Volvo S40 2005 Owners Manual

Volvo S40 2005 Owners Manual
2005
VOLVO
S40
6968
TP 7459 (English). AT 0446. Printed in Sweden, Elanders Infologistics Väst AB, Mölnlycke 2004
OWNE R'S MANUAL VOLVO S40
TP 7459
WEB EDITION
2005
Introduction
Dear Volvo owner
We hope you will enjoy many years of driving pleasure in your Volvo. The car has been designed for the safety and comfort of you and your
passengers. Volvo is one of the safest cars in the world. Your Volvo has also been designed to satisfy all current safety and environmental
requirements.
In order to increase your enjoyment of the car, we recommend that you familiarise yourself with the equipment, instructions and maintenance
information contained in this owner’s manual.
Thank you for choosing Volvo!
N
Introduction
Owner’s Manual
A good way of getting to know your new car
is to read the owner’s manual, ideally before
your first journey. This will give you the opportunity to familiarise yourself with new functions, to see how best to handle the car in different situations, and to make the best use of
all the car’s features. Please pay attention to
the safety instructions contained in the
manual:
WARNING!
"Warning!" texts indicate where there is a
risk of personal injury in the event of the
instructions not being followed.
Important!
"Important!" texts indicate a risk of
damage to the car in the event of the
instructions not being followed.
The equipment described in the owner’s
manual is not present in all models. In addition to standard equipment, this manual also
describes options (factory fitted equipment)
and certain accessories (extra equipment).
NOTE! Volvo cars are adapted for the varying
requirements of different markets, as well as
O
for national or local legal requirements and
regulations.
The specifications, design features and illustrations in this owner’s manual are not binding. We reserve the right to make modifications without prior notice.
© Volvo Car Corporation
Volvo Cars and the environment
Volvo Cars and the environment
Our environmental philosophy
Clean inside and out
Quality, Safety and Environmental care are
the three core values which guide all the
activities of Volvo Cars. Volvo cars comply
with strict international environmental standards and are manufactured in some of the
cleanest and most resource-efficient plants in
the world. Volvo Cars has been awarded
multi-site global certification under the
ISO 14001 environmental standard, ensuring continuous improvement in the area. All
Volvo models are supplied with an environmental product declaration - or EPD - which
enables the customer to compare the environmental performance of different models
and engines. Visit epd.volvocars.se for more
information.
Your Volvo is designed to be clean inside and
out, a concept which means that you benefit
in two ways - from a clean cabin and a highly
efficient exhaust treatment system, which
ensures that your car saves fuel and releases
a minimum of harmful substances.
Inside, the air entering the passenger compartment is filtered to protect you and your
passengers from dust, particles and pollen.
A sophisticated air quality system known as
IAQS1 can be added as an option to ensure
that the air supplied to the passenger compartment is cleaner than the air outside. Consisting of an electronic sensor and an activated carbon filter, the system monitors the
1.
Interior Air Quality System
level of carbon monoxide in the incoming air
and closes the air intakes to prevent the level
in the cabin from becoming too high - for
example in heavy city traffic, tailbacks and
tunnels - while the carbon filter traps nitrogen
oxides, ground-level ozone and hydrocarbons. In addition, to benefit allergy sufferers,
the fabrics used in the interior comply with
the provisions of the international Öko-Tex2
standard. Outside, a special catalytic coating
known as PremAir®3 is used to convert harmful ground-level ozone in the air passing
through the radiator into pure oxygen.
2.
3.
An international ecological standard
for textiles
Applies only to five-cylinder engines
PremAir® is a registered trademark
of Engelhard Corporation
P
Volvo Cars and the environment
Volvo Cars and the environment
A Volvo meets strict international environmental demands and delivers low fuel consumption to reduce emissions of greenhouse
carbon dioxide. In terms of fuel economy,
Volvo cars are highly competitive in their
respective segments.
Volvo workshops and the
environment
Regular maintenance carried out by an
authorised Volvo workshop creates the conditions for low fuel consumption and contributes to a cleaner environment. Volvo service
technicians are equipped with the knowhow
and tools to ensure that your car delivers the
best possible environmental performance.
Reducing environmental impact
We believe that our customers share our
concern for the environment. You can contribute to improving the environment by using
only ecologically approved car care products,
and by ensuring that your car is serviced and
maintained according to the instructions in
the owner's manual.
The following hints will help you to do your bit
for the environment:
• Always ensure that your tyre pressures
are correct. Poorly inflated tyres increase
fuel consumption.
Q
• Since roof racks and ski
boxes increase air
resistance, leading to
significantly higher fuel
consumption, they
should be removed
immediately after use.
• Remove unnecessary items from the car the greater the load the higher the fuel
consumption.
• Is your car equipped with an engine block
heater? If so, use it for a few hours before
starting from cold to reduce fuel consumption and exhaust emissions.
• Drive gently! Avoid accelerating and braking too hard.
• Drive in the highest possible gear - lower engine
revs reduce fuel consumption.
• Ease back on the accelerator on downhill gradients.
• Use engine braking. Take your foot off the
accelerator and change down.
• Avoid idling. Switch off the engine in traffic queues.
• Always dispose of environmentally hazardous
waste, such as batteries and oils, in an environmentally safe manner. If uncertain, ask
your authorised Volvo workshop for
advice.
• Service your car regularly.
These hints will help you to reduce your fuel
consumption without increasing your travel
time or lessening the enjoyment of driving.
Apart from being kind to your car, you'll be
saving money - and the Earth's resources.
Contents
Instrument overview
Safety
Instruments and controls
Climate control
Interior
Locks and alarm
Starting and driving
Wheels and tyres
Car care
Maintenance and service
Infotainment system
Technical data
7
13
37
65
77
87
99
131
149
155
179
207
R
S
Instrument overview
Overview, left-hand drive car
Overview, right-hand drive car
Driver’s door control panel
8
10
12
T
Instrument overview
Overview, left-hand drive car
Left-hand drive
U
Instrument overview
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
Steering wheel adjustment
Bonnet release
Control panel
Direction indicators, main beam, trip
computer
Lighting, fuel filler flap opener
Door handle, central locking
Air vents in dashboard
Air vent for side window
Cruise control
Horn, airbag
Combined instrument panel
Keypad for infotainment system
Windscreen wipers and washers,
headlamp washers
Ignition switch
Interior rearview mirror
Seatbelt reminder
Interior lighting for left-hand side
Deactivation of alarm detectors,
deadlocks
Switch for interior lighting
Position of accessory switch
Interior lighting for right-hand side
Sunroof controls
Display for climate control and
infotainment system
Infotainment system
25. Controls for climate control,
infotainment system and personal
preferences
26. Climate control
27. Gear lever
28. Hazard warning flashers
29. Door handle
30. Glovebox
31. Parking brake
32. Electrical socket/cigarette lighter
33. STC or DSTC stability system
34. Switch, optional equipment
V
Instrument overview
Overview, right-hand drive car
Right-hand drive
NM
Instrument overview
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
Switch for retrofitted accessory
STC or DSTC stability system
Electrical socket, cigarette lighter
Parking brake
Control panel
Glovebox
Door handle
Air vent for side window
Air vents in dashboard
Gear lever
Climate control
Controls for climate control,
infotainment system and personal
preferences
Infotainment system
Display for climate control and
infotainment system
Sunroof controls
Interior lighting for left-hand side
Deactivation of alarm detectors,
deadlocks
Switch for interior lighting
Switch for retrofitted accessory
Interior lighting for right-hand side
Seatbelt reminder
Interior rearview mirror
Ignition switch
Windscreen wipers and washers,
headlamp washers
25.
26.
27.
28.
29.
30.
31.
32.
Cruise control
Combined instrument panel
Horn, airbag
Keypad for infotainment system
Hazard warning flashers
Door handle, central locking
Lighting, fuel filler flap opener
Direction indicators, main beam, trip
computer
33. Bonnet release
34. Steering wheel adjustment
NN
Instrument overview
Driver’s door control panel
1.
2.
3.
4.
5.
NO
Blocking switch for rear power windows
(standard)
Electric child locks (option)
Power windows
Door mirror, left-hand side
Door mirrors, setting
Door mirror, right-hand side
Safety
Seatbelts
Airbags (SRS)
Activating/deactivating the airbag (SRS)
Side airbags (SIPS)
Inflatable Curtain (IC)
WHIPS
When are the safety systems activated?
Crash mode
Inspecting the airbags and inflatable curtains
Child safety
14
17
20
22
24
25
27
28
29
30
NP
Safety
Seatbelts
Releasing the belt:
– Press the red lock button and let the belt
retract. If the belt does not retract fully,
feed the belt in by hand so that it does not
hang lose.
The belt locks and cannot be withdrawn:
Tensioning the hip strap. The belt must be
positioned low down.
• if it is pulled out too quickly.
• during braking and acceleration.
• if the car leans heavily.
It is important that the belt lies against the
body so it can provide maximum protection.
Do not lean the backrest too far back. The
seatbelt is designed to protect in a normal
seating position.
Always use a seatbelt
Keep the following in mind:
Heavy braking can have serious consequences if the seatbelts are not used. Ensure
that all passengers use their seatbelts.
Otherwise, rear seat passengers may be
thrown forward against the backs of the front
seats in a collision.
• do not use clips or anything else that can
prevent the belt from fitting properly.
• ensure the belt is not be twisted or
caught on anything.
• the hip strap must be positioned low
down (not over the abdomen).
• tension the hip strap over the lap by
pulling the diagonal shoulder belt as
illustrated.
Putting on a seatbelt:
– Pull the belt out slowly and secure it by
pressing the buckle into the lock. A loud
"click" indicates that the belt has locked.
NQ
WARNING!
The seatbelts and airbags interact. If a
seatbelt is not used or is used incorrectly,
this may diminish the protection provided
by the airbag in the event of a collision.
WARNING!
Each belt is intended for one person only.
WARNING!
If the belt has been subjected to a major
load, such as in a collision, the entire belt
must be replaced. This includes the reel,
mountings, bolts and buckles. Some of
the protective characteristics of the belt
may have been lost, even if it appears to
be undamaged. Replace the seatbelt if the
belt is worn or damaged. The new
seatbelt must be type-approved and
intended for installation in the same
position as the replaced belt.
Never modify or repair the seatbelts
yourself. Contact an authorised Volvo
workshop.
Safety
reminder is heard that changes frequency
with the speed of the car.
Rear seat
The seatbelt reminder has two sub-functions:
1
Seatbelt reminder
A symbol lights up in the roof console (above
the rearview mirror) as a reminder that the
seatbelts are not buckled up. A symbol also
lights up on the combined instrument panel.
If the car is stationary, the reminder is extinguished after approximately six seconds.
Front seat
The symbols remain lit as long as the driver or
front seat passenger do not have their
seatbelts on. (If a child seat is place on the
front seat, the reminder does not come on.) In
addition to the two symbols, an audible
1.
Function can depend on market
• Notifies of the number of seatbelts being
used via a message on the information
display. This function is automatically
activated as soon as a rear door is
opened and closed, even if no one is
actually sitting in the rear seat. The
message is automatically erased
approx. 10 seconds after the car is driven
away, or can be acknowledged manually
by pressing the READ button.
• Warns that someone in the rear seat has
removed their seatbelt while the car is
moving. A message appears on the information display and an audible warning
sounds. The warning ceases once the
belt has been put back on, or can be
acknowledged manually by pressing the
READ button.
The message on the display that states how
many seatbelts are in use can be viewed at
any time. To read saved messages, press the
READ button.
Seatbelts and pregnancy
It is extremely important that the seatbelt is
used correctly during pregnancy. It should be
in contact with the body. The upper part of
the seatbelt should fit between the breasts
and against the side of the abdomen. The hip
section of the seatbelt must be flat and as far
under the abdomen as possible. It must not
slide up towards the abdomen.
An expectant mother who is driving should
move the seat as far back as possible in order
to obtain the greatest possible distance
between the steering wheel and the
abdomen. Set the steering wheel as far
forward as a comfortable driving position
permits.
NR
Safety
Seatbelts
Seatbelt tensioner
All the seatbelts (except the centre rear belt)
are equipped with belt tensioners. A
mechanism in the belt tensioner tightens the
belt around the body in the event of a sufficiently violent collision. This provides more
effective restraint for passengers.
Label on seatbelts with seatbelt tensioner
NS
Safety
Airbags (SRS)
WARNING!
To minimise the risk of injury if the airbag
deploys, passengers must sit as upright
as possible with their feet on the floor and
backs against the backrest. Seatbelts
must be secured.
WARNING!
Airbag (SRS) on the driver’s
side
The car has an SRS airbag (Supplemental
Restraint System) in the steering wheel to
supplement the protection afforded by the
seatbelt. This airbag is fitted into the centre of
the steering wheel. The steering wheel is
marked SRS AIRBAG.
Passenger airbag (SRS)
The passenger airbag1 is fitted behind a
panel above the glovebox. This panel is
marked SRS AIRBAG.
Never place a child in a child seat or on a
booster cushion in the front seat if the
airbag (SRS) is activated.1
Never allow a child to stand or sit in front
of the front passenger seat. No one
shorter than 140 cm (4 ft 7) should sit in
the front passenger seat if the airbag
(SRS) is activated.
Failure to follow the advice given above
can endanger the life of the child.
1. For information on activated/deactivated
airbag (SRS), see page 20.
WARNING!
The seatbelts and airbags interact. If a
seatbelt is not used or is used incorrectly,
this may diminish the protection provided
by the airbag in the event of a collision.
1.
Not all cars have a passenger airbag
(SRS). This can be unselected when
the car is ordered.
NT
Safety
Airbags (SRS)
WARNING!
If the warning symbol for the AIRBAG
system remains on or comes on while
driving, it means that the AIRBAG
system is not functioning fully. The
symbol can indicate a fault in the
seatbelt buckle, SIPS, SRS or IC
system. Contact an authorised Volvo
workshop immediately.
Location of the passenger airbag in left-hand
drive and right-hand drive cars.
WARNING!
Objects and accessories must not be
positioned or glued on or near the SRS
AIRBAG panel (above the glovebox) or in
the area affected by a deployed airbag.
Never interfere with SRS components in
the steering wheel or the panel above the
glovebox.
NU
Warning symbol on the
combined instrument panel
The AIRBAG system is monitored continuously by the car’s electronic control system.
The warning symbol on the combined
instrument panel lights when the ignition key
is turned to position I, II or III. The symbol
goes out after about six seconds if the
AIRBAG system is working correctly.
As well as the warning symbol,
a message appears on the
information display. If the
warning symbol malfunctions,
the warning triangle comes on
and the message SRS
AIRBAG SERVICE URGENT
appears on the display.
Contact an authorised Volvo workshop
immediately.
Safety
WARNING!
Work on the SRS system can cause
malfunction and result in serious personal
injury.
Repairs must only be performed by an
authorised Volvo workshop.
Airbags (SRS)
NOTE! The airbags have a function whereby
their capacities are adapted to the collision
force to which the vehicle is subjected.
SRS system, left-hand drive
SRS system, right-hand drive
SRS system
NOTE! The sensors react differently
depending on the course of the collision and
whether the seatbelts on the driver and
passenger side are used. It is therefore
possible that only one (or none) of the
airbags may inflate in a collision. The SRS
system senses the force of the collision on
the car and adapts accordingly so that one or
more airbags is deployed.
The SRS system consists of a gas generator
surrounded by an inflatable airbag. A sufficiently violent collision trips sensors and
ignites the gas generator, inflating the airbag
with hot gas. To cushion the impact, the
airbag deflates when compressed. When this
occurs, smoke escapes into the car. This is
completely normal. The entire process,
including inflation and deflation of the airbag,
occurs within tenths of a second.
NV
Safety
Activating/deactivating the airbag (SRS)
WARNING!
Activated airbag (passenger seat):
Never place a child in a child seat or on a
booster cushion in the front passenger
seat. This also applies to persons shorter
than 140 cm (4 ft 7).
Deactivated airbag (passenger seat):
Persons taller than 140 cm (4 ft 7) must
never sit in the passenger seat.
Failure to follow the advice given above
can endanger life.
Indicator showing that the passenger airbag
(SRS) is deactivated.
PACOS (option)
The airbag (SRS) for the front passenger
seat can be deactivated. This is necessary if
a child seat is to be placed there.
Indicator
A text message on the roof panel indicates
that the passenger airbag (SRS) is deactivated.
OM
PACOS (Passenger Airbag Cut-Off Switch)
Activating/deactivating
The switch is located on the passenger end
of the dashboard and is accessible when the
passenger door is open. Check that the
switch is in the required position. Volvo
recommends that that the ignition key is used
to change position. (Other items with a shape
similar to a key can be used.)
WARNING!
If the car is equipped with a front
passenger airbag (SRS), but does not
have PACOS, the airbag will always be
activated.
Safety
WARNING!
Do not allow anyone to sit in the front
passenger seat if the text message in the
roof panel indicates that the airbag (SRS)
is deactivated and the airbag warning
symbol is displayed in the combined
instrument panel. This indicates that there
has been a severe malfunction. Contact
an authorised Volvo workshop as soon as
possible.
Switch for SRS in ON position.
Switch for SRS in OFF position.
Switch position
OFF = Airbag (SRS) is deactivated. With the
switch in this position, children in a child seat
or on a booster cushion can sit in the front
passenger seat, but never persons taller than
140 cm (4 ft 7).
ON = Airbag (SRS) activated. With the
switch in this position, persons taller than
140 cm (4 ft 7) can sit in the front passenger
seat, but never children in a child seat or on a
booster cushion.
ON
Safety
Side airbags (SIPS)
WARNING!
Work on the SIPS bag system can cause
malfunction and result in serious personal
injury. Always contact an authorised Volvo
workshop.
Do not put objects in the area between
the outside of the seat and the door panel,
since this area is required by the side
airbag.
Child seats and side airbags
Side airbag locations.
Side airbags — SIPS bags
A large proportion of the collision force is
transferred by the SIPS to the floor, roof,
beams, pillars, and other structural parts of
the body. The side airbags on the driver and
front passenger seats protect the chest area
and are an important part of the SIPS. The
SIPS bag system consists of two main parts:
The side airbags and the sensors. The side
airbags are located in the front seat
backrests.
WARNING!
Use only Volvo genuine car seat covers, or
seat covers approved by Volvo. Other
seat covers may impede the operation of
the side air bags.
WARNING!
The side airbag does not diminish the
protection provided by the car to children
seated in a child seat or on a booster
cushion.
A child seat or booster cushion can be
placed on the front passenger seat provided
that the car does not have an activated1
passenger airbag.
Side airbags are a supplement to the SIPS
system. Always wear a seatbelt.
Side airbags are a supplement to the
SIPS system. Always wear a seatbelt.
1.
OO
For information on activated/deactivated airbag (SRS), see page 20.
Safety
Left-hand drive
Right-hand drive
SIPS bag system
The SIPS bag system consists of a gas
generator, side airbag and sensors. A sufficiently violent collision trips the sensors and
ignites the gas generator, inflating the side
airbag. The airbag inflates between the
occupant and the door panel and thereby
cushions the initial impact while deflating.
The side airbag is only normally deployed on
the side of the collision.
OP
Safety
Inflatable Curtain (IC)
Properties
The inflatable curtain is a supplement to the
SIPS system. It is concealed in the headlining
along both sides of the roof and protects
both front and rear seat passengers. The
inflatable curtain is activated by the SIPS
collision sensors if the car is hit from the side.
When deployed, the inflatable curtain
inflates. The inflatable curtain helps to
prevent the driver and passengers from
striking their heads on the inside of the car
during a collision.
OQ
WARNING!
The inflatable curtain is a supplement to
the seatbelts.
Always use a seatbelt.
WARNING!
Never hang or fasten anything on the roof
handles. The hook is only intended for
light outer garments (not for hard objects
such as umbrellas).
Do not screw or fit anything to the
headlining, door pillars or side panels.
This could compromise the intended
protection. Only use Volvo genuine parts
that are approved for placement in these
areas.
Safety
WHIPS
Protection against whiplash
injury — WHIPS
The whiplash protection system (WHIPS)
consists of energy absorbing backrests and
specially designed head restraints for the
front seats. The system is actuated by a rearend collision, where the angle and speed of
the collision, and the nature of the colliding
vehicle all have an influence.
WARNING!
The WHIPS system is a supplement to the
seatbelts. Always wear your seatbelt.
Properties of the seat
When the WHIPS system is deployed, the
front seat backrests fall backward to alter the
position of the driver and front seat
passenger. This diminishes the risk of
whiplash injury.
WHIPS system and child seats/
booster cushions
The WHIPS system does not diminish the
protection provided by the car to children
seated in a child seat or on a booster
cushion.
WARNING!
Never modify or repair the seat or WHIPS
system yourself. Contact an authorised
Volvo workshop.
Correct seating position
For the best possible protection, the driver
and front seat passenger should sit in the
OR
Safety
WHIPS
centre of the seat with as little space as
possible between the head and the head
restraint.
You may place:
• a child seat or booster cushion on the
front passenger seat, provided the
passenger airbag is not activated1.
• a rear-facing child seat in the rear seat
that uses the back of the front seat as
support.
WARNING!
If a seat has been subjected to extreme
forces, such as due to a rear collision, the
WHIPS system must be checked by an
authorised Volvo workshop.
Part of the WHIPS system’s
protective capacity may have been lost
even if the seats appear to be
undamaged. Contact an authorised Volvo
workshop to have the system checked
even after a minor rear-end collision.
1.
OS
For information on activated/deactivated airbag (SRS), see page 20.
Do not obstruct the WHIPS
system
WARNING!
Do not squeeze rigid objects between the
rear seat cushion and the front seat
backrest. Make sure you do not to
obstruct the function of the WHIPS
system.
WARNING!
If a rear seat backrest is folded down, the
corresponding front seat must be moved
forward so that it does not touch the
folded backrest.
Safety
When are the safety systems activated?
System
Triggered
Seatbelt tensioner
Airbags (SRS)
In a frontal collision.1
Side airbags (SIPS)
In a side-impact accident.1
Inflatable curtains
In a side-impact accident.1
In a rear-end collision.
Whiplash protection WHIPS
In a frontal collision and/or side-impact accident.
1. Airbags do not always deploy during a collision. The particular impact may not require the function, with the car’s other safety systems providing
occupants adequate protection.
If the airbags have been deployed, the
following is recommended:
• Have the car transported to an authorised
Volvo workshop. Do not drive with
deployed airbags.
• Let an authorised Volvo workshop replace
components in the car’s safety system.
• Always contact a doctor.
NOTE! The SRS, SIPS, IC and belt tensioner
systems are deployed only once during a
collision.
WARNING!
The AIRBAG control unit is located in the
centre console. If the centre console is
drenched with water or other liquid,
disconnect the battery cables. Do not
attempt to start the car since the airbags
may deploy. Have the car transported to
an authorised Volvo workshop.
WARNING!
Never drive with deployed airbags. They
can make steering difficult. Other safety
systems may also be damaged. The
smoke and dust created when the airbags
are deployed can cause skin and eye
irritation after intensive exposure. In case
of irritation, wash with cold water. The
rapid deployment sequence and airbag
fabric may cause friction and skin burns.
OT
Safety
Crash mode
WARNING!
Never attempt to repair your car or reset
the electronics yourself if the car has been
in CRASH MODE. This could result in
personal injury or the car not functioning
as normal. Always allow an authorised
Volvo workshop to check and restore the
car to normal status after CRASH MODE
has been displayed.
Attempting to start the car
First, check that no fuel is leaking from the
car. There should be no smell of fuel.
Driving after a collision
If the car is involved in a collision, the text
CRASH MODE – SEE MANUAL may
appear on the information display. This
means that the car has reduced functionality.
CRASH MODE is a protective state that is
enforced when the collision may have
damaged the car’s vital functions, such as the
fuel lines, sensors for one of the safety
systems, or the brake system.
WARNING!
Never, under any circumstances, attempt
to restart the car if it smells of fuel when
the CRASH MODE message is indicated.
Leave the car at once.
If everything seems normal and you have
checked for indications of fuel leakage, you
may attempt to start the car.
• Firstly, remove the ignition key and then
reinsert it. The car’s electronics will now
try to reset themselves to normal mode.
Then try to start the car. If CRASH MODE
OU
is still shown in the display then the car
must not be driven or towed. Even if the
car appears to be driveable, hidden
damage may make the car impossible to
control once moving.
WARNING!
If the car is in CRASH MODE it must not
be towed. It must be transported to an
authorised Volvo workshop.
Moving the car
If NORMAL MODE is shown after CRASH
MODE has been reset, the car can be moved
carefully out of a dangerous position. Do not
move the car further than necessary.
Safety
Inspecting the airbags and inflatable curtains
Inspection intervals
The decal on the door pillar(s) shows the
dates (year, month) when you should contact
an authorised Volvo workshop to inspect and,
if necessary, replace the airbags, belt
tensioners and inflatable curtains. If you have
questions concerning the systems, contact
an authorised Volvo workshop.
1.
2.
3.
4.
5.
6.
Driver airbag
Front passenger airbag
Side airbag on the driver’s side
Side airbag on the passenger side
Inflatable curtain on the driver’s side
Inflatable curtain on the passenger side
This decal is located in the rear left door
opening.
OV
Safety
Child safety
NOTE! Regulations regarding the placement
of children in cars vary from country to
country. Check what laws apply.
You may place:
• a child seat or booster cushion on the
front passenger seat, provided the
passenger airbag is not activated1.
• a rear-facing child seat in the rear seat
that uses the back of the front seat as
support.
Child seats and airbags are not compatible
Child seats and airbags
Children should sit comfortably
and safely
Always place a child in the rear seat if the
passenger airbag is activated2. A child in a
child seat on the front passenger seat may
suffer serious injury if the airbag deploys.
The position of a child in the car and the
choice of equipment is dictated by the child’s
height and weight, for more information, see
page 32.
WARNING!
Children of all ages and sizes must always sit
correctly secured in the car. Never allow a
child to sit on the knee of a passenger.
Volvo’s own child safety equipment is
designed for your car. Use Volvo genuine
equipment to best ensure that the mounting
points and attachments are correctly
positioned and are sufficiently strong.
PM
Persons shorter than 140 cm (4 ft 7) may
only sit in the front passenger seat if the
passenger airbag is deactivated.
1.
For information on activated/deactivated airbag (SRS), see page 20.
2.
For information on activated/deactivated airbag (SRS), see page 20.
Safety
Decals on the end of the dashboard
Decal located on the car’s sun visor
WARNING!
Never place a child in a child seat or on a
booster cushion in the front seat if the
airbag (SRS) is activated1. Failure to
follow this advice can endanger the life of
the child.
1.
For information on activated/deactivated airbag (SRS), see page 20.
PN
Safety
Child safety
Placement of children in the car
Weight/age
<10 kg
(0–9 months)
9–18 kg
(9–36 months)
15–36 kg
(3–12 years)
Front seat1
Outer rear seat
Centre rear seat
Rear-facing child seat, secured with
seatbelt and straps. Use a
protective cushion between the
child seat and the dashboard.
Rear-facing child seat, secured with
seatbelt, support legs and straps.
Rear-facing child seat, secured with
seatbelt, support legs and straps.
L2: Type approval no. E5 03135
L2: Type approval no. E5 03135
Rear-facing child seat, secured with
seatbelt, support legs and straps.
Rear-facing child seat, secured with
seatbelt, support legs and straps.
L2: Type approval no. E5 03135
L2: Type approval no. E5 03135
Alternatives:
Booster cushion with or without
backrest.
Booster cushion with or without
backrest.
L2: Type approval no. E5 03135
Rear-facing child seat, secured with
seatbelt and straps. Use a
protective cushion between the
child seat and the dashboard.
L2: Type approval no. E5 03135
Booster cushion with or without
backrest.
L2: Type approval no. E5 03139
L2:
L2: Type approval no. E5 03139
Type approval no. E5 03139
Integrated booster cushion.
L2: Type approval no. E5 03168
1. For information on activating/deactivating the airbag (SRS), see page 20.
2. L: Suitable for certain child seats as listed in the specified type approval. Child seats can be vehicle-specific, limited, semi-universal or universal.
PO
Safety
WARNING!
Never place a child in a child seat or on a
booster cushion in the front seat if the
airbag (SRS) is activated.
No one shorter than 140 cm (4 ft 7)
should sit in the front passenger seat if the
airbag (SRS) is activated.1
Failure to follow the advice given above
can endanger the life of the child.
1. For information on activating/deactivating
the airbag (SRS), see page 20.
ISOFIX fixture system for child
seats (option)
Integrated booster cushion
(option)
The outer rear seats have ISOFIX attachment
points. Contact a Volvo dealer for further
information on child safety equipment.
Volvo’s integrated booster cushion for the
outer rear seats is specially designed to
provide optimum safety for children.
Combined with the regular seatbelts, the
booster cushion is approved for children
weighing between 15 and 36 kg.
PP
Safety
Child safety
Check that:
• the seatbelt is in contact with the child’s
body and is not slack or twisted, and that
the belt is positioned correctly across the
shoulder.
• the hip strap is low across the hips for
optimum protection.
• the belt does not touch the child’s throat
or lie below the shoulder.
Carefully adjust the position of the head
restraint to suit the child.
WARNING!
Raising the booster cushion
– Pull that handle to raise the booster
cushion (1).
– Grasp the cushion with both hands and
push it backwards (2).
– Push until it locks in place (3).
WARNING!
The booster cushion must be in the locked
position before the child is placed there.
PQ
If an integrated booster cushion has been
subjected to a major load, such as in
conjunction with a collision, the entire
booster cushion must be replaced. This
includes the seatbelt, complete with bolts.
Even if the booster cushion appears to be
undamaged, it may not afford the same
level of protection. The booster cushion
must also be replaced if it is heavily worn.
Lowering
– Pull the handle (1).
– Lower the seat and press until it locks (2).
NOTE! Remember to stow away the booster
cushion before lowering the rear seat
backrest.
Safety
Replacing the booster cushion
It is important that the integrated booster
cushion is properly secured. Therefore, leave
replacement and any repair of the cushion to
an authorised Volvo workshop. Do not modify
or adapt the booster cushion in any way.
Fitting a child seat
Volvo has child safety products that are
designed for and tested by Volvo.
When using other products that are available
on the market, it is important to read the fitting
instructions included with the product.
• Do not attach the straps for the child seat
to the horizontal adjustment bar, springs,
rails or beams under the seat. Sharp
edges can damage the straps.
• Allow the back of the child seat to rest
against the dashboard. This applies to
cars without a passenger airbag, or
where the airbag is deactivated.
• Never place the child seat in the front
seat if the car is equipped with an
activated1 front passenger airbag. If
problems arise when fitting child safety
products, contact the manufacturer for
clearer instructions.
1.
For information on activated/deactivated airbag (SRS), see page 20.
PR
Safety
PS
Instruments and controls
Combined instrument panel
Indicator and warning symbols
Information display
Electrical socket and switches on centre console
Lighting panel
Left-hand stalk switch
Right-hand stalk switch
Cruise control (option)
Steering wheel keypad (option)
Steering wheel adjustment, hazard warning flashers
Parking brake, electrical socket
Power windows
Rearview and door mirrors
Power sunroof (option)
Personal preferences
38
39
43
44
45
47
49
51
52
53
54
55
58
61
63
PT
Instruments and controls
Combined instrument panel
1.
2.
3.
4.
5.
6.
PU
Speedometer
Direction indicators, left
Warning symbol
Information display — The display
presents information and warning
messages, outside temperature and the
time. When the ambient temperature is
between +2 °C and –5 °C, a snowflake
symbol appears on the display. This
warns of icy roads. The outside temperature gauge may show a slightly high
reading after the car has been stationary
Information symbol
Direction indicator, right
7.
Tachometer — Indicates engine speed
in thousands of revolutions per minute
(rpm)
8. Indicator and warning symbols
9. Fuel gauge
10. Button for trip meter — Used to measure
short distances. Press the button to
switch between trip meters T1 and T2.
Press and hold (more than 2 seconds)
to zero the active trip meter
11. Display — Display for automatic gear
position, rain sensor, odometer, trip
meter and cruise control
12. Main beam indicator
13. Knob for clock — Turn the knob to adjust
the time
14. Temperature gauge — Displays the
temperature of the engine cooling
system. A message will appear on the
display if the temperature becomes too
high and the gauge goes into the red
zone. Bear in mind that extra lights
placed in front of the air intake, for
example, reduce the cooling capacity at
high outside temperatures and high
engine loads
15. Indicator and warning symbols
Instruments and controls
Indicator and warning symbols
Indicator and warning symbols
– Read the information on the information
display.
– Rectify the fault as instructed or contact
an authorised Volvo workshop.
When one of the car’s systems
does not behave as intended,
the yellow information symbol
lights up and a text appears on
the display. The message text is
cleared using the READ button, see page 43,
or disappears automatically after 2 minutes.
All indicator and warning symbols light up
when the ignition key is turned to position II
before starting. This is to check that the
symbols/lights are working. When the engine
starts, all the symbols should go out except
the handbrake symbol, which extinguishes
when the handbrake is released.
If the engine does not start
within five seconds, all
symbols extinguish except the
symbols for a fault in the car’s
emissions system and for low
oil pressure. Certain symbols
may have no function, depending on the car’s
specifications.
The yellow information symbol can also
come on in conjunction with other symbols.
Symbols in the centre of the
instrument panel
The red warning symbol lights
up when a fault has been
indicated which could affect the
safety and/or driveability of the
car. At the same time an explanatory text is
shown in the information display. Symbol and
message text are visible until the fault has
been rectified.
NOTE! When the message text "TIME
FOR REGULAR SERVICE" is shown, the
symbol lamp and message text are cleared
using the READ button, or disappear
automatically after 2 minutes.
The warning symbol can also light up in
conjunction with other symbols.
– Stop in a safe place. Do not drive the car
further.
PV
Instruments and controls
Indicator and warning symbols
– Drive to an authorised Volvo workshop to
have the ABS checked if the symbol
remains lit.
Rear fog lamp
This symbol is lit when the rear
fog lamp is on.
STC or DSTC stability system
A flashing symbol indicates that
the stability system is operating.
Indicator symbols — left-hand
side
Fault in car’s emissions system
Drive to an authorised Volvo
workshop to have the system
checked.
ABS fault
If this symbol lights, the system is
not working. The car’s regular
brake system continues to work,
but without the ABS function.
– Stop the car in a safe place and turn off
the engine.
– Restart the engine.
QM
Engine preheater (diesel)
This symbol is lit during engine
preheating. Preheating occurs
when the temperature is below
-2 °C. The car can be started
once the symbol extinguishes.
Low level in fuel tank
This symbol lights when there are
approximately 8 litres of usable
fuel left in a petrol-engined car, or
7 litres in a diesel-engined car.
Indicator symbols — right-hand
side
Indicator symbol for trailer
This symbol flashes when the
direction indicators are used and
a trailer is coupled. If the symbol
does not flash, one of the lamps
on the trailer or the car is defective.
Parking brake applied
This symbol is lit even if the
parking brake is only applied one
notch. Check that the lever is
properly applied.
Instruments and controls
Airbags – SRS
If this symbol remains on or
comes on while driving, it means
a fault has been detected in the
seatbelt buckle, SRS, SIPS, or IC
system. Drive directly to an authorised Volvo
workshop to have the system checked.
Low oil pressure
If this symbol lights up while
driving, the engine oil pressure is
too low. Stop the engine immediately and check the engine oil
level, top up if necessary. If the symbol lights
up and the oil level is normal, contact an
authorised Volvo workshop.
Seatbelt reminder
This symbol lights if someone in a
front seat has not put on their
seatbelt or if someone in a rear
seat has taken off their seatbelt.
Alternator not charging
If this symbol lights while driving,
a fault has occurred in the
electrical system. Contact an
authorised Volvo workshop.
Fault in brake system
If this symbol lights, the brake
fluid level may be too low.
– Stop the car in a safe place and check the
level in the brake fluid reservoir, see
page 162. If the level in the reservoir is
below MIN, the car should not be driven
any further. Transport the car to an
authorised Volvo workshop to have the
brake system checked.
If the BRAKE and ABS symbols
come on at the same time, there
may be a fault in the brake force
distribution system.
–
•
•
•
•
WARNING!
If the BRAKE and ABS symbols are lit at
the same time, there is a risk that the rear
end will skid during heavy braking.
–Stop the car in a safe place
and turn off the engine.
Restart the engine.
If both symbols extinguish, continue
driving.
If the symbols remain on, check the level
in the brake fluid reservoir. See page 162.
If the brake fluid level is normal but the
symbols are still lit, the car can be driven,
with great care, to an authorised Volvo
workshop to have the brake system
checked.
If the level in the reservoir is below MIN,
the car should not be driven any further.
Have the car transported to an authorised
Volvo workshop to have the brake system
checked.
QN
Instruments and controls
Indicator and warning symbols
Reminder — doors not closed
If one of the doors, the bonnet1 or the boot lid
is not properly closed, the driver will be
reminded of this.
Low speed
If the car is travelling at more
than 7 km/h, the information
symbol will light and one of the
following texts will be shown on
the display: DRIVER
DOOR OPEN, PASSENGER DOOR OPEN,
LEFT REAR DOOR OPEN,
BONNET OPEN, or RIGHT REAR
DOOR OPEN. Stop the car as soon as it is
safe to do so and close the door that is open.
High speed
If the car is travelling at more
than 7 km/h, the warning
symbol will light and one of the
texts from the previous
paragraph will appear on the display.
Boot lid reminder
If the boot lid is open, this information symbol will come on and
TAILGATE OPEN will appear
on the display.
1.
QO
Only cars with alarms.
Instruments and controls
Information display
Messages
When a warning or indicator symbol come, a
message appears on the information display.
– Press the READ button (A).
Switch between messages with the READ
button. Fault messages are stored in the
memory until the fault is rectified.
NOTE! If a warning message appears while
you are using the trip computer, the message
must be read (press READ) before the
previous activity can be resumed.
Message
STOP SAFELY
STOP ENGINE
SERVICE URGENT
SEE MANUAL
SERVICE REQUIRED
TIME FOR REGULAR SERVICE
Specification
Stop and switch off the engine. Serious risk of damage.
Stop and switch off the engine. Serious risk of damage.
Leave the car for servicing immediately.
Read the owner’s manual.
Have your car serviced as soon as possible.
Time for service. The interval depends on distance, number of months since last service and
engine running time.
QP
Instruments and controls
Electrical socket and switches on centre console
Pull out the lighter and light a cigarette on the
heated coils.
Stability system, STC or DSTC1
The stability control system comes on
automatically when the car is started.
To suppress the stability control system:
– Press and hold the button for at least half
a second.
For further information, see page 113.
WARNING!
Electrical socket, DSTC system, extra
equipment
Suppressing the stability control system
alters the driving characteristics of the car.
12 V electrical socket
The electrical socket can be used for 12 V
accessories, such as mobile phone chargers
and coolers. The maximum current is 10 A.
For the socket to supply current, the ignition
key must be in at least position I.
Extra equipment
Space for an extra switch for retrofitted
equipment.
WARNING!
Always leave the plug in the socket when
the socket is not in use.
Cigarette lighter (option)
Activate the lighter by pushing in the button.
The button pops out when the lighter is hot.
QQ
1.
Option on certain markets
Instruments and controls
Lighting panel
Cars with daytime running lights
(certain countries)
Dipped beam comes on automatically when
the ignition key is switched to the driving
position (II) and cannot be switched off.
Before trips to countries where automatic dip
beam is unsuitable, the daytime running lights
can be deactivated. Contact an authorised
Volvo workshop. Front and rear position/
parking lamps, number plate lighting and
instrument lighting are lit at the same time as
dipped beam.
1. Headlamp levelling
This control adjusts the height of the
headlamp beam. This is used when the car is
so heavily laden that it affects the height of
the beams.
• Normal bean height - move the control
upward (0).
• Lowered beam height - move the control
downward.
Cars with Bi-Xenon headlamps (option) have
automatic headlamp levelling.
2. Headlamps and position/
parking lamps
All lighting off.
Position/parking lamps
Front and rear position/parking
lamps, number plate lighting and
instrument lighting. See also
page 47.
Main and dipped beam
Ignition key in position II:
Headlamps (plus front and rear
position/parking lamps, number
plate lighting and instrument
lighting) are lit.
NOTE! The light switch must be turned to this
position to switch on the main beam.
However, it is possible to flash the main beam
in all positions, even when the ignition key is
removed. See also page 47.
3. Instrument lighting
Manual adjustment:
• Brighter illumination - move the control
upwards.
• Dimmer illumination - move the control
downwards.
Automatic control:
To improve readability and save electricity, a
twilight sensor automatically adjusts the
brightness of the instrument lighting.
To improve the clarity of the centre console
display, the background colour switches
between dark and light to suit lighting conditions.
4. Front fog lamps (option)
Ignition key in position II:
Press the button. The front fog lamps light
along with the position/parking lamps and
main/dipped beam. The LED in the button is
lit while the front fog lamps are on.
NOTE! In some countries, it is prohibited to
use dipped beam or main beam at the same
time as front fog lamps.
5. Fuel filler flap
Press the button to open the fuel filler flap.
QR
Instruments and controls
Lighting panel
6. Rear fog lamp
Ignition key in position II:
Press the button to switch on the rear fog
lamp. The rear fog lamp lights along with the
front fog lamps or main/dipped beam. The
LED in the button and the symbol in the
combined instrument panel light. If the front
fog lamps and the main or dipped beam are
switched off and on again, the rear fog lamp
goes out. Press the button to switch it on
again.
Dazzling
Remember to switch off the rear fog lamp
when you see a car in the rearview mirror.
Only the last car in a queue should have the
rear fog lamp switched on.
NOTE! Regulations for the use of front and
rear fog lamps vary from country to country.
QS
Instruments and controls
Left-hand stalk switch
Main beam flash (3)
Pull the lever towards you (until you feel a
slight resistance). The main beam remains lit
until you release the lever.
Switching between main and dipped
beam (3)
Pull the lever towards you past the "flash
position" and release it to change between
main and dipped beam.
Home safe lighting (3)
When leaving the car in the dark or in a dimly
lit area:
Direction indicators, light switch
and main beam flash
Resistance point position (1)
When changing lanes or overtaking, move
the lever until you feel a distinct resistance.
The lever returns when released. This action
results in three flashes.
Normal turns (2)
The direction indicators light when you move
the lever in the direction the steering wheel
moves during a turn. When the steering
wheel returns to centre after a turn, the
direction indicators switch off automatically.
– Remove the key from the ignition switch.
– Pull the stalk switch towards you.
– Exit the car.
– Lock the doors.
The dipped-beam lighting, position/parking
lights, number plate lighting and door mirror
lamps (option) will come on. These lamps will
remain lit for 30, 60 or 90 seconds. You can
adjust the delay from the car settings menu
on the centre console display. See page 64.
Trip computer
Controls
To scroll through trip computer information,
turn the thumbwheel (B) in steps, either
upward or downward. Continue turning to
return to the starting point.
NOTE! If a warning message interrupts while
you are using the trip computer, this message
must be acknowledged. Acknowledge by
pressing the READ button (A) and revert to
the trip computer function.
Functions
The trip computer displays the following
information:
• AVERAGE SPEED
QT
Instruments and controls
Left-hand stalk switch
• SPEED IN MILES PER HOUR1
• CURRENT FUEL CONSUMPTION
• AVERAGE FUEL CONSUMPTION
• RANGE TO EMPTY FUEL TANK
Average speed
When the ignition is switched off, the
average speed is stored and used as the
basis of the new value when you continue
driving. Reset using the RESET button (C).
Speed in miles per hour1
Current speed is displayed in mph.
Current fuel consumption
Present fuel consumption is calculated every
second. The information on the display is
updated every couple of seconds. When the
car is stationary, " ---- " appears on the
display.
Average fuel consumption
The average fuel consumption since the last
reset (RESET). The average fuel
consumption is stored when the ignition is
switched off and remains until the function is
reset. Reset using the RESET button (C).
NOTE! There may be a slight error in the
reading if a fuel-driven heater is used.
1.
QU
Certain countries
Range to empty fuel tank
This calculation is based on the average fuel
consumption over the last 30 km (19 miles)
and the remaining fuel volume. It displays the
approximate distance that can be driven with
the fuel remaining in the tank. When the
range to empty is less than 20 km (12 miles)
"----" appears on the display.
NOTE! There may be a slight error in the
reading if a fuel-driven heater is used.
Resetting
– Select average speed or average fuel
consumption.
– Press and hold the RESET button (C) for
at least five seconds to reset the average
speed and average fuel consumption at
the same time.
Instruments and controls
Right-hand stalk switch
Single sweep
Raise the stalk switch to make a
single sweep.
Intermittent wiping
The delay between sweeps can
be adjusted. Turn the
thumbwheel (C) upward for a
shorter interval between sweeps. Turn it
downward to increase the delay.
Continuous wiping
The wipers sweep at normal
speed.
Windscreen wipers
A. Windscreen and headlamp washers
B. Rain sensor - On/Off
C. Thumbwheel
D. Rear window wiper and washer
Windscreen wipers off
The windscreen wipers are off
when the stalk switch is in
position 0.
The wipers sweep at high
speed.
Windscreen/headlamp washer
Pull the stalk switch towards the steering
wheel to start the windscreen and headlamp
washers. The wipers will make three more
sweeps once the stalk is released.
The headlamps are washed the first time the
windscreen is washed. Within the next ten
minutes, they are washed every fifth wash of
the windscreen. If more than ten minutes
passes between washes, the headlamps are
washed every time.
Parking/position lamps selected with the
switch on the lighting panel:
• Bi-Xenon headlamps are only washed
every fifth wash cycle irrespective of the
time that elapses.
• Halogen headlamps are not washed.
The switch on the lighting panel is in
position 0:
• Bi-Xenon headlamps are only washed
every fifth wash cycle irrespective of the
time that elapses.
• Halogen headlamps are not washed.
High-pressure headlamp washing
(option on certain markets)
High-pressure headlamp washing consumes
a large quantity of washer fluid. To save fluid,
the headlamps are washed as follows.
Dipped beam selected with the switch on
lighting panel:
QV
Instruments and controls
Right-hand stalk switch
To activate the rain sensor:
– press button (B). The rain sensor symbol
is shown on the lower display.
To turn the rain sensor off, either:
Rain sensor (option)
The rain sensor detects the amount of water
on the windscreen so that the windscreen
wipers automatically increase or decrease
speed. The sensitivity of the rain sensor is
adjusted with the thumbwheel (C).
Turn the thumbwheel upward for higher
sensitivity and downward for lower sensitivity.
(An extra sweep is made when the
thumbwheel is turned upward.)
On/Off
When activating the rain sensor, the ignition
key must be in at least position I and the
windscreen wiper stalk must be in position 0.
RM
– press button (B).
– press the stalk switch downward to
another wiper program. If the stalk switch
is raised, the rain sensor will remain
active; the wipers make an extra sweep
and then return to rain sensor mode when
the stalk is released to position 0.
The rain sensor is automatically deactivated
when the key is removed from the ignition
switch or five minutes after the ignition is
switched off.
Important!
In an automatic car wash:
Turn off the rain sensor by pressing button
(B) while the ignition key is in at least
position I. Otherwise, the windscreen
wipers may start and be damaged.
Thumbwheel
Use the thumbwheel to adjust the frequency
of sweeps when intermittent wiping is
selected, or the sensitivity to rain when the
rain sensor is selected.
Instruments and controls
Cruise control (option)
Temporary disengagement
– Press 0 to disengage the cruise control
temporarily. CRUISE will be shown on the
combined instrument panel. The speed
set earlier is stored in the memory.
The cruise control is also temporarily disengaged when:
Activating
Increasing or decreasing speed
The controls for cruise control are to the left
of the steering wheel.
– Increase or decrease the speed by
pressing and holding + or —. The speed
of the car when the button is released is
set as the new speed.
Pressing (less than half a second) + or —
changes the speed 1 km/h (0.6 mph) or
1.6 km/h (1 mph)1.
Setting the desired speed:
– Press the CRUISE button. CRUISE is
shown on the combined instrument panel.
– Touch + or — to lock the vehicle speed.
CRUISE ON appears on the combined
instrument panel.
Cruise control cannot be engaged at speeds
below 30 km/h (20 mph) or above 200 km/h
(125 mph).
NOTE! A temporary increase in speed (less
than one minute) using the accelerator, such
as while overtaking, does not affect the cruise
control setting. When you release the accelerator, the car will return to the programmed
speed.
1.
• the brake pedal or clutch pedal is
depressed.
• speed falls below 25-30 km/h when
travelling uphill1.
• the gear selector is moved to position N.
• wheel spin or wheel lock-up occurs.
• a temporary increase in speed lasts
longer than one minute.
Return to the set speed
Press this button to resume the
previously set speed.
CRUISE ON appears on the
combined instrument panel.
Disengaging
Press CRUISE to disengage the cruise
control. CRUISE ON goes out on the
combined instrument panel.
Depending on engine type
RN
Instruments and controls
Steering wheel keypad (option)
The four buttons at the bottom of the steering
wheel keypad control the radio and the
telephone. The function of a button depends
on which system is active. The steering wheel
keypad can be used to scroll between preset
stations, change CD/MD tracks and adjust
the volume.
Press and hold one of the arrow keys to fast
forward/reverse or search for the next station.
The telephone must be in standby mode to
adjust audio system settings.
The telephone must be activated to control
the telephone functions using the arrow keys.
RO
Instruments and controls
Steering wheel adjustment, hazard warning flashers
Steering wheel adjustment
Hazard warning flashers
The steering wheel can be adjusted for both
height and reach.
– Pull the lever towards you to release the
steering wheel.
– Adjust the steering wheel to the position
that suits you best.
– Push back the lever to fix the steering
wheel in place. If the lever is stiff, press
the steering wheel lightly at the same time
as you push the lever back.
Use the hazard warning flashers (all direction
indicators flash) when the car is stopped
where it could be a traffic hazard or
obstruction. Press the button to activate the
function.
NOTE! Regulations regarding the use of
hazard warning flashers vary from country to
country.
WARNING!
Adjust the steering wheel before driving
off, never while driving. Before driving,
check that the steering wheel is fixed in
position.
RP
Instruments and controls
Parking brake, electrical socket
Parking brake (handbrake)
The lever is located between the front seats.
The parking brake acts on the rear wheels. A
warning symbol on the combined instrument
panel lights when the brake is applied.
The warning symbol lights even if the parking
brake is only applied one notch. Check that
the lever is properly applied.
To release the parking brake:
– Pull the lever up slightly and press in the
button. Lower the lever and release the
button.
Electrical socket in the rear seat
The electrical socket can be used for 12 V
accessories, such as mobile phone chargers
RQ
and coolers. The maximum current is 10 A.
For the socket to supply current, the ignition
key must be in at least position I.
WARNING!
Always leave the plug in the socket when
the socket is not in use.
Cigarette lighter (option)
Activate the lighter by pushing in the button.
The button pops out when the lighter is hot.
Pull out the lighter and light a cigarette on the
heated coils.
Instruments and controls
Power windows
Operation
Automatic operation
– Fully depress one of the controls (A) or
(B) or raise it fully, then release. The side
window will then open or close automatically. If the window is obstructed by an
object, the movement will stop.
The power windows are operated using the
controls in the door armrests. The ignition key
must be in position I or II for the power
windows to operate. The windows continue
to work when the car is stopped and ignition
key removed, provided neither of the front
doors is opened.
WARNING!
To open a window:
– Depress the front of the control.
To close a window:
– Raise the front of the control.
Remote control and central locking
buttons
All side windows can be opened/closed
automatically with the remote control or the
central locking buttons:
– Press and hold the lock button for two
seconds - the windows will open or close.
To interrupt opening/closing:
– Press the lock button again.
WARNING!
A. Front door window B. Rear door window
Driver’s door
The driver can operate all of the power
windows from the driver’s seat.
The windows in the front doors can be
opened and closed in two ways:
Manual operation
– Depress one of the controls (A) or (B)
gently or raise it gently. The power
window opens or closes as long as the
switch is actuated.
If there are children in the car:
Remember to switch off the supply to the
power windows by removing the ignition
key if the driver leaves the car.
Make sure that children’s and other
passengers’ hands are clear when closing
the windows.
WARNING!
If the rear door windows are operated
from the driver’s door:
Check that none of the rear seat
passengers are in danger of getting their
hands caught when closing the windows.
Make sure that children’s or other
passengers’ hands are clear when closing
the windows by remote control.
RR
Instruments and controls
Power windows
The switch LED is unlit
The rear door windows can be operated both
with the control on each rear door and with
the controls on the driver’s door.
Blocking rear power windows and electric
child safety locks1
Front passenger seat
Blocking power windows in the rear
doors
The switch LED is lit.
The control in the front passenger door
operates that window only.
The rear door windows can only be operated
from the driver’s door.
NOTE! If the car has electric child safety
locks1 on the rear doors, the LED indicates
that these are activated. The doors cannot
then be opened from the inside. When the
electric child safety locks are activated, a text
message is shown on the display.
1.
RS
Option
Front passenger seat
Instruments and controls
Rear power windows
The rear door windows can be operated with
the control on each door or with the switch on
the driver’s door. If the LED in the switch for
blocking the rear power windows (located in
the control panel in the driver’s door) is lit, the
rear door windows can only be operated from
the driver’s door. The windows in the rear
doors are operated in the same way as the
windows in the front doors.
RT
Instruments and controls
Rearview and door mirrors
Interior rearview mirror
Dipping
1. Dip the mirror with the lever
2. Normal position
3. Dipped position. Use this to reduce
annoying dazzle from the headlights of
following vehicles.
Autodimming (option)
A sensor (4) on the bottom edge of the mirror
detects light coming from behind and dims
the mirror if the light is strong. An authorised
Volvo workshop can adjust the sensitivity.
NOTE! The illustration is a montage. The
mirror has either manual dipping or automatic
dimming, never both at the same time.
RU
Rearview mirror with compass
(option on certain markets)
The upper right-hand corner of the rearview
mirror has an integrated display that shows
the compass direction in which the front of
the car is pointing. Eight different directions
are shown with English abbreviations:
N (north), NE (north east), E (east),
SE (south east), S (south), SW (south west),
W (west) and NW (north west).
Calibrating the compass
The compass may need calibrating in special
cases (setting points of the compass). The
letter C is shown in the mirror’s display if the
compass needs calibrating.
– Stop the car in a large open area.
– Start the car.
– Press and hold button (1) (use the point
of a pen or similar) for at least six
seconds. The character C will reappear.
– Drive slowly in a circle at a speed of no
more than 10 km/h until a compass
direction appears on the display.
– Calibration is complete.
Instruments and controls
– The display will revert to showing the
compass direction a few seconds after
you stop scrolling.
Magnetic zones
Adjusting the zone
The earth is divided into 15 magnetic zones.
The compass is set for the geographical area
to which the car was delivered.
Door mirrors
Select a different compass area as follows:
– Press the L button for the left-hand door
mirror or R for the right-hand door mirror.
The LED in the button lights.
– Adjust the position with the joystick in the
centre.
– Press the L or R button again. The LED
should no longer be lit.
Retractable power door mirrors
(option)
The mirrors can be retracted for parking and
driving in narrow spaces.
– Turn on the ignition.
– Press and hold button (1) for at least
three seconds (use the point of a pen or
similar). The number for the current area
is displayed.
– Press the button repeatedly until the
number for the required geographic
area (1-15) is shown.
The controls for adjusting the two door
mirrors are at the front of the driver’s door
armrest.
RV
Instruments and controls
Rearview and door mirrors
Important!
Do not use a scraper to remove ice from
the mirrors as this can scratch the glass.
Use the defroster function instead, see
page 69.
WARNING!
The driver-side door mirror is wide angled
to provide optimal vision. Objects may
appear further away than they actually are.
– Press the L and R button at the same
time.
– Release them after approximately
one second. The mirrors automatically
stop in the fully retracted position.
SM
Folding out the mirrors
– Press the L and R button at the same
time. The mirrors automatically stop in the
fully extended position.
Resetting to neutral
Mirrors that have been moved out of position
by an external force must be reset to the
neutral position for electric retracting and
extending to work.
Proceed as follows:
– Press the L and R button to retract the
mirrors.
– Extend the mirrors again with the L and R
button. The mirrors are now reset to the
neutral.
Home safe and approach lighting
The lamps on the door mirrors light when the
home safe lighting or approach lighting is
activated.
Instruments and controls
Power sunroof (option)
– Pull the control rearward to the end
position (1) and release.
Sliding position
Automatic operation
Pull the control past the point of
resistance (2) to the rear end position (1) or
past the point of resistance (3) to the forward
end position (4) and release. The sunroof
opens/closes completely.
Manual operation
Open:
Open positions
The sunroof controls are located in the roof
panel. The sunroof can be opened to two
positions:
Ventilation position, raised at the rear
edge (A).
Sliding position, backwards/forwards (B).
The ignition key must be in position I or II.
WARNING!
If there are children in the car:
Switch off the supply to the power sunroof
by removing the ignition key if the driver
leaves the car.
1. Opening, automatic
2. Opening, manual
3. Closing, manual
4. Closing, automatic
5. Opening, ventilation position
6. Closing, ventilation position
Ventilation position
Open:
– Press the rear edge of the control (5)
upward.
Close:
– Pull the rear edge of the control (6)
downward.
From ventilation position to fully open
sunroof:
– Pull the control rearward to the point of
resistance (2). The sunroof moves toward
the fully open position as long as the
button is held in this position.
Close:
– Press the control forward to the point of
resistance (3). The sunroof moves toward
the closed position as long as the button
is held in this position.
WARNING!
The sunroof’s pinch-protection function
only operates during automatic closing,
not manual closing.
SN
Instruments and controls
Power sunroof (option)
WARNING!
Make sure that the hands of children and
passengers are clear when closing the
sunroof by remote control.
Sunscreen
The sunroof features a manual, sliding interior
sunscreen. The sunscreen slides back
automatically when the sunroof is opened.
Grip the handle and slide the screen
forwards to close the screen.
Pinch protection
Closing using the remote
control or central locking button
Closing using the remote control or central
locking button:
– Press and hold the lock button for two
seconds. The sunroof and windows close
and the doors lock.
If you need to interrupt closing:
– Press the lock button again.
SO
The sunroof’s pinch protection function is
activated if the hatch is blocked by an object.
If blocked, the sunroof will stop and automatically open to the previous position.
WARNING!
The sunroof’s pinch protection function
only operates during automatic closing,
not during manual closing.
Make sure children’s hands are clear
when closing the sunroof.
Instruments and controls
Personal preferences
and audio functions. For audio functions, see
page 183.
Control panel
A. Display
B. MENU
C. EXIT
D. ENTER
E. Navigation
Use
The settings are shown on the display (A).
Open the menu to enter settings:
– Press MENU (B).
– Scroll, for example, to "Car Settings" with
the navigation button (E).
– Press ENTER (D).
– Select an alternative with the navigation
button (E).
– Activate your selection with ENTER.
Close the menu:
– Press EXIT (C) for approximately one
second.
Climate control
Control panel
Possible settings
Personal preferences can be set for some of
the car’s functions: the locks, climate control
Recirculation timer
When the timer is active, the air recirculates
for 3-12 minutes, depending on the outside
air temperature.
– Select On/Off depending on whether you
wish the recirculation timer to be active.
Reset all
Resets the climate function options to the
factory settings.
Car settings
Unlock feedback light
The hazard warning flashers can provide
feedback when the car is unlocked with the
remote control. This function can be turned
On or Off.
Lock feedback light
The hazard warning flashers can provide
feedback when the car is locked with the
remote control. This function can be turned
On or Off.
Autolock
The doors and boot lid can be locked
automatically when the car starts to move.
The setting options are On or Off.
Automatic fan adjustment
The fan speed can be set to AUTO mode in
cars equipped with ECC:
Unlock doors
There are two alternatives for unlocking:
– Select between Low, Normal and High.
• All doors — one press of the remote
control unlocks all doors.
SP
Instruments and controls
Personal preferences
• Drivers door first, then all others — one
press of the remote control unlocks the
driver’s door. A second press then
unlocks all the other doors.
Keyless door opening
• All doors - all doors are locked or
unlocked at the same time.
• Doors on the same side - front and rear
doors on the same side are unlocked
together.
• Both front doors - both front doors are
unlocked together.
• One front door - one of the front doors
(either) can be unlocked separately.
Approach lighting
Select the time the car’s lights should remain
on when the approach lighting button is
pressed. The following alternatives are
available: 30/60/90 seconds.
Home safe lighting
Select the time the car’s lights should remain
on when the left-hand stalk switch is pulled
back after the ignition key has been removed.
The following alternatives are available:
30/60/90 seconds.
Information
• VIN (Vehicle Identification Number). The
car’s unique identity number.
SQ
• Number of keys. The number of keys
registered for the car is shown.
Climate control
General information on climate control
Manual climate control, A/C
Electronic climate control, ECC (option)
Air distribution
Fuel-driven parking heater (option)
66
68
70
73
74
SR
Climate control
General information on climate control
Air conditioning
The climate control system cools or heats,
and dehumidifies the air entering the
passenger compartment. The car is equipped
with either manual (A/C) or electronic climate
control (ECC).
NOTE! The air conditioning can be switched
off, but for optimum air quality in the
passenger compartment and to prevent the
windows from misting up, it should always be
on (even at temperatures of 0-15 °C).
Misting windows
Reduce the problem of windows misting up
on the inside by cleaning the windows. Use a
regular window cleaner.
Ice and snow
Remove ice and snow from the climate
control air intake (the grille between the
bonnet and the windscreen).
Fault tracing
An authorised Volvo workshop has the instruments and tools required for any fault tracing
or repair of your climate control system.
Entrust checks and repairs only to trained
personnel.
Refrigerant
The air conditioning system contains R134a
refrigerant. This refrigerant contains no
SS
chlorine, which means that it is harmless to
the ozone layer. The system must only be
charged with R134a refrigerant. Have an
authorised Volvo workshop carry out this
work.
Passenger compartment filter
All air which enters the passenger
compartment is first cleaned by a filter. This
filter must be replaced regularly. Follow the
Volvo Service Programme for the recommended replacement intervals. If the car is
used in a severely contaminated environment,
it may be necessary to replace the filter more
often.
NOTE! There are several different types of
passenger compartment filter. Ensure that
the correct filter is installed.
Display
There is a display above the climate control
panel that displays climate control settings.
Personal preferences
You can set preferences for two climate
control functions:
• Fan speed in AUTO mode (applies only
to cars with ECC).
• Recirculation timer for passenger
compartment air.
For information about these settings, see
page 63.
Air vents in the dashboard
A. Open
B. Closed
C. Lateral airflow
D. Vertical airflow
Aim the outer vents towards the side
windows to remove misting.
Cold weather: Close the centre vents for
optimum comfort and best demisting.
Climate control
ECC (option)
Actual temperature
The temperature you select corresponds to
the physical experience with reference to
factors such as air speed, humidity and solar
radiation in and around the car.
Condensation
In warm weather, condensation from the air
conditioning system may drip under the car.
This is normal.
Sensor location:
• The sun sensor is on the top side of the
dashboard.
• The temperature sensor for the
passenger compartment is behind the
climate control panel.
NOTE! Do not cover or block the sensors
with clothing or other objects.
Side windows and sunroof
To ensure that the air conditioning works
satisfactorily, close all side windows and the
sunroof (if fitted).
Acceleration
The air conditioning system switches off
temporarily at full throttle. You may feel a
temporary rise in temperature.
Ventilation slots in the parcel shelf
Do not obstruct the ventilation slots for the
cargo compartment in the parcel shelf with
clothing or other objects.
ST
Climate control
Manual climate control, A/C
Control panel
1.
2.
3.
4.
5.
6.
7.
8.
9.
SU
Fan
Recirculation
Defroster
Air distribution
AC - ON/OFF
Heated front left seat
Heated front right seat
Rear window and door mirror defrosters
Temperature
Functions
1. Fan
Increase or decrease the fan
speed by turning the knob.
If the knob is turned
anticlockwise and the fan
indicator in the display goes
out, the fan and the air conditioning are switched off. The display shows
the fan symbol and OFF.
2. Recirculation
Recirculation can be used to
shut out bad air, exhaust
fumes, etc. from the
passenger compartment.
The air in the passenger
compartment is recirculated.
No outside air is taken into the car when this
function is activated. Recirculation (together
with the air conditioning system ) cools the
passenger compartment more quickly in hot
weather. If the air in the car recirculates for
too long, there is a risk of the windows
misting.
Climate control
Timer
The timer function minimises the risk of icing,
misting and bad air if recirculation is selected.
See the Personal Preferences section,
page 63, for how to activate and deactivate
the function. Recirculation is always disengaged when you select Defroster (3).
3. Defroster
Defroster quickly removes
misting and ice from the
windscreen and side
windows.
• Air is directed to the windows at high fan
speed.
• The LED in the defroster button lights
when the function is active. The air conditioning system gives maximum dehumidification.
• The air does not recirculate.
4. Air distribution
The airflow can be
distributed to the windows,
dashboard vents or floor by
pressing the air distribution
buttons.
A symbol on the display
above the climate control panel and a lit LED
in the button indicate which function has
been selected.
See the table on page 73.
5. AC - ON/OFF
ON: Air conditioning is
engaged.
OFF: Air conditioning is
disengaged. If Defroster (3)
is activated the air conditioning is always engaged.
function is active if one LED is lit in the switch.
The door mirror heating is deactivated
automatically after approximately 6 minutes.
The rear window heating is deactivated after
approximately 12 minutes.
9. Temperature
Select cooling or heating for
both driver and passenger
side.
6 and 7. Heated front seats
(option on certain markets)
–Higher heat level
Press the button once both LEDs light.
–Lower heat level
Press the button twice - one LED lights.
– Heat off
Press the button three times - LEDs not
lit.
8. Rear window and door mirror
defrosters
Heating is used to quickly
remove misting and ice from
the rear window and door
mirrors.
The rear window and door
mirrors are defrosted simultaneously if the switch is pressed once. The
SV
Climate control
Electronic climate control, ECC (option)
Control panel
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
TM
AUTO
Fan
Recirculation/Air quality system
Defroster
Air distribution
AC - ON/OFF
Heated front left seat
Heated front right seat
Rear window and door mirror defrosters
Temperature
Functions
1. AUTO
The AUTO function
automatically regulates
climate control and
maintains the desired
temperature. The AUTO
function controls heating, air
conditioning, fan speed, recirculation, and air
distribution. If you select one or more manual
functions, the other functions continue to be
controlled automatically. All manual settings
are switched off when AUTO is switched on.
The display shows AUTO CLIMATE.
2. Fan
Increase or decrease fan
speed by turning the knob.
The fan speed is regulated
automatically if AUTO is
selected and the previously
set fan speed is disengaged.
NOTE! If the knob is turned anticlockwise and
the fan indication on the display goes out, the
fan and the air conditioning are switched off.
The display shows the fan symbol and OFF.
Climate control
3. Recirculation
Recirculation can be used to
shut out bad air, exhaust
fumes, etc. from the
passenger compartment.
The air in the passenger
compartment is recirculated.
No outside air is taken into the car when this
function is activated. If the air in the car recirculates for too long, there is a risk of misting
on the insides of the windows.
Timer
The timer function minimises the risk of icing,
misting and bad air if recirculation is selected.
See Personal Preferences, page 63, for how
to activate and deactivate the function.
NOTE! When Defroster (4) is selected, recirculation is always deactivated.
3. Air quality system (option)
(same button as recirculation)
The air quality system
consists of a multi-filter and
a sensor. The filter
separates gases and
particles to reduce the levels of odours and
pollution in the passenger compartment.
When the sensor detects polluted outside
air, the air intakes are closed and the air in the
passenger compartment is recirculated.
A green LED (A) lights in the button when the
air quality sensor is active.
Activating the air quality sensor:
• Press the AUTO button (1) to activate the
air quality sensor (normal setting).
Or:
Switch between three functions by pressing
repeatedly the recirculation button.
• Air quality sensor engaged - LED (A)
lights.
• No recirculation engaged, provided it is
not required for cooling in hot weather LED not lit.
• Recirculation engaged - LED (M) lights.
Keep in mind the following:
• As a rule, the air quality sensor should
always be engaged.
• Recirculation is limited in cold weather to
avoid misting.
• If the insides of the windows start misting
up, disengage the air quality sensor.
• The defroster function for the front, side
and rear windows can also be used to
demist the windows.
4. Defroster
Defroster quickly removes
misting and ice from the
windscreen and side
windows. Air flows to the
windows at high fan speed.
The LED in the defroster
button lights when the function is active. The
air conditioning system gives maximum
dehumidification. The air is not recirculated.
5. Air distribution
The airflow can be
distributed to the windows,
dashboard vents or floor by
pressing the air distribution
buttons.
A symbol on the display
above the climate control panel and a lit LED
in the button indicate which function has
been selected.
See the table on page 73.
6. AC— ON/OFF
The air conditioning system
is controlled automatically
by the system when the ON
LED is lit. This way,
incoming air is sufficiently
cooled and dehumidified.
When the OFF LED lights, the air conditioning system is always disengaged. Other
TN
Climate control
Electronic climate control, ECC (option)
functions are still controlled automa tically.
When Defroster (4) is selected, the air conditioning system is set for maximum dehumidification.
10. Temperature selector
The temperatures on the
driver and passenger sides
can be set independently.
7 and 8. Heated front seats
(option on certain markets)
Press the button once to
activate one side. Press
again to activate the other
side. Press the button a third time to activate
both sides.
To activate front seat
heating:
– Higher heat level:
Press the button once - both LEDs light.
– Lower heat level:
Press the button twice - one LED lights.
– Heat off:
Press the button three times - LEDs not lit.
9. Heated rear window and door mirrors
Heating is used to quickly
remove misting and ice from
the rear window and door
mirrors.
The rear window and door
mirrors are defrosted simultaneously if the switch is pressed once. The
function is active if one LED is lit in the switch.
The door mirror heating is deactivated
automatically after approximately 6 minutes.
The rear window heating is deactivated after
approximately 12 minutes.
TO
The active side is indicated by an LED in the
button and on the display above the climate
control panel.
When the car is started, the previous settings
are resumed.
NOTE! Heating or cooling cannot be
hastened by selecting a higher or lower
temperature than the actual desired
temperature.
Climate control
Air distribution
Air distribution
Air distribution
Air to windows. Some
air flows to the
dashboard air vents.
The air is not recirculated. Air conditioning is
always engaged.
Air to windscreen and
side windows. Some air
flows to the dashboard
air vents.
Use:
To remove ice and
misting quickly.
Air distribution
Air to the floor and
windows. Some air
flows to the dashboard
air vents.
Use:
To ensure
comfortable conditions and good
demisting in cold or
humid weather.
To prevent misting
and icing in a cold
and humid climate.
(Not for low fan
speed.)
Air to floor and from
dashboard air vents.
In sunny weather
with cool outside
temperatures.
Airflow to windows and
from dashboard air
vents.
To ensure good
comfort in warm, dry
weather.
Air to the floor. Some
air flows to the
dashboard air vents
and windows.
To warm the feet.
Airflow to the head and
chest from the
dashboard air vents.
To ensure efficient
cooling in warm
weather.
Airflow to windows,
from dashboard air
vents and to the floor.
To provide cooler air
for the feet or
warmer air to the
upper body in cold
weather or hot, dry
weather.
TP
Climate control
Fuel-driven parking heater (option)
maximum running time of the parking heater
is 60 minutes.
WARNING!
The car must be outdoors when the petrol
or diesel heater is used.
WARNING!
General information about
heaters
The parking heater can be started immediately or set with two different start times
using TIMER 1 and TIMER 2. Here, start time
refers to the time the car is heated and ready.
The car’s electronic system calculates when
heating should be started based on the
outside temperature. The heater is not run if
the outdoor temperature exceeds 25 °C. At
temperatures of T10 °C and below, the
TQ
Switch off the fuel-driven heater before
refuelling. Spilled fuel could be ignited by
the exhaust gases.
Check on the information display that the
heater is off. (When the additional heater
is running, PARK HEAT ON is shown on
the information display.)
Warning decal on fuel filler flap
WARNING!
The car must be outdoors when the petrol
or diesel heater is used.
Climate control
Activating the heater
Battery and fuel
– Enter the time when the car is to be used.
Press RESET (C) to enter the hours and
minutes.
– Press and hold the RESET button until
the timer is activated.
If the battery has insufficient charge or the
fuel level is too low, the parking heater will be
switched off automatically. A message
appears on the information display.
Acknowledge the message by pressing the
READ button (A).
Parking on a hill
If the car is parked on a steep hill, the front of
the car should point downhill to ensure that
there is a supply of fuel to the parking heater.
Direct start
– Use the thumbwheel (B) to scroll to
DIRECT START.
– Press RESET (C) to access the options
ON and OFF.
– Select ON. The heater will now run for
60 minutes. Heating of the passenger
compartment will begin as soon as the
engine coolant has reached a temperature of 30 ºC.
Immediate stop of heater
– Use the thumbwheel (B) to scroll to
DIRECT START.
– Press RESET (C) to access the options
ON and OFF.
– Select OFF.
NOTE! The car can be started and driven
while the parking heater is still running.
Important!
– Scroll with the thumbwheel to the desired
minute.
– Touch RESET to confirm the setting.
– Press RESET to activate the timer. After
setting TIMER 1, a second start time can
be programmed with TIMER 2 . Access
this with the thumbwheel. Set the alternative start time in the same way as
TIMER 1.
Repeated use of the parking heater
combined with short journeys may
discharge the battery and impair starting.
If the heater is used regularly, the car
must be driven for the same as the heater
is run to ensure that the alternator has
time to charge the battery.
Setting TIMER 1 and 2
For safety reasons, you can only programme
times for the following 24 hours, not several
days in advance.
– Scroll with the thumbwheel to TIMER.
– Touch RESET to move to the flashing
hours setting.
– Scroll with the thumbwheel to the desired
hour.
– Touch RESET to move to the flashing
minutes setting.
TR
Climate control
Fuel-driven heater (option)
Messages on the display
When TIMER 1, TIMER 2 and DIRECT
START are activated, the information symbol
on the combined instrument panel lights and
an explanatory text appears on the information display. The display also indicates
which timer is active when the driver removes
the key from the ignition to leave the car.
Clock/timer
If the car clock is reset after the heater timers
are programmed, the selected times will be
cancelled.
Additional heater (diesel)
(certain countries)
Extra heat from the additional heater may be
required in cold weather to reach the correct
temperature in the passenger compartment.
The additional heater starts automatically
when extra heat is required if the engine is
running. It is switched off automatically when
the correct temperature is reached or when
the engine is switched off.
TS
Interior
Front seats
Interior lighting
Storage spaces in the passenger compartment
Rear seat
Cargo area
78
80
82
84
86
TT
Interior
Front seats
5. Backrest rake: turn the wheel.
6. Control panel for power seat (option).
Controls (2) and (3) are not present on all
seat models.
WARNING!
Adjust the position of the driver’s seat
before setting off, never while driving.
Check that the seat is locked in position.
Seating position
The driver’s and passenger seats can be
adjusted to the optimum sitting and driving
positions.
1.
2.
3.
4.
TU
Forward/backward: lift the handle to
adjust the distance to the steering
wheel and pedals. Check that the seat is
locked after changing position.
Raise/lower the front of the seat
cushion: pump up/down (option on
passenger side).
Raise/lower the seat: pump up/down
(option on passenger side).
Lumbar support (option, passenger
side), turn the wheel.
Lowering the front seat
backrest
The passenger seat backrest can be folded
forward to make room for long loads.
– Move the seat as far back as possible.
– Adjust the backrest to an upright position
90 degrees.
– Lift the catches on the rear of the
backrest while folding it forwards.
Interior
the door is opened within two minutes, the
driver’s seat returns to the stored position.
about 20 seconds before adjusting the seat
again.
Seat with memory function (option)
1. Seat adjustment, memory 1
2. Seat adjustment, memory 2
3. Seat adjustment, memory 3
4. Storing preset positions
Three positions can be stored. After
adjusting the seat, press and hold
button M (4) and then press button (1).
Further seat settings can be stored in the
memory using memory buttons (2) and (3).
Emergency stop
If the seat accidentally begins to move, press
one of the buttons to stop the seat.
Setting preset positions
Power seat (option)
Preparations
The seat is normally adjusted with the ignition
key is in position I or II. It can also be adjusted
within 10 minutes of the door being unlocked
with the key or remote control. If the door is
closed and the ignition key is not yet in the
ignition, or is in the 0 position, adjustments
can be made within 40 seconds of the door
being closed.
Memory function in remote control
The remote control used to unlock the car
stores information about the changes made
to the seat settings. When the car is next
unlocked with the same remote control and
Press and hold one of the memory
buttons (1), (2) or (3) until the seat stops. If
you release the button, the seat stops
immediately for safety reasons.
WARNING!
Ensure that there is nothing in front of,
behind, or under the seat during
adjustment.
Ensure that none of the backseat
passengers will be trapped.
To avoid injury, ensure that children do not
play with the switches.
Seat adjustment
The following can be set with switches (5),
(6) and (7):
5. Backrest rake
6. Seat forward/backward and up/down
7. Front edge of seat cushion up/down
Only one of the electric motors can be
operated at a time. The power front seats
have overload protection which is tripped if a
seat is blocked by an object. If this happens,
turn off the ignition (position 0) and wait
TV
Interior
Interior lighting
• On - left side depressed, passenger
compartment lighting is on.
Automatic lighting
The interior lighting switches on and off
automatically when switch (2) is in the neutral
position. See illustration.
The lighting comes on and remains on for
30 seconds if:
Front seat lighting
1. Lighting for left-hand side
2. Switch
3. Lighting for right-hand side
The lighting in the front part of the passenger
compartment is controlled with the buttons in
the roof console.
Switch (2) has three positions for all
passenger compartment lighting:
• Off - right side depressed, passenger
compartment lighting is switched off.
• Neutral position - passenger
compartment lighting comes on when a
door is opened and goes out when the
door is closed. The dimmer function is
active.
UM
• the car is unlocked from outside with the
key or remote control.
• the engine is stopped and the ignition key
is turned to position 0.
The compartment lighting comes on and
remains on for five minutes if:
• one of the doors is open.
• the lighting is not switched off.
The interior lighting is switched off when:
• the engine is started.
• the car is locked from outside with the key
or remote control.
The interior lighting is automatically switched
off five minutes after the engine is switched
off. The interior lighting can be switched on or
off within 30 minutes of the key being turned
to position 0 by briefly pressing button 2. The
programmed times can be changed in
accordance with the instructions in the
Personal Preferences section, see page 59.
Rear seat lighting
Turn the lights on or off by pressing the
appropriate button. The lighting is turned off
automatically ten minutes after the engine is
switched off.
Interior
Vanity mirror1
The light comes on automatically when the
cover is lifted.
1.
Option on certain markets.
UN
Interior
Storage spaces in the passenger compartment
UO
Interior
Storage spaces
1.
2.
3.
4.
5.
6.
7.
Storage pocket (also on the front edge
of the front seat cushions).
Compartment in door panel.
Ticket clip.
Glovebox.
Waste bin (accessory).
Storage compartment and cup holder.
Storage compartment and cup holder.
Important!
The waste bin (5) must not be mounted if
a phone handset is mounted on the righthand side of the centre console.
WARNING!
Ensure that no hard, sharp or heavy
objects lie or protrude in such a way that
they could cause injury during heavy
braking.
Always secure large and heavy objects
with a seatbelt or cargo retaining straps.
Glovebox
The owner’s manual and maps can be kept
here. There are also holders for coins, pens
and fuel cards. The glovebox can be locked
with the removable key blade in the remote
control. For further information about the key,
see page 88.
Floor mats (option)
Volvo supplies floor mats specially manufactured for your car. These should be properly
anchored with the clips on the floor so they
do not slide and get jammed beside or under
the driver’s pedals.
UP
Interior
Rear seat
Important!
The head restraints can be damaged if
they are not removed for loading. The
centre head restraint must also be
removed for heavy loads.
Centre rear head restraint
All head restraints can be adjusted vertically
to suit the height of the passenger. The upper
edge of the head restraint should be aligned
with the middle of the back of the head. Raise
the head restraint if necessary. To lower the
head restraint, press the button by the righthand pillar at the same time as pushing down
the head restraint.
To remove the head restraint, press the
button by the right-hand pillar while lifting the
head restraint.
UQ
Tipping the rear seat backrest
The rear seat backrests can be tipped
forwards together, or individually, to make it
easier to transport long objects. To avoid
damaging the seatbelts when folding the
backrests up or down, these should be
hooked onto the grab handles.
– Hang the seatbelts on the hooks before
lowering or raising the backrests.
– Lift the rear edge of the seat cushion (1)
in order to fold the seat cushions forward.
Interior
WARNING!
Remember to take down the seatbelts
once you have raised the backrest.
Lowering the backrest
– Pull the lock (2) catch up and forward to
release the backrest. A red indicator on
the lock catch shows that the backrest is
no longer locked in place.
– Fold the backrest (3) forward halfway and
remove the head restraint. The centre
seat’s head restraint must be lowered
fully or removed.
– Place the head restraints in the plastic
sleeves on the undersides (4) of the
raised seat cushions.
NOTE! When the backrest has been raised,
the red indicator should no longer be
showing. If it is, the backrest is not locked in
place.
UR
Interior
Cargo area
Load retaining eyelets
The load retaining eyelets are used to fasten
straps or nets to anchor items in the cargo
area.
US
Electrical socket in the cargo
area
Fold down the cover to access the electrical
socket. This socket works regardless of
whether the ignition is on. If the ignition is
switched off and an appliance requiring a
current greater than 0.1 A is plugged into the
electrical socket, a warning message
appears on the information display. Avoid
using the electrical socket with the ignition
switched off due to the risk of running the
battery flat.
Bag holder (option)
The bag holder holds shopping bags in place
and prevents them tipping over and spilling
their contents.
– Open the hatch in the cargo area.
– Secure the shopping bags with the strap.
Locks and alarm
Remote control with key blade
Keyless drive (option)
Locking and unlocking
Child safety locks
Alarm (option)
88
91
93
95
96
UT
Locks and alarm
Remote control with key blade
Remote control
4.
The car is supplied with two remote controls.
These also work as ignition keys. The remote
controls contain a removable metal key blade
for the manual locking and unlocking of the
driver’s door and the glovebox. A separate
label with the code for key blade is included.
Keep this label in a safe place. Take it to an
authorised Volvo workshop when ordering
new keys. A maximum of six remote controls/
key blades can be programmed and used for
one car.
5.
Loss of a remote control
If you lose a remote control, take the car and
the other remote control to an authorised
Volvo workshop. The code of the missing
remote control must be erased as a theft
prevention measure.
Immobiliser
The remote controls are fitted with coded
chips. The code must be accepted by the
reader (receiver) in the ignition switch. The
car can only be started if the correct remote
control with the correct code is used.
UU
Boot lid - Press the button once to
unlock the boot lid only.
Panic function - Used to attract attention
in an emergency. Press and hold the red
button for at least three seconds or
press it twice within three seconds to
activate the direction indicators and the
horn. The function can be turned off with
the same button once it has been active
for at least five seconds. The function
switches off automatically after
30 seconds.
Important!
Remote control functions
1.
2.
3.
Locking - Locks the doors and the boot
lid. Press and hold to close the windows
and sunroof.
Unlocking - Unlocks the doors and boot
lid. Press and hold to open the
windows.
Approach lighting - When you approach
the car:
Press the yellow button on the remote
control to switch on the interior lighting,
position/parking lights, number plate
lighting and door mirror lamps (option).
The lighting is switched off automatically
after 30, 60 or 90 seconds. For how to
set the desired delay time, see page 64.
The narrow section of the remote control
is particularly sensitive - this contains the
chip. The car cannot be started if the chip
is damaged.
Key blade
This feature is intended for when leaving the
car, such as for servicing or valet parking at a
hotel. Hand over the remote control and keep
the removable key blade.
Access to the glovebox and cargo
compartment can be prevented using the
remote control's removable key blade1. This
means that the remote control can only open
the doors and that the car can be driven.
1.
Certain markets only
Locks and alarm
Removing the key blade
To take the key blade out of the remote
control:
– Slide the spring-loaded catch (1) to the
side while pulling the key blade (2) out.
Inserting the key blade
Be careful when inserting the key blade into
the remote control.
– Hold the remote control with the narrow
end pointing down and lower the key
blade into its slot.
– Lightly press the key blade to lock it in
position. You should hear a "click".
1.
2.
Active locks, remote control
Active locks, key blade
symbol and REMOTE BATTERY LOW
VOLTAGE appear on the display.
Service locking1
Locking the glovebox: Turn the key blade
90 degrees clockwise.
Service locking: Turn the key blade
180 degrees clockwise. This also locks the
boot lid which cannot then be opened with
the remote control (a message is shown in the
information display).
Weak remote control battery
When the battery runs down and full functionality cannot be guaranteed, the information
1.
Certain markets only
UV
Locks and alarm
Remote control with key blade
– Prise out (2) and change the battery.
Avoid touching the battery and its
terminals with your fingers.
– Refit the cover and screw it shut.
– Press the key blade back into place.
Dispose of the old battery in an environmentally-friendly way.
Changing the remote control
battery
If the locks repeatedly fail to respond to
signals from the remote control at a normal
distance, the battery should be changed
(type CR 2032, 3 volt).
– Pull out the key blade.
– Place the remote control with the keypad
downward and remove the screw (1)
using a small screwdriver.
– Remove the cover.
– Carefully note the position of the battery’s
+ and – poles on the inside of the cover.
VM
Locks and alarm
Keyless drive (option)
Keyless lock and ignition
system
The keyless drive system allows the car to be
unlocked, driven and locked without the need
for a key. You simply have to have the remote
control with you in a pocket or bag.
The system makes it easier and more
convenient to open the car, for example with
shopping bags in one hand and a child in the
other. It saves you having to take out or look
for the remote control.
The two remote controls incorporate the
keyless drive feature. You can order
additional remote controls. The keyless drive
system can handle up to six remote controls.
Remote control max. 1.5 m from the car
To be able to open a door or the boot lid, the
remote control must be within a maximum of
approximately 1.5 m of the car’s door
handles or boot lid. The grey shaded area in
the image shows the area covered by the
system’s antennae.
If someone leaves the car and takes with
them a keyless drive remote control, a
warning message appears on the information
display while a reminder signal is heard. The
warning message disappears when the
remote control is brought back to the car or
the ignition dial is turned to position I. The
warning is only issued if the key dial is in
position 1 or 2 after someone has opened
and closed a door.
The warning message and reminder signal
disappear when the remote control is
brought back to the car after one of the
following actions:
• a door has been opened and closed
• the ignition dial has been turned to
position I
• the READ button has been pressed.
Do not leave a remote control in the car
If a keyless drive remote control is left in the
car, it becomes passive when you lock the
car. No unauthorised person can open the
door. But if someone breaks into the car and
finds the remote control, it can be activated
and used again.
VN
Locks and alarm
Keyless drive (option)
All doors and the boot lid must be closed
before the lock button is pushed in.
Otherwise they will not lock.
Interference to remote control function
Electromagnetic screening and fields can
interfere with the keyless drive system. To
avoid this:
When the car is locked, the lock buttons on
the inside of the doors retract in the normal
way.
Do not place the remote control near mobile
phones, metallic objects or, for example, in a
metal briefcase.
Personal settings for keyless
drive
If interference is experienced nonetheless,
use the remote control and key blade in the
normal way. See page 88.
The keyless drive system can be tailored to
your personal requirements. Read more
about personal settings on page 64.
Unlocking
Unlock the car by:
– opening one of the doors with the handle
or opening the boot lid by pressing the
button.
Power seat (option) — remote control
with memory function
If several people with keyless drive remote
controls get into the car, the driver’s seat will
be adjusted for the person who opens the
door first.
Locking
Lock the doors and boot lid by:
– pushing in the lock button on one of the
door handles.
VO
Locks and alarm
Locking and unlocking
Locking/unlocking the car from
outside
be locked manually with their respective lock
buttons. Pull the door handle twice to unlock
and open the door from the inside.
You can lock and unlock all the car’s doors
and the boot lid simultaneously using the
remote control. The driver’s door can be
unlocked with the key blade.
WARNING!
Be aware that you can be locked in the car
if it is locked from the outside.
Automatic relocking
If none of the doors or the boot lid are opened
within two minutes of unlocking, all are
locked again automatically. This function
prevents the car from being left unlocked
unintentionally. For cars with alarms, see
page 97.
Unlocking the boot lid
To unlock only the boot lid:
– Press the boot lid button on the remote
control.
If all doors are locked when the boot lid is
closed, then the boot lid remains unlocked
until the car is locked with the remote control
or from inside.
Locking/unlocking the car from
inside
All the doors and the boot lid can be locked
or unlocked simultaneously using the switch
by the door handle.
Unlocking
– Press the upper section of the lock
button. Press and hold to also open the
side windows.
Locking
– Press the lower part of the lock button.
Press and hold to also close the windows
and sunroof.
It is not possible to unlock a door by pulling
up the lock button. All the doors can however
VP
Locks and alarm
Locking and unlocking
Temporary deactivation of the
deadlocks and any detectors
If someone is going to stay in the car but you
still want to lock the doors from the outside,
the deadlocks can be disabled.
– Insert the key into the ignition switch, turn
it to position II and then back to position I
or 0.
– Press button 1.
If the car is equipped with an alarm,
movement and tilt detectors are also deactivated. See page 97.
Locking the glovebox
The glovebox can only be locked and
unlocked with the removable key blade in the
remote control.
– Unlock the glovebox (1) by turning the key
a quarter of a turn (90 degrees)
anticlockwise. The keyhole is vertical in
the unlocked position.
– Lock (2) the glovebox by turning the key a
quarter of a turn (90 degress) clockwise.
The keyhole is horizontal in the locked
position.
VQ
1.
2.
Deactivation of the detectors
No function
Deadlocks
When deadlocked, the doors cannot be
opened from the inside if they are locked. The
deadlocks are activated with the remote
control. The deadlocks are set after a
25 second delay after the doors are locked.
The car can only be unlocked from a
deadlock state with the remote control. The
doors can also be opened from the outside
with the key.
The LED in the button lights up until the car is
locked with the key or the remote control. A
message remains on the display as long as
the key is in the ignition switch. The detectors
are reactivated the next time the ignition is
switched on.
WARNING!
Do not allow anyone to remain in the car
without first deactivating the deadlocks.
Locks and alarm
Child safety locks
Electric child safety locks and
disabling the rear window
buttons (option)
Press the switch on the driver’s door. A
message appears on the information display.
When the electric child safety locks are
activated, the rear window buttons are
disabled.
To activate the child safety locks:
Manual child lock in rear left door.
Manual child locks in the rear
doors
To lock manually: The child safety locks are
found on the trailing edge of the rear doors
and are only accessible when the doors are
open. Use the key blade to turn the lock and
thus activate or deactivate the child safety
lock.
A.
The doors cannot be opened from
inside.
B. The doors can be opened from inside.
Switch for electric child safety locks and
disengaging rear power window buttons.
WARNING!
Always keep the lock buttons pulled up
when driving. In the event of an accident,
this allows the emergency services to get
into the car quickly. Passengers in the rear
seat cannot open the doors from inside if
the child safety locks are activated.
– Turn the ignition key to position I or II.
– Press the switch. When the LED in the
switch is lit, the rear window buttons are
disabled.
A message appears on the information
display when the child safety locks are
activated.
NOTE! Cars with electric child safety locks
do not also have manual child locks.
Child safety locks activated
A lit LED together with a text message on the
display indicates that the locks are activated.
The doors cannot be opened from inside. The
power windows can only be operated with
the controls on the driver’s door.
VR
Locks and alarm
Alarm (option)
The alarm system
When the alarm is armed, it continually
monitors all alarm inputs.
NOTE! Do not attempt to repair or modify
alarm system components. All such attempts
may affect the terms of insurance.
The alarm is triggered if:
Arming the alarm
• a door, the bonnet or the boot lid is
opened.
• a non-approved key is used in the ignition
or if an attempt is made to force the lock.
• a movement is detected in the passenger
compartment (if fitted with a movement
detector).
• the car is raised or towed away (if fitted
with a tilt detector).
• a battery cable is disconnected.
• anyone tries to disconnect the siren.
– Press the LOCK button on the remote
control. A long flash from the car’s
direction indicators confirms that the
alarm is armed and that all the doors are
locked.
Disarming the alarm
Alarm LED on the dashboard
An LED on the dashboard indicates the alarm
system’s status:
• LED not lit - the alarm is not armed.
• The LED flashes once a second - the
alarm is armed.
• The LED flashes rapidly after disarming
the alarm and until the ignition is switched
on - the alarm has been triggered.
If there is a fault in the alarm system, a
message appears on the information display.
Contact an authorised Volvo workshop.
If the alarm system does not work correctly,
let an authorised Volvo workshop examine
the car.
VS
– Press the UNLOCK button on the remote
control. Two short flashes from the car’s
direction indicators confirms that the
alarm is disarmed and all doors are
unlocked.
Locks and alarm
Automatic alarm activation
Alarm signals
This function prevents you accidentally
leaving the car without the alarm on.
When the alarm is triggered, the following
happens:
If none of the side doors or the boot lid are
opened within two minutes of disarming the
alarm (and the car has been unlocked with
the remote control), the alarm is automatically
rearmed. The car is also locked.
• A siren sounds for 30 seconds. The siren
has its own battery which is used if the
car battery has insufficient charge or is
disconnected.
• The direction indicators flash for five
minutes or until the alarm is deactivated.
Switching off a triggered alarm
– Press the UNLOCK button on the remote
control.
Confirmation is given by two short flashes
from the direction indicators.
Remote control not working
If for some reason the remote control is not
working, the alarm can still be switched off
and the car started as follows:
– Open the driver’s door with the key blade.
The alarm is triggered and the siren
sounds.
– Insert the remote control into the ignition
switch. The alarm is deactivated. The
alarm LED flashes rapidly until the ignition
key is turned to position II.
1.
2.
Deactivation of the detectors
No function
Temporary deactivation of the
deadlocks and detectors
To prevent the alarm being tripped erroneously, such as during a ferry journey, the
movement and tilt detectors can be temporarily disengaged.
– Turn the ignition key to position II and
then back to position 0. Remove the key.
– Press button (1). The LED in the button is
lit until the car is locked.
A message remains on the display as long as
the key remains in the ignition switch (and for
1 minute after the key is removed).
VT
Locks and alarm
Alarm (option)
The detectors are reactivated the next time
the ignition is switched on.
If the car has deadlocks, these are also reengaged.
Testing the alarm system
Testing the movement detector in the
passenger compartment
– Open all the windows.
– Arm the alarm. Activation of the alarm is
confirmed by the alarm LED flashing
slowly.
– Wait 30 seconds.
– Test the movement detector in the
passenger compartment, such as by
lifting out a bag from a seat. A siren
should sound and all direction indicators
flash.
– Deactivate the alarm by unlocking the car
with the remote control.
Testing the doors
– Arm the alarm.
– Wait 30 seconds.
– Unlock the driver’s door with the key
blade.
– Open one of the doors. A siren should
sound and all direction indicators flash.
– Deactivate the alarm by unlocking the car
with the remote control.
VU
Testing the bonnet
– Sit in the car and deactivate the
movement detector.
– Arm the alarm. Remain in the car and lock
the doors with the button on the remote
control.
– Wait 30 seconds.
– Open the bonnet with the handle under
the dashboard. A siren should sound and
all direction indicators flash.
– Deactivate the alarm by unlocking the car
with the remote control.
Starting and driving
General
Refuelling
Starting the car
Keyless drive
Manual gearbox
Automatic gearbox
All-wheel drive
Brake system
Stability system
Parking assistance (option)
Towing and recovery
Start assistance
Driving with a trailer
Towing equipment
Detachable towbar
Loading
Adjusting headlamp pattern
100
101
102
104
105
107
110
111
113
115
117
119
120
122
124
129
130
VV
Starting and driving
General
Economical driving
Driving economically means driving smoothly
while thinking ahead and adjusting your
driving style and speed to the prevailing
conditions.
• Get the engine warmed up as soon as
possible.
• Do not let the engine idle, but drive at
light loads as soon as it is possible.
• A cold engine consumes more fuel than a
warm one.
• Avoid sudden unnecessary acceleration
and heavy braking.
• Do not drive with unnecessary loads in
the car.
• Do not use winter tyres when the roads
are dry.
• Remove load carriers when they are not
being used.
• Avoid driving with open windows.
Slippery driving conditions
Practise driving on slippery surfaces under
controlled conditions to learn how the car
reacts.
Engine and cooling system
Under special conditions, for example when
driving in hilly terrain, extreme heat or with
NMM
heavy loads, there is a risk that the engine
and cooling system will overheat.
Avoid overheating the cooling
system
• Maintain a low speed when driving with a
trailer up long, steep ascents.
• Do not turn the engine off immediately
you stop after a hard drive.
• Remove any auxiliary lamps from in front
of the grille if driving in extreme high
temperatures.
Avoid overheating the engine
• Do not drive at more than 4500 rpm
when towing a trailer or caravan in hilly
terrain, as the oil temperature can
become too high.
Open boot lid
Avoid driving with the boot lid open. If it is
necessary to drive with the boot lid open for
a short distance:
– Close all windows.
– Set the air distribution to the windscreen
and floor and run the fan at high speed.
WARNING!
Do not drive with the boot lid open. Toxic
exhaust fumes can be drawn into the car
through the cargo area.
Do not overload the battery
The electrical functions in the car load the
battery to varying degrees. Avoid having the
ignition key in position II when the engine is
turned off. Use position I instead, as less
power is used. The 12 volt outlet in the cargo
area supplies power even when the ignition
key is removed.
Examples of functions that use a lot of power:
• ventilation fan
• windscreen wipers
• audio equipment (high volume)
• parking lights
Also, be aware of different accessories that
load the electrical system. Do not use
functions which use a lot of power when the
engine is switched off.
If the battery voltage is low, a message
appears on the display. The energy-saving
function shuts down certain functions or
reduces the load on the battery by, for
example, slowing the ventilation fan and
switching off the audio equipment. Charge
the battery by starting the engine.
Starting and driving
Refuelling
Filling up with fuel
Fill the tank with fuel until the filler pump cuts
out. Too much fuel can overflow in warm
weather.
Fuel of a lower quality than that specified on
page 216 should not be used as engine
power and fuel consumption can be
negatively affected.
WARNING!
Switch off the fuel-driven heater before
refuelling.
Opening the fuel filler flap
Open the fuel filler flap with the button on the
lighting panel, see page 45. The engine must
be switched off before the flap can be
opened. The fuel flap is located on the rear
right wing.
Fuel which spills on to the ground can be
ignited by the exhaust fumes.
Switch off the fuel-driven heater before
starting to refuel.
Never carry an activated mobile phone
when refuelling the ring signal could
cause spark build-up and ignite petrol
fumes, leading to fire and injury.
Petrol
Important!
Do not add cleaning additives to the
petrol, unless recommended by Volvo.
Diesel
At low temperatures (–5 °C to –40 °C), a
paraffin precipitate may form in the diesel
fuel, which can lead to ignition problems.
Important!
Use special winter grade fuel during cold
months.
Closing
Push in the flap until you hear a click.
Fuel filler flap
Turn the fuel cap until an obvious resistance
is felt. Turn past the resistance until it comes
to a stop. Take out the cap. Hang up the cap
on the inside of the fuel filler flap.
Put the petrol cap back after refuelling. Turn
until one or more clear clicks are heard.
NMN
Starting and driving
Starting the car
Depending on the engine temperature when
the engine is started, the idling speed after a
cold start may be higher than normal for
certain engine types. Volvo strives to
minimise exhaust emissions by having the
engine exhaust system reach the correct
operating temperature as quickly as possible.
NOTE! Never rev the engine hard immediately after a cold start.
WARNING!
Never remove the ignition key from the
steering lock while driving or when the car
is being towed. The ignition key must be in
position (II) when the car is towed. The
steering lock could otherwise be
activated, making it impossible to steer
the car.
Before starting the engine
– Apply the parking brake (handbrake).
Automatic gearbox:
– The ignition key must be in position II,
depress the brake pedal and move the
gear selector to position P or N.
Manual gearbox:
– Put the gear lever in neutral and hold the
clutch pedal fully depressed. This is
NMO
particularly important in very cold conditions.
Starting the engine
Petrol engine:
– Turn the ignition key to position III. If the
engine does not start within
5-10 seconds, release the key and try
again.
Diesel engine:
– Turn the ignition key to position II. A lamp
on the combined instrument panel will
come on indicating that the engine
preheater is activated. Turn the key to
position III when the lamp extinguishes.
Diesel particle filter (certain
models)
Certain diesel cars are equipped with a
particle filter which results in additionally
effective exhaust purification. When the
engine is at its normal operating temperature
(the engine is warm) a "regeneration" of the
filter takes place automatically, which means
that the particles collected in the filter are
burned away and the filter is emptied.
Regeneration takes between five and ten
minutes. During this time fuel consumption
may increase slightly.
Winter driving
If the car is frequently driven short distances
in cold weather then the engine does not
reach normal operating temperature. This
means that regeneration of the diesel particle
filter does not take place and the filter is not
emptied.
When the filter has become approx. 80% full
of particles then the warning text ENGINE
SERVICE REQUIRED is shown in the
dashboard display.
Regeneration should be carried out regularly
if the car is frequently driven short distances
in cold weather in order to avoid impaired
function of the filter.
• Start regeneration of the filter by driving
the car until the engine reaches normal
operating temperature, preferably on a
main road or motorway. The car should
then be driven for approximately
20 minutes more.
• To clear the warning text when regeneration is complete, switch off the ignition,
remove the key, wait for at least three
minutes and switch the ignition on again.
• Use the parking heater (option) in cold
weather so that the engine reaches
normal operating temperature more
quickly.
Important!
If the filter fills up with particles then it can
be difficult to start the engine and the filter
will be incapable of functioning and must
then be replaced.
Starting and driving
Ignition keys and electronic
immobiliser
The ignition key must not hang with other
keys or metal objects on the same key ring.
The electronic immobiliser could be activated
accidentally.
Ignition switch and steering
lock
0 – Locked position
The steering lock is
activated when the key is
removed from the lock.
I – Radio position
Certain electrical components can be switched on.
The engine’s electrical
system is not activated.
II – Driving position
The key position when
driving. The car’s electrical
system is energised.
III – Start position
The starter motor is
engaged. Release the key,
which springs back
automatically to the driving
position, once the engine
has started.
A ticking sound may be heard if the key is
between positions. Turn the key to position II
and back to eliminate the sound.
When the steering lock is
activated
If the front wheels are positioned so that
there is tension in the steering lock, a warning
message may be shown in the information
display and the car prohibited from starting.
– Remove the key and turn the steering
wheel to release the tension.
– Hold the steering wheel in this position.
Reinsert the key and make a new attempt
to start the car.
WARNING!
Never remove the ignition key from the
ignition switch while driving or when the
car is being towed. The steering lock
could otherwise be activated, making it
impossible to steer the car.
WARNING!
Always remove the ignition key from the
ignition when leaving the car, especially if
there are children in the car.
Make sure the steering lock is activated when
the car is left to reduce the risk of theft.
NMP
Starting and driving
Keyless drive
Starting the car
To start the car:
Instead of an ignition key, the car has an
ignition dial. The dial is used in the same way
as the key. The only difference is that to start
the car, either the clutch pedal (manual
gearbox car) or brake pedal (automatic
gearbox car) must be depressed. This is a
safety measure.
• Depress the clutch or brake pedal.
• Press in and turn the dial to position III.
Ignition dial or ignition key
The car can be started with the dial or with
the key.
For the car to start, the car’s passive remote
control/key must be in the passenger or
cargo area.
NMQ
To remove the ignition dial:
Push in the catch and pull out the dial.
Starting and driving
Manual gearbox
Gear positions, five-speed
Depress the clutch pedal fully with each gear
change. Remove your foot from the clutch
pedal between gear changes! Follow the
appropriate shifting pattern.
For the best possible fuel economy, use the
highest gear possible as often as possible.
Reverse gear inhibitor, five-speed
Only engage reverse gear when the car is
stationary. To engage reverse gear, the gear
lever must first be put in position N. Reverse
gear cannot therefore be engaged directly
from fifth gear, because of the reverse gear
inhibitor.
Gear positions, six-speed
(petrol)
Depress the clutch pedal fully with each gear
change. Remove your foot from the clutch
pedal between gear changes! Follow the
appropriate shifting pattern.
For the best possible fuel economy, use the
highest gear possible as often as possible.
It can be difficult to find the positions for fifth
and sixth gear when the car is stationary as
the reverse gear inhibitor (which blocks
sideways movement towards reverse) is then
not activated.
NMR
Starting and driving
Manual gearbox
Reverse gear inhibitor, six-speed
(petrol)
Only engage reverse gear when the car is
stationary.
Gear positions, six-speed
(diesel)
Depress the clutch pedal completely for each
gear change. Remove your foot from the
clutch pedal between gear changes. Follow
the indicated gear pattern. For optimum fuel
economy use the highest possible gear as
often as possible.
Important!
The spring-loaded inhibitor can be forced
when engaging 1st or 2nd gear if you
apply too much pressure to the left when
changing gear. This can lead to reverse
being engaged when driving forwards.
NMS
Reverse gear inhibitor, six-speed
(diesel)
Only engage reverse gear when the car is
stationary. To engage reverse gear, press the
gear lever to the left past the spring-loaded
inhibitor.
Starting and driving
Automatic gearbox
Cold start
Safety systems
When starting in low temperatures, the gear
changes can sometimes feel hard. This is due
to the gearbox oil’s viscosity at low temperatures. To minimise engine emissions, the
gearbox shifts up later than normal when the
engine is started at low temperatures.
Cars with an automatic gearbox have special
safety systems:
NOTE! Depending on the engine temperature when the engine is started, the idle
speed after a cold start may be higher than
normal for certain engine types.
Kick-down
When the accelerator pedal is pressed all the
way to the floor, beyond the position normally
regarded as full acceleration, a lower gear is
immediately engaged. This is known as kickdown.
If the accelerator is released from the kickdown position, the gearbox automatically
changes up.
Kick-down is used when maximum acceleration is needed, such as for overtaking.
To prevent overrevving, the gearbox control
program has a protective downshift inhibitor
which prevents the kick-down function.
The kick-down function cannot be used in
manual gear position (Geartronic).
Keylock
To remove the ignition key, the gear selector
must be in the P position. The key is locked in
all other positions.
Parking position (P)
Stationary car with engine running:
– Hold your foot on the brake pedal when
moving the gear selector to another
position.
Electric gear inhibitor – Shiftlock
Parking position (P position)
To be able to move the gear selector from the
P position to other gear positions, the ignition
key must be in position II and the brake pedal
must be depressed.
Shiftlock - Neutral (N position)
If the gear selector is in the N position and the
car has been stationary for at least three
seconds (irrespective of whether the engine
is running) then the gear selector is locked in
the N position.
NOTE! To be able to move the gear selector
from the N position to another gear position,
the brake pedal must be depressed and the
ignition key must be in position II.
Disengaging shiftlock
In certain cases, it may be necessary to move
the car when it is not driveable, for example if
the battery is flat. Proceed as follows to move
the car:
– There is a small cover behind P-R-N-D on
the gear selector panel. Open the rear
edge.
– Insert the key blade from the remote
control. Press down and hold the key
blade. The gear selector can now be
moved out of the P position.
NMT
Starting and driving
Automatic gearbox
R – Reverse
The car must be stationary when R is
selected.
N – Neutral
N is the neutral position. No gear is engaged
and the engine can be started. Apply the
parking brake when the car is stationary with
the gear selector is in position N.
Mechanical gear selector
inhibitor
The gear selector can be moved freely
between N and D. Other positions are locked
with a latch that is released with the inhibitor
button on the gear selector.
Press the inhibitor button to move the lever
forward or back between R, N and D.
Automatic gear positions
P – Parking position
Select position P when you wish to start the
engine or park the car.
NOTE! The brake pedal must be depressed
to engage the P position.
Important!
The car must be stationary when the P is
selected.
The gearbox is mechanically blocked when P
position is engaged. Always apply the
parking brake when parking the car.
NMU
D – Drive
D is the normal driving position. Shifting up
and down between the different gearbox
ratios takes place automatically based on the
level of acceleration and speed. The car
should be stationary when the gear lever is
moved from position R to position D.
Manual positions
To move from the automatic driving position
D to a manual position, move the gear
selector to position M. To go from position M
to the automatic driving position D, move the
selector to position D.
While driving
The manual gearshift mode can be selected
at any time while driving. The engaged gear is
locked until you choose another gear.
If the gear selector is moved to – (minus) the
car changes down a gear and engine brakes
at the same time as the accelerator pedal is
Starting and driving
released. If the gear selector is moved to
+ (plus) the car changes up a gear.
The selected gear is indicated in the
combined instrument panel (see page 38).
NOTE! Geartronic contains two safety
functions:
• Geartronic does not permit downshifting/
kick-down which would result in an
engine speed high enough to damage the
engine. Nothing happens if the driver tries
to shift down in this way. The original gear
remains engaged.
• Geartronic automatically shifts down if
the driver allows the speed to decrease
lower than a level suitable for the selected
gear, in order to avoid jerking and stalling.
W – Winter
The W button by the gear
selector engages and disengages the winter programme
W. The symbol W is shown
in the combined instrument
panel when the winter
programme is activated.
The winter programme starts the gearbox in a
higher gear to facilitate starting off on
slippery surfaces. The lower gears are only
activated with kick-down when the winter
programme is engaged.
The W programme can only be selected in
position D.
NMV
Starting and driving
All-wheel drive
All-wheel drive – AWD
All-wheel drive is always engaged.
All-wheel drive means that all four road
wheels are driven at the same time. Power is
automatically distributed between front and
rear wheels. An electronically controlled
clutch system distributes the power to the
pair of wheels that grips best. This provides
the best traction and prevents wheel spin.
Under normal driving conditions, the majority
of power is transmitted to the front wheels.
All-wheel drive improves driving safety in rain,
snow and icy conditions.
NNM
Starting and driving
Brake system
Brake servo
If the car is rolling or is being towed with the
engine turned off, the brake pedal must be
pressed about five times harder than when
the engine is running. If the brake pedal is
pressed when the engine is started, you will
feel the pedal drop. This is normal and due to
the brake servo becoming active. This may be
more noticeable if the car has emergency
brake assistance (EBA).
NOTE! If braking with the engine switched
off, press the brake pedal sharply once, not
repeatedly.
WARNING!
The brake servo only works when the
engine is running.
Brake circuits
This symbol lights if a brake circuit is
not working.
If a fault should occur in one of the
circuits, it is still possible to brake the car. The
brake pedal will travel further and may feel
softer than normal. Harder pressure on the
pedal is needed to produce the normal
braking effect.
Dampness can affect braking
characteristics
Brake components become wet when the car
is driven in heavy rain, through pools of water
or when the car is washed. This may alter
brake pad friction characteristics so that
there is a delay before braking effect is
noticed.
using engine braking more efficiently and
requires the foot brake for only brief periods.
Bear in mind that driving with a trailer puts an
additional load on the car’s brakes.
Anti-lock braking system (ABS)
The anti-lock braking system (ABS)
prevents the wheels from locking up
under braking.
This means the ability to steer is
maintained and it is easier to swerve to avoid
a hazard, for example.
Press the brake pedal lightly from time to time
if driving for long stretches in rain or slushy
snow, as well as after setting off in very damp
or cold weather. This warms up the braking
surfaces and dries off any water. It is also
recommended to do this before parking the
car for a long period in such weather conditions.
After the engine has been started, the ABS
will perform a brief self-test at a speed of
about 20 km/h. This can be felt and heard as
pulses in the brake pedal.
If the brakes are used heavily
To get the most out of the ABS:
Because speed is often low, the brakes are
not cooled as effectively as when driving on
flat roads at higher speed.
• Press brake pedal with full force. Pulses
will be felt.
• Steer the car in the direction of travel. Do
not release the pressure on the pedal.
Practice braking with the ABS system in a
traffic-free area and in different weather
conditions.
So as not to overload the brakes, shift down
when driving downhill instead of using the
foot brake. Use the same gear driving
downhill as you would use driving uphill. This
• for about two seconds when the car is
started if the ABS is disengaged due to a
fault.
When driving in the Alps or other roads with
similar characteristics, the car’s brakes are
heavily loaded even if the brake pedal is not
being depressed especially hard.
The ABS symbol lights up:
NNN
Starting and driving
Brake system
Emergency brake assistance – EBA
(Emergency brake assistance) In case of
sudden braking, full-strength braking is
provided instantaneously. The EBA function
senses when heavy braking is underway by
registering how quickly the brake pedal is
depressed. Continue braking without easing
off on the brake pedal. The function is
suspended when the pressure on the brake
pedal eases. This function is always active
and cannot be disengaged.
WARNING!
If the BRAKE and ABS warning symbols
are lit at the same time, a fault may have
occurred in the brake system. If the level in
the brake fluid reservoir is normal, drive
carefully to the nearest authorised Volvo
workshop to have the brake system
checked.
If the brake fluid is under the MIN level in
the brake fluid reservoir, do not drive
further before topping up the brake fluid.
The reason for the loss of brake fluid must
be investigated.
NNO
Starting and driving
Stability system
When the system is in action, it may seem like
the car does not respond normally to acceleration. This is because the system detects the
amount of friction on the road surface and
allows the different stability system functions
to operate.
The car is either equipped with the stability
and traction control system (STC) - or the
dynamic stability and traction control system
(DSTC).
Function/
system
TC
SC
AYC
STC
X
X
DSTC
1
X
X
X
1. Option on certain markets.
Traction Control (TC)
The Traction Control function transfers
power from the spinning drive wheel to the
drive wheel which has grip by braking the
spinning drive wheel. To increase forward
traction in this situation, it may be necessary
to depress the accelerator more than usual. A
pulsing sound is heard when Traction Control
is working. This is completely normal. The TC
function is most active at low speeds. It
cannot be deactivated.
Spin Control (SC)
The Stability Control function prevents the
drive wheels from slipping during acceleration. This improves road safety on slippery
surfaces. Under certain conditions, such as
when driving with snow chains or in deep
snow or sand, it may be beneficial to
deactivate the SC function to increase
traction. This is done with the STC/DSTC
button.
Active Yaw Control (AYC)
The Active Yaw Control function automatically brakes one or more wheels to stabilise
the car in the event of a skid. If the brake
pedal were to be depressed in this situation,
it would feel more rigid than usual and a
pulsing sound would be heard.
The AYC function is always active and cannot
be deactivated.
STC/DSTC button
The STC/DSTC button in the centre console
is used to suppress or reactivate the system.
When the LED in the button is lit, the system
is active. The LED in the button goes out
when the stability system has been
suppressed. Other functions are not
affected.
NOTE! To suppress the STC or DSTC
function, the button must be pressed and
held for at least half a second. The LED in the
button goes out and STC/DSTC SPIN
CONTROL OFF appears on the information
display. The system is automatically activated
every time the engine is started.
NNP
Starting and driving
Stability system
Symbols on the combined
instrument panel
The symbol lights and goes
out again after about
2 seconds
The symbol is lit for a system
check when the car is started.
Flashing warning symbol
The SC function is operating to
prevent the car’s drive wheels from
spinning. The TC function is
operating to improve the car’s
traction. The AYC function is operating to
prevent skidding.
The information symbol
comes on and stays lit
TRACTION CONTROL
TEMPORARILY OFF is shown in
the information display together
with the symbol. The TC function has been
temporarily reduced due to too high brake
temperature.
Automatic reactivation of the function takes
place when the brake temperature has
returned to normal.
NNQ
The information symbol
comes on and stays lit
ANTI-SKID SERVICE REQUIRED
appears on the information display
together with the symbol. The STC
or DSTC system has been switched off
because of a fault.
– Stop the car in a safe place and turn off
the engine.
– Restart the engine.
– If the warning symbol remains lit, drive to a
workshop to have the system checked.
WARNING!
Suppressing the STC or DSTC system
may alter the driving characteristics of the
car. Always take care when cornering and
driving in slippery conditions.
Starting and driving
Parking assistance (option)
If the volume of another sound source from
the audio system is high, this is automatically
lowered.
The system is always active when the car is
started and the text message "Park Assist
active Exit to deactivate" appears on the
audio display.
WARNING!
Parking assistance front and rear.
General
Parking assistance is used as an aid to
parking. A signal indicates the distance to a
detected object.
The frequency of the signal increases as you
come closer to an object1 in front of or
behind the car.
The tone becomes constant at a distance of
about 30 cm. If there are objects within this
distance both behind and in front1 of the car,
the signal alternates between front and rear
speakers.
1.
Provided that the parking assistance
is mounted both front and rear.
Parking assistance does not relinquish the
driver’s own responsibility during parking.
The sensors have blind spots where
objects cannot be detected. Be aware of
children and animals near the car.
Front parking assistance
The distance covered to the front of the car is
about 0.8 m.
Front parking assistance cannot be
combined with extra lights because the
sensors are affected by the extra lights.
Rear parking assistance
The distance covered to the rear of the car is
about 1.5 m.
NOTE! The system must be deactivated
when driving with a trailer, bike carrier on the
towbar or the like as they would trigger the
sensors.
Rear parking assistance is deactivated
automatically when towing a trailer if a Volvo
genuine trailer cable is used.
Deactivating and reactivating
the parking assistance
The parking assistance can be deactivated by
pressing EXIT on the control panel, see page
63. "Park Assist deactivated Enter to
activate" will appear on the audio display. The
parking assistance can be reactivated by
pressing ENTER on the control panel. "Park
Assistance active Exit to deactivate" will then
appear on the audio display.
Front parking assistance
The front parking assistance is active at
speeds of below 15 km/h, even during
reversing.
The signal comes from the front
loudspeakers.
Rear parking assistance
Rear parking assistance is activated when
reverse gear is engaged. If the system is
switched off, the text "Park Assist deactivated
Enter to activate" will appear on the display as
soon as reverse gear is engaged.
The signal comes from the rear loudspeakers.
Fault indicator
The information symbol comes
on and stays lit
PARK ASSIST SERVICE
REQUIRED is shown on the information display in the centre of the combined
instrument panel together with the symbol.
NNR
Starting and driving
Parking assistance (option)
Parking assistance sensors.
Cleaning the sensors
The sensors must be cleaned regularly to
ensure that they work properly. Clean them
with water and car shampoo.
The sensors can react if covered by ice and
snow.
NNS
Starting and driving
Towing and recovery
Never tow the car to bump
start it
Jump start the car with a donor battery if the
battery is flat and the engine does not start.
Do not bump start the car.
Important!
Bump starting the car can damage the
catalytic converter.
Towing
Find out the highest legal speed for towing
before towing the car.
– Turn the ignition switch to position II and
unlock the steering lock so that the car
can be steered, see page 102.
– The ignition key must remain in position II
while the car is being towed.
Automatic gearbox:
– Move the gear selector to position N.
Manual gearbox:
– Move gear lever into neutral.
– Ensure the towrope is always taut to
avoid violent jerks. Keep your foot on the
brake pedal.
Do not tow cars with an automatic gearbox
faster than 80 km/h nor further than 80 km.
WARNING!
The steering lock stays in the position it
was in when the power was cut off. The
steering lock must be unlocked before
towing.
The ignition key must be in position II.
Never remove the ignition key from the
ignition switch while driving or when the
car is being towed.
WARNING!
The brake servo and power steering do
not work when the engine is switched off.
The break pedal must be pressed
about five times harder than normal, and
the steering will be considerable heavier
than normal.
Recovery
Cars with an automatic gearbox should not, if
partly lifted, be towed at more than 80 km/h.
They should not be towed further than 80 km.
NNT
Starting and driving
Towing and recovery
Important!
The towing eye is only designed for
towing on roads, not for pulling the car
unstuck or out of a ditch. Call a recovery
service for assistance.
Towing eye
Use the towing eye if the car needs to be
towed on the road. The towing eye is
attached in the recess on the right-hand side
of the front or rear bumper. To fit the towing
eye:
– Take out the towing eye. This is stored
under the floor hatch in the cargo area.
– Release the bottom edge of the cover on
the bumper with a screwdriver or coin.
– Screw in the towing eye properly, right up
to the flange. Use the wheel wrench to
tighten the towing eye.
– After use, unscrew the towing eye and
return it in the cargo area. Refit the cover
NNU
Starting and driving
Start assistance
Starting with a donor battery
If the battery in the car has become flat, you
can "borrow" electric current from either a
separate battery or the battery in another car.
Always make sure the crocodile clips on the
jump leads are attached securely to eliminate
sparks during the start attempt.
When jump starting the car, the following
steps are recommended to avoid risk of
explosion:
ensure that the cars do not touch one
another.
– Connect the red jump lead between the
positive terminal on the donor battery
(1+) and the one in your car (2+).
– Connect one end of the black jump lead
to the donor battery’s negative
terminal (3–).
– Connect the other end of the black jump
lead to the earthing point (4–) by the lefthand strut tower.
– Start the engine of the "donor car". Let
the engine run a few minutes at a speed
slightly higher than idle 1500 rpm.
– Start the engine of the car with the flat
battery.
– Remove the jump leads, first the black
and then the red. Ensure that neither end
of the black jump lead comes into contact
with the battery’s positive terminal or the
crocodile clip on the red jump lead.
Do not touch the crocodile clips during the
start procedure. This could cause sparking.
WARNING!
The battery can generate oxyhydrogen
gas, which is highly explosive. One spark,
which can be generated if you connect the
jump leads incorrectly, is sufficient to
make the battery explode.
The battery contains sulphuric acid, which
can cause serious burns. If the acid
comes into contact with eyes, skin or
clothing, flush with large quantities of
water. If acid splashes into the eyes, seek
medical attention immediately.
– Turn the ignition key to position 0.
– Ensure that the other battery is 12 volt.
– If the donor battery is in another car,
switch off the engine in the other car and
NNV
Starting and driving
Driving with a trailer
General
The load capacity is affected by extra accessories mounted on the car, such as a towbar,
the load on the towball (75 kg with trailer
hitched), load carriers and roof box, as well as
the passengers’ combined weight. The load
capacity of the car is reduced by the number
of passengers and their weight.
If the towing bracket is mounted at the Volvo
factory, the car is delivered with the
necessary equipment for driving with a trailer.
• The car’s towing bracket must be of an
approved type.
• If the towbar is retrofitted, check with your
Volvo dealer that the car is fully equipped
for driving with a trailer.
• Distribute the load on the trailer so that
the weight on the towing bracket follows
the specified maximum towball load.
• Increase the tyre pressure to the recommended pressure for a full load. See
page 135 for the location of the tyre
pressure label.
• Clean the towbar regularly and grease the
towball1.
1.
NOM
Does not apply to the towball if using
a stabiliser hitch.
• Do not tow a heavy trailer when the car is
brand new. Wait until it has been driven at
least 1000 km.
• The brakes are loaded much more than
usual on long and steep downhill slopes.
Downshift to a lower gear and adjust your
speed.
• The engine is loaded more heavily than
usual when driving with a trailer.
• The engine and gearbox can overheat if
the car is driven with a heavy load in hot
weather. If the temperature gauge for the
engine’s cooling system goes into the red
zone, stop and let the engine idle for a
few minutes. The gearbox responds
through a built-in protection system. See
the message on the information display. If
the car overheats, the air conditioning
may be switched off temporarily.
• In the interests of safety, speed should be
restricted to 80 km/h, even if the laws of
certain countries allow for higher speeds.
• The gear selector should be in the parking
position P when a car with an automatic
gearbox and attached trailer are parked.
Always use the parking brake.
• Place chocks under the wheels to prevent
the car from rolling when parked on a hill
with trailer attached. The gear selector
should be in the parking position P when
a car with an automatic gea rbox and
attached trailer are parked. Always use
the parking brake.
Trailer weights
See page 209 for permitted trailer weights.
NOTE! The stated maximum permitted trailer
weights are those permitted by Volvo.
National vehicle regulations can further limit
trailer weights and speeds. Towbars can be
certified for higher towing weights than the
car can actually tow.
WARNING!
Follow the stated recommendations for
trailer weights. Otherwise, the rig may be
difficult to control during evasive
manoeuvres and braking.
Starting and driving
Automatic gearbox, driving with
a trailer
Parking on a hill:
– Apply the parking brake (handbrake).
– Move gear selector to the parking
position P.
Starting on a hill:
– Move the gear selector to driving
position D.
– Release the parking brake (handbrake).
Steep inclines:
• Select an appropriate manual gear
position when climbing steep inclines or
at low speeds. This prevents the gearbox
from changing up and keeps the gearbox
oil cooler.
• Do not use a higher manual gear than the
engine can "handle". It is not always
economical to drive in high gears.
• Avoid driving with a trailer on inclines of
more than 15 %.
Diesel engine with manual gearbox,
driving with a trailer
If the car is driven with a heavy load in hot
weather then the engine cooling fan should
be replaced with a cooling fan with greater
capacity than the fan fitted as standard. This
is to avoid temporary shut down of the car's
air conditioning and temporary reduction in
engine torque. Consult your Volvo dealer for
information regarding your car's
specifications.
NON
Starting and driving
Towing equipment
Towbars
The towball must be cleaned and greased
regularly. If a towball hitch with vibration
damper is used, it is not necessary to grease
the towball.
If the car is equipped with a detachable
towbar, the towball mounting instructions
must be followed carefully, see page 124.
NOTE! Always take off the towball section
after use. Keep it in the cargo area.
WARNING!
Be sure to attach the trailer’s safety cable
to the correct place.
WARNING!
If the car is fitted with a Volvo detachable
towbar:
Follow the assembly instructions for the
towball section carefully.
The towball section must be locked with
the key before setting off.
Check that the indicator window shows
green.
NOO
Trailer cable
An adapter is required if the car’s towbar has
13 pin electrics and the trailer has 7 pin
electrics. Use an adapter cable approved by
Volvo. Make sure the cable does not drag on
the ground.
Starting and driving
Specifications
Distance A
Fixed towbar: 1055 mm
Distance B
Fixed towbar: 72 mm
Detachable towbar: 72 mm
Detachable towbar: 1055 mm
Maximum ball load: 75 kg
NOP
Starting and driving
Detachable towbar
Fitting the towball
– Remove the guard plug.
NOQ
– Ensure that the mechanism is in the
unlocked position by turning the key
clockwise.
– Check that the indicator window (3)
shows red.
If the window does not show red, press
in (1) and turn the locking wheel
anticlockwise (2) until you hear a click.
Starting and driving
– Insert the towball section until your hear a
click.
– Check that the indicator window shows
green.
– Turn the key anticlockwise to the locked
position. Remove the key from the lock.
NOR
Starting and driving
Detachable towbar
NOTE! Check that the towball section is
secure by pulling it up, down and back. If the
towball section is not fitted correctly then it
must be removed and refitted in accordance
with the previous steps.
NOS
NOTE! The trailer’s safety cable must be
attached to the attachment on the towbar.
Starting and driving
Removing the towball
– Insert the key and turn it clockwise to the
unlocked position.
– Push in the locking wheel and turn it
anticlockwise until you hear a click.
– Turn the locking wheel down fully, until it
comes to a stop. Hold it in this position
while pulling the towball rearward and
upward.
NOT
Starting and driving
Detachable towbar
– Insert the guard plug.
NOU
Starting and driving
Loading
General
The load capacity is affected by extra accessories mounted on the car, such as a towbar,
the load on the towball (75 kg with trailer
hitched), load carriers and roof box, as well as
the passengers’ combined weight. The car’s
load carrying capacity is reduced by the
number of passengers and their weight.
WARNING!
The car’s driving characteristics change
depending on how heavily it is loaded and
how the load is distributed.
Loading the cargo area
Stop the engine and apply the parking brake
when loading or unloading long objects. The
gear lever or gear selector can be knocked
out of position by long loads, which could set
the car in motion. To increase the size of the
cargo area, the head rests can be removed
and the seats folded down, see page 84.
Place the load firmly against the backrest in
front.
• The head rests can be removed so that
they are not damaged.
• Put wide loads in the centre.
• Heavy objects should be placed as low
as possible. Avoid placing heavy loads on
a lowered backrest.
• Cover sharp edges with something soft to
avoid damaging the upholstery.
• Secure all loads to the load retaining
eyelets with straps or web lashings.
WARNING!
A loose object weighing 20 kg can, in a
front-on collision at a speed of
50 km/h, carry the impact of an item
weighing 1000 kg.
WARNING!
Never load cargo above the backrest.
The protection provided by the inflatable
curtain in the headlining may be compromised or eliminated by high loads.
Always secure the load. During heavy
braking the load may otherwise shift,
causing personal injury.
Load carriers
To avoid damaging the car and for maximum
possible safety while driving, it is recommended to use load carriers specially
designed for your car by Volvo.
Carefully follow the mounting instructions
supplied with the carriers.
• Check periodically that the load carriers
and load are properly secured. Lash the
load securely with retaining straps.
• Distribute the load evenly over the load
carriers. Put the heaviest objects at the
bottom.
• The size of the area exposed to the wind,
and therefore fuel consumption, increase
with the load’s size.
• Drive gently. Avoid quick accelerations,
heavy braking and taking curves hard.
WARNING!
Load no more than 75 kg on the roof,
inclusive of the load carriers and any roof
box.
The car’s centre of gravity and driving
characteristics are altered by roof loads.
NOV
Starting and driving
Adjusting headlamp pattern
A. Headlamp pattern for left-hand traffic
B. Right-hand traffic
Halogen lights
Bi-Xenon lights
Correct light pattern for left or
right-hand traffic
Halogen headlamps
The headlamp control should be in
position (A) for left-hand traffic and
position (B) for right-hand traffic.
Bi-Xenon headlamps
The headlamp control should be in
position (A) for left-hand traffic and
position (B) for right-hand traffic.
The headlamps’ projection can be adjusted
to avoid dazzling other motorists. The correct
pattern will also better illuminate the verge.
WARNING!
On cars with Bi-Xenon headlamps, all
work on the lights should be carried out at
an authorised Volvo workshop.
Bi-Xenon headlamps must be handled
with extreme care due to the high-voltage
unit.
NPM
Wheels and tyres
General
Tyre pressure
Changing wheels
Warning triangle and spare wheel
Removing wheels
Emergency puncture repair
132
135
136
137
139
141
NPN
Wheels and tyres
General
Driving characteristics and tyres
The tyres greatly affect the car’s driving
characteristics. The type of tyre, dimensions,
tyre pressure and speed rating are important
for how the car performs.
When changing tyres, ensure that tyres of the
same type and dimensions, and preferably
also the same make, are fitted to all four
wheels. Follow the recommended tyre
pressures specified on the tyre pressure
label, see page 135.
Designation of dimensions
The dimensions are stated on all car tyres.
Example:
205/55R16 91 W.
205
55
R
16
91
W
Section width (mm)
Ratio between section height and
width (%)
Radial ply
Rim diameter in inches (")
Tyre load index (in this case 615 kg)
Speed rating (in this case 270 km/h)
Speed ratings
The car is approved as a whole, which means
that dimensions and speed ratings must not
differ from those specified on the vehicle’s
registration document. The only exception to
these conditions is winter tyres (both those
with metal studs and those without). If such a
NPO
tyre is chosen, the car must not be driven
faster than the speed rating of the tyre (for
example, class Q can be driven at a maximum
of 160 km/h).
Remember that traffic regulations determine
how fast a car can be driven, not the speed
class of the tyres.
Note! Maximum permitted speeds indicated.
Q
T
H
V
W
Y
160 km/h (used only on winter
tyres)
190 km/h
210 km/h
240 km/h
270 km/h
300 km/h
New tyres
Tyres are perishable. After a
few years they begin to
harden at the same time as
the friction capacity/characteristics gradually deteriorate. Therefore aim to get
as fresh tyres as possible when you replace
them. This is especially important with regard
to winter tyres. The week and year of
manufacture are stated with four digits, for
example 1502. The tyre in the illustration was
manufactured in week 15 of 2002.
Tyre age
Even if tyres have a theoretical lifespan of up
to ten years, it is not recommended to drive
on tyres which are more than six years old.
Wheels and tyres
on the engine variant. When driving on winter
tyres, these must be fitted to all four wheels.
NOTE! Ask a Volvo dealer which rim and tyre
types are most suitable.
Studded tyres
Studded winter tyres should be run in gently
for 500-1000 km so the studs settle properly
into the tyre. This gives the tyre, and
especially the studs, a longer lifespan.
space between the brake disks and the
wheels is too small.
Important!
Use Volvo genuine snow chains or
equivalent chains designed for the car
model, and tyre and rim dimensions.
Consult an authorised Volvo workshop
NOTE! The legal provisions for the use of
studded tyres vary from country to country.
Tyres with tread wear indicators
Tread wear indicators are narrow treadless
bands across the width of the tread. On the
side of the tyre are the letters TWI (tread
wear indicator). When only 1.6 mm of tread
remains, this band is clearly visible. Change
the tyres as soon as possible. Remember that
tyres with little tread depth provide very poor
grip in rain and snow.
Winter tyres
Volvo recommends winter tyres with particular dimensions. These are stated on the
tyre pressure label, see page 135 for its
location. The tyre dimensions are dependent
Tread depth
Road conditions with ice, slush and low
temperatures place considerably higher
demands on tyres than summer conditions. It
is therefore not recommended to drive on
winter tyres that have a tread depth of less
than four millimetres.
Snow chains
Snow chains may only be used on the front
wheels. This also applies to all-wheel-drive
cars.
NOTE! Never drive faster than 50 km/h with
snow chains. Avoid driving on bare ground as
this wears out both the snow chains and
tyres. Never use quick-fit snow chains as the
NPP
Wheels and tyres
General
Steel rims – standard wheel nuts (1)
Steel rims are normally mounted with the
standard wheel nuts, but the bulge acorn
variety may also be used.
WARNING!
Never use standard nuts for aluminium
rims. The wheels can come loose.
Standard (1) and bulge acorn (2) wheel nuts
Rims and wheel nuts
Only use rims that are tested and approved
by Volvo and which are Volvo genuine accessories. There are two types of wheel nut,
depending on whether the rims are made of
steel or aluminium. Tighten the wheel nuts to
85 Nm. Check the torque with a torque
wrench.
Important!
The wheel nuts should be tightened to
85 Nm. Overtightening can damage the
nuts and the bolts.
Aluminium rims – bulge acorn wheel
nuts (2)
Only use the bulge acorn variety of nuts with
aluminium rims. These differ markedly from
other nut types as they have a rotating conical
washer.
Temporary spare
The spare wheel1 is only intended to be used
for the short time it takes to get the ordinary
wheel replaced or repaired. Replace the
spare wheel as soon as possible with a
normal wheel. The car’s handling may be
altered by the use of the spare wheel.
Never drive faster than 80 km/h with a spare
wheel on the car.
Important!
The car must never be driven fitted with
more than one temporary spare wheel.
NOTE! These nuts may also be used with
steel rims.
Locking wheel nuts
Locking wheel nuts can be used on both
aluminium and steel rims. If steel rims with
locking nuts are used in combination with
wheel covers, the locking wheel nut should
be mounted on the bolt nearest the air valve.
Otherwise the wheel cover cannot be fitted
to the rim.
1.
NPQ
Certain variants and markets
Wheels and tyres
Tyre pressure
Checking the tyre pressure
Check the tyre pressure regularly. The
correct tyre pressure is shown in the tyre
pressure table. The stated tyre pressures
refer to cold tyres. (Cold tyres mean the tyres
are the same temperature as the ambient
temperature.)
Recommended tyre pressure
The tyre pressure decal on the inside of the
fuel filler flap shows what pressure the tyres
should have with different load and speed
conditions.
Driving with the wrong tyre pressure
adversely affects the car’s driving characteristics and can increase tyre wear. After just a
few kilometres of driving, the tyres warm up
and the pressure increases. Therefore air
should not be released if the pressure is
checked when the tyres are warm. However
the pressure should be increased if it is
too low.
NPR
Wheels and tyres
Changing wheels
adversely affected. Tyres with the greatest
tread depth should always be fitted to the
rear of the car (to decrease the risk of
skidding).
Wheels should be stored lying down or
hanging up, and not standing up.
Contact an authorised Volvo workshop if you
are uncertain about tread depth.
The arrow shows the tyre’s direction of
rotation.
Summer and winter wheels
When summer and winter wheels are
changed they should be marked with which
side of the car they were mounted on, for
example L for left and R for right. Tyres with a
tread pattern which are designed to only turn
in one direction have the direction of rotation
marked with an arrow. The tyre should always
rotate in the same direction throughout its
lifespan. Tyres should only be switched
between front and rear positions, never
between left and right-hand sides, or vice
versa. If the tyre is mounted incorrectly, the
car’s braking characteristics and capacity to
force rain, snow and slush out of the way are
NPS
Wheels and tyres
Warning triangle and spare wheel
Warning triangle
The warning triangle is fitted on the inside of
the boot lid attached with two clips.
Follow the regulations for the use of a
warning triangle. Place the warning triangle in
a suitable place with regard to the traffic.
– Undo the case containing the warning
triangle, it is attached with Velcro. Take
the warning triangle out of the case.
– Lower the warning triangle’s support legs.
Ensure the warning triangle and its case are
properly secured in the cargo area after use.
NPT
Wheels and tyres
Warning triangle and spare wheel
Spare wheel and jack
The car’s original jack
The original jack should only be used for
changing wheels. The jack’s thread should
always be well greased.
The spare wheel, jack and wheel spanner are
found under the floor in the cargo area.
Taking out the spare wheel:
– Fold the rear edge of the floor mat
forward.
– Release the spare wheel and lift it out.
– Take out the jack and the wheel spanner.
NPU
Putting the spare wheel and jack into
the cargo area:
– Wind the jack to halfway (1). The marking
on the plate (2) should line up with the
marking on the arm (3) so that the jack
can fit lying down in the holder.
– Fold in the handle (4) and place the wheel
spanner (5) on the jack.
– Put the jack back (1) in the hole on the
right (6). Fasten the spare wheel (7) in
the hole on the left (8).
Wheels and tyres
Removing wheels
Set up the warning triangle if a wheel must be
replaced at a busy location. Make sure that
the car and jack are on a firm horizontal
surface.
– Take out the spare wheel, jack and wheel
spanner, which are found under the
carpet in the cargo area.
– Apply the parking brake and engage first
gear, or position P if the car has an
automatic gearbox.
– Place chocks in front of and behind the
wheels which will remain on the ground.
Use heavy wooden blocks or large
stones.
– Cars with steel rims have removable
wheel covers. Prize off the wheel cover
with the end of the wheel spanner, or pull
it off by hand.
– Loosen the wheel nuts ½-1 turn
anticlockwise with the wheel spanner.
– On each side of the car are two jacking
points. Wind down the jack’s base so that
it sits level on the ground. Check that the
jack is seated correctly in the jacking
point, as illustrated, and that the base is
located directly under it.
– Jack up the car high enough that the
wheel is clear of the ground. Remove the
wheel nuts and lift off the wheel.
NPV
Wheels and tyres
Removing wheels
Fitting the wheel
– Clean the contract surfaces on the wheel
and hub.
– Put on the wheel. Tighten the wheel nuts.
– Lower the car so that the wheel cannot
rotate.
– Tighten the wheel nuts crosswise. It is
important that the wheel nuts are
tightened properly. Tighten to 85 Nm.
Check the torque with a torque spanner.
– Put on the wheel cover (steel rim).
WARNING!
Never crawl under the car when it is raised
on the jack.
Passengers must leave the car when it is
raised on the jack.
Ensure that passengers wait with the car or preferably a crash barrier - between
them and the road.
NQM
Wheels and tyres
Emergency puncture repair
General
Cars which do not have a spare wheel are
instead equipped with an emergency
puncture repair kit. This kit can be used to
both seal the puncture and to check and
adjust the tyre pressure. The kit consists of an
electric air compressor and an integrated
canister with sealing liquid.
The canister with the sealing fluid should be
replaced before the best-before date has
expired or after the emergency repair kit has
been used. Puncture repair kit replacement,
see page 146 for canister replacement.
NOTE! The emergency puncture repair kit is
only intended for sealing tyres with a
puncture in the tread.
Emergency puncture repair kit
The emergency puncture repair kit is only
intended to work as a temporary repair so
that the car can be driven a further 200 km
(max.) or to the nearest tyre centre. The
sealing fluid has the ability to effectively seal
tyres which have punctures in the tread.
NQN
Wheels and tyres
Emergency puncture repair
The emergency puncture repair kit has limited
abilities to seal tyres which have punctures in
the wall of the tyre. Do not seal tyres with the
emergency puncture repair kit if they have
larger slits, cracks, irregularities or similar
damage.
The emergency puncture repair kit with
compressor and tools are found under the
floor in the cargo area.
12 V sockets for the compressor are located
by the centre console in the front, by the rear
seat and in the cargo area. Choose the
electrical socket that is nearest the punctured
tyre.
WARNING!
The sealing fluid may cause irritation if it
comes into direct contact with skin. In
the case of contact with skin, wash away
the fluid with soap and water.
Taking out the emergency puncture
repair kit
– Fold away the rear edge of the floor mat
forward.
– Lift up the emergency puncture repair kit.
NQO
Wheels and tyres
Inflating tyres
Set up the warning triangle if a tyre must be
inflated in an area close to traffic.
– Ensure that the orange switch (2) is in
position 0 and take out the lead (5) and
air hose (4) from the side
compartment (3).
– Screw the air hose’s valve connection to
the bottom of the thread on the tyre’s air
valve.
– Connect the lead (5) to one of the car’s
12 V sockets.
– Start the engine. The car must be in a
well-ventilated place.
– Start the compressor by flicking the
switch (2) to position I.
– Pump up the tyre to the pressure
specified on the tyre pressure label.
– Turn off the compressor, the switch (2)
should be in position 0. Detach the air
hose and unplug the lead. Replace the
valve’s dust cap.
– Put the lead (5) and air hose (4) into the
side compartment (3).
– Put the puncture repair kit back under the
floor in the cargo area.
– The compressor should not run for more
than ten minutes at a time. Let it cool
afterwards as there is a risk of
overheating.
– Objects with a volume of up to 50 litres
can be pumped up with the compressor.
WARNING!
Inhaling car exhaust fumes can result in
danger to life. Never leave the engine
running in sealed areas or areas that lack
sufficient ventilation.
NQP
Wheels and tyres
Emergency puncture repair
Sealing punctured tyres
Set up the warning triangle if emergency tyre
repairs must be carried out in an area where
there is other traffic.
– Remove the decal (1) regarding the
highest permitted speed from the
emergency puncture repair kit and stick it
on the steering wheel where it can be
clearly seen by the driver.
– Ensure that the orange switch (2) is in
position 0 and take out the lead (5) and
air hose (4) from the side
compartment (3).
– Screw the air hose’s valve connection to
the bottom of the thread on the tyre’s air
valve.
NQQ
– Connect the lead (5) to one of the car’s
12 V sockets.
– Release the safety catch (6) and turn the
orange-coloured part (7) 90 degrees to
the vertical position, until a click is heard.
– Start the engine. The car must be in a
well-ventilated place.
WARNING!
Inhaling car exhaust fumes can result in
danger to life. Never leave the engine
running in sealed areas or areas that lack
sufficient ventilation.
– Start the compressor by flicking the
switch (2) to position I. The pressure may
increase temporarily up to a maximum of
4 bar while the sealing liquid is being
pumped in. After about one minute, the
pressure will drop and the pressure
gauge show a more correct tyre pressure.
– Pump the tyre to a pressure of between
1.8 bar and 3.5 bar. If the pressure does
not reach 1.8 bar after ten minutes of
pumping, the compressor should be
turned off so it does not overheat.
– Undo the air hose (4) from the air valve
and put the dust cap back on. Unplug the
lead (5) from the electrical socket. Fold
the orange-coloured part (7) back into its
original position and secure the catch (6).
Keep the emergency repair kit in a safe
place in the car.
Wheels and tyres
WARNING!
Never stand next to the tyre when the
compressor is running. Be particularly
observant of the tyre walls. If cracks,
irregularities or other damage appears,
turn off the compressor immediately.
Under these circumstances your journey
should not continue. Contact an
authorised tyre centre.
– Immediately drive about 3 km, at a
maximum speed of 80 km/h, to allow the
sealing fluid to seal the tyre well.
WARNING!
You should not drive faster than 80 km/h
after the emergency tyre repair kit has
been used. The temporarily sealed tyre
must be changed as soon as possible
(maximum driving distance: 200 km).
– Check the tyre pressure again:
NOTE! Do not raise the orange-coloured
part (7) when only the compressor is to be
used for inflation.
the compressor. If the tyre pressure is
below 1.3 bar, the tyre has not been sufficiently well sealed. The journey should
not be continued under these circumstances. Contact a tyre centre.
– If the tyre pressure is higher than 1.3 bar,
the tyre should be pumped up to the
pressure stated on the tyre pressure
label, see page 135 for its location.
Release pressure with the reduction
valve (8) if the tyre pressure is too high.
– Turn off the compressor, the switch (2)
should be in position 0. Detach the air
hose and unplug the lead. Replace the
valve’s dust cap.
– Put the lead (5) and air hose (4) into the
side compartment (3).
– Put the puncture repair kit back under the
floor in the cargo area.
The compressor should not run for more than
ten minutes at a time. Let it cool afterwards as
there is a risk of overheating.
NOTE! The canister with sealant and hose
should be replaced after use.
– Connect the air hose (4) to the air valve
on the tyre. Connect the lead (5) to the
12 V power point. Read the pressure on
NQR
Wheels and tyres
Emergency puncture repair
Changing the sealing fluid
canister
The canister of sealing fluid should be
changed before the best-before date has
expired, see date label (1), or after the tyre
has been sealed. After use, the canister (6)
with holder (8) and air hose (10) should be
changed.
The canister can be replaced by an authorised Volvo workshop or according to the
instructions.
Important!
Read the safety instructions on the
bottom of the canister.
NQS
WARNING!
Ensure the compressor is not connected
to the 12 V socket when the canister is
changed.
Changing the canister before the
best-before date has expired
– Undo the two screws (2) on the orangecoloured case (3).
– Remove the speed label (4) and date
label (1), and open the safety catch (5).
Loosen the case (3) and take it off.
– Unscrew and remove the canister (6).
– Check that the seal (7) on the new
canister is not damaged. Screw the
canister into place.
– Refit the case (3). Check that the case is
correctly fitted. Screw it on with the
screws (2).
– Affix the speed label (4) and new date
label (1) to the tyre repair kit.
Treat the removed canister as hazardous
waste.
Changing the canister and hose after
use
– Undo the two screws (2) on the orangecoloured case (3).
Wheels and tyres
– Remove the speed label (4) and date
label (1), and open the safety catch (5).
Loosen the case (3) and take it off.
– Push down the button (8) while turning
the canister (6) and the holder (9)
clockwise. Remove them.
– Pull out the air hose (10).
– Wipe off remaining sealing fluid with a rag
or scrape it away if it is has already dried.
– Fit a new air hose (10). Check that it is
fitted correctly.
Check that the seal (7) on the new canister is
not damaged. Screw the holder (9) onto the
canister (6) and turn it anticlockwise until a
click is heard.
– Refit the case (3). Check that the case is
correctly fitted. Screw it on with the
screws (2).
– Affix the speed label (4) and new date
label (1) to the tyre repair kit.
The empty canister and air hose can be
treated as normal waste.
NQT
Wheels and tyres
NQU
Car care
Cleaning
Touching up paintwork
Rustproofing
150
152
153
NQV
Car care
Cleaning
Washing the car
Wash the car as soon as it becomes dirty.
Use car shampoo. Dirt and road salt can lead
to corrosion.
• Do not park the car in direct sunshine.
Washing a car with hot paintwork can
cause permanent paintwork damage.
Wash the car in a carwash with waste
water separator.
• Thoroughly rinse dirt off the underbody of
the car.
• Rinse the entire car to remove loose dirt.
When using a pressure washer: Make
sure that the nozzle of the pressure
washer is not closer than 30 cm to the
bodywork. Do not spray directly at the
locks.
• Wash using a sponge, car shampoo and
plenty of lukewarm water.
• If the dirt is difficult to dislodge, wash the
car using a cold degreasing agent.
• Dry the car using a clean, soft chamois or
a water scraper.
• Clean the wiper blades with a lukewarm
soap solution or car shampoo.
Removing bird droppings
Wash bird droppings off the paintwork as
soon as possible. Bird droppings contain
chemicals that affect and discolour paintwork
NRM
very quickly. This discoloration can only be
removed by a specialist.
WARNING!
Always have the engine cleaned by a
workshop. There is a risk of fire if the
engine is hot.
Automatic carwashes
Although an automatic carwash is a quick
and easy way to clean the car, it is no
substitute for a proper hand wash. The
brushes of an automatic carwash cannot
reach all parts. We recommend that new cars
are washed by hand for the first few months.
WARNING!
Always test the brakes after washing the
car to ensure that moisture and corrosion
do not attack the brake pads and reduce
braking performance.
Press the brake pedal lightly from time to time
if driving for long periods in rain or slush. This
heats and dries the brake pads. You should
also do this when you begin driving in
extremely damp or cold weather.
Cleaning the upholstery
Treating spots on fabric
A special cleaning agent, available from your
Volvo dealer, is recommended for cleaning
the fabric upholstery. Other chemicals can
impair the fire retardant qualities of the upholstery.
Important!
Sharp objects and Velcro may damage
the fabric upholstery.
Treating spots on vinyl and plastic parts
A special cleaning agent, available from your
Volvo dealer, is recommended for cleaning
interior vinyl and plastic parts. Do not scrape
or rub spots. Do not use strong stain
removers.
Treating spots on leather
A special cleaning agent, available from your
Volvo dealer, is recommended when cleaning
leather upholstery. Treat the leather upholstery once or twice a year using Volvo’s
leather care kit. Never use strong solvents.
Such products may damage fabric, vinyl and
leather upholstery.
Car care
Cleaning seatbelts
Use water and a synthetic detergent. A
special textile cleaning agent is available from
you Volvo dealer. Make sure the seatbelt is
dry before allowing it to retract.
Polishing and waxing
Polish and wax the car if the paintwork is dull
or to give the paintwork extra protection.
The car does not need to be polished until it
is at least one year old. However, the car can
be waxed during this time. Do not polish or
wax the car in direct sunlight.
Wash and dry the car thoroughly before you
begin polishing or waxing. Clean off asphalt
and tar stains using Volvo tar remover or
white spirit. More stubborn marks can be
removed using fine rubbing paste designed
for car paintwork.
Polish first with a polish and then wax with
liquid or solid wax. Follow the instructions on
the packaging carefully. Many preparations
contain both polish and wax.
NRN
Car care
Touching up paintwork
– Stir the primer well and apply using a fine
brush or matchstick. Apply paint using a
brush once the primer is dry.
– For scratches, proceed as above, but
mask around the damaged area to protect
the undamaged paintwork.
– After a few days, polish the touched-up
areas. Use a soft rag and a small amount
of lapping paste.
Paintwork
Paint is an important part of the car’s
rustproofing and should therefore be
checked regularly. To avoid the onset of rust,
damaged paintwork must be rectified
immediately. The most common types of
paintwork damage are stone chips,
scratches, and marks on the edges of wings
and doors.
Colour code
It is important that the correct colour is used.
The car’s colour code is shown on the
product decal on the B-pillar. See page 208.
Stone chips and scratches
Before touching up paintwork, the car must
be clean and dry and at a temperature
above 15 °C.
NRO
Materials
• Primer in a can
• Paint in a can or touch-up pen
• Brush
• Masking tape
Minor stone chips and scratches
If the stone chip has not penetrated to the
bare metal and there is an undamaged colour
coat, you can paint straight after cleaning the
damaged area.
If the stone chip has penetrated to the
bare metal
– Stick a piece of masking tape over the
damaged surface. Then remove the tape
to remove any loose paint.
Car care
Rustproofing
Inspection and maintenance
Your car received a thorough and complete
rustproofing at the factory. Parts of the body
are made of galvanised sheet metal. The
underbody is protected by a wear-resistant
anti-corrosion compound. And, a thin,
penetrating rustproofing fluid was sprayed
into the members, cavities and closed
sections.
Maintain the car’s rustproofing.
• Keep the car clean. Hose down the
underbody. If using a pressure washer,
keep the nozzle at least 30 cm from the
painted surfaces.
• Regularly check and touch-up the
rustproofing treatment as necessary.
The car’s rustproofing does not normally
require treatment for approximately 12 years.
After that time, it should be treated at threeyear intervals. If the car needs further
treatment, please contact an authorised
Volvo workshop.
NRP
Car care
NRQ
Maintenance and service
Volvo service
Self-maintenance
Bonnet and engine compartment
Diesel
Oils and fluids
Wiper blades
Battery
Replacing bulbs
Fuses
156
157
158
159
160
164
165
167
173
NRR
Maintenance and service
Volvo service
Volvo service programme
Installing accessories
Before the car left the factory, it was
thoroughly test driven. It was checked again
in accordance with Volvo Car Corporation
regulations before it was handed over to you.
The incorrect connection and installation of
accessories can negatively affect the car’s
electrical system. Certain accessories only
function when the appropriate software has
been programmed into the car’s electrical
system. Always contact an authorised Volvo
workshop before installing accessories which
are connected to or affect the electrical
system.
To keep your Volvo as safe and reliable as
possible, follow the Volvo service programme
specified in the Service and Warranty
Booklet. Have an authorised Volvo workshop
carry out service and maintenance work.
Volvo workshops have the personnel, special
tools and service literature to guarantee the
highest quality of service.
Important!
For the Volvo warranty to apply, check
and follow the instructions in the Service
and Warranty Booklet.
Special service measures
Certain service measures, which affect the
car’s electrical system, can only be performed
using electronic equipment specially
developed for your car. Always contact an
authorised Volvo workshop before beginning
or performing service work that affects the
electrical system.
NRS
Recording vehicle data
One or more of the computers in your Volvo
are capable of recording detailed information.
This information is intended for use in
research to enhance safety and for
diagnosing faults in some of the in-car
systems. The data may include details
regarding seatbelt use by the driver and
passengers, the functions of various vehicle
systems and modules, and status information
about the engine, throttle, steering, brakes
and other systems. This data can also include
details of the way the car is driven. This type
of information can include, without being
limited to, specific details such as vehicle
speed, the use of the brake and accelerator
pedals and steering wheel position. This latter
type of data can be stored for a limited period
while the car is being driven and subsequently during a collision or a near-collision.
Volvo Car Corporation will not disclose the
stored information without consent. However,
Volvo Car Corporation may be forced to
disclose the information due to national legislation. Volvo Car Corporation and its
workshops may also read and use the information.
Adverse driving conditions
Change the engine oil and replace the air and
oil filters more often than recommended in the
Service and Warranty Booklet when driving in
adverse conditions.
Adverse driving conditions include extended
periods of driving:
•
•
•
•
•
•
in a dusty or sandy environment.
towing a caravan or trailer.
in mountainous regions.
at high speeds.
at low speeds or idling.
short journeys (less than 10 km) at low
temperatures (below 5 ºC).
Maintenance and service
Self-maintenance
Before starting work on the car
Check regularly
Battery
• Check that the battery cables are
correctly connected and tightened.
• Never disconnect the battery when the
engine is running (e.g. if replacing the
battery).
• Never use a quick charger to charge the
battery. The battery cables must be
disconnected when charging the battery.
The battery contains acid that is both
corrosive and toxic. Handle the battery in an
environmentally-suitable way. Let your Volvo
dealer assist you.
Check the following at regular intervals, for
example, when refuelling:
• Coolant – The level must be between the
MIN and MAX marks on the expansion
tank.
• Engine oil – The level must be between
the MIN and MAX marks.
• Power steering fluid – The level must be
between the MIN and MAX marks.
• Washer fluid – The reservoir should be
well filled. Use washer antifreeze at
temperatures around freezing.
• Brake and clutch fluid – The level must be
between the MIN and MAX marks.
WARNING!
High voltage output from the ignition
system. The voltage in the ignition system
is dangerous. The ignition must therefore
always be switched off for work in the
engine compartment.
Do not touch the spark plugs or ignition
coils when the ignition is on or the engine
is hot.
WARNING!
Bear in mind that the radiator fan may start
automatically some time after the engine
has been switched off.
Always have the engine cleaned by a
workshop. There is a risk of fire if the
engine is hot.
NRT
Maintenance and service
Bonnet and engine compartment
Opening the bonnet
Engine compartment
To open the bonnet:
1.
2.
3.
Washer fluid reservoir (4 cyl.)
Coolant expansion tank
Power steering fluid reservoir
4.
5.
6.
7.
8.
Engine oil dipstick1
Radiator
Radiator fan
Washer fluid reservoir (5 cyl.)
Brake and clutch fluid reservoir
(right-hand drive)
– Pull the handle on the far left under the
dashboard. You will hear when the catch
releases.
– Insert your hand under the centre of the
front edge of the bonnet and press the
safety catch to the right.
– Open the bonnet.
WARNING!
Check that the bonnet locks properly
when closed.
9. Filler orifice for engine oil1
10. Brake and clutch fluid reservoir
(left-hand drive)
11. Battery
1.
NRU
Dependent on engine variant.
12. Relay and fuse box
13. Air filter1
Maintenance and service
Diesel
Fuel system
Empty tank
Diesel engines are sensitive to contaminants.
Only use diesel from a well-known oil
company. Never fill up with diesel if the quality
is dubious. The large oil companies also
produce a special winter-grade diesel for
temperatures around freezing. This fuel is less
viscous at low temperatures and reduces the
risk of wax forming in the fuel system.
No special procedures are required if the tank
runs dry.
The risk of condensation in the fuel tank is
reduced if the tank is kept well filled. When
refuelling, check that the area around the fuel
filler pipe is clean. Avoid spilling fuel onto the
paintwork. Wash off any spillage with
detergent and water.
There is a risk of engine damage if the
RME concentration is greater than 5 %.
RME (Rape methyl ester)
A maximum of 5 % RME may be mixed with
the diesel.
Important!
Draining condensation from the
fuel filter
The fuel filter separates condensation from
the fuel. Condensation can disrupt engine
operation.
The fuel filter must be drained at the intervals
specified in the Service and Warranty Booklet
or if you suspect that the car has been filled
with contaminated fuel.
NRV
Maintenance and service
Oils and fluids
Dipstick, petrol engines
Dipstick, diesel engine
Checking and changing the
engine oil and oil filter
The oil level in a new car must be checked
during the period preceding the first regular
oil change. The Service and Warranty Booklet
specifies the odometer readings for oil
changes. Volvo recommends checking the oil
level every 2500 km. The most accurate
measurements are made on a cold engine
before starting. The measurement will be
inaccurate if taken immediately after the
engine is switched off. The dipstick will
indicate that the level is too low because the
oil has not had time to flow down into the oil
sump.
The Service and Warranty Booklet specifies
suitable intervals for changing the oil and oil
filter. Shorter intervals are recommended if
driving in adverse conditions. See page 156.
Check the level of engine oil and change the
oil regularly.
NOTE! See the recommended oil grade,
viscosity and capacities on page 212.
NSM
The oil level must be within the area marked
on the dipstick.
Important!
Always use oil of the recommended grade
and correct viscosity.
Never use oil additives. These can
damage the engine. If the system is
topped up with a different oil, contact the
nearest authorised Volvo workshop for
servicing.
Maintenance and service
Checking the oil in a cold engine:
– Wipe the dipstick clean before checking
the level.
– Check the oil level using the dipstick. The
oil level must be between the MIN and
MAX marks.
– If the level is close to the MIN mark, start
by topping up with 0.5 litres of oil. Top up
until the oil level is nearer the MAX than
the MIN mark on the dipstick. See
page 212 for capacities.
Checking the oil in a warm engine:
– Park the car on a level surface, switch off
the engine and wait 10-15 minutes to
allow the oil time to run back to the sump.
– Wipe the dipstick clean before checking
the level.
– Check the oil level using the dipstick. The
oil level must be between the MIN and
MAX marks.
– If the level is close to the MIN mark, start
by topping up with 0.5 litres of oil. Top up
until the oil level is nearer the MAX than
the MIN mark on the dipstick. See
page 212 for capacities.
Important!
Never fill above the MAX mark. Oil
consumption may increase if too much oil
is poured into the engine.
WARNING!
Do not spill oil onto the hot exhaust
manifold due to the risk of fire.
Location of washer fluid reservoir1
Washer fluid, topping up
The windscreen and headlamp washers
share a common reservoir.
1.
Filler cap on 4 cylinder engines and
diesel.
2. Filler cap on 5 cylinder engines.
Add washer antifreeze during the winter so
that the fluid does not freeze in the pump,
reservoir and hoses. See the capacities on
page 213.
NOTE! Mix the washer antifreeze and water
before filling the reservoir.
1. Dependent on engine variant.
NSN
Maintenance and service
Oils and fluids
See the capacities on page 213.
Check the coolant regularly
The level should lie between the MIN and
MAX marks on the expansion tank. If the
system is not filled sufficiently, high local
temperatures could occur, causing a risk of
damage (cracks) to the cylinder head. Top up
the coolant when the level falls to the MIN
mark.
NOTE! The engine must only be run with a
well-filled cooling system. High temperatures
can occur, causing a risk of damage (cracks)
to the cylinder head.
Checking and topping up the
coolant
When topping up the coolant, follow the
instructions on the packaging. It is important
that the mixture of coolant concentrate and
water is correct for the prevailing weather
conditions. Never top up with water only. The
risk of freezing increases with both too little
and too much coolant concentrate.
Important!
Always use coolant with anti-corrosion
agent as recommended by Volvo. New
cars are filled with coolant that can
withstand temperatures down to
approximately -35 °C.
NSO
WARNING!
The coolant may be very hot. If the coolant
requires topping up when the engine is at
operating temperature, unscrew the
expansion tank cap slowly to gently
release the overpressure.
Checking and topping up the
brake and clutch fluid
The brake and clutch fluid have a common
reservoir1. The fluid level must be between
the MIN and MAX marks. Check the level
regularly. Change the brake fluid every other
year or at every other regular service.
See the capacities and recommended fluid
grade on page page 213.
The fluid should be changed annually on cars
driven in conditions requiring hard, frequent
1.
Location dependent on whether car is
left or right-hand drive.
Maintenance and service
braking, such as driving in mountains or
tropical climates with high humidity.
WARNING!
If the brake fluid is under the MIN level in
the brake fluid reservoir, do not drive
further before topping up the brake fluid.
The reason for the loss of brake fluid must
be investigated.
Checking and topping up the
power steering fluid
Check the level at every service. The fluid
does not require changing. The fluid level
must be between the MIN and MAX marks.
See the capacities and recommended oil
grade on page 213.
If a fault should arise in the power steering
system or if the car is without power and must
be towed, it can still be steered. However the
steering will be much heavier than normal and
it will require more effort to turn the wheel.
NSP
Maintenance and service
Wiper blades
Changing the wiper blades
– Lift up the wiper arm and position the
wiper blade at 90 degrees to the wiper
arm.
– Pull the wiper blade off the shaft, straight
out to the side.
– Fit the new wiper blade (1), at 90 degrees
to the wiper arm.
– Position the wiper blade (2) under the
curved metal plate (3) and lower the wiper
arm.
NOTE! The wiper blades are different
lengths. The blade on the driver’s side is
longer than the blade on the passenger side.
NSQ
Maintenance and service
Battery
NOTE! Never fill above the maximum
mark (A).
Important!
Always use distilled or deionised water
(battery water).
• Tighten the caps properly.
NOTE! The life of the battery is shortened if it
becomes discharged repeatedly.
Symbols on the battery
These symbols displayed on the battery.
Battery care
The battery contains
corrosive acid.
Avoid sparks and naked
flames.
Risk of explosion.
Use protective goggles.
The service life and function of the battery is
influenced by factors such as the number of
starts, discharging, driving style, driving
conditions and climatic conditions.
For the battery to function satisfactorily,
consider the following:
Further information in the
owner’s manual.
• Regularly check that the battery
electrolyte level is correct (A).
• Check all cells. Use a screwdriver to
remove the caps. Each cell has its own
maximum level mark.
• If necessary, top up with distilled water to
the battery’s maximum mark.
Store the battery out of the
reach of children.
NSR
Maintenance and service
Battery
Changing the battery
Removing the battery:
– Switch off the ignition and remove the key.
– Unscrew the cover over the battery.
– Wait at least 5 minutes before touching
any electrical terminals. This allows time
for the information in the car’s electrical
system to be stored in the control
modules.
– Remove the lid and unscrew the front wall
of the battery box using a screwdriver.
– Disconnect the negative battery lead.
– Release the clamp securing the battery.
– Disconnect the positive battery lead.
– Remove the battery.
Fitting the battery:
– Fit the battery into position.
– Connect the positive lead.
– Fit the clamp securing the battery.
– Connect the negative lead.
– Refit the front wall of the battery box and
the lid.
– Refit the cover over the battery.
NSS
WARNING!
Batteries can generate oxyhydrogen gas,
which is highly explosive. A spark, which
can be generated if you connect the jump
leads incorrectly, is sufficient to make the
battery explode. The battery also contains
sulphuric acid, which can cause serious
burns. If the acid comes into contact with
eyes, skin or clothing, flush with large
quantities of water. If acid splashes into the
eyes, seek medical advice immediately.
Maintenance and service
Replacing bulbs
General
All bulb specifications are given on page 219.
The following list contains bulbs and pointsource lamps that are specialised or unsuitable for changing except at a workshop:
•
•
•
•
•
•
General interior lighting in the roof.
Reading lamps.
Glovebox lighting.
Direction indicators in the door mirrors.
Approach lighting in the door mirrors.
High-level brake light.
Important!
Never touch the bulbs glass with your
fingers. Grease and oils from your fingers
are vaporised by the heat, coating and
damaging the reflector.
Changing front bulbs
All front bulbs (except for fog lamps) are
changed by first removing the lamp housing
from the engine compartment.
WARNING!
Removing the lamp housing:
– Remove the ignition key and turn the light
switch to position 0.
– Withdraw the lamp housing’s locking
pin (1).
– Pull the lamp housing to the side and then
forward (2).
– Unplug the connector.
– Lift out the lamp housing and place it on a
soft surface to avoid scratching the lens.
Fitting the lamp housing:
– Plug in the connector.
– Refit the lamp housing and fit the locking
pin. Check that the pin is correctly
inserted.
– Check the lighting.
The lamp housing must be plugged in and
secured in place before the lighting is turned
on or the ignition key inserted into the ignition
switch.
On cars with Bi-Xenon headlamps, all
work on the lights should be carried out at
an authorised Volvo workshop.
Bi-Xenon headlamps must be handled with
extreme care due to the high-voltage unit.
NST
Maintenance and service
Replacing bulbs
Dipped beam
Fitting a new bulb:
Main beam
Removing the cover and bulb:
– Fit the new bulb. It can only be fitted in
one position.
– Press the spring clip up and then slightly
to the right so that it clicks into place.
– Press the connector back on.
– Refit the plastic cover.
– Refit the lamp housing.
– Remove the entire lamp housing.
– Left-hand headlamp:
Turn the bulb holder anticlockwise.
Right-hand headlamp:
Turn the bulb holder clockwise.
– Withdraw the bulb holder and change the
bulb.
– Refit the bulb holder. It can only be fitted
in one way.
– Refit the lamp housing.
– Remove the entire lamp housing.
– Bend aside the catches and remove the
cover.
– Unplug the connector from the bulb.
– Release the spring clip that secures the
bulb. First, press it to the left to release it,
then out and down.
– Pull out the bulb.
– Refit the lamp housing.
NSU
Maintenance and service
Position/parking lamps
Direction indicators
Side marker lamps
– Pull out the bulb holder with a pair of
pliers. Do not pull out the bulb holder by
pulling the electrical cable.
– Replace the bulb.
– Press the bulb holder back into place. It
can only be fitted in one way.
– Twist the bulb holder anticlockwise and
remove it.
– To remove the bulb from the bulb holder,
press the bulb in and turn it anticlockwise.
– Fit a new bulb and refit the bulb holder
into the lamp housing.
– Twist the bulb holder anticlockwise and
withdraw it. Change the bulb.
– Refit the bulb holder. It can only be fitted
in one way.
NSV
Maintenance and service
Replacing bulbs
– Press the bulb holder back into place and
refit the cover.
Fog lamps
Removing the bulb holder
– Switch off all lights and turn the ignition
key to position 0.
– Remove the panel from around the lamp
housing.
– Remove the two Torx screws securing the
lamp housing and take out the lamp
housing.
– Unplug the connector from the bulb.
– Turn the bulb anticlockwise and pull it out.
– Fit the new bulb and turn it clockwise.
– Plug in the connector to the bulb.
– Secure the lamp housing with the screws
and press the panel back into place.
All bulbs in the rear lamp cluster can be
changed from inside the cargo area.
NTM
– Switch off all lights and turn the ignition
key to position 0.
– Remove the covers from the left/right
panel to access the bulbs.
– These bulbs are located in separate bulb
holders.
– Unplug the connector from the bulb
holder.
– Squeeze together the catches and
remove the bulb holder.
– Replace the bulb.
– Plug in the connector.
Maintenance and service
Bulb holder
Location of the bulbs in the rear
light cluster
1. Brake light
2. Position/parking lamps
3. Direction indicator
4. Rear fog lamp (one side)
5. Reversing lamp
NOTE! If the error message "BULB
FAILURE"/"CHECK STOP LAMP" remains
after a faulty lamp has been replaced then an
authorised Volvo workshop needs to be
consulted to rectify the fault.
Number plate lighting
Courtesy lighting
– Switch off all lights and turn the ignition
key to position 0.
– Remove the screw with a screwdriver.
– Carefully detach the entire lamp housing
and withdraw it. Turn the connector
anticlockwise and pull out the bulb.
– Replace the bulb.
– Insert the connector and turn clockwise.
– Refit the entire lamp housing and screw it
into place.
There is courtesy lighting under the
dashboard on the driver and passenger
sides.
– Insert a screwdriver and gently turn so
that the lens detaches.
– Remove the blown bulb.
– Fit a new bulb.
– Refit the lens.
NTN
Maintenance and service
Replacing bulbs
Fitting the mirror glass:
– First, press the three lugs at top edge of
mirror glass back into position.
– Then press the three lower lugs back into
position.
Cargo area
Vanity mirror lighting
– Insert a screwdriver and gently turn so
that the lamp housing comes loose.
– Remove the blown bulb.
– Fit a new bulb.
Removing the mirror glass:
NTO
– Insert a screwdriver underneath the lower
edge, in the centre. Carefully prise up the
lug on the edge.
– Insert the screwdriver underneath the
edge on the left and right-hand sides (by
the black rubber sections). Carefully prise
free the lower edge of the glass.
– Carefully detach and lift aside the entire
mirror glass and cover.
– Remove the blown bulb and replace it
with a new one.
Maintenance and service
Fuses
General
All electrical functions and components are fused to protect the car’s
electrical system from damage by short circuiting and overloading.
The fuses are in two different locations in the car:
• Relay/Fuse box in the engine compartment.
• Relay/fuse box in the passenger compartment.
Changing
If an electrical component or function does not work, it may be
because the component’s fuse was temporarily overloaded and blew.
– Look in the fuse diagram to locate the fuse.
– Pull out the fuse and check from the side to see whether the
curved wire has blown.
– If this is the case, replace it with a new fuse of the same colour
and amperage.
Each fuse box has space for several spare fuses. If the same fuse
blows repeatedly it means that there is a fault in the component.
Contact an authorised Volvo workshop to have the system checked.
Relay/fuse box in the engine compartment
The fuse box has 36 fuse positions. Be sure to replace a blown fuse
with a new fuse of the same colour and amperage.
• 19—36 are of the "Mini Fuse" type.
• Fuses 7—18 are of the "JCASE" type and should be replaced by
an authorised Volvo workshop.
• Fuses 1—6 are of the "Midi Fuse" type and may only be replaced
by an authorised Volvo workshop.
On the inside of the cover are tweezers to assist removing and fitting
fuses.
NTP
Maintenance and service
Fuses
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
NTQ
Radiator fan................................................................................... 50 A
Power steering.............................................................................. 80 A
Supply to passenger compartment fuse box......................... 60 A
Supply to passenger compartment fuse box......................... 60 A
Heating and ventilation unit,
Additional heater relay coil (PTC) (only 4 cyl petrol) ........... 80 A
Glow plugs (diesel) ..................................................................... 60 A
ABS pump..................................................................................... 30 A
ABS valves .................................................................................... 20 A
Engine control module (ECM) .................................................. 30 A
Ventilation fan................................................................................ 40 A
Headlamp washers...................................................................... 20 A
Supply to heated rear window.................................................. 30 A
Starter motor relay....................................................................... 30 A
Trailer wiring .................................................................................. 40 A
Reserve .................................................................................................. -
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
Supply to infotainment system ................................................. 30 A
Windscreen wipers ..................................................................... 30 A
Supply to passenger compartment fuse box ........................ 40 A
Reserve .................................................................................................. Horn ................................................................................................ 15 A
Fuel-driven additional heater, passenger
compartment heater.................................................................... 20 A
SUBWOOFER ............................................................................ 15 A
Engine control module (ECM)/
Transmission control module (TCM) ....................................... 10 A
Diesel filter heater........................................................................ 20 A
Reserve .................................................................................................. Ignition switch............................................................................... 15 A
A/C compressor........................................................................... 10 A
Climate control module (CCM)
Multimedia module (MMM) ....................................................... 10 A
Maintenance and service
29.
30.
31.
32.
33.
34.
35.
36.
Fog lamp, front.............................................................................. 15 A
Engine control module (ECM) .....................................................3 A
Alternator voltage regulator ....................................................... 10 A
Injectors (5 cyl), oxygen sensor (4 cyl)
intercooler (diesel), air preheater valve (diesel) .................... 10 A
Oxygen sensor heater element (5 cyl),
vacuum pump (5 cyl)................................................................... 20 A
Ignition coils, injectors (1.6 petrol)
fuel pump (diesel)
pressure switch, climate control (5 cyl) .................................. 10 A
Engine sensor valves, A/C relay
oil trap PTC element, injectors (1.8 petrol)............................ 15 A
Engine control module (ECM), accelerator pedal
position sensor ............................................................................. 10 A
NTR
Maintenance and service
Fuses
Relay/fuse box in the passenger compartment
The fuse box has 50 fuse positions. The fuses are located under the
glovebox. The box also provides space for several spare fuses.
Changing fuses:
– Remove the trim concealing the fuse box by pressing in the pin in
the centre of the clips (1) about 1 cm and then withdrawing the
clips.
– Turn the two wing screws (that secure the fuse box) (2)
anticlockwise and remove them.
– Lower the fuse box (3) half way. Pull it towards the seat until it
stops. Lower it completely. The fuse box can be unhooked.
– Close the fuse box in the reverse order.
– Remove the pins from the centre of the clips. Fit the trim and the
clips. Reinsert the pins to expand the clips and secure the trim.
NTS
Maintenance and service
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
Reserve .................................................................................................. Reserve .................................................................................................. Reserve .................................................................................................. Reserve .................................................................................................. Reserve .................................................................................................. Reserve .................................................................................................. Telephone, audio .......................................................................... 15 A
SRS system .................................................................................. 10 A
Electrical socket, rear seat......................................................... 15 A
Passenger compartment, glovebox and courtesy lighting.....5 A
Sunroof relay coil, door mirrors....................................................5 A
Washer ........................................................................................... 15 A
SRS system .................................................................................. 10 A
Reserve .................................................................................................. -
51. Auxiliary heater relay coil (PTC), front lights
parking assistance....................................................................... 10 A
52. ABS system ..................................................................................... 5 A
53. Power steering ............................................................................. 10 A
54. Transmission control module (TCM),
differential gear (DEM) ............................................................... 10 A
55. Remote control module, Keyless control module................. 20 A
56. Battery charging control module.............................................. 10 A
57. Computer system, brake light switch...................................... 15 A
58. Main beam (right), extra lights relay coil................................ 7.5 A
59. Main beam, left ............................................................................ 7.5 A
60. Seat heating (driver’s side) ....................................................... 15 A
61. Seat heating (passenger side) ................................................. 15 A
62. Sunroof .......................................................................................... 20 A
63. Supply to rear right door............................................................ 20 A
64. Audio ................................................................................................. 5 A
NTT
Maintenance and service
Fuses
65. Infotainment system .......................................................................5 A
66. Infotainment control module (ICM),
infotainment relay coil10 A
67. Reserve .................................................................................................. 68. Cruise control ..................................................................................5 A
69. Climate control, rain sensor..........................................................5 A
70. Reserve .................................................................................................. 71. Reserve .................................................................................................. 72. Reserve .................................................................................................. 73. Sunroof, overhead console (OHC)
rear seatbelt reminder....................................................................5 A
74. Fuel pump relay ............................................................................ 15 A
75. Reserve .................................................................................................. 76. Reserve .................................................................................................. 77. Electrical socket in cargo area, accessory
electronic module (AEM) ........................................................... 15 A
78. Reserve .................................................................................................. 79. Reversing lamp................................................................................5 A
80. Reserve .................................................................................................. 81. Supply to rear left door............................................................... 20 A
82. Supply to front right door........................................................... 25 A
83. Supply to front left door ............................................................. 25 A
84. Power passenger seat................................................................ 25 A
85. Power driver’s seat ...................................................................... 25 A
86. Interior lighting relay, power seats ..............................................5 A
NTU
Infotainment system
Audio and telephone
Control panel
Audio functions
Radio functions
CD/MD (option)
CD changer (option)
Menu settings and options — Audio
Telephone (option)
Telephone functions
Menu settings and options — Telephone
180
181
183
185
190
192
194
196
198
204
NTV
Infotainment system
Audio and telephone
Audio and telephone system
(option)
The infotainment system integrates the audio
and telephone functions. The infotainment
system can be used easily and conveniently
using the common control panel and the
steering wheel keypad. The control panel
display indicates the present function.
The system can be equipped with Dolby
Surround Pro Logic II (certain markets). This
feature gives more natural sound reproduction.
There are three levels of audio system:
• Performance:
AM/FM radio, CD player, 4x20 W, four
full range loudspeakers (or four full range
speakers and two tweeters on certain
markets).
• High Performance:
AM/FM radio, CD player, 4x40 W, eight
loudspeakers (woofer and tweeter in
each door).
• Premium Sound:
AM/FM radio, CD player, 4x70 W +
25 W, Dolby Pro Logic II, 12 loudspeaker
(woofer, mid-range and tweeter in the
front doors, woofer and tweeter in the
rear doors, woofer and tweeter in the
centre dashboard speaker).
NUM
The exact specifications for these levels may
vary between markets. Certain levels are not
offered on all markets. The options list (subwoofer, CD/MD player, CD changer,
telephone, navigation, etc.) differs between
markets. Not all options are available for all
levels.
This owner’s manual describes one way of
operating the audio and telephone system. If
your car has a keypad in the steering wheel,
this can also be used.
Infotainment system
Control panel
Control panel on centre console
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Control panel on centre console
12.
13.
POWER – Audio On/Off
PHONE – Telephone On/Off/Standby
VOLUME – Volume control
CD/MD – Switches between CD and
MD (option)
AM/FM – Switches between FM1, FM2
and AM
MENU – Opens the main menu
ENTER – Selects menu options,
activates a selection or wakes the
telephone from standby.
EXIT – Goes back in the menu, cancels
a selection, puts the telephone into
standby, and erases the preceding
character when entering text and
numbers.
Navigation button – scrolls up/down in
the menus, scans/changes tracks/
stations, scroll forward/backward when
entering text and digits, and switches
between discs in the CD changer
TUNING – Scan/change tracks or
station
SOUND – Audio settings (e.g. bass,
treble and fader)
SCAN – Automatic station search
AUTO – Finds and stores the strongest
stations
14. Display – Displays options, menus and
information
15. Slot for inserting/ejecting
16. Eject – CD/MD
17. Station preset buttons/CD changer disc
(1-6), number/character buttons for the
telephone, and menu presets
Display
The display shows the function currently in
use, for example menu options, messages,
telephone numbers or settings. In daylight
the information is displayed against a light
background. In darkness it is displayed
against a dark background. Clean the display
with a soft, dry cloth. Never use cleaning
agent.
This display is also used for the climate
control system.
Menus
Press MENU to access the main menu. The
settings for the active audio system source
(radio for example) are selected from the
main menu. Audio settings cannot be made if
the audio system is not switched on.
Using the menu:
– Use the navigation button to scroll up and
down in the menu.
NUN
Infotainment system
Control panel
– Press EXIT to cancel, decline an option,
or go back one step in the menu
structure.
– Press ENTER to confirm, select or scroll
from one submenu to the next submenu.
If the battery voltage is low, a message
appears on the display. The energy saving
feature switches off certain functions or
reduces the load on the battery, such as by
lowering the volume of the sound system.
NUO
Infotainment system
Audio functions
Volume control
Turn the volume knob clockwise or anticlockwise to raise or lower the volume. The
volume can also be controlled using the
steering wheel keypad.
The car has a speed-dependent volume
feature known as active sound control ASC.
This adjusts the volume automatically
depending on the speed of the car.
Audio On/Off
The ignition switch must at least be in
position I. Press the POWER button to
switch the audio system on or off. If the audio
system is active when the ignition is switched
off, it will reactivate automatically when the
car is restarted.
Selecting the sound source
Select the sound source with the CD/MD
and AM/FM buttons.
• Press the AM/FM button repeatedly to
scroll between FM1, FM2 and AM.
The selected sound source is shown on the
display.
Pause mode
When the volume is turned to zero, the
CD/MD player switches to pause mode.
Reactivate the player by turning up the
volume.
Volume control for TP, PTY,
news and alarms
If a CD is playing when the radio receives a
traffic announcement, the CD player enters
pause mode. The announcement is played at
the volume selected for that type of message.
The system then returns to the volume
selected for the CD player. If the volume is
adjusted while the announcement is
broadcast, this new volume is saved and
used for the next bulletin.
Audio settings
– Press SOUND.
– Press the SOUND button repeatedly until
you reach the function you wish to set.
Choose between BASS, TREBLE,
FADER, BALANCE, SUBWOOFER
(option), CENTRE, and SURROUND.
– Use the TUNING knob to set the level.
The display shows a max-min scale. The
middle indicates the normal position.
Audio settings
Bass
Treble
Balance between
the front and rear
speakers
Balance between
the left and righthand speakers
Level for
subwoofer
Level for centre
loudspeaker
(certain models)
Level for surround
sound (certain
models)
Shown on the
display
BASS
TREBLE
FADER
BALANCE
SUBWOOFER
(option)
CENTRE
SURROUND
The level for the centre speaker can only be
set if Dolby Pro Logic II (DPL II ) or 3 channel
(3CH) has been selected from the menu. The
subwoofer level can only be set if the
subwoofer is activated.
NUP
Infotainment system
Audio functions
Dolby Surround Pro Logic II
(certain models)
Dolby Surround Pro Logic II, with its centre
loudspeaker in the dashboard, provides more
realistic sound reproduction.
The normal left and right stereo channels are
divided into left-centre-right. In addition,
ambient surround sound is produced through
the rear loudspeaker channels.
Dolby Surround Pro Logic II works in CD and
MD modes. 3 channel is recommended for
AM and FM radio broadcasts. Dolby
Surround Pro Logic II is only available for the
highest audio level, Premium Sound.
Setting the surround sound:
– Press MENU.
– Select the menu for the sound source and
press ENTER.
– Select AUDIO SETTINGS and press
ENTER.
– Select SURROUND AM/FM or
SURROUND CD/MD and press ENTER.
– Select Dolby Pro Logic II, 3 channel or
Off and press ENTER.
The symbol for Dolby Pro Logic II is shown on
the display if this has been selected.
3 channel is shown on the display if this has
been selected.
Off means the system is in normal stereo
mode.
NUQ
Dolby Surround Pro Logic II
and the Dolby icon are trademarks of Dolby Laboratories
Licensing Corporation. The
Dolby Pro Logic II Surround
System is manufactured under license from
Dolby Laboratories Licensing Corporation.
Subwoofer (option)
Gives the system a fuller sound and deeper
bass:
– Press MENU.
– Select the menu for the sound source and
press ENTER.
– Select SUBWOOFER and press ENTER.
A check in the box (on the display)
indicates that the subwoofer is activated.
Equalizer, front/rear
(certain models)
Fine adjustment of the sound from the front
speakers:
– Press MENU.
– Select the menu for the sound source and
press ENTER.
– Select AUDIO SETTINGS and press
ENTER.
– Select Equalizer front (rear) and press
ENTER.
– Use the navigation button or TUNING
knob to set the level.
– Use the navigation button to select the
next frequency. Five frequencies can be
adjusted.
– Press ENTER to save any changes and
exit.
– Press EXIT to exit without saving any
changes.
Infotainment system
Radio functions
slowly in the selected direction and
increases speed after a few seconds.
Release the button when the desired
frequency appears on the display.
If the frequency needs adjusting, touch one
of the arrows.
Storing stations
To store stations on the preset buttons 0-9:
Tuning
– Select radio mode AM, FM1 or FM2 using
the AM/FM button.
– Press the left or right arrow on the
navigation button to search for the next
strong station.
– Press one of the arrows again to initiate a
new search.
Manual tuning
There are two ways to tune into a station
manually.
• Turn the TUNING knob to set the desired
frequency.
• Press and hold the left or right arrow on
the navigation button. The frequency rolls
– Set the desired station.
– Press and hold the button you wish to
store the station on. The sound will be
muted for a couple of seconds and
Station stored appear on the display.
You can store up to 10 stations each for AM,
FM1 and FM2, i.e. a total of 30 stations.
Autostoring stations
Automatically tune and store up to ten AM or
FM stations in a separate memory. If more
than ten stations are found, the ten strongest
are selected. This function is particularly
useful if you are in an area in which you are
unfamiliar with the radio stations and their
frequencies.
– Select radio mode with the AM/FM
button.
– Start the search by pressing and holding
AUTO (more than 2 seconds).
– Autostoring appears on the display and a
number of strong stations (max. 10) from
the selected frequency band are stored in
the autostore memory. It there are no
stations that are sufficiently strong, No
station found appears on the display.
The stations are stored on buttons 0-9. When
the radio is in autostore mode, Auto is shown
on the display. The text disappears when you
return to the ordinary radio mode. Return to
the ordinary radio mode by pressing the AM/
FM button or EXIT, or by touching (less than
0.7 seconds) AUTO.
Returning to autostore mode:
– To access the most recently stored
stations, touch AUTO and then select a
station with buttons 0-9.
Scanning
Scanning for a station:
– Select radio mode with the AM/FM
button.
– Press SCAN. Scan appears on the
display.
– Press SCAN or EXIT to quit.
This function automatically searches for the
next strong AM or FM station signals. When
the radio finds a station, scanning pauses for
approximately 8 seconds, after which it
continues.
NUR
Infotainment system
Radio functions
Radio Data System — RDS
RDS is a system that links together specific
network transmitters. It is used, for example,
to tune the correct frequency of a station
irrespective of the transmitter or the active
audio source (e.g. CD). The system can also
be used for receiving traffic information and
for finding broadcasts of a specific type.
Radio text is also a component of RDS. A
radio station can transmit information about
the radio programme currently being
broadcast.
NOTE! Some radio stations do not use RDS
or only use a limited range of its features.
PI seek (automatic search for
transmitter)
PI seek appears on the display when
reception is poor for the selected station. The
radio automatically searches for the
strongest transmission for that station.
PI seek Exit to cancel is shown on the display
until the station is found.
News
Messages with a programme code (such as
news from RDS stations) will interrupt other
sound sources at the volume set for this
specific feature. As soon as the news
broadcast is finished, the audio system
NUS
returns to the previous sound source and
volume setting.
Activating News
– Select radio mode with the AM/FM
button.
– Press MENU.
– Select the menu for the sound source and
press ENTER.
– Select News and press ENTER.
NEWS appears on the display. Press EXIT if
you do not wish to listen to a news broadcast.
The News function remains active and the
radio waits for the next news programme.
Deactivating
– Select radio mode with the AM/FM
button.
– Press MENU.
– Select the menu for the sound source and
press ENTER.
– Select News and press ENTER.
Infotainment system
Interruptions for news from the
current station
– Select the radio with the AM/FM button.
– Activate the station broadcasting the
news items.
– Press MENU.
– Select Advanced audio settings and
press ENTER.
– Select News station and press ENTER.
– Select News from current station and
press ENTER.
Deactivating
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Advanced radio settings and press
ENTER.
– Select News and press ENTER.
– Select News station and press ENTER.
– Select News from all stations and press
ENTER.
Traffic information — TP station
Traffic information from RDS stations interrupts other sound sources. The message is
heard at the volume set for this specific
feature. As soon as the message ends, the
audio system returns to the previous sound
source and volume setting.
Activating traffic information
– Press MENU.
– Select the menu for the sound source.
– Select TP and press ENTER.
TP is shown on the display when the function
is activated. If the set station does not
broadcast traffic information TP))) appears
on the display. Press EXIT if you do not wish
to listen to the current traffic announcement.
The TP function remains active and the radio
waits for the next traffic announcement.
Activating traffic information from a
specific station
– Select radio mode with the AM/FM
button.
– Activate the station from which traffic
information is to be received.
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Advanced radio settings and press
ENTER.
– Select TP and press ENTER.
– Select TP Station and press ENTER.
– Select TP from current station.
Deactivating TP station
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Advanced radio settings and press
ENTER.
– Select TP and press ENTER.
– Select TP Station and press ENTER.
– Select TP from all stations and press
ENTER.
TP search
This function allows you to listen to traffic
information when travelling between different
areas and countries without selecting a
station.
– Press MENU.
– Select a sound source.
– Select Advanced radio settings and press
ENTER.
– Select TP and press ENTER.
– Select TP search and press ENTER.
Deactivating
Select TP search again and press ENTER.
Radio text
Some RDS stations broadcast information,
such as about programme content and
artists.
Displaying text information on the
display
– Press MENU. Select the menu for the
sound source and press ENTER (the
current sound source is always
highlighted when you access the menu if
the audio system is on).
– Select Radio text on the menu and press
ENTER.
Deactivating
Select Radio text again and press ENTER.
NUT
Infotainment system
Radio functions
Alarm
Alarms are transmitted automatically. The
function cannot be deactivated. ALARM! is
shown on the radio display when an alarm
message is broadcast. The function is used
to warn motorists of serious accidents or
disasters.
Programme type — PTY
Use the PTY function to select between the
various programme types.
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select PTY and press ENTER.
– Select Show PTY and press ENTER. The
set station’s programme PTY will be
shown on the display.
NOTE! Not all radio stations have a PTY
designation.
Programme type — shown on display
• Current affairs
• Information
• Sport
• Education
• Drama
• Cultures
• Science
• Varied speech
• Pop music
NUU
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Rock music
Easy listening
Light classic
Serious classic
Other music
Weather & Metro
Finance
Children’s progs
Social affairs
Religion
Phone In
Travel & Touring
Leisure & Hobby
Jazz music
Country music
National music
Oldies music
Folk music
Documentary
Searching for a specific
programme type
Search through the entire frequency band:
– Select FM 1 or FM 2 and press MENU.
– Select the menu for the sound source and
press ENTER.
– Select PTY and press ENTER.
– Scroll to Select PTY and press ENTER.
– Press ENTER for one or more of the listed
programme types. The PTY symbol on the
display lights up when the first selection
is made and the radio is set to standby
for PTY.
– Press EXIT to go back.
– Select Search PTY and press ENTER. If
the radio finds a station with the selected
programme type, this is played.
If the radio does not find a station with the
selected programme type, it returns to the
previous frequency.
PTY mode is then in standby until the
selected programme type is broadcast.
When this happens, the radio automatically
switches to the station broadcasting the
selected programme type.
Deactivating
– Select Clear all PTY. The PTY symbol
disappears from the display and the radio
returns to normal mode.
PTY standby
To set the radio to PTY standby, perform
steps 1-6.
Automatic frequency updating
The AF function is normally activated and
ensures that the radio tunes to the strongest
available transmitter.
Infotainment system
Automatic frequency updating
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Advanced radio settings and press
ENTER.
– Select AF and press ENTER.
Reactivating
– Select AF and press ENTER.
Regional radio programmes
The regional function is normally deactivated.
When the function is activated you can
continue to listen to a regional broadcasts
even if the signal is weak.
Activating regional radio programmes
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Advanced radio settings and press
ENTER.
– Select Regional and press ENTER.
– REG is shown on the display.
Deactivating
– Select REG again and press ENTER.
EON - Local/Distant/Off
(Enhanced Other Networks)
The function has three levels:
• Local - Only interrupts if the signal is
strong.
• Distant - Interrupts even if the signal is
weak.
• Off - Deactivated.
Activating EON
– Press MENU.
– Select the menu for the sound source and
press ENTER.
– Select Advanced radio settings and press
ENTER.
– Select EON and press ENTER.
– Select Local, Distant or Off and press
ENTER.
Resetting RDS functions
Resets all radio settings to the original factory
settings.
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Advanced radio settings and press
ENTER.
– Select Reset all and press ENTER.
– Press ENTER again to confirm.
With EON activated, traffic announcements
and news broadcasts interrupt radio
programmes.
NUV
Infotainment system
CD/MD (option)
Important!
Use only standard 12 cm CDs, no mini
CDs. Do not use CDs with adhesive disc
labels. The heat from the CD player may
cause the label to detach from the disc.
This could damage the CD player.
Fast forward/reverse
Press and hold the left or right arrow on the
navigation button to search within a track or
the whole disc. Searching continues for as
long as the button is depressed.
Starting the CD/MD player
(option)
Activate the CD/MD player by pressing the
CD/MD button. Insert a disc into the player.
CDs
If the quality of the CD does not comply with
the requirements of standard EN60908 or if
it has been recorded using poor equipment,
sound quality may be poor or playback interrupted.
Changing tracks
Press the left or right arrow on the navigation
button to skip to the previous or next track.
The track number is shown on the display.
You can also use the TUNING knob (or
steering wheel keypad).
NVM
Random
This function chooses a CD track in no particular order.
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Random and press ENTER.
RND is shown on the display as long as the
function is activated.
Deactivating
– Select Random again and press ENTER,
or press EXIT.
Scan
Scan plays the first ten seconds of each
track.
– Press SCAN.
– Press EXIT to play the current track.
Disc text
Some CDs have title information. The information is displayed as text on the display
(only applies to the combined CD/MD
player).
Activating Disc text
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Disc text and press ENTER.
If information is stored on the disc, this is
shown on the display.
Deactivating
– Select Disc text and press ENTER.
Infotainment system
Ejecting a CD/MD
Press the eject button to eject the disc. For
traffic safety reasons, a CD remains ejected
for only 12 seconds. The player will then feed
the disc back into the player and switch to
pause mode (N/A MD). Press CD/MD to
reactivate the player.
NVN
Infotainment system
CD changer (option)
CDs
Fast forward/reverse
If the quality of the CD does not comply with
the requirements of standard EN60908 or if
it has been recorded using poor equipment,
sound quality may be poor or playback interrupted.
Press and hold the left or right arrow on the
navigation button to search within a track or
the whole disc. Searching continues for as
long as the button is depressed.
Important!
Use only standard 12 cm CDs, no mini
CDs. Do not use CDs with adhesive disc
labels. The heat from the CD player may
cause the label to detach from the disc.
This could damage the CD player.
Starting the CD changer
The CD changer can hold up to six discs.
Starting the CD changer:
– Press the CD button.
– Select an empty slot using the
buttons 1-6 (or up/down navigation
button). The display shows which slots
are empty.
– Insert a CD into the CD changer.
Make sure Insert disc is displayed before you
insert the disc
NVO
Selecting discs
Select the disc you wish to play using the
buttons 1-6 or by pressing the up or down
arrow on the navigation button. The number
of the disc and track are shown on the
display.
Changing tracks
Press the left or right arrow on the navigation
button to skip to the previous or next track.
The track number is shown on the display.
You can also use the TUNING knob (or
steering wheel keypad).
Random
Plays tracks from a CD or CDs in random
order.
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Random and press ENTER.
– Select Single disc or All discs to play
tracks from a single disc or all discs in the
CD changer in random order.
– RND or RND ALL is shown on the display
while the function is active.
– Press the right arrow on the navigation
button to select the next random track.
Deactivating
– Press EXIT.
NOTE! You can only select the next random
track on the current disc.
Scan
Scan plays the first ten seconds of each track.
– Press SCAN.
NOTE! Press EXIT to play the current track.
Infotainment system
Disc text
Some CDs have title information. The information is displayed as text on the display.
Activating disc text
– Press MENU. Select the menu for the
sound source and press ENTER.
– Select Disc text and press ENTER.
If information is stored on the disc, this is
shown on the display.
Deactivating
– Select Disc text and press ENTER.
Ejecting single disc
Press the eject button. The CD remains
ejected for only 12 seconds. The changer will
then feed the disc back in and switch to
pause mode. Press CD/MD to reactivate the
player.
Ejecting all discs
Press and hold the eject button (for longer
than 2 seconds) to initiate the eject function.
The entire magazine is emptied, disc by disc.
Eject all is shown on the display.
NVP
Infotainment system
Menu settings and options — Audio
FM1/FM2 menu
1
1. News Off/
2. TP On/Off1
3. PTY
3.1.
Select PTY
3.1.1.
CLEAR ALL PTY
3.1.2.
List of PTY
3.2.
Search PTY
3.3.
Show PTY On/Off
4. Radio text On/Off1
5. Advanced radio settings
5.1.
TP
5.1.1.
TP station
5.1.2.
TP search On/Off1
5.2.
News station
5.3.
AF On1/Off
5.4.
Regional On/Off1
5.5.
EON
5.5.1.
Off
5.5.2.
Local
5.5.3.
Distant1
5.6.
Reset all
6. Audio settings
6.1.
Surround AM/FM (certain models)
6.1.1.
Dolby Pro Logic II
6.1.2.
3 channel
6.1.3.
Off1
NVQ
6.2.
Surround CD/MD (certain models)
6.2.1.
Dolby Pro Logic II
6.2.2.
3 channel
6.2.3.
Off
6.3.
Subwoofer On1/Off (option)
6.4.
Equalizer front (certain models)
6.5.
Equalizer rear (certain models)
6.6.
Automatic volume control
6.6.1.
Low
6.6.2.
Medium
6.6.3.
High
6.7.
Reset all
AM menu
7. Audio settings
7.1.
Surround AM/FM (certain models)
7.1.1.
Dolby Pro Logic II
7.1.2.
3 channel Off1
7.2.
Surround CD/MD (certain models)
7.2.1.
Dolby Pro Logic II
7.2.2.
3 channel
7.2.3.
Off
7.3.
Subwoofer On1/Off (option)
7.4.
Equalizer front (certain models)
7.5.
Equalizer rear (certain models)
7.6.
Automatic volume control
7.6.1.
Low
7.6.2.
Medium
7.6.3.
High
7.7.
Reset all
CD menu
1. Random
2. News (Off1)
3. TP (Off1)
4. Audio settings
4.1.
Surround AM/FM (certain models)
4.1.1.
Dolby Pro Logic II
4.1.2.
3 channel
4.1.3.
Off1
4.2.
Surround CD/MD (certain models)
4.2.1.
Dolby Pro Logic II
4.2.2.
3 channel
4.2.3.
Off
4.3.
Subwoofer (On1) (option)
4.4.
Equalizer front (certain models)
4.5.
Equalizer rear (certain models)
4.6.
Automatic volume control
4.6.1.
Low
4.6.2.
Medium
4.6.3.
High
4.7.
Reset all
Infotainment system
CD changer menu
CD/MD menu
1. Random
1.1.
Off1
1.2.
Single disc
1.3.
All discs
2. News (Off1)
3. TP (Off1)
4. Disc text (Off1)
5. Audio settings
5.1.
Surround AM/FM (certain models)
5.1.1.
Dolby Pro Logic II
5.1.2.
3 channel
5.1.3.
Off1
5.2.
Surround CD/MD (certain models)
5.2.1.
Dolby Pro Logic II1
5.2.2.
3 channel
5.2.3.
Off
5.3.
Subwoofer (On1) (option)
5.4.
Equalizer front (certain models)
5.5.
Equalizer rear (certain models)
5.6.
Automatic volume control
5.6.1.
Low
5.6.2.
Medium
5.6.3.
High
5.7.
Reset all
1. Random
2. News (Off1)
3. TP (Off1)
4. Disc text (Off1)
5. Audio settings
5.1.
Surround AM/FM (certain models)
5.1.1.
Dolby Pro Logic II
5.1.2.
3 channel
5.1.3.
Off1
5.2.
Surround CD/MD (accessory)
5.2.1.
Dolby Pro Logic II1
5.2.2.
3 channel
5.2.3.
Off
5.3.
Subwoofer (On1) (option)
5.4.
Equalizer front (option)
5.5.
Equalizer rear (option)
5.6.
Automatic volume control
5.6.1.
Low
5.6.2.
Medium
5.6.3.
High
5.7.
Reset all
1.
Default/Factory setting
NVR
Infotainment system
Telephone (option)
Telephone system components
NVS
Infotainment system
1. Antenna
The antenna is mounted on the roof.
2. Steering wheel keypad
The majority of the telephone functions can
be controlled using the keypad. When the
telephone is active, the keypad can only be
used for telephone functions. Telephone
information is always displayed on the control
panel when the telephone is activated.
• Switch off the system near blasting work.
• Let only authorised personnel service the
telephone system.
Emergency calls
Emergency calls to alarm centres can be
made without a SIM card as long as there is
coverage by a GSM operator.
The hands free microphone is integrated in
the roof console beside the rearview mirror.
Making an emergency call:
– Activate the telephone.
– Ring the emergency number that applies
to your region (within EU: 112).
– Press ENTER.
4. Control panel
Loudspeaker
All functions (except call volume) can be
controlled using the keypad in the control
panel. The display shows menu functions,
messages, telephone numbers, etc.
The telephone uses the loudspeaker in the
driver’s door or the audio system’s centre
speaker (if there is one).
3. Microphone
5. Privacy handset (option)
6. SIM card
The SIM card is located in a holder in the
glovebox.
General
• Always put traffic safety first.
• If the driver needs to use the privacy
handset, park the car in a safe place first.
• Switch off the telephone system when
refuelling the car.
NVT
Infotainment system
Telephone functions
Double SIM cards
IMEI number
Many network operators offer double SIM
cards - one for your car and one for another
telephone. A double SIM card allows you to
have the same number for two different telephones. Ask your network operator about the
offers available and the use of double SIM
cards.
To block the telephone, you must provide
your network operator with the telephone’s
IMEI number. This is a 15 digit serial number
that is programmed in the phone. To display
this number, dial *#06#. Make a note of this
number and keep it in a safe place.
Specifications
SIM card
The telephone can only be used with a valid
SIM card (Subscriber Identity Module). The
card is provided by your network operator.
Contact your network operator if you
experience difficulties with the SIM card.
Insert the SIM card to start using the
telephone.
– Switch off the telephone.
– Open the glovebox and the cover for the
SIM card holder.
– Pull out the SIM card holder.
– Place the card metal side up. Ensure that
the bevelled corner of the SIM card
matches the bevel of the holder.
– Carefully press the holder back in.
NVU
Output
2W
SIM card
Small
Memory entries
2551
SMS (Short Message
Service)
Yes
Data/Fax
No
Dualband
Yes (900/
1800)
1. The capacity of the SIM card’s memory
varies depending on the subscription.
Infotainment system
1.
2.
3.
4.
5.
6.
7.
8.
PHONE – On/Off/Standby.
MENU – Opens the main menu.
ENTER – Accept a call, select in the
menu or activate the telephone from
standby. Press ENTER once to display
the last dialled number.
EXIT – Terminate/reject a call, scroll
back in the menu, cancel a selection or
erase entered digits/characters.
Navigation button – Scroll up or down in
the menus, scroll forwards or back when
entering text and digits.
Display.
Number/character keys and menu
option shortcuts.
VOLUME – Controls the background
volume from the radio, for example,
during a call.
Steering wheel keypad
1.
2.
3.
4.
ENTER – Accept a call, scroll the menu
or activate the telephone from standby.
Press ENTER once to display the last
dialled number.
EXIT – Terminate/reject a call, scroll
back in the menu, cancel a selection or
erase entered digits/characters.
Volume – Increase/decrease call volume
during a call.
Navigation button – Scroll up/down in
menus, scroll forward/back when
entering text and digits.
Control panel on centre console
NVV
Infotainment system
Telephone functions
Switch
When the telephone system is active or in
standby mode, a handset is shown on the
display. If the car’s ignition is switched off
while the telephone system is on, the system
will be on the next time the ignition is
switched on. No calls can be received while
the telephone system is switched off.
Activating the telephone system
– Press PHONE.
– Enter the PIN code and press ENTER.
Switching off
– Press and hold the PHONE button to
switch off the telephone system.
Standby
– Press PHONE or EXIT to out the
telephone system into standby.
Reactivating
– The system can be reactivated by
touching the PHONE button.
Making and receiving calls
To call:
– Dial the number and press ENTER on the
steering wheel keypad or on the control
panel, or lift the handset.
Receiving a call:
OMM
– Press ENTER or lift the handset. You can
also use Automatic Answer. See menu
option 4.3.
The car’s audio system can be muted
automatically while a telephone conversation
is in progress. See menu option 5.5.3.
Volume reduction during
telephone call
If the telephone rings when the radio is
switched on, the volume is lowered when the
call is answered. When the call is concluded,
the volume returns to the previously set level.
It is possible to adjust the radio volume when
the telephone is in use and this new volume
kept after the call is ended. The audio system
can also be muted during a telephone call.
See menu 5.5.3. This function only applies to
the Volvo integrated telephone system.
Ending a call
Press EXIT or hang up the handset. The
audio system resumes its previous activity.
Reject an incoming call by pressing EXIT.
Standby
Calls can be received while the audio system
is active and information from an audio
system source is shown on the display. The
telephone must be in active mode to use the
other functions of the telephone system.
Menu shortcuts
In the menu system, you can use numbers
instead of the arrows and ENTER to select a
menu at the main menu level. Each menu
selection is numbered. The numbers are
shown on the display together with the menu
option.
Traffic safety
For safety reasons, parts of the menu system
cannot be accessed at speeds in excess of
8 km/h. Only activities started in the menu
system can be completed. The speed limiter
can be deactivated using menu
function 5.6.1 Menu lock.
IDIS
(Intelligent Driver Information System) The
IDIS system allows incoming telephone calls
and text (SMS) messages to be delayed so
that the driver can concentrate on driving.
Incoming calls and text messages can be
delayed by 5 seconds before they are
connected. Missed calls are shown on the
display. IDIS can be deactivated using menu
function 5.6.2.
Infotainment system
Press ENTER and return the handset to
its cradle. If the handset is already
removed from its cradle at the start of a
call, the other party will be audible via the
handsfree system. Press the MENU
button, scroll to Handset and press
ENTER in order to transfer to the handset.
Last dialled number
The telephone automatically stores the last
telephone numbers/names called.
Calling the last dialled number:
Privacy handset (option)
Making a call using the handset:
– Dial the number using the keypad on the
centre console and lift the handset to
make the call. Press the handset down
before lifting it.
The call is ended when the handset is hung
back in its cradle.
Adjust the handset volume using the dial on
the side of the handset.
To switch to handsfree without ending the
call:
– Press the right arrow on the steering
wheel keypad (or the menu button on the
control panel) and select Handsfree.
– Press ENTER on the steering wheel
keypad or control panel (when in active
mode).
– Use the navigation buttons to scroll
forward or back through the last numbers
dialled. These are shown on the display.
– Press ENTER.
Speed dial
A number stored in the phone book can be
linked to a speed dial button (1-9).
– Select Phone book on the menu and
press ENTER.
– Scroll to Speed dial, menu 3.4, and press
ENTER.
– Select which number is to be the speed
dial number. Press ENTER to confirm.
– Search for the desired name or phone
number in the phone book. Press ENTER
to select.
– To make a call, press and hold the
desired speed dial button for two
seconds or press the button briefly and
then press ENTER.
NOTE! When the telephone is switched on, it
takes a while before speed dialling is
available. Menu option 3.4.1 must be
activated to use the speed dial function.
Call waiting
A two-tone signal during a telephone call
indicates that there is another incoming call.
The display shows: Answer?
Receiving a call:
– Press ENTER. Your current call will be
put on hold.
– Select Hold/Resume to finish the call and
return to a call on hold.
To reject the incoming call: Press EXIT.
To end the current call: Press EXIT. The
function can be de-selected in the menu.
Functions during a call
Several functions are available during a call.
OMN
Infotainment system
Telephone functions
Scroll with the navigation button and press
ENTER to make a selection.
Secret mode/
Secret mode off
Secret mode
Hold/Resume
Choose whether the
call is to be put on
hold or resumed
Handsfree/
headset
Use the handsfree
function or headset
Phone book
Show phone book
Several functions are available during a call
while another call is on hold.
Scroll with the navigation button and press
ENTER to make a selection.
Secret mode/
Secret mode off
Secret mode
Handsfree/
headset
Use the handsfree
function or headset
Three-way
calling
Conference call
(further options)
Switch
Switch between two
calls
Phone book
Show phone book
OMO
Call volume
Control the call volume during the call by
pressing the buttons with the large and small
loudspeakers on the steering wheel keypad.
When the telephone is activated, the steering
wheel keypad only controls the telephone
functions.
The telephone must be in standby mode to
control the audio system using the steering
wheel keypad.
Phone book
Telephone numbers and names can be
stored in either the telephone memory or the
SIM card memory.
If the number of the person calling is stored in
the phone book, the name of the caller will be
shown on the display.
The telephone memory can store up to 255
names.
Storing a telephone numbers and name:
–
–
–
–
–
–
Press MENU.
Select Phone book and press ENTER.
Scroll to Enter item and press ENTER.
Enter a name and press ENTER.
Enter a number and press ENTER.
Select the memory in which the entry is to
be saved an d press ENTER.
Copying entries between the SIM card
and Phone book
Copying from the SIM card to the phone
book:
–
–
–
–
Press MENU.
Select Phone book.
Select Copy all.
Select From SIM card to phone book and
press ENTER.
You can also copy entries from the phone
book to the SIM card.
Erasing names
Erasing from the phone book:
–
–
–
–
Press MENU.
Select Phone book.
Select Search.
Enter the first letter of the name (or the
entire name) and press ENTER.
– Scroll to the name you wish to delete and
press ENTER.
– Select Erase to delete the entry.
Entering a name/message
Press the button with the relevant character.
Press once for the first character, twice for
the second character and so on. Press 1 for
space.
Infotainment system
1
2
3
4
5
6
7
8
9
*
0
#
EXIT
space 1- ? ! , . : " ' ( )
abc2äåàæç
def3èé
ghi4ì
jkl5
mno6ñöòØ
pqrs7ß
tuv8üù
wxyz9
if you enter two letters in a row
from the same button, press *
between them or wait a few
seconds.
[email protected]*#&$£/%
switch between upper and lower
case
Erase the last entered character. If
you press and hold this, the entire
number or text is deleted.
Calling from the memory
– Press MENU.
– Scroll downward using the navigation
button (or the left arrow button on the
steering wheel to search the phone
book).
– Press ENTER. Scroll to the desired name
using the navigation button or press the
first letter of the name (or enter the entire
name). Press ENTER.
– Press ENTER to dial the selected
number.
Quitting text input:
– Erase all entered characters with by
pressing and holding EXIT.
– Return to the menu by again pressing and
holding EXIT.
OMP
Infotainment system
Menu settings and options — Telephone
Telephone menu
1. Call log
1.1.
Missed calls
1.2.
Received calls
1.3.
Outgoing calls
1.4.
Erase list
1.4.1.
All calls
1.4.2.
Missed calls
1.4.3.
Received calls
1.4.4.
Outgoing calls
1.5.
Call duration
1.5.1.
Last call
1.5.2.
Number of calls
1.5.3.
Total time
1.5.4.
Reset time
2. Messages
2.1.
Read
2.2.
Write
2.3.
Message settings
2.3.1.
SMSC number
2.3.2.
Validity period
2.3.3.
Message type
3. Phone book
3.1.
Enter item
3.2.
Search
3.3.
Copy all
3.3.1.
SIM to telephone
3.3.2.
Telephone to SIM
OMQ
3.4.
Speed dial
3.4.1.
Active
3.4.2.
Select number
3.5.
Empty SIM
3.6.
Empty telephone
3.7.
Memory status
4. Call options
4.1.
Transmit number
4.2.
Call waiting
4.3.
Automatic answer
4.4.
Automatic redial
4.5.
Call divert
4.5.1.
All calls
4.5.2.
When busy
4.5.3.
When not answered
4.5.4.
If unreachable
4.5.5.
Fax calls
4.5.6.
Data calls
4.5.7.
Cancel all diverts
5. Tel. settings
5.1.
Network selection
5.1.1.
Automatic
5.1.2.
Manual
5.2.
Language
5.2.1.
English UK
5.2.2.
English US
5.2.3.
Español
5.2.4.
Français CAN
5.2.5.
Français FR
5.2.6.
Italiano
5.2.7.
Nederlands
5.2.8.
Português BR
5.2.9.
Português P
5.2.10. Suomi
5.2.11. Svenska
5.2.12. Dansk
5.2.13. Deutsch
5.3.
SIM security
5.3.1.
On
5.3.2.
Off
5.3.3.
Automatic
5.4.
Change codes
5.4.1.
PIN code
5.4.2.
Telephone code
5.5.
Volume
5.5.1.
Ringer volume
5.5.2.
Ringer tone
5.5.3.
Mute radio
5.5.4.
Message beep
5.6.
Traffic safety
5.6.1.
Menu lock
5.6.2.
IDIS
5.7. Factory settings
Infotainment system
Menu options, description
1. Call log
1.1. Missed calls
List of missed calls. You can choose to call,
erase or store the number in the phone book.
1.2. Received calls
List of received calls. You can choose to call,
erase or store the number in the phone book.
1.3. Outgoing calls
List of dialled numbers. You can choose to
call, erase or store the number in the phone
book.
1.4. Erase list
Erase the lists found in the menus 1.1, 1.2
and 1.3 as below.
1.4.1.
All
1.4.2.
Missed
1.4.3.
Received
1.4.4.
Outgoing
1.5. Call duration
Call duration of all calls or of the latest call.
1.5.1.
Last call
1.5.2.
Number of calls
1.5.3.
Total time
1.5.4.
Reset time
The telephone code is required to reset the
call timer (see Menu 5.4).
2. Messages
2.1. Read
Received text messages. Select whether to
erase, forward, change or save the entire
message or parts of it.
2.2. Write
Write a message using the keypad. Choose
whether to save or send it.
3.3. Copy all
Copy telephone numbers and names from
the SIM card to the telephone memory.
3.3.1.
From SIM to telephone memory
3.3.2.
From telephone to SIM memory
3.4. Speed dial
A number stored in the phone book can be
stored as a speed dial number.
2.3. Message settings
Enter the number (SMSC number) of the
message centre to which you want your
messages transferred as well as how long
they are to be saved at the message centre.
3.5. Empty SIM
Select to erase the entire memory of the SIM
card.
2.3.1.
SMSC number
2.3.2.
Validity period
2.3.3.
Message type
Contact your network operator for information about these settings and for an
SMSC number. Normally, these settings
should not be altered.
3.7. Memory status
Shows how many entries are occupied by
names and numbers in the SIM card and
telephone memory. The table shows how
many spaces are occupied of the total,
e.g. 100(250).
3. Phone book
3.1. Enter item
Store names and numbers in the phone book.
See the section on phone book functions for
more information.
4. Call options
4.1. Transmit number
Select whether or not your own number
should be displayed to the person you call.
Contact your network operator regarding exdirectory numbers.
3.6. Empty memory
Erase the entire telephone memory.
3.2. Search
Search for a name in the phone book.
OMR
Infotainment system
Menu settings and options — Telephone
4.2. Call waiting
Select whether or not you want to be alerted
during a phone call that there is another
incoming call.
4.3. Automatic answer
Automatically answers incoming calls.
4.4. Call back
Calls a previously engaged number.
4.5. Call divert service
Choose when and what type of calls are to be
diverted to a specified telephone number.
4.5.1.
4.5.2.
4.5.3.
4.5.4.
4.5.5.
4.5.6.
4.5.7.
All calls (this setting only applies
during the call in progress)
When busy
When not answered
If unreachable
Fax calls
Data calls
Cancel all diverts
5. Telephone settings
5.1. Network selection
Choose a network automatically or manually.
The selected operator is shown in the display
in the telephone’s basic mode.
5.1.1.
AUTO
5.1.2.
Manual
5.2. Language
Select the telephone language.
OMS
5.2.1.
English UK
5.2.2.
English US
5.2.3.
Español
5.2.4.
Français CAN
5.2.5.
Français FR
5.2.6.
Italiano
5.2.7.
Nederlands
5.2.8.
Português BR
5.2.9.
Português P
5.2.10. Suomi
5.2.11. Svenska
5.2.12. Dansk
5.2.13. Deutsch
5.3. SIM security
Select if the PIN code should be on, off or if
the telephone should automatically give the
PIN code.
5.3.1.
On
5.3.2.
Off
5.3.3.
Automatic
5.4. Change codes
Change the PIN code or telephone
code 5.4.1 PIN code 5.4.2.Telephone code
(use 1234 until you change to your own
code). The telephone code is used to reset
the call timer. Make a note of your code and
save it in a safe place.
5.5. Volume
5.5.1.
Volume. Adjust the ring tone
volume.
5.5.2.
Ring tone. There are seven different
ring tones.
5.5.3.
Mute radio: On/Off
5.5.4.
Message beep
5.6. Traffic safety
Disengage the speed function, i.e. make all
menu options accessible while driving.
5.6.1.
Menu lock
5.6.2.
IDIS
The IDIS function can be deactivated.
Incoming calls will not be delayed,
irrespective of whether the car is being driven
or not.
5.7. Factory settings
Reset the system’s factory settings.
Technical data
Type designations
Dimensions and weights
Engine specifications
Capacities
Fuel
Catalytic converter
Electrical system
208
209
210
212
215
217
218
OMT
Technical data
Type designations
Whenever contacting your Volvo dealer and
when ordering spare parts and accessories
for your car, it makes things easier if you
know your car’s type designation, vehicle
identification number and engine number.
1.
Type designation, VIN, maximum
permitted loads, code number for
colour and trim, and type approval
number (on right-hand B-pillar).
2. Engine type designation, component
and serial number (on the right-hand
side of the engine).
3. VIN (Type and model year designations and chassis number) stamped in
the engine compartment underneath
the windscreen.
4. Gearbox type designation and serial
number
(a) manual gearbox (on front side)
(b), (c) automatic gearbox (on the top).
OMU
Technical data
Dimensions and weights
Dimensions
Trailer with brakes
Length: 447 cm
Maximum trailer
weight
Width: 177 cm
Wheelbase: 264 cm
1.6 1200 kg
1.6D manual 1300 kg
1.8 1300 kg
others 1500 kg
Front track: 154-155 cm
Rear track: 153-154 cm
Weights
The kerb weight includes the driver, the fuel
tank 90 % full and all fluids. The weight of
passengers and accessories, such as a
towbar, towball load (when a trailer is
hitched, see table), load carriers, and roof box
etc. influence the payload and must not be
included in the kerb weight. Permitted weight
(in addition to driver) = Gross vehicle
weight–Kerb weight.
Maximum
towball load:
75 kg
Trailer without brakes
Maximum trailer
weight
For the location of the label, see page 208.
1. Max. total weight
2. Max. train weight (car+trailer)
3. Max. front axle load
4. Max. rear axle load
Maximum load: See registration document.
Maximum roof load: 75 kg
700 kg
Maximum
towball load:
50 kg
WARNING!
The car’s driving characteristics change
depending on how heavily it is loaded and
how the load is distributed.
OMV
Technical data
Engine specifications
1.6
Engine designation
Output (kW/rps)
(hp/rpm)
Torque (Nm/rps)
(kpm/rpm)
No. of cylinders
Bore (mm)
Stroke (mm)
Swept volume (dm3 or litres)
Compression ratio
Spark plugs:
Electrode gap (mm)
Tightening torque (Nm)
2.4
2.4i
B4184S11
92/100
125/6000
165/67
16.8/4000
4
83
83.1
1.80
B5244S5
103/83
140/5000
220/67
22.4/4000
5
83
90
2.44
B5244S4
125/100
170/6000
230/73
23.4/4400
5
83
90
2.44
11.0:1
10.8:1
10.3:1
10.3:1
1.2
15 ±2
1.3
12
3x0.6 +/-0.1
30
3x0.6 +/-0.1
30
Engine type designation, component and
serial number can be read on the engine, see
page 208.
ONM
1.8
B4164S3
74/100
100/6000
150/67
15.3/4000
4
79
81,4
1.60
Technical data
T5
Engine designation
Output (kW/rps)
(hp/rpm)
Torque (Nm/rps)
(kpm/rpm)
No. of cylinders
Bore (mm)
Stroke (mm)
Swept volume (dm3 or litres)
Compression ratio
Spark plugs:
Electrode gap (mm)
Tightening torque (Nm)
1.6D
2.0D
2.0D
B5254T3
162/83
220/5000
320/25-80
32.6/1500-4800
5
83
93.2
2.52
D4164T
81/67
110/4000
240/
24.5/
4
75
88.3
1.56
D4204T
100/67
136/4000
320/33
32.6/2000
4
85
88
2.00
D4204T21
98/67
133/4000
320/33
32.6/2000
4
85
88
2.00
9.0:1
18.3:1
18.5:1
18.5:1
0.7 +0.1
30
-
-
-
1. France
ONN
Technical data
Capacities
Engine oil
Engine variant
Volume between
MIN – MAX
Volume1
litres
4.0
Recommended oil grade:2
1.6
B4164S3
0-0.75
1.8
B4184S11
0-0.75
4.3
2.4
B5244S5
0-1.6
5.8
ACEA A1/B1
2.4i
B5244S4
T5
B5254T3
WSS-M2C913-B
1.6D
D4164T
0-1.0
3.7
2.0D
D4204T
0-2.0
5.5
2.0D
D4204T2
WSS-M2C913-B
1. Including filter change.
2. Alternative ACEA A5/B5.
3. The oil grade requirement must be fulfilled even if a different viscosity is chosen according to the diagram.
Extreme driving conditions
Check the oil more often in extreme driving
conditions such as alpine driving with a great
deal of engine braking or motorway driving at
high speed. These conditions may cause
abnormally high oil temperatures and oil
consumption.
Petrol engines: For extreme conditions,
choose a fully synthetic engine oil to provide
extra protection.
Volvo recommends Castrol® oil products.
ONO
Important!
Always use oil of the recommended
grade and correct viscosity.
Do not use oil additives. These can
damage the engine.
If the system is topped up with a different
oil, contact the nearest authorised Volvo
workshop for servicing.
Viscosity3
SAE 5W-30
Technical data
Other fluids and lubricants
Important!
The recommended transmission fluid must be used to prevent damage to the gearbox. Do not mix with any other transmission fluid. If the
transmission is topped up with a different fluid, contact an authorised Volvo workshop for servicing.
Fluid
Gearbox oil
Coolant
Engine variant/number of components
1.6 Manual 5 speed
1.8 Manual 5 speed
1,6D Manual 5 speed
2.0D Manual 6 speed
2.4 Manual 5 speed
2.4i Manual 5 speed
T5 Manual 6 speed
T5 Automatic gearbox
5 cyl. Petrol, manual gearbox
5 cyl. Petrol, automatic gearbox
4 cyl. Petrol (1.8)
4 cyl. Diesel (2.0D)
4 cyl. Petrol (1.6)
4 cyl. Diesel (1.6D)
Air conditioning1
Brake fluid
Power steering
System
of which reservoir
Volume
2.1 litres
1.9 litres
1.9 litres
1.7 litres
2.1 litres
2.1 litres
2.0 litres
7.75 litres
8.0 litres
8.5 litres
7.5 litres
9.5 litres
6.2 litres
7.2 litres
180-200 grams
500-600 grams
0.6 litres
1.2 litres
0.2 litres
Recommended oil grade
Transmission fluid: WSD-M2C200-C
Transmission fluid: MTF 97309-10
Transmission fluid: JWS 3309
Coolant with corrosion inhibitor mixed with
water, see packaging. The thermostat starts
opening at:
90 ºC in petrol engines and at 82 ºC in
diesel engines.
petrol engine (1.6) 82 ºC
diesel engine (1.6D) 83 ºC
Compressor oil PAG
Refrigerant R134a (HFC134a)
DOT 4+
Power steering fluid: WSS M2C204-A or
equivalent product with same specifications.
ONP
Technical data
Capacities
Fluid
Washer fluid
Fuel tank
Engine variant/number of components
4 cyl. Petrol/Diesel
5 cyl. Petrol
Volume
4.0 litres
6.5 litres
Recommended oil grade
Use a washer antifreeze recommended by
Volvo mixed with water at temperatures
below freezing.
See page 215
1. Weights can vary depending on the engine variant. Contact an authorised Volvo workshop for the exact information.
ONQ
Technical data
Fuel
Consumption, emissions and volume
Engine
Gearbox
1.6
1.8
2.4
B4164S3
B4184S11
B5244S5
2.4i
B5244S4
T5
B5254T3
Manual 5 speed (IB5)
Manual 5 speed (MTX75)
Manual 5 speed (M56)
Automatic gearbox (AW55-50/51)
Manual 5 speed (M56)
Automatic gearbox (AW55-50/51)
Manual 6 speed (M66)
Automatic gearbox (AW55-50/51)
Manual 6 speed (M66)
Automatic gearbox (AW55-50/51)
Manual 5 speed (MTX75)
Manual 6 speed (MMT6)
T5
AWD
1.6D
2.0D
2.0D
D4164T (EURO3)
(EURO4)
D4204T (EURO3)
(EURO4)
(EURO3)
(EURO4)
D4204T21 (EURO3)
(EURO4) (7CV)
Manual 5 speed (M56L2)
Manual 6 speed (MMT6)
Emissions of CO2
(g/km)
Tank volume
(litres)
7.2
7.2
8.4
9.1
8.5
9.1
8.7
9.4
9.5
10.1
4.9
171
172
199
217
203
217
208
224
227
241
129
55
55
62
5.6
5.7
5.5
5.5
5.6
148
152
145
145
148
Consumption
litre/100 km
62
62
58
55
55
55
1. France
ONR
Technical data
Fuel
Fuel consumption and
emissions of carbon dioxide
Official fuel consumption figures are based
on a standard driving cycle in accordance
with EU Directive 80/1268 comb. Fuel
consumption figures may change if the car is
equipped with extra equipment that affects
the car’s weight. The manner in which the car
is driven and other non-technical factors can
affect fuel consumption. Consumption is
higher and power output lower for fuel with
an octane rating of 91 RON.
ONS
Petrol
Most engines can be run with octane ratings
of 91, 95 and 98 RON.
• 91 RON must not be used in 4 cylinder
engines.
• 95 RON can be used for normal driving.
• 98 RON is recommended for optimum
performance and minimum fuel
consumption.
When driving in temperatures above +38 ºC,
it is recommended to use fuel with the
highest possible octane rating for optimum
performance and fuel economy.
Petrol:
Standard EN 228
Diesel:
Standard EN 590
Technical data
Catalytic converter
Lambda-sondTM oxygen sensor
The Lambda-sond is part of a control system
intended to reduce emissions and improve
fuel economy.
Catalytic converter
An oxygen sensor monitors the oxygen
content of the exhaust gases leaving the
engine. This value is fed into an electronic
system that continuously controls the
injectors. The ratio of air to fuel is continuously adjusted. These adjustments create
optimal conditions for efficient combustion,
and together with the three-way catalytic
converter reduce harmful emissions (hydrocarbons, carbon monoxide and nitrous
oxides).
The purpose of the catalytic converter is to
purify exhaust gases. It is located in the flow
of exhaust gasses close to the engine so that
it quickly reaches operating temperature. The
catalytic converter consists of a monolith
(ceramic or metal) with channels. The
channel walls are lined with a thin layer of
platinum, rhodium and palladium. These
metals act as catalysts, i.e. they participate in
and accelerate a chemical reaction without
being used up themselves.
ONT
Technical data
Electrical system
General
12 volt system with a voltage-regulated alternator. Single pole system in which the
chassis and engine block are used as
conductors.
Battery
Voltage
12 V
12 V
12 V
Cold start capacity (CCA)
520 A
600 A*
700 A**
Reserve capacity (RC)
100 min 120 min 150 min
* Cars equipped with High Performance
audio system.
** Diesel cars with Premium Sound audio
system, fuel-driven heater, RTI.
If the battery is changed, replace it with a
battery of the same cold start capacity and
reserve capacity as the original (see the decal
on the battery).
Alternator
Max. current = 120/150 A1
Starter motor
Output = 1.4/1.9 kW1
1.
ONU
Dependent on engine variant
Technical data
Bulbs
Lighting
1. Dipped beam
2. Bi-Xenon
3. Main beam
4. Brake lights, reversing lamps, rear fog lamp
5. Direction indicators, front/rear (yellow)
6. Rear position/parking lamps, rear side marker lamps
7. Courtesy lighting, cargo area lighting, number plate
lighting
8. Vanity mirror
9. Front position/parking lamps, front side marker lamps
10. Direction indicators in door mirrors (yellow)
11. Fog lamps
Glovebox lighting
Output W
Socket
55
35
55
21
21
5
5
H7
D2S
HB3
BA15s
BAU 15s
BAY15d
SV8.5
1.2
5
5
55
3
SV5.5
W 2.1 x 9.5d
W 2.1 x 9.5d
H11
BA9
ONV
Technical data
OOM
A
Bulb holder ...................................................170
D
A/C ....................................................................68
ABS ................................................................ 111
Additional heater ............................................76
Air conditioning ..............................................66
Air distribution ................................................73
Air distribution, A/C .......................................69
Air quality system, ECC ................................71
Airbag, driver’s side .......................................17
Airbag, passenger side .................................17
Airbags and inflatable curtains,
inspection ........................................................29
Alarm .........................................................96, 97
Alarm signals ...................................................97
Alarm system, test .........................................98
All-wheel drive ............................................. 110
Alternator ...................................................... 218
Approach lighting ..........................................60
Automatic carwashes ................................ 150
C
Defroster ..........................................................69
Diesel particle filter ..................................... 102
Dimensions ................................................... 209
Dipped beam ............................................... 168
Direction indicators ............................ 47, 169
Display ..............................................................43
Door mirrors ....................................................59
Driver’s door control panel ..........................12
DSTC ..................................................... 44, 113
B
Backrest, front seat .......................................78
Backrests, rear ...............................................84
Battery ............................100, 119, 165, 218
Bird droppings ............................................. 150
Bonnet ........................................................... 158
Booster cushion, integrated ........................33
Boot lid .......................................................... 100
Brake fluid ..................................................... 162
Brake system ............................................... 111
Car care .........................................................149
Car upholstery ..............................................150
Carbon dioxide .............................................216
Cargo area ................................. 86, 129, 172
Catalytic converter ......................................217
Child safety ..................................................... 30
Child safety locks .......................................... 95
Child seat, fitting ........................................... 35
Child seats and airbags ............................... 30
Child seats and side airbags ...................... 22
Children in the car, placement ................... 32
Cigarette lighter ............................................. 44
Clean inside and out ........................................3
Cleaning, Car washing ...............................150
Clutch fluid ....................................................162
Cold start ......................................................107
Collision sensors ........................................... 24
Colour code ..................................................152
Combined instrument panel ........................ 38
Compass, calibrating .................................... 58
Condensation ...............................................159
Coolant ..........................................................162
Cooling system ............................................100
Courtesy lighting .........................................171
Crash mode .................................................... 28
Cruise control ................................................. 51
E
ECC ..................................................................67
Economical driving ..................................... 100
Electrical socket in the centre console .....44
Electrical system ......................................... 218
Emissions ..................................................... 215
Engine compartment .................................. 158
Engine oil ............................................160, 212
Engine specifications ................................. 210
Environment ...................................................... 3
Environmental philosophy .............................. 3
Expectant mothers .........................................15
F
Fan, A/C ...........................................................68
Fan, ECC .........................................................70
Floor mats ........................................................83
Fluids ............................................................. 213
OON
Fog lamps ............................................. 45, 170
Fuel consumption .............................215, 216
Fuel consumption, current ...........................48
Fuel filler flap ........................................ 45, 101
Fuel system .................................................. 159
Fuses ............................................................. 173
G
Gearbox, automatic .................................... 107
Gearbox, manual ......................................... 105
Glovebox ..................................................83, 94
Gross vehicle weight ................................. 209
H
Handbrake .......................................................54
Hazard warning flashers ...............................53
Head restraints ...............................................84
Headlamp dipper ...........................................47
Headlamp levelling ........................................45
Headlamp pattern ....................................... 130
Headlamp washer ..........................................49
Headlamps ......................................................45
Heated front seats .........................................69
Heated rear window ......................................69
Heated rearview and door mirrors .............69
Home safe lighting ........................................60
OOO
I
M
Ignition keys ..................................................103
Ignition system ............................................... 91
Immobiliser ............................................88, 103
Indicator symbols .................................. 39, 40
Inflatable curtains .......................................... 24
Information display ........................................ 43
Instrument lighting ......................................... 45
Instrument overview, left-hand drive ............8
Instrument overview, right-hand drive ....... 10
Integrated booster cushion ......................... 33
Interior .............................................................. 77
Interior lighting ............................................... 80
Magnetic zones ..............................................59
Main beam .................................................... 168
Maintenance ................................................. 155
Messages ........................................................43
K
P
Kerb weight ..................................................209
Key .................................................................... 88
Key blade ........................................................ 88
Keyless drive .................................................. 91
Keys .................................................................. 88
Kick-down .....................................................107
PACOS ............................................................20
Paint ............................................................... 152
Paintwork damage ...................................... 152
Panel vents ......................................................66
Parking .......................................................... 115
Parking brake ..................................................54
Parking heater ................................................74
Parking heater, battery and fuel ..................75
Parking heater, parking .................................75
Parking lamps .............................................. 169
Passenger compartment filter .....................66
Petrol grade ................................................. 216
Pinch protection, sunroof .............................62
Polishing ....................................................... 151
Position lamps ..................................... 45, 169
L
Lambda-sond ...............................................217
Lighting ..........................................................167
Lighting panel ................................................. 45
Loading ..........................................................129
Locking ............................................................ 93
Locks ........................................................ 87, 91
Lubricants .....................................................213
N
Number plate lighting ................................ 171
O
Oil filter .......................................................... 160
Oil grade ....................................................... 212
Power steering fluid ................................... 163
Power windows ..............................................55
Puncture repair kit ...................................... 141
R
Rain sensor .....................................................50
Rear fog lamp .................................................46
Rearview mirror ..............................................58
Rearview mirror with compass ....................58
Recirculation, A/C .........................................68
Recirculation, ECC ........................................71
Recovery ....................................................... 117
Refrigerant .......................................................66
Refuelling ...................................................... 101
Relay/fuse box ...................................173, 176
Remote control ...............................................88
Remote control functions .............................88
Reverse gear inhibitor ................................ 106
Reverse gear inhibitor, five-speed .......... 105
Rims ............................................................... 134
RME ............................................................... 159
Rustproofing ................................................ 153
S
Scratches ..................................................... 152
Seat, power seat ............................................79
Seat, seating position ...................................78
Seatbelt reminder ..........................................15
Seatbelt tensioner .........................................16
Seatbelts ............................................... 14, 151
Service programme ....................................156
Side airbags ................................................... 22
Side marker lamps ......................................169
SIPS bag system ........................................... 23
Slippery driving conditions ........................100
Spots ..............................................................150
SRS system .................................................... 19
SRS, switch .................................................... 21
Stability system ......................... 44, 113, 114
Start assistance ...........................................119
Starter motor ................................................218
STC ........................................................44, 113
Steering lock ................................................103
Steering wheel adjustment ......................... 53
Stone chips ..................................................152
Storage spaces ............................................. 82
Sunroof ............................................................ 61
Sunscreen, sunroof ....................................... 62
Switches in the centre console .................. 44
Symbols .........................................................114
T
Tank volume ..................................................215
Temperature selector, ECC ........................ 72
Temperature, A/C .......................................... 69
Timer, A/C ....................................................... 69
Timer, ECC ..................................................... 71
Towbar ................................................ 122, 124
Towing ...........................................................117
Trailer .............................................................120
Trailer weight ............................................... 209
Trip computer .................................................47
Type designation ......................................... 208
Tyre pressure ............................................... 135
Tyres, designation of dimensions ............ 132
Tyres, direction of rotation ........................ 136
Tyres, driving characteristics .................... 132
Tyres, speed ratings ................................... 132
Tyres, tread wear indicators ..................... 133
U
Unlocking .........................................................93
V
Vanity mirror ................................................. 172
Vehicle data ................................................. 156
Viscosity ........................................................ 212
W
Warning symbol, AIRBAG system .............18
Warning symbols ...................................39, 40
Warning triangle ......................................... 137
Washer fluid ................................................. 161
Washing the car .......................................... 150
Waxing .......................................................... 151
Weights ........................................................ 209
Wheel nuts ................................................... 134
Wheels, fitting ............................................. 140
Whiplash injury ...............................................25
OOP
WHIPS .............................................................25
WHIPS and child seat/booster cushion ...25
Windscreen washer ......................................49
Windscreen wipers .......................................49
Winter tyres .................................................. 133
Wiper blades ............................................... 164
OOQ
2005
VOLVO
S40
6968
TP 7459 (English). AT 0446. Printed in Sweden, Elanders Infologistics Väst AB, Mölnlycke 2004
OWNE R'S MANUAL VOLVO S40
TP 7459
2005
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement