Instruction Manual

ELECTRIC ORDER PICKER

Note: The Owner/Operator must read carefully and understand

all the information presented here before operation.

- 0 -

Content

1. Lifting & Lowering the table………………………… 2

2. Loading Safety Valve ……………………………….. 2

3. Loading Capacity Chart…………………………….. 2

5. Electric Circuit Diagram…………………………….. 4

6. Exploded View & Part List….………………………. 5

- 1 -

THANK YOU FOR USING THIS ELECTRIC ORDER PICKER. FOR

YOUR SAFETY AND CORRECT OPERATION, PLEASE

CAREFULLY READ THIS INSTRUCTION BEFORE USING IT.

NOTE:

All of the information reported herein is based on data available at the moment of printing. The factory reserves the right to modify its own products at any moment without notice and incurring in any sanction. So it is suggested to always verify possible updates.

1. LIFTING & LOWERING THE TABLE

To lift the table, push the TWO 'UP' buttons at both left and right handles at the same time.

To lower the table, push the TWO 'DOWN' buttons at both left and right handles at the same time.

2. LOADING SAFETY VALVE

If the table is overloaded, loading safety valve is automatic opened to stop lifting.

CAUTION! The max. loading capacity is

200Kg (=440LBS)include operator.

3. LOADING CAPACITY CHART

200

60

600 300

LOAD CENTRE (mm)

- 2 -

— The max. loading capacity is 200Kg including operator. Do not overload.

— Before lifting or lowering the table, make sure to brake the picker.

— Before moving the picker, make sure that the table be set at lower position.

— Ensure the balance of loading. Do not load partially or concentrically.

— Store the picker indoor and keep away from rain, water, or acid before storing the picker, turn off the switch.

— Rusted or damaged chain may cause breaking off. Stop operating and replace it.

— Remove load from the table and use safe stopper to prevent the table lowering when service the lift table.

Ride on the table properly and close the door before lifting

CAUTION!

If operating the picker improperly, a person may be injured. Operate properly according to following instruction.

— Do not use the picker on a sloping or soft ground.

— Do not enter underneath the table.

— Do not ride on the table

CAUTION! The max. loading capacity is 200Kg

(=440LBS)include operator.

- 3 -

4. BATTERY RECHARGE

CAUTION! When recharging the battery, keep away from fire. The first recharge time must be more than 10 hours .

CAUTION! When the voltage is reduced to 10.5 volt, the battery must be recharged immediately.

5. ELECTRIC CIRCUIT DIAGRAM

- 4 -

6. EXPLODED VIEW & PART LIST

- 5 -

No. Description Qty No.

1 Cushion

Description Qty

1 25 Spring Washer 12 8

2 Spring 2 26 Roller 8

3 Safety Handrail

4 Handle

5 Pin Axle

2 27 Roller axle

2 29 Right Angle Joint

6 Spacing Retainer 12

7 Pushbutton

4 30 Oil hose

4 31 Right angle Joint

8 Pushbutton 2 32 Battery

9 Pushbutton Case 2 33 Power unit pack

1 34 Charger

11 Platform

12 Locknut M8

13 Washer 8

14 Spring Washer 8

16

17

18 Washer 8

19 Locknut M8

20 Fixed plate

21 Wheel

22

Bolt M8×30

Spring Washer 8

Bearing

4

4

4

4 39 Base

16 40 Power Unit Base

16 41 Nut 6

16

16

36

37

38

42

43

Washer 10

Spring Washer 10

Bolt M10×20

Spring Washer 6

Washer 6

4 44 Screw M6

4 45

Frame of Universal

Wheel

4 46 Pin of wheel

4

4

4

4

4

1

2

2

2

2

1

1

4

8

1

1

1

1

1

1

- 6 -

49 Nut M20

50 Bolt of pole

51 Spring washer 14

52 Nut M6×70

53 Brake spring board

54 Nut M6

55 Pin axle wheel

2

2

2

2

8 47 Bearing

8 48 Wheel

2

4

4

62

63

64

Nut 12

Brake Pole

Connecting Pole

65 Support Pole

66 Thin Nut M10

67 Nut M10

68 Screw M10

2 69 Chain

57

Frame of Universal

Wheel

58 Thin Nut M20 2 71 Chain wheel base

1

1

1

1

1

59 Brake Pole for recovery 1

60 Spring Washer 12

72 Chain wheel

2 73 Chain wheel axle

2 74

Spacing retainer

12

2

2

2

2

2

4

4

2

2

1

- 7 -

Minimum platform height: 26.4"

Maximum platform height: 59"

Minimum operator's platform height: 11 13/16"

Maximum operator's platform height: 44 1/2"