the
parameter to reassign the respective jacks and effectively
connect more components.
Once the input/output jacks are reassigned, you can select
the corresponding component by using the RINPUT
selector on the front panel (or the input selector buttons on
the remote control).
K)
Input source
Parameter
INPUT RENAME
VOL. TRIM
PARENTAL LOCK
B)XM
(U.S.A. and Canada
models only)
INPUT RENAME
VOL. TRIM
C)TUNER
INPUT RENAME
VOL. TRIM
M)MULTI CH
INPUT RENAME
VOL. TRIM
BGV
INPUT CH
FRONT
D)CD
E)MD/CD-R
F)DVD
G)DTV/CBL
H)V-AUX
K)DVR
L)VCR
INPUT RENAME
VOL. TRIM
DECODER MODE
I)DOCK
INPUT RENAME
VOL. TRIM
STANDBY CHARGE
J)BLUETOOTH
INPUT RENAME
VOL. TRIM
START PAIRING
COAXIAL IN;;;;NONE
OPTICAL IN;;;;NONE
HDMI IN;;;;;;;;[3]
Current( DTV/CBL )
[p]/[[]: Select
[ENTER]: Enter
y
• “NONE” appears in the OSD when any input source is not
assigned to the input/output jack.
• You cannot select a specific item more than once for the same
type of jack.
• An asterisk (*) appears to the right of the input/output jack
names that have been changed from their previous settings.
• The currently assigned input source for the selected input/
output jack appears in the OSD (“Current( DTV/CBL )” in the
display example above).
ADVANCED
OPERATION
A)SIRIUS
(U.S.A. and Canada
models only)
DVR
. COMPONENT IN;;;[B]*
Note
Some parameters described above may not be available for all
input sources and some parameters are only available for specific
input sources.
English
93 En
Customizing this unit (MANUAL SETUP)
Input rename INPUT RENAME
Use this feature to change the name of the input source
that appears in the OSD and in the front panel display.
K)
DVR
Decoder mode DECODER MODE
Use this feature to switch the decoder activation mode.
When you select “DTS” and digital audio signals are
input, this unit always activates the DTS decoder and only
plays back the DTS digital audio signals.
INPUT RENAME
DVR .
D)
DVR
p
[p]/[[]: Position
[ ]/[ ]: Character
[ENTER]: Enter
[RETURN]: Return
[
CD
I/O ASSIGNMENT
INPUT RENAME
VOL. TRIM;;;;;0.0dB
. DECODER MODE;;;AUTO
1
2
Press 8l / h to place the “_” (underscore)
under the space or the character you want to
edit.
Press 8k / n to select the character you
want to use and then press 8l / h to move
to the next space.
Choice
p
[
[]/[]: Up/Down
[p]/[[]: Select
Functions
AUTO
Automatically detects digital audio signal input
types and selects the appropriate decoder.
DTS
Activates the DTS decoder and plays back only
DTS digital audio signals when digital audio
signals are input.
Notes
Note
• You can use up to 9 characters for each input.
• Press 8n to change the character in the following order,
or press 8k to go in the reverse order:
A to Z, 0 to 9, a to z, symbols (#, *, –, +, etc.), space.
“DECODER MODE” is only available when the digital audio
input jacks (HDMI, OPTICAL, and/or COAXIAL) are assigned
to the selected input source.
3
Repeat steps 1 through 2 to rename each
input source.
4
Press 8ENTER to complete.
Volume trim VOL. TRIM
Use this feature to adjust the level of the signal input at
each jack. This feature is useful if you want to balance the
level of each input source to avoid sudden changes in
volume when switching between input sources.
Control range: –6.0 dB to +6.0 dB
Control step: 0.5 dB
Initial setting: 0.0 dB
C)
TUNER
INPUT RENAME
. VOL. TRIM;;;;+6.0dB
p
[
[]/[]: Up/Down
[p]/[[]: Adjust
y
This parameter also affects the signals output at the audio ZONE
OUT jacks.
94 En
SIRIUS Satellite Radio parental lock
PARENTAL LOCK
Use this feature to set the code number for locking the
desired SIRIUS Satellite Radio channels. Refer to “Setting
the Parental Lock” on page 65 for details.
Charge on standby STANDBY CHARGE
Use this feature to select whether this unit charges the
battery of the stationed iPod or not when this unit is in the
standby mode.
Choice
Functions
AUTO
Charges the battery of the stationed iPod when
this unit is turned on and in the standby mode.
OFF
Charges the battery of the stationed iPod only
when this unit is turned on.
Customizing this unit (MANUAL SETUP)
To ensure security, a time limit of 8 minutes is set for
the pairing operation. You are recommended to read
and fully understand all the instructions before starting.
2
3
Press 8ENTER to start pairing.
The connected Bluetooth adapter starts searching
Bluetooth components. “Searching...” appears in the
video monitor.
Automatically selects the last selected video
source as the background video source.
DVD, DTV/
CBL, DVR,
VCR, V-AUX
Selects the corresponding input source as the
background video source.
OFF
Does not play the video source in the
background.
Input channels INPUT CH
Use this setting to select the number of channels input
from an external decoder (see page 25).
Choices: 6CH, 8CH
M) MULTI CH
INPUT RENAME
VOL. TRIM;;;;;0.0dB
BGV;;;;;;;;;;;;LAST
. INPUT CH;;;;;;;;6CH
To cancel the pairing, press 9RETURN to exit from
“START PAIRING”.
Press 9RETURN to exit from “START
PAIRING”.
Notes
• If the connected Bluetooth adapter cannot find any Bluetooth
components, “Not found” appears.
• If a Bluetooth adapter is not connected to this unit, “No
Bluetooth Adapter” appears.
[]/[]: Up/Down
[ENTER]: Select
If the connected component outputs discrete
6-channel audio signals.
Select “6CH”.
If the connected component outputs discrete
8-channel audio signals.
Select “8CH”. Also set “FRONT” (see below) to the
analog audio jacks at which the front left and right
channel signals output from the connected component
are input.
ADVANCED
OPERATION
y
4
LAST
Check that the Bluetooth component detects
the Bluetooth adapter.
If the Bluetooth component the Bluetooth adapter,
“YBA-10 YAMAHA” (example) appears in the
Bluetooth device list.
Select the Bluetooth adapter in the Bluetooth
device list and then enter the pass key
“0000” on the Bluetooth component.
Once this unit completes the pairing successfully,
“Pairing completed” appears.
Functions
[
1
Choice
p
Start pairing START PAIRING
Use this feature to start pairing the connected Yamaha
Bluetooth adapter (such as YBA-10, sold separately) with
your Bluetooth component. For details about the pairing,
refer to “Pairing the Bluetooth™ adapter and your
Bluetooth™ component” on page 70.
Front left and right channels input jack FRONT
If you selected “8CH” in “INPUT CH”, you can select the
analog audio jacks at which the front left and right channel
signals output from the connected external decoder is
input.
Choices: CD, MD/CD-R, DVD, DTV/CBL, DVR, VCR,
V-AUX
M) MULTI CH
Multi-channel input BGV BGV
Use this feature to select the video source played in the
background of the sources input at the MULTI CH INPUT
jacks.
INPUT RENAME
VOL. TRIM;;;;;0.0dB
BGV;;;;;;;;;;;;LAST
INPUT CH;;;;;;;;8CH
. FRONT;;;;;;;;;;;DVD
p
[
[]/[]: Up/Down
[ENTER]: Select
M) MULTI CH
INPUT RENAME
VOL. TRIM;;;;;0.0dB
. BGV;;;;;;;;;;;;LAST
INPUT CH;;;;;;;;6CH
p
[
[]/[]: Up/Down
[ENTER]: Select
Note
“FRONT” parameter appears only when you set “INPUT CH” to
“8CH”.
English
95 En
Customizing this unit (MANUAL SETUP)
5 OPTION MENU
Use this menu to adjust the optional system parameters.
Source feature OSD display time OSD-SOURCE
Use this feature to set the amount of time to display the
XM Satellite Radio information, SIRIUS Satellite Radio
information, or iPod menu in the OSD after you perform a
certain operation.
5 OPTION MENU
Choice
. A)DISPLAY SET
Functions
Displays the OSD unceasingly during an
operation.
[]/[]: Up/Down
[ENTER]: Enter
10S
Turns off the OSD 10 seconds after you perform
a certain operation.
30S
Turns off the OSD 30 seconds after you perform
a certain operation.
p
ON
[
B)VIDEO SET
C)MEMORY GUARD
D)INIT. CONFIG
E)HDMI SET
F)ZONE2 SET
■ Display settings A)DISPLAY SET
Note
Use “VIDEO” of “INIT” in “ADVANCED SETUP” to set “OSD
SHIFT” to the factory presets (see page 109).
A)DISPLAY SET
Amplifier function OSD display time OSD-AMP
Use this feature to set the amount of time to display the
status information screen after you perform a certain
operation.
Choice
. DIMMER;;;;;;;;;;;;0
OSD SHIFT;;;;;;;;+5
OSD-SOURCE;;;;;;30S
OSD-AMP;;;;;;;;;30S
FL SCROLL;;;;;;CONT
p
[
[]/[]: Up/Down
[p]/[[]: Adjust
Dimmer DIMMER
Use this feature to adjust the brightness of the front panel
display.
Control range: – 4 to 0
Control step: 1
• Press 8l to make the front panel display dimmer.
• Press 8h to make the front panel display brighter.
OSD shift OSD SHIFT
Use this feature to adjust the vertical position of the OSD.
Control range: –5 (downward) to +5 (upward)
Control step: 1
Initial setting: 0
• Press 8l to lower the position of the OSD.
• Press 8h to raise the position of the OSD.
96 En
Functions
ON
Displays the OSD unceasingly during an
operation.
10S
Turns off the OSD 10 seconds after you perform
a certain operation.
30S
Turns off the OSD 30 seconds after you perform
a certain operation.
Front panel display scroll FL SCROLL
Use this feature to set the mode to display the XM
Satellite Radio information, SIRIUS Satellite Radio
information, or iPod menu (such as song title or channel
name) in the front panel display.
Choice
Functions
CONT
Continuous mode.
Select this to display the operation status in the
front panel display in a continuous manner.
ONCE
Scroll-once mode.
Select this to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.
Customizing this unit (MANUAL SETUP)
■ Video settings B)VIDEO SET
Note
■ Memory guard C)MEMORY GUARD
Use this feature to prevent accidental changes to sound
field program parameter and other system settings.
Use “VIDEO” of “INIT” in “ADVANCED SETUP” to set the
parameters in “VIDEO SET” to the factory presets (see
page 109).
C)MEMORY GUARD
>OFF
ON
B)VIDEO SET
. VIDEO CONV.;;;;;;ON
[p]/[[]: Select
[ENTER]: Return
Choice
p
[
[]/[]: Up/Down
[p]/[[]: Select
Video conversion VIDEO CONV.
Use this feature to set whether to convert the video signals
input at the VIDEO, S VIDEO, and COMPONENT
VIDEO jacks.
Choice
Functions
ON
Converts composite, S-video, and component
video signals interchangeably and up-converts
composite, S-video, and component video
signals to HDMI video signals.
OFF
Does not convert any signals.
• This unit does not convert 480 line video signals and 576 line
video signals interchangeably.
• The analog component video signals with 480i (NTSC)/576i
(PAL) of resolution are converted into the S-video or composite
video signals and output at the S VIDEO MONITOR OUT and
VIDEO MONITOR OUT jacks.
• The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of video connections between each component.
• When composite video or S-video signals from a VCR are
converted into component video signals, the picture quality may
suffer depending on your VCR.
• Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set “VIDEO CONV.” to “OFF”.
OFF
Turns off the “MEMORY GUARD” feature.
ON
Protects:
– sound field program parameters
– “AUTO SETUP” items
– all speaker levels
– “MANUAL SETUP” items
Notes
• You can change the following parameters even if “MEMORY
GUARD” is set to “ON”:
– “EXTD SUR.” in “SOUND MENU” (see page 92)
– “DECODER MODE” in “INPUT MENU” (see page 94)
– “PARENTAL LOCK” in “INPUT MENU” (see page 94)
– “MEMORY GUARD”
• When “MEMORY GUARD” is set to “ON”, “ G ” appears at the
top right of the “SET MENU” screen.
• You can change the settings of “SUR.” in the sound field
program parameter screen (see page 77) even if “MEMORY
GUARD” is set to “ON”.
ADVANCED
OPERATION
Notes
Functions
English
97 En
Customizing this unit (MANUAL SETUP)
■ Initial configuration D)INIT. CONFIG
■ HDMI set E)HDMI SET
Use this feature to select the settings of the audio input
jack select, active decoders and extended surround when
you turn on this unit.
Use this feature to select the component to play back
HDMI audio signals.
E)HDMI SET
D)INIT. CONFIG
S. AUDIO;;;;HTR-6160
. AUDIO SELECT;;AUTO
DECODER MODE;;AUTO
EXTD SUR.;;;;;AUTO
[p]/[[]: Select
[ENTER]: Return
[p]/[[]: Select
[ENTER]: Return
Audio select AUDIO SELECT
Use this feature to designate the default audio input jack
select setting (see page 44) for the input sources connected
to the DIGITAL INPUT jacks when you turn on the power
of this unit.
Choice
Functions
AUTO
Automatically detects the type of input signals
and selects the appropriate audio input jack
select setting.
LAST
Automatically selects the last input jack select
setting used for the connected input source.
Decoder mode DECODER MODE
Use this feature to designate the default decoder mode
(see page 94) for the input sources connected to the
DIGITAL INPUT jacks when you turn on the power of
this unit.
Choice
Functions
AUTO
Automatically detects the type of input signals
and select the appropriate decoder mode setting.
LAST
Automatically selects the last decoder mode
setting used for the connected input source.
Extended surround EXTD SUR.
Use this feature to designate the extended decoder mode
(see page 92) for the input sources connected to the
DIGITAL INPUT jacks when you turn on the power of
this unit.
Choice
Functions
AUTO
Automatically detects the digital audio input
signals and activates the appropriate decoder.
LAST
Automatically selects the last decoder mode set
for “EXTD SUR.” in “SOUND MENU”.
98 En
Support audio S.AUDIO
Use this feature to select whether to play back HDMI
audio signals on this unit or on another HDMI component
connected to the HDMI OUT jack on the rear panel of this
unit.
Choice
Functions
HTR-6160
Plays back HDMI audio signals on this unit. The
HDMI audio signals input at the HDMI input
jacks of this unit are not output to the HDMI
component connected to the HDMI OUT jack on
the rear panel of this unit.
OTHER
Plays back HDMI audio signals on another
HDMI component connected to the HDMI OUT
jack.
Notes
• This unit transmits audio and video signals input at the HDMI
input jacks to the HDMI out jack only when this unit is turned
on even if “S.AUDIO” is set to “OTHER”.
• Available audio/video signals depend on the specification of the
connected video monitor. Refer to the instruction manual of
each connected component.
Customizing this unit (MANUAL SETUP)
■ Zone 2 settings F)ZONE2 SET
F)ZONE2 SET
. MAX VOL.;;;+16.5dB
INIT. VOL.;;;;;OFF
p
[
[]/[]: Up/Down
[p]/[[]: Adjust
Zone 2 Maximum volume MAX VOL.
Use this feature to set the maximum volume level in the
Zone 2.
Control range: –30.0 dB to +15.0 dB, +16.5 dB
Control step: 5.0 dB
Notes
• The “MAX VOL.” setting takes priority over the “INI.VOL.”
setting. For example, when “INI.VOL.” is set to –20.0 dB and
then “MAX VOL.” is set to –30.0 dB, the volume level is
automatically set to –30.0 dB when you turn on the power of
this unit next time.
• The “MAX VOL.” setting does not affect the output level at the
“ZONE 2 OUT” jacks.
ADVANCED
OPERATION
Zone 2 Initial volume INI.VOL.
Use this feature to set the volume level of Zone 2 when the
power of this unit is turned on.
Choices: OFF, MUTE, –80.0 dB to +16.5 dB
Control step: 0.5 dB
Notes
• The “MAX VOL.” setting takes priority over the “INI.VOL.”
setting.
• When you select “FRONT B”, “PRNS”, “Zone B”, or “NONE”
in “EXTRA SP ASSIGN” (see page 85), “Zone 2 SP Not
Assigned” appears in the OSD and the “ZONE2 SET”
parameter is not available.
• The “INI.VOL.” setting does not affect the output level at the
“ZONE 2 OUT” jacks.
English
99 En
REMOTE CONTROL FEATURES
Remote control features
In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha
and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code
for each input source (see page 102).
Controlling this unit, a TV, or other components
■ Controlling this unit
■ Controlling a TV
Press 5AMP to control this unit.
5AMP lights up for a few seconds after you press
5AMP and any buttons (expect input selector buttons)
when the remote control is controlling this unit.
Press 4DTV/CBL to control your TV. To control your
TV, you must set the appropriate remote control code for
DTV/CBL (see page 102).
POWER
POWER
POWER
TV
AV
STANDBY
POWER
MUTE
A
XM
SIRIUS
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
VCR
B
DTV/CBL
TV CH
STANDBY
POWER
AV
A
XM
SIRIUS
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
VCR
B
AMP
TV INPUT
TV MUTE
*1
TV INPUT
AMP
TV CH
*1
TV VOL
SCENE
1
TV VOL
TV MUTE
POWER
TV
AMP
2
3
4
SRCH MODE
VOLUME
MENU
BAND LEVEL
TITLE
SCENE
1
2
3
4
ENTER
SRCH MODE
MENU
VOLUME
BAND LEVEL
TITLE
DISPLAY
RETURN
MEMORY
ENTER
REC
*2
DISPLAY
RETURN
MEMORY
INFO
*2
REC
l
PROG h
1
2
ENHANCER SUR. DECODE
3
STRAIGHT PURE DIRECT
5
INFO
l
PROG h
1
2
6
9
3
0
10
8
SLEEP
ENT
4
PARAMETER
7
MULTI CH IN AUDIO SEL
9
0
4
PARAMETER
7
ENHANCER SUR. DECODE
STRAIGHT PURE DIRECT
5
6
MULTI CH IN AUDIO SEL
10
8
SLEEP
ENT
Notes
Notes
*1
These buttons always control your TV regardless of whether
you press 4DTV/CBL or not.
*1
These buttons always control this unit.
These buttons control this unit only when 5AMP is pressed.
*3 4A or B is the optional component control area button. You
can control the desired component without changing the input
source of this unit.
Remote control
*2
*2
Digital TV/Cable TV
TV POWER
Turns on or off the power.
TV CH +/–
Changes the channel number.
TV VOL +/–
Increases or decreases the volume
level.
TV INPUT
Changes the input source.
TV MUTE
Mutes the audio output.
These buttons control your TV only when 4DTV/CBL is
pressed. For details, see the “Digital TV/Cable TV” column on
page 101.
y
You can control more than one TV by setting the appropriate
remote control code for any input source selector buttons other
than 4DTV/CBL. In such a case, you can control the buttons
highlighted above (*1 and *2) when you press the input source
selector button.
100 En
Remote control features
■ Controlling other components
Press one of the input selector buttons (4) buttons to
control other components. You must set the appropriate
remote control code for each input source in advance (see
page 102). The following table shows the function of each
control button used to control other components assigned
to each input selector button. Be advised that some buttons
may not correctly operate the selected component.
[1]
[2]
POWER
POWER
TV
AV
A
STANDBY
POWER
XM
SIRIUS
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
TV CH
[3]
[4]
• The remote control has 13 modes (control areas) to control
components so that the remote control can operate up to 13
different components.
• When you press one of the optional component control area
buttons (A and B), you can control the desired component
without changing the input source of this unit.
RETURN
MEMORY
V-AUX/DOCK
VCR
B
AMP
TV INPUT
TV MUTE
[5]
TV VOL
SCENE
1
2
3
4
INFO
[6]
l
PROG h
1
2
ENHANCER SUR. DECODE
3
STRAIGHT PURE DIRECT
5
6
9
LD player
CD player
MD/CD
recorder
[1] AV POWER
Power *1
Power *2
Power *1
Power *1
Power *1
[2] TITLE
Title
0
4
PARAMETER
7
MULTI CH IN AUDIO SEL
Digital TV/
Cable TV
[3] PRESET/CH k
[8]
DISPLAY
DVD player/
VCR
recorder
Power *1
[7]
ENTER
REC
y
Remote control
SRCH MODE
MENU
VOLUME
BAND LEVEL
TITLE
10
8
SLEEP
ENT
[9]
Tuner
Band
VCR channel up Up
Preset up (1-8)/
Tuning up
PRESET/CH n
Down
VCR channel
down
Down
Preset down
(1-8)/Tuning
down
A-E/CAT. l
Left
Left
Preset down
(A-E)
A-E/CAT. h
Right
Right
Preset up
(A-E)
ENTER
Enter
Enter
Hold
[4] RETURN
Return
Return
Memory
[5] REC
Disc skip
(player)
Rec (recorder)
Rec
Rec *2
p
Play
Play
Play *2
w
Search
backward
Search backward
Search backward Search backward Search backward Information
Search backward
*2
f
Search forward
Search forward
e
Pause
b
Skip backward
a
Skip forward
Skip forward
s
Stop
Stop
[6] 1-9, 0, +10
Play
Search forward
*2
Search forward
Pause
Pause *2
Skip backward
Skip backward
*2
Disc skip
Rec
Play
Play
Search forward
Search forward
Pause
Pause
Pause
Skip backward
Skip backward
Skip backward
Skip forward *2 Skip forward
Skip forward
Skip forward
Stop *2
Stop
Stop
Stop
ADVANCED
OPERATION
Up
Preset stations
Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons (1-8)/Numeric
buttons
[7] MENU
Menu
[8] DISPLAY
Display
Display
Display
Display
Display
Display
Display
[9] ENT
Title/Index
Enter
Enter
Chapter/Time
Index
Index
Enter
Menu
Search mode
Notes
*1
*2
This button is operational only when the original remote control supplied with the component has a POWER button.
These buttons operate your DVD recorder only when you set the appropriate remote control code for DVR (see page 102).
English
101 En
Remote control features
Setting remote control codes
2
You can control other components by setting the
appropriate remote control codes. For a complete list of
available remote control codes, refer to “List of remote
control codes” at the end of this manual.
Remote control code default settings
Press the numeric buttons (0 to 9) (G) to
enter the four-digit remote control code for
the component to be used.
When the setting succeeds, 5AMP flashes twice;
however, when it does not, 5AMP flashes
repeatedly.
Notes
Input
source
Component
category
Manufacturer
Default
code
A
TUNER
Yamaha
5012
XM
TUNER
Yamaha
5009
SIRIUS
TUNER
Yamaha
5017
■ Resetting all remote control codes
CD
CD
Yamaha
5013
MD/CD-R
CD-R
Yamaha
5001
Use this feature to clear all the remote control codes
previously set and reset all of them to the initial factory
settings.
TUNER
TUNER
Yamaha
5007
DVD
DVD
Yamaha
2000
DTV/CBL
—
—
—
V-AUX
TUNER
Yamaha
5011
DVR
DVR
Yamaha
2011
B
TUNER
Yamaha
5009
• If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
• If you do not press any buttons within 30 seconds in step 2, the
setup process is canceled. If this happens, repeat the setup
procedure.
1
While pressing and holding 5AMP on the
remote control, press 2AV POWER for
more than 3 seconds.
5AMP flashes twice.
POWER
AMP
AV
While holding
down
Press for 3
seconds
Note
You may not be able to operate your Yamaha component even if a
Yamaha remote control code is preset as listed above. In this case,
try setting another Yamaha remote control code.
1
While pressing and holding one of the input
selector buttons (4) on the remote control to
select the control area you want to set up,
press 2AV POWER for more than 3
seconds.
5AMP flashes twice.
A
XM
SIRIUS
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
VCR
B
AMP
flashes
2
Press the numeric buttons (6) to enter the
code number “9981”.
When the setting succeeds, 5AMP flashes twice;
however, when it does not, 5AMP flashes
repeatedly.
y
POWER
AV
Press for 3
seconds
While holding down
AMP
flashes
102 En
If you do not press any buttons within 30 seconds after step 1, the
clearing process is canceled. In this case, repeat the clearing
procedure.
USING MULTI-ZONE CONFIGURATION
Using multi-zone configuration
This unit allows you to configure a multi-zone audio system. The Zone 2 feature allows you to set this unit to reproduce
separate input sources in the main zone and the second zone (Zone 2). You can control this unit from the second zone
using the supplied remote control.
Only analog signals are sent to the second zone. Any source you want to listen to in the second zone must be
connected to the analog AUDIO IN jacks of this unit.
Connecting Zone 2
You need the following additional equipment to use the multi-zone functions of this unit:
• An infrared signal receiver in the second zone.
• An infrared signal emitter in the main zone. This emitter transmits the infrared signals from the remote control via the
infrared signal receiver in the second zone to a CD player or a DVD player, etc. in the main zone.
• An amplifier and speakers in the second zone.
y
• Since there are many possible ways to connect and use this unit in a multi-zone configuration, we recommend that you consult with
your nearest authorized Yamaha dealer or service center about the Zone 2 connections that best meet your requirements.
• Some Yamaha models are able to connect directly to the REMOTE jacks of this unit. If you own these products, you may not need to
use an infrared signal emitter. Up to 6 Yamaha components can be connected as shown below.
REMOTE
REMOTE
Infrared signal
receiver
OUT
REMOTE
IN
OUT
Yamaha
component
This unit
REMOTE
IN
ADVANCED
OPERATION
IN
OUT
Yamaha
component
■ Using the external amplifier
Connect the amplifier/receiver in the second zone and other components to this unit as follows.
From the ZONE 2 OUT jacks
Amplifier
Main zone
Second zone
(Zone 2)
Infrared signal receiver
Remote control
DVD player (etc.)
This unit
Infrared signal emitter
From the REMOTE OUT jack
From the REMOTE IN jack
English
Note
To avoid unexpected noise, DO NOT USE the Zone 2 feature with CDs encoded in DTS.
103 En
Using multi-zone configuration
■ Using the internal amplifier of this unit
Important safety notice
The EXTRA SP speaker terminals of this Receiver should not be connected to a Passive Loudspeaker Selector Box or
more than one loudspeaker per channel.
Connection to a Passive Loudspeaker Selector Box or multiple speakers per channel could create an abnormally low
impedance load resulting in amplifier damage. See this owner’s manual for correct usage.
Compliance with minimum speaker impedance information for all channels must be maintained at all times. This
information is found on the back panel of your Receiver.
Connect the speakers in the second zone to the EXTRA SP speaker terminals and then set the “EXTRA SP ASSIGN” to
“ZONE2” (see page 85).
FRONT B/ZONE2/
PRESENCE
EXTRA SP L
R
Second zone
(Zone 2)
This unit
Main zone
y
• You can use the speakers connected EXTRA SP speaker terminals as the front speaker system of another zone. Set “EXTRA SP
ASSIGN” to “ZONE B” (see page 85).
• When you use the internal amplifiers for the Zone 2 speakers, you can adjust the volume level and set the initial volume level and
maximum volume level of the Zone 2 speakers (see page 99).
Controlling Zone 2
You can select and control Zone 2 by using the control
buttons on the front panel or on the remote control. The
available operations are as follows:
• Selecting the input source of Zone 2.
• Tuning into FM or AM when “TUNER” is selected as
the input source of Zone 2 (see page 53).
• Tuning into XM Satellite Radio when “XM” is selected
as the input source of Zone 2 (see page 57) (U.S.A. and
Canada models only).
• Tuning into SIRIUS Satellite Radio when “SIRIUS” is
selected as the input source of Zone 2 (see page 62)
(U.S.A. and Canada models only).
• Enjoying music stored on your iPod stationed in a
Yamaha iPod universal dock (such as YDS-10 sold
separately) connected to the DOCK terminal of this
unit when “V-AUX” is selected as the input source
(see page 68).
Note
You must complete each step while the ZONE2 indicator is
flashing in the front panel display. Otherwise, the Zone 2 mode is
automatically canceled and this unit returns to the normal
operation mode. In this case, repeat the Zone 2 selection
procedure.
104 En
■ Controlling Zone 2 with the front panel
Turning on Zone 2
Press IZONE CONTROL to turn on Zone 2.
Activating the Zone 2 operation mode
Press IZONE CONTROL to control Zone 2.
The ZONE2 indicator flashes in the front panel display for
approximately 10 seconds.
ZONE2
Flashes
Using multi-zone configuration
Operate the following operations after activating the Zone 2
operation mode.
■ Controlling Zone 2 with the remote
control
Operating Zone 2
Turning on Zone 2
Press RINPUT l / h to select the desired input
source while the ZONE2 indicator is flashing in
the front panel display.
While pressing and holding 5AMP, press
HPOWER.
• Select “TUNER” as the input source to use the TUNER
features in Zone 2. For details about the TUNER
operations, see “FM/AM tuning” on page 53.
• Select “XM” as the input source to use the XM
Satellite Radio features in Zone 2. For details about the
XM Satellite Radio operations, see “XM Satellite
Radio tuning” on page 57.
• Select “SIRIUS” as the input source to use the SIRIUS
Satellite Radio features in Zone 2. For details about the
SIRIUS Satellite Radio operations, see “SIRIUS
Satellite Radio™ tuning” on page 62.
• Select “V-AUX” as the input source to use iPod
features in Zone 2. For details about the iPod
operations, see “Using iPod™” on page 68.
• Select “V-AUX” as the input source to use Bluetooth
component features in Zone 2. For details about the
Bluetooth component operations, see “Using
Bluetooth™ components” on page 70.
Press HZONE 2 ON/OFF to set Zone 2 to the
standby mode.
AMP
POWER
Operating Zone 2
While pressing and holding 5AMP, press one of
the input selector buttons (4) to select the
desired input source of Zone 2.
Notes
JMUTE and EVOLUME +/– are available to control Zone2
with same procedure as mentioned above.
Setting Zone 2 to the standby mode
While pressing and holding 5AMP, press
ISTANDBY to set ZONE 2 to the standby
mode.
ADVANCED
OPERATION
Set Zone 2 to the standby mode
While holding
down
y
Press LSYSTEM OFF to set the main zone and Zone 2 to the
standby mode simultaneously.
English
105 En
ADVANCED SETUP
Advanced setup
This unit has additional menus that are displayed in the front panel display. The advanced setup menu offers additional
operations to adjust and customize the way this unit operates. Change the initial settings (indicated in bold under each
parameter) to reflect the needs of your listening environment.
Notes
• The settings you make are reflected next time you press KMAIN ZONE ON/OFF to turn on this unit (see page 29).
• Only KMAIN ZONE ON/OFF, LSYSTEM OFF, MTONE CONTROL and the NPROGRAM selector are effective while you
are using the advanced setup menu.
• No other operations can be made while you are using the advanced setup menu.
• The advanced setup menu is only available in the front panel display.
Using the advanced setup
1
Press LSYSTEM OFF on the front panel to
set this unit to the standby mode.
2
Press and hold MTONE CONTROL and
then press KMAIN ZONE ON/OFF to turn
on this unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
■ Speaker impedance SP IMP.
Use this feature to set the speaker impedance of this unit
so that it matches that of your speakers.
Choices: 8Ω MIN, 6ΩMIN
• Select “8ΩMIN” to set the speaker impedance to 8 Ω.
• Select “6ΩMIN” to set the speaker impedance to 6 Ω.
SP IMP.
Speaker
Impedance level
If you use one set (A or B),
the impedance of each
speaker must be 8 Ω or
higher.
Front
TONE CONTROL
While holding
down
If you use two sets (A and
B), the impedance of each
speaker must be 16 Ω or
higher.*
MAIN ZONE
8ΩMIN
ON/OFF
Center
3
Rotate the NPROGRAM selector to select
the parameter you want to adjust.
The name of the selected parameter appears in the
front panel display.
Surround
Surround back
If you use one set (A or B),
the impedance of each
speaker must be 4 Ω or
higher.
SPIMP.-8MIN
Currently selected
parameter
4
5
Front
Currently selected
parameter setting
Center
Surround
Press LSYSTEM OFF to save the new
setting and set this unit to the standby mode.
The settings you made are reflected next time you turn on
this unit.
106 En
If you use two sets (A and
B), the impedance of each
speaker must be 8 Ω or
higher.
6ΩMIN
Press MTONE CONTROL repeatedly to
change the selected parameter setting.
y
The impedance of each
speaker must be 8 Ω or
higher.
The impedance of each
speaker must be 6 Ω or
higher.
Surround back
*
The Canada model cannot use two separate speaker systems
(A and B) simultaneously when “SP IMP.” is set to “8ΩMIN”.
Advanced setup
See page 106 for the operation of the advanced setup.
■ Remote control AMP ID REMOTE AMP
Use this feature to set the AMP ID of this unit for remote
control recognition. This feature is useful when you
operate this unit and the other Yamaha receivers/
amplifiers in the same room separately.
Choices: ID1, ID2
• Select “ID1” when the remote control AMP ID code is
set to “5019”.
• Select “ID2” when the remote control AMP ID code is
set to “5020”.
Setting remote control AMP ID codes
You need to set the remote control AMP ID code for the
remote control.
1
■ Remote control TUNER ID REMOTE TU
Use this feature to set the TUNER ID of this unit for
remote control recognition.
Choices: ID1, ID2
• Select “ID1” when the remote control TUNER ID code
is set to “5007”.
• Select “ID2” when the remote control TUNER ID code
is set to “5016”.
Setting remote control TUNER ID codes
You need to set the remote control TUNER ID library
code for the remote control.
1
While pressing and holding 4TUNER on the
remote control, press 2AV POWER for
more than 3 seconds.
5AMP flashes twice.
While pressing and holding 5AMP on the
remote control, press 2AV POWER for
more than 3 seconds.
5AMP flashes twice.
POWER
TUNER
AV
While holding
down
Press for 3
seconds
POWER
AMP
AV
While holding
down
Press for 3
seconds
AMP
2
AMP
flashes
2
Press the numeric buttons (G) to enter the
code number “5019” or “5020”.
When the setting succeeds, 5AMP flashes twice;
however, when it does not, 5AMP flashes
repeatedly.
AMP ID
code *1
Function
5019
To operate this unit using
(initial setting) the default code.
5020
*1
*2
To operate this unit using
an alternative code.
Remote
control AMP
ID *2
ID1
(initial setting)
Press the numeric buttons (G) to enter the
code number “5007” or “5016”.
When the setting succeeds, 5AMP flashes twice;
however, when it does not, 5AMP flashes
repeatedly.
TUNER ID
code *1
Function
5007
To operate this unit using
(initial setting) the default code.
5016
*1
*2
To operate this unit using
an alternative code.
ADVANCED
OPERATION
flashes
Remote
control
TUNER ID *2
ID1
(initial setting)
ID2
The remote control setting
The setting of this unit
ID2
The remote control setting
The setting of this unit
English
107 En
Advanced setup
See page 106 for the operation of the advanced setup.
■ Remote control XM ID REMOTE XM
(U.S.A. and Canada models only)
Use this feature to set the XM ID of this unit for remote
control recognition.
Choices: ID1, ID2
• Select “ID1” when the remote control XM ID code is
set to “5009”.
• Select “ID2” when the remote control XM ID code is
set to “5015”.
Setting remote control XM ID codes
You need to set the remote control XM ID code for the
remote control.
1
■ Remote control SIRIUS ID REMOTE SR
(U.S.A. and Canada models only)
Use this feature to set the SIRIUS ID of this unit for
remote control recognition.
Choices: ID1, ID2
• Select “ID1” when the remote control SIRIUS ID code
is set to “5017”.
• Select “ID2” when the remote control SIRIUS ID code
is set to “5018”.
Setting remote control SIRIUS ID codes
You need to set the remote control SIRIUS ID code for the
remote control.
1
While pressing and holding 3XM on the
remote control, press 2AV POWER for
more than 3 seconds.
5AMP flashes twice.
While pressing and holding KSIRIUS on the
remote control, press 2AV POWER for
more than 3 seconds.
5AMP flashes twice.
POWER
SIRIUS
POWER
XM
While holding
down
AV
While holding
down
AV
Press for 3
seconds
Press for 3
seconds
AMP
flashes
AMP
2
flashes
2
Press the numeric buttons (G) to enter the
code number “5009” or “5015”.
When the setting succeeds, 5AMP flashes twice;
however, when it does not, 5AMP flashes
repeatedly.
XM ID code
*1
Function
5009
To operate this unit using
(initial setting) the default code.
5015
*1
*2
To operate this unit using
an alternative code.
The remote control setting
The setting of this unit
108 En
Remote
control XM
ID *2
Press the numeric buttons (G) to enter the
code number “5017” or “5018”.
When the setting succeeds, 5AMP flashes twice;
however, when it does not, 5AMP flashes
repeatedly.
SIRIUS ID
code *1
5017
To operate this unit using
(initial setting) the default code.
5018
ID1
(initial setting)
*1
ID2
Function
*2
To operate this unit using
an alternative code.
The remote control setting
The setting of this unit
Remote
control
SIRIUS ID *2
ID1
(initial setting)
ID2
Advanced setup
See page 106 for the operation of the advanced setup.
■ SIRIUS Satellite Radio Parental Lock
personal identification number reset
SR PIN
Use this feature to set the code number (personal
identification number) for the SIRIUS Satellite Radio
Parental Lock feature to the initial factory setting. This
feature is useful when you forget or want to change the
current code number.
Choices: RESET, CANCEL
• Select “RESET” to set the code number to the initial
factory setting.
• Select “CANCEL” to set the code number to the initial
factory setting.
Note
Even if you set “SR PIN” to “RESET”, this unit does not unlock
the locked channels. The initial factory setting of the Parental
Lock code number is “0000”.
■ Parameter initialization INIT
Use this feature to reset the parameters of this unit to the
initial factory settings. You can select the category of
parameters to be initialized.
Choices: DSP PARAM, VIDEO, ALL, CANCEL
• Select “DSP PARAM” to initialize all the parameters
of the sound field programs (see page 72).
• Select “VIDEO” to initialize the parameters in
“VIDEO SET” (see page 97) and “OSD SHIFT” in
“DISPLAY SET” (see page 96).
• Select “ALL” to initialize all the parameters of this
unit.
• Select “CANCEL” to cancel the initialization
procedure.
Notes
• The advanced setup menu parameters are not initialized.
• Use “INITIALIZE” in the sound field program menu to
initialize the parameters of the desired program (see page 72).
■ Bi-amplifier setting BI-AMP
ADVANCED
OPERATION
Use this feature to activate or deactivate the bi-amplifier
function (see page 16).
Choices: ON, OFF
• Select “ON” if you want to activate the bi-amplifier
function. “SUR.B L/R SP” is set to “NONE”
automatically, and this unit outputs the front channel
audio signals at the SURROUND BACK/BI-AMP
speaker terminals.
• Select “OFF” if you want to deactivate the bi-amplifier
function.
Note
When “BI-AMP” is set to “ON”, you can only select “FRONT B”
or “NONE” in “EXTRA SP ASSIGN” (see page 85).
■ SCENE IR code setting SCENE IR
Use this feature to output the remote control signals at the
REMOTE OUT jack automatically when this unit is in the
SCENE mode.
Choices: ON, OFF
• Select “ON” when the component connected to the
REMOTE OUT jack is the Yamaha component and has
the capability of the SCENE control signals. This unit
automatically sends the remote control signals to the
component.
• Select “OFF” when the component connected to the
REMOTE OUT jack is not the Yamaha component and
does not have the capability of the SCENE control
signals.
Note
English
If noises are output when you operate the SCENE function, set
“SCENE IR” to “OFF”.
109 En
TROUBLESHOOTING
Troubleshooting
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
■ General
Problem
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
No sound.
No picture.
Cause
The power cable is not connected or the
plug is not completely inserted.
Remedy
Connect the power cable firmly.
See
page
—
The speaker impedance setting is incorrect. Set the speaker impedance to match your speakers.
28
The protection circuitry has been activated. Make sure that all speaker wire connections on this
unit and on all speakers are secure and that the wires
for each connection do not touch anything other than
their respective connections.
14
This unit has been exposed to a strong
external electric shock (such as lightning or
strong static electricity).
—
Set this unit to the standby mode, disconnect the power
cable, plug it back in after 30 seconds and then use this
unit normally.
Incorrect input or output cable connections. Connect the cables properly. If the problem persists,
the cables may be defective.
20-26
The optimizer microphone is connected.
Disconnect the optimizer microphone.
36
Audio input jack select is set to “HDMI”,
“COAX/OPT” or “ANALOG”.
Set Audio input jack select to “AUTO”.
44
Audio input jack select is set to
“ANALOG” while playing a source
encoded in Dolby Digital or DTS.
Set Audio input jack select to “AUTO” or
“COAX/OPT”.
44
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or the input selector
buttons on the remote control).
42, 43
Speaker connections are not secure.
Secure the connections.
14
The front speakers to be used have not been
selected properly.
Select the front speakers by pressing ASPEAKERS
on the front panel repeatedly.
43
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press JMUTE or NVOLUME +/– on the remote
control to resume audio output and then adjust the
volume.
45
Signals this unit cannot reproduce are
being input from a source component, such
as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
The HDMI components connected to this
unit do not support the HDCP copy
protection standards.
Connect HDMI components that support the HDCP
copy protection standards.
18
“S.AUDIO” is set to “OTHER” and
“HDMI” audio signals are not being played
back on this unit.
Set “S.AUDIO” to “HTR-6160” in “MANUAL
SETUP”.
98
The output and input for the picture are
Set “VIDEO CONV.” to “ON” or connect your source
connected to different types of video jacks. components in the same way as you connect your
video monitor to this unit.
97
Non-standard video signals are input.
The sound suddenly
goes off.
Sound is heard from
the speaker on one
side only.
110 En
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker impedance setting is correct.
28, 106
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned this unit off.
Turn this unit on, and play the source again.
—
The sound is muted.
Press JMUTE or NVOLUME +/– on the remote
control to resume audio output.
45
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
14
Incorrect settings in “SP LEVEL”.
Adjust the “SP LEVEL” settings.
87
Troubleshooting
Problem
Cause
Remedy
See
page
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
sound field program, the source signal is
directed to the center channel, and the front
and surround speakers output effect
sounds.
No sound is heard
from the center
speaker.
“CENTER SP” in “SET MENU” is set to
“NONE”.
Set “CENTER SP” to “SMALL” or “LARGE”.
86
One of the sound field programs (except
for “7ch Stereo”) has been selected.
Try another sound field program.
48
Press OSTRAIGHT to turn them on.
51
Try another sound field program.
42
“EXTRA SP ASSIGN” is set to a setting
other than “PRESENCE”.
Set “EXTRA SP ASSIGN” to “PRESENCE”.
85
No sound is heard
from the surround
speakers.
“SUR. L/R SP” in “SET MENU” is set to
“NONE”.
Set “SUR. L/R SP” to “SML” or “LRG”.
86
This unit is in the “STRAIGHT” mode and
a monaural source is being played back.
Press OSTRAIGHT on the front panel so that
“STRAIGHT” disappears from the front panel display.
51
No sound is heard
from the surround
back speakers.
“SUR. L/R SP” in “SET MENU” is set to
“NONE” and “SUR.B L/R SP” is
automatically set to “NONE”.
Set “SUR. L/R SP” and “SUR.B L/R SP” to a setting
other than “NONE”.
86
“SUR.B L/R SP” in “SET MENU” is set to
“NONE”.
Set “SUR.B L/R SP” to a setting other than “NONE”.
86
Zone 2 speaker
settings are not
available in “SET
MENU”.
“EXTRA SP ASSIGN” is set to a setting
other than “ZONE2”.
Set “EXTRA SP ASSIGN” to “ZONE2”.
85
FRONT B speakers
cannot be activated.
“EXTRA SP ASSIGN” is set to a setting
other than “FRONT B”.
Set “EXTRA SP ASSIGN” to “FRONT B”.
85
No sound from the
center, surround or
surround back
speakers when the
FRONT B speakers are
activated.
“EXTRA SP ASSIGN” is set to
“ZONE B”.
Set “EXTRA SP ASSIGN” to “FRONT B”.
85
Presence speaker
settings are not
available in “SET
MENU”.
“EXTRA SP ASSIGN” is set to a setting
other than “PRESENCE”.
Set “EXTRA SP ASSIGN” to “PRESENCE”.
85
No sound is heard
from the subwoofer.
“LFE/BASS OUT” in “SET MENU” is set
to “FRONT” when a Dolby Digital or DTS
signal is being played.
Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
85
“LFE/BASS OUT” in “SET MENU” is set
to “SWFR” or “FRONT” when a
2-channel source is being played.
Set “LFE/BASS OUT” to “BOTH”.
85
ADDITIONAL
INFORMATION
The sound field programs are turned off.
You are using a source or program
combination that does not output sound
from all channels.
No sound is heard
from the presence
speakers.
The source does not contain low-frequency
signals.
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in the
front panel display
does not light up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
—
Audio input jack select is set to
“ANALOG”.
Set Audio input jack select to “AUTO”.
44
A humming sound is
heard.
Incorrect cable connections.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
—
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the AUDIO
Turn on the power of the component.
OUT (REC) jacks of this unit is turned off.
The sound effects
cannot be recorded.
It is not possible to record the sound effects
with a recording component.
—
English
111 En
Troubleshooting
Problem
Cause
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT jack.
The source component is not connected to
the DIGITAL INPUT jacks of this unit.
Remedy
Connect the source component to the DIGITAL
INPUT jacks.
See
page
21, 23
Some components cannot record Dolby
Digital or DTS sources.
A source cannot be
recorded by an analog
component connected
to the AUDIO OUT
(REC) jacks.
The source component is not connected to
the analog AUDIO IN jacks of this unit.
The sound field
parameters and some
other settings of this
unit cannot be
changed.
Connect the source component to the analog AUDIO
IN jacks.
23
“MEMORY GUARD” in “SET MENU” is
set to “ON”.
Set “MEMORY GUARD” to “OFF”.
97
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
—
No sound is heard
from the connected
HDMI component.
The HDMI component does not accept the
multi-channel audio signals.
Convert the multi-channel audio signals to the
2-channel audio signals at the source component such
as a DVD player.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
14
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to the digital or highfrequency equipment.
Move this unit further away from such equipment.
—
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This unit suddenly
enters the standby
mode.
The internal temperature is too high and the
overheat protection circuitry has been
activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
XM Satellite Radio and SIRIUS Satellite
Radio signals are not output at the AUDIO
OUT (REC) jacks.
■ HDMI
Problem
No picture or sound.
112 En
Cause
Remedy
See
page
The number of the connected HDMI
components is over the limit.
Reduce the number of the connected HDMI
components.
—
HDCP authentication failed.
Check that the connected HDMI components support
the HDCP copy protection standards.
—
Troubleshooting
■ Tuner (FM/AM)
Problem
FM stereo reception is
noisy.
FM
AM
Cause
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Remedy
See
page
Check the antenna connections.
27
Try using a high-quality directional FM
antenna.
—
Use the manual tuning method.
53
There is distortion, and
There is multi-path interference.
clear reception cannot be
obtained even with a
good FM antenna.
Adjust the antenna position to eliminate multipath interference.
—
The desired station
cannot be tuned into with
the automatic tuning
method.
The signal is too weak.
Use a high-quality directional FM antenna.
—
Use the manual tuning method.
53
Previously preset
stations can no longer be
tuned into.
This unit has been disconnected for a
long period.
Preset the stations again.
54
The desired station
cannot be tuned into with
the automatic tuning
method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections and
orient the antenna for the best reception.
—
Use the manual tuning method.
53
There are continuous
crackling and hissing
noises.
Noise can result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
—
There are buzzing and
whining noises.
A TV set is being used nearby.
Move this unit away from the TV set.
—
ADDITIONAL
INFORMATION
English
113 En
Troubleshooting
■ XM Satellite Radio
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel
display. In this case, read the cause and follow the corresponding remedies.
Status message
See
page
Cause
Remedy
CHECK XM TUNER
The XM Mini-Tuner is not installed in the
XM Mini-Tuner Dock or the XM MiniTuner dock is not connected to this unit.
Confirm the XM Mini-Tuner is fully seated in the dock
and check the XM Mini-Tuner dock cable is connected
to this unit.
57, 61
CHECK ANTENNA
The XM antenna is not connected to the
XM Mini-Tuner Dock or the XM antenna
cable has become damaged.
Check that the XM antenna is securely connected to
the XM Mini-Tuner Dock and check the antenna cable
for damage. Replace the XM antenna if the cable is
damaged.
57
LOADING
The XM Mini-Tuner is acquiring audio or
program information from the XM satellite
signal. This message can also occur in
weak XM signal conditions. Note that this
unit may not respond to some operations
while this message is displayed.
This message should disappear in a few seconds in
good signal conditions. If you see this message often,
reposition the XM antenna to get better signal
reception. Use the “ANTENNA INFO” information in
the front panel or “XM Information” screen in the
video monitor to check the antenna reception level.
61
NO SIGNAL
The XM Mini-Tuner is not receiving the
XM satellite signal. Something may be
blocking the XM antenna’s view of the
satellites or the antenna is not properly
aimed.
Check for antenna obstructions and reposition the XM
antenna to get better signal reception. Use the
“ANTENNA INFO” information in the front panel or
“XM Information” screen in the video monitor to
check the antenna reception level. See instructions
supplied with the XM Mini-Tuner and Dock for
antenna installation information.
57
OFF AIR
The XM channel you selected is not
currently broadcasting.
Check back at a later time; in the mean time, select
another channel.
—
CH UNAUTH
You may be attempting to tune to an XM
channel that is blocked or that you cannot
receive with your XM subscription
package.
Consult the latest channel guide at
http://www.xmradio.com/ (US residents) and
http://www.xmradio.ca/ (Canadian residents) for the
current list of channels. For information on receiving
this channel, visit http://www.xmradio.com/ (US
residents) and http://www.xmradio.ca/ (Canadian
residents) or contact XM Satellite Radio at
1-800-967-2346 (US residents) and 1-877-438-9677
(Canadian residents).
58
CH UNAVAIL
The selected channel is not available. The
channel may have been reassigned to a
different channel number. This message
may occur initially with a new XM MiniTuner or an XM Mini-Tuner that has not
received XM’s signal for an extended
period.
Consult the latest channel guide at
http://www.xmradio.com/ (US residents) and
http://www.xmradio.ca/ (Canadian residents) for the
current list of channels. For cases of a new XM MiniTuner or an XM Mini-Tuner that has not received
XM’s signal for an extended period, allow the XM
Mini-Tuner to receive the XM satellite signal for at
least 5 minutes and then try to select the channel again.
—
- - - -
No artist name or song title is available for
this selection.
No action required.
—
114 En
Troubleshooting
■ SIRIUS Satellite Radio
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel
display. In this case, read the cause and follow the corresponding remedies.
Status message
Cause
Remedy
See
page
ANTENNA ERROR
The antenna is not connected to the
SiriusConnect tuner properly.
Check the connection of the antenna and
SiriusConnect tuner.
62
CHECK SR TUNER
The SiriusConnect tuner is not connected
to the SIRIUS jack of this unit correctly.
Check the connection of the SiriusConnect tuner and
this unit.
62
The SiriusConnect tuner is not connected
to the AC wall outlet.
Connect the power cable of the SiriusConnect tuner to
the AC wall outlet.
62
NOT SUPPORTED
This unit does not support the connected
SIRIUS Satellite Radio tuner.
Connect the SiriusConnect tuner that this unit
supports,
62
ACQUIRING
The signal is too weak.
Adjust the orientation of the antenna of the
SiriusConnect tuner. Use the “ANTENNA INFO”
information in the front panel display or “SIRIUS
Information” screen in the video monitor to check the
antenna reception level.
UPDATING
The SiriusConnect tuner is updating the
channel list.
Wait until the updating is complete.
—
The period of the subscription is end.
Contact SIRIUS Satellite Radio to renew the
subscription.
63
F/W UPDATING
The SiriusConnect tuner is updating the
firmware.
Wait until the updating is complete.
—
CALL SIRIUS
(CALL 888-539SIRIUS TO
SUBSCRIBE)
The selected channel is not subscribed.
Contact SIRIUS Satellite Radio to subscribe the
selected channel.
URL: https://activate.siriusradio.com/
Phone: 1-888-539-SIRIUS (1-888-539-7474)
63
Select another channel.
63
SUB UPDATED
INVALID
The subscription information is updated.
Select another channel.
63
Not Available
The operation you made is not available.
The selected channel is currently out of
service.
62, 67
Problem
The remote control
does not work nor
function properly.
Cause
Remedy
See
page
Wrong distance or angle.
The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
31
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
4
The remote control code is not correctly
set.
Set the remote control code correctly using “List of
remote control codes” at the end of this manual.
102
Try setting another code for the same manufacturer
using “List of remote control codes” at the end of this
manual.
102
English
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
ADDITIONAL
INFORMATION
■ Remote control
115 En
Troubleshooting
■ iPod
Note
In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection to your iPod
(see page 25).
Status message
Loading...
Cause
Remedy
See
page
This unit is in the middle of recognizing the
connection with your iPod.
This unit is in the middle of acquiring song
lists from your iPod.
Connect error
There is a problem with the signal path
from your iPod to this unit.
Unknown iPod
The iPod being used is not supported by
this unit.
iPod connected
Your iPod is properly stationed in a
Yamaha iPod universal dock (such as YDS10, sold separately) connected to the
DOCK terminal of this unit, and the
connection between your iPod and this unit
is complete.
Disconnected
Unable to play
Turn off this unit and reconnect the Yamaha iPod
universal dock to the DOCK terminal of this unit.
25
Try resetting your iPod.
—
Only iPod (Click and Wheel), iPod nano, and iPod
mini are supported.
—
Your iPod was removed from a Yamaha
iPod universal dock (such as YDS-10 sold
separately) connected to the DOCK
terminal of this unit.
Station your iPod back in a Yamaha iPod universal
dock (such as YDS-10 sold separately) connected to
the DOCK terminal of this unit.
25
This unit cannot play back the songs
currently stored on your iPod.
Check that the songs currently stored on your iPod are
playable.
—
Store some other playable music files on your iPod.
—
■ Bluetooth
Status message
Searching...
Cause
Remedy
See
page
The Bluetooth adapter and the Bluetooth
component is in the middle of the pairing.
The Bluetooth adapter and the Bluetooth
component is in the middle of establishing
the connection.
Completed
Canceled
BT connected
The paring is completed.
Disconnected
The Bluetooth component is disconnected
from the Yamaha Bluetooth adapter (such
as YBA-10, sold separately).
No BT adapter
The Bluetooth adapter is not connected to
the DOCK terminal.
Connect the Yamaha Bluetooth adapter (such as YBA10, sold separately) to the DOCK terminal.
25
BT Error
This unit detects a problem of the
connected Bluetooth adapter.
Set this unit to the standby mode and then turn on
again.
—
116 En
The paring is canceled.
The connection between the Yamaha
Bluetooth adapter (such as YBA-10, sold
separately) and the Bluetooth component is
established.
Troubleshooting
■ AUTO SETUP
Before AUTO SETUP
Error message
Cause
Remedy
See
page
Connect MIC!
Optimizer microphone is not connected.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
32
Unplug HP!
Memory Guard!
Headphones are connected.
Unplug the headphones.
—
The parameters of this unit are protected.
Set “MEMORY GUARD” to “OFF”.
97
During AUTO SETUP
Error message
Cause
E-1:NO FRONT SP
E-2:NO SUR SP
E-3:NO PRNS SP
E-4:SBR->SBL
Front L/R channel signals are not detected.
E-5:NOISY
Remedy
See
page
Check the front L/R speaker connections.
14
A surround channel signal is not detected.
Check the surround speaker connections.
14
A presence channel signal is not detected.
Check the presence speaker connections.
14
Only a right surround back channel signal is
detected.
Connect the surround back speaker to the
LEFT SURROUND BACK SPEAKERS
terminal if you only have one surround back
speaker.
14
Background noise is too loud.
Try running “AUTO SETUP” in a quiet
environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the
optimizer microphone.
—
Surround back speakers are connected,
though surround L/R speakers are not.
Connect surround speakers when you use
surround back speakers.
14
E-7:NO MIC
The optimizer microphone was unplugged
during the “AUTO SETUP” procedure.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
32
E-8:NO SIGNAL
The optimizer microphone does not detect
test tones.
Check the microphone setting.
32
Check the speaker connections and
placement.
14
E-9:USER CANCEL
The “AUTO SETUP” procedure was
cancelled due to user activity.
Run “AUTO SETUP” again.
32
E-10:INTERNAL ERROR
An internal error occurred.
Run “AUTO SETUP” again.
32
ADDITIONAL
INFORMATION
E-6:CHECK SUR.
English
117 En
Troubleshooting
After AUTO SETUP
Warning message
Cause
Remedy
See
page
W-1:OUT OF PHASE
Speaker polarity is not correct. This message
may appear depending on the speakers even
when the speakers are connected correctly.
Check the speaker connections for proper
polarity (+ or –).
14
W-2:OVER 24m (80ft)
The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker closer to the listening
position.
—
W-3:LEVEL ERROR
The difference of volume level among
speakers is excessive.
Readjust the speaker installation so that all
speakers are set in locations with similar
conditions.
—
W-4:CHECK PRNS
“EXTRA SP ASSIGN” is set to
“PRESENCE”, though the presence channel
signals are not detected.
Check the speaker connections.
14
Use speakers of similar quality.
—
When “SWFR: TOO LOUD”or “SWFR:
TOO LOW” appears in the result screen, the
output volume of the subwoofer.
32
Check the presence speaker connections.
14
Set “EXTRA SP ASSIGN” to a setting other
than “PRESENCE”.
33
Notes
• If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.
• If a warning message “W-1”, “W-2” or “W-3” appears, corrections are made, but they may not be optimal.
• If an error message “E-10” occurs repeatedly, contact a qualified Yamaha service center.
118 En
RESETTING THE SYSTEM
Resetting the system
Use this feature to reset all the parameters of this unit to the initial factory settings.
Notes
• This procedure completely resets all the parameters of this unit including the “SET MENU” parameters. However, the advanced setup
menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on this unit.
y
To cancel the initialization procedure at any time without making any changes, press LSYSTEM OFF on the front panel.
1
Press LSYSTEM OFF on the front panel to
set this unit to the standby mode.
2
Press and hold MTONE CONTROL and
then press KMAIN ZONE ON/OFF to turn
on this unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
TONE CONTROL
While holding
down
MAIN ZONE
ON/OFF
3
Rotate the NPROGRAM selector to select
“INIT”.
4
Press MTONE CONTROL repeatedly to
select “ALL”.
ADDITIONAL
INFORMATION
y
Select “CANCEL” to cancel the initialization procedure
without making any changes.
5
Press L SYSTEM OFF to confirm your
selection and set this unit to the standby
mode.
English
119 En
GLOSSARY
Glossary
■ Audio and video synchronization
(lip sync)
Lip sync, an abbreviation for lip synchronization, is a technical
term that involves both a problem and a capability of maintaining
audio and video signals synchronized during post-production and
transmission. Whereas the audio and video latency requires
complex end-user adjustments, HDMI version 1.3 incorporates an
automatic audio and video syncing capability that allows devices
to perform this synchronization automatically and accurately
without user interaction.
■ Bi-amplification connection
A bi-amplification connection uses two amplifiers for a speaker.
One amplifier is connected to the woofer section of a loudspeaker
while the other is connected to the combined mid and tweeter
section. With this arrangement each amplifier operates over a
restricted frequency range. This restricted range presents each
amplifier with a much simpler job and each amplifier is less likely
to influence the sound in some way. The internal crossover of the
speaker consists of a LPF (low pass filter) and a HPF (high pass
filter). As its name implies, the LPF passes frequencies below a
cutoff and rejects frequencies above the cutoff frequency.
Likewise, the HPF passes frequencies above its cutoff.
■ Component video signal
With the component video signal system, the video signal is
separated into the Y signal for the luminance and the PB and PR
signals for the chrominance. Color can be reproduced more
faithfully with this system because each of these signals is
independent. The component signal is also called the “color
difference signal” because the luminance signal is subtracted
from the color signal. A monitor with component input jacks is
required in order to output component signals.
■ Composite video signal
With the composite video signal system, the video signal is
composed of three basic elements of a video picture: color,
brightness and synchronization data. A composite video jack on a
video component transmits these three elements combined.
■ Deep Color
Deep Color refers to the use of various color depths in displays,
up from the 24-bit depths in previous versions of the HDMI
specification. This extra bit depth allows HDTVs and other
displays go from millions of colors to billions of colors and
eliminate on-screen color banding for smooth tonal transitions
and subtle gradations between colors. The increased contrast ratio
can represent many times more shades of gray between black and
white. Also Deep Color increases the number of available colors
within the boundaries defined by the RGB or YCbCr color space.
■ Dolby Digital
Dolby Digital is a digital surround sound system that gives you
completely independent multi-channel audio. With 3 front
channels (front L/R and center), and 2 surround stereo channels,
Dolby Digital provides 5 full-range audio channels. With an
additional channel especially for bass effects, called LFE (Low
Frequency Effect), the system has a total of 5.1-channels (LFE is
counted as 0.1 channel). By using 2-channel stereo for the
surround speakers, more accurate moving sound effects and
surround sound environment are possible than with Dolby
Surround. The wide dynamic range from maximum to minimum
volume reproduced by the 5 full-range channels and the precise
sound orientation generated using digital sound processing
provide listeners with unprecedented excitement and realism.
With this unit, any sound environment from monaural up to a 5.1channel configuration can be freely selected for your enjoyment.
■ Dolby Digital EX
Dolby Digital EX creates 6 full-bandwidth output channels from
5.1-channel sources. This is done using a matrix decoder that
derives 3 surround channels from the 2 in the original recording.
For the best results, Dolby Digital EX should be used with movie
sound tracks recorded with Dolby Digital Surround EX. With this
additional channel, you can experience more dynamic and
realistic moving sound especially with scenes with
“fly-over” and “fly-around” effects.
■ Dolby Digital Plus
Dolby Digital Plus is an advanced audio technology developed
for high-definition programming and media including HD
broadcasts, HD DVD, and Blu-ray Disc. Selected as a mandatory
audio standard for HD DVD and as an optional audio standard for
Blu-ray Disc, this technology delivers multichannel sound with
discrete channel output. Supporting bitrates up to 6.0 Mbps,
Dolby Digital Plus can carry up to 7.1 discreet audio channels
simultaneously. Supported by HDMI version 1.3 and designed for
the optical disc players and AV receivers/amplifiers of the future,
Dolby Digital Plus also remains fully compatible with the
existing multichannel audio systems that incorporate Dolby
Digital.
■ Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to decode vast
numbers of existing Dolby Surround sources. This new
technology enables a discrete 5-channel playback with 2 front left
and right channels, 1 center channel, and 2 surround left and right
channels instead of only 1 surround channel for conventional Pro
Logic technology. There are three modes available: “Music
mode” for music sources, “Movie mode” for movie sources and
“Game mode” for game sources.
■ Dolby Pro Logic IIx
Dolby Pro Logic IIx is a new technology enabling discrete multichannel playback from 2-channel or multi-channel sources. There
are three modes available: “Music mode” for music sources,
“Movie mode” for movie sources (for 2-channel sources only)
and “Game mode” for game sources.
120 En
Glossary
■ Dolby Surround
■ DTS Express
Dolby Surround uses a 4-channel analog recording system to
reproduce realistic and dynamic sound effects: 2 front left and
right channels (stereo), a center channel for dialog (monaural),
and a surround channel for special sound effects (monaural). The
surround channel reproduces sound within a narrow frequency
range. Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as well. The
Dolby Pro Logic decoder built into this unit employs a digital
signal processing system that automatically stabilizes the volume
on each channel to enhance moving sound effects and
directionality.
DTS Express is an advanced audio technology for the optional
feature on Blu-ray Disc or HD DVD, which offers high-quality,
low bit rate audio optimized for network streaming, and Internet
applications. DTS Express is used for the Secondary Audio
feature of Blu-ray Disc or the Sub Audio feature of HD DVD.
These features deliver audio commentaries (for example, the
additional commentaries made by the director of a film) on
demand by the users via the Internet, etc. DTS Express signals are
mixed down with the main audio stream on the player
component, and the component sends the mixed audio stream to
the AV receivers/amplifiers via digital coaxial, digital optical, or
analog connections.
■ Dolby TrueHD
Dolby TrueHD is an advanced lossless audio technology
developed for high-definition disc-based media including HD
DVD and Blu-ray Disc. Selected as a mandatory audio standard
for HD DVD and as an optional audio standard for Blu-ray Disc,
this technology delivers sound that is bit-for-bit identical to the
studio master, offering a high-definition home theater experience.
Supporting bitrates up to 18.0 Mbps, Dolby TrueHD can carry up
to 8 discrete channels of 24-bit/96 kHz audio simultaneously.
Supported by HDMI version 1.3 and designed for the optical disc
players and AV receivers/amplifiers of the future, Dolby TrueHD
also remains fully compatible with the existing multichannel
audio systems and retains the metadata capability of Dolby
Digital, allowing dialog normalization and dynamic range
control.
■ DSD
Direct Stream Digital (DSD) technology stores audio signals on
digital storage media, such as Super Audio CDs. Using DSD,
signals are stored as single bit values at a high-frequency
sampling rate of 2.8224 MHz, while noise shaping and
oversampling are used to reduce distortion, a common occurrence
with very high quantization of audio signals. Due to the high
sampling rate, better audio quality can be achieved than that
offered by the PCM format used for normal audio CDs.
DTS 96/24 offers an unprecedented level of audio quality for
multi-channel sound on DVD video, and is fully backwardcompatible with all DTS decoders. “96” refers to a 96 kHz
sampling rate compared to the typical 48 kHz sampling rate. “24”
refers to 24-bit word length. DTS 96/24 offers sound quality
transparent to the original 96/24 master, and 96/24 5.1-channel
sound with full-quality full-motion video for music programs and
motion picture soundtracks on DVD video.
■ DTS Digital Surround
■ DTS-HD Master Audio
DTS-HD Master Audio is an advanced lossless audio technology
developed for high-definition disc-based media including HD
DVD and Blu-ray Disc. Selected as a mandatory audio standard
for both HD DVD and Blu-ray Disc, this technology delivers
sound that is bit-for-bit identical to the studio master, offering a
high-definition home theater experience. Supporting bitrates up to
18.0 Mbps for HD DVD and up to 24.5 Mbps for Blu-ray Disc,
DTS-HD Master Audio can carry up to 7.1 discrete channels of
24-bit/96 kHz audio simultaneously. Supported by HDMI version
1.3 and designed for the optical disc players and AV receivers/
amplifiers of the future, DTS-HD Master Audio also remains
fully compatible with the existing multichannel audio systems
that incorporate DTS Digital Surround.
■ HDMI
HDMI (High-Definition Multimedia Interface) is the first
industry-supported, uncompressed, all-digital audio/video
interface. Providing an interface between any source (such as a
set-top box or AV receiver) and an audio/video monitor (such as a
digital television), HDMI supports standard, enhanced or highdefinition video as well as multi-channel digital audio using a
single cable. HDMI transmits all ATSC HDTV standards and
supports 8-channel digital audio, with bandwidth to spare to
accommodate future enhancements and requirements.
When used in combination with HDCP (High-bandwidth Digital
Content Protection), HDMI provides a secure audio/video
interface that meets the security requirements of content
providers and system operators. For further information on
HDMI, visit the HDMI website at
“http://www.hdmi.org/”.
121 En
English
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6.1-channel digital sound track, and
is now rapidly gaining popularity in movie theaters around the
world. DTS, Inc. has developed a home theater system so that you
can enjoy the depth of sound and natural spatial representation of
DTS digital surround in your home. This system produces
practically distortion-free 6.1-channel sound (technically, front
left and right, center, surround left and right, and LFE 0.1
(subwoofer) channels for a total of 5.1 channels). This unit
incorporates a DTS-ES decoder that enables 6.1-channel
reproduction by adding the surround back channel to the existing
5.1-channel format.
DTS-HD High Resolution Audio is an high resolution audio
technology developed for high-definition disc-based media
including HD DVD and Blu-ray Disc. Selected as an optional
audio standard for both HD DVD and Blu-ray Disc, this
technology delivers sound that is virtually indistinguishable from
the original, offering a high-definition home theater experience.
Supporting bitrates up to 3.0 Mbps for HD DVD and 6.0 Mbps
for Blu-ray Disc, DTS-HD High Resolution Audio can carry up
to 7.1 discrete channels of 24-bit/96 kHz audio simultaneously.
Supported by HDMI version 1.3 and designed for the optical disc
players and AV receivers/amplifiers of the future, DTS-HD High
Resolution Audio also remains fully compatible with the existing
multichannel audio systems that incorporate DTS Digital
Surround.
ADDITIONAL
INFORMATION
■ DTS 96/24
■ DTS-HD High Resolution Audio
Glossary
■ LFE 0.1 channel
This channel reproduces low-frequency signals. The frequency
range of this channel is from 20 Hz to 120 Hz. This channel is
counted as 0.1 because it only enforces a low-frequency range
compared to the full-range reproduced by the other 5/6 channels
in Dolby Digital or DTS 5.1/6.1-channel systems.
■ Neo:6
Neo:6 decodes the conventional 2-channel sources for 6- channel
playback by the specific decoder. It enables playback with the
full-range channels with higher separation just like digital
discrete signal playback. There are two modes available: “Music
mode” for music sources and “Cinema mode” for movie sources.
■ Neural Surround
Neural Surround™ represents the latest advancement in surround
technology and has been adopted by XM Satellite Radio for
digital radio broadcast of surround recordings and live events in
surround sound. Neural Surround™ employs psychoacoustic
frequency domain processing which allows delivery of a more
detailed sound stage with superior channel separation and
localization of audio elements. System playback is scalable from
5.1 to 7.1 multi-channel surround playback.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog audio
signal is digitized, recorded and transmitted without using any
compression. This is used as a method of recording CDs and
DVD audio. The PCM system uses a technique for sampling the
size of the analog signal per very small unit of time. Standing for
“Pulse Code Modulation”, the analog signal is encoded as pulses
and then modulated for recording.
■ Sampling frequency and number of
quantized bits
When digitizing an analog audio signal, the number of times the
signal is sampled per second is called the sampling frequency,
while the degree of fineness when converting the sound level into
a numeric value is called the number of quantized bits. The range
of rates that can be played back is determined based on the
sampling rate, while the dynamic range representing the sound
level difference is determined by the number of quantized bits. In
principle, the higher the sampling frequency, the wider the range
of frequencies that can be played back, and the higher the number
of quantized bits, the more finely the sound level can be
reproduced.
■ S-video signal
With the S-video signal system, the video signal normally
transmitted using a pin cable is separated and transmitted as the Y
signal for the luminance and the C signal for the chrominance
through the S-video cable. Using the S VIDEO jack eliminates
video signal transmission loss and allows recording and playback
of even more beautiful images.
■ x.v.Color
A color space standard supported by HDMI version 1.3. It is a
more extensive color space than sRGB, and allows the expression
of colors that could not be expressed before. While remaining
compatible with the color gamut of sRGB standards, “x.v.Color”
expands the color space and can thus produce more vivid, natural
images. It is particularly effective for still pictures and computer
graphics.
122 En
SOUND FIELD PROGRAM INFORMATION
Sound field program information
■ Elements of a sound field
■ SILENT CINEMA
What really creates the rich, full tones of a live instrument
are the multiple reflections from the walls of the room. In
addition to making the sound live, these reflections enable
us to tell where the player is situated as well as the size
and shape of the room in which we are sitting.
There are two distinct types of sound reflections that
combine to make up the sound field in addition to the
direct sound coming straight to our ears from the player’s
instrument.
Yamaha has developed a natural, realistic sound effect
DSP algorithm for headphones. Parameters for
headphones have been set for each sound field so that
accurate representations of all the sound field programs
can be enjoyed on headphones.
Early reflections
Reflected sounds reach our ears extremely rapidly (50 ms
to 100 ms after the direct sound), after reflecting from one
surface only (for example, from a wall or the ceiling).
Early reflections actually add clarity to the direct sound.
Reverberations
These are caused by reflections from more than one
surface (for example, from the walls, and the ceiling) so
numerous that they merge together to form a continuous
sonic afterglow. They are non-directional and lessen the
clarity of the direct sound.
■ Virtual CINEMA DSP
Yamaha has developed a Virtual CINEMA DSP algorithm
that allows you to enjoy DSP sound field surround effects
even without any surround speakers by using virtual
surround speakers. It is even possible to enjoy Virtual
CINEMA DSP using a minimal two-speaker system that
does not include a center speaker.
■ Compressed Music Enhancer
The Compressed Music Enhancer feature of this unit
enhances your listening experience by regenerating the
missing harmonics in a compression artifact. As a result,
flattened complexity due to the loss of high-frequency
fidelity as well as lack of bass due to the loss of lowfrequency bass is compensated, providing improved
performance of the overall sound system.
Direct sound, early reflections and subsequent
reverberations taken together help us to determine the
subjective size and shape of the room, and it is this
information that the digital sound field processor
reproduces in order to create sound fields.
ADDITIONAL
INFORMATION
If you could create the appropriate early reflections and
subsequent reverberations in your listening room, you
would be able to create your own listening environment.
The acoustics in your room could be changed to those of a
concert hall, a dance floor, or a room with virtually any
size at all. This ability to create sound fields at will is
exactly what Yamaha has done with the digital sound field
processor.
■ CINEMA DSP
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers designed for
acoustic effects. Since home conditions, such as room
size, wall material, number of speakers, and so on, can
differ so widely, it is inevitable that there are differences in
the sound heard. Based on a wealth of actually measured
data, Yamaha CINEMA DSP uses Yamaha original sound
field technology to combine Dolby Pro Logic, Dolby
Digital and DTS systems to provide the audiovisual
experience of a movie theater in the listening room of your
own home.
English
123 En
SPECIFICATIONS
Specifications
AUDIO SECTION
• Volume Control ....................................... MUTE/–80 dB to 16.5 dB
• Minimum RMS Output Power for Front, Center, Surround,
Surround back
1 kHz, 0.7% THD, 8 Ω ...................................................... 110 W
• Tone Control (Front L/R)
BASS Boost/Cut ..................................................... ±10 dB/50 Hz
BASS Turnover Frequency ................................................. 350 Hz
TREBLE Boost/Cut .............................................. ±10 dB/20 kHz
TREBLE Turnover Frequency ........................................... 3.5 kHz
• Dynamic Power (IHF)
Front L/R, 8/6/4/2 Ω ..................................... 135/165/195/240 W
• Maximum Output Power [Russia model]
Speaker impedance setting: 8 Ω, 1 kHz, 0.7% THD, 4 Ω
.......................................................................................... 145 W
• Dynamic Headroom [U.S.A. and Canada models]
8 Ω ....................................................................................... 1.4 dB
• IEC Output Power [Russia model]
Front L/R, 1 kHz, 0.06% THD, 8 Ω ................................... 105 W
• Damping Factor (IHF)
Front L/R, SPEAKERS A, 20 Hz to 20 kHz, 8 Ω
.................................................................................. 120 or more
• Input Sensitivity/Input Impedance
CD, etc. ................................................................. 200 mV/47 kΩ
MULTI CH INPUT ............................................... 200 mV/47 kΩ
• Maximum Input Voltage
CD, etc.
Effect On, 1 kHz, 0.5% THD ............................... 2.3 V or more
• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F.
(FRONT SP, CENTER SP, SUR. L/R SP, SUR.B L/R SP:
SMALL/SML) ............................................................ 12 dB/oct.
L.P.F. (Subwoofer) ......................................................... 24 dB/oct.
VIDEO SECTION
• Video Format (Gray Back)
[U.S.A. and Canada models] ............................................... NTSC
[Russia model] ........................................................................ PAL
• Video Format (Video Conversion) ................................. NTSC/PAL
• Signal Level
Composite ................................................................. 1 Vp-p/75 Ω
S-video ............................ 1 Vp-p/75 Ω (Y), 0.286 Vp-p/75 Ω (C)
Component ................... 1 Vp-p/75 Ω (Y), 0.7 Vp-p/75 Ω (PB/PR)
• Maximum Input Level (Video Conversion Off)
............................................................................... 1.5 Vp-p or more
• Rated Output Voltage/Output Impedance
OUT (REC) .......................................................... 200 mV/1.2 kΩ
PRE OUT ................................................................. 1.0 V/1.2 kΩ
SUBWOOFER (2ch Stereo, FRONT SP: SMALL)
................................................................................ 1.0 V/1.2 kΩ
ZONE 2 OUT ....................................................... 200 mV/1.2 kΩ
• Signal to Noise Ratio
.................................................................................... 50 dB or more
• Headphone Jack Rated Output/Impedance
CD, etc. (1 kHz, 50 mV, 8 Ω) ................................ 150 mV/100 Ω
FM SECTION
• Frequency Response
CD to Front L/R, 10 Hz to 100 kHz
...................................................................................... +0/–3 dB
• Total Harmonic Distortion
CD, etc. to Front L/R
2ch Stereo, 20 Hz to 20 kHz, 50 W, 8 Ω ............... 0.06% or less
• Signal to Noise Ratio (IHF-A Network)
CD, etc. (Effect Off, 250 mV) to Front L/R
............................................................................ 100 dB or more
• Frequency Response (MONITOR OUT)
Component (Video Conversion Off)
............................................................. 5 Hz to 100 MHz, –3 dB
• Tuning Range
[U.S.A. and Canada models] .......................... 87.5 to 107.9 MHz
[Russia model] ............................................ 87.50 to 108.00 MHz
• 50 dB Quieting Sensitivity (IHF)
1 kHz, 100% MOD., Mono .............................. 2.8 µV (20.2 dBf)
• Signal to Noise Ratio (IHF)
Mono/Stereo ............................................................. 73 dB/70 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo ......................................................................... 0.5%
• Antenna Input (unbalanced) ..................................................... 75 Ω
• Residual Noise (IHF-A Network)
Front L/R ................................................................ 150 µV or less
AM SECTION
• Channel Separation (1 kHz/10 kHz)
CD, etc. (5.1 kΩ shortened) to Front L/R
................................................................... 60 dB/45 dB or more
• Tuning Range
[U.S.A. and Canada models] .............................. 530 to 1710 kHz
[Russia model] .................................................... 531 to 1611 kHz
124 En
Specifications
GENERAL
• Power Supply
[U.S.A. and Canada models] ............................. AC 120 V, 60 Hz
[Russia model] ................................................... AC 230 V, 50 Hz
• Power Consumption
[U.S.A. and Canada models] ................................. 400 W/500 VA
[Russia model] .................................................................... 440 W
• Standby Power Consumption
[U.S.A. and Canada models] .................................... 0.8 W or less
[Russia model] .......................................................... 0.1 W or less
• AC Outlets
[U.S.A. and Canada models]
.......................................................... 2 (Total 100 W maximum)
[Russia model] ...................................... 2 (Total 50 W maximum)
• Dimensions (W x H x D) ................................ 435 x 171 x 393 mm
(17-1/8 x 6-3/4 x 15-1/2 in)
• Weight .............................................................. 11.8 kg (26 lbs 4 oz)
* Specifications are subject to change without notice.
ADDITIONAL
INFORMATION
English
125 En
INDEX
Index
■
Numerics
1 BASIC MENU, Manual setup .......... 80
2 VOLUME MENU, Manual setup ..... 81
2ch STEREO, Sound field program .... 50
3 SOUND MENU, Manual setup ........ 81
4 INPUT MENU, Manual setup .......... 82
5 OPTION MENU, Manual setup ....... 82
7ch Enhancer, Sound field program .... 50
7ch STEREO, Sound field program .... 50
96/24 indicator ..................................... 30
■
A
A)DISPLAY SET, Option menu ......... 96
A)EQUALIZER, Sound menu ............. 90
A)SPEAKER SET, Basic menu ........... 85
AC OUTLETS (SWITCHED) ............. 28
ACQUIRING, SIRIUS Satellite Radio
status message ............................... 115
Action Game, Sound field program ..... 49
ADAPTIVE DRC indicator ................. 30
ADAPTIVE DRC, Volume menu ....... 89
ADAPTIVE DSP LEVEL,
Volume menu .................................. 89
Adaptive DSP level, Volume menu ..... 89
Adaptive dynamic range control,
Volume menu .................................. 89
Advanced setup .................................. 106
Advanced sound configurations ........... 72
Adventure, Sound field program ......... 50
ALL CH SEARCH, SIRIUS tuning .... 64
ALL CH SEARCH, XM tuning ........... 59
All Channel Search mode,
SIRIUS tuning ................................. 64
All Channel Search mode,
XM tuning ....................................... 59
AM antenna connection ....................... 27
AM tuning ............................................ 53
Amplifier function OSD display time,
Display settings ............................... 96
ANTENNA ERROR, SIRIUS Satellite
Radio status message ..................... 115
Audio and video synchronization,
Sound menu ..................................... 92
Audio cable plugs ................................ 17
Audio components connection ............. 23
Audio information ................................ 46
Audio input jacks selection .................. 44
AUDIO jacks ....................................... 17
Audio jacks .......................................... 17
AUDIO SELECT ................................. 44
AUDIO SELECT,
Initial configuration ......................... 98
Audio select, Initial configuration ....... 98
Audio signal flow ................................. 19
Auto delay, Lip sync ............................ 92
AUTO SETUP ............................... 32, 80
Auto setup ............................................ 80
AUTO SETUP, Troubleshooting ....... 117
AUTO TUNING .................................. 53
AUTO, Lip sync .................................. 92
126 En
Automatic tuning mode,
FM/AM tuning .................................53
Available decoders with Sound field
programs ..........................................77
■
B
B)LFE LEVEL, Sound menu ...............91
B)SP LEVEL, Basic menu ...................87
B)VIDEO SET, Option menu ..............97
BASIC MENU, Manual setup .............85
Basic menu, Manual setup ...................80
Bass cross over, Speaker settings .........87
BGV, Input menu .................................95
BGV, Input menu, Multi-channel input
BGV, Input menu .............................95
BI-AMP, Advanced setup ..................109
Bi-Amplifier, Advanced setup ...........109
Bluetooth adapter connection ...............25
Bluetooth component playback ............70
Bluetooth component use .....................70
Bluetooth, Troubleshooting ...............116
BT connected,
Bluetooth status message ...............116
BT Error,
Bluetooth status message ...............116
■
C
C)DYNAMIC RANGE,
Sound menu .....................................91
C)MEMORY GUARD,
Option menu ....................................97
C)SP DISTANCE, Basic menu ............88
C. IMAGE, Decoder parameter ...........79
Cable plugs ...........................................17
CALL SIRIUS, SIRIUS Satellite Radio
status message ................................115
CAT SEARCH, SIRIUS tuning ...........64
CAT SEARCH, XM tuning .................59
Category Search mode,
SIRIUS tuning ..................................64
CD player connection ...........................23
Cellar Club,
Sound field program ........................49
CENTER PRE OUT jack
connection ........................................24
CENTER SP, Speaker settings .............86
Center speaker level, Sound field
parameter .........................................77
Center speaker, Speaker settings ..........86
CENTER WIDTH,
Decoder parameter ...........................79
CH UNAVAIL, XM Satellite Radio
status message ................................114
Chamber, Sound field program ............48
Charge on standby, Input menu ...........94
CHECK ANTENNA, XM Satellite Radio
status message ................................114
CHECK PRNS, Automatic setup
warning message ............................118
CHECK SR TUNER, SIRIUS Satellite
Radio status message ..................... 115
CHECK SUR., Automatic setup
error message ................................ 117
CHECK XM TUNER, XM Satellite Radio
status message ............................... 114
CINEMA DSP indicator ...................... 31
CLASSICAL,
Sound field category ....................... 48
Completed,
Bluetooth status message .............. 116
COMPONENT VIDEO jacks ............. 17
Compressed Music Enhancer .............. 50
Connect error,
iPod status message ....................... 116
Connect MIC!,
Automatic setup error message ..... 117
Connection,
AM antenna connection .................. 27
Connection, audio components ........... 23
Connection, Bluetooth adapter ............ 25
Connection, CD player ........................ 23
Connection,
CENTER PRE OUT jack ................ 24
Connection, DVD player ..................... 21
Connection, DVD recorder .................. 22
Connection, External amplifier ........... 24
Connection, external decoder .............. 25
Connection, FM antenna ..................... 27
Connection,
FRONT PRE OUT jacks ................. 24
Connection, iPod universal dock ......... 25
Connection, Multi-format player ......... 25
Connection, Power cable ..................... 28
Connection, projector .......................... 20
Connection, PVR ................................. 22
Connection, set-top boxes ................... 22
Connection, SiriusConnect tuner ......... 62
Connection, speaker cable ................... 16
Connection, SUBWOOFER PRE OUT
jack .................................................. 24
Connection,
SUR.BACK PRE OUT jacks .......... 24
Connection,
SURROUND PRE OUT jacks ........ 24
Connection, TV monitor ...................... 20
Connection, VCR ................................ 22
Connection, XM Mini-Tuner Dock ..... 57
Controlling a TV ............................... 100
Controlling other components,
Remote control .............................. 101
Controlling this unit,
Remote control .............................. 100
CROSS OVER, Speaker settings ........ 87
CT LEVEL, Sound field parameter ..... 77
Current status display .......................... 44
■
D
D)INIT. CONFIG, Option menu ......... 98
D)LIPSYNC, Sound menu .................. 92
Index
■
E
■
F
F)ZONE2 SET, Option menu ..............99
F/W UPDATING, SIRIUS Satellite Radio
status message ................................115
FL SCROLL, Display settings .............96
FM antenna ...........................................27
FM antenna connection ........................27
FM tuning .............................................53
Front input, Input menu ........................95
Front panel display ...............................30
Front panel display scroll,
Display settings ................................96
FRONT PRE OUT jack connection .....24
FRONT SP, Speaker settings ...............86
Front speaker set selection ...................43
Front speakers, Speaker settings ..........86
FRONT, Input menu ............................95
■
G
GEQ, Equalizer ....................................90
Graphic equalizer, Equalizer ................90
■
H
Hall in Munich,
Sound field program ........................48
Hall in Vienna,
Sound field program ........................48
HDCP ERROR,
HDMI error message ........................46
HDMI ...................................................18
HDMI AUTO, Lip sync .......................92
HDMI auto, Lip sync ...........................92
HDMI indicator ....................................30
HDMI set, Option menu .......................98
HDMI, troubleshooting ......................112
HEADPHONE, Dynamic range ...........91
HEADPHONE,
Low frequency effect level ..............91
Headphones ......................................... 45
Headphones indicator .......................... 30
Headphones, Dynamic range ............... 91
Headphones,
Low frequency effect level .............. 91
■
I
I/O ASSIGNMENT, Input menu ......... 93
Infrared window .................................. 31
INI.VOL., Audio settings .................... 89
INI.VOL., Zone 2 settings ................... 99
INIT, Advanced setup ....................... 109
INIT.DLY,
Sound field parameter ..................... 74
Initial configuration,
Option menu .................................... 98
Initial delay,
Sound field parameter ..................... 74
Initial volume, Audio settings ............. 89
INPUT CH, Input menu ...................... 95
Input channel and speaker
indicators ......................................... 31
Input channel indicators ...................... 31
Input channels, Input menu ................. 95
INPUT MENU, Manual setup ............. 93
Input menu, Manual setup ................... 82
INPUT RENAME, Input menu ........... 94
Input rename, Input menu .................... 94
Input signal indicators ......................... 30
Input source indicators ........................ 30
Input source information display ......... 46
Input/output assignment,
Input menu ....................................... 93
INTERNAL ERROR,
Automatic setup error message ..... 117
INVALID, SIRIUS Satellite Radio
status message ............................... 115
iPod universal dock connection ........... 25
iPod use ............................................... 68
iPod, Troubleshooting ....................... 116
■
J
Jacks .................................................... 17
■
L
LEVEL ERROR, Automatic setup
warning message ........................... 118
LFE/BASS OUT,
Speaker settings ............................... 85
LFE/Bass out, Speaker settings ........... 85
Lip Sync, Sound menu ........................ 92
LIVE/CLUB,
Sound field category ........................ 49
LIVENESS,
Sound field parameter ..................... 75
Liveness, Sound field parameter ......... 75
LOADING, XM Satellite Radio status
message ......................................... 114
Loading..., iPod status message ......... 116
Low-frequency effect level,
Sound menu ..................................... 91
LVL, Auto setup result ........................ 34
127 En
English
E)EXTD SUR., Sound menu ............... 92
E)HDMI SET, Option menu ................ 98
E-1:NO FRONT SP,
Automatic setup error message ...... 117
E-10:INTERNAL ERROR,
Automatic setup error message ...... 117
E-2:NO SUR SP, Automatic setup
error message ................................. 117
E-3:NO PRNS SP, Automatic setup
error message ................................. 117
E-4:SBR->SBL, Automatic setup
error message ................................. 117
E-5:NOISY, Automatic setup error
message .......................................... 117
E-6:CHECK SUR., Automatic setup error
message .......................................... 117
E-7:NO MIC, Automatic setup error
message .......................................... 117
E-8:NO SIGNAL, Automatic setup error
message .......................................... 117
E-9:USER CANCEL,
Automatic setup error message ......117
EFFECT LEVEL,
Sound field parameter ..........................77
ENHANCER indicator .........................30
ENTERTAINMENT,
Sound field category ........................49
EQ TYPE SELECT, Equalizer ............90
EQ, Auto setup parameter ....................33
Equalizer type select, Equalizer ...........90
Equalizer, Sound menu ........................90
EXTD SUR., Initial configuration .......98
Extended surround,
Initial configuration .........................98
Extended surround, Sound menu .........92
External amplifier connection ..............24
External decoder connection ................25
EXTRA SP ASSIGN, Auto setup
parameter ..........................................33
EXTRA SP ASSIGN,
Speaker settings ...............................85
Extra speaker assignment,
Auto setup parameter .......................33
Extra speaker assignment,
Speaker settings ...............................85
ADDITIONAL
INFORMATION
D)TEST TONE, Basic menu ............... 88
Decoder descriptions ............................ 78
Decoder indicators ............................... 30
DECODER MODE,
Initial configuration ......................... 98
Decoder mode,
Initial configuration ......................... 98
DECODER MODE,
Input menu ....................................... 94
Decoder mode, Input menu .................. 94
Decoder selection ................................. 78
DEVICE OVER,
HDMI error message ....................... 46
DIALG.LIFT,
Sound field parameter ...................... 73
Dialogue lift,
Sound field parameter ...................... 73
DIGITAL COAXIAL jacks ................. 17
DIGITAL OPTICAL jacks .................. 17
DIMENSION, Decoder parameter ....... 79
DIMMER, Display settings ................. 96
Dimmer, Display settings .................... 96
Direct number access mode,
SIRIUS tuning ................................. 64
Direct number access mode,
XM tuning ........................................ 59
DIRECT, Sound field parameter ......... 77
Disconnected,
Bluetooth status message ............... 116
Disconnected, iPod status message .... 116
Display settings, Option menu ............. 96
DIST, Auto setup result ....................... 34
DOCK indicator ................................... 30
Drama, Sound field program ............... 50
DSP effect sound level,
Sound field parameter ...................... 73
DSP indicators ..................................... 31
DSP LEVEL,
Sound field parameter ...................... 73
DVD player connection ....................... 21
DVD recorder connection .................... 22
Dynamic range, Sound menu ............... 91
Index
■
M
Manual delay, Lip sync ........................ 92
MANUAL SETUP ............................... 80
Manual setup ........................................ 80
MANUAL TUNING ............................ 53
Manual tuning mode,
FM/AM tuning ................................. 53
MANUAL, Lip sync ............................ 92
MAX VOL., Audio settings ................. 89
MAX VOL., Zone 2 settings ............... 99
Maximum volume ................................ 89
Maximum volume, Audio settings ....... 89
Memory Guard!, Automatic setup error
message .......................................... 117
Memory guard, Option menu ............... 97
Mono Movie, Sound field program ..... 50
MOVIE, Sound field category ............. 49
MULTI CH INPUT component
selection ........................................... 43
MULTI CH INPUT jacks .................... 25
Multi-channel source playback with
headphones ...................................... 51
Multi-format player connection ........... 25
Multi-information display .................... 31
MULTI-ZONE Configuration ........... 103
MUSIC ENHANCER,
Sound field category ........................ 50
Music Video, Sound field program ...... 49
MUTE .................................................. 45
MUTE indicator ................................... 30
Muting .................................................. 45
■
N
Neo:6 Cinema, Decoder type ......... 77, 78
Neo:6 Music, Decoder type ................. 78
Neural Sur., Decoder type .................... 78
No BT Adapter,
Bluetooth status message ............... 116
NO FRONT SP, Automatic setup
error message ................................. 117
NO MIC, Automatic setup
error message ................................. 117
NO PRNS SP, Automatic setup error
message .......................................... 117
NO SIGNAL, Automatic setup error
message .......................................... 117
NO SIGNAL, XM Satellite Radio status
message .......................................... 114
NO SUR SP, Automatic setup error
message .......................................... 117
NOISY, Automatic setup
error message ................................. 117
NOT SUPPORTED, SIRIUS Satellite
Radio status message ..................... 115
Number of speakers,
Auto setup result .............................. 34
■
O
OFF AIR, XM Satellite Radio status
message .......................................... 114
OPTIMIZER MIC jack ........................ 32
OPTION MENU, Manual setup .......... 96
Option menu, Manual setup ................. 82
OSD SHIFT, Display settings .............. 96
128 En
OSD shift, Display settings ..................96
OSD-AMP, Display settings ................96
OSD-SOURCE, Display settings .........96
Other components controlling by remote
control ............................................101
Other components controlling, Remote
control ............................................101
OUT OF PHASE, Automatic setup
warning message ............................118
Out of Res., HDMI message ................46
OVER 24m (80ft), Automatic setup
warning message ............................118
■
P
P.INIT.DLY,
Sound field parameter ......................74
P.ROOM SIZE,
Sound field parameter ......................75
Pairing, Bluetooth operation ................70
PANORAMA, Decoder parameter ......79
Parameter initialization,
Advanced setup ..............................109
Parametric equalizer type, Auto setup
parameter .........................................33
Parental Lock .......................................65
Parental Lock .......................................65
PARENTAL LOCK,
Input menu .......................................66
PHONES jack ......................................45
PL LEVEL, Sound field parameter ......77
Playing video sources
in the background .............................45
PLII Game, Decoder type ....................78
PLII Movie, Decoder type .............77, 78
PLII Music, Decoder type ....................78
PLIIx Game, Decoder type ..................78
PLIIx Movie, Decoder type ...........77, 78
PLIIx Music, Decoder type ..................78
Power cable connection .......................28
PR LEVEL, Sound field parameter ......77
Presence left speaker level,
Sound field parameter ......................77
Presence right speaker level,
Sound field parameter ......................77
Presence sound field initial delay,
Sound field parameter ......................74
Presence sound field room size,
Sound field parameter ......................75
Presence speaker indicators .................31
Presence speaker using .........................13
Preset channel setting,
XM tuning ..................................60, 65
Preset SCENE templates ......................39
Preset Search mode,
SIRIUS tuning ..................................64
Preset Search mode, XM tuning ..........59
PRESET SEARCH,
SIRIUS tuning ..................................64
PRESET SEARCH, XM tuning ...........59
PRESET TUNING ...............................53
Preset tuning mode,
FM/AM tuning .................................53
Pro Logic, Decoder type ......................78
Projector connection ............................20
Pure Direct ........................................... 52
Pure hi-fi sound ................................... 52
PVR connection ................................... 22
■
R
Rear panel ............................................ 10
REMOTE AMP, Advanced setup ..... 107
Remote control AMP ID,
Advanced setup ............................. 107
Remote control codes ........................... iii
Remote control codes setting ............ 102
Remote control SIRIUS ID, Advanced
setup .............................................. 108
Remote control TUNER ID, Advanced
setup .............................................. 107
Remote control XM ID,
Advanced setup ............................. 108
Remote control,
Troubleshooting ............................ 115
REMOTE IN/OUT jacks ..................... 26
REMOTE SR, Advanced setup ......... 108
REMOTE TU, Advanced setup ......... 107
REMOTE XM, Advanced setup ....... 108
Rename, SCENE template .................. 40
Repeat .................................................. 69
Repeat, iPod playback ......................... 69
Resetting the system .......................... 119
REV.DELAY,
Sound field parameter ..................... 76
REV.LEVEL,
Sound field parameter ..................... 76
REV.TIME,
Sound field parameter ..................... 76
Reverberation delay, Sound field
parameter ......................................... 76
Reverberation level, Sound field
parameter ......................................... 76
Reverberation time,
Sound field parameter ..................... 76
Roleplaying Game,
Sound field program ........................ 49
ROOM SIZE,
Sound field parameter ..................... 75
Room size, Sound field parameter ...... 75
■
S
S VIDEO jacks .................................... 17
S.AUDIO, HDMI set ........................... 98
S.INIT.DLY,
Sound field parameter ..................... 74
S.LIVENESS,
Sound field parameter ..................... 75
S.ROOM SIZE,
Sound field parameter ..................... 75
SB INI.DLY,
Sound field parameter ..................... 74
SB LEVEL,
Sound field parameter ..................... 77
SB LIVENESS,
Sound field parameter ..................... 75
SB ROOM SIZE,
Sound field parameter ..................... 75
SBR->SBL, Automatic setup error
message ......................................... 117
Index
■
T
Test tone, Basic menu ..........................88
Test tone, Equalizer ..............................90
TEST, Equalizer .................................. 90
The Bottom Line,
Sound field program ........................ 49
The Roxy Theatre,
Sound field program ........................ 49
Tonal quality adjustment ..................... 52
Troubleshooting ................................. 110
Tuner indicators ................................... 30
Tuner, Troubleshooting ..................... 113
Turning off ........................................... 29
Turning on ........................................... 29
TV monitor connection ........................ 20
■
U
Unable to play,
iPod status message ....................... 116
UNIT, Speaker distance ....................... 88
Unit, Speaker distance ......................... 88
Unknown iPod,
iPod status message ....................... 116
Unplug HP!, Automatic setup error
message ......................................... 117
Unprocessed input sources .................. 51
UPDATING, SIRIUS Satellite Radio
status message ............................... 115
USER CANCEL, Automatic setup error
message ......................................... 117
■
V
VCR connection .................................. 22
VIDEO AUX jacks .............................. 26
VIDEO CONV., Video settings .......... 97
Video conversion, Video settings ........ 97
Video information ............................... 46
VIDEO jacks ....................................... 17
Video jacks .......................................... 17
Video signal flow ................................ 19
Video sources in the background ........ 45
Virtual CINEMA DSP ......................... 51
VIRTUAL indicator ............................ 31
VOL. TRIM, Input menu ..................... 94
VOLUME level indicator .................... 30
Volume menu, Manual setup ............... 81
Volume Trim, Input menu ................... 94
■
W
W-1:OUT OF PHASE, Automatic setup
warning message ........................... 118
W-2:OVER 24m (80ft), Automatic setup
warning message ........................... 118
W-3:LEVEL ERROR, Automatic setup
warning message ........................... 118
W-4:CHECK PRNS, Automatic setup
warning message ........................... 118
■
X
XM Mini-Tuner Dock ......................... 57
XM Mini-Tuner Dock connection ....... 57
XM Satellite Radio .............................. 57
XM satellite radio activation ............... 58
XM Satellite Radio display ................. 61
XM satellite radio tuning ..................... 57
XM Satellite Radio,
Troubleshooting ............................ 114
129 En
English
SPEAKER, Dynamic range .................91
SPEAKER,
Low frequency effect level ..............91
Speakers, Dynamic range .....................91
Speakers,
Low frequency effect level ..............91
Specifications .....................................124
Spectacle, Sound field program ...........49
Sports, Sound field program ................49
SR LEVEL, Sound field parameter ......77
SR PIN, Advanced setup ....................109
Standard, Sound field program ............49
STANDBY CHARGE, Input menu .....94
Standby mode, Main zone ....................29
Standby mode, Zone 2 ........................105
START PAIRING, Input menu ............95
STEREO, Sound field category ...........50
Straight .................................................51
Straight Enhancer,
Sound field program ........................50
Straight mode .......................................51
SUB UPDATED, SIRIUS Satellite Radio
status message ................................115
SUBWOOFER PHASE,
Speaker settings ...............................87
Subwoofer phase, Speaker settings ......87
SUBWOOFER PRE OUT jack
connection ........................................24
Supplied accessories ...............................2
Support audio, HDMI set .....................98
SUR. L/R SP, Speaker settings ............86
SUR.B L/R SP, Speaker settings ..........86
SUR.BACK PRE OUT jack
connection ........................................24
Surround back left/right speakers,
Speaker settings ...............................86
Surround back sound field initial delay,
Sound field parameter ......................74
Surround back sound field liveness,
Sound field parameter ......................75
Surround back sound field room size,
Sound field parameter ......................75
Surround back speaker level,
Sound field parameter ......................77
Surround decode mode .........................78
Surround left speaker level,
Sound field parameter ......................77
Surround left/right speakers,
Speaker settings ...............................86
SURROUND PRE OUT jack
connection ........................................24
Surround right speaker level,
Sound field parameter ......................77
Surround sound field initial delay, Sound
field parameter .................................74
Surround sound field liveness,
Sound field parameter ......................75
Surround sound field room size,
Sound field parameter ......................75
SYSTEM OFF ......................................29
ADDITIONAL
INFORMATION
SCENE 1 ................................................ 8
SCENE 2 ................................................ 8
SCENE 3 ................................................ 8
SCENE 4 ................................................ 8
SCENE IR code setting,
Advanced setup .............................. 109
SCENE IR, Advanced setup .............. 109
SCENE template rename ..................... 40
Sci-Fi, Sound field program ................. 49
Searching...,
Bluetooth status message ............... 116
Selection, Audio input jacks ................ 44
Selection, Front speaker set ................. 43
Selection, MULTI CH INPUT
component ....................................... 43
Selection, SCENE template ................. 37
SET MENU usage ............................... 84
Setting SCENE template input source,
Remote control ................................ 41
Set-top box connection ........................ 22
Shuffle, iPod playback ......................... 69
SIGNAL INFO .................................... 46
Signal information ............................... 83
SILENT CINEMA ............................... 51
SILENT CINEMA indicator ................ 31
Sirius ID ............................................... 63
SIRIUS Parental Lock personal
identification number reset,
Advanced setup .............................. 109
SIRIUS Satellite Radio ........................ 62
SIRIUS Satellite Radio activation ....... 63
SIRIUS Satellite Radio Parental Lock,
Input menu ....................................... 66
SIRIUS Satellite Radio,
Troubleshooting ............................. 115
SiriusConnect tuner connection ........... 62
SL LEVEL, Sound field parameter ...... 77
SLEEP indicator .................................. 31
Sleep timer ........................................... 47
Sound field indicators .......................... 30
Sound field parameter changing .......... 72
Sound field programs ........................... 48
Sound field programs
with headphones .............................. 51
Sound field programs
without surround speakers ............... 51
SOUND MENU, Manual setup ........... 90
Sound menu, Manual setup .................. 81
Source feature OSD display time,
Display settings ................................ 96
SP A B indicators ................................. 31
SP IMP., Advanced setup .................. 106
SP, Auto setup result ............................ 34
Speaker cable connection ..................... 16
Speaker distance, Auto setup result ..... 34
Speaker distance, Basic menu .............. 88
Speaker distances ................................. 88
Speaker impedance setting ................... 28
Speaker impedance,
Advanced setup .............................. 106
Speaker level adjustment ..................... 52
Speaker level, Auto setup result .......... 34
Speaker level, Basic menu ................... 87
Speaker settings, Basic menu ............... 85
Index
■
Y
YPAO indicator ................................... 30
■
Z
Zone 2 ................................................ 103
Zone 2 Initial volume,
Zone 2 settings ................................. 99
Zone 2 Maximum volume,
Zone 2 settings ................................. 99
Zone 2 settings, Option menu .............. 99
Zone B .................................................. 43
ZONE2 indicator .................................. 31
“ASPEAKERS” or “4DVD”
(example) indicates the name of
the parts on the front panel or the
remote control. Refer to the
attached sheet or the pages at the
end of this manual for the
information about each position of
the parts.
130 En
■ Front panel
A B
C D
E
F
G
H
I
J
VOLUME
SPEAKERS
EDIT
SEARCH MODE
BAND
CATEGORY
A/B/C/D/E
PRESET/TUNING/CH
MEMORY
INFO
ZONE 2
ON/OFF
ZONE
CONTROL
SCENE
1
2
3
4
PROGRAM
MAIN ZONE
SYSTEM OFF
PHONES
TONE CONTROL
INPUT
STRAIGHT
PURE DIRECT
AUDIO SELECT
VIDEO AUX
OPTIMIZER MIC
ON/OFF
SILENT CINEMA
K
i
L
EFFECT
M
N O
S VIDEO
P
Q
R
S
VIDEO
L
AUDIO
R
OPTICAL
■ Remote control
1
2
3
4
POWER
POWER
TV
AV
A
STANDBY
POWER
XM
SIRIUS
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
VCR
B
AMP
TV INPUT
TV MUTE
1
2
H
I
J
K
TV CH
L
TV VOL
5
SCENE
6
7
9
4
SRCH MODE
VOLUME
MENU
BAND LEVEL
TITLE
8
3
N
ENTER
DISPLAY
RETURN
MEMORY
M
O
REC
0
A
l
PROG h
1
2
ENHANCER SUR. DECODE
3
STRAIGHT PURE DIRECT
5
6
7
MULTI CH IN AUDIO SEL
9
0
4
PARAMETER
10
8
SLEEP
ENT
P
Q
R
S
t
APPENDIX
B
C
D
E
F
G
INFO
ii
List of remote control codes
Blu-ray player
Samsung
2137
CD player
Yamaha
5000, 5013
CD Recorder
Yamaha
5001
DVD
Acoustic Solutions
2078
Aiwa
2055, 2100
Akai
2096
Akura
2076
Alba
2078, 2086
Apex
2027, 2049
Awa
2078
Axion
2078
Brainwave
2096
Brandt
2073, 2085
Broksonic
2060
Bush
2075, 2078, 2112
Centrex
2077
Classic
2078
Clatronic
2075
Coby
2078
C-Tech
2074
CyberHome
2025, 2079, 2091
Daewoo
2092, 2098
Dansai
2096
Daytek
2080, 2089
DEC
2075
Denon
2030, 2102, 2103
Denver
2075, 2076
Diamond
2074
DK Digital
2094
Dual
2078
D-Vision
2096
DVX
2074
Elta
2096
Euroline
2096
Funai
2052, 2058
Global Solutions2074
Global Sphere 2074
Goodmans
2075, 2077, 2078
Grundig
2077, 2098
H&B
2075
Haaz
2074
HE
2078
Hitachi
2032, 2072
Home Electronics
2078
Innovation
2072
Irradio
2134
JDB
2078
JVC
2033, 2045, 2053,
2073, 2099
Kenwood
2030, 2097
Kingavon
2075
Koda
2075
Lawson
2074
Lenco
2075
LG
2084, 2087
Lifetec
2072
Limit
2074
LogicLab
2074
Luxor
2077
Magnavox
2037, 2073, 2075
Magnum
2072
iii
MBO
Medion
Micromaxx
Micromedia
Microstar
Mitsubishi
Mizuda
Mustek
Naiko
Onkyo
Orava
P&B
Pacific
Panasonic
2078
2072
2072
2073
2072
2035
2075
2078
2077
2073, 2135
2075
2075
2074
2030, 2040, 2054,
2057, 2105, 2110
Philips
2019, 2026, 2046,
2073, 2081, 2090
Pioneer
2036, 2082
Proline
2077
Provision
2075
RCA
2031, 2042, 2050,
2051
Red Star
2076
Reoc
2074
Roadstar
2075, 2078, 2086
Rowa
2077
Saba
2085
Sabaki
2074
Samsung
2032, 2041, 2104,
2113
Sansui
2074
Sanyo
2095
ScanMagic
2078
Scientific Labs 2074
Scott
2088
SEG
2074, 2086
Sharp
2034, 2043, 2059,
2093, 2106
Silva
2076
Singer
2074
Skymaster
2074, 2078
Skyworth
2076
SM Electronic 2074, 2078
Sony
2028, 2029, 2039,
2083, 2107
Soundmaster
2074
Soundmax
2074
Standard
2074
Star Cluster
2074
Starmedia
2075
Supervision
2074, 2078
Sylvania
2052, 2058
Synn
2074
TCM
2072
Teac
2074
Tec
2076
Technics
2030
Technika
2096
Technosonic
2096
Tevion
2072, 2074
Thomson
2085, 2109
Tokai
2076
Toshiba
2026, 2044, 2048,
2056, 2073, 2108,
2111
United
2078
Voxson
2078
Wharfedale
2074
Xlogic
2074
Yakumo
2077
Yamada
2077
Yamaha
Yukai
Zenith
2000, 2001, 2003,
2030, 2101
2078
2038, 2047, 2073
DVD Recorder
Apex
JVC
LG
Panasonic
Philips
Pioneer
RCA
Sony
Toshiba
Yamaha
Yukai
2024
2070
2071
2020, 2065, 2066,
2067
2019, 2061, 2062,
2063
2021
2018
2022, 2064
2068
2023
2069
DVD/LD
Pioneer
2036
DVD/VCR
JVC
LG
Panasonic
Philips
RCA
Samsung
Sharp
Sony
Toshiba
Zenith
1017, 2045
1071, 2087
1020, 1072, 2040,
2105
1025
1022, 2042
1021, 2041, 2104
1023, 1073, 2043,
2106
1019, 1074, 2039,
2107
1024, 1075, 2044,
2108
1026, 2047
DVD-DVR
Panasonic
Pioneer
Samsung
Toshiba
2132
2132
2132
2132
2015, 2016, 2017,
2120
Philips
2117, 2121, 2123,
2128
Pioneer
2012, 2013, 2014
Proscan
2129
RCA
2116, 2124, 2129,
2133
ReplayTV
2118, 2119, 2120
Sharp
2009, 2010
Sonic Blue
2119, 2120
Sony
2005, 2006, 2007,
2122, 2130, 2131,
2132
Stack 10
2132
Stack 9
2132
Systemax
2132
Tagar Systems 2132
Tivo
2116, 2121, 2122,
2123, 2130, 2131
Toshiba
2004, 2125, 2132
Touch
2132
UltimateTV
2133
Viewsonic
2132
Voodoo
2132
Yamaha
2011
ZT Group
2132
HD DVD
Toshiba
2132
2132
2132
2132
2123, 2128, 2129,
2133
DISH Network 2126, 2127
Dishpro
2126
Echostar
2126, 2127
Expressvu
2126
Gateway
2132
GOI
2126
Hewlett Packard 2132
Hitachi
2008
Howard Computers
2132
HTS
2126
Hughes
2123, 2128
Humax
2123
Hush
2132
iBUYPOWER 2132
JVC
2126, 2127
Linksys
2132
Media Center PC
2132
2136
iPod
Yamaha
5011
LD player
Yamaha
2067
2114
2115
2068
DVR
ABS
Alienware
CyberPower
Dell
DIRECTV
Microsoft
Mind
Niveus Media
Northgate
Panasonic
2002
MD
Yamaha
5002, 5003, 5004
TAPE DECK
Yamaha
5005, 5006
TUNER
Yamaha
5007, 5008, 5009,
5010, 5012, 5014,
5015, 5016, 5017,
5018
TV
Acer
Acme
Acura
ADA
ADC
Admiral
Adyson
Agashi
Agazi
AGB
Aiko
Aiwa
0093
0207
0208
0255
0206
0058, 0205, 0206,
0210, 0211
0200, 0207
0200
0206
0204
0127, 0200, 0207,
0208
0028, 0139, 0229,
0237
Akai
Cascade
Cathay
CCE
Celebrity
Centurion
Century
CGE
Cimline
Citizen
0208
0213, 0217
0127
0059
0213, 0217
0205
0214, 0215
0208, 0218
0060, 0061, 0062,
0064
City
0208
Clarivox
0212, 0217
Clatronic
0206, 0207, 0208,
0209, 0213, 0214,
0218
CMS
0200
Colortyme
0060, 0061
Concerto
0060, 0061
Concorde
0208
Condor
0200, 0207, 0213
Contec
0200, 0207, 0208
Contec/Cony 0062
Continental Edison
0216
Cosmel
0208
Craig
0062
Crosley
0205, 0214, 0215
Crown
0062, 0063, 0128,
0208, 0213, 0217
CS Electronics 0200, 0207, 0209,
0214, 0218
CTC
0214
Curtis Mathes 0057, 0060, 0061,
0064, 0065
CXC
0062
Cybertron
0209, 0218
Daewoo
0060, 0061, 0120,
0127, 0155, 0193,
0200, 0207, 0208,
0213, 0218, 0238
Dainichi
0200, 0209, 0218
Dansai
0200, 0206, 0213,
0217
Dantax
0217
Daytron
0060, 0061, 0208
De Graaf
0210
Decca
0204, 0207, 0213,
0217
Desmet
0213, 0217
Diamond
0200
Dimensia
0057
Dixi
0208, 0213, 0217
DTS
0208
Dual
0207, 0215, 0216
Dual-Tec
0207, 0208, 0215
Dumont
0060, 0127, 0205,
0207
Durabrand
0126
Dux
0217
Dynatron
0213, 0217
Elbe
0203, 0204, 0212,
0218
Elbe-Sharp
0204
Elcit
0204, 0205
ELECTRO TECH
0208
Electroband
0059
Electrohome
0059, 0060, 0061
Elin
0200, 0207, 0213,
0217
Elite
0209, 0213, 0218
Elman
0215
Elta
0200, 0208
Emerson
0060, 0061, 0062,
0064, 0128, 0205
Envision
Erres
ESA
Etron
Euro-Feel
Euroline
Euroman
Euromann
Europhon
0060, 0061
0213, 0217
0080
0208
0206
0217
0200
0206, 0207, 0213
0200, 0204, 0207,
0213, 0215
Fenner
0208
Ferguson
0212, 0217, 0226
Fidelity
0200, 0207, 0210
Finlandia
0210
Finlux
0204, 0205, 0207,
0213, 0215, 0217
Firstline
0200, 0207, 0208,
0213, 0214
Fisher
0064, 0127, 0128,
0205, 0207, 0215
Flint
0213, 0218
Formenti
0200, 0205, 0207,
0215, 0217
Formenti-Phoenix
0200
Fortress
0205
Frontech
0206, 0208, 0210,
0211, 0214
Fujitsu
0023, 0024, 0025,
0088, 0127
Funai
0033, 0034, 0035,
0036, 0037, 0062,
0206
Futuretech
0062
Gateway
0094
GBC
0208, 0215, 0218
GE
0057, 0060, 0061,
0122, 0147
GEC
0204, 0207, 0211,
0213, 0217
Geloso
0208, 0210, 0215
General Technic 0208
Genexxa
0209, 0211, 0213,
0218
Gibralter
0060
GoldHand
0200
GoldStar
0060, 0061, 0127,
0128, 0200, 0201,
0207, 0208, 0210,
0213, 0214, 0215,
0217
Goodmans
0171, 0201, 0204,
0206, 0208, 0213,
0217, 0240
GPM
0209, 0218
Graetz
0211
Granada
0204, 0207, 0210,
0213, 0217
Grandin
0208, 0209, 0217
Grundig
0128, 0130, 0222,
0236, 0255
Grunpy
0062
Halifax
0200, 0206, 0207
Hallmark
0060, 0061
Hampton
0200, 0207
Hanseatic
0203, 0207, 0208,
0213, 0215, 0217
Hantarex
0204, 0208
Harvard
0062
HCM
0206, 0207, 0208,
0218
Hifivox
0216
Higashi
0200
Hinari
0208, 0209, 0213,
0217, 0218
Hisawa
Hitachi
0209, 0218
0006, 0014, 0015,
0016, 0042, 0060,
0061, 0095, 0105,
0127, 0156, 0179,
0180, 0204, 0207,
0210, 0211, 0215,
0216, 0251
Hornyphon
0213
Hoshai
0209, 0218
Huanyu
0200, 0207
Hygashi
0200, 0207
Hyper
0200, 0207, 0208,
0214, 0215
Hypson
0206, 0207, 0213,
0217
ICE
0127, 0200, 0206,
0207, 0208, 0209,
0213, 0218
ICeS
0200, 0218
IMA
0062
Imperial
0211, 0213, 0214,
0215
Indiana
0213, 0217
Infinity
0063
Ingelen
0211
Ingersol
0208
Inno Hit
0201, 0204, 0207,
0208, 0209, 0213,
0217, 0218
Innovation
0206, 0208
Interbuy
0208, 0214
Interfunk
0205, 0211, 0213,
0214, 0216, 0217
International
0200
Intervision
0206, 0207, 0218
Irradio
0201, 0208, 0209,
0213, 0217, 0218
Isukai
0209, 0218
ITC
0207, 0215
ITS
0200, 0209, 0213,
0218
ITT
0129, 0208, 0211
ITV
0208, 0217
JBL
0063
JC Penney
0057, 0060, 0061
JCB
0059
Jensen
0060, 0061
JVC
0017, 0018, 0019,
0108, 0136, 0153,
0178, 0190, 0213,
0218
Kaisui
0200, 0207, 0208,
0209, 0218
Kamosonic
0207
Kamp
0200, 0207
Kapsch
0211
Karcher
0207, 0208, 0212,
0217
Kawasho
0059, 0060, 0061,
0200
Kendo
0128, 0210
Kennedy
0215
Kenwood
0060, 0061
Kingsley
0200, 0207
Kloss Novabeam
0062
Kneissel
0203
Kolster
0213
Konka
0209, 0218
Korpel
0213, 0217
Korting
0205
Koyoda
0208
KTV
0062, 0127, 0207
Kyoto
0200, 0212
iv
APPENDIX
0059, 0065, 0127,
0129, 0130, 0200,
0204, 0208, 0209,
0213, 0217, 0218,
0255
Akiba
0209, 0218
Akura
0206, 0209, 0218
Alaron
0200
Alba
0200, 0207, 0208,
0209, 0217, 0218
ALBIRAL
0212
Allstar
0213
Amplivision
0207
Amstrad
0204, 0206, 0208,
0209, 0218
Amtron
0062
Anam
0208
Anam National 0062
Anglo
0208
Anitech
0206, 0208
Ansonic
0203, 0208
AOC
0060, 0061
Apex
0118, 0122, 0132
Arc en Ciel
0216
Arcam
0200
Arcam Delta
0207
Aristona
0213, 0217
ASA
0205, 0211
Asberg
0213
Astra
0208
Asuka
0200, 0206, 0207,
0209, 0218
Atlantic
0200, 0207, 0213,
0217
Atori
0208
Audiosonic
0207, 0208, 0209,
0213, 0216, 0217,
0218
AudioTon
0207
Audiovox
0062
Autovox
0205, 0206, 0207
Awa
0200
Baird
0216
Bang & Olufsen 0205
Basic Line
0208, 0209, 0213,
0218
Bastide
0207
Baur
0217
Beko
0228
Belcor
0060
Bell & Howell 0058, 0064
Benq
0081
Beon
0213, 0217
Bestar
0213
Binatone
0207
Black Star
0214
Blaupunkt
0255
Blue Sky
0209, 0218
Bondstec
0214
Boots
0207
Bradford
0062
Brandt
0216, 0226
Brionvega
0205, 0213, 0217
Britannia
0200, 0207
Brockwood
0060
Broksonic
0138
Bruns
0205
BSR
0215
BTC
0209, 0218
Bush
0177, 0208, 0209,
0210, 0213, 0215,
0216, 0217, 0218,
0230, 0237
Candle
0060, 0061
Capsonic
0206
Lenco
Lenoir
Lesa
Leyco
LG
0208
0207, 0208
0214
0206, 0213, 0217
0016, 0038, 0039,
0127, 0128, 0157,
0158, 0163, 0164,
0166, 0188, 0189,
0200, 0201, 0207,
0208, 0210, 0213,
0214, 0215, 0217
Liesenk
0217
Life
0206, 0208
Lifetec
0206, 0208, 0218
Loewe
0063, 0128, 0203,
0204, 0223, 0227
Loewe Opta
0205, 0213, 0217
Logik
0058
Luma
0210, 0217
Lumatron
0210, 0213, 0217
Lux May
0213
Luxman
0060, 0061
Luxor
0201, 0207, 0210
LXI
0057, 0061, 0063,
0064
Magnadyne
0204, 0205, 0214,
0215, 0217
Magnafon
0200, 0204, 0207
Magnavox
0060, 0061, 0063,
0102, 0103, 0150
Magnum
0206, 0208
Majestic
0058
Mandor
0206
Manesth
0206, 0207, 0213,
0217
Marantz
0060, 0061, 0063,
0090, 0213, 0217
Marelli
0205
Mark
0200, 0213, 0217
Matsui
0204, 0207, 0208,
0210, 0213, 0217
Mediator
0213, 0217
Medion
0206, 0208
Megatron
0061
Melectronic
0200, 0207, 0208,
0211, 0213, 0216,
0217
Memorex
0058, 0061, 0064,
0208
Memphis
0208
Metz
0205
MGA
0060, 0061
Micromaxx
0206, 0208
Microstar
0206, 0208
Minerva
0204
Minoka
0213
Mitsubishi
0006, 0015, 0016,
0048, 0060, 0061,
0104, 0112, 0113,
0125, 0205, 0213
Mivar
0200, 0201, 0202,
0203, 0204, 0207
Montgomery Ward
0058
MTC
0060, 0061, 0128,
0200
Multi System 0217
Multitech
0062, 0127, 0128,
0200, 0207, 0208,
0210, 0214, 0215,
0217
Murphy
0200, 0207
NAD
0061
Naonis
0210
v
NEC
0026, 0053, 0060,
0061, 0096, 0127
Neckermann
0205, 0207, 0210,
0213, 0217, 0255
NEI
0213, 0217
Nesco
0214
NET-TV
0082, 0101
New Tech
0208, 0213
New World
0209, 0218
Nicamagic
0200, 0207
Nikkai
0200, 0206, 0207,
0209, 0213, 0217,
0218
Nikko
0061
Nobliko
0200, 0207
Nogamatic
0216
Nokia
0129, 0211
Nordmende
0205, 0211, 0213,
0216
Nordvision
0217
Oceanic
0211
Olevia
0084
ONCEAS
0207
Onwa
0062, 0218
Orbit
0213
Orion
0126, 0204, 0208,
0213, 0217, 0235
Orline
0218
Orsowe
0204
Osaki
0127, 0206, 0207,
0209, 0218
Osio
0201
Oso
0209, 0218
Osume
0218
Otto Versand 0204, 0207, 0213,
0215, 0216, 0217,
0255
Pael
0200, 0207
Palladium
0207
Panama
0200, 0206, 0207,
0208
Panasonic
0006, 0007, 0063,
0073, 0074, 0097,
0110, 0114, 0137,
0141, 0151, 0162,
0165, 0186, 0204,
0211, 0244, 0245,
0246, 0254
Pathe Cinema 0200, 0203, 0207,
0212, 0215
Pathe Marconi 0212, 0216
Pausa
0208
Perdio
0200
Philco
0060, 0061, 0063,
0128, 0205, 0214,
0215
Philharmonic 0207
Philips
0040, 0060, 0063,
0072, 0115, 0116,
0124, 0130, 0150,
0175, 0184, 0187,
0205, 0207, 0213,
0215, 0217, 0220,
0221, 0232, 0233,
0252, 0253
Philips Magnavox
0124
Phoenix
0200, 0205, 0213,
0217
Phonola
0200, 0205, 0213,
0217
Pilot
0060
Pioneer
0012, 0013, 0060,
0061, 0098, 0109,
0117, 0128, 0181,
0182, 0194, 0195,
0211, 0213, 0216,
0217, 0250
Plantron
0206, 0213
Polaroid
0075
Poppy
0208
Portland
0060, 0061
Prandoni-Prince 0204, 0210
Precision
0207
Prima
0208, 0211
Profex
0208
Profi-Tronic
0213
Proline
0213
Proscan
0057
Prosonic
0200, 0207, 0217
Protech
0206, 0207, 0208,
0213, 0214, 0215,
0217
Proton
0060, 0061
Provision
0217
Pulsar
0060
Pye
0213, 0217
Pymi
0208
Quasar
0152, 0214
Quelle
0201, 0206, 0207,
0213, 0214, 0215,
0217
Radialva
0218
Radio Shack
0064
Radio Shack/Realistic
0057, 0060, 0061,
0062, 0064
Radiola
0213, 0217
Radiomarelli
0204, 0205, 0214
Radiotone
0213
RCA
0057, 0060, 0061,
0091, 0133, 0135,
0147, 0149
Realistic
0064
Revox
0213, 0217
Rex
0206, 0210, 0211
RFT
0203, 0205
Rhapsody
0200
R-Line
0213, 0217
Roadstar
0206, 0208, 0209,
0218, 0237
Robotron
0205
Rowa
0200
RTF
0205
Saba
0204, 0205, 0211,
0216
saccs
0212
Saisho
0204, 0206, 0207,
0208
Salora
0201, 0204, 0210,
0211, 0215
Sambers
0204
Sampo
0060, 0061, 0083,
0101
Samsung
0029, 0030, 0031,
0032, 0044, 0045,
0046, 0047, 0060,
0061, 0065, 0068,
0069, 0071, 0079,
0087, 0127, 0128,
0130, 0144, 0160,
0161, 0170, 0176,
0183, 0185, 0200,
0201, 0206, 0207,
0208, 0213, 0217,
0239, 0241, 0242,
0243
Sandra
0200, 0207
Sansui
0123, 0126, 0213
Sanyo
0020, 0021, 0022,
0049, 0060, 0064,
0127, 0128, 0200,
0203, 0207, 0215
SBR
0217
SCHAUB LORENTZ
0211
Schneider
0207, 0209, 0213,
0215, 0216, 0217,
0218
Scotch
0061
Scott
0060, 0061, 0062
Sears
0057, 0060, 0061,
0064
SEG
0200, 0206, 0207,
0214, 0215, 0217
SEI
0204
SEI-Sinudyne 0204, 0205, 0211
Seleco
0210, 0211, 0215
Sencora
0208
Sentra
0218
Serino
0200
Sharp
0009, 0010, 0011,
0060, 0061, 0066,
0070, 0087, 0111,
0143, 0145, 0167,
0168, 0169, 0198,
0204, 0224, 0247,
0248, 0249
Shogun
0060
Siarem
0204, 0205, 0215
Sicatel
0212
Siemens
0255
Sierra
0213
Signature
0058
Silva
0200
Singer
0205, 0214, 0215
Sinudyne
0204, 0205, 0215,
0217
Skantic
0211
Solavox
0211
Sonoko
0206, 0207, 0208,
0213, 0217
Sonolor
0211
Sontec
0213, 0217
Sony
0041, 0059, 0067,
0085, 0086, 0174,
0196, 0199, 0208,
0219, 0234
Sound & Vision 0209, 0218
Soundesign
0060, 0061, 0062
Soundwave
0213, 0217
SSS
0060, 0062
Standard
0207, 0208, 0209,
0213, 0218
Starlight
0217
Starlite
0062
Stenway
0218
Stern
0210, 0211
Sunkai
0208, 0218
Sunwood
0208, 0213
Superla
0200, 0204, 0207
SuperTech
0200
Supra
0208
Supreme
0059
Susumu
0209
Sutron
0208
Sydney
0200, 0207
Sylvania
0060, 0061, 0063,
0080, 0134, 0142,
0148
Symphonic
0062, 0080
Sysline
0217
Sytong
0200
Tandy
Weltblick
0213, 0217
Weston
0215
White Westinghouse
0200, 0207, 0217
Yamaha
0000, 0001, 0002,
0003, 0004, 0005,
0060, 0061
Yamishi
0218
Yoko
0200, 0206, 0207,
0208, 0209, 0213,
0217, 0218
Yorx
0209, 0218
Zanussi
0210
Zenith
0058, 0060, 0100,
0105, 0119, 0121,
0154
TV/DVD
Aiwa
Apex
Broksonic
Bush
JVC
Panasonic
RCA
Sylvania
Thomson
Toshiba
0139, 2055
0132, 2049
0138, 2060
0230, 2112
0136, 2053
0137, 0254, 2054,
2110
0133, 0135, 2050,
2051
0134, 2052
0226, 2109
0131, 0231, 2048,
2111
TV/DVD/VCR
Panasonic
Samsung
Sharp
Sylvania
Toshiba
0141, 1040, 2057
0241, 1070, 2113
0143, 1028, 2059
0142, 1041, 2058
0140, 1029, 2056
TV/VCR
Aiwa
Bush
Daewoo
GE
Goodmans
Grundig
Hitachi
JVC
Magnavox
Orion
Panasonic
Philips
Quasar
RCA
Roadstar
Samsung
Sharp
Sony
Sylvania
Tatung
Toshiba
Zenith
0237, 1066
0237, 1066
0155, 0238, 1038,
1067
0147, 1030
0240, 1069
0236, 1062
0156, 1039
0153, 1036
0150, 1033
0235, 1065
0151, 1034
0150, 0232, 0233,
1033, 1062, 1063
0152, 1035
0149, 1032
0237, 1066
0144, 0239, 1027,
1068
0145, 1028
0234, 1064
0148, 1031
0237, 1066
0146, 0237, 1029,
1066
0154, 1037
VCR
Admiral
Adventura
Aiwa
Akai
Akiba
Akura
1008, 1013
1005
1005, 1042, 1043,
1044, 1066
1007, 1043
1050
1043, 1050
Alba
American High
Amstrad
Anitech
ASA
Asha
Asuka
1044, 1050
1004
1042
1050
1045, 1046
1002, 1014
1042, 1045, 1046,
1050
Audio Dynamics1000
Audiovox
1003
Baird
1042, 1043, 1047
Basic Line
1044, 1050
Baur
1046
Beaumark
1002, 1014
Bell & Howell 1001
Blaupunkt
1046, 1048
Broksonic
1012, 1013
Bush
1044, 1050, 1066
Calix
1003
Candle
1002, 1003
Canon
1004
CCE
1006
CGE
1042, 1043
Cimline
1044, 1050
Citizen
1002, 1003
Colortyme
1000
Colt
1006
Craig
1002, 1003, 1006,
1014
Crown
1050
Curtis Mathes 1000, 1002, 1004,
1009
Cybernex
1002, 1014
Daewoo
1005, 1038, 1061,
1067
Dansai
1050
Dantax
1044
DBX
1000
De Graaf
1046, 1049
Decca
1042, 1043, 1046
Denon
1010
Dimensia
1009
Dual
1043, 1046
Dumont
1042, 1046, 1047,
1049
Dynatech
1005
Electrohome
1003
Electrophonic 1003
Elta
1050
Emerson
1003, 1004, 1005,
1012, 1013
Etzuko
1050
Ferguson
1043
Fidelity
1042
Finlandia
1046, 1047, 1049
Finlux
1042, 1043, 1046,
1047, 1049
FIRST LINE 1044, 1045, 1049,
1050
Fisher
1001, 1047
Flint
1044
Formenti/Phoenix
1046
Fuji
1004
Fujitsu
1042
Funai
1005, 1042
Galaxy
1042
Garrard
1005
GBC
1050
GE
1002, 1004, 1009,
1014, 1030
GEC
1046
Geloso
1050
General Technic 1044, 1048
Go Video
1014
GoldHand
Goldstar
1050
1000, 1003, 1042,
1045
Goodmans
1042, 1045, 1050,
1069
Gradiente
1005
Graetz
1043, 1047
Granada
1046, 1047, 1049
Grandin
1042, 1045, 1050
Grundig
1046, 1050, 1062
Hanseatic
1045, 1046
Harley Davidson1005
Harman/Kardon 1000
Harwood
1006
HCM
1050
Headquarter
1001
Hinari
1044, 1050
Hisawa
1044
Hitachi
1007, 1010, 1039,
1042, 1043, 1046,
1049
Hughes Network Systems
1010
Hypson
1044, 1050
Imperial
1042
Inno Hit
1046, 1050
Innovation
1044, 1048
Instant Replay 1004
Interbuy
1045
Interfunk
1046, 1047
Intervision
1042
Irradio
1045, 1050
ITT
1043, 1047
ITV
1045
JC Penney
1000, 1001, 1002,
1003, 1004, 1006
JCL
1004
Jensen
1007
JVC
1000, 1001, 1007,
1011, 1017, 1036,
1043
Kaisui
1050
Karcher
1046
Kendo
1044
Kenwood
1000, 1001, 1007,
1011, 1043
KLH
1006
Kodak
1003, 1004
Korpel
1050
Leyco
1050
LG
1003, 1042, 1045,
1071
Lifetec
1044, 1048
Lloyd's
1005
Loewe
1048
Loewe Opta
1045, 1046
Logik
1006, 1050
Luxor
1047
LXI
1003
M Electronic 1042
Magnasonic
1047
Magnavox
1004, 1018, 1033
Magnin
1003, 1014
Manesth
1050
Marantz
1000, 1001, 1004,
1046, 1051
Marta
1003
Matsui
1044, 1045
Matsushita
1004
Mediator
1046
Medion
1044, 1048
MEI
1004
vi
APPENDIX
0127, 0207, 0209,
0211, 0218
Tashiko
0200, 0207, 0210
Tatung
0127, 0204, 0207,
0213, 0217, 0237
TCM
0206, 0208
Teac
0127
Tec
0207, 0208, 0214,
0215
Techwood
0060, 0061
Teknika
0058, 0060, 0061,
0062
Teleavia
0216
Telecor
0218
Telefunken
0065, 0213, 0216
Telegazi
0218
Teletech
0208, 0214, 0217
Teleton
0207
Televideon
0200
Tensai
0208, 0209, 0213,
0218
Tesmet
0213
Tevion
0206, 0208
Texet
0200, 0207
Thomson
0191, 0192, 0207,
0213, 0216, 0226
Thorn
0212, 0217
TMK
0060, 0061
Tokai
0213
Tokyo
0200, 0207
Toshiba
0027, 0043, 0053,
0054, 0064, 0078,
0089, 0090, 0106,
0107, 0127, 0131,
0140, 0146, 0159,
0197, 0225, 0231,
0237
Towada
0211, 0215
Transtec
0200
Trident
0204
Tristar
0218
Triumph
0204
Uher
0211, 0213
Ultravox
0200, 0205, 0207,
0214, 0215
United
0217
Universum
0127, 0128, 0129,
0201, 0206, 0213,
0214, 0215, 0217
Univox
0212
Vestel
0210, 0211, 0213,
0214, 0215, 0217
Vexa
0208, 0217
Victor
0213
VIDEOLOGIC 0200
Videologique 0200, 0207, 0209,
0218
Videosat
0214
VideoSystem 0213
Videotechnic 0200
Vidtech
0060, 0061
Viewsonic
0076, 0077, 0092,
0099, 0172, 0173
Visiola
0200, 0207
Vision
0213
Vortec
0213, 0217
Voxson
0205, 0210, 0211,
0213
Waltham
0207, 0212
Wards
0057, 0058, 0060,
0061, 0063
Watson
0213, 0217, 0218
Watt Radio
0200, 0207, 0212,
0215
Wega
0205
Memorex
1001, 1002, 1003,
1004, 1005, 1008,
1013, 1014, 1042,
1045, 1047
Memphis
1050
Metz
1048
MGA
1014
MGN Technology
1002, 1014
Micromaxx
1044, 1048
Microstar
1044, 1048
Migros
1042
Minolta
1010
Mitsubishi
1011, 1042, 1046
Montgomery Ward
1008
Motorola
1004, 1008
MTC
1002, 1014
Multitech
1002, 1005, 1006,
1042, 1046, 1050
Murphy
1042
National
1048
NEC
1000, 1001, 1007,
1011, 1043, 1051
Neckermann
1043, 1046
NEI
1046
Nesco
1050
Nikko
1003
Noblex
1002, 1014
Nokia
1043, 1047
Nordmende
1043
Oceanic
1042, 1043
Okano
1044
Olympus
1004
Optimus
1003, 1008
Orion
1012, 1013, 1044,
1065
Orson
1042
Osaki
1042, 1045, 1050
Otto Versand 1046
Palladium
1043, 1045, 1050
Panasonic
1004, 1020, 1034,
1040, 1048, 1054,
1072
Pathe Marconi 1043
Penney
1010, 1014
Pentax
1010, 1049
Perdio
1042
Philco
1004, 1051
Philips
1004, 1025, 1033,
1046, 1056, 1057,
1059, 1062, 1063
Philips Magnavox
1018
Phonola
1046
Pilot
1003
Pioneer
1011, 1046
Prinz
1042
Profex
1050
Profitronic
1014
Proline
1042
Proscan
1009
Prosonic
1044
Protec
1006
Pye
1046, 1056
Quarter
1001
Quartz
1001, 1047
Quasar
1004, 1035
Quelle
1042, 1046, 1047
Radio Shack
1003
Radio Shack/Realistic
1001, 1002, 1003,
1004, 1005, 1008
Radiola
1046
Radix
1003
vii
Randex
RCA
1003
1002, 1004, 1009,
1010, 1014, 1015,
1022, 1032
Realistic
1001, 1002, 1003,
1004, 1005, 1008
Rex
1043
RFT
1046
Roadstar
1045, 1050, 1066
Saba
1043
Saisho
1044, 1050
Salora
1047
Samsung
1002, 1014, 1021,
1027, 1052, 1068,
1070
Sanky
1008
Sansui
1007, 1011, 1013,
1043
Sanyo
1001, 1002, 1014,
1047
SBR
1046
Schaub Lorenz 1042, 1043, 1047
Schneider
1042, 1044, 1045,
1046, 1050
Scott
1012
Sears
1001, 1003, 1004,
1010
SEG
1050
SEI-Sinudyne 1046
Seleco
1043
Sentron
1050
Sharp
1008, 1023, 1028,
1053, 1073
Shintom
1006, 1047, 1050
Shivaki
1045
Shogun
1002, 1014
Siemens
1045, 1047
Signature 2000 1008
Silva
1045
Singer
1004, 1006
Sinudyne
1046
Sontec
1045
Sony
1016, 1019, 1055,
1060, 1064, 1074
STS
1004, 1010
Sunkai
1044
Sunstar
1042
Suntronic
1042
Sunwood
1050
Sylvania
1004, 1005, 1031,
1041
Symphonic
1005
Taisho
1044
Tandy
1001
Tashiko
1003, 1042
Tatung
1007, 1042, 1043,
1046, 1066
TCM
1044, 1048
Teac
1005, 1007
Technics
1004, 1048
Teknika
1003, 1004, 1005
Teleavia
1043
Telefunken
1043
Tenosal
1050
Tensai
1042, 1045, 1050
Tevion
1044, 1048
Thomson
1043, 1058
Thorn
1043, 1047
TMK
1002, 1014
Tokai
1045, 1050
Tonsai
1050
Toshiba
1013, 1024, 1029,
1043, 1046, 1066,
1075
Totevision
1002, 1003, 1014
Towada
1050
Towika
1050
Uher
1045
Unitech
1002, 1014
Universum
1042, 1045, 1046
Vector Research 1000
Video Concepts 1000
Videon
1044, 1048
Videosonic
1002, 1014
Wards
1002, 1003, 1004,
1005, 1006, 1008,
1010, 1014
Weltblick
1045
White Westinghouse
1013
XR-1000
1004, 1005, 1006
Yamaha
1000, 1001, 1007
Yamishi
1050
Yokan
1050
Yoko
1045, 1050
Zenith
1013, 1026, 1037
HTR-6160_U-cv.fm Page 1 Monday, December 10, 2007 2:07 PM
U
HTR-6160
HTR-6160
AV Receiver
© 2008
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Black process 45.0° 240.0 LPI
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WN25460
00_sheet_HTR-6160_U.book Page 1 Monday, December 10, 2007 2:19 PM
U
HTR-6160
The circled numbers and alphabets correspond to those in the Owner’s Manual.
■ Front panel
B
A
C
D
E
F
G
H
I
J
VOLUME
SPEAKERS
EDIT
SEARCH MODE
BAND
CATEGORY
A/B/C/D/E
PRESET/TUNING/CH
MEMORY
INFO
ZONE 2
ON/OFF
ZONE
CONTROL
SCENE
1
2
3
4
PROGRAM
MAIN ZONE
SYSTEM OFF
PHONES
INPUT
TONE CONTROL
STRAIGHT
PURE DIRECT
AUDIO SELECT
VIDEO AUX
OPTIMIZER MIC
ON/OFF
SILENT CINEMA
K
Black process 45.0° 240.0 LPI
L
EFFECT
M
N
O
S VIDEO
P
Q
R
S
VIDEO
L
AUDIO
R
OPTICAL
00_sheet_HTR-6160_U.book Page i Monday, December 10, 2007 2:19 PM
■ Remote control
1
2
3
4
POWER
POWER
TV
AV
A
STANDBY
POWER
XM
SIRIUS
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
VCR
B
AMP
TV INPUT
TV MUTE
1
2
H
I
J
K
TV CH
L
TV VOL
5
SCENE
6
7
9
4
SRCH MODE
VOLUME
MENU
BAND LEVEL
TITLE
8
3
N
ENTER
DISPLAY
RETURN
MEMORY
M
O
REC
0
A
B
C
D
E
F
G
INFO
l
PROG h
1
2
ENHANCER SUR. DECODE
3
STRAIGHT PURE DIRECT
5
6
7
MULTI CH IN AUDIO SEL
9
0
4
PARAMETER
10
8
SLEEP
ENT
P
Q
R
S
t
Printed in Malaysia
Black process 45.0° 240.0 LPI
WN67540