Arlight MW-RS09 Instructions
PDF
Download
Document
Advertisement
Advertisement
Microwave sensor instruction Датчик движения MW-RS09 (угол 360°, 2-10м) The sensor is an active motion detector, it emits high-frequency electro-magnetic wave (5.8GHz) and receives their echo. The sensor detects the change in echo from even the slightest movement in its detection zone. A microprocessor then triggers the “switch light ON” command. Detection is possible through doors, panes of glass or thin walls. Important: persons or objects moving towards the sensor are detected best ! NOTE: the high-frequency output of this sensor is <10Mw- that is just one 100th of the transmission power of a mobile phone or the output of a microwave oven. Technical Parameters Power supply: 220-240VAC Installation sit: Indoors, ceiling mounting HF system: 5.8GHz CW radar, ISM band Reach:1-8m, radii., adjustable Time setting 10sec to 30min Power frequency: 50/60Hz Transmission power: <10mW Detection angle: 360° Rated load: 1200W Power consumption: approx.0.9W Connection illumination Connect N, L with power; Connect N, L’ with load. L' N L N LOAD N ~AC Reach setting (sensitivity) Reach is the term used to describe the radius of the circular detection zone produced on the ground. After mounting the sensor light at a height of 2.5m, turn the reach control completely in anti-clockwise direction to select minimum reach (approx.1 m radius), and turn the reach control completely in a clockwise direction to select the maximum reach (approx.10m radius). The LED indicator will flash when the reach control is rotated. It flashes 1 to 10 times, representing 1m to 8m for the radius of the detection zone. 1-8m radii NOTE: The above detection distance is measured using a person who is between 1.6m~1.7m tall with an average build, moving at a speed of 1.0~1.5m/sec. if any of these variables are changed, the detection distance will also resultantly change. Time setting The light can be set to stay ON for any period of time between approx. 10sec (dial turned fully anti-clockwise) and a maximum of 30min(dial turned fully clockwise). Any movement detected during the “on” time will reset the timer. The LED indica10sec~30min tor will flash when adjusting the time setting dial. The number of flashes means the following: flash = 10sec, 2 flashes= 1 min, 3 flashes= 2 min, 4 flashes= 5 min, 5 flashes=8 min, 6 flashes=10 min, 7 flashes=15 min, 8 flashes=20 min, 9 flashes=25 min, 10 flashes=30 min. NOTE: After the light switches off, it takes approx. 1sec before it is able to start detecting movement again. The light will only switch on in response to movement once this period has elapsed. Light-control setting 2~2000LUX The chosen light response threshold can be infinitely from approx. 2-2000lux. Turn it fully anti-clockwise to select dusk- to-dawn operation at about 2 Lux. Turn it fully clockwise to select daylight operation at about 2000lux. The knob must be turned fully clockwise when adjusting the detection zone and performing the walk test in daylight. Troubleshooting Malfunction The load will not work The load work always Cause Remedy • Wrong light-control setting selected • Adjust setting • Load faulty • Change load • Mains switch OFF • Switch ON • Continuous movement in the detection zone • Check zone setting • The sensor not mounted for detecting movement reliably • Securely mount enclosure The load work without any identifiable move- • Movement occurred, but not identified by the sensor ment (movement behind wall, movement of a small object in immediate lamp vicinity etc.) The load will not work despite movement • Rapid movements are being suppressed to minimize malfunctioning or the detection zone you have set is too small • Check zone setting • Check zone setting ">

Public link updated
The public link to your chat has been updated.
Advertisement