null  null
OWNER’S MANUAL
MASTER SPAS OWNER’S MANUAL
Welcome To Ultimate Relaxation!
Thank you for choosing your new spa built by Master Spas. Please read the entire Owner’s Manual
before installing and using your spa. The goal of this manual is to provide you with safety and
operational information plus some tips that will help you enjoy your spa to its fullest.
At the time of print, this manual is accurate in its information. Master Spas reserves the right
to change or improve its product without prior notice. To check on updates or for other information, please visit www.masterspas.com and follow the links to the customer support section.
Record Of Ownership
Name��������������������������������������������������������������������������������
Address ������������������������������������������������������������������������������
City ��������������������������������������������������������� State ������ Zip ���������
Phone # (������)��������-���������� Date Purchased ������ /������ /�������
Model ��������������������������������� Serial #���������������������������������������
Dealer Name �������������������������������������������������������������������������
Service Tech Rep ����������������������������������������������������������������������
Serial Number Location
The serial number for your spa is located near the filter area, on the spa system pack, or on the
listing plate on the skirting. It is a seven digit number. Ex. 1512345
Register Your Spa
Please be sure to register your spa so we can efficiently assist with any questions you may have.
Until your spa has been registered, Master Spas Inc. will not have record of your ownership.
To register your spa, visit www.MasterSpas.com and access our “Customer Support” link on the
page. This area will offer online registration capability along with other support information.
6927 Lincoln Parkway
Fort Wayne, Indiana 46804
www.masterspas.com
DO NOT DIVE.
1
TABLE OF CONTENTS
Record of Ownership�������������������������������������������������������������������������������������������������������������� 1
Table of Contents������������������������������������������������������������������������������������������������������������������� 2
Safety Instructions������������������������������������������������������������������������������������������������������������ 3-10
Glossary of Spa Terminology������������������������������������������������������������������������������������������� 11-13
Site Preparation / General Guidelines������������������������������������������������������������������������������ 14-15
Installation Instructions��������������������������������������������������������������������������������������������������� 16-17
The Advantages of Eco Pur Filtration������������������������������������������������������������������������������������ 18
Water Chemistry Terms You Should Know����������������������������������������������������������������������� 19-20
Why Are Chemicals Important in a Spa�������������������������������������������������������������������������������� 21
Water Maintenance��������������������������������������������������������������������������������������������������������� 22-25
Start-Up������������������������������������������������������������������������������������������������������������������������ 22
Schedule������������������������������������������������������������������������������������������������������������������ 23-24
Troubleshooting Guide�������������������������������������������������������������������������������������������������� 25
Regular Maintenance Procedures������������������������������������������������������������������������������������� 26-30
Spa Troubleshooting Guide��������������������������������������������������������������������������������������������� 31-32
Winterizing & Storing Your Spa�������������������������������������������������������������������������������������������� 33
Spa Care & Maintenance Record�������������������������������������������������������������������������������������� 34-35
Electrical Requirements��������������������������������������������������������������������������������������������������� 36-37
Model Specifications������������������������������������������������������������������������������������������������������������ 38
Spa Controls������������������������������������������������������������������������������������������������������������������� 39-56
Wi-Fi Module (if equipped)��������������������������������������������������������������������������������������������������� 57
Deluxe Fusion Air Stereo Option (if equipped)����������������������������������������������������������������� 58-60
Deluxe Fusion BT Stereo Option (if equipped)������������������������������������������������������������������ 61-69
Mast3rPur (if equipped)�������������������������������������������������������������������������������������������������� 70-72
DO NOT DIVE.
2
SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Included with your new spa is a safety sign. The sign is for you and your guest’s protection
and is suitable for outdoor use in wet locations. The sign should be placed in a location visible
to all users of the spa.
Please take time to point out the physical location of the safety sign and the importance of
the safety precautions displayed on the safety sign to all of your guests. Remember, your safety
and the safety of anyone who enjoys the use of your spa is our utmost concern.
The sign should be mounted with screws or another type of permanent fastener. Additional
or replacement signs can be obtained from your dealer or direct from the factory.
INTRODUCTION
It’s time to relax! You now have your very own portable spa by Master Spas, Inc. By fully understanding the operation of each of the features of your new Master Spa, you will be assured of
many years of hassle-free, hot water therapy and fun.
Your safety is of paramount importance to the MasterSpas family. We urge you to read and
become thoroughly familiar with all safety aspects addressed in this manual.
Through reading and totally understanding the important information in your owner’s manual, you
will realize that you now own THE ULTIMATE RELAXATION MACHINE!
DO NOT DIVE.
100
3
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should
be observed including the following:
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire conductor is provided on this unit to connect a minimum 6 AWG
(13.302mm2) solid copper conductor between this unit and any metal equipment,
metal enclosures of electrical equipment, metal water pipe, or conduit within 5 feet
(1.5m) of the unit
(For cord-connected/convertible units)
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
(For units intended for indoor use only)
WARNING – For indoor use only. This unit is not intended for outdoor use.
(For units intended for outdoor use only)
WARNING – For outdoor use only. This unit is not intended for indoor use.
DO NOT DIVE.
101
4
SAFETY INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS (CONT.)
(For units with GFCI)
WARNING – This product is provided with a ground-fault circuit interrupter
located on the front panel of selected swim spas and on the power cord of
120 volt convertible spas. The GFCI must be tested before each use. With the
product operating, open the service door. When the product stops operating,
this merely indicates that the door is equipped with an electrical interlock.
Next, push the test button on the GFCI and close the service door. The product should not operate. Now open the service door, push the reset button
on the GFCI and close the service door. The product should now operate
normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electric shock. Disconnect the
power until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible.
Never operate spa if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the original suction
fitting.
DANGER – Risk of Electric Shock. Install at least 5 feet (1.5m) from all metal surfaces. As an alternative, a spa may be installed within 5 feet of metal surfaces if
each metal surface is permanently connected by a minimum 8AWG (8.4mm2) solid
copper conductor to the wire connector on the terminal box that is provided for
this purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 40˚C (104˚F). Water temperatures
between 38˚C (100˚F) and 40˚C are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when
spa use exceeds 10 minutes.
DO NOT DIVE.
102
5
SAFETY INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS (CONT.)
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 38˚C (100˚F).
c) Before entering a spa, the user should measure the water temperature
since the tolerance of water temperature- regulating devices varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead
to unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high
blood pressure, circulatory system problems, or diabetes should consult a
physician before using a spa.
f) Persons using medication should consult a physician before using a spa
since some medication may induce drowsiness while other medication may
affect heart rate, blood pressure, and circulation.
(For spas with a gas heater)
WARNING – Risk of Suffocation. This spa is equipped with a gas heater and
is intended for outdoor use only unless proper ventilation can be provided for
an indoor installation.
HYPERTHERMIA
Hyperthermia occurs when the internal temperature of the body reaches a
level several degrees above the normal body temperature of 98.6° F.
THE SYMPTOMS OF HYPERTHERMIA INCLUDE:
• Dizziness • Fainting • Drowsiness • Lethargy
• Increase in Internal Body Temperature
THE EFFECTS OF HYPERTHERMIA INCLUDE:
Unawareness of Impending Hazard • Failure to Perceive Heat • Failure to
Recognize the Need to Exit Spa • Physical Inability to Exit Spa • Fetal Damage
in Pregnant Women • Unconsciousness Resulting in a Danger of Drowning
DO NOT DIVE.
103
6
SAFETY INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS (CONT.)
DANGER – To reduce the risk of injury to persons, do not remove the suction
grate. Suction through drains and skimmers is powerful when the jets in the spa
are in use. Damaged covers can be hazardous to small children and adults with
long hair. Should any part of the body be drawn into these fittings, turn off the
spa immediately. As a precaution, long hair should not be allowed to float in the spa.
WARNING – Install the spa so that water can be easily drained out of the compartment containing electrical components so as not to damage equipment. When
installing the spa make sure to allow for an adequate drainage system to deal with
any overflow water. Please allow for at least 3 feet of clearance around the perimeter of the spa to provide enough room to access for servicing. Contact your local
dealer for their specific requirements.
WARNING – The spa should be covered with an approved locking cover when not
in use, to prevent unauthorized entry and injuries.
WARNING – People with infections, sores or the like should not use the spa. Warm
and hot water temperatures may allow the growth of infectious bacteria if not
properly disinfected.
CAUTION – Safe temperatures for swimming or aquatic exercise is around 80˚F.
CAUTION – Risk of Electrical Shock. Do not leave audio compartment open.
Audio CD controls are not to be operated while inside the spa.
CAUTION – Replace components only with identical components.
WARNING – Risk of Electric Shock. Do not connect any auxiliary components (for
example, additional speakers, headphones, additional audio/ video components
etc.)
to the system. These units are not provided with an outdoor antenna.
Do not service this product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
If the power supply cord(s) are damaged, water is entering the speaker, audio
compartment, or any other component in the electrical equipment compartment
area, the protective shield is showing signs of deterioration, or there are signs of
other potentially hazardous damage to the unit, turn off the circuit breaker from
the wall and refer servicing to qualified personnel.
DO NOT DIVE.
104
7
SAFETY INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS (CONT.)
The unit should be subjected to periodic routine maintenance once every quarter to
make sure that the it is operating properly.
DANGER – Risk of Electric Shock. A green colored terminal or a terminal marked G,
GR, Ground, Grounding or the symbol shown in Figure 14.1 of UL 1563 is located
inside the supply terminal box or compartment. To reduce the risk of electric shock,
this terminal must be connected to the grounding means provided in the electric
supply service panel with a continuous copper wire equivalent in size to the circuit
conductors supplying this equipment.
At least two lugs marked “Bonding Lugs” are provided on the external surface
or on the inside of the supply terminal box or compartment. To reduce the risk
of electric shock, connect the local common bonding grid in the area of the spa
to these terminals with an insulated or bare copper conductor not smaller than
8AWG.
All field installed metal components such as rails, ladders, drains, or other similar
hardware within 3m of the spa shall be bonded to the equipment grounding bus
with copper conductors not smaller than 8AWG.
SAVE THESE INSTRUCTIONS
DO NOT DIVE.
105
8
SAFETY INSTRUCTIONS
WARNING: CHILDREN SHOULD NOT USE SPAS OR HOT TUBS WITHOUT ADULT SUPERVISION
AVERTISSEMENT:
NE PAS LAISSER LES ENFANTS UTILISER UNE CUVE DE RELAXATION
SANS SURVEILLANCE
WARNING: DO NOT USE SPAS OR HOT TUBS UNLESS ALL SUCTION GUARDS ARE
INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT.
AVERTISSEMENT: POUR ÉVITER QUE LES CHEVEUX OU UNE PARTIE DU CORPS
PUISSENT ÊTRE ASPIRES, NE PAS UTILISER UNE CUVE DE RELAXATION SI LES GRILLES DI PRISE
D’ASPIRATION NE SONT PAS TOUTES EN PLACE
WARNING: PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA OR HOT TUB.
AVERTISSEMENT: LES PERSONNES QUI PRENNENT DES MÉDICAMENTS OU ONT
DES PROBLÉMES DE SANTÉ DEVRAIENT CONSULTER UN MÉDECIN AVANT D’UTILISER UNE CUVE
DE RELAXATION
WARNING: PEOPLE WITH INFECTIOUS DISEASES SHOULD NOT USE A SPA OR HOT TUB
AVERTISSEMENT: LES PERSONNES ATTEINTES DE MALADIES INFECTIEUSES NE
DEVRAIENT PAS UTILISER UNE CUVE DE RELAXATION
WARNING: TO AVOID INJURY EXERCISE CARE WHEN ENTERING OR EXITING THE SPA OR
HOT TUB.
AVERTISSEMENT: POUR ÉVITER DES BLESSURES, USER DE PRUDENCE EN ENTRANT
DANS UNE CUVE DE RELAXATION ET EN SORTANT
WARNING:
DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE OF A SPA
OR HOT TUB TO AVOID UNCONSCIOUSNESS AND POSSIBLE DROWNING
AVERTISSEMENT: POUR ÉVITER L’ÉVANOUISSEMENT ET LA NOYADE ÉVENTUELLE, NE
PRENDE NI DROGUE NI ALCOOL AVANT D’UTILISER UNE CUVE DE RELAXATION NI QUAND ON S’Y
TROUVE
WARNING:
PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA OR HOT TUB.
AVERTISSEMENT: LES FEMMES ENCEINTES, QUE LEUR GROSSESSE SOIT CONFIRMÉE
OU NON, DEVRAIENT CONSULTER UN MÉDECIN AVANT D’UTILISER UNE CUVE DE RELAXATION
WARNING: WATER TEMPERATURE IN EXCESS OF 38˚C MAY BE INJURIOUS TO YOUR
HEALTH
AVERTISSEMENT: IL PEUT ÊTRE DANGEREUX POUR LA SANTÉ DE SE PLONGER DANS
DE L’EAU A PLUS DE 38˚C
WARNING: BEFORE ENTERING THE SPA OR HOT TUB MEASURE THE WATER TEMPERATURE WITH AN ACCURATE THERMOMETER
AVERTISSEMENT: AVANT D’UTILISER UNE CUVE DE RELAXATION MESURER LA
TEMPÉRATURE DE L’EAU À L’AIDE D’UN THERMOMÉTRE PRÉCIS
DO NOT DIVE.
106
9
SAFETY INSTRUCTIONS
WARNING: DO NOT USE A SPA OR HOT TUB IMMEDIATELY FOLLOWING STRENUOUS
EXERCISE
AVERTISSEMENT: NE PAS UTILISER UNE CUVE DE RELAXATION IMMÉDIATEMENT
APRÉS UN EXERCISE FATIGANT
WARNING: PROLONGED IMMERSION IN A SPA OR HOT TUB MAY BE INJUROUS TO YOUR
HEALTH
AVERTISSEMENT: L’UTILISATION PROLONGÉE D’UNE CUVE DE RELAXATION PEUT
ÊTRE DANGEREUSE POUR LA SANTÉ
WARNING:
DO NOT PERMIT ELECTRIC APPLIANCES (SUCH AS LIGHT, TELEPHONE, RADIO,
OR TELEVISION) WITHIN 1.5 M OF THIS SPA OR HOT TUB
AVERTISSEMENT:
NE PAS PLACER D’APPAREIL ÉLECTRIQUE (LUMINAIRE, TÉLÉPHONE,
RADIO, TÉLÉVISEUR, ETC) À MOINS DE 1.5 M DE CETTE CUVE DE RELAXATION
CAUTION: MAINTAIN WATER CHEMISTRY IN ACCORDANCE WITH MANUFACTURER’S
INSTRUCTION
ATTENTION: LA TENEUR DE L’EAU EN MATIÉRES DISSOUTES DOIT ÊTRE CONFORME AUX
DIRECTIVES DU FABRICANT
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees
above the normal body temperature of 37˚C. The symtoms of hyperthermia include drowsiness,
lethargy, and an increase in the internal temperature of the body. The effects of hyperthermia
include
(a) unawareness of impending hazard;
(b) failure to perceive heat;
(c) failure to recognize the need to exit spa;
(d) physical inability to exit spa;
(e) fetal damage in pregnant women; and
(f) unconsciousness and danger of drowning.
WARNING:
THE USE OF ALCOHOL OR DRUGS CAN GREATLY INCREASE THE RISK OF
FATAL HYPERTHERMIA IN HOT TUBS AND SPAS
LA CONSOMMATION D’ALCOOL OU DE DROGUE AUGMENTE CONSIDÉRABLEMENT LES
RISQUES D’HYPERTHERMIE MORTELLE DANS UNE CUVE DE RELAXATION.
DO NOT DIVE.
107
10
GLOSSARY OF SPA TERMINOLOGY
Your new Master Spa features a variety of jets. All jets, regardless of style return the water to the
spa. Air is mixed with the water by using the air controls (if equipped) creating a gentle to most
vigorous massage. Water flow is adjusted by simply turning the outer face of the jet. Your Master
Spa may have a combination of pulsating, rotating, dual pulsating and directional adjustable jets.
1. THERAPY JETS
Located throughout the seats of the spa to offer a variety of therapy combinations.
2. NECK JETS (if equipped)
Located above the normal water level to provide massaging action to the back of the neck.
3. SHOULDER JETS (if equipped)
Located above the normal water level to provide massaging action to the shoulders.
4. MASTER BLASTER FOOT THERAPY JET (if equipped)
Large jet with several fixed nozzles located in the bottom of the spa near the floor to provide
excellent massage to the feet.
5. JET DIVERTER VALVE (if equipped)
Located on the top flange of the spa, this large valve physically diverts the flow of water from
one group of jets to another. Be sure that no sand or particles are brought into the spa as they
will cause the diverter to seize up. It is best to turn the diverter valve only when the pump is
turned off.
6. WATER FEATURE VALVE (if equipped)
Located on the top flange of the spa, this smaller valve adjusts water flow to the waterfalls and/
or water features in your spa.
NOTE: When the spa is not in use, this valve should be turned mostly shut (not completely shut)
to prevent the water features from allowing water to hit the cover while it is closed. If
left mostly open, water may hit the cover and possibly run out of the spa causing water
loss.
7. AIR CONTROL VALVE
These smaller valves are located around the top of your spa. You may increase or decrease the
force of your jets by opening or closing the air control valves. Each air control valve will typically function 1 to 2 groups or seats of jets in the spa. When not in use the air controls should
be kept in the closed position as the air being introduced in to the water can tend to cool the
water and increase the dissipation rate of sanitizer levels.
8. TOPSIDE CONTROL PANEL
You may safely control spa functions from inside or outside your spa using the Topside Control
Panel. This Panel is used to control the water temperature, pumps, the spa light, automatic
filtration cycles and other advanced functions. The digital display will give you a constant temperature readout and will notify you in case of certain malfunctions. Several user programmable
functions are also available.
DO NOT DIVE.
100
11
GLOSSARY OF SPA TERMINOLOGY
9.
PERSONAL REMOTE CONTROL (if equipped)
Select spa models may have an additional remote which allows the user to control the jet
therapy while remaining in the seat (if applicable). By pressing the control one time, you will
activate the pump. Press again for high speed and again to turn it off.
10. EQUIPMENT ACCESS PANEL
This is the skirt panel located below the Topside Control Panel. This area houses the majority of components responsible for the spas operation. These components include the pumps,
heater, spa control system, ozonator (if equipped), and LED light system (if equipped). Pump
and equipment placement may vary by model.
11. ACCESS PANELS
These are the skirt panels located around all four sides of the spa. All of the skirt panels are
removable should service be required. Master Spas recommends at least 3 feet of access be
provided around the spa.
12. FILTER LID
This lid fits over the filter area and weir gate to cover the filters. Remove filter lid to access
filters for maintenance.
14. WEIR GATE
The weir gate is the horizontal door located in front of the filters that helps keep debris
trapped in the filter area
15. SPA CONTROL SYSTEM
This houses the wiring and electrical components necessary to operate the spa.
16. SPA HEATER
This is an electric heater housed in a stainless steel tube. It is thermostatically controlled and
equipped with high-limit temperature safety shut-off sensors.
17. SLICE VALVES
These valves are used by service personnel to shut off water
to the heating system (heater and pump plumbed to the
heater) so that the spa water does not need to be drained
if the spa requires service to the heating system (varies by
model).
NOTE: Slice valves must be completely open during normal
operations.
Slice Valve and Pump Union
DO NOT DIVE.
101
12
GLOSSARY OF SPA TERMINOLOGY
18. MAIN THERAPY PUMP
This produces water flow through the main jets in the spa. The first pump may be operated
on two speeds (varies by model). Low speed (if applicable) will produce efficient water circulation during filtration, heating of the spa water, and gentle jet action. High speed provides
maximum jet action. The main pump is controlled by the “Jets” or “Jets I” button on the
Topside Control Panel.
19. SECONDARY THERAPY PUMP (if equipped)
This produces water flow through 1 to 2 groups or seats of jets in the spa. The second pump
operates similar to the main pump and is controlled by the “Jets II” or “Aux” button on the
Topside Control Panel.
20. THIRD THERAPY PUMP (if equipped)
This produces water flow through 1 to 2 groups or seats of jets in the spa. This is controlled
by the Jets III button on the Topside Control Panel.
21. CIRCULATION PUMP (if equipped)
This produces water flow through the heater in the spa and provides the water flow necessary to actuate the ozone injector. This energy efficient pump runs 24 hours for efficient filtration and heating.
22. PUMP UNION
These are used to help relieve possible pump air locks or for service personnel to easily service
the pumps.
23. HEATER UNION
These are used by service personnel to easily service the heater.
DO NOT DIVE.
102
13
SITE PREPARATION / GENERAL GUIDELINES
Portable spa installation is simple when properly planned. It is important that you read the following information carefully and consult with your Master Spas dealer.
1) Access - The actual dimensions of your new spa will determine the amount of space that is
needed in moving the spa from curbside to its final installation area. Be sure to consider and
measure side yard dimensions, gates, doors, overall room dimensions and vertical obstructions such as ceilings, roof overhangs, balconies and overhead cables. Any other space limiting
obstacles such as stairs, trees, and shrubs must also be evaluated. Please be sure to contact and
review these site and installation plans with your Master Spas dealer prior to delivery.
2) Surface/Pad Requirements - When your new spa is filled with water and bathers, it may weigh
as much as several tons. It is imperative that the base beneath the spa can support the entire
weight. The spa must be on a uniformly firm, continuous, and level surface. The recommended
foundation is a concrete pad with a minimum thickness of four (4) inches with steel reinforcement bars crossed throughout the pad.
IMPORTANT
When installing your spa indoors, on a wood deck, roof or balcony; load requirements need to be
evaluated before installation. You should speak with a qualified contractor or your local building
department to confirm that your surface is adequate for supporting a spa.
All sides of the spa must be accessible for regular maintenance or in the event that service is
needed. Periodical maintenance checks require entry into the equipment bay. When possible, it is
wise planning for the future to leave 3 feet of access to all sides of the spa in the event your spa
requires maintenance. Your spa warranty does not cover the cost of providing access for service.
GENERAL CONSIDERATIONS FOR OUTDOOR INSTALLATION
Again, proper planning will increase your total enjoyment factor with your new spa. Listed below
are some additional items to consider when planning your installation.
• How spa will complement landscaping
and vice versa
• Getting to spa from house and return
• View from inside spa and view of spa from
inside of home
• Storage for spa chemicals
• Proximity to dressing rooms and bathrooms
• Local building codes (if applicable)
• Exposure to sunlight and shading from trees
• Power cable
• Privacy
GENERAL CONSIDERATIONS FOR INDOOR INSTALLATION
Installing your spa indoors creates an entirely different set of considerations.
• Work with your Master Spas dealer and
contractor to insure all local building, electrical and plumbing codes are met
• A ventilation fan may be necessary due
to high humidity created by your spa
• Plan for a floor drain to drain off excess water
and for draining and cleaning your spa
DO NOT DIVE.
• Finished material in your spa room should
also be capable of withstanding increased
humidity
100
14
SITE PREPARATION / GENERAL GUIDELINES
GUIDELINES FOR PARTIALLY OR FULLY RECESSED INSTALLATION
Spas manufactured by Master Spas, Inc. are designed to be installed in a variety of settings. One
of which is installing below grade. Should a spa be installed below the level of the site drainage
system (below grade), a system for preventing water collecting and pooling must be designed
based on the requirements of the local authority having jurisdiction. The drainage system must
be designed based on things such as rainfall, water runoff, splashing, draining the spa, etc. that
could potentially feed the below grade area with water. Where located in designated floodways,
additional attention to maximum water load entering the area below grade must be addressed to
prevent water from accumulating below grade at all times. It is generally recommended that the
spa be installed above grade because the spa is not designed to be submerged in water. When a
proper drainage system is designed based on the characteristics of the site, installing the spa below
grade is an accepted method of installation.
• The unit is self-supporting when placed on a surface designed to support the full load of the spa
(see Surface/Pad Requirements). Do not backfill with sand, gravel, or earth. Doing so will void
the warranty.
• Plan for complete drainage so standing water never reaches the electrical equipment.
• Plan for appropriate ventilation so the equipment doesn’t overheat.
• Provide a minimum of 3 feet service area around the perimeter of the unit. Site access issues are
not covered by the product warranty.
• The unit is not designed to be submerged in water. Water entering the equipment area creates
many hazards and resulting damage will not be covered by the product warranty.
• Make sure that the surroundings do not create any additional hazards.
• Surfaces placed around the unit should also be evaluated for walking/slipping hazards from
standing water. Proper drainage is vital to the installation of a below grade installation.
• Check all building, electrical, and plumbing codes with the authority having jurisdiction to ensure
that your installation is in compliance with all local codes.
• Additional consideration needs to be made when installing unit in designed floodways.
• Verify that site specific drainage systems such as down spouts are not going to feed the area
below grade.
• Below grade drainage system needs to be evaluated based on area specific rainfall. One size
does not fit all so an analysis by a qualified, local engineer to ensure proper drainage of all sources of water is a must when installing below grade.
DO NOT DIVE.
101
15
INSTALLATION INSTRUCTIONS
1.
Put spa in final position that allows for access to equipment and spa components. Master
Spas recommends that at least 3 feet of space be provided around all sides of the spa for
access. This provides adequate space for regular maintenance and service.
2.
Remove front skirt panel (this is the side where the topside control panel is located) so
electrical can be hooked up to the spa control system. This panel is removed by unscrewing
the screws securing the skirt corners and the front skirt panel.
3.
With the front skirt panels removed allowing access to the equipment, be sure all pump and
heater unions are secure. Each pump has 2 unions and the heater has 2 unions. A newly
delivered spa may have loose unions caused in transporting the spa. Check that all slice valves
are open, in the up position. The slice valves may become closed during transportation of the
spa.
Slice Valve
and Pump Union
4.
Fill spa at least 1” above the filters or to the minimum water level indication located near the
filter area. We recommend filling the spa through the filter area.
5.
Turn the power on to the spa. Spa will initially display Priming Mode or “Pr”. This lasts
approximately 5-6 minutes. This time is provided to allow each of the pumps to be activated
and checked to ensure they are not air locked from the spa being filled.
6.
Be sure the adjustable jets in your spa are open by turning the face of the jet. Most of the jets
in your spa are adjustable and removable by turning the face of the jet.
DO NOT DIVE.
100
16
INSTALLATION INSTRUCTIONS
7.
It may be necessary to bleed air from the pump(s) in your spa if, after start up, your spa
pumps are turning on and off but you do not have water flow from the jets in your spa.
Due to the nature of water flow and hydro-therapy pumps, please be advised that air locking
of pumps may occur. Master Spas has taken measures to reduce the possibility of this, but it
still may occur, especially after refilling a spa. This is not a service covered under warranty.
To relieve and airlock, loosen the union on the discharge of the pump (see arrow on picture
of pump below). Water should leak out. Tighten the union and test the pump for proper jet
flow. If needed repeat process.
Pump Union
Slice Valve
Airlock
8.
Adjust water chemistry according to the instructions provided in the “Water Maintenance”
section.
9.
Your spa water will heat approximately 3 to 4 degrees per hour with the cover placed on the
spa. This varies depending on the size of the spa and ambient temperatures.
10.
Step into the soothing waters of your Master Spa!
Relax and enjoy.
DO NOT DIVE.
101
17
THE ADVANTAGES OF ECO PUR™ Filtration
Eco Pur™ water filter system is designed to reduce the use of chemicals in your spa. You will still
be required, periodically, based on usage to add a small amount of chlorine to oxidize organic
compounds in the water. The Eco Pur™ filter system will not eliminate the need to maintain proper
water chemistry but can make the maintenance a more natural experience.
FEATURES
• The Eco Pur™ filter system will not oxidize organic compounds and will require periodic doses of
chlorine to assist in the sanitization and oxidation processes required to maintain clear spa water.
• Eco Pur™ filter system will not alter the ph of spa water. The Eco Pur™ filter system will actually
aid in stabilizing the ph. Eco Pur™ does not alter the (TDS) total dissolved solids.
• The main function of the Eco Pur™ filter system is to provide clean and clear spa water.
Proper chemical balance and filtration are also key components in maintaining healthy spa
water. Always ensure that the ph and total alkalinity of the spa water is checked and balanced
at all times. To ensure proper filtration, clean the regular filter cartridge with a “filter cleaner”
every 30 days and rinse the Eco Pur™ cartridge with a hose to remove any buildup of
containments. (Do not soak the Eco Pur™ cartridge in filter cleaner.) If water appears to
be visually cloudy, dull, or has an odor, shock the spa water with 1 ounce of chlorine*
to remove excessive containments. When cleaning filters, be sure to never have the
pumps (including the circulation pump) running without the filters in place. Failure
to do so may result in debris being drawn into the pumps causing unwarranted damage.
• Helps remove calcium carbonate and hydrogen sulphide from spa water to protect heaters
and equipment from precipitation.
• Helps stabilize the pH and alkalinity of the spa water.
• Helps reduce chemical usage and still provide safe odor-free water.
• Helps deplete excess chlorine after chemical shock to prevent damage to skin,
hair, and swim wear.
• Helps to produce ultra clean and clear water.
Note: Eco Pur™ filters are not recommended for use with Bromine. Consult your dealer for additional information.
Master Spas, Inc. products are not designed to be used with Biquanides. These chemicals are found
in SoftSwim® and Baqua Spa® products. Due to adverse effects from these types of sanitizers, the
use of these products may void the spa warranty.
DO NOT DIVE.
100
18
WATER CHEMISTRY TERMS YOU SHOULD KNOW
Before jumping into Water Maintenance, here are some terms to help you.
1.
Parts per million, or ppm: This is a form of measurement used in most pool or spa chemical
readings. Best described as any one million like items of equal size and make up, next to one
unlike item, but of equal size. This would be one part per million.
2.
Average size spa: What is it? The national spa and pool institute (NSPI) states; 350 to 400 U.S.
gallons is average. As a general rule, chemical dosages are the same for any spa between 100
and 500 U.S. gallons. Spas over 500 U.S. gallons the dosage would be double. Under 100
U.S. gallons would be on a case by case basis.
3.
Total Alkalinity: This is a measurement of the ability of the water to resist changes in pH.
Put another way, it is the water’s ability to maintain proper pH. Total alkalinity is measured
in parts per million from 0 to 400 plus, with 100 to 120 ppm being the best range for spas.
With low alkalinity, the pH will flip, or change back and forth, and be hard to control. With
high alkalinity it becomes extremely difficult to change the pH.
4.
pH or potential hydrogen: This is a measurement of the active acidity in the water, or it is
the measurement of the concentration of active hydrogen ions in the water. The greater the
concentration of active hydrogen ions, the lower the pH. pH is not measured in parts per million, but on a scale from 0 to 14, with 7 being the neutral. The pH in spas should be ideally
maintained between 7.4 to 7.6. It should never be below 7.2 or above 7.8. With low pH, the
results can be corroded metals, etched and stained plaster stained fiberglass or acrylic, eye /
skin irritation, rapid chlorine or bromine loss, and total alkalinity destruction. With high pH,
the results can be cloudy water, eye / skin irritation, scale formation and poor chlorine or bromine efficiency.
5.
Shocking: This is when you add either extra chlorine (superchlorinate) by raising the chlorine
level above 8 ppm, or add a non-chlorine /oxidizer (potassium monoperoxysulfate or potassium monopersulfate) to burn off the chloramines or bromamines. A non-chlorine /oxidizer acts
by releasing oxygen in the water, which serves the same function as chlorine. The advantage
to using non-chlorine /oxidizer, is you can enter the water within 15 minutes after application.
Using chlorine, you must wait until the total chlorine reading is below 5 ppm. One thing to
remember, a non-chlorine /oxidizer will not kill bacteria or disinfect.
6.
Sequestering: This can be defined as the ability to form a chemical complex which remains in
solution, despite the presence of a precipitating agent (i.e. calcium and metals). Common
names for sequestering chemicals are; minquest, stain and scale control, metal-x, spa defender, spa metal gone, (etc.).
7.
Filtration: Filters are necessary to remove particles of dust, dirt, algae, etc. that are continuously entering the water. If the spa is not operated long enough each day for the filter to do
a proper job, this puts a burden on the chemicals, causing extra expense. Filtration time will
depend on the spa size, pump and filter size and, of course, bather load. Spare filter cartridges should be kept on hand to make it easy to frequently clean the cartridge without the need
for a long shut down. This will also allow the cartridge to dry out between usages, which will
increase the cartridge life span as much as twice. Replace the cartridge when the pleats begin
to deteriorate. Cartridge cleaning should be done a minimum of once a month. More often
with a heavy bather load.
DO NOT DIVE.
100
19
WATER CHEMISTRY TERMS YOU SHOULD KNOW
8.
Sanitizers: This is what kills the germs and bacteria that enter the water from the environment
and the human body.
A. Chlorine
1. Only one type is approved for spa use. Sodium dichlor which is granular, fast dissolving and pH neutral chlorine.
2. Chlorine is an immediate sanitizer and will be added as needed to maintain free chlorine levels between 2.0 to 4.0 ppm..
B. Bromine (Note: Bromine use is not recommended with Eco Pur filters.)
1. Two types of tablets.
a. Hydrotech
b. Lonza
2. Bromine is a slow dissolve chemical and may take a few days to develop a reserve
or reading in the water. Bromine levels should be maintained between 2.0 to 4.0
ppm.
9.
Total dissolved solids (TDS): Materials that have been dissolved by the water. i.e. Like what
happens when you put sugar in coffee or tea.
10. Useful life of water (in days): Water should be drained at least once every 180 days. Useful life
may vary by usage and bather load.
11. Defoamer: Foaming may be caused by body oils, cosmetics, lotions, surface cleaners, high
pH or algeacides as well as other organic materials. Low levels of calcium or sanitizer can
also cause foaming. Also, double rinse your bathing suits as they will hold residual soap after
being washed.
12. Calcium hardness: Water that is too hard (over 250 ppm) can promote scale formation in
components and on spa surface. Water that is too low (below 150 ppm) may also shorten
the life of metal components on the spa.
NOTE: Always leave spa cover open for 15 minutes after adding chemicals to prevent the off
gas from damaging your spa cover, spa pillows, stainless steel hardware and other critical
parts.
DO NOT DIVE.
101
20
WHY ARE CHEMICALS IMPORTANT IN A SPA
1.
Evaporation:
As water evaporates, only pure water evaporates, leaving the salts, minerals, metals, and any
unused chemicals behind. Adding water adds more salts, minerals, and metals. In time, the
water can become saturated with these dissolved solids and can cause stains or scale to form
on the walls of the spa or a scale build up inside the equipment. Colored or cloudy water,
and possible corrosion of plumbing and fittings may also occur.
2.
Heat:
Heat causes much quicker evaporation and also will cause minerals and metals to precipitate
out of solution.
3.
Air:
Dust and other airborne contaminants are introduced into the spa.
4.
Environment:
The environment surrounding the spa can also impact the water quality. Items such as pollen, grass, sand, dirt, lawn fertilizer, airborne dust, insects, leaves, and pets can all affect the
water quality of the spa.
5.
Bathers:
As the spa is used, bathers introduce contaminants to the water. Increased bather load,
length of use and frequency will increase the amounts of contaminants added in to the
water.
Remember:
The maintenance routines set forth in this manual may need to be adjusted depending on bather
load and how much the spa is being used.
DO NOT DIVE.
100
21
WATER MAINTENANCE – START-UP
Step 1:
Your spa should be filled using a Pre-filter, which can be obtained from your local
dealer. This Pre-filter will help remove many of the minerals existing in the water,
which will make adjusting the water balance easier after a new fill. Never use more
then 50% softened water when filling the spa.
Step 2:
During the initial filling of the spa, add a sequestering agent to combat suspended
minerals in the water. The agents are sold under many different names such as Mineral
Clear, Stain and Scale, Metal Protect, and other brands. Allow water to circulate and
filter for at least 12 hours before adding any other chemicals.
Step 3:
Test water for pH, total Alkalinity, and Calcium hardness. The pH should be 7.4 - 7.6
and the total Alkalinity 100 - 120 ppm. Calcium hardness levels should be maintained
between 150 and 250 ppm (part per million).
Step 4:
Adjust pH and total Alkalinity (TA) utilizing the directions on the chemical bottles.
Wait 15 minutes, test and adjust if necessary.
Step 5:
It may be necessary to retest and add additional chemicals to get to the proper levels
in Step 3.
Step 6:
Add concentrated chlorinating granules* (sodium Dichlor-s-triazinetreone) to reach a
Free Chlorine level of 5 to 8 ppm on initial start up to begin sanitizing the spa water.
Bathers should not enter the spa until the chlorine levels drop below 5.0 ppm. Always
refer to the chemical manufactures dosage recommendations listed on the container.
It is important not to add the chlorinating granules until the pH, alkalinity and calcium
hardness have been adjusted to their proper levels.
*SPECIAL NOTE:
We recommend a minimum level of 2.0 ppm residual free chlorine be maintained in spa water. Always refer to
the chemical manufacturer’s dosage recommendations listed on the container.
When adding chlorine or non-chlorine shock/oxidizer always broadcast across the water while the pumps are
running.
The quantities of sanitizer and oxidizer shown in this manual are for 500 gallon spas and may have to be adjusted depending on the actual amount of water that your spa holds. See the specifications section of this manual
for the correct gallons of your spa.
The concentration of active ingredients in spa chemicals varies by manufacturer. The amounts of sanitizer suggested in this manual are based on spa chemicals that have the active ingredient percentages listed below:
Chlorine
Non-Chlorine Shock/ Oxidizer
Active ingredient:
Active ingredient:
Sodium dichlor ................................. 99%
Potassium peroxymonosulfate ....................... 42.8%
Other ingredients ................................ 1%
Inert ingredients ............................................ 57.2%
Total ............................................... 100%
Total............................................................ 100%
DO NOT DIVE.
100
22
WATER MAINTENANCE – SCHEDULE
BEFORE EACH USE
Check spa water with a test strip for proper sanitation levels and adjust accordingly to the proper
levels. Free chlorine level should be 2.0 - 4.0 ppm. Appropriate levels should be present before use
of the spa. Bathers should not enter the spa if total chlorine levels are above 5.0 ppm or if free
chlorine levels are below 2.0 ppm.
ONCE A WEEK
Add non-chlorine shock/oxidizer* or chlorine* to spa to help maintain the water quality.
3 TIMES A WEEK
Test water using chemical test strips. Adjust sanitizer, pH and Alkalinity accordingly. The total alkalinity should be between 100 - 120 ppm and the PH should be between 7.4 - 7.6. If free chlorine
level measures less than total chlorine level, additional non-chlorine shock/oxidizer* treatment is
necessary.
ONCE A MONTH
Soak your regular filter elements overnight in a container with spa Filter Cleaner and then rinse
with clean water. For best results, allow the filter to dry before re-inserting. (The Eco Pur™ mineral
element should never be cleaned in a filter cleaner. Just rinse with water.) When cleaning filters, be
sure to never have the pumps (including the circulation pump) running without the filters in place.
Failure to do so may result in debris being drawn into the pumps causing unwarranted damage.
See the “clean your filter elements” in the maintenance section of this manual for more information.
EVERY 180 DAYS
Drain and refill your spa with fresh water, install a new Eco Pur™ filter element, clean the regular
filter, and repeat start up procedure. The regular filter should be replaced at least once every year.
AFTER EACH USE
Add non-chlorine shock/oxidizer* or chlorine* to the spa water.
*SPECIAL NOTE:
We recommend a minimum level of 2.0 ppm residual free chlorine be maintained in spa water. Always refer to
the chemical manufacturer’s dosage recommendations listed on the container.
When adding chlorine or non-chlorine shock/oxidizer always broadcast across the water while the pumps are
running.
The quantities of sanitizer and non-chlorine oxidizer shown in this manual are for 500 gallon spas and may have
to be adjusted depending on the actual amount of water that your spa holds. See the specifications section of
this manual for the correct gallons of your spa.
The concentration of active ingredients in spa chemicals varies by manufacturer. The amounts of sanitizer suggested in this manual are based on spa chemicals that have the active ingredient percentages listed below:
Chlorine
Non-Chlorine Shock/ Oxidizer
Active ingredient:
Active ingredient:
Sodium dichlor ................................. 99%
Potassium peroxymonosulfate ....................... 42.8%
Other ingredients ................................ 1%
Inert ingredients ............................................ 57.2%
Total ............................................... 100%
Total............................................................ 100%
DO NOT DIVE.
100
23
WATER MAINTENANCE – SCHEDULE
AS NEEDED
If water looks hazy, check PH and Total Alkilinity, and treat with chlorine*. Always refer to the
chemical manufactures dosage recommendations listed on the container. Free chlorine levels
should be maintained between 2.0 - 4.0 ppm.
These are general recommendations for water maintenance that may vary by usage and bather
load. Depending on bather load and frequency of use, drain and refill times may vary as well as the
frequency of cleaning your filters.
A defoamer may be used when excessive foaming occurs. Over use of a defoamer will result
in cloudy, milky water.
USE ONLY SPA CHEMICALS
Do not use chemicals designed for use in swimming pools.
With a spa you are working with a small volume of hot water compared to a large volume of
relatively cool water in a swimming pool. Because of this chemicals will have a shorted life span
and bacteria can grow more quickly than in a swimming pool. A spa is less forgiving then a pool
and requires that whatever is put into it have a pH as close to neutral as possible. That is why only
chemicals made for spas should be used. Always refer to the chemical manufactures dosage recommendations listed on the container.
*SPECIAL NOTE:
We recommend a minimum level of 2.0 ppm residual free chlorine be maintained in spa water. Always refer to
the chemical manufacturer’s dosage recommendations listed on the container.
When adding chlorine or non-chlorine shock/oxidizer always broadcast across the water while the pumps are
running.
The quantities of sanitizer and oxidizer shown in this manual are for 500 gallon spas and may have to be adjusted depending on the actual amount of water that your spa holds. See the specifications section of this manual
for the correct gallons of your spa.
The concentration of active ingredients in spa chemicals varies by manufacturer. The amounts of sanitizer suggested in this manual are based on spa chemicals that have the active ingredient percentages listed below:
Chlorine
Non-Chlorine Shock/ Oxidizer
Active ingredient:
Active ingredient:
Sodium dichlor ................................. 99%
Potassium peroxymonosulfate ....................... 42.8%
Other ingredients ................................ 1%
Inert ingredients ............................................ 57.2%
Total ............................................... 100%
Total............................................................ 100%
DO NOT DIVE.
101
24
WATER MAINTENANCE –
TROUBLE-SHOOTING GUIDE
PROBLEM
POSSIBLE CAUSES
HOW TO FIX IT
Chlorine / Bromine Odor
• Excessive Chlorine or
bromine levels
• Shock water with non-chlorine
shock treatment
• Low pH
• Adjust pH if necessary
• Low levels of sanitizer
• Shock water with non-chlorine
shock treatment or adjust sanitizer levels
• pH out of range
• Adjust pH level if necessary
• Bacteria or algae growth
• Adjust sanitizer if necessary
• Dirty filters or
inadequate filtration
• Clean filters and adjust filtration
times
• Water chemistry not balanced
• Adjust chemistry levels
• Suspended particles or
organic materials
• Add spa clarifier (see dealer)
Water Odor
Cloudy Water
• Old water
• Change spa water
Scum Ring Around Spa
• Build up of oils, dirt and
organic elements
• Wipe off with a clean towel add
an enzyme product.
Eye / Skin Irritation
• Unsanitary water
• Shock spa with non-chlorine
shock
• Free chlorine level above 5 ppm
• Allow level to drop below 5 ppm
• Poor sanitizer / pH levels
• Adjust according to spa test strip
results
Foaming
• High levels of body oils,
lotions, soap, etc.
• Add small amount of defoamer
Deep Blue Water Color
or Colorful Deposits
Precipitating from Water
• Excessive build up in the
water from total dissolved
solids, bather load and chemical treatments over time
• Draining and fresh fill of water
may be required
• Reaction between substances
in water and types or excessive amounts of chemicals
added to water
*RECOMMENDED LEVELS OF CHEMICAL
Free Chlorine 2.0 - 4.0 ppm
pH 7.4 - 7.6
Total Alkalinity 100 - 120 ppm
Calcium Hardness 150 - 250 ppm
*Recommended levels stated in this manual are based on industry standards for permanently installed and portable residential spas
and swim spas.
DO NOT DIVE.
100
25
Regular Maintenance Procedures
Note: These are areas that will require the spa owner to perform routine maintenance. These are not
areas covered under the warranty of the spa.
Your spa requires periodic draining and cleaning to ensure a safe, healthy environment. It is recommended that you clean your spa at least every 180 days or as necessary. Heavy bather load will
require cleaning it more often.
DRAINING YOUR SPA
• The spas are equipped with a drain assembly which can be located on the front side of the spa
behind the skirt (same side as the topside control panel or where most of the spa equipment is
located). Location varies by model. The drain will either be mounted to the front, right corner at
the base of the frame (Figure 1) or will be located in the equipment area behind the front skirt
panel (Figure 2).
Figure 1: Access to the drain can be gained by removing the
panel screws or thumb screws from the front, right corner
panel. The drain should be mounted at the base of the corner
as shown in Figure 1. If your model does not have a drain
located in the base of the corner, proceed to the steps for
Figure 2.
Figure 1
Grasp the drain cap, and pull the assembly out as far as it will
go. Unscrew the cap from the assembly. Push the drain back
in midway to start the flow of water. A garden hose can be
attached to the end of the drain assembly, if so desired.
Figure 2: Access to the drain can be gained by removing both front corner skirt panels. To do so,
remove the screws or thumbscrews from the corner panels. Next, remove the front skirt panel
by removing its panel screws. The drain will be located inside the equipment bay (see Figure 2 &
Figure 2.1). To start the flow of water with this drain assembly; remove the cap, twist the face
counterclockwise and pull out slightly on the face. A garden hose can be attached to the end of
the drain assembly, if so desired.
Figure 2
Figure 2.1
NOTE:
• With the cap removed from the drain; water may drip or weep from the drain. This is normal. Be
sure that the steps are followed in reverse order when draining is finished. Make sure that the
drain cap is reattached and the valve is put back to the fully closed position so that there is no
water leaking from the drain assembly.
• Draining times will vary by model using the drain assembly. A sump pump may also be used to
expedite the draining of the spa.
DO NOT DIVE.
100
26
REGULAR MAINTENANCE PROCEDURES
Note: These are areas that will require the spa owner to perform routine maintenance. These are not
areas covered under the warranty of the spa.
CLEAN YOUR SPA SURFACE
• With a soft cloth, wipe down the spa surface with a non-abrasive spa surface cleaner that may
be purchased through your local spa dealer. Do not use paper towels. Be sure to rinse residue
from spa surface.
• If your spa has developed an oily or chalky residue at the waterline it may require special treatment. Consult your dealer.
CLEAN YOUR FILTER ELEMENTS
The filter elements are one of the most important components of your spa. Not only are they
essential for clean water, but they also extend the life of the spa equipment. Your filter elements
should be cleaned on a regular basis, once a month on average with normal usage. With heavy
use the filters may need to be cleaned more often.
• Turn off the spa before servicing filters. Never leave to the spa running when removing the filters. Debris can be pulled into the plumbing system and cause unwarranted damage.
• Remove filter element(s).
• With a garden hose, spray each element under pressure. Periodically, the standard filter elements
need to be soaked in a filter cleaner compound. Do not soak Eco Pur mineral filters in a filter
cleaner. Eco Pur filters should only be rinsed with fresh, clean water as necessary. Check with
your dealer for details on cleaning and/or filter replacement recommendations.
• The Eco Pur Mineral filter should be replaced every 6 months. The standard filter should be
cleaned regularly and will typically last approximately 1 year. Bather load, usage and water quality will effect the longevity of the filters and require more frequent cleaning or replacement.
CARE OF YOUR SPA PILLOWS
• Your spa pillows need to be rinsed periodically to remove any chemical residue. This should help
to eliminate pillows becoming stiff and discolored.
• If spa is not to be used for a period of time, pillows should be removed. Pillow life will be extended.
NOTE: Do not cover the spa for 15 minutes after adding chemicals as the off gas can cause unwarranted damage.
DO NOT DIVE.
101
27
REGULAR MAINTENANCE PROCEDURES
Note: These are areas that will require the spa owner to perform routine maintenance. These are not
areas covered under the warranty of the spa.
CLEANING JETS
The majority of jets in your spa can individually be turned on/off. If any of these jets become hard
to turn, it will be necessary to remove the jet to clean it as grit/sand and mineral deposit may be
present.
The jets in your spa can be removed for cleaning by unscrewing them (counter clockwise) and then
pulling out the jet.
To Clean Jets
Place the jet(s) in a container, fully immerse in white vinegar. Let the jet(s) soak overnight and then
rinse with water. Reinstall the jet(s). It may be necessary to clean grit and deposits from the white
jet body (mounted in the spa shell) by using a small bristled brush.
CLEANING DIVERTER VALVES
Due to mineral deposits and grit/sand that may get into the internal parts of the diverter valve, it
may become hard to turn or freeze up completely. Excessive force applied to turn the valves can
cause unwarranted damage to the valve. In this case, it is necessary to remove the handle and cap
of the diverter valve. Before proceeding, make sure the power to the spa is turned off.
Turn the cap piece counter clockwise. It may be necessary to put a clean cloth over the cap and
turn it with a wrench.
Once loose, the cap and handle can be pulled up out of the white plumbing fitting.
Wipe down the internal piece that attaches to the cap and handle.
Soak the cap and handle in white vinegar.
The white plumbing fitting should also be wiped down. If the surface of the white plumbing has
become too abrasive, you can take wet, fine sandpaper and smooth it out. It is also helpful to use
a lubricant (use silicone based, not petroleum based) to allow for an easier turn of the diverter
handle.
Rinse the diverter internals and reassemble.
In the future, it is helpful to turn the diverter valve only when the pump is not on. Cleaning your
diverter valve should occur every time you drain your spa.
DO NOT DIVE.
102
28
REGULAR MAINTENANCE PROCEDURES
Note: These are areas that will require the spa owner to perform routine maintenance. These are not
areas covered under the warranty of the spa.
CARE OF YOUR SPA COVER
Always cover your spa when not in use. This will greatly reduce energy consumption and will cause
spa water to heat more rapidly. Water loss and chemical usage will also be reduced.
• Be sure to lock down all straps on cover after each use to prevent wind damage.
• Do not allow spa to sit uncovered in direct sunlight. This may cause damage to exposed surfaces
and components of the spa and possible discoloration of spa fittings.
• Periodically hose off both sides of spa cover for maximum life of cover. Once a month use a vinyl
cleaner and conditioner on the vinyl portion of your cover. Rinse residue off.
• Keep cover open for 15 minutes after adding chemicals to prevent off gas damage.
NOTE: if your spa is going to be left empty for prolonged periods, do not replace cover directly on
surface of spa. Place 2”-3” blocks between cover and spa. This allows for adequate ventilation of cover and spa.
NOTE: The cover warranty is not part of the limited warranty provided with the spa. It is provided
through the cover manufacturer and may not be through Master Spas. Check the tags and
labeling on your cover to verify manufacturer and refer to the manufacturer’s care, maintenance and warranty information. Your dealer can help provide you with these details.
NOTE: To prevent premature failure of your spa cover, always turn water feature valve down so
that the water features do not hit the cover when the cover is closed.
CARE OF YOUR SPA CABINET
Your skirt is maintenance free. No conditioning is necessary. Simply rinse off the waterproof / U.V.
resistant material periodically with fresh, clean water.
CARE OF YOUR OZONE SYSTEM
The ozone hose and check valve connecting between the ozone generator and ozone injector should
be inspected and/or replaced, if necessary, every 12 months. Depending on conditions of the air
which is being brought in to the ozone generator, the ozone hose and check valve can wear more
rapidly. This regular maintenance is not covered under the spa warranty. Your Master Spas Dealer or
Service Center can be contacted to schedule this maintenance.
DO NOT DIVE.
103
29
Regular Maintenance Procedures
Note: These are areas that will require the spa owner to perform routine maintenance. These are not
areas covered under the warranty of the spa.
STAINLESS STEEL
Master Spas uses stainless steel in a number of our spas. Its lasting beauty and resistance to corrosion make it an excellent material for handrails and jets faces.
With the proper care it will keep its luster for many years. All stainless steel can corrode given the
right circumstances so we have provided a guide to help you keep the stainless components in
your spa looking nice.
Stainless steel derives its ability to resist corrosion by forming a very thin transparent coating on the
surface when exposed to oxygen. This coating can be damaged by abrasive materials such as steel
wool, sand paper, and other cleaning materials that are abrasive. Chlorine salts, sulfides, or other
rusting metals can also erode this thin coating exposing the metal to corrosion.
The best defense to combat corrosion on stainless steel components in your spa is make sure that
it is kept clean and free of any chemical build up.
Always:
• Clean frequently with clear, clean, non-chlorinated water.
• Remove any rust spots as soon as they appear with vinegar or a brass, silver, or chrome cleaner.
• Use a good car cleaning wax for extra protection.
• Leave cover removed from the for at least 15 minutes after adding chemicals to the spa water.
Never:
• Clean with mineral acids or bleaches.
• Clean with steel wool or any other abrasive material.
• Leave in contact with iron, steel any other metals.
• Close the cover immediately after adding chemicals to the water.
NOTE: Failure to take proper care of the stainless steel fixture could result with them
rusting. Rusting is not covered by the warranty.
NOTE: Do not cover the spa for 15 minutes after adding chemicals as the off gas can
cause unwarranted damage. Larger dosages can require longer lengths of time to
off gas. It is recommended to check spa water more frequently to allow small dosages be added as necessary verse large dosages being added less often.
DO NOT DIVE.
104
30
SPA TROUBLE SHOOTING GUIDE
Note: For wiring outside of U.S. and Canada, GFCI may be referred to as a RCD (residual current
device). Be sure all local electrical codes are followed.
NOTHING ON THE SPA OPERATES
1. Check the control panel display for any messages. If there is a message, refer to the diagnostic
section on that model spa. There you will find the meaning of the message and what action is
to be taken.
2. If there is no message on your control panel, check and reset the GFCI and house breaker.
The GFCI should be located in a weather proof box close to the spa,
but no closer than 5 ft.
If the spa does not respond, contact your local service company.
PUMP(S) DO NOT OPERATE 1. Press the “Jets” button on your control panel.
If you hear the pumps trying to operate:
A. Check that all the slice valves are open.
B. Pump may need to be primed.
C. Check that all jets are in their full open positions.
If you do not hear anything from the pump, contact your local dealer or service company.
POOR JET PERFORMANCE
1. Make sure pump is operating
2. Check that the water level is adequate (up to minimum safe water level)
3. Make sure the jets are open and the air controls are open.
DO NOT DIVE.
100
31
SPA TROUBLE SHOOTING GUIDE
Note: For wiring outside of U.S. and Canada, GFCI may be referred to as a RCD (residual current
device). Be sure all local electrical codes are followed.
SPA NOT HEATING
If the spas heater has failed, the majority of the time it will trip the GFCI breaker. If the spa is not
heating and has not tripped the breaker, please follow these steps:
1. Check the topside control panel for diagnostic messages. Refer to your spa models diagnostic
message area. Follow steps to alleviate message.
2. Check water set temperature at topside control panel.
3. Check for dirty filters. Clean or replace if necessary.
4. Check “heat mode” the spa is set in. Spa should be in standard/ready mode.
5. Check the control panel for heater indicator, see controls section of manual. If the indicator is
on, the spa should be heating. With the cover closed on the spa, wait a reasonable amount of
time (approximately 1 to 2 hours) to see if the water temperature is increasing.
6. Check to make sure that the pump is primed and all slice valves are open.
7. Reset power to the spa at GFCI breaker.
8. If spa is still not heating, contact your dealer for service.
GFCI IS TRIPPING
A ground fault circuit interrupter (GFCI) is required by the National Electrical Code for your
protection. The tripping of the GFCI may be caused by a component on the spa or by an electrical
problem. Electrical problems include but are not limited to, a faulty GFCI breaker, spa component,
power fluctuations, or improper wiring. If this is a new electrical service and GFCI installation, an
instantly tripping GFCI may likely be caused by improper wiring of the load neutral from the GFCI
to the spa. It may be necessary to contact an electrician if your dealer recommends doing so.
DO NOT DIVE.
101
32
Winterizing & Storing Your Spa
Winterizing Your Spa
Many people find they enjoy using their spa more in the winter than any other time. Your spa is
designed to be used year round in any type of climate.
*However, if you decide you don’t want to use your spa in the winter, you must drain it and follow the winterizing steps listed below:
1.
Drain your spa completely using the drain valve (if so equipped) or use an inexpensive submersible pump that you can buy from your dealer or your local hardware store.
2.
Use a shop vac to get all standing water out of your unit.
3.
Remove access panels from equipment area.
4.
Loosen and disconnect all pump unions and heater unions.
5.
Remove winterizing plug from face of the pump(s) where applicable.
6.
Using your shop vac in a blowing mode, insert the hose into the nozzle of each jet and blow
the trapped water from the lines into the interior of the spa. A non-toxic, RV water line type
antifreeze can be used and added to jets in each seat around your spa to help prevent freeze
damage from occurring. Be sure to thoroughly flush the system before startup.
7.
After this is completed, use the shop vac to remove any standing water in the spa and in the
equipment area.
8.
Clean the spa with a soft cloth and a non-abrasive spa surface cleaner.
9.
Replace access panels.
10. Cover spa to prevent water from entering the spa.
*Disclaimer: Master Spas does not recommend winterizing your spa. If you choose to do
so, any damage that may result is not covered under the spa warranty.
Storing Your Spa
The spa shell should never be left unprotected and uninsulated while being stored. Clear plastic
wrap or similar material should never be used to cover/protect the spa.
Prolonged, direct sun heat can damage the surfaces of the spa along with any components on the
spas surface. Always keep the spa covered and protected with an insulating spa cover. Resulting
damage such as cracking in the shell surface or warped or discolored components on the spa shell
would not be warranted.
An empty spa should never be exposed to temperatures below 0°F (-18°C) after delivery as
extreme cold can cause shell damage. This includes storage and draining (winterizing). If your spa
can be exposed to these temperatures, keep the unit filled and running. If you do not plan to use
your spa, you can set the spa to the lowest temperature setting allowed by the control system.
Failure to adhere to these guidelines will void the warranty.
DO NOT DIVE.
100
33
SPA CARE AND MAINTENANCE RECORD
DATE
DATE
DATE
Drain & Clean Spa
Clean Filter Cartridge
Soak Filter
Cartridge in Solution
Test GFCI
Clean and Condition
Spa Cover
Miscellaneous
Service
Miscellaneous
Service
DO NOT DIVE.
100
34
DATE
DATE
DATE DATE
DATE
SPA CARE AND MAINTENANCE RECORD
DATE
DATE
DATE
Drain & Clean Spa
Clean Filter Cartridge
Soak Filter
Cartridge in Solution
Test GFCI
Clean and Condition
Spa Cover
Miscellaneous
Service
Miscellaneous
Service
DO NOT DIVE.
100
35
DATE
DATE
DATE DATE
DATE
ELECTRICAL REQUIREMENTS
Configuration 2 - 240V, 50A GFCI
Note: Electrical requirements by model is shown in Model Specifications. Only electrical configurations pertaining to the models referenced in this manual are shown.
ELECTRICAL REQUIREMENTS
HAVE YOUR ELECTRICIAN READ THE FOLLOWING INFORMATION
BEFORE INSTALLATION BEGINS
Electrical connections made improperly, or the use of wire gauge sizes for incurring
power which are too small, may continually blow fuses in the electrical equipment
box, may damage the internal electrical controls and components, may be unsafe
and in any case will void your warranty.
It is the responsibility of the spa owner to ensure that electrical connections are
made by a qualified electrician in accordance with the National Electrical Code and
any local and state electrical codes in force at the time of installation.
These connections must be made in accordance with the wiring diagrams found
inside the control box. This equipment has been designed to operate on 60Hz.
alternating current only, 240 volts are required. Make sure that power is not
applied while performing any electrical installation. A copper bonding lug has been
provided on the electrical equipment pack to allow connection to local ground
points. The ground wire must be at least 8 AWG copper wire and must be connected securely to a grounded metal structure such as a cold water pipe. All Master
Spas equipment packs are wired for 240 VAC only. The electrical service for your
spa must include a 50 AMP switch or circuit breaker to open all non-grounded
supply conductors to comply with section 422-20 of the National Electrical Code.
The disconnect must be readily accessible to the spa occupants, but installed at
least five feet from the spa. A Ground-Fault Circuit Interrupter (GFCI) must be
used to comply with section 680-42 of the National Electrical Code. A ground
fault is a current leak from any one of the supply conductors to ground. A GFCI
is designed to automatically shut off power to a piece of equipment when a ground
fault is detected.
Service to the spa must be dedicated 240V, 50A 3 wire plus ground (#6 AWG
copper with minimum #8 AWG copper ground).
Route service into the equipment area for final hook-up to terminals inside the
spa control system. The spa must be hooked up to a “dedicated” 240 volt, 50 amp
breaker and GFCI. The term “dedicated” means the electrical circuit for the spa
is not being used for any other electrical items (patio lights, appliances, garage
circuits, etc.). If the spa is connected to a non-dedicated circuit, overloading will
result in “nuisance tripping” which requires resetting of the breaker switch at the
201412
house electrical panel.
Permanently Connected Equipment Assembly with Pump(s), Heaters, Luminaine, Ozone, Spa Side
Control(s), Pump shut off device, and Audio/Video Components.
Note: Some of the above components may be optional or not available with every spa model.
DO NOT DIVE.
100
36
ELECTRICAL REQUIREMENTS
Configuration 2 - 240V, 50A GFCI
MAIN ELECTRICAL PANEL
(HOUSE)
Key
50
WHT - White Neutral
BLK - Black Hot, Line 1
RED - Red Hot, Line 2
GND - Ground
BLK
RED
WHT
GND
WHT
GND
BLK
RED
50 AMP GFCI
GND
50A
TEST
BLK
WHT
RED
CONFIGURATION 2
240V, 50A GFCI
DO NOT DIVE.
WHT
WHT
*SPA CONTROL
SYSTEM
BLK
RED
GND
101
37
*Refer to wiring diagram
inside spa control system
for proper power
connection to terminals.
Model SPECIFICATIONS
Model
Listing
Spa Dimensions
Number
1
Electrical
Requirements
Seating
Capacity
Weight
Water
Capacity Dry / 2Full
(gallons) (lbs.)
Therapy
Pumps
TS 240
6200
78" x 78" x 34"
Configuration # 2
240V, 50A GFCI
2-3
205
515 /
2780
2
TS 6.2
5300
78" x 78" x 34"
Configuration # 2
240V, 50A GFCI
5
250
630 /
3640
2
TS 67.25
8000
70" x 84" x 34"
Configuration # 2
240V, 50A GFCI
4-5
245
530 /
3500
2
TS 7.2
5500
84" x 84" x 38"
Configuration # 2
240V, 50A GFCI
5-6
305
755 /
4410
2
TS 7.25
6400
84" x 84" x 38"
Configuration # 2
240V, 50A GFCI
6-7
305
785 /
4625
2
TS 8.2
5700
94" x 94" 38"
Configuration # 2
240V, 50A GFCI
6
380
755 /
5035
2
TS 8.25
7700
94" x 94" 38"
Configuration # 2
240V, 50A GFCI
7
395
755 /
5345
2
TS 8.3
6000
94" x 94" 38"
Configuration # 2
240V, 50A GFCI
6
385
805 /
5130
3
TS 8.35
7800
94" x 94" 38"
Configuration # 2
240V, 50A GFCI
7
400
805 /
5440
3
TS 87.3
1450
94" x 84" 38"
Configuration # 2
240V, 50A GFCI
5
310
780 /
3370
3
See Electrical Requirements Section.
1
Full weight based on dry weight of spa, max seating capacity of spa, assumed average weight per
person of 185 pounds and estimated water weight of 8.34 pounds per gallon.
2
DO NOT DIVE.
38
SPA CONTROLS
The Main Screen
SPA STATUS
Important information about spa operation can be seen quickly from the Main Screen.
The most important features, including Set Temperature adjustment, can be accessed from this
screen.
The actual water temperature can be seen in large text and the desired, or Set Temperature, can
be selected and adjusted.
Time-of-day, Ozone operation and Filter Operation status is available, along with other messages
and alerts.
High Temperature Range vs. Low Temperature Range is indicated in the upper right corner.
The Jets Icon in the center will indicate when a pump is running and also the heater function.
A Lock icon is visible if the panel or settings are locked.
The Menu choices on the right can be selected and the screen will change to show more detailed
controls or programming functions.
Water
Temperature
Desired
Temperature
Temperature
Range
Pump
and Heat
Status
102°F
Set: 104°F
8:32 PM
Ozone
Filter 1
High Range
Spa
Scene
Settings
Ready in Rest Mode
Heating
Messages
Menus
Lock
Indicator
DO NOT DIVE.
39
SPA CONTROLS
The Main Screen
NAVIGATION
Navigating the entire menu structure is done with the 5 buttons on the control panel.
When a text item changes to white during navigation, that indicates the item is selected for action.
Operating or changing a selected item is generally done with the center or “Select” button.
The only item that can be changed on the left side of the Main Screen is the Set Temperature.
Press the Left Arrow button to change the Set Temperature number to white. The Set Temperature
can then be adjusted with the up and down buttons. Pressing the Select button or the Right Arrow
button will save the new set temperature.
On the right side of the screen, the menu selections can be selected with the Up and Down
Buttons. Use the Select Button to choose an item. Selecting one of these items will change to a
different screen with additional controls.
102°F
Set: 104°F
8:32 PM
Ozone
Filter 1
High Range
Spa
Scene
Settings
Ready in Rest Mode
Heating
MESSAGES
At the bottom of the screen, messages may appear at various times. Some of these messages must
be dismissed by the user See “General Messages” section.
PRESS-AND-HOLD
If an Up or Down button is pressed and held when the Set Temperature is selected, the temperature will continue to change until the button is released, or the Temperature Range limits are
reached.
DO NOT DIVE.
40
SPA CONTROLS
The Spa Screen & Scenes
ALL EQUIPMENT ACCESS
The Spa Screen shows all available equipment to control, as well as other features, like Invert, in
one easy-to-navigate screen. The display shows icons that are related to the equipment installed on
a particular spa model, so this screen may change depending on the installation.
The navigation buttons are used to select an individual device. The device that is chosen is highlighted with a white outline and the text under the icon changes to white. Once a device is selected, it can be controlled using the center Select Button.
Some devices, like pumps, may have more than one ON state, so the icon will change to reflect the
state that the equipment is in. Below are some examples of 2-speed Pump indicators.
Jets Off
Jets Low
Jets High
If the Spa has a 24 hour Circ Pump, a Circ Pump Icon will appear to indicate its activity, but outside of Priming Mode, the 24 hour Circ Pump cannot be controlled directly.
NOTE: The icon for the 24 hour pump that is associated with the heater will have a red glow in the
center when the heater is running.
Back
Jets 1
Jets 2
Jets 3
Light
Invert
Ready in Rest Mode
Heating
SCENES
The scenes area will allow you to preset any of the devices to operate when the scene is activated.
There are four different scenes that can be preset. For example if you would like all of the pumps
to turn on at the same time: turn on the pumps, access the scenes area and highlight #1. Once
this is set anytime you highlight the #1 scene all of the pumps will activate. To store a specific
scene tap and hold the highlighted scene for 5 seconds until the display shows “scene stored” in
the bottom left corner.
DO NOT DIVE.
41
SPA CONTROLS
The Settings Screen
PRESSING A “BUTTON”
When instructions are given to “press a button” any of the following can be done:
•N
avigate to the desired item on any Screen. When the desired item is highlighted, press the
Select Button.
PROGRAMMING, ETC.
The Settings Screen is where all programming and other spa behaviors are controlled.
This screen has several features that can be acted on directly. These features include Temp Range,
Heat Mode, and Invert Panel. When one of these items is highlighted, the Select Button is used to
toggle between two settings.
All other menu items (with an arrow pointing to the right) go to another level in the menu.
PRESS-AND-HOLD
If an Up or Down button is pressed and held when an item in a Menu List is highlighted, the list
can be scrolled quickly from top to bottom. The scroll bar on the right side of the screen indicates
the relative position of the highlighted item in the list.
Settings
Back
Temp Range High
Ready
Heat Mode
Time of Day
Filter Cycles
Light Cycle
Invert Panel Normal
Lock
DUAL TEMPERATURE RANGES (HIGH VS. LOW)
This system incorporates two temperature range settings with independent set temperatures. The
specific range can be selected on the Settings screen and is visible on the Main Screen in the upper
right corner of the display.
These ranges can be used for various reasons, with a common use being a “ready to use” setting
vs. a “vacation” setting. Each range maintains its own set temperature as programmed by the
user. This way, when a range is chosen, the spa will heat to the set temperature associated with
that range.
High Range can be set between 80°F and 104°F.
Low Range can be set between 50°F and 99°F.
Freeze Protection is active in either range.
DO NOT DIVE.
42
SPA CONTROLS
The Settings Screen
HEAT MODE – READY VS. REST
In order for the spa to heat, a pump needs to circulate water through the heater. The pump that
performs this function is known as the “24 hour Circ.”
REST Mode will only allow heating during programmed filter cycles.
Circulation Mode See “Spa Behavior” section.
The heater pump generally runs continuously. Since the heater pump is always running, the spa
will maintain set temperature and heat as needed in Ready Mode, without polling.
In Rest Mode, the spa will only heat to set temperature during programmed filter times, even
though the water is being filtered constantly when in Circulation Mode.
Settings
Back
Temp Range High
Ready
Heat Mode
Time of Day
Filter Cycles
Light Cycle
Invert Panel Normal
Lock
READY-IN-REST MODE
READY/REST appears in the display if the spa is in Rest Mode and the Jets 1 Button is pressed. It is
assumed that the spa is being used and will heat to set temperature. After 1 hour, the System will
revert to Rest Mode. This mode can also be reset by entering the Settings Menu and changing the
Heat Mode.
DO NOT DIVE.
43
SPA CONTROLS
Initial Start-Up
PREPARATION AND FILLING
Fill the spa to its correct operating level. Be sure to open all valves and jets in the plumbing system
before filling to allow as much air as possible to escape from the plumbing and the control system
during the filling process.
After turning the power on at the main power panel, the top-side panel will display a splash, or
startup screen.
PRIMING MODE
After the initial start-up sequence, the control will enter Priming
Mode and display a Priming Mode screen. Only pump icons
appear on the priming mode screen. The system will automatically return to normal heating and filtering at the end of the priming
mode, which lasts 4-5 minutes. During the priming mode, the
heater is disabled to allow the priming process to be completed
Priming Mode
without the possibility of energizing the heater under low-flow
or no-flow conditions. Nothing comes on automatically, but the
pump(s) can be energized by selecting the “Jet” buttons. The 24 hour Circ Pump can be activated
by pressing the dedicated “Light” button during Priming Mode.
Exit
Jets 1
Jets 2
Jets 3
Circ
Manually exit Priming Mode by pressing the “Exit” Button.
PRIMING THE PUMPS
As soon as the Priming Mode screen appears on the panel, select the “Jets 1” button once to start
Pump 1 in low-speed and then again to switch to high-speed. Also, select the other pumps, to turn
them on. The pumps should be running in high-speed to facilitate priming. If the pumps have not
primed after 2 minutes, and water is not flowing from the jets in the spa, do not allow the pumps
to continue to run. Turn off the pumps and repeat the process. Note: Turning the power off and
back on again will initiate a new pump priming session. Sometimes momentarily turning the pump
off and on will help it to prime. Do not do this more than 5 times. If the pump(s) will not prime,
the pump(s) will need relieved of an air lock. See Installation Instructions for information on bleeding air from a pump to relieve an air lock. If you need further assistance, your spa dealer can be
contacted. Regular maintenance procedures would not be covered under the spa warranty.
Important: A pump should not be allowed to run without priming for more than 2 minutes. Under
NO circumstances should a pump be allowed to run without priming beyond the end of the 4-5
minute priming mode. Doing so may cause damage to the pump and cause the system to energize
the heater and go into an overheat condition.
EXITING PRIMING MODE
You can manually exit Priming Mode by navigating to the “Back” button on the Priming Mode
Screen. Note that if you do not manually exit the priming mode as described above, the priming mode will be automatically terminated after 4-5 minutes. Be sure that the pump(s) have been
primed by this time.
Once the system has exited Priming Mode, the top-side panel will display the Main Screen, but the
display will not show the temperature yet, as shown below. This is because the system requires
approximately 1 minute of water flowing through the heater to determine the water temperature
and display it.
– – –°F–
DO NOT DIVE.
– –°C
44
SPA CONTROLS
Spa Behavior
PUMPS
On the Spa Screen, select a “Jets” button once to turn the pump on or off, and to shift between
low- and high-speeds if equipped. If left running, the pump will turn off after a time-out period.
The pump 1 low-speed will time out after 30 minutes. The high-speed will time-out after 15 minutes.
CIRCULATION PUMP MODES
The 24 hour circ pump operates continuously with the exception of turning off for 30 minutes at
a time when the water temperature reaches 3°F (1.5°C) above the set temperature (most likely to
happen in very hot climates).
FILTRATION AND OZONE
The system is factory-programmed with one filter cycle that will run in the evening (assuming the
time-of-day is properly set) when energy rates are often lower. The filter time and duration are
programmable. See Adjusting Filtration” section. A second filter cycle can be enabled as needed.
At the start of each filter cycle, the pumps will run briefly to purge the plumbing to maintain good
water quality. On spas equipped with 24 hour circulation systems the filter cycles cannot be set.
(See adjusting filtration section).
FREEZE PROTECTION
If the temperature sensors within the heater detect a low enough temperature, then the pumps
automatically activate to provide freeze protection. The pumps will run either continuously or periodically depending on conditions. If the temperature sensors detect a drop to below 44°F/6.7°C
within the heater, the pump will automatically activate to provide freeze protection. The equipment stays on until 4 minutes after the sensors detect that the spa temperature has risen to
45°F/7.2°C or higher.
CLEAN-UP CYCLE
When a pump is turned on by a button press, a clean-up cycle begins 30 minutes after the pump
is turned off or times out. The pump and the ozone generator will run for 30 minutes or more,
depending on the system. This setting can be changed. See “Preferences” section.
DO NOT DIVE.
45
SPA CONTROLS
Time-of-Day
BE SURE TO SET THE TIME-OF-DAY
Setting the time-of-day is important for determining filtration times and other background features.
“Set Time” will appear on the display if no time-of-day is set in the memory.
On the Settings Screen, select the Time-of-Day line. On the Time-of-Day screen, simply navigate
right and left to select the Hour, Minutes, AM/PM and 12/24 Hour segments. Use the Up and
Down Buttons to make changes.
Time of Day
Back
12 :00 PM
12 HR
SAVING SETTINGS
The Time-of-Day screen is a simple, editable screen that illustrates a feature of the control that
applies to all other editable screens as well.
When changes are made, the icon to go “Back” changes to “Save” and a new icon for “Cancel”
appears under the Save icon. Navigating to the left will highlight the Save icon, and navigating
down from there will allow the user to cancel the pending change. Pressing the “Select” button
will save or cancel the changes and go back to the previous screen.
Time of Day
Back
Save
12 :00
10:
05 PM
PM
12 HR
Cancel
NOTE:
If power is interrupted to the system, Time-of-Day will be maintained for several days.
DO NOT DIVE.
46
SPA CONTROLS
Adjusting Filtration
NOTE:
On spas that are equipped with a 24 hour circulation system the filter cycles are disabled. The
water is filtered 24 hours a day so a filtration cycle is not necessary. The energy efficiency of the
spa is also enhanced by disabling the filtration cycles. Although the filtration settings screens will
still be visible they will not have any effect on filtration cycles.
On spas that are not equipped with 24 hour circulation systems the filtration settings will set times
for the #1 jet pump to run on low speed for filtration.
MAIN FILTRATION
Using the same navigation and adjustment as Setting the Time, Filter Cycles are set using a start
time and a duration. Each setting can be adjusted in 15-minute increments. The panel calculates
the end time and displays it automatically.
Filter Cycles
Back
Filter Cycles
Filter Cycle 1
Starts at 12:00 AM
Runs 0 HR 0 Min
Ends at 12:00 AM
Back
Save
Filter Cycle 2 NO
Starts at 12:00 AM
Runs 0 HR 0 Min
Ends at 12:00 AM
Cancel
Filter Cycle 1
Starts at 6:15 AM
Runs 3 HR 0 Min
Ends at 9:15 AM
Filter Cycle 2 NO
Starts at 12:00 AM
Runs 0 HR 0 Min
Ends at 12:00 AM
FILTER CYCLE 2 - OPTIONAL FILTRATION
Filter Cycle 2 is OFF by default.
Simply navigate to the Filter Cycle 2 line by pressing the Right Navigation Button, and when “NO”
is highlighted, press Up or Down to toggle Filter Cycle 2 on and off. When Filter Cycle 2 is ON, it
can be adjusted in the same manner as Filter Cycle 1 by navigating to the right.
It is possible to overlap Filter Cycle 1 and Filter Cycle 2, which will shorten overall filtration by the
overlap amount.
CIRCULATION PUMP MODES
The 24 Circ Pump is programmed to operate continuously. The 24 hour circ pump operates continuously with the exception of turning off for 30 minutes at a time when the water temperature
reaches 3°F (1.5°C) above the set temperature (most likely to happen in very hot climates).
Purge Cycles
In order to maintain sanitary conditions, as well as protect against freezing, will purge water from
their respective plumbing by running briefly at the beginning of each filter cycle. The spa will
always initiate purge cycles whether it is equipped with a 24 hour circulation system or not to
insure that water is purged from the plumbing lines.
If the Filter Cycle 1 duration is set for 24 hours, enabling Filter Cycle 2 will initiate a purge when
Filter Cycle 2 is programmed to begin.
DO NOT DIVE.
47
SPA CONTROLS
Additional Settings
INVERT PANEL
Selecting Invert Panel will flip the display and the buttons so the panel can be easily operated from
inside or outside the hot tub.
Dedicated Buttons
SPECIFIC BUTTONS FOR SPECIFIC DEVICES
The panel has dedicated function buttons installed, pressing those buttons will activate the device
indicated for that button.
These dedicated buttons will operate just like the Spa Screen buttons and the equipment will
behave in the same manner with each button press.
DO NOT DIVE.
48
SPA CONTROLS
Restricting Operation
The control can be restricted to prevent unwanted use or temperature adjustments.
Locking the Panel prevents the controller from being used, but all automatic functions are still
active.
Locking the Settings allows Jets and other features to be used, but the Set Temperature and other
programmed settings cannot be adjusted.
Settings Lock allows access to a reduced selection of menu items. These include Set Temperature,
Invert, Lock, Utilities, Information and Fault Log. They can be seen, but not changed or edited.
Lock
Back
Settings
Panel
OFF
OFF
Unlocking
102°F
Set: 104°F
8:32 PM
Ozone
Filter 1
Lock
High Range
Unlock
Back
Settings
Panel
OFF
ON
Ready in Rest Mode
Heating
An Unlock Sequence using the navigation buttons can be used from the Lock Screen. The Unlock
Sequence is the same for both Panel Lock and Settings Lock.
DO NOT DIVE.
49
SPA CONTROLS
Additional Settings
HOLD MODE
Hold Mode is used to disable the pumps during service functions like cleaning or replacing the
filter. Hold Mode will last for 1 hour unless the mode is exited manually. If spa service will require
more than an hour, it may be best to simply shut down power to the spa.
Utilities
The Utilities Menu contains the following:
A/B Temps
When this is set to On, the temperature display will alternate to display temperature from Sensor A
and Sensor B in the heater.
Fault Log
The Fault Log is a record of the last 24 faults that can be reviewed by a service tech.
Fault Log
Entry 2
Message Code M026
1 Days Ago 2:21PM
Rest Mode
High Range
Set Temp 104°F
Sensors: A: 100 B: 96
Message:
Sensors are out of sync
Back
DO NOT DIVE.
50
SPA CONTROLS
Additional Settings
PREFERENCES
The Preferences Menu allows the user to change certain parameters based on personal preference.
Preferences
Back
Temp Display
Time Display
Reminders
Cleanup
Dolphin
Color
Language
°F
12 HR
On
0.5 HR
5
Blue
English
Temp Display
Change the temperature between Fahrenheit and Celsius.
Time Display
Change the clock between 12 hr and 24 hr display.
Cleanup
Cleanup Cycle Duration default is 30 minutes. The duration can be set in 30 minute increments
for up to 4 hours. 30 minutes after any of the jet pumps have been activated, the #1 jet pump
will run low speed for the set cleanup cycle duration. If the #1 jet pump does not have low speed,
this may not apply.
Color
Pressing the Select Button when Color is highlighted will cycle through 5 background colors available in the control.
Language
Change the language displayed on the panel.
DO NOT DIVE.
51
SPA CONTROLS
Information
SYSTEM INFORMATION
The System Information Menu displays various settings and identification of the particular system.
As each item in the menu is highlighted, the detail for that item is displayed at the bottom of the
screen. These settings are for information only and cannot be changed.
System Information
Back
Software ID (SSID)
System Model
Current Setup
Configuration Signature
Heater Voltage
Heater Type
Software ID (SSID):
M100_101 V0.6
Software ID (SSID)
Displays the software ID number for the System.
System Model
Displays the Model Number of the System.
Current Setup
Displays the currently selected Configuration Setup Number.
Configuration Signature
Displays the checksum for the system configuration file.
Heater Voltage (Feature not used on CE rated systems.)
Displays the operating voltage configured for the heater.
Heater Wattage as Configured in Software (CE Systems Only.)
Displays a heater kilowatt rating as programmed into the control system software (1-3 or 3-6).
Heater Type
Displays a heater type ID number.
Dip Switch Settings
Displays a number that represents the DIP switch positions of S1 on the main circuit board.
Panel Version
Displays a number of the software in the topside control panel.
DO NOT DIVE.
52
SPA CONTROLS
General Messages
Most messages and alerts will appear at the bottom of the normally used screens.
Several alerts and messages may be displayed in a sequence.
Some messages can be reset from the panel. Messages that can be reset will appear with a “right
arrow” at the end of the message. This message can be selected by navigating to it by pressing the
Select button.
– – –°F–
– –°C
WATER TEMPERATURE IS UNKNOWN
After the pump has been running for 1 minute, the temperature will be displayed.
POSSIBLE FREEZING CONDITION
A potential freeze condition has been detected. All pumps are activated.
In some cases, pumps may turn on and off and the heater may operate during Freeze Protection.
This is an operational message, not an error indication.
THE WATER IS TOO HOT
The system has detected a spa water temp of 110°F (43.3°C) or more, and spa functions are
disabled. System will auto reset when the spa water temp is below 108°F (42.2°C). Check for
extended pump operation or high ambient temp.
DO NOT DIVE.
53
SPA CONTROLS
Heater-Related Messages
THE WATER FLOW IS LOW
There may not be enough water flow through the heater to carry the heat away from the heating
element. Heater start up will begin again after about 1 min. See “Flow Related Checks” below.
THE WATER FLOW HAS FAILED*
There is not enough water flow through the heater to carry the heat away from the heating element and the heater has been disabled. See “Flow Related Checks” below. After the problem has
been resolved, you must press any button to reset and begin heater start up.
THE HEATER MAY BE DRY*
Possible dry heater, or not enough water in the heater to start it. The spa is shut down for 15 min.
Press any button to reset the heater start-up. See “Flow Related Checks” below.
THE HEATER IS DRY*
There is not enough water in the heater to start it. The spa is shut down. After the problem has
been resolved, you must clear the message to restart heater start up. See “Flow Related Checks”
below.
THE HEATER IS TOO HOT*
One of the water temp sensors has detected 118°f (47.8°C) in the heater and the spa is shut
down. You must clear the message when water is below 108°f (42.2°C). See “Flow Related
Checks” below.
FLOW-RELATED CHECKS
Check filters for possible blockage. Try cleaning or replacing filters (especially if spa is equipped
with 24 hour circulation pump).
Check for low water level, clogged filters, suction flow restrictions, closed valves, trapped air, too
many closed jets and pump prime.
On some systems, even when spa is shut down by an error condition, some equipment may occasionally turn on to continue monitoring temperature or if freeze protection is needed.
* This message can be reset from the topside panel.
DO NOT DIVE.
54
SPA CONTROLS
Sensor-Related Messages
SENSORS ARE OUT OF SYNC
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
SENSORS ARE OUT OF SYNC -- CALL FOR SERVICE*
The temperature sensors ARE out of sync. The fault above has been established for at least 1 hour.
Call for Service.
SENSOR A FAULT, SENOR B FAULT
A temperature sensor or sensor circuit has failed. Call for Service.
Miscellaneous Messages
COMMUNICATIONS ERROR
The control panel is not receiving communication from the System. Call for Service.
TEST SOFTWARE INSTALLED
The Control System is operating with test software. Call for Service.
°F OR °C IS REPLACED BY °T
The Control System is in Test Mode. Call for Service.
* This message can be reset from the topside panel.
DO NOT DIVE.
55
SPA CONTROLS
System-Related Messages
PROGRAM MEMORY FAILURE*
At Power-Up, the system has failed the Program Checksum Test. This indicates a problem with the
firmware (operation program) and requires a service call.
THE SETTINGS HAVE BEEN RESET (PERSISTENT MEMORY ERROR)*
Contact your dealer or service organization if this message appears on more than one power-up.
THE CLOCK HAS FAILED*
Contact your dealer or service organization.
CONFIGURATION ERROR (SPA WILL NOT START UP)
Contact your dealer or service organization.
A PUMP MAY BE STUCK ON
Water may be overheated. POWER DOWN THE SPA. DO NOT ENTER THE WATER. Contact your
dealer or service organization.
HOT FAULT
A Pump Appears to have been Stuck ON when spa was last powered
POWER DOWN THE SPA. DO NOT ENTER THE WATER. Contact your dealer or service organization.
* This message can be reset from the topside panel.
DO NOT DIVE.
56
Wi-Fi Module (if equipped)
Remotely control the operations of your spa via an optional integrated Wi-Fi module that
works with the Balboa Water Group Wi-Fi Spa Control App. This app is available for Apple® or
Android® devices. Please refer to the Balboa Water Group website and mobile device app for
operation information.
http://www.balboawater.com/bwa
Note: WiFi Module is not available for all spa models. If this options was not added from the
factory, see your Master Spas dealer for further details and compatibility.
DO NOT DIVE.
100
57
Deluxe Fusion Air Stereo Option (if equipped)
The Deluxe Fusion Air option offers Bluetooth and FM audio modes. This system includes a water
resistant, wireless remote for switching modes and controlling the audio.
Warning: Never remain in your spa longer than 15 minutes per session when the water temperature is above 98˚F. If you wish to spend more time in your spa, whether enjoying music, or just
lounging, be sure to keep the spa water at or below body temperature (98.6˚F).
1.1 POWER ON
The Standard Fusion Air Stereo is always ready any time the spa is on and running.
1.2 REMOTE CONTROL
In order to prolong remote battery life the LCD will shut off in 20 seconds if no other button is pressed. To turn remote back on press any key
once and then press the command desired.
Turn off DSP to access control of Bass and Treble.
When in Bluetooth mode Repeat and Random playback functions must
be enabled via your media device and not from the remote control.
Buttons
Power
Music Mode: Bluetooth
FM Radio Mode
Press Once: Turns remote control on.
Press Twice: Toggle from Operation mode to Standby mode or vice-versa.
Mode
Press once: Change the source.
Press and hold: No function
Press once: Change the source.
Press and hold: No function
Search/Audio
Press once: Search
Press and hold: Audio Menu (BAS-TREBAL-FAD-EUR-DXMONO-STEREO)
Press once: Audio Menu (BAS-TRE-BALFAD-EUR-DX-MONOSTEREO)
Press and hold: Audio Menu (BAS-TRE-BALFAD-EUR-DXMONO-STEREO)
Volume Up
Press once: Volume up
Press and hold: Fast volume up
Press once: Volume up
Press and hold: Fast volume up
Volume Down
Press once: Volume down
Press and hold: Fast volume down
Press once: Volume down
Press and hold: Fast volume down
Play/Pause
Press once: Play/Pause
Press and hold: No function
Press once: Toggle mute
Press and hold: No function
Fast Rewind
Press once: Previous track
Press and hold: Fast rewind
Press once: Scan down
Press and hold: Toggle manual seeking
Fast Forward
Press once: Next track
Press and hold: Fast forward
Press once: Scan up
Press and hold: Toggle manual seeking
1 / DIR-
Press once: Back to previous folder
Press and hold: No function
Press once: Listen to FM preset station 1
Press and hold: Set preset FM station 1
2 / REPEAT
Press once: Repeat playback function
Press and hold: Repeat function
Press once: Listen to FM preset station 2
Press and hold: Set preset FM station 2
3 / DIR+
Press once: Forward to next folder
Press and hold: No function
Press once: Listen to FM preset station 3
Press and hold: Set preset FM station 3
12V Trigger /
Random
Press once: Random playback function
No Function
DO NOT DIVE.
100
58
Deluxe Fusion Air Stereo Option
1.3 HANDHELD REMOTE CONTROL BATTERY INSTALL
Unscrew the waterproof cap on the back of the remote control. Place the CR-2450 battery in the
RF remote control and replace the water/dust proof cap. When the battery is installed, the remote
control LCD should be solid and bright without any flickering.
1.4 HANDHELD REMOTE CONTROL SYNCHRONIZING
The remote should already be paired from the factory, but if you need to re synchronize the
remote follow the steps below.
POWER button on the remote control to turn on the remote.
1. Press the
2. The LCD will become illuminated and read ‘NO LINK’.
3. Press and hold the
MODE button for 5 – 10 seconds.
4. Once the remote has been paired, the LCD will display one of the audio modes (BT AUDIO or
AUX).
For any additional remote controls, you will also need to activate/synchronize those remote controls
by following the steps above.
If the pairing process is not effective, check the battery voltage of the remote. If above 3V DC
refer to section 1.5 above top make sure the battery is installed correctly. If battery voltage is
below 3V DC replace the battery.
If the LCD displays “NO LINK” in any mode, this means the remote is out of reception range or
not paired correctly. Move the remote closer to the unit and try again.
If you lose your remote control and buy a new remote control, please follow the above to pair
remote control.
2.1 PAIR WITH BLUETOOTH DEVICE
1. Switch on your Bluetooth device.
2. Select ‘AQUATIC AV’ from the list of available devices to pair (no password is needed).
Only one Bluetooth device can be paired with the BlueCube Media Player at any time.
2.2 LISTENING VIA BLUETOOTH DEVICE
1. Bluetooth mode will be activated once a Bluetooth device is paired.
2. Play the song from device and the sound will play through the BlueCube Media Player.
3. Press
(PLAY/PAUSE) to play/pause the song.
4. Press
/
(FAST REWIND/FORWARD) buttons to play previous/next song file.
5. Track and volume can be controlled directly from your Bluetooth device or remote control.
DO NOT DIVE.
DO NOT DIVE.
59
101
Deluxe Fusion Air Stereo Option
3.1 LISTENING VIA FM
1. Press
(MODE) on remote control to switch to FM radio mode.
If this is the first time you listen to FM radio, the default frequency will be 87.5MHz, as shown
on the remote LCD.
FM radio is only available when you are in the FM Radio mode.
3.2 SCAN OR SEEK FM RADIO CHANNELS
1. Press
(FAST REWIND) or
2. Press and hold either
forward.
(FAST FORWARD) to seek another station.
(FAST REWIND) or
(FAST FORWARD) for manual tuning back or
After using Seek mode the unit will automatically switch back into Scan mode after 20 seconds.
3.3 SAVING RADIO CHANNEL TO MEMORY
To save the current frequency into memory, press and hold
onds. The station will be stored into relevant button.
,
or
for more than 2 sec-
3.4 LISTENING TO SAVED RADIO MEMORY
Press the
,
or
preset button once to listen to the station stored in that button.
3.5 SWITCH BETWEEN US AND EUROPEAN FM MODES
1. Make sure dock and remote are turned on and in ‘RADIO’ mode.
2. Press the AUDIO button 6 time in a row.
3. The remote will display ‘AREA USA’ or ‘AREA EUR’ depending on which tuning mode is currently selected.
4. Use the
5. Press
and
buttons to switch between US or European modes.
PLAY/PAUSE) to select the desired tuning mode.
6. Once you switch modes it will default to the FM station stored in ‘PRESET’.
US mode will increase and decrease the FM frequency in steps of 0.1 MHz, e.g. 88.5, 88.6,88.7
MHz. EUR mode will increase and decrease the FM frequency in steps of 0.05 MHz, e.g. 88.25,
88.30, 88.35 MHz.
When in Seek mode and European FM tuning mode, all frequency steps will be visible.
4.1 ADJUST VOLUME LEVEL
1. Press
(VOLUME UP) once to increase the volume.
2. Press
(VOLUME DOWN) once to reduce the volume.
3. Press and hold either
volume continuously.
DO NOT DIVE.
or
and the BlueCube Media Player will increase or decrease audio
102
60
Deluxe Fusion BT Stereo Option (if equipped)
Warning:
Never remain in your spa longer than 15 minutes per session when the water temperature is above
98˚F. If you wish to spend more time in your spa, whether enjoying music, or just lounging, be sure to keep the
spa water at or below body temperature (98.6˚F).
CAUTION – Risk of Electric Shock. Do not operate the audio controls while inside the spa.
CAUTION – Risk of Electric Shock. Do not operate, open, shut or connect devices
to dock with wet hands.
CAUTION – Risk of Electric Shock. Do not leave compartment door open.
CAUTION – Risk of Electric Shock. Replace components only with identical components.
WARNING – Prevent Electrocution. Do not connect any auxiliary/external components to the
system (i.e. cables, additional speakers, headphones, additional Audio/Video components, etc.).
NOTE: These units are not provided with an outdoor antennae; if added, it should be installed in
accordance with article 810 of the National Electrical Code, ANSI / NFPA 70.
NOTE: Do not service this product yourself as opening or removing covers may expose you
to dangerous voltage or other risk of injury. Refer all servicing to qualified service personnel.
DO NOT DIVE.
100
61
Deluxe Fusion BT Stereo Option –
Location of Controls
9
2
4
5
1
3
7
6
10
8
11
1.1 DIGITAL MEDIA LOCKER CONTROLS
1. Open/Close Latch & Protective Door
2. Power ON/OFF Button
3. Water/Dust Protection Inner Gasket
4. 3.5mm Aux Input for MP3 Devices
5. Power ON/OFF LED
6. Security Strap for digital media devices
7. USB Connector
8. Door Control Keypad
9. LED Mode Indicator
10. Back lighting
11. Cable Storage Tray
DO NOT DIVE.
101
62
Deluxe Fusion BT Stereo Option –
Location of Controls
1.2 DOOR KEYPAD CONTROLS
Buttons
Music Mode: iPhone, iPod,
Bluetooth, USB & MP3
FM Radio Mode
Power
Press once: Toggle from Operation mode to Standby mode or vice-versa.
Mode
Press once: Change the source.
Press and hold: No function
Press once: Change the source.
Press and hold: No function
Volume Up
Press once: Volume up
Press and hold: Fast volume up
Press once: Volume up
Press and hold: Fast volume up
Volume Down
Press once: Volume down
Press and hold: Fast volume down
Press once: Volume down
Press and hold: Fast volume down
Fast Rewind
Press once: Previous track
Press and hold: Fast rewind
Press once: Scan down
Press and hold: Toggle manual seeking
Fast Forward
Press once: Next track
Press and hold: Fast forward
Press once: Scan up
Press and hold: Toggle to manual
seeking
12V Trigger /
Random
Press once: Random playback
Press and hold: Toggle 12V on/off
Press once: No function
Press and hold: Toggle external 12V
power on/off
Play/pause
Press once: Play/Pause
Press and hold: No function
Press once: Toggle mute
Press and hold: No function
1 / DIR-
Press once: Back to previous folder
Press and hold: No function
Press once: Listen to FM preset station
1
Press and hold: Set preset FM station 1
2 / REPEAT
Press once: Repeat function
Press and hold: No function
Press once: Listen to FM preset station
2
Press and hold: Set preset FM station 2
3 / DIR+
Press once: Forward to next folder
Press and hold: No function
Press once: Listen to FM preset station
3
Press and hold: Set preset FM station 3
The keypad on the door has a set of keys fewer than those on the remote but has exactly
the same functions correspondingly. This keypad allows you to operate the dock without the
remote control.
DO NOT DIVE.
102
63
Deluxe Fusion BT Stereo Option –
Location of Controls
If your music player is connected via the Auxiliary input you will
not be able to control track or receive track information.
In order to prolong remote battery life the LCD will shut off in
20 seconds if no other button is pressed. To turn remote back
on press any key once and then press the command desired.
Turn off DSP to access control of Bass and Treble.
1.3 REMOTE CONTROL
When in Bluetooth mode Repeat and Random playback functions must be enabled via your media device and not from the
remote control.
Buttons
Music Mode: iPhone, iPod,
Bluetooth, USB & MP3
Power
Press Once: Turns remote control on.
Press Twice: Toggle from Operation mode to Standby mode or vice-versa.
Mode
Press once: Change the source.
Press and hold: No function
Press once: Change the source.
Press and hold: No function
Search/Audio
Press once: Search
Press and hold: Audio Menu (BAS-TREBAL-FAD-EUR-DXMONO-STEREO)
Press once: Audio Menu (BAS-TRE-BALFAD-EUR-DX-MONOSTEREO)
Press and hold: Audio Menu (BAS-TREBAL-FAD-EUR-DXMONO-STEREO)
Volume Up
Press once: Volume up
Press and hold: Fast volume up
Press once: Volume up
Press and hold: Fast volume up
Volume Down
Press once: Volume down
Press and hold: Fast volume down
Press once: Volume down
Press and hold: Fast volume down
Play/Pause
Press once: Play/Pause
Press and hold: No function
Press once: Toggle mute
Press and hold: No function
Fast Rewind
Press once: Previous track
Press and hold: Fast rewind
Press once: Scan down
Press and hold: Toggle manual seeking
Fast Forward
Press once: Next track
Press and hold: Fast forward
Press once: Scan up
Press and hold: Toggle manual seeking
1 / DIR-
Press once: Back to previous folder
Press and hold: No function
Press once: Listen to FM preset station 1
Press and hold: Set preset FM station 1
2 / REPEAT
Press once: Repeat playback function
Press and hold: Repeat function
Press once: Listen to FM preset station 2
Press and hold: Set preset FM station 2
3 / DIR+
Press once: Forward to next folder
Press and hold: No function
Press once: Listen to FM preset station 3
Press and hold: Set preset FM station 3
12V Trigger /
Random
Press once: Random playback function
Press and hold: Toggle external
Press once: No function
Press and hold: Toggle external 12V power
on/off
DO NOT DIVE.
103
64
FM Radio Mode
Deluxe Fusion BT Stereo Option –
Getting started
2.1 REMOTE CONTROL BATTERY INSTALL
Remove the RF wireless remote control from the Digital Media Locker box. Unscrew the waterproof
cap on the back of the remote control. Place the CR-2450 battery in the RF remote control and
replace the water/dust proof cap.
When the battery is installed, the remote control LCD should be solid and bright without any flickering.
2.2 POWER ON
Press the
on/off button.
Red Light: Power to the docking station is ON, but the unit is in standby mode.
Blue Light: The unit is powered ON and looking for an audio source.
For applications that require low current draw and where battery drain may occur, the power button must be turned OFF inside the unit. When the power button is in the OFF position the red LED
will not be lit.
For applications where a 12V battery is not used, such as in a Spa, the power button can be left
ON and the remote control or door controls can then be used to power on/off accordingly.
2.3 REMOTE CONTROL SYNCHRONIZING
1. Turn the Digital Media Locker to off mode with the power button inside the door. The LED
should not be illuminated.
2. Press the red
(POWER) button on the remote.
3. Press and hold the
(MODE) button until the LCD reads PAIR.
4. Continue to press and hold the
(MODE) button during step 5 below.
5. Turn the docking station to standby mode (within 10 seconds) with the on/off button inside
door (the red LED will illuminate and then turn blue).
6. The remote’s LCD should read WELCOME or show a mode position such as RADIO, USB, BT or
AUX IN.
For any additional remote controls, you will also need to activate/synchronize those remote controls
by following the steps above.
If the pairing process is not effective, switch the locker off using the on/off button located
inside the door of the dock. Unplug the 12-pin Harness on the back of the Locker for 3 minutes. Reattach the Harness and repeat steps 1-6 above.
If the pairing process is not effective, check the battery voltage. If above 3V DC refer to section 1.5 above top make sure the battery is installed correctly. If battery voltage is below 3V
DC replace the battery.
If the LCD displays “NO LINK” in either mode, this means the remote is out of reception range.
Move the remote closer to the Locker and try again.
If you lose your remote control and buy another new remote control, please follow the above
to start pairing before normal usage.
DO NOT DIVE.
104
65
Deluxe Fusion BT Stereo Option –
Listening to Devices
3.1 LISTENING VIA USB
1. Power up the Digital Media Locker
2. Attach your device to the USB cable inside the Digital Media Locker using the appropriate USB
adaptor.
3. Secure the device with the anchor straps provided.
4. Secure the Digital Media Locker’s protective door.
5. Press
(POWER) on the remote control or Power button on the locker to turn it ON.
6. Press
(MODE) on the remote control to select USB mode. Use the buttons as shown in the
remote function chart.
Always ensure to connect and disconnect your media player with dry hands!
3.1.1.1 USB SEARCH
1. When using a USB device, press
(SEARCH) to enter the USB searching mode.
2. Use
and
(Volume UP/DOWN) to scroll through the folders on your USB device and to
select a folder press the
(PLAY/PAUSE) button.
3. Use
and
(Volume UP/DOWN) to scroll through the songs in the folder and press
(PLAY/PAUSE) to play the desired song.
3.1.1.2 IPHONE & IPOD SEARCH
1. When using an iPhone or iPod, press
(SEARCH) to enter iPod searching mode.
2. Once in searching mode the remote will display ‘Playlist’. Continue to press
scroll through the search modes below:
(SEARCH) to
1) Playlist 2) Artist 3) Album 4) Song 5) Genre 6) Composer 7) Audio Book
3. Press
4. Use
(PLAY/PAUSE) To select the desired search mode.
and
(Volume UP/DOWN) to scroll through your media in the selected search mode.
5. Once you find the desired media press
(PLAY/PAUSE) to make your selection. If your section
is a song it will begin to play, if you select a playlist, artist, album, genre, composer or audio
book, the songs in the selected folder will be visible. Press
(PLAY/PAUSE) to play the desired
song within the folder.
3.1.2 DEVICE CHARGING
When specified USB devices are connected to the USB input the device battery will charge.
DO NOT DIVE.
105
66
Deluxe Fusion BT Stereo Option –
Listening to Devices
3.1.3 IPHONE & IPOD COMPATIBLE MODELS
3.2.1 PAIR WITH BLUETOOTH DEVICE
1. Switch on your Bluetooth device.
2. Select ‘AQUATIC AV’ from the list of available devices to pair (no password is needed).
Only one Bluetooth device can be paired with the Digital Media Locker at any time. If another
device is within range and paired, a new device will not be able to pair/connect. Disconnect
other device or reset power and immediately try pairing new device.
This audio system is compatible with many Bluetooth devices. Master Spas Inc. does not guarantee compatibility with all Bluetooth devices.
3.2.2 LISTENING VIA BLUETOOTH DEVICE
1. Bluetooth mode will be activated once a Bluetooth device is linked.
2. Play the song from device and the sound will play through the Digital Media Locker.
3. Press
(PLAY/PAUSE) to play/pause the song.
4. Press
/
(FAST REWIND/FORWARD) buttons to play previous/next song file.
5. Track and volume can be controlled directly from your Bluetooth device, remote control or door
controls.
3.3 LISTENING VIA AUXILIARY INPUT
1. Power up the Digital Media Locker.
2. Connect your MP3 device to either the 3.5mm Jack input or RCA input
3. Secure the device with the anchor straps provided.
4. Secure the Digital Media Locker’s protective door.
5. Press
(MODE) on the remote control to select ‘AUX IN’ mode.
Only one Auxiliary input (3.5mm Jack or RCA) can be used at any one time.
3.4 ADJUST VOLUME LEVEL
1. Press
(VOLUME UP) once to increase the volume.
2. Press
(VOLUME DOWN) once to reduce the volume.
3. Press
and
hold either or and the Digital Media Locker will increase or decrease audio
volume continuously.
DO NOT DIVE.
106
67
Deluxe Fusion BT Stereo Option –
Listening to FM Radio
4.1 ENTER FM RADIO MODE
1. Press
(MODE) on remote control to switch to FM radio mode.
If this is the first time you listen to FM radio, the default frequency will be 87.5MHz, as shown
on the remote LCD.
FM radio is only available when you are in the FM Radio mode.
4.2 SCAN OR SEEK FM RADIO CHANNELS
1. Press
(FAST REWIND) or
2. Press and hold either
forward.
(FAST FORWARD) to seek another station.
(FAST REWIND) or
(FAST FORWARD) for manual tuning back or
After using Seek mode the unit will automatically switch back into Scan mode after 20 seconds.
4.3 SAVING RADIO CHANNEL TO MEMORY
To save the current frequency into memory, press and hold
onds. The station will be stored into relevant button.
,
or
for more than 2 sec-
4.4 LISTENING TO SAVED RADIO MEMORY
Press the
,
or
preset button once to listen to the station stored in that button.
4.5 SWITCH BETWEEN US AND EUROPEAN FM MODES
1. Make sure dock and remote are turned on and in ‘RADIO’ mode.
2. Press the AUDIO button 6 time in a row.
3. The remote will display ‘AREA USA’ or ‘AREA EUR’ depending on which tuning mode is currently selected.
4. Use the
5. Press
and
buttons to switch between US or European modes.
PLAY/PAUSE) to select the desired tuning mode.
6. Once you switch modes it will default to the FM station stored in ‘PRESET’.
US mode will increase and decrease the FM frequency in steps of 0.1 MHz, e.g. 88.5, 88.6,88.7
MHz. EUR mode will increase and decrease the FM frequency in steps of 0.05 MHz, e.g. 88.25,
88.30, 88.35 MHz.
When in Seek mode and European FM tuning mode, all frequency steps will be visible.
4.6 ADJUST VOLUME LEVEL
1. Press
(VOLUME UP) once to increase the volume.
2. Press
(VOLUME DOWN) once to reduce the volume.
3. Press and hold either
volume continuously.
DO NOT DIVE.
or
and the Digital Media Locker will increase or decrease audio
107
68
Deluxe Fusion BT Stereo Option –
Additional Features
5.1 INTERNAL DOCK LIGHT
Use the trigger on the remote to toggle the internal illumination light ON/OFF.
DO NOT DIVE.
108
69
Mast3rPur (if equipped)
Note: This regular maintenance for the Mast3rPur system is not covered under the warranty of the
spa. Your Master Spas Dealer or Service Center can be contacted to schedule this maintenance.
WARNING:
BEFORE PERFORMING ANY MAINTENANCE ON THE MAST3RPUR SYSTEM, MAKE SURE THE SPA IS
SHUT DOWN.
Upper Enclosure Assembly
Assembly Pin
UV Reactor
Sealing Rings
UV Lamp
Enclosure Base
Quartz Tube
Compression
Washers
Compression Nut
Lamp Connector Plug
Figure 2: Mast3rPur System Exploded View
a. UV Lamp Removal – See Figure 2.
If the Green Power Indicator is on, but the Blue UV Lamp Indicator is off, the UV lamp needs to
be replaced. However, the UV lamp useful life is 18 months. The Lamp must be replaced after
18 months of use, even if the Blue UV Lamp Indicator is still lit.
i.
Make sure the unit is disconnected from power and the lamp has cooled before starting
maintenance.
ii.
Open the Mast3rPur System by removing the screw on the bottom of the Upper Enclosure
Assembly, rotating it up and pushing it back to release it from the Assembly Pin.
iii. Unplug the Lamp Connector Plug attached to the end of the UV Lamp and place the Upper
Enclosure Assembly in a safe place.
iv. Slowly pull the UV Lamp out of the Quartz Tube by the white ceramic prong end. DO NOT
TOUCH THE UV LAMP GLASS WITH YOUR BARE HANDS. The oils on your hands can cause hot
spots on the lamp and shorten its life. If oil from your fingers is left on the lamp glass, clean
it off with a soft towel and rubbing alcohol. If you are removing an old lamp for replacement, handle the lamp carefully and dispose properly (see Environmental Notice below).
v.
Make sure the two o-rings and the end cushion remain on the ceramic ends of the lamp as
it is set aside in a safe place.
DO NOT DIVE.
23
70
Mast3rPur (if equipped)
b. Installing the UV Lamp
i.
Make sure to handle the new lamp as described in Section A and clean the UV Lamp before
installation if needed.
ii.
Slowly place the UV Lamp into the Quartz Tube until it contacts the bottom of the tube.
iii. Connect the Lamp Connector Plug to the pins on the lamp.
NOTE: Do not force the Lamp Connector Plug onto the pins. If force is needed, it means that the
components are misaligned.
ENVIRONMENTAL NOTICE: UV Lamp CONTAINS MERCURY. Manage in accordance with disposal
laws. See: www.lamprecycle.org
c. UV Reactor Service and Maintenance
The UV Lamp is housed in a Quartz Tube. If the Quartz Tube becomes dirty, its ability to transmit
rays from the UV Lamp will be diminished and decrease system performance. The Quartz Tube
should be removed from the UV Reactor at least once a year, or during a routine spa water
change for inspection and cleaning if necessary. DO NOT REMOVE THE QUARTZ TUBE WITH WATER
IN THE SPA
d. Quartz Tube Removal and Cleaning
CAUTION: Wear proper eye and skin protection for servicing glass components.
i.
Make sure the spa is shut down the water removed from the spa, and that the UV Lamp
and Quartz Tube have cooled before performing maintenance on the Quartz Tube.
ii.
Remove the Upper Enclosure Assembly and UV Lamp as described in Section A and set aside
in a safe place.
iii. Remove the plastic Compression Nut. If there is any water remaining in the plumbing, it will
start to leak after the Compression Nut is removed.
iv. Grasp the inside of the Quartz Tube and pull it out of the housing. Make sure the Sealing
Rings and Compression Washers do not get lost during Quartz Tube removal.
v.
Inspect the Sealing Ring for nicks or hardness and the Compression Washers for cracks,
replace if necessary.
vi. Clean the Quartz Tube exterior with a mild solution of muriatic acid and water in a ratio
of four parts water to one part acid (4:1). DO NOT USE ABRASIVE CLEANERS as they can
scratch the high quality quartz glass.
CAUTION: Follow the directions for safe use and handling of muriatic acid on the acid bottle label.
vii. After cleaning the Quartz Tube, wash it off with water and wipe dry with a soft towel.
Inspect the Quartz Tube for cracks and replace if cracks are found.
viii. Make sure the inside of the Quartz Tube is dry before replacing the UV Lamp(s).
NOTE: Damage caused by broken quartz tubes is not covered under the Mast3rPur System Limited
Warranty.
DO NOT DIVE.
23
71
Mast3rPur (if equipped)
CAUTION: If broken glass is trapped in the spa system, do not operate the spa. contact a service professional to have the glass removed.
e. Quartz Tube Installation
i.
Arrange the Sealing Rings and Compression Washers on the Quartz Tube as shown in Figure 3.
Compression
Washers
3/8 in
Sealing Rings
Figure 3: Quartz Tube Seal Assembly Detail
ii.
Insert the Quartz Tube partially into the UV Reactor. Place the Compression Nut over the
open end of the Quartz Tube and slowly push in till it is resting against the threads on the
UV Reactor.
iii. Screw the Compression Nut into the threads till it is finger tight. DO NOT OVERTIGHTEN.
iv. After spa is refilled, turn the spa ON and check the seal around the Quartz Tube for leaks.
v.
Correct any leak found by carefully tightening the Compression Nut no more than one turn.
vi. SHUT DOWN the spa once you have confirmed that there are no leaks.
vii. Install the UV Lamp as described in Section B.
viii. Reinstall the Upper Enclosure Assembly to the Enclosure Base. Make sure the Assembly
Pin is fitted through the hole in flange of the Enclosure Base before you screw the Upper
Enclosure Assembly in place.
ix. The unit is now ready for normal operation.
Contact your Master Spas dealer for replacement Mast3rPur parts.
Note: The ozone hose and check valve connecting between the ozone generator and ozone injector
should be inspected and/or replaced, if necessary, every 12 months. Depending on conditions of the
air which is being brought in to the ozone generator, the ozone hose and check valve can wear more
rapidly. This regular maintenance is not covered under the spa warranty.
DO NOT DIVE.
23
72
Twilight Series is manufactured
by Master Spas, one of the world’s
leading spa manufacturers.
Master Spas Inc.
6927 Lincoln Parkway
Fort Wayne, IN 46804
800.860.7727
[email protected]
www.MasterSpas.com
Master Spas reserves the right to change specifications or features without notice.
Master Spas is a manufacturer of spas and related products and we stand behind every
product we produce pursuant to those representations which are stated in our written
limited warranty. your dealer is an independent business person or company and not an
employee or agent of Master Spas, Inc. We cannot and do not accept any responsibility or
liability for any other representations, statements or contracts made by any dealer beyond
the provisions of our written limited warranty.
POP15TSOM
201412
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement