DSSH SMOKING SHELTER-A.pmd

DSSH SMOKING SHELTER-A.pmd
Vestil Manufacturing Corporation
2999 North Wayne St., Angola, IN 46703
Ph 260-665-7586 • Fax: 260-665-1339
E-mail: sales@vestil.com • www.vestil.com
Revised 01-10
A company dedicated to solving ergonomic and material
handling problems since 1955.
Storage Solutions
OWNER'S
MANUAL
SMOKING SHELTER • MODEL DSSH
CONTENTS
Warnings & Safety Instructions .............................. 1
Tools for Installation ................................................ 1
Replacement Parts ................................................ 1
Assembly Instructions ..........................................2-4
Receiving Instructions ............................................ 1
WARNINGS & SAFETY INSTRUCTIONS
RECEIVING INSTRUCTIONS
Ensure that all employees understand and follow the
following.
• Failure to read and understand this owner’s manual
before using or servicing the LP tank truck
constitutes a misuse of the product. All persons who
will install, use, or care for this product must be familiar
with this material.
• Ensure that all information / safety / warning labels stay
in place and are legible.
• Contact the manufacturer for any needed MSDS
information.
• Do not perform any modifications to the smoking shelter
without the manufacturer’s approval. Failure to receive
authorization for changes to the equipment could void
the warranty.
• Maintenance and repairs are to be done only by
personnel qualified to perform the required work.
Consideration will not be given for warranty repair
charges without prior written authorization by the
manufacturer.
It is possible that this product could incur damage
during transit.
Inspect the unit closely when it arrives. If you see
evidence of damage or rough handling to either the
packaging or to the product when it is being unloaded,
immediately make a note of it on the Bill Of Lading!
It is important that you remove the product’s packaging
upon its arrival to ensure that there is no concealed
damage or to enable a timely claim with the carrier for
freight damage.
Also verify that the product and its specifications are as
ordered.
TOOLS NEEDED FOR INSTALLATION
• Inner hexagon spanner
• M6 & M8 outer hexagon spanner
• M4 & M6 Phillips screwdriver
E
N
G
L
I
S
H
E
S
P
A
N
O
L
REPLACEMENT PARTS
We take pride in using quality parts on the equipment
we manufacture. We are not responsible for equipment
problems resulting from the use of unapproved
replacement parts.
To order replacement or spare parts for this equipment,
contact the factory.
In any communication with the factory please be
prepared to provide the machine’s serial number, which is
indicated on the machine dataplate.
F
R
A
N
Ç
A
I
S
1
ASSEMBLY INSTRUCTIONS
1. SETTING UP SHELVES
Connect the shelves to the columns, matching the column numbers and using the assembly
method shown in Figure 1:
column
Assembling the columns to the base anchors.
a. The 4 screw holes of the base should be aligned to the joint brackets
(1)(4)(6)(7) inside the column.
b. Tighten the inner hexagon screws.
floor
bracket
inner hexagon
screw
Figure 1
Assembling the joint brackets.
a. Align holes in the joint brackets to the holes in the column (see Figure 2).
b. Tighten the inner hexagon screws.
Inner hexagon
c. Insert the cross beam into joint bracket.
M6 screws
d. Drilling the holes are subject to both edge of crossbeam,
then tighten with the M6 countersunk self-tapping screws.
M4 self-tapping
screw
bracket
Figure 2
Assemble the glass clip (see figure 3):
a. Attach one side of the glass clip to the column using M4 screws.
b. Insert glass into glass clips, aligning the holes.
c. Repeat for the other side.
Glass
Glass clip
Column
Figure 3
2
Assembling the gutter (see figure 4):
a. Two gutter opening position should be inserted into inner holes of column (4)(7).
b. Tighten the gutter in place using the screws.
c. Install the bolique beam.
Gutter
Gutter
Support
bracket
Oblique
Beam
Figure 4
Assembling the roof:
a. Attach the roof to the roof frame using self-tapping screws with a rubber gasket.
(figure 5).
b. The middle roof panel is installed on top of the side roof panels. Connect the
extrusions as in Figure 6.
Roof
Column
Oblique
Beam
Oblique
Beam
Roof
Figure 6
Figure 5
Assembling the side, front and back panels:
a. Assemble the left and right panels as shown in figure 7.
b. Repeat for front and back panels.
Left side panel
Roof
Oblique Beam
Cross Beam
Figure 7
3
Assembling the roof.
a. See figure 8. Fasten aluminum angles (17)(18)(19)(20) to cross beams (3)(8)(11)(15)
with M4 self-tapping screws. Tighten screws.
b. Set roof on top of aluminum angles as pictured in figure 9. Fasten both ends of the
ceiling.
Note: Pay attention to the screw hole positions to ensure correct assembly. You must follow
the assembly sequence above.
Column
Beam
Beam
Roof
M4 Self-tapping
screws
Angle
Figure 9
Figure 8
Gutter
Drawing 1
Assembly Shown
Panel
Right
Back
Roof
Front
Left
Drawing 1
Roof Assembly
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising