Audio Authority | 1388 | Operating instructions | Audio Authority 1388 Operating instructions

0386.QXD
7/27/01 16:28
Page 1
Operating Instructions
CT-1388YD
CT-1389VYD
CT-2088YD
CT-2089VYD
CT-2788YD
CT-2789VYD
IMPORTANT INFORMATION
Important:
Changes or modification not expressly
approved by Matsushita Television
Company, Inc. could void the user ’s
authority to operate the equipment.
Notice from the FCC:
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
CT-1389VYD
CT-2088YD
CT-2089VYD
CT-2788YD
CT-2789VYD
MODELS
CT-1388YD
FEATURE CHART
FEATURES
Bilingual menu E/S
181 Channels
Closed Captioning
V-Chip Program Lock
Remote (TV only)
ControlPanelLock
Auto Power On Menu
Stereo
Bass/Treble/Balance
SAP
AI sound
Surround Sound
Variable Audio Out
Fixed Audio Out
Earphone jack
-2-
INSTALLATION
Your new TV Monitor/Receiver features a solid state
chassis that is designed to give you many years of
enjoyment. It was thoroughly tested and tuned at the
factory for best performance.
Television Location
Customer Record
Product registration is available for U.S. customers at:
www.prodreg.com/panasonic
Optional Cable Connections
Care and Cleaning
Screen (Turn TV Off)
•
•
Use a mild soap solution or window
cleaner with a soft clean cloth. DO NOT
USE ABRASIVE CLEANERS.
Avoid excessive moisture and wipe dry.
•
•
Use a soft cloth dampened with water or a
mild detergent solution.
Do not use
benzene, thinner, or other petroleum
based cleaners.
Wipe dry with a soft clean cloth. Avoid
excessive moisture.
Specifications
120V AC,
60Hz
VHF-12;
UHF-56;
Cable-113
1 Video Input Jack
(CT-2788YD and CT-2789VYD)
3 Video Input Jacks
(CT-1388YD,CT-1389VYD.
CT-2088YD and CT-2089VYD)
1Vp-p,
75 Ohm,
BNC Jack
Type
1 (set) Audio Input Jack
(CT-2788YD and CT-2789VYD)
3 Audio Input Jacks
(CT-1388YD, CT-1389VYD,
CT-2088YD and CT-2089VYD)
500mV RMS
47K Ohm
Phono Jack
Type
Channel Capability - 181
1 (set) Audio Output Jack
(CT-2788YD and CT-2789VYD)
3 Audio Output Jacks
(CT-1388YD, CT-1389VYD,
CT-2088YD and CT-2089VYD)
Batteries
•
•
•
Replace batteries in pairs.
Do not mix battery types (zinc carbon with
alkaline).
Do not recharge, short-circuit, disassemble,
heat, or burn used batteries.
Cable / Antenna
For proper reception, either a cable or antenna
connection are required.
Cable Connection
Connect the cable supplied by your local
cable company.
BNC Jack
Type
Incoming Cable from Cable Company
Phono Jack
Type
Video Monitor Output Jack
BNC Jack
Type
Audio Monitor Output Jack
Phono Jack
Type
S-Video In/Out Jacks
Y-C
Connector
Earphone Jack
(CT-1388YD and CT-1389VYD)
1/8” mini
plug Type
75 Ohms VHF/UHF
on back of TV
Note:
Specifications are subject to change without notice
or obligation.
-3-
A cable converter box may be required for
proper reception. Check with your local
Cable
company
for
compatibility
requirements.
CABLE/ANTENNA
1 Video Output Jack
(CT-2788YD and CT-2789VYD)
3 Video Output Jacks
(CT-1388YD, CT-1389VYD,
CT-2088YD and CT-2089VYD)
This product is equipped with
a three-wire ground type plug a plug with two blades and a 3 Wire Ground plug
third pin which is round. This
plug will only fit into a
grounding type outlet. This is a safety feature. If you
are unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet. DO
NOT DEFEAT THE SAFETY PURPOSE OF THE
GROUNDING TYPE PLUG.
INSTALLATION
(CT-1389VYD, CT-2089VYD and
CT-2789VYD only)
CAUTION: MAKE SURE PLUG
IS INSERTED FULLY INTO
RECEPTACLE.
SPECIFICATIONS
Power Source
CT-1388YD, CT-1389VYD (0.9A)
CT-2088YD, CT-2089VYD (1.3A)
CT-2788YD, CT-2789VYD (1.8A)
AC Power Supply Cord
CARE AND CLEANING
Cabinet and Remote Control
Shielded audio and video cables should be used
between components. For best results:
•
Use 75-ohm coaxial shielded cables.
•
Use appropriate input and output
connectors that match your component
connectors.
•
Avoid
long
cables
to
minimize
interference.
CONGRATULATIONS
Model
Number
Serial
Number
FEATURE CHART
The model and serial number of this product may be
found on the back of the unit. You should note the
model and serial number in the space provided and
retain as a permanent record of your purchase. This
will aid in identification in the event of theft or loss.
This unit is intended to be used with an
entertainment center. Consult your dealer for
available options.
Avoid excessive sunlight or bright lights,
including reflections.
Keep away from excessive heat or moisture.
Inadequate ventilation may cause internal
component failure.
Fluorescent lighting may reduce Remote
Control transmitting range.
Avoid magnetic equipment, including motors,
fans, or external speakers.
IMPORTANT INFORMATION
CONGRATULATIONS
Cable / Antenna (Cont.)
Antenna Connection
•
•
For proper reception of VHF/UHF channels, an
external antenna is required. For best reception
an outdoor antenna is recommended.
Antenna Mode must be set to TV.
Incoming Cable from Home Antenna
Note:
Cable mode is preset at the factory. Antenna users must change to antenna mode in Set Up menu.
OPTIONAL EQUIPMENT CONNECTION
Video/Audio In & Out Connection
CT-1388YD, CT-1389VYD, CT-2088YD and CT-2089VYD
The IN and OUT terminals located on the back of Monitor directly pass the input signals through
the out terminals, so you may monitor or record the external Video/Audio information.
Operation
1.
2.
3.
Connect an external Video/Audio source to VIDEO 1, VIDEO 2 or VIDEO 3 IN terminals, as
shown.
Select the same video mode that the equipment is connected to, by pressing the
TV/VIDEO or VIDEO SELECT button.
Connect a Monitor or VCR to the Video/Audio out terminals as shown. The out terminals
will provide the same signals as the input terminals for monitoring or recording.
Note:
Video/Audio 1, 2 and 3 input and output terminals will operate whether the Monitor is ON or OFF.
VIDEO 3
VIDEO 2
AUDIO
IN
AUTO 75
Ω
AUDIO
/HIGH
AUTO 75
Ω
MONITOR OUT
VIDEO 1
AUDIO
/HIGH
AUTO 75
Ω
AUDIO
/HIGH
S-VIDEO
IN
OUT
IN
OUT
IN
OUT
VIDEO
OUT
VIDEO
VIDEO
VIDEO
Monitor
VCR
OR
External Audio/Video Equipment
-4-
CT-1388YD, CT-1389VYD, CT-2088YD and CT-2089VYD
The S-Video IN and OUT terminals located on the back of Monitor directly pass the input signals
through the out terminals, so you may monitor or record the external video/audio information.
Notes:
•
•
•
Only Video 3 audio in and out may be used with S-Video operation.
Connection of optional S-Video jack will override the standard Video Input 3 BNC connector.
S-Video IN and OUT terminals will operate whether the Monitor is ON or OFF.
Operation
1.
2.
3.
4.
5.
6.
Connect S -VIDEO input to a external audio/video source as shown.
Connect video 3 audio in jack as shown.
Press the TV/VIDEO or VIDEO SELECT button to select video 3 mode.
Connect S -VIDEO out to a monitor or VCR as shown.
Connect video 3 audio out jack as shown.
The output terminals will provide the same signals as the input terminals for monitoring or
recording.
VIDEO 2
AUDIO
IN
AUTO 75
Ω
VIDEO 1
AUDIO
/HIGH
AUTO 75
Ω
MONITOR OUT
AUDIO
/HIGH
AUTO 75
Ω
AUDIO
/HIGH
S-VIDEO
IN
OUT
IN
OUT
IN
OUT
VIDEO
OUT
VIDEO
VIDEO
VIDEO
Monitor
Monitor
VCR
OR
Monitor Out Connection
The Monitor out terminals will output video and audio signals being displayed onsrceen.
Connect the Monitor out terminals as shown above for models CT-1388VD, CT-1389VYD,
CT-2088VD, and CT-2089VYD. Connect the Monitor Out terminals as shown below for models
CT-2788YD and CT-2789VYD.
Note:
The Monitor Out terminals only operate when the monitor is on.
MONITOR OUT
OUTPUT
INPUT
IN
R
AUDIO
L
R
AUDIO
L
R
AUDIO
L
S-VIDEO
OUT
VIDEO
AUTO 75
VIDEO
Ω
OR
Monitor
VCR
-5-
/HIGH
AUTO 75
VIDEO
Ω
OPTIONAL EQUIPMENT CONNECTIONS
External Audio/Video Equipment
VIDEO 3
CABLE/ANTENNA CONT. VHF/UHF ANTENNA
S-Video In & Out Connection
/HIGH
AUTO 75
Ω
/HIGH
Video/Audio In & Out Connection
CT-2788YD and CT-2789VYD
The IN and OUT terminals located on the back of Monitor directly pass the input signals through the out
terminals, so you may monitor or record the external video/audio information.
Operation
1.
2.
3.
4.
Connect an external video/audio source to the Monitor video/audio input terminals as shown.
Select video mode by pressing the TV/VIDEO button.
Connect an external video/audio source (Monitor or VCR) to the video/audio
output terminals as shown.
The output terminals will provide the same signals as the input terminals for monitoring or
recording.
Note:
Video/Audio IN and OUT terminals will operate whether the Monitor is ON or OFF.
MONITOR OUT
OUTPUT
INPUT
IN
R
L
AUDIO
L
AUDIO
R
R
L
AUDIO
S-VIDEO
OUT
VIDEO
AUTO 75
Monitor
VIDEO
Ω
/HIGH
AUTO 75
VIDEO
Ω
/HIGH
AUTO 75
Ω
/HIGH
VCR
OR
External Audio/Video Equipment
S-Video In & Out Connection
CT-2788YD and CT-2789VYD
The IN and OUT terminals located on the back of Monitor directly pass the input signals through the out
terminals, so you may monitor or record the external video/audio information.
Note:
•
Video/Audio IN and OUT terminals will operate whether the Monitor is ON or OFF.
S-Video connection is optional and overrides the standard Video connection when connected.
Operation
1.
2.
3.
4.
Connect an external video/audio source to the Monitor Input terminals as shown.
Select video mode by pressing the TV/VIDEO button.
Connect audio output to external video/audio source (Monitor or VCR) terminals as shown.
The output terminals will provide the same signals as the input terminals for monitoring or
recording.
External Audio/Video Equipment
MONITOR OUT
OUTPUT
INPUT
IN
R
AUDIO
L
R
AUDIO
L
R
AUDIO
L
S-VIDEO
OUT
VIDEO
AUTO 75
VIDEO
Ω
/HIGH
OR
Monitor
VCR
-6-
AUTO 75
VIDEO
Ω
/HIGH
AUTO 75
Ω
/HIGH
This Monitor has an Auto Power On feature which automatically turns the unit ON when AC power is
supplied. This feature initiates the Monitor to turn On automatically when using it with other equipment to a
main power switch. (Such as: AC power strip or when plugged directly into the back of another video
equipment.) Once the initial power has been supplied and the Monitor turns ON, the POWER switch
located on the front of the Monitor may be used to turn the Monitor OFF and ON as desired.
on
off
Monitor AC Plug
Procedure
SET UP
IDIOMA/
LANGUE
PROG CHAN
CC
AUTO POWER ON
OFF
OTHER ADJ.
4.
5.
6.
Press
button to highlight OTHER ADJ.
Press
button to highlight AUTO POWER ON.
Press VOL
button to select SET or OFF.
Note:
When this feature is activated (on), the Timer features will be disabled.
CONTROL PANEL LOCK FEATURE
Procedure
With the Monitor turned on, press the ACTION and VOL RIGHT ( )buttons on the control panel
simultaneously, then quickly press the ACTION and UP ( ) buttons simultaneously. This will activate the
Keyboard Lock feature. To deactivate repeat procedure.
Note:
There will be no onscreen display.
To confirm if the Control Panel Lock feature is activated, press any button other than the POWER button
(the Power button is never disabled).
-7-
CONTROL PANEL LOCK FEATURE
Press Action button.
Press CH / and VOL / buttons to highlight the Set-up Icon.
Press Action button to display Set-up menu.
AUTO POWER ON FEATURE
AC Power Strip
1.
2.
3.
OPTIONAL EQUIPMENT CONNECTIONS CONT.
AUTO POWER ON FEATURE
PANASONIC BROADCAST AND TELEVISION SYSTEMS COMPANY
Panasonic®
BROADCAST AND TELEVISION SYSTEMS
PANASONIC BROADCAST AND TELEVISION SYSTEMS COMPANY
Division of Matsushita Electric Corporation of America
3330 Cahuenga Boulevard West, Los Angeles, CA 90068
WARNING
RISK OF ELECTRIC
SHOCK DO NOT OPEN
WARNING: To reduce the risk of electric shock do not
remove cover or back. No user-serviceable parts inside.
Refer servicing to qualified service personnel.
The exclamation point
within a triangle is intended
to tell the user that
important operating and
servicing instructions are in
the papers with the
appliance.
SAFETY WARNING
The lightning flash with
arrow head within a
triangle is intended to
tell the user that parts
inside the product are
a risk of electric shock
to persons.
WARNING: To prevent fire or shock hazard, do not
expose this appliance to rain or moisture.
FCC NOTE:
This unit has been tested and found to comply with limits for a class B digital device unit, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Read these instructions completely before operating TV.
Contents are subject to change without notice or obligation.
Copyright 2001 by Matsushita Electric Corporation of America. All rights reserved.
Unauthorized copying and distribution is a violation of law.
PRINTED IN USA
TQB2AA0386
010905
CH / VOL Buttons
MAIN MENU
Press the CH (channel) or VOL (volume)
buttons to select an icon. Use the CH buttons
to highlight the desired features. Use VOL
buttons to select and adjust features.
ACTION Button
Press the ACTION button to display the Main
Menu and Sub Menus. Press the ACTION
button repeatedly to exit.
Note:
Remote Navigation Buttons
CH
Models CT-1388YD and CT-2088YD do
not display AUDIO, CHANNELS or
LOCK icons in the Main Menu. Models
CT-1389VYD and CT-2089VYD do not
display AUDIO icon. Model CT-2788YD
does not display CHANNELS or LOCK
icons.
VOL
VOL
CH
Main Menu
Remote Control
The Remote Control Quick Reference Guide
is located in the package provided with the
TV.
MAIN MENU FEATURE CHART
MENU
DESCRIPTION
SET UP
IDIOMA/
LANGUE
PROG CHAN
Select English or Español (Spanish) menu.
MODE - Select Cable or TV.
AUTO PROGRAM - Automatically program
channels having a signal into memory.
MANUAL PROGRAM - Manually add or delete
channels from memory.
CC MODE - Select C1 or C2 for Closed
Captioning display. Select OFF to display
closed captioning when MUTE button is
pressed.
CC MODE
AUTO POWER ON - Automatically turns the
unit ON when AC power is supplied.
OTHER ADJ.
Note:
When this feature is activated (on), the Timer
features will be disabled.
AUDIO
(CT-2788YD and
CT-2789VYD only)
MODE for:
•
STEREO - Two channel audio reception.
•
SAP - (Second Audio Program) Tune to
the alternate audio channel if available in
your area (bilingual or descriptive audio).
Note:
AUDIO ADJ.
SAP is not available in CT-2788YD.
•
MONO - One channel audio. Use when
stereo signal is weak.
BASS - Increase or decrease the bass
response.
TREBLE - Increase or decrease the treble response.
BALANCE - Emphasize the left/right speaker volume.
NORMAL - Reset BASS, TREBLE, and BALANCE to
factory default.
-9-
MENU
DESCRIPTION
AI SOUND - Automatically maintain constant
volume between programs and commercials.
(AI sound is not available in VIDEO mode.)
OTHER ADJ.
Note:
SURROUND
SPEAKERS
AI Sound feature is not available in
CT-2788YD)
MODE - Enhances audio response when listing
to stereo.
ON - TV SPEAKERS operate normally.
OFF&VARIABLE AUDIO OUT - TV Speakers
OFF, sound is adjustable from TV.
OFF&FIXED AUDIO OUT- TV Speakers OFF,
sound is adjustable from External Amplifier.
Note:
OFF & VARIABLE and OFF & FIXED AUDIO
OUT features available on model CT-2789VYD
only.
CHANNELS
CHANNEL CAPTION
MANUAL CAPTION - Provide labels for up to
30 stations using up to four characters for each
station.
TIMER
CLOCK SET
SLEEP TIMER
PROGRAM TIMER
When entered, TIME will display on screen after
pressing POWER button, RECALL button, or
changing channels.
Set timer to turn off television in 30, 60 or
90 minutes. Select NO to turn timer off.
Program TV to automatically turn on and off at
selected time on a selected channel, daily or
only one day.
PICTURE
VIDEO ADJ.
COLOR - Adjust desired color intensity.
TINT - Adjust natural flesh tones
BRIGHTNESS - Adjust dark areas for crisp
detail.
PICTURE - Adjust white areas of picture.
SHARPNESS - Adjust clarity of outline detail.
NORMAL - Reset all picture adjustments to
factory default settings.
LOCK
LOCK MODE
Program to prevent video games and VCR’s
from being viewed.
Note:
For information about Motion Picture Status and
TV Parental Status, see the V-CHIP Parental
Lock manual provided with the TV package.
- 10 -
REMOTE CONTROL MAIN MENU FEATURE CHART
MAIN MENU
MAIN MENU FEATURE CHART CONT.
SPECIAL FEATURES
Channels
Manual Caption
Languages
Program channel captions (station labels) for 30
stations using up to four characters.
In SET UP menu, select ENGLISH or ESPAÑOL.
SET UP
MODE
IDIOMA/
LANGUE
CHANNELS
MANUAL CAPTION
ENGLISH
ENTER CHANNEL
3
ENTER CAPTION
PROG CHAN
----
TOMOVE CURSOR TO SELECT CHANNEL CC
OTHER ADJ.
Note:
Timer
Delete channel captions by entering
spaces in all four character slots.
Sleep Timer
In TIMER menu, program to turn TV OFF in 30, 60,
or 90 minutes. Select NO to turn off timer.
LOCK
Lock Mode (Lock and Unlock)
TIMER
CLOCK SET
SLEEP
(For models CT-1389VYD, CT-2089VYD and CT2789VYD only.)
HOW LONG?
30
Select LOCK MODE to prevent video games and
VCR’s from being viewed.
Lock Channel 3, Channel 4, and Video Inputs for
12, 24, 48 hours or ALWAYS by entering a four
digit secret code, then selecting GAME.
TIMER
Note:
Program Timer
In Timer menu, program TV to automatically turn
on and off at selected time on a selected channel,
daily or one day.
Unlock LOCK SET by reentering your four digit
secret code, then selecting LOCK MODE OFF.
TIMER
CLOCK SET
SLEEP
TIMER
Note:
Understand how to unlock LOCK MODE
before using it. Use a code that is easy
to remember or record it in a safe place.
LOCK
MODE
ONE DAY
ON TIME
--:-OFF TIME
--:-ENTER CHANNEL
3
LOCK SET
SET TIME FIRST
HOW LONG?
TIME must be entered in the TIMER
menu to operate PROGRAM TIMER.
Note:
Helpful Hints: PROGRAM TIMER
Activation
U.S. MOVIES
STATUS
OFF
ENTER CODE
---FIRST
When LOCK MODE is ON, and if CH. 3,
CH. 4 or Video Inputs is selected, the
message PG displays in the upper left
corner of the TV screen.
Helpful Hints: LOCK MODE Unlock
The PROGRAM TIMER is active when the TV is
OFF or ON. The TV will switch to the selected
channel at the selected time set by the
PROGRAM TIMER.
If you do not remember your code, the LOCK will
unlock in 12, 24, or 48 hours depending on last
setup. Be cautious when selecting ALWAYS. If
ALWAYS is selected and you forget your secret
code, the TV must be serviced by a qualified
technician in order to clear the LOCK options
that are set.
Helpful Hints: Turn Off After 90
Minutes
The TV automatically turns OFF after 90
minutes when turned on by the PROGRAM
TIMER. If the OFF time is programmed or if a
key is pressed, the automatic OFF after 90
minutes will be cancelled.
OFF
BLOCK PROGRAMS:
MODE
* For more information about Block Programs,
see the V-CHIP Parental Lock manual provided
with the TV package.
- 11 -
TROUBLESHOOTING / L OCALIZACIÓN DE F
Before you call for service, determine the symptoms and make a few simple checks shown below.
AUDIO
VIDEO
Solutions
- Equipment Connected to Input Connections
Noisy Sound
Snowy Video
- Antenna Location and/or Connection
- Electrical Appliances, Lights, Cars, and
Trucks
Noisy Sound
Interference
- Video Input Connector Seated Properly
- Increase Volume
- Check TV SPEAKERS on/off
No Sound
- Change Channel
Normal Picture
- Audio Input Connector Seated Properly
- Set TV or Cable Mode Properly
- Check Antenna Cables
No Picture
No Picture
- Adjust Color Settings
- Change Channel
Normal Sound
No Color
- Check Audio is set to Stereo or Mono, not
SAP (If Applicable)
Wrong Sound
Normal Picture
VIDEO
- Monitor/Receiver in Video Mode with no
signal
No Sound
Black Picture
- Replace Remote Control Batteries
Normal Picture
Normal Sound
Intermittent Remote Control Operation
- 12 -
TROUBLESHOOTING CHART
?
No Sound
- Check Power Cord is Plugged into Active
Outlet
- Adjust Brightness and Audio Controls
- Change Channel
- Check Cable Connections
- Program the Remote Control Again
- Check Second Video Source Operation
LOCK
No Sound
CHANNEL CAPTION
- Check Mute
TIMER
- Diathermy and Medical Equipment
LANGUAGES
- Input Connectors Seated Properly
SPECIAL FEATURES
TROUBLESHOOTING CHART
Download PDF